The URL can be used to link to this page

Home My WebLink About163 ACACIA AVE; ; FPR2019-01424btyof PERMIT REPORT Carlsbad Print Date: 07/31/2024 Permit No: FPR2019-0142 Job Address: 163 ACACIA AVE, CARLSBAD, CA 92008-3202 Status: Closed - Finaled Permit Type: FIRE-Construction Residential Work Class: Multifamily Fire Alarm Parcel #: 2042311800 Track U: Applied: 06/04/2019 Valuation: $0.00 Lot #: Issued: 06/24/2019 Occupancy Group: Project U: Finaled Close Out: 07/31/2024 #of Dwelling Units: Plan U: Bedrooms: Construction Type: Final Inspection: Bathrooms: Orig. Plan Check U: INSPECTOR: Fieri, Dominic Plan Check U: Project Title: Description: ACACIA AV ESTATES -NEW SPRINKLER MONITORING SYSTEM WITH NEW ANNUNCIATED FIRE ALARM Applicant: FPContractor: HCl SYSTEMS INC HCI SYSTEMS INC JEFF RODGERS 4585 MURPHY CANYON RD 4585 MURPHY CANYON RD SAN DIEGO, CA 92123-4318 SAN DIEGO, CA 92123-4318 (909) 628-7773 (858) 560-7000 FEE AMOUNT FIRE Sprinkler Monitoring $383.00 Total Fees: $383.00 Total Payments To Date: $383.00 Balance Due: $0.00 Fire Department Page 1 of 1 1635 Faraday Avenue, Carlsbad CA 92008-7314 1 442-339-2665 1 Inspections: 442-339-2660 1 www.carlsbadca.gov CITY OF CARLSBAD POST INCONSPICUOUS PtACE 1635 Faraday Ave. Carlsbad CA 92008 INIS*ESS Re=MAWNcEATWICATE lb.p.,a*i,i c,twaCn lwn.d bsNw I wwa II a'a. pj* io Wa CsatXwa.*ncn Mfs9 N*Pads&Pn,alfl a.otW. *ØK Iw, Thi dUIW.zasSW Wa kaaa. a aA.a NWWW aaWNaIafb* Wa.IaINm NA4CS DESCRJPT!ON Electrical Contractors BUSINESS LOCATION 1354 S PARKSIDE PL EXPIRATION DATE 07/3112019 I NOT TRANSFERABLE UC. NUMBER BLOS1 235322 DATEMSM0 05/21/2018 NA= CODE 238210 OWER FIRMO CORPORATION NAME BUSINESS NAME MMU$O ADORESS C1TY AND STATE HCI SYSTEMS INC HCI SYSTEMS INC 1354 S PARKSIDE PL ONTARIO, CA 91761-4555 (,Cityof Carlsbad KEEP FOR YOUR RECORDS UCENSE NUMBER BL0S1235322 DATE ISSUED 05/21/2018 EXPIRATION DATE 07131/2019 BUSINESS NAME HCI SYSTEMS INC BUSINESS LOCATION 1354 S PARKSIDE PL TAXES AW W*AXXXVXNM VtKOJY GUSOJESS tM OFONVACC CITY OF CARLSBAD IJCI Systems Inc. FIRE / LIFE SAFETY & LOW VOLTAGE SPECIALISTS California Contractor's License # 905493 Fire Alarm System Complete Material Submittal Prepared for: ACACIA AVE. ESTATES 163 ACACIA AVENUE, CARLSBAD, CA 92008 FPR20I9-0142 163 ACACIA AVE ACACIA AV ESTATES - NEW SPRINKLER MONITORING SYSTEM VMTH NEW ANNUNCIATED FIRE ALARM 2042311800 6/412019 fPR20I9-0142 Ontario • San Diego • Irvine • Hayward • Burbank • Fresno • Sacramento Corporate Office: 1354 South Parkside Place, Ontario, CA 91761 Phone: (909) 628-7773 FAX: (909) 628-7774 24-Hour Service: (877) 331-2084 Website: www.hcisystems.net ACACIA AVE. ESTATES 163 ACACIA AVENUE, CARLSBAD, CA 92008 Manufacturer Device Model # Description C.S.F.M. # EDWARDS 1064 Fire Alarm Control Panel 7300-1657:0244 SPACE AGE ACE-1 1 Fire Alarm Document. Cabinet 7300-0553:0110 DSC LE4010CF Fire Alarm Cellular Alarm Communicator 7300-1273:0505 DSC RM-2 EOL Relay Module 7300-1273:0127 EDWARDS SIGA-PD Photoelectric Smoke Detector 7272-1657:0331 EDWARDS SIGA-278 Manual Pull Station 7150-1657:0129 EDWARDS SIGA-02 Dual Input Module 7300-1657:0121 EDWARDS 439D-1OAW-R Water Flow Sprinkler Bell 7136-1657:0150 EDWARDS Catalog D Small Building Fire alarm Solutions LIFE SAFETY INCIDENT MANAGEMENT Intelligent Fire Alarm Systems =064~ 101000 FDNY COA 6227 * 7165-1657: 0244 Overview EDWARDS brand intelligent life safety systems offer the power of high-end intelligent processing in configurations that deliver uncomplicated solutions for small to mid-sized applications. With intelligent detection, electronic addressing, automatic device mapping, optional Ethernet® connectivity, and a full line of easily- configured option cards and modules, these flexible systems offer versatility that benefits building owners and contractors alike. The 1064 provides one Class B intelligent device loop that sup- ports up to 64 device addresses, and two Class B Notification Ap- pliance Circuits (NACs). Optional Class A device wiring is available with the use of a module. The 101000 provides one Class A or Class B intelligent device loop that supports up to 250 device addresses. Loop controller modules may be added in combination to expand total system capacity in 250-point increments to up to 1,000 device addresses. The iOl 000 panel includes four NACs that may be wired for either Class A or Class B operation. The RZI16-2 module adds even more capacity to iO installations by adding up to 16 conventional device circuits and two additional notification appliance circuits. This makes them an ideal retrofit solution that can accommodate new intelligent detectors, as well as existing conventional devices. iO Series supports a wide range of high-end features, including: Signature Series intelligent modules, detectors, and bases R-Series remote annunciators SIGA-REL Releasing Modules Fully integrated CO detection using Signature Series detec- tors with or without audible signaling Features Auto-programming speeds installation time Supports Signature Series intelligent modules and detectors Combines the Signature intelligent releasing module with Signature multisensor detectors for reliable fire suppression Form C contacts for alarm and trouble, Form A for supervisory Electronic addressing with automatic device mapping Optional Ethernet port for diagnostics, programming and a variety of system reports Two programmable switches with LEDs and custom labeling Supports Genesis horn silence over two wires, and UL 1971-compliant strobe synchronization Class B or Class A wiring Ground fault detection by module Supports up to eight serial annunciators, (LCD, LED-only, and graphic interface) Can use existing wiring for most retrofit applications Upload/download remotely or locally Two-level maintenance alert reporting Pre-alarm and alarm verification by point Adjustable detector sensitivity 4 x 20 character backlit LCD display Optional earthquake hardening: seismic Importance Factor 1.5 Standalone operation Transmission test frequency by hour Page 1 of 8 DATA SHEET E85001-0135 Not to be used for installation purposes. Issue 1 Application EDWARDS i0 Series life safety systems are powerful intelligent solu- tions for small to mid-sized buildings. Advanced intelligent technol- ogy delivers the benefits of flexible system installation, while clean and easy-to-operate user interfaces make panel operation and system maintenance quick and intuitive. The smart choice Signature Series electronic addressing eliminates the tedium of setting dipswitches, and automatic device mapping ensures that each device resides on the system at its correct location. Mean- while, innovative programming allows the designer to customize the system to precisely suit the needs of the building owner. Reliability you can count on The inherent fault-tolerant characteristics of Analog/Addressable Technology boosts the reliability of EDWARDS fire alarm systems. When combined with i0 Series smoke and heat detectors, these systems deliver a level of dependability not previously available for small to mid-sized applications. All EDWARDS systems are built to exacting reliability benchmarks and meet international standards for quality, in addition to agency listings for dependability. Clear-cut remote annunciation Remote annunciation is a strong suit of the iO Series fire alarm systems. Up to eight annunciators can be installed on a single system. Compatible annunciators include a range of. LED and LCD models that provide zone or point annunciation, as well as com- mon control capabilities. i0 control panels also supports graphic annunciation with optional RA Graphic Annunciator interface mod- ules. Each interface provides common control and 32 LEDs. Programming and remote diagnostics EDWARDS iO Series life safety systems are simple to set up, yet offer advanced programming features that put these small building panels into a class of their own. The auto programming feature quickly gets the panel operational using factory default settings. Basic zone and point settings can be programmed through the front panel interface, so the system is up and running in no time. For more advanced system configuration and correlation groups programming, i0 Series systems interface to a PC running com- patible 10-CU software. This option offers full system configuration in the familiar Windows® operating environment. Connection is made to a laptop through the panel's optional RS-232 communi- cations port, which can also be used to connect a system printer. Among the many innovative features of i0 Series control panels is the optional network card. This module provides a standard 10/100 Base T Ethernet® network connection that permits access to the control panel from any remote location with the correct communications protocols. The connection can be used to download to the panel from the i0-CU, or upload and view system reports using the i0-CU. Available system reports include: Correlation groups Device details Device maintenance History Internal status System configuration System status Walk test Dialer CO runtime Flexibility built right in Two fully-programmable front panel switch/LED combinations pro- vide an added measure of flexibility. Their slide-in labels take the mystery out of custom applications, and present a clean finished appearance. Perfect for retrofits EDWARDS i0 Series control panels are particularly well-suited to retrofit applications. All connections are made over standard wiring - no shielded cable required. This means that in most situations existing wiring can be used to upgrade a legacy control panel to 10 technology without the expense or disruption of rewiring the en- tire building. 10 control panels also support the ingenious RZl16-2 Zone Module, which adds up to 16 conventional circuits and two NACs. This combination easily accommodates new intelligent detection alongside existing conventional circuits, making It an superior solution in the retrofit market. Signals with a difference i0 system NACs are configurable to fully support the advanced signaling technology of EDWARDS Genesis and Enhanced Integ- rity notification appliances. These devices offer precision synchro- nization of strobes to UL 1971 standards. For Genesis devices, enabling this feature allows horns to be silenced while strobes on the same two-wire circuit continue to flash until the panel is reset. A complete line of accessories 10 Series life safety systems are supported by a complete line of analog/addressable detectors, modules and related equipment. Consult the Ordering Information section for details. Dimensions (2) (3) (4) To 0 0 o 0 0 o o 04 08 10 0 81 • 81 81 D9bl 09P Surface Mounting Holes (3) Backbox with Door Attached Semi-flush mounting Holes (4) Backbox with door and him kit attached. Panel dimensions, in (cm) Model 01 02 03 I 04 I 05 I 06 I 07 I 08 I D9 01000 28.0 I 3.85 I 9.0 22.0 I 15.75 I 10.25 I 4.4 I 28.2 2.7 (71.1) I (9.8) I (22.8) I (55.8) I (40.0) I (26.0) I 111.11 I (71.6) I (6.8) i064 21.5 I 3,85 7.5 I 15.5 14.25 I 10.25 I 4.5 21.7 2.7 (54.6) (9.8) (19.0) (39.4) (36.2) (26.0) (11.4) * Add 1-1/2 in, (3.81 cm) to Dl and D5 dimensions for trim kit. The trim kit provides 0.75 inches (1.9 cm) of (rim to the top, bottom, and sides of the backbox. Page 2 of 8 DATA SHEET E85001-0135 Not to be used for installation purposes. Issue I System Layout 101000 Any combination of two single- or dual Signature loop modules - Standard Loop 250 points (one expansion slot) 0 SDC2 Expander, Loop ilo_M 250 points YR 9'!P!' °'? ------------------------------, (one expansion slot) iO-SDC1 Expander Loop: 250 points (one expansion slot) 10-SDC2 Expander, Loop 2 of 2: 250 points - 1- - ----------- t Ethernet (SA-ETH) DAC17Dialer (SA-DACT) RS-232 (SA-232) Sixteen Conventional lDCs, Relays: Two Form C, one Form A two additional NACs with RZ116-2 module Each i01000 panel has room for up to two Signature loop control- ler modules in any combination of single or dual 250-device loops. r i01000 loops support 125 detectors and 125 modules. Panel Layout 1064 JIiIL_ Loop supports up to 64 intelligent devices of any type. Up to 20,000 feet of wiring. 1 ! Two Class B or two optional Class A NACs Optional 10 A or 6.5 A Booster Power Supply Relays: Two Form C, one Form A Each 1064 panel ships with one Signature loop controller that sup- ports 64 devices of any type. This panel's device capacity cannot be expanded. 1 Transformer 2 Main AC wiring block & fuse holder 3 RS-232 card connector (J3) 4 Dialer card connection (J8) 5 Ethernet card connector (Ji) 6 Main circuit board 7 Panel backbox enclosure 8 Operator interface 9 SLC card connector (J7) 10 Class A card connector (J2) 11 Tie wrap mounts 12 LED expander connector (J6) 13 Standby batteries Page 3 of 8 DATA SHEET E85001-0135 Not to be used for installation purposes. Issue 1 Wiring & Configuration Signature device loop The system provides one Signature device loop circuit with a total capacity of 125 detectors and 125 module addresses. The loop circuit is supervised for opens, shorts, and grounds. Circuit specifications 101000 i064 Device loops One Class B or A One Class B or A loop, loop, supporting 125 supporting 64 devices of detectors and 125 any kind. modules. Expandable to four loops. Communication Maximum 20 V peak-to-peak line voltage Circuit current 0.5 A max Circuit 660 total, 0.5 pF, max impedance Isolators 64 maximum Signal Supported on a system-wide basis (all device loops) Synchronization when using a SlGA-CC1S or SlGA-MCC1 S module and Genesis or Enhanced Integrity notification ap- pliances. Class B sorring Class A wiring SLC A; LOOP Leep LOOP Loop Loop card device device Loop card oaia Line dovica device Notification appliance circuits (TB2) iOl 000 control panels come equipped with four notification ap- pliance circuits. i064 control panels come with two NACs. Each circuit can be individually configured for continuous, temporal, synchronized, and coded output. Specifications 101000 1064 Circuit Type 4 Class B or 2 Class A 2 Class B or 2 Class A with SA-CLA module Voltage 24 VFWR Current 6.0 A total, 2.5 A max. 3.75 A total, 2.5 A max. per circuit at 120/230 per circuit at 120/230 VAC 60 Hz. VAC 60 Hz. 5.0 A total, 2.5 A max. 3.0 A total, 2.5 A max. per circuit at 230 VAC per circuit at 230 VAC 50 Hz. 50 Hz. Impedance 26 0 total, 0.35 hF max EOLR 15K0,112W Synchronization Supported system-wide Auxiliary & smoke power outputs (TB3) The control panel provides two auxiliary power TB3 outputs that can be used for powering ancillary 0 equipment such as remote annunciators and two (1) ® NO wire smoke detectors. Aux 2 can be software NC selected to operate continuously. The circuit is 0 supervised for shorts and grounds. (7 (2) Circuit specifications Circuit voltage 21.9 to 28.3 V range Resettable circuit 24 VDC nominal at 500 mA (Aux power 2) Continuous circuit 24 VDC nominal at 500 mA. (Aux power 1) Use this circuit for powering two-wire smoke detectors. Note: Any current above 0.5 amp connected to both Aux 1 and 2 will reduce the total available NAG power by that amount. (1) Trouble Alarm, trouble, and supervisory relay (TB3) (2) Supervisory The trouble relay is normally-open, held closed, (3) Alarm and opens on any trouble event or when the panel is de-energized. The supervisory relay is (4) Smoke/Aux normally open, and closes on any supervisory event. The alarm relay changes over on any alarm event. Relay specifications Alarm Trouble Supervisory Type Form C Form A Voltage 24 VDC at 1 A resistive 24 VDC at 1 A resistive Relay circuits can only be connected to power-limited sources. Annunciator loop (TB4) The control panel provides a connection for up to eight serially driven and supervised remote annunciators. Circuit specifications Device loops Class B (Style ') or Class A (Style Z) Circuit voltage 2.55 V Circuit current 30 mA max Circuit Up to 8 annunciators or 4000 feet impedance Class B Class Channel 1 Channel 2 Channel 1 Channel 2 +—+— ______ lllllTB4 NO NC NO Class B wiring doss A wiring OLR OLR CH2 IN I [_JcH2(~)lN CH2 (-I IN I CH2 (.) IN Marking indicates output signal polarity when the circuit is active. Polarity reverses when the circuit is not active. Wire notification appliances accordingly. Notification appliance polarity shown in active state. Page 4of8 DATA SHEET E850010135 Not to be used for installation purposes. Issue 1 tflemet cara Option Cards EDWARDS iO Series panels are supported by a complete line of modules and related equipment that enhance performance and extend system capabilities. Option cards plug directly into the control panel main circuit board or are connected to it with a ribbon cable. After installation, terminals remain accessible. The cabinet provides ample room for wire routing, keeping wiring neat at all times. Single and Dual Loop Controller Cards The iO-SDC1 is a single loop controller card that can be used with the i064 as a replacement for the standard 64-point loop, or with the i01000 as a 250-point expansion module. The iO-SDC2 is a 500-point dual loop controller card for the iO1 000 that provides two SLC circuits, each with 125 detector addresses and 125 module addresses. Specifications iO-SDC1 iO-SDC2 Device Addresses iOl 000: one loop, 250 device addresses 064: 64 addresses iOl 000: two loops, 500 device addresses Wiring Class B or Class A Operating Voltage 24 VDC Operating Current (fully loaded loop) Standby: 55 mA Alarm: 80 mA Standby: 45 mA Alarm: 70 mA Note: These ratings do not include the use of two-wire smoke modules. Communication Line Max. 20.6 V peak-to-peak Voltage Terminal Rating 12 to 18 AWG (0.75 to 2.5 mm2) Circuit Current 0.5 A max. Max total loop 660 resistance Max total loop 0.5 i capacitance Isolators 64 isolators maximum per loop (total both isolator bases and modules) Ground Fault 0t05k0 Impedance Operating 32 to 120°F (0 to 49°C) Environment 0 to 93% noncondensing at 90°F (32°C) SA-ETH Ethernet Interface Card SA-ETH wiring To network The SA-ETH card provides a Network cable connec5on standard 10/100 Base T Ether- net network connection for connecting to an intranet, a local network, or the Internet. The I card can be used to download 1 Li I configuration programming from I I the 0-CU to the panel. The Ethernet card is installed on the plastic assembly and con- nects to the main circuit board via a ribbon cable. SA-ETH specifications Ethernet 10/100 Base T Operating environment Temperature 32 to 120°F (0 to 49°C) Humidity 0 to 93% RH, noncondensing at 90°F (32°C) RZI16-2 Remote Zone Interface Module . . . . -- :::1[ Lr ° - The AZI 16-2 Addressable Remote Zone Interface Module is an addressable device that provides connections for sixteen Class B Initiating Device Circuits and two Class B Supervised Output Circuits. The inputs and outputs can be configured individually for several device types. It requires 18 consecutive addresses on the Signaling Line Circuit (SLC). Addresses are assigned electronically. There are no address switches to set. The RZI1 6-2 incorporates two 8-segment DIP switches that are used to select the Alarm or Supervisory default device type for each of the 16 IDC circuits. The module also includes one 4-seg- ment DIP switch used to select the default Relay or NAC output device type. Device types other than the default are accomplished through programming. RZ116-2 Specifications Voltage 24V/Aux nominal: 24 VDC Supervisory current: 250 mA at 24 VDC nominal Alarm Current 1000 mA 24V/Aux minimum: 18.4 VDC 24V/Aux maximum: 26.4 VDC NAC1, NAC2 nominal: 24 VDC Current Standby current for 4.7 k EOL (U.S.) 4.8 mA' circuit Standby current for 3.9 k EOL (Canada) 5.7 mA/ circuit Alarm current at nominal voltage 31.1 mA! circuit Relay outputs Quantity 2 Type Rating (pilot duty) Programmable 24 VDC at 2.5 A Input circuit wiring 25 0 per wire resistance Initiating device circuits Quantity 16 EOL resistor 4.7 kO (U.S.); 3.9 kO Canada Zone voltage 22.78 V for 4.7 kO (U.S.) 22.08 V for 3.9 kO (Canada) Alarm current 31.1 mA/ channel at nominal voltage Alarm impedance range <680 0 Trouble impedance range > 5.55 kO Supervised output circuits EOL resistor 15 kO Quantity 2 Short circuit detection <2.6 kO Open circuit detection > 61.9 kO Contact ratings 24 VDC at 2.5 A (5 A for two NACs) Compatible cabinets MFC(A), iO1 000, APS Page 5of8 DATA SHEET E85001-0135 Not to be used for installation purposes. Issue 1 SA-DACT wiring T.-all ejack The dialer phone lines connect to connectors on the dialer's main circuit board. Phone line 1 connects to connector J4 and phone line 2 connects to connector J1. (3) (4) (5) (1)LED 1 LED 2 LED Expander 1 LED Expander 2 /Jarnt/non-alarm and trouble zone LEDs SA-DACT Dialer The SA-DACT provides communications between the control panel and the central station over a telephone line system. It transmits system status changes (events) to a compatible digital alarm communicator receiver over the public switched telephone network. The dialer is capable of single, dual, or split reporting of events to two different account and telephone numbers. The modem feature of the SA-DACT can also be used for uploading and downloading panel configuration, history, and current status to a PC running the 0-CU. The SA-DACT queues mes- sages and transmits them based on priority (alarm, supervisory, trouble, and monitor). Activations are transmitted before restora- tions. The SA-DACT is installed on the plastic assembly and connects to the main circuit board via a ribbon cable. SA-DACT specifications Phone line type One or two loop-start lines on a public, switched network Phone line connector RJ-31/38X (031138X) Communication formats Contact ID (SlA DC-OS) Operating environment Temperature 32 to 120°F (0 to 49°C) Humidity 0 to 93% RH, noncondensing at 90°F (32°C) Compatible DACRs Receiver Models Formats Ademco 685 Contact ID FBII CP220 Contact ID Osborne-Hoffman OH 2000 Contact ID Bosch D6600 Contact ID Silent Knight 9800 Contact ID Sur-Gard SG-MLJR1, MLR2 Contact ID SA-232 RS-232 interface The SA-232 card provides an RS-232 in- SA-232 wiring terface with iO panels. It can be used for GND (black wire) D(D (white wire) connecting a pnnter to the control panel rtxo (red wire) to print system events. The card also can be used for connecting a computer to download a configuration program 0l from the iO-CU to the control panel. 00 The RS-232 card is installed on the plas- tic assembly and connects to the main circuit board via a ribbon cable. SA-232 specifications Operating voltage Standard ElA-232 Terminal rating 12 tol8 AWG (0.75 to 2.5 sq mm) Operating environment Temperature 32 to 120°F (0 to 49°C) Humidity 0 to 93% RH, noncondensing at 90°F (32°C) SA-CLA Class A Module (i064 only) The SA-CLA card provides Class A capability for NAC wiring. Its terminal block provides the wiring connection for NAC return wiring. The card is required for annunciator Class A wiring even though this wiring does not return to the SA-CLA card. The SA- CLA is compatible with i064 control panels only. iOl000 panels are Class A Ready. The SA-CLA is installed directly to the control panel circuit board using its plastic standoffs and plug connection. SA:CLA specifications Operating voltage 24 VRNR Operating current 3.75 A FWR total at 120/230 VAC 60 Hz 3.0 A FWR total at 230 VAC 50 Hz 2.5 A max per circuit Circuit impedance 26 ohms, 0.35uF Terminal rating 12 tol8 AWG (0.75 to 2.5 sq mm) Operating environment Temperature 32 to 120°F (0 to 49°C) Humidity 0 to 93% RH, noncondensing at 90°F (32°C) D16L-iO LED Display Expander (i01 000 only) The D1 6L-i0 LED Display Expanders provide LED annunciation for up to 16 zones. It provides two LEDs for each zone. Two D1 6L-i0 LED display expanders can be installed in each iOl000 panel. Page 6of8 DATA SHEET E850010135 Not to be used for installation purposes. Issue 1 Notification appliance circuits i064 1 loop Class B or Class A (Styles 4, 6, 7) supporting up to 64 device addresses (any combination of detectors and modules) Maximum T-taps: 63 (each device can be on its own branch) 2 Class B (Style 'r', Class A (Style Z) optional 3.75 A FWR total at 120/230 VAC 60 Hz 3.0 A FWR total at 230 VAC 50 Hz 2.5 A FWR each max. per circuit 120 VAC, 60 Hz, 1.3 A max. 230 VAC, 50-60 Hz, 0.62 A max, 155 mA 204 mA 16 max. 8 drops max., RS-485 Class B, Class A is optional Data line length: 4,000 ft. (1,219 m) 24 VDC panel iO1000 1 loop, expandable to 4, Class A or B (Styles 4, 6, 7), each loop supporting up to 250 device addresses (125 detectors and 125 modules max.). Addresses 1 to 125 are for detectors and addresses 126 to 250 are for modules Maximum T-taps/loop: 124 4 Class B (Style Y) or 2 Class A (Style Z) 6.0 A FWR total at 120/230 VAC 60 Hz 5.0 A FWR total at 230 VAC 50 Hz 2.5 A FWR each max. per circuit 120 VAC, 60 Hz, 2.0 A max. 230 VAC, 50-60 Hz, 0.97 A max. 172 mA 267 mA 32 max. 8 drops max., RS-485 Class A or B Data line length: 4,000 ft. (1,219 m) Specifications Device loops Primary power Base panel current standby Base panel current alarm Input zones Remote annunciator Operating voltage Auxiliary power output Aux power 1: 500 mA, 24 VDC circuit Aux power 2: 500 mA, 24 VDC (1 A possible if you reduce total available NAC power by 500 mA) Output: 28.3 to 21.9 VDC, special application Note: Fora list of compatible devices, see the 1064 and 101000 Series Compatibility List (P/N 3102353-EN) Loop circuit Maximum loop resistance: 66 0 Maximum loop capacitance: 0.5 pF Communication line voltage: Maximum 20.6 V peak-to-peak Operating current (fully loaded loop) Stand by: 55 mA/45 mA Alarm: 125 mN1 15 mA (not including two-wire smoke modules) Circuit current: 0.5 A max. Style 4, 6, and 7 wiring Max. resistance between isolators: Limited only by overall wire run lengths 64 isolators maximum per loop (total both isolator bases and modules) Batteries Type: Sealed lead acid Voltage: 24 VDC Charging current: 2.47 A max. Amp hour capacity: 26 Ah Standby operation: 24 hour or 60 hour Placement: Up to two 10 Ah batteries will lit in the i064 control panel cabinet and two 18 Ah batteries will fit in the iOl 000 control panel cabinet. If larger batteries are required, use an EDWARDS battery cabinet. SA-DACT dialer Phone line type: One or two loop-start lines on a public, switched network Phone line connector: RJ-31/38X (C31/38X) Communication formats: Contact ID (SIA DC-OS) Operating current Standby/Alarm: 41 mA Max.: 100 mA FCC registration number: GESAL01 BSADACT Industry Canada Registration number: 3944A-SADACT Ringer equivalence number: 0.1 B Ground fault impedance 0 to 5 kO Alarm contact Form C N.O. 24 VDC at 1 A (resistive load) Trouble contact Form C 24 VDC at 1 A (resistive load) Supervisory contact Form A N.O. 24 VDC at 1 A (resistive load) Environmental Temperature: 0 to 49°C (32 to 120°F) Relative humidity: 0 to 93% noncondensing Terminal rating All terminals rated for 12 to 18 AWG (0.75 to 2.5 mm2) Page 7of8 DATA SHEET E850010135 Not to be used for installation purposes. Issue 1 LIFE SAFETY & INCIDENT MANAGEMENT Contact us... Email: edwards.fire@fs.utc.com Web: Edwards-fire.com EDWARDS is a UTC brand. 1016 Corporate Park Drive Mebane, NC 27302 Ordering Information Part Description 1101000 Fire Alarm Systems I01000G Four loop system with one 250-point loop installed. 110v, gray door. I01000G-2 Four loop system with one 250-point loop installed. 230v, gray door. 101000G-2-PG Four loop system with one 250-point loop installed. 230v, gray door, Portuguese. I01000G-2-SP Four loop system with one 250-point loop installed. 230v, gray door, Spanish. I01000G-CA Four loop system, one 250-point loop installed. liov, gray door, LED strips, Canada. I01000GD Four loop system, one 250-point loop installed. 110v, gray door, with dialer. 101000G-F Four loop system, one 250-point loop. 110v, gray door, LED strips, French Canada. I01000G-PG Four loop system with one 250-point loop installed. 110v, gray door, Portuguese. 101000G-SP Four loop system with one 250-point loop installed. 110v, gray door, Spanish. 101000R Four loop system with one 250-point loop installed. 110v, red door. I01000R-2 Four loop system with one 250-point loop installed. 230v, red door. @2016 United Technologies Corporation. I01000RD Four loop system, one 250-point loop installed. ii 0v, red door, with dialer. All tights reserved. SA-TRlM2 101000 Flush mount trim, black. 1064 Fire Alarm Systems (lO64Gj One loop system with one 64-point loop installed. 110v, gray door. 1064G-2 One loop system with one 64-point loop installed. 230v, gray door. 1064G-2-PG One boo system with one 64-ooint boo installed. 230v. arav door. Portuauese. I064GD One loop system, one 64-point loop installed. 11 Ov, gray door, with dialer. I064GL One loop system, one 64-point loop installed. 1 10v, gray door, English Canada. 1064GL-F One loop system, one 64-point loop installed. 1 10v, gray door, French Canada. 1064G-PG One loop system with one 64-point loop installed. 110v, gray door, Portuguese. 1064G-SP One loop system with one 64-point loop installed. 110v, gray door, Spanish. 1064R One loop system with one 64-point loop installed. 110v, red door. 1064R-2 One loop system with one 64-point loop installed. 230v, red door. 1064RD One loop system, one 64-point loop installed. 110v, red door, with dialer. SA-TRIM1 1064 Flush mount trim, black Option Cards i0-SDC1 Expansion module, one 250-device loop. i0-SDC2 Expansion module, two 250-device loops, 500 devices total. For iOi 000 only. RZ116-2 Remote Zone Interface Module. 16 Class B lDCs, 2 Class B Output. Includes bracket. SA-DACT Dual Line Dialer/Modem, supports Contact ID, mounts in cabinet on base plate. SA-232 RS-232 Serial Port for connection to printers & computers, mounts in cabinet. SA-ETH Ethernet Port. Slave, mounts in cabinet on base olate. SA-CLA Class A adapter module. Provides Class A capacity on NACs. Mounts in cabinet on main board. i064 systems only. D16L-iO-2 LED Annunciator module, 16 X 2-LED zones (4 programmable for sup). Mounts in cabinet to right of LCD display for zones 17-32. For 101000 only. D16L-iO-1 LED Annunciator module, 16 X 2-LED zones (4 programmable for sup). Mounts in cabinet to left of LCD display for zones 1-16. For 101000 only. D8RY-i0-2 Canada only: LED Annunciator module, two LEDs per zone, 16 zones (4 alarm only, 8 supervisory only, 4 alarm or supervisory). Mounts in cabinet. For i01000 only. D8RY-i0-1 Canada only: LED Annunciator module, two LEDs per zone, 16 zones (4 alarm only, 8 supervisory only, 4 alarm or supervisory). Mounts in cabinet. For 101000 only. Accessories CTM City Tie Module. 2-gang. Connection to a local energy fire alarm box. MFC-A Multifunction Fire Cabinet, 8' x 14" x 3.5" - red. SIGA-REL Releasing Module PT-11S System Printer BC-1 Battery Cabinet. 14.0" x 18.25" x 7.25". Holds two 12V24A batteries. BC-1R Battery Cabinet - Red. 14.0" x 18.25" x7.25". Holds two 12V24Abatteries. BC-i EQ Seismic hardening Kit for iO series panels. Includes battery hardening for BC-1 enclosure and components to harden panel internal components. Programming Tools i0-CU 10 Series configuration and diagnostics utility. Page 8of8 DATA SHEET E850010135 Not to be used for installation purposes. Issue 1 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL - FIRE ENGINEERING. BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. (7165-1657:O244 Page 1 of 2 CATEGORY: 7165 -- FIRE ALARM CONTROL UNIT (COMMERCIAL) LISTEE: EDWARDS, A Division of UTC Fire & Security Americas Corporation, Inc.8985 Town Center Parkway, Bradenton, 34202 United States Contact: Jewell Conover (941) 739-4358 Fax (941) 308-8123 Email: rhonda.conover@fs.utc.com DESIGN: Single and multi-loop analog addressable fire alarm control unit. Local, local with shunt, auxiliary, remote station, central station, releasing device. Power limited, non-coded, coded, shunt, reverse polarity, DACT, manual, automatic waterflow and sprinkler supervisory service. Models 'EST" i01000G, iO1000G-2, iOI000GD, i01000R, iO1000R-2, i01000RD7i4 i064-GD, i064-R, i064-RD, i064G-2, iO64R-2; i0500G, i0500GD, i0500R, i0500RD, i0500G-2, iO500R-2. Models 'Vigilant/Kidde" VSI-G, VSI-GD, VSI-R, VSI-RD, VSI-G-2, VSI-R-2; VS2-G, VS2-GD, VS2-R, VS2-RD, VS2-G-2, VS2-R-2, vs4-G, vs4-G-2, vs4-GD, vs4-R, vs4_r-2, vs4-RD,. Models 'FireworXlKidde" FX-64G, FX-64G0, FX-64R, FX-64RD, FX64G-2, FX-64R-2, FX-254G, FX-254GD, FX-254R, FX-254R0, FX254G-2, FX-254R-2, FX-1000, FXI000D. Models 'Edwards Signaling" E-FSA64G, E-FSA64GD, E..FSA64R, E-FSA64RD, E-FSA250G, E-FSA250GD, E-FSA250R, E-FSA250RD System Components: SA-DACT; Dialer SA-CLA; Class A Adapter SA-ETH; Ethernet Adapter SA-232; RS232 Module DI6L-iO, -VS, -Fa, D8RY-iO-1, D8RY-iO-2, D8RY-VS, 16 Zone Front Panel LED XAL250, V-SLC, XALI27; SLC Loop Driver io-SDCI, V-SLC2-1, FX-SLCI Single SLC Card, 250pt io-SDC2, V-SLC2-2, FX-SLC2 Dual SLC Card, *500pt *PT1S: System Printer *PTI -P: System Printer Parallel Refer to listee's data sheet for additional detailed product description and operational considerations. RATING: 120/230 VAC INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances, and in a manner acceptable to the authority having jurisdiction. '10-24.16 dc To This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2018 Listing Expires (June 30, !) Authorized By: DAVID CASTILLO, Program Coordinator Fire Engineering Division Listing No. 7165-1657:0244 Page 2 of 2 MARKING: Listee's name, model number, electrical rating, and UL label. APPROVAL: Listed as fire alarm control units for use with separately listed compatible initiating and indicating devices. *These control units meet the requirement of UL 864, 9th Edition Standard. *102416 dc . This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct 1*V% operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2018 Listing Expires (June 30, 2019) Authorized By: DAVID CASTILLO, Program Coordinator Fire Engineering Division ACE-Il FIRE ALARM DOCUMENTS The FAD is the perfect fit to meet the demanding code requirements today. SAE's number one goal is to manufacture code compliant solutions and this product allows you to do just that. NFPA 72 2007 section 6.2.2.1 states, "A record of installed software and firmware version numbers shall be maintained at the location of the fire alarm control unit." This durable 16 gauge steel enclosure with a solid piano hinge and key lock will keep all of your code required documents in one safe place. With a 4GB USB flash drive it stores your fire alarm software safe and secure eliminating the occurrences of the soft- ware not being on site when technicians arrive to service the system. Along with your fire alarm soft- ware you can store your test & inspection docu- ments, service records, manuals & AS built drawings for the system. Using a standard USB B connector it allows you to plug in with any standard SIB printer cable to upload or download information. The FDB is designed to hold critical manuals and documents with a durable steel retainer. It has designated hooks to organize key rings and hold important business cards for easy access and reference. Inside the cover it has a organized note table that allows for documentation for passwords and other critical system information. Standard Features: Installed with a 4 gig digital flash drive with USB B connector 2 Key ring hooks to hold system keys Business card holder for key contacts Overall Dimensions are 12" x 13" tall and 2 1/4 deep 16 gauge steel box and cover for security Durable powercoat baked on finish other colors available Standard %"cat 30 key lock other lock as- semblies available Solid stainless steel piano hinge Permanently screened white ink 1" high "Fire Alarm Documents" Legend sheet for passwords and system information [07] fAM-11100—M-002f QMe_~__e1 ISO spol Space Age Electronics, Inc. wililillillft 1W REGISTERED www.Isae.com NFPA tdMOANY 800.486.1723 Toll Free MUBER Made In ~U.S.A. 508.485.0966 Local 508.485.4740 Fax Space Age Electronics, Inc. 2009 No Excuses, Just Solutions! ED0549 LT10559 Rev.D 1/2 /SPACE AGE /ELECTRONICS, INC. Specifications: The fire alarm documents box (FAD) shall be UL Listed, constructed of 18 gauge cold rolled steel. It shall have a red powder coat epoxy finish. The cover shall be permanently screened with 1" high lettering "FIRE ALARM DOCUMENTS" with white indelible ink. The access door shall be locked with a 3/4" barrel lock and the hinge shall be a solid width 12" stainless steel piano hinge. The enclosure will supply 4 mounting holes. Inside the enclosure will accommodate standard 8 1/2 x 11 manuals and loose document records that will be protected within the enclosure. A legend sheet will be permanently attached to the door for system required documentation, key contacts and system information. The FAD will have securely mounted inside a minimum of 4 Gigabyte digital flash memory drive with a standard USB B connector for uploading and downloading information. The drive shall not be accessible without tools to any person whom gains access to the records. The enclosure shall also provide 2 key ring holders with a location to mount standard business type cards for key contact personnel. USB Storage Interface Requires Standard USB-B Connector Popofly lnf,m,atlo,, Minimon, Roqnl,nd Ooonn,ont,tlnn (SIG-M) tIfl. 72.7) C 602110,76 and Appl20010 18.1 S6002,llfl000l)otlo0 Contlocla 0,0SWFA4S7fl0.d0,0,, 4s0,2nos=%2.t.764sJ=adnohn,nwk,= Ta________ U,tt 16.5 An1ho21y H64)ng Jlri0didiOfl I*PA.t4, 00,7 t IO00,OWS0,200,ISO*0K412fl,S,7724flIjZ '41. II Equipment 1210,0,066, no.464.102 ..tI...no 1170641 664.7 Legend sheet for storing system information including contacts, sign-off, maintenance & test information, and alternate locations of additional records. Space Age Electronics, Inc. www.lsae.com 800.486.1723 Toll Free 508.485.0966 Local 508.485.4740 Fax No Excuses, Just Solutions! Ordering Information: Part # Description SSU00685 Fire Alarm Storage Cabinet RED SSU00686 Custom screening with your Logo Check out our Infinity line eFAD single gang 2 Gig digital storage solutions (IAMEFAD) This document is subject to change without notice, see doc # ED0479 for legal disclaimer ED0549 LT10559 Rev.D 2/2 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL rwi;i FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. (7300-0553:01 1'9 Page 1 of 1 CATEGORY: 7300 -- FIRE ALARM CONTROL UNIT ACCESSORIES/MISC. DEVICES LISTEE: SPACE AGE ELECTRON ICS58 Chockett Road, Sterling, MA 01564 Contact: Robert Scholl (508) 485-0966 Fax (508) 485-4740 Email: bobs@lsae.com DESIGN: Models TC2-32, TC1-18, TCXIA 64, TCX/D 128, ACE/A, AC2, ACE/D, IF-2, IFI, IFX/A and IFXID enclosures. Models CE-1 ACE-12 and ACE-13, *ACE2424, *ACE 3036, *ACE 2436, *ACE 3048 document cabinets. Refer to listee's data sheet for detailed product description and operational considerations. INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number and UL label. APPROVAL: Listed as fire alarm equipment enclosures and document cabinets for use with listee's fire alarm equipment. Refer to listee's Installation Instruction Manual for details. 02-09-16 do This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2018 Listing Expires 30, 2019) Authorized By: DAVID CASTILLO, Program Coordinator Fire Engineering Division From Tyco Security Products Features That Make a Difference: Uses LIE network for high- speed, reliable and low-cost communications to an IF receiver Automatically switches to 3G (HSPNHSPA+) if LTE service is not available Compatible with control panels that communicate using Contact ID or SIA (300 baud) formats Full event reporting 4 on-board inputs with NC, NO or SEOL supervision 4 on-board outputs (open collector) Activation and initialization via website or mobile interface provided by C24 Communications View communicator status directly from your mobile phone to support on-site or remote troubleshooting Compatible with Sur-Gard® System l-lP/ll/lll/IV/5 monitoring station receivers Includes UL listed power supply, transformer and 7 Ah rechargeable battery UL 864 listed CSFM listed The LE401OCF connects the alarm control panel to the Cellular network and reports alarm signals directly to a monitoring station receiver (Sur-Gard System I -IF/Il/Ill/I V/5). The LE4O1OCF uses the Cellular network to ensure low-cost, high-speed and reliable alarm communications and is compatible with control panels that communicate using the Contact ID or SIA (300 baud) format. The LE401OCF is compliant with the latest requirements for Communications Methods as per UL864 and NFPA72 2010, 2013, and 2016 editions. It can be used in Fire Monitoring applications as a single communications technology, in which case any failure of the communications path shall be annunciated at the supervising station within 5 minutes (NFPA72 2010) or 1 hour (NFPA72 2013/2016) of the failure, or it can be used as part of a multiple communications technologies (for example in conjunction with a DACT). When used as a back-up provision shall be made to monitor the integrity of each communication path and failure of any communications path shall be annunciated at the supervising station and at the protected premises within not more than 24 hours of the failure. How it Works The LE401OCF can be used as either a Sole Communicator or as a Backup Communicator. When being used as a Sole Communicator the LE401 OCF will replace the phone line connection on the panel and as soon as it detects that an alarm needs to be transmitted it will send the alarm across the Cellular network immediately. When being used as a backup the communicator assesses the connection to the PSTN phone line, and only in the event of a phone line failure will it send all alarm traffic across the Cellular network to the monitoring station. Ensure your installations are future-ready, with LTE Due to rapidly-evolving cellular technologies, 2G/3G network sunsets are already on the horizon - with some having already been completed. Now's the time to adopt and adapt. Switch to LIE today, to offer customers long-lasting investment protection, and reduce your future truck rolls. . . •. .(s1ai1i.luI.1[sb[•].k 1jL/!I. ,... ... ...: • . ,... ....... DSD From Tyco Security Products In instances where the control panel does not support Contact ID or SIA (300 baud), the LE401OCF has inputs pre- set to transmit fire alarm, fire supervisory or system trouble. Alarm signals are transmitted directly without the need of a clearinghouse to the IP linecard of the monitoring station receiver (Sur-Gard® System l-IP/11/111/1V/5). Activating & Initializing the Unit Activating and initializing the LE401 OCF can be done using the website interface provided by C24 Communications. No special tools are required. Mobile Site for Easy Installation and Comprehensive Maintenance C24 Communications mobile site (m.connect24.com) makes the installation a simple process and offers intuitive trouble-shooting features, cutting down on time and cost allocated to maintenance. UL Listing The LE401 OCF is UL listed under File S4019, Listing guide UOXX, as a sole or backup communicator for Commercial Fire monitoring installations. When used as a sole communicator under NFPA72 2010 guidelines the LE401 OCF will send its heartbeat once every 97 seconds ensuring that three heartbeats will be received at the supervising station within the 300 second window. When used as a sole communicator under NFPA72 2013/2016 guidelines the LE401OCF will send its heartbeat once every 5 minutes to monitor connectivity with the supervising station within the 1 hour window. When used as a backup communicator the LE401OCF will monitor the other communication method (DACT) and send a daily test transmission to the supervising station. CSFM Listing The LE401OCF has been approved by the California State Fire Marshal (CSFM) pursuant to Section 13144.1 of the California Health and Safety Code. Ordering Information: LE4O1 OCF-AT .............. Universal Wireless Commercial Fire Alarm Communicator Rate Plan Cost-effective rate plans have been negotiated and are available through authorized master resellers. Contact your monitoring station or visit www.connect24.com to find a master reseller. When used as a sole communicator, the LE401OCF requires use of the 4MB (NFPA72 2010) or 5001<13 (NFPA72 2013/2016) rate plans to support the supervision requirements. Specifications Dimensions ................................................ 11-1/2"x10 x3 (290 mm x 254 mm x 75 mm) Input Voltage.............................................................120 VAC Current Draw ............................................. 0O)(standby) C40701 Operating Environment ................32° to 120° F (00 to 49° C) Weight...........................................................12.8 lbs (5.8 kg) Optional Acessories Model Description LTE-1 5ANT 15 ft extension antenna LTE-25ANT 25 ft extension antenna LTE-50ANT 50 ft extension antenna 0 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL U FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. (7300-1273:06 Page 1 of 1 CATEGORY: 7300 - FIRE ALARM CONTROL UNIT ACCESSORIES/MISC. DEVICES LISTEE: Digital Security Controls95 Bridgeland Ave, Toronto, Ontario M6A 1Y7 Canada Contact: Dan Nita (905) 760-3000 Fax (905) 760-3020 Email: dnita@tycoint.com DESIGN: ModelLE4010CFLTE interface. Refer to listee's data sheet for additional detailed product description and operational considerations. RATING: 120 VAC INSTALLATION: In accordance with listee's printed installation instructions, NFPA 72, applicable codes & ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating, and UL label. APPROVAL: Listed as a interface for use with a separately listed fire alarm control unit. Refer to listee's Installation Instruction Manual for details. NOTE: Burglary and other non-fire functions were not examined. 01-11-18 gt This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2018 Listing Expires (June 30, 2019) Authorized By: DAVID CASTILLO, Program Coordinator Fire Engineering Division =RM-2Relay Module Installation Instructions The RM-2 Relay Module is used as an end-of-line (EOL) power supervision module for 4-wire smoke detectors. The RM-2 is used with the Polarity Reversal Module PRM- 4W and DSC FSA-41 0 series smoke detectors. When the PRM-4W reverses polarity on the smoke detector loop to activate all smoke detector sounders, the RM-2 Relay will continue to operate normally (regardless of input power polarity). Refer to the PRM-2W/4W Polarity Reversal Module Installation Instructions Technical Specifications: Operating Voltage Range: .............................................................. 10VDc to 30VDC Relay Contact Rating: .....................................................................2A@30VDcNAC CurrentRating: ..............................................................................................25mA Operating Environment: ...................................................0°C - 49°C (32°F - 120°F) ...............................................5% - 93% RH (non-condensing) Size (HxWxD) ...................................28.5 x86x21mm/ 1 1/8 x x 7/8 in. Terminal Wire Gauge: ............................................................................ 14-22 AWG Connection Diagram Run the connection wires through the wiring holes on the back of the unit. Mounting To mount the unit, remove the plastic cover and secure the unit to the desired loca- tion with the screws provided. Replace the cover. The module can also be mounted inside a standard 4" electrical box (1.5" deep) if required by the installation. Please refer to the diagrams below: 4-WIRE SMOKE DETECTORS PRM-4W FSA-41 0 Series Polarity Reversal Module 4-wire Smoke Detector Control Panel P+ P I I 111111 Zx Corn I ++ — NOC _J Lj_______ 12 Voc—' Ivy —Panel EOLR BLKIII II 0 INC ______ I REDIIeI COM 10 DSC RM-2 Relay I I NO '-'II Mounting of the Relay in an Electrical Box 4-Wire Smoke Detector Smoke Detector Mounting Plate Power Supervision Relay RM-2 Electrical Box (1.5" deep) LIMITED WARRANTY Digital Security Controls Ltd. warrants that for a period of twelve months from the date of purchase, the product shall be free of defect in materials and workmanship under normal use and that in fulfilment of any breach of such warranty, Digital Security Controls Ltd. shall, at its option, repair or replace the defective equipment upon return of the equipment to its repair depot. This warranty applies only to defects in parts and workmanship and not to damage incurred in shipping or handling, or damage due to causes beyond the control of Digital Security Controls Ltd. such as lightning, excessive voltage, mechanical shock, water damage, or damage arising out of abuse, alteration or improper application of the equipment. The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other warranties, whether expressed or implied and of all other obligations or liabilities on the part of Digital Se- curity Controls Ltd. This warranty contains the entire warranty. Digital Security Controls Ltd. neither as- sumes, nor authorizes any other person purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product. In no event shall Digital Security Controls Ltd. be liable for any direct, indirect or consequential damages, loss of anticipated profits, loss of time or any other losses incurred by the buyer in connection with the purchase, installation or operation or failure of this product. WARNING: Digital Security Controls Ltd. recommends that the entire system be completely tested on a reg- ular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electri- cal disruption, it is possible for this product to fail to perform as expected. ©2003 Digital Security Controls Ltd. IllIllIllOIll II II liii IltIllIllUIll III Toronto, Canada • www.dsc.com Printed in Canada 29034640R002 Direct all comments concerning this publication to pubs@dscltd.com CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. CATEGORY: LISTEE: DESIGN: RATING: INSTALLATION MARKING: APPROVAL: NOTE: (7300-1273:0127 Page 1 of 1 7300 - FIRE ALARM CONTROL UNIT ACCESSORIES/MISC. DEVICES Digital Security Controls95 Bridgeland Ave, Toronto, Ontario M6A 1Y7 Canada Contact: Dan Nita (905) 760-3000 Fax (905) 760-3020 Email: dnita@tycoint.com Models PRM-2W, -2WC (for 2-wire smokedetectors), PRM-4W, -4WC(for 4-wire smoke detectors) power reversal modules andRM-2 'power supervision relay modules. Refer to listee's data sheet for additional detailed product description and operational considerations. In accordance with listee's printed installation instructions, applicable codes & ordinances and in a manner acceptable to the authority having jurisdiction. Listee's name, model number, electrical rating, and UL label. Listed as control unit accessories for use with listee's separately listed compatible fire alarm control units. Refer to listee's Installation Instruction Manual for details. 09-30-03 This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2018 Listing Expires (June 30, 201 Authorized By: DAVID CASTILLO, Program Coordinator Fire Engineering Division EDWARDS Catalog ) Intelligent Initiating Devices UtjTEiijies LIFE SAFETY e INCIDENT MANAGEMENT Intelligent Smoke Detector (SIGA-PD) - , / t. 0• \ _v Overview The Signature Series SIGA-PD optical smoke detector brings ad- vanced sensing technology to a practical design that increases ef- ficiency, saves installation time, cuts costs, and extends life safety and property protection capabilities. Continuous self-diagnostics ensure reliability over the long-haul, while environmental compen- sation helps reduce maintenance costs. Like all Signature Series detectors, the SIGA-PD is an intelligent device that gathers analog information from its optical sensor, converting this data into digital signals. To make an alarm decision, the detector's on-board microprocessor measures and analyzes sensor readings and compares this information to historical data. Digital filters remove signal patterns that are not typical of fires, thus virtually eliminating unwanted alarms. Standard Features Note: Some features described here may not be supported by all control systems. Check your control panel's Installation and Operation Guide for details. Next Generation Optical Smoke Sensing Technology Wide 0.53 to 3.94 %/ft. (1.7 to 12.35 %/m) smoke obscuration Uses Existing Wiring Automatic Device Mapping Up To 250 Total Signature Addresses Per Loop Two Levels of Environmental Compensation Two Levels of Dirty Detector Warning Twenty Pre-Alarm Settings Five Sensitivity Settings Non-Volatile Memory Electronic Addressing Identification of Dirty or Defective Detectors Automatic Day/Night Sensitivity Adjustment Bicolor (Green/Red) Status Led Standard, Relay, Fault Isolator, and Audible Mounting Bases Sensor Markings Provide Easy Testing Identification Page lof4 DATA SHEET E85001-0646 Not to be used for installation purposes. Issue 1 Application The SIGA-PD detects extremely small particles of combustion and triggers an alarm at the first sign of smoke. Thanks to its high- performance forward-scattering reflective response technology, the photoelectric smoke sensor responds quickly and reliably to a wide range of fire types, especially slow burning fires fuelled by combustibles typically found in modern multi-use buildings. Compatibility The SlGA-PD detector is compatible only with the Signature Loop Controller. Installation Signature Series detectors mount to North American 1-gang boxes, 3-1/2 inch or 4 inch octagon boxes, and to 4 inch square elec- Self-ockffg tab trical boxes 1-1/2 inches (38 mm) deep. They mount to European BESA and 1-gang boxes with 60.3 mm fixing centers. See mounting LEO Indicator base installation and wiring for more information. Sensing and reporting technology The microprocessor in each detector provides additional benefits - Self-diagnostics and History Log, Automatic Device Mapping, and Fast, Stable Communication. Self-diagnostics and History Log - Each Signature Series detector constantly runs self-checks to provide important mainte- nance information. The results of the self-check are automatically updated and permanently stored in the detector's non-volatile memory Automatic Device Mapping - The loop controller learns where each devices serial number address is installed relative to other devices on the circuit. The mapping feature provides supervision of each device's installed location to prevent a detector from being reinstalled (after cleaning etc.) in a different location from where it was originally. Fast Stable Communication - On-board intelligence means less information needs to be sent between the detector and the loop controller. Other than regular supervisory polling response, the detector only needs to communicate with the loop controller when it has something new to report. Testing & Maintenance Each detector automatically identifies when it is dirty or defective and causes a 'dirty detector" message. The detector's sensitiv- ity measurement can also be transmitted to the loop controller. A sensitivity report may be printed to satisfy NFPA sensitivity mea- surements, which must be conducted at the end of the first year and every two years thereafter. The user-friendly maintenance program shows the current state of each detector and other pertinent messages. Single detectors may be turned off temporarily from the control panel. Availability of maintenance features is dependent on the fire alarm system used. Accessories Detector mounting bases have wiring terminals that are acces- sible from the "room-side" after mounting the base to the electrical box. The bases mount to North American 1-gang boxes and to 31/2 inch or 4 inch octagon boxes, 11/2 inches (38 mm) deep. They also mount to European BESA and 1-gang boxes with 60.3 mm fixing centers. The SlGA-SB4, SIGA-RB4, and SlGA-lB4 mount to North American 4 inch sq. electrical boxes in addition to the above boxes. They include the SIGA-TS4 Trim Skirt, which is used to cover the "mounting ears" on the base. The SlGA-AB4G mounts to a 4 inch square box only. SIGA-AB4GIT/LF SIGA-SB _SIGA-IB'l SIGA-RB SIGA-LED Audible Base Standard Base Isolator Baa' Relay Base Remote LED Remote LED SIGA-LED - The remote LED connects to the SlGA-SB or SlGA-SB4 Standard Base only. It features a North American size 1-gang plastic faceplate with a white finish and red alarm LED. SIGA-TS4 Trim Skirt - Supplied with 4 inch bases, it can also be ordered separately to use with the other bases to help hide surface imperfections not covered by the smaller bases. Sounder Bases - Signature Series sounder bases are designed for use where localized or group alarm signaling is required. SIGA-AB4G bases provide sounder capability to Signature Series to heat and smoke detectors. They are not intended for use with combination carbon monoxide detectors in Fire- plus-CO mode. SIGA-AB4GT bases provide sounder capability to Signature Series smoke and heat detectors, as well as carbon monox- ide detectors when used with a SlGA-TCDR Temporal Pattern Generator. SIGA-AB4G-LF bases provide 520 Hz low frequency sounder capability to Signature Series smoke and heat detec- tors, as well as carbon monoxide detectors when used with a SlGA-TCDR Temporal Pattern Generator. The SlGA-AB4G-LF is suitable for applications requiring low frequency audible tones. Page 2of4 DATA SHEET E850010646 Not to be used for installation purposes. Issue 1 Typical Wiring The detector mounting bases accept #18 AWG (0.75mm2), #16 Audible Sounder Bases, Fire Mode (1.0mm2), #14 AWG (1 .5mm2), and #12 AWG (2.5mm2) wire sizes. AB4G7 AB4G, AB4G-LF sounder bases Sizes #16 AWG (1.0mm2)and #18 AWG (0.75mm2) are preferred for ease of installation. __—•__•__\ ,' Standard Detector Base, SIGA-SB, SIGA-SB4 SIGA-AB4GT, ° SIGA-AB4G, SIGA-AB4G-LF: Jumper cuts (7 Volume Setting for EDWARDS Signature Series ax resistance Default = High detectors. The SIGA-LED Re- per wire Cut/remove HD st not exceed jumper for mote LED is supported by this 20 Ohms low dB I sja~Base. OAT D This is the basic mounting base J(-1 1 I Tern, Description I SW I 1 Not Used I I 2 DATA IN/OUT I Not Used I DATA IN(-) I I 4 Remote LED j-) I DATA IN DATA0UT I 5 Remote LED (+) I I 6 Not Used I 7 DATA OUT I-) DATA IN 1+1 DATA OUT 1+1 -, 24 Vdc In _____________________ From Signature Controller To Next Device From power supply or Previous Device or previous base Output Mode Default = Fire Cut/remove jumper for Fire plus CO SIGA-AB4G: Tone Setting Default = Temporal Cut/remove jumper for Steady SIGA-AB4GT: Not Used - 24 Vdc out To next base or EOL relay Isolator Detector Base, SIGA-113, SIGA-184 Data In - From Signature Controller or previous device + - Data out to next Signature device This base includes a built-in line fault isolator for use on Class A circuits. A detector must be installed for it to operate. The isolator base does not support the SIGA-LED Remote LED. OUT (-) LIU IL) JIUVlU tiltS ""lt) next isolator down the From Signature Controller line with power or Previous Device - when the isolator next to the short closes, it reopens within 10 msec. The process repeats beginning on the other side of the loop controller. Warnings & Cautions This detector does not operate without electrical power. As fires frequently cause power interruption, discuss further safeguards with the local fire protection specialist. This detector does not sense fires in areas where smoke cannot reach the detector. Smoke from fires in walls, roofs, or on the opposite side of closed doors may not reach the detector. Photoelectric detectors have a wide range of fire-sensing capabilities and are best suited for detecting slow, smolder- ing fires. In Canada, install according to CAN/ULC-S524 Standard for the Installation of Fire Alarm Systems, CSA C22.1 Canadian Electrical Code, and the local authority having jurisdiction. The isolator operates as follo - a short on the line causes all lators to open within 23 mse - at 10 msec intervals, beginning on one side of the Class A DA1 circuit nearest the loop controller, the isolators OUT (+) To Next Device Tern, Description 1 Not Used 2 DATA IN/OUT (+) 3 DATA IN (-) 4 Not Used 5 Not Used 6 DATA OUT (-) 7 Not Used Relay Detector Base, SIGA-RB, SIGA-RB4 Normally- Nomrdlr This base includes a relay. Nor- mally Open or Normally Closed operation is selected during in- stallation. The dry contact is rated for 1 amp (pilot duty) @ 30 Vdc. The relay's position is supervised to avoid accidentally jarring it out of position. The SlGA-RB can be DAT operated as a control relay if pro- grammed to do so at the control DATAINCv DATA OUT panel. The relay base does not homsionureconrroter ro Next oevice or Previous Device Term Description support the SlGA-LED Remote 1 Normally Open LED. CONTACT RATING I 2 DATA IN/OUT I I 1.0 Amp @ 30 VOC 3 Common (Pilot Duty) 4 5 6 7 DATA 114 1-) Not Used Normally-Closed I DATA OUT)-) Page 3of4 DATA SHEET E85001 -0646 Not to be used for installation purposes. Issue 1 Dimensions LIFE SAFETY & INCIDENT MANAGEMENT Contact us... Email: edwards.fire@fs.utc.com GO Web: Edwards-fire.com EDWARDS is UTC brand. 1016 Corporate Park Drive Mebane, NC 27302 © 2016 United Technologies Corporation. All rights reserved. Specifications 15.20 to 1 Normal operating current 2pA) Alarm current 32pA) Smoke Sensitivity Range ULJULC: 0.53 to 3.94 %/ft. (1.7 to 12.35 %Im) obscuration Vibration level 10 to 35 Hz, with an amplitude of 0.01 in. Air velocity 0 to 4,000 ft/mm (0 to 20 m/s) Wall mounting 12 in. (305 mm) max. from ceiling Compatible bases See Ordering Information Compatible detector testers Testifire 1000, Testilire 2000 Operating environment 32 to 120°F (0 to 49°C), 0 to 93% RH, noncondensing Construction High Impact Engineering Polymer, White toraye iemperauire -' to i 'fur -u to DtrL) Environmental compensation Automatic Agency Listings CAN/ULC-S529, UL 268, UL 268A Ordering Information Catalog Description Ship Wt. Number lbs (kg) (slGA-PD) Intelligent Optical Smoke Detector 0.4 (0.16) Accessories Detector Mounting Base - Standard A_inrh flatcrtnr NA- -fl— Poco A. uewctor iviounung riase w,rieiay SIGA-R34 4-inch Detector Mounting Base w/Relay, c/w Trim Skirt 0.2 (.09) SIGAiB) Detector Mounting Base w/Fault Isolator SIGA-lB4 4-inch Detector Mounting Base w/ Fault Isolator, c/w Trim Skirt SIGA-LED Remote Alarm LED (not for EN54 applications) SIGA-AB4G Audible (Sounder) Base for Fire Detectors 0.3 (0.15) SIGA-AB4G-LF Low Frequency Audible (Sounder) Base for CO and Fire Detectors 0.3 (0.15) SlGA-AB4GT Audible (Sounder) Base for CO and Fire Detectors 0.3 (0.15) SIGA-TS4 Trim Skirt (supplied with 4-inch bases) 0.1 (0.04) SlGA-TS Trim Skirt - (optional for non 4-inch bases) 0.1 (0.04) I(A-flMP flpthr.tcir Mrt intinci PIMP n ii 4) SIGA-VA Detector Cleaning Tool Page 4of4 DATA SHEET E85001 -0646 Not to be used for installation purposes. Issue 1 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. (72-1657:O) Page 1 of 2 CATEGORY: 7272 -- SMOKE DETECTOR-SYSTEM TYPE-PHOTOELECTRIC LISTEE: EDWARDS, A Division of UTC Fire & Security Americas Corporation, lnc.8985 Town Center Parkway, Bradenton, 34202 United States Contact: Jewell Conover (941) 739-4358 Fax (941) 308-8123 Email: rhonda.conover@fs.utc.com DESIGN: ModeIsSIGA-PD *SIGI..PD *KI..PD and *KIR..PD Analog addressable photoelectric smoke detectors.*Model SIGI-PO is similar to Model SIGA-PD except for isolation circuitry. *Model Kl-PD is identical to Model SIGA-PD except for trade name. *Model KlR-PD is similar to Model SIGA-PO except for control panel compatibility. Refer to listee's data sheet for detailed product description and operational considerations. RATING: 15.2-19.95 Vdc INSTALLATION: In accordance with listee's printed installation instructions, NFPA 72 and applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating and UL label. *Models SIGA-PD and SIGI-PO are under the Edwards brand. *Models KI-PD and KlR-PD are under the Kidde brand. APPROVAL: Listed as analog addressable photoelectric smoke detectors. *Model KI-PD is for use with listee's Models VSI, VS2 and VS4 (CSFM No. 7165-1657:0244); VM-1 (CSFM No. 7165-1657:0309) fire alarm control units. *Models SIGA-PD and SlGl-PD are for use with listee's Models EST3 (CSFM No. 7165-1657:0186); i064, i0500 and i01000 (CSFM No. 7165-1657:0244); EST3X (CSFM No. 7165-1657:0306) fire alarm control units. *Model KJR-PD is for use with listee's Models FX-64, FX-254 and FX-1000 (CSFM No. 7165-1657:0244) fire alarm control units. *Model SIGA-PD is for use with listee's bases: Models SIGA-SB, -SB4, -RB, -RB4, -lB, -I134 (CSFM No. 7300-1657:0120); SIGA-AB4G (CSFM No. 7300-1657:0222); SIGA-AB4GT (CSFM No. 7300-1657:0307) and SIGA-AB4G-LF (CSFM No. 7300-1657:0322). *Model 5101-PD is for use with listee's bases; Models SIG[-AB4G (CSFM No. 7300-1657:0222); SIGI-AB4GT (CSFM No. 7300-1657:0307) and SIGI-AB4G-LF (CSFM No. *Rev 02-15-18 gt , This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2018 Listing Expires (June 30, 2019) Authorized By: DAVID CASTILLO, Program Coordinator Fire Engineering Division Listing No. 7272-1657:0331 Page 2 of 2 7300-1657:0322). *Models KI-PD and KIR-PD are for use with listee's bases; Models Kl-ABST (CSFM No. 7300-1657:0222), KI-ABOT (CSFM No. 7300-1657:0307) and Kl-ABLT (CSFM No. 7300-1657:0322). Authority having jurisdiction should be consulted prior to installation. Refer to listee's Installation Instruction Manual for details. NOTE: The photoelectric type detectors are generally more effective at detecting slow, smoldering fires, which smolder for hours before bursting into flames. Sources of these fires may include cigarettes burning in couches or bedding. The ionization type detectors are generally more effective at detecting fast, flaming fires, which consume combustible materials rapidly and spread quickly. Sources of these fires may include paper burning in a waste container or a grease fire in the kitchen. *Rev 02-15-18 gt This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2018 Listing Expires(J une 30, 2019) Authorized By: DAVID CASTILL.O, Program Coordinator Fire Engineering Division SIGA-278 ULI uCLA /I/\ [1 MEA '? 7157 VLLV [!j 0129 18 EDWARDS Catalog Intelligent Initiating I NITA, FINE PmJR 10 - SM e.TU"nife—d~Ti-chnologies ~ LIFE SAFETY INCIDENT MANAGEMENT Manual Pull Stations SIGA-270, SIGA-270P, LSIGA-2§j7 Overview The SIGA-270 and SIGA-278 series Manual Pull Stations are part of EDWARDS'S Signature Series system. The SIGA-270 Fire Alarm Manual Pull Stations feature our very familiar teardrop shape. They are made from die-cast zinc and finished with red epoxy powder- coat paint complemented by aluminum colored stripes and mark- ings. With positive pull-lever operation, one pull on the station handle breaks the glass rod and turns in a positive alarm, ensuring protection plus fool-proof operation. Presignal models (SIGA-270P) are equipped with a general alarm (GA) keyswitch for applications where two stage operation is required. The up-front highly visible glass rod discourages tampering, but is not required for proper operation. EDWARDS's double action single stage SIGA-278 station is a contemporary style manual station made from durable red colored lexan. To initiate an alarm, first lift the upper door marked "LIFT THEN PULL HANDLE", then pull the alarm handle. Standard Features Note: Some features described here may not be supported by all control sys- tems. Check your control panel's Installation and Operation Guide for details. Traditional familiar appearance SlGA-270 models feature our familiar teardrop design with Simple positive pull action and sturdy die-cast metal body. One stage (GA), two stage (pie-signal), and double action models SIGA-270 models are available for one or two stage alarm systems. The single stage double action SlGA-278 features a rugged Lexan housing with keyed reset mechanism. Break glass operation An up-front visible glass rod on the SIGA-270 discourages tampering. Intelligent device with integral microprocessor All decisions are made at the station allowing lower com- munication speed while substantially improving control panel response time. Less sensitive to line noise and loop wiring properties; twisted or shielded wire is not required. ADA Compliant Meets ADA requirements for manual pull stations. Electronic Addressing with Non-volatile memory Permanently stores programmable address, serial number, type of device, and job number. Automatically updates historic information including hours of operation, last maintenance date, number of alarms and troubles, and time and date of last alarm. Automatic device mapping Each station transmits wiring information to the loop control- ler regarding its location with respect to other devices on the circuit. Diagnostic LEDs Status LEDs; flashing GREEN shows normal polling; flashing RED shows alarm state. Designed for high ambient temperature operation Install in ambient temperatures up to 120 OF (49 °C). Page 1 014 DATA SHEET E85001-0279 Not to be used for installation purposes. Issue I Application The operating characteristics of the fire alarm stations are deter- mined by their sub-type code or "Personality Code". NORMALLY- OPEN ALARM - LATCHING (Pesonality Code 1) is assigned by the actory; no user configuration is required. The device is configured or Class B IDC operation. An ALARM signal is sent to the loop controller when the station's pull lever is operated. The alarm con- dition is latched at the station. Typical Wiring The fire alarm station's terminal block accepts #18 AWG (0.75mm2) to #12 AWG (2.5mm2) wire sizes. See Signature Loop Controller catalog sheet for detailed wiring requirement specifications. Wiring Notes Refer to Signature Loop Controller manual for maximum wire distance. 2. All wiring is power limited and supervised. Compatibility Signature Series manual stations are compatible only with ED- WARDS's Signature Loop Controller. Warnings & Cautions This device will not operate without electrical power. As fires fre- quently cause power interruption, we suggest you discuss further safeguards with your local fire protection specialist. Testing & Maintenance To test (or reset) the station simply open the station and operate the exposed switch. The SIGA-270 series are opened with a tool; the SlGA-278 requires the key which is supplied with that station. The station's automatic self-diagnosis identifies when it is defec- tive and causes a trouble message. The user-friendly maintenance program shows the current state of each Signature series device and other pertinent messages. Single devices may be deactivated emporarily, from the control panel. Availability of maintenance features is dependent on the fire alarm system used. Scheduled maintenance (Regular or Selected) for proper system operation should be planned to meet the requirements of the Authority Having Jurisdiction (AHJ). Refer to current NFPA 72 and ULC CAN/ULC 536 standards. REAP VIEW ..; of 278 U.N Iii 8 7 • IS II H II (o/Acte) I . II armvi) Green LED Ted LED DATA IN (C)> DATA OUT W 1 DATA IN (-) > DATA OUT () From Signature Controller Y To Next Device or Previous Device Ai Figure 4. Single Stage Systems REAP VIEW Of r 270P. 270P8 C3 C3 . S • Red LED I II ____________ Green LED 4 ? 2 0 U1- CM { OAIAIN(.)> I IDATA OUT (,) DATA IN(-) pDATAOUT(-)J From Signature Controller 10 Next Device or Previous Device Figure 5. Two Stage Systems Page 2 of 4 DATA SHEET E85001-0279 Not to be used for installation purposes. Issue 1 Compatible Electrical Box 5 4 Back Plate o Key-latch Cover Release Installation Single-stage Signature Series fire alarm manual pull stations mount to North American 21/2 inch (64 mm) deep 1-gang boxes. Two stage presignal (270P) models require 11/2 inch (38 mm) deep 4-inch square boxes with i-gang, ½-inch raised covers. Openings must be angular. Rounded openings are not acceptable. Recommended box: Steel City Model 52-0-13: in Canada, use Iberville Model C 52-0-49-1/2. All models include terminals are suited for #12 to #18 AWG (2.5 mm2 to 0.75 mm2) wire size. EDWARDS recommends that these fire alarm stations be installed according to latest recognized edition of national and local fire alarm codes. Electronic Addressing: The loop controller electronically addresses each manual station, saving valuable time during system com- missioning. Setting complicated switches or dials is not required. Each station has its own unique serial number stored in its on-board memory. The loop controller identifies each device on the loop and assigns a 'soft" address to each serial number. If desired, the stations can be addressed using the SlGA-PRO Signature Program/Service Tool. Figure 1. SIGA-278 installation Compatible Electrical Box Cover 4 ReleasE Screw 06 Bock Plate 'S Toggle Switch VIU e "b Gass Rod Release Lever Figure 2. SIGA-270, SIGC-270F, SIGC-270B installation Cover Release Figure 3. SIGA-270P, SIGC-270PB installation Page 3of4 DATA SHEET E850010279 Not to be used for installation purposes. Issue 1 LIFE SAFETY & INCIDENT MANAGEMENT Contact us... Email: edwards.fire@fs.utc.com Web: Edwards-fire.com EDWARDS is a UTC brand. 1016 Corporate Park Drive Mebane, NC 27302 © 2016 United Technologies Corporation. All rights reserved. Specifications SIGA-270, SIGC- SlGA-2700 Catalog Number 270F, SIGC-270B SIGC-270PB SIGA-278 Description Single Action Single Action -Two Double Action - One Stage Stage (Presignal) - One Stage Addressing Uses 1 Module Uses 2 Module Uses 1 Module Requirements Address Addresses Address Operating Current Standby = 250pA Standby = 396pA cStandby 250pA) Activated = 400ijA Activated = 680ijA 400pAl Construction & Finish Diecast Zinc - Red Epoxy Lexan - Red with with aluminum markings white markings Type Code Factory Set Operating Voltage 15.2 to 19.95 Vdc (19 Vdc nominal) Storage and Operating Operating Temperature: 32"F to 120°F (DC to 49"C) Environment Storage Temperature: -4°F to 140°F (-20"C to 60"C) Humidity: 0 to 93% RH LED Operation On-board Green LED - Flashes when polled On-board Red LED - Flashes w hen in alarm Compatibility Use With: Signature Loop Controller Agency Listings UL, ULC (note 1), MEA, CSFM, FM Note: SIGC-270F SIGC-2 708 and SIGC-270PB are ULC listed only. Suffix °F° indicates French markings. Suffix °B' indicates English/French bi/ing ua! markings. Ordering Information Catalog Ship Wt. Number Description lbs (kg) SIGA-270 One Stage Fire Alarm Station, English Markings - UL/ULC Listed SIGC-270F One Stage Fire Alarm Station, French Markings - ULC Listed SIGC-270B One SlGA-270P Two Stage (Presignal) Fire Alarm Station, English Markings - UL/ULC Listed 1 (0.5) SIGC- Two Stage (Presignal) Fire Alarm Station, French/English Markings 270PB - ULC Listed Double Action (One Stage) Fire Alarm Station, English Markings - ULIULC Listed Accessories 32997 GA Key w/Tag - for pre-signal station (CANADA ONLY) 276-K2 GA Key - for pre-signal station (USA ONLY) 276-Ki Station Reset Key, Supplied with all Key Reset Stations 0 1 05 27165 12 Glass Rods - for SIGA-270 series (CANADA ONLY) 270-GLR 20 Glass Rods - for SlGA-270 series (USA ONLY) J FW.JU - UI 0 Oul lab 276B-RSB Surface Mount Box, Red - for SIGA pull stations 1(0.6) Page 4of4 DATA SHEET E850010279 Not to be used for installation purposes. Issue 1 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. (fl5O-1657:019 Page 1 of 1 CATEGORY: 7150 - FIRE ALARM PULL BOXES LISTEE: EDWARDS, A Division of UTC Fire & Security Americas Corporation, lnc.8985 Town Center Parkway, Bradenton, 34202 United States Contact: Jewell Conover (941) 739-4358 Fax (941) 308-8123 Email: rhonda.conover@fs.utc.com DESIGN: Models SIGA-270, SIGA-270P, andSIGA-278noncoded, intelligent manual pull stations*. Unit consists of a listed pull station and a remote transponder. Refer to listee's data sheet for additional detailed product description and operational considerations. INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating and UL label. APPROVAL: Listed as manual pull stations for use with separately listed compatible fire alarm control units. * These manual pull boxes meet the requirements of UL Standard 38, 1999 Edition with California amendments. NOTE: Formerly 7150-1591:129 and 7150-1388:194 7-29-10 ma ,*r This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2018 Listing Expires (June 30, 2019) Authorized By: DAVID CASTILLO, Program Coordinator Fire Engineering Division ? SIGA-CTI/2 SIGA-MCT2 UiiWdechnnIogie m , oil, EDWARDS Catalog Intelligent Input-Output LIFE SAFETY , INCIDENT MANAGEMENT Input Modules SIGA-CT1, SIGA-CT1 HT, (sIGA-cT2) SIGA-MCT2 3MEA 7300-1657: 0121 S3424 I Overview The SIGA-CT1 Single Input Module, SIGA-CT1 HT High Tem- perature Single Input Module and SIGA-CT2/SIGA-MCT2 Dual Input Modules are intelligent analog addressable devices used to connect one or two Class B normally-open Alarm, Supervisory, or Monitor type dry contact Initiating Device Circuits (IDC). The actual function of these modules is determined by the "persona]- ity code" selected by the installer. This code is downloaded to the module from the Signature loop controller dung system configura- tion. The input modules gather analog information from the initiating devices connected to them and convert it into digital signals. The module's on-board microprocessor analyzes the signal and decides whether or not to input an alarm. The SIGA-CT1, SIGA-CT1 HT and SIGA-CT2 mount to standard North American 1-gang electrical boxes, making them ideal for lo- cations where only one module is required. Separate I/O and data loop connections are made to each module. The SIGA-CT1 HT module operates at an expanded temperature range of 32 "F to 158 "F (0 "C to 70 "C) for those applications requiring more extreme environmental temperature variation. The SIGA-MCT2 is part of the UIO family of plug-in Signature Series modules. It functions identically to the SIGA-CT2, but takes advantage of the modular flexibility and easy installation that characterizes all UlO modules. Two- and six-module UIO mother- boards are available. All wiring connections are made to terminal blocks on the motherboard. UIO assemblies may be mounted in EDWARDS enclosures. Standard Features Multiple applications Including Alarm, Alarm with delayed latching (retard) for water- flow applications, Supervisory, and Monitor. The installer selects one of four "personality codes" to be downloaded to the mod- ule through the loop controller. SIGA-CT1 HT rated for high temperature environments Suitable for attic installation and monitoring high temperature heat detectors. Plug-in (UIO) or standard 1-gang mount UIO versions allow quick installation where multiple modules are required. The 1-gang mount version is ideal for remote loca- tions that require a single module. Automatic device mapping Signature modules transmit information to the loop controller regarding their circuit locations with respect to other Signature devices on the wire loop. Electronic addressing Programmable addresses are downloaded from the loop con- troller, a PC, or the SIGA-PRO Signature Program/Service Tool. There are no switches or dials to set. Ground fault detection by address Detects ground faults right down to the device level. Page lof4 DATA SHEET E850010241 Not to be used for installation purposes. Issue 1 Signature Series Overview The Signature Series intelligent analog-addressable system from EDWARDS Security is an entire family of multi-sensor detectors and mounting bases, multiple-function input and output modules, network and non-network control panels, and user-friendly mainte- nance and service tools. Analog information from equipment con- nected to Signature devices is gathered and converted into digital signals. An onboard microprocessor in each Signature device measures and analyzes the signal and decides whether or not to input an alarm. The microprocessor in each Signature device pro- vides four additional benefits - Self-diagnostics and History Log, Automatic Device Mapping, and Fast, Stable Communication. Self-diagnostics and History Log - Each Signature Series device constantly runs self-checks to provide important mainte- nance information. The results of the self-check are automatically updated and permanently stored in its non-volatile memory. This information is accessible for review any time at the control panel, PC, or using the SIGA-PRO Signature Program/Service Tool. Automatic Device Mapping —The Signature Data Control- ler (SDC) learns where each device's serial number address is installed relative to other devices on the circuit. The SDC keeps a map of all Signature Series devices connected to it. The Signature Series Data Entry Program also uses the mapping feature. With interactive menus and graphic support, the wired circuits be- tween each device can be examined. Layout or "as-built" drawing information showing branch wiring (T-taps), device types and their address are stored on disk for printing hard copy. Installation SIGA-CTI, SIGA-CT1 HT and SIGA-CT2: modules mount to North American 21/2 inch(64 mm) deep 1-gang boxes and 11/2 inch (38 mm) deep 4 inch square boxes with 1-gang covers and SIGA- MP mounting plates. The terminals are suited for #12 to #18 AWG (2.5 mm2 to 0.75 mm2) wire size. Compatible electrical box Wall plate, white (1-gang) • .6' [\ Status LEDs LED viewing ports • SIGA-MCT2: mount the UIO motherboard inside a suitable ED- WARDS enclosure with screws and washers provided. Plug the SlGA-MCT2 into any available position on the motherboard and secure the module to the motherboard with the captive screws. Wiring connections are made to the terminals on the motherboard (see wiring diagram). UIO motherboard terminals are suited for #12 to #18 AWG (2.5 mm2 to 0.75 mm2) wire size. UlO Motherboard 6-32 Self-lapping screws Plug-in 7(UI0) Captive - -- Module lrrews I washers Cabinet or electrical enclosure Electronic Addressing - The loop controller electronically ad- dresses each module, saving valuable time during system com- missioning. Setting complicated switches or dials is not required. Each module has its own unique serial number stored in its on-board memory. The loop controller identifies each device on the loop and assigns a "soft" address to each serial number. If desired, the modules can be addressed using the SIGA-PRO Signature Program/Service Tool. EDWARDS recommends that this module be installed according to latest recognized edition of national and local fire alarm codes. Application The duty performed by the SIGA-CT1 and SIGA-CT2/MCT2 is de- termined by their sub-type code or "Personality Code". The code is selected by the installer depending upon the desired application and is downloaded from the loop controller. One personality code can be assigned to the SIGA-CT1. Two per- sonality codes can be assigned to the SIGA-CT2/MCT2. Codes 1, 2, 3 and 4 can be mixed on SIGA-CT2/MCT2 modules only. For example, personality code 1 can be assigned to the first address (circuit A) and code 4 can be assigned to the second address (circuit B). NORMALLY-OPEN ALARM - LATCHING (Personality Code 1) - Assign to one or both circuits. Configures either circuit A or B or both for Class B normally open dry contact initiating devices such as Pull Stations, Heat Detectors, etc. An ALARM signal is sent to the loop controller when the input contact is closed. The alarm condition is latched at the module. NORMALLY-OPEN ALARM - DELAYED LATCHING (Person- ality Code 2) - Assign to one or both circuits. Configures either circuit A or B or both for Class B normally-open dry contact initiat- ing devices such as Waterfiow Alarm Switches. An ALARM signal is sent to the loop controller when the input contact is closed for approximately 16 seconds. The alarm condition is latched at the module. NORMALLY-OPEN ACTIVE - NON-LATCHING (Personality Code 3) - Assign to one or both circuits. Configures either circuit A or B or both for Class B normally-open dry contact monitoring input such as from Fans, Dampers, Doors, etc. An ACTIVE signal is sent to the loop controller when the input contact is closed. The active condition is not latched at the module. NORMALLY-OPEN ACTIVE - LATCHING (Personality Code 4) - Assign to one or both circuits. Configures either circuit A or B or both for Class B normally open dry contact monitoring input such as from Supervisory and Tamper Switches. An ACTIVE signal is sent to the loop controller when the input contact is closed. The active condition is latched at the module. Page 2of4 DATA SHEET E850010241 Not to be used for installation purposes. Issue I UL/ULC Listed 01fEO UdJLCUNtOd OIKWEOL ri r LiLi1 V.*mEpj series Ott. n+91 11717-4 A slgnafU,O T. Noaaoecnl005,eq,ired fir DOt 2 MCT2 oirvt Ii + 4J TB? Othnrnnidotnnnnoy,nqoon D0t0OIJt — — 001ineors. Fted LM Me=7W, (Lii ls conn2000n, o,ionpnrNnningn rfo,rnd for PICTS. SlGA-MCT2 Typical Wiring Modules will accept #18 AWG (0.75mm2), #16 (1 .Omm2), and #14AWG (1.50mm2), and #12 AWG (2.50mm2) wire sizes. Note: Sizes #16 AWG (1.0mm2) and #18 AWG (0.75mm2) are preferred for ease of installation. See Signature Loop Controller catalog sheet for detailed wiring requirement specifications. Initiating (Slave) Device Circuit Wire Specifications Maximum Allowable Wire Resistance 50 ohms (25 ohms per wire) per Circuit Maximum Allowable Wire Capacitance 0.1ijF per Circuit For Design Reference: Wire Size I Maximum Distance to EOLR #18 AWG (0.75 mm2) #16 AWG (1.00 mm2) 4,000 ft(1 219 m) #14 AWG (1.50 mm2) I #12 AWG (1.50 mm2) I Typical N.C. Initiating Device Typical N.O. Initiating Device INPUT 1 INPUT 2 AAASM. B (Cl.. B) 8 B2 ILED _ 47 EOL UULC Uxted 8 7 UL/ULC Usted 471(L) EOL 471(0 EOL UL/ULC listed Green LED (Normal) Ted ___ _______________ Ped LED __ _____________ Green LED (Alarm/Active) (Jarm/ 2 1 (Normal) TB1 ID1lXflh1 f DATA IN(+)> 1 DATA IN(-) From Signature Controller or Previous Device SlGA-CT1, SlGA-CT1 HT (DATA IN (+)! DATA DATA OUT (+)} . DATA IN C-)> y I p DATA OUT (+)} DATA OUT C-) To Nest Device From Signature Controller To Next Device or Previous Device A SlGA-CT2 I Typicol NO Initiothrg 520102 1 1 NOTES Maximum 25 Ohm resistance per wire. Maximum #12 AWG (2.5 mm2 ) wire; Minimum #18 AWG (0.75 mm2). Refer to Signature controller Installation sheet for wiring specifications. Maximum 10 Vdc @ 350 pA The SIGA-U106R and the SIGA-U102R do not come with T814. 6 All wiring is supervised and power-limited. 7 These modules will not support 2-wire smoke detectors. Warnings & Cautions This module will not operate without electrical power. As fires fre- quently cause power interruption, we suggest you discuss further safeguards with your local fire protection specialist. Compatibility These modules are part of EDWARDS's Signature Series intelligent processing and control platform. They are compatible with EST3, EST3X and iO Series control panels. Page 3of4 DATA SHEET E850010241 Not to be used for installation purposes. Issue 1 LIFE SAFETY & INCIDENT MANAGEMENT Contact us... Email: edwards.fire@fs.utc.com Web: Edwards-fire.com EDWARDS is a UTC brand. 1016 Corporate Park Drive Mebane, NC 27302 © 2016 United Technologies Corporation. All tights reserved. Specifications Catalog Number SIGA-CT1 HI I SIGA-CT1 fiGA-C2 I SIGA-MCT2 Description Single Input Module Dual Input Module Type Code 48 (factory set) Four sub-types (personality codes) are available 49 (factory set) Four sub-types (personality codes) are available Address Requirements Uses One Module Address Uses Two Module Addresses Operating Current Standby = 250pA; Activated = 400pA çStdby 396pATJ ctivate.F6OlJP Operating Voltage 15.2 to 19.95 Vdc (19 Vdc nominal) Construction High Impact Engineering Polymer Mounting North American 21/2 inch (64 mm) deep one-gang box- es and 11/2 inch (38 mm) deep 4 inch square boxes with one-gang covers and SIGA-MP mounting plates U102R/6R/6 Motherboard Operating Environment 32°F to 158°F (0°C to 70°C) to Storage Environment -4°F to 140°F (-20°C to 60°C); Humidity: 0 to 93% RH LED Operation On-board Green LED - Rashes when polled; On-board Red LED - Flashes when in alarm/active. Compatibility Use with Signature Loop Controller Agency Listings UL ULC, MEA, CSFM Ordering Information Catalog Description Ship Wt. Number lbs (ka) SlGA-CT1 HT Single Input Module High Temperature Operation ULJULC Listed 0.4 (0.15) ISIGACT2) Dual Inout Module - ULJULC Listed 0.4(0.15) SIGA-MCT2 Dual In Related Equipment 27193-11 Surface Mount Box - Red, 1-gang 1.0(0.6) 27193-16 Surface Mount Box - White, 1-gang 1.0(0.6) SIGA-UlO2R Universal Input-Output Module Board w/Riser Inputs 0.32 (0.15) - Two Module Positions SIGA-UI06R Universal Input-Output Module Board w/Riser Inputs 0.62 (0.28) - Six Module Positions SlGA-Ul06 Universal Input-Output Module Board - Six Module Positions 0.56 (0.25) MFC-A Multifunction Fire Cabinet - Red, supports Signature Module 7.0(3.1) Mounting Plates SlGA-MB4 Transponder Mounting Bracket (allows for mounting 0.4 (0.15) two 1-gang modules in a 2-gang box) SIGA-MP1 Signature Module Mounting Plate, 1 footprint 1.5 (0.70) SlGA-MP2 Signature Module Mounting Plate, 1/2 footprint 0.5 (0.23) SlGA-MP2L Signature Module Mounting Plate, 1/2 extended footprint 1.02 (0.46) Page 4 of 4 DATA SHEET E85001-0241 Not to be used for installation purposes. Issue 1 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE L) LISTING No. (7300-1657:012) Page I of I CATEGORY: 7300 - FIRE ALARM CONTROL UNIT ACCESSORIES/MISC. DEVICES LISTEE: EDWARDS, A Division of UTC Fire & Security Americas Corporation, Inc.8985 Town Center Parkway, Bradenton, 34202 United States Contact: Jewell Conover (941) 739-4358 Fax (941) 308-8123 Email: rhonda.conover@fs.utc.com DESIGN: Models SIGA-CC1, SIGA-CC2, SlGA-CTI, SlGA-CTI HT,(GA-CT2) SIGA-CR, SIGA-CRR, SIGA-UM, SlGA-MMI, SlGA-WTM, SIGA-IM, SIGA-MDM, SIGA-MAB, SlGA-MCT2, SIGA-MCCI, SIGA-MCC2, SlGA-MCR and SIGA-MCRR remote transponders. Models SIGA-AA30 and SIGA-AASO audio amplifiers. Models SIGA-APS and SIGA-APS-220 power supplies. Models SIGA-MB4, SIGA-MPI, SIGA-MP2 and SIGA-MP2L mounting plates. Models SIGA-UlO2R, SIGA-U106 and SIGA-U106R motherboards. Model CS-SIGA-CCIP releasing module. Models SIGA-CCIS and SIGA-MCCIS Auto-Sync Output Modules. Models MFG-A and MFC-AD Enclosures. Model SIGA-CR2 Control Relay Module. Model SlGA-CT1 HT; Signature Series High Temperature Single Input Module. *SIGA..CRH High Power Control Relay Module. Refer to listee's data sheet for additional detailed product description and operational consideration. RATING: 15.2 - 19.95 VDC INSTALLATION: In accordance with listee's printed installation instructions, applicable codes & ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating, and UL label. APPROVAL: Listed as control unit accessories for use with separately listed compatible fire alarm control units. Refer to listee's Installation Instruction Manual for details. NOTE: Formerly 7300-1591:121 and 7300-1388:178 *Rev 01-11-16 gt 0 This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2018 Listing Expires (June 30, 2019) Authorized By: DAVID CASTILLO, Program Coordinator Fire Engineering Division EDWARDS Catalog Strobes, Horns, Bells, Chimes 'Z LIFE SAFETY §' INCIDENT MANAGEMENT Fire Alarm Bells MEA S218, S2202 * 7136-1657 0150 Overview Standard Features Vibrating and single stroke 6 inch (150mm), 8 inch (200mm), 10 inch (250mm) sizes Red or gray finish Rugged compact mechanism Heavy duty cast housing Low power drain Wide voltage selection Indoor or weatherproof EDWARDS Fire Alarm Bells are specially designed for fire alarm applications. The gongs are made of selected alloy steel to give the loud, resonant tones necessary in fire alarm systems. Two gong sizes are available to overcome different ambient noise level. The Fire Alarm Bells are of the underdome type with heavy duty mechanisms. Each bell is supplied with a mounting plate that fits any standard single-gang opening (see Installation Data). For weather-proof application EDWARDS offers an optional surface weatherproof back box. Refer to the Specification chart for ap- plicability and cata-log number of the weatherproof back box for the respective bell. Finish - Standard gong and housing furnished gray with red label. Optional red finish available. Add Suffix "R" to Catalog Number. FM - 438 and 439 Series Bells shown below are FM approved. Page 1 of 2 DATA SHEET E85001-0333 Not to be used for installation purposes. Issue 1 LIFE SAFETY & INCIDENT MANAGEMENT Contact us... Email: edwards.fire@fs.utc.com Web: Edwards-fire.com EDWARDS is a UTC brand. 1016 Corporate Park Drive Mebane, NC 27302 © 2016 United Technologies Corporation. All rights reserved. Installation Cat. Nos. 438D and 4390 6" and 10" Bells / \ 10 DIP.. GONG -J, I 10' OIA. GONG / (500mm) I (2501rnN / 41le)a4.sE) . (117mm) -1 (178mm) 6 001 GONG -i--i nWLL j (150lm1) 0 )_11 ~C' MOUNTING PLATE (FURNISHED) (74M-) —1 MOUNTS DIRECTLY ON SURFACE OR ANY SINGLE GANG OPENING, 340', 4 OCTAGON. 4 SO. BOX OR CAT. L31sIa NO. 449 WEATHERPROOF WALL BOX. OUTLET 11A6 (17$mm) CAT NO 449 ii WEATHER- I' 1/ PROOF BOX- (PAINTED GRAY) ULJ OUTLET 16' I 3I4 (143mm) 6' OIA. (1501 OF SASI Cat. Nos. 3230 and 10' (254mm) Bells 4. r'(l02mnm) I I-3-9lI6 (I76m.n) (76mm)1 6 DIAL GON (150mm) I I 7- (175mm) 10'DIA.GONG ,. I _- (250mm) WARNING: These devices will not op- erate without electrical power. As fires frequently cause power interruptions, we suggest you discuss further safeguards with your local fire protection specialist. EDWARDS recommends that these Fire Alarm Bells always be installed in accord- ance with the latest recognized editions of national and local codes. Specifications & Ordering Information DB@ Weatherproof Cat. No. Description Volts Amps Box lOft 323D-10AW-R 79 10" (250mm) 20-24 Vdc 0.33 N/A Single Stroke, Diode 438D-6N5-R 76 6° (150mm) 120 Vac 0.034 449 Vibrating, Diode 438D-10N5-R 88 10° (250mm) 120 Vac 0.034 449 Vibrating, Diode 439D-6AW-R 83 6' (150mm) 20-24 Vdc 0.085 449 Vibrating, Diode P.10AW) 86 10° (250mm) 20-24 Vdc 0.085 449 Vibrating, Diode 438D-8N5-R 86 8° (200mm) 120 Vac 0.034 449 Vibrating, Diode 439D-8AW-R 84 8° (200mm) 20-24 Vdc 0.085 449 Vibrating, Diode 439D-6AWC-R 83 6° (150mm) 20-24 Vdc 0.085 449 Vibrating, Diode, ULC listed 439D-10AWC-R 86 10" (250mm) 20-24 Vdc 0.085 449 Vibrating, Diode, ULC listed Mounting Accessories 49) Weatherpoof surface mount box, grey. C/w gasket. Page 2of2 DATA SHEET E850010333 Not to be used for installation purposes. Issue 1 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. (7136-1657:0150 Page 1 of I CATEGORY: 7136 —AUDIBLE DEVICES FOR HAZARDOUS LOCATIONS LISTEE: EDWARDS, A Division of UTC Fire & Security Americas Corporation, lnc.8985 Town Center Parkway, Bradenton, 34202 United States Contact: Jewell Conover (941) 739-4358 Fax (941) 308-8123 Email: rhonda.conover@fs.utc.com DESIGN: Models 325, 340, 340T, 343, 438, 439, 4390 series and explosion-proof Models CS2315, C52316 and 340DEX, 435DEX, 438DEX, 439DEX series vibrating bells. Models 325, 340, 340T, 343, 438, 439,D may be used outdoors when used with a weatherproof box. Refer to listee's data sheet for detailed model description and operational considerations. INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating, hazardous location classification (if applicable) and UL label. APPROVAL: Listed as audible devices for use with separately listed compatible control units. Explosion-proof models intended for use in Class I, Groups B,C,D; Class II, Groups E,F,G hazardous locations. If this appliance is required to produce a distinctive three-pulse Temporal Pattern Fire Alarm Evacuation Signal (for total evacuation) in accordance with NFPA 72, 2002 Edition, the appliance must be used with a fire alarm control unit that can generate the temporal pattern signal. Refer to manufacturer's Installation Manual for details. NOTE: Formerly 7136-1591:150, 7135:1591:150, 7135-1388:110, 7135-0073:032 7-29-10 ma This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions 'and/or other Date Issued: July 01, 2018 Listing Expires [June 30, 201!) Authorized By: DAVID CASTILLO, Program Coordinator Fire Engineering Division