Loading...
HomeMy WebLinkAbout1900 ASTON AVE; 100; CBC2019-0155; Permit(7avv of Building Permit Finaled Carlsbad _______________ __________ - .-.-.-.--.;-.-.---------.---_--------.---.-------------.--7------.-__----__-_'•__--,- Commercial Permit T Print Date: 05/08/2020 Permit No: CBC2019-0155 Job Address: 1900 Aston Ave, 100 Permit Type: BLDG-Commercial Work Class: Tenant Improvement . Status: Closed - Finaled Parcel No: 2121202400 Lot #: Applied: 04/05/2019 Valuation: $586,305.06 Reference #: Issued: 05/30/2019 Occupancy Group: Construction Type. PermitFinal Close Out: # Dwelling Units: e Bathrooms: Inspector: PBurn Bedrooms: Orig. Plan Check #: Final Plan Check #: Inspection: 05/08/2020 Project Title: . . Description: M2 INGREDIENTS: 12,606 SF OFFICE/MAUF/WAREHOUSE TO OFFICE/MAUF/WAREHOUSE Owner: Contractor: P D G CARLSBAD 59 LIMITED KELCHLIN CONSTRUCTION INC 1900 Aston Ave 13100 Kirkham Way, Ste 201 CARLSBAD, CA 92008 Poway, CA 92064-7128 858-513-3799 - FEE AMOUNT BUILDING PERMIT FEE ($2000+) - $2,298.00 BUILDING PLAN CHECK FEE (BLDG) . . $1,608.60 ELECTRICAL BLDG COMMERCIAL NEW/ADDITION/REMODEL . . $242.00 FIRE F Occupancies TI . . $628.00 FIRE Haz Mat Storage Chem Class <10 Chemicals $485.00 GREEN BUILDING STANDARDS PLAN CHECK & INSPECTION . $175.00 MECHANICAL BLDG COMMERCIAL NEW/ADDITION/REMODEL . $104.00 SB1473 GREEN BUILDING STATE STANDARDS FEE . . . . . $24.00 STRONG MOTION-COMMERCIAL . $164.17 Total Fees: $5,728.77 . Total Payments To Date: $5,728.77 Balance Due: $0.00 Please take NOTICE that approval of your project includes the "Imposition" of fees, dedications, reservations, or other exactions hereafter collectively referred to as "fees/exaction." You have 90 days from the date this permit was issued to protest imposition of these fees/exactions. If you protest them, you must follow the protest procedures set forth in Government Code Section 66020(a), and file the protest and any other required information with the City Manager for processing in accordance with Carlsbad Municipal Code Section 3.32.030. Failure to timely follow that procedure will bar any subsequent legal action to attack, review, set aside, void, or annul their imposition. J . You are hereby FURTHER NOTIFIED that your right to protest the specified fees/exactions DOES NOT APPLY to water and sewer connection fees and capacity changes, nor planning;zoning, grading or other similar application processing or service fees in connection with this project. NOR DOES IT APPLY to any fees/exactions of which you have previously been given a NOTICE similar to this, or as to which the statute of limitation has previously otherwise expired. Building Division 1635 Faraday Avenue, Carlsbad CA 92008-7314 1 760-602-2700 1 760-602-8560 f I www.carlsbadca.gov Page 1of 1 BUILDING PERMIT Plan Check C'C019 -O (City of COMMERCIAL Carlsbad APPL Est. Value ICATION PC Deposit B-2 Date Job Address 1900 Aston Ave. Suite: inn APN: 212-120-24-00 Tenant Name: M2 Ingredients CT/Project #: Lot #: 59 Occupancy: B. F-i, S-i Construction Type: V-B Fire Sprinklers: yes / no Air Conditioning: yes / no BRIEF DESCRIPTION OF WORK: Tenant improvement to renovate existing office, fabrication and warehouse areas. No change in Occupancy. El Addition/New: New SF and Use, New SF and Use, Deck SF, _________ Patio Cover SF (not including flatwork) Tenant Improvement: 12,606 SF, Existing Use B, F-i, S-i Proposed Use B, F-i, S-i SF, Existing Use Proposed Use IJ Pool/Spa: ____________ SF Additional Gas or Electrical Features? 0 Solar: KW, _____ Modules, _______ Mounted, Tilt: Yes / No, RMA: Yes / No, Panel Upgrade: Yes / No 0 Plumbing/Mechanical/Electrical Only: 11 Other: APPLICANT (PRIMARY) Name: Kimberly A. Krenek, AlA Address: 6520 Nancy Ridge Drive City: Scn Diego State:CA Zip: 92121 Phone: 858-558-5935 Email: kimberly@krenekdesign.com DESIGN PROFESSIONAL Name: Kimberly A. Krenek, AlA Address: 6520 Nancy Ridge Drive City: San Diego State: CA Zip: 92121 Phone: 858-558-5935 Email: kimberly@krenekdesign.com Architect State License: C 26786 PROPERTY OWNER Name: P2r C-/s2aed Address: S;.'S City:14a- State: ó4 Zip: );7-5- Phone: to 1S 2:5'O 9 Email: ( diiiep. rtaJ CONTRACTOR BUSINESS Narne:411pJ JI)j C, Address: IOO )4j fLJ(_J*prv' \'V State:C3Zip: S lOul Phone: (Y? i9 c— State License')b" 64;q Bus. License:5 (Sec. 7031.5 Business and Professions Code: Any City or County which requires a permit to construct, alter, Improve, demolish or repair any structure, prior to its Issuance, also requires the applicant for such permit to file a signed statement that he/she Is licensed pursuant to the provisions of the Contractor's License Law (Chapter 9, commending with Section 7000 of Division 3 of the Business and Professions Code} or that he/she Is exempt therefrom, and the basis for the alleged exemption. Any violation of Section 7031.5 by any applicant for a permit subjects the applicant to a civil penalty of not more than five hundred dollars ($500)). 1635 Faraday Ave Carlsbad, CA 92008 Ph: 760-602-2719 Fax: 760-602-8558 Email: Buildingcarlsbadca.gov B-2 Page 1 of 2 Rev. 06/18 (OPTION A): WORKERS'COMPENSATION DECLARATION: I hearby affirm under penalty of perjury one of the following declarations: Di have and will maintain a certificate of consent to self-insure for workers' compensation provided by Section 3700 of the Labor Code, for the performance of the work which this permit is issued. have and will maintain worker's compensation, as required by Section 3700 of the Labor Code, for the performance of the work for which this permit is issued. My workers' compensation insurance carrier and policy number are: Insurance Coppaçy Name: I 'tJ i)QA-.-t. Ci Ik' iAit5' Policy No. L_)5ç) 5C3 O Expiration Date: O Certificate of Exemption: I certify that in the performance of the work for which this permit is issued, I shall not employ any person in any manner so as to be come subject to the workers' compensation Laws of California. WARNING: Failure to u workers compensation coverage Is unlawful, and shall subject an employer to criminal penalties and civil fines up to $100,000.00, in addition the to4bt( pensation, damages as provided for In Section 3706 of the Labor Code, Interest and attorney's fees. CONTRACTOR DAGENT DATE: (OPTION B): OWNER-BUILDER DECLARATION: I hereby affirm that I am exempt from Contractor's License Law for the following reason: 0 I, as owner of the property or my employees with wages as their sole compensation, will do the work and the structure is not intended or offered for sale (Sec. 7044, Business and Professions Code: The Contractor's License Law does not apply to an owner of property who builds or improves thereon, and who does such work himself or through his own employees, provided that such improvements are not Intended or offered for sale. If, however, the building or improvement is sold within one year of completion, the owner-builder will have the burden of proving that he did not build or improve for the purpose of sale). 0 I, as owner of the property, am exclusively contracting with licensed contractors to construct the project (Sec. 7044, Business and Professions Code: The Contractor's License Law does not apply to an owner of property who builds or improves thereon, and contracts for such projects with contractor(s) licensed pursuant to the Contractor's License Law). 0 I am exempt under Section Business and Professions Code for this reason: I personally plan to provide the major labor and materials for construction of the proposed property Improvement. 0 Yes 0 No I (have/ have not) signed an application for a building permit for the proposed work. I have contracted with the following person (firm) to provide the proposed construction (Include name address/ phone/ contractors' license number): 4.1 plan to provide portions of the work, but I have hired the following person to coordinate, supervise and provide the major work (include name/ address / phone / contractors' license number): S. I will provide some of the work, but I have contracted (hired) the following persons to provide the work Indicated (include name / address / phone/ type of work): OWNER SIGNATURE: DAGENT DATE:____________ CONSTRUCTION LENDING AGENCY, IF ANY: I hereby affirm that there is a construction lending agency for the performance of the work this permit is issued (Sec. 3097 (i) Civil Code). Lender's Name: Lender's Address: ONLY COMPLETE THE FOLLOWING SECTION FOR NONRESIDENTIAL BUILDING PERMITS ONLY: Is the applicant or future building occupant required to submit a business plan, acutely hazardous materials registration form or risk management and prevention program under Sections 25505, 25533 or 25534 of the Presley-Tanner Hazardous Substance Account Act? Dyes 0 No Is the applicant or future building occupant required to obtain a permit from the air pollution control district or air quality management district? 0 Yes 0 No Is the facility to be constructed within 1,000 feet of the outer boundary of a school site? DYes 0 No IF ANY OF THE ANSWERS ARE YES, A FINAL CERTIFICATE OF OCCUPANCY MAY NOT BE ISSUED UNLESS THE APPLICANT HAS MET OR IS MEETING THE REQUIREMENTS OF THE OFFICE OF EMERGENCY SERVICES AND THE AIR POLLUTION CONTROL DISTRICT. I certify that I have read the application and state that the above information Is correct and that the information on the plans is accurate. I agree to comply with all City ordinances and State laws relating to building construction. I hereby authorize representative of the City of Carlsbad to enter upon the above mentioned property for inspection purposes. I ALSO AGREE TO SAVE, INDEMNIFY AND KEEP HARMLESS THE CITY OF CARLSBAD AGAINST ALL LIABILITIES, JUDGMENTS, COSTS AND EXPENSES WHICH MAY IN ANY WAY ACCRUE AGAINST SAID CITY IN CONSEQUENCE OF THE GRANTING OF THIS PERMIT.OSHA: An OSHA permit Is required for excavations over 5,0' deep and demolition or construction of structures over 3 stories in height. EXPIRATION: Every permit issued by the Building Official under the provisions of this Code shall expire by limitation and become null and void if the building or work authorized by such permit Is not commenced within 180 daysjroi iheciate f such permit or If the building or work authorized by such permit Is suspended or abandoned at any time after the work is commenced fora period of 180lays(Sediois406.4.4 Uniform Building Code). APPLICANT SIGNATURE: '7 c-7 - DATE: _3/ / /9 1635 Faraday Ave Carlsbad, CA 92008 Ph: 760-602-2719 Fax: 760- 2-8558 Email: BufldingccarIsbadca.EoV B-2 Page 2 of 2 Rev. 06/18 Permit Type: BLDG-Commercial Application Date: 94/05/2019 Owner: P D G CARLSBAD 59 LIMITED Work Class: Tenant Improvement Issue Date: 05/30/2019 Subdivision: CARLSBAD TCT#85-24 UNIT#04 Status: Closed - Finaled Expiration Date: 05/26/2020 Address: 1900 ASTON AVE, # 100 IVR Number: 18150 CARLSBAD, CA 92008-7308 Scheduled Actual Inspection Type Inspection No. Inspection Primary Inspector Reinspection Inspection Date Start Date Status Checklist Item COMMENTS Passed BLDG-Building Deficiency May 1, 2020: No Final inspection walk-through completed. Required documentation and information pending; Air balance report, approved• stamped/signed-city plans, inspection• record card, and final fire approval sign-off per Fire Rep. Informed Steve superintendent your tenant improvement project. BLDG-Structural Final . May 1, 2020: . . .. No Final inspection walk-through completed. Required documentation and information pending; Air balance report, approved stamped/signed-city plans, inspection record card, and final fire approval sign-off per Fire Rep. Informed Steve superintendent your tenant improvement project. BLDG-Fire Final - 126032-2020 Passed FeIixSaIcedo Complete Checklist Item COMMENTS Passed FIRE- Building Final Yes 0510812020 05/08/2020 BLDG-Final Inspection -126964-2020 Passed Tony Alvarado Complete Checklist Item COMMENTS Passed BLDG-Plumbing Final May 8, 2020- Yes final inspection completed and approved. Mechanical-Air balance report reviewed and filed City documents. Rest of tenant improvement scope of work OK Tenant improvement signed off also by fire inspector completed and approved BLDG-Mechanical Final May 8, 2020- - Yes final inspection completed and approved. Mechanical-Air balance report reviewed and filed City documents. Rest of tenant improvement scope of work OK. Tenant improvement signed off also by fire inspector completed and approved. BLDG-Structural Final May 8, 2020- Yes final inspection completed and approved. Mechanical-Air balance report reviewed and filed City documents. Rest of tenant improvement scope of work OK. Tenant improvement signed off also by fire inspector completed and approved. Friday, May 8, 2020 - . Page 4 of 5 Permit Type: BLDG-Commercial Application Date: 04/05/2019 Owner: P D G CARLSBAD 59 LIMITED Work Class: Tenant Improvement Issue Date: 05/30/2019 Subdivision: CARLSBAD TCT#85-24 UNIT#04 Status: Closed - Finaléd Expiration Date: 05/26/2020 Address: 1900 ASTON AVE # 100 IVR Number: 18150 CARLSBAD, CA 92008-7308 Scheduled Actual Inspection Type Inspection No. Inspection Primary Inspector Reinspection Inspection Date Start Date Status 0912612019 09/2612019 BLDG-Fire Final 104173-2019 - Withdrawn Felix Salcedo Reinspection Incomplete Checklist Item COMMENTS Passed FIRE- Building Final Yes 11/18I2019 11/18/2019 BLDG-15 Roof/ReRoof 111161-2019 Failed Michael Collins Reinspection Incomplete (Patio) Checklist Item COMMENTS Passed BLDG-Building Deficiency Wrong code No BLDG-Building Deficiency Skylight framing not per plan. No 11I19/2019 11/19/2019 BLDG-14 111600-2019 Partial Pass Paul Burnette Reinspection Incomplete Frame/Steel/Bolting!We Iding (Decks) Checklist Item COMMENTS Passed BLDG-Building Deficiency No 11/22I2019 11/22/2019 BLDG-14 111898-2019 Partial Pass Michael Collins Reinspection Incomplete Frame/Steel/Bolting/We Iding (Decks) Checklist Item COMMENTS Passed BLDG-Building Deficiency Skylight well framing. Need bracing Yes installed per plan. See card. 1112512019 11/25/2019 BLDG-85T-Bar, Ceiling 111922-2019 Passed Paul York Complete Grids, Overhead Checklist Item COMMENTS Passed BLDG-Building Deficiency Yes BLDG-14 Yes Frame-Steel-Bolting-Welding (Decks) BLDG-24 Rough-Topout Yes BLDG-34 Rough Electrical Yes BLDG-44 Yes Rough-Ducts-Dampers 05101I2020 05/01/2020 BLDG-Final Inspection 126338-2020 Failed Tony Alvarado Reinspection Incomplete Friday, May 8, 2020 Page 3 of 5 Permit Type: BLDG-Commercial Application Date: 04/05/2019 Owner: P D G CARLSBAD 59 LIMITED Work Class: Tenant Improvement Issue Date: 05/30/2019 Subdivision: CARLSBAD TCT#85-24UNIT#04 Status: Closed - Finaled Expiration Date: 05126/2020 Address: 1900 ASTON AVE # 100 IVR Number: 18150 CARLSBAD, CA 92008-7308 Scheduled Actual Inspection Type Inspection No. Inspection Primary Inspector Reinspection Inspection Date Start Date Status Checklist Item COMMENTS Passed BLDG-Building Deficiency Yes BLDG-14 Yes Frame-Steel-Bolting-Welding (Decks) BLDG-24 Rough-Topout Yes BLDG-34 Rough Electrical Yes BLDG-44 Yes Rough-Ducts-Dampers 0611712019 0611712019 BLDG-14 094816-2019 Partial Pass Paul Burnette Reinspection Incomplete Frame/Steel/Bolting/We Iding (Decks) Checklist Item COMMENTS Passed BLDG-Building Deficiency No 06I19/2019 06/19/2019 BLDG-17 Interior 095038-2019 Passed Paul Burnette Complete Lath/Drywall - - Checklist Item COMMENTS Passed BLDG-Building Deficiency . Yes 07/1212019 07,12,2019 BLDG-85 1-Bar, Ceiling 097325-2019 Failed Paul Burnette Reinspection Incomplete Grids, Overhead Checklist Item COMMENTS Passed BLDG-Building Deficiency . No BLDG-14 . No Frame-SteeIBolting-WeIding (Decks) BLDG-24 Rough-Topout No BLDG-34 Rough Electrical. No BLDG-44 No Rough-Ducts-Dampers 0711512019 07/15/2019 BLDG-85T-Bar, Ceiling 097541-2019 Passed Paul Burnette Complete Grids, Overhead Checklist Item COMMENTS Passed BLDG-Building Deficiency Yes BLDG-14 Yes Frame-Steel-Bolting-Welding (Decks) BLDG-24 Rough-Topout Yes BLDG-34 Rough Electrical Yes BLDG-44 Yes Rough-Ducts-Dampers 09/12/2019 09/12/2019 BLDG-Fire Final 103506-2019 Failed Felix Salcedo - Reinspection Incomplete Checklist Item COMMENTS . Passed FIRE- Building Final . No Friday, May 8, 2020 Page 2 of 5 Building Permit Inspection History Finaled (ity of Carlsbad Permit Type: BLDG-Commercial Application Date: 04/05/2019 Owner: P D G CARLSBAD 59 LIMITED Work Class: Tenant Improvement Issue Date: 05/30/2019 Subdivision: CARLSBAD TCT#85-24 UNiT#04 Status: Closed - Finaled Expiration Date: 05/26/2020 Address: 1900 ASTON AVE. # 100 IVR Number: 18150 CARLSBAD, CA 92008-7308 Scheduled Actual Inspection Type Inspection No. Inspection Primary Inspector Reinspection Inspection Date Start Date Status 05131/2019 05/31/2019 BLDG-44 093337-2019 Passed Paul Burnette Complete Rough/Ducts/Dampers Checklist Item COMMENTS Passed BLDG-Building Deficiency Yes BLDG-81 Underground 093336-2019 Passed Paul Burnette Complete Combo(11,12,21,31) Checklist Item COMMENTS Passed BLDG-Building Deficiency Yes BLDG-11 Foundation-Ftg-Piers Yes (Reber) BLDG-12 Steel-Bond Beam Yes BLDG-21 Yes Underground-Underfloor Plumbing BLDG-31 Yes Underground-Conduit Wiring 06104/2019 06/0412019 BLDG-15 Roof/ReRoof 093640-2019 Failed Andy Krogh Reinspection Incomplete (Patio) Checklist Item COMMENTS Passed BLDG-Building Deficiency Wrong code No BLDG-84 Rough 093804-2019 Partial Pass Andy Krogh Reinspection Incomplete Cornbo(I4,24,34,44) - - Checklist Item COMMENTS Passed BLDG-Building Deficiency As noted on card Yes BLDG-14 Yes Frame-Steel-Bolting-Welding (Decks) BLDG-24 Rough-Topout Yes BLDG-34 Rough Electrical - Yes BLDG-44 Yes Rough-Ducts-Dampers 06I12/2019 06/12/2019 BLDG-85 T-Bar, Ceiling 094408-2019 Passed Paul Burnette Complete Grids, Overhead Friday, May 8, 2020 Page I of 5 EsGil' A SAFEbuittCompany DATE: MAY 20, 2019 JURISDICTION: CARLSBAD PLAN CHECK #.: CBC 2019-0155 SET: II PROJECT ADDRESS: 1900 ASTON AVENUE PROJECT NAME: M2 INGREDIENTS T.I. U APPLICANT U JURIS. The plans transmitted herewith have been corrected where necessary and substantially comply with the jurisdiction's building codes. ü The plans transmitted herewith will substantially comply with the jurisdiction's codes when minor deficiencies identified below are resolved and checked by building department staff. The plans transmitted herewith have significant deficiencies identified on the enclosed check list and should be corrected and resubmitted for a complete recheck. 1111 The check list transmitted herewith is for your information. The plans are being held at EsGil until corrected plans are submitted for recheck. The applicant's copy of the check list is enclosed for the jurisdiction to forward to the applicant contact person. Lull The applicant's copy of the check list has been sent to: EsGil staff did not advise the applicant that the plan check has been completed. LI EsGil staff did advise the applicant that the plan check has been completed. Person contacted: KIM KRENEK, AlA Telephone #: 858-558-5935 Date contacted: (by: ) Email: kimberly(äkrenekdesiqn.com Mail Telephone Fax In Person REMARKS: This T. I. is on the 1st floor and one control area only. There are a total of two control areas in the building. By: ALl SADRE, S.E. Enclosures: EsGil 5/13 9320 Chesapeake Drive, Suite 208 • San Diego, California 92123 • (858) 560-1468 • Fax (858) 560-1576 EsGil A.SAFEbuitt'Company DATE: JURISDICTION: CARLSBAD PLAN CHECK #.: 2O1i55J PROJECT ADDRESS: 1900 ASTON AVENUE U APPLICANT U JURIS. PROJECT NAME: M2 INGREDIENTS T.I. E The plans transmitted herewith have been corrected where necessary and substantially comply with the jurisdiction's codes. The plans transmitted herewith will substantially comply with the jurisdiction's codes when minor deficiencies identified below are resolved and checked by building department staff. The plans transmitted herewith have significant deficiencies identified on the enclosed check list and should be corrected and resubmitted for a complete recheck. The check list transmitted herewith is for your information. The plans are being held at EsGil until corrected plans are submitted for recheck. The applicant's copy of the check list is enclosed for the jurisdiction to forward to the applicant contact person. The applicant's copy of the check list has been sent to: EsGil staff did not advise the applicant that the plan check has been completed. EsGil staff did advise the applicant that the plan check has been completed. Person contacted: KIM KRENEK, AlA Telephone #: 858-558-5935 Date contacted: (by: ) Email: kimberlyäkrenekdesiqn.com Mail Telephone Fax In Person REMARKS: controLareasJnih&build ma. By: ALl SADRE, S.E. Enclosures: EsGil 4/09 9320 Chesapeake Drive, Suite 208 • San Diego, California 92123 • (858) 560-1468 • Fax(858)560-1576 CARLSBAD CBC 2019-0155 APR. 179 2019 GENERAL PLAN CORRECTION LIST JURISDICTION: CARLSBAD PLAN CHECK #.: CBC 2019-0155 PROJECT ADDRESS: 1900 ASTON AVENUE CONST. = V-B; STORIES = TWO; SPRINKLERS = YES; HEIGHT = NO CHANGE AREA = THIS T.I. = 12,606; BLDG. AREA = 43,443; OCCUPANCY = B/Fl/SI DATE PLAN RECEIVED BY DATE REVIEW COMPLETED: ESGIL: 4/09 APR. 17, 2019 REVIEWED BY: ALl SADRE, S.E. FOREWORD (PLEASE READ): This plan review is limited to the technical requirements contained in the International Building Code, Uniform Plumbing Code, Uniform Mechanical Code, National Electrical Code and state laws regulating energy conservation, noise attenuation and disabled access. This plan review is based on regulations enforced by the Building Department. You may have other corrections based on laws and ordinances enforced by the Planning Department, Engineering Department or other departments. The following items listed need clarification, modification or change. All items must be satisfied before the plans will be in conformance with the cited codes and regulations. The approval of the plans does not permit the violation of any state, county or city law. GENERAL 1. Please make all corrections, as requested in the correction list. Submit FOUR new complete sets of plans for commercial/industrial projects (THREE sets of plans for residential projects). For expeditious processing, corrected sets can be submitted in one of two ways: I. Deliver all corrected sets of plans and calculations/reports directly to the City of Carlsbad Building Department, 1635 Faraday Ave., Carlsbad, CA 92008, (760) 602-2700. The City will route the plans to EsGil and the Carlsbad Planning, Engineering and Fire Departments. 2. Bring TWO corrected set of plans and calculations/reports to EsGil, 9320 Chesapeake Drive, Suite 208, San Diego, CA 92123, (858) 560-1468. Deliver all remaining sets of plans and calculations/reports directly to the City of Carlsbad Building Department for routing to their Planning, Engineering and Fire Departments. NOTE: Plans that are submitted directly to EsGil only will not be reviewed by the City Planning, Engineering and Fire Departments until review by EsGil is complete. CARLSBAD CBC 2019-0155 APR. 17, 2019 To facilitate rechecking, please identify, next to each item, the sheet of the plans upon which each correction on this sheet has been made and return this sheet with the revised plans. Please indicate here if any changes have been made to the plans that are not a result of corrections from this list. If there are other changes, please briefly describe them and where they are located on the plans. Have changes been made not resulting from this list? U Yes U No PLANS Please note the site plans is for reference only, otherwise, provide sheets A9 & Al 1, with the details referenced on the site plans. Provide a note on the plans indicating if any hazardous materials will be stored and/or used within the building which exceed the quantities listed in IBC Tables 307.1(1) and 307.1(2). On Sheet A2. 1, please clarify keynote #5, as called out at doors #124B & C, 13013, 13413, 13813, etc. Show, or note, that an additional sign shall also be posted in a conspicuous place at each entrance to off street parking facilities, or immediately adjacent to and visible from each stall or space. Section 11 B-502.8.2. The sign shall be ~:l 7" x 22" with lettering not :5l" in height. The required wording is as follows. "Unauthorized vehicles parked in designated accessible spaces not displaying distinguishing placards or SPECIAL license plates issued for persons with disabilities may be towed away at owner's expense. Towed vehicles may be reclaimed at or by telephoning ." The word "Special" is left out on detail 3/A 10.0. Show that detectable warnings, 36" deep and extending the full width of the curb ramp, are to be installed for all curb ramps (regardless of slope), per Section 1113- 705. Only approved DSNAC detectable warning products and directional surfaces shall be installed. Section 11 B-705.3. This is noted as 4', on the site plans. The curb ramps shall be located so that they do not project into vehicular traffic lanes, parking spaces, or parking access aisles. Sec. 11 B-406.5. 1. Correct detail 1/A10.0, as required. Show compliance with CBC, Sec. 11 B-705.1.1.3, specifically the color of the detectable warnings. Detectable warning surfaces shall be yellow & approximate FS 33538 of Federal Standard 595C. The urinal minimum projection shall be 131/2 ', as opposed to 12", as noted on 14- D/AI0.0 (top detail-plan view). Sec. 11 B-605.2. Please specify 34" for the HC accessible door compartment on detail 16/AI0.0. Sec. 11 B-604.8.1.2. CARLSBAD CBC 2019-0155 APR. 17, 2019 On Sheet A2.3, please state that all HVAC units are existing. Currently, units 14, 17, 18, 19, 20, 21 & 22 are not listed as (E). MISCELLANEOUS Please see attached for P/M/E corrections. The jurisdiction has contracted with EsGil, located at 9320 Chesapeake Drive, Suite 208, San Diego, California 92123; telephone number of 858/560-1468, to perform the plan review for your project. If you have any questions regarding these plan review items, please contact ALl SADRE, S.E. at EsGil. Thank you. PLUMBING AND MECHANICAL COMMENTS PLAN REVIEW NUMBER: cbc2019-0155 SET: I PLAN REVIEWER: Connor Reuss PLUMBING (2016 CALIFORNIA PLUMBING CODE) Please review the prosed vent sizing for the entire building. For each drainage piping system connected to the public sewer that is vented by one or more vent pipes, the combination of the cross-sectional area of all vents that terminate through the roof cannot be less than the cross-sectional area of the largest waste pipe in the drainage system (in this case 4" waste pipe). Note: The cross- sectional area of a 4" diameter waste pipe is 12.57". The cross-sectional area of 2" diameter vent pipe is 3.14". CIVIC 904.1 Please elaborate on the outside floor sink shown on sheet P3. What is it used for? It appears storm water may impact the sewer system through this floor sink. Please address. Please show the size of all water lines on sheet P4. All domestic hot water piping to have the following minimum insulation installed: 1/2" pipe (1/2" insulation); %" pipe (1" insulation); 1"-1 1/2" pipe (1 1A" insulation). CPC 609.11 & ES 150.00) Specify if any natural gas-powered appliances are under this permit. If so, please provide the proper CPC 1216.2 Table, the total developed length, and the load for each appliance. CPC 1216.0 Please specify if the air compressor is new or existing. If existing, please provide the manufacture's installation instructions upon next submittal. The P&T routing between the detail on sheet P1 and the remarks section within the schedule on sheet P1 are inconsistent. Please correct. For the hot water recirculating loop system, please detail the following: Specify the circulation pump within the schedule on sheet P1. CARLSBAD CBC 2019-0155 APR. 17, 2019 The installation of an air release valve on the inlet side of the recirculation pump, within 4' of the pump. A check valve is required between the recirculating pump and the water heating equipment to prevent the hot water from flowing backwards through the recirculation loop. Show the required pump isolation valves for the recirculation pump per Energy Standard 110.3(c) MECHANICAL (2016 CALIFORNIA MECHANICAL CODE) Please correct the title of sheet M3.1. Specify if any rooms are to store chemicals. If so, an exhaust system complying to the exhaust rate specified within CIVIC Table 403.7 is required. Note: If you have any questions regarding this Plumbing and Mechanical plan review list please contact Connor Reuss at (858) 560-1468. To speed the review process, note on this list (or a copy) where the corrected items have been addressed on the plans. ELECTRICAL, and ENERGY COMMENTS PLAN REVIEWER: Morteza Beheshti ELECTRICAL (2016 CALIFORNIA ELECTRICAL CODE) Egress (emergency back-up) lighting is required for exterior landings of required exit doors/exterior stairways located at other than the level of exit discharge. Please add to the plans. The lighting plans require completed design for the large area. ENERGY (2016 CALIFORNIA BUILDING ENERGY STANDARDS) Provide controlled receptacle outlets in offices. Each floor, each space (not exceeding 5,000 square feet), and each type (general, display, and ornamental) of lighting shall be individually capable of being automatically shut-off when the building is unoccupied. Include the control design. Automatic time switch control requires a 2 hour override. ES 130.1(c) Occupancy controls are required to shut off all lighting in: Offices 250 square feet or smaller, multipurpose rooms of less than 1,000 square feet, conference rooms, and classrooms of any size. ES 130.1(c)5 Lighting installed in corridors and stairwells shall be controlled by occupant sensing controls that separately reduce the lighting power by at least 50% when the space is unoccupied. ES 130.1c (6) C. CARLSBAD CBC 2019-0155 APR. 179 2019 31. Generally, automatic daylighting control with multilevel lighting ability is required for general lighting in daylit zones. Please provide the locations and control design. ES 130.1(d) Be sure to review the following two exceptions for project applicability: . Rooms that do not require automatic daylighting: Rooms with no more than 120 watts of lighting in the skylit and primary sidelit zones combined. Rooms with less than 24 square feet of glazing. Note: If you have any questions regarding this Electrical and Energy plan review list please contact Morteza Beheshti mbeheshtiesqil.com OR at (858) 560-1468. To speed the review process, note on this list (or a copy) where the corrected items have been addressed on the plans. S CARLSBAD CBC 2019-0155 APR. 17, 2019 [DO NOT PAY— THIS IS NOTAN INVOICE] VALUATION AND PLAN CHECK FEE JURISDICTION: CARLSBAD PLAN CHECK #.: CBC 2019-0155 PREPARED BY: ALl SADRE, S.E. DATE: APR. 179 2019 BUILDING ADDRESS: 1900 ASTON AVENUE BUILDING OCCUPANCY: B/Fl/Si; V-B/SPR. BUILDING AREA Valuation PORTION (Sq. Ft.) Multiplier T.I. 12606 Reg. Mod. VALUE ($) Air Conditioning Fire Sprinklers TOTAL VALUE 586,305 Jurisdiction Code CB By Ordinance 1997 UBC Building Permit Fee 1997 UBC Plan Check Fee V Type of Review: 0 Complete Review o Structural Only Repetitive Fee v1 Repeats O Other Hourly EsGil Fee Hr. © * $1,401.94 Comments: Sheet 1 of 1 SAN DIEGO REGIONAL I OFFICE USE ONLY - HAZARDOUS MATERIALS IPLAN IRECORD ID#_______________________________ CHECK #_________________ QUESTIONNAIRE I BID DATE F Business Name Business Contact Telephone I M2 Ingredients, Inc David Crist 866-740-6874 tProject Address Csbad C Zip Code 920Q8te I APN# 1 1900 Aston Avenue [Mailing Address City State Zip Code I Plan File# 15931 Priestly Drive, Ste. 101 Carlsbad CA 92008 1 Project Contact Applicant E-mail Telephone # I Kimberly A. Krenek, AlA kimberly©krenekdesign.com 858-558-5935 The following questions represent the facility's activities, NOT the specific project description. PART : FIRE DEPARTMENT— HAZARDOUS MATERIALS DIVISION: OCCUPANCY CLASSIFICATION: that rattuired for rirofocts wlhintho City of n Dieao: indicate by circling the item, whether your business will use, process, or store any of the following hazardous materials. if any of the items are circled. applicant must contact the Fire Protection Agency with jurisdiction prior to plan submittal. Occupancy Rating: Facility's Square Footage (including proposed project): Explosive or Blasting Agents 5. Organic Peroxides 9. Water Reactives 13. Corrosives Compressed Gases 6. Oxidizers 10. Cryogenics 14. Other Health Hazards Flammable/Combustible Liquids 7. Pyrophorics 11. Highly Toxic or Toxic Materials 15. None of These. Flammable Solids 8. Unstable Reactives 12. Radloactives 1 the ans to any Diego, CA 92123. Call (858) 505-6700 prior to the issuance of a building permit. FEES ARE REQUIRED Project Completion Date: Expected Date of Occupancy: YES NO (for new construction or remodeling projects) 0 &I Is your business listed on the reverse side of this form? (check all that apply). 0 Will your business dispose of Hazardous Substances or Medical Waste in any amount? 0 Will your business store or handle Hazardous Substances In quantities greater than or equal to 55 gallons, 500 pounds and/or 200 cubic feet? 0 Will your business store or handle carcinogens/reproductIve toxins in any quantity? 0 IJ Will your business use an existing or Install an underground storage tank? 0 Will your business store or handle Regulated Substances (CalARP)? 0 Will your business use or install a Hazardous Waste Tank System (Title 22, Article 10)? 8, 0 II Will your business store petroleum in tanks or containers at your facility with a total facility storage capacity equal to CalARP Exempt Pale Initials CaIARP Required Oats Initials CalARP Complete Dale Initials PART Ill: SAN DIEGO COUNTY AIR POLLUTION CONTROL DISTRICT (APCD: Any YES answer requires a stamp from APCD 10124 Old Grove Road, San Diego, CA 92131 aDcdconp(lsdcounty.cp.pov (858) 586-2650). [-No stamp required if 01 Yes and 03 Yes and Q4-Q6 No]. The following questions are intended to identify the majority of air pollutbn issues at the planning stage. Projects may require additional measures not Identified by these questions. For comprehensive requirements contact APCD. Residences are typically exempt, except - those with more than one building on the property; single buildings with more than four dwelling units; townhomes; condos: mixed-commercial use; deliberate bums; residences forming part of a larger project. rExcludes garages & small outbuildings.] YES NO J 0 Will the project disturb 160 square feet or more of existing building materials? U Will any load supporting structural members be removed? Notification may be required 10 working days prior to commencing demolition. 0 (ANSWER ONLY IF QUESTION 1 or 2 IS YES) Has an asbestos survey been performed by a Certified Asbestos Consultant or Site Surveillance Technician? 4 0 E (ANSWER ONLY IF QUESTION 3 IS YES) Based on the survey results, will the project disturb any asbestos containing material? Notification may be required 10 working days prior to commencing asbestos removal. 0 [ Will the project or associated construction equipment emit air contaminants? See the reverse side of this form or APCD factsheet (www.sdaood.oro/info/factsloermits.odfl for typical equipment requiring an APCD permit. 0 0 (ANSWER ONLY IF QUESTION 5 IS YES) Will the project or associated construction equipment be located within 1.000 feet of a school boundary Briefly describe business activities: One describe ppposed project: Warehousing,blending and packaging of medicinal mushroom produc S Tenfl)Cip9ades to I d property I declare under penalty of perjury that to the best of my knowledge and belief t r ponses C a I__ruroj d correct. David Crist Name of Owner or Authorized Agoni Sil of Owner r Aulhorized AenL - Date FOR OFFICAL USE ONLY: FIRE DEPARTMENT OCCUPANCY CLASSIFICATION:_ BY: DATE: / EXEMPT OR NO FURTHER INFORMATION REQUIRED RELEASED FOR BUILDING PERMIT BUT NOT FOR OCCUPANCY RELEASED roit occupANcy COUNTY-HMD' APCD COUNTY-HMD APCD COUNTY-HMD APCO A stamp In tINs box oniv exempts businesses from completing or upoaling a MazarOous Materials business man. otner permitting requirements may StIll apply. HM-9171 (08/15) County of San Diego — DEN — Hazardous Materials Division ENCIN INDUSTRIAL WASTEWATER DISCHARGE PERMIT WASMAWA SCREENING SURVEY Date_________ Business Name M2 Ingredients, Inc Street Address 900 Aston Avenue, Carlsbad, CA 92008 Email Address kimberIykrenekdesign.com PLEASE CHECK HERE IF YOUR BUSINESS IS EXEMPT: (ON REVERSE SIDE CHECK TYPE OF BUSINESS) Check all below that are present at your facility: Acid Cleaning Ink Manufacturing Nutritional Supplement! Assembly Laboratory Vitamin Manufacturing X Automotive Repair Machining! Milling Painting / Finishing Battery Manufacturing Manufacturing Paint Manufacturing Biofuel Manufacturing Membrane Manufacturing Personal Care Products Biotech Laboratory (i.e. water filter membranes) Manufacturing Bulk Chemical Storage Metal Casting/ Forming Pesticide Manufacturing! Car Wash Metal Fabrication Packaging Chemical Manufacturing Metal Finishing Pharmaceutical Manufacturing Chemical Purification Electroplating (including precursors) Dry Cleaning Electroless plating Porcelain Enameling Electrical Component Anodizing Power Generation Manufacturing Coating (i.e. phosphatlng) Print Shop Fertilizer Manufacturing Chemical Etching / Milling Research and Development Film/X-ray Processing Printed Circuit Board Rubber Manufacturing Food Processing Manufacturing Semiconductor Manufacturing Glass Manufacturing Metal Powders Forming Soap/ Detergent Manufacturing Industrial Laundry Waste Treatment/ Storage SIC Code(s) (if known): 2034, 2099 Brief description of business activities (Production I Manufacturing Operations):______________ Description of operations generating wastewater (discharged to sewer, hauled or evaporated): - Tools, equipment and facility cleaning -Employee usage Estimated volume of industrial wastewater to be discharged (gal /day): 700 gal List hazardous wastes generated (type /volume): None Date operation began/or will begin at this location: May 1,2019 Have you applied for a Wastewater Discharge Permit from the Encina Wastewater Authority? Yes X No if yes, when: February 2016 for Priestly Dr. Ste 101 Carlsbad. location Site Contact Steve Farrar Titie C.T.O. Signature ----- Phone No.866-740-6874 ENCINA WASTEWATR AUTHORITY, 6200 Avenida Encinas Carlsbad, CA 92011 (760) 438-3941 FAX (760) 476.9852 (city of STORM WATER STANDARDS Development Services Carlsbad QUESTIONNAIRE Land Development Engineering 1635 Faraday Avenue E-34 (760) 602-2750 www.carlsbadca.gov INSTRUCTIONS: To address post-development pollutants that may be generated from development projects, the city requires that new development and significant redevelopment priority projects incorporate Permanent Storm Water Best Management Practices (BMPs) into the project design per Carlsbad BMP Design Manual (BMP Manual). To view the BMP Manual, refer to the Engineering Standards (Volume 5). This questionnaire must be completed by the applicant in advance of submitting for a development application (subdivision, discretionary permits and/or construction permits). The results of the questionnaire determine the level of storm water standards that must be applied to a proposed development or redevelopment project. Depending on the outcome, your project will either be subject to STANDARD PROJECT' requirements or be subject to 'PRIORITY DEVELOPMENT PROJECT' (PDP) requirements. Your responses to the questionnaire represent an initial assessment of the proposed project conditions and impacts. City staff has responsibility for making the final assessment after submission of the development application. If staff determines that the questionnaire was incorrectly filled out and is subject to more stringent storm water standards than initially assessed by you, this will result in the return of the development application as incomplete. In this case, please make the changes to the questionnaire and resubmit to the city. If you are unsure about the meaning of a question or need help in determining how to respond to one or more of the questions, please seek assistance from Land Development Engineering staff. A completed and signed questionnaire must be submitted with each development project application. Only one completed and signed questionnaire is required when multiple development applications for the same project are submitted concurrently. PROJECT INFORMATION PROJECT NAME: M2 Ingredients Ti. PROJECTID: ADDRESS: 1900 Aston Ave, Suite 100 APN: 212-120-24-00 The project is (check one): 0 New Development 0 Redevelopment The total proposed disturbed area is: ft2 ( ) acres The total proposed newly created and/or replaced impervious area is: ft2 ( ) acres If your project is covered by an approved SWQMP as part of a larger development project, provide the project ID and the SWOMP # of the larger development project: Project ID Swamp #: Then, go to Step I and follow the instructions. When completed, sign the form at the end and submit this with your application to the city. E-34 Page 1 014 REV 02/16 STEP I TO BE COMPLETED FOR ALL PROJECTS To determine if your project is a "development project", please answer the following question: YES NO Is your project LIMITED TO routine maintenance activity and/or repair/improvements to an existing building or structure that do not alter the size (See Section 1.3 of the BMP Design Manual for guidance)? 117 11 If you answered "yes" to the above question, provide justification below then go to Step 5, mark the third box stating "my project is not a 'development project' and not subject to the requirements of the BMP manual" and complete applicant information. Justification/discussion: (e.g. the project includes only interior remodels within an existing building): Scope of project is limited to interior tenant improvements within an existing building. If you answered "no" to the above question, the project is a 'development project', go to Step 2. STEP 2 TO BE COMPLETED FOR ALL DEVELOPMENT PROJECTS To determine if your project is exempt from PDP requirements pursuant to MS4 Permit Provision E.3.b.(3), please answer the following questions: Is your project LIMITED to one or more of the following: YES NO 1. Constructing new or retrofitting paved sidewalks, bicycle lanes or trails that meet the following criteria: Designed and constructed to direct storm water runoff to adjacent vegetated areas, or other non- erodible permeable areas; Designed and constructed to be hydraulically disconnected from paved streets or roads; C) Designed and constructed with permeable pavements or surfaces in accordance with USEPA Green Streets guidance? 2. Retrofitting or redeveloping existing paved alleys, streets, or roads that are designed and constructed in o 0 accordance with the USEPA Green Streets guidance? 3. Ground Mounted Solar Array that meets the criteria provided in section 1.4.2 of the BMP manual? 0 0 If you answered "yes" to one or more of the above questions, provide discussion/justification below, then go to Step 5, mark the second box stating "my project is EXEMPT from PDP ..." and complete applicant information. Discussion to justify exemption (e.g. the project redeveloping existing road designed and constructed in accordance with the USEPA Green Street guidance): If you answered "no" to the above questions, your project is not exempt from PDP, go to Step 3. E-34 Page of 4 REV 04117 STEP 3 TO BE COMPLETED FOR ALL NEW OR REDEVELOPMENT PROJECTS To determine if your project is a PDP, please answer the following questions (MS4 Permit Provision E.3.b.(1)): YES NO Is your project a new development that creates 10,000 square feet or more of impervious surfaces collectively over the entire project site? This includes commercial, industrial, residential, mixed-use, 0 0 and public development projects on public or private land. Is your project a redevelopment project creating and/or replacing 5,000 square feet or more of impervious surface collectively over the entire project site on an existing site of 10,000 square feet or Cl 11 more of impervious surface? This includes commercial, industrial, residential, mixed-use, and public development projects on public or private land. Is your project a new or redevelopment project that creates and/or replaces 5,000 square feet or more of impervious surface collectively over the entire project site and supports a restaurant? A restaurant is a facility that sells prepared foods and drinks for consumption, including stationary lunch counters and 0 0 refreshment stands selling prepared foods and drinks for immediate consumption (Standard Industrial Classification (SIC) code 5812). Is your project a new or redevelopment project that creates 5,000 square feet or more of impervious surface collectively over the entire project site and supports a hillside development project? A hillside 0 El development project includes development on any natural slope that is twenty-five percent or greater. Is your project a new or redevelopment project that creates and/or replaces 5,000 square feet or more of impervious surface collectively over the entire project site and supports a parking lot? A parking lot is 11 0 a land area or facility for the temporary parking or storage of motor vehicles used personally for business or for commerce. Is your project a new or redevelopment project that creates and/or replaces 5,000 square feet or more of impervious Street, road, highway, freeway or driveway surface collectively over the entire project 1:1 El site? A street, road, highway, freeway or driveway is any paved impervious surface used for the transportationof automobiles, other vehicles. _trucks, _motorcycles, _and Is your project a new or redevelopment project that creates and/or replaces 2,500 square feet or more of impervious surface collectively over the entire site, and discharges directly to an Environmentally Sensitive Area (ESA)? ffDischarging Directly to" includes flow that is conveyed overland a distance of 0 CI 200 feet or less from the project to the ESA, or conveyed in a pipe or open channel any distance as an isolated flow from the project to the ESA (i.e. not commingled with flows from adjacent lands). * Is your project a new development or redevelopment project that creates and/or replaces 5,000 square feet or more of impervious surface that supports an automotive repair shop? An automotive repair 11 El shop is a facility that is categorized in any one of the following Standard Industrial Classification (SIC) codes: 5013, 5014, 5541, 7532-7534, or 7536-7539. Is your project a new development or redevelopment project that creates and/or replaces 5,000 square feet or more of impervious area that supports a retail gasoline outlet (RGO)? This category includes RGO's that meet the following criteria: (a) 5,000 square feet or more or (b) a project Average Daily Traffic (ADT) of 100 or more vehicles per day. Is your project a new or redevelopment project that results in the disturbance of one or more acres of land and are expected to generate pollutants post construction? Is your project located within 200 feet of the Pacific Ocean and (1) creates 2,500 square feet or more of impervious surface or (2) increases impervious surface on the property by more than 10%? (CMC 0 CI 21.203.040) If you answered "yes" to one or more of the above questions, your project is a POP. If your project is a redevelopment project, go to step 4. If your project is a new project, go to step 5, check the first box stating "My project is a PDP ..." and complete applicant information. If you answered "no" to all of the above questions, your project is a 'STANDARD PROJECT.' Go to step 5, check the second box stating "My project is a 'STANDARD PROJECT'..." and complete applicant information. E-34 Page 3 of 4 REV 04/17 STEP 4 TO BE COMPLETED FOR REDEVELOPMENT PROJECTS THAT ARE PRIORITY DEVELOPMENT PROJECTS (PDP) ONLY Complete the questions below regarding your redevelopment project (MS4 Permit Provision E.3.b.(2)): YES NO Does the redevelopment project result in the creation or replacement of impervious surface in an amount of less than 50% of the surface area of the previously existing development? Complete the percent impervious calculation below: Existing impervious area (A) = sq. ft. 0 0 Total proposed newly created or replaced impervious area (B) = ___sq. ft. Percent impervious area created or replaced (B/A)*100 = % If you answered eyes", the structural BMPs required for PDP apply only to the creation or replacement of impervious surface and not the entire development. Go to step 5, check the first box stating "My project is a PDP ..." and complete applicant information. If you answered uflO the structural BMP's required for POP apply to the entire development. Go to step 5, check the check the first box stating uMy project is a PDP ..." and complete applicant information. STEP 5 CHECK THE APPROPRIATE BOX AND COMPLETE APPLICANT INFORMATION O My project is a PDP and must comply with PDP stormwater requirements of the BMP Manual. I understand I must prepare a Storm Water Quality Management Plan (SWQMP) for submittal at time of application. O My project is a 'STANDARD PROJECT' OR EXEMPT from POP and must only comply with 'STANDARD PROJECT' stormwater requirements of the BMP Manual. As part of these requirements, I will submit a "Standard Project Requirement Checklist Form E-36" and incorporate: low impact development strategies throughout my project. Note: For projects that are close to meeting the POP threshold, staff may require detailed impervious area calculations and exhibits to verify if 'STANDARD PROJECT' stormwater requirements apply. My Project is NOT a 'development project' and is not subject to the requirements of the BMP Manual. Applicant Information and Signature Box Applicant Name: fsiE Applicant Title: Applicant Signature: (2. /:,Cf_- Data: environmentaiiy ensmve areas incivae out are not ulmitea to an uean water ACt tiection i0i(0) impaired water Dodies; areas designated as Areas of Special Biological Significance by the State Water Resources Control Board (Water Quality Control Plan for the San Diego Basin (1994) and amendments); water bodies designated with the RARE beneficial use by the State Water Resources Control Board (Water Quality Control Plan fbr the San Diego Basin (1994) and amendments); areas designated as preserves or their equivalent under the Multi Species Conservation Program within the Cities and County of San Diego; Habitat Management Plan; and any other equivalent environmentally sensitive areas which have been identified by the City. This Box for ON Use Only City Concurrence: YES NO El By: Date: Project ID: E-34 Page 4of4 REV 04/17 F1L. cL - (' (I - 1L. r:: 4 - .' - - ri2 . (0— 2 - , NO. 4P8 Exp. md t y. g EoE(2, i-1 :ri 1. 1•' F,x . 2-se !~ut9 1i!Lt.s.5 ri'r c I Cityof PERMIT REPORT Carlsbad Print Date: 05/11/2020 Permit No: PREV2019-0223 Job Address: 1900 Aston Ave, 100 Permit Type: BLDG-Permit Revision Work Class: Commercial Permit Revi5 Status: Closed - Finaled Parcel No: 2121202400 Applied: 10/29/2019 Valuation: $ 0.00 Lot #: Issued: 11/12/2019 Occupancy Group: Project #: PermitFinal # Dwelling Units: Construction Type Close Out: 05/11/2020 Bedrooms: Inspector: PBurn Bathrooms: Orig. Plan Check #: CBC2019-0155 Final Plan Check #: Inspection: Project Title: Description: M2 INGREDIENTS: (2) SMOKE VENTS 64 SF TOTAL (32 SF EACH) Owner: Co-Applicant: P D G CARLSBAD 59 LIMITED KELCHLIN CONSTRUCTION INC 1900 Aston Ave . 13100 Kirkham Way, Ste 201 CARLSBAD, CA 92008 Poway, CA 92064-7128 858-513-3799 FEE AMOUNT BUILDING PLAN CHECK REVISION ADMIN FEE $35.00 FIRE Plan Review Per Hour - Office Hours $136.00 FIRE Plan Review Per Hour - Office Hours $204.00 MANUAL BLDG PLAN CHECK FEE _$225.00 Total Fees: $ 600.00 Total Payments To Date: $ 600.00 Balance Due: $0.00 Building Division 1635 Faraday Avenue, Carlsbad CA 92008-7314 1 760-602-2700 1 760-602-8560 f I www.carlsbadca.gov Page 1 of 1 PLAN CHECK REVISION OR Development Services ('City of DEFERRED SUBMITTAL Building Division Carlsbad APPLICATION 1635 Faraday Avenue 760-602-2719 B-15 www.carlsbadca.gov Original Plan Check Number R (20 1 ° Plan Revision Number ?R 1Vto '1.-o22 Project Address 1900 Aston Ave., Suite 100 Carlsbad, CA 92008 General Scope of Revision/Deferred Submittal: Smoke Ventilation CONTACT INFORMATION: Name_Kelchlin Construction, Inc. Phone (858)_513-3199 Fax 4858)513-3899 Address 13100 Kirkham Way, Suite 201 City _Poway Zip .22084 Email Address j@kelchlinconstruction .com Original plans prepared by an architect or engineer, revisions must be signed & stamped by that person. 1 . Elements revised: L 'Plans EJ Calculations fl Soils fl Energy X Other 2. Describe revisions in detail 3. List page(s) where each revision is shown New 4 x 8' Quasar prismatic acrylic aluminum double lid curb mounted tnarch smoke vent on roof with framing and GYP, skylight well at ceiling level. Per revised high pile storage report dated 10/1712019. A2.3 & A4.1 Does this revision, in any way, alter the exterior of the project? EJ Yes IR No Does this revision add ANY new floor area(s)? fl Yes Does this revision affect any fire related issues? D Yes Is this a complete set? No p1 .I -wzsii 1635 Faraday Avenue, Carlsbad, CA 92008 Eti: 760-602-2719 f: 760-602-8558 Email: building@carlsbadca.gov www.carlsbadca.gov PIR SSS KLAUSBRUCKNER AND ASSOCIATES 2495Truxtun Road, Suite 205 San Diego, CA 92106 October 17, 2019 Tel: (619) 677-2004 Fax: (619) 677-2444 Darcy Davidson, Assistant Fire Marshal R E C E V E 0 Carlsbad Fire Department/Fire Prevention 1635 FaradayAve. 0C12 9 2019 Carlsbad, CA 92008 CITY OF CARLSBAD RE: M2 Ingredients - 1900 Aston Ave., Carlsbad, CA BUILDING DIVISION Addendum to Report Dated March 20, 2019 - Smoke and Heat Vents Dear Ms. Davidson: On behalf of M2 Ingredients, we are requesting approval of an addendum to the High Piled Storage Report dated March 20, 2019 for the above-mentioned M2 Ingredients Warehouse at 1900 Aston Ave. in the City of Carlsbad California. The approved High Piled Storage report specified a mechanical exhaust in lieu of smoke and heat vents due to dropped ceilings proposed within the two storage areas. However the architect of record and structural engineer of record have prepared plans showing compliance with smoke and heat vents in lieu of the originally proposed mechanical exhaust. The following calculations have been done in accordance with CFC Section 910.3 the following calculations are made Per CFC 910.3 (Attachment #10), the design and installation requirement for smoke and heat vents shall be as follows: >2111 Listing and labeling. Smoke and heat vents are required to be listed and labeled to indicate their V11211111 _ compliance with FM 4430, ICC-ED AC 331, or UL 793. ____ Smoke and heat vent locations. Smoke and heat vents shall be located 30 feet or more from adjacent lot lines and fire walls and 10 feet or more from fire barriers. Vents shall be uniformly located within the roof in the areas of the building where the vents are required to be installed by Section 910.2, with consideration given to roof pitch, sprinkler location- and structural members. Smoke and heat vent area. The required aggregate area of smoke and heat vents shall be calculated as follows: A = V/9000. Maintenance. Smoke and heat vents shall be maintained in an operative condition: Smoke and heat vents shall be maintained in accordance with NFPA 204. Fusible links for smoke and heat vents shall be replaced whenever fused, damaged or painted. The aggregate area of smoke and heat vents in buildings equipped throughout with an automatic sprinkler system to be calculated as follows: A.= V/9000 Retail Area: V = Volume of the North storage Area = 3,834 fix 18 ft2 = 69,012 ft3 A = Required Aggregate Vent Area = 69,012 ft3 / 9,000 = 8 ft2 8 f 2/32 ft2 = One vents [4'x8' each] required over the Retail Area Bulk Warehouse Area: V = Volume of the North storage Area = 8,159 ft 22 & = 179,498 & A = Required Aggregate Vent Area = 179,498 ft3 /9,000=20 & 20 ft2/32 62 = One vents [4'x8' each] required over the Bulk Warehouse Area M2 ingredients - 1900 Aston Ave., Carlsbad, CA Addendum to Report Dated March 20, 2019— Smoke and Heat Vents October 17, 2019 Page 2of2 It must be noted that the combined areas require only one smoke and heat vent. However we are conservatively installing two, due to the difference in ceiling heights for the two areas. If you have any questions or need additionally information do not hesitate to call us. Thank you for your consideration. Sincerely, Klausbruckner & Associates Inc. By way of my signature, M2 Ingredients agrees to meet the storage conditions re ds7er. Z?' M2 Ingredients Representative (Sign & Print Name & Title) Elley Klausbruckner, PE Fire Protection Consultant S-SV-CM CURB MOUNTED SINGLE DOME SHOWN S-Sv.SF SELF-FLASHING SINGLE DOME SHOWN $-SV2D-1.3-OA CURB MOUNTED SINGI SHOf S-SV2DV-SF SELF-FLASHING cimem ° nniAr HEIGHTS AND IT At is] W - AJ X " 160-1 7jg.' == c. Smoke Vent with SkyArc Dual-Lid IOPSF Smoke Vent Curb Mounted or Self-flashing or Louvered Base Curb Mounted or Self-flashing or Louvered Base _•f_ - -. 1. Acralight Solar's Non-Listed galvanized steel or aluminum smoke and heat vent features SkyArc capless dome design formed with Sky-Tough glazing for impact resistance. Units are equipped with a UL Listed and FM Approved fusible link and are available with an inside and/or outside manual release handle. Available as curb mounted, self-flashing, or louvered base models. Acralight Solar's galvanized steel or aluminum smoke and heat vent features a SkyArc capless dome design formed with SkyTough glazing for impact resistance. Units are equipped with a UL Listed and FM Approved fusible link, tested to ICC 15-7 and available with an inside and/or outside manual release. Available as a curb mount, self-flashing, louvered base or metal lid models. MODEL SV.CM (Non-louvered) or SV.L3-CM (Louvered) MODEL ROUGH OPENING FREE AREA (Louvered model) 4848 48° x 48° 6SF 3775 37° x 75° 7 SF 4669 46 '/" x 69 Y2° 7 SF 14689 46 1/2"x89W 8 S 4896 48" x 96" 9-SF - - 'Model 4896 available with 12 SF of Free Air - use SV-L4 designation. Model SV.CM (Curb mounted) or SF (Sell-flashing) Non-louvered Model SV-L3.CM (Curb mounted) or SF (Self-flashing) Louvered Model No. Example: 4896-S-SV.CM-ST.MF.OR 48" x 96" galvanized Blasi frame Imoke ient curb Mounted lcyIough glazing Mill Einish Qutside Manual Release Model No: Example: 4896-3-S V-L3-CM-ST-MF-OR 48" It 96" galvanized Iteel frame smoke Lent Louvered base Qurb Mounted kyIough glazing Mill Elnish Qulside Manual Release MODEL SV2D-CM (Non-louvered) or SV2D-L3-CM (Louvered) 4848-SV2D-L3 48° x 48° 6 SF 4848-S V2D 48" x 48° Model 4896 available With 12 SF of Free Air - use SV-L4 designation. Note: All models available in Curb Mounted or Self-flashing Note: Add lR to Model for an inside release or OR for an outside release Model SV2D-CM (Curb Mounted) or SF (Self-flashing) Non-Louvered Model SV2D-L3-CM (Curb Mounted) or SF (Self-flashing) Louvered Model No. Example: 4896-3-SV2D-CM-ST-MF-OR - - 48" x 96° galvanized Ileal frame Imoke Ment flual lid curb Mounted kyIough glazing Mill Elnish QuIside Manual Release Model No: Example: 4896-S-S V2D-L3-CM-ST.MF-OR 48" x 96" galvanized Iteel frame lmoke vent flual lid Louvered base Qurb Mounted kyIough glazing Mill Finish Qutside Manual Release 5 MZ (t4rpINT$ No.4326 T ey '- - —r I. 2—sc ~u(3 11LLI....I5 Ff . j 1oV t. 2, r' av,1 I A vvt O4T I A 41 L- 1,~ 16 -1 T ,ECI'LITE. PL/N4 Vie-ij, I LY\. FL) VLLJ I ..X ' (7 )1A.. •NO To Prepared for: Brian Lynch Industrial Commercial Systems 1165 Joshua Way Vist, CA 92081 Issued: 10.25.2019 MBO Inc. 4830 Viewridge Ave, Suite A San Diego, CA 92123 (858) 751-5702 www.mbol.com _____ CERTIFICATION# 1i ItJ 'IPfl RI"r .r,Lw 330 NEBB CERTIFIED TESTING, ADJUSTING & BALANCING REPORT PROJECT NAME: M2 Ingredients PROJECT ADDRESS: 1900 Aston Avenue, Suite 100 Carlsbad, CA 92008 ENGINEER: Plum Engineering, Inc. 11835 Carmel Mountain Road #1304 San Diego, CA 92128-4609 HVAC CONTRACTOR: Industrial Commercial; Systems 1165 Joshua Way, Vista,CA 92081 NEBB CONTRACTOR: MBO, Inc. 4619 Viewridge Ave. Suite C San Diego, CA 92123 MBO JOB NUMBER: Not Available NATIONAL ENVIRONMENTAL BALANCING BUREAU rT1 1 Ni Rp CERTIFICATION # IRS m In! 3306 NEBB CERTIFICATION PAGE PROJECT: M2 Ingredients ADDRESS: 1900 Aston Avenue Suite 100 Carlsbad, CA 92008 MBO JOB NO.: N/A THE DATA PRESENTED IN THIS REPORT IS AN EXACT RECORD OF SYSTEM PERFORMANCE AND WAS OBTAINED IN ACCORDANCE WITH NEBB STANDARD PROCEDURES. ANY VARIANCES FROM DESIGN QUANTITIES WHICH EXCEED NEBB TOLERANCES ARE NOTED THROUGHOUT THIS REPORT. THE AIR DISTRIBUTION SYSTEMS HAVE BEEN TESTED & BALANCED AND FINAL ADJUSTMENTS HAVE BEEN MADE IN ACCORDANCE WITH NEBB "PROCEDURAL STANDARDS FOR TESTING, ADJUSTING, BALANCING OF ENVIRONMENTAL SYSTEMS" AND THE PROJECT SPECIFICATIONS. NEBB TAB FIRM: MBO, Inc. REG. NO.: 3306 CERTIFIED BY: Dawayne Trobaugh DATE: 10-25-2019 THE HYDRONIC DISTRIBUTION SYSTEMS HAVE BEEN TESTED & BALANCED AND FINAL ADJUSTMENTS HAVE BEEN MADE IN ACCORDANCE WITH NEBB "PROCEDURAL STANDARDS FOR TESTING, ADJUSTING, BALANCING OF ENVIRONMENTAL SYSTEMS" AND THE PROJECT SPECIFICATIONS. NEBB TAB FIRM: MBO, Inc. REG. NO.: 3306 CERTIFIED BY: Dawayne Trobaugh DATE: N/A SUBMITTED AND CERTIFIED BY: NEBB TAB FIRM: MBO, Inc. REG. NO.: 3306 TAB SUPERVISOR: Dawayne Trobaugh SIGNATURE / Digitally signed by Dawayne Dawayne Troba ugh Trobaugh 2020.05.06 12:23:42 -07'00' NATIONAL ENVIRONMENTAL BALANCING BUREAU LL.1- Dog kL•ii NIi11!1II1I r dflOONO3J8 HP-18 DATA TEST SHEET TEST DATE: 20-Oct-2019 SUPERVISOR: Dawayne Trobaugh SYSTEM: HP--18 TAB TECH: Zac Long LOCATION: MANUFACTURER RHEEM MODEL RPOC-101DLA SERIAL ??45 G209800452 TOTAL CFM SUPPLY 4000 3725 TOTAL CFM RETURN 3600 3337 TOTAL CFM OSA 400 388 @@M : 8 1IJ&NL @ND @@goii 8 JILL I INLET S.P. NA I -0.307 NA I -0.844 DISCHARGE S.P. NA I 0.179 NA I 0.179 TOTAL S.P. NA / 0.486 NA / 1.023 Wpm MM MANUFACTURER Not Available CENTURY HP Not Available 3 PHASE Not Available 3 VOLTAGE Not Available ## AMPERAGE FLA 4 / / FRAME Not Available 56HZ RPM 1750 1752 SERVICE FACTOR Not Available 1.15 OVERLOAD TYPE/SIZE Not Available FLSR 35 Rm 1A9T I DRIVE MANUFACTURER BROWNING MOTOR SHEAVE 1VP150 x 7/8" FAN SHEAVE PK90 xl" RPM 898 BELTS (QTY/SIZE) 1 x B50 CENTER LINE 161/4" I MF1E11S N Or CERTIFIED MEMBER - NATIONAL ENVIRONMENTAL BALANCING BUREAU AIR DISTRIBUTION TEST SHEET TEST DATE: 20-Oct-2019 TAB SUPERVISOR: Dawayne Trobaugh SYSTEM: HP--18 TAB TECH: Zac Long LOCATION: RM WT.V. IRFFI[,NN FMIWEINAR mi. 00 HP-18.S1 SA NA 250 274 247 99% HP-18.S2 SA NA 750 609 702 94% HP-18.S3 SA NA 750 594 687 92% HP-18.54 SA NA 500 359 471 94% HP-18.S5 SA NA 750 620 691 92% HP-18.S6 SA NA 750 580 688 92% HP-18.S7 SA NA 100 121 98 98% HP-18.S8 SA NA 150 118 141 94% TOTAL 4000 3275 3725 93% — HP-18.141 RA NA 600 501 581 97% HP-18.R2 RA NA 600 486 561 94% HP-18.R3 RA NA 600 385 540 90% HP-18.R4 RA NA 600 447 540 90% HP-18.R5 RA NA 600 582 573 96% HP-18.R6 RA NA 600 202 542 90% TOTAL 3600 2603 3337 93% OSA OSA 400 672 388 97% I - MM'EiiftS N4 CERTIFIED MEMBER - NATIONAL ENVIRONMENTAL BALANCING BUREAU HP-22 DATA TEST SHEET TEST DATE: 20-Oct-2019 SUPERVISOR: Dawayne Trobaugh SYSTEM: HP--22 TAB TECH: Zac Long LOCATION: MANUFACTURER CARRIER MODEL 50TCQD08A2A5AOAOAO SERIAL 4510G60116 TOTAL CFM SUPPLY 3000 3160 TOTAL CFM RETURN 2700 2833 TOTAL CFM OSA 300 327 INLET S.P. NA / -0.441 NA / -0.911 DISCHARGE S.P. NA I 0.389 NA I 0.389 TOTAL S.P. NA I 0.830 NA I 1.300 MANUFACTURER Not Available MARATHON HP Not Available NOT STATED ON MOTOR TAG PHASE Not Available 3 VOLTAGE Not Available 208 AMPERAGE FLA 7.5 5.7 I I FRAME Not Available 56Y RPM 1750 . 1726 SERVICE FACTOR Not Available 1.15 YT1A DRIVE MANUFACTURER FENNER DRIVES MOTOR SHEAVE VP40 x 7/8" FAN SHEAVE AFD74 Xl" RPM 772 BELTS(QTY/SIZE) 11x A48 CENTERLINE 11711 I MME N. I11$ w- OP CERTIFIED MEMBER - NATIONAL ENVIRONMENTAL BALANCING BUREAU AIR DISTRIBUTION TEST SHEET L fl TlTrLrr TEST DATE: 20-Oct-2019 TAB SUPERVISOR: Dawayne Trobaugh SYSTEM: HP--22 TAB TECH: Zac Long LOCATION: _T TLN MI TLo EM T 1 ffiyp~ Q177NE Q EiGFiFNALM L r4 111111111111111111111111[WIMBER I HP-22-S1 SA NA 750 620 800 107% HP-22-S2 SA NA 750 688 813 108% HP-22-53 SA NA 750 626 784 105% HP-22-54 SA NA 750 614 763 102% TOTAL 3000 2548 0 3160 1050/6 HP-22-R1 RA NA 675 628 711 105% HP-22-R2 RA NA 675 550 737 109% HP-22-R3 RA NA 675 569 698 103% HP-22-R4 RA NA 675 552 687 102% TOTAL 2700 2299 0 2833 1051/6 OSA I I OSA I NA I I 300 I 249 I I 327 I 109% 4.2 V signal on A02 for the pneumatic CAV. CERTIFIED MEMBER - NATIONAL ENVIRONMENTAL BALANCING BUREAU i!!uIrrn AC = Air Conditioning Unit AH = Air Handler AHU = Air Handling Unit AMS = Air Monitoring Station ATM = Atmosphere AVG = Average BHP = Brake Horsepower BMS = Building Management System CD = Ceiling Diffuser CFM = Cubic Feet per Minute DIFF = Differential EA = Exhaust Air EF = Exhaust Fan EG = Exhaust Grill FPM = Feet per Minute GPM = Gallonsper Minute HP = Horsepower Hz = Hertz MAU = Make-up Air Misc. = Miscelaneous NA = Not Accesible NEBB = National Environmental Balancing Bureau NS = Not Specified NT = Not Tested OSA = Outside Air QTY = Quantity RH = Reheat RPM = Revolutions per Minute SA = Supply Air SWD = Side Wall Diffuser TAB = Testing, Adjusting, and Balancing VAV = Variable Air Volume VFD = Variable Frequency Drive ABBREVIATIONS PAGE ki CERTIFIED MEMBER - NATIONAL ENVIRONMENTAL BALANCING BUREAU ffirm (Cerfifftatton MBO, INC. HAS MET ALL REQUIREMENTS FOR NEBB CERTIFIED STATUS IN THE FOLLOWING DISCIPLINE Testing, Adjusting and Balancing of Environmental Systems 3306 J1q,A1 Jcl*~ NEBB Certification Number NEBB President March 31, 2022 Expiration Date NEBB President-Elect Certt"ftrtatt"on LWAYNE C. TROBAUGH HAS MET ALL REQUIREMENTS FOR NEBB CERTIFIED PROFESSIONAL STATUS IN THE FOLLOWING DISCIPLINE Testing, Adjusting and Balancing of Environmental Systems This Certificate, as well as individual affiliation with a NEBB Certified Firm and associated NEBB Certification Stamp are REQUIRED to provide a NEBB Certified Report. Participation in the NEBB Quality Assurance Program requires the Certificant be affiliated with a NEBB Certified Firm CP-23715 NEBB Certification Number March 31, 2022 Expiration Date NEBB President NEBB President-Elect JL; NEBB Certification Board NEBB Certified Technician Peter MichaeCGarcta10 AS MET ALL THE NEBB REQUIREMENTS FOR NEBB CERTIFIED TECHNICIAN STATUS IN resting fldjustIng and 2?afàncIng of2nvIronmenta1Systems This Certificate, as well as individual affiliation with a NEBB Certified Firm and associated NEBB Certification Stamp are REQUIRED to provide a NEBB Certified Report. Participation in the NEBB Quality Assurance Program requires the Certificant be affiliated with a NEBB Certified Firm. 9vlarcli 31, 2021 Expiration Date NEBB Certification Board Chairman 21848 NEBB Certificaut Number NEBB Certification Director The NEBB Certification Board retains sole ownership of all certificates. The NEBB Certification Board Policy Manual governs use of this certificate. AIRDATA MULTIMETER CERTIFICATE OF RECALIBRATION Customer ID:018503 SIN: M07598 bustomer: MBO. INC. City: SAN DIEGO State: CA As-Received Model #:ADM-860C Converted to Model #: Order#:R193066 P0 #: Customer Eqpt ID#:_ Calibration Due Date:______________ This instrument has been calibrated using Calibration Standards which are trac is 4:1 for pressures and temperature. Quality Assurance Program and calibrati 45662A and manufacturers specifications. Calibration accuracy is certified wh expressed in expanded terms (twice the calculated uncertainty). This report Instruments, Inc. Results relate only to the item calibrated. For limitations c Multimeters. Procedure used: Procedure for Differential Pressure, Absoli Revision: 30 Dated: 04/04/16 Calibration Technician(s): YV\. ( Calibration Approved by: .i(Y'i '.1 Q .. AS-Received By IY\. D. tLTest Date lo- 12p(( Rh 2_, % Date_____ Ambient Temperature Ambient Tempi Barometric Pres re 2..R. 3 ( in Hg Barometric Pre All within spec YES NO NA All within spec to NIST (National Institute of )n Manual lOt me use AirData Multimeters - Calibration Date:/ C /L i/? ,, 9 .._C -e_e. Date:it Test By______________ Da Rh % _°F Ambient Tern e .OF Hg Barometric Pressure . in Hg All within spec YES NO iall not be use, see Pressure NO ABSOLUTE PRESSURE TEST (in Hg) TEST METER TOLERANCE = * 2.0 % *.1 in Hg AS-RECEIVED TEST WITHIN SPEC YES NO N/A See Notes Pressure Standard: Heise #02-R SIN: 41741/42451 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #12A- IN: 45605/48491 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #04-R SIN: 41743/42453 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #14-R SIN: 43412/45043-2 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #06-R SIN: 41742/42452-1 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #16-R SIN: 43413/45044 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #08-R SIN: 42186/43328 s-Rcv0 Test 2 Test 3 Pressure Standard: Heise #18-R SIN: 44561/46645 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #10-R SIN: 42203/43352 As- cvdc1ëi Test 3 Pressure Standard: Heise #20-R SIN: 44582/46847 As-Rcvd Test 2 Test 3 Approx Set Pt Standard Test Meter % Diff Standard Test Meter % Duff Standard Test Meter % Duff _ DIFFERENTIAL PRESSURE TEST (in wc) TEST METER TOLERANCE = ± 2.0 % * 0.001 in wc AS-RECEIVED TEST WITHIN SPEC YES NO N/A See Notes Pressure Standard: Heise #01-L SIN: 41739/42449 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #11-L S/N: 43165/44551-1 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #01-R SIN: 41739/42446 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #11-13 SIN: 43165/44730 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #02-1 SIN: 41741/42454 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #12A-L SIN: 45605/48490 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #03A-L SIN: 45570/48461 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #13-1 SIN: 43415/45041 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #03A-R SIN: 45570/48460 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #13-R SIN: 43415/45039 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #04-1 SIN: 41743/42456 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #14-L SIN: 43412/45045 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #05-1 SIN: 41740/42450 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #15-L SIN: 43416/45042 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #05-R SIN: 41740/42447 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #15-R SIN: 43416/45040 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #06-L SIN: 41742(42455 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #16-L SIN: 43413/45046 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #07-L SIN: 42185/42186 s-Rc Test 2 Test 3 Pressure Standard: Heise #17-L SIN: 44579/46842 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #07-R SIN: 42185/43328 s- cv Test 2 Test 3 Pressure Standard: Heise #17-R SIN: 44579/46841 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #08-L SIN: 42186/43329 Est Rcv Test 2 Test 3 Pressure Standard: Heise #18-1 SIN: 44581/46846 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #09-1 SIN: 42202/43351 As-Rcvd es Test 3 Pressure Standard: Heise #19-1 SIN: 44580/46844 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #09-R SIN: 42202/43350 As-Rcvd 3AfttpTest 3 Pressure Standard: Heise #19-R SIN: 44580/46843 As-Rcvd Test 2 Test 3 Pressure Standard: Heise #10-L SIN: 42203/43353 As-Rcvd est Test 3 Pressure Standard: Heise #20-1 SIN: 44582/46848 As-Rcvd Test 2 Test 3 Aoorox Set Pt Standard Test Meter % Duff Standard Test Meter % Duff Standard Test Meter % Duff .0500 052..0 .0S1 -.9 .O9- .6501 —.a .1250 .i257 .2.S5 -.(6 15Lf )5 IL .2250 - .7- L56 23.S 2> 11;510 1.000 1024 1.016 .LO Loia I. 0/5 130 2.000 e) .0j3.25 '00L1 a,QQ5 3.600 3.(9 3.6( ( 3.Cpi(.' 3,e,005 4.400 4.10C '-(.'-(2( -'( Li . -(O t-f.'-(I5- .1 27.00 2--7.o( 2:7.05 -15 17. 0! a-). o S 07 50.00 iiCA.11 coo( .o'-f O.O3 L(C1t3I, , (L( Overange NA NA NA NA NA I NA N Shortridge Instruments, Inc. 7855 East Redfield-Road Scottsdale, Arizona 85260 (480) 991-6744 • Fax (480) 443-1267 • www.shortridge.com ADM Recatibration Rev48/10/14/19 1 of 2 10/14/19 AIRDATA MULTIMETER CERTIFICATE OF RECALIBRATION S/N:r(\O75? Order#: ?-t 3O6 LOW VELOCITY CONFIRMATION (FPM) TEST METER TOLERANCE = ± 3.0% ± 7 FPM AS-RECEIVED TEST WITHIN SPEC I1JO N/A See Notes Val Eqv Trans Std: S/N: M02009 Test 2 Test 3 Val Eqv Trans Std: SIN: M10897 As-Rcvd Test 2 Test 3 Val Eqv Trans Std: S/N: M02903 As-Rcvd Test 2 Test 3 Val Eqv Trans Std: SIN: M10901 As-Rcvd Test 3 Vet Eqv Trans Std: SIN: M10839 As-Rcvd Test 2 Test 3 Vet Eqv Trans Std: SIN: M13492 As-Rcvd Test 2 Test 3 Vet Eqv Trans Std: SIN: M10840 As-Rcvd Test 2 Test 3 Val Eqv Trans Std: SIN: M19325 As-Rcvd Test 2 Test 3 Annr.w 5t D.siI Thot Rflr fliff Sfn,2rd Too* Mtr nff Standard TPqt Meter fliff I100 II osg I k os- 1 -811 iou— I ioi I --i I500 II 315.2.1 -9 (3 -1.2.11 S, I I !O ADM-880C, ADM-870/870C and ADM-860/860C models are read in AirFoil Mode. ADM-850/850L models are read in Pilot Tube Mode. TEMPERATURE TEST - AIRDATA MULTIMETER (° F TEST METER TOLERANCE =* 0.2° F AS-RECEIVED TEST WITHIN SPEC YES NO N/A See Notes RTD Simulator: SIN 249 As-Rcvd (Te Test 3 Set Point 1 , 95° F 154.4° F RTD Simulator: SIN 250 As-Rcvd e Test 3 Set Point: 35.6° Fc:i 5 154.4° F RTD Simulator: SIN 253 As-Rcvd Test 2 Test 3 Set Point: 35.6° F 95° F RTD Simulator: SIN 254 As-Rcvd Test 2 Test 3 Set Point: 35.6° F 95° F 154.4° F RTD Simulator: SIN 256 As-Rcvd Test 2 Test 3 Set Point: 35.6° F 95° F 154.4°F RTD Simulator: SIN 257 As-Rcvd Test 2 Test 3 Set Point: 35.6° F 950 F 154.4°F RTD Simulator: SIN 292 As-Rcvd Test 2 Test 3 Set Point: 35.6° F 95° F 154.4°F RTD Simulator: SIN 293 As-Rcvd Test 2 Test 3 Set Point: 35.6° F 95° F 154.4°F RID Simulator: SIN 294 As-Rcvd Test 2 Test 3 Set Point: 35.6° F 95° F 154.4° F RID Simulator: SIN 313 s-Rcv Test 2 Test 3 Set Point. QED 95° F 154.4°F RTD Simulator: SIN 314 s-Rcvd Test 2 Test 3 Set Point: 35.6° Fc 154.4°F RID Simulator: SIN 315 s-Rcvd Test 2 Test 3 Set Point: 35.6° F 95° F IEED RTD Simulator: SIN 316 As-Rcvd Test 2 Test 3 Set Point: 35.6° F 950 F 154.4° F RTD Simulator: SIN 317 As-Rcvd Test 2 Test 3 Set Point: 35.6° F 950 F 154.40F RTD Simulator: SIN 318 As-Rcvd Test 2 Test 3 Set Point: 35.6° F 950 F 154.40F RTD Simulator Temperature Fntiivelent qpt Pnint Test Meter flifferenp Test Meter flifFerenp Test Meter flifferene I 35.60 II '45.6 I 0 I 2 '. ' ° I 95.00 c .c. 0 I o II C? O II I 154.40 II 159 5 I II SCsI .5' I I II NOTES: The enclosed ADM Calibration Standards for Pressure and Temperature form(s) :islare an integral part of this calibration and must remain with this Certificate of Calibration. Note: There may be more than one such form included that pertains to this calibration. Shortridgç Instruments, Inc. 7855 East RedfieId'Road Scottsdale, Arizona 85260 (480) 991-6744 • Fax (480) 443-1267 • www.shortridge.com ADM RecaIibraton Rev48I1 0114119 2 of 2 10/14119 Co ID:O 1, 6 S C) MUL III EMI PtNU/IJK I tMFKUbt V%tL;ALIbKA IIUI'I I tZl I rrurc i uraer:r-. I u Customer: _C'\O, 1i1I C. - City: So-c T5 State:_ CA _________ Procedure used: Procedure for Calibration/Recalibration of MultiTemps and/or TemProbes SIP-CPI4 Rev: 03 Dated: 07/31/14 Equipment Being Tested: MultiTemp and TemProbes TemProbe(s) LI-111 TEMPERATURE TEST (° F MULTITEMP TOLERANCE (MULTITEMP AND TEMPROBES TESTED AS A UNIT) = ± 0.5° F TEMPROBE TOLERANCE = ± 0.3° F Thermometer 91 SIN 8A089 I Thermistor SIN A410660 Set Point: 35° F 950 F 1550 F Thermometer #2 SIN 8B104 / Thermistor SIN 871507 Set Point: 35° F 155°F Thermometer #5 SIN B1 1780 1 Thermistor SIN 610505 Set Point: 35° F 95° F Thermometer #6 SIN 1311782 I Thermistor SIN B10509 Set Point:6 950 F 155° F Thermometer #7 SIN 649938! Thermistor SIN B482202 Set Point: 35° F 950 F 155° F Temperature Standard AirData Multimeter SIN M001 36 Set Point: 350 F 95'F 155'F Temperature Standard AirData Multimeter SIN M96100 Set Point:! Test By: rY\. h.jrnD Date:lo- (R-16(9 Rh:_. % Ambient Temperature: ..°F Barometric Pressure:2.3'1_in Hg Test Test Test Test Test Test Test Test Probe #1 Probe #2 Probe #3 Probe #4 K Probe #5 Probe #6 Probe #7 Probe #8 Approx Temp ADT- t ADT- ADT- AOT- AOl- AOl- AOT- AOl- St Point Standard iwiiil• U U U • -----------.---- -___. A check in the box to the right of a Tern Probe reading indicates that the reading is Out Of Specification. If all As-Received readings were within specification, and no repairs were performed, no Final test is required. NOTES: FINAL TEMPERATURE TEST (° F) MULTITEMP TOLERANCE (MULTITEMP AND TEMPROBES TESTED AS A UNIT) = ± 0.5° F TEMPROBE TOLERANCE = ± 0.3° F Thermometer #1 SIN 8A089 / Thermistor SIN A410660 Set Point: 35° F 950 F 1550 F Thermometer #2 SIN 813104 I Thermistor SIN 871507 Set Point: 350 F 95° F 1550 F Thermometer #5 SIN 611780/Thermistor SIN 610505 Set Point: 350 F 950 F 1550 F Thermometer #6 SIN B11782 / Thermistor SIN B10509 Set Point: 350 F 95° F 155° F Thermometer #7 SIN 649938 I Thermistor SIN B482202 Set Point: 350 F 95'F 1550 F Temperature Standard AirData Multimeter SIN M001 36 Set Point: 35° F 950 F 1550 F Temperature Standard AirData Multimeter SIN M96100 Set Point: 35° F 95° F 1550 F Test By: Date: Rh: % Ambieftt4enpeFaturc: OF BarometFie-Pcessuro: in-Mg- Test Test Test Test Test Test Test Test Probe #1 Probe #2 Probe #3 0 robe #4 Probe #5 Probe #6 Probe #7 Probe #8 o,rox, ______ AOl-______ ADT-______ ADT-______ ADT-______ ADT- AOT______ AOT______ —ADT_____ NOTES: Calibration standards used by Shortridge Instruments, Inc. are traceable to NIST (National Institute of Standards and Technology). Calibration is performed in accordance with ANSIINCSL Z540-1, ISO 17025, MIL-STD 45662A and manufacturers specifications. Calibration accuracy is certified when meters are used with properly functioning accessories only. This report shall not be reproduced, except in full, without the written approval of Shortridge Instruments, Inc. Results relate only to the item calibrated. Limitations on use: See Shortridge Instruments, Inc. Instruction Manual for the use of AirData Multimeters. The enclosed ADM or HDM Calibration Standards form(s) is/are an integral part of this calibration and must remain with this Certificate of Calibration. Note: There may be more than one such form included that pertains to this calibration. Calibration Approved by: (s" (Zv fe-z Title:Lo_Sit t_4__tS, Date: N' bi -zokl Shortridge Instruments, Inc. ° 7855 E Redfiel Road, Scottsdale, AZ 85260 • (480) 991-6744 • Fax (480) 443-1267 . www.shortridge.com MultiTempReCal Rev11112/11114 1 of 1 12111114 Shortridge Instruments, Inc. AirData Multimeter Calibration Equipment Order Number: K01066 Serial Number: (n&7S9 & Test Type: Initial ABSOLUTE PRESSURE STANDARDS ADM #02-R SIN: 41741/42451 Heise Model: PPM-2 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 04/30/19 Due Date: 04/2020 ADM #04-fl SIN: 41743/42453 Heise Model: PPM-2 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 11128/18 Due Date: 1112019 ADM #06-R SIN: 41742/42452-1 Heise Model: PPM-2 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 08/21/19 Due Date: 08/2020 ADM #08-R SIN: 42186143328 Heise Model: PPM-2 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 03/22/19 Due Date: 03/2020 ADM #10-R SIN: 42203/43352 Heise Model: PPM-2 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 01/21/19 Due Date: 01/2020 ADM #12A-R SIN: 45605/48491 Heise Model: PPM-2 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 07/16/19 Due Date: 07/2020 ADM #14-fl SIN: 43412/45043-2 Heise Model: PPM-2 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 10/07/19 Due Date: 09/2020 ADM #16-R SIN: 43413/45044 Heise Model: PPM-2 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 02/20/19 Due Date: 02/2020 ADM #18-fl SIN: 44581/46845 Heise Model: PPM-2 Mfgd & Calibrated by Ashcroft, Inc. Calibration Date: 05/17/19 Due Date: 05/2020 ADM #20-R SIN: 44582/46847 Heise Model: PPM-2 Mfgd & Calibrated by Ashcroft, Inc. Calibration Date: 06/20/19 Due Date: 06/2020 #02-R, 04-R, 06-R, 08-R. 10-R, 12A-R, 14-fl, 16-R Rated Accuracy: 0.05% Is (0.0305 in Hg) Range: 0-30 psia Resolution: 0.01 Uncertainty: <0.0358 #18-fl, 20-R Rated Accuracy: 0.05% Is (0.0305 in Hg) Range: 0.60 in Hg Resolution: 0.001 Uncertainty: <0.0358 DIFFERENTIAL PRESSURE STANDARDS ADM #01-1 SIN: 41739/42449 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 05/01119 Due Date: 04/2020 ADM #01-R SIN: 41739/42446 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 05101119 Due Date: 04/2020 ADM #02-1 SIR 41741142454 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 05/01/19 Due Date: 04/2020 ADM #03A-L SIN: 45570/48461 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 11/28/18 Due Date: 11/2019 ADM #03A-R SIN: 45570/48480 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 11/28/18 Due Date: 11/2019 ADM #04-1- SIN: 41743/42456 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 11/28/18 Due Date: 11/2019 ADM #05-1 SIN: 41740/42450 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 08/26/19 Due Date: 08/2020 ADM #05-R SIN: 41740/42447 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 08/28/19 Due Date: 08/2020 ADM #06-1 SIN: 41742/42455 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 08/26/19 Due Date: 08/2020 ADM #07-1- SIN: 42165/42186 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 03/26/19 Due Date: 03/2020 ADM #07-R SIN: 42185/43326 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 03/26/19 Due Date: 03/2020 ADM #08-1 SIN: 42188/43329 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 03125119 Due Date: 03/2020 ADM #09-1 SIN: 42202/43351 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 01/23/19 Due Date: 0112020 ADM #09-R SIN: 42202/43350 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 01/23/19 Due Date: 01/2020 ADM #10-1 SIN: 42203/43353 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 01/23/19 Due Date: 01/2020 ADM #11-1 SIN: 43165/44551-I Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 07/15/19 Due Date: 07/2020 ADM #11 -R SIN: 43165/44730 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 07/15/19 Due Date: 07/2020 ADM #12A-L SIN: 45605/48490 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 07116/19 Due Date: 07/2020 ADM #13-1 SIN: 43415/45041 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 09/19/19 Due Date: 09/2020 ADM #13-R SIN: 43415/45039 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 09/19/19 Due Date: 09/2020 ADM #14-1. SIN: 43412/45045 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 09/19/19 Due Date: 09/2020 ADM #15-1 SIN: 43416/45042 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 02/22/19 Due Date: 02/2020 ADM #15-R SIN: 43416/45040 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 02/22/19 Due Date: 02/2020 ADM #16-1- SIN: 43413/45046 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 02/21/19 Due Date: 02/2020 ADM #17-L SIN: 44579/46842 Heise Model: PPM-1 Mfgd & Calibrated by Ashcroft, Inc. Calibration Date: 05116119 Due Date: 05/2020 ADM #17-R SIN: 44579/46841 Heise Model: PPM-i Mfgd & Calibrated by Ashcroft, Inc. Calibration Date: 05/21/19 Due Date: 05/2020 ADM #18-1- SIN: 44581/46848 Heise Model: PPM-1 Mfgd & Calibrated by Ashcroft, Inc. Calibration Date: 05/16/19 Due Date: 05/2020 AOM419-1. SIN: 44580/46844 Heise Model: PPM-1 Mfgd & Calibrated by Ashcroft, Inc. Calibration Date: 07/15/19 Due Date: 06/2020 ADM #19-R SIN: 445130/46843 Heise Model: PPM-1 Mfgd & Calibrated by Ashcroft, Inc. Calibration Date: 07/15/19 Due Date: 06/2020 ADM #20-1 SIN: 44582/46848 Heise Model: PPM-1 Mfgd & Calibrated by Ashcroft, Inc. Calibration Date: 08/i 8119 Due Date: 06/2020 #oi-L, 03A-L, 05-1, 07-1, 09-L, 11-L, 13-L, 15-L 17-L. 19-L Rated Accuracy: >0.07% Is (0.000175 in wc) Range: 0.0-0.25 in wc Res.: 0.00001 Uncertainty: <0.00035 #oi-R, 03A-R, 05-R. 07-R,09-R, 1 i-R, 13-R, 15-R, 17-R, I9-R Rated Accuracy: >0.06% Is (0.003 in wc) Range: 0.0-5.0 In we Res.: 0.0001 Uncertainty: <0.00348 #02-1, 04-1, 06-L, 08-1, 10-1, 12A-L. 14-L, I6-L, 18-L, 20-1 Rated Accuracy: >0.06% Is (0.03 in wc) Range: 0.0-50.0 in wc Res.: 0.001 Uncertainty: <0.0346 Shortridge Instruments, Inc. 7855 East Redfield Road Scottsdale, Arizona 85260 (480) 991-6744 • Fax (480) 443-1267 • www.shortridge.com ADM Cal Stnds Rev 15/10/14/19 1 of 2 10/14/19 Shortridge Instruments, Inc. AirData Multimeter Calibration Equipment Customer Order Number, Meter Serial Number, and Test Type are referenced on page 1 LOW VELOCITY EQUIVALENT CONFIRMATION STANDARDS Vet Eqv Transfer Standard SIN: M02009 Model ADM-870C Mfgd & Calibrated by Shortridge Instruments, Inc. Calibration Date: 12/07/18 Due Date: 12/2019 Vet Eqv Transfer Standard SIN: M02903 Model ADM-870C Mfgd & Calibrated by Shortridge Instruments, Inc. Calibration Date: 12/07/18 Due Date: 12/2019 Vet Eqv Transfer Standard SIN: M10839 Model ADM-870C Mfgd & Calibrated by Shortridge Instruments, Inc. Calibration Date: 12/07/18 Due Date: 12/2019 Vet Eqv Transfer Standard SIN: M10840 Model ADM-870C Mfgd & Calibrated by Shortridge Instruments, Inc. Calibration Date: 12/07/18 Due Date: 12/2019 Vet Eqv Transfer Standard SIN: M10897 Model ADM-870C Mfgd & Calibrated by Shortridge Instruments, Inc. Calibration Date: 01/171`19 Due Date: 01/2020 Vet Eqv Transfer Standard SIN: Ml 0901 Model ADM-870C Mfgd & Calibrated by Shortridge Instruments, Inc. Calibration Date: 12/07/18 Due Date: 12/2019 Vet Eqv Transfer Standard SIN: M13492 Model ADM-870C Mfgd & Calibrated by Shortridge Instruments, inc. Calibration Date: 08/08/19 Due Date: 08/2020 Vet Eqv Transfer Standard SIN: M19325 Model ADM-870C Mfgd & Calibrated by Shortridge Instruments, Inc. Calibration Date: 06/21/19 Due Date: 0612020 Rated Accuracy: Velocity ± 1.5%:t 3.5 fpm Range: 100-5000 fpm Resolution: 0.1 Uncertainty: <5.00 fpm at 100 fpm; <7.50 fpm at 500 fpm TEMPERATURE STANDARDS RTD Simulator SIN: 249 Model RTD-1000/500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 03/16/16 Due Date: 03/2020 RTD Simulator SIN: 250 Model RTD-1000/500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 03/16/16 Due Date: 03/2020 RTD Simulator S/N: 253 Model RTD-1000/500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 03/16/16 Due Date: 03/2020 RID Simulator SIN: 254 Model RTD-1000/500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 04/07/18 Due Date: 04/2020 RTD Simulator SIN: 256 Model RTD-1000/500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 04/07/16 Due Date: 04/2020 RID Simulator SIN: 257 Model RID-bOO/SOD Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 04/07/18 Due Date: 0412020 RTD Simulator SIN: 292 Model RTD-1000/500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 12/21/15 Due Date: 12/2019 RTD Simulator SIN: 293 Model RTD-1000/500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 12/21/15 Due Date: 12/2019 RTD Simulator SIN: 294 Model RTD-1000/500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 12/21/15 Due Date: 12/2019 RTD Simulator SIN: 313 Model RTD-1000/500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 03/16/18 Due Date: 03/2022 RTD Simulator SIN: 314 Model RTD-1000/500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 03/16/18 Due Date: 03/2022 RTD Simulator SIN: 315 Model RTD-1000/500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 03/16/18 Due Date: 03/2022 RTD Simulator SIN: 316 Model RTD-10001500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 04/16/18 Due Date: 04/2022 RID Simulator SIN: 317 Model RTD-1000/500 Mfgd by General Resistance . Calibrated by lET Labs Calibration Date: 04/16/18 Due Date: 04/2022 RID Simulator SIN: 318 Model RTD-1000/500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 04/16/18 Due Date: 04/2022 Rated Accuracy: 0.025% of setting Range: 100.00 Q to 11111.100 Resolution: 0.01 0 Uncertainty: s 32 ppm Thermometer #1 SIN 8A089lThermistor SIN A410660 Model 1504/5610 Mfgd by Hart Scientific Calibrated by Fluke Calibration Date: 08/27/19 Due Date: 08/2021 Thermometer #2 SIN 89104/Thermistor SIN 871507 Model 1504/5810 Mfgd by Hart Scientific Calibrated by Fluke Calibration Date: 11/07/18 Due Date: 10/2020 Thermometer #5 SIN B11780lThermlstor SIN B10505 Model 1504/5610 Mfgd by Hart Scientific Calibrated by Fluke Calibration Date: 03/07/19 Due Date: 03/2021 Thermometer #6 SIN Bll782lThermistor SIN 810509 Model 1504/5610 Mfgd by Hart Scientific Calibrated by Fluke Calibration Date: 02/20/18 Due Date: 02/2020 Thermometer #7 SIN B49938/Thermlstor SIN B482202 Model 1504/5610 Mfgd and Calibrated by Fluke Calibration Date: 09/26/19 Due Date: 09/2021 Rated Accuracy(combined): 0.0324° F Range: 32° F to 176° F Resolution: 0.001° F Combined Uncertainty with Baths: so.040° F Temp Transfer Standard SIN M00136 Model ADM-870 Mfgd & Calibrated by Shortridge Instruments, Inc. Calibration Date: 10/02/19 Due Date: 10/2020 Temp Transfer Standard SIN M96100 Model ADM-870 Mfgd & Calibrated by Shortridge Instruments, Inc. Calibration Date: 03/07/19 Due Date: 03/2020 Rated Accuracy: 0.03° F Range: 33° F to 158° F Resolution: 0.01° F Uncertainty: <0.023° F Total combined Uncertainty for MultiTemp and TemProbe testing: s 0.046° F This form must remain with the Certificate of Calibration Corresponding to the Customer Order Number and Meter Serial Number referenced on page 1. Shortridge Instruments, Inc. 7855 East Redfield Road Scottsdale, Arizona 85260 (480) 991-6744 • Fax (480) 443-1267 • www.shortridge.com ADM Cal Stnds Rev 15/10/14/19 2 of 2 10/14119 AIRDATA FLOWMETER CERTIFICATE OF RECALIBRATION Customer ID:018503 SIN: M07598 Customer:MBOI INC. City:SAN DIEGO State: CA As-Received Model #: ADM-860C Converted to Model #: Order #:R193066 This instrument has been calibrated using Calibration Standards which are traceable to NIST (National Institute of Standards and Technology). Quality Assurance Program and calibration procedures meet the requirements for ANSI/NCSL Z540-1, ISOe 17025, MIL-STD 45662A and manufacturers specifications. Calibration accuracy is certified when meters are used with properly functioning accessories only. Test Accuracy Ratio is 2:1 for air flow calibration. All specified uncertainties are expressed in expanded terms (twice the calculated uncertainty). This report shall not be reproduced, except in full, without the written approval of Shortridge Instruments, Inc. Results relate only to the item calibrated. Limitations on use: See Shortridge Instruments, Inc. Instruction Manuals for the use of AirData Multimeters and FlowMeters. Procedure used for air flow: Procedure for Recalibration of AirData Multimeters on a FlowHood SIP-CP06 Revision: 14 Dated: 12/10115 AIR FLOW TEST (cfm) TEST METER TOLERANCE: ± 3.0% of reading ±7 cfm Calibration Equipment: iFlowHood Stand Calibration Transfer Standard AirData Multimeter Model ADM-870, Serial Number M99083 or M98543 and FlowHood Calibration Stand SIN 7401 calibrated as a system. Manufactured by Shortridge Instruments, Inc. System Calibration Date: 04/18-22/19. System Calibration Due Date: 04/2021. FlowHood Stand Calibration Transfer Standard AirData Multimeter Model ADM-870, Serial Number M99420 and M96452 and FlowHood Calibration Stand SIN 7401 calibrated as a system. Manufactured by Shortridge Instruments, Inc. System Calibration Date: 04/06-13/18. System Calibration Due Date: 04/2020. Rated accuracy of system is ± 1.5% of reading ± 3.5 cfm. Resolution is 0.1 cfm. The uncertainty of the system is as stated at each Set Point. All readings are compensated for the density effects of barometric pressure and temperature. AS-RECEIVED TEST CONDITIONS Transfer Standard: M96452 M98543 q9iDM99420 Relative Humidity: 2-S % Ambient Temperature: 7S__°F Barometric Pressure: 2-9.3-L in Hg Calibrated By: Vr. Calibration Date: Within Spec: Des No NA See Notes As-Recvd Test performed using: orner'i1ln-House Base FINAL TEST CONDITIONS Transfer Standard:2 M98543 M99083 M99420 Relative Humidity: 2.0_% Ambient Tmperature: •1'1 °F Barometric Pressure: t._(3 in Hg Calibrated By: '- Calibrated Date: IL OL 2.019 Final Test performed using: er's aas In-House Base Calibration Approved by: Title: Date: ___ø. _Z -9 I. Approximate Set Point Set Point Uncertainty AS-RECEIVED TEST FINAL TEST Standard Test Meter Difference Standard Test Meter Difference 100 <5.0% lol. i ct 102... 500 <1.5 % 6'-1 L.l9 ç? - 503 So f - 1000 <1.5% 100A (oo tool- 1 601 1500 <1.25% 55 (S-L3 tSoi (5T7 2000 <1.25% )c 2.o3 'Loot 2c33 3( Notes Shortridge Instruments, Inc. 7855 East Redfield Road Scottsdale, Arizona 85260 (480) 991-6744. Fax (480) 443-1267. www.shortridge.com FlowMeter Recalibration 850.883-870 Rev12I03/05119 1 of 1 05/01119 MULTITEMP AND/OR TEMPROBE CALIBRATION TEST REPORT CO ID: Order#:I'(q3Cta( Customer: (31 130 I &)C -. city: •C34 ,J 1) c State: (1, /1- Procedure used: Procedure for Calibration/Recalibration of MultiTemps and/or TemProbes SIP-CPI4 Rev: 03 Dated: 07/31/14 Equipment Being Tested: MultiTemp and TemProbes TemProbe(s) i..— TEMPERATURE TEST (° F) MULTITEMP TOLERANCE (MULTITEMP AND TEMPROBES TESTED AS A UNIT) = ± 0.5° F TEMPROBE TOLERANCE = ± 0.3° F Thermometer #1 SIN 8A089 / Thermistor S/N A410660 Set Point: 35° F 95° F 155° F Thermometer #2 SIN 8131104 I Thermistor SIN 871507 Set Point: 35° F 1550 F Thermometer #5 S/N 611780/Thermistor S/N B10505 Set Point: 35° F 95° F Thermometer #8 SIN 611782 I Thermistor S/N B10509 Set Point<) 95° F 155° F Thermometer #7 SIN 649938 I Thermistor S/N B482202 Set Point: 35° F 95° F 155° F Temperature Standard AirData Multimeter S/N M00136 Set Point: 35° F 95° F 155° F Temperature Standard AirData Multimeter SIN M96100 Set Point(i' c, Test By: c ). k05r>J9b Date: JI3o/..ai £ Rh:3 % Ambient Temperature: ...2°F BarometricPressure:;ZZ,69 in Hg Test Test Test Test Test Test Test Test Probe #1 Probe #2 Probe #3 Probe #4 Probe #5 Probe #6 Probe #7 Probe #8 Approx Temp ADT- 4t19. AOl- AOl AOl- tjf AST AOl AOl AOl— Set Point Standard 35°II 3.c:I 35.o 95011 q s.o Iq s. 1550i15O I i 55.o NOTES: Calibration standards used by Shortridge Instruments, Inc. are traceable to NIST (National Institute of Standards and Technology). Calibration is performed in accordance with ANSI/NCSL Z540-1, ISO 17025, MIL-STD 45662A and manufacturer's specifications. Calibration accuracy is certified when meters are used with properly functioning accessories only. This report shall not be reproduced, except in full, without the written approval of Shortridge Instruments, Inc. Results relate only to the item calibrated. Limitations on use: See Shortridge Instruments, Inc. Instruction Manual for the use of AirData MuItimeters The enclosed ADM or HDM Calibration Standards form(s) is/are an integral part of this calibration and must remain with this Certificate of Calibration. Calibration Approved by:(V\ . Title: Date: Shortridge Instruments, Inc. 7855 East Redfield Road Scottsdale, Arizona 85260 (480) 991-6744 • Fax (480) 443-1267 • www.shortridge.com MultiTemp Cal Rev1O!1V11/14 1 of 1 12111114 Shortridge Instruments, Inc. AirData Multimeter calibration Lqulpment Order Number: £ i Serial Number: robe Test Type: ial As-Received Final ABSOLUTE PRESSURE STANDARDS ADM #02-11 SIN: 41741/42451 Heise Model: PPM-2 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 04130/19 Due Date: 04/2020 ADM #04-R SIN: 41743/42453 Heise Model: PPM-2 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 11/28/18 Due Date: 1112019 ADM #06-R SIN: 41742/42452-1 Heise Model: PPM-2 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 08/21119 Due Date: 08/2020 ADM #08-R SIN: 42186/43328 Heise Model: PPM-2 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 03/22/19 Due Date: 03/2020 ADM #10-R SIN: 42203/43352 Heise Model: PPM-2 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 01/21/19 Due Date: 0112020 ADM #12A-R SIN: 45605/48491 Heise Model: PPM-2 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 07116/19 Due Date: 07/2020 ADM #1 4-R SIN: 43412/45043-2 Heise Model: PPM-2 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 10107/19 Due Date: 09/2020 ADM #16-R SIN: 43413/45044 Heise Model: PPM-2 Md by Dresser Industries Calibrated by Ashcroft Calibration Date: 02/20119 Due Date: 02/2020 ADM #18-R SIN: 44581/46845 Heise Model: PPM-2 Mfgd & Calibrated by Ashcroft, Inc. Calibration Date: 05/17/19 Due Date: 05/2020 ADM #20-R SIN: 44582/46847 Heise Model: PPM-2 Mfgd & Calibrated by Ashcroft, Inc. Calibration Date: 06/20/19 Due Date: 06/2020 #02-R, 04-R, 06-R, 08-R, 10-R. 12A-R. 14-R, 16-R Rated Accuracy: 0.05% Is (0.0305 in Hg) Range: 0-30 psia Resolution: 0.01 Uncertainty: <0.0358 #18-R, 20-R Rated Accuracy: 0.05% Is (0.0305 in Hg) Range: 0-60 in Hg Resolution: 0.001 Uncedalnty. <0.0358 DIFFERENTIAL PRESSURE STANDARDS ADM #01-L SIN: 41739/42449 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 05/01/19 Due Date: 04/2020 ADM #01-R SIN: 41739/42446 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 05/01119 Due Date: 04/2020 ADM #02-1. SIN: 41741/42454 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 05/01/19 Due Date: 04/2020 ADM #03A-L SIN: 45570/48461 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 11/28/18 Due Date: 1112019 ADM #03A-R SIN: 4.5570/48460 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 11/28/18 Due Date: 1112019 ADM #04-I. SIN: 41743/42456 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 11/28118 Due Date: 1112019 ADM #05-1. SIN: 41740142450 Heise Model: PPM-11 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 08/26/19 Due Date: 08/2020 ADM #05-R SIN: 41740/42447 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 08/28119 Due Date: 0812020 ADM 108-1 SIN: 41742142455 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 08/26/19 Due Date: 08/2020 ADM #07-I. SIN: 421 85142186 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 03/26/19 Due Date: 03/2020 ADM #07-R SIN: 42185/43326 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 03/26/19 Due Date: 03/2020 ADM #08-1 SIN: 42186143329 Heise Model: PPM-I Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Data: 03125119 Due Date: 03/2020 ADM #09-1. SIN: 42202/43351 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 01123/19 Due Date: 01/2020 ADM #09-R SIN: 42202/43350 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 01123/19 Due Date: 0112020 ADM 10-L SIN: 42203/43353 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 01/23/19 Due Date: 01/2020 ADM #11-L SIN: 43165144551-1 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 07/15/19 Due Date: 07/2020 ADM #11-R SIN: 43165/44730 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 07/15119 Due Date: 07/2020 ADM #12A-L SIN: 45605/48490 Heise Model: PPM-11 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 07116119 Due Date: 07/2020 ADM #13-I. SIN: 43415/45041 Heise Model: PPM-I Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 09/19/19 Due Date: 0912020 ADM #13-R SIN: 43415/45039 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 09119119 Due Date: 09/2020 ADM #14-L SIN: 43412/45045 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 09/19119 Due Date: 09/2020 ADM #15-1. SIN: 43418145042 Heise Model: PPM-i Mfgd by Dresser industries Calibrated by Ashcroft Calibration Date: 02/22/19 Due Date: 0212020 ADM #15-R SIN: 43416/45040 Heise Model: PPM-I Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 02/22/19 Due Date: 02/2020 ADM #16-1. SIN: 43413/45046 Heise Model: PPM-1 Mfgd by Dresser Industries Calibrated by Ashcroft Calibration Date: 02/21/19 Due Date: 0212020 ADM #17-I. SIN: 44579/46642 Heise Model: PPM-1 Mlgd & Calibrated by Ashcroft, Inc. Calibration Date: 05116119 Due Date: 05/2020 ADM #17-R SIN: 44579/46841 Heise Model: PPM-11 Mfgd & Calibrated by Ashcroft, Inc. Calibration Date: 05121/19 Due Date: 05/2020 ADM #18-L SIN: 44581/46846 Heise Model: PPM-I Mfgd & Calibrated by Ashcroft, Inc. Calibration Date: 05116119 Due Date: 05/2020 ADM #19-1. SIN: 44580/46844 Heise Model: PPM-1 Mfgd & Calibrated by Ashcroft, Inc. Calibration Date: 07/15/19 Due Date: 06/2020 ADM #19-R SIN: 44580/46843 Heise Model: PPM-1 Mfgd & Calibrated by Ashcroft, Inc. Calibration Date: 07/15/19 Due Date: 0612020 ADM #20-1. SIN: 44582/46848 Heise Model: PPM-1 Mfgd & Calibrated by Ashcroft, Inc. Calibration Date: 06/18/19 Due Date: 06/2020 #01-I., 03A-L, 05-I., 07-L, 09-L, 11-I., 13-L 15-1. I7-L, 19-I. Rated Accuracy: >0.07% Is (0.000175 in wc) Range: 0.0-0.25 in wc Res.: 0.00001 Uncertainty: <0.00035 #oi-R, 03A-R, 05-R, 07-R. 09-R, ii -R, 13-R, 15-R, 17-R, I9-R Rated Accuracy: >0.06% fs(0.003 in wc) Range: 0.0-5.0 In wc Res.: 0.0001 Uncertainty: <0.00348 #02-L, 04-I., 06-L, 08-I., 10.1_, 112A-L, I4 -I. 16-I., 18-I., 20-I. Rated Accuracy: >0.06% is (0.03 in wc) Range: 0.0-50.0 lnwc Res.:0.00I Uncertainty: <0.0346 Shortridge Instruments, Inc. 7855 East Redfield Road Scottsdale, Arizona 85260 (480) 991-6744 • Fax (480) 443-1267 • www.shortridge.com ADM Cal Stnds Rev 15110/14/19 1 of 2 10/14/19 - Shortridge Instruments, Inc. AirData Multimeter Calibration Equipment Customer Order Number, Meter Serial Number, and Test Type are referenced on page 1 LOW VELOCITY EQUIVALENT CONFIRMATION STANDARDS Vet Eqv Transfer Standard SIN: M02009 ModeliADM870C Vet Eqv Transfer Standard SIN: M02903 Model! ADM-870C Vel Eqv Transfer Standard SIN: M10839 Model! ADM-870C Vet Eqv Transfer Standard SIN: M10840 ModelADM-870C Vet Eqv Transfer Standard SIN: M10897 Model!ADM-870C Vet Eqv Transfer Standard SIN: M10901 Model! ADM-870C Vet Eqv Transfer Standard SIN: M13492 Model ADM-870C Vet Eqv Transfer Standard SIN: M19325 Model ADM-870C Rated Accuracy: Velocity 1.5% ± 3.5 fpm Mfgd & Calibrated by Shortridge Instruments, Inc. Mfgd & Calibrated by Shortridge Instruments, Inc. Mfgd & Calibrated by Shortridge Instruments, Inc. Mfgd & Calibrated by Shortridge Instruments, Inc. Mfg'd & Calibrated by Shortridge Instruments, Inc. Mfgd & Calibrated by Shortridge Instruments, Inc. M1g'd & Calibrated by Shortridge instruments, inc. Mfgd & Calibrated by Shortridge Instruments, Inc. Range: 100-5000 fpm Resolution: 0.1 Calibration Date: 12107/18 Due Date: 12/2019 Calibration Date: 12/07118 Due Date: 12/2019 Calibration Date: 12/07118 Due Date: 1212019 Calibration Date: 12/07/18 Due Date: 12/2019 Calibration Date: 01/17/19 Due Date: 01/2020 Calibration Date: 12/07118 Due Date: 12/2019 Calibration Date: 08108/19 Due Date: 08/2020 Calibration Date: 06/21119 Due Date: 06/2020 Uncertainty: <5.00 10m at 100 fpm; <7.50 fpm at 500 fpm TEMPERATURE STANDARDS RTD Simulator SIN: 249 Model RTD-1000/500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 03116118 Due Date: 0312020 RTD Simulator SIN: 250 Model RTD-1000/500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 03116/16 Due Date: 03/2020 RTD Simulator SIN: 253 Model RTD-1000/500 Mlgd by General Resistance Calibrated by lET Labs Calibration Date: 03/18/16 Due Date: 03/2020 RTD Simulator SIN: 254 Model RTD-1000/500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 04/07/16 Due Date: 0412020 RTD Simulator SIN: 258 Model RTD-1000/500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 04107/16 Due Date: 0412020 RTD Simulator SIN: 257 Model RTD-1000/500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 04107/16 Due Date: 04/2020 RTD Simulator SIN: 292 Model RTD-1000/500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 12121/15 Due Date: 1212019 RTD Simulator SIN: 293 Model RTD-1000/500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 12/21/15 Due Date: 12/2019 RTD Simulator SIN: 294 Model RTD-10001500 Mfgd by. General Resistance Calibrated by lET Labs Calibration Date: 12121/15 Due Date: 12/2019 RTD Simulator SIN: 313 Model RTD-1000/500 Mfgd! by General Resistance Calibrated by lET Labs Calibration Date: 03/16/18 Due Date: 03/2022 RTD Simulator SIN: 314 Model RTD-1000/500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 03116/18 Due Date: 0312022 RTD Simulator SIN: 315 Model RTD-1000/500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 03/16118 Due Date: 03/2022 RTD Simulator SIN: 316 Model RTD-10001500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 04/16/18 Due Date: 04/2022 RTD Simulator SIN: 317 Model RTD-1000/500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 04/16/18 Due Date: 04/2022 RTD Simulator SIN: 318 Model RTD40001500 Mfgd by General Resistance Calibrated by lET Labs Calibration Date: 04116118 Due Date: 04/2022 Rated Accuracy: 0.025% of setting Range: 100.000 to 11111.100 Resolution: 0.0111 Uncertainty: s 32 ppm Thermometer #1 SIN 8A089/Thermistor SIN A410660 Model 1504/5610 Mfgd by Hart Scientific Calibrated by Fluke Calibration Date: 08127/19 Due Date: 08/2021 Thermometer #2 SIN 88104/Thermistor SIN 871507 Model 150415610 Mfgd by Hart Scientific Calibrated by Fluke Calibration Date: 11/07/18 Due Date: 10/2020 Thermometer#5 SIN 811780/Thermistor SIN B10505 Model 1504/5610 Mfgd by Hart Scientific Calibrated by Fluke Calibration Date: 03107/19 Due Date: 0312021 Thermometer #8 SIN B11782lThermistor SIN B10509 Model 1504/5610 Mfgd by Hart Scientific Calibrated by Fluke Calibration Date: 02/20/18 Due Date: 02/2020 Thermometer #7 SIN 849938/ThermIstor SIN 8482202 Model 1504/5610 Mfgd and Calibrated by Fluke Calibration Date: 09/28/19 Due Date: 09/2021 Rated Accuracy(combined): 0.0324° F Range: 320 F to 176° F Resolution: 0.0010 F Combined Uncertainty with Baths: a 0.040° F Temp Transfer Standard SIN M00136 Model ADM-870 Mfgd & Calibrated by Shortridge Instruments, Inc. Calibration Date: 10102/19 Due Date: 10/2020 Temp Transfer Standard SIN M96100 Model ADM-870 Mfgd & Calibrated by Shortjidge Instruments, Inc. Calibration Date: 03/07/19 Due Date: 03/2020 Rated Accuracy: 0.03° F Range: 33° F to 158° F Resolution: 0.01° F Uncertainty: <0.023° F Total combined Uncertainty for MulliTemp and TemProbe testing: a0.046° F This form must remain with the Certificate of Calibration corresponding to the Customer Order Number and Meter Serial Number referenced on page 1. Shortridge Instruments, Inc. 7855 East Redfield Road Scottsdale, Arizona 85260 (480) 991-6744 • Fax (480) 443-1267 • www.shottridge.com ADM Cal Stnds Rev 15/10/14/19 2 of 2 10/14/19