The URL can be used to link to this page

Home My WebLink About1190 MAGNOLIA AVE; ; AS070177; Permit5/30/25, 11:53 AM AS070177 Permit Data City of Carlsbad Sprinkler Permit Job Address: 1190 MAGNOLIAAV Permit Type: SPRINK Parcel No: 2052109800 Lot #: 0 Permit No: AS070177 Status: ISSUED Applied 7/5/2007 Approved: 7/6/2007 Reference No.: Issued: 7/6/2007 PC #: Inspector: Project Title: SHAMSHOIAN RESIDENCE 3 RESIDENTIAL FIRE SPRINKLER INSPECTIONS @ $62/EA Applicant: INNOVATIVE FIRE PROTECTION 405 VERNON WAY ELCAJON (619) 593-8200 Owner: SHAMSHO IAN LUCIA E 1184 MAGNOLIA AVE CARLSBAD CA Fees ($) Add'l Fees ($) Total ($) Balance ($) 186 0 186 0 about:blank 1/1 SPRINKLER SYSTEM HYDRAULIC ANALYSIS Page 1 DATE: 5/30/2007 C:\HASS78\C3671.SDF JOB TITLE: SHAMSHOIAN RESIDENCE II - TWO HEAD CALC - MEZZANINE VAULT WATER SUPPLY DATA SOURCE STATIC RESID. FLOW AVAIL. TOTAL REQ'D NODE PRESS. PRESS. @ PRESS. @ DEMAND PRESS. TAG (PSI) (PSI) (GPM) (PSI) (GPM) (PSI) 1 83.0 80.0 500.0 83.0 31.2 60.1 AGGREGATE FLOW ANALYSIS: TOTAL FLOW AT SOURCE 31.2 GPM TOTAL HOSE STREAM ALLOWANCE AT SOURCE 0.0 GPM OTHER HOSE STREAM ALLOWANCES 5.0 GPM TOTAL DISCHARGE FROM ACTIVE SPRINKLERS 26.2 GPM NODE ANALYSIS DATA NODE TAG ELEVATION NODE TYPE PRESSURE DISCHARGE (ET) (PSI) (GPM) 1 121.0 SOURCE 60.1 31.2 2 121.0 - - - - 50.3 - - - 2A 121.0 - - - - 46.3 - - - 3A 121.0 HOSE STREAM 43.7 5.0 DC 122.0 - - - - 42.0 - - - DA 122.0 - - - - 35.0 - - - 3 123.0 - - - 33.3 - - - 4 126.0 - - - - 30.3 - - - 5 131.0 - - - - 23.3 - - - 6 133.5 - - - 19.8 - - 7 142.5 - - - - 14.9 - - - 8 142.5 - - - - 13.1 - - - 9 142.5 - - - - 12.9 - - - 9A 148.0 - - - - 10.2 - - - 9B 149.0 K= 4.30 9.1 13.0 10 142.5 - - - - 13.1 - - - 10A 148.0 - - - - 10.3 - - - 108 149.0 K= 4.30 9.3 13.1 11 12 142.5 144.0 - - - - - - - - 14.9 15.2 - - - - - APPROVED ///67 1LL) 13 133.5 - - - - 20.0 - - -t APPROVED AS NOTED ROVED SUBMIT NOT APP, RE CECI(G IS CLY FOR COcF0RMAN! THE ESO!J C0HEfl c THE H9 COWPLiP TH THE T' GVFi TiE CGTRACT "EITS 'T0R IS RESPONSIBLE SCIS fO BE C'jNFIBMED LAftO Al THE JOB / S AND H1R COORDINATION O THE kJ TRADES. SPRINKLER SYSTEM HYDRAULIC ANALYSIS Page 2 DATE: 5/30/2007 C:\HASS78\C3671.SDF JOB TITLE: SHANSHOIAN RESIDENCE II - TO HEAD CALC - MEZZANINE VAULT PIPE DATA PIPE TAG Q(GPM) DIA(IN) LENGTH PRESS. END ELEV. NOZ. PT DISC. VEL(FPS) HW(C) (FT) SUM. NODES (FT) (K) (PSI) (GPM) FL/FT (PSI) Pipe: 1 31.2 0.995 PL 30.00 PF 9.9 1 121.0 SRCE 60.1 (N/A) 12.9 150 FTG TG PE 0.0 2 121.0 0.0 50.3 0.0 0.253 TL 39.00 PV Pipe: 2 FIXED PRESSURE LOSS DEVICE 2 121.0 0.0 50.3 0.0 4.0 psi, 31.1 gpm 2A 121.0 0.0 46.3 0.0 Pipe: 3 31.1 1.360 PL 40.00 PF 2.5 2A 121.0 0.0 46.3 0.0 6.9 150 FTG 3L PE 0.0 3A 121.0 H.S. 43.7 5.0 0.055 TL 46.00 PV Pipe: 4 26.1 1.025 PL 3.00 PF 1.3 3A 121.0 H.S. 43.7 5.0 10.2 150 FTG EL PE -0.4 DC 122.0 0.0 42.0 0.0 0.158 TL 8.00 PV Pipe: 5 FIXED PRESSURE LOSS DEVICE DC 122.0 0.0 42.0 0.0 7.0 psi, 26.1 gpm DA 122.0 0.0 35.0 0.0 Pipe: 6 26.1 1.025 PL 3.00 PF 1.3 DA 122.0 0.0 35.0 0.0 10.2 150 FTG EL PE -0.4 3 123.0 0.0 33.3 0.0 0.158 TL 8.00 PV Pipe: 7 26.1 1.049 PL 3.00 PF 1.7 3 123.0 0.0 33.3 0.0 9.7 120 FTG C PE -1.3 4 126.0 0.0 30.3 0.0 0.213 TL 8.00 PV Pipe: 8 26.1 1.101 PL 27.00 PF 4.9 4 126.0 0.0 30.3 0.0 8.8 150 FTG E2T PE -2.2 5 131.0 0.0 23.3 0.0 0.112 TL 44.00 PV Pipe: 9 15.5 1.101 PL 24.50 PF 2.3 5 131.0 0.0 23.3 0.0 5.2 150 FTG 2E3TR PE -1.1 6 133.5 0.0 19.8 0.0 0.043 TL 54.50 PV Pipe: 10 15.5 1.101 PL 10.00 PF 1.0 6 133.5 0.0 19.8 0.0 5.2 150 FTG 2E PE -3.9 7 142.5 0.0 14.9 0.0 0.043 TL 24.00 PV Pipe: 11 16.0 1.101 PL 26.50 PF 1.8 7 142.5 0.0 14.9 0.0 5.4 150 FTG 2T3R PE 0.0 8 142.5 0.0 13.1 0.0 0.045 TL 39.50 PV Pipe: 12 13.0 1.101 PL 2.00 PF 0.2 8 142.5 0.0 13.1 0.0 4.4 150 FTG T PE 0.0 9 142.5 0.0 12.9 0.0 0.031 TL 7.00 PV SPRINKLER SYSTEM HYDRAULIC ANALYSIS Page 3 DATE: 5/30/2007 C:\HASS78\C3671.SDF JOB TITLE: SHAMSHOIAN RESIDENCE II - TWO HEAD CALC - MEZZANINE VAULT PIPE TAG Q(GPM) DIA(IN) LENGTH PRESS. END ELEV. NOZ. PT DISC. VEL(FPS) HW(C) (FT) SUM. NODES (FT) (K) (PSI) (GPM) FL/FT (PSI) Pipe: 13 13.0 1.101 PL 5.50 PF 0.4 9 142.5 0.0 12.9 0.0 4.4 150 FTG E PE -2.4 9A 148.0 0.0 10.2 0.0 0.031 TL 12.50 PV Pipe: 14 13.0 1.101 PL 4.00 PF 0.6 9A 148.0 0.0 10.2 0.0 4.4 150 FTG 2ER PH -0.4 9B 149.0 4.3 9.1 13.0 0.031 TL 19.00 PV Pipe: 15 3.0 1.101 PL 20.00 PF 0.1 8 142.5 0.0 13.1 0.0 1.0 150 FTG 2H4R PE 0.0 10 142.5 0.0 13.1 0.0 0.002 TL 38.00 PV Pipe: 16 13.1 1.101 PL 5.50 PE 0.3 10 142.5 0.0 13.1 0.0 4.4 150 FTG T PH -2.4 10A 148.0 0.0 10.3 0.0 0.031 TL 10.50 PV Pipe: 17 13.1 1.101 PL 4.00 PF 0.6 10A 148.0 0.0 10.3 0.0 4.4 150 FTG 2ER PH -0.4 lOB 149.0 4.3 9.3 13.1 0.031 TL 19.00 PV Pipe: 18 -10.1 1.101 PL 35.00 PF 1.9 10 142.5 0.0 13.1 0.0 3.4 150 FTG 8E6R PE 0.0 11 142.5 0.0 14.9 0.0 0.019 TL 97.00 PV Pipe: 19 0.5 1.101 PL 17.00 PF 0.0 11 142.5 0.0 14.9 0.0 0.2 150 FTG 2T3R PE 0.0 7 142.5 0.0 14.9 0.0 0.000 TL 30.00 PV Pipe: 20 -10.6 1.101 PL 16.00 PF 0.9 11 142.5 0.0 14.9 0.0 3.6 150 FTG 3ETR PH -0.6 12 144.0 . 0.0 15.2 0.0 0.021 TL 43.00 PV Pipe: 21 -10.6 1.101 PL 10.50 PF 0.3 12 144.0 0.0 15.2 0.0 3.6 150 FTG T PH 4.5 13 133.5 0.0 20.0 0.0 0.021 TL 15.50 PV Pipe: 22 -10.6 1.101 PL 52.50 PF 2.1 13 133.5 0.0 20.0 0.0 3.6 150 FTG 4E4TR PH 1.1 5 131.0 0.0 23.3 0.0 0.021 TL 101.50 PV NOTES: (1) Calculations were performed by the HASS 7.8 computer program under license no. 16080621 granted by 1-IRS Systems, Inc. 4792 LaVista Road Tucker, GA 30084 SPRINKLER SYSTEM HYDRAULIC ANALYSIS Page 4 DATE: 5/30/2007 C:\HA5578\C3671.SDF JOB TITLE: SHAMSHOIAN RESIDENCE II - TWO HEAD CALC - MEZZANINE VAULT The system has been calculated to provide an average imbalance at each node of 0.010 gpm and a maximum imbalance at any node of 0.188 gpm. Total pressure at each node is used in balancing the system. Maximum water velocity is 12.9 ft/sec at pipe 1. PIPE FITTINGS TABLE Pipe Table Name: FSS.PIP PAGE: A MATERIAL: SCH40 HWC: 120 Diameter Equivalent Fitting Lengths in Feet (in) E T L C. B G A D Ell Tee 1.049 2.00 5.00 2.00 5.00 6.00 1.00 1.00 1.00 PAGE: H MATERIAL: CPVC HWC: 150 Diameter Equivalent Fitting Lengths in Feet (in) H T R K C L B L Ell Tee TEERUN COUPLG EL45 1.101 7.00 5.00 1.00 0.00 1.00 1.00 0.00 1.00 PAGE: I MATERIAL: CPPR-L HWC: 150 Diameter Equivalent Fitting Lengths in Feet (in) H T L C B G A D Ell Tee 1.025 3.00 8.00 2.00 8.00 2.00 2.00 0.00 0.00 PAGE: J MATERIAL: S40PVC HWC: 150 Diameter Equivalent Fitting Lengths in Feet (in) E T L C B G A D Ell Tee 1.360 5.00 9.00 2.00 11.00 6.00 2.00 0.00 0.00 PAGE: K MATERIAL: CPPR-K HWC: 150 Diameter Equivalent Fitting Lengths in Feet (in) H T L C B G A D Eli Tee L 0.995 2.00 6.00 1.50 0.50 0.50 3.00 0.00 0.00 WATER SUPPLY ANALYSIS 100.0 1 G 80.0 A U G E P 60.0 R E S S 40.0 ie S ± 20 . 0 0.0 LO.L.LL. O..).'J%J ljo U. J.VL) £Juw; .)%JU.0 y piL LEGEND Available pressure 82.98 psi @ 31.2 gpm Required pressure 2 60.13 psi 8 31.2 gpm Source Supply Curve System Demand Curve —14.7 200 300 400 500 600 700 800 900 1000 FLOW (GPM) SPRINKLER SYSTEM HYDRAULIC ANALYSIS Page 6 DATE: 5/30/2007 C:\HASS78\C3671.sDF JOB TITLE: SHANSHOIAN RESIDENCE II - TWO HEAD CALC - MEZZANINE VAULT WATER SUPPLY CURVE 84+ 0\\\\\\\\\\\\\\\\\ I * <-80.0 psi @ 500 gpm I Flow Test Point 77+ 70+ 63+ x P 56+ R E S I S 49+ U R I E I 42+ ( I P I S I. 35+ 28+ 21+ 14+ LEGEND I H I X = Required Water Supply I 60.13 psi @ 31.2 gpm 7+ I 0 = Available Water Supply I 82.98 psi @ 31.2 gpm 0++-+---+----+-----+------+--------+--------+---------+-----------+ 200 300 400 500 600 700 800 900 1000 FLOW (GPM) APPROVE, SUBMITTED tXC!1DFERTMENT MODEL 950 FEATURES 3/40 to 2N C1 Double check valve assembly consisting of two independently operated spring-loaded "Y" type center guided check valves O Complete with two full port resilient seated ball valves for shut-off and four resilient seated ball valve test cocks Bronze body construction C) Entire unit serviceable in-line C1 Replacable seat option available ij Available with BSP - threads (less shut-off valves) Maximum operating pressure: 175 psi 0 Temperature range: 33°F to 140°F O STANDARDS: A3SE (No. 1015), IAPMO®, AWWA, GSA B64.5, USG/FCCC & HR / OPTIONS / Model 950XL Same as 950 except supplied with Noryl replaceable seats and silicone rubber check discs. (temperature range 33°F to 1800F). Model 950L Same as 950 except supplied less shut-off valves. Model 950LXL Same as 950XL except supplied less shut-off valves. Model 950S Same as 950 except supplied with "Y" strainer. Model 950XLS Same as 950XL except supplied with"Y strainer. Model 950U Same as 950 except supplied with union connections between ball valves and the device. Model 950US Same as 950U except supplied with "V strainer. Model 950XLU Same as 950XL except supplied with union connections between ball valves and the device. Model 950XLUS Same as 950XLU except supplied with strainer. 22 a 20 C') CL u 15 0 a. .90 U) U) 0 ui 60 a: Cl-) 30 a: a 0 0 40 80 120 160 200 240 FLOW RATE (U.S. GPM) FLOW RATE (L/S) 23 DIMENSIONS &WEIGHTS DIMENSIONS (In.) WEIGHT (Ib8.) MODEL A A B LESS LESS WITH SIZE BALL DOUBLE UNION BALL BALL BALL VALVES BALL VALVES VALVES C D E F VALVES VALVES 3/4 11.12 12.50 7.00 3.10 2.77 2.87 1.22 4.80 6.47 1 12.37 13.75 7.00 3.10 2.77 2.87 1.22 4.80 7.75 1114 17.00 N/A 10.57 4.40 4.33 3.50 1.98 11.13 15.75 1112 17.62 19.12 10.57 4.40 4.33 3.50 1.98 11.55 18.30 2 18.25 20.00 10.57 4.40 4.33 3.50 1.98 1 11.92 23.05 FLOW CHARACTERISTICS AMERICAN STANDARD METRIC STANDARD 0 10 20 30 40 50 60 0 1 2 3 4 FLOW RATE (U.S. GPM) FLOW RATE (IfS) a 20 ' Fl Res 49 Recessed Pendent/ F1 Fl Res 44 Recessed HSW/F2 Fl Res 40 Recessed HSW/F2 Fl Res 49 Pendent Fl Res 44 HSW Fl Res 40 HSW RFC 43 Bulletin 035 Rev.0 tEl C CD 0 (A) Cii CD C-) 11abl ,ee Residential Sprinklers For Sloped Ceilings Guidelines for Listed Residential Sprinkler installations below Sloped Ceilings Fl Res 49 Recessed Pendent/11711 Fl Res 44 HSW Fl Res 44 Recessed HSW/F2 Fl Res 40 HSW Fl Res 40 Recessed HSW/F2 Fl Res 49CCP RFC 43 Flat Concealed Listings & Approvals Listed by Underwriters Laboratories Inc. and UL Certified for Canada (cULus) NYC MEA 258-93-E UL Listing Category Residential Automatic Sprinkler UL Guide Number VKKW Patents: US Patent number 6,516,893 Model Fl Res 49 The Installation guidelines cover I Residential Sprinkler Models: Fl Res 49 Pendent Product Description for Fl Res Sprinklers Model Fl Res Pendent sprinklers are fast response sprinklers combining excellent durability, high sensitivity glass-bulb and low profile decorative design. The Fl Res Horizontal Sidewall sprinklers are equally attractive when above ceiling piping cannot be used. The 3mm glass-bulb pendent sprinklers, with a K Factor of 4.9 for pendent and 4.4 for horizontal sidewall, permit the efficient use of residential water supplies for sprinkler coverage in residential fire protection design. The low flow Fl Res sprinklers are specially engineered for fast thermal response to meet the sensitive fire protection application needs of the latest residential market standards (UL 1626 Standard *) Upon fire conditions, rising heat causes a sprinkler's heat-sensitive glass-bulb to shatter, releasing the waterway for water flow onto the deflector, evenly distributing the discharged water to control a fire. Fl Res 49 CCP Pendent RFC 43 * Effective date July 12, 2002 The Reliable Automatic Sprinkler Co., lnc.d 525 North MacQuesten Parkway, Mount Vernon, New York 10552 Product DescriptionRFC 43 Model RFC43 Concealed Residential Sprinklers are fast response residential fusible solder link automatic sprinklers. Residential sprinklers differ from standard sprinklers primarily in their response time and water distribution patterns. Model RFC43 sprinklers discharge water in a hemispherical pattern below the sprinkler deflector. Residential distribution patterns are higher and generally contain a finer droplet size than standard sprinkler patterns. The combination of speed of operation and high discharge pattern required for residential sprinklers has demonstrated, in fire testing, an ability for controlling residential fires, and thereby providing significant evacuation time for occupants. The RFC43 Sprinkler provides the best form of fire protection by combining an attractive appearance and ½" (13mm) of cover adjustment for ease of installation. The small diameter cover plate is easily and positively attached and blends into the ceiling, concealing the most dependable fire protection available, an automatic sprinkler system. The RFC43 is a UL Listed Residential Sprinkler to be installed in the residential portions of any occupancy in accordance with NFPA 13,13R, & 13D. The RFC43 can reduce the need for precise cutting of drop nipples. The threaded cover plate assembly can be adjusted without tools to fit accurately against the ceiling. The fire protection system need not be shut down to adjust or remove the cover plate assembly. Technical Data (Fl Res Sprinklers): Thermal Sensor: Nominal 3mm glass-bulb • Sprinkler Frame: Brass Casting Sprinkler Pressure Rating: 175 psi Factory Hydrostatically Tested to 500 psi Thread Size : ½' NPT (R½) K Factor : 4.9 (Actual) - Fl Res 49 Pendent Sprinkler 4.4 (Actual) - Fl Res 44 HSW Sprinkler 4.0 (Actual) - Fl Res 40 HSW Sprinkler • Density : Minimum .05 gpm/ft2 Technical Data (RFC 43): Thermal Sensor: 165°F Fusible Link • Sprinkler Frame: Brass Machined Sprinkler Pressure Rating: 175 psi Factory Hydrostatically Tested to 500 psi Thread Size : ½' NPT (R½) K Factor : 4.3 (Actual) Density : Minimum .05 gpm/ft2 Application Model Fl Res and RFC 43 Sprinklers are used for Residential Fire Protection according to UL 1626 Standard*. Be sure that orifice size, temperature rating, deflector style, cover plate and sprinkler type are in accordance with the latest published standards of The National Fire Protection Association or the approving Authority Having Jurisdiction. * Effective date July 12, 2002 2. METHOD OF CALCULATING THE CONVERSION OF 'RISE—OVER—RUN' TO DEGREES OF AN ANGLE. (rise) = TAN-' (0/b) 2. slope distance: c = 7 7b* Example: a = 4 b = 12 .4A = TAN-' (alb) = TAN-' = (0.333) = 18.43' 035_ROR-A slope distance: a = '4_+12k C '160 C = 12.65 1 3. Model Fl Res 49 Pendent & Fl Res 49 Recessed Pendent/F1 & Fl Res 49 CCP Pendent & RFC 43 Pendent Flat Concealed Sprinklers installed below Sloped Ceilings. Fl Res 49 Pendent Fl Res 49 Recessed Pendent / F2 Fl Res 49 COP Pendent RFC 43 RFC 43 4. L/2 JI'IJIL'J' B LISTED AREA OF COVERAGE CORRESPONDS TO CEILING SLOPE - L = THE MAXIMUM LISTED SPRINKLER SPACING, LENGTH (8'-0" MINIMUM). L/2 = ONE HALF THE MAXIMUM LISTED SPRINKLER SPACING (0'-4 MINIMUM). W = THE MAXIMUM LISTED SPRINKLER SPACING, WIDTH. A = 3'-0 MAXIMUM. B = RANGE: 2/12 (9.4') < B :9 8/12 (33.7'). C = 8'-0" MINIMUM. Sprinkler spacing below single sloped ceilings with a maximum slope of 8/2 (33.70) pitch. II L L1D AREA OF CO~ CORRESPOAOS 10 cE(MG SU L = THE MAXIMUM LISTED SPRINKLER SPACING. LENGTH (8'-0 MINIMUM). 1/2 = ONE HALF THE MAXIMUM LISTED SPRINKLER SPACING (0'-4 MINIMUM). W = THE MAXIMUM LISTED SPRINKLER SPACING. WIDTH. A = 34 0* MAXIMUM. B = RANGE: 2/12(9A')'cB8/12(33.T). C = 8'—O" MINIMUM. Sprinkler spacing below multiple sloped ceilings with a maximum slope of 8/2 (33.70) pitch. I Model Fl Res 49 Pendent & Fl Res 49 Recessed Pendent/F2 installed below Sloped Ceiling. Technical Data Thread Sire Max. Pressure psi (bar) Max. Ambient Temp. I OF I Actual K Factor I Sj,rhi Length Escutcheon i I Sprinkler I Identification (°C) (metric) I I Number (SIN) I ½"NPT(R½) 175 (12) 100(38) 4.9(69,94) 2.25" I (Y" F2 Adjustment) R3516 Table 1 - Application Max. Sprinkler Spacing Along Slope (W)Wldthx(L)Length it (m) Max. Slope of ¶42(33.7°) Pitch Max. Slope of ¶42(18.4°) Pitch Sprinkler Temp. Rating °F (°C) 155(68) Sprinkler Temp. Rating °F (°C) 155 (68) & 175 (79 Mm. Flow Per Sprinkler Head gpm (Lpm) Pressure psi (bar) Mm. Flow Per Sprinkler Head gpm (Lpm) Pressure psi (bar) 12 x 12 (3,6 x 3,6) 19(71,9) 15.1 (1,04) 13(49) 7.0(0,48) 14x 14(4,3x4,3) 19(71,9) 15.1 (1,04) 13(49) 7.0(0,48) 16 x 16 (4,9 x 4,9) 19(71,9) 15.1 (1,04) 13(49) 7.0(0,48) 18 x 18 (5,5 x 5,5) 20(75,7) 16.7(1,15) 17(64,3) 12.0(0,83) 20 x 20 (6,1 x 6, 1) 25(94,5) 26(1,78) 20(75,7) 16.7(1,15) Model Fl Res 49 CCP Pendent installed below Sloped Ceiling. Technical Data Sprinkler Temp. CCP Assy. I Temp. I Max I I Max. I Ambient Actual I K I I Sprinkler I I Sprinkler Thread Size Rat1n °F (°C Rating I Pressure I Temp. Factor I length Identification °F (°C) psi (bar) I °m (°C) (metric) I Number (SIN) y2"NPT(Ry2) 155(68) 135 (57) I 175 (12) I 100 (38) I 4.9(69,94) I 2.25" I R3516 I Table 2- Application Max. Sprinkler Spacing Along Slope (W) Width x ( L) Length ft (m) Max. Slope of 8A2 (33.7°) Pitch Min. Flow Per Sprinkler Head Pressure gpm (Lpm) psi (bar) Max. Slope of ,42 (18.4° Pitch Mm. Flow Per Sprinkler Head Pressure gpm (Lpm) psi (bar) 12 x 12(3,6 x 3,6) 20(75,7) 16.7(1,15) 13(49) 7.0(0,48) 14 x 14(4,3 x 4,3) 20(75,7) 16.7(1,15) 13(49) 7.0 (0,48) 16 x 16(4,9 x 4,9) 20(75,7) 16.7(1,15) 14(53) 18x 18(5,5x5,5) 21(79,4) 18.4(1,27) 20x20(6,1 x6,1) 21(79,4) 18.4 (1.27) Model RFC 43 Pendent Flat Concealed installed below Sloped Ceiling. Technical Data Thread Size Sprinkler Rating I Coverplate I Temp. Rating °(°C) I Max. I Pressure psi (bar) I Max. I Ambient Temp. I °F(°C) I Actual J K Factor (metric) Max. lAdlUstmentl I Sprinkler I Identification I Number (SIN) Y2" NPT (R½) I 165(74) 135(57) 175(12) 100(38) I 4.3 (61,4) I Y. RA0612 Table 3- Application Max. Sprinkler Spacing Along Slope (W) Width x ( L) Length ft (m) Max. Slope of 6A2 (33.7°' Pitch Mm. Flow Per Sprinkler Head Pressure gpm (Lpm) psi (bar) Max. Slope of ¶42(18.4°' Pitch Mm. Flow Per Sprinkler Head Pressure gpm (Lpm) psi (bar) 12 x 12 (3,6 x 3,6) 18(68) 17.5 (1,21) 13(49) 9.1(0,63) 14 x 14 (4,3 x 4,3) 18(68) 17.5 (1,21) 13(49) 9.1(0,63) 16x 16(4,9x4,9) 18(68) 17.5(1,21) 13(49) 9.1(0,63) 18 x 18(5,5 x 5,5) 21(79) 23.8 (1,654) 20x20(6,1 x6,1) 21(79) 23.8(1,64) 1 7. Fl Res 44 Recessed HSW/F2 Horizontal Sidewall Sprinkler (with discharge directed across the slope) Fl Res44 Installation Guidelines For systems designed in accordance with NFPA 13, 13D and 13R, where specific UL Listed flows are not required, consult with the local Authority Having Jurisdiction regarding the number of design sprinklers for sloped ceilings having a pitch greater than Y12(9.40). Installation of UL Listed residential sprinklers under sloped ceilings shall be limited to a type of unobstructed construction consisting of smooth ceiliflgs, as defined b NFPA 13, having a maximum pitch of 4/12(18.4°) or 8/1 (33.7°). Spacing of residential sprinklers under sloped ceilings is measured along the slope when determining the distance off of walls and between sprinklers. Measure listed areas of coverage along the sloped ceiling. The actual floor coverage area wifi be less than the listed area. For coverage areas less than the listed coverage area shown in Tables 1 through 5, use the minimum flow requirement for the next largest listed coverage area. Minimum spacing between pendent type sprinklers is 8 ft. (2.4 m). Minimum distance from a pendent type sprinkler and an adjacent wall is 4' (102 mm). Residential sprinklers located closest to the peak of the ceiling shall have the deflectors located not more than 3 ft (11 m) vertically down from the peak. Align deflectors parallel with the ceiling slope 1' to 4" (25mm to 102mm) below the sloped ceiling. Hydraulic Requirements: For NFPA 13D Systems, the number of design sprinklers shall include all sprinklers within a compartment up to a maximum of two sprinklers (where specific UL Listed flows are required) that requires the greatest hydraulic demand. For NFPA 13R Systems, the number of design sprinklers shall include all sprinklers within a compartment up to a maximum of four (4) sprinklers (where specific UL Listed flows are required), that requires the greatest hydraulic demand. For NFPA 13 systems, the design area shall be the area that includes the four (4J hydraulically most demanding sprinklers. The minimum required discharge from each of the four hydraulically demanding sprinklers shall be the greater of the following: In accordance with the minimum flow rates indicated by the individual listings (that already will provide a minimum density ofO. 1 gprrVft2); or A calculated value based on delivering a minimum of 0.1 gprrVft2 over the design area. Because of the varied nature of residential construction features, there will be some compartment designs which cannot be fully sprinklered in accordance with NFPA 13, 13D, or 13R. In these instances, consult the Authority Having Jurisdiction (AHJ) for guidance and approval. This includes sloped ceilings having a pitch greater than 8/12 (33.7°). Model Fl Res 44 & 40 HSW and Fl Res 44 & 40 Recessed HSW/F2 installed below the slope ceiling. Fir LISTED AREA OF COVERAGE CORRESPONDS TO CEILING SLOPE TOP OF DEFLECTOR MUST BE LOCATED 4 TO 12' BELOW SLOPED CEILING. THE TOP OF THE DEFLECTOR OUST BE PARALLEL WITH THE PLANE OF THE CEILING. L DISCHARGE IS ACROSS THE SLOPE. ELEVATION L = THE MAXIMUM USTED SPRINKLER SPACING, LENGTH. W = THE MAXIMUM LISTED SPRINKLER SPACING, WIDTH. W/2 = ONE—HALF THE MAXIMUM LISTED SPRINKLER SPACING, WIDTH (0'-4" MINIMUM). A = 3'-0" MAXIMUM. B = RANGE: 2/12 (9.4') < B ic 8/12 (33.7'). C = 8'-0" MINIMUM. HSW sprinkler spacing below single sloped ceilings with a maximum slope of 8/2 (33.7°) pitch. w /2 W/2 41/2 Lls7rD AREA OF COHERACE CORRESPONDS 70 CEILiNG SLOPE F. TOP OF DEFLECTOR *AiSr BE LOCATED 4 70 I2 BELOW SLOPED CEILING. ELEVATiON THE TOP OF THE OtflEC10R KIST BE R4RAUEL $lflI THE PLANE OP Flit CEILING. D6C?i4RCE IS .4L Flit SLOPE. -. L = THE MAXIMUM LISTED SPRINKLER SPACING. LENGTH. W = THE MAXIMUM LISTED SPRINKLER SPACING. WIDTH (0'-4 MINIMUM). W/2 = ONE—HALF THE MAXIMUM LISTED SPRINKLER SPACING. WIDTH (0'-4 MINIMUM). A 3-0 MAXIMUM. B = RANGE: 2/12 (9.4') B a 8/12 (33.7). C = 81-0" MINIMUM. HSW Sprinkler spacing below multiple sloped ceilings with a maximum slope of 8/2 (33.70) pitch. 9. / rable 5 - Application Discharge Directed Down the Slope 4" to 6" Deflector to Ceiling Discharge Directed Down the Slope 6" to 12" Deflector to Ceiling Discharge Directed Across the Slope 4" to 6" Deflector to Ceiling Max. Sprinkler Spacing Along Slope (W) Width x ( L) Length ft (m) Min. Flow gpm (Lpm) Pressure psi (bar) 'Mln. Flow gpm (Lpm) Pressure psi (bar) 1Mln. Flow gpm (Lpm) Pressure psi (bar) 12 x 12(3,6 x 3,6) 13 (49,0) 10.6(0,73) 13(49,0) 10.6(0,73) 17(64,3) 18.1 (1,24) 14 x 14 (4,3 x 4,3) 16 (605) 16 (1,10) 17(64,3) 18.1 (1,10) 17(69,3) 18.1 (1,24) 16x 16(4,9x4,9) 17 (64,3) 18.1 (1,24) 20(75,7) 25 (1,72) 17(64,3) 18.1 (1,24) 16 x 18 (4,9 x 5,5) 20°(75,7) 25° (172) 16 x 20 (4,9 x 6, 1) 23 (87,0) 33.1(2,28) *Min flow and pressure on 175°F temperature rating only is 21 gpm (79,5 Lpm) and 27.6_ psi bar) _(1,9 ________________________ ___ Escutcheons Recessed with F2 Recessed with F2 Standard or raised mount only Temperature Rating OF (°C) 155(68),175 (79) 155(68), 175(79) 155(68) (1) Minimum Flow Per Sprinkler gpm (Lpm) Installation Guidelines For systems designed in accordance with NFPA 13, 130 and 13R, where specific UL Listed flows are not required, consult with the local Authority Having Jurisdiction regarding the number of design sprinklers for sloped ceilings having pitch greater than 2/2 (9.411 ). Installation of UL Listed residential sprinklers under sloped ceilings shall be limited to a type of unobstructed construction consisting of flat, smooth ceilings, as defined by NFPA 13, having a maximum pitch of 4/12 (18.40) or 8112 (33.70). Where listed, install horizontal sidewall sprinklers along the wall below the sloped ceiling when discharge is directed across the slope, and install at the peak below the sloped ceiling when discharge is directed down the slope. Always align the sprinkler deflector parallel with the direction of the sloped ceiling. Residential HSW sprinklers located closed to the peak of the ceiling shall have the deflectors located not more than 3 ft. (11 m) vertically down from the peak. Spacing of residential HSW sprinklers under sloped ceilings is measured along the slope when determining the distance off of walls and between sprinklers. Measure listed areas of coverage along the sloped ceiling. The actual floor coverage area will be less than the listed area. For coverage areas less than the listed coverage area shown in Tables 1 through 5, use the minimum flow requirement for next largest listed coverage area. Minimum spacing between horizontal sidewall sprinklers is 8 ft. (2.4 m). Minimum distance from a horizontal sidewall sprinkler and an adjacent wall is 4" (102 mm). Where installation of Fl Res 40 horizontal sidewall sprinklers provide discharge across a slope having a maximum pitch of 8/12, F2 escutcheons may be used for surface mounting only. Hydraulic Requirements: For NFPA 130 Systems, the number of design sprinklers shall include all sprinklers within a compartment up to a maximum of two sprinklers (where speciic UL Listed flows are required) that requires the greatest hydraulic demand. Exception: For Fl Res 40 horizontal sidewall sprinklers, where discharge is directed across a slope having a maximum pitch of 8/12 and the compartment that requires the greatest hydraulic demand is large enough where three (3) or more sprinklers are required for adequate coverage, the minimum number of design sprinklers within that compartment shall be three (3), where specific UL Listed flows are required. For NFPA 13R Systems, the number of design sprinklers shall include all sprinklers within a compartment, up to a maximum of four (4) sprinklers (where specific UL Listed flows are required), that requires the greatest hydraulic demand. For NFPA 13 systems, the design area shall be the area that includes the four (4) hydraulically most demanding sprinklers. The minimum required discharge from each of the four hydraulically demanding sprinklers shall be the greater of the following: In accordance with the minimum flow rates indicated by the individual listings (that already will provide a minimum density of 0.1 gprrVft2); or A calculated value based on delivering a minimum of 0.1 gprrv1t2 over the design area. Because of the varied nature of residential construction features, there will be some compartment designs which cannot be fully sprinklered in accordance with NFPA 13, 130, or 13R. In these instances, consult the Authority Having Jurisdiction (AHJ) for guidance and approval. This includes sloped ceilings having a pitch greater than 8/12(33.7). 11. Model Fl Res 44 HSW & Fl Res 44 HSW Recessed HSW/F2 with a maximum slope of %2(18.4°) pitch. Technical Data r Thread Sprinkler Max. I I Max. I I Actual I Sprinkler I Sprinkler I I I Size Temp Rating . Pressure Ambient Temp. K Factor Length Escutcheon Identification OF (°C) psi (bar) OF (°C) (metric) Number (SIN) I I ½" NPT(R½) 155(68)175 (79) 175(12) 100(38) 4.4(62,8) 2.45" ('/2" F2 adjustment)I R3531 Table 4 - Application Discharge Directed Across the Slope 4" to 6" Deflector to Ceiling Discharge Directed Across the Slope 6" to 12" Deflector to Ceiling Max. Sprinkler Spacing Along Slope (W) Width x ( L) Length ft (m) Mm. Flow gpm (Lpm) Pressure psi (bar) Mm. Flow gpm (Lpm) Pressure psi (bar) 12 x 12 (3,6 x 3,6) 16 (60,5) 13.3(0,92) 17(64,3) 15(1,04) 14x 14(4,3x4,3) 16 (60,5) 13.3 (0,92) 17(64,3) 15(1,04) 16 x 16 (4,9 x 4,9) 16 (60,5) 13.3(0, 2) 17(64,3) 15(104) 16 x 18(4,9 x 5,5) 18 (68,1) 16.8 (1,16) 20 (75,6) 20.7(1,43) 16x20(4,9x6,1) 23 (68,1) 27.4(1,89) 23(68,1) 27.4(1,89) Model Fl Res 40 HSW and Fl Res 40 HSW Recessed HSW/F2 with a maximum slope of %2 (33.7°) pitch. Fl Res 40 H Hes40 HSW Recessed HSW/F2 Technical Data Thread Max. I Max. Actual I K I Sprinkler I Sprinkler Size Pressure Ambient Temp. Factor I Length Identification psi (bar) OF (°C) (metric) Number (SIN) ½NPT(R½) 175(12) 100(38) I 4.0(57,09) 2.45" I R3538 10. Bulletin 136 Rev.L R'elmable Model Fl FR Model Fl FR Recessed Quick Response Sprinklers Model Fl FR Sprinkler Types Standard Upright Standard Pendent Conventional Vertical Sidewall Horizontal Sidewall - HSW 1 Deflector Model Fl FR Recessed Sprinkler Types Recessed Pendent Recessed Horizontal Sidewall - HSW 1 Deflector Listings & Approvals Listed by Underwriters Laboratories, Inc. (UL) Listed by Underwriters Laboratories of Canada (ULC) Certified by FM Approvals Loss Prevention Council (LPC, UK) NYC BS&A No. 587-75-SA Meets MIL-S-901C and MIL-STD 167-1 Verband der Schadenversicherer (VdS, Germany) NYC MEA 258-93-E I UL Listing Category Sprinklers, Automatic & Open Quick Response Sprinkler I UL Guide Number VNIV Product Description Reliable Models F1FR and F1FR Recessed Sprinklers are quick response sprinklers which combine the durability of a standard sprinkler with the attractive km profile of a decorative sprinkler. The Models Fl FR and El ER Recessed automatic sprinklers utilize a 3.0 mm frangible glass bulb. These sprinklers have demonstrated response times in laboratory tests which are live to ten times faster than standard response sprinklers. This quick response enables the Model F1FR and F1 FR Recessed sprinklers to apply water to a fire much faster than standard sprinklers of the same temperature rating. The glass bulb consists of an accurately controlled amount of special fluid hermetically sealed inside a precisely manufac- tured glass capsule. This glass bulb is specially constructed to provide fast thermal response. The balance of parts are made of brass, copper and beryllium nickel. At normal temperatures, the glass bulb contains the fluid in both the liquid and vapor phases. The vapor phase can be seen as a small bubble. As heat is applied, the liquid ex- pands, forcing the bubble smaller and smaller as the liquid pressure increases. Continued heating forces the liquid to push out against the bulb, causing the glass to shatter, opening the waterway and allowing the deflector to distrib- ute the discharging water. The temperature rating of the sprinkler is identified by the color of the glass bulb. Upright Pendent Vertical Sidewall Conventional / Horizontal Sidewall HSW 1 Deflector Recessed Pendent Application Quick response sprinklers are used in fixed fire protec- tion systems: Wet, Dry, Deluge or Preaction. Care must be exercised that the orifice size, temperature rating, deflector style and sprinkler type are in accordance with the latest published standards of the National Fire Protection Asso- ciation or the approving Authority Having Jurisdiction. Quick response sprinklers are intended for installation as specified in NFPA 13. Quick response sprinklers and stan- dard response sprinklers should not be intermixed. The Reliable Automatic Spunkier Co., Inc. 525 North MacQuesten Parkway, Mount Vernon, New York 10552 Upright Pendent Upright Model Fl FR Quick Response Upright, Pendent & Conventional Sprinklers Installation Wrench: Model D Sprinkler Wrench Installation Data: Sprinkler Type Standard-Upright (SSLJ) and Pendent (SSP) Deflectors Marked to Indicate K Factor _ Sprinkler Approval Organization Sprinkler Identification Number (SIN) us metric ssu ssp X" (15mm) Standard Orifice with ," NPT (AX) Thread 5.6 Q 2.2" (56mm) 1,2,34,5.6,7 83625 83615 %(2nm) Large Orifice with "NPT(R3A)Thread 8.0 115 2.3"(58rrm) 1,2,3,4,7.8 R3622 83612 /6 (l7mm) Small Orifice withX"NPT(R,Y2)Thread 4.2 1 60 2.54(65mm) 1,2.8 83623 R3613 " (lom) Small Orifice withX"NPT(R/2)Thread 2.8 40 2.54(65nTfl) 1,2,8 83621 83611 lOmm Orifice XLHwithR%"Thread 4.2 60 56.1mm 4,6,7 83624 - 83614 Conventional-Install in Upright or Pendent Position 4.2 5.6 8.0 60 80 115 56.1mm 56.1mm 58.4mm - 4,6,7 4.7 83674 83675 R3672 10mm Orifice XLH with R)Thread 15mm Standard Orifice with ," NPT (RX) Thread 20mm Large Orifice with 3R'NPT(R°A)Thread Conventional Model Fl FR Quick Response Recessed Pendent Sprinkler Installation Wrench: Model RC1 Sprinkler Wrench Installation Data: Nominal Orifice Thread - Size K Factor Sprinkler Height ApprovaiW Organizations Sprinkler Identification Number (SIN) US Metric /" (15mm) /" NPT(RY) 5.6 80 22"(56rnm) 1,2,3,4,5,7,8 R3615 y/32"(20nin) "NPT(R3%) 8.0 115 2.3" (58mm) 1,2,3 R3612 /6 (11 mm) )ç'NPT(81/2) 4.2 60 254" (65mm) 1,2,8 83613 %' (10mm) /"NPT(8Y2) 2.8 40 254(65mm) 1,2,8 83611 l0n-xn RY, 4.2 60 56.1mm 4.7 83614 Refer to escutcheon data table for approvals and dimensions. 2. Vertical Sidewall Model Fl FR Quick Response Vertical Sidewall Sprinkler Installation Wrench: Model D Sprinkler Wrench Installation Position: Upright or Pendent Approval Type: Light Hazard Occupancy Installation Data: Nominal Orifice Thread Size K Factor Sprinkler Height Approval Organizations Sprinkler Identification Number (SIN) US Metric ½" 1/2" NPT (RI/2) 5.6 80 2.2" (56mm) 1, 2.3.6.8 15mm ½" NPT (R½) 5.6 80 2.2" (56mm) 4(1) R3685 (1) LPC Approval is for Pendent position only. Orientation Deflector to Ceiling Dimension (Mm. - Max.) Upright J 4"- 12" (102mm - 305mm) Pendent I 6"- 12" (152mm - 305mm) Model Fl FR Quick Response Horizontal Sidewall Sprinkler Deflector: HSW 1 Installation Wrench: Model D Sprinkler Wrench Installation Data: K Factor I Approval Organizations I and Type of Approval I Sprinkler I Identification Nominal Orifice Thread Size US I I Metric I Sprinkler I Length Light Hazard I Ordinary I Hazard Number I (SIN) X"(lsmm) X"NPT(RV2) 5.6 80 2.63" (67mm) 1,2,3,5,8 1,2,5.8 R3635 NOTE: UL and ULC Listing permits use with Fl or F2 recessed escutcheon. Horizontal Sidewall 3. Installation Quick response sprinklers are intended for installation as specified in NFPA 13. Quick response sprinklers and standard response sprinklers should not be intermixed. The Model Fl FR Recessed Quick Response Sprinklers are to be installed as shown. The Model Fl or F2 Escutch- eons illustrated are the only recessed escutcheons to be used with the Model El ER Sprinklers. The use of any other recessed escutcheon will void all approvals and negate all warranties. When installing Model Fl FR Sprinklers, use the Model D Sprinkler Wrench. When installing Model Fl FR Recessed Sidewall Sprinklers, use the Model GFR1 Sprinkler Wrench. Use the Model RC1 Wrench for installing F1FR Recessed Pendent Sprinklers. Any other type of wrench may damage these sprinklers. Temperature Ratings Classification Sprinkler Max. Ambient Temp. Bulb Color C_ Ordinary 57 135 10(rF(38°c) Orange Ordinary 68 155 100-F(38"C) Red Intermediate 79 175 150-F (66-C) Yellow Intermediate 93 20) 150-F (66-C) Green High1t1 1 141 286 1 225-F(107-C) I Blue t) Not available for recessed sprinklers. Escutcheon Data Escutcheon "A" Face of Fitting Model 'A"Adiustaient Wad Dimension Fl 1.2.4 (19mm) (19mm) (5mm-24rrrr) F2 1.2.3.4.5.7.8 /2" 1" (13mm) (25mm) (5rwn- 17nyn) /6" F' 1,2 Fully Recessed (11mm) Push-on/ Thread-off 1,2 Fully Retracted V (24mm) Maintenance The Models F1FR and F1FR Recessed Sprinklers should be inspected quarterly and the sprinkler system maintained in accordance with NFPA 25. Do not clean sprinklers with soap and water, ammonia or any other cleaning fluids. Remove dust by using a soft brush or gen- tle vacuuming. Remove any sprinkler which has been painted (other than factory applied) or damaged in any way. A stock of spare sprinklers should be maintained to allow quick replacement of damaged or operated sprin- klers. Prior to installation, sprinklers should be maintained in the original cartons and packaging until used to mini- mize the potential for damage to sprinklers that would cause improper operation or non-operation. Sprinkler Types Standard Upright Standard Pendent Conventional Sidewall (Vertical, Horizontal HSW1) Recessed Pendent Recessed Horizontal Sidewall HSWl Finishes ""2' Standard Finishes Sprinkler Escutcheon Bronze Brass Chrome Plated Chrome Plated (31 White Polyester Coated White Painted (31 Special Application Finishes Sprinkler Escutcheon Bright Brass Bright Brass Black Plated Black Plated Black Paint Black Paint Off White Ott White Satin Chrome Satin Chrome Other finishes and colors are available on special order. Consult the factory for details. FM Approvals is limited to bronze and brass, chrome or black plated finishes only. FP Push-on/Thread-off escutcheon Ordering Information Specify: Sprinkler Model Sprinkler Type Orifice Size Deflector Type Temperature Rating Sprinkler Finish Escutcheon Type Escutcheon Finish (where applicable) Note: When Model F1FR Recessed sprinklers are ordered, the sprinklers and escutcheons are packaged separately. The equipment presented in this bulletin is to be installed in accordance with the latest pertinent Standards of the National Fire Protection Association. Factory Mutual Research Corporation, or other similar organizations and also with the provisions of governmental codes or ordinances whenever applicable. Products manufactured and distributed by Reliable have been protecting life and property for over 80 years. and are installed and serviced by the most highly qualified and reputa- ble sprinkler contractors located throughout the United States. Canada and foreign countries. Manufactured by Reliabld ~11 The Reliable Automatic Sprinkler Co., Inc. (800)431-1588 Sales Offices (800)848-6051 Sales Fax (914)668-3470 Corporate Offices www.retiablesprinklec.com Internet Address ® Recycled Paper Revision lines indicate updated or new data EG. Printed in U.S.A. 3,03 P1149999970027