Loading...
HomeMy WebLinkAbout2077 LAS PALMAS DR; ; FPC2018-0187; PermitPERMIT REPORT Cr'city of Carlsbad Print Date: 12/02/2020 Permit No: FPC2018-0187 Job Address: 2077 LAS PALMAS DR, CARLSBAD, CA 92011-1519 Status: Closed - Finaled Permit Type: FIRE-Construction Commercial Work Class: Fire Sprinklers Parcel #: 2130611800 Track #: Applied: 06/20/2018 Valuation: $419,380.67 Lot #: Issued: 07/19/2018 Occupancy Group: Project #: Finaled Close Out: 12/02/2020 #of Dwelling Units: Plan #: Bedrooms: Construction Type: Bathrooms: Orig. Plan Check #: Inspector: Plan Check #: Final Inspection: Project Title: Description: SYMBIENT - SPRINKLER TI (72 HEADS) OFFICE TO OFFICE Applicant: FPContractor: AMERICAN AUTOMATIC FIRE SUPPRESSION AMERICAN AUTOMATIC FIRE SUPPRESSION INC INC JAZZMIN DEEKEN 9925 PROSPECT AVE, # STE B 9925 PROSPECT AVE, #B SANTEE, CA 92071 SANTEE, CA 92071 (619) 562-3010 (619) 562-3010 FEE AMOUNT FIRE NFPA 13 or 13R System 7 - 100 heads $536.00 Total Fees: $536.00 Total Payments To Date: $536.00 Balance Due: $0.00 Fire Department Page 1 of 1 1635 Faraday Avenue, Carlsbad CA 92008-7314 1 760-602-4665 1 760-602-8561 f I www.carlsbadca.gov tqcci Fire Protection Products Worldwide I www.tyco-fire.com Contacts Series ELO-231 - 112 K-factor f=F(: Z019 °L'I- Upright and Pendent Sprinklers Standard Response, Standard Coverage General Description TYCO Series ELO-231 11.2K Stan- dard Response, Standard Coverage Upright and Pendent Sprinklers (Ref. Figure 1) are automatic sprinklers of the fusible solder type. They are stan- dard response, spray sprinklers that produce a hemispherical water distri- bution pattern below the deflector. The 11.2 K-factor, ELO-231 Sprinklers were subjected to full scale, high-piled storage, fire tests to qualify their use in lieu of 5.6 or 8.0 K-factor standard spray sprinklers for the protection of high-piled storage. Higher flow rates can be achieved at much lower pressures with the 11.2 K-factor, ELO-231 Sprinklers, making their use highly advantageous in high density applications, such as the pro- tection of high-piled storage. Wax or lead coatings can be used to extend the life of the copper alloy components used in Series ELO-231 sprinklers beyond that which would otherwise be obtained when exposed to corrosive atmospheres. Although wax and lead coated sprinklers have passed the standard corrosion tests of the applicable approval agencies, the testing is not representative of all pos- sible corrosive atmospheres. Conse- quently, it is recommended that the end user be consulted with respect to the suitability of these corrosion resistant coatings for any given corrosive envi- ronment. The effects of ambient tem- perature, concentration of chemicals, and gas/chemical velocity, should be considered, as a minimum, along with the corrosive nature of the chemical to which the sprinklers will be exposed. An upright intermediate level version of the Series ELO-231 Sprinklers for in-rack applications can be obtained by utilizing the Series ELO-231 Upright Sprinkler with the WSG-2 Guard & Shield, and a pendent intermediate level version of the Series ELO-231 Sprinklers can be obtained by utilizing the Series ELO-231 Pendent Sprinkler with the WS-2 Shield. If there is a pos- sibility of the pendent intermediate level version being exposed to mechanical damage, a G-2 Guard can be added. NOTICE The 11.2 K-factor, Series ELO-231 Upright and Pendent Sprinklers described herein must be installed and maintained in compliance with this document, as well as with the applica- ble standards of the National Fire Pro- tection Association (NFPA), in addition to the standards of any other authori- ties having jurisdiction. Failure to do so may impair the performance of these devices. The owner is responsible for main- taining their fire protection system and devices in proper operating con- dition. Contact the installing contrac- tor or product manufacturer with any questions. Installation of Series ELO-231 Pendent Sprinklers in recessed escutcheons will void all sprinkler warranties, as well as possibly void the sprinkler's Approvals and/or Listings. Sprinkler Identification Numbers (SINs) TY5111 -Upright 11.2K, 3/4" NPT 1Y5211 - Pendent 11.2K, 3/4" NPT TY5811 - Upright 11.2K, 1/2" NPT TY5111 is a redesignation for Central SIN C5111. TY5211 is a redesignation for Central SIN C5211. TY5811 is a redesignation for Central SIN C5811. IMPORTANT Always refer to Technical Data Sheet TFP700 for the "INSTALLER WARNING" that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and installation can permanently damage a sprinkler system or its compo- nents and cause the sprinkler to fail to operate in a fire situation or cause it to operate prematurely. Page 1 of 4 JANUARY 2017 TFP34O TFP34O Page 2 of 4 1/2 (12,7 mm) Components: T _____ [NOMINAL MAKE-IN 1 - Frame ____ NPT 1 3-Cap ______ ______ 2 4-Strut 2-13/16 Assembly THREAD (71,4 mm) !WRENCH 7 5 - Compression 3 Screw 8 6- Deflector* I 4 2 - Seal Disc TYP. FLATS RELIEF 7 - Helper 9 Spring NPT 1/2 3/4" 5 -___. 8 - Ejector Spring NPT 6 9 - Strut Clip L 7/16 (11,1 mm) 1/2 (12,7 mm) * Temperature NOMINAL MAKE-IN NOMINAL MAKE-IN rating is UPRIGHT UPRIGHT PENDENT CROSS indicated on TY5811 TY5111 TY5211 SECTION deflector FIGURE 1 SERIES ELO-231 11.2K UPRIGHT - 3/4" NPT (TY5111), UPRIGHT - 1/2" NPT (TY5811), AND PENDENT - 3/4" NPT (TY5211) SPRINKLERS Technical Data Approvals UL and C-UL Listed FM Approved NYC Approved (Refer to Table A for complete approval information, including corrosion-resis- tant status. The approvals apply to the service conditions indicated in the Design Criteria section.) Maximum Working Pressure 175 psi (12,1 bar) Discharge Coefficient K=11.2 gpm/p5i112 (161,4 1pm/bar1/2) Temperature Ratings Refer to Table A Finishes Refer to Table A Physical Characteristics Frame ............................Bronze Seal Disc .........................copper Strut Assembly. . Solder, Cap ..............................Bronze Bronze Stainless Steel Compression Screw .................Bronze Deflector ..........................Bronze Helper Spring ...............Stainless Steel Ejector Spring ......................Nickel Strut Clip ................... Stainless Steel Design Criteria UL and C-UL Listing Requirements TYCO Series ELO-231 11.2K Standard Response, Standard Coverage Upright and Pendent Sprinklers are to be installed in accordance with NFPA 13 standard sprinkler position and area/ density flow calculation requirements for light, ordinary, or extra hazard occu- pancies, as well as high piled storage occupancies (solid piled, palletized, rack storage, bin box, and shelf storage including but not limited to Class l-IV and Group A plastics) with a minimum residual (flowing) pressure of 7 psi (0,5 bar) for wet or dry pipe systems. FM Approval Requirements The 11.2 K-factor, Model ELO-231 (TY5111, TY5211, and TY5811) Sprin- klers are to be installed in accordance with the applicable control mode density/area guidelines provided by FM Global. (FM Approval guidelines may differ from UL and C-UL Listing criteria.) Operation A fusible alloy is sealed into a bronze actuating rod (center strut) by a stain- less steel ball. When the alloy melts at its rated temperature, the ball is forced upward into the center strut, releas- ing the two ejectors and operating the sprinkler. Installation TYCO Series ELO-231 11.2K Stan- dard Response, Standard Coverage Upright and Pendent Sprinklers must be installed in accordance with this section. A leak-tight 3/4 inch NPT sprinkler joint should be obtained by applying a min- imum-to-maximum torque of 10 to 20 lbs.-ft. (13,4 to 26,8 Nm). A leak-tight 1/2 inch NPT sprinkler joint should be obtained by applying a minimum-to- maximum torque of 7 to 14 lbs.-ft. (9,5 to 19,0 Nm). Higher levels of torque can distort the sprinkler inlet with con- sequent leakage or impairment of the sprinkler. "FITTING SIDE" TOWARDS SPRINKLER FITTING 01 /\ WRENCH RECESS / (END "A") FIGURE 2 W-TYPE 3 SPRINKLER WRENCH Do not attempt to make up for insuf- ficient adjustment in the escutcheon plate by under- or over-tightening the sprinkler. Re-adjust the position of the sprinkler fitting to suit. The Series ELO-231 Upright and Pendent Sprinklers must be installed in accordance with the following instructions: Step 1. Pendent sprinklers are to be installed in the pendent position, and upright sprinklers are to be installed in the upright position. Step 2. With pipe thread sealant applied to the pipe threads, hand tighten the sprinkler into the sprinkler fitting. Step 3. Tighten the sprinkler into the sprinkler fitting using only the W-Type 3 Sprinkler Wrench (Ref. Figure 2), except' that an 8 or 10 inch adjustable Crescent wrench is to be used for wax coated sprinklers. With reference to Figure 1, the W-Type 3 Sprinkler Wrench or the adjustable wrench, as applicable, is to be applied to the wrench flats. TFP34O Page 3 of 4 SPRINKLER FINISH SPRINKLER TEMPERATURE FRAME NATURAL CHROME LEAD WAX WAX-OVER-LEAD TYPE RATING COLOR BRASS PLATED COATED COATED COATED 165°F (74°C) Unpainted UPRIGHT 1,2,3,4 1, 2, 3, 4 212 F(100 C) White (TY511I &TY5811) 286°F (141°C) Blue 1,2,3,4 1°, 2°, 3* 4* 165°F (74°C) Unpainted (TY5211) PENDENT 1,2,4 1,2,3,4 212-F(100 C) White 286°F(141°C) Blue 1, 2,4 1*, 2°, 4* Notes: 3. FM Approved UL Listed 4. Approved by the City of New York (NYC) under MEA 291-04-E C-Ui Listed * Listed/Approved for a maximum ceiling temperature of 150*F (66*C) TABLE A 11.2K SERIES ELO-231 UPRIGHT & PENDENT SPRINKLERS, STANDARD RESPONSE LABORATORY LISTINGS AND APPROVALS When installing wax-coated sprinklers with the adjustable wrench, additional care needs to be exercised to prevent damage to the wax coating on the sprinkler wrench flats or frame arms and, consequently, exposure of bare metal to the corrosive environment. The jaws of the wrench should be opened sufficiently wide to pass over the wrench flats without damaging the wax coating. Before wrench-tightening the sprinkler, the jaws of the wrench are to be adjusted to just contact the sprin- kler wrench flats. After wrench-tight- ening the sprinkler, loosen the wrench jaws before removing the wrench. After installation, the sprinkler wrench flats and frame arms must be inspected and the wax coating re-touched (repaired) whenever the coating has been damaged and bare metal is exposed. The wax coating on the wrench flats can be retouched by gently applying a heated 1/8 inch diameter steel rod to the areas of wax that have been damaged, to smooth it back over areas where bare metal is exposed. Note. Onlyretouchingof the wax coating applied to the wrench flats and frame arms is permitted, and the retouching is to be performed only at the time of the initial sprinkler installation. The steel rod should be heated only to the point at which it can begin to melt the wax, and appropriate precau- tions need to be taken, when handling the heated rod, in order to prevent the installer from being burned. If attempts to retouch the wax coating with complete coverage are unsuc- cessful, additional wax can be ordered in the form of a wax stick (the end of which is color coded). Only the correct color-coded wax is to be used, and retouching of wrench flats and frame arms is only permitted at the time of initial sprinkler installation. With the steel rod heated as previously described, touch the rod to the area requiring additional wax with the rod angled downward, and then touch the wax stick to the rod approximately 1/2 inch away from the area requiring retouching. The wax will melt and run down onto the sprinkler. Care and Maintenance TYCO Series ELO-231 11.2K Standard Response, Standard Coverage Upright and Pendent Sprinklers must be main- tained and serviced in accordance with this section. Before closing a fire protection system control valve for maintenance work on the fire protection system that it con- trols, permission to shut down the affected fire protection system must be obtained from the proper authorities and all personnel who may be affected by this action must be notified. Sprinklers that are found to be leaking or exhibiting visible signs of corrosion must be replaced. Automatic sprinklers must never be painted, plated, coated or otherwise altered after leaving the factory. Modi- fied or over-heated sprinklers must be replaced. Care must be exercised to avoid dam-age to the sprinklers before, during, and after installation. Sprin- klers damaged by dropping, striking, wrench twist/slippage, or the like, must be replaced. Frequent visual inspections are rec- ommended to be initially performed for corrosion resistant sprinklers, after the installation has been completed, to verify the long term potential integrity of the sprinkler coatings. Thereafter, annual inspections per NFPA 25 should suffice; however, instead of inspecting from the floor level, a random sampling of close-up visual inspections should be made, so as to better determine the exact sprinkler condition and the long term integrity of the corrosion resistant coating, as it may be affected by the corrosive conditions present. The owner is responsible for the inspection, testing, and maintenance of their fire protection system and devices in compliance with this document, as well as with the applicable standards of the National Fire Protection Asso- ciation (e.g., NFPA 25), in addition to the standards of any other authorities having jurisdiction. Contact the install- ing contractor or product manufacturer with any questions. It is recommended that automatic sprinkler systems be inspected, tested, and maintained by a qualified Inspec- tion Service in accordance with local requirements and/or national codes. TFP34O Page 4 of 4 P/N 50 - XXX - X - I XXX I I SPRINKLER j TEMPERATURE FINISH RATING 1 NATURAL BRASS 112 11.2K PENDENT (3/4" NPT) TY5211 WAX 165 165'F (74-C) 6 COATED 7 LEAD 210 11.2K UPRIGHT (1/2" NPT) TY2811 212 212'F (100-C) COATED 286 286°F (141°C) WAX-OVER-LEAD 8 COATED CHROME PLATED TABLE B SERIES EL0231 11.2K UPRIGHT AND PENDENT SPRINKLERS, STANDARD RESPONSE PART NUMBER SELECTION SIN 110 11.2K UPRIGHT (3/4" NPT) TY51I1 Limited Warranty For warranty terms and conditions, visit www.tyco-fire.com. Ordering Procedure Contact your local distributor for avail- ability. When placing an order, indicate the full product name and part number (P/N). Sprinkler Specify: ELO-231 11.2K Standard Response (specify Pendent or Upright) Sprinkler, SIN (specify), temperature rating (specify), with (specify) finish, P/N (specify from Table B) Sprinkler Wrench Specify: W-Type 3 Sprinkler Wrench, P/N 56-895-1-001 Wax Sticks (for retouching wrench-damaged wax coating) Specify: (specify Color) color-coded Wax Stick for retouching (specify temperature rating) temperature- rated Series ELO-231 Sprinklers, P/N (specify): Red for 165°F ................. 56-065-1 -155 Blue for 212°F and 286°F ....... 56-065-1 -286 Note: Each wax stick is suitable for retouching up to twenty-five sprinklers. The wax used for 286°F sprinklers is the same as for 212°F sprinklers, and, therefore, the 286°F sprinkler is limited to the same maximum ceiling tempera- ture as the 212°F sprinkler (i.e., 1500F). GLOBAL HEADQUARTERS 11400 Pennbrook Parkway, Lansdale, PA 19446 I Telephone +1-215-362-0700 Copyright © 2017 Tyco Fire Products, LP. All rights reserved. tqco Fire Protection Products tqccs Worldwide Fire Protection Contacts www.tyco-fire.com Products Series TY-FRB, 56 K-factor Upright, Pendent, and Recessed Pendent Sprinklers Quick Response, Standard Coverage General Description The TYCO Series TY-FRB, 5.6 K-factor, Upright (TY313) and Pendent (TY323) Sprinklers described in this data sheet are quick response, standard coverage, decorative 3 mm glass bulb-type spray sprinklers designed for use in light or ordinary hazard, commercial occupan- cies such as banks, hotels, and shop- ping malls. The recessed version of the Series TY- FRB Pendent Sprinkler, where applica- ble, is intended for use in areas with a finished ceiling. This recessed pendent sprinkler uses one of the following: A two-piece Style 15 Recessed Escutcheon with recessed adjust- ment up to 5/8 inch (15,9 mm) from the flush pendent position. A two-piece Style 20 Recessed Escutcheon with recessed adjust- ment up to 1/2 inch (12,7 mm) from the flush pendent position. The adjustment provided by the Recessed Escutcheon reduces the accuracy to which the fixed pipe drops to the sprinklers must be cut. Intermediate level versions of Series TY-FRB Sprinklers are described in Technical Data Sheet TFP357. Sprin- kler guards and shields are described in Technical Data Sheet TFP780. IMPORTANT Always refer to Technical Data Sheet TFP 700 for the "INSTALLER WARNING" that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and installation can permanently dam- age a sprinkler system or its compo- nents and cause the sprinkler to fail to operate in a fire situation or cause it to operate prematurely. Page 1 of 4 NOTICE The TYCO Series TY-FRB Sprinklers described herein must be installed and maintained in compliance with this doc- ument, as well as with the applicable standards of the National Fire Protec- tion Association, in addition to the stan- dards of any other authorities having jurisdiction. Failure to do so may impair the performance of these devices. The owner is responsible for maintain- ing their fire protection system and devices in proper operating condition. The installing contractor or sprinkler manufacturer should be contacted with any questions. Sprinkler Identification Number (SIN) TY313 .......Upright 5.6K, 1/2"NPT TY323 ......Pendent 5.6K, 1/2" NPT Technical Data Approvals UL and C-UL Listed FM, LPCB, and VdS Approved CE Certified Sprinklers with Polyester Finish are UL and C-UL Listed as Corrosion-Resis- tant Sprinklers. Maximum Working Pressure 175 psi (12.1 bar) 250 psi (17.2 bar)* *The maximum working pressure of 250 psi (17.2 bar) only applies to the listing by Un- derwriters Laboratories, Inc. (UL). Discharge Coefficient K=5.6 GPM/ps1112 (80,6 LPM/barll2) FEBRUARY 2014 Temperature Rating 135°F (57°C) 155°F (68°C) 175°F (79°C) 200° F (93°C) 286°F (141°C) Finishes Sprinkler: Refer to Table A Recessed Escutcheon: White Coated, Chrome Plated, or Brass Plated Physical Characteristics Frame ...................Bronze Button..............Brass/Copper Sealing Assembly .........Stainless Steel w/TEFLON Bulb ......................Glass Compression Screw........Bronze Deflector.................Bronze TFPI72 TFPI72 Page 2 of 4 Components: 1 - Frame 2 - Button 3 - Sealing Assembly * Temperature rating is ** Pipe thread connections per ISO 7-1 4 - Bulb indicated on Deflector. can be provided on special request. 5 - Compression Screw ESCUTCHEON PLATE 1/2 7/16 (11,1 mm) 6 - Deflector* DEFLECTOR* SEATING SURFACE NPT** NOMINAL MAKE-IN STYLE 15 or 20 RECESSED ESCUTCHEON 1 7/16 (11,1 mm) I NOMINAL MAKE-IN 2 (50,8 mm) 1/2 NPT** 2' (50,8 mm) WRENCH FLATS DEFLECTOR * b-.--- 2-7/8" (73,0 mm) DIA. CROSS SECTION UPRIGHT PENDENT RECESSED PENDENT FIGURE 1 SERIES TY-FRB UPRIGHT (TY313) AND PENDENT (TY323) SPRINKLERS 5.6 K-FACTOR, 1/2 INCH NPT, QUICK RESPONSE Operation The glass bulb contains a fluid which expands when exposed to heat. When the rated temperature is reached, the fluid expands sufficiently to shatter the glass bulb, allowing the sprinkler to activate and water to flow. Design Criteria The TYCO Series TY-FRB, 5.6 K-factor, Upright (TY313) and Pendent (TY323) Sprinklers are intended for fire protec- tion systems designed in accordance with the standard installation rules rec- ognized by the applicable Listing or Approval agency (such as, UL Listing is based on the requirements of NFPA 13, and FM Approval is based on the requirements of FM's Loss Prevention Data Sheets). Only the Style 15 or Style 20 Recessed Escutcheon is to be used for recessed pendent installations. Installation The TYCO Series TY-FRB, 5.6 K-factor, Upright (TY313) and Pendent (TY323) Sprinklers must be installed in accor- dance with this section. General Instructions Do not install any bulb-type sprinkler if the bulb is cracked or there is a loss of liquid from the bulb. With the sprin- kler held horizontally, a small air bub- ble should be present. The diameter of the air bubble is approximately 1/16 inch (1,6 mm) for the 135°F (57°C) and 3/32 inch (2,4 mm) for the 286°F (141°C) temperature ratings. A leak-tight 1/2 inch NPT sprinkler joint should be obtained by applying a min- imum to maximum torque of 7 to 14 ft.-lbs. (9,5 to 19,0 Nm). Higher levels of torque can distort the sprinkler Inlet with consequent leakage or impairment of the sprinkler. Do not attempt to compensate for insufficient adjustment in the Escutch- eon Plate by under- or over-tightening the sprinkler. Re-adjust the position of the sprinkler fitting to suit. Upright and Pendent Sprinklers The Series TY-FRB Upright and Pen- dent Sprinklers must be installed in accordance with the following instructions. Step 1. Install Pendent sprinklers in the pendent position. Install upright sprin- klers in the upright position. Step 2. With pipe-thread sealant applied to the pipe threads, hand- tighten the sprinkler into the sprinkler fitting. / WRENCH RECESS / (USE ONLY FIGURE 2 W- TYPE 6 SPRINKLER WRENCH WRENCH RECESS PUSH WRENCH IN TO ENSURE ENGAGEMENT WITH SPRINKLER WRENCHING AREA FIGURE 3 W- TYPE 7 RECESSED SPRINKLER WRENCH TFPI72 Page 3 of 4 Step 3. Tighten the sprinkler into the sprinkler fitting using only the W-Type 6 Sprinkler Wrench (Figure 2). With ref- erence to Figure 1, apply the W-Type 6 Sprinkler Wrench to the wrench flats. Torque sprinklers 7 to 14 ft.-lbs. (9,5 to 19,0 Nm). Recessed Pendent Sprinklers The Series TY-FRB Recessed Pendent Sprinklers must be installed in accor- dance with the following instructions. Step A. After installing the Style 15 or Style 20 Mounting Plate over the sprin- kler threads, and with pipe-thread sealant applied to the pipe threads, hand-tighten the sprinkler into the sprinkler fitting. Step B. Tighten the sprinkler into the sprinkler fitting using only the W-Type 7 Recessed Sprinkler Wrench (Figure 3). With reference to Figure 1, apply the W-Type 7 Recessed Sprinkler Wrench to the sprinkler wrench flats. Torque sprinklers 7 to 14 ft.-Ibs. (9,5 to 19,0 Nm). Step C. After ceiling installation and fin- ishing, slide on the Style 15 or Style 20 Closure over the Series TY-FRB Sprin- kler and push the Closure over the Mounting Plate until its flange comes in contact with the ceiling. Care and Maintenance The TYCO Series TY-FRB, 5.6 K-factor, Upright (TY313) and Pendent (TY323) Sprinklers must be maintained and ser- viced in accordance with this section. Before closing a fire protection system main control valve for maintenance work on the fire protection system that it controls, obtain permission to shut down the affected fire protection systems from the proper authorities and notify all personnel who may be affected by this action. Absence of the outer piece of an escutcheon, which is used to cover a clearance hole, can delay sprinkler operation in a fire situation. The owner must assure that the sprin- klers are not used for hanging any objects and that the sprinklers are only cleaned by means of gently dusting with a feather duster; otherwise, non- operation in the event of a fire or inad- vertent operation may result. Sprinklers which are found to be leak- ing or exhibiting visible signs of corro- sion must be replaced. Automatic sprinklers must never be painted, plated, coated, or other- wise altered after leaving the factory. Modified sprinklers must be replaced. Sprinklers that have been exposed to corrosive products of combustion, but have not operated, should be replaced if they cannot be completely cleaned by wiping the sprinkler with a cloth or by brushing it with a soft bristle brush. Care must be exercised to avoid dam- age to the sprinklers before, during, and after installation. Sprinklers damaged by dropping, striking, wrench twist/ slippage, or the like, must be replaced. Also, replace any sprinkler that has a cracked bulb or that has lost liquid from its bulb. (Ref. Installation Section.) The owner is responsible for the inspection, testing, and maintenance of their fire protection system and devices in compliance with this document, as well as with the applicable standards of the National Fire Protection Associa- tion (e.g., NFPA 25), in addition to the standards of any other authorities hav- ing jurisdiction. Contact the installing contractor or sprinkler manufacturer regarding any questions. Automatic sprinkler systems are rec- ommended to be inspected, tested, and maintained by a qualified Inspec- tion Service in accordance with local requirements and/or national codes. - 2-7/8 DIA. (73,0 mm) 2-1/4 DIA. FACE OF H57,2 mm) SPRINKLER FITTING 5/8' (15,9 mm) FLUSH 3/8±5/16' (9,5±7,9 mm) MOUNTING 1/8 J SURFACE mm) CLOSURE SERIES MOUNTING 1-3/8' (34,9 mm) TY-FRB PLATE 3/4" (19,1 mm) FIGURE 4 SERIES TY-FRB RECESSED PENDENT SPRINKLER ASSEMBLY (TY323) WITH TWO PIECE 5/8 INCH TOTAL ADJUSTMENT STYLE 15 RECESSED ESCUTCHEON 2-7/8' DIA. (73,0 mm) FACE OF SPRINKLER - 2-1/4' DIA. 1/2' (12,7 mm) FITTING (57,2 mm) 5/16±1/4" (7,9±6,4 mm) FLUSH 17, MOUNTING (3,2 \ J I SURFACE mm) CLOSURE SERIES MOUNTING 1-3/8" (34,9 mm) TYFRB PLATE 7/8 (22,2 mm) FIGURE 5 SERIES TY-FRB RECESSED PENDENT SPRINKLER ASSEMBLY (TY323) WITH TWO PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 20 RECESSED ESCUTCHEON TFPI72 Page 4 of 4 PIN*77_XXX_X_XXX I I SPRINKLER TEMPERATURE I FINISH -i- RATINGS SIN 1 NATURAL BRASS I 370 I 5.6K UPRIGHT (1/2- NPT) TY313 3 PURE WHITE (RAL9010)** POLYESTER 371 5.6K PENDENT (1/2 NPT) TY323 POLYESTER SIGNAL WHITE (RAL9003) * Use suffix I" for ISO 7-1 connection; 9 CHROME PLATED for example, 77-370-4-175-I - ** Eastern Hemisphere sales only TABLE A SERIES TY-FRB UPRIGHT AND PENDENT SPRINKLERS PART NUMBER SELECTION 135 135°F(57°C) 155 155°F (68°C) 175 175°F(79°C) 200 200°F (93°C) 286 286°F (141°C) Limited Warranty For warranty terms and conditions, visit www.tyco-fire.com. Ordering Procedure Contact your local distributor for avail- ability. When placing an order, indicate the full product name and Part Num- ber (P/N). Sprinkler Assemblies with NPT Thread Connections Specify: Series TY-FRB Upright or Pen- dent (specify) Sprinkler, SIN (specify), K=5.6, Quick Response, (specify) tem- perature rating, (specify) finish, P/N (specify, refer to Table A). Recessed Escutcheon Specify: Style 15 Recessed Escutcheon with (specify*) finish, P/N (specify*) Specify: Style 20 Recessed Escutch- eon with (specify*) finish, P/N (specify*) * Refer to Technical Data Sheet TFP770 Sprinkler Wrench Specify: W-Type 6 Sprinkler Wrench, P/N 56-000-6-387 Specify: W-Type 7 Sprinkler Wrench, P/N 56-850-4-001 GLOBAL HEADQUARTERS 11400 Pennbrook Parkway, Lansdale, PA 19446 I Telephone +1-215-362-0700 Copyright © 2014 Tyco Fire Products, LP. All rights reserved. tqco TEFLON is trademark of The DuPont Corporation. Fire Protection Products I Malleable Iron Threaded Pipe Unions Pressure - Temperature Ratings Temperature Pressure Class 150 Class 250 Class 300 (°F) (°C) psi bar psi bar psi bar 200 to 1500 -28.9° to 65.60 300 20.7 500 34.5 600 47.4 2000 93.30 265 18.3 455 31.4 550 37.9 2500 121.10 225 15.5 405 27.9 505 3.8 3000 148.90 185 12.8 360 24.8 460 37 3500 176.70 150 10.3 315 21.7 415 28.6 4000 204.40 110 7.6 270 18.6 370 25.5 4500 232.20 75 5.2 225 15,5 225 22.4 5000 260.00 - - 180 12.4 280 19.3 550° 287.80 - - 130 9.0 230 15.9 Note: Unions with Copper or Copper Alloy seats are not intended for use whore :ernperature exceeds 450°F ®us c <:e~> APPROVED For Listings/Approval Details and Limitations, visit our wbsitc @ www.anvilintl.com or contact an Anvil/AnvilStar Sales ReDresentative. Malleable Iron Threaded Fittings Pressure - Temperature Ratings Temperature Pressure Class 150 Class 300 __________ Sizes ¼-i (6-25 mm) Sizes 11/4"-2" (32-51 mm) Sizes 21/2 _3" (64-76 mm) (°F) (°C) psi bar psi bar psi bar psi bar -200 to 1500 -28.90 to 65.60 300 20.7 2,000 137.9 1,500 103.4 1,000 68.9 2000 93.3 265 18.3 1,785 123.1 1,350 93.1 910 62.7 2500 121.1 225 15.5 1,575 108.6 1,200 82.7 825 56.9 300° 148.9 185 12.8 1 1,360 93.8 1,050 72.4 735 50.7 3500 176.7 150 10.3 1,150 79.3 1 900 62.1 650 44.8 4000 204.4 - - 935 64.5 750 51.7 560 38.6 4500 232.2 - - 725 50.0 600 41.4 475 32.8 5000 260.0 - - 510 35.2 450 31.0 1 385 26.5 550° 287.8 - - 300 20.7 300 20.7 1 300 20.7 Anvil Class 150/300 Malleable Iron Fittings conform to ASME B16.3 and Unions conform to ASME B16.39. ALL ELBOWS & TEES 3/s" (10 ON) and LARGER ARE 100% GAS TESTED AT A MINIMUM OF 100 PSI. (6.9 bar) www.anvilintl.com 17 best sprinkler pi in the industry! c®us LISTED <> APPROVED no Am.,tc.. F... NFPA BULL MOOSE TUBE COMPANY LII 1k1 IJ =1 =911111111111=1 VA I :/i ILI W El ull Moose Tube® is a customer focused, growth oriented manufacturer and marketer of tubular products, where success is based on a commitment to meeting the customer's perception of quality. Our strength resides in our people working together to satisfy customers and to promote business growth by achieving superior financial performance. www.BullMooseTube.com sales@bullmoosetube.com 800.325.4467 AN c®us LISTED APPROVED Do A A....k,Th. ONFSA NFPA BULL MOOSE TUBE COMPANY 2 Bull Moose Tube's® "Eddy Pipe®" brand sprinkler pipe is produced to meet sprinkler pipe standards and applications. c®usLISTED <> APPROVED no 1r4 NFPA ADVANTAGES OF BULL MOOSE TUBE® EDDY PIPE® FAMILY All pipe products are UL Listed (for U.S. and Canada), and have been approved by Factory Mutual. Excellent production and coating capabilities, tighter tolerances, and our unique steel properties make our pipe excellent for roll grooving, welding, threading, and plain end fittings. All products are certified to ASTM Al 35 and A795 Type E, Grade A. Available in specific cut to order lengths from regular mill rollings. More popular sizes available with coating or bare. Ultra Eddy®, Eddy Flow®, Eddylite®, and Eddythread 40® offer cost savings along with superior hydraulics without compromising service life. Sprinkler pipe inventory stocked in Masury, Ohio; Gerald, Missouri; Casa Grande, Arizona; Kent, Washington; and Dallas, Texas. All Bull Moose (black) sprinkler pipe includes our exclusive EDDY GUARD Il® MlC preventative coating. Bull Moose Tube® sprinkler pipe is FBCTM compatible. PRODUCTS Schedule 10 and Schedule 40: FM approved and UL listed sprinkler pipe. Eddythrcad 40®: Light threadable Schedule 40 replacement with corrosion resistance ratio of 1.0. Eddylite®: Lightwall threadable with standard outside diameter. Eddy Flow®: Cost effective replacement for Schedule 10. Ultra Eddy®: Lightwall roll groovable pipe. Bull Moose galvanized steel sprinkler pipe is hot dipped galvanized to meet ASTM Al 23 standards. All products are stencilled to meet FM & UL specifications. PROTECTION Eddy Guard Il®: Bull Moose Tube® is producing product that can resist bacteriological growth even after multiple rinse-outs. You know MIC corrosion can impact your installation and your property. Specify Bull Moose Tube® "Eddy Guard Il®" and feel comfortable knowing that you are getting Eddy Pipe® product you trust with the bacteria resistance you need. Eddy Guard Il® is NFPA 13 and NFPA 13R system compatible for use in hybrid systems as well as FM approved. All information contained herein is accurate as known at the time of publication. Bull Moose Tubes reserves the right to change product specifications without notice and without incurring obligation. Moose Tube's® Schedule i.' 10 and Schedule 40 are FM B SCHEDULE 10 PIPE SPECIFICATIONS Approved and UL Listed (for U.S. NOMINAL PIPE O.D. I.D. WATER FILLED BUNDLE and Canada), even though these SIZE (IN) (IN) (IN) CRR** WEIGHT/FT WEIGHT SIZE products do not require separate j approvals and listings Bull [ 1 1.315 1.097 1527 it 1.41 lbs/ft L1!P 91 Moose Tube® made the decision L ll/4JLT66o TTIL 1442] 91 :i:: to have them approved and lFsted 1 1/2 ' 1900 -- 1.682 776 209lbIf-t jr 3053 -- 61 Our Schedule 10 and Schedule 40 I 2 J[I2375J[ p157 I[67 164Ibs/f-tJfl 4T21 37 have a pressure rating of 300 PSI 21/2 2.875 2.635 4.92 '3.53 lbs/ft - --5.893 30 and have been through the same E_3 T E3 500 ]fl3 260 ]354 434 lbs/ft iL757 1I.19IJ rigorous testing as our other fine 4 4.500--y 4260 - 250 52Ibs/ft ETh1 796] 19 - pipe products. Schedule iu can De supplied roll grooved or plain end. Bull Moose Tubes® Schedule 10 and Schedule 40 pipes are hot dipped galvanized to meet ASTM A123 standards. All products are _ stencilled to meet FM .,& UI specifications. c®us LISTED APPROVED mo NFPN 4 SCHEDULE 40 PIPE SPECIFICATIONS -- NOMINAL PIPE O.D. I.D. WATER FILLED BUNDLE SIZE (IN) (IN) (IN) CRR** WEIGHT/FT WEIGHT SIZE 1.31 5 1.049 - 1.00 1.68 lbs/ft 2.055 70 EJJL4ETl166ojJL 1.380 ioo 1f2 27 I67+rflT 2918 51 '1-112 1.900 i.61O 1.00 2.72 lbft 44 EIIIITT [io0 r 30 2.875 2.468 1.00 5 80 lbs/ft 7.-875-- 3* 1T 3 5fl0 föö i[TjpttiIIE 10.783 - - 4* I 4500 4026 100 1080Ibs/fti 16.316 19 *Only available in Casa Grande, AZ **Corrosion Resistance Ratio per latest UL Directory listing PIPE PREPARATION For proper operation, all pipe surfaces should be cleaned prior to installation. In order to provide a leak-tight seat for the gasket, pipe surfaces should be free from indentations and projections from the end of the pipe to the groove. All loose paint, scale, dirt, chips, grease, and rust must be removed prior to installation. Failure to take these important steps may result in improper coupling assembly, causing leakage. Also, check the manufacturer's instructions for the specific fitting used. For Additional Information Contact (800) 325-4467 www.bullmoosetube.com Or From Canada Call: (800) 882-4666 saIes@bullmoosetube.com 1819 Clarkson Road - chesterfield, MO Gerald, MO Kent, WA Casa Grande, AZ Dallas, 1)( Masurt OH BULL IVIOOSETUflE CDNIRANV 63017 FireLock® Outlet-I ® K ILPCBI SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS STYLE 922 The Style 922 Outlet-T provides a convenient method of incorporating ½, 3/4, and 1/15, 20 and 25mm outlets for directly connecting sprinklers, drop nipples, sprigs, gauges, drains and other outlet products. Available for 114 through 76.1 mm/32 to 76.1 mm piping systems, Style 922 outlets are UL/ULC Listed, LPCB and FM Approved for branch connections and VdS Approved for direct sprinkler connection only on wet and dry systems. The locating collar engages into the hole prepared in the pipe. When tightened, the assembly compresses the gasket onto the OD of the pipe. The Style 922 Outlet-T is UL/FM rated up to 300 psi/2068 kPa and VdS rated up to 16 bar at the ambient temperatures typical for fire protection systems. Style 922 is suitable for use on standard, lightwall, Schedule 5 and other specialty pipes.* Contact Victaulic for other optional coatings. *Consult Section 10.01 for specific listings/approvals. MATERIAL SPECIFICATIONS Housing: Ductile iron conforming to ASTM A-536, grade 65-45-12. Ductile iron conforming to ASTM A-395, grade 65-45-15, is available upon special request. Gasket: Grade "E" EPDM - Type A (Violet color code). FireLock products have been Listed by Underwriters Laboratories Inc. and Approved by Factory Mutual Research for wet and dry (oil free air) sprinkler services up to the rated working pressure using the Grade "E" Type A Gasket System. Bolts/Nuts: Heat-treated plated carbon steel, trackhead meeting the physical and chemical requirements of ASTM A-449 and physical requirements of ASTM A-183. Housing Coating: Orange enamel (North America, Latin America, Asia Pacific) Red enamel (Europe) JOB/OWNER CONTRACTOR ENGINEER System No. Submitted By Spec Sect Para Location - Approved Date www.victaulic.com VICTAULIC IS REGISTERED TRADEMARK OF vlcTAuuc COMPANY. © 2009 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REV G 10.52 1 IPS CARBON STEEL PIPE - HOLE CUT PRODUCTS FireLock® Outlet-T Nominal Size Inches/mm Run X Branch Hole Diameter +0.0641.5 Dimensions - inches/millimeters Approx. Weight Each 777M, 1¼ ½ -0.001-0.0 1 3A6 - 1.30 1.83 1.10 3.87 2.56 1.0 x 32 15 30.2 33.0 46.5 27.9 98.3 65.0 0.45 3% 1/io 1.28 1.83 1,10 3.87 2.56 1.1 20 30.2 32.5 46.5 27.9 98.3 65.0 0.50 1 1 3A6 1.52 2.18 1.10 3.87 2.56 1.2 25 30.2 38.6 55.4 27.9 98.3 65.0 0.54 11/2 ½ 1/16 1.42 1.95 1.22 4.08 2.56 1.2 x 40 15 30.2 36.1 49.5 31.0 103.6 65.0 0.54 3/4 1 3A6 1.40 1.95 1.22 4.08 2.56 1.2 20 30.2 35.6 49.5 31.0 103.6 65.0 0.54 1 1 3/ 1.64 2.30 1.22 4.08 2.56 1.3 25 30.2 41.7 58.4 31.0 103.6 65.0 0.59 2 ½ 1 /r6 1.66 2.19 1.46 4.60 2.56 1.3 50 15 30.2 42.2 55.6 37.1 116.8 65.0 0.59 3% 1,i6 1.64 2.19 1.46 4.60 2.56 1.4 20 30.2 41.7 55.6 371 116.8 65.0 0.64 1 1 3/16 1.88 2.54 1.46 4.60 2.56 1.5 25 30.2 47.8 64.5 37.1 116.8 65.0 0.68 2½ ½ 1A6 1.91 2.44 1.71 5.40 2.56 1.6 x 65 15 30.2 48.5 62.0 43.4 137.2 J 65.0 0.73 '/4 1/6 1.89 2.44 1.71 5.40 2.56 1.6 20 30.2 48.0 62.0 1 43.4 137.2 65.0 1 0.73 1 1 "/16 2.13 2.79 1.71 5.40 2.56 1.6 25 30.2 54.1 70.9 43.4 137.2 65.0 0.73 ½ P16 1.91 2.44 1.71 5.50 2.56 1.6 X 76.1 mm 15 30.2 48.5 62.0 43.4 139.7 65.0 0.73 3% 11A6 1.89 2.44 1.71 5.50 2.56 1.6 20 32 48.0 62.0 43.4 139.7 65.0 0.73 1 1 3A6 2.13 1 2.79 1.71 5.50 2.56 1.7 25 30.2 54.1 1 70.9 1 43.4 139.7 , 65.0 0.80 STYLE 922 DIMENSIONS lw,1 t Victaulic female threaded products are designed to accommodate standard NPT or BSPT (optional) male pipe threads only. Use of male threaded products with special features, such as probes, dry pen- dent sprinklers, etc., should be verified as suitable for use with this Victaulic product. Failure to verify suitability in advance may result in assembly problems or leakage. *Center of run to engaged pipe end for NPT threads (dimensions are approximate). www.victaulic.com vicTAuLic IS REGISTERED TRADEMARK OF VICTAuLIc COMPANY. © 2009 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 10.52 2 \%taulic REV C IPS CARBON STEEL PIPE - HOLE CUT PRODUCTS 1U.3 PERFORMANCE Equivalent Length of 1 inch Schedule 40 Steel Pipe (per UL Run Size x Outlet Size 213, Section 16) (C=120)*, FT Inches/mm . Feet/meters 32 25 40 25 L1uui,i Jr -- Hazen-Williams coefficient of friction is 120 FireLock® Outlet-T STYLE 922 www.victaulic.com VICTAULIC IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2009 VICTAULIC COMPANY. ALL RIGHTS RESERVED. A_C_tau_lic~ FV r 10F2 FireLock® Outlet-T STYLE 922 INSTALLATION Reference should always be made to the 1-100 Victaulic Field Installation Handbook for the product you are installing. Handbooks are included with each shipment of Victaulic products for complete installation and assembly data, and are available in PDF format on our website at www.victaulic.com. WARRANTY Refer to the Warranty section of the current Price List or contact Victaulic for details. NOTE This product shall be manufactured by Victaulic or to Victaulic specifications. All products to be installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations. For complete contact information, visit www.victaulic.com 'JtaUIiC 10.52 3355 REV G UPDATED 12/2009 VICTAULIC IS A REGISTERED TRADEMARK OF vicrAuLic COMPANY. 2009 VIcTAULIc COMPANY. ALL RIGHTS RESERVED. 10.52 P.O. Box 3365 South El Monte, CA 91733 626.444.0541 Fax 626.444.3887 www. Afcon.org 300 RING HANGER 1 thru 4 inch pipe LISTED FOR STEELICPVC 112&3/4 Inch pipe 5 thru 8 inch pipe SIZE - ROD- 3/8" or 1/2" SIZE - SYSTEM PIPE - 1/2" thru 8" MATERIAL - Carbon Steel, Mu. Galvanized to G-90 spec. LISTING/APPROVAL - C@ us LISTED 25511 1'- 8" Approval guide - 1"- 8" OSHPD OPA-0601 See Website. CONFORMS WITH: Federal Specification WW-H-171E, Type 10. Manufacturers Standardization Society ANSI/MSS-SP-5 8 Type 10. MAXIMUM TEMPERATURE - 650°F. FUNCTION - Pipe hanger component of an AFCON hanger. To support steel, CPVC or copper pipe. INSTALLATION - Per NFPA 13, 13R, 13D, these instructions and the CPVC or copper pipe manufacturers instructions. FEATURES - * Sized and listed exclusively for use with #310 Surge Restrainer. * Band edge is offset for EASY pipe insertion. * Custom fit swivel nut for better retention in ring. ORDERING - Part #, pipe size. 11/09 NFPA 13 PIPE ROD I WT. 5WT.+250 UL TEST LOAD 1 1 3/8 30.75 403.75 750 11/4 3/8 43.95 469.75 750 11/2 3/8 54.15 520.75 750 2 3/8 76.95 1 634.75 750 21/2 3/8 118.35 1 841.75 850 3 3/8 162.30 1 1061.50 1050 4 1 3/8 246.00 1480.00 1500 5 1/2 349.45 1996.75 2000 6 1/2 476,35 2631.75 2650 8 1/2 711.00 3605.00 4050 551 P.O. Box 3365 South El Monte, CA 91733 626.444.0541 Fax 626.444.3887 www. Afcon.org 310 RING RESTRAINER Restraint SIZE - One size fits 3/4 thru 2 inch AFCON #300 Ring Hanger. MATERIAL - Carbon Steel. FINISH - Mil. Galvanized. LISTINGS - 'Ji. us 203-EX 2551 Listed only for use with AFCON#300 Ring Hanger. FUNCTION - To restrain movement of sprinkler pipe toward the knurl nut of the ring hanger. To prevent upward movement of pipe that supplies a pendent sprinkler below the ceiling. INSTALLATION - Per NFPA 13 and CPVC manufacturers instructions on steel, CPVC, or copper pipe. Snap into locking position on swivel nut of AFCON #300 Ring Hanger. SPECIAL NOTE: When installing on CPVC sprinkler system pipe: Verify that all assembly components are cleaned of any surface oil. FEATURES - * Listed only for use with AFCON #300 Ring Hanger. ORDERING - Part # and size. Specific AFCON AFCON products are exclusively designed to be compatible ONLY with other AFCON products including parts and fasteners, resulting in a listed sway brace, restrainer or hanger assembly. Be advised the following warranty restriction will apply. DISCLAIMER . AFCONwill NOT warrant against the failure of its products when used in combination with other products, parts orsystenis not manufactured or sold by AFCON. AFCON shall NOT be liable under any circumstances whatsoever for any director indirect, incidental or consequential damages of any kind, including but not limited to loss of business or profit, when non-AFCON products have been, or are used. 1/08 Product Features No pre-drilling required. Quick to install using the Sammy Nut Driver with an 18V cordless drill/driver. Saves time from traditional methods. Reduces installation cost. Made in the U.S.A. Not less than Wood Flooring 114 8003957 GST 200 114x 2' 1760 (Fir) 25 125 I 1/4 8004957 - GST 300 1/4x3 2060 (Fir) 25 125......] 3/8' 8006957 GST.75 114x3/4 564 (314" Ply) 25 125 3/8 8007957 GST 10 1/4 xl 210 (7116" OSB) 300 25 125 670 3/8" 8008957 GST 20 1/4x2 1760 (Fir) 850 1475 25 125 3/8' 8068925 GST öSS 1/4 x? 1760 (Fir) 850 25 318 8009925 GST 25-380 3/8x2-1I2 2113 (Fir) 1500 25 125 "14 lack 3/8 8010957 GST 30 1/4x3 2060 (Fir) 1500 1475 25 12( Nut Driver 3/8 8069925 GST 30-SS 1/4x3 2060 (Fir) 25 125 Part #8113910 3/8 80115 GST 40 1/474 2180 (Fir) 25 125_. 3/8 8012925 GST 60 114x6 2230 (Fir) 25 125 - 1/2 8013925 GST 2 1/4 x 2 1760 (Fir) 25 125 1 1/2 8014925 GST 2.5-380 3/8 x 2-1/2 2113 (Fir) 25 125 - 1/2 8015925 GST3 1/4x3 2275() 25 125J 112 8016925 GST4 114x4 2180 (Fir) 25 125 1/2 8017925 GST6 1/4x6 2230 (Fir) 25 i ...J #14SWRed Nut Driver Part #8114910 Product Features Eliminates distortion of threaded rod. • Saves time from traditional methods. Accommodates up to 3 '/" x 12 pitch roof. • Reduces installation cost. Allows 17 deflection from vertical. • Made in the U.S.A. 3/8' 8139957 SH-GST20 1/4x2 1257 (Fir) 1050 1475 25 125 3/8' 8141957 SH-GST 30 1/4x3' 1720 (Fir) 1500 1475 25 125 SPECIAL NUT DRIVER SYSTEM: The nut drivers were designed with a unique spin-off feature which provides a fast and safe installation each time. When the face of the driver comes into contact with the material you are installing into, continue drilling until nut driver spins free. Installation is then complete. Warranty requires the use of the appropriate nut driver for installations. #14 Black Nut Driver Part # 8113910 IN Floor Joist Product Features No pre-drilling required. Quick to install using the Sammy Nut Driver with an 18V cordless drill/driver. Saves time from traditional methods. Reduces installation cost. Made in the U.S.A. Not less than 2' nominal width (1-1/2') up to 3-1/2' pipe; not less than 3' (2-1/2') nominal width 4' & 5' pipe I I Minimum 2-1/2' from bottom for branch lines. Minimum 3' from bottom for mainlines. Exception: This requirement shall not apply to 2' or thicker nailing ships resting on top of steel beams. #14 SW Red Nut Driver 1/4' 8018957 SWG 100 1/4x1' 622 (Fir) 25 125J 1/4' 8019957 SWG 200 1/4 x 2" 1725 (Fir) 25 125 8020957 SWG 10 1/4 X1' 622 (Fir) 300 25 125 1 4 , 3/6' 8021957 SWG 20 1/4 x 2' 1725 (Fir) 1050 25 125 3/8 8073925 SWG 20-SS 1/4 x 2 1725 (fy) 850 25 125 _j _[ 3/8' 8022925 SWG 25-380 3/80 2-1/2' 2249 (Fir) 1500 25 125 3) 8023925 SWG 30 114x3 1884 (Fir) - 25 125 j Part #8114910 Insert the appropriate nut driver into a 3/8" or I/2'portable drill. Insert the SAMMYS into the #14 (black) nut driver (p/n 8113910). Drill should be in a vertical position. Push the face of the nut driver fight to the member. When the nut driver spins freely on the SAMMYS, stop drill and remove. The SAMMYS is now ready to receive 1/4", 3/8", 1/2" or metric all thread rod, bolt stock. (The 1/2" requires the #14S W red nut driver) Note: When installing DSTR, follow the above instructions, then add retainer nut and torque to 20 foot lbs. for maximum pullout in purlin steel. Insert the appropriate nut driver into a 3/8' or 1/2' portable drill. Insert the SAMMYS into the #I4SW (red) nut driver (p/n 8114910). With drill unit in a horizontal position and at a right angle to the structural member, begin installation. When the nut driver spins free on the SAMMYS, stop the drill and remove. The unit is now ready to receive 1/4' 3/8" or metric all thread rod or bolt stock. Note: When installing SWDR, follow the above instructions, then add retainer nut and torque to 20 foot lbs. for maximum pullout in purlin steel. SPECIAL NUT DRIVER SYSTEM: The nut drivers were designed with a unique spin-off feature which provides a fast and safe installation each time. When the face of the driver comes into contact with the material you are installing into, continue drilling until nut driver spins free. Installation is then complete. Warranty requires the use of the appropriate nut driver for installations. tqco Fire Protection Products Worldwide www.tyco-fire.com Contacts Series ELO-231 - 112 K-factor Upright and Pendent Sprinklers Standard Response, Standard Coverage General Description TYCO Series ELO-231 11.2K Stan- dard Response, Standard Coverage Upright and Pendent Sprinklers (Ref. Figure 1) are automatic sprinklers of the fusible solder type. They are stan- dard response, spray sprinklers that produce a hemispherical water distri- bution pattern below the deflector. The 11.2 K-factor, ELO-231 Sprinklers were subjected to full scale, high-piled storage, fire tests to qualify their use in lieu of 5.6 or 8.0 K-factor standard spray sprinklers for the protection of high-piled storage. Higher flow rates can be achieved at much lower pressures with the 11.2 K-factor, ELO-231 Sprinklers, making their use highly advantageous in high density applications, such as the pro- tection of high-piled storage. Wax or lead coatings can be used to extend the life of the copper alloy components used in Series ELO-231 sprinklers beyond that which would otherwise be obtained when exposed to corrosive atmospheres. Although wax and lead coated sprinklers have passed the standard corrosion tests of the applicable approval agencies, the testing is not representative of all pos- sible corrosive atmospheres. Conse- quently, it is recommended that the end user be consulted with respect to the suitability of these corrosion resistant coatings for any given corrosive envi- ronment. The effects of ambient tem- perature, concentration of chemicals, and gas/chemical velocity, should be considered, as a minimum, along with the corrosive nature of the chemical to which the sprinklers will be exposed. An upright intermediate level version of the Series ELO-231 Sprinklers for in-rack applications can be obtained by utilizing the Series ELO-231 Upright Sprinkler with the WSG-2 Guard & Shield, and a pendent intermediate level version of the Series ELO-231 Sprinklers can be obtained by utilizing the Series ELO-231 Pendent Sprinkler with the WS-2 Shield. If there is a pos- sibility of the pendent intermediate level version being exposed to mechanical damage, a G-2 Guard can be added. The 11.2 K-factor, Series ELO-231 Upright and Pendent Sprinklers described herein must be installed and maintained in compliance with this document, as well as with the applica- ble standards of the National Fire Pro- tection Association (NFPA), in addition to the standards of any other authori- ties having jurisdiction. Failure to do so may impair the performance of these devices. The owner is responsible for main- taining their fire protection system and devices in proper operating con- dition. Contact the installing contrac- tor or product manufacturer with any questions. Installation of Series ELO-231 Pendent Sprinklers in recessed escutcheons will void all sprinkler warranties, as well as possibly void the sprinkler's Approvals and/or Listings. Sprinkler AN Identification Numbers (SINs) TY5111 - Upright 11.2K, 3/4" NPT 1Y5211 - Pendent 11.2K, 3/4" NPT 1Y5811 - Upright 11.2K, 1/2" NPT TY5111 is a redesignation for Central SIN C5111. TY5211 is a redesignation for Central SIN C5211. TY5811 is a redesignation for Central SIN C5811. IMPORTANT Always refer to Technical Data Sheet TFP700 for the "INSTALLER WARNING" that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and installation can permanently damage a sprinkler system or its compo- nents and cause the sprinkler to fail to operate in a fire situation or cause it to operate prematurely. Page 1 04 JANUARY 2017 TFP34O TFP34O Page 2 of 4 1/2 (12,7 mm) Components: NOMINAL MAKE-IN 1 - Frame 3/4 2 Seal Disc NPT 1 3-Cap 4 - Strut 2-13/16" Assembly (71,4 mm) THREAD - WRENCH 7 5- Compression TYP. FLATS RELIEF 3 Screw 8 6- Deflector* 7- Helper 9 Spring 1/2 3/4" 5 -_ 8 - Ejector NPT NPT _______ Spring L 7/16" (11,1 mm) 1/2 6 9 - Strut Clip (12,7 mm) * Temperature NOMINAL MAKE-IN NOMINAL MAKE-IN rating is UPRIGHT UPRIGHT PENDENT CROSS indicated on TY5811 TY5II1 TY5211 SECTION deflector FIGURE 1 SERIES ELO-231 11.2K UPRIGHT - 3/4" NPT (TY511I), UPRIGHT - 1/2" NPT (TY5811), AND PENDENT - 3/4" NPT (TY5211) SPRINKLERS Technical Data Approvals UL and C-UL Listed FM Approved NYC Approved (Refer to Table A for complete approval information, including corrosion-resis- tant status. The approvals apply to the service conditions indicated in the Design Criteria section.) Maximum Working Pressure 175 psi (12,1 bar) Discharge Coefficient K=11.2 gpm/p5i112 (161,4 pm/bar1!2) Temperature Ratings Refer to Table A Finishes Refer to Table A Physical Characteristics Frame ............................Bronze Seal Disc .........................Copper Cap ..............................Bronze Strut Assembly. Solder, Bronze Stainless Steel Compression Screw .................Bronze Deflector ..........................Bronze Helper Spring ...............Stainless Steel Ejector Spring ......................Nickel Strut Clip ...................Stainless Steel Design Criteria UL and C-UL Listing Requirements TYCO Series ELO-231 11.2K Standard Response, Standard Coverage Upright and Pendent Sprinklers are to be installed in accordance with NFPA 13 standard sprinkler position and area/ density flow calculation requirements for light, ordinary, or extra hazard occu- pancies, as well as high piled storage occupancies (solid piled, palletized, rack storage, bin box, and shelf storage including but not limited to Class I-IV and Group A plastics) with a minimum residual (flowing) pressure of 7 psi (0,5 bar) for wet or dry pipe systems. FM Approval Requirements The 11.2 K-factor, Model ELO-231 (TY5111, TY5211, and TY5811) Sprin- klers are to be installed in accordance with the applicable control mode density/area guidelines provided by FM Global. (FM Approval guidelines may differ from UL and C-UL Listing criteria.) Operation A fusible alloy is sealed into a bronze actuating rod (center strut) by a stain- less steel ball. When the alloy melts at its rated temperature, the ball is forced upward into the center strut, releas- ing the two ejectors and operating the sprinkler. Installation TYCO Series ELO-231 11.2K Stan- dard Response, Standard Coverage Upright and Pendent Sprinklers must be installed in accordance with this section. A leak-tight 3/4 inch NPT sprinkler joint should be obtained by applying a min- imum-to-maximum torque of 10 to 20 lbs.-ft. (13,4 to 26,8 Nm). A leak-tight 1/2 inch NPT sprinkler joint should be obtained by applying a minimum-to- maximum torque of 7 to 14 lbs.-ft. (9,5 to 19,0 Nm). Higher levels of torque can distort the sprinkler inlet with con- sequent leakage or impairment of the sprinkler. "FITTING SIDE" TOWARDS SPRINKLER FITTING /\ WRENCH /RECESS FIGURE 2 W-TYPE 3 SPRINKLER WRENCH Do not attempt to make up for insuf- ficient adjustment in the escutcheon plate by under- or over-tightening the sprinkler. Re-adjust the position of the sprinkler fitting to suit. The Series ELO-231 Upright and Pendent Sprinklers must be installed in accordance with the following instructions: Step 1. Pendent sprinklers are to be installed in the pendent position, and upright sprinklers are to be installed in the upright position. Step 2. With pipe thread sealant applied to the pipe threads, hand tighten the sprinkler into the sprinkler fitting. Step 3. Tighten the sprinkler into the sprinkler fitting using only the W-Type 3 Sprinkler Wrench (Ref. Figure 2), except that an 8 or 10 inch adjustable Crescent wrench is to be used for wax coated sprinklers. With reference to Figure 1, the W-Type 3 Sprinkler Wrench or the adjustable wrench, as applicable, is to be applied to the wrench flats. TFP34O Page 3 of 4 SPRINKLER FINISH SPRINKLER TEMPERATURE FRAME NATURAL CHROME LEAD WAX WAX-OVER-LEAD TYPE RATING COLOR BRASS PLATED COATED COATED COATED 165°F (74°C) Unpainted UPRIGHT 1, 2, 3, 4 (TY5I11&TY5811) 212. F(100.C) White 1,2,3,4 286°F(141°C) Blue 1,2,3,4 1*, 2*, 3* 4* 165°F (74°C) Unpainted (TY5211) PENDENT 1,2,4 1,2,3,4 212-F(100 C) White 286°F(141°C) Blue 1,2,4 1*, 2*, 4* Notes: 3. FM Approved UL Listed 4. Approved by the City of New York (NYC) under MEA 291-04-E c-ui Listed * Listed/Approved for a maximum ceiling temperature of 150'F (66'C) TABLE A 11.2K SERIES ELO-231 UPRIGHT & PENDENT SPRINKLERS, STANDARD RESPONSE LABORATORY LISTINGS AND APPROVALS When installing wax-coated sprinklers with the adjustable wrench, additional care needs to be exercised to prevent damage to the wax coating on the sprinkler wrench flats or frame arms and, consequently, exposure of bare metal to the corrosive environment. The jaws of the wrench should be opened sufficiently wide to pass over the wrench flats without damaging the wax coating. Before wrench-tightening the sprinkler, the jaws of the wrench are to be adjusted to just contact the sprin- kler wrench flats. After wrench-tight- ening the sprinkler, loosen the wrench jaws before removing the wrench.' After installation, the sprinkler wrench flats and frame arms must be inspected and the wax coating re-touched (repaired) whenever the coating has been damaged and bare metal is exposed. The wax coating on the wrench flats can be retouched by gently applying a heated 1/8 inch diameter steel rod to the areas of wax that have been damaged, to smooth it back over areas where bare metal is exposed. Note: Onlyretouching of the wax coating applied to the wrench flats and frame arms is permitted, and the retouching is to be performed only at the time of the initial sprinkler installation. The steel rod should be heated only to the point at which it can begin to melt the wax, and appropriate precau- tions need to be taken, when handling the heated rod, in order to prevent the installer from being burned. If attempts to retouch the wax coating with complete coverage are unsuc- cessful, additional wax can be ordered in the form of a wax stick (the end of which is color coded). Only the correct color-coded wax is to be used, and retouching of wrench flats and frame arms is only permitted at the time of initial sprinkler installation. With the steel rod heated as previously described, touch the rod to the area requiring additional wax with the rod angled downward, and then touch the wax stick to the rod approximately 1/2 inch away from the area requiring retouching. The wax will melt and run down onto the sprinkler. Care and Maintenance TYCO Series ELO-231 11.2K Standard Response, Standard Coverage Upright and Pendent Sprinklers must be main- tained and serviced in accordance with this section. Before closing a fire protection system control valve for maintenance work on the fire protection system that it con- trols, permission to shut down the affected fire protection system must be obtained from the proper authorities and all personnel who may be affected by this action must be notified. Sprinklers that are found to be leaking or exhibiting visible signs of corrosion must be replaced. Automatic sprinklers must never be painted, plated, coated or otherwise altered after leaving the factory. Modi- fied or over-heated sprinklers must be replaced. Care must be exercised to avoid dam-age to the sprinklers before, during, and after installation. Sprin- klers damaged by dropping, striking, wrench twist/slippage, or the like, must be replaced. Frequent visual inspections are rec- ommended to be initially performed for corrosion resistant sprinklers, after the installation has been completed, to verify the long term potential integrity of the sprinkler coatings. Thereafter, annual inspections per NFPA 25 should suffice; however, instead of inspecting from the floor level, a random sampling of close-up visual inspections should be made, so as to better determine the exact sprinkler condition and the long term integrity of the corrosion resistant coating, as it may be affected by the corrosive conditions present. The owner is responsible for the inspection, testing, and maintenance of their fire protection system and devices in compliance with this document, as well as with the applicable standards of the National Fire Protection Asso- ciation (e.g., NFPA 25), in addition to the standards of any other authorities having jurisdiction. Contact the install- ing contractor or product manufacturer with any questions. It is recommended that automatic sprinkler systems be inspected, tested, and maintained by a qualified Inspec- tion Service in accordance with local requirements and/or national codes. TFP34O Page 4 of 4 PIN 50-XXX-X-XXX I I SPRINKLER TEMPERATURE FINISH - - RATING 1 NATURAL 165 165°F (74°C) 6 COATED BRASS WAX 212 212-F (100-C) 7 LEAD COATED 286 286°F (141°C) WAX-OVER-LEAD 8 COATED CHROME PLATED TABLE B SERIES EL0231 11.2K UPRIGHT AND PENDENT SPRINKLERS, STANDARD RESPONSE PART NUMBER SELECTION _L SIN 110 11.2K UPRIGHT (3/4" NPT) TYS111 112 11.2KPENDENT(3/4" NPT) TY5211 210 11.2K UPRIGHT (1/2" NPT) TY2811 Limited Warranty For warranty terms and conditions, visit www.tyco-fire.com. Ordering Procedure Contact your local distributor for avail- ability. When placing an order, indicate the full product name and part number (P/N). Sprinkler Specify: ELO-231 11.2K Standard Response (specify Pendent or Upright) Sprinkler, SIN (specify), temperature rating (specify), with (specify) finish, P/N (specify from Table B) Sprinkler Wrench Specify: W-Type 3 Sprinkler Wrench, P/N 56-895-1-001 Wax Sticks (for retouching wrench-damaged wax coating) Specify: (specify Color) color-coded Wax Stick for retouching (specify temperature rating) temperature- rated Series ELO-231 Sprinklers, P/N (specify): Red for 165°F ................. 56-065-1-155 Blue for 212°F and 286°F ....... 56-065-1 -286 Note: Each wax stick is suitable for retouching up to twenty-five sprinklers. The wax used for 286°F sprinklers is the same as for 212°F sprinklers, and, therefore, the 286°F sprinkler is limited to the same maximum ceiling tempera- ture as the 212'F sprinkler (i.e., 1500F). GLOBAL HEADQUARTERS 11400 Pennbrook Parkway, Lansdale, PA 19446 I Telephone +1-215-362-0700 Copyright © 2017 Tyco Fire Products, LP. All rights reserved. tqco Fire Protection Products tqca Worldwide Fire Protection Contacts www.tyco-fire.com Products Series TY-FRB, 56 K-factor Upright, Pendent, and Recessed Pendent Sprinklers Quick Response, Standard Coverage General Description The TYCO Series TY-FRB, 5.6 K-factor, Upright (TY313) and Pendent (1Y323) Sprinklers described in this data sheet are quick response, standard coverage, decorative 3 mm glass bulb-type spray sprinklers designed for use in light or ordinary hazard, commercial occupan- cies such as banks, hotels, and shop- ping malls. The recessed version of the Series TY- FRB Pendent Sprinkler, where applica- ble, is intended for use in areas with a finished ceiling. This recessed pendent sprinkler uses one of the following: A two-piece Style 15 Recessed Escutcheon with recessed adjust- ment up to 5/8 inch (15,9 mm) from the flush pendent position. A two-piece Style 20 Recessed Escutcheon with recessed adjust- ment up to 1/2 inch (12,7 mm) from the flush pendent position. The adjustment provided by the Recessed Escutcheon reduces the accuracy to which the fixed pipe drops to the sprinklers must be cut. Intermediate level versions of Series TY-FRB Sprinklers are described in Technical Data Sheet TFP357. Sprin- kler guards and shields are described in Technical Data Sheet TFP780. IMPORTANT Always refer to Technical Data Sheet TFP 700 for the "INSTALLER WARNING" that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and installation can permanently dam- age a sprinkler system or its compo- nents and cause the sprinkler to fall to operate in a fire situation or cause it to operate prematurely. Page 1 of 4 NOTICE The TYCO Series TY-FRB Sprinklers described herein must be installed and maintained in compliance with this doc- ument, as well as with the applicable standards of the National Fire Protec- tion Association, in addition to the stan- dards of any other authorities having jurisdiction. Failure to do so may impair the performance of these devices. The owner is responsible for maintain- ing their fire protection system and devices in proper operating condition. The installing contractor or sprinkler manufacturer should be contacted with any questions. Sprinkler Identification Number (SIN) TY313 .......Upright 5.6K, 1/2" NPT TY323 ......Pendent 5.6K, 1/2" NPT Technical Data Approvals UL and C-UL Listed FM, LPCB, and VdS Approved CE Certified Sprinklers with Polyester Finish are UL and C-UL Listed as Corrosion-Resis- tant Sprinklers. Maximum Working Pressure 175 psi (12.1 bar) 250 psi (17.2 bar)* *The maximum working pressure of 250 psi (17.2 bar) only applies to the listing by Un- derwriters Laboratories, Inc. (UL). Discharge Coefficient K=5.6 GPM/psi112 (80,6 LPM/barll2) FEBRUARY 2014 Temperature Rating 135°F (57°C) 155°F (68°C) 175°F (79°C) 200° F (93°C) 286°F (141°C) Finishes Sprinkler: Refer to Table A Recessed Escutcheon: White Coated, Chrome Plated, or Brass Plated Physical Characteristics Frame ...................Bronze Button..............Brass/Copper Sealing Assembly .........Stainless Steel w/TEFLON Bulb ......................Glass Compression Screw........Bronze Deflector.................Bronze TFPI72 TFPI72 Page 2 of 4 Components: 1 - Frame 2 - Button 3 - Sealing Assembly *Temperature rating is ** Pipe thread connections per ISO 7-1 4 - Bulb indicated on Deflector. can be provided on special request. 5 - Compression Screw ESCUTCHEON PLATE 1/2 7/16 (11,1 mm) 6 - Deflector* DEFLECTOR * SEATING SURFACE NPT** NOMINAL MAKE-IN STYLE 15 or 20 RECESSED ESCUTCHEON 1 7/16 (11,1 mm) I NOMINAL MAKE-IN 2" (50,8 mm) 1 1/2 NPT** 2" (50,8 mm) WRENCH FLATS DEFLECTOR * j— 2-7/8" (73,0 mm) DIA. CROSS SECTION UPRIGHT PENDENT RECESSED PENDENT FIGURE 1 SERIES TY-FRB UPRIGHT 'TY313) AND PENDENT (TY323) SPRINKLERS 5.6 K-FACTOR, 1/2 INCH NPT QUICK RESPONSE Operation The glass bulb contains a fluid which expands when exposed to heat. When the rated temperature is reached, the fluid expands sufficiently to shatter the glass bulb, allowing the sprinkler to activate and water to flow. Design Criteria The TYCO Series TY-FRB, 5.6 K-factor, Upright (TY313) and Pendent (TY323) Sprinklers are intended for fire protec- tion systems designed in accordance with the standard installation rules rec- ognized by the applicable Listing or Approval agency (such as, UL Listing is based on the requirements of NFPA 13, and FM Approval is based on the requirements of FM's Loss Prevention Data Sheets). Only the Style 15 or Style 20 Recessed Escutcheon is to be used for recessed pendent installations. Installation The TYCO Series TY-FRB, 5.6 K-factor, Upright (TY313) and Pendent (TY323) Sprinklers must be installed in accor- dance with this section. General Instructions Do not install any bulb-type sprinkler if the bulb is cracked or there is a loss of liquid from the bulb. With the sprin- kler held horizontally, a small air bub- ble should be present. The diameter of the air bubble is approximately 1/16 inch (1,6 mm) for the 135°F (57°C) and 3/32 inch (2,4 mm) for the 2860F (141'C) temperature ratings. A leak-tight 1/2 inch NPT sprinkler joint should be obtained by applying a min- imum to maximum torque of 7 to 14 ft.-lbs. (9,5 to 19,0 Nm). Higher levels of torque can distort the sprinkler Inlet with consequent leakage or impairment of the sprinkler. Do not attempt to compensate for insufficient adjustment in the Escutch- eon Plate by under- or over-tightening the sprinkler. Re-adjust the position of the sprinkler fitting to suit. Upright and Pendent Sprinklers The Series TY-FRB Upright and Pen- dent Sprinklers must be installed in accordance with the following instructions. Step 1. Install Pendent sprinklers in the pendent position. Install upright sprin- klers in the upright position. Step 2. With pipe-thread sealant applied to the pipe threads, hand- tighten the sprinkler into the sprinkler fitting. / WRENCH RECESS / (USE ONLY FIGURE 2 W- TYPE 6 SPRINKLER WRENCH WRENCH RECESS PUSH WRENCH IN TO ENSURE ENGAGEMENT WITH SPRINKLER WRENCHING AREA FIGURE 3 W-TYPE 7 RECESSED SPRINKLER WRENCH TFPI72 Page 3 of 4 Step 3. Tighten the sprinkler into the sprinkler fitting using only the W-Type 6 Sprinkler Wrench (Figure 2). With ref- erence to Figure 1, apply the W-Type 6 Sprinkler Wrench to the wrench flats. Torque sprinklers 7 to 14 ft.-lbs. (9,5 to 19,0 Nm). Recessed Pendent Sprinklers The Series TY-FRB Recessed Pendent Sprinklers must be installed in accor- dance with the following instructions. Step A. After installing the Style 15 or Style 20 Mounting Plate over the sprin- kler threads, and with pipe-thread sealant applied to the pipe threads, hand-tighten the sprinkler into the sprinkler fitting. Step B. Tighten the sprinkler into the sprinkler fitting using only the W-Type 7 Recessed Sprinkler Wrench (Figure 3). With reference to Figure 1, apply the W-Type 7 Recessed Sprinkler Wrench to the sprinkler wrench flats. Torque sprinklers 7 to 14 ft.-lbs. (9,5 to 19,0 Nm). Step C. After ceiling installation and fin- ishing, slide on the Style 15 or Style 20 Closure over the Series TY-FRB Sprin- kler and push the Closure over the Mounting Plate until its flange comes in contact with the ceiling. Care and Maintenance The TYCO Series TY-FRB, 5.6 K-factor, Upright (TY313) and Pendent (TY323) Sprinklers must be maintained and ser- viced in accordance with this section. Before closing a fire protection system main control valve for maintenance work on the fire protection system that it controls, obtain permission to shut down the affected fire protection systems from the proper authorities and notify all personnel who may be affected by this action. Absence of the outer piece of an escutcheon, which is used to cover a clearance hole, can delay sprinkler operation in a fire situation. The owner must assure that the sprin- klers are not used for hanging any objects and that the sprinklers are only cleaned by means of gently dusting with a feather duster; otherwise, non- operation in the event of a fire or inad- vertent operation may result. Sprinklers which are found to be leak- ing or exhibiting visible signs of corro- sion must be replaced. Automatic sprinklers must never be painted, plated, coated, or other- wise altered after leaving the factory. Modified sprinklers must be replaced. Sprinklers that have been exposed to corrosive products of combustion, but have not operated, should be replaced if they cannot be completely cleaned by wiping the sprinkler with a cloth or by brushing it with a soft bristle brush. Care must be exercised to avoid dam- age to the sprinklers before, during, and after installation. Sprinklers damaged by dropping, striking, wrench twist/ slippage, or the like, must be replaced. Also, replace any sprinkler that has a cracked bulb or that has lost liquid from its bulb. (Ref. Installation Section.) The owner is responsible for the inspection, testing, and maintenance of their fire protection system and devices in compliance with this document, as well as with the applicable standards of the National Fire Protection Associa- tion (e.g., NFPA 25), in addition to the standards of any other authorities hav- ing jurisdiction. Contact the installing contractor or sprinkler manufacturer regarding any questions. Automatic sprinkler systems are rec- ommended to be inspected, tested, and maintained by a qualified Inspec- tion Service in accordance with local requirements and/or national codes. 2-7/8 DIA. (73,0 mm) 2-1/4 DIA. FACE OF (57,2 mm) SPRINKLER FITTING 5/8 (15,9 mm) FLUSH 3/8±5/16 (9,5±7,9 mm) MOUNTING/ SURFACE (32 mm) CLOSURE SERIES MOUNTING 1-3/8' (34,9 mm) TYFRB PLATE 3/4' (19,1 mm) FIGURE 4 SERIES TY-FRB RECESSED PENDENT SPRINKLER ASSEMBLY (TY323) WITH TWO PIECE 5/8 INCH TOTAL ADJUSTMENT STYLE 15 RECESSED ESCUTCHEON 2-7/8" DIA. (73,0 mm) FACE OF SPRINKLER 2-1/4" DIA. FITTING (57,2 mm) 5/16±1/4 1/2" (12,7 mm) - MOUNINV#(3,2nmm) ' J I (7,9±6,4 mm) \ FLUSH SURFACE CLOSURE SERIES MOUNTING 1-3/8' (34,9 mm) TYFRB PLATE 7/8" (22,2 mm) FIGURE 5 SERIES TY-FRB RECESSED PENDENT SPRINKLER ASSEMBLY (TY323) WITH TWO PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 20 RECESSED ESCUTCHEON TFPI72 Page 4 of 4 PIN* 77 - XXX - X - XXX SPRINKLER TEMPERATURE FINISH RATINGS SIN 370 5.6K UPRIGHT (1/2 NPT) TY313 371 5.6K PENDENT (1/2 NPT) TY323 Use suffix I" for ISO 7-1 connection; 1 NATURAL BRASS 3 PURE WHITE (RAL9010)°° POLYESTER SIGNAL WHITE (RAL9003) POLYESTER 9 CHROME PLATED for example, 77-370-4-175-I - Eastern Hemisphere sales only 135 135°F(57°C) 155 155°F(68°C) 175 175-F (79-C) 200 200°F (93°C) 286 286°F (141°C) TABLE A SERIES TY-FRB UPRIGHT AND PENDENT SPRINKLERS PART NUMBER SELECTION Limited Warranty For warranty terms and conditions, visit www.tyco-fire.com. Ordering Procedure Contact your local distributor for avail- ability. When placing an order, indicate the full product name and Part Num- ber (P/N). Sprinkler Assemblies with NPT Thread Connections Specify: Series TY-FRB Upright or Pen- dent (specify) Sprinkler, SIN (specify), K=5.6, Quick Response, (specify) tem- perature rating, (specify) finish, P/N (specify, refer to Table A). Recessed Escutcheon Specify: Style 15 Recessed Escutcheon with (specify*) finish, P/N (specify*) Specify: Style 20 Recessed Escutch- eon with (specify*) finish, P/N (specify*) * Refer to Technical Data Sheet TFP770 Sprinkler Wrench Specify: W-Type 6 Sprinkler Wrench, P/N 56-000-6-387 Specify: W-Type 7 Sprinkler Wrench, P/N 56-850-4-001 GLOBAL HEADQUARTERS 11400 Pennbrook Parkway, Lansdale, PA 19446 I Telephone +1-215-362-0700 Copyright© 2014 Tyco Fire Products, LP. All rights reserved. tqco TEFLON is trademark of The DuPont Corporation. Fire Protection Products I Malleable Iron Threaded Pipe Unions Pressure - Temperature Ratings Temperature Pressure Class 150 Class 250 Class 300 (°F) (°C) psi bar psi bar psi bar 2O0 to 1500 -28.9° to 300 65.60 20.7 500 34.5 600 41.4 2000 93.30 265 18.3 455 31.4 550 37.9 2500 121.10 225 15.5 405 27.9 505 34.9 3000 148.90 185 12.8 360 24.8 460 31.7 3500 176.70 150 10.3 315 21.7 415 28.8 4000 204.40 110 7.6 270 18.6 370 25.5 4500 232.20 75 5.2 225 15.5 325 22.4 5000 260.00 - - 180 12.4 280 19.3 5500 287.80 - - 130 9.0 230 15.3 Note: Unions with Copper or Copper Alloy seats are not intended for use where tampwatjre exce ads 450°F C(@ US <:~~> APPROVED For Listings/Approval Details and Limitations, visit our webs te @ www.anvilintl.com or contact an Anvil/AnvilStar Sales Representativ3. Malleable Iron Threaded Fittings Pressure - Temperature Ratings Temperature Pressure Class 150 Class 300 __________ Sizes '/4'-1" (6-25 mm) Sizes 1/4"_9" (32-E1 mm) Sizes 2,4-3' (64-76 mm) (°F) (°C) psi br psi bar psi bar psi bar -200 to 1500 -28.90 to 300 207 2,000 65.60 137.9 1,500 105.4 1,000 68.9 2000 93.3 265 183 1,785 123.1 1,350 93.1 910 62.7 2500 121.1 225 155 1,575 108.6 1,200 82.7 825 56.9 3000 148.9 185 128 1,360 93.8 1,050 72.4 735 50.7 3500 176.7 150 103 1,150 79.3 900 62.1 650 44.8 4000 204.4 - - 935 64.5 750 51.7 560 38.6 4500 232.2 - - 725 50.0 600 41.4 475 32.8 5000 260.0 - - 510 35.2 450 31.0 385 26.5 5500 287.8 - - 300 20.7 300 20.7 1 300 20.7 Anvil Class 150/300 Malleable Iron Fittings conform to ASME B16.3 and Unions conform to ASME B16.39. ALL ELBOWS & TEES 3/' (0 ON) and LARGER ARE - 00% GAS TESTED AT A MINIMUM OF 100 PSI. (6.9 bar) www.anvuintl.com " 17 TO C. çhe best sprinkler in the industry! c®us LISTED <> APPROVED NO 4 ONf4 NFPA BULL MOOSE TUBE COMPANY =K§PJ MJ kVA ull Moose Tube® is a customer focused, growth oriented manufacturer and marketer of tubular products, where success is based on a commitment to meeting the customer's perception of quality. Our strength resides in our people working together to satisfy customers and to promote business growth by achieving superior financial performance. c®us LISTED www.BullMooseTube.com sales@bullmoosetube.com 800.325.4467 <*> APPROVED Mo4 NFPA =° BULL IV100SE TUBE COMPANY Bull Moose Tube's® "Eddy Pipe®" brand sprinkler pipe is produced to meet sprinkler pipe standards and applications. c®us LISTED <*> APPROVED I;] 4 NFSA NFPA ADVANTAGES OF BULL MOOSE TUBE® EDDY PIPE® FAMILY All pipe products are UL Listed (for U.S. and Canada), and have been approved by Factory Mutual. Excellent production and coating capabilities, tighter tolerances, and our unique steel properties make our pipe excellent for roll grooving, welding, threading, and plain end fittings. All products are certified to ASTM Al 35 and A795 Type E, Grade A. Available in specific cut to order lengths from regular mill rollings. More popular sizes available with coating or bare. Ultra Eddy®, Eddy Flow®, Eddylite®, and Eddythread 40® offer cost savings along with superior hydraulics without compromising service life. Sprinkler pipe inventory stocked in Masur Ohio; Gerald, Missouri; Casa Grande, Arizona; Kent, Washington; and Dallas, Texas. All Bull Moose (black) sprinkler pipe includes our exclusive EDDY GUARD Il® MIC preventative coating. Bull Moose Tube® sprinkler pipe is FBCTM compatible. PRODUCTS Schedule 10 and Schedule 40: FM approved and UL listed sprinkler pipe. Eddythread 40®: Light threadabte Schedule 40 replacement with corrosion resistance ratio of 1.0. Eddylite®: Liqhtwall threadable with standard outside diameter. Eddy Flow®: Cost effective replacement for Schedule 10. Ultra Eddy®: Lightwall roll groovable pipe. Bull Moose galvanized steel sprinkler pipe is hot dipped galvanized to meet ASTM Al 23 standards. All products are stencilled to meet FM & UL specifications. PROTECTION Eddy Guard Il®: Bull Moose Tube® is producing product that can resist bacteriological growth even after multiple rinse-outs. You know MlC corrosion can impact your installation and your property. Specify Bull Moose Tube® "Eddy Guard Il®" and feel comfortable knowing that you are getting Eddy Pipe® product you trust with the bacteria resistance you need. Eddy Guard Il® is NFPA 13 and NFPA 13R system compatible for use in hybrid systems as well as FM approved. All information contained herein is accurate as known at the time of publication. Bull Moose Tubes reserves the right to change product specifications without notice and without incurring obligation. Ll LI El c®us LISTED <> APPROVED C;] 4 ONFSA NFPA SP,•A,,,e.ic*nFfr. SCHEDULE 10 PIPE SPECIFICATIONS NOMINAL PIPE O.D. I.D. WATER FILLED BUNDLE SIZE (IN) (IN) (IN) CRR** WEIGHT/FT WEIGHT SIZE 1 J1 1.315 - 1.097 1527 - 1.41 lbs/ft 1.820 91 - lE 9.911-K 1-81 Ibft1[ 251ifl61 1 11/2 1.900 1682 - L 2 11[ 2375 ]L -- 2.157 JL 627 j[264iLiifrr4223 1 _ 2-1/2 2.875 17_2.635 ' 492 —3.53 1 bs/ff 5.893 30 r_3500 1[_3260 ]E_3541ftL_19 1 - 4 I[ 4500 -4 2-60 250 - 562 lbs/ft _11-796— 19 — SCHEDULE 40 PIPE SPECIFICATIONS NOMINAL PIPE O.D. I.D. WATER FILLED BUNDLE SIZE (IN) (IN) (IN) CRR** WEIGHT/FT WEIGHT SIZE 1.315 1 1.049 ioo 168lbs/ft _2.055 70 1 1660 11 1.380 ]El00 J[27liff]L 2918 11 51 11 19OO 1610 100 __2_J2 1bs/ft 3602 1 2 2.375—=] 1 2067 J -3-6If( 5.114 j[ 30 1 2l*L2j2468 100 580ths/ —7.- 875 30 — LIi3 iI1 L_3_500 _[ _3_068 1 LII = -7.58 1 _19 4* 4.500 4.026 1.00 10.80 lbs/ft 16.316 19 *Only available in Casa Grande, AZ —Corrosion Resistance Ratio per latest UL Directory Listing PIPE PREPARATION For proper operation, all pipe surfaces should be cleaned prior to installation. In order to provide a leak-tight seat for the gasket, pipe surfaces should be free from indentations and projections from the end of the pipe to the groove. All loose paint, scale, dirt, chips, grease, and rust must be removed prior to installation. Failure to take these important steps may result in improper coupling assembly, causing leakage. Also, check the manufacturer's instructions for the specific fitting used. For Additional Information Contact (800) 325-4467 www.bulImoosetube.com Or From Canada Call: (800) 882-4666 sales@buIlmoosetube.com 1819 Clarkson Road Chesterfield, MO Gerald, MO Kent, WA Casa Grande AZ Dallas, D( Masur OH BULL IVICOSE TUBE CDMPAI'4V 63017 Bull Moose Tube's® Schedule 10 and Schedule 40 are FM Approved and UL Listed (for U.S. and Canada), even though these products do not require separate approvals and listings. Bull Moose Tube® made the decision to have them approved and listed. Our Schedule 10 and Schedule 40 have a pressure rating of 300 PSI and have been through the same rigorous testing as our other fine pipe products. Schedule 10 can be supplied roll grooved or plain end. Bull Moose Tube's® Schedule 10 and Schedule 40 pipes are hot dipped galvanized to meet ASTM Al 23 standards. All products are stencilled to meet FM & UL specifications. I FireLock® Outlet-T STYLE 922 ® ILPCBI SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS The Style 922 Outlet-T provides a convenient method of incorporating ½, 3/4, and 1/15, 20 and 25mm outlets for directly connecting sprinklers, drop nipples, sprigs, gauges, drains and other outlet products. Available for 1V4 through 76.1 mm/32 to 76.1 mm piping systems, Style 922 outlets are UL/ULC Listed, LPCB and FM Approved for branch connections and VdS Approved for direct sprinkler connection only on wet and dry systems. The locating collar engages into the hole prepared in the pipe. When tightened, the assembly compresses the gasket onto the OD of the pipe. The Style 922 Outlet-T is UL/FM rated up to 300 psi/2068 kPa and VdS rated up to 16 bar at the ambient temperatures typical for fire protection systems. Style 922 is suitable for use on standard, lightwall, Schedule 5 and other specialty pipes.* Contact Victaulic for other optional coatings. *consult Section 10.01 for specific listings/approvals. MATERIAL SPECIFICATIONS Housing: Ductile iron conforming to ASTM A-536, grade 65-45-12. Ductile iron conforming to ASTM A-395, grade 65-45-15, is available upon special request. Gasket: Grade "E" EPDM - Type A (Violet color code). FireLock products have been Listed by Underwriters Laboratories Inc. and Approved by Factory Mutual Research for wet and dry (oil free air) sprinkler services up to the rated working pressure using the Grade "E" Type A Gasket System. Bolts/Nuts: Heat-treated plated carbon steel, trackhead meeting the physical and chemical requirements of ASTM A-449 and physical requirements of ASTM A-183. Housing Coating: Orange enamel (North America, Latin America, Asia Pacific) Red enamel (Europe) JOB/OWN ER CONTRACTOR ENGINEER System No. Submitted By Spec Sect Para Location - Approved www.victaulic.com VICTAIJLIC IS REGISTERED TRADEMARK OF vIcTAUUC COMPANY. © 2009 vIcTAULIC COMPANY. ALL RIGHTS RESERVED. REV ( JtauIicr 10.52 1 STYLE 922 DIMENSIONS rem 'am '.19 PS CARBON STEEL PIPE - ROLE CUT PRODUCTS FireLock® Outlet-I Nominal Size H 0 le inches/mm Diameter Dimensions - inches/millimeters Approx. Weight Each 77771 Run 1¼ ½ / 16 130 183 110 387 256 10 x 32 15 302 330 465 279 98.3 65.0 0.45 3/4 1 3A6 1.28 183 110 387 2.56 1.1 20 30.2 32.5 46.5 27.9 98.3 65.0 0.50 1 13/16 1.52 2.18 1.10 3.87 - 2.56 1.2 25 30.2 38.6 55.4 27.9 98.3 65.0 0.54 11/2 ½ 13/16 1.42 1.95 1.22 4.08 2.56 1.2 x 40 15 30.2 36.1 49.5 31.0 103.6 65.0 054 3/4 1/I6 1.40 1.95 1.22 4.08 2.56 1.2 20 30.2 35.6 49.5 31.0 103.6 65.0 0.54 13A6 1.64 2.30 1.22 4.08 2.56 1.3 25 30.2 41.7 58.4 31.0 103.6 65.0 0.59 2 1/ 13A6 1.66 2.19 1.46 4.60 2.56 1.3 x 50 is 30.2 42.2 55.6 37.1 116.8 65.0 0.59 34 13/16 1.64 2.19 1.46 4.60 2.56 1.4 20 30.2 41.7 55.6 37.1 116.8 65.0 0.64 1 13/16 1.88 2.54 1.46 4.60 2.56 1.5 25 30.2 47.8 64.5 37.1 116.8 65.0 0.68 2½ ½ iI 16 1.91 2.44 1.71 5.40 2.56 1.6 x 65 15 30.2 48.5 62.0 43.4 137.2 65.0 0.73 '/4 1/16 1.89 2.44 1.71 5.40 2.56 1.6 20 30.2 48.0 62.0 43.4 137.2 65.0 0.73 1 13/16 2.13 2.79 1.71 5.40 2.56 1.6 25 30.2 54.1 709 43.4 137.2 65.0 0.73 ½ 13A6 1.91 2.44 1,71 5.50 2.56 1.6 76.1 mm X 15 30.2 48.5 62.0 1 43.4 139.7 65.0 0.73 '/4 1/l6 1.89 2.44 171 5.50 2.56 1.6 20 30.2 48.0 62.0 43.4 139.7 65.0 0.73 1 1 3A6 2.13 2.79 1.71 5.50 2.56 1.7 25 30.2 1 54.1 70.9 43.4 1 139.7 1 65.0 0.80 t Victaulic female threaded products are designed to accommodate standard NFl or BSPT (optional) male pipe threads only. Use of male threaded products with special features, such as probes, dry pen- dent sprinklers, etc., should be verified as suitable for use with this Victaulic product. Failure to verify suitability in advance may result in assembly problems or leakage. Center of run to engaged pipe end for NPT threads (dimensions are approximate), www.victaulic.com VICTAULIC IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2009 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 10.52 2 \4tauIic REV ( IPS. CARBON STEEL PIPE- HOLE CUT PRODUCTS FireLock® Outlet-I STYLE 922 PERFORMANCE Run Size x Outlet Size Equivalent Length of 1 inch Schedule 40 Steel Pipe (per UL 213, Section 16) (C=120)*, FT Inches/mm $TJA I Feet/meter 32 25 so 25 - 21/2 1 .. 65 2S lulrlal.u1ii.. * Hazen-Williams coefficient of friction is 120 www.victaulic.com A_Cta_uhln~ VICTAULIC ISA REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2009 VICTAULIC COMPANY. ALL RIGHTS RESERVED. IFV r 10.52 FireLock® Outlet-I STYLE 922 INSTALLATION Reference should always be made to the 1-100 Victaulic Field Installation Handbook for the product you are installing. Handbooks are included with each shipment of Victaulic products for complete installation and assembly data, and are available in PDF format on our website at www.victaulic.com. WARRANTY Refer to the Warranty section of the current Price List or contact Victaulic for details. NOTE This product shall be manufactured by Victaulic or to Victaulic specifications. All products to be installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations. For complete contact information, visit www.victaulic.com 10.52 3355 REV G UPDATED 12/2009 Aat-aulic~ vIcTAuUc IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2009 VIcTAULIC COMPANY. ALL RIGHTS RESERVED. 10.52 P.O. Box 3365 South El Monte, CA 91733 626.444.0541 Fax 626.444.3887 www. Afcon.org 300 RING HANGER I thru 4 inch pipe LISTED FOR STEELJCPVC 1/2 & 3/4 inch pipe 5 thru 8 inch pipe SIZE - ROD- 3/8" or 1/2" SIZE - SYSTEM PIPE - 1/2" thru 8" MATERIAL - Carbon Steel, Mil. Galvanized to G-90 spec. LISTING/APPROVAL - c@ us LISTED 203-EX 25511"- 8" Approval guide - 1"- 8" OSHPD OPA-0601 See Website. CONFORMS WITH: Federal Specification WW-H-171E, Type 10. Manufacturers Standardization Society ANSI/MSS-SP-58 Type 10. MAXIMUM TEMPERATURE - 650°F. FUNCTION - Pipe hanger component of an AFCON hanger. To support steel, CPVC or copper pipe. INSTALLATION - Per NFPA 13, 13R, 13D, these instructions and the CPVC or copper pipe manufacturers instructions. FEATURES - * Sized and listed exclusively for use with #310 Surge Restrainer. * Band edge is offset for EASY pipe insertion. * Custom fit swivel nut for better retention in ring. ORDERING - Part #, pipe size. 11/09 NFPAI3 PIPE ROD I WT. 5 WT.+250 UL TEST LOAD 1 3/8 3075 403.75 750 11/4 3/8 43.95 46975 750 11/2 3/8 54.15 520.75 750 2 3/8 76.95 634.75 750 21/2 3/8 118.35 841.75 850 3 1 3/8 162.30 1061.50 1050 4 3/8 246,00 1480.00 1500 5 1/2 349.45 1996.75 2000 B 1/2 476.35 2631.75 2650 8 1/2 711.00 1 3805.00 4050 Restraint SIZE - One size fits 3/4 thru 2 inch AFCON #300 Ring Hanger. 551 P.O. Box 3365 South El Monte, CA 91733 626.444.0541 Fax 626.444.3887 www. Afcon.org 310 RING RESTRAINER MATERIAL - Carbon Steel. FINISH - Mil. Galvanized. LISTINGS - 4— c us 203-EX 2551 Listed only for use with AFCON #300 Ring Hanger. FUNCTION - To restrain movement of sprinkler pipe toward the knurl nut of the ring hanger. To prevent upward movement of pipe that supplies a pendent sprinkler below the ceiling. INSTALLATION - Per NFPA 13 and CPVC manufacturers instructions on steel, CPVC, or copper pipe. Snap into locking position on swivel nut of AFCON #300 Ring Hanger. SPECIAL NOTE: When installing on CPVC sprinkler system pipe: Verify that all assembly components are cleaned of any surface oil. FEATURES - * Listed only for use with AFCON #300 Ring Hanger. ORDERING - Part # and size. Specific AFCON products are exclusively designed to be compatible ONLY with other AFCON products including parts and fasteners, resulting in a listed sway brace, restrainer or hanger assembly. Be advised the following warranty restriction will apply. DISCLAIMER - AFCON will NOT warrant against the failure of its products when used in combination with other products, parts or systems not manufactured or sold by AFCON. AFCON shall NOT be liable under any circumstances whatsoever for any direct or indirect, incidental or consequential damages of any kind, including but not limited to loss of basiness or profit, when non-AFCON products have been, or are used. Id 1/08 Not less than Wood Flooring Product Features No pre-drilling required. Quick to install using the Sammy Nut Driver with an 18V cordless drill/driver. Saves time from traditional methods. Reduces installation cost. Made in the U.S.A. 141 8002957 GST 100 114x1" 210 670 25 125 1/4" 8003957 GST 200 1/4x2" 1760 (Fir) 25 125 i oB:vCeI Part #8113910 I - 1/4 8004957 GST 300 1/4x3" 2060 (Fir) 25 125_J 3/8" 8006957 GST .75 1/4x 3/4 564 (3/4" Ply) 25 125 [_1 3/8" 8007957 GST 10 1/4 x1" 210 (7116" OSB) 300 25 125 3/8"8008957 GST 2O1/4x2"1760(Fir)850 147525 125 3/8__8068925_ GST 2ÔS1/x 2__1760 ( _850 25125 1 3/8" 8009925 GST 25-380 3/8x2-112" 2113 (Fir) 1500 25 125 -3/8_8010957 GST 301/4 x 3_2060(Fir 1500147525125 1 ) 3/8" 8069925 GST 30-SS1/4x3" 2060 (Fir) 25 125 I 3/8 8011 GST 40 1/44 2180(Fir) 25 125 1 3/8" 8012925 GST 60 1/4x6 2230 (Fir) 25 125 - I_1/2"8013925 GST 2 1/4x2"1760(Fir)25125 7 #14SWRed 1/2" 8014925 GST 2.5-380 3/8 x 2-1/2" 2113 (Fir) 25 125 I_1/2_8015925 GST 3 1/4x3__2275(Fir)25125__j 1/2" 8016925 GST4 1/4x4" 2180 (Fir) 25 125 I jJ 8017925 GST6 1/4x6" 2230 (Fir) 25 125 1 - Nut Driver Part #8114910 Product Features Eliminates distortion of threaded rod. • Saves time from traditional methods. Accommodates up to 3 W' / x 12 pitch roof. • Reduces installation cost. "Allows 17" deflection from vertical. • Made in the U.S.A. 3/8" 8139957 SH.GST20 1/4x2 1257 (Fir) 1050 1475 25 125 3/8" 8141957 SH-GST30 1/4x3" 1720 (Fir) 1500 1475 25 125 SPECIAL NUT DRIVER SYSTEM: The nut drivers were designed with a unique spin-off feature which provides a fast and safe installation each time. When the face of the driver comes into contact with the material you are installing into, continue drilling until nut driver spins free. Installation is then complete. Warranty requires the use of the appropriate nut driver for installations. #14 Black Nut Driver Part #8113910 Fir 1/4' 1/4x1' 522 (Fir) 25 1/4' 8019957 SWG 200 1/4 x 2" 1725 (Fir) 25 125 3/8' 8020957 SWG 10 - 114x1' 622 (Fir) - aoo 25 4, 3/8' 8021957 SWG 20 1/4x2' 1725 (Fir) 1050 25 125 /R' Rfl7Q7S SW 9 . 1/402' 1725 (Fir) 850 25 125 1 €l 3/8 8022925 SWG 25380 3/8021/2 2249 (Fir) 1500 25 125 I #14 SW Red Nut Driver Part # 8114910 Product Features No pre-drilling required. 'Quick to install using the Sammy Nut Driver with an 18V cordless drtllldriver. 'Saves time from traditional methods. 'Reduces installation cost 'Made in the U.S.A. Not less than 2' nominal width (1.1/2') up to 3-1/2' pipe; not less than 3' (2-1/2') nominal width 4' & 5' pipe 4 A Minimum 2-1/2' from bottom for branch lines. Minimum 3' from bottom for main lines. Exception: This requirement shall not apply to 2' or thicker nailing stops resting on top of steel beams. j IV Ii IN Floor Joist Insert the appropriate nut driver into a 3/8" or 1/2" portable drill Insert the SAMMYS into the #14 (black) nut driver (p/n 8113910). Drill should be in a vertical position. Push the face of the nut driver tight to the member. When the nut driver spins freely on the SAMMYS, stop drill and remove. The SAMMYS is now ready to receive 1/4", 3/8", 1/2" or metric all thread rod, bolt stock. (The 1/2" requires the #14S W red nut driver) Note: When installing DSTR, follow the above instructions, then add retainer nut and torque to 20 foot lbs, for maximum pullout in purl/n steel. Insert the appropriate nut driver into a 3/8" or 1/2" portable drill. Insert the SAMMYS into the #I4SW (red) nut driver (pIn 8114910). With drill unit in a horizontal position and at a right angle to the structural member, begin installation. When the nut driver spins free on the SAMMYS, stop the drill and remove. The unit is now ready to receive 1/4", 3/8" or metric all thread rod or bolt stock. Note: When installing SWDR, follow the above instructions, then add retainer nut and torque to 20 foot lbs. for maximum pullout in puffin steel. SPECIAL NUT DRIVER SYSTEM: The nut drivers were designed with a unique spin-off feature which provides a fast and safe installation each time. When the face of the driver comes into contact with the material you are installing into, continue drilling until nut driver spins free. Installation is then complete. Warranty requires the use of the appropriate nut driver for installations. FIRE SPRINKLER CORPORATION S1dAIVDARD RESPONSE AUTOMATIC SPRINKLERS GL SERIES UPRIGHT s PENDENT VERTICAL SIDEWALL HORIZONTAL SIDEWALL CONVENTIONAL (OLD STYLE) DESCRIPTION AND OPERATION The Globe Standard Response Series GL-SR Sprinklers are a low profile yet durable design which utilizes a 5mm frangible glass ampule as the thermosensitive element.. While the Standard j/ \ Response Sprinkler provides an aesthetically pleasing appear- ance, it can be installed wherever standard spray sprinklers are specified when allowed by the applicable standards. It offers the additional feature of greatly increased safety to life and is available in various styles, orifices, temperature ratings and fin- ishes to meet varying design requirements. Standard Response STANDARD RESPONSE Sprinklers should be used advisedly and under the direction of SERIES GL-SR SERIES GLSRICNV approving authorities having jurisdiction. UPRIGHT CONVENTIONAL The heart of Globe's Series CL-SR sprinkler proven actuat- ing assembly is a hermetically sealed frangible glass ampule that contains a precisely measured amount of fluid. When heat is absorbed, the liquid within the bulb expands increasing the . internal pressure. At the prescribed temperature the internal pressure within the ampule exceeds the strength of the glass + causing the glass to shatter. This results in water discharge which is distributed in an approved pattern depending upon the deflector . style used. STANDARD RESPONSE The sprinkler and escutcheon are not factory assembled. SERIES GL-SR SERIES GL-SR/SW Assembly is done in the field. PENDENT VERTICAL - -- ._•. SIDEWALL I ECHNICAL Lh4TA See reverse side for Approvals and Specifications. Temperature Ratings - 135°F (57°C), 155°F (68°C), _ 175°F (79°C), 200°F (93°C), 286°F (141°C), 360°F (182°C) 500°F (26000) Available Upon Request Without Approvals Water Working Pressure Rating -175 psi (12 Bars) Factory tested hydrostatically to 500 psi (34 Bars) STANDARD RESPONSE Maximum low temperature glass bulb rating is -67°F (-55°C) SERIES GL-SR/SW SERIES GL-SR/SW Frame - bronze • Deflector - brass Screw - brass LPCB/CE HORIZONTAL Lodgement Wire - stainless steel • Bulb seat - copper HORIZONTAL SIDEWALL Spring - nickel alloy Seal - teflon SIDEWALL Bulb - glass with glycerin solution, 5mm size Escutcheon Assembly - steel -SPRINKLER TEMPERATURE RATING/CLASSIFICATION and COLOR CODING CLASSIFICATION AVAILABLE SPRINKLER TEMPERATURES BULB COLOR N.F.P.A. MAXIMUM CEILING TEMPERATURE ORDINARY i35°F155F 5C )68C ORANGE/RED 1OOF INTERMEDIATE HIGH 175°[/2&O+F 1*9 C93 FQØ + YELLOW/GREEN BLUE 15OF+u+ 66 ".+c EXTRA HIGH 36UE ULTRAHIGH MAUVE 300T 149C BLACK MAR 2018 GFS-100b (Formerly A-65) 1TA NDA RD RESPONSE A UTOMA TIC SPRINKLERS SERIES GL-SR UPRIGHT • PENDENT VERTICAL SIDEWALL HORIZONTAL SIDEWALL CONVENTIONAL (OLD STYLE) SPECIFICATIONS NOMINAL "K" FACTOR THREAD SIZE LENGTH' FINISHES 2.8 (40 metric) 1/2"NPT (15mm) 2 1/4" (5.7cm) Factory Bronze 4.2 (60 metric) 1/2"NPT (15mm) 2 1/4" (5.7cm) Chrome 5.6 (80 metric) 1/2"NPT (15mm) 2 1/4" (5.7cm) White Polyester' 8.0 (115 metric) 1/2"NPT(l5mm) 2 1/4" (5.7cm) Black Polyester23 8.0 (115 metric) 3/4"NPT (20mm) 2 7/16" (6.2cm) Wax Coated23'4 NOTE: METRIC CONVERSIONS ARE APPROXIMATE. 'AVAILABLE AS cULus LISTED CORROSION RESISTANT WHEN SPECIFIED ON ORDER. 1HORIZONTAL SIDEWALL IS 29/16". :AVAILABLE COATING cULus LISTED UP TO 200°F (93°C) ONLY. 'FINISHES AVAILABLE ON SPECIAL ORDER. LISTINGS/APPROVALS TEMPERATURE STYLE SIN FACTOR HAZARD' cULus FM LPCB' CE MEAIOI-92-E 135°F 155°F 175°F 200°F **286F "360°F (57°C) (68°C) (79°C) (93°C) (141°C) (182°C) GL2861 2.8 LI-I X X X X X X X --- --- --- X GL4261 4.2 LI-I X X X X X X X --- --- X UPRIGHT GL5661 5.6 ALL X X X X X X X X X X X GL8161° 8.0- (1/2" NPT) ALL X X X X X X X --- --- --- X GL8164 8.0 ALL X X X X X X X X X X X GL2851 2.8 LH X X X X X X X --- --- --- X GL4251 4.2 LH X X X X X X X --- --- --- X PENDENT GL5651 5.6 ALL X X X X X X X X X X X GL8151° 8.0°(W NPT) ALL X X X X X X X --- --- --- X GL8156 8.0 ALL X X X X X X X X' X X X VERTICAL GL5675 5.6 LH X X X X X X X X SIDEWALLt GL8176 8.0 LH X X X X X X X GL2870 2.8 LH X X X X X X X --- --- --- x TA GL4270 4.2 [H X X X X X X X --- --- --- X HORIZONTAL SIDEWALL GL5670 5.6 LH/OH X X X X X X X X --- --- X GL5671D 5.6 LH/OH X X X X X X --- --- X X GL8171 8.0 LH/OH X X X X X X X --- CONVENTIONAL GL5668 5.6 LH/OH X X X X X X --- --- X X (OLD STYLE) GL8169 8.0 LH/OH X X X X X X --- --- --- x 'SPRINKLERS SHALL BE LIMITED AS PER 'rHE REQUIREMENTS OF NFPA1 3 AND ANY OTHER RELATED DOCUMENTS. 'BRASS FINISH ONLY WHEN RECESSED §HORIZONTAL SIDEWALL cULus LISTED FOR DEFLECTOR 4" TO 12" BELOW THE CEILING, FM APPROVED 4" TO 6" BELOW THE CEILING. **NO FM APPROVALS FOR RECESSED INSTALL IN ACCORDANCE TO B55306 AND ANY OTHER RELATED DOCUMENTS. "NO FM APPROVALS tPENDENT VERTICAL SIDEWALL cULus LISTED FOR 6' MIN. SPACING. OH: ORDINARY HAZARD tUPRIGHT VERTICAL SIDEWALL cULus LISTED FOR 9' MIN. SPACING. LH: LIGHT HAZARD 500"F (260°C) AVAILABLE UPON REQUEST WITH NO APPROVALS. ALL: ALL HAZARDS °1/2"NPT; RETRO-FIT ONLY 'LPCB REF. NO. 147c/04 ORDERING INFORMATION SPECIFY Quantity SLN• Style Orifice Thread Size Temperature Finish desired Quantity - Wrenches/Recessed Wrenches - P/N 325390/325391 (1/2"); P/N 312366/325401 (L.O.) Quantity Protective Caps - P/N 327109-CAP (Friction Fit Recessed) GLBE FIRE SPRINKLER CORPORATION MAR 2018 GLOBE® PRODUCT WARRANTY Globe agrees to repair or replace any of its own manufactured products found to be defective in material or workmanship for a period of one year from date of shipment. For specific details of our warranty please refer to Price List Terms and Conditions of Sale (Our Price List). 4077 AIRPARK DRIVE, STANDISH, MICHIGAN 48658 989-846-4583 FAX 989-846-9231 1-800-248-0278 www.globesprinkler.com PRINTED U.S.A. GFS-100b (Formerly A-65)