Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
5803 NEWTON DR; ; FA080035; Permit
1/9/25, 9:27 AM FA080035 Permit Data City of Carlsbad Fire Alarm Permit Job Address: 5803 NEWTON DR Permit Type: FALARM Parcel No: 2121304800 Lot #: 0 Reference No.: Permit No: FA080035 Status: ISSUED Applied 6/5/2008 Approved: 6/9/2008 Issued: 6/9/2008 PC #: Inspector: Project Title: REXFORD NEWTON BUILDING 2 FIRE ALARM INSPECTIONS @ $65/EA Applicant: JJJ ENTERPRISES 533 S VINEWOOD ST ESCONDIDO CA 760-747-3050 Owner: RI FIVNEWTON L L C 11620 WILSHIRE BLVD #300 LOS ANGELES CA Fees ($) Add'I Fees ($) Total ($) Balance ($) 130 0 130 0 about:blank 1/1 'Iii, T9E! FIRE ALARM - SECURITY - LOW VOLTAGE SYSTEMS These plans have been reviewed for apparent conIianee with the current applicable codes and standards in force in the jurisdiction. The, owner orsonlrselor may utilize 'his review in support of at) application for a building permit with the express understanding that this review in no way relieves the owner or contractor or their professional engineer or architect the .cte rcsptsssliility for full compliance with said codes and standards, including the budding codeiw for any responsibilty for deficiencies, errors. omissions or hegtigenee in these plans whether or not noted in this review. Date: Revicwer:,t1 RECOMMEND APPROVAL lal 0 RECOMMEND APPROVAL. AS NOTED REXFORD NEWTON BUILDING 5803 NEWTON DRIVE CARLSBAD, CA 92011 FIRE SPRINKLER MONITORING SYSTEM APPRrr AS SUBMITTED CARL4B FIRE DEPARtMENT REXFOR NEWTON BUILDING 5803 NEWTON DRIVE CARLSBAD CA, 92011 BILL OF MATERIALS NOTIFIER FIRE WARDEN -50 ADDRESSABLE FACP CSFM# 7165-0028:239 NOTIFIER N-ANN-80 CHARACTER LCD SERIAL ANNUNCIATOR CSFM# 7120-0028.240 NOTIFIER NP-100 ADDRESSABLE DETECTOR CSFM# 7272-0028:231 NOTIFIER NMM-1001? MONITOR MODULE CSFM# 7300-0028:230 NOTIFIER NH-100 INTELLIGENT ADDRESSABLE HEAT DETECTOR CSFM# 7270-0028.234 NOTIFIER NOT-BGI2LX MANUAL PULL STATION CSFM# 7150-0028:199 NOTIFIER NC-IOOR CONTROL AND RELAY MODULES CSFM# 7300-0028:230 WHEELOCK A524, MCW HORN /STROBE MULTI CANDELA WALL MOUNT CSFM# 7125-0785:131 DN-7102:A Al-GO FireWarden.50(E) NOTE F E Intelligent Addressable FACP with Built-In Communicator by Honeywell ----- a General The NOTIFIER FireWarden-50 NFW-50 is a Fire Alarm Control Panel (FACP) and Digital Alarm Communicator/Transmitter (DACT) combined into one circuit board. This compact, intelli- gent addressable control panel supports up to 50 addressable devices in any combination of detectors or modules. With an extensive list of powerful features, the FireWarden-50 pro- grams just like FireWarden-100 products, yet fits into applica- tions previously served only by conventional panels. The FireWarden-50's integral DACT transmits system status (alarms, troubles, AC loss, etc.) to a Central Station via the public switched telephone network. The power supply and all electronics are contained on a single circuit board supported on a new quick install chassis and housed in a metal cabinet. Available accessories include remote annunciators and reverse polarity/city box transmitter. (4XTM) NOTE: Unless otherwise specified, the term Fire Warden-50 is used in this data sheet to refer to both the Fire Warden-50 and the Fire Warden-50(E) FACPs. Features Listed to UL Standard 864, 9th edition. Auto-program (learn mode) reduces installation time. Reports two devices set to the same address. On-board DACT. 2O software zones. Two independently programmable Style Z (Class A) or Style V (Class B) NAC circuits. Selectable strobe synchronization for System Sensor, Wheelock, and Gentex devices. Remote Acknowledge, Silence, Reset and Drill via address- able monitor modules. Two programmable relays and one fixed trouble relay. Integral 80-character LCD display with backlighting. Real-time clock/calendar with automatic daylight savings control. History file with 500 event capacity. Detector sensitivity test capability (NFPA 72 compliant). Maintenance alert warns when smoke detector dust accu- mulation is excessive. One person audible or silent walk test with walk-test log and printout. Point trouble identification. Waterflow (nonsilenceable) selection per monitor point. System alarm verification selection per detector point. PAS (Positive Alarm Sequence) and Pre-signal per point (NFPA 72 compliant). Up to eight ANN-BUS annunciators. SLC COMMUNICA TION LOOP: Single addressable SLC loop which meets NFPA Style 4, 6 and 7 requirements. 50 addressable device capacity (any combination of addressable detectors and modules). Compatible wti NOTIFIER FireWarden addressable devices (refer to The FreWarden SLC Wiring Manual). NOTIFICATION A DFLIANCE CIRCUITS (NACS): Two ndependently programmable output circuits. Circuits can be configured for the following outputs: — Style Y (Class B) —StjJeZ(ClassA) - Door Holder 5er,ice - Aux Power Source Silence Inhibit and Autosilence timer options. Conthuous, March Time, Temporal or California code for main circuit board NACs with two-stage capability. Selectable strobs synchroiization per NAC. 2.5 A total power for NACs. NOTE: Maximum or totl 24VJC system power shared between all NAG circuits and be ANN-BUS !s 2.7 A. PROGRAMMING AND SOFTWARE: ALtop'rogram (learn mode) reduces installation time. Custom English Isbels (per point) may be manually entered or selected from an internal library file. Two programmabe orm-C relay outputs. 20 sotware zones. Continuous fire p otection! Juring online programming at the front panel. Program Check autcmatically catches common errors not linked to any zone o input point. DN-7102:A. 04/09/07 - Page 1 of 4 User interface LED INDICATORS AC Power (green) Fire Alarm (red) Supervisory (yellow) Trouble. (yellow) Alarm Silenced signals (yellow) KEYPAD 16 key alpha-numeric pad. Acknowledge/Step Alarm Silenced Drill (Manual Evacuate) Reset (lamp test) Ordering Options NFW-50(E): Combination DACT/Fire Alarm Control Panel with one SLC loop. Includes main circuit board with display, chassis with transformer, backbox with door, plastic bag con- taining screws, cables, key, etc., manual. NFW-50R: Same as NFW-50, with red backbox and door. DP-51050B: Optional dress panel for the Fire Warden-SO. TR-CE-B: Trim Ring for semi-flush mounting. BB-26: Battery backbox, holds up to two 25 AH batteries and CHG-75. NFS-LBB: Battery box, houses two 55 AH batteries CHG-75: Battery charger for lead-acid batteries with a rating of 25 to 75 AH. BAT Series: Batteries, see data sheet DN-6933. PRTIPK-CABLE: Cable printer/personal computer interface cable. PRN-6: UL listed compatible event printer. Uses tractor-fed paper. OPTIONAL MODULES 4XTM Reverse Polarity Transmitter Module: Provides a supervised output for local energy municipal box transmitter, alarm and trouble. Includes a disable switch and disable trou- ble LED. COMPA TIBLE ANNUNCIA TORS N-ANN-80: Remote LCD annunciator mimics the FACP dis- play N-ANN-I/O: Input/Output Module for driving graphic annunci- ators or relays N-ANN-S/PG: Serial/Parallel Printer Interface module for con- necting printer to FACP ADDRESSABLE DEVICES All feature a polling LED and rotary switches for addressing. NI-100: Addressable low-profile ionization smoke detector. NP-100: Addressable low-profile photoelectric smoke detec- tor. NP-lOOT: Addressable low-profile photoelectric smoke detec- tor with thermal sensor. NH-100: Fast-response, low-profile heat detector. NH-100R: Fast-response, low-profile heat detector with rate- of-rise option. ND-100: Photoelectric low-flow duct smoke detector. ND-IOOR: Photoelectric low-flow duct smoke detector with relay option. NMM-100: Addressable Monitor Module for one zone of nor- mally-open dry-contact initiating devices. Mounts in standard 4.0" (10.16 cm.) box. Includes plastic cover plate and end-of- line resistor. Module may be configured for either a Style B (Class B) or Style D (Class A) IDC. NDM-100: Dual Monitor Module. Same as NMM-100 except it provides two Style B (Class B) only lDCs. NMM-100P: Miniature version of NMM-100. Excludes LED and Style D option. Connects with wire pigtails. May mount in device backbox. NZM-100: Similar to NMM-100, but may monitor up to 20 con- ventional two-wire detectors. Requires resettable 24 VDC power. Consult factory for compatible smoke detectors. NC-IOU: Addressable Control Module for one Style Y/Z (Class B/A) zone of supervised polarized Notification Appli- ances. Mounts directly to a 4.0" (10.16 cm.) electrical box. Notification Appliance Circuit option requires external 24 VDC to power notification appliances. NC-100R: Addressable relay module containing two isolated sets of Form-C contacts, which operate as a DPDT switch. Mounts directly to a 4.0" (10.16 cm.) box, surface mount using the SMBSOO. NOT-BGI2LX: Addressable manual pull station with interface module mounted inside. N100-ISO: Fault Isolator Module. SMB500: Used to mount all modules except the NMM-100P. NZM-100-6: Six-zone interface module. Mount one or two modules in a BB-XP cabinet (optional). Mount up to six mod- ules on a CHS-6 chassis in a CAB-3/CAB-4 series cabinet. NOTE: For more information on Compatible Addressable Devices for use with the Fire Warden-50, see the following data sheets (document numbers): N100-ISO (DN-6994), NP-100/NP-I00T (DN-6995), NI-100 (DN-6996), NH-100/NH-I0OR (DN-6997), ND- 100/ND- IOOR (DN-7006), NMM- 100/NMM-IOOP/NDM-100/NZM- 100 (DN-6999), NC-100/NC-100R (DN-7000), and NOT-BGI2LX (DN-7001). ADDRESSABLE DEVICE ACCESSORIES End-of-Line Resistor Assembly (R-47K and R-3.9K): 47k ohm supervises the NMM-100, NDM-100, NMM-100P, and NC-100 module circuits. 3.9k ohm End-of-Line Resistor assembly supervises the NZM-100 module circuit. These resistors are included with each module. Power Supervision Relay: Supervises the power to 4-wire smoke detectors and notification appliances. N-ELR Mounting Plate: Single End-of-Line resistor plate required for use in Canada. Page 2 of 4— DN-7102:A 04/09/07 Wiring Requirements While shielded wire is not required, it is recommended that all SLC wiring be twisted-pair to minimize the effects of electrical inter- ference. Wire size should be no smaller than 18 AWG (0.78 mm2) and no larger than 12 AWG (3.1 mm2). The wire size depends on the length of the SLC circuit. Use the following table to determine the specific wiring requirements for the SLC. (Refer to the panel manual for complete details.) CIRCUIT CONNECTIONS WIRE REQUIREMENTS Circuit Type Circuit Function Wire Type and Limitations Recommended Max. Distance Wire Gauge and Compatible Brands Feet (meters) 12 AWG (3.25 mm2): Genesis 4410, Signal 98230, Belden 9583, WPW999 14 AWG (2.00 mm2):Genesis 4408 & 4608 Twisted, shielded pair Signal 98430, Belden 9581, WPW995 40 ohms maximum per 10,000 (3,000 m) 16 AWG (1.30 mm2): Genesis 4406 & 4606 length of Style 6 and 7 8,000 (2,400 m) Signal 98630, Belden 9575, WPW991 loops. 40 ohms per branch 4,875 (1,450 m) Direct Burial Cable Isotec maximum for Style 4 loops 3,225 (980 m) NP713110VNQ-S 18 AWG (0.75 mm2): Genesis 4402 & 4602 Connects to Signal 98300, Belden 9574, \NPW975 SLC loop Addressable . Direct Burial Cable Isotec (power-limited) Devices NP714110VNQ-S 12 AWG (3.25 mm2): Belden 5020UL & 6020UL, Genesis WG-4315 & WG-4515 Twisted, unshielded pair 10,000 (3,000 m) 14 AWG (2.00 mm2):Belden 5120UL & 40 ohms maximum per length of Style 6 and 7 8,000 (2,400 m) 6120UL, Genesis WG-4313 & WG-4513 loops. 40 ohms per branch 4,875 (1,450 m) 16 AWG (1.30 mm2): Belden 5220UL & maximum for Style 4 loops 3,225 (980 m) 6220UL, Genesis WG-4311 & WG-4511 18 AWG (0.75 mm2): Belden 5320UL & _____ _______________ 6320UL,_ Genesis _WG-4306_&_WG-4506 Untwisted, unshielded 3,000 (900 m) 12-18 AWG (3.25 -0.75 mm2) using listed _____ ______ pair1 wire ANN-BUS Connects to Twisted, shielded pair with (EIA-485) annunciator mod- a characteristic imped- 6,000 (1.800 m) 18 AWG (0.75 mm2) (power-limited) ules ance of 120 ohms ElA-232 Connects to (power-limited) remote PC com- Twisted, shielded pair 50 (15 m) 18 AWG (0.75 mm2) minimum puter Maximum loop wire resis- monitor module (power-limited) Initiating Device Circuit tance is 40 ohms for the MMF-300 and 20 ohms for 2,500 (760 m) 12-18 AWG (3.25 -0.75 mm2) the MMF-301 No more than a 2.4 volt monitor module (power-limited) Initiating Device Circuit drop allowed at end of cir- cuit. Maximum loop wire 2,500 (760 m) 12-18 AWG (3.25 -075 mm2) resistance is 25 ohms control module Notification Appli- In alarm, no more than a Distance limitation set by 1.2 volt (power-limited) ance Circuit 1.2 volt drop allowed at maximum line 12-18 AWG (3.25 - 0.75 mm2) end of circuit drop 1) When using untwisted, unshielded wire, full conduit is recommended for optimum EMI/RFI protection. DN-7102:A 04/09/07 - Page 3 of 4 SYSTEM SPECIFICATIONS System Capacity , Temperature and Humidity Ranges Intelligent Signalling Line Circuits.......................................1 Addressable device capacity ............................................50 Programmable software zones .........................................20 Annunciators ......................................................................8 Electrical Specifications AC Power: FireWarden-50: 120 VAC, 60 Hz, 0.3 A. FireWar- den-50E: 240 VAC, 50 Hz, 0.15 A. Wire size: minimum 14 AWG (2.00 mm2) with 600 V insulation. Nonpower-limited, supervised. Battery: Two 12 V 18 AH lead-acid batteries. Battery Charger Capacity: 7-18 AH (FireWarden-50 cabinet holds maximum of two 18 AH batteries.) Communication Loop: Supervised and power-limited. Notification Appliance Circuits: Terminal Block provides connections for two NACs, Style Y (Class B) or. Style Z (Class A). Special Application power. Power-limited, supervised cir- cuitry. Maximum signaling current per circuit: 2.5 A. End-of- Line Resistor: 4.7 kohm, V2 watt (P/N 71252 UL listed) for Style V (Class B) NAC. Refer to the NOTIFIER Device Compatibility Document for listed compatible devices. Two Programmable Relays and One Fixed Trouble Relay: Contact rating: 2.0 A @ 30 VDC (resistive), 0.5 A @ 30 VAC (resistive). Form-C relays, nonpower-limited, nonsupervised. Cabinet Specifications Door: 19.26" (48.92 cm.) high x 16.82" (42.73 cm.) wide x 0.72" (1.82 cm.) deep. Backbox: 19.00" (48.26 cm.) high x 16.65" (42.29 cm.) wide x 5.25" (13.34 cm.) deep. Trim Ring (TR-CE): 22.00" (55.88 cm.) high x 19.65" (49.91 cm.) wide. Shipping Specifications Weight: 26.9 lbs. (12.20 kg.) Dimensions: 20.00" (50.80 cm.) high x 22.5" (57.15 cm.) wide x 8.5" (21.59 cm.) deep. This system meets NFPA requirements for operation at 0 - 49°C132 - 120°F and at a relative humidity 93% ± 2% RH (noncondensing) at 32°C ± 2°C (90°F ± 3°F). However, the useful life of the system's standby batteries and the electronic components may be adversely affected by extreme tempera- ture ranges and humidity. Therefore, it is recommended that this system and its peripherals be installed in an environment with a normal room temperature of 15.- 27°C/60 - 80°F. NFPA Standards The FireWarden-50(E) complies with the following NFPA 72 Fire Alarm Systems requirements: - LOCAL (Automatic, Manual, Waterfiow and Sprinkler Supervisory). - AUXILIARY (Automatic, Manual and Waterfiow) (requires 4XTM). - REMOTE STATION (Automatic, Manual and Waterfiow) (Where a DACT is not accepted, the alarm, trouble and supervisory relays may be connected to UL 864 listed transmitters. For reverse polarity signaling of alarm and trouble, 4XTM is required.) - PROPRIETARY (Automatic, Manual and Waterfiow). - CENTRAL STATION (Automatic, Manual and Waterfiow, and Sprinkler Supervised). Agency Listings and Approvals The listings and approvals below apply to the basic FireWar- den-50 control panel. In some cases, certain modules may not be listed by certain approval agencies, or listing may be in pro- cess. Consult factory for latest listing status. UL: S635 FM approved CSFM: 7165-0028:239 NOTIFIER®. FireWarden®, and System Sensor® are registered trade- marks of Honeywell International Inc. Microsoft® and Windows® are regis- tered trademarks of the Microsoft Corporation. ©2007 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited. I SO 9001 This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. dl We cannot cover all specific applications or anticipate all requirements. ENGINEERING & MANUFACTURING All specifications are subject to change without notice. QUALITY SYSTEMS Made in the U.S. A. For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118. www.notifier.com Page 4 of 4— DN-7102:A• 04109/07 CALIF ORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7165-0028:239 Page 1 of 1 CATEGORY: Control Unit (Non High-Rise) LISTEE: Notifier, One Fire-Lite Place, Northford, CT 06472-1653 Contact: Lawrence T. Flood (203) 484-6302 FAX (203) 484-7309 DESIGN: Model FireWarden-50 addressable fire alarm control unit. Unit consists of one communication loop, two bell circuits, and three relay contact outputs for alarm, trouble and supervisory. Local, auxiliary, remote station, central station and proprietary (protected premise), automatic, manual, water flow and sprinkler supervisory service. Refer to listee's data sheet for detailed product description, operational considerations and required/optional accessories. When required, accessories shall be CSFM listed. RATING: 120 VAC, 60 Hz, 3.0 A Primary, 24 VDC Secondary INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listees name, model number, electrical rating and UL label. APPROVAL: Listed as an addressable fire alarm control panel for use with separately listed compatible initiating and indicating devices. Refer to listee's Installation Instruction Manual for details. This control unit can generate a distinctive three-pulse Temporal Pattern Fire Alarm Evacuation Signal (for total evacuation) in accordance with NFPA 72, 2002 Edition. This control unit meets the requirements of UL-864, 9th Edition Standard. NOTE: For Fire Alarm Verification Feature (delay of fire alarm signal), the maximum Retard/Reset/Restart period shall not exceed 30 seconds. XLF: 7165-0075:210 10-03-2006 jw This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed, This listing should not be used to verify correct operational requirements or installation V criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources, Date Issued: DECEMBER 14, 2007 Listing Expires June 30, 2008 Author/zed By: MIKE TANAKA, Senior Deputy State Fire Marshal Program Manager N-ANN-80 80-Character LCD Serial Annunciator ETITI: General DN-7114:A A1-65 The N-ANN-80 Annunciator is a compact, backlit, 80-character LCD fire annunciator that mimics the Fire Alarm Control Panel (FACP) display. It provides system status indicators for AC Power, Alarm, Trouble, Supervisory, and Alarm Silenced condi- tions. The N-ANN-80 and the FACP communicate over a two- wire serial interface employing the ANN-BUS communication format. Connected devices are powered, via two additional wires, by either the host FACP or a remote UL-listed, filtered power supply. The N-ANN-80 displays English-language text of system point information including device type, zone, independent point alarm, trouble or supervisory status, as well as any custom alpha labels programmed into the control panel. It includes con- trol switches for remote control of critical system functions. (A keyswitch prevents unauthorized operation of the control switches.) Up to eight N-ANN-805 may be connected to the ANN-Bus of each FACP. Minimal programming is required, which saves time during system commissioning. The N-ANN-80 is compatible with NOTIFIER FACPs with an ANN-Bus, such as the NFW-50. Features Backlit 80-character LCD display (20 characters x 4 lines) Mimics all display information from the host panel. Control switches for System Acknowledge, Signal Silence, Drill, and Reset. Control switches can be independently enabled or disabled at the FACP. Keyswitch enables/disables control switches and mechani- cally locks annunciator enclosure Keyswitch can be enabled or disabled at the FACP. Enclosure supervised for tamper. System status LEDs for AC Power, Alarm, Trouble, Supervi- sory, and Alarm Silence. Local sounder can be enabled or disabled at the FACP. N-ANN-80 connects to the ANN-BUS terminal on the FACP and requires minimal panel programming. Displays device type identifiers, individual point alarm, trou- ble, supervisory, zone, and custom alpha labels. Time-and date display field. Aesthetically pleasing design constructed of durable Lexan. Surface mount directly to wall or to single, double, or 4" square electrical box. Semi-flush mount to single, double, or 4" square electrical box. Can be remotely located up to 6,000 feet (1,800 m) from the panel. Backlight turns off during AC loss to conserve battery power but will turn back on if an alarm condition occurs. May be powered by 24 VDC from the host FACP or by remote power supply (requires 24 VDC). Up to eight N-ANN-80s can be connected on the ANN-BUS. Controls and Indicators AC Power Alarm Trouble Supervisory Alarm Silenced Specifications Operating voltage range: 18 VDC to 28 VDC Current consumption © 24 VDC nominal (filtered and non- resettable): 40 mA maximum. Ambient temperature: 32°F to 120°F (0°C to 49°C). Relative humidity: 93% ± 2% RH (noncondensing) at 32°C ± 2°C (90°F ± 3°F). 5.375" (13.65 cm.) high x 6.875" (17.46 cm.) wide x 1.375" (3.49 cm.) deep. For use indoors in a dry location. All connections are power-limited ar.d supervised. Agency Listings and Approvals The listings and approvals below apply to the N-ANN-80. In some cases, certain modules may not be listed by certain approval agencies, or listing may be in process. Consult factory for latest listing status. UL: S635. FM approved CSFM: 7120-0028:240 The ANN-BUS POWERING THE DEVICES ON THE ANN-BUS FROM AUXILIARY POWER SUPPLY The ANN-BUS can be powered by an auxiliary power supply when the maximum number of ANN-BUS devices exceeds the ANN-BUS power requirements, See the FACP manual for more information. - DN-7114'A•03/21/07—Page I 0f2 ANN-BUS DEVICE ADDRESSING Each ANN-BUS device requires a unique address (ID Number) in order to communicate with the FACF. A maximum of 8 devices can be connected to the FACP ANN-BUS communication circuit. See the FACE manual for more information. WIRE REQUIREMENTS: COMMUNICATIONS CIRCUIT The N-ANN-80 connects to the FACE ANN-BUS communica- tions circuit. To determine the type of wire and the maximum wir- ing distance that can be used with FACE ANN-BUS accessory modules, it is necessary to calculate the total worst case current draw for all modules on a single 4-conductor bus. The total worst case current draw is calculated by adding the individual worst case currents for each module. NOTE: For total worst case current draw on a single ANN-BUS refer to appropriate FACP manual. After calculating the total worst case current draw, the following table specifies the maximum distance the modules can be located from the FACE on a single wire run. The table ensures 6.0 volts of line drop maximum. In general, the wire length is lim- ited by resistance, but for heavier wire gauges, capacitance is the limiting factor. These cases are marked in the chart with an asterisk (*). Maxi- mum length can never be more than 6,000 feet (1,800 m), regardless of gauge used. See table below. WIRE REQUIREMENTS: POWER CIRCUIT 14 to 18 AWG (0.75 - 2.08 mm 2) wire for 24 VDC power cir- cuit is acceptable. All connections are power-limited and supervised. A maximum of eight N-ANN-80 modules may be connected to this circuit. Communication Pair Wiring Distance: FACP to Last ANN-BUS Module Total Worst Case Current Draw (amps) 22 Gauge 18 Gauge 16 Gauge 14 Gauge 0.100 1,852 ft. 4,688 ft. * 6,000 ft. *6,000 ft. 0.200 926 ft. 2,344 ft. 3,731 ft. 5,906 ft. 0.300 617 ft. 1,563 ft. 2,488 ft. 3,937 ft. 0.400 463 ft. 1,172ft. 1,866 ft. 2,953 ft. 0.500 370 ft. 938 ft. 1,493 ft. 2,362 ft. 0.600 309 ft. 781 ft. 1,244 ft. 1,969 ft. 0.700 265 ft. 670 ft. 1,066 ft. 1,687 ft. 0.800 231 ft. 586 ft. 933 ft. 1,476 ft. 0.900 206 ft. 521 ft. 829 ft. 1,312 ft. 1.000 (max.) 185 ft. 469 ft. 746 ft. 1,181 ft. WIRING CONFIGURATION The following figure illustrates the wiring between the FACE and ANN-BUS devices. ANN-BUS and power wiring are supervised and power-limited. ~~A ANN-BUS Device Eel NEW-SO T83 1 2 3 4 56 7 8 FACP Wiring to ANN-BUS Device LEXAN® is a registered trademark of GE Plastics, a subsidiary of General Electric Company. ©2007 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited. This document is not intended to be used for installation purposes. ISO 9001 We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. INGINERINI U MANUFACTURING All specifications are subject to change without notice. -- QUALITY SYSTEMS Made in the U.S.A, - For more information, contact Notifier. Phone: (203) 484-7161 FAX: (203) 484-7118. - www.notifier.com Page 2of2—DN-7114:A•03121/07 - CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7120-0028:240 Page 1 of 1 CATEGORY: Annunciators LISTEE: Notifier, One Fire-Lite Place, Northford CT 06472-1653 Contact: Lawrence T. Flood (203) 484-6302 FAX (203) 484-7309 DESIGN: Model N-ANN-80 remote fire annunciator. Unit is a 80-character, supervised backlit LCD fire annunciator. Communication between the control panel and the annunciator is accomplished over a two-wire serial interface employing the ANN-BUS protocol. Refer to listees data sheet for additional detailed product description and operational considerations. INSTALLATION: In accordance with listees printed installation instructions, applicable codes & ordinances and in manner acceptable to the authority having jurisdiction. MARKING: Listee's name, product number, electrical rating and UL label. APPROVAL: Listed as an annunciator for use separately listed compatible fire alarm control units Refer to manufacturer's installation manual for details. XLF: 7120-0075:211 10-03-2006 jw This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources. Date Issued: JUNE 4, 2007 Listing Expires June 30, 2008 Authorized By.. MIKE TANAKA, Senior Deputy State Fire Marshal Program Manager by Honeywell GENERAL The NP-100 and NP-100T addressable, low-profile plug- in photoelectric detectors use a state-of-the-art photoeldc- trio sensing chamber with communications to provide open area protection and are used exclusively with NOTIFI ER's FireWarden-1 00 Addressable Fire Alarm Con- trol Panel (FACP). The NP-100T adds thermal sensors that will alarm at a fixed temperature of 135°F (57°C). Since these detectors are addressable, they will help emergency personnel quickly locate a fire during its early stages, potentially saving precious rescue time while also reducing property damage. Two LEDs on each sensor light to provide a local, visible sensor indication. Remote LED annunciator capability is available as an optional accessory (PIN RA400Z). SLC loop: * Two-wire loop connection. Unit uses base for wiring. Addressing: Addressable by device. Direct Decade 01 - 99 (FireWarden-100) entry of ad- dress. Architecture: Unique single-source, dual-chamber design to respond quickly and dependably to a broad range of fires. Sleek, low-profile design. Integral communications and built-in type identification. Built-in tamper-resistant feature. Removable cover and insect-resistant screen for simple field cleaning. Operation: Withstands air velocities up to 4,000 feet-per-minute (20 rn/sec.) without triggering a false alarm. Factory preset at 1.5% nominal sensitivity for panel alarm threshold, level. Visible LED "blinks" when the unit is addressed (com- municating with the fire panel) and latches on in alarm. Mechanicals: Sealed against back pressure. Direct surface mounting of, electrical box mounting. Mounts to: single-gang box, 3.5" (8.89 cm) 0r4.0" (10.16 cm) octagonal box, or 4.0" (10.16 cm) square electrical box (using a plaster i't'ng - included). Other system features: Fully coated circuit boards and superior HF/transient June 15 2005 DN-6995 Al -310 NP-1 00 and NP-lOOT Addressable Photoelectric Detectors Section: Addressable 1J (77 _ -,j State Marshal <&> 72/2-0028:231 ' LISTED APPROVED S1115 MARYLAND M E State Fire Marsha' Permit 4/ 2173 243-02-E Vol. II with B7IOLP base 6934ph.. pg NP-lOOTwith B71OLPbase . 6935pho1jpg protection. 94-VU plastic flammability rating. Low standby current. Options: Remote LED output connection (PIN RA400Z). SPECIFICATIONS Voltage range: 15-32 VDC (peak). Standby current: 300 pA © 24 VDC. LED current: 6.5 mA @ 24 VDC (latched "ON"). Air velocity: 4,000 ft/mm. (20 rn/sec.) maximum. Diameter: 6.1' (15.5 cm) installed in B71OLP base. Height: 2.1 (5.33 cm) installed in B71OLP base. Weight: 3.6 oz. (102 g). Operating temperature range: for NP-100: 0°C 10 49'c. (32°F to 120"F): for NP-100T.- 0°C to 38-C (32°F to 100 'F Temperature: 0rC - 49°C (32°F - 120F). Relative humidity: 10% - 93%, non-condensing. This document is not intended to he used for installation purposes. we try io keep our roduci information up-to-date and accurate We cannoi cover alt specific appirratroes or anhcry'e ire all reriurrerneri is. OH specificairons are Subject to change virihosi notice. For more niormatron, c00i55 NOTIFIER. Phone' (203) 484'715' FAX. 12021 484-71i8 N OTI F ER' . ENGINEERING & MANUFACTURING by Honeywell 12 Oirr,lonvi'ie React, i'iorihnr:'i Connecticut 06472 QUALITY SY STEMS ............-.-:., UN-6995 • 06/15/05 - Page 1 Of Use Photoelectric detectors in life-safety applications to provide a broad range of fire-sensing capability, espe- cially where smoldering fires are anticipated. Ionization detectors are often better than photoelectric detectors at sensing fast, flaming fires. CONSTRUCTION These detectors are constructed of oft-white LEXAN®. NP-100(T) plug-in, low-profile smoke detectors are de- signed to commercial standards and offer an attractive appearance. LEXAN® is a registered trademark of GE Plastics, a subsidiary of General Electric Company. INSTALLATI ON NP-100(T) plug-in detectors use a detachable mounting base to simplify installation, service and maintenance. Mount base on box which is at least 1.5 inches (3.81 cm) deep. Suitable boxes include: 4.0" (10.16 cm) square box with plaster ring. 4.0' (10.16 cm) octagonal box. 3.5" (8.89 cm) octagonal box. Single-gang box. NOTE: Because of the inherent supervision provided by the SLC loop, end-of-line resistors are not required. Wiring "T- taps' or branches are permitted for Style 4 (Class B) wiring. [.j.4i71j•[sJ Each NP-100(T) uses one of 99 possible addresses on the FireWarden-100 Signaling Line Circuit (SLC). It re- sponds to regular polls from the system and reports its type and status. The NP-100(T) addressable photoelectric sensor's unique unipolar chamber responds quickly and uniformly to a broad range of smoke conditions and can withstand wind gusts up to 4,000 feet-per-minute (20 rn/sec.) with- out sending an alarm level signal. Because of its unipo- lar chamber, the .NP-100(T) is approximately two times more responsive than most photoelectric sensors. This makes it a more stable detector. DETECTOR SENSITIVITY TEST Each detector can have its sensitivity tested (required per NFPA 72, Chapter 7 on Inspection, Testing and Mainte- nance) when installed/connected to a FireWarden-100 addressable tire alarm control panel. The results of the sensitivity test can he printed off the FireWarden-100 for record keeping.. PRODUCT LINE INFORMATION NP-100 Addressable photoelectric detector: B71OLP base included. NP-100T Same as NP-1 00 but with thermal element; B71OLP base included.* RA400Z Remote LED. Mounts to a single-gang box. B71OLP Plug-in detector base. Dimensions: 6.1" (15.5 cm). Mounting: 4.0" (10.16 cm) square box with or without plaster ring, 4.0" (10.16 cm) octagonal box, 3.5" (8.89 cm) octagonal box, or single-gang box. All mounting boxes have a minimum depth of 1.5" (3.81 cm). B224RB Plug-in System Sensor relay detector base. Diameter: 6.2" (15.75 cm). Mounting: 4.0" (10.16 cm) square box with or without plas- ter ring, 4.0" (10.16 cm) octagonal box, or 3.5" (8.89 cm) octagonal box. All mounting boxes have a minimum depth of 1.5(3.81 cm). B22461 Plug-in System Sensor isolator detector base. Maximum 25 devices between isola- tor bases (see DN-6994). Diameter: 6.2" (15.75 cm). Mounting: 4.0" (10.16 cm) square box with or without plaster ring, 4.0" (10.16 cm) octagonal box, or 3.5" (8.89 cm) octagonal box. All mounting boxes have a minimum depth of 1.5" (3.81 cm). B501BH Plug-in System Sensor sounder detector base. Diameter: 6.0" (15.24 cm). Mounting: 4.0" (10.16 cm) square box with or without plaster ring. Mounting box has a minimum depth of 1.5" (3.81 cm). *Prior to 03/28/05, the B71OLP base was sold separately Page 2 01 2 -- DN-6995 0515/05 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7272-0028:231 Page 1 of 1 CATEGORY: Photoelectric Smoke Detector LISTEE: Notifier, One Fire-Lite Place, Northford, CT 06472-1653 Contact: Lawrence Flood (203) 484-1200 FAX (203) 484-7309 DESIGN: Models NP-100 and NP-100T photoelectric type smoke detectors. Model NP-100T has a 1350F supplement integral heat sensor which only assists in a fire situation. The purpose of this thermal circuitry is to increase the sensitivity of the detector. This thermal circuitry is NOT approved for use as a heat detector. Refer to listee's printed data sheet for additional detailed product description and operational considerations. RATING: 24VDC INSTALLATION: In accordance with listee's printed installation instructions, applicable codes & ordinances and a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating and UL label. APPROVAL: Listed as photoelectric smoke detector for use with separately listed compatible fire alarm control units. All units are suitable for installation inside air duct with a maximum air velocity of 4000 fpm. Refer to listee's Installation Instruction Manual for details. NOTE: The photoelectric type detectors are generally more effective at detecting slow, smoldering fires, which smolder for hours before bursting into flames. Sources of these fires may include cigarettes burning in couches or bedding. The ionization type detectors are generally more effective at detecting fast, flaming fires, which consume combustible materials rapidly and spread quickly. Sources of these fires may include paper burning in a waste container or a grease fire in the kitchen. XLF 7272-0075:194 11-03-2004 This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources. Date Issued: JUNE 4, 2007 Listing Expires June 30, 2008 Authorized By: MIKE TANAKA, Senior Deputy State Fire Marshal Program Manager ~1(911410TIFIER by Honeywell c.4I1 :71i Four different monitor modules are available for NOTIFIER's FireVVarden-100 intelligent fire alarm control panels to suit a variety of applications. Monitor modules are used to supervise a circuit of dry-contact input de- vices, such as conventional heat detectors and pull sta- tions, or monitor and power a circuit of Iwo-wire smoke detectors (NZM-100). NMM-100 -The NMM-100 Monitor Module is a standard- sized module (typically mounts to a 4.0 [10.16 cm] square box) that supervises either a Class A (Style D) or Class B (Style B) circuit of dry-contact input devices. NMM-IOOP - The NMM-100P is a Miniature Monitor Mod- ule (a mere 1.3 (3.302 cm) H x 2.75' (6.985 cm) W x 0.5' (1.270 cm) D) used to supervise a Class B (Style B) cir- cuit. Its compact design allows the NMM-100P to be mounted in a single-gang box behind the device it is moni- toring. NZM-100 - The NZM-100 Interface Module is a stan- dard-sized module used to monitor and supervise com- patible two-wire, 24 volt, smoke detectors on a Class A (Style D) or Class B (Style B) circuit. NDM-100 - The NDM-100 Dual Monitor Module is a stan- dard-sized module (typically mounts to a 4.0 [10.16 cm] square box) that supervises two Class B (Style B) circuits of dry-contact input devices. NMM..iOO MONITOR MODULE Built-in type identification automatically identifies this de- vice as a monitor module to the control panel. Powered directly by two-wire SLC loop. No additional power required. High noise (EMF/AFt) immunity. SEMS screws with clamping plates for ease of wiring. Direct Decade 01 - 99 (FireWarden-100) entry of ad- dress. LED flashes red during normal operation and latches on steady to indicate alarm. The NMM-100 Monitor Module is intended for use in intel- ligent, two-wire systems, where the individual address of each module is selected using the built-in rotary switches. It provides either a two-wire or four-wire Class A or Class B fault-tolerant Initiating Device Circuit (IDC) for normally- open-contact fire alarm and supervisory devices. NMM-100 Applications - Use to monitor a zone of four-wire smoke detectors, manual fire alarm pull stations. waterfiow devices, or other normally-open dry-contact alarm activation devices. May also be used to monitor normally-open supervisory devices with special supervi- sory indication at the control panel. Monitored circuit may be wired as an NFPA Style B (Class B) or Style 0 (Class D) Initiating Device Circuit. A 47K ohm End-of-Line Resistor (provided) terminates the Style B circuit. No resistor is re- June 15. 2005 DN-6999 A1-350 Addressable Monitor Modules for the FireWcirden-1 00: NMM-100, NMM-1 OOP, NZM-1 00, NDM-1 00 Section: Addressable iJJ California State Fire U1 MEA Marshal 72-01-E Vol. I -8..-$ 7300-0028:230 LISTED (except NDM-100i except NDM-100) S635 APPROVED NMM-100 and NZM-100 qLiired for supervision of the Style D circuit. Maximum IDC resistance is 1,500 ohms. NMM.100 Operation - Each NMM-100 uses one of 99 (FireWarcten-100) available module addresses on an SLC loop. It responds to regular polls from the control panel and reports its type and the status (open/normal/ short) of its Initiating Device Circuit (tDC). A flashing LED indicates that the module is in communication with the con- trol panel. The LED latches steady on alarm (subject to current limitations on the loop). NMM-100 Specifications Nominal operating voltage: 15 to 32 VDC. Maximum current draw: 5.1 mA (LED on). Average operating current: 400 pA (LED flashing). EOL resistance: 47K ohms. Temperature range: 32 -F to 120F (0 C to 49'C). Humidity range: 10 4. to 93% noncondensing. Dimensions: 4.5 (11.43 cm) high x 4.0' (10.16 cm) wide x 1.25' (3.175 cm) deep. Mounts to a 4.0 (10.16 cm) square x 2.125' (5.398 cm) deep box. This document is not intended io be used for installation purposes. NO try to keep our prodi.ict uioimation up-to-date and accurate. We cannot corer all spectic applications Or anticipate all requireiz 0fl15 All specifications are subject to change without notice. For more information contact NOTIFIER. Phone 203) 484-7161 FAX: (203) 484-7118 NOTIFIER' by Honeywell 12 Ghniore'ifle Road Northford, Connecticut 06472 IS09001 KZE3 Id1 LLJ ENGINEERING MANUFACTURING QUALITY SYSTEMS DN-699.9 06115/05 - Pane 1 of 3 Built-in type identification automatically identifies this de- vice as a monitor module to the FireWarden-100. Powered directly by two-wire SLC Loop. No additional power required. High noise (EMF/RFl) immunity. Tinned. stripped leads for ease of wiring. Direct-dial entry of address (01-99 for FireWarden-100). The NMM-100P Mini Monitor Module can be installed in a single-gang unction directly behind the monitored unit. Its small size and light weight allow it to be installed without rigid mounting. The NMM-100P is intended for use in in- telligent, two-wire systems where the individual address of each module is selected using rotary switches. It pro- vides a two-wire initiating device circuit for normally-open- contact fire alarm and security devices. 14/5 Pi ADDRESS: 13, 2 2 1 2/7 / -/ — ......... LOOP (/ 11102, LI - 6 TENS ONES 01 LU Uj N MM-lOOP Applications - Use to monitor a single device or a zone of four-wire smoke detectors, manual fire alarm pull stations, waterflow devices, or other normally- open dry-contact devices. May also be used to monitor nor- mally-open supervisory devices with special supervisory indication at the control panel. Monitored circuit/device is wired as an NFFA Style B (Class B) Initiating Device Cir- cuit. A 47K ohm End-of-Line Resistor (provided) terminates the circuit. NMM-10011 Operation - Each NMM-100P uses one of 99 (FireWarden-100) available module addresses on an SLC loop. It responds to regular polls from the control panel and reports its type and the status (open/normal/ short) of its Initiating Device Circuit (IDC). NMM-100P Specifications Nominal operating voltage: 15 to 32 VDC. Average operating current: 375 pA maximum. EOL resistance: 47K ohms Temperature range: 32 F to 120 F (OC to 49C). Humidity range: 10% to 93% noncondensing. Dimensions: 1.3" (3.302 cm) high x 2.75 (6.985 cm) wide x 0.5 (1.270 cm) deep. Wire length: 6.0 (15.24 cm) minimum. Supports compatible two-wire smoke detectors. Supervises IDC wiring and connection of external power source (resettable). High noise (EMF/RFI) immunity. SEMS screws with clamping plates for ease of wiring. Direct-dial entry of address (01-99 for FireVVarden-100). LED flashes during normal operation. LED latches steady to indicate alarm on command from control panel. The NZM-100 Interface Module is intended for use in in- telligent, addressable systems, where the individual ad- dress of each module is selected using built-in rotary switches. This module allows intelligent panels to inter- face and monitor two-wire conventional smoke detectors. It transmits the status (normal, open, or alarm) of one full zone of conventional detectors back to the control panel. All two-wire detectors being monitored must be UL-com- patible with the module. NZM-100 Applications - Use the NZM-100 to moni- tor a zone of two-wire smoke detectors. The monitored cir- cuit may be wired as an NFPA Style B (Class 8) or Style D (Class A) Initiating Device Circuit. A 3.9 K ohm End-of-Line Resistor (provided) terminates the end of the Style B or D (class B or A) circuit (maximum IDC loop resistance is 25 ohms). Install ELR across terminals 8 and 9 for Style D application. NZM-100 Operation - Each NZM-100 uses one of 99 (FireWarden-100) available module addresses on an SLC loop. It responds to regular polls from the control panel and reports its type and the status (open/normal/ short) of its Initiating Device Circuit (IDC). A flashing LED indicates that the module is in communication with the con- trol panel. The LED latches steady on alarm (subject to current limitations on the loop). NZM-100 Specifications Nominal operating voltage: 15 to 32 VDC. Maximum current draw: 5.1 mA (LED on). Average operating current: 270 pA (LED flashing). EOL resistance: 3.9K ohms. External supply voltage (between Terminals T3 and T4). DC voltage: 18 to 28 volts power limited. Ripple voltage: 0.1 VRMS maximum. Current: 90 mA per module maximum. Requires regulated. resettable 24 VDC power. Temperature range: 32'F to 120'F (0'C to 49C). Humidity range: 10% to 93% noncondensing. Dimensions: 4.5" (11.43 cm) high x 4.0' (10.16 cm) wide 1.25' (3.175 cm) deep. Mounts to a 4.0" (10.16 cm) square x 2.125" (5.398 cm) deep box. Page 2 of 3. DN-6999 NDMOO DUAL MONITOR MODULE Built-in type identification automatically identities this de- vice as two monitor modules to the control panel. Powered directly by the two-wire SLC loop. No additional power required. High noise (EMF!RFI) immunity. SEMS screws with clamping plates for ease of wiring. Direct-dial entry of address 01 - 99 (FireWarden-100) uses two addresses per module. LED flashes red during normal operation and latches on steady red to indicate alarm. The NDM-100 Dual Monitor Module is intended for use in intelligent, two-wire systems, where the individual address of each module is selected using the built-in rotary switches. It provides two independent two-wire fault-toler- ant Initiating Device Circuits (lDCs) at two separate, con- secutive addresses. It is capable of monitoring normally open-contact fire alarm and supervisory devices, or either normally open or normally closed devices for non-fire ap- plications. NDM-100 Applications - Use to monitor a zone of four-wire smoke detectors, manual fire alarm pull sta- tions, waterflow devices, or other normally-open dry-con- tact alarm activation devices. May also be used to monitor normally-open supervisory devices with special supervi- sory indication at the control panel. Monitored circuit may be wired as an NFPA Style B (Class B) Initiating Device Circuit. The 47K ohm End-of-Line Resistors (provided) terminate the Style B circuit. Maximum IDC resistance is 1,500 ohms. NDM-100 Operation - Each NDM-100 uses two of 99 (FireWarden-100) available module addresses on an SLC loop. It responds to regular polls from the control panel and reports its type and the status (open/normal/ short) of its Initiating Device Circuit (lDC). A flashing LED indicates that the module is in communication with the control panel. The LED latches steady on alarm (subject to current limitations on the loop). NDM-100. Specifications Nominal operating voltage: 15 to 32 VDC. Maximum current draw: 5.1 mA (LED on). Average operating current: 750 pA (LED flashing). EOL resistance: 47K ohms. Maximum IDC wire resistance: 1,500 ohms. Temperature range: 32°F to 120°F (0°C to 49°C). Humidity range: 10% to 93% noncondensing. Dimensions: 4.5" (11.43 cm) high x 4.0" (10.16 cm) wide x 1.25" (3.175 cm) deep. Mounts to a 4.0" (10.16 cm) square x 2.125" (5.398 cm) deep box. Accessories: SM13500 electrical box. I4fi1;UiIII NMM-100, NZM-100, and NDM-100 modules mount di- rectly to a standard 4.0" (10.16 cm) square, 2.125" cm) deep, electrical box. They may also be mounted to the SMB500 surface-mount box. Mounting hardware and in- stallation instructions are provided with each module. All wiring must conform to applicable local codes, ordinances and regulations. These modules are intended for POWer limited wiring only. The NMM-100P module is intended to be wired and mounted without rigid connections inside a standard electrical box. All wiring must conform to applicable local codes, ordinances and regulations. ARCHThCTS'/ENG NEERS' SPECFNCATIOS Specifications of these and all NOTIFIER products are available from NOTIFIER. PRODUCT LINE INFORMATION NMM-100 Monitor module. NMM-100P Mini monitor module. NZM-100 Two-wire detector monitor module. NDM-100 Dual monitor module. SMB500 Optional surface-mount backbox. I MOUNTING DIAGRAMS For steinekird-sized modules CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7300-0028:230 Page 1 of 1 CATEGORY: Misc. Devices/Control Unit Accessories LISTEE: Notifier, 12 Clintonville Rd, Northford CT 06472 Contact: Lawrence Flood (203) 484-1200 Fax (203) 484-7309 DESIGN: Models NMM-100P, NMM-100, and NZM-100 monitor modules; Models NC-100R and NC-100 control modules. Refer to listee's data sheet for additional detailed product description and operational considerations. RATING: 15-32VDC INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating, and UL label. APPROVAL: Listed as control unit accessories for use with listee's separately listed electrically compatible fire alarm control units. Refer to listee's Installation Instruction Manual for details. XLF: 7300-0075:185 10-20-2004 This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources. Date Issued: JUNE 4, 2007 Listing Expires June 30, 2008 Authorized By: MIKE TANAKA, Senior Deputy State Fire Marshal Program Manager June 15, 2005 DN-6997.A1-320 N NH-1 00 Series 0 OTU FU ER Intelligent Addressable Thermal by Honeywell (Heat) Detectors for FireWarden-100 Section: Addressable GENERAL The NOTIFIER NH-100 Series thermal detectors are ad- dressable sensors that use a state-of-the-art thermistor sensing circuit for fast response. These sensors are de- signed to provide open-area protection and are intended for use with the FireWarden-1 00 Fire Alarm Control Panel (FACP). Both the NH-100 and NH-100R sensors provide fixed tem- perature alarm detection at 135°F157°C. The NH-100R sensor responds to rate-of-rise conditions of greater than 15°F/8.3°C per minute. These thermal detectors provide cost effective, addressable property protection in a variety of applications. Two LEDs on each sensor light to provide a local, visible sensor indication. Remote LED annunciator capability is available as an optional accessory (PIN RA400Z). FEATURES SLC loop: Two-wire SLC loop connection. Unit uses base for wiring. Addressing: Addressable by device. Direct Decade 01 - 99 (FireWarden-100) entry of ad- dress. Architecture: Sleek, low-profile, stylish design. State-of-the-art thermistor technology for fast response. Integral communications and built-in device-type iden- tification. Built-in tamper resistant feature. Built-in functional test switch activated by external mag- net. Operation: Factory preset at 135°F (57°C). Rate-of-rise model (NH-bOA), 15°F (8.3°C) per minute. 360°-field viewing angle of the visual alarm indicators (two bicolor LEDs). LEDs blink green in Normal condi- tion and turn on steady red in Alarm. Visible LEDs "blink" every time the unit is addressed. Mechanicals: Sealed against back pressure. SEMS screws for wiring of the separate base. Designed for direct-surface or electrical-box mounting. Plugs into separate base for ease of installation and maintenance. cTTJ California M EA State Are marshal 387-02-E Vol. II 7270-0028:234 LISTED S747 APPROVED -.-----,.-. , . 6936ph01 ipg NH-100 with B7IOLP base Separate base allows interchange of photoelectric, ion- ization and thermal sensors. Other system features: Remote test feature from the panel. Walk test with address display. Low standby current. 94-5V plastic flammability rating. Options: Remote LED output connection to optional RA400Z re- mote LED annunciator. Recessed (RMK400) or surface (SMK400) base mount- ing kits. SPECIFICATIONS Diameter: 6.1" (15.5 cm) installed in B71OLP. Height: 2.1 (5.33 cm). Weight: 4.8 oz. (137 g). Installation temperature: —4°F to 100°F (-20°C to 38°C). Humidity range: 10% to 93% relative humidity (noncon- This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. For more information, contact NOTIFIER. Phone: (203)484-7161 FAX: (203) 484-7118 i Am NOTIFIER" ENGINEERING & MANUFACTURING by Honeywell 12 Clintonville Road, Northford, Connecticut 06472 QUALITY SYSTEMS DN-6997 • 06/15/05 - Page t of 2 densing). Voltage range: 15 to 32 VDC peak. Standby current: 300 pA @ 24 VDC (one communica- tion every five seconds with LED blink enabled). LED current: 6.5 mA @ 24 VDC. Mounting: B71OLP flanged base, sold separately. Fixed-temperature setpoint: 135°F (57°C). Rate-of-rise detection: responds to greater than 15°F! 8.3°C per minute. INSTALLATION NH-100 Series plug-in intelligent thermal detectors use a detachable base to simplify installation, service and maintenance. Installation instructions are shipped with each detector. Mount base (all base types) on box that is at least 1.5' (3.81 cm) deep. Suitable boxes include: 4.0° (10.16 cm) square box. 3.5" (8.89 cm) or 4.0' (10.16 cm) octagonal box. Single-gang box (except relay or isolator base). NOTE: Because of the inherent supervision provided by the SLC loop, end-of-line resistors are not required. Wiring "T- taps or branches are permitted for Style 4 (Class "B") wiring only. APPLICATIONS Use thermal detectors for protection of property. CONSTRUCTION These detectors are constructed of off-white Bayblend®. The NH-100 Series plug-in intelligent thermal detectors are designed to commercial standards and offer an at- tractive appearance. Bayblend® is a registered trademark of Bayer Corporation. OPERATION Each NH-100 Series detector uses one of 99 (FireWarden-100) possible addresses on a control panel SLC loop. It responds to regular polls from the control panel and reports its type and the status. If it receives a test command from the panel (or a local magnet test), it stimulates its electronics and reports an alarm. It blinks its LEDs when polled and turns the LEDs on when com- manded by the panel. The NH-100 Series offers features and performance that represent the latest in thermal de- tector technology. PRODUCT LINE INFORMATION NH-100 Intelligent thermal sensor; B71OLP base in- cluded.* NH-bOA Same as NH-100 with rate-of-rise feature; B71OLP base included." RA400Z Remote LED. Mounts to a single-gang box. B71OLP Plug-in detector base. Dimensions: 6.1" (15.5 cm). Mounting: 4.0' (10.16 cm) square box with or without plaster ring, 4.0" (10.16 cm) octagonal box, 3.5" (8.89 cm) octagonal box, or single-gang box. All mounting boxes have a minimum depth of 1.5" (3.81 cm). M02-04-00 Test magnet, B224RB Plug-in System Sensor relay detector base. Diameter: 6.2" (15.75 cm). Mounting: 4.0" (10.16 cm) square box with or without plaster ring, 4.0" (10.16 cm) octagonal box, or 3.5" (8.89 cm) octagonal box. All mounting boxes have a minimum depth of 1.5" (3.81 cm). 8224B1 Plug-in System Sensor isolator detector base. Maximum 25 devices between isolator bases (see DN-6994). Diameter: 6.2" (15.75 cm). Mounting: 4.0" (10.16 cm) square box with or without plaster ring, 4.0" (10.16 cm) octagonal box, or 3.5(8.89cm) octagonal box. All mounting boxes have a minimum depth of 1.5" (3.81 cm). B501 6H Plug-in System Sensor sounder detector base. Diameter: 6.0" (15.24 cm). Mounting: 4.0" (10.16 cm) square box with or without plaster ring. Mounting box has a minimum depth of 1.5" (3.81 cm). "Prior to 03/28/05, the B71OLP base was sold separately Page 2 of 2 - DN-6997 • 06/15/05 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7270-0028:234 Page 1 of 1 CATEGORY: Heat Detector LISTEE: Notifier, One Fire-Lite Place, Northford, CT 06472-1653 Contact: Lawrence Flood (203) 484-1200 FAX (203) 484-7309 DESIGN: Models NH-100, (fixed temperature) and NH-100R rate-of-rise with fixed temperature heat detectors. Refer to listee's data sheet for detailed product description and operational considerations. RATING: NH-100 135° F fixed temperature NH-100R 135° F fixed temperature and 15° F rate-of-rise INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating, and UL label. APPROVAL: Listed as heat detectors for use with separately listed compatible fire alarm control units. Refer to listee's Installation Instruction Manual for details. XLF: 7270-0075:195 11-03-2004 This listing is based upon technical data submitted by the applicant. CSFI Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer tolistee's data sheet, installation instructions and/or other suitable information sources. Date Issued: JUNE 4, 2007 Listing Expires June 30, 2008 Authorized By: MIKE TANAKA, Senior Deputy State Fire Marshal Program Manager NOTIFIER by Honeywell The NOTIFIER NOT-BG12LX is a state-of-the-art, dual- action (i.e., requires two motions to activate the station) pull station that includes an addressable interlace (mounted inside) for NOTIFIER's addressable FireWarden-100 lire alarm control panel. Because the NOT-BG12LX is addres- sable, the control panel can display the exact location of the activated manual pull station. This leads fire service personnel quickly to the location of the alarm. FEATURES Aesthetically pleasing, highly visible, dual-action design. Meets ADA 5 lb. maximum pull force. Easily operated (dual-action). Attractive shape and textured finish. Mounts, semi-flush, to a standard single-gang (2.125" [5.398 cm] minimum depth), double-gang, or 4.0" (10.16 cm) square electrical box. When the handle latches in down position, the word "AC- TIVATED" appears at the top of the handle in bright yel- low to clearly indicate the station has been operated. Key/lock reset; needs only a 1/4-turn to lock/unlock. Includes Braille text on station handle. Captive screw terminals wire-ready for easy connection to SLC loop (accepts up to 12 AWG/3.1 mm2 wire). Optional trim ring (BG-TR). Meets UL 38, Standard for Manually Actuated Signaling Boxes. Maintenance personnel can open station (for inspection and testing) without causing an alarm condition. Built-in bicolor LED, which is visible through the handle of the station, flashes red in normal operation and latches on steady red when in alarm. ENGI NEERING SPECI FICATIONS Manual Fire Alarm Stations shall be non-code, with a key- operated reset lock in order that they may be tested, and so designed that after actual Emergency Operation, they cannot be restored to normal except by use of a key. An operated station shall automatically condition itself so as to he visually detected as activated. Manual stations shall be constructed of red-colored LEXAN® (or polycarbonate equivalent) with clearly visible operating instructions pro- vided on the cover. The word FIRE shall appear on the front of the stations in white letters, 1.00 inches (2.54 cm) or larger. Stations shall be suitable for surface mounting on matching hackbox SB-10 or SB-I/O; or semi-flush mount- ing on a standard single-gang, double-gang, or 4.0' (10.16 LEXAN® is a registered trademark of GE Plastics. a subsidiary of General Electric Company. June 15, 2005 DN-7001 •A1-380 NOT-BG1 2LX Addressable Manual Pull Station for FireWarden-100 Section; Addressable Patented, U.S. Patent No. D428,351; 6,380,846 U.S. Patent Pending: 09/686,286 IVi EAAL 67-02-E Vol IV çij California State Fire i Marshal Wi 7150-0028199 LISTED ' ---- APPROVED The NOT-BG12LX Addressable Manual Pull Station cm) square electrical box, and shall be installed within the limits defined by the Americans with Disabilities Act (ADA) or per national/local requirements. Manual Stations shall be Underwriters Laboratories listed. Manual stations shall connect with two wires to one 01 the control panel SLC loops. The manual station shall, on com- mand from the control panel. send data to the panel repre- senting the state of the manual switch. Manual stations shall provide address setting by use of rotary decimal switches. ELECTRICAL SPECI FICATI ONS Normal operating voltage: 24 VDC Maximum SLC loop voltage: 28.0 VDC. This documeni is no: intenrJed to be used for insta aeon purposes. We try to keep our product information up-in-vale and accurWte We cannot cover all specific applications or' anticipate all requirements. All specifications are subject to change without notice. IS09001 For more atormation, contact NOTIFiER. Phone; 1203) 484-7161 FAX' 12031 484-7118 NOT B F B E R' ENGINEERING & MANUFACTURING by Honeywell 12 Clintonville Road,. Norihlord, Connecticut 06472 QUALITY SYSTEMS 014-7001. 06!15'05 — Papa tt 2 Maximum SLC loop current: 230 pA INSTALLATION The NOT-BG12LX can be semi-flush mounted into a single- gang, double-gang, or standard 4.0" (10.16 cm) square elec- trical outlet box, or surface mounted to the Model SB-10 or SB-I/O surface backbox. If the NOT-BG12LX is semi-flush mounted, then the optional trim ring (BG-TR) may be used. The BG-TR is usually needed for semi-flush mounting with 4.0' (10.16 cm) or double-gang boxes (not with single-gang boxes). F-i 1:11141 [I] In iJ )p TERMINAL CONNECTIONS 1 SLC (-) 2 SLC(~) Shell, door, and handle are molded of durable LEXAN® (or polycarbonate equivalent) with a textured finish. OPERATION Pushing in, then pulling down on the handle causes it to latch in the down/activated position. Once latched, the word "ACTIVATED" (in bright yellow) appears at the top of the handle, while a portion of the handle protrudes from the bot- tom of the station. To reset the station, simply unlock the station with the key and pull the door open. This action re- sets the handle; closing the door automatically resets the switch. Manual stations connect with two wires to one of the control panel SLC loops. Each manual station, on command from the control panel, sends data to the panel representing the state of the pull station switch. Two rotary decimal switches allow address settings (01-99). PRODUCT LINE INFORMATION NOT-BG12LX Dual-action addressable pull station. Includes key lock/reset feature. SB-10 Surface backbox. SB-I/O Surface indoor/outdoor backbox. BG-TR Optional trim ring Detail of BREAKAWAY TAB Back of station without door. H 15 0 13 10 5 76 0 LED ROTARY DECIMAL SWITCHES -- Cover open to show easy access to miniature monitor module, rotary switch, and UL label. Page 2 of 2 - DN-7001• 06/15.05 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7150-0028:199 Page 1 of 1 CATEGORY: Boxes/Pull Stations LISTEE: Notifier, One Fire-Lite Place, Northford CT 06472-1653 Contact: Larry Flood (203) 484*7161 FAX (203) 484-7309 DESIGN: Models NBG-12, NBG-12S, NBG-12LR, NBG-12LRA, NBG-12LAO, NBG-12LAOB, NBG- 12-LO, NBG-12L0B, NBG-12W, NBG-12LW, NBG-12NC, NBG-12WP, NBG-12LWP, NBG- 12L, NBG-12LX, NBG-12LA, NBG-12PS, NBG-12LSP, NBG-12LPS, NBG-12LPSP, NBG- 12SF, NOT-BG12LX, and *NBG 12LXSP fire alarm pull boxes. All units except Model NBG- 12S are dual action pull stations. Models NBG-12LR and NBG-12LRA are intended for agent releasing device. Refer to listee's data sheet for detailed product description and operational considerations. INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, rating, and UL label. APPROVAL: Listed as fire alarm pull boxes for use with separately listed compatible fire alarm control units. Models NBG-12WP, NBG-12LW, NBG-12W, NBG-12LWP, NBG-12LAO, NBG-12L0, NBG- 1 2LAOB and NBG-1 2LOB are intended for outdoor use when installed with Models WBB, SB- I/O, or WP-1 0 back box. Refer to listee's Installation Instruction Manual for details. Rev. 1-06-2006 jew This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed thelest results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation _J criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources. Date Issued: JUNE 4, 2007 Listing Expires June 30, 2008 Authorized By; MIKE TANAKA, Senior Deputy State Fire Marshal Program Manager June 15, 2005 DN-7000 • Al -360 NO.TI F ER® NC-100 and NC-100R Control and Relay Modules by Honeywell for the FireWarden-100 Section: Addressable GENERAL The NC-100 Addressable Control Module provides NOTIFIER's FireWarden-100 intelligent control panels a su- pervised Class B (Style Y) or Class A (Style Z) circuit for Noti- fication Appliances (horns, strobes, etc.). Addressability al- lows the NC-100 to be activated, either manually or through panel programming, on a select (zone or area of coverage) basis. The NC-bOA Addressable Relay Module provides the FireWarden-100 system with two isolated sets of Form-C dry-contact outputs for activating a variety of auxiliary de- vices, such as fans, dampers, door holders, control equip- ment, etc. Addressability allows the dry contact to be acti- vated, either manually or through panel programming, on a select basis. FEATURES Built-in type identification automatically identities these devices to the control panel. Internal circuitry and relay powered directly by two-wire SLC loop. The NC-100 module requires power (for horns, strobes, etc.). Integral LED 'blinks" green each time a communication is received from the control panel and turns on steady when activated. High noise immunity (EMF/RFt). The NC-100 may be used to switch 24-volt NAC power. Wide viewing angle of LED. SEMS screws with clamping plates for wiring ease. Direct Decade 01-99 (FireWarden-100) entry of address. APPLICATIONS The NC-100 is used to switch 24 VDC audible/visual power. The NC-100R may be programmed to operate dry contacts for door holders, Air Handling Unit shutdown, etc. CONSTRUCTION The face plate is made of off-white Noryl®. Controls include two rotary switches for direct-dial entry of address (01-99 on the FireWarden-100). The NC-100 is configured for a single Class B (Style Y) or Class A (Style Z) Notification Appliance Circuit. The NC-100R provides two Form-C dry contacts that switch together. OPERATION Each NC-100 or NC-bOA uses one of 99 (FireWarden- 100) possible module addresses on a SLC loop. It re- sponds to regular polls from the control panel and reports its type and status, including the open/normal/short sta- tLls of its Notification Appliance Circuit (NAC). The LED blinks with each poll received. On command, it activates California LState Fire MEA Marshal 7300-0028:230 LISTED S63 <( APPROVED CON iF OL NC-100 and NC-100R module its internal relay. The NC-100 supervises Class B (Style Y) or Class A (Style Z) notification or control circuits. Upon code command from the panel, the NC-100 will dis- connect the supervision and connect the external power supply in the proper polarity across the load device. The disconnection of the supervision provides a positive indi- cation to the panel that the control relay actually turned ON. The external power supply is always relay isolated from the communication loop so that a trouble condition on the external power supply will never interfere with the rest of the system. Rotary switches set a unique address for each module. The address may be set before or after mounting. The built-in TYPE CODE (not settable) will identify the module to the control panel, so as to differentiate between a mod- ule and a sensor address. Noryl® is a registered trademark of GE Plastics, a subsidiary of General Electric Company. product information up-to-date and accurate. We cannot cover all specific applications or I ISO 9001 I This document is not intended to be used for installation purposes We try to keep our I anticipate all requirements. All specifications are subject to change without notice. I For more information, contact NOTIFIER. Phone: (203)484-7161 FAX: 12031484-7118 I =1 ;b I M F!1 .] I NOT I F I E Rv NCINURINB & MANUFACTURING I by Honeywell 12 Clintonville Road, Northtord, Connecticut 06472 QUALITY SYSTEMS DN-7000 • 06/15/05 - Page 1 of 2 SPECIFICATIONS FOR NC- 700 Normal operating voltage: 15 to 32 VDC. Maximum current draw: 5.1 mA (LED on). Average operating current: 390 pA (LED flashing). External supply voltage (between Terminals T3 and T4): maximum 80 volts (IRMS or DC). Drain on external supply: 2 mA maximum (using internal EOL relay). EOL resistance: 47K ohms. Temperature range: 32°F to 120°F (0°C to 49°C). Humidity range: 10% to 93% noncondensing. Dimensions: 4.5° (11.43 cm) high x 4.0 (10.16 cm) wide x 1.25° (3.175 cm) deep. Mounts to a 4.0 (10.16 cm) square x 2.125° (5.398 cm) deep box. RELAY CONTACT RATINGS for both control and relay models Load Description Application Maximum Voltage Current Rating Resistive Non-Coded 30 VDC 3.0 A Resistive Coded 30 VDC 2.0 A Resistive Non-Coded 110 VDC 0.9 A Resistive Non-Coded 125 VAC 1 0.9 A Inductive (LJR = 5 ms) Coded 30 VDC 0.5 A Inductive ([/R = 2 ms) Coded . 30 VDC 1.0 A Inductive (PF = 0.35) Non-Coded 125 VAC 0.5 A SPECIFICATIONS FOR NC- 700R Normal operating voltage: 15 to 32 VDC. Maximum current draw: 5.1 mA (LED on). Average operating current: 270 pA (LED flashing). EOL resistance: not used. Temperature range: 32°F to 120°F (0°C to 49°C). Humidity range: 10% to 93% noncondensing. Dimensions: 4.5° (11.43 cm) high x 4.0° (10.16 cm) wide x 1.25 (3.175 cm) deep. Mounts to a 4.0 (10.16 cm) square x 2.125° (5.398 cm) deep box. PRODUCT LINE INFORMATION NC-100 Intelligent addressable control module. NC-1 OOR Intelligent addressable relay module. SMB500 Optional surface-mount backbox. CB500 Control module barrier - required by UL for separating power-limited and non-power lim- ited wiring in the same junction box as NC-100. MOUNTING DIAGRAMS Note CB500 Module Barrier, which creates isolated quadran .1 -J -( ISOLATED QUADRANT 00 Page 2 of 2 - ON-7000 • 06/15/05 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7300-0028:230 Page 1 of 1 CATEGORY: Misc. Devices/Control Unit Accessories LISTEE: Notifier, 12 Clintonville Rd, Northford CT 06472 Contact: Lawrence Flood (203) 484-1200 Fax (203) 484-7309 DESIGN: Models NMM-100P, NMM-100, and NZM-100 monitor modules; Models NC-100R and NC-1 00 control modules. Refer to listee's data sheet for additional detailed product description and operational considerations. RATING: 15-32 VDC INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating, and UL label. APPROVAL: Listed as control unit accessories for use with listee's separately listed electrically compatible fire alarm control units. Refer to listee's Installation Instruction Manual for details. XLF: 7300-0075:185 10-20-2004 This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not. be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources. Date Issued: JUNE 4, 2007 Listing Expires June 30, 2008 Authorized By: MIKE TANAKA, Senior Deputy State Fire Marshal Program Manager Series ASA udible Strobe Appliances and Series AHAudclibles r Description The Wheelock patented 2-wire Series AS Audible Strobe Appliances and Series AH Audibles offer more features with low current draw. Strobe options for wall mount models include 1575cd or the Wheelock patented MCW multi-candela wall strobes with field selectable candela settings of 15/30/75/110cd, or the high intensity MCWH strobe with field selectable 135/185cd. Ceiling mount models incorporate Wheelock's patented MCC multi-candela ceiling strobe with field selectable intensities of 1 5/30175/95cd or the high intensity MCCH strobe with field selectable 115/177cd. The audible provides a selectable choice of either a continuous horn or temporal pattern (Code 3) when constant voltage from a Fire Alarm Panel (FACP) is applied. Each tone has 3 dBA settings to choose from. When used with the Wheelock Series SM or DSM Sync Module or Wheelock PS-24-81VIC Power Supplies with Patented Sync Protocol, synchronization of the continuous horn tone provides the temporal (code 3) tone (mandated by NFPA 72) simultaneously for all audible appliances. This ensures a distinct temporal (code 3) pattern when 2 or more audibles are within hearing distance. If not synchronized the temporal sound could overlap and not be distinctive. At the same time the strobes will be synchronized. This provides the ability to comply with ADA guidelines concerning photosensitive epilepsy and the NFPA standards when installing 2 or more visual appliances within the field of view all of this plus the ability to silence the audible is achieved by using only 2 wire Features Approvals include: UL Standard 1971 UL Standard 464 New York City (MEA), California State Fire Marshal (CSFM) Factory Mutual (FM), and Chicago (BFP). See approvals by model in Specifications and Ordering Information ADNNFPA/UFC/ANSI Compliant Wall mount models are available with Field Selectable Candela Settings of 15/30/75/110cd or 135/185cd (Multi- Candela models) or 1575cd (single candela model) Ceiling mount models are available with field selectable candela settings of 15/30/75/95cd or 115/177cd (multi-candela ceiling models) Selectable Continuous Horn or Temporal (Code 3). 3 Selectable dBA settings (99, 95 and 90 dBA) in both tones Patented 2-Wire Audible Strobe Appliance. Patented Universal Mounting Plate Weatherproof models are available for outdoor use Strobes produce 1 flash per second over the regulated voltage range 12 and 24 VDC models with wide UL Regulated Voltage Range' using filtered DC or unfiltered FWR input voltage The strobes can be synchronized using Wheelock's sync modules or power supplies with built in sync protocol Fast installation with IN/OUT screw terminals using #12to#18AWG wires For 14/s atheiptoof Seie.s AS. See Dataiie S9004 © M MEA t1_I APPROVED E594r 1 ., - 2.0O5 1 AH-1 2 AS-i 21575W High (99) 12 vdc 0.163 0.260 UL max' 0192 0320 dBA Uteri f95i 12 vdc 0.076 0.195 UL max' 0.108 0.275 dBA Low (90/ ' 1 2 vdc 0.0119 0 175 UL max' 0059 0.205 Table 4: Average Current* (AMPS) For Series ASWP° Voltage High dBA Setting (99) dBA Medium dBA Setting (95) dBA Low dBA Setting (90) dBA 24.0 VDC 0,128 . 0,105 0.098 ULMax' 0.168 0155 0.150 WAS current ratings are per UL average RMS method. UL max current rating is them a ximUrn RMS current within the listed voltage,range (16-33v for 24v units). For strobes the UL max cLirrent is usually at the minimum Fisted voltage (16'.i for 24i units) For audibles the max current is usually at the maximum listed voltage (33v for 24i units). For unfiltered FVJR ratings. see installation instructions. NOTE: All CAUTIONS and WARNINGS are identified by the symbol A. All warnings are printed in bold capital letters. 4 WARNING: PLEASE READ THESE SPECIFICATIONS AND ASSOCIATED INSTALLATION INSTRUCTIONS CAREFULLY BEFORE USING, SPECIFYING OR APPLYING THIS PRODUCT, VISIT WWW.COOPERWHEELOCK.COM OR CONTACT COOPER WHEELOCK FOR THE CURRENT INSTALLATION INSTRUCTIONS. FAILURE TO COMPLY WITH ANY OF THESE INSTRUCTIONS. CAUTIONS OR WARNINGS COULD RESULT IN IMPROPER APPLICATION, INSTALLATION AN D / O R OPERATION OF THESE PRODUCTS IN AN EMERGENCY SITUATION, WHICH COULD RESULT IN PROPERTY DAMAGE, AND SERIOUS INJURY OR DEATH TO YOU AND/OR OTHERS. General Notes: Strobes are designed to flash at 1 flash per second minimum over their Regulated '10)/age Range. Note that NFPA-72 specifies a flash rate of 1 to 2 flashes per second and ADA Guidelines specify a flash rate of 1 to 3 flashes per second. All Candela ratings represent minimLim effective Strobe intensity based on UL Standard 1971. Series NS Strobe products are listed under UL Standard 1971 for indoor use with a temperature range of 32-F to 120'F )OC to 49CC) and maximum humidity 0193% .(± 2%). Series NH horns are listed under UL Standard 464 for audible signal appliances (Indoor use only). "Regulated Voltage Range" is the newest terminology used by UL to identify the voltage range. Prior to this change UL used the terminology Listed Voltage Range". Table 1: Ratings Per UL 1971 Model Number Input Voltage VDC Regulated Voltage Range VDC/FWR Strobe Candela (Cd) AS-24MCW 24 16.0-33.0 15/30/75/110 AS-24MCCH 24 16-0-33.0 115/177 AS-241575W 24 16.0-33.0 15 (75 on Axis) AS-121575W 12 8.0-17.5 15 (75 on Axis) AS-24MCC 24 16.0-33.0 15/30/75/95 AS-24MCWH 24 16.0-33.0 135/185 ASWP-2475W 24 16.0-33.0 75 @ -31°F Table 2: dBA Ratings for 12 VDC and 24 VDC Series AS/AH 12 and 24 VDC Audible ReverberaAnechoic Description Volume perdts UL 464 dBA @10 ft. @ 10 ft. High . 91 99 Continuous Medium 88 95 Horn Low 83 90 High 87 99 Medium 84 95 Code 3 Horn Low 79 90 Table 3: Average RMS Current 24 VDC Models Audible AH-24 AS-241575V0 1575cd High (99) dBA 24 vdc 0.062 0.100 UL max* 0.080 0.121 Med (95) dBA 24 vdc 0.033 0.080 UL max* 0.043 0.107 Low (90) dBA 24 vdc 0.017 0.072 UL max* 0.021 0.100 12 VDC Models Audible Wall Mount Audible Strobe Wall Mount Audible Strobe Models Ceiling MountAudible Strobe Models AS.24MCW AS-24MCWH AS-24MCC AS-24MCCH 15cd 30cd 75cd hOod 1 35c 185cd 15cd 30cd 75cd 95cd 11 5c 1 77c 0.080 0.102 0.150 0.194 0.250 0.320 0.088 0.114 0.165 0.205 0.250 0.320 0.088 0.125 0.200 0.267 0.355 0.480 0.095 0.138 0.221 0.285 0.355 0.480 0.060 0.084 0.132 0.173 0.230 0.305 0.066 0.092 0.145 0.186 0.230 0.305 0.074 0.110 0.190 0.253 0.340 0.465 0.080 0.122 0.201 0.269 0.340 0.465 0.052 0.076 0.121 0.158 0.220 0.295 0.056 0.082 0.132 0.173 0.220 0.295 0.068 0.105 0.182 1.335 0.460 0.074 0.113 0.198 0.263 0.335 0.460 Wiring Diagrams SERIES AS APPLIANCES NON-SYNCHRONIZED FROM TO NEXT PRECEDING APPLIANCE APPLIANCE - I I OR EOLR ORFACp SERIES AS & RSS APPLIANCES SYNCHRONIZED WITH PS-12/24-8CP and PS-12/24-81VIP ci,rriIi L)Li< AS AS - IP i i SERIES AS APPLIANCES SYNCHRONIZED WITH DSM MODULE CLASSA" NAC CIRCUIT WITH NO AUDIBLE SILENCE FEATURE SERIES AS APPLIANCES SYNCHRONIZED WITH SM MODULE GLE CLASS "B" NAC CIRCUIT WITH AUDIBLESILENCE FEATLI RE SERIES AS APPLIANCES SYNCHRONIZED WITH MULTIPLE DSM MODULES DSNI iii AS AS AL,cfible NAC C1 DSM t4 2 Sirobe NAC T, - Sync C Audible. N.A.0 C ft DSM 4±3 Svrr Strobe NAC Ci m + Interconnecting wiring shown. Maximum of twenty (20) For detail using SM or DSM Sync Module refer to Data Sheet S3000 or Installation Instructions P83123 for SM and P83177 for DSM. For wiring informationon the power supplies refer to Installation Instructions P84662 for PS-24-8MC. Specifications and Ordering Information Model Number Order Code Strobe Candela Sync Sync /ISrM ii o PS248MC 24 VDC 12 VDC Wall Mount Ceiling Mount AgencyApprovals UL MEA CSFM FM BFP AS-24MCW-FR 9024 15/30/75/110 X X X - X - A.BD,E.F.G.H,JN,O,R,X X X X x x AS-24MCW-FW 9025 15/30/75/110 X X X - X - A,B,D,EF.G.H,J,N,O,R,X X X X x x AS-24MCWH-FR 3468 135/185 X X X - X - A,B,D.E,F,G,H,J,N,OR,X X X X x AS-24MCWH-FVV 3469 135/185 X X X - X - AB.D.EF,G.H,J.,N,OR,X X X X x AS-241575W-FR 7405 15 (75 on Axis) X X X - - ABDE.F.G.H,J.NO.R.X X X X x x A5121575WFR 7410 15 (75 on Axis) X X - X X - A,B,D,E.FG:H:J.N,O,R,X X X X X X AS-24MCC-FR 3161 15/30/75/95 X X X - X ABD.E,FG.HJ,NO,R,X X X X x AS-24MCC-FW 3162 15/30/75/95 X X X - - X AB.D,E,F.G.H.J,N,OX X X 7 AS-24MCCH-FW 3467 115/177 X X X- - A.B.D.E.FG.H.J1'tO.R.X X X 7 AS'°IP-2475\N-FR 9012 75 -31 `F X X X - X - I (see Data Sheet S9004) X X x X AH-24-R 7892 X X X - X X AB.D.E_FG,HJ.N.O.R,X X X X AH-24-VV 7893 - X A X - X X A8.D.E.EG.H.J.N.O.R.X A X 7 X A AH-12-R 7891 - X A . - X X X A.B.D_E.F.G.H.J.N,O,R.X A X 7 x x AH-12-VJ 7894 X - XX A AB.D.E.F.CHJN.OR,XX X 7 x x AH-24WP-R. AH2NP-R 7416 7415 - A X A A - AH Ix x x x x K x i1 x For Weatherproof Series AS//'.H specifications see data sheet S9004. PENDING "Refer to Data Sheet S7000 for Mounting Options. Note Models are available in either Red or V/bite. Contact Customer Service for Order Code and Delivery. NOTE: Due to continuous development of our products, specifications and offerings are subject to change without oti' -e in accordance with Wheelock Inc. standard terms and conditions. Architects and Engineers Specifications The notification appliances shall be Wheelock Series AS Audible Strobe appliances and Series AH Audible appliances or approved equals. The SeriesAS Audible be listed for UL Standard 1971 (Emergency Devices for the Hearing-Impaired) for Indoor Fire Protection Service, The Series AH Audible shall be UL Listed under Standard 464 (Fire Protective Signaling). Both shall meet the requirements of FCC Part 15 Class B. All inputs shall be compatible with standard reverse polarity supervision of circuit wiring by a Fire Alarm Control Panel (FACP). The audible portion of the appliance shall have a minimum of three (3) field selectable settings for dBA levels and shall have a choice of continuous or temporal (Code 3) audible outputs. The strobe portion of the appliance shall produce a flash rate of one (1) flash per second over the Regulated Voltage Range and shall incorporate a Xenon flashtube enclosed in a rugged Lexan® lens. The Series AS shall be of low current design. Where Multi- Candela appliances are specified, the strobe intensity shall have field selectable settings and shall be rated per UL Standard 1971 at 15/30/75/110 or 135/185 candela for wall mount and 15/30/75/95 or 115/177 candela for ceiling mount. The selector switch for selecting the candela shall be tamper resistant. The 1575 candela strobe shall be specified when 15 candela UL Standard 1971 Listing with 75 candela on-axis is required (e.g. ADA compliance). When synchronization is required the appliance shall be compatible with Wheelocks SM, DSM Sync Modules or Wheelock PS-24-8MC Power Supplies with built-in Patented Sync Protocol. The strobes shall not drift out of synchronization at any time during operation. If the sync module or Power Supply fails to operate, (i.e., contacts remain closed), the strobe shall revert to a non-synchronized flash- rate. The appliance shall also be designed so that the audible signal may be silenced while maintaining strobe activation when used with Wheelock synchronization. The Series AS Audible Strobe and Series AH Audible shall incorporate a Patented Universal Mounting Plate that shall allow mounting to a single-gang, double-gang, 4-inch square, 100mm European type backboxes or the SHBB Surface Backbox. If required, an NATP (Notification Appliance Trimplate) shall be provided. All notification appliances shall be backward compatible. 273 Branchport Avenue Long Branch, NJ 07740 Phone: (800) 631-2148 Fax: (732) 222-2588 www.cooperwheelock. cam WE ENCOURAGE AND SUPPORT NICET CERTIFICATION 3 YEAR WARRANTY Made in USA S8100 AS/AH 06106 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7125-0785:131 Page 1 of 2 CATEGORY: Fire Alarm Devices for the Hearing-Impaired LISTEE: Wheelock Inc., 273 Branchport Ave. Long Branch NJ 07740 Contact: Luy Nguyen (732) 433-6005 Fax (732) 222-5607 DESIGN: Models AS-1215, -2415, -1230, -2430, -121575, -241575, -2475 and -24110 audible/strobes fcr the hearing impaired followed by any three alpha/numeric characters indicating lens orientation, lettering and color. Models AS-1215W, -2415W, -1230W, -2430W, -121575W, -241575W, -2475W and -24110W audible/strobes for the hearing impaired followed by any three alpha/numeric characters indicating lens orientation, lettering and color. These units with suffix -W are for wall mount only. Models AS-24150, -24300, -24750 and -241000 audible/strobes for the hearing impaired followed by two alpha/numeric characters indicating lens lettering, orientation and color. These units are intended for ceiling mount only. Model AH-12, -24, AH-12WP, -24WP audible appliances (no strobe), followed by an alpha or numeric character indicating product color. Model AS-24M0W and AS-24MCC audible/strobe, followed by any two alpha or numeric character indicating lettering and product color. Model ASWP-2475W audible/strobe with integral private mode fire/emergency visual signaling for non-hearing impaired applications. Model ASWP-2475W is also suitable for outdoor use when mounted to Model WPBB back box. Models AS-24MCWH and AS-24MCCH audible/strobes for the hearing impaired followed by two alpha/numeric characters indicating lens lettering and product color. Units with suffix C are for ceiling mount only. Units with suffix W are for wall mount only. Refer to the listee's data sheet for detailed product description and operational considerations RATING: Electrical: 8-17.5/16-33 VDC/VFR Candela: 15:15cd, 1575:15/75cd, 30:30cd, 75:75cd, 95:95cd, 100:100cd, 110:110cd MOW: Selectable 15cd, 30cd, 75cd, 110cd MOO: Selectable 15cd, 30cd. 75cd, 95cd MCWH: Selectable 135cd. 185cd MCCH: Selectable 115cd, 177cd INSTALLATION: In accordance with istee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. Models ASWP-2475V'! and AS-__ are for wall mount only. Models with suffix -W are for wall mount only. Models with suffix -C are for ceiling mount only. *Rev. 06-13-06 Listing No. 7125-0785:131 Page 2 of 2 MARKING: Listees name, model number, electrical/candela rating, and UL label. APPROVAL: Listed as audible and audible/visual signaling devices suitable for the hearing impaired when Used in conjunction with separately listed electrically compatible fire alarm control units. For indoor Use only except Models AH-i 2WP and AH-24WP audible appliances are suitable for indoor/outdoor. For synchronization Models AS Series must be used with Model SM-i 2/24, SMX-i 2/24, DSM._ 12/24 or DSMX-12/24 sync control module (CSFM Listing No. 7300-0785:132). Refer to listee'5 Installation Instruction Manual for details. These appliances can generate a distinctive three-pulse Temporal Pattern Fire Alarm Evacuation Signal (for total evacuation) in accordance with NFPA 72, 2002 Edition. NOTE: Models ASWP-2475W, AH-12, AH-24, -12WP and -24WP audible devices are not suitable for the hearing impaired applications. Rev 06-13-06 This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the tesiresLiIts and/or other data but does not make an independent verification of any claims This listing is. not an endorsement or 3fg< recommendation of the item listed This listing should not be used to verily correct operational requirements or inslallation criteria Refer to listees data sheet. installation instructions and/or other suitable information sources. Date Issued: JUNE 4, 2007 L/sti'ngExpires June 30, 2008 Authorized By: MIKE TANAKA. Senior Deputy State Fire Marshal Program Manager