Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
1250 CARLSBAD VILLAGE DR; ; FA090019; Permit
11/3/2020 . FA090019 Permit Data City of Carlsbad Fire Alarm Permit . Permit No: FA090019 1250 CARLSBAD Job Address: . . Status: ISSUED VILLAGE DR Permit Type: FALARM . Applied 4/21/2009 Parcel No: . • • Approved: 4/21/2009. Lot #: 0 . • Reference No.: . Issued: 4/21/2009 PC #: . • Inspector: Project Title: COLE LIBRARY FIRE ALARM PLAN CHECK & INSPECTION Applicant: Owner: SIMPLEX GRINNELL 3568 RUFFIN ROAD SAN DIEGO CA 858-633-9100 Fees ($) Add'l Fees ($) Total ($) Balance ($) .0 . •.0 . 0 0 1/1 . - tqco /Fire & I S implex6rinneff Security 4.- SimplexGrinnell LP 9855 Carroll Canyon Road San Diego, CA 92131 Tele: (858) 740-0100 Fax: (858) 740-0156 www.simplexgrinnell.com FIRE ALARM PRODUCT SUBMITTAL PROJECT: Carlsbad Library 1250 Carlsbad Village Drive Carlsbad, CA 92008 ip, C Ø 4/14/2009 REV.#: 0 PROJECT #: FA01cot c SimplexGrinnell LP 9855 Carroll Canyon Road tyco l Fre/ & / SimplexGrinne II San Diego, CA 92131 Tele: (858) 740-0100 Security 0 Fax: (858) 740-0156 www.simplexgrinnell.com TAB# SYSTEM I FIRE ALARM 2 APPENDIX S 4/14/2009 REV.#: 0 PROJECT #: tqco / Fire & / SimplexGrinnell Security SirnplexGrinnell LP 9855 Carroll Canyon Road San Diego, CA 92131 Tele: (858) 740-0100 Fax: (858) 740-0156 www.simplexgrinnell.com -, ITEM MODEL NO. DESCRIPTION C.S.F.M. NO A 4010-9101 4010 FACP 7170-0026:226 B 2081-9288 12.7 Amp/Hour Batteries N/A C 4099-9001 Addressable Pull Station 7150-0026:224 0 4098-9792 Addressable Detector Base 7300-0026:217 4098-9714 Photo Detector. 7272-0026:218 4098-9756 Duct Detector Housing 3240-0026:241 2098-9797 Sampling Tube N/A F 4906-9103 Strobe Only, Multi-cd, Wall Mount 7125-0026:316 -, 4906-9104 Strobe Only, Multi-cd, Ceiling Mount 7125-0026:316 G 4906-9129 Horn/Strobe, Multi-cd, Wall Mount 7125-0026:317 4906-9130 Horn/Strobe, Multi-cd, Ceiling Mount 7125-0026:317 S S 4/14/2009 REV.#: 0 PROJECT #: . Simplex TrueAlarm® Fire Alarm Controls UL, ULC Listed; FM, CSFM, Model 4010 Fire Alarm Control Panel for TrueAlarm and MEA (NYC) Approved* Analog Sensors and lDNetTM Addressable Devices C I1iuit* Standard features include: Up to 250 addressable TrueAlarm sensor or addressable device points using IDNet communications that operate with either shielded or unshielded twisted pair wiring** Four, 2 A notification appliance circuits (NACs) with solid state current protection Internal event reporting DACT module (standard on models 4010-9101, 4010-9102, & 4010-9150) UL listed to Standard 864 Installation convenience features: Power-limited design with electronic modules contained on one-piece chassis Up-front terminal blocks for wiring access Compact NEMA 1 rated cabinet is available in beige or red and can be pre-shipped for early installation Setup, programming, and maintenance features: Device level ground fault search, locate and isolate Auto Prograin for general alarm operation TrueAlarm individual analog sensing with front panel information and selection access "Dirty" TrueAlarm sensor maintenance alerts, service and status reports including "almost dirty" Default TrueAlarm sensor device type operation Duplicate address error detection Front panel or PC programming TrueAlarm sensor peak value performance report WALKTEST'' silent or audible system testt Software verification simulation mode Supports the following IDNet devices: Addressable manual stations Quad-state zone adapter modules (ZAMs) for initiating device monitoring IDNet ground fault/short circuit isolator base for TrueAlarm sensors Quad-state line powered individual addressable modules (lAMs) for initiating device monitoring and relay control Available option modules include: Door mounted 24 LED annunciator (std. on ULC models) Network, or Point Reporting DACT Class A NAC adapter module RS-232 ports for printer and maintenance PC Additional power supply; Auxiliary Relay Module or City Interface Equipment for Suppression Release Applications (refer to data sheet S4010-0003) Compatible with Simplex® auxiliary panels: TrueAlert® Addressable Controllers and NAC power extenders (IDNet controlled and conventional) 4003 Voice Control Panel 4081 Battery Cabinet with charger for 50 Ah batteries 4010 Fire Alarm Control Panel (with standard door) )cscrintir TrueAlarm fire alarm control panels have the ability to provide location accuracy for monitoring and control. When equipped with TrueAlarm analog sensing for smoke and heat detection, the processing power of the control panel also has the ability to analyze conditions at each location to provide accurate detection with significantly reduced maintenance costs. The 4010 TrueAlarm Fire Alarm Control Panel has been specifically designed to provide addressable operation and analog detection in a cost-effective package for application sizes that previously were considered only appropriate for conventional zoned monitoring. Installation and Service Ease. The 4010 mounts on a single chassis for quick installation and removal. Terminal blocks are large and up-front for easy access and inspection. Optional modules are easily and quickly installed and programmed as required. The 4010 cabinet provides convenient stud markers for drywall thickness and nail-hole knockouts for quicker mounting. Smooth cabinet surfaces are provided for locally cutting conduit entrance holes exactly where required. 4010 cabinets and electronics can be ordered separately, allowing early cabinet installation. Ground Fault Assistance. Ground fault problems often occur during installation. The 4010 provides isolating circuitry and software-controlled sequencing to isolate ground faults to specific identified locations. This assistance helps the installer to accurately locate the wiring problem for quicker repair. Refer to page 6 for listing details. This product has been approved by the California Stale Fire Marshal (CSFM) pursuant to Section 13144.1 of the California Health and Safety Code. See CSFM Listing 7170.0026:226 for allowable values and/or conditions concerning material presented in this document. Ills subject to re-examination, revision, and possible cancellation. Accepted for use - City of New York Department of Buildings - MEA35-93E. Additional listings may be applicable: contact your local Simplex product supplier for the latest status. Listings and approvals under Simplex Time Recorder Co. are the property of Tyco Safely Products Westminster. "lrueAlarm analog smoke detection and IDNet addressable devices are protected by one or more of the following U.S. Patents: 5,155,468; 5,173,683; 5,543,777; 5,400,014; 5,552,765; 5,552,763; DES. 377.460. t WALKTEST system test is protected under U.S. patent #4,725,818. S4010-0001-9 10/2004 j EE 1 -F vwri o 0 : SYSTEM RESET restores control panel to normal when all alarmed inputs are returned to normal 0 0 S Extensive Feature List. The 4010 Fire Alarm Control Panel provides access to an extensive feature list that includes: . Providing easy and powerful operator infonnation with a logical, menu-driven display Extensive and automatic diagnostics for maintenance iiduction .. History Logs available from the LCD or capable of (optionally) being printed Software Verification,allowing detailed logic programming simulation to be conducted without activating connected outputs Control Panel (or service PC) label editing Password access control Auto Program Quick Configuration (Quick-CFIG) of connected modules and IDNet devices for general alarm operation to quickly get the system up and running Convenient Status Information. With the locking door closed, a window allows viewing of the status display. The 4010 status panel provides a two line by 40 character, super-twist LCD information display and eight status LED indicators as shown in the illustration below. From this display, the LED indicators will describe the general category of activity being displayed with the LCD providing more detail. For the authorized user, unlocking the door will provide access to the control switches and allow further inquiry by scrolling the display for additional detail. (Refer to control panel functional illustration below.) WALKTEST Diagnostic Operation Mode. The patented WALKTEST process allows a single person to perform system test. The system records test inputs such as intentional alarms or trouble and either logs the response (silent WALKTEST operation) or outputs a brief, recognizable audible notification signal (audible WALKTEST operation). Extended Operator Control Panel Functions M - FIVE STATUS INDICATOR LEDs provide system status indications in addition to LCD information, LEDs flash to indicate the condition and then when acknowledged, remain on until reset THREE PROGRAMMABLE LEDs Provide custom labeling (labels insert into 2 X 40 LCD READOUT, LED backlighted during normal conditions and abnormal operating conditions, provides up to 40 characters for custom label information a pocket), the top two LEDs are [ FIRST ALARM DISPLAY: Operation can be selected for maintained display of first 1 selectable as red or yellow, the bottom alarm until acknowledoed LED is selectable as green or yellow SO I SYSTEM IS NORMAL 12:02: 15'rn Mon 18-Oct-04 ALARM ACK acknowledges a Fire Alarm condition, logs the acknowledge and silences the operator panel and all annunciator tone-alerts SUPV ACK acknowledges system supervisory conditions, logs the acknowledge, and silences the operator panel and all annunciator tone-alerts \ 1NINE EXTENDED FUNCTION KEYS (accessible with \ door open) select and scroll through display prompts for \ I locating additional system information, performing \ 1maintenancefunctions, or for front panel programming ALARM SILENCE causes audible notification appliances to be silenced, used after evacuation is complete and while alarm source is being investigated TROUBLE ACK acknowledges system troubles, logs the acknowledge, and silences the operator panel and all annunciator tone-alerts S S4010-0001-9 10/2004 IITTT I= 080171 M. TrueAlarm heat sensors can be selected for rate-of-rise detection as either 150 F (8.3° C) or 20° F (II . I° C) per minute with an independent fixed limit of 1350 F (570 C) or 155° F (68° Q. TrueAlarm heat sensors can also be programmed as a utility device to monitor for temperature extremes in the range from 32° F to 155° F (0° C to 68° Q. This feature can provide freeze warnings or alert to HVAC system problems. To additional IDNet devices, up to 250 total I Modular TrueAlarm TrueAlert Addressable controller I sensor with base Supervised lAM Modular TrueAlarm sensor I with IDNet isolator base Addressable station 4009 IDNet NAC Extender Quick-Connect Monitor ZAMs and TrueAlarm se I Relay lAMs 4010 Fire Alarm I Control Panel with I annunciator door I'll 4010 Control Panel with Typical IDNet Devices !Ilt.111['.1,DI PITI1il I1'A[.(I'j TrueAlarm operation gives the 4010 system the ability to automatically indicate when a sensor is almost dirty, dirty, and excessively dirty. The NFPA 72 (National Fire Alann Code) requirement for a test of the sensitivity range of the sensors is fulfilled by the TrueAlarm ability to maintain the sensitivity level of each sensor. Modular TrueAlarm sensors use the same base and different sensor types (photoelectric smoke sensor, or heat sensor) can be easily interchanged to meet specific location requirements. This feature also allows intentional sensor substitution during building construction. When conditions are temporarily dusty, instead of covering the smoke sensors (causing them to be disabled), heat sensors may be installed without reprogramming the control panel. Although the control panel will indicate an incorrect sensor type, the heat sensor will operate at a default sensitivity to provide heat detection for building protection at that location. [] IIP] ENTER it**i1MT-MM Overview. The 4010 provides I DNet addressable device communications. Using a two wire circuit, individual devices such as manual fire alarm stations, TrueAlarm sensors, and sprinkler waterfiow switches can be directly connected (or interfaced) to the IDNet controller to communicate their identity and status. This addressability allows the location and condition of the connected device to be displayed on the 4010 panel LCD and on system annunciators. Additionally, control circuits (fans, dampers, etc.) may be individually controlled by using a - 'relay lAM (individual addressable module). The 4009 IDNet NAC Extender or the TrueAlert Addressable controller can be controlled for local or remote notification appliance expansion. (Refer to individual device documentation for further details.) Capacity. A total of 250 addressable monitor and control points may be intermixed on the same pair of wires. By using Zone Adaptor Modules (ZAMs) or Individual Addressable Modules (lAMs), conventional initiating devices can be connected to the IDNet circuit. IDNet Addressable Operation. The IDNet controller continuously interrogates each addressable device on the communication channel for status condition such as: normal, off-normal, alarm, supervisory, or trouble. Sophisticated poll and response communication techniques ensure supervision integrity and allow for "T-tapping" of the circuit for Class B (Style 4) operation. Wiring Requirements. Refer to the specifications chart below. Ditances are for shielded or unshielded wire. Shielded wire may provide protection from unexpected sources of interference and may be required for some applications. Wiring Specifications Size 18 AWG minimum Wire Preferred Shielded twisted pair (SIP) Unshielded twisted pair (UT?) Acceptable Farthest Distance from Control Up to 2500 feet (762 m) Panel to Device Total Wire Length Allowed With Up to 10,000 ft (3 km). T laps for Class B_Wing lIT TrueAlarm System Operation. IDNet communications are used for TrueAlarm smoke and temperature sensors. Every four seconds, smoke sensors transmit an output value based on their smoke chamber condition. The 4010 CPU maintains a current value, peak value, and an average value of each sensor's output. Status is determined by comparing the current sensor value to its average value. Tracking this average value as a continuously shifting reference point filters out environmental factors that cause shifts in sensitivity. Programmable Sensitivity. The sensitivity of each sensor can be field programmed at the 4010 Control Panel for different levels of smoke obscuration (in percent) or for specific heat detection levels. In order to evaluate whether the sensitivity should be revised, the peak value is stored in memory and can be easily read and compared to the alarm threshold directly in percent. S4010-0001-9 10/2004 TrueAlarm Information Details True Alarm sensor data can be displayed on the system LCD, on a remote maintenance PC, or printed on a remote printer. With the proper operator access, a TrueAlarm Service Report can be generated to list the specific details of each lrueAlanzi device. This report, as well as the Status Report can either be displayed on the remote maintenance PC or captured permanently by using a remote 80 character printer. The report samples below illustrate the format provided on either the remote maintenance PC or a printer. This information is available at the system LCD by identifying the specific point of interest and reading one point at a time. Model 4190-9013 is a UL Standard 864 listed 80 column, 24 pin dot matrix printer (refer to data sheet S4190-001 1). (Model 2190-9039, a 24 VDC, 40 column printer, is compatible with the 4010 for event printing only. Refer to data sheet S2190-0014.) (SimplexPrinter model 5 Local I maintenance corn :1 _ 4010 Fire Alarm ' Qg connection type per 4010, Control Panel " selected by module choice; max. '-..i wiring distance is 300 ft (91 in) © 9600 baud , Remote authorized maintenance computer connected via dial-up Service Modem Connection RS-232 Connection Options (refer to module selection on page 6) TrueAlarm Status and Service Report Samples Simplex 4010 Fire Alarm System Page 1 REPORT 3 : TrueAlarm Status Report 2:43:03 pm Mon 18-Oct-04 Zone Sensi- Almost Name Custom Label tivity Device Status Dirty Mi-i ANALOG PHOTO CLEAN ROOM 0.5 t NORMAL M1-2 ANALOG ION CLEAN ROOM 1.3 fj NORMAL M1-3 ANALOG PHOTO MAIN LOBBY 2.5 t NORMAL *YES* Ml-4 ANALOG PHOTO CONFERENCE ROOM 1 2.5 Pi NORMAL Ml-10 HEAT DETECTOR GARAGE 135 F NORMAL MI-11 ANALOG PHOTO KITCHEN 3.7 NORMAL *YES* END OF REPORT Typical TrueAlarm Status Report Information Printout and/or Maintenance PC Screen Simplex 4010 Fire Alarm System Page 1 REPORT 4 : TrueAlarm Service Report 2:56:09 pm Mon 18-Oct-04 Dev Alarm Avg Current! Peak! State Num Custom Label at: val alarm alarm 1 ANALOG PHOTO - CLEAN ROOM 0.5/ 83 67 68/ i 72! 10 NOR 2 ANALOG ION - CLEAN ROOM 1.3!209 94 97/ 2t 101! it NOR 3 ANALOG PHOTO - MAIN LOBBY 2.5/185 117 117! O 125! 42 NOR 4 ANALOG PHOTO - CONFERENCE ROOM 1 2.5/161 93 93! 0 93! Ot NOR 10 HEAT DETECTOR - GARAGE 135F!253 --- 63!-67F 66! 69F NOR ii ANALOG PHOTO - KITCHEN 3.7/216 116 116! i°, 110/ 36% NOR END OF REPORT Typical TrueAlarm Service Report Information Printout and/or Maintenance PC Screen 4 S4010-0001-9 10/2004 S C IIT.IflTI liui*i N2 Communications for Serial Annunciator Control. Control for up to 6 remote Simplex Annunciator products including 24 Point I/O Module, and LCD Annunciator. Includes extensive troubleshooting diagnostics. Access Port. RS-232 service port for conflicting PC tools for service diagnostics and for programming the CPU Flash EPROM memory. IDNet Addressable Communications Channel. Addressable channel provides communications for up to 250 remote addressable devices, including TrueAlarm analog sensors and isolator bases (see descriptions on page 3). Four NACs. Class B output is standard, rated for 2 A 24 VDC nominal, with solid state current protection. Class A operation is optional with the addition of an adapter module. NAC operation can be selected for "on-until-Silence" or "on-until-Reset," and can be Temporal pattern, 20 or 120 bpni March Time pattern, or continuous. Each NAC is also individually selectable to control Simplex synchronized visible notification appliances and to control audible notification appliances using SmartSyncTM control, allowing separate audible and visible appliance operation using a common 2-wire circuit. (Class A, Style Z, SmartSync circuits require SmartSync Control Module 4905-9938, refer to data sheet S4903-00 10 for details.) Two Auxiliary Output Circuits. Operation is programmable for trouble, alarm, supervisory, or other fire response functions. Output is one Form "C" dry contact each, rated 2 A @ 24 VDC. An optional relay kit is available for switching up to 1/2 A at 120 VAC. Power Supply. Standard output is 4 A @ 28 VDC, filtered, non-regulated. Internal system power is provided separately, allowing the 4 A to be available for NAC and auxiliary power tap functions. Over-current protection is solid state and self-resetting. Auxiliary Power Tap. Provides up to 1/2 A of the standard power supply voltage, over-current protected. Battery Charger. Capable of charging up to 25 Ah sealed load-acid batteries (4010 cabinet mounted). A recharge time of 24 hours is typical with stable 120 VAC input. For applications requiring larger batteries, external charger/cabinet assemblies are available. A depleted battery cutout feature is programmable to advise and/or to reduce current when battery voltage is low. reTWIN.M. (The 4010 is available with a Simplex Network Interface. 4010 points can be declared "public.") Network Interface, Fixed Media. Available for wired applications. Network Interface, Modular Media. Available for wired connections or fiber optic. Require separate media modules. May be both wired, both fiber optic, or one of each. DACT, Point Reporting Module. Provides serial output information that can send location details to a remote receiving station. DACT, Event Reporting Module. For applications where simple event status information is required (Alarm, Trouble, Supervisory, and AC power failure). Dual RS-232 Module. Available for interfacing to a printer and a maintenance PC. Single RS-232 Module with Service Modem Connection. Provides one port dedicated for connection to a printer, and a second port dedicated for dial-in from a service computer, typically located off-site. With an off-site computer, programming changes and system diagnostics can be performed remotely, reducing service time for repair or reprogram. Security is maintained by password protection. rirmrnir017 r Standard 4 A Expansion Module provides two taps of 2 A each, 28 VDC, filtered, non-regulated, similar to the standard power supply capacity. Suppression Release Power Supply provides two taps of 2 A each, regulated at 24 VDC ± 10%. May also be used for other applications requiring regulated voltage. Use for suppression release requires a front panel mounted release appliqué that is provided with this power supply and also may be ordered separately. Battery Meter Module provides panel mounted ammeter and voltmeter for power supply monitoring. Dual Circuit Class A NAC Adapter Module mounts on the main 4010 printed circuit assembly and provides the additional circuitry needed for Class A operation. Dual Circuit City Connect Module provides the interface required for direct wired reporting to conventional city connection circuits. (Available with or without disconnect switches.) Expansion Power Distribution Module provides two additional termination points for the 1/2 A auxiliary power output, or for one tap of the expansion power supply. Relay Option Module. Provides three relays, one each for Alarm, Supervisory, and Trouble. Relay contacts are selectable for normally open or normally closed and are rated 2 A @ 32 VDC maximum. Up to six of the following modules may be connected to the Simplex N2 serial communications bus. 4606-9101 LCD Annunciators provide remote acknowledge, reset, and alphanumeric status display. (Refer to data sheet S4606-0001.) 24 LED Annunciator Doors are standard on ULC listed models and are available as door-only assemblies for electronics only packages or other aftermarket applications. This option uses the 24 Point I/O module with all points pre-assembled as LED outputs, with individual labels and each LED is selectable as red or yellow. 4605 Series 24 Point I/O Modules are available for remote mounting and provide 24 points that can be programmed as either general purpose switch inputs or system controlled outputs. Typical applications are for remote annunciators and monitoring and control of other related processes. (Refer to data sheet S4010-0002.) S4010-0001-9 10/2004 S Category Control Panel Assembly (select one) Model 4010-9101 Description UL Listed 4010 Fire Alarm Control Panel with: door, cabinet, power supply/battery charger, IDNet interface, 4 NAGs, 2 auxiliary relays, and external N2 communications interface; 4010-9101 and 4010-9102 include internal common event reporting DACT Voltage 120 VAC Color Beige 4010-9102 Red 4010-9201 240 VAC Beige 4010-9202 Red 4010-9101C English French I ULC Listed 4010 Fire Alarm Control Panel; same as above I except: with 24 LED Annunciator door; and without DACT 120 VAC Beige 4010-9101 CF 4010-9150 UL Listed ULC I English I Listed French I 4010 Fire Alarm Control Panel electronics only, for pre-shipped cabinets, requires door and cabinet ordered separately; -9150 has event reporting DACT 120 VAC NA 4010-9150C 4010-9150CF OntinnI Pknansinn Sint Fturs (two slots arp availAhIpslt rnor1uls 2S rniiirc1 Category Model Description Reporting and Network Modules (select one) 4010-9810 4010-9816 DACT Module (Common Event Reporting) I Includes two, 7 ft (2.1 m) long RJ45 cables DACT Module (Point Reporting) I 4010-9821 Network Interface Module with fixed, wired connections 4010-9817 Network Interface Module, Modular; requires 2 (In/Out) media modules (see below) RS-232 4010-9811 Dual RS-232 Interface Module Communications 4010-9812 Single RS-232 Interface Module with Service Modem connection (select one) Media Modules 4010-9818 Network Wired Media Module I Media modules mount on the 4010-9817 module without impact to slot allocation space. 4010-9819 Network Fiber Optic Media Module Chassis Mounted Expansion Modules (select as required) Category Model Description Additional Power Supply (select one) 4010-9813 120 VAC input 4 A Expansion Power Supply 240 VAC input 4010-9823 4010-9814(CF) Suppression Release Power Supply; 4 A @24 VDC, regulated ± 10%; 120 VAC input 4010-9824 240 VAC input includes front panel suppression appliqué; CF suffix selects French Optional Features (select one) 4010-9820 4010-9825 Battery Meter Module (ammeter and voltmeter) 24 VDC Expansion Power Distribution Module, provides two additional termination points for an expansion power supply tap or the auxiliary power output 4010-9806 Dual Circuit Class A (Style Z) NAC Adapter Module, two maximum Optional Features (select as indicated) 4010-9809 Dual Circuit City Connect Module Dual Circuit City Connect Module w/o disconnect switches Relay Option Module Select one maximum 40109829* 4010-9803 Accessories Category Optional Features Model 4010-9826 Description - V 120 VAC Auxiliary Relay Kit, allows one auxiliary relay to control up to 1/2 A @120 VAC, select as required; 2 maximum 4010-9830 (CAF) Suppression Release Appliqué, required for suppression release applications; suffix CAF selects a French appliqué 2975-9801 Semi-flush trim, beige, 1-7/16" (37 mm) wide 2975-9802 Semi-flush trim, red, 1-7/16" (37 mm) wide Batteries (required if batteries are internal; select one size; two batteries are required) 2081-9272 6.2 Ah Battery, 12 VDC 2081-9274 10.0 Ah Battery, 12 VDC 2081-9288 12.7 Ah Battery, 12 VDC 2081-9275 18 Ah Battery, 12 VDC; NOTE: This battery size will not allow bottom entry conduit 2081-9287 25 Ah Battery, 12 VDC Cabinets (select one if pre-shipped) 2975-9215 Red Cabinet Dimensions: 22" H x 18" W x 5-3/8" D (559 mm x 457 mm x 137 mm) 2975-9214(CF) Beige Cabinet; CF suffix has French labels Doors (select one if pre-shipped or for use with 4010-9150) 4010-9858 Red Door with dress panel Dimensions: 22" H x 18" W x 5/8" 0 (559 mm x 457 mm x 16 mm) 4010-9857(CF) Beige Door with dress panel; CF has French labels 4010-9860 (CAF)* Beige Door with 24 LED Annunciator and dress panel; CAF suffix selects French for ULC applications Dimensions: 22" H x 18" W x 1-23/32"D (559 mm x 457 mm x 44 mm) [see also S4010-0002] 40109861* Red Door with 24 LED Annunciator and dress panel * As of document revision date: 4010-9829 is not ULC listed; 4010-9860 and 4010-9861 are listed by UL and ULC and approved by CSFM and FM; 4010-9860CAF is ULC listed and FM approved only. 6 S4010-0001-9 10/2004 S 4010 Operating Specifications 11 -- Input Power Requirements AC Input, 120 VAC base models Voltage Range 102 to 132 VAC Frequency 60 Hz Maximum Current 2 A AC Input, 240 VAC base models 204 to 264 VAC 50/60 Hz 1 A AC Input with 120 VAC expansion power supply 102 to 132 VAC 60 Hz 4 A AC Input with 240 VAC expansion power supply 204 to 264 VAC 50/60 Hz 2 A Environmental Operating Temperature 32° to 120°F (0° to 49° C) Operating Humidity Range Output Ratings Standard Power Supply Output Auxiliary Power Tap Expansion Power Supply Output * Suppression Release Power Supply Output . * Each power supply provides two output taps of 2 A each. 4 A total @ nominal 28 VDC 1/2 A maximum of standard power supply voltage Additional 4 A @ nominal 28 VDC Additional 4 A @ 24 VDC ±10% up to 93% RH, non-condensing © 100.4° F (38° C) maximum Output switches to battery backup during mains failure or brownout conditions Current Ratings for Optional Modules and Remote LCD Annunciator Model 4010-9810 Module DACT (Common Event Reporting) Supervisory Current 40 mA Alarm Current 40 mA 4010-9816 DACT (Point Reporting) 40 mA 40 mA 4010-9821 Network, wired communications - 125 mA 125 mA 4010-9817 Network Modular, add media cards separately 24 mA 24 mA 4010-9818 Network Wired Media 47 mA 47 mA 4010-9819 Network Fiber Optic Media 36 mA 36 mA 4010-9811 Dual RS-232 75 mA 75 mA 4010-9812 Single RS-232 with Service Modem 100 mA 100 mA 4010-9806 Dual Class A NAC Adapter 0 mA 0 mA 4010-9809 Dual Circuit City Connect 20 mA 36 mA 4010-9829 Dual Circuit City Connect w/o disconnect switches 20 mA 36 mA 4010-9803 Relay Option Module 10 mA 37 mA 4010-9860 4010-9861 & ULC 4010s 24 LED Annunciator door 60 mA 83 mA (all LEDs on) 4606-9101 Remote LCD Annunciator (refer to data sheet S4606-0001) 65 mA 140 mA System Current (supplied separate from power supply output) Base System with: no IDNet devices Supervisory Current** 195 mA Alarm Current** 295 mA 50 IDNet devices 230 mA 330 mA 100 IDNet devices 265 mA 365 mA 150 IDNet devices 300 mA 400 mA 200 IDNet devices 335 mA 435 mA 250 IDNet devices 370 mA 470 mA S ** Current Calculation Information: To determine total supervisory current, add currents of modules in panel to base system value and all auxiliary loads. To determine total alarm current, add currents of modules in panel to base system alarm current and add all panel NAC loads and all auxiliary loads. 7 S4010-0001-9 10/2004 LI S I II: 4010-9820 T83 TIM iiII• 4010-9809 Meter Module or -9829 or II:City Module 4010-9825 or 24VDCPower 4010-9803 Distribution II : Relay Module Block ----------- — -. Expansion Slots 1 & 2 TDI4444J I4Ml441 re I 0 00 4010-9806 4010-9806 Class : : Class Module :: Module 0 I 11 Mew 0 o o o o ocJ — 0 I., o : 0 0 ------------------- 4010-9813, 4098-9814 4010-9823. or 4010-9824 Expansion Power Supply -------------------- 0 -- 01 IQI / - - -. - - -' Typicai;nduit entry area (cut holes as required) 18"(457mm) Sri 21" FEW 33 mm) 8 _ 8 5 14-1/2" (368 mm)_Sr Battery Area No conduit entry or wiring in this area Shaded area is for non-power limited wiring / ___-1 Standard 1-19/32" w door profile (40 mm) 3/4' Annunciator (19 mm) -f'l door profile 7-3/32" i(180 mm) 1..— 6-1/4" (159 mm 5-1/2" h—(140 mm) Wall thickness guides for - 1/2" (13 mm)wall board Standard Door. - 46 5/8" (16 mm) thick l' thickness guides for 5/8" (16 mm) wall board) Annunciator Door. Internal straps are 1-23/32" (44 mm) thick provided for wiring i management (2 each s ide) Door and exposed cabinet dimension_ r for semi-flush mount - 2-15/32" (63 mm) i Knockout screw/nail holes Oe (for semi-flush mount) Wall board position reference for semi-flush mount (5 S 4010 Module Layout Reference Ir Mounting Information I - fl Tyco, Simpler, the Simplex logo, True-Alarm, IVALKTEST. 10Mm. SmariSync, and TrueAlert are trademarks of Tyco International AG or its afJiliaies in the U.S. and/or oilier countries. NFPA 72 and National Fire Alarm Code are registered trademarks oft/ic National Fire Protection Association (NFPA). eSlu1pIeJc Tyco Safety Products Westminster• Westminster, MA • 01441-0001 • USA S4010-0001-9 10/2004 www.tycosafetyproducts-usa-wm.com 020(J4 Tyco So/ely Products H'esunins:e, Al/rig/us reseried. All specj/icalions and ot/wr i,/brsnationshmi,, were current as ofdaannent relrision date and are subject to change wit/lout notice S CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE cAL FIRE LISTING No. 7170-0026:226 Page 1 of 2 CATEGORY: Control Unit (High-Rise) LISTEE: Simplex, 100 Simplex Drive, Westminster, MA 01441 -0001 Contact: Paul Mattern (978) 731-8542 FAX (978) 731-8881 DESIGN: Models* 4010-9101, -9102, -9201, and —9202 fire alarm control units. Power limited, automatic, manual, local, auxiliary, remote station (protected premises), proprietary (protected premise), waterfiow, and sprinkler supervisory service. Suitable for releasing device service. Refer to listee's data sheet for detailed product description and operational considerations. System components: S 4010-9101, -9102, -9201, -9202 4010-9150 4010-9809,-9829 4010-9810 4010-9816 4010-9817 4010-9821 4010-9806 4010-9811 4010-9812 4010-9813 4010-9814 4010-9818 4010-9819 4010-9820 4010-9823 4010-9824 2081-9046 4010-9860,-9861 4010-9803 Control Unit Standard Function I/O City Circuit Card Event Report DACT Point Report DACT Modular Network Interface RS-485 Net Interlace Class A Adapter Dual RS-232 Interface RS-232 Service Modem Expansion Power Supply Suppression Release Kit Wired Media Module Fiber Optic Media Battery Meter Module Expansion Supply Suppression Release Kit Coil Supervision Module Replacement Door with Annunciator Relay Module RATING: 120, 220, 240 VAC primary; 24 VDC secondary INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating and UL label. 0 Recert. 03-29-2006jw Listing No. 7170-0026:226 Page 2 of 2 APPROVAL: Listed as fire alarm control unit for use with separately listed compatible initiating and S indicating devices. Suitable for high-rise application when installed with model 4003 Series Voice Evacuation System (CSFM Listing No. 6911-0026:196). Refer to listee's Installation Instructions Manual for details. This control unit can generate a distinctive three-pulse Temporal Pattern Fire Alarm Evacuation Signal (for total evacuation) in accordance with NFPA 72, 2002 Edition. *This control unit meets the requirements of UL-864, 9th Edition Standard. NOTE: 1) For Fire Alarm Verification Feature (delay of fire alarm signal), the maximum Retard/Reset/Restart period shall not exceed 30 seconds. 2) Formerly 7165-0026:226 S Recert. 03-29-2006jw This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources. Date Issued: JUNE 4, 2008 Listing Expires June 30, 2009 • Authorized By: BEN HO, Chief Fire Engineering Division fiSimplex S Fire Alarm Control Panel Accessories Cabinet Mounted System Batteries; 2081 Series, Sealed Lead-Acid; 6.2 Ah to 50 Ah Rechargeable, sealed lead-acid design: Lead-calcium grid structure Immobilized electrolyte in absorbent separator High reliability dual seal construction Low maintenance, no need to add water Low self-discharge characteristics One-piece, high impact polystyrene cell cover UL 924.recognized pressure relief valves Available in a variety of capacities: Batteries for internal mounting range from 6.2 Ah up to 50 Ah, depending on control panel cabinet size For applications requiring 110 Ah batteries: Refer to data sheet S4081-0002 for 4100U systems Refer to data sheet S2081-0012 for 4100/4120 series system Ip[*(sll!ItT1 Simplex® rechargeable sealed-lead acid batteries provide reliable and repeatable discharge and recharge characteristics for use in fire alarm and other systems applications. They are designed with immobilized electrolyte in an absorbent separator, allowing them to provide rated capacity on the first cycle. Because of their sealed construction, packaging is allowed within the system electronics enclosure (see illustration on page 2). When this is applicable, the quantity of system cabinets and the battery wiring distances are both minimized. Charging. These batteries are intended to be used with compatible Simplex battery chargers. Series Connections. These batteries are required to be connected in series to produce 24 V system voltage. Battery sets must be of identical voltage, model number, appearance, and approximately the same date of manufacture for proper operation. Testing. Battery capacity testing is recommended to be performed by using a sealed lead-acid battery tester designed to withdraw a minimum of battery charge. The preferred tester applies a variety of amplitude and duration controlled test pulses that compares terminal voltage against those predicted for the specific battery size. (Testing is available through your local Simplex product supplier.) Compatible Sealed Lead-Acid Batteries can be Installed Inside Fire Alarm Control Panel Cabinets I:fl'1.1E71I1171Jij Disposal. Battery chemicals and materials can be recycled. Refer to information shipped with the battery or on its case. Return to the battery manufacturer or to a similarly qualified battery processing facility for proper disposal. Ispecification Summary Nominal Voltage Rating 12 V/battery Discharge Rating 20 Hour Rate Typical Chart/Discharge Cycles 100 to 150 Preferred Charge Temperature Range 60° F to 90° F (15.6°C to 32.2° C) These batteries meet the requirements of UL, ULC. and Factory Mutual for use with respective equipment battery chargers as listed on page 3. Contact your local Simplex product supplier for proper battery selection per system requirements. S2081-0006-16 9/2004 Inner cover Absorbent sej used to imrr e1e Lead-calciur C Typical Construction Details - S Actual appearance will vary with battery size. QaaItl fl, i+flr t%flslflr Cell case (high impact polystyrene) Potting material, black for negative, red for positive (polarity is also clearly marked with + and -) Pressure relief valve Semi-permeable membrane separator S S2081-0006-16 9/2004 Battery Specifications \ Battery Model Capacity @ 20 Hour Width* Depth* Height with Approximate Discharge Rate Terminals Weight* 2081-9272 6.2 Ah 6-1/8" (156 mm) 2-5/8" (67 mm) 4(102mm) 5.75 lbs (2.6 kg) 2081-9274 10 Ah (153 mm) 4-1/16" (103 mm) 4" (102 mm) 9.2 lbs (4.2 kg) 2081-9288 12.7 Ah 6" (153 mm) (102 mm) 4" (102 mm) 9 lbs (4.1 kg) 2081-9275 18 Ah 7-1/4" (184 mm) 3-3/8" (86 mm) 6-5/8" (168 mm) 14.3 lbs (6.5 kg) 2081-9287 25 Ah 6-5/8"(168 mm) (127 mm) 7(178mm) 19.4 lbs (8.8 kg) 2081-9271 (rectangular case, 33 Ah 12-1/2" (318 mm) 3-3/8" (86 mm) 7-1/16" (179 mm) 26.6 lbs (12.1 kg) typically for service) 2081-9276 ("square" case, - 33 Ah 7-3/4" (197 mm) 5-1/4" (133 mm) 6-3/4" (171 mm) 26.5 lbs (12 kg) use for new) 2081-9296 50 Ah 9-1/2" (241 mm) 5-1/2" (140 mm) 8-7/8" (225 mm) 41.8 lbs (19 kg) S * Dimensions and weight are per battery and are for reference only. Exact size may vary. Refer to the chart below for panel mounting compatibility. These batteries are 12 V each and series connected for 24 V system use. NOTE: When installed in a fire alarm control panel, they are to be of identical voltage, appearance, model number, and approximately the same date of manufacture. Battery Compatibility for Fire Alarm Control Panel Mounting NOTE: Refer to individual fire alarm control panel product data sheets for additional battery application information Simplex Control Panel Model Series (see legend and notes below) Battery Capacity 4003 4004 4004R 4005 4006& 4009 4010 4100U 4100 &4120 4020 Model 4008 (all models) (2 or 3 bay) (2, 4 or 6-Unit) (2, 4 or 6-Unit) 2081-9272 6.2 Ah f Jr I I I / I I I / 2081-9274 10 Ah / I I / I I I / I / 2081-9288 12.7 Ah I I I I I I I I I 2081-9275 18 Ah I Note 3 1 Ext Ext Note 2 1 1 1 2081-9287 25 Ah Note 3 Ext I I I Ext 2081-9271 33 Ah Note 3 Ext Note 3 1 Ext Note 4 (rectangular) 2081-9276 33 Ah Note 3 Ext Note 3 / 1 Ext ("square") 2081-9296 50 Ah Note 3 Note 3 1 Ext Ext I = Can be placed in the respective equipment cabinet Ext = External battery cabinet is required, refer to selection chart on page 4 Shaded areas = Not applicable NOTES: These batteries meet the requirements of UL, ULC, and Factory Mutual for use with respective equipment battery chargers listed above. Contact your local Simplex product supplier for proper battery selection per system requirements. 4010 Cabinets will accommodate 2081-9275,18 Ah batteries, but will not allow bottom entry conduit. Use 4081 series companion cabinet and charger, refer to page 4. 4020 Cabinets will accommodate 2081-9271, 33 Ah batteries, but will not allow bottom entry conduit. Some control panel models are listed for battery replacement reference only. S2081-0006-16 9/2004 External Battery Cabinet Compatibility Reference Externally Mounted Battery Battery Cabinets without Chargers Battery Cabinets Chargers (connects to charger in panel) Model * Capacity 2081-9301"" 2081-9303 4081Seriest 2081.9270** 2081-9281 2081-9282 4009-9801 4009-9802 2081-9275 18 Ah I / 2081-9287 25 Ah I I I I I I 2081-9271 (rectangular) 33 Ah 2081-9276 ("square") 2081-9296 50 Ah 1 1 1 1 * Batteries smaller than those listed are normally mounted in the product cabinet. ** Refer to Simplex data sheet S2081-0002 for additional information on these remote battery cabinet/charger products. t Refer to Simplex data sheet S4081-0001 for additional information. 1= Can be placed in the respective equipment cabinet Shaded area = Not applicable : External Battery Cabinet Specification Reference Model Description Color Dimensions - - 2081-9281 2-Unit, 4100 style cabinet without charger, with solid door and battery shelf, primarily intended for 50 Ah batteries Beige 25-3/4W x 20-3/4" H x 6-3/4" D (654 mm x 527 mm x 171 mm) 2081-9282 Red 20819270* External battery cabinet without charger Red 26-1/2" W x 12" H x 12" D (673 mm x 305 mm x 305 mm) 2081-9301 External battery cabinet with charger 2081-9302* External battery cabinet without charger and with meters for voltage and current 2081-9303* External battery cabinet with charger and with meters for voltage and current 4009-9801 For up to 18 Ah External battery cabinet without charger, 16-1/4" W x 13-1/2" H x 4-1/8" D batteries with solid door and battery harness, for close-nippled mounting to fire alarm control Beige (413 mm x 343 mm x 105 mm) For up to 33 Ah 25-3/4" W 20-3/4" H x 4-1/8" 0 4009-9802 batteries panel cabinet (654 mm x 527 mm x 105 mm) 4081 For up to 50 Ah Companion cabinet with charger for the Beige or 22-1/2" W x16-3/4" H x 8-3/8" 0 Series** batteries 4010 and 4004R fire alarm control panel Red (572 mm x 425 mm x 213 mm) * Refer to Simplex data sheet S2081-0002 for additional information. ** Refer to Simplex data sheet S4081-0001 for additional information. Tyco, Simple.t, and the Si,npkx logo are trademarks of Tyco International Services AG or its a/fl/loses in the U.S. and/or oilier countries. 40 .SimplexO Tyco Safety Products Westminster - Westminster, MA • 01441-0001 • USA S20981-0006-16 9/2004 www.tycosafetyproducts-usa-wm.com 02004 Ti'co &i/ètv Prothicis Wesi,ni,,sier. All rig/its reserved. Al/specifications and other in/brniatiom, s/lou,, Here current as of doammnemu ret'icio,, alote and ale sub)cci to change without notice S iSimpIex Multi-Application pen phérals UL, ULC Listed; FM, CSFM, MAPNET Il® or lDNetTM Communicating Devices and MEA (NYC) Approved* Addressable Manual Stations S S Ik'i* Individually addressable manual fire alarm stations with: Power and data supplied via MAPNET II or IDNet addressable communications using a single wire pair** Operation that complies with ADA requirements Pull lever that protrudes when alarmed Break-.rod supplied (use is optional) Models are available with single or double action (breakglass or push) operation UL listed to Standard 38 Compatible with Simplex: Model Series 4010/4100/4120/4020 fire alarm control panels equipped with either IDNet or MAPNET II communications Model Series 2120 communicating device transponders (CDTs) equipped with MAPNET II communications Compact, sealed construction: NEMA 2 enclosure rating for minimal dust infiltration Allows mounting in standard electrical boxes Screw terminals for wiring connections Tamper resistant reset key lock (keyed same as Simplex fire alarm cabinets) Multiple mounting options: Surface or semi-flush with standard boxes or matching Simplex boxes Flush mount adapter kit Adapters are available for retrofitting to commonly available existing boxes The Simplex model 4099-9001 addressable station combines the familiar Simplex manual station housing with a compact communication module that is easily installed to satisfy demanding applications. Its integral individual addressable module (TAM) constantly monitors status and communicates changes to theconnected control panel via MAPNET 11 or IDNet communications wiring. This product has been approved by the California State Fire Marshal (CSFM) pursuant to Section 13144.1 of the California Health and Safety Code. See CSFM Listing 7150-0026:224 for allowable values and/or conditions concerning material presented in this document. Ills subject to re-examination, revision, and possible cancellation. Accepted for use - City of New York Department of Buildings - MEA35.93E. Additional listings may be applicable, contact Simplex for the latest status. 0 2000 Simplex Time Recorder Co. All rights reserved. 4099-9001 Addressable Manual Station (front and side view) PULL D VVN PULL DOWN Op KEY ED E RA ONLY 4099-9002 4099-9003 With 2098-9828 Breakglass Push Institutional Cover kit D ni rtt i r Activation of the Simplex 4099-9001 single manual station requires a firm downward pull to activate the alarm switch. Completing the action breaks an internal plastic break-rod (visible below the pull lever, use is optional). The use of a break-rod can be a deterrent to vandalism without interfering with the minimum pull requirements needed for easy activation. The pull lever latches into the alarm position and remains extended out of the housing to provide a visible indication, Double Action Stations (Breakglass) require the operator to strike the front mounted hammer to break the glass and expose the recessed pull lever. The pull lever then operates as a single action station. Double Action Stations (Push Type) require that a spring loaded interference plate (marked PUSH) be pushed back to access the pull lever of the single action station. Station reset requires the use of a key to reset the manual station lever and deactivate the alarm switch. (If the break-rod is used, it must be replaced.) Station testing is performed by physical activation of the pull lever. Electrical testing can be also performed by unlocking the station housing to activate the alarm switch. MAPNET II and IDNet addressable communications designs are protected by U.S. Patent No. 4,796,025. S4099-0001-5 8/00 nii iuiiini r-nrirrn Addressable Manual Stations Model Description - - - 4099-9001 Single action I - - 4099-9002 Double action, Breakglass operation Addressable manual station, red housing with white letters and white pull lever 4099-9003 Double action, Push operation Accessories Model 2975-9178 Description Surface mount steel box, red - Reference- Refer to page 3 for dimensions 2975-9022 Cast aluminum surface mount box, red 2099-9813 Semi-flush trim plate for double gang switch box, red Typically for retrofit, refer to page 4 2099-9814 Surface trim plate for Wiremold box V5744-2, red 2099-9819 Flush mount adapter kit, black Refer to page 4 for details 2099-9820 Flush mount adapter kit, beige 2099-9803 Replacement breakglass 2099-9804 Replacement break-rod 2099-9828 Institutional cover kit for field installation on 4099-9001 Specifications Power and Communications MAPNET II or IDNet, 1 address per station, up to 2500 ft (762 m) from fire alarm control panel, up to 10,000 ft (3048 m) total wiring distance (including T-Taps) Address Means Dipswitch, 8 position Wire Connections Screw terminal for in/out wiring, for 18 to 14 AWG wire UL Listed Temperature Range 32° to 120° F (0° to 490 C) intended for indoor operation Humidity Range Up to 93% RH at 100° F (38° F) Housing Color Red with white raised lettering Material Housing and pull lever are Lexan® polycarbonate Pull Lever Color White with red raised lettering Housing Dimensions 5" H x 33/4" W xl" D(127 mm x 95 mm x 25 mm) Single Gang Box Mount 4" Square Box Mount Single gang box, 2 1/2" deep 4"(102 mm) square box, 2 1/8" (54 mm) minimum (64 mm), RACO #500 or equal depth, RACO #231 or equal (supplied by others) (supplied by others) LTh çTh Mount flush or with \ maximum extension Oro_ 1/16" (2 mm) _ 4"Square box o 0 - r DO NOT RECESS I (with cover plate) - 0 / Station fi FIRE IIALARM1 I side view Single gang cover plate, 3/4" ________________ (19 mm) extension, RACO #773 PULL DOWN or equal (supplied by others) box outline [j Wall surface'"" Single gang ______ Semi-Flush Mount Side View C S S Simplex Time Recorder Co. 2 S4099-0001-5 8/00 Lr.r.it*i*i1 S 2975-9178 Box 2975-9022 Cast Box Preferred Mounting. For 53/16" H x 4W x 2 3/16"D 5" H x 37/8" W x 2 3/16"D surface mounting of these (132 mm x 102 mm x 56 mm) (127 mm x 98 mm x 56 mm) addressable manual stations, the (ordered separately) (ordered separately) preferred electrical boxes are shown in the illustration to the right. Additional Mounting Knockouts located Reference. Refer to page 4 for top and bottom Wiremold box mounting compatibility. [FIRE ][ALARM11 0 PULL DOWN I lU Access for 3/4" threaded 5" conduit located top and bottom (127 mm) L Simplex) 1"(25.4 mm) 33/4"(95mm) 4099 Series Addressable Manual Station S Surface Mount Side View with Internal Detail Application Reference Field wiring (shown for reference) = Address setting under resealable label (accessible with cover open) Station cover hinges open for installation access Simplex Time Recorder Co. 1 1/4" (32 mm) I Simplex 2975-9178 box 7 (shown for reference) T • (67 mm) - Switch wiring (prewired) 3 Refer to NFPA 72, the National Fire A/ann Code (reference section 5-8), and all applicable local codes for complete requirements for manual stations. The following summarizes the basic requirements. Stations shall be located in the normal path of exit and distributed in the protected area such that they are unobstructed and readily accessible. Mounting shall be with the operable part not less than 3 1/2 ft (1.1 rn) and not niore than 4 1/2 ft ,( 1.37 m) above floor level. At least one station shall be provided on each floor. Additional stations shall be provided to obtain a travel distance not more than 200 ft (61 rn) to the nearest station from any point in the building. When manual station coverage appears limited in any way, additional stations should be installed. S4099-0001-5 8/00 Addressable Manual Station, Additional Mounting Information For retrofit and new installations, additional _________________ Wiremold compatible mounting boxes receptacle box and the required adapter plates 2099-9814 Surface trim model V5744-2 are shown in the illustration to for Wiremold box 5 1/8" H 5"W (supplied by others) the right. (130 mm x 127 mm) Please note that these CD addressable manual stations Two gang switch box, each will also install onto single ~6~x . 3"Hx2"Wx23/4"D gang Wiremold® box model (76 mm x 51 mm x 70 mm) V5747 but will overlap the __________________ (supplied by others) box. Wiremold V5747 c, c? dimensions are: 4 5/8" H x addressable station 2 7/8" W x 13/8" D (117 mm 4099-9001 IDNet LLWN x 73 mm x 35 mm). U 2099-9813 Semi-flush trim for 2 gang 0 switch box, 6" H x 4 1/2"W (152 mm 114 mm) Flush mount adapter kit 2099-9819, Black 2099-9820, Beige k 8' (203 mm) 6- (152 mm) Hole cutout must be a minimum of 6" H by 5" W (152 mm by 127 mm) :1 Wall 4 3/4" (121 mm) surface 6 3/4" (171 mm) Front View HI Box must be recessed into wall - 1" to 11/8" (25.4 mm to 29 mm) 0 : :0 0 - - 411/16" (119 mm) square box, 2 1/8" (54 mm) minimum depth (by others) Side View Simplex, the Simplex logo, MA/WET/I, and IDNet are eli/icr trademarks or registered trademarks of Simplex Time Recorder Co. in the U.S. and/or oilier countries. ,VFPA 72 and Notio,ial Fire A/urn, Code ore registered trademmiarks u/the ,Vatio,,a/ Fire Protectiom, Association (NFPA). Levan is trademark oft/me General Electric Co. fViremnold is a trademmiark oft/ic IVirenmold Company. 54099-0001-5 8/00 Simplex . Westminster, Massachusetts 01441-0001 USA visit us on the world wide web at www.simplexnet.com All specifications and other information shown were current as of printing and are subject to change without notice. S S S CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7150-0026:224 Page 1 of I CATEGORY: Boxes/Pull Stations LISTEE: Simplex, 100 Simplex Drive, Westminster, MA 01441-0001 Contact: Paul Mattern (978) 731-8542 FAX (978) 731-8881 DESIGN: Models 4099-9001, -9002,-9003,-9010, *..goloTsp *..9010TTP -9011, -9012, *..9012TSp *..9012TTp and -9031C non-coded addressable manual pull stations. Models 4099-9001 and -9010 are single action stations. Models 4099-9002 and -9011 are breakglass stations. Models 4099-9003 and -9012 includes a push bar which must be punched in before being able to grab and pull down the actuating handle. Model 4099-9031C is a double action station. Refer to listee's data sheet for additional detailed product description and operational considerations. RATING: 30 VDC INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. is MARKING: Listee's name, model number, electrical rating, and UL label. APPROVAL: Listed as manual pull stations for use with separately listed compatible fire alarm control units. Models are intended for use with listee's Models 4010, 4100,4100U and 4020 control units (CSFM Listing Nos. 7170-0026:226,7165-0026:160 or 7170-0026:187,7170-0026:250 or 7165- 0026:251 and 7165-0026:178). Model 4099-9013C is intended for use with Model 4010 control unit only. For indoor use only. Refer to listee's Installation Instruction Manual for details. *Rev. 09-25-03 This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources. Date Issued: JUNE 4, 2008 Listing Expires June 30, 2009 Authorized By: BEN HO, Chief Fire Engineering Division Simplex TrueAlarm® Analog Sensing UL, ULC Listed; FM, CSFM, TrueAlarm Analog Sensors - Photoelectric, and NYC, MEA Approved* Ionization, and Heat; Compatible Bases and Accessories Iii II*U TrueAlarm® analog sensing provides digital transmission of analog sensor values via MAPNET Il® or lDNetM, two-wire communications** Fire alarm control panel provides: Individual sensitivity selection for each sensor Sensitivity monitoring that satisfies NFPA 72 sensitivity testing requirements Peak value logging allowing accurate analysis for sensitivity selection Automatic, once per minute individual sensor ctij,ition check that verifies sensor integrity Automatic environmental compensation Display of sensitivity directly in percent per foot Multi-stage alarm operation Ability to display and print detailed sensor information in plain English language Photoelectric smoke sensors: Seven levels of sensitivity from 0.2% to 3.7% S Heat sensors: Fixed temperature sensing Rate-of-rise temperature sensing Utility temperature sensing Ionization smoke sensors*: Three levels of sensitivity; 0.5%, 0.9% and 1.3% For use with Simplex®: 4010, 4020, 4100, and 4120 Series control panels Universal Transponders and 2120 TrueAlarm CDTs equipped for MAPNET 11 operation Magnetic test feature Functional and architecturally styled chamber enclosure: Louvered design enhances smoke capture by directing flow to chamber Entrance areas are minimally visible when ceiling mounted Optional accessories include remote LED alarm indicator and output relays UL listed to Standard 268 These products have been approved by the California State Fire Marshal (CSFM) pursuant to Section 13144.1 of the California Health and Safety Code. See CSFM Listings 7272-0026:218, 7271.0026:231, 7270.0026:216, and 7300-0026:217 for S allowable values and/or conditions concerning material presented in this documeni Ills subject to re-examination, revision, and possible cancellation. Accepted for use - City of New York Department of Buildings - MEA35.93E. Refer to page 4 for ULC listing status. Additional listings may be applicable, contact your local Simplex product supplier for the latest status. 4098-9714 TrueAlarm Photoelectric Sensor Mounted in Base [Description Digital Communication of Analog Sensing. TrueAlarm analog sensors provide an analog measurement that is digitally communicated to the host control panel using Simplex addressable communications. At the control panel, the data is analyzed and an average value is determined and stored. An alarm or other abnormal condition is determined by comparing the sensor's present value against its average value and time. Intelligent Data Evaluation. Monitoring each sensors average value provides a continuously shifting reference point. This software filtering process compensates for environmental factors (dust. dirt. etc.) and component aging, providing an accurate reference for evaluating new activity. With this filtering, there is a significant reduction in the probability of false or nuisance alarms caused by shifts in sensitivity, either up or down. Control Panel Selection. Peak activity per sensor is stored to assist in evaluating specific locations. The alarm set point for each TrueAlarm sensor is determined at the host control panel, selectable as more or less sensitive as the individual application requires. Timed/Multi-Stage Selection. Sensor alarm set points can be programmed for timed automatic sensitivity selection (such as more sensitive at night, less sensitive during day). Control panel programming can also provide multi-stage operation per sensor. For example, a 0.2% level may cause a warning to prompt investigation while a 2.5% level may initiate an alarm. Sensor Alarm and Trouble LED Indication. Each sensor base's LED pulses to indicate communications with the panel. If the control panel determines that a sensor is in alarm, or that it is dirt)' or has some other type of trouble, the details are annunciated at the control panel and that sensor base's LED will be turned on steadily. During a system alarm, the control panel will control the LEDs such that an LED indicating a trouble will return to pulsing to help identify the alarmed sensors. TrueAlarm analog sensors and MAPNET 11and lDNetcoiimunications are protected by one or more of the followIng U.S. Patents: 5,155.468; 5.173,683; 5,543,777,5,400,014; 5,552.765; 5,55Z761.4,796,025, DES. 377,460. S4098-0019-8 12/01 TrueAlarm Sensor Bases and Accessories Kiiii'i121tuii*i Base mounted address selection: Address remains with its programmed location Accessible from front (dipswitch under sensor) Automatic identification provides default sensitivity when substituting sensor types Integral red LED for power-on (pulsing), or alarm or trouble (steady on) Locking anti-tamper design Magnetically operated functional test Mounts on standard outlet box 4098-9792, Standard sensor base 4098-9789, Sensor base with wired connections for: 2098-9808 Remote LED alarm indicator or - . 4098-9822 relay (unsupervised) 4098-9791, Sensor base with supervised relay driver output (not compatible with 2120 CDT): Relay operation is programmable and can be manually operated from control panel Use with remote mount 2098-9737 relay Also includes wired connections for remote LED alarm indicator or 4098-9822 relay 2098-9737, Remote or local mount supervised relay: DPDT contacts for resistive/suppressed loads, power limited rating of 3 A 28 VDC; non-power limited rating of 3 A ra, 120 VAC (requires external 24 VDC coil power) 4098-9822, LED Annunciation Relay: Activates when base LED is on steady, indicating local alarm or trouble DPDT contacts for resistive/suppressed loads, power limited rating of 2 A @ 28 VDC; non-power limited rating of 1/2 A 120 VAC, (requires external 24 VDC coil power) 4098-9832, Adapter plate: Required for surface or semi-flush mounting to 4" square electrical box and for surface mounting to 4" octagonal box Can be used for cosmetic retrofitting to existing 6-3/8" diameter base product 2098-9808, Remote red LED Alarm Indicator: Mounts on single gang box ARM (shown in illustration to right) 0 - BSlmp4ex Dtscrintic TrueAlarm sensor bases contain integral addressable electronics that constantly monitor the status of the detachable photoelectric, ionization, or heat sensors. Each sensor's output is digitized and transmitted to the system fire alarm control panel every four seconds. Since TrueAlarm sensors use the same base, different sensor types can be easily interchanged to meet specific location requirements. This feature also allows intentional sensor substitution during building construction. When conditions are temporarily dusty, instead of covering the smoke sensors (causing them to be disabled), heat sensors may be installed without reprogramming the control panel. Although the control panel will indicate an incorrect sensor type, the heat sensor will operate at a default sensitivity providing heat detection for building protection at that location. Irrnrn1-imr.-- Electrical Box Requirements: (boxes are by others) WithoutMIW. 4" octagonal or 4" square, 1-1/2" deep; single gang. 2" deep With 1: 4" octagonal or 4" square, 1-1/2" deep, with 1-1/2" extension ring 4" (102 mm) Square Box 4" (102 mm) Octagonal Box Surface mount reference-. 01-EJ" NH 1-1/2" (38 mm) minimum box depth Flush mount reference, mount even with final surface, or with up to 1/4" (6.4 mm) maximum recess -------------------------------------------------- 2098-9737 Relay (mounts in 4098-9822 Relay (mounts base electrical box or remotely) in base electrical box) Relay Size: 2-1/2" X 1-1/2" X 1" (3.75 cubic inches) (64 mm X 38 mm X 25.4 mm) NOTE: Review total wire count, wire size, and accessories being wired to determine required box volume. 6-3/8(162mm) 4098-9832 Adapter Plate, reauired for 1/4" mounting to surface mounted boxes (6.4 mm) I' 4-7/8" (124 mm) 15/16" (24 mm) L________________ TrueAlarm Bases 4098-9789, -9791, & -9792 S4098-0019-8 12/01 S TrucAlarm heat sensors are self-restoring and provide rate compensated, fixed temperature sensing, selectable with or without-rate-of-rise temperature sensing. Due to its small thermal mass, the sensor accurately and quickly measures the local temperature for analysis at the fire alarm control panel. Rate-of-rise temperature detection is selectable at the control panel for either 15° F (8.3° C) or 20° F (11.1° C) per minute. Fixed temperature sensing is independent of rate-of-rise sensing and programmable to operate at 135° F (57.2° C) or 155° F (68° C). In a slow developing fire, the temperature may not increase rapidly enough to operate the rate-of-rise feature. However, an alarm will be initiated when the temperature reaches its rated fixed temperature setting. TrucAlarm heat sensors can be programmed as a utility device to monitor for temperature extremes in the range from 32° F to 155° F (0° C to 68° Q. This feature can provide freeze warnings or alert to 1-IVAC system problems. (Refer to specific panels for availability.) I.' 4-7/8" (124 mm) 4098-9733 Heat Sensor with Base S TrueAlarm Sensors X I1tII(4 TrucAlarm ohotoelectric sensors use a stable. nulsed Sealed against rear air flow entry Interchangeable mounting EMI/RFl shielded electronics Heat sensors: Selectable rate compensated, fixed temperature sensing with or without rate-of-rise operation Listed to UL Standard 521 for 60 ft (18.3 rn) spacing for 135° F (57.2° C) alarm, and 40 ft (12.2 m) spacing for 1550 F (680 C) alarm Smoke Sensors: Photoelectric or ionization technology sensing 360° smoke entry for optimum response WARNING: In most fires, hazardous levels of smoke and toxic gas can build up before a heat detection device would initiate an alarm. In cases where Life Safety is a factor, the use of smoke detection is highly recommended. infrared LED light source and a silicon photodiode receiver to provide consistent and accurate low power smoke sensing. Seven levels of sensitivity are available for each individual sensor, ranging from 0.2% to 3.7% per foot of smoke obscuration. Sensitivity is selected and monitored at the fire alarm control panel. The sensor head design provides 3600 smoke entry for optimum response to smoke from any direction. A built-in screen keeps insects from entering the smoke chamber. Due to its photoelectric operation. air velocity is not normally a factor, except for impact on area smoke-flow. 4-7/8 (124 mm) "I T LED status indicator (54 mm) 4098-9714 Photoelectric Sensor with Base TrucAlarm Ionization sensors use a single radioactive source with an outer sampling ionization chamber and an inner reference ionization chamber to provide stable operation under fluctuations in environmental conditions such as temperature and humidity. Smoke and invisible combustion gases can freely penetrate the outer chamber. With both chambers ionized by a small radioactive source [Am 241 (Americium)l. a very small current flows in the circuit. The presence of particles of combustion will cause a change in the voltage ratio between chambers. This difference is measured by the electronics in the sensor base and digitally transmitted back to the control panel for processing. Three levels of sensitivity are available for each ionization sensor: 0.5. 0.9, and 1.3% per foot of smoke obscuration. 4-718(124 mm)_.1 T LED status indicator - 2-1/8 (54 mm) 4098-9717 Ionization Sensor with Base v.i.itr.+iMINE Ma (-(iTj Sensor locations should be determined only after careful consideration of the physical layout and contents of the area to be protected. Refer to NFPA 72. the National Fire Alarin Code. On smooth ceilings, smoke sensor spacing of 30 ft (9.1 m) may be used as a guide. For detailed application information, refer to 4098 Detectors, Sensors, and Bases Application Manual (574-709). S4098-0019-8 12/01 TrueAlarm Sensor Bases Model Description Compatibility I Mounting Requirements 1 4098-9792 (C) Standard Sensor Base, no options Sensors 4098-9714, -9733, & -9717 I 4" octagonal or 4" square box,1-1/2" mm. depth, with 3" 0-ring; or single gang box, 2" mm. depth ...;e .Sensors409971 97 £ 9717 I N I S ocaul uaav 'vull I I I ICl.UUI SO Il_Il " 4098-9789 (C) Remote LED Alarm Indicator or 2098-9808 remote LED alarm Unsupervised Relay indicator or 4098-9822 relay Sensor Base with connections for Sensors 4098-9714, -9733, & -9717 4098-9791 (C) Supervised Remote Relay and 2098-9737 remote relay (supervised) Indicator or Unsupervised Relay , 4098-9822 relay (unsupervised) connections for Remote Alarm 2098-9808 remote alarm indicator or TrueAlarm Sensors - Model Description 4098-9714 (C) Photoelectric Smoke Sensor 4098-9717 (C) Ionization Smoke Sensor 4098-9733 (C) Heat Sensor TrueAlarm Sensor/Base Accessories Model Description I compatibility H Bases 4098-9792, 4098-9789, and 4098-9791 Compatibility 4" octagonal or 4" square box with 3" 0-ring, Box depth requirements depend on total wire count and wire size, refer to accessories list below for reference. Mounting Requirements Refer to base requirements Mountina Reauirements Remote Mounting requires 4" octagonal or 2098-9737 Supervised Relay, mounts remote For use with 4098-9791 base 4" square box, 1-1/2" minimum depth or in base electrical box Base Mounting requires 4" octagonal box, 2-1/8" deep with 1-1/2" extension ring 2098-9808 Remote Red LED Alarm Indicator Single gang box, 1-1/2" minimum depth on single gang stainless steel plate Bases 4098-9789 and 4098-9791 . - Relay, tracks base LED status 4" octagonal box, 2-1/8" deep with 1-1/2" 4098-9822 (C) (unsupervised, mounts only in base extension ring electrical box) Required for surface or semi-flush 4098-9832 Adapter Plate Bases 4098-9792, -9789, & -9791 mounted 4" square box without 3" 0-ring, am for surface mounted 4" octagonal box Refer to publication 4098 Defectors. Sensors. and Bases Aoolicafion Manual (574-7091 for additional information. ULC listed model numbers are designated by (C) and require a "C" suffix such as 4098-9794C. General Operatinq Specifications Communications and Sensor Supervisory Power MAPNET II or IDNet, auto-select, 24-40 VDC w/datá, 400 JIA typical, 1 address per base Communications Connections Screw terminals for in/out wiring, 18 to 14 AWG Remote LED Alarm Indicator Current 1 mA typical, no impact to alarm current Remote LED Alarm Indicator and Relay Connections Color coded wire leads, 18 AWG UL Listed Terciperature Range 32° to 100° F (0° to 38° C) Operating with 4098-9717 or 4098 -9733 Temperature Range with 4098-9714 32" to 122" F (0" to 50" C) 15" to 122° F (-9° to 50" C) Humidity Range 10 to 95% RH Smoke Sensor 4098-9714, Photoelectric Sensor Ambient Ratings 4098-9717, Ionization Sensor Air velocity is 0-2000 ft/mm (0-610 m/min) Air velocity is 0-100 ft/mm (0-30 m/min); Altitude is up to 8000 It (2.4 km) Housing Color Frost White 4098-9791 Base With Supervised Remote Relay 2098-9737 (see page 2 for contact ratings) Externally Supplied Relay Coil Voltage 18-32 VDC (nominal 24 VDC) Supervisory Current 270 ijA, from 24 VDC supply Alarm Current with 2098-9737 Relay 28 mA, from 24 VDC supply 4098-9822 Unsupervised Relay, Requirements for Bases 4098-9789 and 4098-9791 (see page 2 for contact ratings) Externally Supplied Relay Coil Voltage 18-32 VDC (nominal 24 VDC) Supervisory Current Supplied from communications Alarm Current 13 mA from separate 24 VDC supply ')'co Simplex, the Simplex logo, 7rueA lava,, MAIWh"l' II, and IDNel are trademarks of7)'co 1,ik'r,,alio,,al Services AG or its affiliates in the U.S.and or other countries. aW"I'A 72 is registered trademark oft/ic National Fire Protection Association (Ni.'PA). 5.Siuuiplex Westminster, Massachusetts 01441-0001 USA www.simplexnet.com S4098-0019-8 12/01 'E', 21)0! Simplex Tune Recorder Co. 1)1/A TIi'PG-US (a i)co company). All rights reserved. All spec(Jlcauiomes and other infrrnmation shoe',, were current as ofdocunwnt revisit,,, date and are subject to change alt/toni notice. S CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. CATEGORY: LISTEE: DESIGN: APPROVAL: 7300-0026:217 Page 1 of 1 Misc. Devices/Control Unit Accessories Simplex, 100 Simplex Drive, Westminster, MA 01441-0001 Contact: Paul Mattern (978) 731-8542 Fax (978) 731-8881 Models 4098-9789, -9789E, 9789TSP, -9789TTP, -9791, -9791 E, -9791T5P, 9791 TTP, -9792, -9792E, -9792TSP, 9792TTP, -9793, -9793E, -9793TSP, -9793TTP, -9794, - 9794TSP, -9794TTP, -9795, -9795T5P, -9795TTP, -9796, -9796TSP, -9796T1P; *GSA4098 9792, *..9793 *..9795 and *..9796 smoke detector bases. These bases act as an interface between the sensor and the MAPNET controller. Bases are intended for use with the following units: Models 4098-9714 and *GsA4098..9714 series photoelectric smoke detector (CSFM Listing No. 7272-0026:218); Model 4098-9717 ionization smoke detector (CSFM Listing No. 7271-0026:231); and Models 4098-9733 and *G5A4098..9733 heat detector (CSFM Listing No. 7270-0026:216). Models 4098-9795, -979515P, -9795TTP, -9796, - 9796T5P, -9796TTP; *G5A4098..9795 and *..9796 are only intended for use with Models 4098-9754 or *GSA4098..9754 photoelectric smoke detector *(CSFM Listing No.7272- 0026:218). Refer to listee's printed data sheet for additional detailed product description and operational considerations. In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. Listee's name, model number, electrical rating, and UL label. Listed as detector bases for use with listee's separately listed compatible fire alarm control units. Refer to listee's Installation Instruction Manual for details Models 4098-9794, -9794TSP, -9794TTP, -9795, -9795TSP, -9795TTP; and *G5A4098..9795 employ a sounder, which is also suitable for use as a fire alarm audible signaling device. These base/sounders CAN NOT produce the temporal code pattern in accordance with NFPA 72, 2002 Edition. If this temporal code is required, the sounder/base unit must be used with the control unit that can produce the temporal pattern. 0 INSTALLATION MARKING Rev. 03-03-2005 This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources. .40 Date Issued: Authorized By: JUNE 3, 2008 BEN HO, Chief Fire Engineering Division Listing Expires June 30, 2009 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE S. LISTING No. 7272-0026:218 Page 1 of 1 CATEGORY-'Photoelectric Smoke Detector LISTEE: Simplex, 100 Simplex Drive, Westminster, MA 01441-0001 Contact: Paul Mattern (978) 731-842 Fax (978) 731-8881 -. DESIGN: Models 4098-9714, -9714TSP, -9714TTP, -9754 -9754TSP, -9754TTP; *G5A4098..9714 and *..9754 analog photoelectric type smoke detectors. Units are intended for use with smoke detector bases Models 4098-9789 9789TSP, -9789TTP, -9791, -9791T5P, -9791TTP, -9792, -9792T5P, 9792TTP, -9793, 9793TSP, -9793TTP, -9794, -97941SP, -9794TTP; *GsA4098,.9792 and *..9793 (CSFM Listing No. 7300-0026:217). Models 4098-9714, -9714TSP and -9714TTP are listed for use with Models 4098-9750, -9751, -9752 and -9753 duct detector units (CSFM Listing No. 3240-0026:220) and Models 4098-9755, -9755TSP and -9755TTP duct detector units (CSFM Listing No. 3240-0026:241). Models 4098-9754, -9754TSP, -9754TTP; *GsA4098..9754 analog photoelectric type smoke detectors employ an integral supplemental heat sensor (1350 F fixed temperature and 1200 F rate of rise). This heat sensor is intended for use as a supplemental device to the smoke detector and is not intended for use in lieu of required heat detectors. Refer to listee's printed data sheet for additional detailed product description and operational considerations. is INSTALLATION: In accordance with listee's printed installation instructions, applicable codes & ordinances and in a manner acceptable to the authority having jurisdiction. Model 4098-9714 with Model 4098-9751 is suitable for installations inside air ducts with air velocities between 0-2000 fpm. MARKING: Listee's name, model number, electrical rating, and UL label. APPROVAL: Listed as photoelectric smoke detectors for use with listee's separately listed Models 4100, 4010, 4020, 4120 and *4008 series fire alarm control units. Refer to listee's Installation Instruction Manual for details. *Rev. 03-03-2005 This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or ' recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources. Date Issued: JUNE 3, 2008 Listing Expires June 30, 2009 Authorized By: BEN HO, Chief Fire Engineering Division r fiSimplex TrueAlarm® Analog Sensing UL, ULC, CSFM Listed; FM Approved; Addressable Duct Sensor Housings with TrueAlarm MEA (NYC) Acceptance* Photoelectric Sensor; Available with Multiple Relay Control S I1tiuii*u Compact air duct sensor housing with clear cover to monitor for the presence of smoke** Includes factory installed TrueAlarm photoelectric smoke sensor and features: Individual sensor information processed by the host control panel to determine sensor status Digital transmission of analog sensor values via lDNetT1 or MAPNET Il®, 2-wire communicationst Programmable sensitivity, consistent accuracy, environmental compensation, status testing, and monitoring of sensor dirt accumulation Model 4098-9755: Basic duct sensor housing (no relay output) powered by lDNet/MAPNET II communications Model 4098-9756: Duct sensor housing with supervised output for multiple remote relays; requires separate 24 VDC; includes one relay Relay output is under panel control At the panel, relay output can be activated manually or in response to a separate alarm or other input General features: UL listed to Standard 268A Clear cover allows visual inspection Test ports provide functional smoke testing access with cover in place Mounts to rectangular ducts or round ducts; minimum size is 8" (203 mm) square or 18" (457 mm) diameter Magnetic test feature for alarm initiation at housing Optional weatherproof enclosure is available separately (refer to data sheet S4098-0032) Diagnostic LEDs (on interface board): Red Alarm/Trouble LED for sensor status and communications polling display Yellow LED for open or shorted trouble indication of supervised relay control (4098-9756 only) Sampling tubes (ordered separately): Available in multiple lengths to match duct size Installed and serviced with housing in place Remote module options (ordered separately): Remote red status/alarm LED (2098-9808) Remote test station with LED (2098-9806) 4098-9843 remote relays (refer to page 2 for details) These products have been approved by the California Stale Fire Marshal (CSFM) pursuant to Section 13144.1 of the California Health and Safely Code. See CSFM Listing 3240.0026.241 for allowable values and/or conditions concerning material presented in this document. It is subject to re-examination, revision, and possible cancellation. Accepted for use - City of New York Department of Buildings - MEA35-93E. Additional listings maybe applicable; contact your local Simplex product supplier for the latest status. Listings and approvals under Simplex Time Recorder Co. are the property of Tyco Safety Products Westminster. om Duct Sensor Housing, Front and Bottom View [Ire 0 L' 2098-9808 2098-9806 Remote Status/Alarm Indicator and Test Station irnrii Operation. Simplex® compact air duct smoke sensor housings provide TrueAlarm operation for the detection of smoke in air conditioning or ventilating ducts. Sampling tubes are installed into the duct allowing air to be directed to the smoke sensor mounted in the housing. Digital Communication of Analog Sensing. Analog information from the sensor is digitally communicated to the control panel where it is analyzed. Sensor input is stored and tracked as an average value with an alarm or abnormal condition being determined by comparing the sensor's present value against its average. Intelligent Data Evaluation. Monitoring each photoelectric sensor's average value provides a software filtering process that compensates for environmental factors (dust, dirt, etc.) and component aging, providing an accurate reference for evaluating new activity. The result is a significant reduction in the probability of false or nuisance alarms caused by shifts in sensitivity, either up or down. Please note that smoke detection in air ducts is intended to provide notification of the presence of smoke in the duct. It is not intended to, and will not, replace smoke detection requirements for open areas or other non-duct applications. t TrueAlarm sensors and tDNet and MAPNET It communications are protected by one or more of the following U.S. Patents: 5,155,468; 5,173,683; 5,543,777; 5.400.014; 5,543,777; 5,710,541; D383,407; D388,352; 0392,573:4,796,025. S4098-0030-5 3/2007 "00919- Typically duct sensor applications require less sensitive settings (such as 2.5% per foot obscuration) due to the ducts being a relative dirty environment. However, the standard seven levels of TrueAlarm sensor sensitivity are available for each individual sensor, ranging from 0.2% to 3.7% per foot of smoke obscuration. Sensitivity is selected and monitored at the fire alarm control panel. INNM M- . Individual smoke sensitivity selection S Model - 4098-9755 Description Basic Duct Sensor Housing; operating power is supplied by either IDNet or MAPNET II communications (no relay output) Compatibility- Simplex fire alarm control panel models 4010, 4020, 4100, 4100U, and 4120. Also 2120 CDT if configured for MAPNET II, TrueAlarm operation Duct Sensor Housing with supervised multiple relay output, Same as above except relay operation is not compatible with 2120 CDT; 4098-9756 requires separate 24 VDC fire alarm power and 4081-9008 Relay output is for up to 15 total 4098-9843 end-of-line resistor harness; includes one 4098-9843 relay Relays (additional relays are ordered separately) Remote LED Indicator and Test Station, Select One if Required Model Description Compatibility Mounting 2098-9808 Red LED status indicator Use single gang box. 2098-9806 Test Station with keyswitch and red LED status indicator 4098-9755 4098-9756 3"H x 2"W x 2"D (turning switch to "TEST" initiates alarm for system testing) (76 mm x 51 mm x 51 mm) N S lIT Control Panel Selection. Peak activity per sensor is stored to assist in evaluating specific locations. The alarm set point for each sensor is determined at the control panel, selectable as the individual application requires. Sensor Status LED. Each sensor housing's red status LED (located on the electrical interface board) pulses to indicate communications with the panel. If the control panel determines that a sensor is in alarm, or that it is dirty or has some other type of trouble, the details are annunciated at the control panel and that sensor housing's status LED will be turned on steadily. During a system alarm, the control panel will control the LEDs such that an LED indicating a trouble will return to pulsing to help identify any alarmed sensors. (Remote Status/Alarm LEDs track the operation of the sensor housing LED.) i.J-flti TrueAlarm photoelectric sensors use a stable, pulsed infrared LED light source and a silicon photodiode receiver to provide consistent and accurate low power smoke sensing. Sensitivity monitoring that satisfies NFPA 72 sensitivity testing requirements Peak value logging allows accurate analysis for sensitivity selection Automatic, once per minute individual sensor calibration check verifies sensor integrity Automatic environmental compensation Smoke sensitivity is displayed in percent p foot Ability to display and print detailed sensor information in plain English language Relays of model 4098-9756 are under panel control R. for ON, OF or override Duct Smoke Sensor Housing with Photoelectric Sensor* Epoxy Encapsulated Remote Relay and End-of-Line Resistor Model Description Compatibility Location Relay; single Form C (7 A © 120 VAC); refer to pages 3 and 4 4098-9756 only; Locate relays within 3 ft 4098-9843 foradditional relay information; one included with 4098-9756; (1 m) of device being wiring is 18 AWG (0.82 mm2 ) color coded wire leads connect up to 15 controlled per NFPA 72 4081-9008 End-of-Line Resistor Harness; 10 kQ, 1/2 W; (ref. 733-894); 4098-9756 At last relay location required to supervise remote relay coil connection * Each duct housing includes an internally mounted model 4098-9714 TrueAlarm photoelectric sensor and an exhaust tube. A correctly sized sampling tube (ordered per application) is required, refer to chart below. I "ii .jj 1111 T"fl rriniv =0 Iii*iiIIiIwrnflf1riTMoll" N Overall Duct Width (305 mm) Tube Required 2098-9796 Suggested Cut Length 1/2" (12.7 mm) longer than duct width to 23" (330mm to 584 mm) 2098-9804 1/2" (12.7 mm) longer than duct width 24" to 46'(610mm to 1168 mm) 2098-9797 2" (51 mm) longer than duct width 46" to 71"(1168 mm to 1803 mm) 2098-9798 1 2" (51 mm) longer than duct width 71" to 95" (1803 mm to 2413 mm) 2098-9799 1 2" (51 mm) longer than duct width S4098-0030-5 3/2007 Duct Sensor Housino Det NOTE: Refer to Installation Instructions 574-776 for additional detail and maintenance information. 11-3/8" (289 mm) I [Exhaust tube accessF] Conduit b others Ii fZ\1 - -- 4098-9714 Smoke sensor, mountad 1 ( n special interface base (supplied) Metal plate with dual holes ...- - .........., . 0 Jill 1! f0r3/4" (19 mm) conduit, plug supplied for unused hole Elr1iLr jj I C) 711213 7,Ta'tr1" (171 m 01 trou ble j Sii1Phng tube a B .2 143 vel: l ED (4098 9756 on,) control I access hole ---: • I- . --- -. I _ QL qn "1 (.statusLEDJ Red sensorl _____ [Sideofdii)-... Mount as shown (preferred) or with electronics area located to the LEFT or UP ONLY (86 mm) 13/16" (21 mm) End View with Duct and Tubes [Duct housing) 118" Round duct outline' (minimum diameter) ] I -I I _______________________________ [Exhaust tuber 18' Square duct outline1 (minimum width) j S •, • . I Sampling tube, keyed for proper hole alignment with holes facing into airflow (template is provided for proper tube installation) 4098-9843 Remote Relay (7 A © 120 VAC, for use with 4098-9756 only) NOTE: Mount in separate electrical box within 3 ft (1 m) of device being controlled per NFPA 72 7 13/16" (21mm) (38 mm) I 1-3/16" (30 mm) 3 S4098-0030-5 3/2007 S Offfiffl- Exhaust Sensor 7 Damper OK Exhaust ..Return ____ 1 II Air I onotlocate sensor here Return air damper Fresh _ air supply Air I Filter '- Sensor Do not locate bank OK sensor here Bend or othe obstruction Return (P 6Duct inlet 6 Duct widths LWidths minimum : . minimum Preferred Duct Sensor Locations: 1. A minimum of six duct widths downstream from bends or inlets to avoid air turbulence. 2. On the downstream side of filters to detect fires in the filters. _____ 3. In return ducts, ahead of mixing areas. Upstream of air humidifier and cooling coil. With accessibility for test and service. For additional information, refer to NFPA 90A, Standardfor the Installation ofAir conditioning and Ventilating Systems. Locations to Avoid: I. Where dampers closed for comfort control would interfere with airflow. 2. Next to outside air inlets (unless the intent is to monitor smoke entry from that area). 3. In return air damper branch ducts and mixing areas where airflow may be restricted. Outdoor Applications Note: For outdoor applications, refer to data sheet S4098-0032 for information on weatherproof enclosure 4098-9845. 11 is] General Mechanical and Environmental Air Velocity Range (linear ft/mm) 300 to 4000 ft/mm (91 to 1220 rn/mm) Sensor Sensitivity Range 0.2% to 3.7% per foot of obscuration, selectable at host control panel UL Listed Temperature Range 32° F to 100° F (0° C to 38° C) Operating Temperature Range 32° F to 122° F (0° C to 50° C) Storage Temperature Range 0° F to 140° F (-18° C to 60° C) Humidity Range 10% to 95% RI-I, non-condensing Wiring Connections Terminal blocks, 18 to 12 AWG (0.82 mm2 to 3.31 mm2 ) Housing Color Remote Status/Alarm LED and Test Station with Remote Alarm LED Current Black base with dear cover Remote Status/Alarm LED 1.2 mA, no impact to 24 VDC alarm current (2098-9808 or 2098-9806) Test Station Keyswitch Current 3.3 mA, no impact to 24 VDC alarm current (2098-9806) Remote Alarm LED and Test Station Distance 250 ft (76 m) maximum Addressable Operation Data Communications IDNet or MAPNET II communications, auto-select, one address per housing; provides operating power to model 4098-9755 Model 4098-9756 with Supervised Multiple Relay Control, Requires Separate Fused 24 VDC from Fire Alarm Power Supply Input Voltage '18-32 VDC (24 VDC nominal) Standby Current 3 mA @ 24 VDC Alarm Current (one relay activated) 15 mA @24 VDC; add 15 mA for each additional remote 4098-9843 relay For use with 4098-9843 relay only, quantity of 15 maximum; distance of 500 ft Supervised Remote Relay Control Output (152 m) maximum; requires 4081-9008 (ref. 733-894)10 kQ, 1/2 Wend-of-line resistor 4098-9843 Relay Output Ratings, Single Form C, use with Model 4098-9756 Only Coil Current 15 mA @24 VDC, up to 15 maximum per relay control output Relay Contacts 7 A at 0.35 PF @ 28 VDC & 120 VAC 250 tA @ 5 VDC Location Distance I 500 ft (152 m) maximum to relay coils: relays must be within 3 ft (1 m) of device being controlled per NFPA 72 Tvco Simpler, the Simpler logo. 7'rueAlwm, lO,Vet, and MA AVE T II are trademarks of Ti'co l,,ternatio,,al Services AG or its a//i/kites in the U.S. and/or oilier countries. NFPA 72 and National Fire Alarm Code are registered trademarks oft/ic National Fire Protection Association (NFPA). 0 Tyco Safety Products Westminster• Westminster, MA • 01441-0001 • USA S4098-0030-5 3/2007 oSimplex www.tycosafetyproducts-usa-wm.com )2OO7 Tyco Safety Products I Vesi,ninster. All rights reserved. All specj/icoiions and other information shown ,i'ere current as ofdocume,,t revision daze and are subject to change without notice. S S CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 3240-0026:241 Page 1 of 1 CATEGORY: Duct Smoke Detector Housing/Base LISTEE: Simplex, 100 Simplex Drive, Westminster, MA 01441 *0001 Contact: Paul Mattern (978) 731-8542 FAX (978) 731-8881 DESIGN: Models 4098-9755, *4098..9755TSp *4098..9755TTp 4098-9756, *4098..9756TSp *4098..9756TTp 4098-9685, 4098-9686, 4098-9687 and 4098-9688 photoelectric type air duct smoke detector units and Model 4098-9841 relay (for Model 4098-9688 only). Unit consists of a listed detector head, base, a sampling and an exhaust tube and an enclosure. Refer to listee's data sheet for additional detailed product description and operational considerations. RATING: Air Velocity: 300 - 4000 feet/mm INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances, and in a manner acceptable to the authority having jurisdiction. isMARKING: Listee's name, model number, electrical & air velocity rating, and UL label. APPROVAL: Listed as duct smoke detector units for installation in HVAC systems when used with separately listed compatible fire alarm control units. Refer to listee's Installation Instruction Manual for details. Rev. 11-06-03 This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources. Date Issued: JUNE 4 2008 Listing Expires June 30, 2009 Authorized By: BEN HO, Chief Fire Engineering Division 5Simplex S UL, ULC Listed; FM Approved* TrueAlert® Multi-Candela Notification Appliances Visible Notification Appliances with Synchronized Flash; Non-Addressable, SmartSyncTM Operation Compatible I1tuii*. Visible only (VIO) 24 VDC notification appliances with high output xenon strobe, available for wall or ceiling mount: UL listed to Standard 1971 Intensity is selectable as 15, 30, 75, or 110 candela with visible selection jumper secured behind strobe housing Operation is compatible with ADA requirements (refer to important installation information on page 3) Polarized input allows connection to compatible reverse polarity, supervised notification appliance circuit (NAC) Regulated circuit design ensures consistent flash output and provides controlled inrush current Rugged, high impact, flame retardant thermoplastic housings are available in red or white with clear lens Strobes provide synchronized flash for with: 4010 Series and 4100U Series fire alarm control panels with NACs selected to provide strobe synchronization or SmartSync two-wire control** 4009 lDNc'1 NAC Extenders is . Separate strobe Synchronization Modules that arc available for Class B or Class A operation Separate SmartSync Control Modules (SCMs) that provide Class B or Class A output from conventional NAC inputs Strobe housings provides flexible, easy, and convenient semi-flush or surface wall mounting: Rear of housing does not extend into box Wall mount strobes easily mount to single gang, double gang, or 4-inch square outlet box Ceiling mount strobes mount to single gang boxes Wall mount strobe features: Wiring terminals are accessible from the front of the housing providing easy access for installation, inspection, and testing Covers are available separately to convert housing color Optional adapters and wire guards: Wall mount strobe adapters are available to cover surface mounted electrical boxes and to adapt to Simplexk 2975-9145 boxes UL listed red wire guards are available for wall or ceiling mount strobes This product was not approved by CSFM or MEA (NYC) as of document revision date. Refer to page 2 for listing status of wire guards. Additional listings may be applicable; contact your local Simplex product supplier for the latest status. Listings and approvals under Simplex Time Recorder Co. are the property of Tyco Safely Products Westminster. Simplex two-wire strobe synchronization operation is protected by U.S. patent No. 5.559.492 and SmartSync horn/strobe operation is protected under U.S. Patent No. 6,281,789. Wall Mount Strobes !-•- FIRE i l• \.. '.. I JJI I \jJ Ceiling Mount Strobes I Discrintinn Multi-Candela TrueAlert synchronized strobes provide convenient installation to standard electrical boxes. The enclosure designs are both impact and vandal resistant and provide a convenient strobe intensity selection. Since each model can be selected for intensity output, on-site model inventory is minimized and changes encountered during construction can be easily accommodated. Wall mount strobe housings arc a one-piece assembly (including lens) that mounts to a single or double gang, or 4" square standard electrical box. The cover can be quickly removed (a tool is required) and covers are available separately for color conversion. Ceiling mount strobes install using standard single gang electrical boxes. Color choice is determined by model number. During installation, a selection plug at the back of the housing determines the desired strobe intensity. An attached flag with black letters on a highly visible yellow background allows the selected intensity to be seen at the side of the strobe lens. Strnhcv Annlir.itinn Rfirnnc Proper selection of visible notification is dependent on occupancy, location, local codes, and proper applications of: the National Fire Alarm Code (NFPA 72), ANSI Al 17.1; the appropriate model building code: BOCA, ICBO, or SBCCI; and the application guidelines of the Americans with Disabilities Act (ADA). S4906-0001 4/2004 Multiple Strobes. When multiple strobes and their reflections can be seen from one location, synchronized flashes reduce the probability of photo-sensitive reactions as well as the annoyance and possible distraction of random flashing. These multi-candela strobes are synchronized over a two-wire circuit when connected to compatible NACs, to compatible Synchronized Flash Modules, or to SmartSync Control Modules. iVi'fl T. 7I Some applications desire the audible notification appliances to be capable of being silenced before the alarm condition is reset (on-until-silenced) while the visible notification appliances are kept activated until the alarm condition is reset (on-until-reset). SmartSync operation mode provides this function using a single circuit (two-wire operation). Multi-Candela Visible Notification Appliances (Strobes) Model I Mounting I Housing Color I "FIRE" Lettering 4906-9101 I Red I White Wall I I 4906-9103 White I Red 4906-9102 1 Red I White Ceiling 4906-9104 White I Red Class B SmartSync two-wire control is available from: 0 4100U and 4010 Fire Alarm Control Panels; 4010 panels require operating software Revision 2.X or higher (refer to data sheet S4010-000I for details; refer to data sheet S4100-0031 for basic 4100U information) 4009 IDNet NAC Extender, models 4009-9201 and 4009-9301 (refer to data sheet S4009-0002) SmartSync Control Module (SCM) 4905-9938, converts separate conventional horn and strobe NAC inputs into a SmartSync NAC output; up to eight SCMs can be synchronized to each other Class A SmartSync two-wire control is available from 4100U NACs and from the 4905-9938 SCM. Additional SmartSync compatible notification appliances include separate horns and combination horn/strobe notification appliances. Description Multi-candela strobe with intensity selectable as: 15, 30, 75, or 110 candela; synchronized flash rate; SmartSync two-wire control compatible S Wall Mount Strobe Adapters Model Description - - Dimensions 4905-9937 Red Surface Mount Adapter Skirt; use to cover 1-1/2" (38 mm) . 5-3/8" H x 5-1/4" W x 1-5/8° D 4905-9940 White deep surface mounted boxes (136 mm x 133 mm x 41 mm) Total depth with strobe = 4-3/8" (111 mm) 4905-9931 Red Adapter Plate for mounting to Simplex 2975-9145 box (typically for 8-5/16" x 5-3/4" x 0.060° Thick retrofit, may be mounted vertical or horizontal) (211 mm x 146 mm x 1.5 mm) 2975-9145 Red Mounting Box, requires Adapter Plate 4905-9931 7-7/8" x 5-1/8" x 2-3/4" 0 (200 mm x 130 mm x 70 mm) Ceiling Mount Strobe Adapter Model Description - I Dimensions 4905-9910 Surface Mount Adapter Plate; zinc plated; required for mounting to 4-7/8" x 3-1/8" x 0.060" D handy box; not needed when using 4905-9926 guard (124 mm x 79 mm x 1.5) Synchronization Modules (refer to data sheet S4905-0003 for additional information) Model Description I. - Dimensions 4905-9914 Class B I Synchronized Flash Module; epoxy encapsulated with I 1-3/8" x 2-7/16" x 13/16" in/out 18 AWG (0.82 Min) wire leads, rated for 2 A NAC, I 4905-9922 Class A requires 10 mA for power (35 mm x 62 mm x 20 mm) 4905-9938 SmartSync Control Module with Class B or Class A output; mounts in 4" (102 mm) square box Replacement Covers and Guards Model Description 4905-9992 Red cover with white "FIRE" lettering For Wall mount strobes 4905-9993 White cover with red "FIRE" lettering 4905-9961 Wa ling mount l mount I Red wire guard with mounting plate, compatible with 49059926* Ceil semi-flush or surface mounted boxes * UL listed by Space Age Electronics Inc. 2 4" x 4-1/8° x 1-1/4° D (102mmx 105mmx32mm) Dimensions 5-1/8" H x 5" W x 1-1/2" D (130mmx 127mmx38mm) 6-1/16°Hx6-1/16"Wx3-1/8"D (154 mm 154 mmx79 mm) 6-1/8" x 4-3/8" x 2-7/8" deep (156mmx111 mmx73mm) S4906-0001 4/2004 IMPORTANT! WALL MOUNT INSTALLATION HEIGHT REFERENCE Bottom of lens is either even with, or slightly Electrical above bottom \4 outline of compatible rbox boxes NFPA 72 requires 80" (2.03 m) that the entire lens minimum be not less than 80" and not greater than 96" above the finished floor 10 Mounting is compatible with single gang, double gang, and 4° (102 mm) square boxes, 1-1/2" (38 mm) deep, by others Wiring access hole S S Strobe Specifications Wall Mount or Ceiling Mount, Common Specifications Rated Voltage Range UL Listed Rating ULC Listed Rating Regulated 24 VDC; see Note 1 below 20 voc to 30 VDC per ULC S526-M878 Flash Rate 1 Hz Synchronized NAC Loading Up to 35 synchronized strobes maximum per NAC Temperature Range 32° to 122° F (0° to 50° C) Humidity Range 10% to 93%, non-condensing at 100° F (38° C) Connections Terminal blocks for 18 AWG to 12 AWG (0.82 mm2 to 3.31 mm2): two terminal for in/out wiring wires per Housing Dimensions (with lens) 5-1/8° H x 5" W x 2-3/4" D (130 mm x 127 mm x 70 mm) Wall Mount Maximum RMS Current Rating per Strobe Setting (see.Note 2 below) 15 cd 30 cd 75 cd 110 cd 60 mA 94 mA 186 mA 252 mA Reference RMS Currents 18 VDC at other voltages 24 VDC 55 mA 85 mA 169 mA 226 mA 41 mA 63 mA - - 123 mA 164 mA Housing Dimensions (with lens) 4-3/4" L x 2-5/16" W x 2-5/8" D (121 mm x 75 mm x 67 mm) Ceiling Mount Maximum RMS Current Rating per Strobe Setting (see Note 2 below) 15 cd 30 cd 75 cd 110 cd 75 mA 125 mA 233 mA 316 mA Reference RMS Currents 18 VDC at other voltages -. 24 VDC 64 mA . 102 mA 199 mA 266 mA 49 mA 76 mA 146 mA 195 mA NOTES: "Regulated 24 VDC" refers to the voltage range of 16 to 33 VDC per UL Standard 1971, Signaling Devices for the Hearing Impaired, changes effective May 1, 2004. This voltage range is the absolute operating range. Operation outside of this range may cause permanent damage to the strobe. Please note that 16 VDC is the lowest operating voltage that is allowed at the last appliance on the NAC under worst case conditions. The maximum RMS current listed is the device nameplate rating. Strobe designs are constant wattage and the maximum RMS current rating occurs at the lowest allowable operating voltage. (RMS is root mean square and refers to the effective value of a varying current waveform.) Installation Reference, Surface or Semi-Flush Wall Mounting Removable cover Strobe intensity (tool required) viewing slot S4906-0001 4/2004 Ceiling Mount Strobe Installation Reference Single gang box (Wiremold V5744S) 2-1/4" (57 mm) deep, supplied by othersj Handy box, 1-1/2" ( 38 mm) deep (RACO 650 or equal) or single gang box, 2-1/2" (64 mm) deep (RACO 519 or equal) supplied by others Also can be attached to boxes mounted to drop ceiling T-bar with clips (ERICO No. 512 or equal) 4905-9910 Adapter Plate, required for surface mount with handy box unless using the 4905-9926 wire guard Ceiling mount strobe Optional 4905-9926 wire guard with mounting plate --Stro6e71 - - - - - - - - - - - - - ntensity - viewing slot Intensity selection plug, accessible only from rear of lens' LI--- housin factory setting is 15 cd -------------------- Wall Mount Installation Reference; Adapter Plate, Guard, and Adapter Skirt S S 45 iii o riroi U ° / / IoiI 4905-9931 Adapter Plate 4905-9961 Optional Wire Guard (shown here for reference only, 4905-9931 Adapter Plate) can be used on other mounting options) Surface Mounting Reference with Optional Adapter Skirt and Optional Wire Guard Surface mount conduit and box shown for reference 4"(102m m) square box profile, 1-1/2" (38 mm) deep Optional 4905-9961 Wire Guard Strobe Optional Surface Mount Adapter Skirt, 1-1/2" deep: 4905-9937, Red; 4905-9940, White (conduit knockouts are provided on all four sides) S Tyco, Simplex. the Simplex logo. IDNe,. TrucA let!, and Smart5vnc are trademarks of Tyco International AG or its ajJihates in the U.S. and/or other countries. NFPA 72 and National Fire Alan;i Code are registered trademarks u/the National Fire Protectio,, Association (,VFPA). Tyco Safety Products Westminster• Westminster, MA 01441-0001 • USA S4906-0001 4/2004 .Simplex www.tycosafetyproducts-usa-wm.com t2004 Two Safety Prochicts West,,,inste, All rights resen'ed. All specj/ications and other information shun',, were current as of'doani,eni reiisio,i date and are subject to change without notice. CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE CAL FIRE LISTING No. 7125-0026:316 Page 1 of 1 CATEGORY: Fire Alarm Devices for the Hearing Impaired LISTEE: Simplex, 100 Simplex Drive, Westminter, MA 01441-0001 Contact: Paul Mattern (978) 731-8542 Fax (978) 731-8881 DESIGN: Models 4906-9101, -9102, -9103, and -9104 multi-candela, non-addressable, synchronizable strobe lights. Models 4906-9101 and —9103 are for wall mount. Models 4906-9102 and —9104 are for ceiling mount. Synchronizing modules are required for synchronizing strobe lights if the interconnected control unit does not provide NAC synchronization capabilities. Refer to listee's data sheet for additional detailed product description and operational considerations. RATING: Electrical: 16-33 VDC Candela: 15, 30, 75, and 110 cd INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. 40 MARKING: Listee's name, model number, electrical rating and UL label. APPROVAL: Listed as strobe lights for use with separately listed compatible fire alarm control units. For indoor use only. Refer to listee's Installation Instruction Manual for details. These units can generate a distinctive three-pulse Temporal Pattern Fire Alarm Evacuation Signal (for total evacuation) in accordance with NFPA 72, 2002 Edition. 06-23-04 This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources. Date Issued: JUNE 4, 2008 Listing Expires June 30, 2009 Authorized By: BEN HO, Chief Fire Engineering Division S i®SimpIex UL, ULC Listed; FM Approved* TrueAlert® Multi-Candela Notification Appliances Visible Notification Appliances with Horn and Synchronized Flash; Non-Addressable, SmartSyncTM Operation Compatible S I1iuit* Audiblelvisible (NV) notification appliances with efficient electronic horn and high output xenon strobe, available for wall or ceiling mount . Operation is compatible with ADA requirements (refer to important installation information on page 3) Rugged, high impact, flame retardant thermoplastic housings are available in red or white with clear lens Operates over a two-wire SmartSync circuit to provide: Horns that are controlled separately from strobes on the same two-wire circuit "On-until-silenced" änd,"on-until-reset" operation on the same two-wire pair Horn control that can be selected to be temporal coded, march time coded, or on continuously Strobe appliances on the same circuit operating at a synchronized 1 Hz flash rate Class B (Style Y) operation requires connection to a compatible SmartSync NAC or to SmartSync Control Module (SCM) 4905-9938 Class A (Style Z) operation when connected to the 4905-9938 SCM or with 4l 00U series lire alarm control panel NACs Wall mount A/Vs features: Wiring terminals are accessible from the front of the housing providing easy access for installation, inspection, and testing Covers are available separately to convert housing color Optional adapters and wire guards: Wall mount AN adapters are available to cover surface mounted electrical boxes and to adapt to Simplex® 2975-9145 boxes UL listed red wire guards are available for wall or ceiling mount A/Vs Visible notification appliance (strobe): 24 VDC xenon strobe; intensity is selectable as 15, 30, 75, or 110 candela with visible selection jumper secured behind strobe housing UL listed to Standard 1971 Regulated circuit design ensures consistent flash output and provides controlled inrush current Audible notification appliance (horn): Low current, 24 VDC electronic horn with harmonically rich output sound suitable for either coded or steady operation UL listed to Standard 464 :j FIRE è7 0 _ Wall Wall and ceiling Mount A/Vs Dnsrintic Multi-Candela TrueAlert A/Vs with horn and synchronized strobe provide convenient installation to standard electrical boxes. The enclosure designs are both impact and vandal resistant and provide a convenient strobe intensity selection. Since each model can be selected for strobe intensity output, on-site model inventory is minimized and changes encountered during construction can be easily accommodated. Wall mount AN housings are a one-piece assembly (including lens) that mounts to a single or double gang, or 4" square standard electrical box. The cover can be quickly removed (a tool is required) and covers are available separately for color conversion. Ceiling mount ANs install using standard 4" electrical boxes. Color choice is determined by model number. During installation, a selection plug at the back of the housing determines the desired strobe intensity. An attached flag with black letters on a highly visible yellow background allows the selected intensity to be seen at the side of the strobe lens. * This product was not approved by CSFM or MEA (NYC) as of document revision date. Refer to page 2 for listing status of wire guards. Additional listings may be applicable; contact your local Simplex product supplier for the latest status. Listings and approvals under Simplex Time Recorder Co. are the property of Tyco Safety Products Westminster. Simplex two.wire strobe synchronization operation is protected by U.S. patent No. 5,559,492 and SmariSync horn/strobe operation is protected under U.S. Patent No. 6,281,789. S4906-0002 4/2004 Proper selection of visible notification is dependent on occupancy, location, local codes, and proper applications of: the Notional Fire Alai-in Code (NFPA 72), ANSI Al 17.1; the appropriate model building code: BOCA, ICBO, or SBCCI; and the application guidelines of the Americans with Disabilities Act (ADA). U1FI-7 Multiple Strobes. When multiple strobes and their reflections can be seen from one location, synchronized flashes reduce the probability of photo-sensitive reactions as well as the annoyance and possible distraction of random flashing. The multi-candela strobes of these ANs are synchronized by the controlling SmartSync operation NAC. iI fl7 I SmartSync operation mode allows a two-wire circuit to provide the ability to activate both the horn and strobe on the same NAC and then allow the horn to be silenced while the strobe remains flashing. The horn operates as "on-until-silenced" while the strobe operation is "on-until-reset." 4100U and 4010 Fire Alarm Control Panels (refer to data sheet S4010-0001 for details; refer to data sheet S4100-0031 for basic 4100U information) 4009 lDNet NAC Extender (refer to data sheet S4009-0002) SmartSync Control Module (SCM) 4905-9938 (refer to data sheet S4905-0003) S Additional SmartSync compatible notification appliances include separate horns and combination horn/strobe notification appliances. -. - \\Multi-Candela A/Vs Model Mounting I Housing Color I 'FIRE" Lettering I Description 4906-9127 I Red I White I 4906-9129 Wall White Red Horn with Multi-Candela Strobe; strobe intensity selectable as: 15, 30, 75, or 110 candela; operates with SmartSync two-wire 4906-9128 I Red I White control 4906-9130 Ceiling White I Red I Wall Mount AN Adapters Model Description - - - Dimensions 4905-9937 Red Surface Mount Adapter Skirt; use to cover 1-1/2" (38 mm) deep 5-3/8" H x 5-1/4" W x 1-5/8" D (136 mm x 133 mm x 41 mm) 4905-9940 White surface mounted boxes depth with strobe = 4-3/8" (111 mm) 4905-9931 Red Adapter Plate for mounting to Simplex 2975-9145 box (typically for 8-5/16" x 5-3/4" x 0.060" Thick ___________ retrofit, may be mounted vertical or horizontal) (211 mm x 146 mm x 1.5 mm) C 2975-9145 Red Mounting Box, requires Adapter Plate 4905-9931 (200 mm 130 min x70 mm) SmartSync Control Module Model Description Dimensions 4905-9938 SmartSync Control Module with Class B or Class A output; mounts in 4" 4" x 4-1/8" x 1-1/4" D (102 mm) square box; refer to data sheet S4905-0003 for details (102 mm x 105 mm x 32 mm) Replacement Covers for Wall Mount A/Vs Model Description - - - . Dimensions 4905-9992_- - Red cover with white "FIRE" lettering 5-1/8" H x 5" W x 1-1/2" 0 4905-9993 White cover with red "FIRE" lettering (130 mm x 127 mm x 38 mm) Wire Guards and Ceiling Mount AN Adapter Model Description - Dimensions 4905-9961 Wall mount red wire guard with mounting plate, compatible with semi-flush 6-1/16" H x 6-1/16" W x 3-1/8" 0 or surface mounted boxes (154 mm x 154 mm x 79 mm) 49059927* Ceiling Red Wire Guard for mounting to flush mounted electrical box (216 mm 156 mm x 76 mm) 9" x 7" 49059928* Red Adapter Plate, required to mount guard to surface Mount mounted electrical box (229 mm x 178 mm) 4-3/4" x 6-7/8" x 1-1/2" deep, • (121 mm x 175 mm x 38 mm) 4905-9915 White Surface Mount Adapter Box Extension, use to cover 1-1/2" deep surface mounted boxes 4905-9916 Red * UL listed by Space Age Electronics Inc. 2 S4906-0002 4/2004 VVhYI-1t1r.]ii. Wall Mount or Ceiling Mount, Common Specifications Rated Voltage Range UL Listed Rating ULC Listed Rating Regulated 24 VDC' see Note 1 below 20 VDC to 30 VDC per ULC S526-M878 Flash Rate and Synchronized NAC Loading 1 Hz; with up to 35 synchronized strobes maximum per NAC Environmental; Temperature and Humidity 32° to 122° F (0° to 50° C); 10% to 93%, non-condensing at 100° F (38° C) Connections Terminal blocks for 18 AWG to 12 AWG (0.82 mm2 to 3.31 mm2) ; two wires per terminal for in/out wiring Horn Output Characteristics 2400 to 3700 Hz sweep, modulated at 120 Hz rate Voltage Horn Output Ratings Sound Type (see Note 2) © 10 It (3 m) Reverberant Chamber, UL 464 Test Anechoic Chamber 16 VDC 24 VDC 33 VDC Steady Coded Steady Coded Steady Coded 86 dBA 82 dBA 88 dBA 84 dBA 90 dBA 86 dBA 92 dBA 91 dBA 94 dBA 95 dBA 96 dBA 96 dBA Housing Dimensions (with lens) 5-1/8" H x 5" W x 2-3/4" D (130 mm x 127 mm x 70 mm) Wall Maximum RMS Current Rating per Strobe Setting (see Note 3 below)Mount 15 cd 30 cd 75 cd 110 cd 75 mA 116 mA 221 mA 285 mA Reference RMS Currents 18 VDC at other voltages 24 VDC 70 mA 101 mA 184 mA 243 mA 60 mA 84 mA 143 mA 185 mA Housing Dimensions (with lens) 4-3/4 L" x 6-7/8" W x 2-5/8" D (121 mm x,175 mm x 67 mm) CeilingStrobe Mount Maximum RMS Current Rating per Setting (see Note 3 below) 15 cd 30 cd 75 cd 110 cd 86 mA 132 mA 250 mA 320 mA Reference RMS Currents 18 VDC at other voltages 24 VDC 81 mA 119 mA 216 mA 283 mA 70 mA 97 mA 167 mA 217 mA NOTES: "Regulated 24 VDC" refers to the voltage range of 16 to 33 VDC per UL Standard 1971 Signaling Devices for the Hearing Impaired, changes effective May 1, 2004. This voltage range is the absolute operating range. Operation outside of this range may cause permanent damage to the appliance. Please note that 16 VDC is the lowest operating voltage that is allowed at the last appliance on the S NAC under worst case conditions. Coded values are typical of the output measured with a Temporal coded or a March Time coded pulse and with a sound level meter reading on a "fast" setting. Under the same test conditions, coded horn output "peak" sound level readings are typically 4 dBA higher. Currents are with horn on steady. The maximum RMS current listed is the device nameplate rating. Strobe designs are constant wattage and the maximum RMS current rating occurs at the lowest allowable operating voltage. (RMS is root mean square and refers to the effective value of a varying current waveform.) Mounting is compatible with single gang, double gang, and 4" (102 mm) square boxes. 1-1/2" (38 mm) deep, by others Wiring access hole Wiring terminals for SmartSync operation Removable cover Strobe intensity (tool required) viewing slot IMPORTANT! WALL MOUNT INSTALLATION HEIGHT REFERENCE Bottom of lens is either even with, or slightly r .....,,—Electrical above bottoms ii r box outline of compatible \ hi boxes NFPA 72 requires 80" (2.03 m) that the entire lens minimum be not less than 80" and not greater than 96" above the finished floor S4906-0002 4/2004 Ceiling Mount AN and Guard Installation Reference Ceiling reference, 4 (102 mm) square box, surface mounted box 1-1/2"(38 mm) minimum depth VSY,Ceiling reference, - flush mounted box Optional 4905.99151:9916 Adapter, recommended for surface mounted box . Wiring terminals are J' located behind the housing Optional 4905-9928 Adapter Plate, required for surface mounted electrical box Four mounting clamps included, two each side - Optional 4905-9927 Red Wire Guard ----------------------------------- 'Ile Strobe intensity viewing slot Intensity selection plug, accessible only from rear of lens housing; factory setting is 15 cd Wall Mount Installation Reference; Adapter Plate, Guard, and Adapter Skirt Lel Surface Mounting Reference with Optional Adapter Skirt and Optional Wire Guard Surface mount conduit and box shown for reference 4" (102 mm) square box profile, 1-1/2" (38 mm) deep Optional 4905-9961 Wire Guard NVlop 0 4905-9931 Adapter Plate 4905-9931 Adapter Plate 4905-9961 Optional Wire Guard (shown here for reference only, can be used on other mounting options) Optional Surface Mount Adapter Skirt, 1-1/2" deep: 4905-9937, Red: 4905-9940, White (conduit knockouts are provided on all four sides) Tyco, Simplex, the Simplex logo, lONe!, TrswAlerj, and SinariSync are trademarks of Tvco International AG or its al/iliates in the U.S. and/or other countries. NFPA 72 and National Fire Alarm ('ode are registered trademarks oft/se National Fire Protection Associatio,, (NFPA). 1SirripIex Tyco Safety Products Westminster• Westminster, MA • 01441-0001 • USA S4906-0002 4/2004 www.tycosafetyproducts-usa-wm.com @2004 7)vo Sqftny Psvthscts Westminster. All rights reserved. All specf/ications and other inJiwmation shown nent current as ofdoewnent rev/slot, date and are subject to change without notice. CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7125-0026:317 Page 1 of I CATEGORY: Fire Alarm Devices for the Hearing Impaired LISTEE: Simplex, 100 Simplex Drive, Westminter, MA 01441 Contact: Paul Mattern (978) 731-8542 FAX (978) 731-8881 DESIGN: Models 4906-9127, 4906-9129 wall mount and Models 4906-9128 and 4906-9130 ceiling mount multi-candela horn/strobes. Refer to listee's data sheet for detailed product description and operational considerations. RATING: Electrical: 16-33 Vdc -Candela: 15, 30, 75, ll0cd INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances, and in a manner acceptable to the authority having jurisdiction. For indoor use only. MARKING: Listee's name, model number, electrical/candela rating, and UL label. S APPROVAL: Listed as multi-candela horn/strobes with a signaling appliance suitable for the hearing impaired when used with listee's separately listed fire alarm control units. All models require the use of Model 4905-9938 (CSFM Listing No. 7125-0026:235) sync control module unless the horn/strobes are used with the listee's Model 4010 (CSFM Listing No. 7170-0026:226) or 4100 (CSFM Listing Nos. 7170-0026:250 and 7165-0026:251). Refer to listee's Installation Instruction Manual for details. 07-22-2004 This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources. S Date Issued: Authorized By: JUNE 4,'2008 BEN HO, Chief Fire Engineering Division Listing Expires June 30, 2009 S tqco /Fire & IS implex6rinneff Security SimplexGrinnell LP 9855 Carroll Canyon Road San Diego, CA 92131 Tele: (858) 740-0100 Fax: (858) 740-0156 www.simplexgrinnell.com APPENDIX ITEM DESCRIPTION A BUSINESS LICENSE B - WARRANTY S . 4/14/2009 REV.#: 0 PROJECT #: L S License Number: 802591 Extract Date: 10/01/2008 SIMPLEX GRINNELL L P Business Information: 900 ALLEN AVENUE GLENDALE, CA 91201 Business Phone Number: (561) 988-3755 Entity: . Partnership Issue Date: 12/28/2001 Expire Date: 12/31/2009 License Status: This license is current and active. All information below should be reviewed. Classifications: Classifications: DESCRIPTION . CIO ELECTRICAL C16 FIRE PROTECTION CONTRACTOR This license filed Contractor's Bond number 81880913 in the amount of $12,500 with the bonding company FEDERAL INSURANCE COMPANY. Effective Date: 01/01/2007 Contractor's Bonding History, - S . This license filed Bond of Qualifying Individual number 82056155 for KARIM MAZHAR in Bonding: 1 ' the amount of $12,500 with the bonding company FEDERAL INSURANCE COMPANY. Effective Date: 01/01/2007 BQI's Bonding History This license filed Bond of Qualifying Individual number 81880915 for RONALD GILBERT MAYLE in the amount of $12,500 with the bonding company FEDERAL INSURANCE 2. COMPANY. Effective Date: 01/01/2007 BQI's Bonding History This license has workers compensation insurance with the AMERICAN HOME ASSURANCE COMPANY Policy Number: WC1616749 Workers' Compensation: - Effective Date: 06/29/2008 Expire Date: 10/01/2008 Workers' Compensation History Miscellaneous Information: 10/28/2005 ASB CERTIFICATION REMOVED p •• SimplexGrinnell LP 3568 Ruffin Road, South If San Diego, CA 92123-2597 tL,CE1 1F/re & Security / SimplexGrinne Tele: (858) 633-9100 10 / Fax: (858) 633-9101 www.simplexgrinnell.com SIMPLEXGRINNELL WARRANTY WARRANTY & DAMAGES: SimplexGrinnell hereby warranties for one (1) year from the date of beneficial use or eighteen (18) months from date of delivery to the purchaser to replace, or at its option, to repair any equipment or parts thereof which are found to be defective in material or workmanship. This warranty is made to the purchaser of this equipment and is in lieu of all other warranties, expressed or implied, including any implied warranty of merchantability of fitness for a particular purpose. SimplexGrinnell shall not be liable for any direct, incidental or consequential loss of damage to the purchaser or user of this equipment arising out of the failure of the equipment to operate in excess of the purchase price of said equipment. This warranty is solely limited to the equipment as provided by SimplexGrinnell in this submittal and excludes associated field wiring and/or any equipment to which the submitted equipment may be attached or connected. WARRANTY SERVICE HOURS: - 8:00AM TO 17:OOPM, MONDAY THROUGH FRIDAY, EXCLUDING LOCALLY OBSERVED SIMPLEX HOLIDAYS. - OFF HOURS RESPONSE IS AVAILABLE AT EXTRA COST. 12/27/2007 REV.#: 0 PROJECT #: 480-XXXXXX-XX I XXXXXXXXX NFPA Record of Completion Name a Address Rep. of Authority Having Jurisdiction Address / Phone Number Type(s) of System or Service: NFPA 72, Chapter 3 - Local if alarm is transmitted to location(s) off premise, list where received: FILE COpy NFPA 72, Chapter 3 - Emergency Voice /Alarm Service: Frequency Quantity of voice/alarm channels Single: Multiple: Quantity of speakers installed: Quantity of speaker zones: Quantity of telephones or telephone jacks included in the system: NFPA 72, Chapter 4 - Auxiliary Indicate type of connection: Local Energy, Shunt, Parallel Telephone Location and telephone number for receipt of signals: NFPA 72, Chapter 4 - Remote Station Upon comjAlarm: authority h Supervisory: NFPA 72, Chapter 4 - Proprietary If alarms are retransmitted to public fire service communications center or others, indicate location and telephone number of the organization receiving alarm: Indicate how alarm is retransmitted: Y NFPA 72, Chapter 4 - Central Station: j The prime contractor: -- 4A774 ,E Central Station Location: - p,Ji,vfr4 s 7&D -7c/9- 5/g Means of transmission of signals from the protected premise to the central station: Mculloh Multiplex One-Way Radio X Digital Alarm Communicator Two-Way Radio Others Means of transmission of alarms to the public fire service communications center: System Location: Organization Name / Phone Representative Name / Phone Installer SimplexGrinnell Bob Ciereck 858-633-9100 Supplier Simplex Grinnell Mark Walker 858-633-9100 Service Organization SimplexGrinnell Justine Guidos 858-633-9100 Page 1 of 4 NFPA Record of Completion (1996 ed.) Location of (As-Built) Drawings: Location of Owners Manuals: Same Location of Test Reports: A contract, dated , for test and inspection in accordance with NFPA standard(s) No(s), dated , is in effect. 2. Record of System Installation (Fill out after installation is complete and wiring checked for opens,shorts,ground faults and improper branching but prior to conducting operational acceptance tests.) Frequency This system has been installed in accordance with the NFPA standards as shown below,was inspected by SimplexGrinnell on ,includes the devices shown below and has been in service since NFPA 72, Chapters 1 3 4 5 6 7 (Circle all that apply) NFPA 70, National Electric Code ,Article 760 Manufacturer's Instructions Other ( Specify) 4 Signed: (CQ__7.. Date: Organization: / SimplexGrinnell Upon completion of the system(s)--satisfactory test(s) witnessed (if required by the authority h Record of System Operation All operational features and functions of this system were tested by SimplexGrinnell Date: and found to be operating properly in accordance with requirements of: NFPA 72, Chapters 1 3 4 5 6 7 (Circle all that apply) NFPA 70, National Electric Code ,Article 760 Manufacturer's Instructions Other ( Specify) Signed: - Date: Organization: SimplexGrinnell 4. Alarm Initiating Devices and circuits (Use blanks to indicate quantity of devices.) Manual IManual Stations x Noncoded,Activating Transmitters _Combination Manual Fire Alarm and Guard's Tour Coded Stations. Automatic Coded Coverage: Complete ..5 Smoke Detectors j Duct Detectors - Heat Detectors _Sprinkler Waterfiow Switches Other(list):____________________________ Partial Ion - Ion FT - Transmitters Photo Photo RR FTIRR Noncoded,Activating RC Coded 5. Supervisory Signal Initiating Devises and Circuits (Use blanks to indicate quantity of devices.) Guard's Tour Coded Stations Noncoded Stations Activating Transmitters C) Compulsory Guard Tour System Comprised of Transmitter Stations and Intermediate Note: Combination devices recorded under 4(b) and 5(a). Page 2 of 4 NFPA Record of Completion Sprinkler System 0 Coded Valve Supervisory Signaling Attachments Valve Supervisory Switches Activating Building Temperature Points j Site Water Temperature Points Site Water Supply Level Points Electric Fire Pump: jo Fire Pump Power z Fire Pump Running % Phase Reversal Engine Driven Fire Pump: Selector in Auto Position Engine or Control Panel Trouble standard Fire Pump Running Engine Driven Generator: k) Selector in Auto Position I) .0 Control Panel Trouble Transfer Switches 0 Engine Running Other Supervisory Function(s) (Specify) Transmitters Upon completion of the system(s) satisfactory test(s) witnessed (if required by the authority h Alarm Notification Appliances and Circuits Quantity of indicating appliance circuits connected to the system: Types and quantities of alarm indicating appliances installed: Bells Inch Speakers / 2— Horns Chimes Other: /— Visual Signals Type: Xenon with audible w/o audible Local Annunciator Admin Lobby Signaling Line Circuits: Quantity and Style (See NFPA 72, Table 3-6) of signaling line circuits connected to the system. Quantity: Style: V System Power Supplies Primary (Main): Nominal Voltage: I20VAC Current Rating: Overcurrent Protection: Type: Circuit Breaker Current Rating: Location: Secondary (Standby): X Storage Batteries Amp-Hour Rating Calculated capacity to drive system, in hours: X 24 60 Engine driven generator dedicated to fire alarm system: N/A Location of fuel storage: Emergency/Standby System used as backup to Primary Power Supply, instead of useing a secondary Power supply: Emergency System described in NFPA 70, Article 700 Legally Required Standby System described in NFPA 70, Article 701 Optional Standby System described in NFPA 70, Article 702, which also meets the performance requirements of Article 700 or 701 Page 3 of 4 NFPA Record of Completion System Software Operating System Software Revision Level(s): Application Software Revision Level(s): Revision Completed by: (name) (firm) 10. Comments: (signed ) for Central Station or Alarm Service Company (title) (date) Frequency of routine tests and inspections, if other than in accordance with the referenced NFPA standard NOT IN CONTRACT System deviations from the referenced NFPA standard(s) are: NONE (signed) for Central Station or Alarm Service Company (title) (date) Upon completion of thesystem(s) satisfactory test(s) witnessed (if required by the authority having jurisdiction) (signed) representative of the authority having jurisdiction (title) (date) Page 4of4