HomeMy WebLinkAbout1905 CALLE BARCELONA; 238; AS110053; Permit. r
10/21/2020 AS110053 Permit Data
City of Carlsbad
Sprinkler Permit
Permit No: AS110053
1905 CALLE
Job Address: Status:. ISSUED
BARCELONA
Permit Type: SPRINK Applied 4/5/2011
Parcel No: 2550120400 Approved: 4/5/2011
Lot #: 0
Reference No.: • •
Issued: 4/5/2011
PC #: - Inspector:
Project Title: HAUTE YOGA FIRE SPRINKLER T.I. PLAN CHECK & INSPECTIONS
Applicant:. • • • Owner: •
TOTAL FIRE PROTECTION, INC. FOURTH QUARTER PROPERTIES XXX Li C
STE. 244 C/O THOMAS TROPEA •
1611-A S. MELROSE DR. 45 ANSLEY DR
VISTA, CA NEWNAN GA -
7607525-4329 • - • • • •
I
Fees ($)
•
Add'I Fees ($) Total ($) Balance ($)
130 • : • 130 0
Astl000
TrFeP
MATERIAL DATA SUBMITTAL
Haute Yoga T.I.
1905 Calle Barcelona, Suite 238
Carlsbad, CA 92009
Page Description Manufacturer
1-2 Sprinkler Piping ALLIED Dyna Thread Pipe
3-10 Sprinkler Piping TYCO Ductile Iron Fittings
11-12 Sprinkler Piping TYCO Mechanical Tee
13-16 Sprinkler TYCO RF-II Q.R. SSP
17 Pipe Hangers & Supports AFCON Fig 300 Ring
18 Pipe Hangers & Supports AFCON Fig 611 Ceiling Plate
19 Pipe Hangers & Supports AFCON Fig 655 All Thread Rod
20 Pipe Hangers & Supports SAMMY X-Press
Total Fire Protection, Inc.
1611A S. Melrose Dr. #244
Vista, Ca 92081
(760)525-4329 fax (877) 724-4329
C16-955387
tfpjohnc@gmail.com
DynawThread 00
Full Line Sch-40 Replacement
Dyna-Thread' offers the life expectancy of Sch40 with superior hydraulics and greater value.
Dyna-Thread sprinkler pipe represents an engineering advancement for the sprinkler pipe industry. It combines the safety
and longevity of traditional Sch-40 pipe with quality and superior hydraulic advantages.
Dyna-Thread's inside diameter is up
to 3.6% larger than Sch-40 giving it
superior hydraulics. And, when used
in combination with Dyna-Flow pipe,
down sizing often occurs.
Dyna-Thread is fully listed and
approved by UL, ULC, and FM for
fire sprinkler applications.
The life expectancy of Dyna-Thread
and Sch-40 are equal based on the
calculated wall thicknesses per UL.
The consistent quality of steel used to
make Dyna-Thread facilitates smooth
threading and lower maintenance
costs.
The exterior of Dyna-Thread is
protected by a clean, durable mill
coating for extended shelf life and
easy paint application.
(9 <~> @
Listed Approved Listed
With its increased strength and lighter
weight, Dyna-Thread reduces
installation fatigue and is ideal for
retro-fit applications.
Corrosion Resistance Ratio (CRR) is a
UL (Underwriters Laboratory) term for
the estimated life expectancy of a pipe
joint. This is based on the calculated
wall thickness at the base of the first
exposed thread, assumed to be the
weakest point of the pipe length. Dyna-
Thread and Sch-40 have the same
calculated wall thicknesses at this point
and are both assigned the same CRR of
1.00.
The internal surface of all black Allied
Tube & Conduit Fire Sprinkler pipe
products up to 4.5000" in diameter is
coated with our new Antibacterial
Formula, 'ABF'. In scientific laboratory
test, ABS proved to have superior
resistance to microbial colonization of
pipe walls, thereby delaying or possibly
preventing the onset of
Microbiologically Influenced corrosion
(MIC) when the First Sprinkler System
is first installed.
More wall thickness at the thread
(CR.R=1.00) gives Dyna-Thread
better life expectancy than lightwall
threadable pipe joints.
Unlike lightwall threadable pipe,
Dyna-Thread has no thread gauge
warning.
Dyna-Thread is approved for
standard hanger spacing (15 ft.
O.C.), can be used as earthquake
sway bracing, and is safe to use as
drops.
Dyna-Thread is safer to weld on.
Dyna-Thread is more widely
accepted than lightwall threadable
where Sch-40 is specified.
Super 40/Dyna-Thread pipe is
manufactured to meet: ASTM A-135,
Grade A and is in compliance with
NFPA- 13. All sizes of Super 40/Dyna-
Thread are rated at 300 psi working
pressure. Super 40/Dyna-Thread is UL
and ULC Listed for wet, dry deluge and
pre-action sprinkler systems and FM
Approved for use in wet systems. Super
40/Dyna-Thread can be "hot-dip"
galvanized to meet FM requirement for
dry systems. Super 40/Dyna-Thread is
approved for all threaded couplings and
welded outlets and is suitable for all
roll-grooved, and plain-end fittings.
(See listing information).
Specifications
NPS Nominal I.D. M. M. (H20 Riled) Pc Wtgtilt (21') WlIUft (24') WULIft (25')
In; mm In; mm Lbs/Ft; Kg/rn Lbs/Ft; Kg/rn Lift Lbs; Kg Lbs; Kg Lbs; Kg
1.080 1.330 1.75 70 1955 2234 232
25 27.4 2.0 2.60 70 887 1013 1056
1%' 1.408 1.870 2.54 51 2002 2288 2384
32 35.8 2.8 3.78 51 908 1038 108
1W 1.639 2.290 3.22 44 2115 2418 2511
40 41.6 3.4 4.79 44 959 1097 114
2.104 3.050 4.57 30 1921 2196 228
50 53.4 4.5 6.80 30 871 996 103
tw o/Flow Control () allied 16100 S. Lathrop• Harvey, IL 60426
11350 Norcom Rd. Philadelphia, PA 19154
TUBE& CONDUIT 2525 N. 27th Ave. • Phoenix, AZ 85009
Customer Service: 1 (800) 882-5543
Fax 708-339-1806
S3-3
Submittal Data Sheet
Dyna-Th read°
Full Line Sch-40 Replacement
Slamp Here
Dyna-Thread sprinkler pipe represents an engineering advancement for the sprinkler
pipe industry. It combines the safety and longevity of traditional Sch-40 pipe with
quality and superior hydraulic advantages.
Comparison to Schedule 40 Dyna-Threads inside diameter is up to 3.6% larger than
Sch40 giving it superior hydraulics. Also, when used in combination with Dyna-Flow
pipe, down sizing often occurs. Dyna-Thread is fully listed and approved UL, ULC,
and FM for fire sprinkler applications. The life expectancy of Dyna-Thread and Sch-40
are equal based on the calculated wall thicknesses per UL. The consistent quality of
steel used to make Dyna-Thread facilitates smooth threading and lower maintenance
costs. The exterior of Dyna-Thread is protected by a clean, durable mill coating for
extended shelf life and easy paint application. With its increased strength and lighter
weight, Dyna-Thread reduces installation fatigue and is ideal for retro-fit applications.
Corrosion Resistance Ratio (CRR) is a UL (Underwriters Laboratory) term for the
estimated life expectancy of a pipe joint. This is based on the calculated wall thickness
at the base of the first exposed thread, assumed to be the weakest point of the pipe
length. Dyna-Thread and Sch-40 have the same calculated wall thicknesses at this
point and are both assigned the same CRR of 1.00.
Comparison to L.W.T. Pipe More wall thickness at the thread (CRR= 1.00) gives
Dyna-Thread better life expectancy than lightwall threadable pipe joints. Unlike
lightwall threadable pipe Dyna-Thread has no thread gauge warning. Dyna-Thread is
approved for standard hanger spacing (15 ft. O.C.), can be used as earthquake sway
bracing, and is safe to use as drops. Dyna-Thread is safer to weld on than many zinc-
coated lightwall threadable pipe products. Dyna-Thread is more widely accepted than
lightwall threadable where Sch40 is specified.
Specifications & Approvals Super 40/
Dyna-Thread pipe is manufactured to
meet: ASTM A 135, Grade A and is in
compliance with NFPA-13. All sizes of
Super 40lDyna-Thread are rated at 300
psi working pressure. Super 40/ Dyna-
Thread is UL and ULC Listed for wet,
dry and pre-action sprinkler systems and
FM Approved for use in wet systems.
Super 40/Dyna-Thread can be "hot-dip"
galvanized to meet FM requirement for
dry systems. Super 40/Dyna-Thread is
approved for all threaded couplings and
welded outlets and is suitable for all roll-
Specifications
NPS Nominal I.D. WI. WI. (H20 Filled) Pcs/ WULIII (21') WUUft (24') WVLiII (25')
In; mm In; mm LbsIFt; Kg/rn LbslFt; Kg/rn Lift Lbs; Kg Lbs; Kg Lbs; Kg
1.080 1.330 1.75 70 1955 2234 232
25 27.4 2.0 2.60 70 887 1013 105
1'/4' 1.408 1.870 2.54 51 2002 2288 2384
32 35.8 2.8 3.78 51 908 1038 108
1½' 1.639 2.290 3.22 44 2115 2418 2511
40 41.6 3.4 4.79 44 959 1097 114
2.104 3.050 4.57 30 1921 2196 228
50 53.4 4.5 6.80 30 871 996 103
grooved, and plain-end fittings. (See American Tube and Pipe was acquired by Allied Tube and Conduit on February 1,
listing information). 1997. The engineered lightwall and standard wall family of products although they
The internal surface of all black Fire have different names are the same in all respects with regard to strength, weight,
Sprinkler pipe up to 4.5000" in diameter bundle count, listings and approvals. For example,
shall be coated with Allied Tube & Dyna-Flow and Super Flo are the same product as
are Dyna Thread and Super 40. XL is manufactured (Zjj Conduit Antibacterial Formula 'ABF". with Exterior galvanized coating. BIT is Listed Approved Listed manufactured with Black lacquer coating.
Project: Sprinkler Contractor: Date:
Engineer: Specification Reference: System Type:
Locations: Comments: (:IIIII) S3 -4
t'1C0/ Fire & Building
/ Products
Technical Services: Tel: (800) 381-9312/ Fax: (800) 791-5500
Pipe Fittings
NPT Threaded,
Ductile Iron
General
Description
The Tyco° Series 800 Threaded Pipe
Fittings and California Tees & Elbows
are manufactured from ductile iron.
They are stronger and more corrosion
resistant than cast iron fittings. The
additional strength is provided by the
ductile properties and by adding mag-
nesium while the iron is being poured
into the final cast shape. Although
tighter than standard cast iron, the fit-
tings have an added advantage of be-
ing less susceptible to cracking due to
their added strength.
The Series 800, California, and Figure
719 Threaded Pipe Fittings are a re-
designation for the Central Series 800,
California, and Figure 719 Threaded
Pipe Fittings.
WARNINGS
The Threaded Pipe Fittings described
herein must be installed and main-
tained in compliance with this docu-
ment, as well as with the applicable
standards of the National Fire Pro-
tection Association, in addition to the
standards of any other authorities hav-
ing jurisdiction. Failure to do so may
impair the performance of these
devices.
The owner is responsible for maintain-
ing their fire protection system and de-
vices in proper operating condition.
The installing contractor or sprinkler
manufacturer should be contacted
with any questions.
Technical
Data
Approvals:
UL Listed and FM Approved
Maximum Working Pressure:
Series 800 and California Fittings:
250 psi (17,2 bar)
Figure 719 Plug:
250 psi (17,2 bar)
Material:
Series 800 and California Fittings:
Ductile Iron
Figure 719 Plug:
Cast Iron
Pipe Thread:
NPT per ANSI B1.20.1
Installation
Apply Teflont tape or high quality pipe
joint compound on mate pipe threads
and tighten two to three turns beyond
hand tight.
NOTE
Installers who have not used ductile
iron threaded fittings should be in-
structed that the fittings are stron-
ger than the pipe and overtightening
the fitting can create leaks and cause
damage to pipe threads. In general,
there Is about one-half turn difference
between cast iron and ductile iron fit-
tings. Apply Teflon tape or high qual-
ity pipe joint compound on the male
pipe threads and tighten two to three
turns beyond hand tight. If an auto-
matic make-on machine is being used,
please exercise caution in setting the
machine to the proper parameters pri-
or to tightening fittings onto the male
pipe threads.
Limited
Warranty
Products manufactured by Tyco Fire
& Building Products (TFBP) are war-
ranted solely to the original Buyer for
ten (10) years against defects in mate-
rial and workmanship when paid for
and properly installed and maintained
under normal use and service. This
warranty will expire ten (10) years from
date of shipment by TFBP. No warran-
ty is given for products or components
manufactured by companies not af-
filiated by ownership with TFBP or for
products and components which have
been subject to misuse, improper in-
stallation, corrosion, or which have not
been installed, maintained, modified or
repaired in accordance with applicable
Standards of the National Fire Protec-
tion Association, and/or the standards
of any other Authorities Having Juris-
diction. Materials found by TFBP to be
defective shall be either repaired or re-
placed, at TFBP's sole option. TFBP
neither assumes, nor authorizes any
person to assume for it, any other ob-
ligation in connection with the sate of
products or parts of products. TFBP
shall not be responsible for sprinkler
system design errors or inaccurate or
incomplete information supplied by
Buyer or Buyer's representatives.
In no event shall TFBP be liable, in
contract, tort, strict liability or under
any other legal theory, for incidental,
indirect, special or consequential dam-
ages, including but not limited to labor
charges, regardless of whether TFBP
was informed about the possibility of
such damages, and in no event shall
TFBP's liability exceed an amount
equal to the sales price.
The foregoing warranty is made in lieu
of any and all other warranties. ex-
oress or implied. including warranties
of merchantability and fitness for a
narticular ouroose.
This limited warranty sets forth the ex-
clusive remedy for claims based on
failure of or defect in products, materi-
als or components, whether the claim is made in contract, tort, strict liability
or any other legal theory.
This warranty will apply to the full ex-
tent permitted by law. The invalidity,
in whole or part, of any portion of this
warranty will not affect the remainder.
Ordering
Procedure
When placing an order, indicate the
full product name. Please specify the
quantity, figure number, wall thickness,
and size.
tregjsred trademark of E. I. du Pont de
Nemours and Company or its affiliates.
TFPI7IO Page 1 of 10 JANUARY, 2008
Nominal Pipe Figure 813 Size
ANSI A Approx.
Inches Inches Weight Part
ON (mm)
Lbs. Number
(kg)
1/2 1.13 0.22 86780 DN15 (28,7) (0,09)
3/4 1.31 0.33 86781 0N20 (33,3) (0,15)
1 1.50 0.48 86280 DN25 (38,1) (021)
1-1/4 1.75 0.73 86281 DN32 (44,5) (0,33)
1-1/2 1.94 0.93 86282 DN40 (49,3) (0,42)
2 2.25 1.55 86283 DN50 (57,1) (0,70)
2-1/2 2.69 2.70 86782 0N65 (68,3) (1.22)
FIGURE 811 FIGURE 813
90° ELBOW 450 ELBOW
1.44
Figure 811
B Approx. A B
Inches Weight Part Inches Inches
(mm)
Lbs. Number (mm) (mm)
(kg)
0.56 0.24 86206 0.88 0.38
(14,2) (0111) (22,4) (9,7)
0.75 0.40 86205 1.00 0.44
(19.0) (0.18) (25.4) (11,2)
0.81 0.64 86200 1.13 0.81
(20,6) (00) (28,7) (20,6)
1.06 0.95 86201 1.31 0.63
(26,9) (0,43) (33,3) (16,0)
1.19 1.24 86202
0.69
(30.2) (0,56) (36,6) (17,5)
1.50 1.74 86203 1.68 0.94
(38,1) (0179) (42,7) (23,9)
1.56 3.28 86204 1.94 1.00
(39,6) (1,49) (49,3) (25,4)
TABLE I
NOMINAL DIMENSIONS FIGURES 811 & 813
Page 2of 10 TFPI7I0
TFPI7IO Page 3 of 10
FIGURE 812
900 REDUCING ELBOW
Nominal Pipe Figure 812 Size
ANSI A B C D Approx.
Weight Part Inches Inches Inches Inches Inches Lbs. ON (mm) (mm) (mm) (mm) Number
(kg)
3/4 x 1/2 1.19 1.19 0.63 0.63 0.33 86342 DN20 x 15 (30.2) (30,2) (16,0) (16,0) (0,15)
I x1/2 1.25 1.38 0.56 0.81 0.44 86210 0N25 x 15 (31,8) (35,1) (14,2) (20.6) (0.20)
1 x3/4 1.38 1.44 0.69 0.88 0.53 86211 0N25 x 20 (35,1) (36,6) (17,5) (22,4) (0,24)
1-1/4x 1/2 1.31 1.50 0.63 0.94 0.64 88212 DN32 x 15 (33,3) (38,1) (16,0) (23,9) (0,29)
1-1/4 x 3/4 1.44 1.63 0.75 1.06 0.75 86213 0N32 x 20 (36,6) (41.4) (19,0) (26,9) (0,34)
1-1/4x1 1.56 1.68 0.88 1.00 0.77 86214 DN32 x 25 (39.6) (42,7) (22,4 (25,4) (0,35)
1-1/2 * 3/4 1.50 1.75 075 1.19 0.95 86221 DN40 *20 (38,1) (44,4) (19,0) (30.2) (0,43)
1-1/2* 1 1.63 1.81 0.88 1.13 0.99 86215 DN40 x 25 (41,4) (46,0) (22,4) (28.7) (0,45)
1.1/2*1-1/4 1.81 1.88 1.13 1.19 1.14 86216 DN40 x 32 (46.0) (47,8) (28.7) (30.2) (0,52)
2*3/4 1.63 1.94 0.88 1.38 1.39 86217 DN50x20 (41,4) (49,3) (22,4) (35,1) (0,63)
2*1 1.75 2.06 2.00 1.31 1.58 86218 DN5O *25 (44,4) (52,3) (50,8) (33,3) (0,72)
2*1-1/2 2.00 2.19 1.25 1.44 1.67 86220 DN50x40 (50,8) (55,6) (31,8) (36,6) (0.76)
2-1/2*2 2.38 2.63 1.25 1.88 3.01 86262 DN65 x 50 (60,5) (66,8) (31,8) (47,8) (1,36)
TABLE 2
NOMINAL DIMENSIONS FIGURE 812
(D
TFPI7I0 Page 5of 10
LB!UJii
FIGURE 814 FIGURE 818
IRON TEE STRAIGHT COUPLING
Figure 814 Figure 818
A B Approx. A B
Inches Inches Weight
Lbs.
Part
Number Inches Inches
(mm) (mm) (kg)
(mm) (mm)
1.13 0.56 0.33 86340 1.38 0.31
(28,7) (14,2) (0.15) (35,1) (Z9)
1.31 0.75 0.50 86341 1.63 0.56
(33,3) (19,0) (0,23) (41.4) (14,0)
1.50 0.81 0.85 86230 1.75 0.38
(36,1) (20,6) (0,38) (44,4) (9,7)
1.75 1.06 1.30 86231 2.00 0.56
(44,4) (26,9) (0,59) (50,8) (14,0)
1.94 1.19 1.63 86232 2.19 0.75
(49,3) (30.2) (0.74) (55,6) (19,0)
2.25 1.50 2.63 86233 2.63 1.13
(57,1) (38,1) (1119) (66,8) (28,7)
2.69 1.56 455 86234 3.00 0.75
(68,3) (39,6) (2,06) (76,2) (19,0)
TABLE 4
NOMINAL DIMENSIONS FIGURES 814 & 818
Nominal Pipe
Size
Approx.
ANSI Inches
ON
Weight
Lbs.
Part
Number
(kg)
1/2 0.18 72779 0N15 (0,08)
3/4 0.26 72778 DN20 (Oil)
1 0.44 72755 0N25 (0,20)
1-1/4 0.54 72754 DN32 (0,24)
1-1/2 0.71 72753 DN40 (0,32)
2 1.15 72752 0N50 (0,52)
2-1/2 2.29 72758 DN65 (1,04)
TFPI7I0 Page 6of 10
Page 7 of 10 TFPI7IO
FIGURE 815
REDUCING TEE
Nominal Pipe Size Figure 815
A B C D E F Approx.
ANSI Inches Inches Inches Inches Inches Inches Inches Weight Part
DN (mm) (mm) (mm) (mm) (mm) (mm) Lbs. Number
(kg)
1-1/2 x 1-1/4 x 1/2 1.44 1.31 1.69 0.69 0.63 1.13 1.03 86257 DN40 x 32 x 15 (36.6) (33.3) (42.9) (17.5) (16.0) (28.7) (0.47)
1-1/2 x 1-1/4 x 3/4 1.50 1.44 1.75 0.75 0.75 1.19 1.10 86258 DN40 x 32 x 20 (38.1) (36.6) (44.5) (19.0) (19.0) (30.1) (0.50)
1-1/2 x 1-1/4 x 1 1.63 1.56 1.81 0.88 0.88 1.13 1.31 88259 0N40 x 32 x 25 (41.4) (39.7) (46.0) (22.4) (22.4) (28.7) (0.59)
1-1/2x1-1/4x2 2.19 2.13 2.00 1.44 1.44 1.25 1.94 86260 DM0 x 32 x 50 (55.6) (54.1) (50.8) (36.6) (36.6) (57.1) (0,88)
1-1/2 x 1-1/2 x 1/2 1.44 1.44 1.69 0.69 0.69 1.13 1.14 86261 DN40 x 40 x 15 (36.6) (36.6) (42,9) (17.5) (17.5) (28.7) (0.52) _______
1-1/2x1-1/2x314 1.50 1.50 1.75 0.75 0.75 1.19 1.23 86262 0N40 x 40 x 20 (38.1) (38.1) (44.4) (19.0) (19.0) (30.1) (0.56)
1-1/2 x 1-1/2 x 1 1.63 1.63 1.81 0.88 0.88 1.13 1.38 86263 DN40 x 40 x 25 (41.2) (41.2) (46.0) (22.4) (22.4) (28.7) (0.62)
1-1/2x1-1/2x1-1/4 1.81 1.81 1.88 1.06 1.06 1.19 1.50 86264 0N40 x 40 x 32 (46.0) (46.0) (47.6) (27.0) (27.0) (30.1) (0,68)
1-1/2 x 1-1/2 x 2 2.19 2.19 2.00 1.44 1.44 1.25 2.00 86265 DN40x40x50 (55,5) (55,5) (50.8) (36.6) (36.6) (31.7) (0.91)
2x1 x2 2.25 2.00 2.25 1.50 1.31 1.50 2.18 86266 DN50 x 25 x 50 (57.2) (50,8) (57.2) (38.1) (33.3) (38.1) (0,99)
2x1-1/4x2 2.25 2.13 2.25 1.50 1.44 1.50 2.31 86267 DN50x32x50 (57.2) (54.1) (57.2) (38.1) (36.6) (38.1) (1.05)
2 x 1-1/2 x 1/2 1.50 1.44 1.88 0.75 0.69 1.31 1.50 86268 DN50 x 40 x 15 (38.1) (36.6) (47.8) (19.0) (17.5) (33.3) (0.68)
2x1-1/2x3/4 1.63 1.50 1.94 0.88 0.75 1.38 1.61 86269 DN50x40x20 (41.4) (38.1) (49.3) (22.4) (19.0) (35.0) (0.73)
2x1-1/2x1 175 1.63 2.00 1.00 0.88 1.31 I 86270 DN50 x 40 x 25 (44.5) (41.4) (50.8) (25.4) (22,4) (33.3) (0.75)
2 x 1-1/2 x 1-1/2 2.06 1.94 2.19 1.31 1.19 1.44 2.03 86272 DN50 x 40 x 40 (52.4) (49.2) (55.5) (33,3) (30.2) (36,6) (0.92)
2x1-1/2x2 2.25 2.19 2.50 1.50 1.44 1.50 2.37 86273 0N50 x 40 x 50 (57.1) (55.5) (63.5) (38,1) (36,6) (38,1) (1.07)
2 x 2 x 1/2 1.50 1.50 1.88 0.75 0.75 1.31 1.50 86222 DN50 x 50 x 15 (38,1) (38.1) (47,8) (19,0) (19.0) (33.3) (0,68)
2 x 2 x 3/4 1.63 1.63 1.94 0.88 0.88 1.38 1.67 86223 DN50 x 50 x 20 (41.4) (41,4) (49.3) (22.4) (22.4) (35.0) (0,76)
2x2x1 1.75 1.75 2.00 1.00 1.00 1.31 1.91 86224 DN50 x 50 x 25 (44,5) (44.5) (50.8) (25,4) (25.4) (33,3) (0.86)
2 x 2 x 1-1/4 1.88 1.88 2.13 1.13 1.13 1.44 2.05 86225 DN50 x 50 x 32 (47,8) (47,8) (54,1) (28.7) (28.7) (36.6) (0.93)
2 x 2 x 1-1/2 2.00 2.00 2.19 1.25 1.25 1.50 2.11 86226 DN50 x 50 x 40 (50.8) (50.8) (55.6) (31.8) (31,8) (38.1) (0.96) _______
2x2x2-1/2 2.63 2.63 2.38 1.75 1.88 1.44 3.67 86227 DN50x50x65 (66.8) (66.8) (60.5) (44,5) (47.8) (36.6) (1.66) _
2-1/2 x 2 x 314 1.75 1.63 2.31 0.63 0.88 1.75 2.22 86274 DN65 x 50 x 20 (44,5) (41.4) (58.7) (15.9) (22.4) (44.5) (1,01)
TABLE 5(2 0F2)
NOMINAL DIMENSIONS FIGURE 815
Page 8 of 10 TFPI7IO
1FJTLi
FIGURE 820 FIGURE 830 FIGURE 719
CAP BRASS SEAT UNION PLUG
Nominal Pipe Figure 820 Figure 830 Figure 719 Size
ANSI A Approx. A B Approx. A Approx.
Inches Inches Weight Part Inches Inches Weight Part Inches Weight Part
ON (mm)
Lbs. Number (mm) (mm) Lbs. Number (mm) Lbs. Number
(kg) (kg) (kg)
1/2 0.88 0.15 72776 1.88 0.81 0.47 86207 094 0.10 86292 DN15 (22,4) (0,06) (47.8) (20,6) (0,21) (23,9) (0,04)
3/4 1.00 0.22 72777 2.00 0.94 0.66 86275 1.13 0.18 86293 0N20 (25,4) (0110) (50,8) (23,9) (0,30) (28,7) (0.08)
1
DN25
1.18
(30,0)
0.33
(0115) 72824 2.19
(55.6)
0.81
(20,6)
1.08
(0,49) 86276 1.25
(31,7)
0.28
(0,13) 86294
1-1/4
DN32
1.31
(33,3)
0.54
(0.24) 72756 2.50
(63,5)
1.06
(26,9)
1.54
(0,70) 86277 1.38
(35,1)
0.50
(0,23) 86295
1-1/2 1.38 0.68 72822 2.63 1.19 2.03 86278 1.44 0.70 86296 0N40 (35.1) (0,31) (66.8) (30,2) (0,92) (36,6) (0,32)
2 1.50 0.96 72823 3.13 1.63 3.15 86279 1.50 0.90 86297 DN50 (38.1) (0,43) (79,5) (41,4) (1,43) (38,1) (0,41)
2.1/2 1.75 1.80 72825 - - - - - T - 0N65 (44,5) (0,82)
TABLE 6
NOMINAL DIMENSIONS FIGURES 820, 830 & 719
TFPI7IO Page 9 of 10
I!" t ftJf7
FIGURE 825
EXTENSION PIECE
FIGURE 827
HEX BUSHING
FIGURE 816
REDUCING COUPUNG
Nominal Pipe Figure 825 Figure 827 Figure 816
Size Extension Piece Hex Bushing Reducing Coupling
A Approx. A Approx. A B ANSI Inches Inches Weight Part inches Weight Part Inches Inches Weight Part
ON
(mm)
Lbs. Number (mm) Lbs. Number (mm) (mm) Lbs. Number
(kg) (kg) (kg)
1/2x1/2 1.50 0.20
72751 - - - - - - - DN15 x 15 (38,1) (0,09)
1/2 x 1/2 2.00 0.27
72980 - - - - - - - DN15 x 15 (50,8) (0,12)
3/4 x 3/4 1.50 0.22 72981 - - - - - - - DN20 x 20 (38,1) (0,10)
3/4 x 3/4 2.00 0.31 73982 - - - - - - - DN20 x 20 (50,8) (0,14)
3/4 x 1/2 1.75 0.69 0.38 86772 DN20 xiS - - - - - - (43,2) (17,5) (0,17)
I x1/2 1.06 0.22 72726 1.69 0.50 0.38 86228 DN25 x 15 - - - (26,9) (0,10) (42,9) (12,7) (0,17)
1 x3/4 1.06 0.18 72762 1.75 0.50 0.53 86229 DN25 x 20 - - - (26,9) (0,08) (43,2) (12,7) (0,24)
1-114x1 1.19 0.31 72763 - - - - DN32 x 25 - - - (30,2) (0,14)
1-1/2x1 1.25 0.53 72757 - - - - DN40 x 25 - - - (31,7) (0.24)
1-1/2x1-1/4 1.25 0.35 72764 - - - - DN40x32 - - (31,7) (0,10)
2x1 1.38 0.75 72759 - - - - DN50 x 25 - - - (35,1) (0,34)
2x 1-1/4 1.38 0.69 72761 - - - - DN50x32 - - - (35,1) (0.31)
2 x 1-1/2 1.38 0.62 72775 - - - - DN50x40 - - - (35,1) (0,28)
TABLE 7
NOMINAL DIMENSIONS FIGURE 825,827 & 816
(B
tqC0 /Fire & Building
I Products
Technical Services: Tel: (800) 381-9312/ Fax: (800) 791-5500
www.tyco-fire.com
Orirniell grooved Fire Protection Products
Figure 40-5
Strap
General
Description
rJJ
U L iC See Fire Protection
Submittal Sheet for FM Pressure Rating and
Listing/Approval Information
The Figure40-5 Strap is an economical alternative
to welded pipe outlets on steel pipe.
The Figure 40-5 Strap may be used with full
lengths of pipe and eliminates threading and
welding, decreasing waste and installation time.
The 40-5 Strap may be used in wet, dry pipe and
deluge systems.
WARNING
The Figure 40-5 Strap described herein must be
installed and maintained in compliance with this
document, aswellas with theapplicablastandards
of the National Fire Protection Association, in
addition to the standards of any otherauthorities
ha ving jurisdiction. Failure to do so may impair
the performance of this device.
The owner is responsible for maintaining their
fire protection system and devices in proper
operating condition. The installing contractor or
sprinklermanufacturershould be contacted with
any questions.
Technical
Data
Figure: 40-5
Outlet: Threaded
Approvals: UL, FM, ULC, and VdS;
See Fire Protection Submittal Sheet for exact
Listing /Approval information.
Housing: Ductile iron conforming to
ASTM A-536, Grade 65-45-12
Protective Coatings:
'Clear rust inhibitive coaling
Zinc electroplated conforming to
ASTM B-633, Type Ill Service 2 (optional)
U-Boll: Carbon steel conforming to
ASTM A-307, Grade A, Zinc electroplated
Nuts: Carbon steel conforming to
ASTM A-307, Grade A, Zinc electroplated
Gasket: (specify when ordering)
Grade "E" EPDM green color code.
(See Data Sheet TFP1895 for aid in selecting
proper gasket)
Ordering
Procedure
When placing an order, indicate the full product
name. Please specifythe quantity, figure number,
type of gasket, Grade "E" EPDM, and size.
Grinnell Grooved Piping Products, valves,
accessories and other products are available
throughoutthe U.S., Canada, and internationally,
through a network of distribution centers. You
may write directly or call 215-362-0700 for the
distributor nearest you.
Care and
Maintenance
The owner is responsible for the inspection,
testing, and maintenance of their lire protection
system and devices in accordance with the
applicablestandards of the National Fire Protection
Association (e.g., NFPA 25), in addition to the
standards of any authority having jurisdiction.
The installing contractororproductmanufacturer
should be contacted relative to any questions.
Any impairment must be immediately corrected.
It is recommended that automatic sprinkler
systems be inspected, tested, and maintained by
a qualified Inspection Service.
Limited
Warranty
Products manufactured by Tyco Fire Products are
warranted solely to the original Buyer for ten (10)
years against defects in material and workmanship
when paid brand property installed and maintained
under normal use and service. This warranty will
expireten (10) years from date of shipment byTyco
Fire Products. No warranty is given for products or
components manufactured by companies not
affiliated by ownershipwithlyco Fire Products orfor
products and componentswhich have been subject
to misuse, improperinstallation, corrosion, orwhich
have not been installed, maintained, modified or
repaired in accordance with applicable Standards of
the National Fire Protection Association (NFPA),
andlorthe standards ofanyotherAuthoritiesHaving
Jurisdiction. Materials found by Tyco Fire Products
to be defective shall be either repaired or replaced, at
Tyco Fire Products' sole option. Tyco Fire Products
neither assumes, nor authorizes any person to.
assumeforlt,anyotherobligationinconnectionwith
the sale of products or parts of products. Tyco Fire
Productsshallnotberesponslbleforsprinklersystem
deslgnerrorsorinaccurateorincompleteinfomiation
supplied by Buyer or Buyers representatives.
IN NO EVENT SHALL TYCO FIRE PRODUCTS BE
LIABLE, IN CONTRACT, TORT, STRICT LIABILITY
OR UNDER ANY OTHER LEGAL THEORY, FOR
INCIDENTAL, INDIRECT, SPECIAL OR
CONSEQUENTIALDAMAGES, INCLUDING BUTNOT
LIMITED TO LABOR CHARGES, REGARDLESS OF
WHETHER1YCOFIREPRODUCTSWASINFORMED
ABOUT THE POSSIBILITY OF SUCH DAMAGES,
AND IN NO EVENTSHALLIYCO FIRE PRODUCTS'
LIABILITY EXCEED AN AMOUNT EQUAL TO THE
SALES PRICE
Page 1 of 2 September 2004
(B
TFPI72O
Pipe Nominal Dimensions Hole Net
Size Size Wt. A B C D
Run x Inches Inches Inches Inches Inches Lbs.
Branch mm mm mm mm mm Kg.
1'/4" x i,n 2.00 1.50 3.50 1.20 0.84
50.8 38.1 88.9 30.5 30.2 0.4
1,4' x s,su 2.00 1.50 3.50 1.20 1 r. 0.88
50.8 38.1 88.9 30.5 30.2 0.4
iv: x r 2.31 1.68 3.50 1.20 1.13
58.7 42.7 88.9 30.5 30.2 0.5
11/20 , 2.12 1.62 3.50 1.32 11%6 0.84
53.8 41.1 88.9 33.5 30.2 0.4
11/20 x 3/0 2.12 1.62 3.50 1.32 1/i r, 0.88
53.8 41.1 1 88.9 33.5 30.2 0.4
ih/2 x 1 2.43 1.80 3.50 1.32 13/1 r, 1.13
61.7 45.7 88.9 33.5 30.2 0.5
2" x /2" 2.36 1.86 3.74 1.55 13't6 0.88
59.9 47.2 95.0 39.4 30.2 0.4
2" x 3/0 2.36 1.86 3.74 1.55 13',6 0.95
59.9 47.2 95.0 39.4 30.2 0.4
2"X i" 2.67 2.04 3.74 1.55 1/i 1.16
67.8 51.8 95.0 39.4 30.2 0.5
21/2" X 1/2 2.61 2.11 4.25 1.80 1/is 0.90
66.3 53.6 108.0 45.7 30.2 0.4
21/2" X3/4" 2.61 2.11 4.25 1.80 13'i6 0.99
66.3 53.6 108.0 45.7 30.2 0.4
2'!? x r 2.92 2.29 4.25 1.80 1/t& 1.21
74.2 58.2 108.0 45.7 30.2 1 0.5
Item Description
1 Housing
2 Gasket
3 Flanged Nut
4 U-Bolt
Fitting
Size
Equivalent Length
(1 inch pipe)
1114"X V 8
11/2"X 1" 6
2"x 1" 6
21/?x 1' r 4
The friction loss for these outlets is specified in
equivalent length of 1 inch Schedule 40 (C=120) pipe.
Page 2 of 2 TFPI 720
Figure 40-5 Strap
The 1 inch outlets can be used with a nipple leading Note: Outlet threads conforming to ISO 7-1 are available, contact
directly to a sprinkler. These fittings should be used Tyco Fire Products.
for hydraulically calculated systems only.
12
General Notes: It is the Designer's responsibility to select products suitable for the intended service and to ensure ISO that pressure ratings and performance data is not exceeded. Always read and understand the installation 9001 instructions (lH.1 000). Never remove any piping component or correct or modify any piping deficiencies without
first depressurizing and draining the system. Material and gasket selection should be verified to be compatible
for the specific application. . Certified Company
TYCO FIRE PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19946 Printed U.S.A.
tqCU /Fire & Building
I Products
Technical Services: Tel: (800) 381-9312 I Fax: (800) 791-5500
Series RFII - 5.6 K-factor
"Royal Flush III"' Pendent Concealed Sprinklers
Quick & Standard Response, Standard Coverage
General
Description
The Series RFII Quick Response
(3 mm bulb) & Standard Response (5
mm bulb), 5.6 K-Factor, "Royal Flush
II" Concealed Pendent Sprinklers are
decorative sprinklers featuring a flat
cover plate designed to conceal the
sprinkler. It is the best choice for archi-
tecturally sensitive areas such as hotel
lobbies, office buildings, churches,
and restaurants.
Each unit includes a Cover Plate As-
sembly that conceals the sprinkler op-
erating components above the ceiling.
The separable two-piece design of the
Cover Plate and Support Cup Assem-
blies allows installation of the sprin-
klers and pressure testing of the fire
protection system prior to installation
of a suspended ceiling or application
of the finish coating to a fixed ceiling.
They also permit removal of sus-
pended ceiling panels for access to
building service equipment without
having to first shut down the fire pro-
tection system and remove sprinklers.
Also, the separable two-piece design
of the the Sprinkler provides for 1/2
inch (12,7 mm) of vertical adjustment,
to reduce the accuracy to which the
length of fixed pipe drops to the sprin-
klers must be cut.
The Series RFII Sprinklers are
shipped with a Disposable Protective
IMPORTANT
Always refer to Technical Data
Sheet TFP 700 for the "INSTALLER
WARNING" that provides cautions
with respect to handling and instal-
lation of sprinkler systems and com-
ponents. Improper handling and in-
stallation can permanently damage
a sprinkler system or its compo-
nents and cause the sprinkler to fall
to operate in a fire situation or cause
it to operate prematurely.
Cap. The Protective Cap is temporarily
removed for installation, and then it
can be replaced to help protect the
sprinkler while the ceiling is being in-
stalled or finished. The tip of the Pro-
tective Cap can also be used to mark
the center of the ceiling hole into plas-
ter board, ceiling tiles, etc. by gently
pushing the ceiling product against the
Protective Cap. When the ceiling in-
stallation is complete the Protective
Cap is removed and the Cover Plate
Assembly installed.
As an option, the Series RFII Standard
Response (5 mm bulb) "Royal Flush II"
Concealed Pendent Sprinklers may be
fitted with a silicone Air and Dust Seal
(Ref. Fig. 5). The Air and Dust Seal is
intended for sensitive areas where it is
desirable to stop air and dust travel
through the cover plate from the area
above the ceiling.
WARNINGS
The Series RFII Concealed Pendent
Sprinklers described herein must be
installed and maintained in compli-
ance with this document, as well as
with the applicable standards of the
National Fire Protection Association,
in addition to the standards of any
other authorities having jurisdiction.
Failure to do so may impair the per-
formance of these devices.
The owner is responsible for maintain-
ing their fire protection system and de-
vices in proper operating condition.
The installing contractor or sprinkler
manufacturer should be contacted
with any questions.
Model/Sprinkler
Identification
Numbers
111355 (5 mm bulb)
1(3mm bulb)I
Technical
Data
Approvals for Series RFII
UL and C-UL Listed. FM Approved.
NYC under MEA 353-01-E. LPCB
(Ref. No. 094a/09 for TY3551 &
094a/10 for TY3531) Approved.
The approvals apply only to the serv-
ice conditions indicated in the Design
Criteria section.
Approvals for Air & Dust Seal
(Part #1 0908100)
UL and C-UI Listed for use with the
RFII (TY3551) Standard Response
Concealed Sprinkler.
Maximum Working Pressure:
Maximum 250 psi (17,3 bar) by UL,
C-UL, and NYC. Maximum 175 psi
(12,1 bar) by FM and LPCB.
Temperature Ratings
155F/68C Sprinkler - 135F/57C Plate
200F/93C Sprinkler - 165F/74C Plate
Discharge Coefficient
K = 5.6 GPM/ps1112 (80,6 LPM/barl'2)
Adjustment
1/2 inch (12,7 mm)
Finishes
Cover Plate: Chrome Plated, Brass
Plated, or White Painted (Custom
paint matches and colors other than
white are available on request.) 1
Pagel of 4 JANUARY, 2008 TFPI8I
Page 2 of 4 TFPI8I
1/2' NPT SEALING
ASSEMBLY
FRAME
CAP
SUPPORT
CUP WITH __.__- BULB
ROLL FORMED
THREADS
-
- - - COMPRESSION
SCREW
GUIDE -
PINS (2)
DEFLECTOR
-j---=-..
DEFLECTOR POSITION)
SPRINKLER/SUPPORT CUP
ASSEMBLY
THREAD INTO RETAINER
SUPPORT CUP 0 WITH THREAD
UNTIL MOUNTING DIMPLES
SURFACE IS
FLUSH WITH EJECTION
CEILING SPRING
SOLDER
I L
COVER
TABS (3) COVER PLATE/RETAINER PLATE
ASSEMBLY
FIGURE 1
SERIES RFII CONCEALED SPRINKLER
ASSEMBLY
Physical Characteristics
Frame .............Bronze
Support Cup . Chrome Plated Steel
Guide Pins ......Stainless Steel
Deflector ...........Bronze
Compression Screw ......Brass
Bulb ...............Glass
Cap ........Bronze or Copper
Sealing Assembly ..........
Beryllium Nickel w/Teflon*
Cover Plate ...........Brass
Retainer ............Brass
Ejection Spring . . . . Stainless Steel
Patents
U.S.A. 4,014,388
Operation
When exposed to heat from a fire, the
Cover Plate, which is normally sol-
dered to the Retainer at three points,
falls away to expose the Sprinkler As-
sembly. At this point the Deflector sup-
ported by the Guide Pins drops down
to its operational position.
The glass Bulb contains a fluid that
expands when exposed to heat. When
the rated temperature is reached, the
fluid expands sufficiently to shatter the
glass Bulb, activating the sprinkler and
allowing water to flow.
Design
Criteria
The RFII (TY3551), 5 mm Bulb Type,
Concealed Pendent Sprinklers are UL
and C-UL Listed as standard response
- standard spray sprinklers for use in
accordance with the current NFPA
standard. They are FM Approved as
standard response - standard spray
sprinklers for use in accordance with
the current FM Loss Prevention Data
Sheets.
The RFII (TY3531) 3 mm Bulb Type,
Concealed Pendent Sprinklers are UL
and C-UL Listed as quick response -
standard spray sprinklers for use in
accordance with the current NFPA
standard. They are FM Approved as
standard response - standard spray
sprinklers for use in accordance with
the current FM Loss Prevention Data
Sheets.
The Series RFII Concealed Pendent
Sprinklers are only listed and ap-
proved with the Series RFII Concealed
Cover Plates having a metallic or white
painted finish.
The Series RFII must not be used in
applications where the air pressure
above the ceiling is greater than that
below. Down drafts through the Sup-
port Cup could delay sprinkler opera-
tion in a fire situation.
Installation
The Series RFII must be installed in
accordance with the following instruc-
tions:
NOTES
Do not install any bulb type sprinkler if
the bulb is cracked or there is a loss of
liquid from the bulb. With the sprinkler
held horizontally, a small air bubble
should be present. The diameter of the
air bubble is approximately 1/16 inch
(1,6 mm) for the 155°F/68°C and 3/32
inch (2,4 mm) for the 200°F/93C tem-
perature ratings.
A 1/2 inch NPT sprinkler joint should
be obtained with a minimum to maxi-
mum torque of 7 to 14 ft.lbs. (9,5 to
19,0 Nm). Higher levels of torque may
distort the sprinkler inlet with conse-
quent leakage or impairment of the
sprinkler.
Do not attempt to compensate for in-
sufficient adjustment in the Sprinkler
Assembly by under- or over-tightening
the Sprinkler/Support Cup Assembly.
Readjust the position of the sprinkler
fitting to suit.
Step 1. The sprinkler must only be
installed in the pendent position and
with the centerline of the sprinkler per-
pendicular to the mounting surface.
Step 2. Remove the Protective Cap.
Step 3. With pipe thread sealant ap-
plied to the pipe threads, hand tighten
the sprinkler into the sprinkler fitting.
Step 4. Wrench tighten the sprinkler
using only the RFII Sprinkler Wrench
(Ref. Figure 3). The RFII Sprinkler
Wrench is to be applied to the Sprin-
kler as shown in Figure 3.
Step 5. Replace the Protective Cap
(Ref. Figure 4) by pushing it upwards
until it bottoms out against the Support
Cup. The Protective Cap helps prevent
damage to the Deflector and Arms dur-
ing ceiling installation and/or during
application of the finish coating of the
ceiling. It may also be used to locate
the center of the clearance hole by
gently pushing the ceiling material up
against the center point of the Protec-
tive Cap.
NOTE
As long as the Protective Cap remains
in place, the system is considered to
be "Out of Service".1 A
* Registered Trademark of DuPont
Step 6. After the ceiling has been com-
pleted with the 2-1/2 inch (63,5 mm)
diameter clearance hole and in prepa-
ration for installing the Cover Plate As-
sembly, remove and discard the Pro-
tective Cap, and verify that the
Deflector moves up and down freely. If
the Sprinkler has been damaged and
the Deflector does not move up and
down freely, replace the entire Sprin-
kler assembly. Do not attempt to mod-
ify or repair a damaged sprinkler.
Step 7. When installing an Air and
Dust Seal, refer to Figure 5, otherwise
proceed to Step 8. To attach the Air
and Dust Seal, verify the angle of the
outside edge of the seal is oriented
according to Figure 5. Start the edge
of the Retainer in the grooved slot of
the Air and Dust Seal and continue
around the retainer until the entire Air
and Dust Seal is engaged.
NOTE
The Air and Dust Seal is only to be
installed on the periphery of the Re-
tainer.
Step 8. Screw on the Cover Plate/Re-
tainer Assembly until the Retainer -
Figure 2 (or Air and Dust Seal - Figure
5) contacts with the ceiling. Do not
continue to screw on the Cover
Plate/Retainer Assembly such that it
lifts a ceiling panel out of its normal
position. If the Cover Plate/Retainer
Assembly cannot be engaged with the
Support Cup or the Cover Plate/Re-
tainer Assembly cannot be engaged
sufficiently to contact the ceiling, the
Sprinkler Fitting must be repositioned.
Care and
Maintenance
The Series RFll must be maintained
and serviced in accordance with the
following instructions:
NOTES
Absence of the Cover Plate Assembly
may delay sprinkler operation in a fire
situation.
TFPI8I Page 3 of 4
FACE OF CLEARANCE HOLE
SPRINKLER DIAMETER
FITTING DIMENSION C
SPRINKLER
SUPPORT CUP
ASSEMBLY 'Z
1/2" (12.7 mm)
THREADED
D ADJUSTMENT
FACE OF CEILING,
RETAINING RING
MOUNTING
SURFACE
5 . .
I II
3/16" to 11/16' MANUFACTURER DEFLECTOR COVER PLATE
(4,8 to 17,5 mm) PRESET GAP IN DROPPED RETAINER
REFERENCE 3/32' (2,4 mm) POSITION ASSEMBLY
COVER PLATE COVER PLATE
- PROFILE DEPTH DIAMETER
DIMENSION B DIMENSION A
3-1/4"(82,6 mm) C: 2-3/8" to 2-5/8" (60,3 to 66,7 mm)
3/16' (4,8 mm) D: 1-3/4' to 2-1/4" (44,5 to 57,2 mm)
FIGURE 2
SERIES RFII CONCEALED SPRINKLER
INSTALLATION DIMENSIONS
Page 4 of 4 TFPI8I
When properly installed, there is a
nominal 3/32 inch (2.4 mm) air gap
between the lip of the Cover Plate and
the ceiling, as shown in Figure 2. This
air gap is necessary for proper opera-
tion of the sprinkler. If the ceiling is to
be repainted after the installation of
the Sprinkler, care must be exercised
to ensure that the new paint does NOT
seal off any of the air gap.
Factory painted Cover Plates MUST
NOT be repainted. They should be re-
placed, if necessary, by factory
painted units.
Do not pull the Cover Plate relative to
the Enclosure. Separation may result.
Before closing a fire protection system
main control valve for maintenance
work on the fire protection system that
it controls, permission to shutdown the
affected fire protection system must be
obtained from the proper authorities
and all personnel who may be affected
by this action must be notified.
Sprinklers that are found to be leaking
or exhibiting visible signs of corrosion
must be replaced.
Automatic sprinklers must never be
painted, plated, coated or otherwise
altered after leaving the factory. Modi-
fied sprinklers must be replaced.
Sprinklers that have been exposed to
corrosive products of combustion, but
have not operated, should be replaced
if they cannot be completely cleaned
by wiping the sprinkler with a cloth or
by brushing it with a soft bristle brush.
Care must be exercised to avoid dam-
age to the sprinklers - before, during,
and after installation. Sprinklers dam-
aged by dropping, striking, wrench
twist/slippage, or the like, must be re-
placed. Also, replace any sprinkler that
has a cracked bulb or that has lost
liquid from its bulb. (Ref. Installation
Section).
If a sprinkler must be removed, do not
reinstall it or a replacement without
reinstalling the Cover Plate Assembly.
If a Cover Plate Assembly becomes
dislodged during service, replace it im-
mediately.
The owner is responsible for the in-
spection, testing, and maintenance of
their fire protection system and de-
vices in compliance with this docu-
ment, as well as with the applicable
standards of the National Fire Protec-
tion Association (e.g., NFPA 25), in
addition to the standards of any other
authorities having jurisdiction. The in-
stalling contractor or sprinkler manu-
facturer should be contacted relative
to any questions.
Automatic sprinkler systems should be
inspected, tested, and maintained by a
qualified Inspection Service in accord-
ance with local requirements and/or
national codes.
Limited
Warranty
Products manufactured by Tyco Fire &
Building Products (TFBP) are war-
ranted solely to the original Buyer for
ten (10) years against defects in mate-
rial and workmanship when paid for
and properly installed and maintained
under normal use and service. This
warranty will expire ten (10) years
from date of shipment by TFBP. No
warranty is given for products or com-
ponents manufactured by companies
not affiliated by ownership with TFBP
or for products and components which
have been subject to misuse, improper
installation, corrosion, or which have
not been installed, maintained, modi-
fied or repaired in accordance with ap-
plicable Standards of the National Fire
Protection Association, and/or the
standards of any other Authorities
Having Jurisdiction. Materials found
by TFBP to be defective shall be either
repaired or replaced, at TFBP's sole
option. TFBP neither assumes, nor
authorizes any person to assume for it,
any other obligation in connection with
the sale of products or parts of prod-
ucts. TFBP shall not be responsible for
sprinkler system design errors or inac-
curate or incomplete information sup-
plied by Buyer or Buyer's repre-
sentatives.
In no event shall TFBP be liable, in
contract, tort, strict liability or under
any other legal theory, for incidental,
indirect, special or consequential dam-
ages, including but not limited to labor
charges, regardless of whether TFBP
was informed about the possibility of
such damages, and in no event shall
TFBP's liability exceed an amount
equal to the sales price.
The foregoing warranty is made in lieu
of any and all other warranties. ex-
press or implied, including warranties
of merchantability and fitness for a
particular purpose.
This limited warranty sets forth the ex-
clusive remedy for claims based on
failure of or defect in products, materi-
als or components, whether the claim
is made in contract, tort, strict liability
or any other legal theory.
This warranty will apply to the full ex-
tent permitted by law. The invalidity, in
whole or part, of any portion of this
warranty will not affect the remainder
Ordering
Procedure
When placing an order, indicate the
full product name. Contact your local
distributor for availability.
Sprinkler Assembly:
Specify: (SIN), (specify temperature
rating) Series RFII Concealed Pen-
dent Sprinkler, P/N (specify).
ISSFISRC 200F193C
lTv3551 51--790-1-1553 51-790-1-200
TY3531 51-792-1-155 51-792-1-200
Separately Ordered Cover Plate:
Specify: (specify temperature rating)
Series RFII Concealed Cover Plate
with (specify finish), P/N (specify).
135F/57C(a) 165F/74C(b)
Brass 56-792-1-135 56-792-1-165
Bright Brass 56-792-2-135 56-792-2-165
Chrome 56-792-9-135 56-792-9-165
Brushed Chrome 56-792-8-135 56-792-8-165
White 56-792-0-135 56-792-0-165
White (RAL9010t 56-792-3-135 56-792-3-165
lBriaht White 56-792-4-135 156-7924-165
Off White 56-792-5-135 56-792-5-165
Black 56-792-6-135 56-792-6-165
Custom 56-792-X-135 56-792-X-165
For use with 15517/68C sprinklers.
For use with 200F/93C sprinklers.
Eastern Hemisphere sales only.
Sprinkler Wrench:
Specify: RFII Sprinkler Wrench,
P/N 56-000-1-075.
Air and Dust Seal:
Specify: Air and Dust Seal, 1 6 P/N 56-908-1-001.
0 2008 TYCO FIRE & BUILDING PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446
300
RING HANGER
<9> C®US I thru 4 inch pipe 112 and 314 Inch pipe
5 thru 8 Inch pipe
SIZE - 1/2 thru 8 inch pipe.
MATERIAL - Carbon Steel, Mil. Galvanized to G-90 specification.
FINISH - Mu. Galvanized and Stainless Steel.
LISTING - UL in US and CANADA.
APPROVAL - Factory Mutual Research.
CONFORMS WITH: Federal Specification WW-H- 17 1 (Type 10),
Manufacturers Standardization Society ANSI/MSS-SP-58 (Type 10); install
in accordance with ANSI/MSS- SP-69.
MAXIMUM TEMPERATURE - 650°F.
FUNCTION - For fire sprinkler and general piping purposes.
Swivel nut permits hanger adjustment after installation.
FEATURES.
I thru4 inch:
* Offset edge for EASY pipe insertion.
1 thru 8 inch:
* Full length knurl on swivel nut for better grip.
UNIQUE FEATURES
1 thru 3 inch:
* UL listed to accept AFCON#3 10 Surge Restrainer.
* Swivel nut
Retained in ring to keep the assembly intact prior to installation.
Removed easily if needed.
* UL listed for use on CPVC pipe.
ORDERING - Part # and pipe size.
Index
['MIJI
IMPERIAL MAX REC.
LOAD LBS.
METRIC
PIPE ROD PIPE ROD
1/2 318 400 10
3/4 3/8 400 20 10
3/8 400 s 10
11/4 318 400 32 10 1
11/2 3/8 400 40 to
3/8 400 50 10
2112 600 65 10
3 3/8 600 80 10
31/2 318 600
- io
4 318 1000 100 _..JL
5 112 1250 125 12
6 1/2 1250 150 12
L 112 1250 12
Order Part #300m
Note: 1/2' Ring Hanger not <FM> approved
( D
#611
r bottom cord as shown
structural and dimensional ii1.y of joist.
in cord space.
OPEN WEE BAR JOIST
# 61
611
CEILING PLATE
SIZE - 3/8"Rod
MATERIAL - Carbon Steel.
FINISH - Plain, Electro-Galv. and Stainless Steel.
LISTING - UL in US and CANADA.
FUNCTION -Attachment to metal beams, decks and
walls or wood beams, ceilings and walls. May also be
welded.
INSTALLATION - To support 1/2" thru 4" pipe.
Install per NFPA - 13 with additional UL listed
fasteners, per chart below. UL listed to support 4" pipe
when welded or installed in Bar Joist.- See Drawing
FEATURES
* Offset allows 3/16" thread thru zone.
* Radius - Tapped orifice: Aligns rod for easy thread
engagement and eliminates structural deficiencies
associated with press-in tapped inserts such as:
Loose fit - Due to material tolerance variation.
Deformation - Bore egging caused by improper
Insertion.
Misalignment - Caused by improper insertion.
ORDERING - Part # and finish.
UL LISTED FASTENERS TESTED PER NFPA -13
WOOD
No Pre Drill Using 1/4"
STEEL
or #14 Tek Type Screw
Fastener
Type
Qty.
Fastener
Max Pipe
Size
Minimum
Thickness
Qty.
Fasteners
Max Pipe
Size
l/4x2Lag Bolt 2 3 1 14 GA. 2 2
#14 x 11/4" Wood Screw 2 2 16GA. 2 2
Index
10/00
655
ALL THREADED ROD CUT TO LENGTH
ROD
SIZE
MAX. REC.
FOR SERVICE
LOAD LBS.
TEMP.
650°F 750°F
3/8 610 540
1/2 1130 1010
5/8 1810 1610
3/4 2710 2420
7/8 3770 3360
NOTE; maximum Temperature: 750°F
SIZE - 3/8 thru 7/8 inch rod in 1 inch
increments.
MATERIAL - Carbon Steel.
FINISH - Plain, .Electro-Galvanized and
Stainless Steel.
ORDERING - Part #, rod diameter, rod
length and finish.
2/00 8
MW Deck
125 (Prefow)
Metal Deer
It 125 Puitin
Product Features
The Sammy X.Press expands to provide Installs in seconds, saving time &
direct vertical attachment in: Installations costs.
- Metal Deck (22-16 gauge)
- Z-Pudin (18-16 gauge) Use in applications where access
to the back of the installed fastener is
The Sammy K-Press Swivelaltows you prohibited. (is. metal roof deck, tubular
to hang plumb in extreme root pitches: steel, or vapor banter fabric.)
- 89° in Z-Purtin
45° in metal deck for 12/12 pitch Less jobsite material needed.
The SammyX.Press Sidewinder expands No retaining nut required.
to provide horizontal attachment in:
-16 go -3/16' steel - purlin, tubular Provides design flexibitily.
steel.
U
II
Patent 140
6.935,821
1 VOR
PontPending Roof RMSARMI
P) L')
JERTICAL MOUNT
114' 8181922 XP 200 X-Press 200 1148 (22 gal 19alfunwiducl NA .125' 25 125 Metal Deck
650 (2W Pipe 983(2•p) 027.
. ¶ 1185 (Lurninalm) 318' 8150922 XP 20 X41ress20 1146 (22 ga) 250 (Luratnalre) 1475 (4" Pipe) .027. AN 25 125 Metal Deck
283 (Condult& Cable)
12O(OWP) .000'
. 315' 8153922 XP 35 X.Pmss 35 1783 (1698) 250 (Lurninalm) 1475 (4- Pipe): .125' 25 125 Pudin
416 (Conduit& Cable) .056'
750 (2' PIpe)
170 vertical (Lumlnafre)
315' 8294922 SXP2O SwIvel X-Press20 1061 (22 8O@45' (Lummnahe) 635 (2- Pipe) .027' .125' 25 125 Metal Deck
283 vertical (ConduitS Cable)
233045' (Colrdidt&Cable)
1250(3W Pipe)
4.<> 1675 (16 250 vertical (Luminaire)
3)8' 8295922 SXP3S Swivel X-Piess35 80090°(Lrmilnaire) 635 (2' Pipe) .125' .OW 25 125 Pert/n 1558 (W offverdew) 500 vertical (Conduit & Cable)
333085' (Conduit & Cable) r PrePaurStiuctural Concrete 3000 psi
.. . 318' 8150922 XP2O SanimyX-Prass20 1148(22ga) 65012% pip) 25
L postPourRange lI WON 3sPCcOW"
wtcirLesirs.ec.itw.
1250 (3W Pipe)
tIc' 315' 8293957 SWXP35 SldewinderX-Press35 1798(16ga) 80 (Luminahe) .060' .125' 25
416 (ConduIt & Cable)
Pro.Pow Structural concrete @ 3000 psi PosbPour Range 0 LWQ5 35PCF (thai W)
UXPIT
Patent Pending
I ii@ 9$1to b(]
8194910 UXPIP Universal X.PressllTool Il
8195910 WIT Relio Socket for 8151910 1
8152910 XPDB 26W Dull Bit
'Tool Incindes Sleeve, Bit Receiver, Max Vàenth, and 25164' 00 IN.
_ 4
To welch a video demonstration of fire Sammy X-P,ess. visit hltp:/Anwwsamniysuperscre
0
(en.
MAO5INU.A
20