HomeMy WebLinkAbout965 PALOMAR AIRPORT RD; ; FS130027; Permit12/27/24,12:37 PM FS130027 Permit Data
City of Carlsbad
Fixed Systems Permit
Permit No: FS130027
965 PALOMAR
Job Address: Status: APPROVED
AIRPORT RD
Permit Type: FIXSYS Applied 10/7/2013
Parcel No: 2110403400 Approved: 10/28/2013
Lot #: 0
Reference No.: Issued: 10/28/2013
PC #: Inspector:
Project Title: VEGGIE.GRILL NEW KITCHEN HOOD FIRE SYSTEM. NEW
HOOD. NEW TENANT. (2) PLENUM (2) DUCT (2) FRYERS 14: X
14" POT (2) RANGES 36" (2) BROILERS (1) GRIDDLE (1) RANGE
12" X 24"
Applicant:
AZTEC FIRE & SAFETY
8107 COMMERCIAL ST
LA MESA, CA
619-464-5625
Owner:
OSCARS CARLSBAD L L C
1959 PALOMAR OAKS WAY #300
CARLSBAD CA
Fees ($) Add'I Fees ($) Total ($) Balance ($)
333 0 333 0
about:blank 1/1
at the center of the cross section 01 the duct.
NOTE: In no case shall the diagonal
dimension of the duct exceed 18.8 inches
without additional duct nozzles.
OF VERTICAL DUCT
- - OF HORIZONTAL DUCT
/ AIM POINT
VERTICAL / HORIZONTAL DUCT
TRANSITIONS
Special Note: For ducts with vertical/horizontal
transitions reference the diagram above with respect
to nozzle aim.
TRANSITION LIMITATIONS - SINGLE NOZZLE (P/N 16416)
A transition is a section found on some exhaust systems between the hood and the duct. One Amerex
duct nozzle (P/N 16416) will protect a transition at the point where the transition is 50 perimeter inches
(127 cm) or less or a diameter of 16 inches (40.6 cm) or less. The nozzle has one flow point and must be
placed in the center of the opening at the point where the perimeter inches are 50 (127 cm) or less, or
where the diameter inches are 16 (40.6 cm) or less and aimed at the center of the cross section on the
duct. Additional duct protection is not required when using this method.
/
DUCT PROTECTION LIMITATIONS -
TWO NOZZLES (2 x P/N 16416)
Two Amerex duct nozzles (PIN 16416) will protect ducts with
51 inches to 82 inches (129.5 - 208.3 cm) or a maximum d
inches (66 cm). To correctly position the nozzles a rectangul
be divided along its longest side into four equal distances.
should be divided along a centerline into four equal distance
should be placed at one quarter of the duct's width (or diamE
nozzles on the centerline, paced 2-8 inches (5.08 - 20.3 cm)
opening and aimed at the center of the cross section of th
nozzle has one flow point.
NOTE: In no case can the diagonal dimension of
each module exceed 18.8 inches (46 cm).
DUCT PROTECTION LIMITATIONS 100 IN. PERIMETER
TWO _lh/2 FLOW POINT NOZZLES (PIN 11983)
The Amerex solid fuel appliance/duct nozzle (P/N 11983) is listed to
protect a restaurant cooking exhaust duct of unlimited length and up
to 100 perimeter inches (254 cm) or 32 inch diameter (81.2 cm)
using two nozzles. The nozzles total three flow points and to
properly position the nozzles, a rectangular duct should be divided
along its longest side into four equal distances. A circular duct
should be divided along its center line into four equal distances. The
nozzles are to be placed at one quarter and three quarters position
of the duct width (or diameter) with both nozzles on the center line,
placed 2 - 8 inches (5.08 - 20.3 cm) into the duct opening and aimed
straight up in a vertically run duct.
NOTE: In no case can the diagonal dimension of
the duct exceed 37.2 inches (94.4 cm)
without adding additional duct nozzles.
NOTE: The use of one duct nozzle PIN 11983 is
permitted for duct 50 perimeter inches or
less in the same manner as duct nozzle
16416.
32' MAX
NOTE: In no case shall the diagonal
dimension of the duct exceed 18.8 inches
without additional duct nozzles.
OF VERTICAL DUCT
- - - OF HORIZONTAL DUCT
AIM POINT
VERTICAL / HORIZONTAL DUCT
TRANSITIONS
Special Note: For ducts with vertical/horizontal
transitions reference the diagram above with respect
to nozzle aim.
TRANSITION LIMITATIONS -SINGLE NOZZLE (P/N 16416)
A transition is a section found on some exhaust systems between the hood and the duct. One Amerex
duct nozzle (P/N 16416) will protect a transition at the point where the transition is 50 pe,rimeter inches
(127 cm) or less or a diameter of 16 inches (40.6 cm) or less. The nozzle has one flow point and must be
placed in the center of the opening at the point where the perimeter inches are 50 (127 cm) or less or
where the diameter inches are 16 (40.6 cm) or less and aimed at the center of the crosssection on the
duct. Additional duct protection is not required when using this method.
DUCT PROTECTION LIMITATIONS -
TWO NOZZLES (2 x P/N 16416)
Two Amerex duct nozzles (P/N 1 641 6) will protect ducts with
51 inches to. 82 inches (129.5 - 208.3 cm) or a maximum d
inches (66 cm). To correctly position the nozzles a rectangul
be divided along its longest side into four equal distances. /
should be divided along a centerline into four equal distance
should be placed at one quarter of the duct's width (or diamE
nozzles on the centerline, paced 2-8 inches (5.08 - 20.3 cm)
opening and aimed at the center of the cross section of thE
nozzle has one flow point.
NOTE: In no case can the diagonal dimension of
each module exceed 18.8 inches (46 cm).
DUCT PROTECTION LIMITATIONS 100 IN. PERIMETER
TWO - 11/2 FLOW POINT NOZZLES (P/N 11983)
The Amerex solid fuel appliance/duct nozzle (P/N 11983) is listed to
protect a restaurant cooking exhaust duct of unlimited length and up
to 100 perimeter inches (254 cm) or 32 inch diameter (81.2 cm)
using two nozzles. The nozzles total three flow points and to
properly position the nozzles, a rectangular duct should be divided
along its longest side into four equal distances. A circular duct
should be divided along its center line into four equal distances. The
nozzles are to be placed at one quarter and three quarters position
of the duct width (or diameter) with both nozzles on the center line,
placed 2 - 8 inches (5.08 - 20.3 cm) into the duct opening and aimed
straight up in a vertically run duct.
NOTE: In no case can the diagonal dimension of
the duct exceed 37.2 inches (94.4 cm)
without adding additional duct nozzles.
NOTE: The use of one duct nozzle P/N 11983 is
permitted for duct 50 perimeter inches or
less in the, same manner as duct nozzle
16416.
32" MAX