HomeMy WebLinkAbout1293 CARLSBAD VILLAGE DR; ; AS100055; Permit5/17/24. 10:06 AM AS100055 Permit Data
City of Carlsbad
Sprinkler Permit
Permit No: AS100055
1293 CARLSBAD
Job Address:
VILLAGE DR
Permit Type: SPRINK
Parcel No: 1561907004
Lot #: 0
Reference No.:
PC #:
Project Title: DR. FALLAH
Status: ISSUED
Applied 5/5/2010
Approved: 5/5/2010
Issued: 5/5/2010
Inspector:
Applicant:
CPS FIRE PROTECTION, INC.
417 VERNON WY
EL CAJON, CA
619-590-1101
Owner:
CARLSBAD MEDICAL VILLAGE L P
C/O RUSS RIES
P0 BOX 1422
LA JOLLA CA
Fees ($) Add'l Fees ($) Total ($) Balance ($)
130 0 130 0
about:blank 1/1
Carlsbad Fire Department
Plan Review Requirements Category. SPRINK, TI
Date of Report: 05-24-20 10 Reviewed by:
Name: CPS FIRE PROTECTION, INC.
Address: 417 VERNON WY
EL CAJON, CA
92020
Permit #: AS 100055
Job Name: DR. FALLAH
Job Address: 1293 CARLSBAD VILLAGE DR CBAD
INCO ETE The item you have submitted for r--cviewris-*mcom-1,51t-t-e~=A--tithiY-t-ifffe;~tlus,office cannot
adequately con applicable codes and/or standarIeereview
carefully all cot ments and/or specifications, with changes "clouded",
to tl4ffice.fq .yiew and approval.
Cond: C0N0004030
[MET]
C!!~~
THIS PROJECT HAS BEEN REVIEWED AND APPROVED FOR THE PURPOSES OF ISSUEANCE OF A
BUILDING PERMIT.
THIS APPROVAL IS SUBJECT TO FIELD INSPECTIONS, ANY REQUIRED TESTS, FIRE DEPARTMENT
NOTATIONS,
CONDITIONS IN CORRESPONDENCE AND COMPLIANCE WITH ALL APPLICABLE CODES AND
REGULATIONS.
THIS APPROVAL SHALL NOT BE HELD TO PERMIT OR APPROVE ANY VIOLATION OF THE LAW.
Entry: 05/24/2010 By: cwong
OCT 27 2006 2:31PM CARLSBAD FIRE PREVEFIIIUN fbUbUbbbI
IV
CARLSBAD FIRE PREVENTION DIVISION
1) Permit Application Form
A. Check or fill in pertinent information for type of permit you are submitting.
'~\P AS - Automatic Sprinklers (Check off type ofplww being submitted)
New System —How many risers/levels?____
V Tenant Improvement
Residential - How many systems and/or buildings?
Underground for approval do
Underground included for reference only Total Fees '()
FA - Fire Alarm
25 Devices or less
Over 26 devices 0 of devices
Total Fees
Monitoring System
FS - Fixed Systems (Circle One)
Hood & Duct, Special Chemical Agent Suppression
System, Standpipe, Spray Booth Total Fees
Repeated Inspection fee Is $73.00.
Name of Project: '' t LL
Address ofjob site: (Z 3 cpbtL SA^ #
Building Permit # CB fOC) 5i 3
Contractor Information
Name iz4& 4aj
1 L
Address q1-7 JEr
City, State, Zip L CA Q 2 02-0
Phone O FAX cwl -10—L10 3
Kind of License and Number Q-1*_ -(ocC.j(, Exp. Date
Do you currently have a business license on file with the City of Carlsbad? or No
to 1(31 /it 0
4e4)Zzd'
Signature iIi Date ~5hj _14 _
Please estimate at least 10 business days for plan review comments and/or approval. We will
contact you by telephone when the plans are approved/disapproved. Thank you!
Permit Application Forrn.doc 09125/2006
j
tqCD Fire & Building
IlProducts
Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500
All
Oem
Customer Service/Sales:
Tel: (414)570-5000/(800)558-5236
Fax: (414) 570-5010/(800) 877-1295
Series TY-FRB - 28, 42, 56, and 80 K-factor
Upright, Pendent, and Recessed Pendent Sprinklers
Quick Response, Standard Coverage
General
Description
The Series TY-FAB, 2.8, 4.2, 5.6, and
8.0 K-factor, Upright and Pendent
Sprinklers described in this data sheet
are quick response - standard cover-
age, decorative 3 mm glass bulb type
spray sprinklers designed for use in
light or ordinary hazard, commercial
occupancies such as banks, hotels,
shopping malls, etc.
The recessed version of the Series
TV-FRB Pendent Sprinkler, where ap-
plicable, is intended for use in areas
with a finished ceiling. It uses either a
two-piece Style 10 (1/2 inch NPT) or
Style 40 (3/4 inch NPT) Recessed Es-
cutcheon with 1/2 inch (12,7 mm) of
recessed adjustment or up to 3/4 inch
(19,1 mm) of total adjustment from the
flush pendent position, or a two-piece
Style 20 (1/2 inch NPT) or Style 30(3/4
inch NPT) Recessed Escutcheon with
1/4 inch (6,4 mm) of recessed adjust-
ment or up to 1/2 inch (12,7 mm) of
total adjustment from the flush pen-
dent position. The adjustment provided
by the Recessed Escutcheon reduces
the accuracy to which the fixed pipe
drops to the sprinklers must be cut.
Corrosion resistant coatings, where
applicable, are utilized to extend the
life of copper alloy sprinklers beyond
that which would otherwise be ob-
tained when exposed to corrosive at-
mospheres. Although corrosion resis-
tant coated sprinklers have passed the
standard corrosion tests of the appli-
cable approval agencies, the testing is
not representative of all possible cor-
rosive atmospheres. Consequently, it
is recommended that the end user be
consulted with respect to the suitability
of these coatings for any given corro-
sive environment. The effects of ambi-
ent temperature, concentration of
chemicals, and gas/chemical velocity,
should be considered, as a minimum,
along with the corrosive nature of the
chemical to which the sprinklers will be
exposed.
An intermediate level versions of the
Series TY-FRB Pendent Sprinklers are
detailed in Technical Data Sheet
TFP356, and Sprinkler Guards are de-
tailed in Technical Data Sheet TFP780
WARNINGS
The Series TY-FRB Sprinklers de-
scribed herein must be installed and
maintained in compliance with this
document, as well as with the applica-
ble standards of the National Fire Pro-
tection Association, in addition to the
standards of any other authorities hav-
ing Jurisdiction. Failure to do so may
impair the integrity of these devices.
The owner is responsible for main lain-
ing their fire protection system and de-
vices in proper operating condition.
The installing contractor or sprinkler
manufacturer should be contacted
relative to any questions.
Model/Sprinkler
Identification
Numbers
TY1131 - Upright 2.8K, 1/2"NPT
TY1231 - Pendent 28K, 1/2"NPT
TY2131 - Upright 4.2K, 1/2"NPT
TV2231 - Pendent 4.2K, 1/2"NPT
TY3131 - Upright 5.61K, 1/2"NPT
TY3231 - Pendent 5.6K, 1/2"NPT
1Y4131 - Upright 8.0k, 314"NPT
TY4231 - Pendent 8.0K, 3/4"NPT
Technical
Data
Approvals
UL and C-UL Listed.
FM, LPCB, and NYC Approved.
(Refer to Table Aforcomplete approval
information including corrosion resis-
tant status.)
Maximum Working Pressure
175 psi (12,1 bar)
Discharge Coefficient
K = 2.8 GPMIpsi1I2 (40,3 LPMIbar"2)
K = 4.2 GPM/psill2 (60,5 LPM/bar"2)
K = 5.6 GPM/psi1/2 (80,6 LPM/bar'12)
K = 8.0 GPM/psi112 (115,2 LPM/barll2)
Temperature Ratings
Refer to Table A and B
Finishes
Sprinkler: Refer to Table A and B
Recessed Escutcheon: White Coated,
Chrome Plated, or Brass Plated
Physical Characteristics
Frame ............Bronze
Button ........Brass/Copper
Sealing Assembly ..........
Beryllium Nickel w/Teflont
Bulb ..............Glass
Compression Screw .....Bronze
Deflector .......Copper/Bronze
Bushing (K=2.8) .......Bronze
4-
Page 1 of 8 APRIL, 2003 TFPI7I
ESCUTCHEON 7/16" (11,1 mm)
PLATE SEAliNG NOMINAL
SURFACE MAKE-IN
ESCUTCHEON 7116(11,1 mm)
PLATE SEATING NOMINAL
SURFACE NPT MAKE-IN
T_
2-3/16"
(55.6 mm) T
Page 2 of 0 TFPI7I
STYLE 10 or 20
RECESSED ssu ESCUTCHEON DEFLECTOR
NOMINAL
7/16"
(11.1 mm)
1iIWRENCH
MAKE-IN
2-3/16"
/ FLATS
1/2' NPT
(55.6 mm)
* I SSP DEFLECTOR * h— 2-7/8" (73,0 mm) DIA.
PENDENT RECESSED PENDENT UPRIGHT CROSS SECTION
- Frame 3- Sealing 4- Bulb 6- Deflector * Temperature rating Is indicated on deflector or adjacent to
2-Button Assembly 5-Compression 7-Bushing orifice seat on frame.
Screw **Pipe thread connections per iSO 7/1 can be provided on
special request.
FIGURE 1
QUICK RESPONSE SERIES TV-FRB UPRIGHT(rt'1131) AND PENDENT (TY1231) SPRINKLERS
2.8 K-FACTOR, 1/2 INCH NPT
STYLE 100r20
RECESSED SSUe ESCUTCHEON DEFLECTOR
I 1 7/16" ik1T'1i (11,1 mm)
11b
MAKE-IN
2.3/16"
"WRENCH
NOMINAL
(55.6 mm)
/ FLATS
112'NPT SSP DEFLECTOR* h— 2-7/8" (73.0 mm) DIA.
Fik!I
PENDENT RECESSED PENDENT UPRIGHT CROSS SECTION
1 - Frame 3- Seating 4-Bulb 6- Deflector * Temperature rating Is indicated on deflector or adjacent to
2- Button Assembly 5- Compression orifice seat on frame.
Screw --Pipe thread connections per ISO 7/1 can be provided on
special request.
FIGURE 2
QUICK RESPONSE SERIES TY-FRB UPRIGHT (TY2131) AND PENDENT (TY2231) SPRINKLERS
4.2 K-FACTOR, 1/2 INCH NPT
STYLE 30 or 40
RECESSED
ESCUTCHEON SSU *
DEFLECTOR
UPRIGHT
\r II '1tt'•'.... I
W
WRENCH
FLATS
.7/8 (73,0 mm) DIA. _J
:ESSED PENDENT
ESCUTCHEON 1/2 (12,7 mm)
PLATE SEATING ** NOMINAL
SURFACE NPT MAKE-IN
\-=
2-5/16w _____ ___________ (58,7 mm) I ______
1-9116 I (39,7 mm)
..
SSP DEFLECTOR*
PENDENT REC
LL' ;
112 I
II NI (12.7 mm) I
flFL9 '
I I__JU NOMINAL I
I I MAKE-IN
2-1/4
(57,2 mm)
3/4' NPT I
CROSS SECTION
TFPIZI Page 3 of 8
T_
2-3116
(55,6 mm) •i
STYLE 10 or 20
RECESSED su ESCUTCHEON DEFLECTOR
iv
11.1mm)
MAKE-IN
2-3/16 RENCH _ (55,6 mm)
NOMINAL
FLATS
IT I
ESCUTCHEON 7116 (11.1 mm)
PLATE SEATING ** NOMINAL
SURFACE NPT MAKE-IN
SSP DEFLECTOR * h 2-7/8'(73,0 mm) DIA.
6*
PENDENT RECESSED PENDENT UPRIGHT CROSS SECTION
- Frame 3 - Sealing 4 - Bulb 6 - Deflector Temperature rating is indicated on deflector or adjacent to
2 - Button Assembly 5- Compression orifice seat on frame. Screw Pipe thread connections per ISO 7/1 can be provided on
special request.
FIGURE 3
QUICK RESPONSE SERIES TV-FRB UPRIGHT (fl'313 1) AND PENDENT (TY3231) SPRINKLERS
56 K-FACTOR, 1/2 INCH NPT
I - Frame 3- Sealing 4 - Bulb 6- Deflector * Temperature rating is indicated on deflector or adjacent to
2 - Button Assembly 5 - Compression orifice seat on frame. Screw
**Pipe thread connections per ISO 7/1 can be provided on
special request
FIGURE 4
QUICK RESPONSE SERIES TY-FRB UPRIGHT (TY4131) AND PENDENT (TY4231) SPRINKLERS
8.0 K-FACTOR, 3/4 INCH NPT
Operation
The glass Bulb contains a fluid which
expands when exposed to heat. When
the rated temperature is reached, the
fluid expands sufficiently to shatter the
glass Bulb, allowing the sprinkler to
activate and water to flow.
Design
Criteria
The Series TY-FRB Pendent and Up-
right Sprinklers are intended for fire
protection systems designed in ac-
cordance with the standard installation
rules recognized by the applicable
Listing or Approval agency (e.g., UL
Listing is based on the requirements of
NFPA 13, and FM Approval is based
on the requirements of FM's Loss Pre-
vention Data Sheets ). Only the Style
10, 20, 30, or 40 Recessed Escutch-
eon, as applicable, is to be used for
recessed pendent installations.
Pae4of8 -
SPRINKLER FINISH (See Note 7)
K TYPE TEMP. BULB• NATURAL CHROME
LIQUID BRASS PLATED 1POLYESTER
135°F/570C Orange
PENDENT
(TY1231)
and
1.2,3.5 1551:/68CC Red
1751:179°C Yellow
UPRIGHT 2001:/93°C Green
2.8 (TYII3I) 286°F/141°C Blue
1/2°
NPT 135°F/57°C Orange
RECESSED
PENDENT 155°F/68°C Red
175°F/79°C Yellow (1Y2231)°
200°17193°C Green Figure 5 1.2, 5
138CF157°C Orange
RECESSED
PENDENT 155°F/68°C Red
175°Fl79*C Yellow CY2231
200°F/93°C Green Figure 6
1 35°F/57°C Orange
PENDENT
(TY2231)
and
155°F168°C Red
175°F179°C Yellow
UPRIGHT 200°F/930C Green
4.2
1/2.
NPT
(TY3131)
1,2 286°F/141°C Blue
135°F/57°C Orange
RECESSED
PENDENT 155°F/680C Red
175°F179°C Yellow (TY2231)'
2007F/93°C Green Figure 7
1351:157°C Orange
RECESSED
PENDENT 155°F/680C Red
175°F179°C Yellow (TY2231)°°
200°F1930C Green Figure 8
NOTES: Listed by Underwriters Laboratories, Inc. (UL) as Quick Response Sprinklers.
Listed by Underwriters Laboratories, Inc. for use In Canada (C-UL) as Quick Response
Sprinklers. Approved by Factory Mutual Research Corporation (FM) as Quick Response Sprin-
klers. 5. Approved by the City of New York under MEA 354-01-E.
7. Where Polyester Coated Sprinklers are noted to be UL and C-UL Listed, the sprin-
klers are UL and C-UL Listed as Corrosion Resistant Sprinklers.
Installed with Style 10(1/2° NPT) or Style 40 (3/4° NPT) 3/4° Total Adjustment Re-
cessed Escutcheon, as applicable. Installed with Style 20(1/2° NPT) or Style 30 (3/4° NPT) 112° Total Adjustment Re-
cessed Escutcheon, as applicable. Frame and Deflector only. Listings and approvals apply to all colors (Special Order).
N/A: Not Available
TABLE A
LABORATORY LISTINGS AND APPROVALS
2.8 AND 4.2 K-FACTOR SPRINKLERS
TFPI7I
Installation
The Series TY-FRB Sprinklers must be
installed in accordance with the follow-
ing instructions:
NOTES
Do not install any bulb type sprinkler If
the bulb Is cracked or there is a loss of
liquid from the bulb. With the sprinkler
held horizontally, a small air bubble
should be present. The diameterof the
air bubble is approximately 1/16 inch
(1,6 mm) for the '135°F/570C to 3/32
inch (2,4 mm) for the 2860F/1410C
temperature ratings.
A leak tight 1/2 inch NPTsprinkler joint
should be obtained with a torque of 7
to 14 ft.Ibs. (9,5 to 19,0 Nm). A maxi-
mum of 21 ft. tbs. (28,5 Nm) of torque
may be used to install sprinklers with
1/2 NPT connections. A leak tight 3/4
inch NPT sprinkler joint should be ob-
tained with a torque of 10 to 20 lt.lbs.
(13,4 to 26,8 Nm). A maximum of 30
ft.lbs. (40,7 Nm) of torque is to be used
to install sprinklers with 3/4 NPT con-
nections. Higher levels of torque may
distort the sprinkler inlet and cause
leakage or impairment of the sprinkler.
..Do not attempl.;to make-up for insuffi-
cient adjustment in the escutcheon
..:plate by-under--or over-tightening the
sprinkler. Readjust the position of the
sprinkler fitting to suit.
The SeriesTY-FRB Pendent and Up-
right Sprinklers must be installed in
accordance with the following instruc-
tions.
Step 1. Pendent sprinklers are to be
installed in the pendent position, and
upright sprinklers are to be installed in
the upright position.
Step 2. With pipe thread sealant ap-
plied to the pipe threads, hand tighten
the sprinkler into the sprinkler fitting.
Step 3. Tighten the sprinkler into the
sprinkler fitting using only the W-Type
6 Sprinkler Wrench (Ref. Figure 13).
With reference to Figures 1. 2, 3, and
4, the W-Type 6 Sprinkler Wrench is to
be applied to the sprinkler wrench
flats.
The Series TY-FRB Recessed Pen-
dent Sprinklers must be installed in
accordance with the following instruc-
tions.
Step A. After installing the Style 10.
20. 30. or 40 Mounting Plate, as appli-
cable, over the sprinkler threads and
with pipe thread sealant applied to the
pipe threads, hand tighten the sprin-
kler into the sprinkler fitting.
Step B. Tighten the sprinkler into the
TFPI7I Page 5 of 8
SPRINKLER FINISH (See Note 7)
K TYPE TEMP. BULB
LIQUID
NATURAL
BRASS
I CHROME
J PLATED
WHITE
JPOLYESTER
LEAD
COATED
-
5.6
PENDENT
(TY3231)
and
UPRIGHT
(TY3131)
135°F/57°C Orange
1.2.3.45,6 1,2,3,5 155°F/68°C Red
1750F1790C Yellow
200°F/93°C Green
286°F/1410C Blue
1/2
NPT 135°F/570C Orange
1.2,4,5
Green
N/A
RECESSED
PENDENT
(TY3231)
Figure 9
155°FI68*C Red
175°F179°C Yellow
200°F/93C
• 1351F/5rC Orange I I I
1,2,3,4,5 I I 1,2,4,5
Green
N/A
RECESSED
PENDENT
(TY3231)
Figure 10
155°F/68C Red
175F/79°C Yellow
200°F193°C
8.0
PENDENT
(TV4231)
and
UPRIGHT
(Y4131)
135F/57°C Orange
1, 2, 3,4,5,6
1.2.5 1550F/680C Red
175°FI79C Yellow
200°F/93°C Green
286°F/1410C Blue
3/4.
NPT 135F/57°C Green
1,2,4,5 N/A
RECESSED
PENDENT
(TY4231)
Figure 11
155F/68C Orange
175F/79°C Red
200F/93°C Yellow
1354F1570C Orange
1, 2, 3, 4,5
Green
N/A
RECESSED
PENDENT
(TY4231)
Figure 12
155°F/680C Red
175°FI79C Yellow
200°F/93°C
NOTES:
Listed by Underwriters Laboratories, Inc. (UL) as Quick Response Sprinklers.
Listed by Underwriters Laboratories, Inc. for use in Canada (C-UL) as Quick Response Sprinklers.
Approved by Factory Mutual Research Corporation (FM) as Quick Response Sprinklers.
Approved by the Loss Prevention Certification Board (LPCB) as Quick Response Sprinklers; however, the LPC does not rate the thermal
sensitivity of recessed sprinklers.
S. Approved by the City of New York under MEA 354-01-E.
VdS Approved (For details contact Tyco Fire & Building Products, Enschede, Netherlands, Tel. 31-53-428-4444/Fax 31-53-428-3377).
Where Polyester Coated and Lead Coated Sprinklers are noted to be UL and C-UL Listed, the sprinklers are UL and C-UL Listed as
Corrosion Resistant Sprinklers. Where Lead Coated Sprinklers are noted to be FM Approved, the sprinklers are FM Approved as a
Corrosion Resistant Sprinklers.
Installed with Style 10(1/2' NPT) or Style 40(3/4' NPT) 3/4' Total Adjustment Recessed Escutcheon, as applicable.
"Installed with Style 20 (1/2' NPT) or Style 30 (3/4' NPT) 1/2' Total Adjustment Recessed Escutcheon, as applicable.
Frame and Deflector only. Listings and approvals apply to all colors (Special Order).
N/k Not Available
TABLE B
LABORATORY LISTINGS AND APPROVALS
5.6 AND ao K-FACTOR SPRINKLERS
sprinkler fitting using only the W-Type
7 Recessed Sprinkler Wrench (Ref.
Figure 14). With reference to Figure 1,
2, 3, and 4, the W-Type 7 Recessed
Sprinkler Wrench Is to be applied to
the sprinkler wrench flats.
Step C. After the ceiling has been in-
stalled or the finish coat has been ap-
plied, slide on the Style 10, 20, 30, or
40 Closure over the Series TV-FRB
Sprinkler and push the Closure over
the Mounting Plate until its flange
comes in contact with the ceiling.
Pae6of8 -. TFPI7I
2-7/8' DIA. -
(73.0 314' (19,1 inn) 5/8±1/4'
06-M-4 MM) 2-1/4' OIA. 1/4' (6,4 mm) I
FACE OF mi MOUNTING I SPRINKLER PLATE
I
FITTING
1/8' I ____
MOUNTING
SURFACE
1-5/16' (33.3 Mai) CLOSURE SERIES
TY-FRB 13/16' (20,6 mm)
FIGURE 5
SERIES 1Y-FRB RECESSED PENDENT
WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT
STYLE 10 RECESSED ESCUTCHEON
2.8 K-FACTOR, 1/2 INCH NPT
- 2-7/8' DIA.
518±114' (73,0 mm) I 3/4'(19.1 mm)
- (15,9±6.4 mm) 2-1/4' DIA. 1/4'(6,4 mm) I
FACE OF MOUNTING I (57
PLATE I SPRINKLER
FTTING
1/8]
MOUNTING
SURFACE
SERIES 1-1/4' (31.8 mm) I CLOSURE TYFRB 314'(19,1 mm)
FIGURE 7
SERIES 7Y-FRB RECESSED PENDENT
WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT
STYLE 10 RECESSED ESCUTCHEON
4.2 K-FACTOR, 1/2 INCH NPT
- 2-7/8' DIA. -
(73,0 mm) 1/2±1/8' 1/2'(12,7 mm)
1 (12,7*3,2 mm) 2-1/4' DIA. 1/4' (6.4 MM) I
I PLATE
FACE OF
r-57'2
MOUNtiNG
SPRINKLER
FITTING
1/8'
AN I
MOUNTIN
7 1~E_
(3.2 mm)
t \
SURFACE
CLOSURE SERIES 1-5116' (33,3
TYFRB 1-1/16' (27,0 mm)
FIGURE 6
SERIES TY-FRB RECESSED PENDENT
WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT
STYLE 20 RECESSED ESCUTCHEON
2.8 K-FACTOR, 1/2 INCH NPT
- 2-7/8' DIA. -
(73,0 mm) 1/2±1/8' 1/2(12,7mm) r (12,7±3,2 mm) - 2-1/4' DIA. 114' (6,4 mm) I
MOUNTING I 1 FACE OF (572mm)
PLATE I I SPRINKLER I FITTING
/ _____ _______
1/a'
d ________________
I \
MOUNTING
SURFACE
SERIES 1-1/4'(31.8 mm) CLOSURE TY.FRB V (25,4 mm)
FIGURE 8
SERIES 7Y-FRB RECESSED PENDENT
WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT
STYLE 20 RECESSED ESCUTCHEON
4.2 K-FACTOR, 1/2 INCH NPT
Care and
Maintenance
The Series TY-FRB Sprinklers must be
maintained and serviced in accord-
ance with the following instructions:
NOTES
Before closing a fire protection system
main control valve for maintenance
work on the tire protection system that
it controls, permission to shutdown the
affected fire protection system must be
obtained from the proper authorities
and all personnel who may be affected
by. this action must be notified.
Absence of an escutcheon, which is
used to cover a clearance hole, may
delay the time to sprinkler operation in
a fire situation.
Sprinklers that are found to be leaking
or exhibiting visible signs of corrosion
must be replaced.
Automatic sprinklers must never be
painted, plated, coated or otherwise
altered after leaving the factory. Modi-
fied sprinklers must be replaced.
Sprinklers that have been exposed to
corrosive products of combustion, but
have not operated, should be replaced
if they cannot be completely cleaned
by wiping the sprinkler with a cloth or
by brushing it with a soft bristle brush.
Care must be exercised to avoid dam-
age to the sprinklers - before, during,
and after installation. Sprinklers dam-
aged by dropping, striking, wrench
twist/slippage, or the like, must be re-
placed. Also, replace any sprinkler that
has a cracked bulb or that has lost
liquid from its bulb. (Ref. Installation
Section).
Frequent visual inspections are rec-
ommended to be Initially performed for
corrosion resistant coated sprinklers,
after the installation has been com-
pleted, to verify the integrity of the cor-
rosion resistant coating. Thereafter,
annual inspections per NFPA 25
should suffice; however, instead of in-
specting from the floor level, a random
sampling of close-up visual inspec-
tions should be made, so as to better
determine the exact sprinkler condi-
TFPI7I-
- 2-7/8' DIA. -
5 (73.0 mm) 3/4' (19.1 mm) - (15,9±6,4 mm) 2-1/4' DIA. 1/4' (6,4 mm) I
SPRINKLER PLATE I
FACE OF
2mm)
-1 MOUNTING I
FFI11NG
1/8'
L. T'
MOUNTING
fj
SURFACE
CLOSURE SERIES 1-1/4' (31,8mm
TY-FRB 314' (19.1 mm)
FIGURE 9
SERIES TY-FRB RECESSED PENDENT
WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT
STYLE 10 RECESSED ESCUTCHEON
5.6 K-FACTOR, 1/2 INCH NPT
- 2.7/8' DIA. -
5/8±1/4' (73.0 mm) 3/4'(19,1 mm)
r (15,9±6,4 mm) 2-1/4' DIA. 1/4'(6.4 mm)
MOUNTING I 1 FACE OF (57.2
I SPRINKLER PLATE I
I FITTING
_____ I I / ____ __ ______________ (3.2 mm)
/_
I
_
'MOUNTING
SURFACE
CLOSURE SERIES 1-5/16':!: (33.34MMI
TY-FRB 13/16' (20.6 mm)
FIGURE 11
SERIES TY-FRB RECESSED PENDENT
WITH 7W0-PIECE 3/4 INCH TOTAL ADJUSTMENT
STYLE 40 RECESSED ESCUTCHEON
8.0 K-FACTOR, 3/4 INCH NPT
-.
Page 7 of 8
- 2-718' 01k -
(73.0 mm) 1/2±1/8' 112' (12.7 mm) r (12,7*39 mm) 2-1/4' 01k 1/4' (6,4 MM) I FACE OF MOUNTING I SPRINKLEA PLATE
FITTING
118'
SURFACE
,
,///
t
T__\_ MOUNTING
SERIES 1-1/4'(31.8 mm) CLOSURE TY.FRB 1' (25,4 mm)
FIGURE 10
SERIES TY-FRB RECESSED PENDENT
WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT
STYLE 20 RECESSED ESCUTCHEON
5.6 K-FACTOR, 1/2 INCH NPT
- 2-7/8 01k
(73,0 mm) I 1!2* (12.7 mm)
1 (12,7*3,2mm) - 2-1/4' 01k 1/4 (6,4 mm)
FACE OF
I
(57,2 mm) •J j MOUNTING I I SPRINKLER PLATE I FITTING
(3.2 mm)
LJ I \
MOUNTING
SURFACE
CLOSURE SERIES 1-5/16'(33.3 mm
TYFRB 1-1/16' (27,0 mm)
FIGURE 12
SERIES TV-FRB RECESSED PENDENT
WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT
STYLE 30 RECESSED ESCUTCHEON
8.0 K-FACTOR, 3/4 INCH NPT
tion and the long term integrity of the
corrosion resistant coating, as it may
be affected by the corrosive conditions
present.
The owner is responsible for the in-
spection, testing, and maintenance of
their fire protection system and de-
vices in compliance with this docu-
ment, as well as with the applicable
standards of the National Are Protec-
tion Association (e.g., NFPA 25). in
addition to the standards of any other
authorities having jurisdiction. The in-
stalling contractor or sprinkler manu-
facturer should be contacted relative to
any questions.
It is recommended that automatic
sprinkler systems be inspected,
tested, and maintained by a qualified
Inspection Service.
WRENCH RECESS
(END 'A USED FOR
1/2' NPT MODELS)
WRENCH RECESS
(END 'B' USED FOR
3/4' NPT MODELS)
FIGURE 13
W-TYPE 6 SPRINKLER
WRENCH
WRENCH
RECESS
PUSH WRENCH
INTO ENSURE
ENGAGEMENT
WITH SPRINKLER
WRENCHING AREA
FIGURE 14
W-TYPE 7 RECESSED
SPRINKLER WRENCH
Pae8of8 TFPI 71
P/N 57 - XXX - X - XXX
I L
330 28K UPRIGHT (1/2"NPT) TY1I31
331 2.8K PENDENT (1/2'NPl) TY1231
340 4.2K UPRIGHT (112'NPl) 1Y2 131
341 4.2K PENDENT (1t2'NPT) 1Y2231
370 5.6K UPRIGHT (1/2'NPT) TY3131
371 5.6K PENDENT (112'NPT) Ti3231
390 8.0K UPRIGHT (3/4'NPl) 1Y4131
391 8.0K PENDENT (314'NPT) TY4231
I
I
L ____
SPRINKLER I ..L..
135
155
175
200
286
RATING
I NATURAL BRASS 155°F/680C
4 WHITE POLYESTER 175°F179°C
9 CHROME PLATED 2000F/93°C
7 LEAD COATED 286F/141°C
TABLE C
PART NUMBER SELECTION
SERIES TY-FRB PENDENT AND UPRIGHT SPRINKLERS
Limited
Warranty
Products manufactured by Tyco Fire
Products are warranted solely to the
original Buyer for ten (10) years
against defects in material and work-
manship when paid for and properly
installed and maintained under normal
use and service. This warranty will ex-
pire ten (10) years from date of ship-
ment by Tyco Fire Products. No war-
ranty is given for products or
components manufactured by compa-
nies not affiliated by ownership with
Tyco Fire Products or for products and
components which have been subject
to misuse, improper installation, corro-
sion, or which have not been Installed,
maintained, modified or repaired in ac-
cordance with applicable Standards of
the National Fire Protection Associa-
tion, and/or the standards of any other
Authorities Having Jurisdiction. Mate-
rials found by Tyco Are Products to be
defective shall be either repaired or
replaced, at Tyco Fire Products' sole
option. Tyco Fire Products neither as-
sumes, nor authorizes any person to
assume for it, any other obligation in
connection with the sale of products or
parts of products. Tyco Fire Products
shall not be responsible for sprinkler
system design errors or inaccurate or
incomplete information supplied by
Buyer or Buyer's representatives.
IN NO EVENT SHALL TYCO FIRE
PRODUCTS BE LIABLE, IN CON-
TRACT, TORT, STRICT LIABILITY OR
UNDER ANY OTHER LEGAL THE-
ORY, FOR INCIDENTAL, INDIRECT,
SPECIAL OR CONSEQUENTIAL
DAMAGES, INCLUDING BUT NOT
LIMITED TO LABOR CHARGES, RE-
GARDLESS OF WHETHER TYCO
FIRE PRODUCTS WAS INFORMED
ABOUT THE POSSIBILITY OF SUCH
DAMAGES, AND IN NO EVENT
SHALL TYCO FIRE PRODUCTS' LI-
ABILITY EXCEED AN AMOUNT
EQUAL TO THE SALES PRICE.
THE FOREGOING WARRANTY IS
MADE IN LIEU OF ANY AND ALL
OTHER WARRANTIES EXPRESS OR
IMPLIED. INCLUDING WARRANTIES
OF MERCHANTABILITY AND FIT-
NESS FOR A PARTICULAR PUR-
POSE
Ordering
Procedure
When placing an order, indicate the full
product name. Refer to the Price List
for complete listing of Part Numbers.
Contact your local distributor for avail-
ability.
Sprinkler Assemblies with NPT
Thread Connections:
Specify: (Specify Model/SIN), Quick
Response, (specify K-factor), (specify
temperature rating), Series TY-FRB
(specify Pendent or Upright) Sprinkler
with (specify type of finish or coating),
P/N (specify from Table C).
Recessed Escutcheon:
Specify: Style (specify) Recessed Es-
cutcheon with (specify finish), P/N
(specify).
1/2' (15 mm) Style 10
Chrome Plated .........P/N 56-701-9-010
1/2' (15 mm)
Style 10
White Color
Coated ................. PIN 56-7014-010
1/2' (15 mm)
Style 10
Brass Plated ...........P/N 56-701-2-010
1/2' (15 mm)
Style 20 Chrome Plated .........P/N 56-705-9-010
112 (15 mm) Style 20
White Color
Coated................PIN 56-705-4-010
1/2' (15 mm)
Style 20
Brass Plated ...........P/N 56-705-2-010 3/4' (20 mm)
Style 30
Chrome Plated .........PIN 56-705-9-011
3/4' (20 mm) Style 30
White Color Coated ................ P/N 56-7054-011
3/4' (20 mm)
Style 30 Brass Plated ...........P/N 56-705-2-011
3/4' (20 mm)
Style 40
Chrome Plated .........PIN 56-700-9-010
3/4' (20 mm)
Style 40
White Color
Coated................P/N 56-700-4-010 3/4' (20 mm)
Style 40
Brass Plated ...........P/N 56-700-2-010
Sprinkler Wrench:
Specify: W-Type 6 Sprinkler Wrench,
P/N 56-000-6-387.
Specify: W-Type 7 Sprinkler Wrench,
P/N 56-850-4-001.
TYCO ARE PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446