Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
560 CARLSBAD VILLAGE DR; 102; AS090049; Permit
City of Carlsbad Sprinkler Permit Permit No: AS090049 560 CARLSBAD Job Address: VILLAGE DR Permit Type: SPRINK Parcel No: 2032922200 Lot #: 0 Reference No.: Status: ISSUED Applied 6/3/2009 Approved: 6/3/2009 Issued: 6/3/2009 PC #: Inspector: Project Title: PER SE RESTAURANT T.I. FIRE SPRINKLER PLAN CHECK & INSPECTION Applicant: SENTRY FIRE PROTECTION 318 STATE PL ESCONDIDO, CA 760-747-7447 Owner: HURLEY THOMAS J 1015 CHESTNUT AVE #F2 CARLSBAD CA L Fees ($) Add'I Fees ($) Total ($) Balance ($) 130 0 130 0 Also I c) o +7 April 24, 2009 Sprinkler 101 STANDARD RESPONSE N4 KJ Fs1G l:II[.1u.rM DRY PENDENT SPRINKLERS The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-818-1680 Email: techsvcsvikingcorp.com DESCRIPTION Viking Standard Response Dry Pendent Sprinklers are thermosensitive spray sprin- klers suitable for use in areas subject to freezing. The sprinklers are designed for dry systems and preaction systems where it is necessary to prevent water or condensation from entering the drop nipple before sprinkler operation. They may also be installed in spaces subject to freezing and supplied from a wet system in an adjacent heated area. Viking Standard Response Dry Pendent Sprinklers are available in various finishes and temperature ratings, standard or large orifice, to meet design requirements. The large orifice dry pendent sprinkler allows greater flows at lower pressures than standard orifice sprinklers. LISTINGS AND APPROVALS cULus Listed: Category VNIV FM Approved: Classes 2013 and 2015 NYC Approved: MEA 89-92-E, Volume 37 LPCB Approved: Ref. No. 096e/06 CE Certified: Standard EN 12259-1, EC-certificate of conformity 0832-CPD-2001 MED Certified: Standard EN 12259-1, EC-certificate of conformity 0832-MED-1 003 NOTE: Other International approval certificates are available upon request. Refer to the Approval Chart on page 101d and Design Criteria on page 101e for cULus Listing and FM Approval requirements that must be followed. 3. TECHNICAL DATA Specifications: Available since 1991. Minimum Operating Pressure: 7 psi (0.5 bar)* Maximum Working Pressure: 175 psi (12 bar). Factory tested pneumatically to 100 psi (6.89 bar) Thread size: 1" NPT or 25 mm BSP Nominal K-Factor for Standard Orifice Sprinklers: 5.6 U.S. (80.6 metric**) for all listed and approved lengths. Viking Technical Data may be found on The Viking Corporation's Web site at http://www.vikinggroupinc.com. The Web site may include a more recent edition of this Technical Data Page. Nominal K-Factor for Large Orifice Sprinklers: 8.0 U.S. (115.2 metric) for lengths up to 20". For lengths exceeding 20", refer to Figure 6 on page 101g. Glass-bulb fluid temperature rated to -65 °F (-55 °C) *cuLus Listing, FM Approval, and NFPA 13 installs require a minimum of 7 psi (0.5 bar). The minimum operating pressure for LPCB and CE Approvals ONLY is 5 psi (0.35 bar). **Metric K-factor measurement shown is when pressure is measured in bar. When pressure is measured in kPa, divide the metric K-factor shown by 10.0. Material Standards: Frame Casting: Brass UNS-C84400 Deflector: Brass UNS-C26000 Bulb: Glass, nominal 5 mm diameter Belleville Spring Sealing Assembly: Nickel Alloy, coated on both sides with Teflon Tape Displacement Ring: Phosphor Bronze UNS-051000 Compression Screw: Brass U NS-C36000 Pip Cap: Brass UNS-C3 1400 or UNS-C31600 Pip Cap Adapter: Brass UNS-C36000 Seat (for Sprinklers VK151, VK155, and VK159 only): Copper UNS-C21000 Orifice: Copper UNS-C21000 Gasket: Buna-N Tube: ERW Hydraulic Steel Tube Inlet: Brass UNS-C31400 or UNS-C31600 Support (Internal): Stainless Steel UNS-S30400 for Sprinklers VK151, VK155, and VK159 Brass UNS-C36000 all other sprinklers. Form No. F_071591 Replaces page 101a-h, dated April 10, 2009. (Added note regarding CPVC tee fittings.) Sprinkler 101 April 24, 2009 STANDARD RESPONSE sJ! F(J F16 DRY PENDENT SPRINKLERS The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-818-1680 Email: techsvcsvikingcorp.com Barrel: Steel Pipe UNS-G10260, Electrodeposited Epoxy Base finish Barrel Threads: UNS-G 10260 Sleeve (for Adjustable Standard style only): Brass UNS-C26000 or UNS-C26800 Escutcheon Materials: Adjustable Standard Dry Escutcheons: Brass UNS-C26000 or UNS-C26800 Recessed Dry Escutcheons: Cold Rolled Steel UNS-010080 Ordering Information: (Also refer to the current Viking price list.) Order Standard Response Dry Pendent Sprinklers by first adding the appropriate suffix for the sprinkler finish, the appropriate suffix for the temperature rating, and then the suffix for the length ("A" dimension) to sprinkler base part number. Order in a specific length noted as the "A" dimension (see Figures 3 through 5). The "A" dimension is the distance from the face of the fitting (tee) to the desired finished surface of the ceiling. These sprinklers are listed and approved in lengths from 1-1/2" to 45-1/2" (38.1 mm to 1,156 mm) for the adjustable standard style, 3" to 47(76.2mm to 1,194 mm) for the plain barrel style, and 3-1/4" to 47-1/2" (82.5 mm to 1,207 mm) for the adjustable recessed style. Lengths exceeding the standard lengths are available, with no approvals, on a "made-to-order' basis: Recessed Dry Pendent up to 65-1/2" (1,664 mm) for standard orifice and 64-1/4 (1,632 mm) for large orifice. Adjustable Standard Dry Pendent up to 63- 1/2" (1,613 mm) for standard orifice and 62" (1,575 mm) for large orifice. Plain Barrel Dry Pendent up to 65" (1,651 mm) for standard orifice and 64" (1,626 mm) for large orifice. Contact the manufacturer for more information. Finish Suffix: Brass = A, Chrome-Enloy® = F, and White Polyester = M-AN Temperature Suffix (°F/°C): 155°/68° = B, 175/79° = D, 200°/93° = E, 286°/141° = 0 For example, sprinkler VK154 with 1" NPT Threads, a Chrome finish and a 155 °F/68 C temperature rating, and "A" length of 10" = Part No. 07740FB10. Available Finishes And Temperature Ratings: Refer to Table 1 Accessories: (Also refer to the "Sprinkler Accessories" section of the Viking data book.) Sprinkler Wrenches: Standard Wrench: Part No. 07297W/B (available since 1991) Wrench for recessed sprinklers: Part No. 07565W/Bt (available since 1991) tA 1/2 ratchet is required (not available from Viking). Sprinkler Guard: Chrome, with no listings or approvals, for installation on dry pendent sprinklers manufactured after May 1994 only (Part No. 08954). Replacement Escutcheons: Adjustable Standard Dry Escutcheon: Base Part No. 07741 Recessed Dry Escutcheon Cup: Base Part No. 05459A INSTALLATION Refer to appropriate NFPA Installation Standards. OPERATION During fire conditions, the heat-sensitive liquid in the glass bulb expands, causing the glass to shatter, releasing the internal parts to open the waterway. Water flowing through the sprinkler orifice strikes the sprinkler deflector, forming a uniform spray pattern to extinguish or control the fire. INSPECTIONS, TESTS AND MAINTENANCE Refer to NFPA 25 for Inspection, Testing and Maintenance requirements. AVAILABILITY The Viking Standard Response Dry Pendent Sprinkler is available through a network of domestic and international distributors. See The Viking Corporation web site for the closest distributor or contact The Viking Corporation. GUARANTEE For details of warranty, refer to Viking's current list price schedule or contact Viking directly. April 24, 2009 Sprinkler 101 STANDARD RESPONSE I FJ I'1r1E DRY PENDENT SPRINKLERS The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-818-1680 Email: techsvcsvikingcorpcom TABLE 1: AVAILABLE SPRINKLER TEMPERATURE RATINGS AND FINISHES Sprinkler Temperature Sprinkler Nominal Maximum Ambient Classification Temperature Rating' Ceiling Temperature' Bulb Color Ordinary 155°F(68°C) 100°F(38°C) Red Intermediate 175 °F (79 00) 150 °F (65 °C) Yellow Intermediate 200 °F (93 00) 150 °F (65 00) Green High 286 °F (141 °C) 225 °F (107 °C) Blue Sprinkler Finishes: Brass, Chrome-Enloy (patents pending), and White Polyester Footnotes 1 The sprinkler temperature rating is stamped on the deflector. 2 Based on NFPA-13. Other limits may apply, depending on fire loading, sprinkler location, and other requirements of the Authority Having Jurisdiction. Refer to specific installation standards. Wrench F1o.± Protective 01SNj Sprinkler 3AW3d Shield VIKING 07297 Figure 1: Standard SprinkI9r Wrench 07297W/B Sprinkler 101d April 24, 2009 STANDARD RESPONSE J I KJ t1Gu DRY PENDENT SPRINKLERS The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Approval Chart Temperature I-- KEY Fhsh Standard Response Dry Pendent Sprinklers rEscutcheonappJicabe) Maximum 175 PSI (12 bar) WWP Sprinkler Thread Size Nominal Order Length Listings and Approvals4 Base Part SIN Style K-Factor2 Increment (Refer also to Design Criteria on page 101e.) Number' NPT BSP U.S. metric3 Inches j mm cULus6 FM NYC6 VdS LP-- Standard Orifice 07740 VK154 Adjustable 1" -- 5.6 -- 1/2 12,7 Al A3 Al -- -- -- -- 07854 VK154 -- 25 mm -- 80.6 1/2" Standard 12.7 Al A3 Al -- -- -- -. 09341 VK155 -- 25 mm -- 80.6 1/2" 12.7 -- -- -- -- A3 A3 A3 06530 VK158 Adjustable Recessed 1" -- 5.6 -- 1/4" 6.35 84 B4 B4 -- -- -- -- 07853 VK158 -- 25 mm ____ ____ 80.6 1/4" 6.35 B4 B4 B4 09342 VK159 -- 25 mm --80.6 ____ 1/4" 6.35 -- -. -- VK150 Barrel 1" -- -- 07852 5.6 A5 Plain -.1/2" 12.7 A5 A5 -- WA5A5 07855 VKl50 25 mm --80.6 1/2" 12.7 A5 A5 VK151 -- 25mm A5 09343 -- 80.6 1/2" 12.7 -- -- -- -- Large Orifice Sprinkler Thread Size Nominal Order Length Listings and Approvals4 Base Part SIN Style Increment (Refer also to Design Criteria on page 101e.) Number' K-Factor2 NPT BSP Inches mm cULus5 FM NYC, VdS LPCB (( • 12810 VK163 Adjustable Standard 1 _ -- 8.0 U.S. (1152 metric') for lengths up to 20". For lengths over 20", refer to Figure 6 on page 101g. 1/2" .11.. Al 12813 VK163 -- 25 mm 1/2" 12.7 Al - A2 -- -- -- 12811 VK164 Adjustable Recessed 1" 1/4" 6.35 B4 -- 84 -- -- -- -- 12814 VK164 -- 25 mm 1/4" 6.35 B4 - - 64 - 12741 VK166 Plain Barrel 1" -- 1/2" 12.7 A5 -- A5 - -- -- -- 12812 VK166 -- 25 mm 1/2" 12.7 A5 -- A5 -- -- - - Approved Finishes and "A" Dimensions 1 - Chrome-EnloyO or White Polyester sprinkler with a Chrome-EnIo or White Polyester Sleeve Approved Temperature Ratings and Escutcheon with "A" dimensions 1-1/2" to 45-1/2" (38.1 mm to 1,156 mm) A - 155 °F (68 °C), 175 °F (79°C), 200 °F (93 °C), 2 - Chrome-Enloy® or White Polyester sprinkler with a Chrome-Enloy® Sleeve and Escutcheon and 286 °F (141 °C) with "A" dimensions 1-1/2" to 45-1/2" (38.1 mm to 1,156 mm) B - 155°F (68 °C), 175 °F (79°C), and 200 °F (93 °C) Chrome-Enloy® with "A" dimensions 1-1/2" to 45-1/2" (38.1 mm to 1,156 mm) Chrome-Enloy® or White Polyester with "A" dimensions 3-1/4" to 47-1/2" (82.5 mm to 1,207 mm) 5 - Chrome-Enloy® or Brass with "A" dimensions 3" to 47" (76.2 mm to 1,194 mm) Footnotes 1 Part number shown is the base part number. For complete part number, refer to current Viking price list schedule. 2 K-Factor applies for standard lengths ("A" Dimensions indicated above). Metric K-factor measurement shown is when pressure is measured in Bar. When pressure is measured in kPa, divide the metric K-factor shown by 10.0. This chart shows the listings and approvals available at the time of printing. Other approvals may be in process. Check with the manufacturer for any additional approvals. Listed by Underwriter's Laboratories for use in the U.S. and Canada. 6 Accepted for use, City of New York Department of Buildings, MEA 89-92-E, Vol. 37. 7( (Certified, Standard EN 12259-1, EC-certificate of conformity 0832-CPD-2001. GMED Certified, Standard EN 12259-1, EC-certificate of conformity 0832-MED-1003. Step 1: Carefully slide the wrench sideways around the sprinkler deflector, April 24, 2009 Sprinkler 101e STANDARD RESPONSE N I KJ t%1Gi DRY PENDENT SPRINKLERS The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com DESIGN CRITERIA (Also refer to the Approval Chart on page bid.) NOTE: When using CPVC fittings with Viking dry sprinklers, use only new Nibco Model 5012-S-131 tees. When selecting other CPVC fittings, contact Viking Technical Services. cULus Listing Requirements: Standard Dry Pendent Sprinklers are cULus Listed as indicated in the Approval Chart for installation in accordance with the latest edition of NFPA 13 for standard spray pendent sprinklers. Designed for use in Light, Ordinary, and Extra Hazard occupancies. Protection areas and maximum spacing shall be in accordance with the tables provided in NFPA 13. Minimum spacing allowed is 6 ft. (1.8 m) unless baffles are installed in accordance with NFPA 13. Locate no less than 4" (102 mm) from walls. Maximum distance from walls shall be no more than one-half of the allowable distance between sprinklers. The distance shall be measured perpendicular to the wall. The sprinkler installation and obstruction rules contained in NFPA 13 for standard spray pendent sprinklers must be followed. FM Aooroval Requirements: Standard Dry Pendent Sprinklers are FM Approved as indicated in the Approval Chart for installation in accordance with the latest applicable FM Loss Prevention Data Sheets (including 2-8N) and Technical Advisory Bulletins. FM Global Loss Prevention Data Sheets and Technical Advisory Bulletins contain guidelines relating to, but not limited to: minimum water supply requirements, hydraulic design, ceiling slope and obstructions, minimum and maximum allowable spacing, and deflector distance below the ceiling. NOTE: The FM installation guidelines may differ from cULus and/or NFPA criteria. IMPORTANT: Always refer to Bulletin Form No. F_091699 - Care and Handling of Sprinklers. Also refer to page DRYI-3 for general care, installation, and maintenance information. Viking sprinklers are to be installed in ac- cordance with the latest edition of Viking technical data, the appropriate standards of NFPA, FM Global, LPCB, APSAD, VdS or other similar organizations, and also with the provisions of governmental codes, ordinances, and standards, whenever applicable. Wrench 07565//BwiE must be used for installing recessed dry sprinklers w*A 1/2" ratchet is required (not available from Vikinq), Step 21 Carefully press the wrench upward and turn slightly to ensure engagement with the sprinkler wrench flats. Figure 2: Wrench 07565W/B for Adjustable Recessed Dry Pendent Sprinklers Sprinkler 101 April 24, 2009 STANDARD RESPONSE Me*"l IslII[sU'Lif DRY PENDENT SPRINKLERS The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-818-1680 Email: techsvcsvikingcorp.com For "A' Dimension: 1. Determine the distance from the face of the tee to the finished ceiling, 2. Round to the nearest 1/2" (12.7 mm) between 1-1/2' and 45-1/2' (38.1 mm and 1,156 mm), NOTE The deflector will be located approximately 3-7/16' (87,3 mm) below the ceiling. with 1' (25.4 mm) upward and 1' (25.4 mm) downward adjustment. Deflector at minimum distance below ceiling. 2-7 /16' (61.9 mm) — Minimum ceiling opening _J MP) diameter: 1-3/4" (44.5 mm). Maximum ceiling hole diameter: 2-1/4' (57 mm), NOTE: To locate the deflector at the minimum distance below the ceiling, with no upward adjustment available, order the dry pendent sprinkler 1" (25.4 mm) shorter than the A dimension. - 13/16' (20,6 mm) 1-1/2' --' I Sleeve finish (38.1 mm) matches diameter escutcheon 3-1/16" (77.8 mm) — NOTE: To locate the deflector -1' at the maximum distance I 4-7/16' below the ceiling, with no (112.7 mm) downward adjustment available, .i) Maximum order the dry pendent I sprinkler 1' (25,4 mm) longer than the A dimension. Finished Ceiling Deflector at maximum distance below ceiling. Figure 3: Adjustable Standard Dry Pendent Sprinkler Minimum ceRing h 2-1/8" (54 mm) c Maximum ceihng b 2-1/2" (63,5 mr)) Adjustment: 5/16' (7.9 mr 5/16" (7.9 mr Minimum; 1' (25.4 m Maximum; 1-5/8' (42.1 mm) April 24, 2009 Sprinkler big STANDARD RESPONSE N I KJ W*J DRY PENDENT SPRINKLERS The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058 Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-818-1680 Email: techsvcsvikingcorp.com For, "A" Dimension Determine the distance from face A of tee to finished cei(ing. Round to nearest 1/4" (6,35 mr)) between 3-1/4' (82.5 mm) and 47-1/2' (1,219 mm). JDTE; Sprinkler will be recessed ap- proximately 5/16' (7.9 mm) above finished ceiling with 5/8" (15.8 mm) vertical adjustment available, ished ceiling Figure 4: Adjustable Recessed Dry Pendent Sprinkler For 'A' Dimen---;ion: Outside - dne'ter: '. j I De'ternHe distance £ron face of' 'the (33,4 mm) tee, to the base ,some as 1" of the sprinkler. (25 mm) l 2. Round AD 'to next Schedule i higher 1/2' (12.7 mm) 40 pipe), increment between 3' (76.2 mn) and 47' (1,194 mm). 15/8" (48.3 mm) U.S. K-Factor Metric K-Factor :LIJ.,............................J115.2 I •••••u•••u••uuu••iiuii••••i•• ••u••uu•u•u•uauuui•••i•iuu•u .............................. ••••u•••••u••uauuuus••u••••• u••••••••u••m•u•i•uuu•uuuu•u uu••u•u••aaii•u•m•u•uu•uu•• u•ua••uu•u•uuu•••••uuuui•• ••uuuu •U Ui•UU•UUUUUUUUUUUUUUUlUUUU•IUUtIrw UU•U•UUUUUUU•••U•L•U••UU••U•U• ........................U..U. UUUUUUU••UUUUUU•UUUUUUUUUI•U ••••••••••••••••••••••••••••• ••UU••U•UU•UUUUUUUUUIUUUU•LJU ••..•.•..•...••..•.••.•u.•u••• _U UUIIII ma UUUIUUU •J:I. Figure 5: Plain Barrel Dry Pendent Sprinkler Minimum Recommendedw Temperature Distance From In Face of Tee to Freezer Top of Freezer -20 'F 12 inches <-29 'C> (300 mm) -40 'F 18 Inches (-40 'C) (450 mm) -60 'F 24 Inches (-51 'C) (600 mm) Based on Industry practice Freezer Ceiling 1-1/2' (38.1 mm) diameter 3-1/16 2-7/16' (61.9 mm) Up to 2' (50.8 mm) adjustment available, Note To locate deflector at minimum distance below ceiling, with no upward adjustment available, order the dry pendent sprinklei 1' (25.4 mm) shorter than 'A' dimension. Sprinkler 101h April 24, 2009 STANDARD RESPONSE I(1 t"1Gi DRY PENDENT SPRINKLERS The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Instal . '1 inch NPT threaded end of dry pendent sprinkler PE? Into the 1 Inch NPT outlet of a malleable iron -tee fitting per ANSI B 16.3 (C1o5s 150) or cast iron threaded -tee fitting per ANSI 16.4 (Class 125) only. Minimum ceiling opening diameter 1-3/4' (44,45 mm) "Maximum ceiling opening diameter, 2-1/4' (57 mm). Seat the clearance space around the sprinkler to avoid leakage of air into the freezer area and 13/16' consequent formation of condensate around the to Figure 8 below. 20,6 mm) frame, which could inhibit operation or cause pre- mature operation. Refer N— Sleeve finish matches If humidity and temp- erature differential escutcheon causes condensation on the exposed dry sprinkler, consider wrapping the exposed barrel with insulation, foam insulating tape, or equivalent. Deflector at minimum distance below ceiling Note To locate deflector at maximum distance below the ceiling, with no downward adjustment avail- 4 -7/16 able, order the dry .7 mm) pendent sprinkler Maximum 1' (25,4 mm) longer than 'A' dimension. Deflector at maximum distance below ceiling Figure 7: Dry Pendent Sprinkler Installation in Freezers (Adjustable Standard Dry Pendent Sprinkler is Shown) Figure 8: Dry Sprinkler Seal (Adjustable Standard Dry Pendent Sprinkler is Shown) Form No. F_071591 Replaces page 101a-h, dated April 10, 2009. (Added note regarding CPVC tee fittings.) March 14, 2008 Sprinkler 41a MICROFAST® AND sJIF(JIS1Gj I:II[.Yu.7M MicrofastHP® QUICK RESPONSE PENDENT SPRINKLERS The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-818-1680 Email: techsvcsvikingcorp.com DESCRIPTION Viking Microfast® and MicrofastHP® Quick Response Pendent Sprinklers are small, thermosensitive, glass-bulb spray sprinklers available in several different finishes and temperature ratings and K-Factors to meet design requirements. The special Polyester and Teflon® coatings can be used in decorative applications where colors are desired. In addition, these coatings have been investigated for installation in corrosive at- mospheres and are cULus listed as corrosion resistant as indicated in the Approval Chart, (Note: FM Global has no approval classification for Teflon® and Polyester coat- ings as corrosion resistant.) LISTINGS AND APPROVALS cULus Listed: Category VNIV FM Approved: Class 2020 MV ' A A t, I -..-J,.... ki, ......A....... ........ .. - u i . uvu. il iUdl iui iuei I -i ci-SA dl IU vic - ott-iz-, voiume ID ABS Certified: Certificate 04-H5407984C-PDA VdS Approved: Certificate G4040095, G4040097, G4060056, G4060057, G4880045, G4930038, and G4980021 LPC Approved: Ref. No. 096e/03 and 096e/04 CE Certified: Standard EN 12259-1, EC-certificate of conformity 0832-CPD-2001, 0832-CPD-2003, 0786-CPD-40130, and 0786-CPD-40170 MED Certified: Standard EN 12259-1, EC-certificate of conformity 0832-MED-1003 and 0832-MED-1008 NOTE: Other International approval certificates are available upon request. Refer to the Approval Chart on page 41d and Design Criteria on page 41e for cULus and FM approval requirements that must be followed. TECHNICAL DATA Specifications: Available since 1987. Minimum Operating Pressure: 7 psi (0.5 bar) Maximum Working Pressure: Sprinklers 12282 and 12290 are rated for use with water working pressures ranging from the minimum 7 psi (0.5 bar) up to 250 psi (17 bar) for high-pressure systems. High-pres- sure (HP) sprinklers can be identified by locating "250" stamped on the deflector. All other Part Nos. not mentioned above are rated to a maximum 175 psi (12 bar) wwp. Factory tested hydrostatically to 500 psi (34.5 bar) Testing: U.S.A. Patent No. 4,831,870 Thread size: Refer to the Approval Chart Nominal K-Factor: Refer to the Approval Chart Glass-bulb fluid temperature rated to -65 °F (-55 AC) Overall Length: Refer to the Approval Chart Viking Technical Data may be found on The Viking Corporation's Web site at http:/Iwww.vikinggroupinc.com. The Web site may include a more recent edition of this Technical Data Page. Material Standards: Frame Casting: Brass UNS-C84400 Deflector: Phosphor Bronze UNS-051000 or Copper UNS-C19500 for Sprinklers 06662B, 06666B, 06765B, and 12104. Copper UNS-C19500 for Sprinkler 12282. Brass UNS-C26000 for all other Sprinklers. Bushing (for Sprinklers 06718B, 06720B, and 12290): Brass UNS-C36000 Bulb: Glass, nominal 3 mm diameter Belleville Spring Sealing Assembly: Nickel Alloy, coated on both sides with Teflon Tape Screw: Brass UNS-C36000 Pip Cap and Insert Assembly: Copper UNS-C11000 and Stainless Steel UNS-530400 Pip Cap Attachment: Brass UNS-C36000 Ejector Spring (for Sprinkler 12104): Stainless Steel Form No. F_081296 Replaces page 41a-f, dated October 12, 2007. (Added LPCB Approval and updated CE Approval for Sprinkler 0666613, Added Dry System note in approval chart for Small Orifice.) Sprinkler 41 b March 14, 2008 MICROFAST® AND .J 11(1 I1Gu l:II[.qi.,yM MicrofastHP® QUICK RESPONSE PENDENT SPRINKLERS The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-945-4495 Email: techsvcs©vikingcorp.com For TeflonO Coated Sprinklers: Belleville Spring-Exposed, Screw-Nickel Plated, Pip Cap-TeflonO Coated For Polyester Coated Sorinklers: Belleville Spring-Exposed Ordering Information: (Also refer to the current Viking price list.) Order Microfast® and MicrofastHP® Quick Response Pendent Sprinklers by first adding the appropriate suffix for the sprinkler fin- ish and then the appropriate suffix for the temperature rating to the sprinkler base part number. Finish Suffix: Brass = A, Chrome-Enloy® = F, White Polyester = M-AN, Black Polyester = M-/B, and Black Teflon® = N Temperature Suffix (°F/°C): 135°/68° = A, 155°I68° = B, 175°/79° = D, 200°/93 = E, and 286°/141° = G For example, sprinkler VK302 with a 1/2" thread, Brass finish and a 155 ¶168 "C temperature rating = Part No. 066628AB Available Finishes And Temperature Ratings: Refer to Table 1 Accessories: (Also refer to the "Sprinkler Accessories" section of the Viking data book.) Sprinkler Wrenches: Standard Wrench: Part No. 10896W/B (available since 2000). Wrench for coated and/or recessed sprinklers: Part No. 12144W/B** (available since 2003) NOTE: RECESSED PENDENT SPRINKLERS WITH PROTECTIVE CAPS MUST USE WRENCH 12144W/B. **A 1/2 ratchet is required (not available from Viking). Sprinkler Cabinets: Six-head capacity: Part No. 01724A (available since 1971) Twelve-head capacity: Part No. 01725A (available since 1971) INSTALLATION Refer to appropriate NFPA Installation Standards. OPERATION During fire conditions, the heat-sensitive liquid in the glass bulb expands, causing the glass to shatter, releasing the pip cap and sealing spring assembly. Water flowing through the sprinkler orifice strikes the sprinkler deflector, forming a uniform spray pattern to extinguish or control the fire. INSPECTIONS, TESTS AND MAINTENANCE Refer to NFPA 25 for Inspection, Testing and Maintenance requirements. AVAILABILITY The Viking Microfast® and MicrofastHP® Quick Response Pendent Sprinklers are available through a network of domestic and international distributors. See The Viking Corporation web site for the closest distributor or contact The Viking Corporation. GUARANTEE For details of warranty, refer to Viking's current list price schedule or contact Viking directly. Wrench Fla ts Sprinkler' Protective Cap 10896 Figure 1: Standard Sprinkler Wrench 10896W/B U I - Sprinkler Wrench 12144W/B** For installing coated and/or recessed pendent sprinklers with protective caps. **A 1/2' ratchet is required (not available from Viking). Carefully slide the wrench sideways around the protective caps ensuring engage- ment with the sprinkler wrench flats. March 14, 2008 Sprinkler 41c MICROFAST® AND -J I II I'1G MicrofastHP® QUICK RESPONSE PENDENT SPRINKLERS The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-945-4495 Email: techsvcsvikingcorp.com TABLE 1: AVAILABLE SPRINKLER TEMPERATURE RATINGS AND FINISHES Sprinkler Temperature Sprinkler Nominal Maximum Ambient Classification Temperature Rating' Ceiling Temperature' Bulb Color U Ordinary 135°F(57°C) 100°F(38°C) Orange Ordinary 155°F(68°C) 100°F(38°C) Red Intermediate 175°F (79 , 00) 150°F (65 00) Yellow Intermediate 200 °F (93 °C) 150 °F (65 °C) Green High 286 °F (141 °C) , , 225 °F (107 °C) Blue Sprinkler Finishes: Brass, Chrome-Enloy®, White Polyester, Black Polyester, and Black Teflon® Corrosion-Resistant Coatings4: White Polyester, Black Polyester, and Black Teflon® Footnotes 1 The sprinkler temperature rating is stamped on the deflector. 2 Based on NFPA-13. Other limits may apply, depending on fire loading, sprinkler location, and other requirements of the Authority Having Jurisdiction. Refer to specific installation standards. The corrosion-resistant coatings have passed the standard corrosion test required by the approving agencies indicated on pages 41d. These tests cannot and do not represent all possible corrosive environments. Prior to installation, verify through the end-user that the coatings are compatible with or suitable for the proposed environment. For automatic sprinklers, the coatings indicated are applied to the exposed exterior surfaces only. Note that the spring is exposed on sprinklers with Polyester and Teflon® coatings. Figure 2: Wrench 12144W/B for Coated and/or Recessed Pendent Sprinklers Sprinkler 41d March 14, 2008 MICROFAST® AND MicrofastHP® QUICK 4I I KJ RESPONSE PENDENT SPRINKLERS The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945.9501 Technical Services 877-384.5464 Fax: 269-945-4495 Email: techsvcsvikingcorp.com Approval Chart Ternperaure r KEY I Microfast and MicrofastHPQuick Response Pendent Sprinklers AlX4- So' Maximum 175 PSI (12 bar) WWP Sprinkler Thread Size Nominal Overall Listings and Approvals' Base SIN ___ K-Factor Length (Refer also to Design Criteria on page 41e.) Part No.' NPT BSP U.S. metric2 Inches mm cULus4 FM5 J NYC6 VdS LPCB Standard Orifice 06662B VK302 1/2" 15 mm 5.6 80.6 2-1/4" 58 [Aix, B1Y I A3X, 133Y I AiX, B1Y A3 A3X, 133Y C3X, E3Y13 C3X, E3Y15 Large Orifice 06666B VK352 3/4" 20 mm 80 115.2 2-3/8" 60 AiX, B1Y A2x, 132Y Aix, B1Y -- A3X C3'3 -- 12104 VK352 3/4" 20 mm 8.0 115.2 2-1/4" 58 -- - -- G3 -- -- -- 06765B VK352 1/2 15 mm 8.0 115.2 2-3/8" 60 AiX, B1Y Aix, B1Y A3 -- -- -- Small Orifice' 06718B11 VK329 1/2" 15 mm 2.8 40.3 2-3/16" 56 AiX, B1Y A2X Aix, BiY -- -- -- - 06720B1° VK331 1/2" 15 mm 42 60.5 2-1/4" 58 AiX, B1Y -- AiX, B1Y -- -- -- -- 06932B VK331 -- 10 mm 4.2 60.5 2-3/8" 60 -- -- -- A3 -- G214 -- Maximum 250 PSI (17 bar) WWP Standard Orifice Sprinkler Thread Size Nominal Overall Listings and Approvals' Base SIN - K-Factor Length (Refer also to Design Criteria onpage 41e.) Part No' NPT BSP U.S. metric2 Inches mm cULu54 FM NYC" VdS LPCB 12282 VK317 1/2" 15 mm 5.6 80.6 2-1/4" 58 AiX, B1Y - AiX -- -- -- -- Maximum 250 PSI (17 bar) WWP Small Orifice9 1229010 1 VK342 1/2" 1 15 mm 2.8 J 40.3 1 2-3/16" 56 1 AiX, B1Y - Aix -- -- -- -- Approved Temperature Ratings Approved Escutcheons A- 135 "F (57 "C), 155 "F (68 "C), 175 "F (79 "C), 200°F (93 "C), Approved Finishes x - Standard surface-mounted escutcheon or 8 - 135 °F (57 0c 155° (68 °C) 175 °F (79 "C) and 200 "F (93 °C) 1 - Brass, Chrome-Enloy', White Poly- the Viking Microfast Model F-i Adjustable C - 155 "F (68 CC), 175 "F (79 °C), 200 "F (93 "C), and 286 "F ester18, Black Polyester70, and Black Escutcheon 2 (141 "C) Teflon"' Y - Standard surface-mounted escutcheon or D - 135 "F (57 "C), 155 °F (68 "C), 175 °F (79 "C), and 286 °F 2 - Brass and Chrome-Enloy the Viking Microfast® Model F-i Adjustable (141 °C) 3- Brass, Chrome-Enloy, White Polyester6, Escutcheon 12 or recessed with the Viking -F I 155 68 : and Black Polyester8 Micromatic Model E-1 or E-2 Recessed G - 155 "F (68 °C) Escutcheon Footnotes Base part number is shown. For complete part number, refer to Viking's current price schedule. 2 Metric K-factor measurement shown is when pressure is measured in Bar. When pressure is measured in kPa, divide the metric K-factor shown by 10.0. This table shows the listings and approvals available at the time of printing. Check with the manufacturer for any additional approvals. Listed by Underwriters Laboratories Inc. for use in the U.S. and Canada. FM Approved for use only in wet-pipe sprinkler systems (or preaction systems qualifying as wet systems) for protection of occupancies described in the Factory Mutual Engineering and Research Loss Prevention Data Sheets and Technical Advisory Bulletins. 6 Accepted for use, City of New York Board of Standards and Appeals, Calendar Number 219-76-SA. cULus Listed as corrosion resistant. 8 Other colors are available on request with the same Listings and Approvals as the standard colors. Listings and Approvals limited to Light Hazard Occupancies where allowed by the installation standards being applied, with hydraulically calculated wet systems only. Exception: 4.2K sprinklers may be installed on hydraulically calculated dry pipe systems where piping is corrosion resistant or internally galvanized. '°The sprinkler orifice is bushed. "Accepted for use, City of New York Department of Buildings, MEA Number 89-92-E, Vol. 16. 12The Viking Microfast® Model F-i Adjustable Escutcheon is considered a surface-mounted escutcheon because it does not allow the fusible element of the sprinkler to be recessed behind the face of the wall or ceiling. 13(( Certified, Standard EN 12259-1, EC 0832-CPD-2001 -certificate of conformity and 0832-CPD-2003. 14 CE Certified, Standard EN 12259-1, EC-certificate of conformity 0786-CPD-40130 and 0786-CPD-40170. MED Certified, Standard EN 12259-1, EC-certificate of conformity 0832-MED-1 003 and 0832-MED-1008. Installed with a standard 1/8' surface- mounted escutcheon, 1/2' NPT (15 mm) 2-1/4' 1-5/8' (58 mm) (41 mm) Pendent Sprinkler 06662B (VK302) 1-3/4' (44,5 mm) t cr 2' \II II II! 1-1/2' (381 mm) (50,8 mm) 'ilk Minimum Maximum L Installed with a Micr'ofast Maclet F-I Adjustable Escutcheon March 14, 2008 Sprinkler 41e MICROFAST® AND '4iI I IJ l:II['7M MicrofastHP® QUICK RESPONSE PENDENT SPRINKLERS The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-945-4495 Email: techsvcs©vikingcorp.com DESIGN CRITERIA (Also refer to the Approval Chart on page 41 d) cULus Listing Requirements: Microfast and MicrofastHP11 Quick Response Pendent Sprinklers are cULus Listed as indicated in the Approval Chart for installation in accordance with the latest edition of NFPA 13 for standard spray sprinklers. Designed for use in Light and Ordinary Hazard occupancies (exception: small orifice sprinklers are limited to Light Hazard where allowed by the installation standards being applied, with hydraulically calculated wet systems only). The sprinkler installation rules contained in NFPA 13 for standard spray pendent sprinklers must be followed. FM Aooroval Requirements: For installation in accordance with the latest applicable FM Loss Prevention Data Sheets (including 2-8N) and Technical Advisory Bulletins, FM Global Loss Prevention Data Sheets and Technical Advisory Bulletins contain guidelines relating to, but not limited to: minimum water supply requirements, hydraulic design, ceiling slope and obstructions, minimum and maximum allowable spacing, and deflector distance below the ceiling. NOTE: The FM installation guidelines may differ from cULus and/or NFPA criteria. IMPORTANT: Always refer to Bulletin Form No. F_091699 - Care and Handling of Sprinklers. Also refer to page QRI-3 for general care, installation, and maintenance information. Viking sprinklers are to be installed in ac- cordance with the latest edition of Viking technical data, the appropriate standards of NFPA, FM Global, LPCB, APSAD, VdS or other similar organizations, and also with the provisions of governmental codes, ordinances, and standards, whenever applicable. Ceiling Opening Size: 2-5/16' (58,7 mm) minimum 2-1/8' 2-1/2' (63,5 rim) maximum (54 mm) Figure 3: Sprinkler VK302 Dimensions with a Standard Escutcheon and the Model F-I Adjustable Escutcheon t Sprinkler 41f March 14, 2008 MICROFAST® AND '4jj is,Jf1 ; l:II['7M MicrofastHP® QUICK RESPONSE PENDENT SPRINKLERS The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-945-4495 Email: techsvcsvikingcorp.com I 2-1/8" I Ceiling Opening Size: 2-1/8" I... (54 ) 2-5/16' (58,7 mm) minimum I (54 mm) I 2-1/2" (63.5 mm) maximum 1-3/4' Minimum 1-1/8' (28,6 mm) (44.5 mm) Maximum Installed with a Micromatic Model E-1 Recessed Escutcheon 2' J )f 1-1/8" (28.6 mm) (50,8 m r) \J Minimum Maximum Installed with a thread on Model E-2 Recessed Escutcheon Figure 4: Sprinkler VK302 Dimensions with the Model E-1 and E-2 Recessed Escutcheons Form No. F081296 Replaces page 41a-f, dated October 12, 2007. (Added LPCB Approval and updated CE Approval for Sprinkler 06666B, Added Dry System note in approval chart for Small Orifice.) February 6, 2009 Sprinkler 54a MIRAGE® STANDARD AND QR CONCEALED PENDENT NIKIW*j SPRINKLER VK462 AND HP SPRINKLER VK463 (K5.6) The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-818-1680 Email: techsvcsvikingcorp.com DESCRIPTION Viking Mirage® Standard and Quick Response Concealed Pendent Sprinkler VK462 and HP Sprinkler VK463 are thermosensitive glass-bulb spray sprinklers designed for installa- tion on concealed pipe systems where the appearance of a smooth ceiling is desired. The sprinkler is pre-assembled with a threaded adapter for installation with a low-profile cover assembly that provides up to %" (12.7 mm) of vertical adjustment. The two-piece design allows installation and testing of the sprinkler prior to installation of the cover plate. The "push-on", "thread-off' design of the concealed cover plate assembly allows easy installation of the cover plate after the system has been tested and the ceiling finish has been applied. The cover assembly can be removed and reinstalled, allowing temporary removal of ceiling panels without taking the sprinkler system out of service or removing the sprinkler. LISTINGS AND APPROVALS cULus Listed: Category VNIV FM Approval: Class 2015 NYC Approved: MEA 89-92-E, Volume 32 VdS Approved: Certificate 04080021 LPC Approved: Ref. No. 096e/12 CE Certified: Standard EN 12259-1, EC-certificate of conformity 0832-CPD-2032 Refer to the Approval Chart on page 54c and Design Criteria on page 54d for cULus Listing requirements that must be followed. TECHNICAL DATA Specifications: Available since 2006. Minimum Operating Pressure: 7 psi (0.5 bar)* Viking Technical Data may be found on Maximum Working Pressure: Sprinkler VK463 is rated for use with water working pressures ranging from the minimum 7 psi (0.5 bar) up to The Viking Corporation's Web site at 250 psi (17.2 bar) for high-pressure systems. High-pressure (HP) http://www.vikinggroupinc.com. sprinklers can be identified by locating "250" stamped on the deflec- The Web site may include a more recent tor. Sprinkler VK462 is rated to a maximum 175 psi (12 bar) wwp. edition of this Technical Data Page. Factory tested hydrostatically to 500 psi (34.5 bar) Testing: U.S.A. Patent No. 4,831,870 Thread size: 1/2" (15 mm) NPT Nominal K-Factor: 5.6 U.S. (80.6 metrict) Glass-bulb fluid temperature rated to -65 °F (-55 °C) Patents Pending .cULus Listing, FM Approval, and NFPA 13 installs require a minimum of 7 psi (0.5 bar). The minimum operating pressure for LPCB and CE Approvals ONLY is 5 psi (0.35 bar). tMetnc K-factor measurement shown is when pressure is measured in Bar. When pressure is measured in kPa, divide the metric K-factor shown by 10.0. Material Standards: Sprinkler Body: Brass UNS-C84400 Deflector: Copper UNS-C 19500 for Sprinkler VK462 Phosphor Bronze UNS-051000 for Sprinkler VK463 Deflector Pins: Stainless Steel Alloy Bulb: Glass, nominal 3 mm diameter Pip Cap and Insert Assembly: Copper UNS-C11000 and Stainless Steel UNS-530400 Button: Brass UNS-C36000 Screws: 18-8 Stainless Steel Belleville Spring Sealing Assembly: Nickel Alloy, coated on both sides with Teflon Tape Yoke: Phosphor Bronze UNS-051000 Cover Adapter: Cold Rolled Steel UNS-G10080, Finish: Clear Chromate over Zinc Plating Form No. F 103005 Replaces page 54a-e, dated Sept. 12, 2008. (Added VdS Approval for Sprinkler 13503 with cover 13504). Sprinkler 54b February 6, 2009 "s4 MIRAGE® STANDARD AND QR CONCEALED PENDENT J SPRINKLER VK462 AND HP SPRINKLER VK463 (K5.6) The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058 Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-945-4495 Email: techsvcs@vikingcorp.com Cover Assembly Materials: Cover: Copper UNS-C11000 Base: Brass UNS-C26000 or UNS-C26800 Springs: Nickel Alloy Solder: Eutectic Ordering Information: (Also refer to the current Viking price list.) Viking Mirage® Standard and Quick Response Concealed Pendent Sprinklers and Cover Plate Assemblies must be ordered separately: Sprinkler: Base Part No. 13503A, 14697A, or HP Base Part No. 13667A Specify sprinkler temperature rating by adding the appropriate suffix for the temperature rating to the base part number: Temperature Suffix ("F/°C): 155°/68° = B, 175°/79" = D, 200"/93" = E For example, sprinkler VK463 with a 155 "Ff68 "C temperature rating = 13667AB. Cover Plate Assembly: Base Part No. 13504 (2-3/4" diameter), Base Part No. 13642 (3-5/16 diameter), or Base Part No. 15394 (square cover plate, 3-5/16" diameter) Specify finish and temperature rating of the cover plate assembly by first adding the appropriate suffix for the finish and then the appropriate suffix for the cover temperature rating to the base part number: Finish Suffix: Polished Chrome = F, Painted White = M4SW1004, Painted Ivory = M45W1634, Painted Black = M-/SW1007 Temperature Suffix (°F/°C): 135"/57" UL (139°/59° FM) A, 165°/74° = C For example, cover 13504 with a Polished Chrome finish and a 165 "Ff74 °C temperature rating = 1350417C. Note: Square cover plate 15394 cULus Listing is for the 135 °F (57 "C) temperature rated cover plate only. Refer to the Approval Chart. Available Finishes And Temperature Ratings: Refer to Table 1 Accessories: (Also refer to the Sprinkler Accessories" section of the Viking data book.) Sprinkler Wrenches**: Heavy Duty Wrench Part No. 14047W/B (available since 2006), or Head Cabinet Wrench Part No. 14031*** (available since 2006) Optional Concealed Cover Plate Installer Tool Part No. 14412 for cover 13504, or Part No. 14867 for the large diameter cover (available since 2007) ""Requires a /2" ratchet (not available from Viking). """Optional for removal of the protective cap. Ideal for sprinkler cabinets. Sprinkler Cabinet: Part No. 01731A, Capacity: five (5) sprinklers (available since 1971) INSTALLATION Refer to appropriate NFPA Installation Standards. OPERATION During fire conditions, when the temperature around the sprinkler approaches its operating temperature, the cover plate detaches. Continued heating of the exposed sprinkler causes the heat-sensitive liquid in the glass bulb to expand and the bulb to shatter, releasing the yoke, pip-cap and sealing spring assembly. Water flowing through the sprinkler orifice strikes the sprinkler deflector, forming a uniform spray pattern to extinguish or control the fire. INSPECTIONS, TESTS AND MAINTENANCE Refer to NFPA 25 for Inspection, Testing and Maintenance requirements. AVAILABILITY Viking Sprinklers VK462 and VK463 are available through a network of domestic and international distributors. See The Viking Corporation web site for the closest distributor or contact The Viking Corporation. GUARANTEE For details of warranty, refer to Viking's current list price schedule or contact Viking directly. February 6, 2009 Sprinkler 54c MIRAGE® STANDARD AND QR CONCEALED PENDENT 4J 111F1G SPRINKLER VK462 AND HP SPRINKLER VK463 (K5.6) The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-945-4495 Email: techsvcsvikingcorp.com Approval Chart I ii Mirage Concealed Pendent Sprinklers VK462 and VK463 Sprinkler NPT Nominal Maximum OvetII Length Listings and Approvals' Base SIN Thread K-Factor Water Working (Sprinkler (Refer also to Design Criteria on page 54d.) Size Part No.' Pressure Inch) mm U.S. metric2 Inches I mm cULus' I FM I NYC6 I VdS 1 LPCB (E Standard Response Applications 13503A I VK462 1/2J15 E6 1 80.6 1 175 psi (12 bar) 2-3/16" 1 56 1 AU1, BX11 [AY1, CZ1 I -J - 14697A 1Y 1/2115 5.6 1 80.6 1 175 psi (12 bar) 2-3/16' 1 56 1 - AV2, BW2IAV2, BW2 Quick Response Applications 13503A [VK462 1/2' 15 5.6 80.6 175 psi (12 bar) 2-3/16" 56 AV1, BX1 -- {vi, BW1 - - - 14697A 1VK462 1/2" 15 5.6 80.6 175 psi (12 bar) 2-3/16" 56 AV1, BX1 -- AV1, BW1 - - 13667A 1VK463 1/2" 15 5.6 80.6 250 psi (17.2 bar)3 2-3/16"1 56 AV1, BX1 -- AV1, BW1 -- -- -- Cover Plate Assembly Temperature Ratings' U - 135 °F (57 "C) cULus Listed cover 135041, 13642 (large diameter), or 153941 (square cover plate) Sprinkler Temperature Ratings FM Approved as 139 °F(59 "C) - 155 r -) V - 135 °F (57 °C) cULus Listed cover 135041 or Finishes of the Cover Plate Assembly' B - 175 F (79 C) and 200 F 136421 (large diameter) W - 165 "F (74 "C) cover 135041 or 136421 (large 1 - Polished Chrome, Painted White, Painted Ivory, or Painted Black (93 C) diameter) 2 - Polished Chrome, Painted White C - 200 °F (93 °C) X - 165 "F (74 °C) cover 135041, 136421 (large diam- eter), or 153941 (square cover plate) Y - 135 "F (57 "C) cover 135041 Z - 165 "F (74 °C) cover 135041 Footnotes 1 Part number shown is the base part number. For complete part number, refer to current Viking price list schedule. 2 Metric K-factor measurement shown is when pressure is measured in Bar. When pressure is measured in kPa, divide the metric K-factor shown by 10.0. The Water Working Pressure rating is stamped on the deflector. This chart shows the listings and approvals available at the time of printing. Other approvals may be in process. Check with the manufacturer for any additional approvals. Listed by Underwriter's Laboratories for use in the U.S. and Canada. Accepted for use, City of New York Department of Buildings, MEA Number 89-92-E, Vol. 32. CE Certified, Standard EN 12259-1, EC-certificate of conformity 0832-CPD-2032. The 135/139 "F cover has an orange label. The 165 °F cover has a white label. Painted finish consists of Polyester Baked Enamel. Other paint colors are available on request with the same listings as the standard paint colors. Listings and approvals apply for any paint manufacturer. Contact Viking for additional information. NOTE: Custom colors are indicated on a label inside the cover assembly. Refer to Figure 1. TABLE 1: SPRINKLER TEMPERATURE Sprinkler Temperature Sprinkler Nominal Maximum Ambient Temperature Rating of Cover Bulb Color Classification Temperature Rating' Ceiling Temperature' Assembly (Required) Ordinary 155 F (68 0 C) 0 0 100 F (38 C) 135"F(57 °C)cULus Red °F °C) 139 (59 FM Intermediate 175 "F (79 °C) 150 "F (65 00) 165 "F (74 °C) Yellow Intermediate 200 °F (93 00) 150 "F (65 °C) 165 OF (74 00) Green Cover Plate Finishes: Polished Chrome, Painted White, Painted Ivory, or Painted Black Footnotes The sprinkler temperature rating is stamped on the sprinkler deflector. 2 Based on NFPA-13. Other limits may apply, depending on fire loading, sprinkler location, and other requirements of the Authority Having Jurisdiction. Refer to specific installation standards. Sprinkler 54d February 6, 2009 MIRAGE® STANDARD AND QR CONCEALED PENDENT SPRINKLER VK462 AND HP SPRINKLER VK463 (K5.6) The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-945-4495 Email: techsvcsvikingcorp.com DESIGN CRITERIA (Also refer to the Approval Chart on page 54c.) cULus Listing Reauirements: Mirage5 Standard and Quick Response Concealed Pendent Sprinklers VK462 and VK463 are cULus Listed for installation in accordance with the latest edition of NFPA 13 for standard coverage pendent spray sprinklers as indicated below. For hazard occupancies up to and including Ordinary Hazard, Group II. Protection areas and maximum spacing shall be in accordance with the tables provided in NFPA 13. Maximum spacing allowed is 15 ft. (4.6 m). Minimum spacing allowed is 6 ft. (1.8 m) unless baffles are installed in accordance with NFPA 13. Minimum distance from walls is 4 in. (102 mm). Maximum distance from walls shall be no more than one-half of the allowable distance between sprinklers. The distance shall be measured perpendicular to the wall. The sprinkler obstruction rules contained in NFPA 13 for standard coverage pendent spray sprinklers must be followed. NOTE: Concealed sprinklers must be installed in neutral or negative pressure plenums only. FM Aooroval Reauirements: Mirage Concealed Pendent Sprinkler VK462 is FM Approved as a standard response standard spray sprinkler as indicated in the Approval Chart for hazard occupancies up to and including Ordinary Hazard, Group II. For installation in accordance with the latest applicable FM Loss Prevention Data Sheets (including 2-8N) and Technical Advisory Bulletins. FM Global Loss Prevention Data Sheets and Technical Advisory Bulletins contain guidelines relating to, but not limited to: minimum water supply requirements, hydraulic design, ceiling slope and obstructions, minimum and maximum allowable spacing, and deflector distance below the ceiling. NOTE: The FM installation guidelines may differ from cULus and/or NFPA criteria. IMPORTANT: Always refer to Bulletin Form No. F 091699 - Care and Handling of Sprinklers. Also refer to page SRI-3 or QRI-3 for general care, installation, and maintenance information. Viking sprinklers are to be installed in accordance with the latest edition of Viking technical data, the appropriate standards of NFPA, FM Global, LPCB, APSAD, VdS or other similar organizations, and also with the provisions of governmental codes, ordi- nances, and standards, whenever applicable. CUSTO Identification of Custom Pa int Color All custom color painted cover plates will have an identifying label afffixed to the inside of the cover that indicates custom color and will have a representative sample (a paint dot) of the paint on the label. Figure 1: Identification of Custom Paint Color for Concealed Covers Sprinkler Frame Arms Sprinkler Wrench Flat NEVER install the sprinkler by applying the installation wrench across the frame arms. DO NOT overtighten. Use only the designated sprinkler wrench, Viking Part Number 14047W/B or 14031. 2-1/4" (57,2 mm) diameter opening is required in the ceiling. 1-1 A 1/2' ratchet s required (not itoble from Viking) Sprinkler Wrench (Part No. 047W/B- is shown) 1/2' (15 mm) NPT 2-3/16" EIII 1 (56 mm) L * February 6, 2009 Sprinkler 54e MIRAGE® STANDARD AND QR CONCEALED PENDENT 41KJW*jN SPRINKLER VK462 AND HP SPRINKLER VK463 (K5.6) The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-945-4495 Email: techsvcsvikingcorp.com Step 1: Carefully slide the wrench sideways around the deflector and pins. Step 2 Carefully press the wrench upward and turn slightly to ensure engagement with the sprinkler wrench flats. DO NOT apply more than 25 ft, lbs, of torquie. A leak tight seat should be achieved by turning the sprinkler clockwise 1 to 1-1/2 turns beyond finger tight. Figure 3: Sprinkler Installation and Correct Use of Wrenches 2-3/4" (70 mm) or 3-5/16' (84.1 mm) Note: Upon sprinkler activation, the deflector descends to approximately 13/16" (20.6 mm) below the sprinkler body.