HomeMy WebLinkAbout3262 GREY HAWK CT; ; AS1100057/15/24, 4:55 PM AS110005 Permit Data
City of Carlsbad
Sprinkler Permit
Job Address: 3262 GREY HAWK CT
Permit Type: SPRINK
Parcel No: 2210150722
Lot #: 0
Permit No: ASII0005
Status: ISSUED
Applied 1/12/2011
Approved: 1/12/2011
Reference No.: Issued: 1/12/2011
PC #: Inspector:
Project Title: 2GIG TECHNOLOGIES T.I. FIRE SPRINKLER PLAN CHECK &
INSPECTIONS
Applicant:
TATE FIRE PROTECTION SERVICES, INC
STEC
13691 DANIELSON ST
POWAY, CA
Owner:
GREYHAWK ASSOCIATES
C/O RUDY BALDONI
949 S COAST DR #600
COSTA MESA CA
Fees ($) Add'I Fees ($) Total ($) Balance ($)
130 0 130 0
about:blank 1/1
TATE FIRE
I PROTECTION SERVICES INC.
DATE: 12/2/10
PROJECT: 2G1G Technologies
3262 Grey Hawk Court
Carlsbad, CA 92010
JOB NUMBER: S-10-0149
GENERAL CONTRACTOR: Jacor Construction
FIRE SPRINKLER MODIFICATION MATERIAL SUBMITTAL
Page Product
1-2 Sprinkler Piping
3-10 Sprinkler Piping
11-12 Sprinkler Piping
13-19 Sprinkler
20-23 Sprinkler
24 Pipe Hangers & Supports
25 Pipe Hangers & Supports
26-27 Pipe Hangers & Supports
Descriotion
ALLIED Dyna Thread Pipe
TYCO Ductile Iron Fittings
TYCO Mechanical Tee
TYCO TY-FRB Q.R. SSP
TYCO RF-II Q.R. SSP
AFCON Fig 300 Ring
AFCON Fig 655 All Thread Rod
SAMMY Wood Screw
13691 Danielson Street Suite C - Poway, CA 92064 f. 858-486-0900 - f. 858-486-0950 California C 16/Cl 0 License # 926322
DynamThread 0
Full Line Sch-40 Replacement
Dyna-Thread offers the life expectancy of Sch40 with superior hydraulics and greater value.
Dyna-Thread sprinkler pipe represents an engineering advancement for the sprinkler pipe industry. It combines the safety
and longevity of traditional Sch-40 pipe with quality and superior hydraulic advantages.
Dyna-Thread's inside diameter is up
to 3.6% larger than Sch-40 giving it
superior hydraulics. And, when used
in combination with Dyna-Flow pipe,
down sizing often occurs.
Dyna-Thread is fully listed and
approved by UL, ULC, and FM for
fire sprinkler applications.
The life expectancy of Dyna-Thread
and Sch-40 are equal based on the
calculated wall thicknesses per UL.
The consistent quality of steel used to
make Dyna-Thread facilitates smooth
threading and lower maintenance
costs.
The exterior of Dyna-Thread is
protected by a clean, durable mill
coating for extended shelf life and
easy paint application.
(9 <~> (q~
Listed Approved Listed
With its increased strength and lighter
weight, Dyna-Thread reduces
installation fatigue and is ideal for
retro-fit applications.
Corrosion Resistance Ratio (CRR) is a
UL (Underwriters Laboratory) term for
the estimated life expectancy of a pipe
joint. This is based on the calculated
wall thickness at the base of the first
exposed thread, assumed to be the
weakest point of the pipe length. Dyna-
Threadand Sch-40 have the same
calculated wall thicknesses at this point
and are both assigned the same CRR of
1.00.
The internal surface of all black Allied
Tube & Conduit Fire Sprinkler pipe
products up to 4.5000" in diameter is
coated with our new Antibacterial
Formula, "ABF". In scientific laboratory
test, ABS proved to have superior
resistance to microbial colonization of
pipe walls, thereby delaying or possibly
preventing the onset of
Microbiologically Influenced corrosion
(MIC) when the First Sprinkler System
is first installed.
More wall thickness at the thread
(CRR'' 1.00) gives Dyna-Thread
better life expectancy than lightwall
threadable pipe joints.
Unlike lightwall threadable pipe,
Dyna-Thread has no thread gauge
warning.
Dyna-Thread is approved for
standard hanger spacing (15 ft.
O.C.), can be used as earthquake
sway bracing, and is safe to use as
drops.
Dyna-Thread is safer to weld on.
Dyna-Thread is more widely
accepted than lightwall threadable
where Sch-40 is specified.
Super 40/Dyna-Thread pipe is
manufactured to meet: ASTM A- 135,
Grade A and is in compliance with
NFPA- 13. All sizes of Super 40/Dyna-
Thread are rated at 300 psi working
pressure. Super 40/Dyna-Thread is UL
and ULC Listed for wet, dry deluge and
pre-action sprinkler systems and FM
Approved for use in wet systems. Super
40/Dyna-Thread can be "hot-dip"
galvanized to meet FM requirement for
dry systems. Super 40/Dyna-Thread is
approved for all threaded couplings and
welded outlets and is suitable for all
roll-grooved, and plain-end fittings.
(See listing information).
Specifications
NPS Nominal I.D. WI. WI. (H20 Filled) Pcs/ WI/Lift (21) WI/Lift (24) WI/Lift (25)
In; mm In; mm Lbs/Ft; Kg/rn Lbs/Ft; Kg/rn Lift Lbs; Kg Lbs; Kg Lbs; Kg
ill 1.080 1.330 1.75 70 1955 2234 2327
25 27.4 2.0 2.60 70 887 1013 105
11/4" 1.408 1.870 2.54 51 2002 2288 2384
32 35.8 2.8 3.78 51 908 1038 1081
11/2 1.639 2.290 3.22 44 2115 2418 2519
40 41.6 3.4 4.79 44 959 1097 114
2 2.104 3.050 4.57 30 1921 2196 2287
50 53.4 4.5 6.80 30 871 996 103
.1 16100 S. Lathrop• Harvey, IL 60426 tqco/Flow control Qffltj 11350 Norcom Rd. Philadelphia, PA 19154
TUBE & CONDUIT 2525 N. 27 th Ave. Phoenix, AZ 85009
Customer Service:
(800) 882-5543
Fax 708339180___1
S3 -3
Submittal Data Sheet
Dyna-Th read®
Full Line Sch-40 Replacement
Dyna-Thread sprinkler pipe represents an engineering advancement for the sprinkler
pipe industry. It combines the safety and longevity of traditional Sch-40 pipe with
quality and superior hydraulic advantages.
Comparison to Schedule 40 Dyna-Threads inside diameter is up to 3.6% larger than
Sch-40 giving it superior hydraulics. Also, when used in combination with Dyna-Flow
pipe, down sizing often occurs. Dyna-Thread is fully listed and approved UL, ULC,
and FM for fire sprinkler applications. The life expectancy of Dyna-Thread and Sch-40
are equal based on the calculated wall thicknesses per UL. The consistent quality of
steel used to make Dyna-Thread facilitates smooth threading and lower maintenance
costs. The exterior of Dyna-Thread is protected by a clean, durable mill coating for
extended shelf life and easy paint application. With its increased strength and lighter
weight, Dyna-Thread reduces installation fatigue and is ideal for retro-fit applications.
Corrosion Resistance Ratio (CRR) is a UL (Underwriters Laboratory) term for the
estimated life expectancy of a pipe joint. This is based on the calculated wall thickness
at the base of the first exposed thread, assumed to be the weakest point of the pipe
length. Dyna-Thread and Sch-40 have the same calculated wall thicknesses at this
point and are both assigned the same CRR of 1.00.
Comparison to L.W.T. Pipe More wall thickness at the thread (CRR= 1.00) gives
Dyna-Thread better life expectancy than lightwall threadable pipe joints. Unlike
lightwall threadable pipe Dyna-Thread has no thread gauge warning. Dyna-Thread is
approved for standard hanger spacing (15 ft. O.C.), can be used as earthquake sway
bracing, and is safe to use as drops. Dyna-Thread is safer to weld on than many zinc-
coated lightwall threadable pipe products. Dyna-Thread is more widely accepted than
lightwall threadable where Sch-40 is specified.
Stamp Here
Specifications & Approvals Super 40/
Dyna-Thread pipe is manufactured to
meet: ASTM A 135, Grade A and is in
compliance with NFPA-13. All sizes of
Super 40/Dyna-Thread are rated at 300
psi working pressure. Super 40/ Dyna-
Thread is UL and ULC Listed for wet,
dry and pre-action sprinkler systems and
FM Approved for use in wet systems.
Super 40/Dyna-Thread can be "hot-dip"
galvanized to meet FM requirement for
dry systems. Super 40/Dyna-Thread is
approved for all threaded couplings and
welded outlets and is suitable for all roll-
grooved, and plain-end fittings. (See
listing information).
The internal surface of all black Fire
Sprinkler pipe up to 4.5000" in diameter
shall be coated with Allied Tube &
Conduit Antibacterial Formula "ABF".
Specifications
NPS Nominal I.D. WI. WI. (H20 Filled) Pcs/ Wt/Lift (21l') WtI1.ift (24) WI/l.ift (25)
In; mm In; mm Lbs/Ft; Kg/rn Lbs/Ft; Kg/rn Lift Lbs; Kg Lbs; Kg Lbs; Kg
ill 1.080 1.330 1.75 70 1955 2234 2327
25 27.4 2.0 2.60 70 887 1013 105
11/4 1.408 1.870 2.54 51 2002 2288 2384
32 35.8 2.8 3.78 51 908 1038 108
11/2 1.639 2.290 3.22 44 2115 2418 2519
40 41.6 3.4 4.79 44 959 1097 114
2 2.104 3.050 4.57 30 1921 2196 2287
50 53.4 4.5 6.80 30 871 996 103;
American Tube and Pipe was acquired by Allied Tube and Conduit on February 1,
1997. The engineered lightwall and standard wall family of products although they
have different names are the same in all respects with regard to strength, weight,
bundle count, listings and approvals. For example,
Dyna-Flow and Super Flo are the same product as
are Dyna Thread and Super 40. XL is manufactured Ue L ffj
with Exterior galvanized coating. BLT is
manufactured with Black lacquer coating. Listed Approved Listed
2G1G Technologies Tate Fire Protection 12/2/10
Project: Sprinkler Contractor: Date:
Engineer: Specification Reference: System Type:
Locations: Comments:
S3-4
tqCU /Fire & Building
/ )Products
Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500
Pipe Fittings
NPT Threaded,
Ductile Iron
General
Description
The Tyco® Series 800 Threaded Pipe
Fittings and California Tees & Elbows
are manufactured from ductile iron.
They are stronger and more corrosion
resistant than cast iron fittings. The
additional strength is provided by the
ductile properties and by adding mag-
nesium while the iron is being poured
into the final cast shape. Although
lighter than standard cast iron, the fit-
tings have an added advantage of be-
ing less susceptible to cracking due to
their added strength.
The Series 800, California, and Figure
719 Threaded Pipe Fittings are a re-
designation for the Central Series 800,
California, and Figure 719 Threaded
Pipe Fittings.
WARNINGS
The Threaded Pipe Fittings described
herein must be installed and main-
tained in compliance with this docu-
ment, -as well as with the applicable
standards of the National Fire Pro-
tection Association, in addition to the
standards of any other authorities hav-
ing jurisdiction. Failure to do so may
impair the performance of these
devices.
The owner is responsible for maintain-
ing their fire protection system and de-
vices in proper operating condition.
The installing contractor or sprinkler
manufacturer should be contacted
with any questions.
Technical
Data
Approvals:
UL Listed and FM Approved
Maximum Working Pressure:
Series 800 and California Fittings
250 psi (17,2 bar)
Figure 719 Plug:
250 psi (17,2 bar)
Material:
Series 800 and California Fittings:
Ductile Iron
Figure 719 Plug:
Cast Iron
Pipe Thread:
NPT per ANSI 131.20.1
Installation
Apply Teflont tape or high quality pipe
joint compound on male pipe threads
and tighten two to three turns beyond
hand tight.
NOTE
Installers who have not used ductile
iron threaded fittings should be in-
structed that the fittings are stron-
ger than the pipe and overtightening
the fitting can create leaks and cause
damage to pipe threads. In general,
there is about one-half turn difference
between cast iron and ductile iron fit-
tings. Apply Teflon tape or high qual-
ity pipe joint compound on the male
pipe threads and tighten two to three
turns beyond hand tight. If an auto-
matic make-on machine is being used,
please exercise caution in setting the
machine to the proper parameters pri-
or to tightening fittings onto the male
pipe threads.
Limited
Warranty
Products manufactured by Tyco Fire
& Building Products (TFBP) are war-
ranted solely to the original Buyer for
ten (10) years against defects in mate-
rial and workmanship when paid for
and properly installed and maintained
under normal use and service. This
warranty will expire ten (10) years from
date of shipment by TFBP. No warran-
ty is given for products or components
manufactured by companies not af-
filiated by ownership with TFBP or for
products and components which have
been subject to misuse, improper in-
stallation, corrosion, or which have not
been installed, maintained, modified or
repaired in accordance with applicable
Standards of the National Fire Protec-
tion Association, and/or the standards
of any other Authorities Having Juris-
diction. Materials found by TFBP to be
defective shall be either repaired or re-
placed, at TFBP's sole option. TFBP
neither assumes, nor authorizes any
person to assume for it, any other ob-
ligation in connection with the sale of
products or parts of products. TFBP
shall not be responsible for sprinkler
system design errors or inaccurate or
incomplete information supplied by
Buyer or Buyer's representatives.
In no event shall TFBP be liable, in
contract, tort, strict liability or under
any other legal theory, for incidental,
indirect, special or consequential dam-
ages, including but not limited to labor
charges, regardless of whether TFBP
was informed about the possibility of
such damages, and in no event shall
TFBP's liability exceed an amount
equal to the sales price.
The foregoing warranty is made in lieu
of any and all other warranties, ex-
press or implied, including warranties
of merchantability and fitness for a
particular purpose.
This limited warranty sets forth the ex-
clusive remedy for claims based on
failure of or defect in products, materi-
als or components, whether the claim
is made in contract, tort, strict liability
or any other legal theory.
This warranty will apply to the full ex-
tent permitted by law. The invalidity,
in whole or part, of any portion of this
warranty will not affect the remainder.
Ordering
Procedure
When placing an order, indicate the
full product name. Please specify the
quantity, figure number, wall thickness,
and size.
registered trademark of F. I. du Pont de
Nemours and Company or its affiliates.
TFPI7IO Page 1 of 10 JANUARY, 2008
Page 2oflO TFPI7I0
_(fL T$/N '
Lw--
FIGURE 811 FIGURE 813
900 ELBOW 45° ELBOW
Nominal Pipe
Size Figure 811
ANSI A B Approx. A B
Inches Inches Inches Weight Part Inches Inches
DN (mm) (mm) Lbs. Number (mm) (mm) (kg)
1/2 1.13 0.56 0.24 86206 0.88 0.38
DN15 (28,7) (14,2) (0,11) (22,4) (9,7)
3/4 1.31 0.75 0.40 86205 1.00 0.44
DN20 (33,3) (19,0) (0,18) (25,4) (11,2)
1 1.50 0.81 0.64 86200 1.13 0.81
DN25 (38,1) (20,6) (0,29) (28,7) (20,6)
1-1/4 1.75 1.06 0.95 86201 1.31 0.63
DN32 (44,5) (26,9) (0,43) (33,3) (16,0)
1-1/2 1.94 1.19 1.24 86202 1.44 0.69
DN40 (49,3) (30,2) (0,56) (36,6) (17,5)
2 2.25 1.50 1.74 86203 1.68 0.94
DNSO (57,1) (38,1) (0,79) (42,7) (23,9)
2-1/2 2.69 1.56 3.28 86204 1.94 1.00
DN65 (68,3) (39,6) (1,49) (49,3) (25,4)
TABLE I
NOMINAL DIMENSIONS FIGURES 811 & 813
(D
Figure 813
Approx.
Weight Part
Lbs. Number
(kg)
0.22 86780 (0,09)
0.33 86781 (0,15)
0.48 86280 (0,21)
0.73 86281 (0,33)
0.93 86282 (0,42)
1.55 86283 (0,70)
2.70 86782 (1,22)
TFPI7IO Page 3 of 10
FIGURE 812
900 REDUCING ELBOW
Nominal Pipe Figure 812 Size
ANSI A B C D Approx.
Inches Inches Inches Inches Inches Weight
Lbs.
Part
DN (mm) (mm) (mm) (mm) Number
(kg)
3/4 x 1/2 1.19 1.19 0.63 0.63 0.33 86342 DN20x15 (30,2) (30,2) (16,0) (16,0) (0,15)
1 x 1/2 1.25 1.38 0.56 0.81 0.44 86210 DN25x15 (31,8) (35,1) (14,2) (20,6) (0,20)
I x3/4 1.38 1.44 0.69 0.88 0.53
DN25x20 (35,1) (36,6) (17,5) (22,4) (0,24) 86211
1-1/4 x 1/2 1.31 1.50 0.63 0.94 0.64 86212 DN32 x 15 (33,3) (38,1) (16,0) (23,9) (0,29)
1-1/4x3/4 1.44 1.63 0.75 1.06 0.75 86213 DN32x20 (36,6) (41,4) (19,0) (26,9) (0,34)
1-1/4 x 1 1.56 1.68 0.88 1.00 0.77 86214 DN32 x 25 (39,6) (42,7) (22,4 (25,4) (0,35)
1-1/2x3/4 1.50 1.75 0.75 1.19 0.95 86221 DN40x20 (38,1) (44,4) (19,0) (30,2) (0,43)
1-1/2x 1 1.63 1.81 0.88 1.13 0.99 86215 DN40x25 (41,4) (46,0) (22,4) (28,7) (0,45)
1-1/2x1-1/4 1.81 1.88 1.13 1.19 1.14 86216 DN40 x 32 (46,0) (47,8) (28,7) (30,2) (0,52)
2x3/4 1.63 1.94 0.88 1.38 1.39 86217 DN50x20 (41,4) (49,3) (22,4) (35,1) (0,63)
2x1 1.75 2.06 2.00 1.31 1.58 86218 DN50x25 (44,4) (523) (50,8) (33,3) (0,72)
2 x 1-1/2 2.00 2.19 1.25 1.44 1.67
DN50x40 (50,8) (55,6) (31,8) (36,6) (0,76) 86220
2-1/2x2 2.38 2.63 71,251.88 3.01 86262 DN65x50 (60,5) (66,8) ((47,8) (1,36) 1
TABLE 2
NOMINAL DIMENSIONS FIGURE 812
0
TFPI7IO Page 5 of 10
FIGURE 814 FIGURE 818
IRON TEE STRAIGHT COUPLING
Nominal Pipe
Size Figure 814 Figure 818
A B Approx. A B Approx.
ANSI Inches Inches Inches Weight Part Inches Inches Weight Part
DN (mm) (mm) Lbs. Number (mm) (mm) Lbs. Number
(kg) (kg)
1/2 1.13 0.56 0.33 86340 1.38 0.31 0.18 72779 DN15 (28,7) (142) (0,15) (351) (7,9) (0,08)
3/4 1.31 0.75 0.50 86341 1.63 0.56 0.26 72778 DN20 (33,3) (19,0) (0,23) (41,4) (14,0) (0,11)
1 1.50 0.81 0.85 86230 1.75 0.38 0.44 72755 DN25 (38,1) (20,6) (0,38) (44,4) (9,7) (0,20)
1-1/4 1.75 1.06 1.30 86231 2.00 0.56 0.54 72754 DN32 (44,4) (26,9) (0,59) (50,8) (14,0) (0,24)
1-1/2 1.94 1.19 1.63 86232 2.19 0.75 0.71 72753 DN40 (49,3) (30,2) (0,74) (55,6) (19,0) (0,32)
2
DN50
2.25
(57,1)
1.50
(38,1)
2.63
(1,19) 86233 2.63
(66,8)
1.13
(28,7)
1.15
(0,52) 72752
2-1/2 2.69 1.56 4.55 86234 3.00 0.75 2.29 72758 DN65 (68,3) (39,6) (2,06) (76,2) (19,0) (1,04)
__
TABLE 4
NOMINAL DIMENSIONS FIGURES 814 & 818
C
TFPI7I0 Page 6of 10
Page 7 of 10 TFPI7IO
H 11C7
FIGURE 815
REDUCING TEE
Nominal Pipe Size Figure 815
A B C D E F Approx.
ANSI Inches Weight Part Inches Inches Inches Inches Inches Inches DN (mm) (mm) (mm) (mm) (mm) (mm) Lbs. Number
(kg)
1-1/2 x 1-1/4 x 1/2 1.44 1.31 1.69 0.69 0.63 1.13 1.03
DN40 x 32 x 15 (36,6) (33,3) (42,9) (17,5) (16,0) (28,7) (0,47) 86257
1-112x1-1/4x3/4 1.50 1.44 1.75 0.75 0.75 1.19 1.10
DN40x32x20 (38,1) (36,6) (44,5) (19,0) (19,0) (30,1) (0,50)
86258
1-1/2x1-1/4x1 1.63 1.56 1.81 0.88 0.88 1.13 1.31
DN40x32x25 (41,4) (39,7) (46,0) (22,4) (22,4) (28,7) (0,59) 86259
1-1/2x1-1/4x2 2.19 2.13 2.00 1.44 1.44 1.25 1.94
DN40x32x50 (55,6) (54,1) (50,8) (36,6) (36,6) (57,1) (0,88) 86260
1-1/2 x 1-1/2 x 1/2 1.44 1.44 1.69 0.69 0.69 1.13 1.14
DN40 x 40 x 15 (36,6) (36,6) (42,9) (17,5) (17.5) (28,7) (0,52) 86261
1-1/2x1-1/2x3/4 1.50 1.50 1.75 0.75 0.75 1.19 1.23
DN40x40x20 (38,1) (38,1) (44,4) (19,0) 0,1) (0,56)
86262
1-1/2x1-1/2x1 1.63 1.63 1.81 0.88 0.88 13 1.38
DN40x40x25 (41,2) (41,2) (46,0) (22.4) (22,4),7) (0,62) 86263
1-1/2x1-1/2x1-1/4 1.81 1.81 1.88 1.06
(19,0)r28
1.06 19 1.50
DN4O x 40 x 32 (460) (46,0) (47,6) (27,0) (27,0)01) 86264
-1/2x1-1/2x2 2.19 2.19
(0,68)
1 2.00 1.44 1.44 25 2.00
DN4O x 40 x 50 (55,5) (55,5) (50,8) (36.6) (36,6) 1,7) (0,91) 86265
2 x 1 x 2 2.25 2.00 2.25 1.50 1.31 1.50 2.18
DN50x25x50 (57,2) (50,8) (57,2) (38,1) (33,3) (38,1) (0,99) 86266
2 x 1-1/4 x 2 2.25 2.13 2.25 1.50 1.44 1.50 2.31
DN50x32x50 (57,2) (54,1) (57,2) (38,1) (36,6) (38,1) (1,05) 86267
2 x 1-1/2 x 1/2 1.50 1.44 1.88 0.75 0.69 1.31 1.50
DN50 x 40 x 15 (38,1) (36,6) (47,8) (19,0) (17,5) (33,3) (0,68)
86268
2x1-112x3/4 1.63 1.50 1.94 0.88 0.75 1.38 1.61
DN50x40x20 (41,4) (38,1) (49,3) (22,4) (19,0) (35,0) (0,73) 86269
2 x 1-1/2 x 1 1.75 1.63 2.00 1.00 0.88 1.31 1.65
DN50x40x25 (44,5) (41,4) (50,8) (25,4) (22,4) (33,3) (0175)
86270
2x1-1/2x1-1/2 2.06 1.94 2.19 1.31 1.19 1.44 2.03
DN50x40x40 (52,4) (49,2) (55,5) (33,3) (30,2) (36,6) (0,92) 86272
2 x 1-1/2 x 2 2.25 2.19 2.50 1.50 1.44 1.50 2.37
DN50x40x50 (57,1) (55,5) (63,5) (38,1) (36,6) (38,1) (1,07)
86273
2x2x1/2 1.50 1.50 1.88 0.75 0.75 1.31 1.50
DN50x50x15 (38,1) (38,1) (47,8) (19,0) (19,0) (33,3) (0,68) 86222
2x2x3/4 1.63 1.63 1.94 0.88 0.88 1.38 1.67
DN50x50x20 (41,4) (41,4) (49,3) (22,4) (22,4) (35,0) (0,76) 86223
2x2x1 1.75 1.75 2.00 1.00 1.00 1.31 1.91
DN50x50x25 (44,5) (44,5) (50,8) (25,4) (25,4) (33,3) (0,86) 86224
2x2x1-1/4 1.88 1.88 2.13 1.13 1.13 1.44 2.05
DN50 x 50 x 32 (47,8) (47,8) (54,1) (28,7) (28,7) (36,6) (0,93) 86225
2x2x1-1/2 2.00 2.00 2.19 1.25 1.25 1.50 2.11
DN50x50x40 (50,8) (50,8) (55,6) (31,8) (31,8) (38,1) (0,96) 86226
2x2x2-1/2 2.63 2.63 2.38 1.75 1.88 1.44 3.67
DN50x50x65 (66.8) (66,8) (47,8) (36,6) (1,66) 86227
2-1/2x2x3/4 1.75 1.63
(60,5)~44,5)
2.310.63 0.88 1.75 2.22
DN65x50x20 (44,5) (41,4) (58,7)15,9) (22,4) (44,5) (1,01) 86274
TABLE 5(2 0F2)
NOMINAL DIMENSIONS FIGURE 815
Page 8 of 10 TFPI7IO
!!!1111 Ii.u.r
iiiiiii
FIGURE 820 FIGURE 830 FIGURE 719
CAP BRASS SEAT UNION PLUG
Nominal Pipe
Size Figure 820 Figure 830 Figure 719
ANSI A Approx. A B Approx. A Approx.
Inches Inches Weight Part Inches Inches Weight Part Inches Weight Part
DN (mm) Lbs. Number (mm) (mm) Lbs. Number (mm) Lbs. Number
(kg) (kg) (kg)
1/2 0.88 0.15 72776 1.88 0.81 0.47 86207 0.94 0.10 86292 DN15 (22,4) (0,06) (47,8) (20,6) (0,21) (23,9) (0,04)
3/4 1.00 0.22 72777 2.00 0.94 0.66 86275 1.13 0.18 86293 DN20 (25,4) (0,10) (50,8) (23,9) (0,30) (28,7) (0,08)
1
DN25
1.18
(30,0)
0.33
(0,15) 72824 2.19
(55,6)
0.81
(20,6)
1.08
(0,49) 86276 86294
1.25
(31,7)
0.28
(0,13)
1-1/4 1.31 0.54 72756 2.50 1.06 1.54 86277 1.38 0.50 86295 DN32 (33,3) (0,24) (63,5) (2619) (0,70) (35,1) (0,23)
1-1/2 1.38 0.68 72822 2.63 1.19 2.03 86278 1.44 0.70 86296 DN40 (35,1) (0,31) (66,8) (30,2) (0,92) (36,6) (0,32)
2 1.50 0.96 72823 3.13 1.63 3.15 86279 1.50 0.90 86297 DNSO (38,1) (0,43) (79,5) (41,4) (1,43) (38,1) (0,41)
2-1/2 1.75 1.80
72825 - - - - - - - DN65 (44,5) (0,82)
TABLE 6
NOMINAL DIMENSIONS FIGURES 820,830 & 719
(D
TFPI7IO Page 9 of 10
FIGURE 825 FIGURE 827 FIGURE 816
EXTENSION PIECE HEX BUSHING REDUCING COUPLING
Nominal Pipe Figure 825 Figure 827 Figure 816
Size Extension Piece Hex Bushing Reducing Coupling
A Approx. A Approx. A B Approx.
ANSI Inches Inches Weight Part Inches Weight Part Inches Inches Weight Part
DN (mm) Lbs. Number (mm) Lbs. Number (mm) (mm) Lbs. Number
(kg) (kg) (kg)
1/2x1/2 1.50 0.20 72751 - - - - - DN15 x 15 (38,1) (0,09)
- -
1/2x1/2 2.00 0.27 72980 - - - - - DN15 x 15 (50,8) (0,12)
- -
3/4 x 3/4 1.50 0.22 72981 - - - - - DN20 x 20 (38,1) (0110)
- -
3/4x3/4 2.00 0.31 73982 - - - - - DN20 x 20 (50,8) (0,14)
- -
3/4 x 1/2 1.75 0.69 0.38 86772 DN20 x 15 - - - - - (43,2) (17,5) (0,17)
1 x 1/2 1.06 0.22 72726 1.69 0.50 0.38 86228 DN25 x 1 - - - (26,9) (0,10) (42,9) (12,7) (0,17)
1 x3/4
DN25 x 20 - - -
1.06
(26,9)
0.18
(0,08) 72762 1.75
(43,2)
0.50
(12,7)
0.53
(0,24)
86229
1-1/4x1 1.19 0.31 72763 DN32 x 25 - - - (30,2) - - (0,14)
- -
1-1/2x1 1.25 0.53 72757 DN40 x 25 - - - (31,7) - - (0,24)
- -
1-1/2 x1-1/4 1.25 0.35 72764 - - - DN40x32 - - - (31,7) (0110)
-
2 x 1.38 0.75 72759 - - DNSO x 25 - - - (35,1) (0,34)
- -
2x1-1/4 1.38 0.69 72761 - - DN50x32 - - - (35,1) (0,31)
- -
2 x 1-1/2 1.38 0.62 72775 DN50x40 - - - (35,1) 1 - - (0,28)
- -
TABLE 7
NOMINAL DIMENSIONS FIGURE 825,827 & 816
tqccllproducts
Ffre & Building
Technical Services: Tel: (800) 381-9312! Fax: (800) 791-5500
www.tyco-fire.com
Grinnell Grooved Fire Protection Products
Figure 40-5
Strap
General
Description
Listing/Approval lntormation
The Figure 40-5 Strap is an economical alternative
to welded pipe outlets on steel pipe.
The Figure 40-5 Strap may be used with full
lengths of pipe and eliminates threading and
welding, decreasing waste and installation time.
The 40-5 Strap may be used in wet, dry pipe and
deluge systems.
WARNING
The Figure 40-5 Strap described herein must be
installed and maintained in compliance with this
document, as we/las with theapplicab/estandards
of the National Fire Protection Association, in
addition to the standards of any otherautho rities
having jurisdiction. Failure to do so may impair
the performance of this device.
The owner is responsible for maintaining their
fire protection system and devices in proper
operating condition. The installing contractor or
sprinklermanufacturershouldbe contacted with
any questions.
Technical
Data
Figure: 40-5
Outlet: Threaded
Approvals: UL, FM, ULC, and VdS;
See Fire Protection Submittal Sheet for exact
Listing / Approval information.
Housing: Ductile iron conforming to
ASTM A-536, Grade 65-45-12
Protective Coatings:
Clear rust inhibitive coating
Zinc electroplated conforming to
ASTM B-633, Type III Service 2 (optional)
U-Bolt: Carbon steel conforming to
ASTM A-307, Grade A, Zinc electroplated
Nuts: Carbon steel conforming to
ASTM A-307, Grade A, Zinc electroplated
Gasket: (specify when ordering)
Grade 'E" EPDM green color code.
(See Data Sheet 1FP1895 for aid in selecting
proper gasket)
Ordering
Procedure
When placing an order, indicate the full product
name. Please specifythe quantity, figure number,
type of gasket, Grade "E" EPDM, and size.
Grinnell Grooved Piping Products, valves,
accessories and other products are available
throughoutthe U.S., Canada, and internationally,
through a network of distribution centers. You
may write directly or call 215-362-0700 for the
distributor nearest you.
Care and
Maintenance
The owner is responsible for the inspection,
testing, and maintenance of their fire protection
system and devices in accordance with the
applicable standards of the National Fire Protection
Association (e.g., NFPA 25), in addition to the
standards of any authority having jurisdiction.
The installing contractor or product manufacturer
should be contacted relative to any questions.
Any impairment must be immediately corrected.
It is recommended that automatic sprinkler
systems be inspected, tested, and maintained by
a qualified Inspection Service.
Limited
Warranty
Products manufactured by Tyco Fire Products are
warranted solely to the original Buyer for ten (10)
years against defects in material and workmanship
when paid for and properly installed and maintained
under normal use and service. This warranty will
expire ten (10) years from date of shipment bylyco
Fire Products. No warranty is given for products or
components manufactured by companies not
affiliated byownershipwithlyco Fire Productsorfor
products and components which have been subject
to misuse, improper installation, corrosion, orwhich
have not been installed, maintained, modified or
repaired in accordance with applicable Standards of
the National Fire Protection Association (NFPA),
and/orthe standards of any other Authorities Having
Jurisdiction. MateaIs found bylyco Fire Products
to be defective shall be either repaired or replaced, at
Tyco Fire Products' sole option. Tyco Fire Products
neither assumes, nor authorizes any person to
assume for it, any other obligation in connection with
the sale of products or parts of products. Tyco Fire
Products shall not be responsibleforspnnklersystem
design errorsorinaccurate orincomplete information
supplied by Buyer or Buyer's representatives.
IN NO EVENT SHALL TYCO FIRE PRODUCTS BE
LIABLE, IN CONTRACT, TORT, STRICT LIABILITY
OR UNDER ANY OTHER LEGAL THEORY, FOR
INCIDENTAL, INDIRECT, SPECIAL OR
CONSEQUENTIALDAMAGES, INCLUDING BUTNOT
LIMITED TO LABOR CHARGES, REGARDLESS OF
WHETHERTYCO FIRE PRODUCTSWAS INFORMED
ABOUT THE POSSIBILITY OF SUCH DAMAGES,
AND IN NO EVENT SHALL TYCO FIRE PRODUCTS'
LIABILITY EXCEED AN AMOUNT EQUAL TO THE
SALES PRICE.
THE FOREGOING WARRANTY IS MADE IN LIEU OF
ANY AND ALL OTHER WARR4WT1ES EXPRESS OR
IMPLIED, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE.
Page 1 of 2 September 2004 TFPI 720
Pipe Nominal Dimensions Hole Net
Size Size Wt. A B C D
Run x Inches Inches Inches Inches Inches Lbs.
Branch mm mm mm mm mm Kg.
11/4 X 1/20 2.00 1.50 3.50 1.20 13A6 0.84
50.8 38.1 88.9 30.5 30.2 0.4
11/4"X3/4° 2.00 1.50 3.50 1.20 13A6 0.88
50.8 38.1 88.9 30.5 30.2 0.4
11/4 i 2.31 1.68 3.50 1.20 1/16 1.13
58.7 42.7 88.9 30.5 30.2 0.5
11/20 x 1/20 2.12 1.62 3.50 1.32 1/i6 0.84
53.8 41.1 88.9 33.5 30.2 0.4
11/2 3/40 2.12 1.62 3.50 1.32 1/16 0.88
53.8 41.1 88.9 33.5 30.2 0.4
11/20 x i' 2.43 1.80 3.50 1.32 13A6 1.13
61.7 45.7 88.9 33.5 30.2 0.5
2°X 1/2 2.36 1.86 3.74 1.55 13A6 0.88
59.9 47.2 95.0 39.4 30.2 0.4
2°X3/4 2.36 1.86 3.74 1.55 1/16 0.95
59.9 47.2 95.0 39.4 30.2 0.4
2 x i 2.67 2.04 3.74 1.55 13A6 1.16
67.8 51.8 95.0 39.4 30.2 0.5
2V2 X 1/2 2.61 2.11 4.25 1.80 13A6 0.90
66.3 53.6 108.0 45.7 30.2 0.4
21/2"x3/4° 2.61 2.11 4.25 1.80 13A6 0.99
66.3 53.6 108.0 45.7 30.2 0.4
21/2 2.92 2.29 4.25 1.80 1/16 1.21
74.2 58.2 108.0 45.7 30.2 0.5
Item Description
1 Housing
2 Gasket
3 Flanged Nut
4 U-Bolt
Fitting
Size
Equivalent Length
(1 inch pipe)
11/40 x 1 8
11/20 x 1" 6
2'x 1" 6
21/2 x 1 4
The friction loss for these outlets is specified in
equivalent length of 1 inch Schedule 40 (C=120) pipe.
Page 2 of 2 TFP1 720
Figure 40-5 Strap
The 1 inch outlets can be used with a nipple leading Note: Outlet threads conforming to ISO 7-1 are available, contact
directly to a sprinkler. These fittings should be used Tyco Fire Products.
for hydraulically calculated systems only.
(:12
General Notes: It is the Designer's responsibility to select products suitable for the intended service and to ensure ISO that pressure ratings and performance data is not exceeded. Always read and understand the installation 9001
instructions (I1-1-1000). Never remove any piping component or corrector modify any piping deficiencies without
first depressurizing and draining the system. Material and gasket selection should be verified to be compatible
for the specific application. Certified Company
TYCO FIRE PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19946 Printed U.S.A.
tqCU /Fire & Building
I Products
Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500
Series TY-FRB - 23,42,5.6, and 8.0 K-factor
Upright, Pendent, and Recessed Pendent Sprinklers
Quick Response, Standard Coverage
General
Description
The Tyco® Series TY-FRB, 2.8, 4.2,
5.6, and 8.0 K-factor, Upright and Pen-
dent Sprinklers described in this data
sheet are quick response - standard
coverage, decorative 3 mm glass bulb
type spray sprinklers designed for use
in light or ordinary hazard, commercial
occupancies such as banks, hotels,
shopping malls, etc.
The recessed version of the Series
TY-FRB Pendent Sprinkler, where ap-
plicable, is intended for use in areas
with a finished ceiling. It uses either a
two-piece Style 10 (112 inch NPT) or
Style 40 (3/4 inch NPT) Recessed Es-
cutcheon with 1/2 inch (12,7 mm) of
recessed adjustment or up to 3/4 inch
(19,1 mm) of total adjustment from the
flush pendent position, or a two-piece
Style 20 (1/2 inch NPT) or Style 30 (3/4
inch NPT) Recessed Escutcheon with
1/4 inch (6,4 mm) of recessed adjust-
ment or up to 1/2 inch (12,7 mm) of
total adjustment from the flush pen-
dent position. The adjustment pro-
vided by the Recessed Escutcheon re-
duces the accuracy to which the fixed
pipe drops to the sprinklers must be
cut.
Corrosion resistant coatings, where
applicable, are utilized to extend the
life of copper alloy sprinklers beyond
that which would otherwise be ob-
IMPORTANT
Always refer to Technical Data
Sheet TFP 700 for the "INSTALLER
WARNING" that provides cautions
with respect to handling and instal-
lation of sprinkler systems and com-
ponents. Improper handling and in-
stallation can permanently damage
a sprinkler system or its compo-
nents and cause the sprinkler to fail
to operate in a fire situation or cause
it to operate prematurely.
Page 1 of 10
tamed when exposed to corrosive at-
mospheres. Although corrosion resis-
tant coated sprinklers have passed the
standard corrosion tests of the appli-
cable approval agencies, the testing is
not representative of all possible cor-
rosive atmospheres. Consequently, it
is recommended that the end user be
consulted with respect to the suitability
of these coatings for any given corro-
sive environment. The effects of ambi-
ent temperature, concentration of
chemicals, and gas/chemical velocity,
should be considered, as a minimum,
along with the corrosive nature of the
chemical to which the sprinklers will be
exposed.
An intermediate level versions of the
Series TY-FRB Pendent Sprinklers
are detailed in Technical Data Sheet
TFP356, and Sprinkler Guards are de-
tailed in Technical Data Sheet TFP780
WARNINGS
The Series TY-FRB Sprinklers de-
scribed herein must be installed and
maintained in compliance with this
document, as well as with the applica-
ble standards of the National Fire Pro-
tection Association, in addition to the
standards of any other authorities hav-
ing jurisdiction. Failure to do so may
impair the performance of these de-
vices.
The owner is responsible for maintain-
ing their fire protection system and de-
vices in proper , operating condition.
The installing contractor or sprinkler
manufacturer should be contacted
with any questions.
AUGUST, 2007
Model/Sprinkler
Identification
Numbers
TYII3I - Upright 2.8K, 1/2"NPT
TY1231 - Pendent 2.8K, 1/2"NPT
TY2131 - Upright 4.2K, 1/2"NPT
TY2231 - Pendent 4.2K, 1/2"NPT
TY3131 - Upright 5.6K, 1/2"NPT
Y31 - 'enaen 1I PII'l I TY4131 - Upright 8.0K, 3/4 NPT
TY4231 - Pendent 8.0K, 3/4"NPT
1Y4831- Upright 8.0K, 1/2"NPT
TY4931- Pendent 8.0K, 1/2"NPT
(B TFPI7I
I_ 2-7/8' (73,0 mm) DIA.
TFPI7I Page 3 of 10
ESCUTCHEON 7/16(11,1 mm) STYLE 10 or 20
PLATE SEATING 1/2 NOMINAL RECESSED
SURFACE MAKE-IN ESCUTCHEON NPT
2-3/16"
i5,6 mm)
(38,1 mm)
SSP DEFLECTOR *
SSU *
DEFLECTOR
7/16"
(11,1 mm)
YNOMINAL
MAKE-IN
2-3/16"
(55,6 mm)
1/2" NPT
6*
5
4
2
3
PENDENT RECESSED PENDENT I UPRIGHT CROSS SECTION
1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to 2 - Button Assembly 5 - Compression orifice seat on frame. Screw
FIGURE 3
QUICK RESPONSE SERIES TY-FRB UPRIGHT (TY3131) AND PENDENT (TY3231) SPRINKLERS
5.6 K-FACTOR, 1/2 INCH NPT
ESCUTCHEON 1/2" (12,7 mm)
PLATE SEATING NOMINAL
SURFACE MAKE-IN NPT
2-5/16"
(58,7 mm)
f
1-9/16'
I (39,7 mm)
I ,
SSP DEFLECTOR * 2-7/8"
PENDENT RECE.&
STYLE 30 or 40
RECESSED
ESCUTCHEON SSU
/ DEFLECTOR
6* I
1/2' 5
(1 mm)
OMINAL
WRENC (57,2 mm)
m)DIA. 3/ NPT
PENDENT UPRIGHT CROSS SECTION
1 - Frame 3 - Sealing b 6 - Deflector * Temperature rating is indicated on deflector or adjacent to 2- Button 5 - Compression orifice seat on frame. Screw
-
FIGURE 4
QUICK RESPONSE SERIES TY FRB UPRIGHT (TY4131) AND PENDENT (TY4231) SPRINKLERS
8.0 K-FACTOR, 314 INCH NPT
Page 4of1O TFPI7I
7/16° (11,1 mm)
NOMINAL SSU 1/2 MAKE-IN DEFLECTOR NPT
I *
F .
—
I 5
2-1/4' 2-3/16"
(57,2 mm) (55,6 4
1-9/16' WRENCH 2
(39,7 mm) FLATS 3
SP* 1
EFLECTOR CROSS
PE NT UPRIGHT SECTION
1 - Frame 3 - Sealing 4 ulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to
2 - Button Assembly - Compression orifice seat on frame. Screw
FIGURE 5
UICK RESPONSE SERIES TY-FRB UPRIGHT (TY4831) AND PENDENT (TY4931) SPRINKLERS
8.0 K-FACTOR, 1/2 INCH NPT
Technical
Data
Approvals
UL and C-UL Listed.
FM, LPCB, and NYC Approved.
(Refer to Table A and B for complete
approval information including corro-
sion resistant status.)
Maximum Working Pressure
Refer to Table C.
Discharge Coefficient
K = 2.8 GPM/psi112 (40,3 LPM/bari'2)
K = 4.2 GPM/psi112 (60,5 LPM/bar1'2)
K = 5.6 GPM/psill2 (80,6 LPM/barl'2)
K = 8.0 GPM/psi112 (115,2 LPM/bar1'2)
Temperature Ratings
Refer to Table A and B
Finishes
Sprinkler: Refer to Table A and B.
Recessed Escutcheon: White Coated,
Chrome Plated, or Brass Plated.
Physical Characteristics
Frame .............Bronze
Button .........Brass/Copper
Sealing Assembly ...........
Beryllium Nickel w/Teflont
Bulb ...............Glass
Compression Screw .....Bronze
Deflector .......Copper/Bronze
Bushing (K=2.8) .......Bronze
Operation
The glass Bulb contains a fluid which
expands when exposed to heat. When
the rated temperature is reached, the
fluid expands sufficiently to shatter the
glass Bulb, allowing the sprinkler to
activate and water to flow.
Design
Criteria
The Series TY-FRB Pendent and Up-
right Sprinklers are intended for fire
protection systems designed in ac-
cordance with the standard installation
rules recognized by the applicable
Listing or Approval agency (e.g., UL
Listing is based on the requirements of
NFPA 13, and FM Approval is based
on the requirements of FM's Loss Pre-
vention Data Sheets ). Only the Style
10, 20, 30, or 40 Recessed Escutch-
eon, as applicable, is to be used for
recessed pendent installations.
8
Page 6 of 10 TFPI7I
SPRINKLER FINISH (See Note 8)
K TYPE TEMP. BULB NATURAL Ii CHROME II WHITE* LEAD
LIQUID BRASS PLATED IPOLYESTER COATED
135F/57°C Orange
PENDENT
(1Y3231)
and
1,2,3,4,56,7 1,2,3,5
155°F/68°C Red
175°F/79°C Yellow
UPRIGHT 200F/93°C Green
5.6 (TY3131)
286°F/141°C Blue
1/2"
NPT 135°F/57°C Orange
PENDENT
(TY3231)* 1,2,4,5 N/A
RECESS EC 155°F/68°C Red
175°F/79°C Yellow
Figure 10 200°F/93°C Green
135F/57 °C Orange
RECESSED
PENDENT
(TY3231)** 1, 2, 3,4, 5 N/A
.155°F/68C Red
175F/79°C Yellow
Figure 11 200°F/93°C Green
135F/57°C Orange
PENDENT
(TY4231)
and 1,2, 3,4, 5, 6, 7
1,2,5
155°F/68C Red
175°F/79°C Yellow
200°F/93°C Green UPRIGHT
8.0 (TY4131)
286F/141°C Blue 3/4',
NPT 135°F/57°C Green
RECESSED
PENDENT
(TY4231)* 1, 2,4, 5 N/A
155°F/68°C Orange
175°F/79°C Red
Figure 12 200°F/93°C Yellow
135°F/57°C Orange
RECESSED
PENDENT
(1Y4231)** 1,2, 3,4, 5 N/A
155°F/68C Red
175°F/79°C Yellow
Figure 13 200°F/93°C Green
135°F/57°C Orange
8.0
1/2"
PENDENT
(TY4931)
and 1, 2,4, 5, 6
1,2,5
155°F/68°C Red
175°F/79°C Yellow
200°F/93°C Green NPT UPRIGHT
(TY4831)
286F/141°C Blue
NOTES:
Listed by Underwriters Laboratories, Inc. (UL) as Quick Response Sprinklers.
Listed by Underwriters Laboratories, Inc. for use in Canada (C-UL) as Quick Response Sprinklers.
Approved by Factory Mutual Research Corporation (FM) as Quick Response Sprinklers.
Approved by the Loss Prevention Certification Board (LPCB Ref. No. 007k104) as Quick Response Sprinklers; however, the
LPCB does not rate the thermal sensitivity of recessed sprinklers.
Approved by the City of New York under MEA 354-01-E.
VdS Approved (For details contact Tyco Fire & Building Products, Enschede, Netherlands, Tel. 31-53-428-4444/Fax 31-53-428-3377).
Approved by the Loss Prevention Certification Board (LPCB Ref. No. 094a/06) as Quick Response Sprinklers.
Where Polyester Coated and Lead Coated Sprinklers are noted to be UL and C-UL Listed, the sprinklers are UL and C-UL Listed as
Corrosion Resistant Sprinklers. Where Lead Coated Sprinklers are noted to be FM Approved, the sprinklers are FM Approved as a
Corrosion Resistant Sprinklers.
* Installed with Style 10 (1/2" NPT) or Style 40 (3/4" NPT) 3/4" Total Adjustment Recessed Escutcheon, as applicable.
** Installed with Style 20 (1/2" NPT) or Style 30 (3/4" NPT) 1/2" Total Adjustment Recessed Escutcheon, as applicable.
Frame and Deflector only. Listings and approvals apply to color (Special Order).
N/A: Not Available
TABLE B
LABORATORY LISTINGS AND APPROVALS
5.6 AND 8.0 K-FACTOR SPRINKLERS
TFPI7I Page 7 of 10
SPRINKLER FINISH
K TYPE NATURAL CHROME WHITE LEAD
BRASS I PLATED POLYESTER COATED
PENDENT (TY3231)
and
2.8 UPRIGHT (TY3131) 175 PSI (12,1 BAR) N/A
1/2' RECESSED PENDENT NPT (1Y323)
PENDENT (TY4231)
and
4.2 UPRIGHT (TY4131) 175 PSI (12,1 BAR) N/A
3/4" RECESSED PENDENT NPT (TY4231)
PENDENT (TY3231)
and 250 PSI (17,2 BAR) 175 PSI (12,1 BAR)
5.6 UPRIGHT (TY3131) OR
1/2" 175 PSI (12,1 BAR) RECESSED PENDENT NPT (1Y3231) (SEE NOTE 1) N/A
- PENDENT (1Y4231)
and 175 PSI (12,1 BAR) 175 PSI (112,11 BAR)
8.0 UPRIGHT (TY4131)
RECESSED PENDENT NPT (1Y4231) N/A
80 PENDENT (TY4931)
1/2" and 175 PSI (12,1 BAR) 175 PSI (12,1 BAR)
NPT UPRIGHT (TY4831)
NOTES:
1. The maximum working pressure of 250 psi (17,2 bar) only applies to the Listing by Underwriters Laboratories Inc. (UL); the Listing by
Underwriters Laboratories, Inc. for use in Canada (C-UL); and , the Approval by the City of New York.
TABLE C, MAXIMUM WORKING PRESSURE
Installation
The Series TY-FRB Sprinklers must
be installed in accordance with the fol-
lowing instructions:
NOTES
Do not install any bulb type sprinkler if
the bulb is cracked or there is a loss of
liquid from the bulb. With the sprinkler
held horizontally, a small air bubble
should be present. The diameter of the
air bubble is approximately 1/16 inch
(1,6 mm) for the 135°F/57C to 3/32
inch (2,4 mm) for the 286°F/141'C
temperature ratings.
A leak tight 1/2 inch NPT sprinkler joint
should be obtained with a torque of 7
to 14 ft.lbs. (9,5 to 19,0 Nm). A maxi-
mum of 21 ft. lbs. (28,5 Nm) of torque
may be used to install sprinklers with
1/2 NPT connections. A leak tight 3/4
inch NPT sprinkler joint should be ob-
tained with a torque of 10 to 20 ft.lbs.
(13,4 to 26,8 Nm). A maximum of 30
ft.lbs. (40,7 Nm) of torque is to be used
to install sprinklers with 3/4 NPT con-
nections. Higher levels of torque may
distort the sprinkler inlet and cause
leakage or impairment of the sprinkler.
Do not attempt to make-up for insuffi-
cient adjustment in the escutcheon
plate by under- or over-tightening the
sprinkler. Readjust the position of the
sprinkler fitting to suit.
The Series TY-FRB Pendent and Up-
right Sprinklers must be installed in
accordance with the following instruc-
tions.
Step 1. Pendent sprinklers are to be
installed in the pendent position, and
upright sprinklers are to be installed in
the upright position.
Step 2. With pipe thread sealant ap-
plied to the pipe threads, hand tighten
the sprinkler into the sprinkler fitting.
Step 3. Tighten the sprinkler into the
sprinkler fitting using only the W-Type
6 Sprinkler Wrench (Ref. Figure 14).
With reference to Figures 1, 2, 3, 4,
and 5, the W-Type 6 Sprinkler Wrench
is to be applied to the sprinkler wrench
flats.
The Series TY-FRB Recessed Pen-
dent Sprinklers must be installed in
accordance with the following instruc-
tions.
Step A. After installing the Style 10.
20, 30, or 40 Mounting Plate, as appli-
cable, over the sprinkler threads and
with pipe thread sealant applied to the
pipe threads, hand tighten the sprin-
kler into the sprinkler fitting.
Step B. Tighten the sprinkler into the
sprinkler fitting using only the W-Type
7 Recessed Sprinkler Wrench (Ref.
Figure 15). With reference to Figure 1,
2, 3, and 4, the W-Type 7 Recessed
TFPI7I
- 2-7/8 DIA.
5/811/4" (73,0 mm) 3/4" (19,1 mm
(15,9±6,4 mm) 2-1/4" DIA. 1/4' (6,4
FACE OF (57,2 mm) MO TING SPRINKLER PLATE FITTING
I l/B"
(3,2 mm)
1$ MOUNTING
SURFACE
SERIES 1-1/4(31,8 mm)1 CLOSURE TY-FRB 3/4" (19,1 mm)
FIGURE 10
RIES TY-FRB RECESSED PENDENT
WIT TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT
STYLE 10 RECESSED ESCUTCHEON
5.6 K-FACTOR, 1/2 INCH NPT
2-7/8" DIA.
5/8±1/4" (73,0 mm) 3/4(19,1 mm)
(15,9±6,4 mm) - 2-1/4" DIA. 1/4" (6,4 m
(57,2 mm) FACE OF MO ING
SPRINKLER LATE
FITTING
/ 1/8"
I - (3,2 mm)
if
MOUNTING
SURFACE
CLOSURE SERIES 1-5/16" (33,3 mm)
TY-FRB 13/16" (20,6 mm)
FIGURE 12
S IES TY-FRB RECESSED PENDENT
WIT 0-PIECE 3/4 INCH TOTAL ADJUSTMENT
STYLE 40 RECESSED ESCUTCHEON
8.0 K-FACTOR, 3/4 INCH NPT
Page 9 of 10
- 2-7/8" DIA. • I
(73,0 mm) 1/2±1/8" 1/2"(12,7m
E (12,713,2 mm) - 2-1/4" DIA. I 1/4" (6,4 m)
FACE OF M SPRINKLER PLATE
mm) TING
FITTING
I (32mm)
\ MOUNTING
SURFACE/
SERIES
SERIES 1-1/4" (31,8 mm) CLOSURE TYFRB 1" (25,4 mm)
FIGURE 11
RIES TY-FRB RECESSED PENDENT
WI TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT
STYLE 20 RECESSED ESCUTCHEON
5.6 K-FACTOR, 1/2 INCH NPT
- 2-7/8" DIA.
1/2±1/8" (73,0 mm) 1/2" (12,7 mm)
(12,7±3,2 mm) 2-1/4" DIA. 1/4" (6,4
(57,2 mm) FACE OF MO TING
SPRINKLER LATE
FITTING
/ 1/8"
I - (3,2 mm)
1117A 1
MOUNTING
SURFACE
CLOSURE SERIES 1-5/16" (33,3 mm)
1YFRB 1-1/16" (27,0 mm)
FIGURE 13
RIES TY-FRB RECESSED PENDENT
WIT TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT
STYLE 30 RECESSED ESCUTCHEON
8.0 K-FACTOR, 3/4 INCH NPT
pleted, to verify the integrity of the cor-
rosion resistant coating. Thereafter,
annual inspections per NFPA 25
should suffice; however, instead of in-
specting from the floor level, a random
sampling of close-up visual inspec-
tions should be made, so as to better
determine the exact sprinkler condi-
tion and the long term integrity of the
corrosion resistant coating, as it may
be affected by the corrosive conditions
present.
The owner is responsible for the in-
spection, testing, and maintenance of
their fire protection system and de-
vices in compliance with this docu-
ment, as well as with the applicable
standards of the National Fire Protec-
tion Association (e.g., NFPA 25), in
addition to the standards of any other
authorities having jurisdiction. The in-
stalling contractor or sprinkler manu-
WRENCH RECESS
(END "A" USED FOR
1/2" NPT MODELS)
WRENCH RECESS
(END "B" USED FOR
3/4" NPT MODELS)
FIGURE 14
W-TYPE 6 SPRINKLER
WRENCH
facturer should be contacted relative
to any questions.
It is recommended that automatic
sprinkler systems be inspected,
tested, and maintained by a qualified
WRENCH
RECESS
PUSH WRENCH
INTO ENSURE
ENGAGEMENT
WITH SPRINKLER
WRENCHING AREA
FIGURE 15
W-TYPE 7 RECESSED
SPRINKLER WRENCH
Inspection Service in accordance with
local requirements and/or national
codes.
8
Page lOoflO TFPI7I
P/N 57 - XXX - X - XXX
I MODEL/SIN I I
I
4
3
7
1Y4131
SPRINKLER
NATURAL BRASS
WHITE POLYESTER
WHITE (RAL9010)*
CHROME PLATED
LEAD COATED
I RATING
135 135F/57°C
155 155°F/68°C
175 175°F/79°C
200 200°F/93°C
286 286°F/141°C
* Eastern Hemisphere sales only.
330 2.8K UPRIGHT (1/2"NPT) TY113I
331 2.8K PENDENT (1/2"NPT) TY1231
340 4.2K UPRIGHT (1/2"NPT) TY2131
341 4.2K PENDENT (1/2"NPT) TY2231
370 5.6K UPRIGHT (1/2"NPT) 1Y3131
371 5.6K PENDENT (1/2"NPT) TY3231
390 8.0K UPRIGHT (3/4"NPT)
391 8.0K PENDENT (3/4"NPT) 1Y4231
360 8.0K UPRIGHT (1/2"NPT) TY4831*
361 8.0K PENDENT (1/2"NPT) TY4931*
TABLED
PART NUMBER SELECTION
SERIES TY-FRB PENDENT AND UPRIGHT SPRINKLERS
Limited
Warranty
Products manufactured by Tyco Fire &
Building Products (TFBP) are war-
ranted solely to the original Buyer for
ten (10) years against defects in mate-
rial and workmanship when paid for
and properly installed and maintained
under normal use and service. This
warranty will expire ten (10) years
from date of shipment by TFBP. No
warranty is given for products or com-
ponents manufactured by companies
not affiliated by ownership with TFBP
or for products and components which
have been subject to misuse, improper
installation, corrosion, or which have
not been installed, maintained, modi-
fied or repaired in accordance with ap-
plicable Standards of the National Fire
Protection Association, and/or the
standards of any other Authorities
Having Jurisdiction. Materials found
by TFBP to be defective shall be either
repaired or replaced, at TFBP's sole
option. TFBP neither assumes, nor
authorizes any person to assume for it,
any other obligation in connection with
the sale of products or parts of prod-
ucts. TFBP shall not be responsible for
sprinkler system design errors or inac-
curate or incomplete information sup-
plied by Buyer or Buyer's repre-
sentatives.
In no event shall TFBP be liable, in
contract, tort, strict liability or under
any other legal theory, for incidental,
indirect, special or consequential dam-
ages, including but not limited to labor
charges, regardless of whether TFBP
was informed about the possibility of
such damages, and in no event shall
TFBP's liability exceed an amount
equal to the sales price.
of merchantability and fitness for a oar-
This limited warranty sets forth the ex-
clusive remedy for claims based on
failure of or defect in products, materi-
als or components, whether the claim
is made in contract, tort, strict liability
or any other legal theory.
This warranty will apply to the full ex-
tent permitted by law. The invalidity, in
whole or part, of any portion of this
warranty will not affect the remainder.
Ordering
Procedure
When placing an order, indicate the
full product name. Refer to the Price
List for complete listing of Part Num-
bers.
Contact your local distributor for avail-
ability.
Sprinkler Assemblies with NPT
Thread Connections:
Specify: (Specify Model/SIN), Quick
Response, (specify K-factor), (specify
temperature rating), Series TY-FRB
(specify Pendent or Upright) Sprinkler
with (specify type of finish or coating),
P/N (specify from Table D).
Recessed Escutcheon:
Specify: Style (10, 20, 30, or 40) Re-
cessed Escutcheon with (specify*) fin-
ish, P/N (specify*).
* Refer to Technical Data Sheet 1FP770.
Sprinkler Wrench:
Specify: W-Type 6 Sprinkler Wrench,
P/N 56-000-6-387.
Specify: W-Type 7 Sprinkler Wrench,
P/N 56-850-4-001.
TYCO FIRE & BUILDING PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446
tqCD /Fire & Building
I Products
Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500
Series RFII - 5.6 K-factor
"Royal Flush II" Pendent Concealed Sprinklers
Quick & Standard Response, Standard Coverage
General
Description
The Series RFII Quick Response
(3 mm bulb) & Standard Response (5
mm bulb), 5.6 K-Factor, "Royal Flush
II" Concealed Pendent Sprinklers are
decorative sprinklers featuring a flat
cover plate designed to conceal the
sprinkler. It is the best choice for archi-
tecturally sensitive areas such as hotel
lobbies, office buildings, churches,
and restaurants.
Each unit includes a Cover Plate As-
sembly that conceals the sprinkler op-
erating components above the ceiling.
The separable two-piece design of the
Cover Plate and Support Cup Assem-
blies allows installation of the sprin-
klers and pressure testing of the fire
protection system prior to installation
of a suspended ceiling or application
of the finish coating to a fixed ceiling.
They also permit removal of sus-
pended ceiling panels for access to
building service equipment without
having to first shut down the fire pro-
tection system and remove sprinklers.
Also, the separable two-piece design
of the the Sprinkler provides for 1/2
inch (12,7 mm) of vertical adjustment,
to reduce the accuracy to which the
length of fixed pipe drops to the sprin-
klers must be cut.
The Series RFII Sprinklers are
shipped with a Disposable Protective
IMPORTANT
Always refer to Technical Data
Sheet TFP 700 for the "INSTALLER
WARNING' that provides cautions
with respect to handling and Instal-
lation of sprinkler systems and com-
ponents. Improper handling and in-
stallation can permanently damage
a sprinkler system or its compo-
nents and cause the sprinkler to fall
to operate in a fire situation or cause
if to operate prematurely.
Cap. The Protective Cap is temporarily
removed for installation, and then it
can be replaced to help protect the
sprinkler while the ceiling is being in-
stalled or finished. The tip of the Pro-
tective Cap can also be used to mark
the center of the ceiling hole into plas-
ter board, ceiling tiles, etc. by gently
pushing the ceiling product against the
Protective Cap. When the ceiling in-
stallation is complete the Protective
Cap is removed and the Cover Plate
Assembly installed.
As an option, the Series RFII Standard
Response (5 mm bulb) "Royal Flush II"
Concealed Pendent Sprinklers may be
fitted with a silicone Air and Dust Seal
(Ref. Fig. 5). The Air and Dust Seal is
intended for sensitive areas where it is
desirable to stop air and dust travel
through the cover plate from the area
above the ceiling.
WARNINGS
The Series RFll Concealed Pendent
Sprinklers described herein must be
installed and maintained in compli-
ance with this document, as well as
with the applicable standards of the
National Fire Protection Association,
in addition to the standards of any
other authorities having jurisdiction.
Failure to do so may impair the per-
formance of these devices.
The owner is responsible for maintain-
ing their fire protection system and de-
vices in proper operating condition.
The installing contractor or sprinkler
manufacturer should be contacted
with any questions.
Model/Sprinkler
Identification
Numbers
TY3551 (5 mm bulb)
ITY3531 (3 mm bulb)I
Technical
Data
Approvals for Series RFII
UL and C-UL Listed. FM Approved.
NYC under MEA 353-01-E. LPCB
(Ref. No. 094a/09 for 1Y3551 &
094a/10 for.TY3531)Approved.
The approvals apply only to the serv-
ice conditions indicated in the Design
Criteria section.
Approvals for Air & Dust Seal
(Part #10908100)
UL and C-UL Listed for use with the
RFII (TY3551) Standard Response
Concealed Sprinkler.
Maximum Working Pressure;
Maximum 250 psi (17,3 bar) by UL,
C-UL, and NYC. Maximum 175 psi
(12,1 bar) by FM and LPCB.
Temperature Ratings
155F/68C Sprinkler - 135F/57C Plate
200F/93C Sprinkler - 165F/74C Plate
Discharge Coefficient
K = 5.6 GPM/psi1'2 (80,6 LPM/barl/2)
Adjustment
1/2 inch (12,7 mm)
Finishes
Cover Plate: Chrome Plated, Brass
Plated, or White Painted (Custom
paint matches and colors other than
white are available on request.) 2 0
TFPI8I Page 1 of 4 JANUARY, 2008
Page 2 of 4 TFPI8I
1/2 NPT SEALING
ASSEMBLY
FRAME
CAP
SUPPORT
CUP WITH BULB
ROLL FORMED
THREADS
COMPRESSION
SCREW
GUIDE -
PINS (2)
DEFLECTOR
(DROPPED
DEFLECTOR I POSITION)
SPRINKLER/SUPPORT CUP
ASSEMBLY
THREAD INTO [ TAINER
SUPPORT CUP THREAD
UNTIL MOUNTING 0 0 MPLES
SURFACE IS
FLUSH WITH LEJECTION
CEILING RING
SOLDER
IL
COVER
TABS (3) COVER PLATE/RETAINER PLATE ASSEMBLY
FIGURE 1
SERIES RFII CONCEALED SPRINKLER
ASSEMBLY
Physical Characteristics
Frame .............Bronze
Support Cup . Chrome Plated Steel
Guide Pins ......Stainless Steel
Deflector ............Bronze
Compression Screw ......Brass
Bulb ...............Glass
Cap ........Bronze or Copper
Sealing Assembly ..........
Beryllium Nickel w/Teflon*
Cover Plate ...........Brass
Retainer ............Brass
Ejection Spring . . . . Stainless Steel
Patents
U.S.A. 4,014,388
Operation
When exposed to heat from a fire, the
Cover Plate, which is normally sol-
dered to the Retainer at three points,
falls away to expose the Sprinkler As-
sembly. At this point the Deflector sup-
ported by the Guide Pins drops down
to its operational position.
The glass Bulb contains a fluid that
expands when exposed to heat. When
the rated temperature is reached, the
fluid expands sufficiently to shatter the
glass Bulb, activating the sprinkler and
allowing water to flow.
Design
Criteria
The RFII (TY3551), 5 mm Bulb Type,
Concealed Pendent Sprinklers are UL
and C-UL Listed as standard response
- standard spray sprinklers for use in
accordance with the current NFPA
standard. They are FM Approved as
standard response - standard spray
sprinklers for use in accordance with
the current FM Loss Prevention Data
Sheets.
The RFII (1Y3531) 3 mm Bulb Type,
Concealed Pendent Sprinklers are UL
and C-UL Listed as quick response -
standard spray sprinklers for use in
accordance with the current NFPA
standard. They are FM Approved as
standard response - standard spray
sprinklers for use in accordance with
the current FM Loss Prevention Data
Sheets.
The Series RFII Concealed Pendent
Sprinklers are only listed and ap-
proved with the Series RFII Concealed
Cover Plates having a metallic or white
painted finish.
The Series RFII must not be used in
applications where the air pressure
above the ceiling is greater than that
below. Down drafts through the Sup-
port Cup could delay sprinkler opera-
tion in a fire situation.
Installation
The Series RFII must be installed in
accordance with the following instruc-
tions:
NOTES
Do not install any bulb type sprinkler if
the bulb is cracked or there is a loss of
liquid from the bulb. With the sprinkler
held horizontally, a small air bubble
should be present. The diameter of the
air bubble is approximately 1/16 inch
(1,6 mm) for the 155°F/68°C and 3/32
inch (2,4 mm) for the 200°F/93°C tem-
perature ratings.
A 1/2 inch NPT sprinkler joint should
be obtained with a minimum to maxi-
mum torque of 7 to 14 ft.lbs. (9,5 to
19,0 Nm). Higher levels of torque may
distort the sprinkler inlet with conse-
quent leakage or impairment of the
sprinkler.
Do not attempt to compensate for in-
sufficient adjustment in the Sprinkler
Assembly by under- or over-tightening
the Sprinkler/Support Cup Assembly.
Readjust the position of the sprinkler
fitting to suit.
Step 1. The sprinkler must only be
installed in the pendent position and
with the centerline of the sprinkler per-
pendicular to the mounting surface.
Step 2. Remove the Protective Cap.
Step 3. With pipe thread Sealant ap-
plied to the pipe threads, hand tighten
the sprinkler into the sprinkler fitting.
Step 4. Wrench tighten the sprinkler
using only the RFII Sprinkler Wrench
(Ref. Figure 3). The RFll Sprinkler
Wrench is to be applied to the Sprin-
kler as shown in Figure 3.
Step 5. Replace the Protective Cap
(Ref. Figure 4) by pushing it upwards
until it bottoms out against the Support
Cup. The Protective Cap helps prevent
damage to the Deflector and Arms dur-
ing ceiling installation and/or during
application of the finish coating of the
ceiling. It may also be used to locate
the center of the clearance hole by
gently pushing the ceiling material up
against the center point of the Protec-
tive Cap.
NOTE
As long as the Protective Cap remains
in place, the system is considered to
be "Out of Service". -i
* Registered Trademark of DuPont
CLEARANCE HOLE
FIGURE 4
DISPOSABLE PROTECTIVE CAP
Step 6. After the ceiling has been com-
pleted with the 2-1/2 inch (63,5 mm)
diameter clearance hole and in prepa-
ration for installing the Cover Plate As-
sembly, remove and discard the Pro-
tective Cap, and verify that the
Deflector moves up and down freely. If
the Sprinkler has been damaged and
the Deflector does not move up and
down freely, replace the entire Sprin-
kler assembly. Do not attempt to mod-
ify or repair a damaged sprinkler.
Step 7. When installing an Air and
Dust Seal, refer to Figure 5, otherwise
proceed to Step 8. To attach the Air
and Dust Seal, verify the angle of the
outside edge of the seal is oriented
according to Figure 5. Start the edge
of the Retainer in the grooved slot of
the Air and Dust Seal and continue
around the retainer until the entire Air
and Dust Seal is engaged.
NOTE
The Air and Dust Seal is only to be
installed on the periphery of the Re-
tainer.
Step 8. Screw on the Cover Plate/Re-
tainer Assembly until the Retainer -
Figure 2 (or Air and Dust Seal - Figure
5) contacts with the ceiling. Do not
continue to screw on the Cover
Plate/Retainer Assembly such that it
lifts a ceiling panel out of its normal
position. If the Cover Plate/Retainer
Assembly cannot be engaged with the
Support Cup or the Cover Plate/Re-
tainer Assembly cannot be engaged
sufficiently to contact the ceiling, the
Sprinkler Fitting must be repositioned.
Care and
Maintenance
The Series RFII must be maintained
and serviced in accordance with the
following instructions:
NOTES
Absence of the Cover Plate Assembly
may delay sprinkler operation in a fire
situation.
22 ( D
TFPI8I Page 3 of 4
FACE OF CLEARANCE HOLE
SPRINKLER DIAMETER
FITTING DIMENSION C
SPRINKLER
SUPPORT CUP
ASSEMBLY
1/2(12,7mm)
THREADED
D ADJUSTMENT
FACE OF CEILING,
RETAINING RING
MOUNTING M4 SURFACE
I
,
F/7
I
II II II
V
3/16 to 11/16 MANUFACTURER DEFLECTOR COVER PLATE
(4,8 to 17,5 mm) PRESET GAP IN DROPPED RETAINER
REFERENCE 3/32" (2,4 mm) POSITION ASSEMBLY
COVER PLATE COVER PLATE
- PROFILE DEPTH DIAMETER
DIMENSION B DIMENSION A
3-1/4" (82,6 mm) C: 2-3/8" to 2-5/8° (60,3 to 66,7 mm)
3/16" (4,8 mm) D: 1-3/4° to 2-1/4" (44,5 to 57,2 mm)
FIGURE 2
SERIES RFII CONCEALED SPRINKLER
INS LA TION DIMENSIONS
FRAME
ARM
-
SUPPORT
CUP
_
T17/8" (23 mm)
SQUARE
ALIGN
ARROWS WITH
FRAME ARMS
ACCEPTS
1/2" SOCKET
DRIVE
FIGURE 3
RFII SPRINKLER WRENCH
Page 4 of 4 TFPI8I
SUPPORT SPRINKLER FACE OF ORIENT
CUP CEILING SEAL / BEVELAS
SHOWN COVER
PLAT
TER
_
ASSEMBLY
CLEAN
/ ROOM
LIP OF COVER SEAL
RETAINER PLATE
FIGURE 5
OPTIONAL AIR AND DUST SEAL FOR SERIES RFII (TY3551)
When properly installed, there is a
nominal 3/32 inch (2,4 mm) air gap
between the lip of the Cover Plate and
the ceiling, as shown in Figure 2. This
air gap is necessary for proper opera-
tion of the sprinkler. If the ceiling is to
be repainted after the installation of
the Sprinkler, care must be exercised
to ensure that the new paint does NOT
seal off any of the air gap.
Factory painted Cover Plates MUST
NOT be repainted. They should be re-
placed, if necessary, by factory
painted units.
Do not pull the Cover Plate relative to
the Enclosure. Separation may result.
Before closing a fire protection system
main control valve for maintenance
work on the fire protection system that
it controls, permission to shut down the
affected fire protection system must be
obtained from the proper authorities
and all personnel who may be affected
by this action must be notified.
Sprinklers that are found to be leaking
or exhibiting visible signs of corrosion
must be replaced.
Automatic sprinklers must never be
painted, plated, coated or otherwise
altered after leaving the factory. Modi-
fied sprinklers must be replaced.
Sprinklers that have been exposed to
corrosive products of combustion, but
have not operated, should be replaced
if they cannot be completely cleaned
by wiping the sprinkler with a cloth or
by brushing it with a soft bristle brush.
Care must be exercised to avoid dam-
age to the sprinklers - before, during,
and after installation. Sprinklers dam-
aged by dropping, striking, wrench
twist/slippage, or the like, must be re-
placed. Also, replace any sprinkler that
has a cracked bulb or that has lost
liquid from its bulb. (Ref. Installation
Section).
If a sprinkler must be removed, do not
reinstall it or a replacement without
reinstalling the Cover Plate Assembly.
If a Cover Plate Assembly becomes
dislodged during service, replace it im-
mediately.
The owner is responsible for the in-
spection, testing, and maintenance of
their fire protection system and de-
vices in compliance with this docu-
ment, as well as with the applicable
standards of the National Fire Protec-
tion Association (e.g., NFPA 25), in
addition to the standards of any other
authorities having jurisdiction. The in-
stalling contractor or sprinkler manu-
facturer should be contacted relative
to any questions.
Automatic sprinkler systems should be
inspected, tested, and maintained by a
qualified Inspection Service in accord-
ance with local requirements and/or
national codes.
Limited
Warranty
Products manufactured by Tyco Fire &
Building Products (TFBP) are war-
ranted solely to the original Buyer for
ten (10) years against defects in mate-
rial and workmanship when paid for
and properly installed and maintained
under normal use and service. This
warranty will expire ten (10) years
from date of shipment by TFBP. No
warranty is given for products or com-
ponents manufactured by companies
not affiliated by ownership with TFBP
or for products and components which
have been subject to misuse, improper
installation, corrosion, or which have
not been installed, maintained, modi-
fied or repaired in accordance with ap-
plicable Standards of the National Fire
Protection Association, and/or the
standards of any other Authorities
Having Jurisdiction. Materials found
by TFBP to be defective shall be either
repaired or replaced, at TFBP's sole
option. TFBP neither assumes, nor
authorizes any person to assume for it,
any other obligation in connection with
the sale of products or parts of prod-
ucts. TFBP shall not be responsible for
sprinkler system design errors or inac-
curate or incomplete information sup-
plied by Buyer or Buyer's repre-
sentatives.
In no event shall TFBP be liable, in
contract, tort, strict liability or under
any other legal theory, for incidental,
indirect, special or consequential dam-
ages, including but not limited to labor
charges, regardless of whether TFBP
was informed about the possibility of
such damages, and in no event shall
TFBP's liability exceed an amount
equal to the sales price.
The foregoing warranty is made in lieu
of any and all other warranties, ex-
press or implied, including warranties
of merchantability and fitness for a
particular purpose.
This limited warranty sets forth the ex-
clusive remedy for claims based on
failure of or defect in products, materi-
als or components, whether the claim
is made in contract, tort, strict liability
or any other legal theory.
This warranty will apply to the full ex-
tent permitted by law. The invalidity, in
whole or part, of any portion of this
warranty will not affect the remainder
Ordering
Procedure
When placing an order, indicate the
full product name. Contact your local
distributor for availability.
Sprinkler Assembly:
Specify: (SIN), (specify temperature
rating) Series RFII Concealed Pen-
dent Sprinkler, P/N (specify).
155F/68C 200F/93C
1Y3551 51-790-1-155 51-790-1-200
ITv3531 51-792-1-155 I 51-792-1-200
Separately Ordered Cover Plate:
Specify: (specify temperature rating)
Series RFII Concealed Cover Plate
with (specify finish), P/N (specify).
135F/57C(a) 165F/74C(b)
Brass 56-792-1-135 56-792-1-165
Bright Brass 56-792-2-135 56-792-2-165
Chrome 56-792-9-135 56-792-9-165
Brushed Chrome 56-792-8-135 56-792-8-165
White 56-792-0-135 56-792-0-165
White (RAL9O1 )* 56-792-3-135 56-792-3-165
lBriht White 56-792-4-135 I 56-792-4-165
Off White 56-792-5-135 56-792-5-165
Black 56-792-6-135 56-792-6-165
Custom 56-792-X-1 35 56-792-X-165
For use with 155F/68C sprinklers.
For use with 200F/93C sprinklers.
* Eastern Hemisphere sales only.
Sprinkler Wrench:
Specify: RFII Sprinkler Wrench,
P/N 56-000-1-075.
Air and Dust Seal:
Specify: Air and Dust Seal,
P/N 56-908-1-001.
(D
@2008 TYCO FIRE & BUILDING PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446
300
RING HANGER
1 thru 4 inch pipe 1/2 and 3/4 Inch pipe
5 thru 8 inch pipe
SIZE - 1/2 thru 8 inch pipe.
MATERIAL - Carbon Steel, Mil. Galvanized to G-90 specification.
FINISH - Mil. Galvanized and Stainless Steel.
LISTING - UL in US and CANADA.
APPROVAL - Factory Mutual Research.
CONFORMS WITH: Federal Specification WW-H- 171(Type 10),
Manufacturers Standardization Society ANSI/MSS-SP-58 (Type 10); install
in accordance with ANSI/MS S- SP-69.
MAXIMUM TEMPERATURE - 650°F.
FUNCTION - For fire sprinkler and general piping purposes.
Swivel nut permits hanger adjustment after installation.
FEATURES -
1 thru 4 inch:
* Offset edge for EASY pipe insertion.
1 thru 8 inch:
* Full length knurl on swivel nut for better grip.
UNIQUE FEATURES
1 thru 3 inch:
* UL listed to accept AFCON #310 Surge Restrainer.
* Swivel nut
Retained in ring to keep the assembly intact prior to installation.
Removed easily if needed.
* UL listed for use on CPVC pipe.
ORDERING - Part # and pipe size.
Index
02/01
IMPERIAL MAX REC.
LOAD LBS.
METRIC*
PIPE TROD PIPE ROD
1/2 3/8 400 10
3/4 3/8 400 20 10
400 25 10
1 114 3/8 400 32 10
11/2 1 3/8 400 40 10
2 400 50 10
21/2 600 65 10
3 3/8 600 80to
31/2 600 10
1000 100 10
5 1250 125 12
6 1250 150 12
8 1250
Order Part #300m
Note: 1/2" Ring Hanger not <FM> approved
8
!Acsn
655
ALL THREADED ROD CUT TO LENGTH
ROD
SIZE
MAX. REC. LOAD LBS.
FOR SERVICE TEMP.
650°F 750°F
3/8 610 540
1/2 1130 1010
5/8 1810 1610
3/4 2710 2420
7/8 3770 3360
NOTE; maximum Temperature: 750°F
SIZE - 3/8 thru 7/8 inch rod in 1 inch
increments.
MATERIAL - Carbon Steel.
FINISH - Plain, Electro-Galvanized and
Stainless Steel.
ORDERING - Part #, rod diameter, rod
length and finish.
2/00 8
i
#14
(Item #100-black)
Sammys 114', 318" rod
WOOD - Sammys
1III]D - 1/4" Rod (Vertical Mount)
Use Use #14 Nut Driver (Item #100)
Item # Model Shk Lgth Shk flia Box Qty Weight
(per 100) Case Qty
20 GST.750 3/4 1/4 100 4.75 1000
21 GST 100 1 1/4 100 5.00 1000
22 GST 200 2 1/4 100 6.50 1000
23 GST 300 3 1/4 100 7.50 1000
24 GST 600 6 1/4 50 9.00 500
a
E
NE
I&IIIS] I11 (Vertical Mount)
Use 'Use #14 Nut Driver (Item #100)
Approvals Item # Model Shk Lgth Shk Dia FM Test
Loa lb.
ULTest
Load lb.
UIJFM Actual Pipe Size
Pullout Box Qty
10 GST.75 3/4 1/4 564#-6Ply 100
NFPA 11 GST 10 1 1/4 2104 - 7/16 OSB100
670# - 3/4" Ply
UL-FM-NFPA 12 GST 20 2 1/4 9404 8504 3/4-2 1/2 17604 - Fir 100
UL-NFPA * 27 GST 25-380 21/2 3/8 15004 4 2113# - Fir 50
UL-FM-NFPA 13 GST 30 3 1/4 1475# 15004 3/4-4 20604 - Fir 100
NFPA 403 GST 40 4 1/4 2180# - Fir 50
NFPA 14 CST6O 6 1/4 22304- Fir 50
i
#I4SW
(Item #101-red)
Sldewlnders &
Sammys 112" rod
DII]D - 1/2" Rodr&vtii i Mount)
Use Use #I4SW Nut Driver (Item #10 1)
Item # Model Shk Lgth Shk Dia Actual Pullout Box Qty Weight
(per 100) Case Qty
8 GST2 2 1/4 1760# - Fir 50 7.00 500
* 06 GST 2.5-380 21/2 3/8 21134-Fir 50 10.00 500
15 GST3 3 1 1/4 2275#-Fir 50 10.50 500
16 JGST4 4 1 1/4 1 21804-Fir 50 10.60 1 500
17 JGST6 6 1 1/4 1 2230# - Fir 50 10.95 500
T TJI Joist/ Truss
Consult truss manufacturer for
13
recommended Installation point
Joist *pre_drilling may be required
for items #27 and #06.
Tools available on page 9.
num 2" imbedment into base For vertical use.
Hal for NFPA 13 compliance Install In center
of lowerface.
Notices than
?" nominal width
(1112")
Page 4
1Lk
Note: Screws muss be installed with appropriate nut driver to comply with warranty
I!(IIS] Vii Rod ri : 1!rwiLflIh1 IITTTTTh
Use #14SW Nut Driver (Item #101)
Item# Model ShkLgth Shk Dia I Actual
'Shear/PuIlout
I Box Qty I Weight Case Qty (per 100)
4016 SWG100 1 1/4 I 100 7.50 1000
300 SWG200 2 1/4 1725# - Fir 100 8.00 1000
I%x.I.i,ck: Rod ri : ru; riiinflIk iTfl1Th
Use #14SW Nut Driwr (Item#101)
___
Approvals Item # Model Shk Lgth Shk Dia UL Test
Load lb.
UIJFM
Pipe Size
Actual
Shear/Pullout Box Qty Weight
(per 100)
18 SWG10 1 1/4 100 6.00
UL•NFPA 19 SWG20 2 1/4 12504 3 1725# - Fir 100 7.00
UL•NFPA * 26 SWG25-380 21/2 3/8 1500# 4 22494- Fir 50 10.25 -
25 ISWG30 1 3 1 1/4 1 i 1 50 1 8.50
#I4SW
(Item #101-red)
Sidewinders &
Sammys 1/2" rod
#14
(item #100-black)
Sammys 1/4,3/8" rod
0% Prestressed Concrete
WOOD —Sidewinders
Not less than 2" nominal width (11/2") up
to3l/2" pipe; not less than 3" nominal
width 4"&5" pipe
Floor Joist r
TJI Joist! Truss
Consult truss manufacturer for
recommended Installation point.
*pre..drilling may be required
for item #26.
Tools available on page 9.
13
SHEETROCK
Minimum 21/2" from bottom for
branch lines. Minimum 3" from
bottom for main lines. Exception:
This requirement shall not apply to
2" or thicker nailing strips resting
on top of steel beams.
- Toggle
11i :1 4ii IE 1 t-fical
Use #14 Nut Driver (Item #100)
ltem# I Model IShk Lgthl Shk Dia Actual Pullout Box Qty Weight Case Qty (per 100)
71 SST300 3 1/4 450# Lath & Plaster 50 12.00 500 404# 2 Layers 5/8 Rock
ii :1 i (OI rYI8" Rodr(VerticalI rirrni
I Use #14 Nut Driwr (Item #100)
Item# I Model 1Shk Lgth1 Shk Dia Actual Pullout Pkg Qty Weight Case Qty (per 100)
70 SST 30 3 1/4 450# Lath & Plaster 50 12.00 500 404# 2 Layers 5/8 Rock
Note: Screws must be installed with appropriate nut driver to comply with warranty Page 5