The URL can be used to link to this page

Home My WebLink About3284 GREY HAWK CT; ; AS080165; Permit11/7/24, 4:10 PM AS080165 Permit Data City of Carlsbad Sprinkler Permit 3284 GREY HAWK Job Address: CT Permit Type: SPRINK Parcel No: 2210150727 Lot #: 0 Permit No: AS080165 Status: ISSUED Applied 10/14/2008 Approved: 10/15/2008 Reference No.: Issued: 10/15/2008 PC #: Inspector: Project Title: NEVELL GROUP (NGI) TI FIRE SPRINKLER PLAN CHECK & INSPECTIONS Applicant: SPRINKMATIC, A CORPORATION SUITE 245 79 DAILY DR CAMARILLO, CA 805-640-9676 Owner: B M I HOLDINGS LTD PARTNERSHIP 3001 ENTERPRISE ST #200 BREACA [ Fees ($) I Add'I Fees ($) Total ($) Balance L130 0 130 0 about:blank 1/1 Sprinkmatic 79 Daily Drive #245, Camarillo, CA 93010 Ph. (805) 640-9676 Fax (805) 640-9682 License# 690171 / C-16 Material Cut sheet Submittal for: NGI 3284 Greyhawk Court Carlsbad, CA Date: 10-13-08 By:C.H. DynamThread 0 Full Line Sch-40 Replacement Dyna-Thread offers the life expectancy of Sch40 with superior hydraulics and greater value. Dyna-Thread sprinkler pipe represents an engineering advancement for the sprinkler pipe industry. It combines the safety and longevity of traditional Sch-40 pipe with quality and superior hydraulic advantages. Dyna-Thread's inside diameter is up to 3.6% larger than Sch40 giving it superior hydraulics. And, when used in combination with Dyna-Flow pipe, down sizing often occurs. Dyna-Thread is fully listed and approved by UL, ULC, and FM for fire sprinkler applications. The life expectancy of Dyna-Thread and Sch-40 are equal based on the calculated wall thicknesses per UL. The consistent quality of steel used to make Dyna-Thread facilitates smooth threading and lower maintenance costs. The exterior of Dyna-Thread is protected by a clean, durable mill coating for extended shelf life and easy paint application. @ <~> 9 Listed Approved Listed With its increased strength and lighter weight, Dyna-Thread reduces installation fatigue and is ideal for retro-fit applications. Corrosion Resistance Ratio (CRR) is a UL (Underwriters Laboratory) term for the estimated life expectancy of a pipe joint. This is based on the calculated wall thickness at the base of the first exposed thread, assumed to be the weakest point of the pipe length. Dyna- Thread and Sch-40 have the same calculated wall thicknesses at this point and are both assigned the same CRR of 1.00. The internal surface of all black Allied Tube & Conduit Fire Sprinkler pipe products up to 4.5000" in diameter is coated with our new Antibacterial Formula, "ABF". In scientific laboratory test, ABS proved to have superior resistance to microbial colonization of pipe walls, thereby delaying or possibly preventing the onset of Microbiologically Influenced corrosion (MIC) when the First Sprinkler System is first installed. More wall thickness at the thread (CRR= 1.00) gives Dyna-Thread better life expectancy than lightwall threadable pipe joints. Unlike lightwall threadable pipe, Dyna-Thread has no thread gauge warning. Dyna-Thread is approved for standard hanger spacing (15 ft. O.C.), can be used as earthquake sway bracing, and is safe to use as drops. Dyna-Thread is safer to weld on. Dyna-Thread is more widely accepted than lightwall threadable where Sch-40 is specified. Super 40/Dyna-Thread pipe is manufactured to meet: ASTM A- 135, Grade A and is in compliance with NFPA- 13. All sizes of Super 40/Dyna- Thread are rated at 300 psi working pressure. Super 40/Dyna-Thread is UL and ULC Listed for wet, dry deluge and pre-action sprinkler systems and FM Approved for use in wet systems. Super 40/Dyna-Thread can be "hot-dip" galvanized to meet FM requirement for dry systems. Super 40iDyna-Thread is approved for all threaded couplings and welded outlets and is suitable for all roll-grooved, and plain-end fittings. (See listing information). Specifications NPS Nominal I.D. Wt. WI. (H20 Filled) Pcs/ WI/lilt (21') WI/Lift (24') WI/lift (25') In; mm In; mm Lbs/Ft; Kg/rn Lbs/Ft; Kg/rn Lift Lbs; Kg Lbs; Kg Lbs; Kg ill 1.080 1.330 1.75 70 1955 2234 232 25 27.4 2.0 2.60 70 887 1013 105 11/4 1.408 1.870 2.54 51 2002 2288 2384 32 35.8 2.8 3.78 51 908 1038 108 lh/2 1.639 2.290 3.22 44 2115 2418 2519 40 41.6 3.4 4.79 44 959 1097 114 2' 2.104 3.050 4.57 30 1921 2196 228 50 53.4 4.5 6.80 30 871 996 103 tqcu/Flow control (") llied 16100 S. Lathrop• Harvey, IL 60426 Customer Service: 11350 Norcom Rd. • Philadelphia, PA 19154 (800) 882-5543 TUBE &CONDUIT 2525 N. 27th Ave. Phoenix, AZ 85009 Fax 708-339-1806 S3-3 <@> SMITH COOPER INTERNATIONAL <@> Ductile Iron Threaded Fittings * ALL FITTINGS 100% AIR TESTED *ASME/ ANSI B16.3 C () US * ISO 9001:2000 MANUFACTURER * ASTM A536 Grade 65,45,12 LISTED * LISTED/APPROVED AT 500 PSI * ASME /ANSI B 1.20.1 APPROVED Ductile Iron 90° Elbow Figure 35E Size I - A Wgt -' T 1/2 1.13 0.24 1 1 1.50 0.64 1-1/4 1.75 0.95 1-1/2 1.94 1.24 2 2.25 1.74 2-1/2 2.70 3.28 Ductile Iron Re1uicin 90° Elbow Figure 35RE Size A B Wgt -A--' 3/4x1/2 1.22 1.20 0.33 1x1/2 1.36 1.26 0.44 1 x3/4 1.45 1.38 0.53 1-1/4x1/2 1.53 1.34 0.64 1-1/4x3/4 1.63 1.45 0.75 1-1/4x1 1.67 1.58 0.77 1-1/2 x 1/2 1.75 i 1-1/2 x 3/4 115 1.52 0.95 1-1/2x1 1.80 1.65 0.99 1-1/2x1-1/4 1.88 1.82 1.14 2x1/2 1.97 1.60 1.35 2x3/4 1.97 1.60 1.39 2 x 1 2.02 1.73 1.58 2x1-1/4 2.10 1.90 1.62 2x1-112 2.16 2.02 1.67 2-1/2 x 1-1/2 2.51 2.16 2.32 2-1/2x2 2.60 2.39 3.01 Ductile Iron Rricc Seit union Figure 35U Size X Wgt 1/2 1.88 -:-47 fl hA1 I d 1-1/4 2191.08 [ T 2.50 1.54 1-1/2 1 2.62 Tö 2 1 3.121 3151 Ductile Iron Tee Figure 35T !T T Wgt I I T T I I J L 1/2 1.13 0.33 3/4 11-1/4 1.31 0.50 A I A 1 1.50 0.85 115 1.30 1-1/2 1.94 1.63 12-1/2 2.70 4.55 Ductile Iron Cniinlincr Figure 35CP Size A jfj A 1 1/2 1.38 0.18 3/4 1.63 0.26 1 1.75 0.44 1-1/4 2.00 0.54 1-1/2 1 2 5 2-1/2 L2,.6 N.1 9 Ductile Iron Can Figure 35C Size A JWgt nn 4 A 1/2 0.87 0.15 3/4 0.97 0.22 1 1.16 0.33 1-1/4 1.28 0.54 1-1/2 1.33 0.68 2 1.45 0.96 2-1/2 1.70 1.80 Ductile Iron Hex Bushing Figure 35HB Size : I I 1 1x1/2 1.06 0.22 x3/4 1.06 0.18 1-1/4x1 1.19 0.31 1-1/2x1 1.25 0.53 1-1/2x1-1/4 125 0.35 2 x 1 1.38 0.75 2x1-1/4 1.38 0.69 2x1-1/2 1 1.381 032 Ductile Iron 45° Elbow Figure 35F Size X WT F \1 1/2 0.88 0.22 3/4 098 033 1 1.13 0.48 1-1/4 1.29 013 1-1/2 1.44 0.93 2 1691.55 2-1/2 I 1.95 2.70 Ductile Iron Beam Clamus Figure 355P - Size A Wgt 318 0.75 1 0.31 1/2 0.75 1 0.54 SMITH,. COOPER <@> INTERNATIONAL <@> Ductile Iron Threaded Fittings C ® us * ALL FITTINGS 100% AIR TESTED * ASME/ ANSI B16.3 * ISO 9001:2000 MANUFACTURER * ASTM A536 Grade 65,45,12 LISTED * LISTED/APPROVED AT 500 PSI * ASME/ ANSI B 1.20.1 APPROVED Ductile Iron Bull Head Tee Figure 35BT H Ht Size A B C Wgt 314x3/4x1 1.45 1.45 1.37 0.68 1 x x 1-1/4 1.67 1.67 1.58 0.97 1x1x1-112 1.80 1.80 1.65 1.14 1-1/4x1x1-1/2 1.88 1.80 1.82 1.43 i-1/4x1-1/4x1-1/2 1.88 1.88 1.82 1.52 1-1/4x1-1/4x2 2.10 2.10 1.90 2.00 1-112x1-1/4x2 2.16 2.10 2.02 1.94 1-1/2x1-1/2x2 2.16 2.16 2.02 2.00 2x2x2-112 2.60 2.60 2.39 3.67 Ductile Iron Hex Reducing Counling Figure 35RC Size A WT ¶ 1 A 1 xl/2 1.69 0.40 1 x3/4 1.69 0.38 1-1/4x3/4 2.06 0.53 2x1(not hex) 2.81 0.53 Ductile Iron Cross & Reducing Cross Figure 35X Size A - B - Wgt -A--A- £ 1 1.50 1.50 0.97 1-1/4 1.75 1.75 1.59 1-1/2 1.94 1.94 1.89 2 2.25 2.25 2.93 Fig 51X - - Size 1-1/4x1 1.67 1.58 1.25 1-1/2x1 1.80 1.65 1.48 2x1 2.02 1.73 2.64 Ductile Iron Plugs Figure 355P Size : I A 4' 1/2 0.94 0.10 1 1.25 0.28 1-1/4 1.37 0.50 1-1/2 1.441 0.70 2 1.501 0.90 Ductile iron Reducing Tee Figure 5RT Size A 3/4x3/4x1/2 1.20 1.20 1.22 0.46 1 x 1/2 x 1 1.50 1.36 1.50 0.70 1x3/4x3/4 1.38 1.31 1.45 0.68 1 x3/4x1 1.50 1.45 1.50 0.77 1x1x1/2 1.26 1.26 1.36 0.66 lxi x3/4 1.38 1.38 1.45 0.73 1-1/4x1/2x1-i/4 1.75 1.53 1.75 1.04 1-1/4x3/4x1-1/4 115 1.62 1.75 1.09 1-1/4x1x1/2 1.34 1.26 1.53 0.81 1-1/4x1x3/4 1.45 1.38 1.63 0.90 1-1/4x1x1 1.58 1.50 1.69 1.03 1-1/4x1x1-1/4 115 1.69 1.75 1.10 1-1/4x1-1/4x1/2 1.34 1.34 1.53 0.87 1-1/4x 1-1/4x3/4 1.45 1.45 1.62 0.96 1-1/4x1-1/4x1 1.58 1.58 1.67 1.10 1-1/2x1/2x1-1/4 1.81 1.56 1.88 1.37 1-1/2x1/2x1-1/2 1.94 1.66 1.94 1.42 i-1/2x3/4x1-1/4 1.94 1.66 1.88 1.42 1-1/2x3/4x1-1/2 1.94 1.75 1.94 1.47 1-1/2x1x1/2 1.44 1.25 1.69 0.97 1-1/2x1x3/4 1.50 1.44 1.75 1.14 1-1/2x1x1 1.65 1.50 1.80 1.14 1-1/2x1x1-1/4 1.82 1.67 1.88 1.47 1-1/2x1x1-1/2 1.94 15 1.94 1.52 i-1/2x1-1/4x1/2 1.41 1.34 1.66 1.03 i-1/2x1-1/4x3/4 1.52 1.45 1.75 1.10 1-1/2 x 1-1/4 x 1 1.65 1.58 1.80 1.31 1-1/2x1-1/4x1-1/4 1.82 1.75 1.88 1.52 i-1/2x1-1/4x1-i/2 1.94 1.88 1.94 1.50 1-1/2x1-1/2x1/2 1.41 1.41 1.66 1.14 1-1/2x1-1/2x3/4 1.52 1.52 1.75 173- 1-1/2 x 1-1/2 x 1 1.65 1.65 1.80 1.38 1-1/2x1-1/2x1-1/4 1.82 1.82 1.88 1.50 2 x 1 x 2 2.25 2.02 2.25 2.18 2x1-1/4x2 2.25 2.10 2.25 2.31 2x1-1/2x1/2 1.49 1.41 1.88 1.50 2x1-1/2x3/4 1.60 1.52 1.97 1.61 2x1-1/2x1 1.73 1.65 2.02 1.65 2x1-1/2x1-1/4 1.90 1.82 2.10 2.03 2x1-1/2x1-1/2 2.02 1.94 2.16 2.37 2x1-1/2x2 2.25 2.16 2.25 2.53 2x2x1/2 1.49 1.49 1.88 1.50 2x2x3/4 1.60 1.60 1.97 1.67 2 x 2 x 1 1.73 1.73 2.02 1.91 2x2x1-1/4 1.90 1.90 2.10 2.05 2x2x1-1/2 2.02 1 2.02 2.16 2.11 Threaded Mechanical Branch Tee Model MT-30 mechanical tee serves the same function as MT-1 & MT-8 but uses a steel electro-plated U-Bolt to save space and for easier installation in tight places. It is ideal for direct connections with sprinkler heads and drop nipples. iiii..Btar Fire Products Division of Anvil' International Submittal Sheet APPROVED For Listing / Approval details contact your AnvilStar°°' Representative. I AWARNING For dry pipe systems and freezer applications lubrication of the gasket is required, Gruvlok® XtremeTM Lubricant is recommended. HOUSING: Ductile Iron conforming to ASTM A-536, Grade 65-45-12. U-BOLT & NUTS: U-bolt is carbon steel SAE Grade 2, Zinc Plated with plated hex nuts carbon steel ASTM A-i 94, Zinc Plated. THREADS: MT-30 NPT per ANSI/ASME B1.20 1 COATINGS: Zinc Electroplated J Other (Specify): Example: RAL3000 or RAL9000 Series For other Coating requirements con'ad an AnvilStar Representative. GASKETS: Materials Properties as designated in accordance with ASTM D-2000. Grade "E" EPDM (Green color code) -40°F to 230°F (Service Temperature Range) (-40°C to 110°C) Recommended for water service, diluted acids, alkalies solutions, salts, oil-Free air and many chemical services not involving hydrocarbons, oils or gases. NOT FOR USE WITH HYDROCARBONS. Other PROJECT lIINFORMATION: APPROVAL STAMP: l Project: Date: Phone: Architect / Engineer: Contractor: Address: Notes 1: Notes 2: PAGE 1 OF 2 SPF Couplings, Fittings, Flanges, Clamps For the latest UL/ULC Listed and FM Approved pressure ratings, versus pipe schedule, REV. 03.03.06-0033 go to www.anvilstar.com or contact your local AnvilStar representative Aiii..Star Threaded Mechanical Branch Tee Fire Products Division of Anvil International Submittal Sheet k'AIcIi MECHANICAL TEES Nominal Hole Diameter Max. Wk. Dimensions Approx. Max. A B C I Size Mm. O.D. Pressure WI. En. Diameter Diameter Take-Out ___ In/Dtit(mm) In/mm In/mm In/mm PSI/bar In/mm In/mm In/mm n. mm Lbs/kg 11/4 x ½ 1.660x0.840 13/ 16 300 2½ 31h 21/4 15/8 0.8 32x /2 42.4x2/.3 30 33 20.7 54 89 51.2 42 0.4 /1/4 ( 1.660x1.050 13A6 1/16 300 2½ 31h 21/4 iit 0.8 32x 19 42.4x26.7 30 33 20.7 54 89 57,2 42 0.4 /1/4 X 1 1.660x1.315 13/ 1/it 300 21/4 31/2 2/4 15/8 1.1 32x25 42.4x33.7 30 33 20.1 58 89 57.2 4/ 0.5 /2 1.900 x 0.840 /3/ 1/it 300 2/4 3/2 21/4 13/4 0.8 40x 12 48.3x21.3 30 33 20.7 5/ 89 51.2 48 0.4 11/2 x 3/4 1.900 x 1.050 1/16 1/16 300 21/4 31 21/4 1/4 0.9 40 19 48.3x26.1 30 33 20.7 57 89 57.2 48 0.4 11/2 X 1 1.900x1.315 ]3// 1/16 300 23/t 31/2 21/4 /3/4 1.1 40x25 48.3x33.7 30 33 20.7 61 89 57.2 44 0.5 2 x ½ 2.375 nO.840 13A6 1/16 300 21/2 33/4 2¼ 2 0.9 50 72 60.3x21.3 30 33 20.7 64 95 51.2 5/ 0.4 2 X 3/4 2.375x1.050 13A6 1/1 300 21/2 33/ 21/4 2 0.9 50x /9 60.3x26.7 30 33 20.7 64 95 57.2 51 0.4 2 x 1 2.375x 1.315 1/16 1/it 300 2/ 33/4 2/4 2 1.1 50x25 60.3x33.7 30 33 20.1 6/ 95 57.2 50 0.5 21/2 5 I/ 2.815x0.840 13A6 1/16 300 23/4 41/4 21/4 21/4 0.9 65x12 73.0x21.3 30 33 20.7 70 108 51.2 57 0.4 21/2 5 3/4 2.875 x 1.050 13A6 1/16 300 2/4 41/4 21/4 21/4 0.9 65x /9 13.0x26.7 30 33 20.7 10 108 1 51.2 5/ 0.4 21/2 5 1 2.815 x 1.315 ]3// 1116 300 21/8 41/4 21/4 21/4 1.1 65x25 73.0x33.7 1 30 33 20.7 1 73 1 108 57.2 1 56 1 0.5 BSP equivalent is available as a MT-90. NOTE: Tighten nuts alternatively to a recommended torque of 18-22 ft-lbs (25-30 N-m) on pipe wall less than schedule 10 or 23-27 ft-lbs (31 - 37 N-m) on pipe walls schedule 10 and above. PAGE 2 OF 2 SPF Couplings, Fittings, Flanges, Clamps For the latest UL/ULC Listed and FM Approved pressure ratings, versus pipe schedule, REV. 03.03.06-0034 go to www.anvilstar.com or contact your local Any//Star representative (1111117) JWWIL Mechanical-I® STYLES 920 AND 920N Victaulic MechanicalT® Outlet provides a direct branch connection at any location a hole can be cut in pipe. The hole is cut oversize to receive a 'holefinder" locating collar which secures the outlet in position permanently. A pressure responsive gasket seals on the pipe O.D. Cross-type connections can be achieved by utilizing two upper housings of the same style and size, with the same or differing branch size connections. NOTE: Style 920 and Style 920N housings cannot be mated to each other to achieve a cross connection. Style 920 and Style 920N Mechanical-T outlets are available with grooved or female threaded outlet. Specify choice on order. Units are supplied painted with plated bolts. Galvanized hous- ings are available, supplied with plated bolts. All sizes of Style 920 and 920N are rated at 500 psi/345OkPa working pressure on Schedule 10 and 40 carbon steel pipe. They may also be used on high density polyethylene or poly- butylene (HDPE) pipe. Pressure ratings on HDPE are dependent on the pipe rating. Contact Victaulic for ratings on other pipe. Style 920 and 920N are not recommended for use on PVC plastic pipe. Standard piping practices dictate that the Mechanical-T Styles 920 and 920N must be installed so that the main and branch connections are a true 90° angle when permanently attached to the pipeline surface. Additionally, the Vic-Tap Il® hole cutting tool, which allows for hole cutting capabilities on pressurized systems, utilizes the Style 920 Mechanical-T in conjunction with the Series 726 Vic-Ball Valve to create the Style 931 Vic-Tap II Mechanical-T unit. See page 8 for further information. 0 STYLE 920 CROSS PATENTED STYLES 920 AND 920N MATERIAL SPECIFICATIONS Housing/Coating: Ductile iron conforming to ASTM A-536, grade 65-45-12, with orange enamel coating. Ductile iron conforming to ASTM A-395, grade 65-45-15, is available upon special request. Optional: Hot dipped galvanized Gasket: (Specify choice*) Grade "E" EPDM EPDM (Green color code). Temperature range —30°F to +230°F/-34°C to +110°C. Recommended for cold and hot water service within the specified temperature range plus a variety of dilute acids, oil-free air and many chemical services. UL Classified in accordance with ANSI/NSF 61 for cold +86°F/+30°C and hot +180°F/+82°C. NOT RECOMMENDED FOR PETROLEUM SERVICES. Grade "T" nitrile Nitrile (Orange color code). Temperature range —20°F to +180°F/-29°C to +82°C. Recommended for petroleum products, air with oil vapors, vegetable and mineral oils within the specified temperature range. Not recommended for hot water services over +150°F/+66°C or for hot dry air over +140°F/+60°C. *Services listed are General Service Recommendations only. It should be noted that there are services for which these gaskets are not recommended. Reference should always be made to the latest Victaulic Gasket Selection Guide for specific gasket service recommendations and for a listing of services which are not recommended. Bolts/Nuts: Heat-treated plated carbon steel, trackhead meeting the physical and chemical requirements of ASTM A-449 and physical requirements of ASTM A-183. JOB/OWNER CONTRACTOR ENGINEER System No. Submitted By Spec Sect Para__________ Location Approved Date____________________________________ www.victaulic.com - vicTAuLic IS REGISTERED TRADEMARK OF VICTAUUC COMPANY. © 2007 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA. iCt9UIi ice REV_J 11.02_i FEMALE THREADED OUTLET Provides a direct branch connection at any location where a hole can be cut in the pipe A pressure responsive gasket provides the seal Request Publication 11.03 for Mechanical-I cross assemblies Pressure rated up to 500 psi/3450kPa on steel pipe; also available for use with HDPE pipe Sizes from 2 x ½750 x 15 mm through 8 x 4/200 x 100 mm IMPORTANT NOTES: Style 920 and Style 920N housings cannot be mated to one another to achieve cross connections. IPS CARBON STEEL PIPE - HOLE CUT PRODUCTS 11.02 Mechanical-T® Bolted Branch Outlets STYLES 920 AND 920N DIMENSIONS UFO AL" 1717m, Mm rim 1h (a) 920N 500 1.50 2.00 2.53 1.61 5.35 2.75 3.1 50 15 3450 38.1 51 - 64 41 136 70 1.5 - 1/4 (a) 920N 500 1.50 1.97 2.53 1.61 5.35 2.75 3.1 20 3450 38.1 50 - 64 41 136 70 1.5 1 (a) 920N 500 1.50 1.85 2.53 1.61 5.35 2.75 3.0 25 3450 38.1 47 - 64 41 136 70 1.4 - 1 ¼ (a) t 920N 500 1.75 2.05 2.75 3.00' 1.61 5.35 3.00 3.5 3.2 32 3450 44.5 52 70 76 41 136 76 1.7 1.5 114 (a) t 920N 500 1.75 2.03 2.75 3.12 1.61 5.35 3.25 3.6 3.2 40 920N 3450 500 44.5 1.50 52 2.21 70 79 2.74 41 91.82 136 5.64 83 2.75 1.7 3.0 1.5 21/2 ½ (a) 65 15 3450 38.1 56 - 70 46 143 70 1.4 - 3/4 (a) 920N 500 1.50 2.18 2.74 1.82 5.64 2.75 3.0 20 3450 38.1 55 - 70 46 143 70 1.4 - 1(a) 920N 500 1.50 2.06 2.74 1.82 5.64 2.75 2.9 25 3450 38.1 52 - 70 46 143 70 1.4 - 1¼ t (a) 920N 500 1.75 2.30 3.00 3.25 1.82 6.29 3.00 3.5 3.2 32 3450 44.5 58 76 83 46 160 76 1.7 1.5 11/2 t (a) 920N 500 2.00 2,28 3.00 3.25 1.82 6.26 3.25 3.6 3.3 40 920 3450 300 50.8 1.50 58 2.22 76 83 2.75 46 2.25 159 6.46 83 3.18 1.7 3.9 1.6 ½ (a) 76.1 x 15 2065 38.1 56 - 70 57 164 81 1.8 - 3/4 (a) 920 300 1.50 2.19 2.75 2.25 6.46 3.18 3.9 20 2065 38.1 56 - 70 57 164 81 1.8 - 1(a) 920 300 1.50 2.07 2.75 2.25 6.46 3.18 3.8 25 2065 38.1 53 - 70 57 164 81 1.7 - 1 ¼ (a) 920 500 1.75 2.30 3.00 3.31 1.92 6.29 3.00 3.5 3.2 32 3450 44.5 58 76 84 49 160 76 1.6 1.5 1½ (a) 920 500 2.00 2.28 3.00 3.31 1.92 6.29 3.25 3.5 3.3 40 920N 3450 500 50.8 1.50 58 2.52 76 84 3.05 49 2.28 160 6.15 83 2.75 1.6 3.4 1.5 1/2 (a) 80 15 3450 38.1 64 - 78 58 156 70 1.6 - 1/4 (a) 920N 500 1.50 2.49 3.05 2.28 6.15 2.75 3.4 20 3450 38.1 63 - 78 58 156 70 1.6 - 1 (a) 920N 500 1.50 2.38 3.06 2.28 6.15 2.75 3.3 25 3450 38.1 61 - 78 58 156 70 1.6 - 11/4 (a) t) 920N 500 1.75 2.55 3.25 3.56 2.28 6.15 3.00 3.8 3.7 32 (b 3450 44.5 65 83 90 58 156 76 1.8 1.8 1 1/2 (a) t 920N 500 2.00 2.78 3.50 3.56 2.28 6.15 3.25 4.1 3.8 40(b) 3450 508 71 89 90 58 156 83 1.9 1.8 2 (a) 920N 500 2.50 2.75 3.50 3.56 2.28 6.75 3.88 4.9 4.6 50 3450 63.5 70 89 90 58 172 99 2.3 21 2 920N 500 2.50 3.75 2.44 6.72 3.88 I 3.8 90 50 3450 63.5 - ( - 95 62 171 99 - 1.8 TABLE CONTINUED ON PG. 3 www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2007 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA. 11.02_2 j4tauiic' REV_i IPS CARBON STEEL PIPE - HOLE CUT PRODUCTS 11.02 Mechanical-i® Bolted Branch Outlets STYLES 920 AND 920N DIMENSIONS (Y _ Ô TABLE CONTINUED FROM PAGE 2 v 4 ½ (a) 920N 500 1.50 3.03 3.56 2.69 7.01 2.75 3.7 I 100 15 3450 38.1 77 90 - 68 178 70 1.8 - - - ~ (a) 920N 500 1.50 3.00 3.56 2.69 7.01 2.75 3.7 - 1 20 3450 38.1 76 90 - 68 178 70 1.8 - 1(a) 500 1.50 2.88 3.56 2.69 7.01 2.75 3.6 25 920N 3450 38.1 73 90 - 68 178 70 1.8 - GROOVED OUTLET 1 /4 (a) t 920N 500 1.75 3.08 3.78 4.00 2.69 7.01 3.00 4.0 3.6 32(b) 3450 44,5 78 96 102 68 178 76 1.9 1.8 1 1/z (a) t 500 2.00 3.28 4.00 4.00 2.69 7.01 3.25 4.2 3.9 V I4-z---91 40(b) 920N 3450 50.8 83 102 102 68 178 83 2.0 1.9 2(a) t ON 500 2.50 3.25 4.00 4.00 2.69 7.01 3.88 5.0 4.6 so 92 3450 63.5 83 102 102 68 178 99 2.3 21 V 1 214 (a) t 500 2.75 2.88 4.00 4.00 2.69 7.34 4.63 5.8 5.0 65 920 3450 69.9 73 102 102 68 186 118 2.6 2.3 920 500 2.75 4.00 2.69 7.34 4.63 6.4 w 76.1 mm 1? 34.510 69.9 - - 102 68 186 118 - 2.9 4' 3 (a) t 500 3.50 3.31 4.50 4.12 2.69 7.73 5.12 8.4 6.4 80 920 3450 88.9 84 114 105 68 196 130 3.8 2.9 FEMALE THREADED OUTLET 1 14(a) 920N 500 1.75 3.08 3.78 2.63 7,64 3.05 5.0 108.0 x 32 3450 44.5 78 96 - 67 194 78 2.3 - 1 ½ (a) 500 2.00 3.28 4.00 2.63 7.64 3.25 5.0 Provides a direct branch connection at 40 920N 3450 50.8 83 102 - 67 194 83 2.3 - any location where a hole can be cut 2(a) 920N 500 2.50 3.25 4.00 - 2.63 7.64 4.00 4.0 - in the pipe 50 3450 63.5 83 102 67 194 102 1.9 500 2.75 2.88 4.00 4.00 2.63 7.64 4.29 8.0 A pressure responsive gasket provides . mm 3450 69.9 73 102 102 67 194 109 3.6 - the seal 3 (a) 920 500 3.50 3.31 4.50 - 2.63 7.63 4,88 6.8 6.5 80 3450 88.9 84 114 67 194 124 3.1 3.0 Request Publication 11.03 for 5 1½ (a) t 920 500 2.00 4.03 4.75 4.75 3.16 9.70 3.69 7.4 7.6 Mechanical-T cross assemblies 125 X 40 3450 50.8 102 121 121 80 246 94 3.4 3.4 2 (a) t 500 2.50 4.00 4.75 4.75 3.16 9.70 4.38 8.2 8.0 Pressure rated up to 500 psi/3450kPa 50 920 3450 63.5 102 121 121 80 246 111 3.7 3.6 on steel pipe; also available for use 21/2 (a) t 920 500 2.75 3.63 4.75 4.75 3.16 9.70 4.63 8.3 7.9 with HDPE pipe 65 3450 69.9 92 121 121 80 246 118 3.8 3.6 76.1 mm 920 500 2.75 - - 4.75 3.16 9.70 4.63 - 8.0 Sizes from 2 x ½ /50 x 15mm 3450 69.9 121 80 246 118 3.6 through 8 x 4/200 x 100 mm 3 (a) t 920 500 3.50 3.81 5.00 4.63 3.16 9.70 5.31 8.4 8.8 80 3450 88.9 97 127 118 80 246 135 3.8 4.0 13 3.0 2 920N 500 2.50 3.75 4,50 3,17 8.00 3.88 8.0 . x 50 3450 63.5 95 114 - 81 203 99 3.6 920 500 3.50 181 5.00 3.00 9.46 5.31 8.0 - 80 3450 88.9 97 127 - 76 240 135 3.6 TABLE CONTINUED ON PG. 4 IMPORTANT NOTES: Style 920 and Style 920N housings cannot be mated to one another to achieve cross connections. www.vuCtaulic.com vicTAuLic IS A-REGiSTERED TRADEMARK OF VICTAULIC COMPANY. © 2007 VICTAuLiC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA. ictaulu C REV_i 11.02_3 PS CARBON STEEL PIPE - HOLE CUT PRODUCTS 11.02 MechanicalT® Bolted Branch Outlets STYLES 920 AND 920N DIMENSIONS 139.7 Y z 11i[OHN TABLE CONTINUED FROM PAGE 3 1 ½ t 500 2.00 3.78 4.50 3.30 8.23 3.25 7.0 40 920N 3450 50.8 96 114 - 84 209 83 3.2 - 2 920N 500 2.50 3.75 4.50 3.30 8.23 3.88 9.0 50 3450 63.5 95 114 - 84 209 99 4.1 C-1--viv 76.1 mm 920 - 500 2.75 3.63 4.75 3.13 9,85 4.63 8.8 3450 69.9 92 121 - 80 250 118 4.0 - GROOVED OUTLET 76.1 mm 920 500 3.50 4.63 3.16 9.70 5.31 11.0 - 3450 88.9 - - 118 80 246 135 5.0 920 500 3.50 3.81 5.00 4.63 3.16 9.85 5.38 14.0 14.2 Y Z 88.9 3450 88.9 96.80 127 118 80 250 137 6.4 6.4 6 11/4(a) 920N 500 1.75 4.43 3.79 9.15 3.25 4.8 150 32 (b) 3450 44.5 112 - - 96 232 0 83 - 2.2 T IR 50 3450 63.5 111 130 130 96 232 99 2.7 2.5 --n 1½ (a) t 920N 500 2.00 4,40 5.13 5.13 3.79 9.15 3.25 5.4 5.1 4) - 40(b) 3450 50.8 112 130 130 96 232 83 2,4 2.3 2(a) 920N 500 2.50 4.38 5.13 5,13 3.79 9.15 3.88 6.0 5.6 21/2 (a) t 920 500 2.75 4.01 5.13 5.12 3.69 10.51 4.63 8.3 7.6 65 3450 69.9 110 130 130 94 267 118 3.8 3.4 FEMALE THREADED OUTLET 76.1 mm 920 500 2.75 5.21 3.69 10.51 4.63 8.4 3450 69.9 - - 132 94 267 118 - 3.8 3 (a) t920 500 3.50 4.31 5.50 5.13 3.69 10.51 5.31 9.9 8.4 Provides a direct branch connection at 80 3450 88.9 110 140 130 94 267 135 4.5 3.8 any location where a hole can be cut 4(a) t 920 500 4.50 3.81 5.75 5.38 3.69 10.51 6.25 10.1 10.1 in the pipe 100 3450 114.3 97 146 137 94 267 159 4.6 4.6 1¼ 500 1.75 4.43 5.13 3.63 9.40 3.25 9.0 8.7 A pressure responsive gasket provides x 32 920N 3450 44.5 113 130 - 92 239 83 4.1 4.0 the sea) 1 ½ (a) 920N 500 2.00 4.41 5.13 3.63 9.40 3.25 7.8 40 3450 50.8 112 130 - 92 239 83 3.5 - Request Publication 11.03 for 920N 500 2.50 4.38 5.13 3.63 9.40 3.88 8.0 Mechanical-T cross assemblies 50 3450 63.5 111 130 - 92 239 99 3.6 - 500 2.75 4.38 5.50 513 363 9.40 4.63 9.5 9.5 Pressure rated up to 500 psi/3450 kPa 76.1mm 920 3450 699 111 140 130 92 239 118 4.3 4.3 on steel pipe; also available for use 3 920 500 3.50 4.31 5.50 5.13 3.63 9.40 5.31 8.1 14.0 with HDPE pipe 80 3450 88.9 110 140 130 92 239 135 3.7 6.4 108.1 mm! 920 500 4.50 5.38 3.63 9.40 6.12 10.0 3450 114.3 - - 137 92 239 155 - 4.5 through 8 x 4/200 x 100 mm 4 Sizes from 2 x ½750 x 15 mm -H 920 500 4.50 3.81 5.75 3.63 9.40 6.25 18.0 - 100 3450 114.3 96.80 146 - 92 239 159 8.2 TABLE CONTINUED ON PG. 5 IMPORTANT NOTES: Style 920 and Style 920N housings cannot be mated to one another to achieve cross connections. www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 2007 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA. /ictaulid 11.02_4 REVJ IPS CARBON STEEL PIPE - HOLE CUT PRODUCTS 11.02 Mechanical-I® Bolted Branch Outlets STYLES 920 AND 920N dimensions '' 4 TABLE CONTINUED FROM PAGE 4 1 920 500 150 3.88 4.56 3.79 9.34 2.75 8.0 165.1 x 25 3450 38.1 99 116 - 96 237 70 3.6 11/4 920 500 1.75 4.43 5.13 3.79 9.34 3.25 8.4 32 3450 44.5 113 130 - 96 237 83 3.8 1 ½ (a) t 920 500 2.00 4.41 5.13 3.79 9.34 3.25 8.4 40 3450 50.8 112 130 - 96 237 83 3.8 GROOVED OUTLET 2 (a) 6 500 2.50 4.38 5.13 3.79 9.34 3.88 8.5 920 50 3450 63.5 111 130 - 96 237 99 3.9 21/2 t 920 500 2.75 4.01 5.13 3.63 10.51 4.63 8.6 65 3450 69.9 110 130 - 92 267 118 3.9 500 2.75 4.01 5.13 5.21 3.63 10.51 4.63 8.6 76.1 mm 920 b __ 3450 69.9 110 130 132 92 267 118 3.9 3(a) t 920 500 3.50 4.31 5.50 5.13 3.63 10.51 5.31 10.2 80 3450 88.9 110 140 130 92 267 135 4.6 4 (a) 920 500 4.50 3.81 5.75 5.38 3.63 10.51 6.25 10.5 100 3450 114.3 97 146 137 92 267 159 4.8 -n 8 200 X 2(a) 920 500 2.75 5.44 6.19 6.25 4.81 12.42 4.50 11.6 50 3450 69.9 138 157 159 122 316 114 5.3 FEMALE THREADED OUTLET 21h (a) t 920 500 2.75 5.07 6.19 6.19 4.81 12.42 4,50 11.6 65 3450 69.9 129 157 157 122 316 114 5.3 500 2.75 6.25 4.81 12.42 4.56 Provides a direct branch connection at 76.1 mm 920 3450 69.9 - 159 122 316 116 - any location where a hole can be cut 3 (a)t 920 500 3.50 5.31 6.50 6.50 4.81 12.42 5.31 12.6 in the pipe 80 3450 88.9 135 165 165 122 316 135 5.7 4 (a) t 920 500 4.50 4.81 6.75 6.38 4.81 12.42 6.25 15.3 A pressure responsive gasket provides 100 3450 114.3 122 171 . 162 122 316 159 6.9 the seal center of run to engaged pipe end, female threaded outlet only (dimensions approximate). • Request Publication 11.03 for t Available with grooved or female threaded outlet. Specify choice on order. Mechanical-T cross assemblies * center of run to end of fitting. # Female threaded outlets are available to NPT and BSPT specifications. • Pressure rated up to 500 psi/3450 kPa (a) British Standard female pipe threaded outlet is available as listed. Specify "BSPT" clearly on order. on steel pipe; also available for use (b)For 76.1 mm threaded outlet, specify 21/2" BSPT clearly on order. with HDPE pipe • Sizes from 2 x ½/SO x 15mm through 8 x 4/200 x 100 mm 7.6 3.4 7.6 3.4 8.4 3.8 8.4 3.8 11.6 5.3 11.6 5.3 11.6 5.3 11.6 5.3 12.5 5.7 IMPORTANT NOTES: Style 920 and Style 920N housings cannot be mated to each other to achieve cross connections. www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2007 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA. X04-c-ta -U1 ii I:f REVJ 11.025 PS CARBON STEEL PIPE - HOLE CUT PRODUCTS 11.02 MechanicalT® Bolted Branch Outlets STYLES 920 AND 920N FLOW DATA Flow test data has shown that the total head loss between point (1) and (2) for the Style 920, 920N and 929 MechanicalT® fittings can best be expressed in terms of the pressure difference across the inlet and branch. The pressure difference can be obtained from the relationship below. C, Values Values for flow of water at +60°F/+16°C are shown in the table below. Exaggerated for clarity J P - ½ 0.840 2.0 15 21.3 - 0.6 3/~ 1.050 4.0 20 26.7 - 1.2 1 1.315 5.0 25 33.7 - 1.5 1¼ 1.660 5.5 6.0 -__32 42.4 1.7 1.8 1½ 1.900 7,0 8.0 40 48.3 2.1 2.4 Formulas for C, Values: AP = Where: Q = Flow (GPM) AP = Pressure Drop (psi) Q = C x C = Flow Coefficient 2 2.375 9.0 10.5 50 60.3 2.875 2.7 11.0 3.2 12.5 21/2 65 73.0 3.500 3.4 13.5 3.8 15.5 3 80 88.9 4.500 4.1 20.0 4.7 22.0 4 100 114.3 6.1 6.7 Size CV Actual Nrnina1 Outside ___ Srz DiSiSiSter Inches1mm Inchesfmm Vali9? Size CV Actual Nominal OutSide Size Diameter lntheslmm Inches/mm •VaIi9? Size CV Actual Nominal Outside Size Diameter lnchesfmm Incheslmm Values 0.840 15 21.3 1vI 42.4 2.875 73.0 135 1/4 1.050 I 7 21 1.900 I 3 60 3.500 88.9 200 L 1 1.315 25 AI 100 2,375 4.500 1'II www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2007 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA. 11.02_6 REVJ IPS CARBON STEEL PIPE - HOLE CUT PRODUCTS 11.02 Mechanical-T® Bolted Branch Outlets STYLES 920 AND 920N APPROVED PRESSURE RATINGS The information provided below is based on the latest listing and approval data at the time of publi- cation. Listings/Approvals are subject to change and/or additions by the approvals agencies. Contact Victaulic for performance on other pipe and the latest listings and approvals. Run - .- Size Outlet Size Rated Working Pressures — i 21/2-6 araI rn, P 2.875-6.625 All 1040 400 400 400 65 -150 73.0 -168.3 2.875 - 4.500 All DF 2755 300 2755 300 2755 300 21/2-4 65-100 73.0-114.3 2.875 - 4.500 All SF 2065 300 2065 300 2065 300 21/2-4 65-100 73.0-114.3 6.625 3,4 10 2065 300 2065 300 2065 250 6 150 168.3 6.625 34 3040 2065 300 2065 300 1724 300 6 150 168.3 8.625 21/2 10,40 2065 400 2065 - 2065 - 8 200 219.1 8.625 34 10 2755 300 - 250 8 200 219.1 8.625 34 30,40 2065 300 - 1724 300 8 200 219.1 2065 . 2065 NOTES: 10 refers to Listed/Approved Schedule 10 steel sprinkler pipe. 40 refers to Listed/Approved Schedule 40 steel sprinkler pipe. OF refers to Listed/Approved Dyna-Flow steel sprinkler pipe manufactured by American Tube Company. SF refers to Listed/Approved Super-Flo steel sprinkler pipe manufactured by Allied Tube and Conduit Corporation. VIC-TAP II HOLE CUTTING TOOL FOR The Vic-Tap II hole cutting tool is designed for use with the Style 931 Vic-Tap II Mechanical-T unit, 4 - 8/100 - 200 MM CARBON STEEL PIPE which is a combination of the Style 920 Mechanical-T and Series 726 Vic-Ball Valve. The Vic-Tap II is capable of tapping into carbon steel pipe systems under pressures up to 500 psi/3450 kPa. I The Style 931 Vic-Tap II Mechanical-T unit is a full port ball valve which can be mounted on 4/100mm, ' 5/125mm, 67150mm and 8'7200 mm diameter pipe. The Style 931 comes with a 2½765mm grooved outlet. . The drill motor is an electric motor with ground fault circuit interrupter (GFCl) in accordance with safety codes. For more information, refer to publication 24.01. www.victaulic.com . VIcTAuLIc IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2007 vrcTAuLlc COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA. ictaul.c REVJ 11.02_7 STYLES 920 AND 920N INSTALLATION Reference should always be made to the 1-100 Victaulic Field Installation Handbook for the product you are installing. Handbooks are included with each shipment of Victaulic products for complete installation and assembly data, and are available in PDF format on our website at www.victaulic.com. WARRANTY Refer to the Warranty section of the current Price List or contact Victaulic for details. NOTE This product shall be manufactured by Victaulic or to Victaulic specifications. All products to be installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations. II IIIIIIIIIIIIIIIIIIIIHIIIIIIIlIIIIIIIIII WCAS-6YCLDG For complete contact information, visit www.victaulic.com 11.02 1480 REV J UPDATED 4/2007 Ataulic' vIcTAuLIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2007 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA. 11.02_8 -SWG 20 Maximum pipe size in composite wood joist allowed by UL is 2-1/2' "SWG 20 Maximum pipe size in woxd Umber or joist allowed by UL is 2-1/2' SXP 20 Maximum allowable angle in 22 ga. steel is 450 UL and FM tests were performed in compliance with NFPA 13 Standards. Fastening requirement 5 times weighth of water filled schedule 40 pipe 250 pounds. K\ IThWBUIIdeX www.itwbuildex.com 800-BUI LDEX SSS39 082007 8007957 GST 10 X CPVC 1-1/2 300 tL 1.5 8020957 SWG 10 X CPVC 1-1/2 300 1.5 8008957 GST20 X 2-1/2 850 1.5 X 4 1475 1.5 8068925 GST20SS X 2-1/2 850 1.5 8010957 GST30 X 4 1500 1.5 X 4 1475 1.5 8009925 GST25-380 X 4 1500 1.5 8022925 SWG 25-380 X 3-1/2-4' 1500 1.5 8021957 SWG 20 X 2-1/2 - 3** 1250 1.5 8073925 SWG 2OSS X 2-1/2 1250 1.5 8139957 SHGST20 X 3 1050 1.5 X 4 1475 1.5 8141957 SHGST30 X 4 . 1500 1.5 X 4 1475 1.5 -NINFOWEENER-1 Ism 8038957 DSTR1 X 4 1500 .035 X 4 1475 .1050 8037957 DSTR 1-1/2 X 4 1500 .035 X 4 1475 .1050 8039957 DSTR 516 X 4 1500 .037 X 4 1475 .1050 8045957 DST 516 X 4 1500 .188 X 4 1475 .1875 8046957 TEK50 X 4 1500 .250 X 4 1475 .1875 8055957 SWDR1 X 4 1500 .037 X 4 1475 .0600 8056957 SWDR 516 X 4 1500 .037 X 4 1475 .0600 8054957 SWDR 1-1/2 X 4 1500 .037 X 4 1475 .0600 8137957 SH DSTR 1 X 4 1500 .035 X 4 1475 .1050 8150922 XP 20 X 2-1/2 850 .027 X 4 1475 .1050 8153922 XP 35 X 3-1/2 1250 .043 X 4 1475 .1050 8294922 SXP 20A X 2 750 .027 X 4 1475 8295922 SXP35 X 3-1/2 1250 .060 X 4 1475 8293957 SWXP35 X 3-1/2 1250 .060 X 4 1475 UL-Mix Pipe ULTest' FM Max FM Test Part No. Concrete UL Mm. PSI FM' Mate Size, Load PmpeSize Lod _a 8059957 CST 20 3000 X 4 1475 3000 PSI 8061957 SWC20 3000 X 4 1475 3000 PSI 8150922 XP 20 X 2-1/2 850 Pre Pour Structural 3000 PSI 8150922 XP 20 X 2-1/2 850 Post Pour Range II LWC <35 PCF SWG 25-380 Maximum pipe size in composite wood joist allowed by UL is 3-1/2 'SWG 25-380 Maximum pipe size in wood Umber or joist allowed by UL is 4° IMPERIAL MAX REC. LOAD LBS. METRIC* PIPE ROD PIPE ROD 112 3/8 400 10 3/4 g 400 20 10 1 3/8 400 25 10 11/4 3/8 400 32 to 1 1/2 3/8 400 40 10 2 3/8 400 50 10 21/2 318 600 65 10 3 3/8 600 80 10 31/2 3/8 600 10 4 3/8 1000 100 1 to 1/2 1250 125 12 6 1250 150 8 1/2 1250 200 1 12 * Order Part #300m Note: 1/2 Ring Hanger not <EM> approved fzJ P.O. Box 3365 South El Monte, CA 91733 626.444.0541 Fax 626.444.3887 www. Afcon.org ucl RING HANGER I thru 4 Inch pipe LISTED FOR STEELJCPVC 112 and 3/4 Inch pipe 5 thru 8 Inch pipe SIZE - 1/2 thru 8 inch pipe. MATERIAL - Carbon Steel, Mu. Galvanized to G-90 spec. LISTING/APPROVAL - 203-EX 2551 Approval guide - Pipe Hangers OSHPD OPA-0601 See Website. CONFORMS WITH: Federal Specification WW-H-171 (Type 10, Manufacturers Standardization Society ANSI/MSS-SP-58 (Type 10). MAXIMUM TEMPERATURE - 650°F. FUNCTION - Pipe hanger component for use on steel, CPVC or copper piping. INSTALLATION - Per NFPA-13, 13R and 13D. FEATURES - * Sized and listed exclusively for use with #310 Surge Restrainer. * Band edge is offset for EASY pipe insertion. * Custom fit swivel nut for better retention in ring body. * Full length knurl on swivel nut for better grip. ORDERING - Part #, pipe size. 2/07 tqCU /Fire & Building I Products Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500 Series ELO-231B - 112 K-factor Upright and Pendent Sprinklers Standard Response, Standard Coverage General Description The 11.2 K-factor, Series EL0-23113, Standard Response, Standard Cover- age, Upright and Pendent Sprinklers (Ref. Figure 1) are automatic sprin- klers of the frangible bulb type. They are "standard response - spray sprin- klers" that produce a hemispherical water distribution pattern below the deflector. The 11.2 K-factor, ELO-231B Sprin- klers were subjected to full scale, high- piled storage, fire tests to qualify their use in lieu of 5.6 or 8.0 K-factor stand- ard spray sprinklers for the protection of high-piled storage. Higher flow rates can be achieved at much lower pressures with the 11.2 K-factor, ELO-231B Sprinklers - making their use highly advantageous in high density applications, such as the protection of high-piled storage. Wax or lead coatings can be used to extend the life of the copper alloy com- ponents used in Series ELO-231B sprinklers beyond that which would otherwise be obtained when exposed to corrosive atmospheres. Although wax, lead, and polyester coated sprin- klers have passed the standard corro- sion tests of the applicable approval agencies, the testing is not repre- IMPORTANT Always refer to Technical Data Sheet TFP 700 for the "INSTALLER WARNING" that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and in- stallation can permanently damage a sprinkler system or its compo- nents and cause the sprinkler to fail to operate in a tire situation or cause it to operate prematurely. sentative of all possible corrosive at- mospheres. Consequently, it is recom- mended that the end user be consulted with respect to the suitability of these corrosion resistant coatings for any given corrosive environment. The ef- fects of ambient temperature, concen- tration of chemicals, and gas/chemical velocity, should be considered, as a minimum, along with the corrosive na- ture of the chemical to which the sprin- klers will be exposed. An upright intermediate level version of the Series ELO-231 B Sprinklers for in-rack applications can be obtained by utilizing the Series ELO-231B Up- right Sprinkler with the WSG-2 Guard & Shield, and a pendent intermediate level version of the Series ELO-231 B Sprinklers can be obtained by utiliz- ing the Series ELO-231B Pendent Sprinkler with the WS-2 Shield. If there is a possibility of the pendent interme- diate level version being exposed to mechanical damage, a G-2 Guard can be added. WARNINGS The 11.2 K-factor, Series ELO-231B Upright and Pendent Sprinklers de- scribed herein must be installed and maintained in compliance with this document, as well as with the applica- ble standards of the National Fire Pro- tection Association, in addition to the standards of any other authorities hav- ing jurisdiction. Failure to do so may impair the performance of these de- vices. The owner is responsible for main ta/n- ing their fire protection system and de- vices in proper operating condition. The installing contractor or manufac- turer should be contacted with any questions. Installation of Series EL 0-23 lB Pen- dent Sprinklers in recessed escutch- eons will void all sprinkler warranties, as well as possibly void the sprinkler's Approvals and/or Listings. Page 1 of 6 MARCH, 2007 TFP342 Page 2 of 6 TFP342 SPRINKLER FINISH TYPE TEMPERATURE BULB LIQUID NATURAL BRASS I CHROME PLATED LEAD I COATED WAX COATED WAX OVER LEAD UPRIGHT (TY5151 & TY5851) 155°F/68°C Red 1,2,3,4 3 200°F193°C Green 286F/141°C Blue I PENDENT (TY5251 155°F/68°C Red 1,2,3,4 3 200FI93C Green 286°F/141°C Blue 3(a) NOTES: Listed by Underwriters Laboratories, Inc. (UL Listed). Listed by Underwriters Laboratories, Inc. for use in Canada (C-UL Listed). Approved by Factory Mutual Research Corporation (FM Approved). Approved by the City of New York under MEA 291-04-E. (a). FM Approved for a maximum ceiling temperature of 150°F/66°C. TABLE A LABORATORY LISTINGS AND APPROVALS FOR 11.2 K-FACTOR SERIES ELO-231B UPRIGHT AND PENDENT SPRINKLERS (Refer to the Design Criteria Section) Model/Sprinkler Identification Numbers TY5151 - Upright 11.2K, 3/4NPT TY5251 - Pendent 11.2K, 3/4"NPT TY5851, - Upright 11.2K, 1/2"NPT TY5151 is a redesignation for C5151. TY5251 is a redesignation for C5251, G1871, and S2531. TY5851 is a redesignation for C5851. Technical Data Approvals UL and C-UL Listed. FM and NYC Ap- proved. (Refer to Table A for complete approval information including corro- sion resistant status. The approvals apply to the service conditions indi- cated in the Design Criteria section.) Maximum Working Pressure 175 psi (12,1 bar) Discharge Coefficient K = 11.2 GPM/psi112 (161,4 LPM/barl'2) Temperature Ratings Refer to Table A Finishes Refer to Table A Physical Characteristics Frame .............Bronze Cap ..............Bronze Sealing Assembly ........... Beryllium Nickel w/Teflont Bulb (5 mm dia.) .......Glass Compression Screw .....Bronze Deflector ............Bronze t Registered trademark of DuPont. Design Criteria UL and C-UL Listing Requirements The 11.2 K-factor, Model ELO-231 B (TY5151, TY5251 & TY5851) Sprin- klers are to be installed in accordance with NFPA 13 standard sprinkler posi- tion and area/density flow calculation requirements for light, ordinary, or ex- tra hazard occupancies, as well as high piled storage occupancies (solid piled, palletized, rack storage, bin box, and shelf storage including but not lim- ited to Class l-IV and Group A plastics) with a minimum residual (flowing) pressure of 7 psi (0,5 bar) for wet or dry pipe systems. FM Approval Requirements The 11.2 K-factor, Model ELO-231B (TY5151, TY5251 & TY5851) Sprin- klers are to be installed in accordance with the applicable "control mode den- sity/area" guidelines provided by Fac- tory Mutual. (FM guidelines may differ from UL and C-UL Listing criteria.) TFP342 Page 3 of 6 * Temperature rating is indicated on deflector. ** Pipe thread connections per ISO 7/1 can be provided on 1/2 (12,7 mm) special request. NOMINAL MAKE-IN T--A 2-13/16"t W (71,4 mm) RENC FLATS P. 112** I NPT t.. 7/16(11,1 mm) fIII NOMINAL MAKE-IN 11 Components - Frame 2 - Seal Assembly Cap Bulb Compression Screw 6 - Deflector* UPRIGHT UPRIGHT PENDENT CROSS TY5851 TY5151 TY5251 SECTION FIGURE 1 11.2 K-FACTOR SERIES ELO-231B UPRIGHT - 3/4" NPT (TY5151), UPRIGHT - 1/2" NPT (TY5851), AND PENDENT - 3/4" NPT (TY5251) SPRINKLERS Operation The glass bulb contains a fluid that expands when exposed to heat. When the rated temperature is reached, the fluid expands sufficiently to shatter the glass bulb, allowing the sprinkler to activate and water to flow. Installation The Series ELO-231 B Sprinklers must be installed in accordance with the fol- lowing instructions: NOTES Do not install any bulb type sprinkler if the bulb is cracked or there is a loss of liquid from the bulb. With the sprinkler held horizontally, a small air bubble should be present. The diameter of the air bubble is approximately 1/16 inch (1,6 mm) for the 155°F/68°C to 3/32 inch (2,4 mm) for the 286°F/141°C temperature ratings. A leak tight 3/4 inch NPT sprinklerjoint should be obtained with a torque of 10 to 20 ft.lbs. (13,4 to 26,8 Nm). A maxi- mum of 30 ft.lbs. (40,7 Nm) of torque is to be used to install sprinklers with 3/4 NPT connections. A leak tight 1/2 inch NPT sprinkler joint should be ob- tained with a torque of 7 to 14 ft.lbs. (9,5 to 19,0 Nm). A maximum of 21 ft. lbs. (28,5 Nm) of torque may be used to install sprinklers with 1/2 NPT con- nections. Higher levels of torque may distort the sprinkler inlet and cause leakage or impairment of the sprinkler. Do not attempt to make-up for insuffi- cient adjustment in the escutcheon plate by under- or over-tightening the sprinkler. Readjust the position of the sprinkler fitting to suit. The Series ELO-231B Upright and Pendent Sprinklers must be installed in accordance with the following in- structions. Step 1. Pendent sprinklers are to be "FITTING SIDE" TOWARDS SPRINKLER FITTING WRENCH RECESS (END "A") FIGURE 2 W-TYPE 3 SPRINKLER WRENCH installed in the pendent position, and upright sprinklers are to be installed in the upright position. Step 2. With pipe thread sealant ap- plied to the pipe threads, hand tighten the sprinkler into the sprinkler fitting. Step 3. Tighten the sprinkler into the sprinkler fitting using only the W-Type 3 Sprinkler Wrench (Ref. Figure 2), except that an 8 or 10 inch adjustable Crescent wrench is to be used for wax coated sprinklers. With reference to Figure 1, the W-Type 3 Sprinkler Wrench or the adjustable Crescent wrench, as applicable is to be applied to the wrench flats. When installing wax coated sprinklers with the adjustable Crescent wrench, additional care needs to be exercised to prevent damage to the wax coating on the sprinkler wrench flats or frame arms and, consequently, exposure of Page 4 of 6 TFP342 bare metal to the corrosive environ- ment. The jaws of the wrench should be opened sufficiently wide to pass over the wrench flats without damag- ing the wax coating. Before wrench tightening the sprinkler, the jaws of the wrench are to be adjusted to just con- tact the sprinkler wrench flats. After wrench tightening the sprinkler, loosen the wrench jaws before removing the wrench. After installation, the sprinkler wrench flats and frame arms must be in- spected and the wax coating re- touched (repaired) whenever the coat- ing has been damaged and bare metal is exposed. The wax coating on the wrench flats can be retouched by gen- tly applying a heated 1/8 inch diameter steel rod to the areas of wax that have been damaged, to smooth it back over areas where bare metal is exposed. NOTES Only retouching of the wax coating ap- plied to the wrench flats and frame arms is permitted, and the retouching is to be performed only at the time of the initial sprinkler installation. The steel rod should be heated only to the point at which it can begin to melt the wax, and appropriate precautions need to be taken, when handling the heated rod, in order to prevent the installer from being burned. If attempts to retouch the wax coating with complete coverage are unsuc- cessful, additional wax can be ordered in the form of a wax stick (the end of which is color coded). Only the correct color coded wax is to be used, and retouching of wrench flats and frame arms is only permitted at the time of initial sprinkler installation. With the steel rod heated as previously de- scribed, touch the rod to the area re- quiring additional wax with the rod an- gled downward, and then touch the wax stick to the rod approximately one-half inch away from the area re- quiring retouching. The wax will melt and run down onto the sprinkler. Care and Maintenance Series ELO-231B Sprinklers must be maintained and serviced in accord- ance with the following instructions: NOTES Before closing a fire protection system control valve for maintenance work on the fire protection system that it con- trols, permission to shut down the af- fected fire protection system must be obtained from the proper authorities and all personnel who maybe affected by this action must be notified. Sprinklers that are found to be leaking or exhibiting visible signs of corrosion must be replaced. Automatic sprinklers must never be painted, plated, coated or otherwise altered after leaving the factory. Modi- fied sprinklers must be replaced. Sprinklers that have been exposed to corrosive products of combustion, but have not operated, should be replaced if they cannot be completely cleaned by wiping the sprinkler with a cloth or by brushing it with a soft bristle brush. Care must be exercised to avoid dam- age to the sprinklers - before, during, and after installation. Sprinklers dam- aged by dropping, striking, wrench twist/slippage, or the like, must be re- placed. Also, replace any sprinkler that has a cracked bulb or that has lost liquid from its bulb (ref. Installation Section Note). Frequent visual inspections are rec- ommended to be initially performed for corrosion resistant sprinklers, after the installation has been completed, to verify the long term potential integrity of the sprinkler coatings. Thereafter, annual inspections per NFPA 25 should suffice; however, instead of in- specting from the floor level, a random sampling of close-up visual inspec- tions should be made, so as to better determine the exact sprinkler condi- tion and the long term integrity of the corrosion resistant coating, as it may be affected by the corrosive conditions present. The owner is responsible for the in- spection, testing, and maintenance of their fire protection system and de- vices in compliance with this docu- ment, as well as with the applicable standards of the National Fire Protec- tion Association (e.g., NFPA 25), in addition to the standards of any other authorities having jurisdiction. The in- stalling contractor or sprinkler manu- facturer should be contacted relative to any questions. It is recommended that automatic sprinkler systems be inspected, tested, and maintained by a qualified Inspection Service in accordance with local requirements and/or national code. Limited Warranty Products manufactured by Tyco Fire & Building Products (TFBP) are war- ranted solely to the original Buyer for ten (10) years against defects in mate- rial and workmanship when paid for and properly installed and maintained under normal use and service. This warranty will expire ten (10) years from date of shipment by TFBP. No warranty is given for products or com- ponents manufactured by companies not affiliated by ownership with TFBP or for products and components which have been subject to misuse, improper installation, corrosion, or which have not been installed, maintained, modi- fied or repaired in accordance with ap- plicable Standards of the National Fire Protection Association, and/or the standards of any other Authorities Having Jurisdiction. Materials found by TFBP to be defective shall be either repaired or replaced, at TFBP's sole option. TFBP neither assumes, nor authorizes any person to assume for it, any other obligation in connection with the sale of products or parts of prod- ucts. TFBP shall not be responsible for sprinkler system design errors or inac- curate or incomplete information sup- plied by Buyer or Buyer's repre- sentatives. In no event shall TFBP be liable, in contract, tort, strict liability or under any other legal theory, for incidental, indirect, special or consequential dam- ages, including but not limited to labor charges, regardless of whether TFBP was informed about the possibility of such damages, and in no event shall TFBP's liability exceed an amount equal to the sales price. The foregoing warranty is made in lieu of any and all other warranties. ex- of merchantability and fitness for a par- ticular ouroose. This limited warranty sets forth the ex- clusive remedy for claims based on failure of or defect in products, materi- als or components, whether the claim is made in contract, tort, strict liability or any other legal theory. A Part Number (P/N) is not specified when ordering sprinklers with thread connections per ISO 7/1. Contact your local distributor for avail- ability. Sprinkler Assemblies with NPT Thread Connection: Specify: (specify SIN), 11.2 K-factor, (specify temperature rating), Series ELO-231B Standard Response (spec- ify Pendent or Upright) Sprinkler with (specify finish), P/N (specify from Ta- ble B). Sprinkler Wrench: Specify: W-Type 3 Sprinkler Wrench, P/N 56-895-1 -001. 510 UPRIGHT 3/4" NPT (TY5151) 512 PENDENT 3/4" NPT (TY5251) 501 UPRIGHT 1/2" NPT (TY5851) TYPE SPRINKLER I TEMPERATURE RATING - 1 NATURAL BRASS 9 CHROME PLATED 155 155°F/68°C 6 WAX COATED 200 200°F/93°C 7 LEAD COATED 286 286°F/141°C 6 WAX OVER LEAD TFP342 Page 5 of 6 Ordering P/N 50-XXX-X-XXX Procedure Wax Sticks: (for retouching wrench damaged wax coating) Specify: (Specify color) color coded Wax Stick for retouching (specify tem- perature rating) temperature rated Se- ries ELO-231B Sprinklers, P/N (spec- ify). Red for 155°F ............. P/N 56-065-1-155 Blue for 200'F and 286'F ................. PIN 56-065-1-286 NOTES Each wax stick is suitable for retouch- ing up to twenty-five sprinklers. The wax used for 286°F sprinklers is the same as for 200°F sprinklers, and, therefore, the 286°F sprinkler is limited to the same maximum ceiling tempera- ture as the 200°F sprinkler (i.e., 150°F). TABLE B PRODUCTS YMBOL NUMBER SELECTION - 11.2 K-FACTOR SERIES ELO-231B STANDARD RESPONSE UPRIGHT AND PENDENT SPRINKLERS Page 6 of 6 TFP342 TYCO FIRE & BUILDING PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446 tqC0 /Fire & Building / Products Technical Services: Tel: (800) 381-9312/ Fax: (800) 791-5500 Series TY-FRB - 2.8,4.2,5.6, and 8.0 K-factor Upright, Pendent, and Recessed Pendent Sprinklers Quick Response, Standard Coverage General Description The Tyco® Series TY-FRB, 2.8, 4.2, 5.6, and 8.0 K-factor, Upright and Pen- dent Sprinklers described in this data sheet are quick response - standard coverage, decorative 3 mm glass bulb type spray sprinklers designed for use in light or ordinary hazard, commercial occupancies such as banks, hotels, shopping malls, etc. The recessed version of the Series TY-FRB Pendent Sprinkler, where ap- plicable, is intended for use in areas with a finished ceiling. It uses either a two-piece Style 10 (1/2 inch NPT) or Style 40 (3/4 inch NPT) Recessed Es- cutcheon with 1/2 inch (12,7 mm) of recessed adjustment or up to 3/4 inch (19,1 mm) of total adjustment from the flush pendent position, or a two-piece Style 20(1/2 inch NPT) or Style 30(3/4 inch NPT) Recessed Escutcheon with 1/4 inch (6,4 mm) of recessed adjust- ment or up to 1/2 inch (12,7 mm) of total adjustment from the flush pen- dent position. The adjustment pro- vided by the Recessed Escutcheon re- duces the accuracy to which the fixed pipe drops to the sprinklers must be cut. Corrosion resistant coatings, where applicable, are utilized to extend the life of copper alloy sprinklers beyond that which would otherwise be ob- IMPORTANT Always refer to Technical Data Sheet TFP 700 for the "INSTALLER WARNING" that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and in- stallation can permanently damage a sprinkler system or its compo- nents and cause the sprinkler to fall to operate in a fire situation or cause it to operate prematurely. tamed when exposed to corrosive at- mospheres. Although corrosion resis- tant coated sprinklers have passed the standard corrosion tests of the appli- cable approval agencies, the testing is not representative of all possible cor- rosive atmospheres. Consequently, it is recommended that the end user be consulted with respect to the suitability of these coatings for any given corro- sive environment. The effects of ambi- ent temperature, concentration of chemicals, and gas/chemical velocity, should be considered, as a minimum, along with the corrosive nature of the chemical to which the sprinklers will be exposed. An intermediate level versions of the Series TY-FRB Pendent Sprinklers are detailed in Technical Data Sheet TFP356, and Sprinkler Guards are de- tailed in Technical Data Sheet TFP780 WARNINGS The Series TY-FRB Sprinklers de- scribed herein must be installed and maintained in compliance with this document, as well as with the applica- ble standards of the National Fire Pro- tection Association, in addition to the standards of any other authorities hav- ing jurisdiction. Failure to do so may impair the performance of these de- vices. The owner is responsible for maintain- ing their fire protection system and de- vices in proper operating condition. The installing contractor or sprinkler manufacturer should be contacted with any questions. Model/Sprinkler Identification Numbers TYII3I - Upright 2.81K, 1/2"NPT TY1231 - Pendent 2.81K, 1/2"NPT TY2131 - Upright 4.21K, 1/2"NPT TY2231 - Pendent 4.2K, 1/2"NPT TY3131 - Upright 5.61K, 1/2"NPT TY3231 - Pendent 5.61K, 1/2"NPT TY4131 - Upright 8.01K, 3/4"NPT 1Y4231 - Pendent 8.01K, 3/4"NPT TY4831- Upright 8.0K, 1/2"NPT TY4931- Pendent 8.01K, 1/2"NPT Page 1 of 10 AUGUST, 2007 TFPI7I ESCUTCHEON PLATE SEATING SURFACE 7/16" (11,1 mm) NOMINAL 1/2" MAKE-IN NPT 2-1/4" \1 (57,2 mm) f çff2 1-9/16" (39,7 mm) SSP DEFLECTOR* Page 2 of 10 TFPI7I STYLE 10 or 20 RECESSED SSU* ESCUTCHEON DEFLECTOR 7/16 _: (11,1mm) NOMINAL MAKE-IN vi WRENCH (55,6mm) 2-3/16' " FLATS ' 7 1/2" NPT I PENDENT RECESSED PENDENT UPRIGHT CROSS SECTION 1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to 2 - Button Assembly 5 - Compression 7- Bushing orifice seat on frame. Screw FIGURE 1 QUICK RESPONSE SERIES TY-FRB UPRIGHT (TYI 131) AND PENDENT (TY1231) SPRINKLERS 2.8 K-FACTOR, 1/2 INCH NPT 7/16" (11,1 mm) 1/2" NOMINAL MAKE-IN NPT ESCUTCHEON PLATE SEATING SURFACE 2-J16,,_ (55,6 mm) 1-1/2" (38,1 mm) SSP DEFLECTOR* STYLE 100r20 RECESSED SSU* ESCUTCHEON DEFLECTOR 6* (11,1mm) 1 7/16" 5 I Lt.!!ii\ NOMINAL I ,, MAKE-IN 2-3/16" WRENCH _______ FLATS (55,6 mm) : 1/2" NPT I LW. 2-7/8" (73,0 mm) DIA. PENDENT RECESSED PENDENT UPRIGHT CROSS SECTION 1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to 2 - Button Assembly 5 - Compression orifice seat on frame. Screw FIGURE 2 QUICK RESPONSE SERIES TY-FRB UPRIGHT (TY2131) AND PENDENT (TY2231) SPRINKLERS 4.2 K-FACTOR, 112 INCH NPT ESCUTCHEON PLATE SEATING SURFACE 1I2 NPT 6*1 1/2" I (12,7 mm) I NOMINAL MAKE-IN I 2-1/4" (57,2 mm) 3 CROSS SECTION TFPI7I Page 3 of 10 F_ 2-3/16 (55,6 mm) T SSP DEFLECTOR* PENDENT 7/16" (11,1 mm) STYLE 100r20 NOMINAL MAKE-IN ESCUTCHEON DEFLECTOR RECESSED ssu 7/16" I (11,1 mm) Mr t\ I Jj) IVIrt-'IN 2-3/16" UFLATS WRENCH (55,6 mm) 2-7/8" (73,0 mm) DIA. —'-] 1/2" NPT RECESSED PENDENT UPRIGHT CROSS SECTION 1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to 2 - Button Assembly 5 - Compression orifice seat on frame. Screw FIGURE 3 QUICK RESPONSE SERIES TY-FRB UPRIGHT (TY3131) AND PENDENT (TY3231) SPRINKLERS 5.6 K-FACTOR, 1/2 INCH NPT STYLE 30 or 40 RECESSED SSU* ESCUTCHEON DEFLECTOR ESCUTCHEON 1/2(12,7mm) PLATE SEATING 3/4,, NOMINAL SURFACE MAKE-IN NPT 2-5/16" (58,7mm) It WRENCH HR fJl I I ____ LtL— Iii I 1-9/16" I (39,7 mm) L__ . FLATS SSP DEFLECTOR* 2-7/8" (73,0 mm) DIA. 3/4" NPT PENDENT RECESSED PENDENT UPRIGHT 1 - Frame 3 - Sealing 4- Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to 2 - Button Assembly 5 - Compression orifice seat on frame. Screw FIGURE 4 QUICK RESPONSE SERIES TY-FRB UPRIGHT (TY4131) AND PENDENT (TY4231) SPRINKLERS 8.0 K-FACTOR, 314 INCH NPT Page 4oflO TFPI7I 7/16(11,1 mm) NOMINAL SSU 1/2 NPT MAKE-IN DEFLECTOR 2-3 9!16 RENCHI (39,7 mm) FLATS ssP * DEFLECTOR CROSS PENDENT UPRIGHT SECTION 1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to 2 - Button Assembly 5 - Compression orifice seat on frame. Screw FIGURE 5 QUICK RESPONSE SERIES TY-FRB UPRIGHT (TY4831) AND PENDENT (TY4931) SPRINKLERS 8.0 K-FACTOR, 1/2 INCH NPT Technical Data Approvals UL and C-UL Listed. FM, LPCB, and NYC Approved. (Refer to Table A and B for complete approval information including corro- sion resistant status.) Maximum Working Pressure Refer to Table C. Discharge Coefficient K = 2.8 GPM/psi112 (40,3 LPM/barl/2) K = 4.2 GPM/psi112 (60,5 LPM/barl'2) K = 5.6 GPM/psi1/2 (80,6 LPM/barl'2) K = 8.0 GPM/p51112 (115,2 LPM/bar112) Temperature Ratings Refer to Table A and B Finishes Sprinkler: Refer to Table A and B. Recessed Escutcheon: White Coated, Chrome Plated, or Brass Plated. Physical Characteristics Frame .............Bronze Button .........Brass/Copper Sealing Assembly .......... Beryllium Nickel w/Teflont Bulb ...............Glass Compression Screw .....Bronze Deflector .......Copper/Bronze Bushing (K=2.8) .......Bronze Operation The glass Bulb contains a fluid which expands when exposed to heat. When the rated temperature is reached, the fluid expands sufficiently to shatter the glass Bulb, allowing the sprinkler to activate and water to flow. Design Criteria The Series TY-FRB Pendent and Up- right Sprinklers are intended for fire protection systems designed in ac- cordance with the standard installation rules recognized by the applicable Listing or Approval agency (e.g., UL Listing is based on the requirements of NFPA 13, and FM Approval is based on the requirements of FM's Loss Pre- vention Data Sheets ). Only the Style 10, 20, 30, or 40 Recessed Escutch- eon, as applicable, is to be used for recessed pendent installations. TFPI7I SPRINKLER FINISH (See Note 7) K TYPE TEMP. BULB LIQUID NATURAL BRASS I CHROME PLATED I WHITE* IPOLYESTER 2.8 1/2" PENDENT (TY1231) and UPRIGHT (TYII3I) 135°F/57°C Orange 1,2,3,5 155FI68°C Red 175F/79°C Yellow 2O0F/93°C Green 286F/141°C Blue NPT RECESSED PENDENT (TY1231)* Figure 6 135F/57'C Orange 1, 2, 5 155°F/68°C Red 175°F/79C Yellow 200F/93°C Green RECESSED PENDENT (TY1231)** Figure 7 135°F/57°C Orange 155°FI68C Red 175F/79°C Yellow 200°F/93°C Green 4.2 1/2" NPT PENDENT (TY2231) and UPRIGHT (TY2131) 135°F/57°C Orange 1,2 155F/68C Red 175F/79°C Yellow 200°F/93°C Green 286°F/141°C Blue RECESSED PENDENT (TY2231)* Figure 8 135°F/57'C Orange 155°F/68°C Red 175°F/79C Yellow 200°F/93°C Green RECESSED PENDENT (TY2231) Figure 9 135°F/57°C Orange 155°F/68°C Red 175F/79C Yellow 200°F/93°C Green NOTES: Listed by Underwriters Laboratories, Inc. (UL) as Quick Response Sprinklers. Listed by Underwriters Laboratories, Inc. for use in Canada (C-UL) as Quick Re- sponse Sprinklers. Approved by Factory Mutual Research Corporation (FM) as Quick Response Sprin- klers. 5. Approved by the City of New York under MEA 354-01-E. 7. Where Polyester Coated Sprinklers are noted to be UL and C-UL Listed, the sprin- klers are UL and C-UL Listed as Corrosion Resistant Sprinklers. * Installed with Style 10 (1/2" NPT) or Style 40 (3/4" NPT) 3/4" Total Adjustment Recessed Escutcheon, as applicable. ** Installed with Style 20 (1/2" NPT) or Style 30 (3/4" NPT) 1/2" Total Adjustment Recessed Escutcheon, as applicable. Frame and Deflector only. Listings and approvals apply to color (Special Order). N/A: Not Available TABLE A LABORATORY LISTINGS AND APPROVALS 2.8 AND 4.2 K-FACTOR SPRINKLERS Page 5 of 10 Page 6 of 10 TFPI7I SPRINKLER FINISH (See Note 8) K TYPE TEMP. BULB NATURAL I CHROME WHITE* LEAD BRASS PLATED ILIQUID POLYESTER COATED 135F/57°C Orange PENDENT (TY3231) and 1,2,3,4,5,6,7 1,2,3,5 155FI68°C Red 175°F/79°C Yellow UPRIGHT 200°F/93C Green 5.6 (1Y3131) 286F/141°C Blue 1/2' NPT 135F/57°C Orange RECESSED PENDENT (TY3231)* 1, 2, 4, 5 N/A 155°F/68°C Red 175°F/79°C Yellow Figure 10 200°F/93°C Green 135°F/57°C Orange RECESSED PENDENT (TY3231)** 1,2,3,4,5 N/A 155°F/68°C Red 175°F/79°C Yellow Figure 11 200°F/93°C Green 135°F/57C Orange PENDENT (TY4231) and UPRIGHT 1,2, 3,4,5, 6,7 1,2,5 155°F/68°C Red 175°F/79°C Yellow 200°F/93°C Green 8.0 (TY4131) 286F/141°C Blue 3/4,, NPT 135F/57°C Green RECESSED PENDENT (TY4231)* 1, 2, 4, 5 N/A 155°F/68°C Orange 175F/79°C Red Figure 12 200F/93°C Yellow 135F/57°C Orange RECESSED PENDENT (TY4231)** 1,2, 3,4, 5 N/A 155°F/68C Red 175°F/79°C Yellow Figure 13 200°F/93°C Green 135°F/57C Orange 8.0 1/2" NPT PENDENT (TY4931) and UPRIGHT 1,2,4, 5,6 1,2,5 155°F/68°C Red 175°F/79°C Yellow 200F/93°C Green (TY4831) 286°F/141°C Blue NOTES: Listed by Underwriters Laboratories, Inc. (UL) as Quick Response Sprinklers. Listed by Underwriters Laboratories, Inc. for use in Canada (C-UL) as Quick Response Sprinklers. Approved by Factory Mutual Research Corporation (FM) as Quick Response Sprinklers. Approved by the Loss Prevention Certification Board (LPCB Ref. No. 007k/04) as Quick Response Sprinklers; however, the LPCB does not rate the thermal sensitivity of recessed sprinklers. Approved by the City of New York under MEA 354-01-E. VdS Approved (For details contact Tyco Fire & Building Products, Enschede, Netherlands, Tel. 31-53-428-4444/Fax 31-53-428-3377). Approved by the Loss Prevention Certification Board (LPCB Ref. No. 094a/06) as Quick Response Sprinklers. Where Polyester Coated and Lead Coated Sprinklers are noted to be UL and C-UL Listed, the sprinklers are UL and C-UL Listed as Corrosion Resistant Sprinklers. Where Lead Coated Sprinklers are noted to be FM Approved, the sprinklers are FM Approved as a Corrosion Resistant Sprinklers. * Installed with Style 10 (1/2" NPT) or Style 40 (3/4' NPT) 3/4" Total Adjustment Recessed Escutcheon, as applicable. ** Installed with Style 20 (1/2" NPT) or Style 30 (3/4" NPT) 1/2" Total Adjustment Recessed Escutcheon, as applicable. Frame and Deflector only. Listings and approvals apply to color (Special Order). N/A: Not Available TABLE B LABORATORY LISTINGS AND APPROVALS 5.6 AND 8.0 K-FACTOR SPRINKLERS TFPI7I Page 7 of 10 SPRINKLER FINISH K TYPE NATURAL CHROME WHITE LEAD BRASS PLATED I POLYESTER I COATED PENDENT (TY3231) and 2.8 UPRIGHT (TY3131) 175 PSI (12,1 BAR) N/A 1/2' RECESSED PENDENT NPT (TY323) PENDENT (TY4231) and 4.2 UPRIGHT (TY4131) 175 PSI (12,1 BAR) N/A RECESSED PENDENT NPT (TY4231) PENDENT (TY3231) and 250 PSI (17,2 BAR) 175 PSI (12,1 BAR) 5.6 UPRIGHT (TY3131) OR 1/2" 175 PSI (12,1 BAR) RECESSED PENDENT NPT (TY3231) (SEE NOTE 1) N/A PENDENT (TY4231) and 175 PSI (12,1 BAR) 175 PSI (12,1 BAR) 8.0 UPRIGHT (TY4131) RECESSED PENDENT NPT TY4231) N/A 80 PENDENT (TY4931) 1/2" and 175 PSI (12,1 BAR) 175 PSI (12,1 BAR) NPT UPRIGHT (TY4831) NOTES: 1. The maximum working pressure of 250 psi (17,2 bar) only applies to the Listing by Underwriters Laboratories Inc. (UL); the Listing by Underwriters Laboratories, Inc. for use in Canada (C-UL); and , the Approval by the City of New York. TABLE C, MAXIMUM WORKING PRESSURE Installation The Series TY-FRB Sprinklers must be installed in accordance with the fol- lowing instructions: NOTES Do not install any bulb type sprinkler if the bulb is cracked or there is a loss of liquid from the bulb. With the sprinkler held horizontally, a small air bubble should be present. The diameter of the air bubble is approximately 1/16 inch (1,6 mm) for the 135"F/57"C to 3/32 inch (2,4 mm) for the 286"F/141°C temperature ratings. A leak tight 1/2 inch NPT sprinkler joint should be obtained with a torque of 7 to 14 ft.lbs. (9,5 to 19,0 Nm). A maxi- mum of 21 ft. lbs. (28,5 Nm) of torque may be used to install sprinklers with 1/2 NPT connections. A leak tight 3/4 inch NPT sprinkler joint should be ob- tained with a torque of 10 to 20 ft.lbs. (13,4 to 26,8 Nm). A maximum of 30 ft.lbs. (40,7 Nm) of torque is to be used to install sprinklers with 3/4 NPT con- nections. Higher levels of torque may distort the sprinkler inlet and cause leakage or impairment of the sprinkler. Do not attempt to make-up for insuffi- cient adjustment in the escutcheon plate by under- or over-tightening the sprinkler. Readjust the position of the sprinkler fitting to suit. The Series TY-FRB Pendent and Up- right Sprinklers must be installed in accordance with the following instruc- tions. Step 1. Pendent sprinklers are to be installed in the pendent position, and upright sprinklers are to be installed in the upright position. Step 2. With pipe thread sealant ap- plied to the pipe threads, hand tighten the sprinkler into the sprinkler fitting. Step 3. Tighten the sprinkler into the sprinkler fitting using only the W-Type 6 Sprinkler Wrench (Ref. Figure 14). With reference to Figures 1, 2, 3, 4, and 5, the W-Type 6 Sprinkler Wrench is to be applied to the sprinkler wrench flats. The Series TY-FRB Recessed Pen- dent Sprinklers must be installed in accordance with the following instruc- tions. Step A. After installing the Style 10. 20, 30, or 40 Mounting Plate, as appli- cable, over the sprinkler threads and with pipe thread sealant applied to the pipe threads, hand tighten the sprin- kler into the sprinkler fitting. Step B. Tighten the sprinkler into the sprinkler fitting using only the W-Type 7 Recessed Sprinkler Wrench (Ref. Figure 15). With reference to Figure 1, 2, 3, and 4, the W-Type 7 Recessed Page 8 of 10 2-7/8 DIA. (73,0 mm) 3/4" (19,1 mm) 2-1/4" DIA. 1/4(6,4 mm) (57,2 mm) 7-1 MOUNTING - DI A= 1/8" (3,2 mm) $ I 1-5/16" (33,3 mm)1 13/16(20,6 mm) FIGURE 6 SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT STYLE 10 RECESSED ESCUTCHEON 2.8 K-FACTOR, 1/2 INCH NPT - 2-7/8' DIA. 5/8±1/4' (73,0 mm) 3/4(19,1 mm) (15,9±6,4 mm) 2-1/4" DIA. I 1/4" (6,4 mm) I FACE OF mm MOUNTING SPRINKLER PLATE I FITTING " 1 (3,1/82 mm) [ -__ MOUNTING SURFACE CLOSURE SERIES 1-1/4" (31,8 mm)t TY-FRB 3/4"(19,1 mm) FIGURE 8 SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT STYLE 10 RECESSED ESCUTCHEON 4.2 K-FACTOR, 1/2 INCH NPT TFPI7I - 2-7/8" DIA. - 1/2±1/8" (73,0 mm) 1/2(12,7mm) E (12,7±3,2 mm) 2-1/4" DIA. 1/4" (6,4 mm) I FACE OF MOUNTING I SPRINKLER PLATE I I FITTING I l 1/8" - (3,2 mm) I MOUNTING / I \ Il I SURFACE I16,, (33,3 mm) [ CLOSURE SERIES TY-FRB 1-1/16' (27,0 mm) FIGURE 7 SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 20 RECESSED ESCUTCHEON 2.8 K-FACTOR, 1/2 INCH NPT - 2-7/8" DIA. 1/2±1/8" (73,0 mm) I 1/2" (12,7 mm) E (12,7±3,2 mm) 2-1/4" DIA. 1/4" (6,4 mm) I FACE OF (572 mm) MOUNTING SPRINKLER PLATE FITTING 1/8" _ _ jt (32 mm) MOUNTING 1: SURFACE SERIES 1-1/4" (31,8 mm) CLOSURE TY.FRB 1" (25,4 mm) FIGURE 9 SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 20 RECESSED ESCUTCHEON 4.2 K-FACTOR, 1/2 INCH NPT 5/8±1/4" (15,9±6,4 mm) FACE OF SPRINKLER FITTING MOUNTING SURFACE CLOSURE SERIES TY-FRB Sprinkler Wrench is to be applied to the sprinkler wrench flats. Step C. After the ceiling has been in- stalled or the finish coat has been ap- plied, slide on the Style 10, 20, 30, or 40 Closure over the Series TY-FRB Sprinkler and push the Closure over the Mounting Plate until its flange comes in contact with the ceiling. Care and Maintenance The Series TY-FRB Sprinklers must be maintained and serviced in accord- ance with the following instructions: NOTES Before closing a fire protection system main control valve for maintenance work on the fire protection system that it controls, permission to shutdown the affected fire protection system must be obtained from the proper authorities and all personnel who may be affected by this action must be notified. The owner must assure that the sprin- klers are not used for hanging of any objects; otherwise, non-operation in the event of a fire or inadvertent opera- tion may result. Absence of an escutcheon, which is used to cover a clearance hole, may delay the time to sprinkler operation in a fire situation. Sprinklers that are found to be leaking or exhibiting visible signs of corrosion must be replaced. Automatic sprinklers must never be painted, plated, coated or otherwise altered after leaving the factory. Modi- fied sprinklers must be replaced. Sprinklers that have been exposed to corrosive products of combustion, but have not operated, should be replaced if they cannot be completely cleaned by wiping the sprinkler with a cloth or by brushing it with a soft bristle brush. Care must be exercised to avoid dam- age to the sprinklers - before, during, and after installation. Sprinklers dam- aged by dropping, striking, wrench twist/slippage, or the like, must be re- placed. Also, replace any sprinkler that has a cracked bulb or that has lost liquid from its bulb. (Ref. Installation Section). Frequent visual inspections are rec- ommended to be initially performed for corrosion resistant coated sprinklers, after the installation has been com- TFPI7I - 2-7/8" DIA. , 5/8±114 I (730 mm) 3/4"(19,1 mm) ' - (15,9±6,4 mm) 2-1/4" DIA. I 1/4" (6,4 mm) I I FACE OF L_57'2 mm) MOUNTING SPRINKLER PLATE FITTING 1/8" I (3,2 mm) /L MOUNTING SURFACE SERIES 4 1-1/4' (31,8 mm) CLOSURE TY.FRB 3/4(19,1 mm) FIGURE 10 SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT STYLE 10 RECESSED ESCUTCHEON 5.6 K-FACTOR, 1/2 INCH NPT - 2-7/8" DIA. - 518±1/4" (73,0 mm) 3/4(19,1 mm) (15,9±6,4 mm) 2-1/4' DIA. 1/4"(6,4 mm) I PLATE SPRINKLER FACE OF (57,2 mm) MOUNTING FITTING 1/8" _ ___________ (3,2 mm) //f_ MOUNTING SURFACE CLOSURE SERIES 1-5/16"(33,3 mm) TY.FRB 13/16" (20,6 mm) FIGURE 12 SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT STYLE 40 RECESSED ESCUTCHEON 8.0 K-FACTOR, 3/4 INCH NPT Page 9 of 10 - 2-7/8" DIA. (73,0 mm) 1/2±1/8" 1/2(12,7mm) r (12,7±3,2 mm) 2-1/4" DIA. 1/4(6,4mm) I I I FACE OF [57.2mm) MOUNTING SPRINKLER PLATE I FITTING 1/8" I (3 2 mm) I f \ MOUNTING SURFACE SERIES 1-1/4"(31,8 mm) CLOSURE TYFRB 1"(25,4 mm) FIGURE 11 SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 20 RECESSED ESCUTCHEON 5.6 K-FACTOR, 1/2 INCH NPT 2-7/8' DIA. 112±118' (73,0 mm) I 1/2"(12,7 mm) I E (12,7±3,2 mm) - 2-1/4' DIA. 1/4"(6,4 mm) I FACE OF PLATE I SPRINKLER - 17_(57,2 mm) MOUNTING < 1/8" FITTING _ (3,2 mm) t \ MOUNTING t SURFACE/ CLOSURE SERIESSERIES 1-5/16"(33,3 mm)I TY-FRB 1-1/16"(27,0 mm) FIGURE 13 SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 30 RECESSED ESCUTCHEON 8.0 K-FACTOR, 3/4 INCH NPT pleted, to verify the integrity of the cor- rosion resistant coating. Thereafter, annual inspections per NFPA 25 should suffice; however, instead of in- specting from the floor level, a random sampling of close-up visual inspec- tions should be made, so as to better determine the exact sprinkler condi- tion and the long term integrity of the corrosion resistant coating, as it may be affected by the corrosive conditions present. The owner is responsible for the in- spection, testing, and maintenance of their fire protection system and de- vices in compliance with this docu- ment, as well as with the applicable standards of the National Fire Protec- tion Association (e.g., NFPA 25), in addition to the standards of any other authorities having jurisdiction. The in- stalling contractor or sprinkler manu- WRENCH RECESS (END "A" USED FOR 1/2" NPT MODELS) WRENCH RECESS (END "B" USED FOR 3/4" NPT MODELS) FIGURE 14 W-TYPE 6 SPRINKLER WRENCH facturer should be contacted relative to any questions. It is recommended that automatic sprinkler systems be inspected, tested, and maintained by a qualified WRENCH RECESS PUSH WRENCH IN TO ENSURE ENGAGEMENT WITH SPRINKLER WRENCHING AREA FIGURE 15 W-TYPE 7 RECESSED SPRINKLER WRENCH Inspection Service in accordance with local requirements and/or national codes. Page 100110 TFPI7I P/N 57-XXX-X-XXX I L MODEL/SIN 330 2.8K UPRIGHT (1/2"NPT) TY1131 331 2.SK PENDENT (1/2"NPT) TY1231 340 4.2K UPRIGHT (1/2"NPT) TY2131 341 4.2K PENDENT (1/2"NPT) TY2231 370 5.6K UPRIGHT (1/2'NPT) TY3131 371 5.6K PENDENT (1/2"NPT) TY3231 390 8.OK UPRIGHT (3/4'NPT) TY4131 391 8.OK PENDENT (3/4"NPT) TY4231 360 8.OKUP RIGHT (1/2"NPT) TY4831* 361 8.OK PENDENT (1/2'NPT) TY4931* I L 135 SPRINKLER 155 175 200 286 RATING 1 NATURAL BRASS 155*F/68*C 4 WHITE POLYESTER 175*F/79*C 3 WHITE (RAL9010)* 200°F/93°C 9 CHROME PLATED 286*F/141*C 7 LEAD COATED * Eastern Hemisphere sales only. TABLED PART NUMBER SELECTION SERIES TY-FRB PENDENT AND UPRIGHT SPRINKLERS Limited Warranty Products manufactured by Tyco Fire & Building Products (TFBP) are war- ranted solely to the original Buyer for ten (10) years against defects in mate- rial and workmanship when paid for and properly installed and maintained unde,r normal use and service. This warranty will expire ten (10) years from date of shipment by TFBP. No warranty is given for products or com- ponents manufactured by companies not affiliated by ownership with TFBP or for products and components which have been subject to misuse, improper installation, corrosion, or which have not been installed, maintained, modi- fied or repaired in accordance with ap- plicable Standards of the National Fire Protection Association, and/or the standards of any other Authorities Having Jurisdiction. Materials found by TFBP to be defective shall be either repaired or replaced, at TFBP's sole option. TFBP neither assumes, nor authorizes any person to assume for it, any other obligation in connection with the sale of products or parts of prod- ucts. TFBP shall not be responsible for sprinkler system design errors or inac- curate or incomplete information sup- plied by Buyer or Buyer's repre- sentatives. In no event shall TFBP be liable, in contract, tort, strict liability or under any other legal theory, for incidental, indirect, special or consequential dam- ages, including but not limited to labor charges, regardless of whether TFBP was informed about the possibility of such damages, and in no event shall TFBP's liability exceed an amount equal to the sales price. of any and all other warranties. ex- press or implied, including warranties of merchantability and fitness for a par- ticular purpose. This limited warranty sets forth the ex- clusive remedy for claims based on failure of or defect in products, materi- als or components, whether the claim is made in contract, tort, strict liability or any other legal theory. This warranty will apply to the full ex- tent permitted by law. The invalidity, in whole or part, of any portion of this warranty will not affect the remainder. Ordering Procedure When placing an order, indicate the full product name. Refer to the Price List for complete listing of Part Num- bers. Contact your local distributor for avail- ability. Sprinkler Assemblies with NPT Thread Connections: Specify: (Specify Model/SIN), Quick Response, (specify K-factor), (specify temperature rating), Series TY-FRB (specify Pendent or Upright) Sprinkler with (specify type of finish or coating), P/N (specify from Table D). Recessed Escutcheon: Specify: Style (10, 20, 30, or 40) Re- cessed Escutcheon with (specify*) fin- ish, P/N (specify*). * Refer to Technical Data Sheet TFP770. Sprinkler Wrench: Specify: W-Type 6 Sprinkler Wrench, P/N 56-000-6-387. Specify: W-Type 7 Sprinkler Wrench, P/N 56-850-4-001. TYCO FIRE & BUILDING PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446 tqG0 /Fire & Building / Products Technical Services: Tel: (800) 381-9312/ Fax: (800) 791-5500 Series RFII - 56 K-factor "Royal Flush II" Pendent Concealed Sprinklers Quick & Standard Response, Standard Coverage General Description The Series RFII Quick Response (3 mm bulb) & Standard Response (5 mm bulb), 5.6 K-Factor, "Royal Flush II" Concealed Pendent Sprinklers are decorative sprinklers featuring a flat cover plate designed to conceal the sprinkler. It is the best choice for archi- tecturally sensitive areas such as hotel lobbies, office buildings, churches, and restaurants. Each unit includes a Cover Plate As- sembly that conceals the sprinkler op- erating components above the ceiling. The separable two-piece design of the Cover Plate and Support Cup Assem- blies allows installation of the sprin- klers and pressure testing of the fire protection system prior to installation of a suspended ceiling or application of the finish coating to a fixed ceiling. They also permit removal of sus- pended ceiling panels for access to building service equipment without having to first shut down the fire pro- tection system and remove sprinklers. Also, the separable two-piece design of the the Sprinkler provides for 1/2 inch (12,7 mm) of vertical adjustment, to reduce the accuracy to which the length of fixed pipe drops to the sprin- klers must be cut. The Series RFII Sprinklers are shipped with a Disposable Protective IMPORTANT Always refer to Technical Data Sheet TFP 700 for the "INSTALLER WARNING" that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and in- stallation can permanently damage a sprinkler system or its compo- nents and cause the sprinkler to fail to operate in a fire situation or cause it to operate prematurely. Page 1 of 4 Cap. The Protective Cap is temporarily removed for installation, and then it can be replaced to help protect the sprinkler while the ceiling is being in- stalled or finished. The tip of the Pro- tective Cap can also be used to mark the center of the ceiling hole into plas- ter board, ceiling tiles, etc. by gently pushing the ceiling product against the Protective Cap. When the ceiling in- stallation is complete the Protective Cap is removed and the Cover Plate Assembly installed. As an option, the Series RFII Standard Response (5 mm bulb) "Royal Flush II" Concealed Pendent Sprinklers may be fitted with a silicone Air and Dust Seal (Ref. Fig. 5). The Air and Dust Seal is intended for sensitive areas where it is desirable to stop air and dust travel through the cover plate from the area above the ceiling. WARNINGS The Series RFII Concealed Pendent Sprinklers described herein must be installed and maintained in compli- ance with this document, as well as with the applicable standards of the National Fire Protection Association, in addition to the standards of any other authorities having jurisdiction. Failure to do so may impair the per- formance of these devices. The owner is responsible for maintain- ing their fire protection system and de- vices in proper operating condition. The installing contractor or sprinkler manufacturer should be contacted with any questions. Model/Sprinkler Identification Numbers TY3551 (5mm bulb) & TY3531 (3 mm bulb): maximum 175 psi (12,1 bar) by UL, C-UL, FM, LPCB and NYC. TY3504 (5 mm bulb) & TY3505 (3 mm bulb): maximum 250 psi (17,3 bar) by JULY, 2004 UL, C-UL, and NYC. Maximum 175 psi (12,1 bar) by FM. Technical Data Approvals for Series RFII UL and C-UL Listed. FM Approved. NYC under MEA 353-01-E. LPCB (Ref. No. 094a109 for TY3551 & 094a/1 0 for TY3531) Approved. The approvals apply only to the serv- ice conditions indicated in the Design Criteria section and maximum pres- sure ratings indicated in the Model/Sprinkler Identification Num- bers section. Approvals for Air & Dust Seal (Part #10908100) UL and C-UL Listed for use with the RFII (TY3551 & TY3504) Standard Re- sponse Concealed Sprinkler. Temperature Ratings 155F/68C Sprinkler - 135F/57C Plate 200F/93C Sprinkler - 165F/74C Plate Discharge Coefiient K = 5.6 GPM/psi ' (80,6 LPM/bar1"2) Adjustment 1/2 inch (12,7 mm) Finishes Cover Plate: Chrome Plated, Brass Plated, or White Painted (Custom paint matches and colors other than white are available on request.) TFPISI Page 2 of 4 TFPI8I 1/2' NPT EALING SEMBLY FRAME CAP SUPPORT CUP WITH -.-----v K BULB ROLLFORMED THREADS PRESSION -CREW GUIDE PINS (2) FLECTOR (DROPPED DEFLECTOR POSITION) lIIj_- SPRINKLER/SUPPORT CUP I ASSEMBLY THREAD INTO RETAINER SUPPORTCIJP WITHTHREAD UNTIL MOUNTING 0 - DIMPLES SURFACE IS FLUSH WITH EJECTION CEILING SPRING SOLDER' I COVER TABS (3) COVER PLATE/RETAINER PLATE ASSEMBLY FIGURE 1 SERIES RFII CONCEALED SPRINKLER ASSEMBLY Physical Characteristics Frame .............Bronze Support Cup . Chrome Plated Steel Guide Pins ......Stainless Steel Deflector ...........Bronze Compression Screw ......Brass Bulb ...............Glass Cap ........Bronze or Copper Sealing Assembly .......... Beryllium Nickel w/Teflon* Cover Plate ...........Brass Retainer ............Brass Ejection Spring . . . . Stainless Steel Patents U.S.A. 4,014,388 Operation When exposed to heat from a fire, the Cover Plate, which is normally sol- dered to the Retainer at three points, falls away to expose the Sprinkler As- sembly. At this point the Deflector sup- ported by the Guide Pins drops down to its operational position. The glass Bulb contains a fluid that expands when exposed to heat. When the rated temperature is reached, the fluid expands sufficiently to shatter the glass Bulb, activating the sprinkler and allowing water to flow. Design Criteria The RFII (TY3551 & TY3504), 5 mm Bulb Type, Concealed Pendent Sprin- klers are UL and C-UL Listed as stand- ard response - standard spray sprin- klers for use in accordance with the current NFPA standard. They are FM Approved as standard response - standard spray sprinklers for use in accordance with the current FM Loss Prevention Data Sheets. The RFII (TY3531 & TY3505) 3 mm Bulb Type, Concealed Pendent Sprin- klers are UL and C-UL Listed as quick response - standard spray sprinklers for use in accordance with the current NFPA standard. They are FM Ap- proved as standard response - stand- ard spray sprinklers for use in accord- ance with the current FM Loss Prevention Data Sheets. The Series RFII Concealed Pendent Sprinklers are only listed and ap- proved with the Series RFII Concealed Cover Plates having a metallic or white painted finish. The Series RFII must not be used in applications where the air pressure above the ceiling is greater than that below. Down drafts through the Sup- port Cup could delay sprinkler opera- tion in a fire situation. Installation The Series RFII must be installed in accordance with the following instruc- tions: NOTES Do not install any bulb type sprinkler if the bulb is cracked or there is a loss of liquid from the bulb. With the sprinkler held horizontally, a small air bubble should be present. The diameter of the air bubble is approximately 1/16 inch (1,6 mm) for the 1550F/68°C and 3/32 inch (2,4 mm) for the 200°F/930C tem- perature ratings. A leak tight 1/2 inch NPT sprinkler joint should be obtained with a torque of 7 to 14 ft.lbs. (9,5 to 19,0 Nm). A maxi- mum of 21 ft.lbs. (28,5Nm) of torque is to be used to install sprinklers. Higher levels of torque may distort the sprinkler inlet with consequent leak- age or impairment of the sprinkler. Do not attempt to compensate for in- sufficient adjustment in the Sprinkler Assembly by under- or over-tightening the Sprinkler/Support Cup Assembly. Readjust the position of the sprinkler fitting to suit. Step 1. The sprinkler must only be installed in the pendent position and With the centerline of the sprinkler per- pendicular to the mounting surface. Step 2. Remove the Protective Cap. Step 3. With pipe thread sealant ap- plied to the pipe threads, hand tighten the sprinkler into the sprinkler fitting. Step 4. Wrench tighten the sprinkler using only the RFII Sprinkler Wrench (Ref. Figure 3). The RFII Sprinkler Wrench is to be applied to the Sprin- kler as shown in Figure 3. Step 5. Replace the Protective Cap (Ref. Figure 4) by pushing it upwards until it bottoms out against the Support Cup. The Protective Cap helps prevent damage to the Deflector and Arms dur- ing ceiling installation and/or during application of the finish coating of the ceiling. It may also be used to locate the center of the clearance hole by gently pushing the ceiling material up against the center point of the Protec- tive Cap. NOTE As long as the Protective Cap remains in place, the system is considered to be "Out of Service". * Registered Trademark of DuPont II I I =--= V MANUFACTURER DEFLECTOR COVER PLATE PRESET GAP IN DROPPED RETAINER 3/32 (2,4 mm) POSITION ASSEMBLY COVER PLATE DIAMETER DIMENSION A 3/16' to 11/16" (4,8 to 17,5 mm) REFERENCE COVER PLATE - PROFILE DEPTH DIMENSION B TFPI8I Page 3 of 4 FACE OF SPRINKLER FITTING SPRINKLER SUPPORT CUP ASSEMBLY 1/2 (12,7 mm) THREADED D ADJUSTMENT CLEARANCE HOLE - DIAMETER DIMENSION 7Drf CLEARANCE HOLE FACE OF CEILING, RETAINING RING MOUNTING SURFACE FIGURE 4 DISPOSABLE PROTECTIVE CAP 3-1/4" (82,6 mm) C: 2-3/8' to 2-5/8 (60,3 to 66,7 mm) 3/16" (4,8 mm) D: 1-3/4" to 2-1/4" (44,5 to 57,2 mm) FIGURE 2 SERIES RFII CONCEALED SPRINKLER INSTALLATION DIMENSIONS I1IIIIII FRAME ARM ' I I SUPPORT - CUP [ 7/8' (23 mm) SQUARE ALIGN ARROWS WITH / I FRAME ARMS 1 4 ACCEPTS 1 0 [ 1/2' SOCKET DRIVE FIGURE 3 RFII SPRINKLER WRENCH Step 6. After the ceiling has been com- pleted with the 2-1/2 inch (63,5 mm) diameter clearance hole and in prepa- ration for installing the Cover Plate As- sembly, remove and discard the Pro- tective Cap, and verify that the Deflector moves up and down freely. If the Sprinkler has been damaged and the Deflector does not move up and down freely, replace the entire Sprin- kler assembly. Do not attempt to mod- ify or repair a damaged sprinkler. Step 7. When installing an Air and Dust Seal, refer to Figure 5, otherwise proceed to Step 8. To attach the Air and Dust Seal, verify the angle of the out- side edge of the seal is oriented ac- cording to Figure 5. Start the edge of the Retainer in the grooved slot of the Air and Dust Seal and continue around the retainer until the entire Air and Dust Seal is engaged. NOTE The Air and Dust Seal is only to be installed on the periphery of the Re- tainer. Step 8. Screw on the Cover Plate/Re- tainer Assembly until the Retainer - Figure 2 (or Air and Dust Seal - Figure 5) contacts with the ceiling. Do not continue to screw on the Cover Plate/Retainer Assembly such that it lifts a ceiling panel out of its normal position. If the Cover Plate/Retainer Assembly cannot be engaged with the Support Cup or the Cover Plate/Re- tainer Assembly cannot be engaged sufficiently to contact the ceiling, the Sprinkler Fitting must be repositioned. Care and Maintenance The Series RFII must be maintained and serviced in accordance with the following instructions: NOTES Absence of the Cover Plate Assembly may delay sprinkler operation in a fire situation. Page 4 of 4 TFPI8I SUPPORT SPRINKLER FACE OF ORIENT SEAL BEVEL AS SHOWN COVER PLATE RETAINER CUP CiRETAINER ASSEMBLY EPLATE CLEAN ROOM LIP OF coven SEAL FIGURE 5 OPTIONAL AIR AND DUST SEAL FOR SERIES RFII (TY3551 & TY3504) When properly installed, there is a nominal 3/32 inch (2,4 mm) air gap between the lip of the Cover Plate and the ceiling, as shown in Figure 2. This air gap is necessary for proper opera- tion of the sprinkler. If the ceiling is to be repainted after the installation of the Sprinkler, care must be exercised to ensure that the new paint does NOT seal off any of the air gap. Factory painted Cover Plates MUST NOT be repainted. They should be re- placed, if necessary, by factory painted units. Do not pull the Cover Plate relative to the Enclosure. Separation may result. Before closing a fire protection system main control valve for maintenance work on the fire protection system that it controls, permission to shutdown the affected fire protection system must be obtained from the proper authorities and all personnel who maybe affected by this action must be notified. Sprinklers that are found to be leaking or exhibiting visible signs of corrosion must be replaced. Automatic sprinklers must never be painted, plated, coated or otherwise altered after leaving the factory. Modi- fied sprinklers must be replaced. Sprinklers that have been exposed to corrosive products of combustion, but have not operated, should be replaced if they cannot be completely cleaned by wiping the sprinkler with a cloth or by brushing it with a soft bristle brush. Care must be exercised to avoid dam- age to the sprinklers - before, during, and after installation. Sprinklers dam- aged by dropping, striking, wrench twist/slippage, or the like, must be re- placed. Also, replace any sprinkler that has a cracked bulb or that has lost liquid from its bulb. (Ref. Installation Section). If a sprinkler must be removed, do not reinstall it or a replacement without reinstalling the Cover Plate Assembly. If a Cover Plate Assembly becomes dislodged during service, replace it im- mediately. The owner is responsible for the in- spection, testing, and maintenance of their fire protection system and de- vices in compliance with this docu- ment, as well as with the applicable standards of the National Fire Protec- tion Association (e.g., NFPA 25), in addition to the standards of any other authorities having jurisdiction. The in- stalling contractor or sprinkler manu- factu rer should be contacted relative to any questions. It is recommended that automatic sprinkler systems be inspected, tested, and maintained by a qualified Inspection Service in accordance with local requirements and/or national codes. Limited Warranty Products manufactured by Tyco Fire Products are warranted solely to the original Buyer for ten (10) years against defects in material and work- manship when paid for and properly installed and maintained under normal use and service. This warranty will ex- pire ten (10) years from date of ship- ment by Tyco Fire Products. No war- ranty is given for products or components manufactured by compa- nies not affiliated by ownership with Tyco Fire Products or for products and components which have been subject to misuse, improper installation, corro- sion, or which have not been installed, maintained, modified or repaired in ac- cordance with applicable Standards of the National Fire Protection Associa- tion, and/or the standards of any other Authorities Having Jurisdiction. Mate- rials found by Tyco Fire Products to be defective shall be either repaired or replaced, at Tyco Fire Products' sole option. Tyco Fire Products neither as- sumes, nor authorizes any person to assume for it, any other obligation in connection with the sale of products or parts of products. Tyco Fire Products shall not be responsible for sprinkler system design errors or inaccurate or incomplete information supplied by Buyer or Buyer's representatives. IN NO EVENT SHALL TYCO FIRE PRODUCTS BE LIABLE, IN CON- TRACT, TORT, STRICT LIABILITY OR UNDER ANY OTHER LEGAL THE- ORY, FOR INCIDENTAL, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LABOR CHARGES, RE- GARDLESS OF WHETHER TYCO FIRE PRODUCTS WAS INFORMED ABOUT THE POSSIBILITY OF SUCH DAMAGES, AND IN NO EVENT SHALL TYCO FIRE PRODUCTS' LI- ABILITY EXCEED AN AMOUNT EQUAL TO THE SALES PRICE. THE FOREGOING WARRANTY IS MADE IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESS OR IMPLIED. INCLUDING WARRANTIES OF MERCHANTABILITY AND FIT- NESS FOR A PARTICULAR PUR- POSE. Ordering Procedure When placing an order, indicate the full product name. Contact your local dis- tributor for availability. Sprinkler Assembly: Specify: (SIN), (specify temperature rating) Series RFII Concealed Pen- dent Sprinkler, P/N (specify). 155F/68C 200F/93C TY3551 51-790-1-155 51-790-1-200 1Y3504 51-796-1-155 51-796-1-200 1Y3531 51-792-1-155 51-792-1-200 TY3505 51-797-1-155 51-797-1-200 Separately Ordered Cover Plate: Specify: (specify temperature rating) Series RFII Concealed Cover Plate with (specify finish), P/N (specify). 135F/57C(a) 165F/74C(b) Brass 56-792-1-135 56-792-1-165 Bright Brass 56-792-2-135 56-792-2-165 Chrome 56-792-9-135 56-792-9-165 Brushed Chrome 56-792-8-135 56-792-8-165 White 56-792-0-135 56-792-0-165 White (RAL9010)* 56-792-3-135 56-792-3-165 Bright White 56-792-4-135 56-792-4-165 Off White 56-792-5-135 56-792-5-165 Black 56-792-6-135 56-792-6-165 Custom 56-792-X-135 56-792-X-165 For use with 155F/68C sprinklers. For use with 200F/93C sprinklers. * Eastern Hemisphere sales only. Sprinkler Wrench: Specify: RFII Sprinkler Wrench, P/N 56-000-1-075. Air and Dust Seal: Specify: Air and Dust Seal, P/N 56-908-1 -001. TYCO FIRE PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446