Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
1969 PALOMAR OAKS WAY; ; FPC2017-0033; Permit
[11iIlI i J.]iI ('City of Carlsbad - Print Date: 08/30/2022 Permit No: FPC2017-0033 Job Address: 1969 PALOMAR OAKS WAY, CARLSBAD, CA 92011-1307 Status: Closed - Finaled Permit Type: FIRE-Construction Commercial Work Class: Fixed Extinguishing Syste Parcel #: Track #: Applied: 02/06/2017 Valuation: $0.00 Lot #: Issued: 05/31/2017 Occupancy Group: Project #: Finaled Close Out: 03/09/2021 #of Dwelling Units: Plan #: Bedrooms: Construction Type: Final Inspection: Bathrooms: Orig. Plan Check #: INSPECTOR: Stowe, Daniel Plan Check #: Fieri, Dominic Project Title: Description: AIR PRODUCTS -DRY CHEM SYSTEM (HOOD SUPP SYS) FPContractor: SCHMIDT FIRE PROTECTION CO INC-DO NOT USE 4760 MURPHY CANYON RD SAN DIEGO, CA 92123 (858) 279-6122 FEE AMOUNT FIRE Hood & Duct Extinguishing System Initial Sys $404.00 Total Fees: $404.00 Total Payments To Date: $404.00 Balance Due: $0.00 Fire Department Page 1 of 1 1635 Faraday Avenue, Carlsbad CA 92008-7314 1 760-602-4665 1 760-602-8561 f I www.carlsbadca.gov Air Products 1969 Palomar Way Carlsbad, CA 92009 Kidde Industrial Dry Chemical System Room - 114 Upgrade Phase-11 Exhaust Hood SUBMITTAL PACKAGE Design by: Date Gordon E. Swope SET February 3. 2017 (NICET Level-IV #078621) (619) 871-9753 gordon@schmidtfireprotection.com \ 2e4a . 0 d5eman5 of càe k Kidde XVrM Control System 0 P/N: 87-120099-002 FEATURES For Use in: WHDR" Commercial Cooking Fire Suppression Systems IND Industrial Fire Suppression Systems Pneumatic Release of up to 20 Agent Cylinders Two Discrete Mechanical Detection Lines Cylinder or Wall Mount Up to 400 ft. Mechanical Detection Cable DESCRIPTION Ap Kidde Fire Systems Effective: August 2013 K-87-027 Operates 2 Gas Valves Available 24 V Electrical Actuation Multiple Remote Release Options Rugged, Die-Cast Aluminum Body Tamper/Lock Port for Cover Easy to Install and Maintain UL & ULC Listed FM Approved for IND Systems The Kidde XV Control System is a compact, versatile unit used to actuate agent cylinders on Kidde WHDR and IND Pre-Engineered fire suppression systems. The control head can be operated via: Two Distinct Automatic Mechanical Detection Lines (fusible links or thermo-bulb links) Optional Electrical Solenoid Remote or Local Manual Mechanical Control Upon actuation, the XV Control System discharges the nitrogen System Cartridge, pressurizing the actuation lines and System Valve Actuators (SVA) mounted on the cylinder valve(s). The SVA(s) open the cylinder valve(s), discharging the WHDR wet chemical or IND dry chemical suppression agent. The XV can be mounted on a wall or directly to an SVA mounted on the cylinder. The XV Control System is UL and ULC Listed with WHDR Wet Chemical and IND Dry Chemical Fire Suppression Systems. The XV is FM approved with the IND Dry Chemical Systems. The XV comes ready to install, with three EMT connectors, one System Valve Actuator (SVA), two microswitches, one nitrogen System Cartridge, and one nitrogen test cartridge. fKidde Fire Systems - _'W6 FIRE SUPPRESSION SYEM1 0 Figure 1. XV Control System, PIN 87-120099-002 TECHNICAL DATA Table 1. Mechanical Cable Parameters for WHDR & IND Systems XV Cable Line Max. Cable Length Max. Corner Pulleys Max. Detectors Max. Tee Pulleys Detection and Manual Release-to-Trip Line 1 200 ft. (60.96 m) 50 40 * Detection and Manual Release-to-Trip Line 2 200 ft. (60.96 m) 50 40 * Pull-to-Trip Remote Manual Release Line 100 ft. (30.48 m) 30 - 1* Mechanical Gas Valve Line 100 ft. (30.48 m) 30 - 1* *Tee pulleys count as two Corner Pulleys. Maximum is from XV Control, through the pulley, to each device. Table 2. Actuation Parameters for WHDR Wet Chemical Systems Operating Temperature Number of Extinguishing Maximum Total Length Minimum Total Length of Copper Range System Cylinders Copper Actuation Tubing Actuation Tubing 0°F to 120°F 1-12 106 ft. (32.30 m) (18°C to 49°C) 5 ft. (1.52 m) 13-20 91 ft. (27.73 m) Table 3. Actuation Parameters for IND Industrial Dry Chemical and Open-Face Spray Booth Systems Operating Temperature Number of Extinguishing Maximum Total Length Minimum Total Length of Copper Range System Cylinders Copper Actuation Tubing Actuation Tubing -40°F to 120°F 1-14 166 ft. (50.60 m) 5 ft. (1.52 m) 15-20 121 ft. (36.88 m) (40°C to 49°C) Table 4. Actuation Parameters for IND Dry Chemical for Vehicle Spray Booths Operating Temperature Number of Extinguishing Maximum Total Length Minimum Total Length of Copper Range System Cylinders Copper Actuation Tubing Actuation Tubing 1-8 200 ft. (60.96 m) 0°F to 120°F 9-15 160 ft. (48.76 m) (-18°C to 49°C) 5 ft. (1.52 m) 16-20 140 ft. (42.67 m) NOTES Braided high pressure nitrogen tubing (P/N 87-1 20045-00X), is required to connect the XV Control System to the System Valve Actuator (SVA) when the XV Control System is cylinder mounted. Copper tubing shall be 1/4-inch O.D. x 0.031-inch wall high pressure tubing. When Control System is cylinder mounted and two or more cylinders are being actuated, a minimum of 5 ft. (1.52 m) of 1/4-inch O.D. x 0.031-inch wall tubing shall be used for actuation lines. -2- I 4. When Control System is wall mounted, a minimum of 5 ft. (1.52 m) of 1/4-inch O.D. x 0.031-inch wall tubing shall be used in the overall actuation line. . 5. High pressure nitrogen tubing (P/N 87-120045-OOX) may be used in place of copper tubing, not to exceed a max- imum length of 30 feet (9 m). In every system, either single cylinder or multiple cylinder, a 1/8-inch NPT plug or vent check (PIN WK-877810- 000) shall be used in the outlet port of the last System Valve Actuator(s) in the actuation line. A maximum of 2 Pressure Switches (P/N 486536) may be used in the actuation line. SYSTEM NITROGEN CARTRIDGE, PIN 87-120043-001 The XV Control System uses a nitrogen cartridge for actuating the system cylinders and is charged with dry nitrogen (see Figure 2). The cartridge is mounted inside the XV Control System to protect it from tampering and provides the date of manufacturing and space (gray band) for recording the installation date. GRAY BAND' Figure 2. System Nitrogen Cartridge, PIN 87-120043-001 .TEST CARTRIDGE, P/N 87-120044-001 The Test Cartridge is used for functional testing of the Kidde WHDR Wet Chemical System and IND Dry Chemical System*. The cartridge has a red band and is labeled "TEST CARTRIDGE" as shown in Figure 3. *Note: The System Nitrogen Cartridge PIN 87-120043-001 is required for actuation and full discharge or "puff' tests, and when a time delay is included (as in systems protecting Vehicle Spray Booths). 4 in. (102 mm) 1;n. I I TEST (25 mm) CARTRIDGE Figure 3. Test Cartridge, P/N 87-120044-001 S 1/8 in. NPT PORT 1/8 In. NPT PLUG (IF APPLICABLE) PISTON IN ACTUATED POSITION (TOWARDS CYLINDER VALVE) Figure 4. System Valve Actuator (SVA), P/N 87-120042-001 1-3/4 In. (44 mm) 1 SVA PISTON IN SET POSITION SPRING LOADED PLUNGER HIGH-PRESSURE NITROGEN TUBING, P/N 87-120045-OOX SYSTEM VALVE ACTUATOR (SVA), P/N 87-120042-001 A System Valve Actuator (SVA) must be mounted to every system cylinder valve assembly (see Figure 4). The SVA has ports for low profile tubing runs, and is also equipped with a spring loaded plunger that locks the piston in the discharged position, ensuring complete discharge of the cylinder(s) contents. 5/16-18 UNC THROUGH HOLE (TYP) (NOT SHOWN) The High-Pressure Nitrogen Tubing is used to connect the XV Control System to the SVA on all installations in which the XV Control System is mounted to a wet or dry chemical cylinder. (see Figure 5). A 1/8-inch NPT (male) x 3/8-24 JIC Adapter is included with the High Pressure Nitrogen Tubing. 1/8 in. NPT V1 READ SEAT 1/2 in. HEX, 1/4 in. 37 DEGREE FLARE, SWIVEL A (END TO SEAT) 1/8 in. NPT (MALE) x 3/8-24 JIC ADAPTER Figure 5. External Tubing for XV Control System, P/N 87-120045-OOX Table 5. External Tubing for XV Control System Part Number Length "A't 87-120045-001 7-1/2 in. (191 mm) 87-120045-002 24 in. (610 mm) 87-120045-003 60 in. (1524 mm) -4- S SOLENOID, PIN 83-100034-001 An optional solenoid can be installed into the XV Control System, just under the actuation latch. The solenoid operates directly on the actuation latch to activate the system. This installation allows simultaneous usage of mechanical detection lines, or the lines can be locked out. The solenoid includes two mounting bolts, the bracket and a push plate which mounts onto the solenoid body (Figure 6). The solenoid coil is 24 Vdc at 1.5 Amp and at 70°F (21°C). Refer to Figure 7 for Release Wring with Terminal Type Microswitch. When actuating the XV Control System with an optional solenoid, a UL Compatible and Listed fire control panel with a supervised power supply is required, such as the Kidde AEGIS or Kidde ARIES. PUSH PLATE (DO NOT REMOVE) SOLENOID BODY ALLEN SCREWS (2) TINE BRACKET )T REMOVE) RICAL LEADS 610 mm) Figure 6. Solenoid, P/N 83-100034-001 WIRE TYPE KEY ALARM WIRES TO XV - . - . -. - . - . - SOLENOID AND/OR OTHER DEVICES MICROS WITCH (INTERNAL) ALARM WIRES FROM CONTROL PANEL XVSOLENOD PIN 93 00034-001 24 /DC ONLY ®H2 - RELEASING CIRCUIT IN COMPATIBLE CONTROL SWITCH POSITION WHEN XV FLAG/CAM IS IN SET POSITION Figure 7. Release Wring with Terminal Type Microswitch Note: Where electric detection and/or actuation is pro- vided, supervision shall be provided in accor- dance with NFPA 72, National Fire Alarm and Signaling Code. Alarms and indicators, along with a supervised power source, shall be pro- vided in accordance with NFPA 72. Electrical wir- ing and equipment shall be provided in accordance with NFPA 70, National Electric Code. All installations are subject to the approval of the Authority Having Jurisdiction (AHJ). OPEN TERMINAL 2 FLAG ENGAGED USED /.. BY XV MINAL2NOTU ..IT C..OLENOIDL.ADTO TERMINAL I OF MICROSWITCH COMMON TERMINAL I PANEL 124 VDC ONLY) /L ATTACH RELEASING CIRCUIT TO SPLICE SOLENOID LEAD TERMINAL 4 OF MICROSWITCH CLOSED TERMINAL 4 TO RELEASING CIRCUIT KEEPER PIN, P/N 60-9197108-000 The Keeper Pin (P/N 60-9197108-000) is used to prevent actuation while installing the system. C>~ Figure 8. Keeper Pin, P/N 60-9197108-000 -5- S FIRE SUPPRESSION SYSTEM 9-3/4' (248 mm) 8-1/2" (216 mm) 3-3/4" (95 mm) MOUNTING HOLE MOUNTING HOLE 3, (19 MOUNTING HOLE MOUNTING HOLE (3-4'-' M'") ORDERING INFORMATION Description Part Number XV Control System includes: (1) 87-120042-001 System Valve Actuator (1) 87-120043-001 System Nitrogen Cartridge (1) 87-120044-001 Test Cartridge (1) 87-120058-001 EMT Connector Kit (1) 87-120039-001 Microswitch Kit (1) 87-120039-501 Microswitch Kit 87-120099-002 System Valve Actuator 87-120042-001 System Nitrogen Cartridge 87-120043-001 Test Cartridge 87-120044-001 High Pressure Hose for Cylinder Mount 87-120045-001 EMT Connector Kit 87-120058-001 Solenoid Electric Actuator Kit 83-100034-001 Microswitch Kit (SPDT), Solid Color Leads 87-120039-001 Microswitch Kit (SPDT), Striped Color Leads 87-120039-501 Terminal Type Microswitch Kit (SPDT) 87-120047-001 REFERENCE INFORMATION WHDR Systems designed and installed according to manual P/N 87-122000-001. IND Systems designed and installed according to manual P/N 220423. Vehicle Spray Booth Systems designed and installed according to manual P/N 83-100036-001. Figure 9. XV Control System Dimensions Kidde is a registered trademark of Kidde-Fenwal, Inc. WHDR, IND, XV, AEGIS, and ARIES are trademarks of Kidde-Fenwal, This literature is provided for informational purposes only. KIDDE-FENWAL, INC. I '(idde Fire Systems assumes no responsibility for the product's suitability for a particular application. The 0-.ddw 0 product must be properly applied to work correctly. If you need more information on this product, or if you have a particular question, contact I KIDDE-FENWAL, INC., Ashland, MA 01721. Telephone: (508) 881-2000. 400 Main Street Ashland, MA 01721 Tel.: 508-881-2000 K-87-027 Rev AG © 2013 Kidde-Fenwal Inc. Fax: 508-881-8920 wwwkiddefiresystems.com Kidde IND TM System Actuation Delay (0019, Kidde Fire Systems Effective: December 2013 K-83-037 P/N 83-100035-001 FEATURES Secures to Bottom of XV Control System • Up to 200 ft. 1/4 inch Copper Tubing Meets UL 1254 Requirements for Enclosed Paint Booths • Rugged Nickel Plated Brass Body Easy to Service • Dependable Stainless Steel Stem Flexible Tubing Parameters • UL/ULC Listed for use with all Kidde IND Dry Actuate up to 20 Dry Chemical Cylinders Chemical Cylinders ACTUATION DELA YASSEMBLY Enclosed paint booths require 10 to 20 seconds of actua- tion delay between detection/actuation and release of the agent cylinders. The Kidde XV Control System Actuation Delay (PIN 83-100035-001) provides an easy and ele- gant solution for this requirement. The Actuation Delay attaches directly to the bottom of the XV Control System. It fits within the profile of the XV Con- trol System, protecting it from being damaged by tools and other equipment in the hazard area. The Actuation Delay is made of rugged nickel plated forged brass with a stainless steel actuation stem. This trouble-free design has only one moving part, ensuring reliable, long-term service. The Actuation Delay is easy to install. No intermediary hardware is needed. The System Nitrogen Cartridge (P/N 87-120043-001) of the XV Control System feeds directly into the Actuation Delay. After the proper time, the outlet of the Actuation Delay feeds directly into the System Valve Actuators (SVA, P/N 87-120042-001) on the agent cylinders. The Actuation Delay is designed to complement the XV Control System and agent cylinders, creating a clean, elegant and easy-to-install system. 1/8 IN. NPT INLET FRONT VIEW DUNTING HOLES (2) 16-18 UNC THREAD 1/8 IN. I OUTLE N ACCUMULATOR CAP NITROGEN MUST FLOW IN DIRECTION OF ARROW. FRONT OF ACTUATION DELAY MUST FACE OUT. Figure 1. Actuation Delay Assembly ORDERING INFORMATION Part Number Description 83-100035-001 XV Actuation Delay 87-120045-001 XVActuation Hose (required, included with Actuation Delay) 87-120099-002 XV Control System 87-120043-001 System Nitrogen Cartridge TECHNICAL DATA Figure 2. XV Control System Dimensions with Actuation Delay and Hose Table 1: Actuation Length Limitations Number of Max. Total Mm. Total Extinguishing Length Copper Length Copper System Actuation Actuation Cylinders Tubing Tubing 1-8 200 ft. (60.96 m) 5 ft. (1.52m) 9-15 160 ft. (48.76 m) 16-20 140 ft. (42.67 m) Kidde is a registered trademark of Kidde-Fenwal, Inc. ND is a trademark of Kidde-Fenwal, Inc. This literature is provided for informational purposes only. KIDDE-FENWAL, INC. assumes no responsibility for the product's suitability for a particular application. The product must be properly applied to work correctly. If you need more information on this product, or if you have a particular problem or question, contact KIDDE-FENWAL, INC., Ashland, MA 01721. Telephone: (508) 881-2000. K-83-037 Rev AD © 2013 Kidde-Fenwal Inc. S Kidde Fire 400 Main Street Ashland, MA 01721 Tel.: 508-881-2000 Fax: 508-881-8920 www.kiddefiresystems.com Systems S Installation 4-4.1.1 INSTALLING THE XV CONTROL SYSTEM (WALL MOUNT) 1. With the XV Control System cover removed, lay the box on its back. Locate the four mounting holes in the housing. Position the box so that the mounting holes are not flat on the work surface and break out the knockouts. See Figure 4-7 for location of mounting holes. MOUNTING HOLE MOUNTING MOUNTING HOLE (140 mm) HOLE -Th 11 (954jmm) logl 0 0' I F 4-3/8 in. (112 mm) MOUNTING 1-5/16 in. HOLE (34 mm) Figure 4-7. Location of Mounting Holes (Housing) 3/4 in. (19 mm Using 1/4-20 x 3-inch long toggle bolts or equivalent hangers, mount the box to the wall making sure it is level. Attach the conduit fittings and other fittings to the box. Run cables and wiring as normal, within the parameters of the XV Control System. Locate the System Valve Actuators (SVA). P/N 220423 4-9 January 2007 S SVA PISTOl' SET POSITION Installation 4. Ensure the piston of the SVA is in the 'Set' position. See Figure 4-8. Figure 4-8. SVA in 'Set' Position Remove the Valve Protection Plate from the top of the cylinder valve. Install the SVAs onto each cylinder valve (the piston facing cylinder valve). Do not tighten them as they will be removed at a later time. Install 1/8-inch NPT pipe plug (P/N 877810) or optional vent check on last SVA (end of line). Install 1/8 NPT (M) x 1/4 copper tubing adapters. Compression type adapters are permissible. Measure and install the 1/4 O.D. x 0.031 wall thickness copper tubing. A 2-1/2 inch (64 mm) loop between each cylinder and on the inlet tubing is recommended, but not required. See Figure 4-9. Ensure that each connection is secure. 118 in. PLU OPT" VENT I Figure 4-9. Example of Copper Tubing Loop Method 1. Remove the SVAs from the cylinder valves and re-install the Valve Protection Plates. S January 2007 4-10 P/N 220423 SVA PISTO SET POSITION Installation 4-4.1.2 INSTALLING XV CONTROL SYSTEM (CYLINDER MOUNT) Locate the System Valve Actuators (SVA). Ensure the piston of the SVA is in the 'Set' position. Figure 4-10. SVA in 'Set' Position Remove the Valve Protection Plate from the top of the cylinder valve. Install the SVAs onto each cylinder valve (the piston facing cylinder valve). The ports on the SVA should be positioned towards the discharge adapter. Do not tighten the SVA(s) as it will be removed at a later time. Figure 4-11. XV Control System (Cylinder Mount) Install XV Control System onto the SVA. P/N 220423 4-11 January 2007 Installation 6. Install SVA bolts through the bottom of the XV Control System into the SVA. SVA Figure 4-12. Mounting the XV Control System to the SVA For multiple cylinder installations, install 1/8 NPT (M) x 1/4 copper tubing adapters. Compression type adapters are permissible. For multiple cylinder installations, measure and install the 1/4 O.D. x 0.031 wall thickness copper tubing. A 2-1/2-inch (64 mm) loop between each cylinder and on the inlet tubing is recommended, but not required. See Figure 4-13. Ensure that each connection is secure. Note: Minimum 5 ft. (1.2 m) copper tubing (total). Install the 1/8 NPT (M) x 3/8-24 JIC flare adapter (included with the High Pressure Nitrogen Tubing P/N 87-120045-001) onto the outlet port of the XV Control System. Note: Do not use Teflon tape. January 2007 4-12 P/N 220423 Installation S Figure 4-13. Example of Copper Tubing Loop Method 10. Secure the 3/16-inch braided High Pressure Nitrogen Tubing (P/N 87-120045-001) onto the SVA. Ensure the connection is tight. S A The High Pressure Nitrogen Tubing is required between the "Control System CAUTION and the primary SVA on all cylinder mounted installations. Note: Do not attach the swivel end of the hose onto the outlet of the )(V Control System. CONTROL SYSTEM HIGH PRESSURE NITROGEN TUBING I/B NPT FITTING Figure 4-14. Installing High Pressure Nitrogen Tubing 0 11. Remove the SVAs from the cylinder valves and re-install the valve protection plates. P/N 220423 4-13 January 2007 Installation 4-4.1.3 ACTUATION The next step in the installation process is deciding what type of actuation to use. The XV Control System offers the use of mechanical, electrical or a combination of mechanical and electrical actuation. Mechanical actuation utilizes detectors (fusible, KGR and/or KGS) to detect heat, whereas electrical actuation utilizes heat detectors for detection. Mechanical and electrical actuation can be combined together when configured using a UL Listed fire control panel, such as the Kidde Scorpio1M. Figure 4-15 illustrates the steps to follow when deciding what type of actuation to use. Mechanical Mechanical, electrical Electrical or both? "Mechanical Detec- tion Installation" on page 4-15. Both>H "Mounting The Solenoid, P/N 83-100034-001" on page 4- 28. Includes Lockout of both Detection Lines Installing both Detec- tion Lines? Yes erection No Line 1 or 2 ne1Line2 ".. / See "Cabling Detec- See "Cabling Detec- tion Line 1 Only - tion Line 2 Only Includes Lockout of (Option 1)— Includes Detection Line 2" on Lockout of Detection See "Cabling Mechan- page 4-20. Line 1" on page 4-21. ical Detection - Both Lines" on page 4-18. Note: Refer to the DIOM manual for the specified fire control unit. Figure 4-15. Decision Flow Chart for Actuation January 2007 4-14 P/N 220423 fl Installation 4-4.1.4 MECHANICAL DETECTION INSTALLATION Detectors are to be located in an anticipated path of convective heat flow from a fire, and . spaced at a maximum on-center distance of 20 ft. (6.1 m) for Thermo-Bulb series detectors and 10 ft. (3.1 m) for standard response detectors, for ceiling heights up to 10 ft. (3.1 m) (refer to Chapter 3). The 1/16-inch cable is to be protected by 1/2-inch conduit or electrical metal tubing (EMT). 4-4.1.4.1 Installing Detection Components Drill holes as necessary for installation of the Quick Seal Adapters (P/N 2649930X) or Compression Seal Adapters (P/N 2650460X). 2. Mount the detector brackets as required. A Be sure mounting penetrations are liquid and grease tight. WARNING Install conduit from the XV Control System detector conduit knockout(s) (top or right side of the XV Control System) to the detector brackets using Corner Pulleys (P/N 844648) at all changes in direction. Remove screws and covers from the Corner Pulleys and set aside for reuse later. Note: No bends or offsets are permitted in conduit lines. Be sure the system is adequately supported. Figure 4-16. Unacceptable Cable Configuration Run the 1/16-inch Control Cable from the various system devices, through 1/2-inch EMT conduit, to the XV Control System. P/N 220423 4-15 January 2007 1/16 in. CABLE TO XV CONTROL SYSTEM (NOT SUPPLIED) EXAMPLE OF END-OF-LINE DETECTOR HOUSING KIT Installation Install detectors of proper rating as described in Paragraph 2-3.1.8. To install detectors, follow the steps below. Always start detector installation at the last detector (see Figures 4-17 and 4-18). To install detectors, create a cable loop using a Crimp Sleeve (P/N 214951), and Crimp Tool (P/N 253538). EXAMPLE OF IN-LINE Figure 4-17. Detector Housing Kit, P/N 804548 A Use of a crimp tool besides P/N 253538 can cause malfunction and/or WARNING unwanted discharge of the system. Note: In order to ensure the crimp sleeve is secure, the cable must always be looped so that there are two lengths of cable inside the Crimp Sleeve before crimping. Cable must not be spliced anywhere along its length. Place the Crimp Tool on the end of the sleeve. Ensure the flat of the sleeve rests in the saddle of the Crimp Tool jaw. Secure the sleeve in the tool carefully to ensure the sleeve does not shift in the saddle before pressing. Squeeze the handles of the Crimp Tool until the tool releases itself. The tooth of the jaw is pressing on the wall of the sleeve without cracking the malleable copper. The first crimp is complete. Remove the crimp from the tool. Put the Crimp Tool onto the other end of the sleeve. The sleeve shall be 1800 turned in the tool from the first crimp. Note: This is pressing the loop end of the sleeve (opposite that of the first press). Squeeze the handles of the Crimp Tool until the tool releases itself. The tooth of the jaw is pressing on the wall of the sleeve without cracking the malleable copper. The second crimp is complete. Remove the crimp from the tool. A To ensure proper system operation, each detector must be installed so that at least 1-1/2 inches of cable movement toward the XV Control System is CAUTION maintained. Attach an "S" hook (P/N 87-9189413-000) to the end of the last detector mounting bracket. January 2007 4-16 P/N 220423 Installation Attach proper detector onto the "S" hook. Attach 1/16-inch cable to the hook at the other end of the detector, forming a cable loop held in place by a Crimp Sleeve. Note: If only one detector is used, thread the cable back through the EMT conduit to the XV Control System. If additional detectors are used, attach the cable to each successive detector "S" hook, as described above. After attaching cable to last detector "S" hook, thread cable back through the EMT conduit to the XV Control System. 1/16 in. CABLE TO CONTROL SYSTEM (NOT SUPPLIED) "5" HOOKS CRIMP SLEEVE EXAMPLE OF END-OF-LINE UNIVERSAL HOUSING KIT SPACING REQUIREMENTS XV: 1-1/2 in. (38 mm) MIN. KRS-50: 3 in. (76 mm) MIN. Cr— IV NCRIMP SLEEVE EXAMPLE OF IN-LINE "S" HOOK\ UNIVERSAL HOUSING KIT Figure 4-18. Detector Placement in Bracket 0 A Be sure mounting penetrations are liquid and grease tight. WARNING S P/N 220423 4-17 January 2007 Installation 4-4.1.4.2 Cabling Mechanical Detection - Both Lines If cabling Line 1 (knockout 3), turn ratchet wheel (counterclockwise) of detection beam until the cable through-hole is vertical (see Figure 4-19). S If cabling Line 2 (knockout 4/6), turn ratchet wheel of detection beam until the cable through- hole is horizontal. Note: When cabling detection line 2, use either Knockout 4 or Knockout 6. See Figure 4-19. Feed the end of the cable through the hole into the center of the ratchet wheel and pull the cable toward you. Leave approximately 6 inches (152 mm) of cable. Slip a Crimp Sleeve (P/N 214951) over the end of the cable. Making a loop, slip the end back through the Crimp Sleeve. Using Crimping Tool (P/N 253538) crimp the sleeve to the cable. THROUGH HOLE IN RATCHET SPOOL, DETECTION LINE 2 THROUGH HOLE IN RATCHET SPOOL, DETECTION LINE I DETECTION BEAMS IN RELEASED POSITION ACTUATION LATCH IN HORIZONTAL (SET) POSITION DETECTION BEAMS IN SET POSITION Figure 4-19. Cabling Mechanical Detection January 2007 448 P/N 220423 Installation Cut the loop off of the crimped cable assembly. Cut any loose ends off as close to the Crimp Sleeve as possible. Pull the ends of the crimped cable back through until the end of the cable seats inside the central chamber of the ratchet wheel. By hand, turn the wheel until the cable wraps around the spool of the ratchet. The cable line is now ready to be set. If the line is fully cabled, the detection line may be set. Note: If using Detection Line 2, Knockout 4, the cable must go around the pulley wheel before going into the cable port of the ratchet wheel. When tightening the cable around the spool, it is important that the cable be seated in the bottom of the groove on the pulley wheel. The cable may tend to wrap itself around other components in the XV Control System. Use caution in tightening the cable to ensure the proper path or a cable jam could occur resulting in the malfunction of the system. A CAUTION Use care when tightening the cable. Tighten cable until the detection arm makes contact with the beam stop. Do not overtighten. BEAM STOP FOR DETECTION LINE I DETECTION ARM BEAM STOP FOR DETECTION LINE 2 DETECTION ARM Figure 4-20. Close Up View of Detection Lines 1 and 2 Beam Stops P/N 220423 4-19 January 2007 S 2 I 3 3A 8 5 4 7 Installation 4-4.1.4.3 Cabling Detection Line 1 Only - Includes Lockout of Detection Line 2 Figure 4-21. XV with Detection Line 2 Locked Out Table 4-2. Cabling Detection Line 1 Only Item Description 1 Lockout screw pad (shown with one red lockout screw removed) 2 Actuation Latch 3 Spring and beam for Detection Line 2 (locked out) 3A Spring Post for Detection Line 2 (spring removed) 4 Spring and beam for Detection Line 1 (set with cable) 4A Spring Post for Detection Line 1 5 Beam Stop for Detection Line 1 6 Beam Stop for Detection Line 2 7 Lockout pad for Detection Line 1 (not used, line set) 8 Lockout pad for Detection Line 2 (red lockout screw inserted) Ensure that nothing is armed or set in the XV. With the XV completely disarmed, remove the spring from its respective post (item 3A, Detection Line 2). It is permissible to remove the spring from the detection beam. Push the detection beam (item 3) against its respective beam stop (item 6). Using a 9/64-inch allen key (hex) remove one of the red lockout screws from storage pad (item 1) and carefully thread into lockout pad (item 8). 0 January 2007 4-20 P/N 220423 Installation 4-4.1.4.4 Cabling Detection Line 2 Only (Option 1)— Includes Lockout of Detection Line 1 I 3 3A 8 5 4 7 PA Figure 4-22. XV with Detection Line 1 Locked Out Table 4-3. Cabling Detection Line 2 Only - Option 1 Item Description 1 Lockout screw pad (shown with one red lockout screw removed) 2 Actuation Latch 3 Spring and beam for Detection Line 2 (set with cable) 3A Spring Post for Detection Line 2 4 Spring and beam for Detection Line 1 (locked out) 4A Spring Post for Detection Line 1 (spring removed) 5 Beam Stop for Detection Line 1 6 Beam Stop for Detection Line 2 7 Lockout pad for Detection Line 1 (red lockout screw inserted) 8 Lockout pad for Detection Line 2 (not used, line set) Ensure that nothing is armed or set in the XV. With the XV completely disarmed, remove the spring from its respective post (item 4A, Detection Line 1). It is permissible to remove the spring from the detection beam. Push the detection beam (item 4) against its respective beam stop (item 5). Using a 9/64-inch allen key (hex) remove one of the red lockout screws from storage pad (item 1) and carefully thread into lockout pad (item 7). P/N 220423 4-21 January 2007 Installation 4-4.1.4.5 Cabling Detection Line 2 Only (Option 2)— Includes Lockout of Detection Line 1 3 3A 8 5 4 7 Figure 4-23. XV with Detection Line 1 Locked Out Table 4-4. Cabling Detection Line 2 Only - Option 2 Item Description 1 Lockout screw pad (shown with one red lockout screw removed) 2 Actuation Latch 3 Spring and beam for Detection Line 2 (set with cable) 3A Spring Post for Detection Line 2 4 Spring and beam for Detection Line 1 (locked out) 4A Spring Post for Detection Line 1 (spring removed) 5 Beam Stop for Detection Line 1 6 Beam Stop for Detection Line 2 7 Lockout pad for Detection Line 1 (red lockout screw inserted) 8 Lockout pad for Detection Line 2 (not used, line set) Ensure that nothing is armed or set in the XV. With the XV completely disarmed, remove the spring from its respective post (item 4A, Detection Line 1). It is permissible to remove the spring from the detection beam. Push the detection beam (item 4) against its respective beam stop (item 5). Using a 9/64-inch allen key (hex) remove one of the red lockout screws from storage pad (item 1) and carefully thread into lockout pad (item 7). lanuary 2007 4-22 P/N 220423 HIGH MOUNT MICROS WITCH S HI MICROSWITCH Installation 4-4.1.5 ATTACHING MICROSWITCHES, P/N 87-120039-001 4-4.1.5.1 High Mount Location for Microswitches The High Mounted Microswitch mounts with the paddle(s) facing up into the Cam/Flag. When in the 'Set' position, the Cam/Flag pushes down on the paddle(s) of the microswitch. When the Cam/Flag is released, the microswitch(es) release and change position (see Figure 4-27 for wiring diagram, and Figure 4-24 for mounting). The microswitches are best mounted when the system is in the 'Released' position. Two pairs of #4 screws are included with each microswitch kit: 5/8-inch long and 1-inch long x 3/32-inch Allen Key. If mounting a single switch, use the 5/8-inch screws. If mounting two switches, use the 1-inch long screws. After mounting the microswitch, turn the Cam/Flag to the 'Set' position to ensure the paddles move far enough down to change the phase of the microswitch. Use the included pigtail assembly to connect the microswitch to the circuit being monitored. See Figures 4-26, 4-27, 4-28, and 4-29 for wiring diagrams. Note: It is recommended that the pigtails be threaded into the port before attempting to plug it onto the microswitch contacts. All splices and connections should be made in a separate approved electrical box connected by EMT or other approved conduit. See NFPA 70 and NFPA 72 for proper wiring guidelines. RELEASED POSITION SET POSITION Figure 4-24. High Mount Microswitch, 'Released' and 'Set' Positions P/N 220423 4-23 January 2007 Installation 4-4.1.5.2 Deep Mount Location for Microswitches The Deep Mounted Microswitch mounts with the paddle(s) facing down, away from the Cam/Flag and trigger. When in the 'Set' position, the trigger pin pushes up on the paddle(s) of the microswitch. When the Cam/Flag is released, the microswitch(es) release and change position. See Figure 4-27 for wiring diagram. See Figure 4-25 for mounting information. The microswitches should be mounted when the system is in the 'Released' position. Two pairs of #4 screws are included with each microswitch kit: 5/8-inch long and 1-inch long x 3/32-inch Allen Key. If mounting a single microswitch, use the 5/8-inch screws. If mounting two microswitches, use the 1-inch long screws. After mounting the microswitch, turn the Cam/Flag to the 'Set' position to ensure the paddles move far enough down to change the position of the microswitch. Use the included pigtail assembly to connect the Microswitch to the circuit being monitored. See Figure 4-29 to see the terminal type microswitch positions when the XV Control System is in the Set and Released states. See Figures 4-26, 4-27, 4-28, and 4-29 for general wiring diagrams. See Figures Figure 4-31 and Figure 4-32 for initiating and releasing wiring diagrams. Note: It is recommended that the pigtails be threaded into the port before attempting to plug it onto the microswitch contacts. All splices and connections should be made in a separate electrical junction box connected by EMT or other approved conduit. See NFPA 70 and 72 for proper wiring guidelines. Mounting the microswitch with the pigtails attached and inserted into the outlet is recommended. When setting the Cam/Flag, make sure the trigger pin turns under the microswitch paddle(s) and pushes up to set the microswitch. If the trigger pin is "above" or between the paddle and the microswitch, the microswitch will not CAUTION change position upon actuation of the "Control System which could result in system malfunction. January 2007 4-24 P/N 220423 n RELEASED POSITION SET POSITION DEEP MOUNT MICROSWITCH S PIN ENGAGING MICROSWITCII PADDLE Installation Figure 4-25. Deep Mount Microswitch, 'Released' and 'Set' Positions P/N 220423 4-25 January 2007 Installation 4-4.1.6 WIRING MICROSWITCHES These are used when it is necessary to open or close electrical circuits. The following are examples, but not limited to: Electric appliance shutdown Make up air shutdown Electric gas valve shutdown Shuntbreaker/relay Note: Not for alarm initiation. ELECTRICAL MICROS ED T. BROWN .1 BROWNIWHFTE BLACK YELLOW YELLOW/WHITE BLUE BLUE/WHITE Figure 4-26. Microswitch Kit, P/N 87-120039-001, 87-120039-501 Table 4-5. Electrical Ratings for Microswitch Kit, P/N 87-120039-001 and 87-120039-501 125/250 Vac 20-1/2 Amps 250 Vac 1-1/2 HP 125 Vac 1/2 HP CLOSED RED LT. BROWN LT. BROWN/WHITE OPEN BLACK YELLOW YELLOW/WHITE MON WHITE BLUE BLUE/WHITE SWITCH POSITION WHEN XV CAM/FLAG IS IN 'RELEASED' POSITION Figure 4-27. Microswitch on Released Position January 2007 4-26 P/N 220423 Installation Microswitch to be used for: Alarm initiation • Solenoid release Not to be used for: Electric appliance shutdown Make up air shutdown Electric gas valve shutdown Shuntbreaker/relay 12 T4 Figure 4-28. Microswitch in Released Position, P/N 87-120047-001 Table 4-6. Electrical Ratings for Microswitch P/N 87-120047-001 250 Vac 15 Amps 250 Vac 1/2 HP 125 Vac 1/2 HP CLOSED T2 OPEN T4 COMMON TI SWITCH POSITION WHEN XV CAM/FLAG IS IN 'RELEASED' POSITION Figure 4-29. Microswitch (Terminal Type) Position in Released Position P/N 220423 4-27 January 2007 Installation 4-4.1.7 MOUNTING THE SOLENOID, P/N 83-100034-001 The Solenoid can be used in conjunction with mechanical detection or if mechanical detection or a Remote Manual Release is not needed. Red lockout screws are mounted in the control system. 0 The Solenoid includes an attached mounting bracket. Included in the hardware kit are two Allen screws. The Solenoid operates on 24 Vdc only. Connection to a higher voltage can result in non-operation, or burning out of the coil. A Work on the Solenoid should never take place while the system is in the 'Set' WARNING and ready position. The Solenoid operates directly on the latch. Ensure that the System Nitrogen Cartridge is removed and the Cam/Flag assembly is released or locked out with the Keeper Pin (P/N 60-9197108-000). Using a 3/32-inch Allen key, position the Solenoid behind the High-Pressure Nitrogen Tubing, aligning the mounting bracket with the mounting screw holes on the actuator mounting pad (see Figure 4-30). Secure the Solenoid and bracket assembly to the XV Control System enclosure with the enclosed 3/32-inch Allen screws. Dress the wires from the Solenoid up above the internal nitrogen hose, along the bottom of the XV and in front of the high mount microswitch mounting pad. Using a cable tie, secure the Solenoid wires to the internal nitrogen hose. Note: Wiring of the Solenoid must be done according to NFPA 72, National Fire Alarm Code and NFPA 70, National Electrical Code. Wiring the Solenoid through a Microswitch is required. The solenoid coil is 24 Vdc at 1.5 Amp and at 70°F (210C). 0 Wire the Solenoid to the microswitch: - Wire one lead from the Solenoid to terminal Ti of the microswitch. - Wire the second lead from the Solenoid through Knockout 1 or Knockout 2 through the conduit and into an approved control panel. - Finish the releasing loop by attaching a wire to T4 of the microswitch, through the conduit and into an approved control panel. See Figure 4-30. Releasing the XV Control System opens the contact and stops the releasing current. January 2007 4-28 P/N 220423 fl Installation Figure 4-30. Solenoid Mounted and Wired in the XV Control System Note: Dress the wires from the Solenoid down along in front of the high mount microswitch mounting pad and out through Knockout 1 or Knockout 2. Refer to Figure 4-31 and Figure 4-32 for initiation and releasing wiring diagrams. . P/N 220423 4-29 January 2007 Installation WIRE TYPE KEY ALARM WIRES TO EOL - - - - - - AND/OR OTHER DEVICES MICROSWITCH (INTERNAL) ALARM WIRES FROM CONTROL PANEL - /\ DETECTION \.•_y I LOOP TERMINALS CLOSED TERMINAL 2 ATTACH EOL TO TERMINAL 2 OF MICROSWITCH FLAG DISENGAGED BY XV ATTACH ONE ONE SIDE OF ALARM CIRCUIT AND EOL TO TERMINAL 4 OF MICROSWITCH OPEN TERMINAL 4 ATTACH ONE SIDE OF ALARM CIRCUIT TO TERMINAL I OF MICROS WITCH COMMON TERMINAL I SWITCH POSITION WHEN XV FLAG/CAM IS IN RELEASED POSITION Figure 4-31. Alarm Wiring with Terminal Type Microswitch WIRE TYPE KEY - ALARM WIRES TO XV - - - - -. -. SOLENOID AND/OR OTHER DEVICES MICROSWITCH (INTERNAL) ALARM WIRES FROM CONTROL PANEL XV SOLENOID PIN 81-100034.001 24 VDC ONLY ---\ 0' I' RELEASING CIRCUIT IN COMPATIBLE CONTROL PANEL (24 VOC ONLY) I SPLICE SOLENOID LEAD TO RELEASING CIRCUIT I - - 7 ATTACH SOLENOID LEAD TO TERMINAL I OF MICROSWITCH COMMON ATTACH RELEASING CIRCUIT TO TERMINAL 1 TERMINAL 4 OF MICROSWITCH CLOSED TERMINAL 4 OPEN TERMINAL 2 FLAG ENGAGED TERMINAL 2 NOT USED BY XV SWITCH POSITION WHEN XV FLAG/CAM IS IN SET POSITION Figure 4-32. Release Wiring with Terminal Type Microswitch January 2007 4-30 P/N 220423 Installation 4-4.1.7.1 Locking Out Detection Lines 1 and 2 E 3. 2 SOLENOID S Figure 4-33. Locking Out Detection Lines 1 and 2 with Solenoid Mounted in XV Table 4-7. Locking Out Detection Lines 1 and 2 Item Description 1 Lockout screw pad (shown with red lockout screws removed) 2 Actuation Latch 3 Spring and beam for Detection Line 2 (locked out) 3A Spring Post for Detection Line 2 (spring removed) 4 Spring and beam for Detection Line 1 (locked out) 4A Spring Post for Detection Line 1 (spring removed) 5 Beam Stop for Detection Line 1 6 Beam Stop for Detection Line 2 7 Lockout pad for Detection Line 1 (red lockout screw inserted) 8 Lockout pad for Detection Line 2 (red lockout screw inserted) P/N 220423 4-31 January 2007 Installation Ensure that nothing is armed or set in the XV. With the XV completely disarmed, remove the spring from its respective posts (item 3A, Detection Line 2, and item 4A, Detection Line 1). It is permissible to remove the spring from the detection beam. Push the detection beam (item 4) against its respective beam stop (item 5). Push the detection beam (item 3) against its respective beam stop (item 6). Using a 9/64-inch allen key (hex) remove red lockout screws from storage pad (item 1) and carefully thread into lockout pads (items 7 and 8). CAUTION Never lock out a detection line that is being used in a fire protection system. Refer to the appropriate DIOMs for instructions on disabling the system for CAUTION service, repair, and maintenance. January 2007 4-32 P/N 220423 Installation 4-4.2 Optional Equipment Installation [1 4-4.2.1 INSTALLING REMOTE MANUAL RELEASE, P/N 875572 The Remote Manual Release is equipped with a safety pin and seal wire which must be removed to permit installation of the control cable from the XV Control System. Note: The Remote Manual Release is optional if the XV Control System (local manual release) is in a clearly visible, easily accessible, unobstructed location. If it is not, a Remote Manual Release must be used for mechanical systems. Install the Remote Manual Release as outlined in Steps 1 through 9 (see Figure 4-34). Mount the Remote Manual Release at a means of egress, on a clear, unobstructed exit location between 42 - 48 inches (1067 - 1219 mm) above the floor. Refer to NFPA 17A and NFPA 96, latest editions.The cable can enter the handle from the side hole in the snap- out cover or from the rear of the handle. If the cable is to enter from the rear, perform alternate Steps 1-a and 1-b, otherwise, proceed to Step 2. a. Drill a hole in the wall opposite the position of the Remote Manual Release handle plug (when mounted). a. Attach a 1/2-inch EMT adapter to the hole in the wall. Mount the back plate to the wall using bolts or No. 10 self-tapping wood screws of required length. Remove the Corner Pulley covers to aid in installing the 1/16-inch steel cable through the system. Feed the 1/16-inch steel cable through the Remote Manual Release through 1/2-inch conduit or EMT to the XV Control System. Use Corner Pulleys (P/N 844648) for all changes in direction. Leave at least 12-inches of 1/16-inch steel cable coming out of the Remote Manual Release. Note: The Remote Manual Release cable attaches to the latch of the XV Control System. The Remote Manual Release uses Port 5 of the XV Control System. REMOTE MANUAL RELEASE (KNOCKOUT 5) REMOTE MANUAL RELEASE CABLE ACTUATION LATCH 1-114 in. (32 mm) CRIMP Figure 4-34. Remote Manual Release with Detection Lines 1 and 2 Locked Out 0 S. There is a through hole in the end of the actuation latch. Carefully feed the control cable through the hole in the actuation latch. P/N 220423 4-33 January 2007 Installation Note: It is important that the control cable slips easily through the hole in the end of the actuation latch. The actuation latch must be able to operate without interference from the control cable. Later, the movement of the actuation latch assembly will be tested before completing the setting of the XV Control System. Approximately 1-1/4 inches (32 mm) of control cable (with crimp end not included) should be left under the actuation latch, when in the 'Released' position. Slip a Crimp Sleeve (P/N 214951) over the end of the control cable. Making a loop, slip the end back through the Crimp Sleeve. Use the Crimping Tool (P/N 253538) to fasten the Crimp Sleeve to the control cable. Cut the loop off of the crimped cable assembly. Cut any loose ends off as close to the Crimp Sleeve as possible. If a second Remote Manual Release is required; use the Tee Pulley assembly (P/N 843791). January 2007 4-34 P/N 220423 Components 2-3.1.8.3 Thermo-Bulb Links, P/N 87-12009X-XXX UL Listed and FM Approved Thermo-Bulb Links, shown in Figure 2-22, are used in conjunction . with Universal-Link Housing Kits (P/N 87-120064-001) and/or Detector Housing Kits (P/N 804548). The links are held together with a liquid-filled glass tube (Thermo-Bulb), which bursts at a predetermined temperature, allowing the two halves of the link to separate. The types of Thermo-Bulb links are: Rapid Response Standard Response These Thermo-Bulb links are available in various temperature ratings with a minimum/maximum load rating of 0 lb./50 lb. (0 kg/23kg). THERMO-BU RMO-BULB > CI Figure 2-22. Thermo-Bulb Link, P/N 87-12009X-XXX P/N 220423 2-21 January 2007 LI Industrial Dry Chemical Kidde Fire Systems A UTC Fire & Security Company Cylinder and Valve Assembly Effective: March 2007 K-83-OO1 DESCRIPTION The cylinder and valve assembly is equipped with a plated forged brass valve, pressure gauge, fusible plug relief device, and a steel alloy cylinder shell. The cylinder conforms to DOT Specification 4BW-360. The assembly is pressurized with Nitrogen to 360 PSIG (24.8 bar gauge) at 70°F (21.1°C). The cylinder valve mates with a discharge adapter designed for use with Kidde® Pre- Engineered Fire Suppression Systems. The cylinder valve is also designed to accept any of the Pre-Engi- neered System control heads. "A" 1111 Overall Charge or Fill Nominal Dia. Assembly Wall Cylinder! Type of (in) Mounting Part Number Weight of Height (in.) Valve Model Powder Bracket Part Powder (lb.) Number A B IND-21 486573 ABC 21 9 17.6 486487 IND-25 486570 BC 25 9 17.6 486487 lND-45 486574 ABC 45 9 30.8 486488 IND-50 486571 BC 50 9 30.8 486488 IND-70 83-100018-001 ABC 68 12.3 30.2 87-100009-001 IND-75 83-100019-001 BC 75 12.3 30.2 87-100009-001 This literature is provided for informational purposes only. KIDDE-FENWAL, INC. assumes i Kidde Fire Systems no responsibility for the product's suitability for a particular application. The product must be A UTC Fire & Security Company properly applied to work correctly. I 400 Main Street If you need more information on this product, or if you have a particular problem or question, I Ashland, MA 01721 contact KIDDE-FENWAL, INC., Ashland, MA 01721. Telephone: (508) 881-2000. Ph: 508.881.2000 K-83-001 Rev AB © 2007 Kidde-Fenwal Inc. Printed in USA Fax: 508.881.8920 www.Wddefiresystems.com Industrial Dry Chemical Kidde Fire Systems A UTC Fire & Security Company . Mounting Bracket Kits Effective: March 2007 K-83-002 3/8" FASTENING .406 DIA. TRU HARDWARE (TO (3) WTC HOLES FLEXI8 WALL) (TYP) STRAP DESCRIPTION A mounting bracket kit is used for mounting all cylinder and valve assemblies. The kit consists of a steel bracket with a shelf to hold the cylinder bottom. A cylinder strap is used to secure the cylinder to the bracket. Prior to instal- lation, ensure that the wall or other mounting surface will support the recommended load specified in the table. Mount the bracket to the surface using three (3) 3/8-in. bolts or screws. Mounting Recommended Cylinder/Valve Dimension Dimension Dimension Dimension Bracket Part Wall-Support Model A B (in.) C (in.) D (in.) Number Load 486487 lND-21 13.12 in. 11.50 in. 9.75 in. 8.12 in. 65 lb. lND-25 486488 lND-45 19.62 in. 18.00 in. 9.75 in. 8.12 in. 130 lb. lND-50 87-100009-001 lND-70 21.00 in. 18.80 in. 13.25 in. 12.50 in. 225 lb. lND-75 fl S This literature is provided for informational purposes only. KIDDE-FENWAL, INC. assumes no responsibility for the product's suitability for a particular application. The product must be properly applied to work correctly. If you need more information on this product, or if you have a particular problem or question, contact KIDDE-FENWAL, INC., Ashland, MA 01721. Telephone: (508) 881-2000. K-83-002 Rev AB © 2007 Kidde-Fenwal Inc. Printed in USA Kidde Fire Systems A UTC Fire & Security Company 400 Main Street Ashland, MA 01721 Ph: 508.881.2000 Fax: 508.881.8920 www.l<iddefiresystems.com 3f4 NPT FLANGE PLATE 0-RING ADAPTER Industrial Dry Chemical Kidde Fire Systems A UTC Fire & Security Company Discharge Adapter Kits Effective: March 2007 go K-83-003 P/N: 844908 DESCRIPTION The discharge adapter provides a means to connect 3/4- inch discharge pipe (or 1-inch pipe with a concentric reducer or reducing bushing) to any Industrial Dry Chem- ical cylinder and valve assembly. The discharge-adapter kit consists of a male, 3/4-inch NPT, brass, discharge-valve-outlet adapter and a steel flange plate for securing the discharge adapter to the valve outlet. This literature is provided for informational purposes only. KIDDE-FENWAL, INC. assumes i Kidde Fire Systems no responsibility for the product's suitability for a particular application. The product must be I A UTC Fire & Security Company properly applied to work correctly. I 400 Main Street If you need more information on this product, or if you have a particular problem or question, I Ashland, MA 01721 contact KIDDE-FENWAL, INC., Ashland, MA 01721. Telephone: (508)881-2000. I Ph: 508.881.2000 K-83-003 Rev AB © 2007 Kidde-Fenwal Inc. Printed in USA Fax: 508.881.8920 www.kddefir,esystems.com Industrial Dry Chemical /Kidde Fire Systems Total-Flooding Nozzle Security Company March 2011 P/N: 83-100005-001 DESCRIPTION The Total-Flooding (TF) Nozzle is designed to uniformly discharge Kidde® dry chemical suppression agent throughout an enclosed volume. This nozzle is to be mounted at ceiling level (unless otherwise listed) with the orifice tip pointed vertically down. The TF Nozzle is also used to protect the work area volume for open face spray booth applications and for vehicle spray booth applica- tions. Each TF Nozzle is factory-equipped with a blow-off cap to protect the nozzle orifices and to prevent moisture buildup in the discharge piping. BLOW-OFF CAP This literature is provided for informational purposes only. KIDDE-FENWAL, INC. assumes no responsibility for the product's suitability for a particular application. The product must be properly applied to work correctly. If you need more information on this product, or if you have a particular problem or question, contact KIDDE-FENWAL, INC., Ashland, MA 01721. Telephone: (508) 881-2000. K-83-012 Rev AC © 2011 Kidde-Fenwal Inc. Printed in USA Kidde Fire Systems A UTC Fire & Security company 400 Main Street Ashland, MA 01721 Ph: 508.881.2000 Fax: 508.881.8920 www.kddefiresystems.com Industrial Dry Chemical Kidde Fire Systems Fusible Link Housing Kit with Fusible Link A UTC Fire & Security Company Effective: March 2007 K-83-014 P/N: 804548 DESCRIPTION UL Listed and FM Approved Fusible Links are used in conjunction with the Fusible Link Housing Kit. The Fus- ible Links are held together with a low melting alloy, which melts at a predetermined temperature, allowing the two halves of the link to separate. Fusible Links are available in various temperature ratings as shown in table. There are two temperature designations which apply to both fusible links and quartizoid bulb links. One tempera- ture is called the rating temperature, and the other is called the maximum exposure temperature. 1/2" EMT 1/2" EMT CONNECTOR LOCKNUT LOCKNUT CONNECTOR —Vil, )~~114-3- "S° HOOKS (Not MIN. _j /N -LNO Supplied) _ 1/16" CABLE TO /1/16" CABLE TO ML LINK' ABLE CONNECTOR CONTROL ANOTHER DETECN ACTUATING DEVICE CRIMP TYPE CRIMP TYPE OR REMOTE MANUAL CABLE CONNECTOR Fusible Link Rating Maximum Exposure Temperature Part Number Load Rating ____________ Minimum Maximum 165°F (74°C) 100°F (38°C) 282661 10 lb. 40 lb. 212°F (100°C) 150°F (65°C) 282662 10 lb. 40 lb. 306°F (182°C) 300°F (149°C) 282664 10 lb. 40 lb. 500°F (260°C) 440°F (226°C) 282666 10 lb. 40 lb. This literature is provided for informational purposes only. KIDDE-FENWAL, INC. assumes no responsibility for the product's suitability for a particular application. The product must be properly applied to work correctly. If you need more information on this product, or if you have a particular problem or question, contact KIDDE-FENWAL, INC., Ashland, MA 01721. Telephone: (508) 881-2000. K-83-014 Rev AB © 2007 Kidde-Fenwal Inc. Printed in USA Kidde Fire Systems A UTC Fire & Security Company 400 Main Street Ashland, MA 01721 Ph: 508.881.2000 Fax: 508.881.8920 www.;dddefiresystems.com F_ Industrial Dry Chemical n~A~ idd !Security Fire Systems TC Fire Company Mechanical, Remote Manual Release Effective: March 2007 K-83-021 P/N: 875572 DESCRIPTION The Mechanical, Remote Manual Release is provided as a means of manually actuating the system from a remote location. The Mechanical, Remote Manual Release is attached to the primary control head with 1/16-inch cable. To actuate the system through the Mechanical, Remote Manual Release, pull out the ring pin and pull hard on the handle. Each manual release is supplied with a separate name- plate. This nameplate must be attached to the mounting surface 1 inch above or below the pull station. An additional Mechanical, Remote Manual Release may be installed with a Kidde® Tee Pulley (P/N 843791). S Ll This literature is provided for informational purposes only. KIDDE-FENWAL, INC. assumes no responsibility for the product's suitability for a particular application. The product must be properly applied to work correctly. If you need more information on this product, or if you have a particular problem or question, contact KIDDE-FENWAL, INC., Ashland, MA 01721. Telephone: (508) 881-2000. K-83-021 Rev AB © 2007 Kidde-Fenwal Inc. Printed in USA Kidde Fire Systems A UTC Fire & Security Company 400 Main Street Ashland, MA 01721 Ph: 508.881.2000 Fax: 508.881.8920 www.kddefiresystems.com Industrial Dry Chemical Kidde Fire Systems Corner Pulley A UTC Fire & Security Company Effective: March 2007 K-83-025 P/N 844648 DESCRIPTION The Corner Pulley is used to change the direction of the system cable runs. The cable's protective conduit (1/2- inch EMT) is attached to the corner pulley with the pro- vided coupling nuts. The Corner Pulley is equipped with a ball-bearing pulley for minimum resistance to the cable travel. COVER SCREW COUPLING NUTS 0.62" (16mm) S 2- 1 E.M.T. CONNECTIONS COMPRESSION TYPE 2.75" (70mm) APPROX. This literature is provided for informational purposes only. KIDDE-FENWAL, INC. assumes i Kidde Fire Systems no responsibility for the product's suitability for a particular application. The product must be I A UTC Fire & Security company properly applied to work correctly. I 400 Main Street If you need more information on this product, or if you have a particular problem or question, I Ashland, MA 01721 contact KIDDE-FENWAL, INC., Ashland, MA 01721. Telephone: (508) 681-2000. Ph flR 881 2000 K-83-025 Rev AB © 2007 Kidde-Fenwal Inc. Printed in USA Fax: 508.881.8920 www.kiddefiresystems. corn