Loading...
HomeMy WebLinkAbout2510 EL CAMINO REAL; ; AS160297; Permit4/6/2021 AS160297 Permit Data City of Carlsbad Sprinkler Permit Permit No: AS160297 2510 EL CAMINO Job Address: REAL Permit Type: SPRINK Parcel No: 1670305000 Status: ISSUED Applied 9/15/2016 Approved: 9/21/2016 Lot #: 0 Reference No.: Issued: 9/21/2016 PC Inspector: Project Title: CVS #9479 RELOCATE TO EXISTING PENDENT SPRINKLERS WITH NEW LIKE KIND AND ADD (3) NEW LIKE KIND UPRIGHT SPRINKLERS TO AN EXISTING WET AUTOMATIC FIRE SPRINKLER SYSTEM FOR A PHARMACY REMODEL. Applicant: RBM FIRE PROTECTION 23597 ANCASH CT PERRIS, CA 951-657-8899 Owner: VONS COMPANIES INC A A E PACIFIC PARK ASSCS C/O HUGHES INVESTMENTS-MANAGER P 0 BOX 8700 NEWPORT BEACH CA Fees ($) Add'I Fees ($) Total ($) Balance ($) 378 0 378 0 1/1 Fire Protection Products Worldwide www.tyco-fire.com Contacts I Series TY-L - 56 and 8.0 K-factor Upright, Pendent, and Recessed Pendent Sprinklers Standard Response, Standard Coverage General Description The TYCO Series TY-L, 5.6 and 8.0 K-factor, Upright, Pendent, and Recessed Pendent Sprinklers described in this data sheet are stan- dard response, standard coverage, solder type spray sprinklers designed for use in light, ordinary, and extra hazard, commercial occupancies such as banks, hotels, shopping malls, fac- tories, refineries, chemical plants, etc. The recessed version of the Series TY-L Pendent Sprinkler, where appli- cable, is intended for use in areas with a finished ceiling. It uses a two-piece Style 20 (1/2 inch NPT) or Style 30 (3/4 inch NPT) Recessed Escutcheon. The Recessed Escutcheon provides 1/4 in. (6,4 mm) of recessed adjustment or up to 1/2 in. (12,7 mm) of total adjustment from the flush pendent position. The adjustment provided by the Recessed Escutcheon reduces the accuracy to which the fixed pipe drops to the sprin- klers must be cut. Corrosion resistant coatings, where applicable, are utilized to extend the life of copper alloy sprinklers beyond that which would otherwise be obtained when exposed to corrosive atmo- spheres. Although corrosion resistant coated sprinklers have passed the standard corrosion tests of the appli- cable approval agencies, the testing is not representative of all possible cor- rosive atmospheres. Consequently, it is recommended that the end user be consulted with respect to the suit- ability of these coatings for any given IMPORTANT Always refer to Technical Data Sheet TFP 700 for the "INSTALLER WARNING" that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and installation can permanently damage a sprinkler system or its compo- nents and cause the sprinkler to fail to operate in a fire situation or cause it to operate prematurely. Page 1 of 6 corrosive environment. The effects of ambient temperature, concentration of chemicals, and gas/chemical velocity, should be considered, as a minimum, along with the corrosive nature of the chemical to which the sprinklers will be exposed. An intermediate level version of the Series TY-L Pendent Sprinkler can be obtained by utilizing the Series TY-L Pendent Sprinkler in combination with the Model S Shield. The TYCO Series TY-L, 5.6 and 8.0 K-factor, Upright and Pendent Sprin- klers described herein must be installed and maintained in compliance with this document, as well as with the applicable standards of the National Fire Protection Association, in addition to the standards of any other authori- ties having jurisdiction. Failure to do so may impair the performance of these devices. The owner is responsible for main- taining their fire protection system and devices in proper operating con- dition. Contact the installing contrac- tor or product manufacturer with any questions. Sprinkler Identification Number (SIN) TY3111 ......Upright 5.6K, 1/2" NPT TY3211 .. . . Pendent 5.6K, 1/2" NPT TY4111 .....Upright 8.01K, 3/4" NPT TY4211 .....Pendent 8.01K, 3/4" NPT TY4811 .....Upright 8.0K, 1/2" NPT TY4911 .. . . Pendent 8.01K, 1/2" NPT TY3111 is a re-designation for S1800 and G3111. TY3211 is a re-designation for S1801 and G3112. TY4111 is a re-designation for S1810 and G3101. TY4211 is a re-designation for S1811 and G3102. TY4811 is a re-designation for S1805. TY4911 is a re-designation for S1806. NOVEMBER 2015 ASI 60297 2510 EL CAMINO REAL TFPI 10 TFPI 10 Pae 2 of 6 1 - Frame 3 - Ejection 5 - Strut 2 - Sealing Spring 6 - Hook Button 4 - Fusible 7 - Deflector* Element * Temperature rating ** Pipe thread connections per is indicated on ISO 7-1 can be provided on ESCUTCHEON Deflector, special request. PLATE SEATING SURFACE I (66,7 mm) 2-5/8 I5/8 7/16 I (11 1 mm) (66,7 mm) I NOMINAL 2" MAKE-IN 1mm) WR L EA ENCH 34 STYLE 20 \IU__-5 RECESSED \E' t ESCUTCHEON 7* 1/2 NPT** ) WRENCH - 2-7/8' (73,0 mm) DIA FLANGES UPRIGHT PENDENT RECESSED PENDENT CROSS SECTION FIGURE 1 STANDARD RESPONSE SERIES TY-L UPRIGHT (TY31II) AND PENDENT (TY3211) SPRINKLERS 5.6 K-FACTOR, 1/2 INCH NPT * Temperature rating ** Pipe thread connections per 1 - Frame 3 - Ejection 5 - Strut is indicated on ISO 7-1 can be provided on ESCUTCHEON 2 - Sealing Spring 6 - Hook Deflector. special request. PLATE SEATING Button 4 - Fusible 7 - Deflector* SURFACE Element W2-11/16" 11 (68,3 mm) 1/2" 2-11/16" (12,7 mm) (68,3 mm) NOMINAL 2 STYLE MAKE-IN (50,8 mm) ES RECESS CUTCIH 3/4" NPT** WRENCH 2-7/8" (73,0 mm) DIA. FLANGES WRENCI AREA UPRIGHT PENDENT RECESSED PENDENT CROSS SECTION FIGURE 2 STANDARD RESPONSE SERIES TY-L UPRIGHT (TY41I1) AND PENDENT (TY4211) SPRINKLERS 8.0 K-FACTOR, 3/4 INCH NPT TFPI 10 Page 3 of 6 * Temperature rating ** Pipe thread connections per 1 - Frame is indicated on ISO 7-1 can be provided on ESCUTCHEON 2 - Sealing Deflector. special request. PLATE SEATING Button 3 - Ejection 5 - Strut Spring 6 - Hook 4 - Fusible 7 - Deflector* Element WRENCH AREA 2 N 34 STYLE 20 RECESSED \i 't. ESCUTCHEON IEiJ-. 6 7* SURFACE 1 2-5/8 (66,7 mm) (50,8 mm) 2-7/8' (73,0 mm) DIA RECESSED PENDENT CROSS SECTION FIGURE 3 STANDARD RESPONSE SERIES TY-L UPRIGHT (TY4811) AND PENDENT (TV4911) SPRINKLERS 8.0 K-FACTOR, 1/2 INCH NPT Technical Data Approvals UL and c-UL Listed. FM, and LPCB Approved. (Refer to Table A for complete approval information including corrosion resistant status.) Maximum Working Pressure 175 psi (12,1 bar) Discharge Coefficient K=5.6 GPM/psi/2 (80,6 LPM/bar½) K=8.0 GPM/psi/2 (115,2 LPM/bar½) Temperature Ratings Refer to Table A Finishes Sprinkler: Refer to Table A Recessed Escutcheon: White Coated, Chrome Plated, or Brass Plated Physical Characteristics Frame .............................Brass Sealing Button ...........Bronze w/TEFLON Ejection Spring ..............Stainless Stool Strut ...... ...................... MONEL Hook ....... .............. Bronze/MONEL Deflector ..........................Bronze Fusible Element ............ ..Solder, Copper, Stainless Steel Operation A copper tube sealed by two stainless steel balls holds a fusible alloy. When the rated temperature is reached, the alloy melts, the balls are forced toward each other releasing the tension mech- anism, allowing the sprinkler to operate. Design Criteria The TYCO Series TY-L, 5.6 and 8.0 K-factor, Upright, Pendent, and Recessed Pendent Sprinklers are intended for fire protection systems designed in accordance with the stan- dard installation rules recognized by the applicable Listing or Approval agency (e.g., UL Listing is based on the require- ments of NFPA 13, and FM Approval is based on the requirements of FM's Loss Prevention Data Sheets). Only the Style 20 or 30 Recessed Escutch- eon, as applicable, are to be used for recessed pendent installations. Installation The TYCO Series TY-L, 5.6 and 8.0 K-factor, Upright, Pendent, and Recessed Pendent Sprinklers must be installed in accordance with this section: A leak tight 1/2 inch NPT sprinkler joint should be obtained with a torque of 7 to 14 ft-lbs. (9,5 to 19,0 Nm). A leak tight 3/4 inch NPT sprinkler joint should be obtained with a torque of 10 to 20 ft.-lbs. (13,4 to 26,8 Nm). Higher levels of torque may distort the sprinkler inlet and cause leakage or impairment of the sprinkler. Do not attempt to make-up for insuf- ficient adjustment in the escutcheon plate by under- or over-tightening the sprinkler. Readjust the position of the sprinkler fitting to suit. Series TY-L Pendent and Upright Sprinkler Installation The Series TY-L Pendent and Upright Sprinklers must be installed in accor- dance with this section. Pendent sprinklers are to be installed in the pendent position, and upright sprinklers are to be installed in the upright position. Step 1. With pipe thread sealant applied to the pipe threads, hand tighten the sprinkler into the sprinkler fitting. Step 2. Tighten the sprinkler into the sprinkler fitting using only the W-Type 9 Sprinkler Wrench (Ref. Figure 7), except that an 8 or 10 inch adjust- able Crescent wrench is to be used for wax coated sprinklers. With refer- ence to Figures 1, 2, and 3, the W-Type 9 Sprinkler Wrench is to be applied to the wrench area, or as applicable, the adjustable Crescent wrench is to be applied to the wrenching flanges. When installing wax coated sprinklers with the adjustable Crescent wrench, additional care needs to be exercised to prevent damage to the wax coating on the sprinkler wrench flats or frame arms and, consequently, exposure of bare metal to the corrosive environ- ment. The jaws of the wrench should be opened sufficiently wide to pass over the wrench flats without damaging the wax coating. Before wrench tightening the sprinkler, the jaws of the wrench are to be adjusted to just contact the sprin- kler wrench flats. After wrench tight- ening the sprinkler, loosen the wrench jaws before removing the wrench. TFPIIO Pae 4 of 6 Frame Sprinkler Finish K Type Temp. Rating Color Natural I Chrome Lead I Wax Wax Over Code Brass Plated Coated Coated Lead Coated Pendent (TY3211) 165°F (74°C) Unpainted 1, 2, 3 212°F (10000) White and 1, 2,3, 5 5.6 1/2' Upright (TY3111) 280°F (138°C) Blue 1,2 4 N/A NPT Recessed Pendent 165°F (74°C) Unpainted 1, 2, 3, 5 (TY3211 w/Style 20) N/A 1,2,3,5 212°F (100°C) White 165°F (74°C) Unpainted 1, 2, 3 212°F (100°C) White Pendent (TY4211) 1, 2, 3 280°F (138°C) Blue 1, 2 4 N/A 8.0 165°F (74°C) Unpainted 3/4" 1,2,3 212°F (100°C) White NPT Upright (TY4111) 1, 2, 3, 5 280°F (138°C) Blue 1,2 j 4 N/A Recessed Pendent 165°F (74°C) Unpainted 1, 2,5 N/A 212°F (100°C) White (TY4211 w/Style 30) Pendent (TY4911) 165°F (74°C) Unpainted 1, 2,3 2 12°F (100°C) White and 1, 2, 3, 5 8.0 1/2" Upright (TY4811) 280°F (138°C) Blue 1,2 N/A NPT Recessed Pendent 165°F (74°C) Unpainted 1,2 N/A 212°F (100°C) White (TY4911 w/Style 20) OTES: UL Listed C.uL Listed 3. FM Approved FM Approved for maximum 150°F (68°C) ambient temperatures LPCB Approved (LPCB Ref. No. 094a/03) N/A: Not Available TABLE A LABORATORY LISTINGS AND APPROVALS After installation, the sprinkler wrench flats and frame arms must be inspected and the wax coating retouched (repaired) whenever the coating has been damaged and bare metal is exposed. The wax coating on the wrench flats can be retouched by gently applying a heated 1/8 in. diam- eter steel rod to the areas of wax that have been damaged, to smooth it back over areas where bare metal is exposed. LTL.kE1i1 Only retouching of the wax coaling applied to the wrench flats and frame arms is permitted, and the retouching is to be performed only at the time of the initial sprinkler installation. The steel rod should be heated only to the point at which it can begin to melt the wax, and appropriate precau- tions need to be taken, when handling the heated rod, in order to prevent the installer from being burned. If attempts to retouch the wax coating with complete coverage are unsuc- cessful, additional wax can be ordered in the form of a wax stick (the end of which is color coded). Only the correct color coded wax is to be used, and retouching of wrench flats and frame arms is only permitted at the time of initial sprinkler installation. With the steel rod heated as previously described, touch the rod to the area requiring additional wax with the rod angled downward, and then touch the wax stick to the rod approximately one- half inch away from the area requiring retouching. The wax will melt and run down onto the sprinkler. Series TY-L Recessed Pendent Sprinklers Installation The Series TY-L Recessed Pendent Sprinklers must be installed in accor- dance with this section. Step A. After installing the Style 20 or 30 Mounting Plate, as applicable, over the sprinkler threads and with pipe thread sealant applied to the pipe threads, hand tighten the sprinkler into the sprinkler fitting. Step B. Tighten the sprinkler into the sprinkler fitting using only the W-Type 10 Recessed Sprinkler Wrench (Ref. Figure 8). With reference to Figure 1, 2, or 3, the W-Type 10 Recessed Sprinkler Wrench is to be applied to the sprinkler wrenching flanges. Step C. After the ceiling has been installed or the finish coat has been applied, slide on the Style 20 or 30 Closure over the Series TY-L Sprin- kler and push the Closure over the Mounting Plate until its flange comes in contact with the ceiling. CLOSURE TY-L FIGURE 6 SERIES TY-L (TY4911) RECESSED PENDENT SPRINKLER ASSEMBLY WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 20 RECESSED ESCUTCHEON 8.0 K-FACTOR, 1/2 INCH NPT CLOSURE TY-L FIGURE 4 SERIES TY-L (TY3211) RECESSED PENDENT SPRINKLER ASSEMBLY WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 20 RECESSED ESCUTCHEON 5.6 K-FACTOR, 1/2 INCH NPT 7/16±1/8" (11,1±3,2 mm) FACE OF SPRINKLER FITTING I \ - MOUNTING SURFACE 2-7/8" DIA. (73,0 mm) 2-1/4" DIA. (57,2 mm) 1/2" (12,7 mm) 1/4" (6,4 mm) MOUNTING PLATE mm) 1-3/4" (44,5 mm) 1-1/2' (38,1 mm) CLOSURE TY-L FIGURE 5 SERIES TY-L (TY4211) RECESSED PENDENT SPRINKLER ASSEMBLY WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 30 RECESSED ESCUTCHEON 8.0 K-FACTOR, 3/4 INCH NPT 7/16±1/8" 2-7/8" DIA. -j /2' (12,7 mm) (11,1±3,2 mm) (73,0 mm) 1/4" (6,4 mm) FACE OF 2-1/4' DIA. MOUNTING SPRINKLER (57,2 mm) 1 PLATE FITTING MOUNTING SURFACE J-koX III I) 1-3/4" (14,5 mm) 1-1/2" (38,1 mm) TFPI 10 Page 5 of 6 MOUNTING SURFACE - 2-7/8 DIA. 1/2 (12,7 mm) (73,0 mm) 1/4 (6,4 mr)1 2-1/4" DIA. MOUNTING DIATI FL.flIL ~~ r1JL / 1-3/4" (44,5 mm) 1-1/2" (38,1 mm) 7/16±1/8' (11,1±3,2 mm) FACE OF SPRINKLER FITTING I , C. 111111) WRENCH RECESS I FIGURE 8 W-TYPE 10 RECESSED SPRINKLER WRENCH Care and Maintenance The TYCO Series TY-L, 5.6 and 8.0 K-factor, Upright, Pendent, and Recessed Pendent Sprinklers must be maintained and serviced in accordance with this section. Before closing a fire protection system main control valve for maintenance work on the fire protection system that it controls, permission to shut down the affected fire protection system must be obtained from the proper authorities and all personnel who may be affected by this action must be notified. Absence of an escutcheon, which is used to cover a clearance hole, may delay the time to sprinkler operation in a fire situation. Sprinklers that are found to be leaking or exhibiting visible signs of corrosion must be replaced. Automatic sprinklers must never be painted, plated, coated or otherwise altered after leaving the factory. Modi- fied or over-heated sprinklers must be replaced. Care must be exercised to avoid damage to the sprinklers -before, during, and after installation. Sprinklers damaged by dropping, striking, wrench twist/slippage, or the like, must be replaced. Frequent visual inspections are rec- ommended to be initially performed for corrosion resistant coated sprin- klers, after the installation has been P/N 53 - XXX FSIN 111 5.6K UPRIGHT (1/2"NPT) TY3111 112 5.6K PENDENT (1/2"NPT) TY3211 101 8.OK UPRIGHT (3/4"NPT) TY4111 102 8.0K PENDENT(3/4"NPT) 1Y4211 106 8.OK UPRIGHT (1/2"NPT) 1Y4811 107 8.0K PENDENT (1/2"NPT) 1Y4911 I SPRINKLER TEMPERATURE FINISH 165 RATING 1 NATURAL BRASS 165°F (74°C) 6 WAX COATED 212 212°F(100°C) 165°FTO28O°FONLY 7 LEAD COATED 280 280°F (138°C) 8 WAX OVER LEAD 165°F TO 212°F ONLY 9 CHROME PLATED TFP 110 Pae 6 of 6 TABLE B SERIES TY-L PENDENT AND UPRIGHT SPRINKLERS PART NUMBER SELECTION completed, to verify the integrity of the corrosion resistant coating. Thereafter, annual inspections per NFPA 25 should suffice; however, instead of inspecting from the floor level, a random sampling of close-up visual inspections should be made, so as to better determine the exact sprinkler condition and the long term integrity of the corrosion resistant coating, as it may be affected by the corrosive conditions present. The owner is responsible for the inspection, testing, and maintenance of their fire protection system and devices in compliance with this document, as well as with the applicable standards of the National Fire Protection Asso- ciation (e.g., NFPA 25), in addition to the standards of any other authorities having jurisdiction. Contact the install- ing contractor or product manufacturer with any questions. It is recommended that automatic sprinkler systems be inspected, tested, and maintained by a qualified Inspec- tion Service in accordance with local requirements and/or national codes. Limited Warranty For warranty terms and conditions, visit www.tyco-fire.com. Ordering Procedure Contact your local distributor for avail- ability. When placing an order, indicate the full product name and Part Number (P/N). Sprinkler Assemblies with NPT Thread Connections Specify: Series TY-L (specify SIN), (specify K-factor), (specify Upright, Pendent, or Recessed Pendent) Sprin- kler, Standard Response, Standard Coverage, (specify) temperature rating, (specify) finish or coating, P/N (specify from Table B) Recessed Escutcheon Specify: Style (specify) Recessed Escutcheon with (specify finish), P/N (specify): 1/2" (15 mm) Style 20 Brass Plated ............ ..P/N 56-705-2-010 1/2" (15 mm) Style 20 Signal White (RAL9003).....P/N 56-705-4-010 1/2" (15 mm) Style 20 Chrome Plated ............P/N 56-705-9-010 3/4 (20 mm) Style 30 Brass Plated..............P/N 56-705-2-011 3/4" (20 mm) Style 30 Signal White )RAL9003) ..... P/N 56-705-4-011 3/4" (20 mm) Style 30 Chrome Plated ............P/N 56-705-9-011 Sprinkler Wrench Specify: W-Type 9 Sprinkler Wrench, P/N 56-000-1-849 Specify: W-Type 10 Sprinkler Wrench, P/N 56-000-1-948 Wax Sticks (for retouching wrench damaged wax coating) Specify: Series TY-L Sprinklers, (specify color), color coded Wax Stick for retouching, (specify) temperature rated, P/N (specify): Red for 165°F (74°c) .......P/N 56-065-1-155 Blue for 212°F (100°c) and 280°F (138°C) .........P/N 56-065-1-286 NOTES: Each wax stick is suitable for retouch- ing up to twenty-five sprinklers. The wax used for 280°F (138°C) sprin- klers is the same as for 212'F (100°C) sprinklers, and, therefore, the 280°F (138°C) sprinkler is limited to the same maximum ceiling temperature as the 212°F (100°C) sprinkler (i.e., 150°F (65°C)). GLOBAL HEADQUARTERS 11400 Pennbrook Parkway, Lansdale, PA 19446 I Telephone +1-215-362-0700 Copyright © 2015 Tyco Fire Products, LP. All rights reserved. tqcii MONEL is trademark of Special Metals Corporation. Fire Protrrctio,r Prorlr,cts TEFLON is trademark 01 The DuPont Corporation A a:MA : ~ ,ITT Full Line Sch-40 Replacement Dyna-Thread offers the life expectancy of Sch-40 with superior hydraulics and greater value. Dyna-Thread sprinkler pipe represents an engineering advancement for the sprinkler pipe industry. It combines the safety and longevity of traditional Sch-40 pipe with quality and superior hydraulic advantages. Dyna-Thread's inside diameter is up to 3.6% larger than Sch-40 giving it Superior hydraulics. And, when used in combination with Dyna-Flow pipe, down sizing often occurs. Dyna-Thread is fully listed and approved by UL, ULC, and FM for lire sprinkler applications. the life expectancy of Dyna-Thread and Sch-40 are equal based on the calculated wall thicknesses per UL. The consistent quality of steel used to make Dyna-Thread facilitates smooth threading and lower maintenance costs. The exterior of Dyna-Thread is protected by a clean, durable mill coating for extended shelf life and easy pai nt application. ~ U L 0 L) ULC Listed Approved Listed With its increased strength and lighter weight, Dyna-Thread reduces installation fatigue and is ideal for retro-fit applications. Corrosion Resistance Ratio (CRR) is a UL (Underwriters Laboratory) term for the estimated life expectancy of a pipe joint. This is based on the calculated wall thickness at the base of the first exposed thread, assumed to be the weakest point of the PC length. Dyna- Thread and Sch-40 have the same calculated wall thicknesses at this point and are both assigned the same CRR of 1.00. The internal surface of all black Allied Tube & Conduit Fire Sprinkler pipe products tip to 4.5000" in diameter is coated with our new Antibacterial Formula, "ABF". In scientific laboratory test, ABS proved to have superior resistance to microbial colonization of pipe walls, thereby delaying or possibly preventing the onset of Microbiologically influenced corrosion (MIC) when the First Sprinkler System is first installed. More wall thickness at the thread (CRR 1.00) gives Dyna-Thread better life expectancy than lightwall threadable pipe joints. Unlike liglltwall threadable pipe, Dyna-Thread has 110 thread gauge warning. Dyna-Thread is approved for standard hanger spacing (15 ft. can be used as earthquake sway bracing, and is safe to use as drops. Dyna-Thread is safer to weld on. Dyna-Thread is more widely accepted than liglltwall threadable where Sch-40 is specified. Super 40/Dyila-Thread pipe is manufactured to meet: ASTM A-135, Grade A and is in compliance with NFPA- 13. Alt sizes of Super 40/Dyna- Thread are rated at 300 psi working pressure. Super 40/Dyna-Thread is UL and ULC Listed for wet, dry deluge and pre-action sprinkler systems and FM Approved for use in wet systems. Super 40/Dyna-Tllread can be "hot-dip" galvanized to meet FM requirement for dry systems. Super 40/Dyna-Thread is approved for all threaded couplings and welded Outlets and is suitable for all roll-grooved, and plain-end fittings. (See listing information). i -itm NPS Nominal I.D. WI. Wt. (H20 Filled) Pcs/ WI/Lilt (21) WI/Lill (24) WI/Lilt (25) In; rnrn In; rnrn Lbs/Fl; Kg/rn Lbs/Fl: Kg/rn Lill Lbs; Kg Lbs: Kg Lbs; Kg 1.080 1.330 1.75 70 1955 2234 2327 25 27.4 2.0 2.60 70 887 1013 105 11/4' 1.408 1.870 2.54 51 2002 2288 2384 32 35.8 2.8 3.78 51 908 1038 1081 11/2" 1.639 2,290 3.22 44 2115 2418 2519 40 41.6 3.4 4.79 44 959 1097 114 2.104 3.050 4.57 30 1921 2196 2287 50 53.4 4.5 6.80 30 871 996 103 16100 S. Lathrop • Harvey, IL 60426 Customer Service: tLICO/Flow Control cIIiecJ 11350 Norcom Rd. . Philadelphia, PA 19154 (800) 882-5543 TUBE & CONDUIT 2525 N. 27 th Ave. Phoenix, AZ 85009 Fax 708-339-1806 S3 -3 DIMENSIONS SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS STYLE 922 The Style 922 Outlet-i provides a convenient method of incorporating ½, 3/4, and 1/15 20 and 25mm outlets for directly connecting sprinklers, drop nipples. sprigs, gauges, drains and other outlet products. Available for 11// through 76.1 mni/32 to /6.1 mm piping systems, Style 922 outlets are UL/1-11.0 Listed, LPC. Vds/FM approved for branch conneclions on we[ and dry systems I he locating collar engages into the hole prepared in the pipe. When tightened, the assembly compresses the gasket oi ito the 01"', of the pipe. I he Style 922 Outlet-1 is UI_/FM rated U() to 300 psi/2068kPa and VdS rated up to 16 bar at the ambient temperatures typical for fire proteclion systems. Style 922 is suitable for use on standard, lightwall, Schedule 5 and other specialty pipes: It is sLippliedt with a clear, rust inhibitive coating. Contact Victaulic for other optional coatings. *Consult Section 10.01 for specific listings/approvals i9 1 14 / 1,10 3.87 Z56 W 22 ' 15 30.2 33.0 463 229 98.3 65.0 OAS 21.193 110 3 ,97 756 I.) 20 30.2 :i s 'ie.s , 29 983 65.0 OM 52 05 .1)) '157 7.56 I'7 25 (().,? 056 553 777 (14 3 65.0 11.5-1 1 1/2 0 13 1')', 12! 108 ;. 1, 47 " 0 30." 05.1 49.5 51.0 101.6 65.0 004 110 1.9t, 1.// lOP 2.50 2 1(1.2 758 7) :o o 03.2 98.0 .01 2.00 72 i.us iSo .3 25 3(1.2 '11.7 5)64 31.0 03.6 65.0 0.59 7 1,0 2.19 t 7) 4.98 2Si .3 50 >, ' iS 502 4,17 55.6 372 116.8 65.0 0.50 N k., 1 Ii. 4.oO 205 1.4 20 302 'II / 55.6 3,11 116.8 698 0.64 25 .30' .1711 61.5 (7, 116.8 650 0.68 11, 1,91 '.44 1.71 5.40 2.lo 1.6 65 " IS 102 16.' 32" '13.3 13/.? 65.0 051 62.0 1, 'l .0 3-os t./9 /1 '/10 ,S5o I.)) 25 30.2 'iii 71.9 .13.1 137.2 63.1) 0.73 mm .6.1 6 'II 244 171 0.51) 256 1.11 002 485 62.0 434 139.7 000 0.73 1.21 553 2.58 1.6 20 302 44.0 62.0 '134 139.7 65.0 013 1 05 2.11 2.7'? 05/I 5.50 7.00 1.7 21 31'1:' "Li 70.7 054 139.7 03.13 0.120 I VS. 051iIIL f/thY'! tl' read eu produ :05 arc' desici cO to ac:Lorninlodace standard NP I or BSP I (optional) nrale pipe Lliri'ad', cot!. Usc of make t1ift.'1d'1d prodoc ts mod special features, such as probes, dry pen- dent sprinklers, etc., should be verified as suitable for use with this Victaiilic product Failure to verify suitability in advance may result in assembly problems or 1eak'1e. Centcr of run to engaged pipe end for NPT 1head3 (dimensions are approximate). JOB OWNER CONTRACTOR ENGINEER System No. Submitted By Spec Sect___ Para Location Date Approved Date www.victaulic.com VICTAULIC IS SECISTdRLD TRADEMARK or VIOTAIJLO'. COYr'ANY 21/3d VICTAUuC COMPANY ALL SIC) ITS RESERVED. PRINTED IN THE USA. X0 A-Ctc ItE'! C , 10.52 1 L 10.52 ) © - SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS STYLE 922 01 MATERIAL SPECIFICATIONS Housing: DUO ile iron conforming to ASTM A-536, grade 65-45-12. Ductile iron conforming to ASTM A-395, grade 65-45-15, is available upon special request Gasket: Grade "E" EPDM - Type A (Violet color code). Firel.ock products have been listed by Underwriters I.aboraLones Inc. and Approver) by Factory Mutual Research for wet and dry (oil free air) sprinkler services up to the rated working pressure using the Grade 'F Type A Gasket System. Bolts/Nuts: Heat-treated plated carbon steel, trackhead meeting the physical and chemical require- ments of ASTM A-449 and physical requirements of ASTM A-183. www.victauliC.Com - - vrcTAuLlc Is OEC;isTd1EO TRADEMARK Or VICTAL)LIT COMPANY 02100 ViCTAIJLIC COMPANY ALL rilcHrs RdsdrvcD. PRINTED IN THE USA , X, Anc—ta _U1 REV t t STYLE 922 PERFORMANCE 10.52 SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS 'K 40 y 25 2 I 8.5 50 25 2.6 7½ • 1 8.5 65 25 . 26 I 8.5 76.1 NY)) ,S www.viCtauliC.com ictauPc VICTAULIC IS rIECATErIED TRADEMARK or VCTAUL)C COMPANY C' 2006 VICTA)LIC COMPANY ALL VIOl ITS RESERVED. PIONTED iN THE USA. N' P . 10.52 3 iii~ mw 1-11 STYLE 922 SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS WARRANTY Refer to the Warranty section of the currnnr, Price List or contact Victaulic for details. NOTE 1 His product shall be rnanLifacturvd by Victaulic or to Victaulic specifications. All products to he rivt3lted In accordance with current Victaulic instaltation/assernbly instructions. Victaulic reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations. US & WORLD HLAOUUARTLRS CANAOA P.O. Box 31 9015-884 -7444 Lesion, PA J804/1 0031. USA 905 8849774 (tax) 4901 Kesslersville Road viccanada@victaulic.com Easton, PA 1.80,10 USA 1-800-PICK-VIC (1-800-742-5842) 32-9-381-15-00 1-610-559-3300 32-9-380-44-38 (lax) 1-610-250-881/ (fax) viceuro@victaulic.be pickvic@vic ta ulic. 000 www.victauhc.Com 44 (0) 1438741100 44 (0) 1/13831.3883 ((ax) viceu mo@)victa iclic, be CENTRAL AND SOs)'h ALRICA 1-610 -559 3300 (6(0 5593608 (lax) vice I(cHvictaij tic corn x, A Pe0iE. 86-21-54253300 86-21-54253671 (fax) vicap@victaulic,corn 9/1-4-88388-70 97 1-4 883 88-60 (lax) \AIrA0Pfl lET UPDATED 5/2006 10.52 335S REV C v UTAULIC: iA A iTLOiSTLaLL; cirLLMAI//, (Ti sit; A.IU COMPANO. A 20Cc6 VlcIAULIC OM'ANY ALL NiOli IS 'TLLLRvLL) Al' Ni LU IN Ii If- i ills. IOn) jctauhc r / \\ if I' if I3 0 Ii A 2 1/2 THRU 8 INCH PIPE 1/2 THRU 2 INCH PIPE Fig. 200 - "Trim line" Adjustable Band Hanger Size Range - 1/2 thru 8" pipe Material - Carbon Steel, Mu. Galvanized to G90 specifications Function - For fire sprinkler and other general piping purposes. Knurled swivel nut design permits hanger adjustment after installation. Features - (1/2 thru 2') Flared edges ease installation for all pipe types and protect CPVC plastic pipe from abrasion. Captured design keeps adjusting nut from separating with hanger. Hanger is easily installed around pipe. (21/2' thru 8') Spring tension on nut holds it securely in hanger before installation. Adjusting nut is easily removed. Approvals - Underwriters' Laboratories listed (1/2" thru 8') in the USA (UL) and Canada (cUL) for steel and CPVC plastic pipe and Factory Mutual Engineering Approved (3/4' thru 8'). Conforms to Federal Specifications WW-H-171E, Type 10 and Manufacturers Standardization Society SP-69, Type 10. Maximum Temperature - 650°F Finish - Mil. Galvanized. For Stainless Steel materi- als, order TOLCOTM Fig. 200WON. Order By - Figure number and pipe size Dimensions • Weights Pipe Rod Size Max. Rec. Approx. Size Inch Metric A B Load Lbs. Wt./100 1/2 3/8 8mm or 10mm 31/8 2/8 400 11 3/4 3/8 8mm or 10mm 31/8 21/2 400 11 1 3/8 8mm or 10mm 33/4 2/8 400 12 11/4 3/8 8mm or 10mm 33/4 2/8 400 13 11/2 3/8 8mm or 10mm 37/4 27/8 400 14 2 3/8 8mm or 10mm 41/2 3 400 15 21/2 3/8 10mm 55/4 41/8 600 27 3 3/8 10mm 57/8 4 600 29 31/2 3/8 10mm 73/8 51/4 600 34 4 3/8 10mm 73/8 5 1000 35 5 1/2 12mm 91/8 61/4 1250 66 6 1/2 12mm 101/8 63/4 1250 73 8 1/2 12mm 131/8 83/4 1250 136 OFFICE/MANUFACTURING FACILITY • 1375 SAMPSON AVE. • CORONA, CA 112879 • PH 951.737.5599 • FAX: 951 737,0330 CUSTOMER SERVICE • 800.786.5266 www.tolco.com C®US LISTED Fig. 25 - Surge Restrainer Size Range - One size fits 3/4' thru 2" pipe. Material - Pre-Galvanized Steel Function - Designed to be used in conjunction with TOLCO® Band Hangers to restrict the upward movement of piping as it occurs during sprinkler head activation or earthquake type activity. The surge restrainer is easily and efficient- ly installed by snapping into a locking position on the band hanger. This product is intended to satisfy the requirements as indicated in the National Fire Protection Association (NFPA 13, 1999 Edition), 6-2.3.3, 6-2.3.4 and A-6i-2.3.3 Can be used to restrain either steel pipe or CPVC plastic Pipe. Approvals - Underwriters' Laboratories Listed p.niy when used with TOLCO band hangers Fig. 2, 2NFPA and 200, in the USA (UL) and Canada (cUL). Finish - Pre-Galvanized Order By - Figure number and TOLCO band hanger, size from 3/4" thru 2". Patent #5,344,108 OFFICE/MANUFACTURING FACILITY • 1375 SAMPSON AVE • CORONA, CA 82879 • PH 951.737.5599 • FAX. 951.737 0330 CUSTOMER SERVICE • 800.786.5266 www.toico.co,,, Size Range - Secures 3/8 thru 7/8 rod in 1 ° increments Material - Carbon Steel Maximum Temperature - 750°F Finish - Plain Note - Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By - Figure number, rod diameter, rod length and finish Dimensions Rod Rod Max. Rec. Load Lbs. Size For Service Temp 650°F 3/8 730 1/2 1350 5/8 2160 3/4 3230 7/8 4480 Component at State of California OSHPD Approved Seismic Restraints System H FIG. 98 - Fig. 98 - Rod Stiffener Fig. 98B - Rod Stiffener wlBreak-off Bolt Head Size Range - Secures 3/8 thru 7/8 hanger rod Material - Carbon Steel Function - Secures channel to hanger rod for vertical seismic bracing. Approvals - Included in our Seismic Restraints Catalog approved by the State of California Office of Statewide Health Planning and Development (OSHPD). For additional load, spacing and placement information relatina to OSHPD oroiects, olease refer to the TOLCO Seismic Restraint Systems Guidelines Finish - Electro Galvanized Note - Available in HDG finish or Stainless Steel materials Order By - Figure number i FIG. 98B Fig. 99 - All Thread Rod Cut to Length Size Range -- Secures 3/8" thru 1112" rod in 10' lengths Material - Carbon Steel Maximum Temperature - 750°F Finish - Plain Note - Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By - Figure number, rod diameter and finish Fig. 100- All Thread Rod Full l..tnnth Dimensions Weights Max Rec. Load Lbs. Rod For Service Temps Approx. Size 650°F Wt./100 1/4 240 12 3/8 730 29 1/2 1350 53 5/8 2160 84 3/4 3230 123 7/8 4480 169 1 5900 222 1¼ 9500 360 1½ 13800 510 . OFFICE/MANUFACTURING FACILITY • 1375 SAMPSON AVE. • CORONA, CA 92879 • PH. 951 737.5599 • FAX: 1151 737,0330 CUSTOMER SERVICE • 800.186 5768 www.toico.com Not toss than 2" nominal width Wood Flooring Product Features No pre-drilling required. Not loss than a Quick to install using the Sammy 3 nominal /J Nut Driver with an iSV cordless J / thickness Wand Jn drill/driver. vi vertical monition)------------- ,//, ---- -- - ------ Saves time from traditional Double Sheobock methods. / Coiling GO- _____________________ • Reduces installation cost. Made in the U.S.A. iS [is an Qrj JTh i " 1/4 8002957 GST 100 1/40 1" 1/4 8003957 GST 200 1/40 2" 1760 (Fir) 1/4 8004957 GST 300 1/4o 3" 2060 (Fir) 3/8" 8006957 GST 75 1/4s3/4" 564 (314" Ply) 3/8" 8007957 GST 10 1/40 1" 3/8" 8008957 GST 20 114 2' 1760 (Fir) 3/8" 8068925 GST 20-SS 1/40 2" 1760 (Fir) 3/8" 8009925 GST 25-380 3/80 2-1/2" 2113 (Fir) 3/8" 8010957 GST 30 1/40 3" 2060 (Fir) 3/8" 8069925 GST 30-SS 1/403" 2060 )Fir) 3/8" 8011925 GST 40 1/4v4" 2180 (Fir) 3/8" 80) 2925 GST 60 1/406" 2230 (Fir) 1/2" 8013925 GST 2 1/402" 1760 (Fir) 1/2" 8014925 GST 2.5-380 3/80 2-1/2" 2113 (Fir) 1)2" 8015925 GST 3 114 x 3" 2275 (Fir) 1/2" 8016925 GST 4 1/404" 2180 (Fir) 1/2" 8017925 GST6 1/406" 2230 (Fir) ), - 25 125 25 125 25, 125 25 125 300 25 125 850 1475 25 125 850 25 125 1500 25 125 1500 1475 25 125 #14 Black 25 125 Nut Driver Part #8113910 25 125 25 125 — 25 125 25 125 914 SW Ined Nut Driver Part #8114910 Product Features Eliminates distortion of threaded rod. • Saves time from traditional methods. Lcommodates up to 3 l/nS x 12 pitch roof. Reduces installation cost, ws17deftection from vertical. • Made in the U.S.A. 3/8" 8139957 SH-GST2O 114x 2' 1257 (Fir) 1050 1475 25 125 125 3/8" 8141957 SH-GST30 1/4n3" 1720 (Fir) 1500 1475 25 125 #14 Black Nat Driver SPECIAL NUT DRIVER SYSTEM; The nut drivers were designed with a unique spin-off feature which provides a fact and gale installation each time. When the lace of the driver comes into Part #8113910 contact with the material you are installing into, covlinue drilling until nut driver spins tree. Installation is their complete. Warranty requires the use of the appropriate net driver for installations. MADE IN U.SA, 'r' 1iS) 0 a ~MWUNMXTWEUMax EWER Dn vortixat l.,VVL I-lid 200 1-1/2' 8020957 SWG 10 318 Horizontal CPVC 1-1/2" 300 1-1/2" 8008957 GST 20 3/8" Vertical 2-1/2" 850 1-1/2" 4" 1475 1-1/2' 8068925 GST20-SS 3/8" Vertical 2-1/2" 850 1-1/2" 8010957 GST3O 3/8" Vertical 4" 1500 1-1/2" 4" 1475 1-1/2" 8009925 GS125-380 3/8" Vertical 4" 1500 1-112" 8022925 SWG 25-380 318" Horizontal 3-1/2-4"" 1500 1-1/2" 8021957 SWG 20 3/8" Horizontal 2-1/2" - 3""" 1050 1-1/2" 8073925 SWG 20-SS 3/8" Itorizontal 2-1/2" 850 1-112" 8139957 Sl-l-GST 20 3/8" 17" Angle oil Vertical 1050 1-1/2" 4" 1475 1-1/2" 8141957 SH-GST 30 3/8" 17" Angle off Vertical 1500 1-1/2" 4" 1475 1-1/2" SAMMYS® FOR STEEL I : gLIL UiMTIS,t1 FM Max $ 1JIOROT$1000010ze i1Isi 8038957 DSTR 1 3/8" Vertical 41, 1500 .035" 4" 1475 .105" 8037957 DSTR 1-1/2 3/8" Vertical 4" 1500 .035" 4" 1475 .105" 8039957 DSTR 516 3/8" Vertical 4" 1500 .037" 4" 1475 .105' 8045957 DST 516 3/8" Vertical 4" 1500 .188" 4" 1475 .188" 8040957 /EI< 50 3/8" Vertical 4" 1500 .250" 4" 1475 .188" 8055957 SWDR 1 3/8" Horizontal 4" 1500 .037" 4" 1475 .060" 8056957 SWDR 516 3/8" Horizontal 4" 1500 .037" 4" 1475 .060" 8054957 SWDR 1-1/2 3/8" Horizontal 4" 1500 .037" 4" 1475 .060" 8137957 SH-DSTR 1 3/8" 17" Angle oil Vertical 4" 1500 .035" 4" 1475 .105" 8150922 XP 20 3/8" Vertical 2-1/2" 850 .027" i1° 7 8153922 XP 35 3/8" Vertical 4" 1500 .060" ,, 1475 .105, 8294922 SXP 20 3/8" Vertical or up 1045" 2" 750 .027" 2" 635 .029" 8295922 SXP 35 318" Vertical or up 1089" 3-1/2" 1250 .060" 2" 635 .029" 8293957 SWXP 35 318" Horizontal 3-1/2" 1250 .060" 8059957 CST 20 3/8" Vertical 4" 1475 3000 8061957 SWC 20 3/8" Horizontal 4" 1475 3000 8150922 XP 20 3/8" Vertical 2-1/2" 850 Pre-Pour Structural @ 3000p0i 8150922 XP 20 3/8" Vertical 2-1/2" 850 Pool-Pour Range II LWC a 35 PCF (lbo/113) TRUSS-T HANGER® Mi wag 8296900 HD38TC 3/8" lop Chord 1200 6075 Maximum 4" Schedule 40 pipe 8297900 1'103813C 3/8" 13ot1orn Chord 1200 6075 Maximum 4" Schedule 40 pipe 8198900 llD12CZP 1/2" Bottom Chord 1200 6075 Maximum 8" Schedule 40 Pipe 8298900 H1312TC 1/2" Top Chord 1200 6075 Maximum 8" Schedule 40 Pipe 8299900 H[)1213C 1/2" Bottom Chord 1200 6075 Maximum 8" Schedule 40 Pipe "SWG 25-3e0 Maximum pipe size in composite wood mist allowed by UL is 3-1/2" UL compliance wdh NEC Standards, "SWG 25-30 Maximum pipe size in wood limbo) or joist a/owed by UL is 4" Ut and FM tests were performed in compliance with NFPA 13 Standards. ""SWG 20 Maximum pipe size in r.onrponile wood isis) allowed by UL is 2-1/2 Fastening requirement: S limos weight of water-filled schedule 40 pipe plus zoo pounds ""SWG 2e Max/mom pipe size in wood Umber or joist allowed by UL is 3" CuS <S> LISTED PIPE tIANOER ALSO 000Eo an c0500n AND CABLE HARDWARE APPROVED ALSO usnue AS xectioe FOR LUMINatRE seal 1. ' For the most up' to date informaon, visit wW sammsuperscrew corn 14]