No preview available
HomeMy WebLinkAbout5620 PASEO DEL NORTE; 127C; FPC2019-0115; PermitPERMIT REPORT ((7city of Carlsbad CARLSBAD, CA 92008-4466 Work Class: Fire Sprinklers Track #: Lot #: Project #: Plan #: Construction Type: Orig. Plan Check#: Plan Check#: Permit No: FPC2019-0115 Status: Closed - Finaled Applied: 05/21/2019 Issued: 05/29/2019 Finaled Close Out: 09/26/2019 Inspector: Final Inspection: Print Date: 01/05/2021 Job Address: 5620 PASEO DEL NORTE, # 127C, Permit Type: FIRE-Construction Commercial Parcel #: 2110222202 Valuation: $47,626.24 Occupancy Group: #of Dwelling Units: Bedrooms: Bathrooms: Project Title: Description: JERSEY MIKES SUBS- SPRINKLER TI (27 HEADS) Applicant: FPContractor: JOHNSON CONTROL FIRE PROTECTION JOHNSON CONTROLS FIRE PROTECTION LP MARCUS ENGLISH P0 BOX 3042 3568 RUFFIN RD BOCA RATON, FL 33431-0942 SAN DIEGO, CA 92123-2597 (561) 341-7780 - (858) 633-9125 FEE AMOUNT FIRE NFPA 13 or 13R System 7 - 100 heads $553.00 Total Fees: $553.00 Total Payments To Date: $553.00 Balance Due: $0.00 Fire Department Page 1 of 1 1635 Faraday Avenue, Carlsbad CA 92008-7314 1760-602-4665 760-602-8561 f I www.carlsbadca.gov FPC20I9-01 15 5620 PASEO DEL NORTE #127C JERSEY MIKES SUBS- SPRINKLER TI (27 HEADS) 2110222202 5/21/2019 Series RFII - 56 K-factor FPC20I9-01 15 "Royal Flush II" Concealed rm im,nir Quick & Standard Response, Standard Coverage General Description The TYCO Series RFII 5.6 K-factor, "Royal Flush II" Concealed Pendent Sprinklers Quick Response (3-mm bulb) and Standard Response (5-mm bulb), are decorative sprinklers fea- turing a flat cover plate designed to conceal the sprinkler. These sprinklers are optimal for architecturally sensi- tive areas such as hotel lobbies, office buildings, churches, and restaurants. Each sprinkler includes a Cover Plate! Retainer Assembly and a Sprinkler! Support Cup Assembly. The separa- ble, two-piece assembly design pro- vides the following benefits: Allows installation of the sprinklers and pressure testing of the fire pro- tection system prior to installation of a suspended ceiling or application of the finish coating to a fixed ceiling. Permits the removal of suspended ceiling panels for access to building service equipment without having to first shut down the fire protection system and remove sprinklers. Provides for 1/2 in. (12,7 mm) of ver- tical adjustment to allow a measure of flexibility in determining the length of fixed piping to cut for the sprinkler drops. IMPORTANT Refer to Technical Data Sheet TFP2300 for warnings pertaining to regulatory and health information. Always refer to Technical Data Sheet TFP700 for the "INSTALLER WARNING" that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and installation can permanently damage a sprinkler system or its compo- nents and cause the sprinkler to fail to operate in a fire situation or cause it to operate prematurely. Page 1 of 4 The Series RFII Sprinklers are shipped with a Disposable Protective Cap. The Protective Cap is temporarily removed during installation and replaced to help protect the sprinkler during ceiling installation or finish. The tip of the Pro- tective Cap can be used to mark the center of the ceiling hole into plaster board or ceiling tiles by gently pushing the ceiling product against the Pro- tective Cap. When ceiling installa- tion is complete, the Protective Cap is removed and the Cover Plate/Retainer Assembly is installed. As an option, the Series RFII Standard Response (5-mm bulb) "Royal Flush II" Concealed Pendent Sprinklers can be fitted with a silicone Air and Dust Seal. (Refer to Figure 5.) The Air and Dust Seal is intended for sensitive areas where it is desirable to prevent air and dust from the area above the ceiling to pass through the cover plate. EM The Series RFll Concealed Pendent Sprinklers described herein must be installed and maintained in compliance with this document and with the appli- cable standards of the NATIONAL FIRE PROTECTION ASSOCIATION (NFPA), in addition to the standards of any authorities having jurisdiction. Failure to do so may impair the performance of these devices. The owner is responsible for maintain- ing their fire protection system and devices in proper operating condition. The installing contractor or sprinkler manufacturer should be contacted with any questions. Sprinkler Identification Number (SIN) TY3531 - 3 mm bulb 1Y3551 - 5 mm bulb SEPTEMBER 2018 Technical Data Sprinkler Approvals Approvals apply only to the service conditions indicated in the Design Criteria section. TY3531 (3 mm Bulb) is UL Listed, C-UL Listed and NYC Approved (MEA 353- 01-E) as Quick Response. 1Y3531 (3 mm Bulb) is VdS Approved (Certificate No. G4090007). 1Y3531 (3 mm Bulb) is FM and LPCB Approved (Ref. No. 094a/10) as Standard Response. Note: FM and LPCB do not approve concealed sprinklers for quick response. TY3551 (5 mm Bulb) is UL Listed, C-UL Listed, FM Approved, LPCB Approved (Ref. No. 094a/9), and NYC Approved (MEA 353-01 -E) as Standard Response. Approvals for Air and Dust Seal UL and C-UL Listed for use with the RFII Standard Response Concealed Sprinkler (TY3551) Maximum Working Pressure Maximum 250 psi (17,3 bar) by UL, C-UL, and NYC Maximum 175 psi (12,1 bar) by FM, VdS, and LPCB Temperature Rating 155°F (68°C) Sprinkler with 139°F (59°C) Cover Plate 200°F (93°C) Sprinkler with 165°F (74°C) Cover Plate TFPI8I SPRINKLER/SUPPORT CUP ASSEMBLY THREAD INTO RETAINER SUPPORT WITH THREAD CUP UNTIL 0 0 '_- DIMPLES MOUNTING SURFACE IS U EJECTION FLUSH WITH Ii SPRING CEILING H / SOLDER ' -. COVER TABS (3) COVER PLATE/RETAINER PLATE ASSEMBLY FIGURE 1 MODEL RFII CONCEALED SPRINKLER ASSEMBLY TFPI8I Page 2 of 4 Discharge Coefficient K= 5.6 GPM/psi112 (80,6 LPM/bar112) Adjustment 1/2 inch (12,7 mm) Finishes See the Ordering Procedure section. Physical Characteristics Frame ............................Bronze Support Cup ...................Plated Steel Guide Pins..................Stainless Steel Deflector ..........................Bronze Compression Screw ..................Brass Bulb...............................Glass Cap .....................Bronze or Copper Sealing Assembly. . Beryllium Nickel w/TEFLON Cover Plate .........................Brass Retainer............................Brass Ejection Spring ..............Stainless Steel Design Criteria The TYCO Series RFII 5.6 K-factor, "Royal Flush Il" Concealed Pendent Sprinklers are intended for fire protec- tion systems designed in accordance with the standard installation rules recognized by the applicable Listing or Approval agency; for example, UL Listing is based on NFPA 13 and VdS Approval is based on the CEA 4001. For more information on LPCB and VdS Approvals, contact Johnson Controlss at the following office: Enschede, Netherlands Telephone: 31-53-428-4444 Fax: 31-53-428-3377 The Series RFII Concealed Pendent Sprinklers are only listed and approved with the Series RFll Concealed Cover Plates having a factory applied finish. Do not use the Series RFII in applica- tions where the air pressure above the ceiling is greater than that below. Down drafts through the Sprinkler/Support Cup Assembly can delay sprinkler operation in a fire situation. Operation When exposed to heat from a fire, the Cover Plate, normally soldered to the Retainer at three points, falls away to expose the Sprinkler/Support Cup Assembly. The Deflector - supported by the Guide Pins - then drops down to its operational position. The glass bulb contains a fluid that expands when exposed to heat. When the rated temperature is reached, the fluid expands sufficiently to shatter the glass bulb, activating the sprinkler and allowing water to flow. 1/2 NPT FRAME SUPPOR CUP WITF ROLL FOR'J THREAD GUIDE PINS (2) DEFLECTOR Installation The TYCO Series RFII 5.6 K-factor, "Royal Flush II" Concealed Pendent Sprinklers must be installed in accor- dance with this section. General Instructions Do not install any bulb-type sprinkler if the bulb is cracked or there is a loss of liquid from the bulb. With the sprin- kler held horizontally, a small air bubble should be present. The diameter of the air bubble is approximately 1/16 inch (1,6 mm) for the 155°F (68°C) and 3/32 inch (2,4 mm) for the 200°F (93°C) tem- perature ratings. A leak-tight 1/2 inch NPT sprinkler joint should be obtained by applying a minimum to maximum torque of 7 to 14 ft.-lbs. (9,5 to 19,0 Nm). Higher levels of torque can distort the sprinkler Inlet with consequent leakage or impairment of the sprinkler. EALING SEMBLY CAP BULB PRESSION )CREW LECTOR ROPPED POSITION) Do not attempt to compensate for insufficient adjustment in the Sprinkler by under- or over-tightening the Sprin- kler/Support Cup Assembly. Re-adjust the position of the sprinkler fitting to suit. Step 1. Install the sprinkler only in the pendent position with the center-line of the sprinkler perpendicular to the mounting surface. Step 2. Remove the Protective Cap. Step 3. With pipe thread sealant applied to the pipe threads, hand- tighten the sprinkler into the sprinkler fitting. Step 4. Wrench-tighten the sprinkler using only the RFII Sprinkler Wrench. (Refer to Figure 3.) Apply the RFII Sprinkler Wrench to the Sprinkler as shown in Figure 3. -\ I I I I V MANUFACTURER DEFLECTOR COVER PLATE PRESET GAP IN DROPPED RETAINER 3/32 (2,4 mm) POSITION ASSEMBLY COVER PLATE DIAMETER DIMENSION A 3/16 to 11/16 (4,8 to 17,5 mm) REFERENCE COVER PLATE - PROFILE DEPTH DIMENSION B 3-1/4 inches (82,6 mm) C: 2-3/8 to 2-5/8 inches (60,3 to 66,7 mm) 3/16 inches (4,8 mm) D: 1-3/4 to 2-1/4 inches (44,5 to 57,2 mm) FIGURE 2 SERIES CONCEALED SPRINKLER INSTALLATION DIMENSIONS TFPI8I Page 3 of 4 FACE OF SPRINKLER FITTING SPRINKLER SUPPORT CUP ASSEMBLY 1/2 (12,7 mm) THREADED D ADJUSTMENT FACE OF CEILING, RETAINING RING MOUNTING SURFACE CLEARANCE HOLE - DIAMETER DIMENSION Step 5. Replace the Protective Cap by pushing it upwards until it bottoms out against the Support Cup. (Refer to Figure 4.) The Protective Cap helps prevent damage to the Deflector and Arms during ceiling installation and/or finish. You can also use the Protective Cap to locate the center of the clear- ance hole by gently pushing the ceiling material up against the center point of the Protective Cap. LI1IL As long as the Protective Cap remains in place, the system is considered "Out of Service". Step 6. After the ceiling has been completed with the 2-1/2 in. (63,5 mm) diameter clearance hole and in prep- aration for installing the Cover Plate! Retainer Assembly, remove and discard the Protective Cap. Verify that the Deflector moves up and down freely. If the Sprinkler is damaged and the Deflector does not move up and down freely, replace the entire Sprinkler. Do not attempt to modify or repair a damaged sprinkler. Step 7. When installing an Air and Dust Seal, refer to Figure 5; otherwise, proceed to Step 8. To attach the Air and Dust Seal, verify the angle of the outside edge of the seal is oriented according to Figure 5. Start the edge of the Retainer in the grooved slot of the Air and Dust Seal and continue around the retainer until the entire Air and Dust Seal is engaged. TFPISI Page 4 of 4 Step 8. Screw on the Cover Plate! Retainer Assembly until the Retainer (shown in Figure 2) or the Air and Dust Seal (shown in Figure 5) contacts the ceiling. Do not continue to screw on the Cover Plate/Retainer Assembly so that it lifts a ceiling panel out of its normal position. If you cannot engage the Cover Plate/Retainer Assembly with the Support Cup or you cannot engage the Cover Plate/Retainer Assembly suf- ficiently to contact the ceiling, you must reposition the Sprinkler Fitting. Care and Maintenance The TYCO Series RFII 5.6 K-factor, "Royal Flush II" Concealed Pendent Sprinklers must be maintained and serviced in accordance with this section. Before closing a fire protection system main control valve for maintenance work on the fire protection system that it controls, obtain permission to shut down the affected fire protection system from the proper authorities and notify all personnel who may be affected by this action. Absence of the Cover Plate/Retainer Assembly can delay sprinkler opera- tion in a fire situation. When properly installed, there is a nominal 3/32 in. (2,4 mm) air gap between the lip of the Cover Plate and the ceiling, as shown in Figure 2. This air gap is necessary for proper operation of the sprinkler. If the ceiling requires repainting after sprinkler installation, ensure that the new paint does not seal off any of the air gap. Do not pull the Cover Plate relative to the Enclosure. Separation may result. Sprinklers which are found to be leaking or exhibiting visible signs of corrosion must be replaced. Automatic sprinklers must never be painted, plated, coated, or other- wise altered after leaving the factory. Modified sprinklers must be replaced. Sprinklers that have been exposed to corrosive products of combustion, but have not operated, should be replaced if they cannot be completely cleaned by wiping the sprinkler with a cloth or by brushing it with a soft bristle brush. Care must be exercised to avoid damage to the sprinklers - before, during, and after installation. Sprin- klers damaged by dropping, striking, wrench twist/slippage, or the like, must• be replaced. Also, replace any sprin- kler that has a cracked bulb or that has lost liquid from its bulb. (Ref. Installa- tion Section.) Exercise care to avoid damage to sprin- klers before, during, and after instal- lation. Replace sprinklers damaged by dropping, striking, wrench twist- ing, wrench slipping, or the like. Also, replace any sprinkler that has a cracked bulb or that has lost liquid from its bulb. (Refer to the Installation section.) If you must remove a sprinkler, do not reinstall it or a replacement without reinstalling the Cover Plate/Retainer Assembly. If a Cover Plate/Retainer Assembly becomes dislodged during service, replace it immediately. The owner is responsible for the inspection, testing, and maintenance of their fire protection system and devices in compliance with this document, as well as with the applicable standards of the NATIONAL FIRE PROTECTION ASSOCIATION, for example, NFPA 25, in addition to the standards of any other authorities having jurisdiction. Contact the installing contractor or sprinkler manufacturer regarding any questions. Automatic sprinkler systems should be inspected, tested, and maintained by a qualified Inspection Service in accor- dance with local requirements and/or national code. Limited Warranty For warranty terms and conditions, visit www.tyco-fire.com. Ordering Procedure Contact your local distributor for availability. When placing an order, indicate the full product name. Sprinkler/Support Cup Assembly Specify: Series RFII (specify SIN), K=5.6, "Royal Flush II" Pendent Sprin- klers (specify) temperature rating, P/N* (specify): 155°F (68°C 200°F (93°C TY3531 51-792-1-155 51-792-1-200 TY3551 51-790-1-155 51-790-1-200 Use Suffix "I" for ISO 7-1 connection; for example, 51-792-1-155-I Separately Ordered Cover Plate/ Retainer Assembly: Specify: (temperature rating from below) Series RFII Concealed Cover Plate with (finish), P/N (specify). 139°F (59°C)(a) 165°F (74°C)(b) Grey White (RAL9002) .... 56-792-0-135 56-792-0-165 Brass..........56-792-1-135 56-792-1-165 Pure White (c) (RAL9010) .... 56-792-3-135 56-792-3-165 Signal White (RAL9003).... 56-792-4-135 56-792-4-165 Jet Black (RAL9005).... 56-792-6-135 59-792-6-165 Brushed Chrome........56-792-8-135 56-792-8-165 Chrome........56-792-9-135 56-792-9-165 Custom ........56-792-X-135 56-792-X-165 For use with 155°F (68°C) sprinklers. For use with 200°F (93°C) sprinklers. Eastern Hemisphere sales only. Sprinkler Wrench Specify: RFII Sprinkler Wrench, P/N 56-000-1-075 Air and Dust Seal Specify: Air and Dust Seal, P/N 56-908-1-001 1400 Pennbrook Parkway, Lansdale, PA 194461 Telephone +1-215-362-0700 02018 Johnson Controls. All rights reserved. All specifications and other Information shown were current as of document revision dale and are subject to change without notice. Johnson /1 i)11 ' ' NATIONAL FIRE PROTECTION ASSOCIATION and NFPAa,o registered tradon,a,ke at National Fire PnvvAvn Association; TEFLON Is registered trademark at DuPont Controls Worldwide I t11,ca Contacts www.tyco-fire.com Series TY-FRB, 56 K-factor Upright, Pendent, and Recessed Pendent Sprinklers Quick Response, Standard Coverage General Description The TYCO Series TY-FRB, 5.6 K-factor, Upright (TY313) and Pendent (TY323) Sprinklers described in this data sheet are quick response, standard coverage, decorative 3 mm glass bulb-type spray sprinklers designed for use in light or ordinary hazard, commercial occupan- cies such as banks, hotels, and shop- ping malls. The recessed version of the Series TY-FRB Pendent Sprinkler, where applicable, is intended for use in areas with a finished ceiling. This recessed pendent sprinkler uses one of the following: A two-piece Style 15 Recessed Escutcheon with recessed adjust- ment up to 5/8 in. (15,9 mm) from the flush pendent position. A two-piece Style 20 Recessed Escutcheon with recessed adjust- ment up to 1/2 in. (12,7 mm) from the flush pendent position. The adjustment provided by the Recessed Escutcheon reduces the accuracy to which the fixed pipe drops to the sprinklers must be cut. Intermediate level versions of Series TY-FRB Sprinklers are described in Technical Data Sheet TFP357. Sprin- kler guards and shields are described in Technical Data Sheet TFP780. IMPORTANT Refer to Technical Data Sheet TFP2300 for warnings pertaining to regulatory and health information. Always refer to Technical Data Sheet TFP700 for the "INSTALLER WARNING" that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and installation can permanently damage a sprinkler system or its compo- nents and cause the sprinkler to fail to operate in a fire situation or cause it to operate prematurely. Page 1 of 4 NOTICE The TYCO Series TY-FRB Sprinklers described herein must be installed and maintained in compliance with this document, as well as with the applicable standards of the National Fire Protection Association, in addition to the standards of any other authori- ties having jurisdiction. Failure to do so may impair the performance of these devices. The owner is responsible for main- taining their fire protection system and devices in proper operating con- dition. Contact the installing contrac- tor or product manufacturer with any questions. Sprinkler Identification Number (SIN) TY313.... Upright 5.61K, 1/2 in. NPT TY323. . . .Pendent 5.61K, 1/2 in. NPT Technical Data Approvals Refer to Table A Maximum Working Pressure 175 psi (12.1 bar) 250 psi (17.2 bar)* The maximum working pressure of 250 psi (17.2 bar) only applies to the listing by Underwriters Laborato- ries, Inc. (UL). Discharge Coefficient K=5.6 GPM/p51½ (80,6 LPM/bar½) Temperature Rating Refer to Table A Finishes Sprinkler: Refer to Table B Recessed Escutcheon: White Coated, Black Coated, Chrome Plated, or Brass Plated Physical Characteristics Frame ............................Bronze Button ......................Brass/Copper Sealing Assembly ... Stainless Steel w/TEFLON Bulb...............................Glass Compression Screw .................Bronze Deflector ..........................Bronze AUGUST 2018 Operation The glass bulb contains a fluid which expands when exposed to heat. When the rated temperature is reached, the fluid expands sufficiently to shatter the glass bulb, allowing the sprinkler to activate and water to flow. Design Criteria The TYCO Series TY-FRB, 5.6 K-factor, Upright (TY313) and Pendent (TY323) Sprinklers are intended for fire protec- tion systems designed in accordance with the standard installation rules recognized by the applicable Listing or Approval agency (such as, UL Listing is based on the requirements of NFPA 13, and FM Approval is based on the requirements of FM's Loss Prevention Data Sheets). Only the Style 15 or Style 20 Recessed Escutcheon is to be used for recessed pendent installations. TFPI72 TFPI72 Page 2 of 4 Components: 1 - Frame 2 - Button 3 - Sealing Assembly * Temperature rating is ** Pipe thread connections per ISO 7-1 4 - Bulb indicated on Deflector. can be provided on special request. 5 - Compression Screw ESCUTCHEON PLATE 1/2 7/16 (11,1 mm) 6 - Deflector * DEFLECTOR* SEATING SURFACE NPT** NOMINAL MAKE-IN STYLE 15 or 20 RECESSED ESCUTCHEON 7/16' _______ I (111mm) _____ 2' (50,8 mm) ______ I NOMINAL (34,9 mm) FLATS MAKE-IN _____ 13 2" (50,8 mm) WRENCH 1/2' NPT** DEFLECTOR* 2-7/8" (73,0 mm) DIA. CROSS SECTION UPRIGHT PENDENT RECESSED PENDENT FIGURE 1 SERIES TY-FRB UPRIGHT (TY313) AND PENDENT (TY323) SPRINKLERS 5.6 K-FACTOR, 1/2 INCH NPT, QUICK RESPONSE Installation The TYCO Series TY-FRB, 5.6 K-factor, Upright (TY313) and Pendent (1Y323) Sprinklers must be installed in accor- dance with this section. General Instructions Do not install any bulb-type sprin- kler if the bulb is cracked or there is a loss of liquid from the bulb. With the sprinkler held horizontally, a small air bubble should be present. The diam- eter of the air bubble is approximately 1/16 in. (1,6 mm) for the 135°F(57°C)and 3/32 in. (2,4 mm) for the 286°F (141°C) temperature ratings. A leak-tight 1/2 in. NPT sprinkler joint should be obtained by applying a minimum to maximum torque of 7 to 14 lb-ft (9,5 to 19,0 N•m). Higher levels of torque can distort the sprinkler Inlet with consequent leakage or impairment of the sprinkler. Do not attempt to compensate for insufficient adjustment in the Escutch- eon Plate by under- or over-tightening the sprinkler. Re-adjust the position of the sprinkler fitting to suit. Upright and Pendent Sprinklers The Series TY-FRB Upright and Pendent Sprinklers must be installed in accordance with the following instructions. Step 1. Install Pendent sprinklers in the pendent position. Install upright sprin- klers in the upright position. Step 2. With pipe-thread sealant applied to the pipe threads, hand- tighten the sprinkler into the sprinkler fitting. Step 3. Tighten the sprinkler into the sprinkler fitting using only the W-Type 6 Sprinkler Wrench (Figure 2). With ref- erence to Figure 1, apply the W-Type 6 Sprinkler Wrench to the wrench flats. Torque sprinklers 7 to 14 lb-ft (9,5 to 19,0 Nm). Recessed Pendent Sprinklers The Series TY-FRB Recessed Pendent Sprinklers must be installed in accor- dance with the following instructions. Step A. After installing the Style 15 or Style 20 Mounting Plate over the sprinkler threads, and with pipe-thread sealant applied to the pipe threads, hand-tighten the sprinkler into the sprinkler fitting. Step B. Tighten the sprinkler into the sprinkler fitting using only the W-Type 7 Recessed Sprinkler Wrench (Figure 3). With reference to Figure 1, apply the W-Type 7 Recessed Sprinkler Wrench to the sprinkler wrench flats. Torque sprinklers 7 to 14 lb-ft (9,5 to 19,0 N.m). Step C. After ceiling installation and finishing, slide on the Style 15 or Style 20 Closure over the Series TY-FRB Sprinkler and push the Closure over the Mounting Plate until its flange comes in contact with the ceiling. / WRENCH RECESS / (USE ONLY FIGURE 2 W-TYPE 6 SPRINKLER WRENCH WRENCH RECESS PUSH WRENCH IN TO ENSURE ENGAGEMENT WITH SPRINKLER WRENCHING AREA FIGURE 3 W-TYPE 7 RECESSED SPRINKLER WRENCH TFPI72 - -- Page 3of4 Care and Maintenance The TYCO Series TY-FRB, 5.6 K-factor, Upright (TY313) and Pendent (TY323) Sprinklers must be maintained and ser- viced in accordance with this section. Before closing a fire protection system main control valve for maintenance work on the fire protection system that it controls, obtain permission to shut down the affected fire protection systems from the proper authorities and notify all personnel who may be affected by this action. Absence of the outer piece of an escutcheon, which is used to cover a clearance hole, can delay sprinkler operation in a fire situation. The owner must assure that the sprin- klers are not used for hanging any objects and that the sprinklers are only cleaned by means of gently dusting with a feather duster; otherwise, non- operation in the event of a fire or inad- vertent operation may result. Sprinklers which are found to be leaking or exhibiting visible signs of corrosion must be replaced. Automatic sprinklers must never be painted, plated, coated, or other- wise altered after leaving the factory. Modified sprinklers must be replaced. Sprinklers that have been exposed to corrosive products of combustion, but have not operated, should be replaced if they cannot be completely cleaned by wiping the sprinkler with a cloth or by brushing it with a soft bristle brush. Care must be exercised to avoid damage to the sprinklers before, during, and after installation. Sprin- klers damaged by dropping, striking, wrench twist/slippage, or the like, must be replaced. Also, replace any sprin- kler that has a cracked bulb or that has lost liquid from its bulb. (Ref. Installa- tion Section.) The owner is responsible for the inspection, testing, and maintenance of their fire protection system and devices in compliance with this document, as well as with the applicable standards of the National Fire Protection Asso- ciation (e.g., NFPA 25), in addition to the standards of any other authorities having jurisdiction. Contact the install- ing contractor or product manufacturer with any questions. Automatic sprinkler systems are rec- ommended to be inspected, tested, and maintained by a qualified Inspec- tion Service in accordance with local requirements and/or national codes. Limited Warranty For warranty terms and conditions, visit www.tyco-fire.com. Ordering Procedure Contact your local distributor for avail- ability. When placing an order, indicate the full product name and Part Number (P/N). Sprinkler Assemblies with NPT Thread Connections Specify: Series TY-FRB Upright or Pendent (specify) Sprinkler, SIN (specify), K=5.6, Quick Response, (specify) temperature rating, (specify) finish, P/N (specify, refer to Table A). Recessed Escutcheon Specify: Style 15 Recessed Escutch- eon with (specify*) finish, P/N (specify*) Specify: Style 20 Recessed Escutch- eon with (specify*) finish, P/N (specify*) * Refer to Technical Data Sheet TFP770 Sprinkler Wrench Specify: W-Type 6 Sprinkler Wrench, P/N 56-000-6-387 Specify: W-Type 7 Sprinkler Wrench, P/N 56-850-4-001 2-7/8 DIA. (73,0 mm) 2-1/4 DIA. FACE OF (57,2 mm) SPRINKLER FITTING 5/8 (15,9 mm) FLUSH 3/85/0 MOUNTING 1/8" SURFACE (3,2 mm) CLOSURE SERIES MOUNTING 1-3/8 (34,9 mm) 1YFRB PLATE 3/4 (19,1 mm) FIGURE 4 SERIES TY-FRB RECESSED PENDENT SPRINKLER ASSEMBLY (TY323) WITH TWO PIECE 5/8 INCH TOTAL ADJUSTMENT STYLE 15 RECESSED ESCUTCHEON - 2-7/8 DIA. (73,0 mm) FACE OF SPRINKLER - 2-1/4" DIA. FITTING (57,2 mm) 5/16±1/4 1/2" (12,7 mm) (7,9±6,4 mm) FLUSH _ $ MOUNTING L(312 SURFACE CLOSURE SERIES MOUNTING 1-3/8"(34,9mm) TY-FRB PLATE 7/8" (22,2 mm) FIGURE 5 SERIES TY-FRB RECESSED PENDENT SPRINKLER ASSEMBLY (TY323) WITH TWO PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 20 RECESSED ESCUTCHEON TFPI72 Page 4 of 4 SPRINKLER FINISH (See Note 7) K FACTOR TYPE TEMPERATURE BULB LIQUID COLOR NATURAL BRASS I CHROME PLATED 1 POLYESTERv 135-F (57-C) Orange UPRIGHT (TY313) 155°F (68°C) Red 175°F (79°C) Yellow and 1, 2, 3, 4, 5, 6 PENDENT (TY323) 200°F (93°C) Green 286°F (141°C) Blue 5.6 1/2 in. NPT ________________ 135°F (57°C) Orange RECESSED PENDENT (TY323) Figures 4a and 5b 1,2,3,4 155°F (68°C) Red 175°F (79°C) Yellow 200°F (93°C) Green Notes: Listed by Underwriters Laboratories, Inc., (UL) as Quick Response Sprinklers. Listed by Underwriters Laboratories, Inc., for use in Canada (C-UL) as Quick Response Sprinklers. Approved by Factory Mutual Research Corporation (FM) as Quick Response Sprinklers. Approved by the City of New York under MEA 354-01-E. VdS Approved (For details, contact Johnson Controls, Enschede, Netherlands, Tel. 31-53-428-4444/Fax 31-54-428-3377.) Approved by the Loss Prevention Certification Board (LPCB Ref. No. 094a/06) as Quick Response Sprinklers. Where Polyester Coated Sprinklers are noted to be UL and C-UL Listed, the sprinklers are UL and C-UL Listed as Corrosion-Resistant Sprinklers. Installed with Style 15 (1/2 in. NPT) 5/8 in. Total Adjustment Recessed Escutcheon, as applicable. Installed with Style 20 (1/2 in. NPT) 1/2 in. Total Adjustment Recessed Escutcheon, as applicable. C. Frame and Deflector only. Listings and approvals apply to color (Special Order). TABLE A LABORATORY LISTINGS AND APPROVALS FOR 5.6 K-FACTOR SPRINKLERS P/Na 77—XXX—X—)OO( CHROME PLATED Notes: a. Eastern Hemisphere sales only TABLE B SERIES TY-FRB UPRIGHT AND PENDENT SPRINKLERS PART NUMBER SELECTION I SPRINKLER FINISH 1 NATURAL BRASS PURE WHITE (RAL9010)a POLYESTER SIGNAL WHITE (RAL9003) - POLYESTER JET BLACK (RAL9005) POLYESTER TEMPERATURE RATINGS 135 135-F (57-C) 155 1 155°F(68°C) 175 I 175°F (79°C) 200 I 200°F (93°C) 286 1 286°F(141°C) SIN 370 I 5.6K UPRIGHT (1/2 in.NPT) I TY313 371 5.6K PENDENT (1/2 in.NPT) TY323 Notes: a. Use suffix '1" for ISO 7-1 connection; for example, 77-370-4-175-I 1400 Pannbrook Parkway, Lansdale, PA 19446 I Telephone +1-215-362-0700 iil r 02018 Johnson Controls. All rights reserved. All specifications and ether Information shown were current as of document revision dote and are subjectte change without notice. Johnson '.',i Ø NATIONAL FIRE PROTECTION ASSOCIATION and NFPA are registered twdnmo,l,n SI National Fire Protection Association; TEFLON Is registered tradanrork at DuPed 0* FLUSH INTERMEDIATE EXTENDED RECESSED PLAIN BARREL Dry Type Standard Spray Pendent, Intermediate Level Pendent & Recessed Pendent V3605 STANDARD RESPONSE V3606 QUICK RESPONSE t SLEEVE AND SKIRT COVERAGE: The Model V36 Series Dry Type Pendent and Recessed Pendent Sprinklers have been redesigned utilizing stainless steel internal components. The V36 Dry Sprinkler is used in special applications such as freezing environments and conditions where sediment or foreign materials might accumulate in ordinary drop nipples. The Model V3606 and V3605 Intermediate Level Pendent sprinklers incorporate a water shield plate to prevent water from higher level sprinklers from interfering with normal operation. These intermedi- ate level sprinklers are designed for use in intermediate levels of rack storage or other open grate storage arrangements, where they may be exposed to upper level or ceiling level sprinklers. Available in either standard or quick response versions, the Model V36 Dry Type Pendent Sprinkler utilizes a frangible glass bulb. At the bulb's rated temperature, the sprinkler opens releasing the bulb seat assembly, causing the inner tube assembly to move, allowing the spring assembly to pivot along- side the inner tube. At this time, water flows through the sprinkler and is distributed by the deflector, in an approved discharge pattern. The heart of the Model V36 sprinkler's proven actuating assembly is a hermetically sealed frangible glass bulb that contains a precisely measured amount of fluid. When heat is absorbed, the liquid within the bulb expands increasing the internal pressure. At the prescribed temperature the internal pressure within the bulb exceeds the strength of the glass causing the glass to shatter. This results in water discharge which is distributed in an approved pattern. For coverage area and sprinkler placement, refer to NFPA 13 standards. JOB OWNER CONTRACTOR ENGINEER System No. Submitted By Spec Sect Para___________ Location Date Approved www.victaulic.com vIcTAULIc IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2009 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REV ...H JtauIicr 40.60.J FIRE PROTECTION PRODUCTS - AUTOMATIC SPRINKLERS 40.60 V36, K56 C® Pendent, Intermediate Level Pendent LISTED Dry Type Standard Spray II & Recessed Pendent V3605 STANDARD RESPONSE V3606 QUICK RESPONSE FLUSH SLEEVE AND PLAIN BARREL INTERMEDIATE EXTENDED RECESSED SKIRT TECHNICAL SPECIFICATIONS: Exaggerated for clarity Models: V3606 and V3605 Style: Pendent, Recessed Pendent or Intermediate Level Pendent Nominal Orifice Size: 1h'/13 mm Orifice Insert: Stainless steel per UNS S30300 K-Factor: 5.6 Imp./8.1 S.l.' Nominal Thread Size: 1' NPT/33.7 mm Max. Working Pressure: 175 psi/1200 kPa Factory Hydrostatic Test: 100% @ 500 psi/3450 kPa Mm. Operating Pressure: 7psi/48kPa Temperature Rating: See chart on page 2 MATERIAL SPECIFICATIONS Deflector: Brass per UNS 022000 or Stainless Steel per UNS S30400 Bulb: Glass with glycerin solution. Bulb Nominal Diameter: Standard: 5.0 mm Quick Response: 3.0 mm Split Spacer: Stainless steel per UNS S30300 Load Screw: Brass per UNS 036000 Pip Cap: Stainless steel per UNS S30300 Spring Seal Assembly: Teflon* coated Beryllium nickel alloy and stainless steel per UNS S30300 Frame: Die cast brass Outer Tube: Galvanized steel pipe Inner Tube: Stainless steel per UNS S30400 Escutcheon/Plate: 1010 - 1018 mild steel and stainless steel Torsion Spring: SST Wire ACCESSORIES Installation Wrench: Model V36 Open End and Recessed Wrenches fit all V36 Series frames. Sprinkler Finishes: Plain brass Chrome plated White painted t A Flat black painted t A Custom painted t A Wax Proprietary Nickel Teflon* Coated A For cabinets and other accessories refer to separate sheet. A For K-Factor when pressure is measured in Bar, multiply S.I. units by 10.0. * Teflon is a registered trademark of Dupont Co. t Not available on the Intermediate Level Style Pendent. A Models V3606/V3605 are UL Listed for cor- rosion resistance in all configurations NOTE: Weather resistant escutcheon available upon request. www.vlctaulic.com VICTAULIC Is A REGISTERED TRADEMARK OF vrcTAuuC COMPANY. 02009 vICTAULIc COMPANY. ALL RIGHTS RESERVED. 40.60 .2 \4tauliIII REVH FIRE PROTECTION PRODUCTS AUTOMATIC SPRINKLERS 40.60 V36, K56 C® LISTED Dry Type Standard Spray Pendent, Intermediate Level Pendent & Recessed Pendent 7f 4 V3605 STANDARD RESPONSE V3606 QUICK RESPONSE FLUSH SLEEVE AND PLAIN BARREL INTERMEDIATE EXTENDED RECESSED SKIRT APPROVALS/LISTINGS l Listings and approval as of printing. A For K-Factor when pressure is measured in Bar, multiply S.I. units by 10. *Listed for all hazards. t Approved for V3605 and V3606 dry sprinklers up to 48 length. RATINGS All glass bulbs are rated for temoeratures from -67°F/-55°C to those shown in table below. Sprinkler Temperature Nominal Classitication Ordinary Temperature Temperature Rating 135 57 - F/ C Maximum Ambient Temperature Allowed EIS 38 Glass Bulb Color Orange Ordinary 155 68 100 38 - Red r Intermediate i 200 93 150 65 CTi*Yi Intermediate 286 141 225 107 Blue www.victaulic.com VICTAULIC IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2009 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REVH \4taulic 40.60 .3 FIRE PROTECTION PRODUCTS - AUTOMATIC SPRINKLERS 40.60 V36, K56 Dry Type Standard Spray Pendent, Intermediate Level Pendent & Recessed Pendent V3605 STANDARD RESPONSE V3606 QUICK RESPONSE ORDERING INFORMATION I LISTED ft Allft FLUSH SLEEVE AND PLAIN BARREL INTERMEDIATE EXTENDED RECESSED SKIRT Please specify the following when ordering: Sprinkler Model Number ------------------------------------------ Style Temperature Rating K-Factor: Thread Size Quantity Sprinkler Finish Escutcheon Finish Wrench Model Number AVAILABLE WRENCHES Model V36 Open End and Recessed Wrenches fit all V36 Series frames. fe00 www.victaulic.com .,4tauiice VICTAULIC IS REGISTERED TRADEMARK OF VlcTAUUc COMPANY. 2009 vIcTAULIC COMPANY. ALL RIGHTS RESERVED. 40.604 REV FIRE PROTECTION PRODUCTS AUTOMATIC SPRINKLERS V36, K56 Dry Type Standard Spray Pendent, Intermediate Level Pendent & Recessed Pendent V3605 STANDARD RESPONSE V3606 QUICK RESPONSE tL FLUSH .1 SLEEVE AND PLAIN BARREL SKIRT FAI LISTED INTERMEDIATE EXTENDED RECESSED WARNING WARNING Always read and understand installation, care, and maintenance instructions, supplied with each box of sprinklers, before proceeding with installation of any sprinklers. Always wear safety glasses and foot protection. Depressurize and drain the piping system before attempting to install, remove, or adjust any Victaulic piping products. Installation rules, especially those governing obstruction, must be strictly followed. Painting, plating, or any re-coating of sprinklers (other than that sup- plied by Victaulic) is not allowed. O Failure to follow these instructions could result in serious personal injury and/or property damage. The owner is responsible for maintaining the fire protection system and devices in proper operating condition. For minimum maintenance and inspection requirements, refer to the current National Fire Protection Association pamphlet that describes care and maintenance of sprinkler systems. In addition, the authority having jurisdiction may have addi- tional maintenance, testing, and inspection requirements that must be Olt followed. If you need additional copies of this publication, or if you have any 610 questions about the safe installation of this product, contact Victaulic World Headquarters: P.O. Box 31, Easton, Pennsylvania 18044-0031 USA, Telephone: 001-610-559-3300. www.victaulic.com \JtauIac VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2009 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REV.H 40.60_5 FIRE PROTECTION PRODUCTS - AUTOMATIC SPRINKLERS 40.60 V36, K5.6 JUSTED Dry Type Standard Spray Pendent, Intermediate Level Pendent & Recessed Pendent V3605 STANDARD RESPONSE '13606 QUICK RESPONSE FLUSH SLEEVE AND PLAIN BARREL INTERMEDIATE EXTENDED RECESSED SKIRT DIMENSIONS NOTE: The "A" dimension of a dry sprinkler, which extends into a freezer from a wet piping system, must take into account the wall or ceiling thickness of the freezer. See IMPORTANT INSTALLATION INFORMATION later in this document. Tee with same cutlet size as sprinkler thread size. See important Installation - - NPT Information later in this document fl-------fl , -- ___________________ I Tee with same cutlet size as sprinkler thread size. See 'Important Installatior Information',later in this document 1 NPT ' 'A' (Mm. 1W) 1½" Mm.Dia in ceiling (Mm Two 1V) n. Ho)ein Hole 1IW Mm. Din. Ceiling r 3" Din ece Escutcheon ia. W Mm. Flush --, Sleeve and Skirt Tee with tame outlet size Tee with same outlet size as sprinkler thread size. as sprinkler thread size. I I I See'lmpoo ant Installation See'lmportant Installation Information",later in this )nformatiori later in this document 1 document PT 1"NPT (Min. (Mm. 1'/u') V7TI T A. 1 3' Dia.—. Intermediate Level Pendent Plain Barrel 11 Tee with same outlet size fl fl Tee with same outlet size / ' ' as sprinkler thread size. ' ,,, I as sprinkler thread size. See'lmportant Installation Installation _______________ InformationI later in ____________ Information, later in this 1" NPT this document 1' NPI document 'A' 1½"Min.Dia. (Mm. t 'A') Hole in Ceiling (Mm Collar ie'°ttm -- tHol 2" Mm Din. 3~' Mm. e in Ceiling Two Piece 5" Max. Escutcheon Ceiling Cup Max. Extended ________ Recessed www.victaulic.com \,4'tauIiC' VICTAULIC Is A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2009 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 40.60 ,6 REV FIRE PROTECTION PRODUCTS — AUTOMATIC SPRINKLERS . 40.60 V369 K5.6 LISTED Dry Type Standard Spray Mak Pendent, Intermediate Level Pendent & Recessed Pendent A1111111111111111 11111111111111h MM V3605 STANDARD RESPONSE V3606 QUICK RESPONSE FLUSH SLEEVE AND PLAIN BARREL INTERMEDIATE EXTENDED RECESSED SKIRT DISTRIBUTION PATTERNS MODELS V3606, V3605 PENDENT, RECESSED PENDENT & INTERMEDIATE LEVEL PENDENT DISTRIBUTION PATTERNS - TRAJECTORY 8' 2.4 m 6' 1.8 m 4' 1.2 m 2' 0.6 m 0 2' 4' 6' 8' 10' 12' 14' 0.6 m 1.2 m 1.8 m 2.4 m 3.0 m 3.7 m 4.3 m 7ps1 —u.—. 15 psi 30ps1 48 kPa 103 kPa 207 kPa NOTES: 1 Data shown is approximate and can vary due to differences in installation. 2 These graphs illustrate approximate trajectories, floor-wetting, and wall-wetting patterns for these specific Victaulic FireLock automatic sprinklers. They are provided as information for guidance in avoiding obstructions to sprinklers and should not be used as minimum sprin- kler spacing rules for installation. Refer to the appropriate NFPA National Fire Code and the Authority Having Jurisdiction for specific information regarding obstructions, spacing limitations and area of coverage requirements. Failure to follow these guidelines could adversely affect the performance of the sprinkler and will void all Listings, Approvals and Warranties. 3 All patterns are symmetrical to the centerline of the waterway. www.victaulic.com \/(tauIic. vicTAuLic IS REGISTERED TRADEMARK OF vIcTAuLIc COMPANY. 2009 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REV..H 40.607 End Seal CExposed Minimum Barrel Lenqth (Refer to Table) Diameter of hole is dependent upon the type of escutcheon selected. Space must be sealed to prevent condensation from forming, per NFPA requirements. HEATED SPACE .A. See Note COLD SPACE Exaggerated foraanty TYPICAL SLEEVE AND SKIRT CONFIGURATION FOR EXAMPLE ONLY FIRE PROTECTION PRODUCTS — AUTOMATIC SPRINKLERS i 40.60 V36, K5.6 USTED Dry Type Standard Spray . Pendent, Intermediate Level Pendent & Recessed Pendent V3605 STANDARD RESPONSE V3606 QUICK RESPONSE JL 4 IY1 FLUSH SLEEVE AND PLAIN BARREL INTERMEDIATE EXTENDED RECESSED SKIRT IMPORTANT INSTALLATION INFORMATION For detailed installation instructions, see publication 1-40. No. 1 Victaulic Model V36 Series Dry sprinklers should be installed in accordance with NFPA 13. These sprinklers are to be installed using a pipe wrench applied to the outer tube. When this is not possible, the proper sprinkler wrench may be used with extreme care for lengths up to approximately 18. Excessive force may distort the frame thus destroying the unit. No. 2 Dry sprinklers MUST be installed only into the outlet of a cast or malleable iron tee. No. 3 DO NOT install dry sprinklers into any couplings or threaded elbows. In addition, DO NOT install dry sprinklers into any fitting that interferes with thread penetration. NOTE: The end seal of the dry sprinkler MUST NOT bottom out in the fitting. NOTE: The 'A" dimension of a dry sprinkler, which extends into a freezer from a wet piping system, must take into account the wall or ceiling thickness of the freezer. The minimum length of the dry sprinkler should not be less than the lengths specified in the following table, plus the thickness of the freezer's wall or ceiling ("A" = "C" + "D"). Refer to the drawing for a representation of the "A" dimension. DO NOT attempt to modify dry sprinklers, since they are manufactured to this specific "A" dimension. The following table is used when the ambient temperature is maintained between 40°F/4°C and 60°F/16°C around the wet piping system. EXPOSED BARREL AMBIENT TEMPERATURE (°F/°C) Ambient Temperature Exposed Minimum Barrel•1tTi1I, inches/mm r40 30 I_76 10 _ -12 203 25 0 0 12 -18 305 0 -10 14 -23 356 102 25 -20 14 6 3 -29 356 152 76 -30 16 i8 4 -34 406 203 102 -40 18 8 4 -40 457 203 102 -50 20 10 6 -46 508 254 152 -60 20 10 6 -51 508 254 152 NO I : taposea minimum oarrel iengtns are incluSive up to 30-mph/48-kprl wind velocities www.victaulic.com j4'tauiic' VIcTAULIc IS REGISTERED TRADEMARK OF vIcTAuLIc COMPANY. 6 2009 vlcTAuuc COMPANY. ALL RIGHTS RESERVED. 40.608 REV V36, K56 Dry Type Standard Spray Pendent, Intermediate Level Pendent & Recessed Pendent V3605 STANDARD RESPONSE V3606 QUICK RESPONSE WARRANTY 7 ~171 FLUSH SLEEVE AND SKIRT USTED PLAIN BARREL INTERMEDIATE EXTENDED RECESSED Refer to the Warranty section of the current Price List or contact Victaulic for details. NOTE This product shall be manufactured by Victaulic or to Victaulic specifications. All products to be installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations. US & WORLD HEADQUARTERS CANADA CENTRAL AND SOUTH AMERICA P.O. Box 31 905-884-7444 1-610-559-3300 Easton, PA 18044-0031 USA 905-884-9774 (fax) 1-610-559-3608 (fax) 4901 Kesslersville Road viccanada@victaulic.com vical@victaulic.com Easton, PA 18040 USA EUROPE ASIA PACIFIC 1-800-PICK-VIC (1-800-742-5842) 32-9-381-15-00 86-21-54253300 1-610-559-3300 32-9-380-44-38 (fax) 86-21-54253671 (fax) 1-610-250-8817 (fax) viceuro@victaulic.be vicap@victaulic.com pickvic@victaulic.com UNITED KINGDOM MIDDLE EAST www.victaulic.com 44 (0) 143831690 971-4-883-88-70 44 (0) 1438310699 (fax) 971-4-883-88-60 (fax) viceuro@victaulic.be UPDATED 11/2009 40.60 3123 REV H VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 6' 2009 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 40.60 \4tauIIc