HomeMy WebLinkAbout2020 CASSIA RD; 102; AS080020; Permit11/3/2020 AS080020 Permit Data
City of Carlsbad
Sprinkler Permit
Permit No: AS080020
Job Address: 2020 CASSIA RD Status: ISSUED
Permit Type: SPRINK Applied 2/13/2008
Parcel No: 2150210200 Approved: 2/26/2008
Lot #: 0
Reference No.: Issued: 2/26/2008
PC #: Inspector:
Project Title DR. HULSE TI FIRE SPRINKLER PLAN CHECK & INSPECTIONS
Applicant:
PARAMOUNT FIRE SYSTEMS, INC
P.O. BOX 713194
SANTEE, CA
619-562-6247
Owner:
FRANZ FAMILY REVOCABLE TRUST 06-26-
96
P0 BOX 2711
RANCHO SANTA FE CA
Fees ($) Add'l Fees ($) Total ($) Balance ($)
130 0 130 0.
1/1
A&58062-0
tqca /Fire & Building
/ Products
Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500
Series TY-B - 2.8, 5.6, and 8.0 K-factor
Upright, Pendent, and Recessed Pendent Sprinklers
Standard Response, Standard Coverage
General
Description
The Series TV-B, 2.8, 5.6, and 8.0
K-factor, Upright and Pendent Sprin-
klers described in this data sheet are
standard response - standard cover-
age, decorative 5 mm glass bulb type
spray sprinklers designed for use in
light, ordinary, or extra hazard, com-
mercial occupancies such as banks,
hotels, shopping malls, factories, refin-
eries, chemical plants, etc.
The recessed version of the Series
TV-B Pendent Sprinkler, where appli-
cable, is intended for use in areas with
a finished ceiling. It uses a two-piece
Style 10(1/2 inch NPT) or Style 40 (3/4
inch NPT) Recessed Escutcheon. The
Recessed Escutcheon provides 1/2
inch (12,7 mm) of recessed adjust-
ment or up to 3/4 inch (19,1 mm) of
total adjustment from the flush pen-
dent position. The adjustment pro-
vided by the Recessed Escutcheon re-
duces the accuracy to which the fixed
pipe drops to the sprinklers must be
cut.
Corrosion resistant coatings, where
applicable, are utilized to extend the
life of copper alloy sprinklers beyond
that which would otherwise be ob-
tained when exposed to corrosive at-
mospheres. Although corrosion resis-
tant coated sprinklers have passed the
standard corrosion tests of the appli-
IMPORTANT
Always refer to Technical Data
Sheet TFP 700 for the "INSTALLER
WARNING" that provides cautions
with respect to handling and instal-
lation of sprinkler systems and com-
ponents. Improper handling and in-
stallation can permanently damage
a sprinkler system or its compo-
nents and cause the sprinkler to fail
to operate in a fire situation or cause
it to operate prematurely.
cable approval agencies, the testing is
not representative of all possible cor-
rosive atmospheres. Consequently, it
is recommended that the end user be
consulted with respect to the suitability
of these coatings for any given corro-
sive environment. The effects of ambi-
ent temperature, concentration of
chemicals, and gas/chemical velocity,
should be considered, as a minimum,
along with the corrosive nature of the
chemical to which the sprinklers will be
exposed.
An intermediate level version of the
Series TV-B Pendent Sprinkler can be
obtained by utilizing the Series TV-B
Pendent Sprinkler in combination with
the Model S2 Shield.
WARNINGS
The Series TY-B Sprinklers described
herein must be installed and main-
tained in compliance with this docu-
ment, as well as with the applicable
standards of the National Fire Protec-
tion Association, in addition to the
standards of any other authorities hav-
ing jurisdiction. Failure to do so may
impair the performance of these de-
vices.
The owner is responsible for maintain-
ing their fire protection system and de-
vices in proper operating condition.
The installing contractor or sprinkler
manufacturer should be contacted
with any questions.
Model/Sprinkler
Identification
Numbers
TYII5I - Upright 2.8K, 1/2"NPT
TY1251 - Pendent 2.8K, 1/2"NPT
TY3151 - Upright 5.61K, 1/2"NPT
TY3251 - Pendent 5.6K, 1/2"NPT
TY4151 - Upright 8.0K, 3/4"NPT
TY4251 - Pendent 8.0K, 3/4"NPT
TY4851 - Upright 8.0K, 1/2"NPT
TY4951 - Pendent 8.0K, 1/2"NPT
Page 1 of 8 MARCH, 2007 TFPI5I
ESCUTCHEON 7/16 (11,1 mm)
PLATE SEATING ** NOMINAL ,,
SURFACE 112 MAKE-IN NPT
2-1/4 \
(57,2 mm)
1-9/16" WRENCH
(39,7 mm) FLATS
55p*
DEFLECTOR
PENDENT UPRIGHT
CROSS
SECTION
SSU *
DEFLECTOR
2-3/16"
(55,6 mm) 4
t1
Page 2 of B TFPI5I
1 - Frame 3- Sealing 4- Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to
2 - Button Assembly 5 - Compression 7 - Bushing orifice seat on frame. Screw **Pipe thread connections per ISO 7/1 can be provided on
special request.
FIGURE 1
STANDARD RESPONSE SERIES TY-B UPRIGHT (TYII5I) AND PENDENT (TY1251) SPRINKLERS
2.8 K-FACTOR, 1/2 INCH NPT
STYLE 10
RECESSED *
ESCUTCHEON SSU
DEFLECTOR
[NOMINAL
11,1 mm) I
7/16"
I [I.zJ E-IN
(55,6 mm)
::i
MAK 2-3/16"
WRENCH
1/2" NPT** I
ESCUTCHEON
PLATE SEATING
SURFACE
23t16"_
(55,6 mm)
1-1/2"
(38,1 mm)
7/16" (11,1 mm)
** NOMINAL
NPT MAKE-IN
SSP DEFLECTOR* 2-7/8" (73,0 mm) DIA.
PENDENT RECESSED PENDENT UPRIGHT CROSS SECTION
1 - Frame 3- Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to 2 - Button Assembly 5 - Compression orifice seat on frame. Screw **Pipe thread connections per ISO 7/1 can be provided on
special request.
FIGURE 2
STANDARD RESPONSE SERIES TY-B UPRIGHT (TY3 151) AND PENDENT (TY3251) SPRINKLERS
5.6 K-FACTOR, 1/2 INCH NPT
0
TFPI5I Page 3 of 8
ESCUTCHEON 1/2" (12,7 mm) STYLE 40
PLATE SEATING ** NOMINAL RECESSED ssu" SURFACE 3/4"MAKE-IN ESCUTCHEON NPT DEFLECTOR
6*
4S FLATS
(12,7 mm)2-5/16"
NOIN
1/2"
(39,7mm)
HIMAKE-IN2-1/4"1-9/16
(58,7 mm)
RENC
57,2 mm)3
2-7/8" (73,0 mm) DIA. --] 3/4" NPT** SSP DEFLECTOR*
PENDENT RECESSED PENDENT UPRIGHT CROSS SECTION
1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to 2 - Button Assembly 5 - Compression orifice seat on frame. Screw **Pipe thread connections per ISO 7/1 can be provided on
special request.
FIGURE 3
STANDARD RESPONSE SERIES TY-B UPRIGHT (TY4 151) AND PENDENT (TY4251) SPRINKLERS
8.0 K-FACTOR, 3/4 INCH NPT
7/16" (11,1 mm)
1/2" ** NOMINAL SSU*
MAKE-IN DEFLECTOR NPT i I
* _ 6
I 5
2-3/16"
(55,6 mm) 4
-. SSP*
DEFLECTOR
PENDENT UPRIGHT
1 - Frame 3 - Sealing 4 - Bulb 6-Deflector * Temperature rating is indicated on deflector or adjacent to 2- Button Assembly 5 - Compression orifice seat on frame. Screw **Pipe thread connections per ISO 7/1 can be provided on
special request.
FIGURE 4
STANDARD RESPONSE SERIES TY-B UPRIGHT (TY4851) AND PENDENT (TY4951) SPRINKLERS
8.0 K-FACTOR, 1/2 INCH NPT
0
ESCUTCHEON
PLATE SEATING
SURFACE
2-1/4"
(57,2 mm)
1-9/16"
(39,7 mm)
WRENCH
FLATS
CROSS
SECTION
Page 4 of 8 TFPI5I
SPRINKLER FINISH (See Note 8)
K TYPE TEMP. BULB
LIQUID
NATURAL
BRASS
I CHROME
PLATED
WHITE
~POLYESTER
LEAD I
COATED COATED
WAX WAX OVER
LEAD OVER
2.8
1/2
NPT
PENDENT
(TY1251)
and
UPRIGHT
(TYII5I)
135F/57C Orange
12,3 N/A
155F/68°C Red
175°F/79C Yellow
200°F/93°C Green
286°F/141C Blue
360F/182°C Mauve 1,2
5.6
1/2
NPT
PENDENT
(TY3251)
and
UPRIGHT
(TY3151)
135°F/57*C Orange
1,23,4,5,6,7 1,2,3,5 1,2,3,5 1,2,3,5
155F/68°C Red
175°F/79C Yellow
200°F193°C Green
286°F/141C Blue 1,2, 3** 5** 1, 2**, 3** 5**
360F/182°C Mauve N/A
135°F/57°C Orange
1, 2, 3,4, 5
I I
1,2,4, 5
I
N/A
1,2
RECESSED
PENDENT
(1Y3251)*
Figure 4
155°F/68°C Red
175°F/79°C Yellow
200°F/93°C Green
286F/141°C Blue
8.0 3/40
NPT
PENDENT
(TY4251)
and
UPRIGHT
(TY4151)
135°F/57C Orange
1,2,3,4,5,6,7
1,2,5 1,2,3,5 1,2,5
155°F/68°C Red
175°F/79°C Yellow
200°F/93°C Green
286°F/141 °C Blue 1**,2**, 3** 5** 1.. 2"", 5**
360°F/182°C Mauve N/A
135°F/57"C Orange
1, 2, 3,4, 5 N/A
RECESSED
PENDENT
(1Y4251)*
Figure 5
155°F/68°C Red
175°F/79°C Yellow
200"F/93°C Green
286"F/141"C Blue 1,2
8.0
1/2"
NPT
PENDENT
(TY4951)
and
UPRIGHT
(TY4851)
135"F/57°C Orange
1,2, 3,4, 5,6 N/A
155°F/68"C Red
175°F/79"C Yellow
200"F/93"C Green
286"F/141"C Blue
360°F/182"C Mauve
NOTES:
Listed by Underwriters Laboratories, Inc. (UL).
Listed by Underwriters Laboratories, Inc. for use in Canada (C-UL).
Approved by Factory Mutual Research Corporation (FM).
Approved by the Loss Prevention Certification Board (LPCB Ref. No. 007k/03).
Approved by the City of New York under MEA 354-01-E.
VdS Approved (For details contact Tyco Fire & Building Products, Enschede, Netherlands, Tel. 31-53-428-4444/Fax 31-53-428-3377).
Approved by the Loss Prevention Certification Board (LPCB Ref. No. 094a/05).
Where Polyester Coated, Lead Coated, Wax Coated, and Wax over Lead Coated Sprinklers are noted to be UL and C-UL Listed, the
sprinklers are UL and C-UL Listed as Corrosion Resistant Sprinklers. Where Lead Coated, Wax Coated, and Wax over Lead Coated
is
Sprinklers are noted to be FM Approved, the sprinklers are FM Approved as Corrosion Resistant Sprinklers.
* Installed with Style 10 (1/2" NPT) or Style 40 (3/40 NPT) 3/4" Total Adjustment Recessed Escutcheon, as applicable.
150"F/66"C Maximum Ceiling Temperature.
TABLE A, LABORATORY LISTINGS AND APPROVALS
S
TFPI5I Page 5 of 8
SPRINKLER FINISH
K TYPE NATURAL CHROME WHITE LEAD WAX WAX OVER
BRASS PLATED POLYESTER COATED COATED LEAD COATED
2 PENDENT (TY1251)
1/2 and 175 PSI (12,1 BAR) N/A
NPT UPRIGHT (TY1I5I)
PENDENT (TY3251)
5.6 and 250 PSI (17,2 BAR) 175 PSI (12,1 BAR)
1/2' UPRIGHT (TY3151) OR
NPT 175 PSI (12,1 BAR) RECESSED PENDENT
(TY3251) (SEE NOTE 1) N/A
8.0 PENDENT (TY4251)
3/4" and 175 PSI (12,1 BAR)
NPT UPRIGHT (TY4151)
RECESSED PENDENT
(TY4251) 175 PSI (12,1 BAR) N/A
80 PENDENT (TY4951)
1/2" and 17S PSI (12,1 BAR)
NPT UPRIGHT (TY4851)
NOTE:
1. The maximum working pressure of 250 psi (17,2 bar) only applies to the Listing by Underwriters Laboratories, Inc. (UL); the Listing by
Underwriters Laboratories, Inc. for use in Canada (C-UL); and, the Approval by the City of New York.
TABLE B, MAXIMUM WORKING PRESSURE
Technical
Data
Approvals
UL and C-UL Listed.
FM, LPCB, VdS, and NYC Approved.
(Refer to Table A for complete ap-
proval information including corrosion
resistant status.)
Maximum Working Pressure
Refer to Table B.
Discharge Coefficient
K = 2.8 GPM/psi1l2 (40,3 LPM/bar1/2)
K = 5.6 GPM/p5i1/2 (80,6 LPM/bar112)
K = 8.0 GPM/ps1112 (115,2 LPM/bar112)
Temperature Ratings
Refer to Table A.
Finishes
Sprinkler: Refer to Table A.
Recessed Escutcheon: White Coated,
Chrome Plated, or Brass Plated.
Physical Characteristics
Frame .............Bronze
Button .........Brass/Copper
Sealing Assembly ..........
Beryllium Nickel w/Teflont
Bulb ...............Glass
Compression Screw .....Bronze
Deflector ...........Copper
Bushing (K=2.8) .......Bronze
Operation
The glass Bulb contains a fluid which
expands when exposed to heat. When
the rated temperature is reached, the
fluid expands sufficiently to shatter the
glass Bulb, allowing the sprinkler to
activate and water to flow.
Design
Criteria
The Series TY-B Pendent and Upright
Sprinklers are intended for fire protec-
tion systems designed in accordance
with the standard installation rules rec-
ognized by the applicable Listing or
Approval agency (e.g., UL Listing is
based on the requirements of NFPA
13, and FM Approval is based on the
requirements of FM's Loss Prevention
Data Sheets). Only the Style 10 or 40
Recessed Escutcheon, as applicable,
is to be used for recessed pendent
installations.
S
Page 6 of 8
TFPISI
5/8±1/4"
(15,9±6,4 mm)
FACE OF
SPRINKLER
FITTING
2-7/8" DIA.
(73,0 mm) 3/4" (19,1 mm)
1 I 2-1/4" DIA. /4"(6,4mm)
(57,2 mm) MOUNTING
- fli ArC
WRENCH RECESS
(END "A" USED FOR
1/2" NPT MODELS)
S
S
FIGURE 5
SERIES TY-B RECESSED PENDENT SPRINKLER ASSEMBLY
WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT
STYLE 10 RECESSED ESCUTCHEON
5.6 K-FACTOR, 1/2 INCH NPT
2-7/8" DIA. U..'
5/8±1/4" (73,0 mm) 3/4" (19,1 mm)
(15,916,4 mm) - 2-1/4" DIA. I 1/4" (6,4 mm)
FACE OF
(57,2 mm) MOUNTING
1/8"
SPRINKLER I PLATE
FITTING
(3,2 mm)
\4
MOUNTING
/7
SURFACE///
CLOSURE SERIES 1-5/16" (33,3 mm)I
TV-B 13/16" (20,6 mm)
FIGURE 6
SERIES TY-B RECESSED PENDENT SPRINKLER ASSEMBLY
WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT
STYLE 40 RECESSED ESCUTCHEON
8.0 K-FACTOR, 3/4 INCH NPT
WRENCH
RECESS
PUSH WRENCH
IN TO ENSURE
ENGAGEMENT
WITH SPRINKLER
WRENCHING AREA
FIGURE 8
W-TYPE 7 RECESSED
SPRINKLER WRENCH
Installation
The Series TV-B Sprinklers must be
installed in accordance with the follow-
ing instructions:
NOTES
Do not install any bulb type sprinkler if
the bulb is cracked or there is a loss of
liquid from the bulb. With the sprinkler
held horizontally, a small air bubble
should be present. The diameter of the
air bubble is approximately 1/16 inch
(1,6 mm) for the 135°F/57"C to 3/32
inch (2,4 mm) for the 360"F/182°C
temperature ratings.
A leak tight 1/2 inch NPT sprinkler joint
should be obtained with a torque of 7
to 14 ft.lbs. (9,5 to 19,0 Nm). A maxi-
mum of 21 ft. lbs. (28,5 Nm) of torque
may be used to install sprinklers with
1/2 NPT connections. A leak tight 3/4
inch NPT sprinkler joint should be ob-
tained with a torque of 10 to 20 ft.Ibs.
(13,4 to 26,8 Nm). A maximum of 30
ft.lbs. (40,7 Nm) of torque is to be used
to install sprinklers with 3/4 NPT con-
nections. Higher levels of torque may
distort the sprinkler inlet and cause
MOUNTING
SURFACE
CLOSURE SERIES
1/8"
(3,2 mm)
if
1-1/4" (31,8 mm)
3/4"(19,1 mm)
WRENCH RECESS
(END "B" USED FOR
3/4" NPT MODELS)
FIGURE 7
W-TYPE 6 SPRINKLER
WRENCH
TFPI5I Page 70f8
S
heated rod, in order to prevent the by brushing it with a soft bristle brush.
installer from being burned.1~mrp m" et ho ovart-icind tr, ,,r,irI dm
S
leakage or impairment of the sprinkler.
Do not attempt to make-up for insuffi-
cient adjustment in the escutcheon
plate by under- or over-tightening the
sprinkler. Readjust the position of the
sprinkler fitting to suit.
The Series TV-B Pendent and Up-
right Sprinklers must be installed in
accordance with the following instruc-
tions.
Step 1. Pendent sprinklers are to be
installed in the pendent position, and
upright sprinklers are to be installed in
the upright position.
Step 2. With pipe thread sealant ap-
plied to the pipe threads, hand tighten
the sprinkler into the sprinkler fitting.
Step 3. Tighten the sprinkler into the
sprinkler fitting using only the W-Type
6 Sprinkler Wrench (Ref. Figure 7),
except that an 8 or 10 inch adjustable
Crescent wrench is to be used for wax
coated sprinklers. With reference to
Figures 1, 2, 3, and 4 the W-Type 7
Sprinkler Wrench or the adjustable
Crescent wrench, as applicable is to
be applied to the wrench flats.
When installing wax coated sprinklers
with the adjustable Crescent wrench,
additional care needs to be exercised
to prevent damage to the wax coating
on the sprinkler wrench flats or frame
arms and, consequently, exposure of
bare metal to the corrosive environ-
ment. The jaws of the wrench should
be opened sufficiently wide to pass
over the wrench flats without damag-
ing the wax coating. Before wrench
tightening the sprinkler, the jaws of the
wrench are to be adjusted to just con-
tact the sprinkler wrench flats. After
wrench tightening the sprinkler, loosen
the wrench jaws before removing the
wrench.
After installation, the sprinkler wrench
flats and frame arms must be in-
spected and the wax coating re-
touched (repaired) whenever the coat-
ing has been damaged and bare metal
is exposed. The wax coating on the
wrench flats can be retouched by gen-
tly applying a heated 1/8 inch diameter
steel rod to the areas of wax that have
been damaged, to smooth it back over
areas where bare metal is exposed.
NOTES
Only retouching of the wax coating ap-
plied to the wrench flats and frame
arms is permitted, and the retouching
is to be performed only at the time of
the initial sprinkler installation.
The steel rod should be heated only to
the point at which it can begin to melt
the wax, and appropriate precautions
need to be taken, when handling the
The Series TV-B Recessed Pendent
Sprinklers must be installed in ac-
cordance with the following instruc-
tions.
Step A. After installing the Style 10 or
40 Mounting Plate, as applicable, over
the sprinkler threads and with pipe
thread sealant applied to the pipe
threads, hand tighten the sprinkler into
the sprinkler fitting.
Step B. Tighten the sprinkler into the
sprinkler fitting using only the W-Type
7 Recessed Sprinkler Wrench (Ref.
Figure 8). With reference to Figure 3
or 4, the W-Type 7 Recessed Sprinkler
Wrench is to be applied to the sprinkler
wrench flats.
Step C. After the ceiling has been in-
stalled or the finish coat has been ap-
plied, slide on the Style 10 or 40 Clo-
sure over the Series TY-B Sprinkler
and push the Closure over the Mount-
ing Plate until its flange comes in con-
tact with the ceiling.
Care and
Maintenance
The Series TV-B Sprinklers must be
maintained and serviced in accord-
ance with the following instructions:
NOTES
Before closing a fire protection system
main control valve for maintenance
work on the fire protection system that
it controls, permission to shut down the
affected fire protection system must be
obtained from the proper authorities
and all personnel who maybe affected
by this action must be notified.
The owner must assure that the sprin-
klers are not used for hanging of any
objects; otherwise, non-operation in
the event of a fire or inadvertent opera-
tion may result.
Absence of an escutcheon, which is
used to cover a clearance hole, may
delay the time to sprinkler operation in
a fire situation.
Sprinklers that are found to be leaking
or exhibiting visible signs of corrosion
must be replaced.
Automatic sprinklers must never be
painted, plated, coated or otherwise
altered after leaving the factory. Modi-
fied sprinklers must be replaced.
Sprinklers that have been exposed to
corrosive products of combustion, but
have not operated, should be replaced
if they cannot be completely cleaned
by wiping the sprinkler with a cloth or
age to the sprinklers - before, during,
and after installation. Sprinklers dam-
aged by dropping, striking, wrench
twist/slippage, or the like, must be re-
placed. Also, replace any sprinkler
that has a cracked bulb or that has lost
liquid from its bulb. (Ref. Installation
Section).
Frequent visual inspections are rec-
ommended to be initially performed for
corrosion resistant coated sprinklers,
after the installation has been com-
pleted, to verify the integrity of the cor-
rosion resistant coating. Thereafter,
annual inspections per NFPA 25
should suffice; however, instead of in-
specting from the floor level, a random
sampling of close-up visual inspec-
tions should be made, so as to better
determine the exact sprinkler condi-
tion and the long term integrity of the
corrosion resistant coating, as it may
be affected by the corrosive conditions
present.
The owner is responsible for the in-
spection, testing, and maintenance of
their fire protection system and de-
vices in compliance with this docu-
ment, as well as with the applicable
standards of the National Fire Protec-
tion Association (e.g., NFPA 25), in
addition to the standards of any other
authorities having jurisdiction. The in-
stalling contractor or sprinkler manu-
facturer should be contacted relative
to any questions.
It is recommended that automatic
sprinkler systems be inspected,
tested, and maintained by a qualified
Inspection Service in accordance with
local requirements and/or national
codes.
Page 80f8 TFPISI
S
PIN 57-XXX-X-XXX
L.. MODEUSIN_
530 2.8K UPRIGHT (1/2"NPT) TY1151
531 2.8K PENDENT (1/2"NPT) TY1251
570 5.6K UPRIGHT (1/2"NPT) TY3151
571 5.6K PENDENT (1/2"NPT) TY3251
590 8.0K UPRIGHT (314°NPT) TY4151
591 8.01K PENDENT (3/4"NPT) TY4251
560 8.0K UPRIGHT (1/2"NPT) TY4851
561 8.0K PENDENT (1/2"NPT) TY4951
SPRINKLER TEMPERATUR
j_ RATING
135 135°F/57C
155 155°F/68C
175 175*F/79*C
200 2000F/93*C
286 286*F/141*C
360 360*F/182*C
1 NATURAL BRASS
4 WHITE POLYESTER
3 WHITE (RAL9010) *
9 CHROME PLATED
7 LEAD COATED
6 WAX COATED 286*F/141*C MAX.
8 WAX OVER LEAD
286°F1141°C MAX.
TABLE C
PART NUMBER SELECTION
SERIES TY-B PENDENT AND UPRIGHT SPRINKLERS
S
Limited
Warranty
Products manufactured by Tyco Fire &
Building Products (TFBP) are war-
ranted solely to the original Buyer for
ten (10) years against defects in mate-
rial and workmanship when paid for
and properly installed and maintained
under normal use and service. This
warranty will expire ten (10) years
from date of shipment by TFBP. No
warranty is given for products or com-
ponents manufactured by companies
not affiliated by ownership with TFBP
or for products and components which
have been subject to misuse, improper
installation, corrosion, or which have
not been installed, maintained, modi-
fied or repaired in accordance with ap-
plicable Standards of the National Fire
Protection Association, and/or the
standards of any other Authorities
Having Jurisdiction. Materials found
by TFBP to be defective shall be either
repaired or replaced, at TFBP's sole
option. TFBP neither assumes, nor
authorizes any person to assume for it,
any other obligation in connection with
the sale of products or parts of prod-
ucts. TFBP shall not be responsible for
sprinkler system design errors or inac-
curate or incomplete information sup-
plied by Buyer or Buyer's repre-
sentatives.
In no event shall TFBP be liable, in
contract, tort, strict liability or under
any other legal theory, for incidental,
indirect, special or consequential dam-
ages, including but not limited to labor
charges, regardless of whether TFBP
was informed about the possibility of
such damages, and in no event shall
TFBP's liability exceed an amount
equal to the sales price.
This limited warranty sets forth the ex-
clusive remedy for claims based on
failure of or defect in products, materi-
als or components, whether the claim
is made in contract, tort, strict liability
or any other legal theory.
This warranty will apply to the full ex-
tent permitted by law. The invalidity, in
whole or part, of any portion of this
warranty will not affect the remainder.
Ordering
Procedure
When placing an order, indicate the
full product name. Refer to the Price
List for complete listing of Part Num-
bers.
Contact your local distributor for avail-
ability.
Sprinkler Assemblies with NPT
Thread Connections:
Specify: (Specify Model/SIN), Stand-
ard Response, (specify K-factor),
(specify temperature rating), Series
TV-B (specify Pendent or Upright)
Sprinkler with (specify type of finish or
coating), P/N (specify from Table C).
Recessed Escutcheon:
Specify: Style (specify 10 or 40 ) Re-
cessed Escutcheon with (specify*) fin-
ish, P/N (specify*).
Refer to Technical Data Sheet TFP770.
Sprinkler Wrench:
Specify: W-Type 6 Sprinkler Wrench,
P/N 56-000-6-387.
Specify: W-Type 7 Sprinkler Wrench,
P/N 56-850-4-001.
TYCO FIRE & BUILDING PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446