Loading...
HomeMy WebLinkAbout2150 PALOMAR AIRPORT RD; ; AS110064; Permit1/29/25,12:42 PM AS 110064 Permit Data City of Carlsbad Sprinkler Permit 2150 PALOMAR Job Address: AIRPORT RD Permit Type: SPRINK Parcel No: 7602218206 Lot #: 0 Reference No.: Permit No: AS110064 Status: ISSUED Applied 4/21/2011 Approved: 4/21/2011 Issued: 4/21/2011 PC #: Inspector: Project Title: RICHARD SAX T.I. FIRE SPRINKLER PLAN CHECK & INSPECTIONS Applicant: SULLY FIRE PROTECTION 1975 SPANISH OAK WAY VISTA, CA 760-727-3444 Owner: TETON JET LLC PALOMAR AIRPORT CENTER LLC 2150 PALOMAR AIRPORT RD #O-17A CARLSBAD CA Fees ($) Add'l Fees ($) Total ($) Balance ($) 130 01 130 0 about:blank 1/1 A Hoo- tqco IF/re & Building / Products Technical Services: Tel: (800) 381-9312 I Fax: (800) 791-5500 Series EC-8 — 8.0 K-factor Extended Coverage (Light Hazard) Pendent and Recessed Pendent Sprinklers General Description The Series EC-8 Extended Coverage Pendent Sprinklers are decorative glass bwo sprinklers designed for use in light hazard occupancies. They are intended for use in automatic sprinkler Systems designed Wi accordance with standard installation rules (e.g., NFPA 13) for a maximum coverage area of W ,h paru LU We maximum coverage area of 225 ft2 (20,6 m2) for standard coverage sprin- The recessed version of the EC-8, in- tended for use in areas with a finished ceiling, uses either the two-piece Style 30 or 40 Recessed Escutcheon. The Style 30 Recessed Escutcheon pro- viu up to ti iui, ,,, 11"111 UI toldl adjustment from the flush pendent po- sition, whereas, the Style 40 provides ..,,-t ment from the flush pendent position. The adjustment provided by the Re- , C .2..t_trt2r n,I:,r,z curacy to which the fixed pipe drops to the sprinklers must be cut Corrosion resistant coatings, wnere applicable, are utilized to extend the life of copper alloy sprinklers beyond that which would otherwise be ob- tained when exposed to corrosive at- mospheres. Although corrosion resis- IMPORTANT Always refer to Technical Data Sheet TFP 700 for the "INSTALLER WARNING" that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and in- stallation can permanently damage a sprinkler system or its compo- nents and cause The sprinkler to fail to operate in a fire situation or cause it to operate prematurely. Page 1 of 6 tant coated sprinklers have passed the standard corrosion tests of the appli- cable approval agencies, the testing is not representative of all possible cor- rosive atmospheres. Consequently, it is recommended that the end user be consulted with respect to the suitability of these corrosion resistant coatings for any given corrosive environment The effects of ambient temperature, concentration of chemicals, and gas/chemical velocity, should be con- sidered, as a minimum, along with the corrosive nature of the chemical to which the sprinklers will be exposed. WARNE The Series EC-8 Extended Coverage Sprinklers described herein must be irsta-il;d, and maintained in seraph- arise with This document, as well as with the applicable standards of the Natio'a' Firs Protsstis slk in addition to the standards of any other authorities having jurisdiction. F-Ikkir-In in fin en snsI imnr iha fonnance of these devices. The owner is responsible for maintain- tlt*J UfCI UI pIU t,4RfII Wilt U47- vices in proper operating condition. The installing contractor or sprinkler with any questions. Model/Sprinkler Identification Number TY4232- Pendent;80K TY4232 isa redeigation for C4232. MARCH, 2007 Technical Data PppTo'4as UL and C-UL Listed. FM and NYC Ap- proved. (Refer to Table A for complete approval information including corro- sion resistant status. The approvals apply to the service conditions indi- cated in the Desiga CUterta sectio Maximum Working Pressure 175 psi (12,1 bar) Pipe Thread Connection 3/4 inch NPT DisvbaTge Cocient K = 8.0 GPM/psi112 (115,2 LPM/bar112) TFP223 Page 2 of 6 TFP223 Components: 3/4 ** ESCUTCHEON PLATE 1 - Frame SEATING SURFACE Button Sealing Assembly NPT _____ Bulb _____ 2J/6" Compression ________ Screw (54,0 mm) 6-Deflector *1/2 TiL _____ * Temperature rating is 12,7mm) 1J116' I 6-1 indicated on Deflector.MAKE-IN (36,5mm) ** Pipe thread cormedum per ISO 7/1 can be provided on special request. FIGURE 1 SERIES EC-8 (TY4232) EXTENDED COVERAGE PENDENT SPRINKLERS SPRINKLER FINISH (See Note 4) HAZARD TYPE TEMP. BULB NATURAL CHROME WHITE* LIQUID BRASS PLATED JPOLYESTER LIGHT PENDENT 135F/57C Orange Refer to Table B for UL and C-UL _______________ 1,2,3,5 155°F/68°C Red REC. PENDENT 135F167"C Orange Sensitivity Rating and wl Style 30 Esc. 1,2,3,5 Refer to Table C for FM 155°F/68"C Red REC. PENDENT 135°F?57"C Orange Sensitivity Rating w/ Style 4OEsc. 1,2,5 155°F/68°C Red NOTES: Listed by Underwriters Laboratories, Inc. (UL). Listed by Underwriters Laboratories, Inc. for use in Canada (C-UL). Apprnved by Factory Mutual Resea"ch Corporation (FM). Where Polyester Coated Sprinklers are noted to be UL and C-UL Listed, the sprinklers are UL and C-UL Listed as Corrosion Resistant Sprinklers. Approved by the City of New York under MEA 113-04-E. Frame and Deflector only. Listings and approvals apply to color (Special Order). TABLE A LABORATORY LISTINGS AND APPROVALS (Refer to the Design Criteria Section) Temperature Ratings 135°F/57°C and 155°F/680C Finish Sprinkler: Refer to Table A Recessed Escutcheon: White Coated, Chrome Plated, and Brass Plated Physical Characteristics Frame .............Bronze Button .............Bronze Sealing Assembly .......... Beryllium Nickel w/Tefiont Bulb ........Glass (3 mm dia.) Compression Screw ......... ........Bronze Deflector ............Brass t Registered trademark of DuPont Operation The glass bulb contains a iluid Thai expands when exposed to heat. When the rated temperature is reached, the fluid expands sufficiently to shatter the glass bulb, allowing the sprinkler to activate and flow water. Design Criteria The Series EC-8 Extended Coverage Pendent Sprinklers must only be In- stalled in accordance with the applica- ble UL and C-UL Listing or FM Ap- proval requirements as indicated below. Only the Style 30 or 40 Re- cessed Escutcheon is to be used for recessed installation, as applicable (Ref. Table A, B, and C).. IlL and C-UL Listing Requirements The Series EC-8 Sprinklers may be used for the coverage areas shown in Table D, based on maintaining the minimum specified flow rate as a function of coverage area and haz- ard group for all of the sprinklers in the design area. With respect to heat sensitivity, the Series EC-8 Sprinklers can be used With unobstructed construction con- sisting of flat, smooth ceilings (in- cluding bar joists) with a maximum pitch of one in six as defined and permitted by NFPA 13. . The n mm'i spats be- TFP223 135°F 155°F AREA STYLE 16x16 Pendent OR OR 16x16 Style 30Recessed OR OR 16x16 Style 40 Recessed OR QR - 18x18 Pendent QR OR 18 x. iS Style 30 Recessed OR SR. 1808 18 Style 40 Recessed OR SR 20 x 20 Pendent OR SR 20 x 20 Style 30 Recessed OR SR 20 x 20 Style 40 Recessed SR SR OR: Quick Response SR: Standard Response N/A: Not Applicable TABLE B SENSITIVI-TY RATIND FOR. UL AND C-UL LISTING- OF SERIES EC-8 SPRINKLERS 135F- 155F- AREA STYLE 16x16 Pendent OR QR 16 x 16 Style 30 Recessed OR N/A 16 x 16 Style 40 Recessed N/A N/A 18x18 Pendent QR OR 18 x 18 Style 30 Recessed QR N/A 18 x 18 Style 30 Recessed N/A N/A 20x20 Pendent OR OR 20 x 20 Style 30 Recessed OR N/A 20 x 20 Style 40 Recessed N/A N/A OR: Quick Response SR: Standard Response-- N/A: Not Applicable TABLE C SENSITIVITY RATING FOR FM APPROVAL OF SERIES i EC-8 SPRINKLERS Page 3 of 6 Installation The Series EC-8 Sprinklers must be installed in accordance with the follow- ing instructions: NOTES Do not install any bulb type sprinkler if the Iii/b is cracked or there ,s a loss of liquid from the bulb. With the sprinkler held horizontally, a small air bubble should be present. The diameter of the air bubble is approximately 1/16 inch (1,6mm). A leak tight 3/4 inch NPTsprinkler joint should be obtained with a torque of 10 to 20 ft.lbs. (13)4 to-26,8 Nm-i A maxi- mum of 30 tUbs. (40,7 Nm) of torque is to be used to install sprinklers. Higher levels of torque may distort the sprinkler iri/et wft/r consequent leak- age or impairment of the sprinkler. Do-not attempt - to-compensate- for-in- sufficient adjustment of an Escutcheon Plate by under- or over-tightening the Sprinkler. Readjust the position of the sprinkler fitting to suit. Step 1. The sprinkler must be installed with the deflector parallétto the mount- ing surface. Pendent sprinklers must be installed in the pendent position. Step 2. After installing the Style 30 or 40 mounting plate (or other escutch- eon, as applicable), over the sprinkler pipe threads, and with pipe Thread sealant applied to the pipe threads, hand tighten the sprinkler into the sprinkler fitting. Step 3. Wrench tighten pendent sprin- klers-using only-the W-Type 3- (End -A) - Sprinkler Wrench. Wrench tighten the recessed pendent sprinklers using only the W-Type 23 Sprinkler Wrench. The wrench recess of the applicable sprinkler wrench (Ref. Figure 4 and 5) is to be applied to the sprinkler wrench flats tRei. Figure f). tween the Series EC-8 Sprinklers, to prevent cold soldering, is 8 feet (2,4 M). 4. The Series EC-8 Sprinklers are to be installed in accordance with all other requirements of NFPA 13 for ex- tended coverage pendant sprin- klers. FM Approval Requirements The Series EC-8 Extended Coverage Sprinklers aretabe installed in accord-. ance with the applicable Factory Mu- tual Loss Prevention Data Sheet. Infor- mation provided in the FM Loss Prevention Data Sheets relate to, but are not limited to, hydraulic design, ceiling slope and obstructions, mini- mum and maximum atlawabte spec- ing, and deflector-to ceiling distance. Page 4 of 6 TFP223 DESCRIPTION AREA GPM PSI TY4232 (K=8.0) PENDENT 16 x 16 26 10.6 18x18 20 x 20 5.O 1 ft. = 0.3048 m 1 ft2 = 0.093 m2 I gpm=3.785 1pm 1 psi = 0.06895 bar I gpm/ft2 = 40.74 mm/mm TABLED FLOW-CRITERIA-FOR-UL AND C1JL LISTING OF SERIES EC-8 SPRINKLERS 2-7/8 DIA. 1/2±1/8 (73,0 mm) 1/2' (12,7 mm) r (12,7t3,2 mm) 2-AW DIA. 1/4" (6,4 mm) FACE OF (57,2 mm) FITTING (3,2 mm) SPRINKLER 1/8" / MOUNTING / SURFACE /7 MOUNTING CLOSURE ________ PLATE 1-1I4"(31,8mm) 1" (25,4 mm) FIGURE 2 SERIES EC-8 RECESSED PENDENT SPRINKLER ASSEMBLY WITH iWO-PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 30 RECESSED ESCUTCHEON • 2-7/8" DIA. 9/16±1/4" (73,0 mm) 3/4"(19,1 mm) (14,3±6,4 mm) 2-114" DIA. 114(6,4 mm) FACE OF (57,2 mm) SPRINKLER 1/8" FITTING (3,2 mm) T \ MOUNTING / SURFACE MOUNTING PLATE CLOSURE I 1-5/16(33,3 mm) 1 13/16(20,6mm) FIGURE 3 SERIES EC-8 RECESSED PENDENT SPRINKLER ASSEMBLY WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT STYLE 40 RECESSED ESCUTCHEON "FITTING SIDE" TOWARDS SPRINKLER FITTING / WRENCH RECESS (END "A") FIGURE 4 W-TYPE 3 SPRINKLER WRENCH., WRENCH RECESS '----I FIGURE 5 W-TYPE 23 RECESSED SPRINKLER WRENCH Care and Maintenance The Series EC-8 Sprinklers must be maintained and serviced in accord- ance with the following instructions: NOTE Before closing a fire protection system main control valve for maintenance work on the fire protection system that it controls, permission to shut down the affected fire protection systems must be obtained from the proper authorities and all personnel who may be affected by ffiis act/on must be no- tified. Sprinklers that are found to be leaking or exhibiting visible signs of corrosion must be replaced. Automatic sprinklers must never be painted, plated, coated, or otherwise altered after leaving the factory. Modi- fied sprinklers must be replaced. Sprinklers that have been exposed to TFP223 Page 5 of 6 corrosive products of combustion, but have not operated, should be replaced if they cannot be completely cleaned by wiping the sprinkler with a cloth or by brushing it with a soft bristle brush. Care must be exercised to avoid dam- age to the sprinklers - before, during, and after installation. Sprinklers dam- aged by dropping, striking, wrench twist/slippage, or the like, must be re- placed. Also, replace any sprinkler that has a cracked bulb or that has lost liquid from its bulb. (Ref. Installation Section). Frequent visual inspections are rec- ommended to be initially performed for corrosion resistant coated sprinklers, after the installation has been com- pleted, to verify the integrity of the cor- rosion resistant coating. Thereafter, snni*l insnetinnq mar NFPA 21, should suffice; however, instead of in- specting from the floor level, a random sampling of close-up visual inspec- tions should be made, so as to better determine the exact sprinkler condi- tion and the long term integrity of the corrosion resistant coating, as it may be affected by the corrosive conditions present. The owner is responsible for the in- spection, testing, and maintenance of their fire protection system and de- vices in compliance with this docu- ment, as well as with the applicable standards of the National Fire Protec- tion Association (e.g., NFPA 25), in addition to the standards of any other authorities having jurisdiction. The in- stalling contractor or sprinkler manu- facturer should be contacted relative to any questions. It is recommended that automatic sprinkler systems be inspected, tested, and maintained by a qualified Inspection Service in accordance with local requirements and/or national codes. Limited Warranty Products manufactured by Tyco Fire & Building Products (TFBP) are war- ranted solely to the original Buyer for ten (10) years against defects in mate- rial and workmanship when paid for and properly installed and maintained under normal use and service. This warranty will expire ten (10) years from date of shipment by TFBP. No warranty is given for products or com- ponents manufactured by companies not affiliated by ownership with TFBP or for products and components which have been subject to misuse, improper installation, corrosion, or which have not been installed, maintained, modi- fied or reeaired in accordance with a- plicable Standards of the National Fire Protection Association, and/or the standards of any other Authorities Having Jurisdiction. Materials found by TFBP to be defective shall be either repaired or replaced, at TFBP's sole option. TFBP neither assumes, nor authorizes any person to assume for it, any other obligation in connection with the sate of products or parts of prod- ucts. TFBP shall not be responsible for sprinkler system design errors or inac- curate or incomplete information sup- plied by Buyer or Buyer's repre- sentatives. In no event shall TFBP be liable, in contract, tort, strict liability or under any other legal theory, for incidental, indirect, special or consequential dam- ages, including but not limited to labor charges, regardless of whether TFBP was informed about the possibility of such damages, and in no event shall TFBP's liability exceed an amount equal to the sales price. The foregoing warranty is made in lieu of any and all other warranties, ex- press or implied, including warranties of merchantability and fitness for a par- ticular purpose. This limited warranty sets forth the ex- clusive remedy for claims based on failure of or defect in products, materi- als or components, whether the claim is made in contract, tort, strict liability or any other legal theory. This warranty will apply to the full ex- tent permitted by law. The invalidity, in whole or part, of any portion of this warranty will not affect the remainder. Ordering Procedure When placing an order, indicate the fult product name. Please spectf'j the Sprinkler Identification Number (SIN), quantity, and temperature rating. Re- fer to the Price List for complete listing of Part Numbers. Contact your local distributor for avail- ability. Sprinkler Assemblies with NPT Thread Connections Specify: TY4232, (specify tempera- ture rating), Extended Coverage Pen- dent Sprinkler with (specify finish). PII'4 (specify)- 137w ron .ju-ou I- White Coated .............PSN 50-801-4-135 White (RAL9O1O). .......... PSN 50-801-3-135 Chrome Plated . .......... .PSN 50-801-9-135 155°FI68C Natural Brass .............PSN 50-801-1-155 White Coated .............PSN 50-801-4-155 White (RAL90W) .........PSN 0.80?-3-155 Chrome Plated ............PSN 50-801-9-155 Eastern Hemisphere sales only. Recessed Escutcheon: Specify: Style (30 or 40) Recessed Escutcheon with (specify finish), PIN (specify). Style 30 Recessed Escutcheon Chrome Plated ............PSN 56-705-9-011 White Color Coated ........PSN 56-705-4-011 White (RAL901O) .........PSN 56-705-3-011 Brass Plated ......... ..... PSN 56-705-2-011 Style 40 Recessed Escutcheon Chrome Plated ............PSN 56-700-9-010 White Color Coated ........PSN 56-700-4-010 White (RAL9OIO) ........... PSN 56-700-3-010 Brass Plated ..............PSN 56-700-2-010 *Eastern Hemisphere sales only. Sprinkler Wrench: Specify: W-Type 3 Sprinkler Wrench, P/N 56-895-1-001. Specify: W-Type 23 Recessed Sprin- kler Wrench, P/N 56-000-6-838. Page 6 of 6 TFP223 TYCO FIRE & BUILDING PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446 Sully Fire Protection 1975 Spanish Oak Way Vista, California 92081 760-727-3444 HYDRAULIC CALCULATIONS FOR Suite 208 - Entire Room Room Design - Hallway door to have automatic closer Richard Sax Tenant Improvement 2150 Palomar Airport Road, Suite 208 Carlsbad, California FILE NUMBER: HangerTl.sdf April 19, 2011 -DESIGN DATA- OCCUPANCY CLASSIFICATION: Light Hazard DENSITY: AREA OF APPLICATION: COVERAGE PER SPRINKLER: NUMBER OF SPRINKLERS CALCULATED: TOTAL SPRINKLER WATER FLOW REQUIRED: FLOW AND PRESSURE REQUIRED AT SOURCE PRESSURE AVAILABLE AT SOURCE: SPRINKLER ORIFICE SIZE: 0.10 gpm/sqft 1,315 square feet 256 sqft max. 7 sprinklers 174.20 gpm 174.20 gpm @ 17.5 psi 58.7 psi at 242.9 gpm 17/32" NAME OF CONTRACTOR: Sully Fire Protection, C-16 701590 Note: Tenant improvement calculations for Suite 208 evaluated to existing light hazard occupancy requirements for other more remote light hazard occupancy requirements at base of riser. CALCULATIONS BY MASS COMPUTER PROGRAM (LICENSE # 50110279 HRS SYSTEMS, INC. ATLANTA, GA SPRINKLER SYSTEM HYDRAULIC ANALYSIS Page 2 DATE: 4/20/2011 C:\HASS78\FILES\HANGERTI.SDF JOB TITLE: Revised Office Space WATER SUPPLY DATA SOURCE STATIC RESID. FLOW AVAIL. TOTAL REQ'D NODE PRESS. PRESS. @ PRESS. @ DEMAND PRESS. TAG (PSI) (PSI) (GPM) (PSI) (GPM) (PSI) RISER 58.7 58.7 242.9 58.7 174.2 17.5 Required pressure is 41.2 psi (70%) less than available pressure. AGGREGATE FLOW ANALYSIS: TOTAL FLOW AT SOURCE 174.2 GPM TOTAL HOSE STREAM ALLOWANCE AT SOURCE 0.0 GPM OTHER HOSE STREAM ALLOWANCES 0.0 GPM TOTAL DISCHARGE FROM ACTIVE SPRINKLERS 174.2 GPM NODE ANALYSIS DATA DENSITY NODE TAG ELEVATION NODE TYPE PRESSURE DISCHARGE AREA REQ. ACT. (FT) (PSI) (GPM) (FT-2) (GPM/FT"2) 1 8.8 K= 8.00 10.2 25.6 256.0 0.100 0.100 2 8.8 K= 8.00 10.4 25.8 256.0 0.100 0.101 3 8.8 K= 8.00 10.4 25.8 256.0 0.100 0.101 4 8.8 K= 5.60 10.7 18.3 150.0 0.100 0.122 5 8.8 K= 8.00 10.6 26.0 256.0 0.100 0.102 6 8.8 K= 8.00 10.8 26.2 256.0 0.100 0.102 7 8.8 K= 8.00 10.8 26.3 256.0 0.100 0.103 A 9.4 12.3 - - - B 9.4 - - - - 12.3 - - - C 9.4 - - - - 12.4 - - - D 9.4 - - - - 12.4 - - - E 9.4 - - - - 12.4 - - - F 9.4 - - - - 12.4 - - - G 9.4 - - - - 12.5 - - - H 9.4 - - - - 12.5 - - - TOR 9.4 - - - - 13.3 - - - RISER 0.0 SOURCE 17.5 174.2 SPRINKLER SYSTEM HYDRAULIC ANALYSIS Page 3 DATE: 4/20/2011 C:\HASS78\FILES\HANGERTI.SDF JOB TITLE: Revised Office Space PIPE DATA PIPE TAG Q(GPM) DIA(IN) LENGTH PRESS. END ELEV. NOZ. PT DISC. VEL(FPS) HW(C) (FT) SUM. NODES (FT) (K) (PSI) (GPM) FL/FT (PSI) Pipe: 1 -25.6 1.087 PL 5.25 PF 2.3 1 8.8 8.0 10.2 25.6 8.9 120 FTG ET PE -0.3 A 9.4 0.0 12.3 0.0 0.173 TL 13.55 PV Pipe: 2 -25.8 1.087 PL 4.25 PF 2.2 2 8.8 8.0 10.4 25.8 8.9 120 FTG ET PE -0.3 B 9.4 0.0 12.3 0.0 0.175 TL 12.55 PV Pipe: 3 -25.8 1.087 PL 4.25 PF 2.2 3 8.8 8.0 10.4 25.8 8.9 120 FTG ET PE -0.3 D 9.4 0.0 12.4 0.0 0.176 TL 12.55 PV Pipe: 4 -18.3 1.087 PL 10.50 PF 2.0 4 8.8 5.6 10.7 18.3 6.3 120 FTG 2ET PE -0.3 E 9.4 0.0 12.4 0.0 0.093 TL 21.20 PV Pipe: 5 -26.0 1.087 PL 3.25 PF 2.1 5 8.8 8.0 10.6 26.0 9.0 120 FTG ET PE -0.3 E 9.4 0.0 12.4 0.0 0.178 TL 11.55 PV Pipe: 6 -26.2 1.087 PL 2.25 PF 1.9 6 8.8 8.0 10.8 26.2 9.1 120 FTG ET PE -0.3 F 9.4 0.0 12.4 0.0 0.181 TL 10.55 PV Pipe: 7 -26.3 1.087 PL 2.25 PF 1.9 7 8.8 8.0 10.8 26.3 9.1 120 FTG ET PE -0.3 H 9.4 0.0 12.5 0.0 0.182 TL 10.55 PV Pipe: 8 -25.6 3.314 PL 16.17 PF 0.0 A 9.4 0.0 12.3 0.0 1.0 120 FTG ---- PE 0.0 B 9.4 0.0 12.3 0.0 0.001 TL 16.17 PV Pipe: 9 -51.4 3.314 PL 2.17 PF 0.1 B 9.4 0.0 12.3 0.0 1.9 120 FTG T PE 0.0 C 9.4 0.0 12.4 0.0 0.003 TL 21.87 PV Pipe: 10 25.8 3.314 PL 14.00 PF 0.0 C 9.4 0.0 12.4 0.0 1.0 120 FTG T PE 0.0 D 9.4 0.0 12.4 0.0 0.001 TL 33.70 PV Pipe: 11 -44.3 3.314 PL 16.70 PF 0.0 E 9.4 0.0 12.4 0.0 1.6 120 FTG ---- PE 0.0 F 9.4 0.0 12.4 0.0 0.002 TL 16.70 PV Pipe: 12 -70.5 3.314 PL 2.17 PF 0.1 F 9.4 0.0 12.4 0.0 2.6 120 FTG T PE 0.0 G 9.4 0.0 12.5 0.0 0.005 TL 21.87 PV SPRINKLER SYSTEM HYDRAULIC ANALYSIS Page 4 DATE: 4/20/2011 C:\HASS78\FILES\HANGERTI.SDF JOB TITLE: Revised Office Space PIPE TAG Q(GPM) DIA(IN) LENGTH PRESS. END ELEV. NOZ. PT DISC. VEL(FPS) HW(C) (FT) SUM. NODES (FT) (K) (PSI) (GPM) FL/FT (PSI) Pipe: 13 26.3 3.314 PL 14.00 PF 0.0 G 9.4 0.0 12.5 0.0 1.0 120 FTG T PE 0.0 H 9.4 0.0 12.5 0.0 0.001 TL 33.70 PV Pipe: 14 -77.2 3.314 PL 20.40 PF 0.1 C 9.4 0.0 12.4 0.0 2.9 120 FTG ---- PE 0.0 G 9.4 0.0 12.5 0.0 0.006 TL 20.40 PV Pipe: 15 -174.1 3.314 PL 15.00 PF 0.8 G 9.4 0.0 12.5 0.0 6.5 120 FTG 2E PE 0.0 TOR 9.4 0.0 13.3 0.0 0.026 TL 30.00 PV Pipe: 16 -174.2 4.310 PL 9.50 PF 0.1 TOR 9.4 0.0 13.3 0.0 3.8 120 FTG CG PE 4.1 RISER 0.0 SRCE 17.5 (N/A) 0.007 TL 9.50 PV NOTES (HASS) Calculations were performed by the HASS 8.1 computer program under license no. 50110279 granted by HRS Systems, Inc. 208 South Public Square Petersburg, TN 37144 (931) 659-9760 The system has been calculated to provide an average imbalance at each node of 0.024 gpm and a maximum imbalance at any node of 0.382 gpm. Total pressure at each node is used in balancing the system. Maximum water velocity is 9.1 ft/sec at pipe 7. PIPE FITTINGS TABLE Pipe Table Name: STANDARD.PIP SPRINKLER SYSTEM HYDRAULIC ANALYSIS Page 5 DATE: 4/20/2011 C:\HASS78\FILES\HANGERTI.SDF JOB TITLE: Revised Office Space PAGE: W MATERIAL: DyThd HWC: 120 Diameter Equivalent Fitting Lengths in Feet (in) E T L R B G A C Eli Tee 45 RunTee Bfly Gate Alarm Check 1.087 2.40 5.90 1.20 2.30 0.00 0.00 0.00 4.80 PAGE: Y MATERIAL: DynaFi HWC: 120 Diameter Equivalent Fitting Lengths in Feet (in) E T L C B G A D Eli Tee 45 Check BtrFly GateVi 3.314 7.50 19.70 0.00 0.00 0.00 0.00 0.00 0.00 4.310 9.60 22.70 0.00 0.00 0.00 0.00 0.00 0.00 WATER SUPPLY ANALYSIS Static: 58.70 psi Resid: 58.69 psi Flow: 242.9 gpm 70.0 60.0 50.0 P R F: S 40.0 S U R E 30.0 20.0 S 1 10.0 0.0 -14.7 200 300 400 500 600 700 800 900 1000 FLOW (GPM)