Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
1969 PALOMAR OAKS WAY; ; FS060005; Permit
City of Carlsbad Fixed Systems Permit Permit No: FS060005 1969 PALOMAR OAKS Job Address: Status: ISSUED WY Permit Type: FIXSYS Applied 4/6/2006 Parcel No: 2130922000 Approved: 4/19/2006 Lot #: 0 Reference No.: Issued: 4/19/2006 PC #: Inspector: Project Title: SCHUMACHER SUPPRESSION SYSTEM PLAN CHECK & INSPECTIONS (. Applicant: SCHMIDT FIRE PROTECTION CO INC 4760 MURPHY CANYON RD SAN DIEGO, CA92123. 858-279-6122 Owner: AIR PRODUCTS&CHEMICALS INC C/O J C SCHUMACHER CO• 1969 PALOMAR OAKS WAY CARLSBAD CA Fees ($) Add'l Fees ($) • Total ($) : Balance ($) 120 .0 • . 120 . 0 - - tSchmiiIt Fire Protection Co., Inc. 141 4760 MURPHY CANYON RD • SAN DIEGO, CA 92123• (858) 279-6122 • FAx (858) 279-3583 SCHUMACHER 1969 PALOMAR OAKS WAY CARLSBAD, CA 92009 (1) CO2 FIRE SUPPRESSION SYSTEM BTBAS RGA HOOD eaoWiz&m • cewkàz of ce ckp"kt ckEd&m p 1 KIDc200 Kidde Fire Systems CO2Calc KID2.00a Project: New BTBAS RGA Hood File Name: C:\KIDC200A\PROJECTS\RGAREAl.CO2 Calculation Date/Time: Mar 27, 2006, 12:57:05 PM Project Report Distributor Name: Address: SCHMIDT FIRE PROTECTION CO. 4760 MURPHY CANYON RD. SAN DIEGO,. CA Phone: PH: 858-279-6122 FAX: 858-279-3583 Customer ---- Name: . Schumacher Address: 196'9 Palomar Oaks Way Carlsbad, CA 92009 Phone: Contact: Title: . • • ---- Project Project: New BTBAS RGA Hood Designer: Gary .Formway Number: NICET #077137 • Account: • Location: • Desc.: Kidde High Pressure CO2 Total Flooding Fire Suppression System . 0 Page: 1 KIDc200 Kidde Fire Systems CO2Calc KID2.00a Project: New BTBAS RGA Hood File Name: C:\KIDC200A\PROJECTS\RGAREAl.CO2 Calculation Date/Time: Mar 27, 2006, 12:57:05 PM Designer Notes Report • Prelirninär Design by Gary Formway 3/27106. Page: 2 I KIDc200 Kldde Fire Systems CO2Calc KID2.00a Project: New BTBAS.RGA Hood File Name: C:\KIDC200A\PROJECTS\RGAREA1.0O2 Calculation Date/Time: Mar 27, 20061 12:57:05 PM • Hazard Report Type Of CO2 System: Total Flooding • Design Total Discharge: 1.0 minutes • Design Liquid Discharge: 0.7 minutes Hazard Number: 1 • • Name: New BTBAS RGA Hood Type Of Hazard: Total Flooding: Number of Nozzles: 1 • • Agent Required: 50.0 lbs • • Estima1ed Flow Rate: 50.0 lbs/mm • • • • .• fl Page: 3 KIDc200 Kidde Fire Systems CO2Ca1c KID2.00a Project: New BTBAS RGA Hood File Name: C:\KIDC200A\PROJECTS\RGAREA1.0O2 . Calculation Date/Time: Mar27, 2006, 12:57:05 PM Agent Source Report • Agent: CO2 High Pressure . Adjusted Agent Required: 50.0 lbs. . • Cylinder Name: 50 lb. cylinder, upright Cylinder Part Number: 982548 •, . Number of Main Cylinders: 1 Number of Reserve Cylinders: 0 • • Manifold: No Manifold • Agent Per Cylinder: 50.0 lbs Total Agent Quantity: 50.0 lbs Weight, Empty Cylinder: 105.0 lbs • • . Weight, All Cylinders + Agent: 155.0 lbs Floor Area Per Cylinder: 0.39 square ft . • Floor Loading Per Cylinder: 393 lbs / square feet • .• • S S Page: 4 KIDc200 Kidde Fire Systems CO2Calc KID2.00a Project: New BTBAS .RGA Hood File Name: C:\KIDC200A\PROJECTS\RGAREAI .CO2 Calculation Date/Time: Mar 27, 2006, 12:57:05 PM Pipe Network Report PART 1- PIPE . --- Node -- -------------------- Pipe ------ ----------- Description Start End Type Diameter Length Elevation, Main Cyl. X 1 1 2 -------------------------------------------------------------------- 1/2 in 4.58 ft 5.00. ft Flex Hose 2 3 1/2 in 0.63 ft - Flex Hose 3 4 1/2 in 0.58 ft .0.58 ft Stop Valve 4 5 1/2 in 0.10 It 0.10 ft Pipe 5 6 40 TC 1/2 in 2.00 ft 2.00 ft Pipe 6 7 40 TC 1/2 in 2.00 ft - Pipe 7 8 40 TC 1/2 in 3.00 ft Pipe 8 9 40 TC 1/2 in 1.00 ft 1.00 ft Pipe 9 10 40 TC 1/2 in 14.50 ft - Pipe 10 11 40 TC 1/2 in 3.00 ft - Pipe/H1-T01 11 12 40 TC 1/2 in 1.00 ft -1.00 ft PART 2 - EQUIVALENT LENGTH • -Node-- ----- ---- Pipe Parts ------------ Equivalent Length Str End 90 45 Thru Side Union Other Added Total 1 2 - - - - - . • - 71.0 ft • 2 3 - - - - - FlexN]. . - • 1.0 ft 3 4 1 - - - - FlexN2 - 1.0 ft 4 5 - -. - - - SV 1/2 in - . 11.0 ft 5 6 - - - - - - 2.0 ft 6 7 1 - - - - - 3.1 ft 7 8 1 - - - - • - 4.7 ft 8 9 1 - - - - - 2.7 ft 910 1 - - - - - 16.2 ft 10 11 1 - - - - - 4.7 ft 1112 1 - -. - - - 2.7 ft PART 3 - PRESSURE --- Node -- --------- -- Pipe -------------Required psia Start End Type Diameter ------------------------------------------------------------------- Length Agent Start End 1 2 1/2 in 4.58 ft 50.0 lbs 750 737 2 3 1/2-in 0.63 ft 50.0 lbs 737 737 3 4 1/2 in 0.58 ft 50.0 lbs 737 737 4 5 1/2 in 0.10 ft 50.0 lbs 737 736 5 6 40 TC 1/2 in 2.00 ft 50.0 lbs 736 735 6 7 40 TC 1/2 in 2.00 .ft 50.0 lbs 735 735 7 8 40-TC 1/2 in 3.00 ft 50.0 lbs 735 735 . 8 9 40 TC 1/2 in. 1.00 ft 50.0 lbs 735 735 9 10 40 TC 1/2 in 14.50 ft 50.0 lbs 735 733 Page: 5 4 10 11 40 TC 1/2 in 3.00 ft 50.0 lbs 733 .733 11 12 40 T.0 1/2 in 1.00 ft 50.0 lbs 733 733 PART 4 - NOZZLE . . . . . . . . -Node-- Required -------------Nozzle --------------- __________ Str End Agent Name Diameter Type Orifice Code. 1 2 50.0 lbs . . 2 3 50'0 'lbs . 3 . 4 .50.0 lbs . . . . .. . 4 5 50.0 lbs . . 5 6 50..0 lbs . . . 6 7 50-.0 lbs . . . 7 8 50.0 lbs 8 9 50.0 lbs .. . 9 10 50.0 lbs . 10 11 50.0 lbs . . . . .. 11 12 50.0 lbs H1-T01 1/2 in S . .• 4 . . Page: 6 V KIDc200 Kidde Fire Systems CO2Calc KID2.00a Project: New BTBASRGA Hood File Name: C:\KIDC200A\PROJECTS\RGAREA1.0O2 Calculation Date/Time: Mar 27, 2006, 12:57:05 PM Part List Report Cylinder(s) . --------------------------------------------------------------- Count Part # 50 lb. cylinder, upright 1 .982548 Manifold Type: No Manifold . Manifold Parts . . Description Length/Count No parts found. . ... Main. Pipe System Description . . Length/Count . Pipe - 40 TC - 1/2 in 26.50 ft Elbow(s) 90 - 1/2 in 6 1/2 in. Stop Valve 1 Flex Hose 90 Degree . . 1• • • • Nozzles Type Code Count • Part # 1/2 in S • 4.0 1 803368 Page: 7 KIDc200 Kidde Fire Systems CO2Ca1c KID2.00a Project: New BTBAS RGA Hood File Name: C:\KIDC200A\PROJECTS\RGAREAl.CO2 Calculation Date/Time: Mar.27, 2006, 12:57:05 PM System Acceptance Report System Type: Total Flooding Cylinder Name: 50 lb. cylinder, upright Number of Main Cylinders: 1 Number of Reserve Cylinders: 0 Manifold: No Manifold Total Design Discharge Time: 1.0 minutes Liquid Discharge (Designed): 0.7 minutes Calculation based on 70 degree Fahrenheit pre-discharge pipeline temperature. Total Flooding Nozzle Summary Calced Calced Designed Total Selected Calced Designed Mass Total Time Nozzle Nozzle Press Mass (liq&vap) Time (liquid) ' Nozzle Code Code (psia) (lbs) (lbs) (mm) (mm) Hi-TO1 4.0 3.98 733 50.0 50.0 1..0 0.7 Additional Nozzle Information Liquid End Of Fluid Initial Dischrg Liquid* Mass Vapor Time Time NozzlelDiameteriType Type (lbs) (sec) (sec) (sec) H1-T01I1/2 miS Total 50.0 1.1 .42.3 43.4 End of Report Page: 8 K1Dc2UJ kc].aae lire systems zLaic rwz.uua Isometric View #: 1 Standard Isometric View File ame: C:\KIDC200A\PROJECTS\RGAREAl.CO2 Calculation Date/Time: 3/27j2O.06 12:57:05 PM Page :...9 . 0 .0 S 0 H . . S' NOZZLE (CODE 4.0) ON}'xl-ODROP DETECTOR 12 Hi-TO! rI0ZZLE PENETRATION PIPE @ 8'-" ABOVE FINISHED FLOOR WARM G SIGN (SEE Er, JL BELOW) 8 14. . " LOCKOUT VALVE ' FLEX HOSE ELECT. CONTROL HEAD 2 24VDC.: CD NOTE: ALL " PIPE TO BE SCH. 40 . 1 50 LB CO CYLINDER ' ) 2 ALL MEASUREMENTS ARE CENTER TO CENTER. : . ALL PIPE TO BE CLEANED. :. . ALL FITTINGS TO BE 300LB.: MIN. RATED MALLEABLE IRON. . . "S" NOZZLE TO PENETRATE TOP OF LAB HOOD. . • • MlGDDE-@' U 50 LB., 75 LB., 100 LB. CARBON DIOXIDE CYLINDERS CONTROL PORT COMPONENT DESCRIPTION TYPE 'I' CYLINDER VALVE THREAD FOR SCHARGE HEAD SAFETY DISC ASSEMBLY THREAD FOR OTECTIDN CAP YLINDER SIPHON TUBE MATERIALS: CYLINDER: STEEL VALVE: SEE K-1040 FOR SEE K-1050 FOR SIPHON TUBE: ALUMINUM PRODUCT USE CO2 x FE-13 FM-200 HALON 1301 PART VALVI NUMBER CYLINDER TYPE 982528 50 LB 1/2' 870287 75 LB 5/8' 870269 100 LB 5/8' FOR DIMENSIONS AND ADDITIONAL DATA, SEE K-103 P/N - SEE TABLE. K-1010 ---'OIGDDE@ WF-~_ COMPONENT DESCRIPT CARBON DIOXIDE CYLINDER DATA PART NUMBER CYLINDER CO2 CAPACITY VALVE SIZE SAFETY DISC SIPHON TUBE.. DIM. "A" (HEIGHT) LBS KG IN.. MM 870269 100 45.3 5/8" RED STRAIGHT 62 1570 870287 75 34.0 5/8" RED STRAIGHT. 60 1520 982548 50 22.6 1/2" WHITE BENT 55 1390. 982547 35 15.8 1/2" WHITE BENT . 40 1010 870486 25 . 11.3 1/2" WHITE BENT 30 . 760 PART NUMBER DIM. BOB" (DIAMETER) . CYLINDER VOLUME NOMINAL CHGD. WEIGHT DOT CYLINDER SPECIFICATIOI IN MM IN M3 LBS KG 870269 10.50 266 4070 0.0667 288 130.6 3M-2300 870287 9.25. 234 3055 0.0501 205 92.9 3M-2300 982548 .8.50 215 2300 0.0377 155 70.3 3A-2015 982547 8.50 215 1510 0.0247 114 . 51.7 . 3A-2015 870486 8.50 215 1040 0.0170 84 38.1 3A-2015 . UNJ1W STAM DRTMD1T OF ThN4SPORTAflON 1] PRODUCT USE Co2 x FE-13 FM-200 HALON 1301 K-i' MIMDDE-0 00MPONENT DESCRIPTION 1PP CARBON DIOXIDE SINGLE CYLINDER STRAPS 1 101 1 0 1_D .Iu.. .•C WI t PART NUMBER CYLINDER SIZE A B C D E R IN MM IN MM IN MM IN MM IN MM IN MM 270012 10 6.22 15.8 9.81 249 8.75 222 1.00 25.4 2.62 66.5 3.41 86.6 270013 15 & 20 6.44 164 10.8 274 9.63 245 1.00 25.4 2.36 60.4 3.88 96.6 270014 25. 35. & 50 7.94 202 11.5 292 10.4 264 1.00 25.4 3.50 88.9 4.25 108 62669 75 5.63 143 12.3 312 11.1 282 1.25 31.8 3.75 95.2 4.63 118 270157 100 10.0 1 254 14.0 1 356 12.4 1 315 1.75 44.4 1 4.50 114 5.31 135 MATERIAL: STEEL PRODUCT USE CO2 x FE-13 LFM-200 I HALON 1301 P/N - SEE TABLE K- 1230 KIDDE COMPONENT DESCRIPTION.-. DISCHARGE HEAD, PLAIN NUT 3.81' (97mm) PISTON . 0 STOP CHECK 3.94' (100mm) BALL RETAINE - BALL CHECK SPRING DISCHARGE"": 3/4' NPS _--- 2 1/2 - 14N3 SET POSITIC OPERATED POSITION SWIVEL NUT (FOR CONNECTION TO CYLINDER VALVE) OUTER 0-RING P/N 242466 INNER 0-RING P/N 242467 STEM PRODUCT USE CO2 x FE-13 FM-200 HALON 1301 MATERIALS BODY' BRASS 0-RINGS' RUBBER SPRING' STAINLESS STEEL BALL CHECK' MONEL STOP CHECK' BRASS P/N - 8724k K-1060 14.5' IR CRI OSE FEMALE SWIVEL COUPLING- 3/4' NPS A PRODUCT USE CO2 x FE-13 fM-200 HALON 1301 P/N - 252184 K-1080 COMPONENT DESCRIPTION: a. flEX HOSE 1/2" COMPONENT DESCRIPTION • H CONNECTION FOR FLEXIBLE ELECTRIC CONDUIT- 3/4" NPT FEMALE LOCKING PIN . • . IffI I'I SO. DDEM ELECTRIC CONTROL HEAD 71 SEAL WIRE 6.1 aEM (r " 1 m) , 4 INDICATOR AND—. RESET STEM 0 . _I - 4.00"- . (1 02mm) LOCAL MANUAL RELEASE LEVER SWIVEL NUT.. 1.50" (38mm) HEX 1-1/4"-18 NF3 THREAD PART NUMBER CONTROL HEAD VOLTAGE AMPS WK-890181-000 24 VOC 2.0 81-890149-000 125 VDC 0.3 I WK-890165-0001 115 VAC 1.0 [ PRODUCT USE Tco2 . x X - FM-200 X -. [HALoN 1301 X P/N - SEE TABLE K-8010 PRODUCT USE CO2 • x -13 HALON 1301 r L COMPONENT DESCRIPTION I MULTIJET NOZZLE, TYPE "S" FLANGED STRAINER - INCLUDED IN TYPE 'S NOZZLES WITH NOZZLE CODE NOS. FROM 2 TO 5+ IAT :LE CODE NUMBER IPED HERE 4.25' (108mm) MATERIALS NOZZLES COLD ROLLED STEEL THROAT' BRASS STRAINER, MONEL AVAILABLE FINISHES (NOZZLE ONLY) RED PAINT CADMIUM PLATED P/N. - SEE K- 1170 K-1140 .1 CO2 Component Description fKidde Fire Systems: Warning Nameplate U.S. Coast Guard Approved Effective: April 2002 W . K819020 - - 9.001"— (229 mm) WHEN ALARM SOUNDS VACATE AT ONCE (127 mm) CARBON DIOXIDE BEING RELEASED 0.34" J \ . (9 MM) 4-9/32" (7 mm) HOLES USE 1/4" HARDWARE FOR FASTENING MATERIAL: ALUMINUM WITH RED PAINT LETTERS . This literature is provided for informational purposes only. KIDOE-FENWALINC. assumes no Kidde Fire Systems I responsibility for the product's suitability for a particular application. The product must be prop. j 400 Main Street laity applied to workcorrectly. I Ashland, MA 01721 USA I If you need more information on this product, or if you have a particular problem or question, Icontact KIDDE-FENWAL INC.. Ashland. MA 01721. Telephone: (508) 881-2000 Tel: (508) 881-2000 _________________________________________________________ • Fax: (508) 881-8920 K-81-9020 04/02 ©2002 Kidde-Fenwal, Inc. Printed in U.S.A. http://www.kiddefiresystems.com ScorpioTM Fire/Suppression Effective: July 2000 Control Panel GENERAL FEATURES Microprocessor Based Multiple Abort/Releasing Modes 14 Status Indicating LEDs 5 Diagnostic LEDs Programmable Alarm Relay Single or Dual Solenoid Release Programmable Delays Programmable Release Circuit Isolate Programmable Cross Zone Operation 24 Hour Trouble Resound Supervised Abort, Manual Release and Supervisory Circuits Transient and Noise Protection Listings: UL, FM, ULC, MEA, CSFM S DESCRIPTION The SCORPIO is a low cost control panel that supervises and controls one fire suppression hazard. Microprocessor technology enhances reliability and field programmable ver- satility. The control unit is compatible with KIDDE FM-2000, FE13, CO 2V Industrial Dry Chemical, and Restaurant Wet Chemical suppression systems. It meets requirements of NFPA 72 and - additional to extensive listings - is approved for use in suppression systems covered by NFPA codes: 12, 12A, 17,17A and 2001. The control panel provides 14 indicating status LEDs and 5 diagnostic LEDs: Indicating status LEDs are AC power Zone I Alarm and Trouble Zone 2 Alarm and Trouble Alarm Silence Supervisory ON Supervisory Trouble System Trouble Manual release Alarm and Trouble Release output Trouble Abort Active and Trouble Diagnostic LED indications are: AC Fault Ground Fault Battery Fault Signal circuit Open Signal circuit Short Field programmable options include: multiple time delays, 3 abort modes, single or cross zone operation, release circuit isolation, and a second alarm relay programmable to oper- ate on actuation of 2nd cross zone or agent release. Programmable abort modes are: Mode I - Timer hold at 10 seconds, count down upon abort release Mode 2 - Timer reset to initial value, count down upon abort release Mode 3 - Timer hold at 10 seconds if actuated be- fore 2nd alarm, count down upon abort release (IRI) The SCORPIO has two independent style NB initiating cir- ORDERING INFORMATION cuits that can be programmed for single or cross zone appli- DESCRIPTION PART NO. cation. The circuits support 15 Fenwal 2-wire CPD/PSD S type smoke detectors which can be intermixed with DETECT- Scorpio Control Panel, UL, I20VAC. 84-232000-102 A-FIRE® contact type, rate compensated thermal detectors. Scorpio Control Panel, UL, 240VAC 84-232000-104 Also, style "Ba abort, manual release and supervisory cir- Scorpio Control Panel, LJLC, I20VAC 84-232000-202 cuits are provided. All input circuits permit up to 50 ohms Scorpio Control Panel, ULC,24OVAC 84-232000-204 resistance thus allowing extended wiring runs. One style Y signal circuit is rated 0.5 amps © 24VDC. Battery, 12VDC, 1.2AH (2 required) 06-115915-020 The control unit will activate one or two 24VDC control heads Accessory kit: 50- 10K EOL resistors 06-129520.001 (Kidde part number 48650001, 899175 or 890181) to be used Extra Operating Instruction Sheet 06-235795-001 with either pre-engineered or engineered suppression sys- Spare Scorpio Circuit board 06-129800-002 tems. Extra Scorpio Key • 06-118013-001 The control panel 24VDC power supply - provided for either 120 or 240VAC input - features electronic power limited overload protection and built-in battery charger. Optional panel mounted, 1.2 amp-hour batteries (Kidde part number 06-115915-020) provides 24 hours of standby followed by 5 minutes alarm operation. See ORDERING INFORMATION for optional Canadian (ULC) version. SPECIFICATIONS Input power: 120 or 240VAC, 0.5 or 0.25 amp maximum Power Requirements: 35mA - standby • 200rnA - alarm Auxiliary power: 0.25 amps @ 24VDC in alarm only Input circuits: Two style "B, 50 ohms, 10K EOL resistor Auxiliary input One Supervisory, Manual Release circuits: and Abort, style NBa, 10K EOL Output circuit: One style ND, 0.5 amp @ 24VDC, 10K EOL Relay outputs: Two alarm, one trouble, form C", rated 2 amp © 24VDC. 2d alarm relay programmable Release output: Activate one or two p/n 48650001, 899175 or 890181 Isolation switch: Disconnects Release Output, cut jumpers WI and W2 and operate switch 2-4. Time Delay to Field selectable: 0, to 60 seconds Discharge in 10 second increments (detectors only): Nominal dimensions: 13.25H x 11.0"Wx 2.3D S IThis literature is provided for informational purposes only. KIDDE.FENWiiL.INC. assumes nol lresponsibility for the products suitability for a particular application. The product must be prop-I leily, applied to work correctly. III you need more information on this produd, Cr if you have a particular problem or question, I contact KIODE-FENWAL INC.. Ashland. MA 01721. Telephone: (508) 881-2000 Fire Systenis 84-03.1 07100 Kidde-Fenwal Inc. Printed in USA - Kidde-Fenwal Inc. 400 Main Street. Ashland. MA 01721 Tel: (508) 881-2000 Fax: (508) 881.8920 http:IMww.kiddellresystems.co,n WE Welcome to the world of [ UI FB'IWAL Fire Protection! KIDDE-FENWAL Scorpio Control Panel (Information forthis Calculation Form Is taken from the KIDDE.FENWAL SCORPIO InstallatIon. Operation, and Maintenance Manual) Date: 05-Apr-06 Project: SCHUMACHER 1969 Palomar Oaks Way Carlsbad, CA 92009 New BTBASRGAHôod BATTERY CALCULATIONS DEVICE QUANTITY Standby Current Load Total Standby Current Load Alarm Current Load Total Alarm Current Load 4 nnc fl fl nmn 0.2 nmn 0.2 amo Control Release Head* 1 0 amp 0 amp 0 amp 0 amp Maximum number of Release Devices Is 2. 15 cd Horn/Strobe 2 - 0.134 amp 0.268 am 30 cd Horn/Strobe f_Maximumcurrent load is .5 amps. 0.137 amp 0 am 75 cd Hom/Strobe 0.134 amp 0 amp Thermal Detector 1 0 amp 0 amp 0 amp • 0 am Maximum number of Smoke Detectors per circuit Is 15. Ion Detector 0 0.0001 amp' 0 amp 0.1 amp 0 am Maximum number of Smoke Detectors per circuit is 15. Total amps used in Standby: 0.035 amp Total amps required for 24 hours Standby 0.84 AH S Total Backup Battery Provided: 1.2 AH Total Backup Battery Required: 0.918156 AH Total Backup Battery Reserved: 0.281844 AH Control Release Head has momentary current draw; 0 draw for calc purposes. Total amps used in Alarm: 0.468 amp Total amps required for 10 mm. of Alarm: 0.078156 AH • .. SCHUMACHER 1969 PALOMAR OAKS WAY NOde :.• 'Unft m.. Unit ,.sTotal " Cond: AWG OhrniPer: Voge' erceflt' Re?erence '' .'Y Volt.' ' ' - :' *mps. Amps : Feet. • sin' :, . FOot'' Drop: Volt Drop. '.•• ACTUATOR 24 0.2000000 0.200b060 5 14 ' . '. 0.0052 ..: 0.0052555 0.0219% Total • Percentage Amps Conductor • Voltage Drop Voltage Drop I TOtalS :.•. . ' 0.200 -' . .; 0.005255474 111 4/51068:32 AM Page 1 of I S SCHUMACHER . S 1969 PALOMAR OAKS WAY Nod! :.i:: :U'Y Tta1.;.. Uflft • Cofld: . AWG.. Oh. .Per Reteience Volta : Amps . Amps Size. .,. .Foo..:;DópVbltDr.op A-IND 1 24 0.1340000 C.1340O00 15 14 00052 0.0105635 0.0440% Total Percentage Amps Conductor Voltage Drop Voltage Drop L Totals. s. 5 .0:1:34000 -15. . . 0.01O56350.:*00440%j S I * 4/5/068:39 AM Page 1 of 1 .. SCHUMACHER 1969 PALOMAR OAKS WAY IIWU [IndkaUng circuitil. 4 E)CMihod z :ReIèrence: .::.-. Volt . Unit. Total::cofld Amps. Amps ...AWG.. :Ohrns Per Feet .... Foot Wage :PeTceflt; voft:orop B-IND 1 24 0.1340000 0.1340000 Total Amps 5 14 0.0052 Conductor . 0.0035212 Voltage Drop 0.0147% Percentage Voltage Drop I.• Totals: .: . 0134000 .; .5 .• . .0.003521168. 0M147%- 0 4151068:39 AM ~LUiI 10 r, D-1-FOICAT I FICA Im< 11-0 ~~22 / RCA ?LE AftI ROOM rIi I sci. 40 FIRM I Y i{ APPROXIMATELY 8'-6'/ A,FF(0'I6'l ABOVE '.UR AC[MUUN T SCURPIE] C1JNT RFJL PANEL w/ PULL STATIUN 'AND 13/75 CD HURN / ST RU BE. T-I3AR [jRiii) FkB.CO -1 \—MAJNrENANCE SWITCH PIIN6 PL-AN J/411 1l-oil mom 810 or 811 shown with Fire Alarm Label Installed FIRE ALARM OR SUPPRESSION RELEASE LABELING The Kidde 1310 and B1 Manual Pull Stations have a unique labeling method which provides the installer the greatest amount of flexibility. Six labels are shipped with each station: FIRE ALARM FIRE SYSTEM RELEASE FM-200 RELEASE FE-13 RELEASE CO2 RELEASE HALON 1301 RELEASE These permanent, heavy-duty Lexan® self-adhesive labels are die-cut with raised lettering. During instal- lation, the installer simply chooses the appropriate label, removes the protective backing, and places the label into the space on the top of the station. This flexibility allows installations to be customized for each customer, without the expense of having to carry extra inventory. Manual Stations Series Bi 0 & Bi 1 EFFECTIVE January 1997 84.05 S FEATURES Exclusive KIDDEO Design Unique Field Labeling for either Fire Alarm or Suppression Applications Dual Action Operation Single Pole or Double Pole Keylock for Reset and Test UL Listed and FM Approved cUL Listed for Canada ADA Compliant CSFM Listing (pending) MEA Approval (pending) Optional Weatherproof Box DESCRIPTION The Kidde 1310 and 811 Manual Pull Stations are high quality, reliable non-coded alarm initiating devices based upon a proven design. They are con- structed of heavy die-cast aluminum for long life and . reliability. These manual stations have the exclusive Kidde look, with gloss red paint with raised white let- tering, and black sides with a white trim border. The B10 station has a standard single pole single throw switch, while the Bli has a double pole single throw switch for local annunciation or remote signal- ing. Switches are gold plated for reliability when used in low current initiating circuits. These manual stations are designed for quick, effi- cient response by personnel in an emergency, while the standard double action PUSH/PULL levers pre- vent accidental operation. The keylock allows the unit to be easily reset and tested, and the stations are keyed to match the Kidde Scorpio'TM, PEGAsysTM, and OrionTM control panels. Optional surface backboxes are available, which are painted red and sized to match the manual stations. The SGB-32S is UL Listed for indoor use, and the SGB-32C cast aluminum weatherproof box is UL Listed for outdoor use. The weatherproof box comes with a gasket kit which allows either the B10 or 811 to be mounted outdoors. OPERATION The dual action B10 and Bli manual stations are S operated by simply pushing the PUSH bar inwards, allowing the PULL handle to be grasped in a one- handed motion. The handle is then pulled down as far as it will go. If the optional breakrod is installed, it would break at this point. The handle is now locked in place, and is easily visible from up to 50 feet away. The handle is reset by opening the sta- tion with the key, placing the handle in the normal upright position, and, re-locking the station. SPECIFICATIONS B10 & Bli Manual Pull Stations Style: Double Action, non-coded. Dimensions: 4.75"H x 3.25W x 1 "D Contact: B10: Single Pole, Single Throw Bil: Double Pole, Single Throw Contact rating: 1 amp © 125VAC or 30VDC Gold plated contacts. Wiring: Terminal block connections with clamping plate for in & out wiring. Suitable for up to 12AWG wiring. Mounting: Mounts to a standard single gang box, or the SGB-32S or SGB-32C S . surface boxes. Two 6/32 screws ship with each unit. Keylock: Keyed to match Kidde ScorpioTM, PEGAsysTM, and OrionTM control panels. One key ships with each unit. Breakrod: Optional, order separately. Constructed of clear acrylic tubing. Visible from front of unit if broken. Temperature: -12°F to 132F (-25°C to 56C) SGB-32S Interior Surface Backbox Range of labels supplied with 810.and Bil SGB-32C Weatherproof Surface Backbox Dimensions: 4.75"H x 3.25°W x 2.25"D Construction: Cast aluminum. Conduit One threaded opening for 1/2" conduit connector. Mounting: 1310 or BI mounts to the box with (4) 8/32 screws and a foam gasket, which ship with each box. ORDERING INFORMATION Part Number Description Shipping Weight 84-100007-001 B10 Pull Station SPST Includes six labels. 1.2 lb 84-100007-002 Bil Pull Station DPST Includes six labels. 1.3 lb 84-100009-001 SGB-32S Indoor Box .8 lb 84-100009-002 SGB-32C Outdoor Box 84-100008-002 Pkg. of (12) Breakrods Must order separately. >25 lb 06-118013-001 Spare Key for B10/1311 >25 lb DIMENSIONS (shown with Fire System Release Label installed) EBONLEW 8EW Dimensions: 4.75"H x 3.25W x 2.25"D I Construction: Steel sheet metal. Conduit Two knockouts for 1/2° conduit connectors, one on top and bottom. Mounting: B10 or Bli mounts to the box with (4) 8/32 screws, which ship with each box. —i-- . . . KIDDE. I This literature is provided to, informational purposes only. KIDDE.FENWAL INC. fire Systems assumes no responsibility for the products suitability for a particular application. The KIDDE.FENWAL. INC. product must be properly applied to perform as described herein. 400 MAIN STREET II you need more information on this product. or if you have a question, contact Kidde. ASHLAND, MA 01721 FENWAL. INC.. Ashland, MA 01721. (508) 881.2000. (508) 881.2000 FAX: (508) Sol -WO 84.05 2197 SM 01997 KIDDE-FENWAL. INC. Printed in U.S.A. CP "m VY I ! SYSTEMS 9~ J(®' Helping People Take Actions" SERIES MT AND MT STROBE MULTITONE ELECTRONIC APPLIANCES Description: Wheelock's Series MT and MT Strobe Multitone electronic appliances offer a choice of eight (8) nationally and internationally recognized alerting sounds: Horn, Bell, March Time Horn, Code-3 Tone, Code-3 Horn, Slow Whoop, Siren or Hi/Lo Tone. The Code-3 Horn and tone patterns are engineered to comply with NFPAIANSI Temporal Pattern specifications without requiring additional equipment. With MT and MT Strobe appliances, one alarm appliance meets most of your signaling needs. The MT strobes can be synchronized using the Wheelock SM, DSM Sync Modules or the PS-12/24-8MP and PS-12/24-8CP Power Supplies with Wheelock's patented Sync Protocol. The MT Strobes are designed for ADA applications while meeting or exceeding the latest requirements of NFPA 72, ANSI 117.1, UFC and UL Standard 1971 as well as meeting ADA requirements concerning photosensitive epilepsy. Each MT and MT Strobe appliance has two installer selective sound output levels: STANDARD dBA and HIGH dBA. Non-strobe versions provide selectable voltage capability in one unit, I2VDC or 24VDC. Strobe versions are specific for either I2VDC or 24VDC and all models may be used with filtered or unfiltered (full-wave-rectified) input voltages: Separate input terminals are available, shunt wires are provided to enable both tone and strobe to operate simultaneously from a single input. The Series MT Multitone Strobe appliances are UL Listed for indoor wall mount applications under Standard 1971 for Signaling Devices for the Hearing Impaired and under Standard 464 for Audible Signaling Appliances. MT4-115-WH SERIES MT w/o STROBE For Weatherproof MTWP See Data Sheet S9004 Copyright 2005 Wheelock, Inc. All rights reserved. SERIES MT STROBE Features: Approvals include: UL Standard 1971, UL Standard 464, California State Fire Marshal (CSFM), New York City (MEA), Factory Mutual (FM) and Chicago (BFP) See approvals by model in Specifications and Ordering Information Designed to meet or exceed ADA/NFPA/UFC/ANSl Standards and Accessibility Guidelines Complies with OSHA 29, Part 1910.165 Series MT appliances have-IN and OUT wiring terminations that accept two #12 to #18 American Wire Gauge (AWG) wires at each terminal. inputs are polarized for compatibility with standard reverse polarity type supervision One alarm appliance with (8) eight selective signals to provide superior sound penetration for various ambient and wall conditions with two field selectable sound output levels Code-3 Horn and Tone meet ANSI/NFPA temporal pattern for standard emergency evacuation signaling Audible and strobe can operate from a single NAC circuit or from separate NAC circuits with any of the (8) eight audible sounds MT Strobe models are available with Wheelock's patented MCW Multi-Candela strobes with field selectable candela settings at 15/30/75/110cd or with single candela 1575cd strobes. The strobes can be synchronized using Wheelock's sync modules or power supplies with built in Sync Protocol Selectable input voltage on non-strobe versions. Strobe versions are factory set for either 12 or 24VDC, with wide-Listed voltage range, filtered (DC) and FWR Mounts to either 4" square or double gang boxes (important for retrofit installations). Attractive flush or surface mounting No additional trimplate required for flush mounting I NOTE: All CAUTIONS and WARNINGS are identified by the symbol . All warnings are printed in bold capital letters. A WARNING: PLEASE READ THESE SPECIFICATIONS AND INSTALLATION INSTRUCTIONS CAREFULLY BEFORE USING SPECIFYING OR APPLYING THIS PRODUCT. FAILURE TO COMPLY WITH ANY OF THESE INSTRUCTIONS, CAUTIONS AND WARNINGS COULD RESULT IN IMPROPERAPPUCATION, INSTALLATION AND/OR OPERATION OF THESE E RODUCTS IN AN EMERGENCY SITUATION, WHICH COULD RESULT IN PROPERTY DAMAGE, AND SERIOUS INJURY OR EATH TO YOU AND/OR OTHERS. General Notes: Strobes are designed to flash at 1 flash per second minimum over their "Regulated Voltage Range" (16-334 for 24VDC units and 8-17.5v for I2VDC units). Regulated Voltage Range is the newest terminology used by UL to identify the listed voltage range. All candela ratings represent minimum effective Multitone Strobe intensity based on UL Standard 1971. MT Strobe models are UL Standard 1971 Listed for indoor use with a temperature range of 32°F to 120°F (0°C to 49°C) and maximum humidity of 93% ±2%. The MT-12/24, MTWP and MT4 models and listed for outdoor use at -31°F to 150°F (-35°C to 66°C) and maximum humidity of 95% (See Data Sheet S9004 or Installation Instruction Sheet P84150 for more detail on MTWP). MTWP and MT4 strobes are listed under UL 1638. MT Audible is UL Standard 464 Listed. Alarm Tones TONE ALARM TONES PATTERN DESCRIPTION HORN BROADBAND HORN (Continuous) BELL 1560 Hz MODULATED (0.07 sec. ON/Repeat) MARCH TIME HORN HORN (025 sec. ONI0.25 sec. OFF/Repeat CODE-3 HORN HORN (ANSI S3.41 Temporal Pattern) CODE-3 TONE 500 Hz (ANSI S3.41 Temporal Pattern) SLOW WHOOP 500-1200 Hz SWEEP (4.0 sec. ON/0.5 sec. OFF/Repeat) SIREN 600-1200 Hz SWEEP (1.0 sec. ON/Repeat) HIILO 1000/800 Hz (0.25 sec. ON/Alternate) Table 1: dBA and Current Ratings for Muitftone Audible Portion RMS Current (amps) dBA@ l Oft (UL Reverberant) dBA@ lOft (anechoic) dBA@ l Oft (UL Reverberant) 24 VDC 12 VDC 120 VAC 24 VDC 12 VDC 12 and 24 VDC 120 VAC HI Oulpul SW Output HI Output SW Output HI OutXd STD OUtpUt HI Output SID Output HI Output SW Output HI Output SW Output HI Output SW Output @ 24 VDC UL max" @ 24 VDC UL max" @24 VDC UL max" @24 voc UL max" UL max" UL max' Horn 0.074 0.108 0.033 0.044 1 0.145 0.176 0.023 0.034 0.050 0.042 92 87 90 77 99 93 Be 82 Bell 0.040 0.053 0.018 0.024 0.077 0.095 0.014 0.020 0.041 0.039 86 80 85 69 92 87 82 1 75 March Time Horn 0.067 0.104 0.033 0.038 0.109 0.142 0.023 0.034 0.050 0.040 89 84 89 74 99 93 85 79 Code-3 Horn 0.069 0.091 0.026 0.035 0.100 0.142 0.023 0.034 0.050 0.042 88 83 88 73 99 93 85 75 Code-3 Tone 0.061 0.075 0.026 0.035 0.088 0.105 0.015 0.021 0.042 0.040 85 80 84 70 95 90 79 75 Slow Whoop 0.069 0.098 0.028 0.037 0.100 0.142 0.025 0.035 0.050 0.042 90 89 89 75 99 94 88 82 Siren 0.080 0.104 0.027 1 0.036 0.122 0.152 0.021 0.030 0.045 0.041 89 84 89 75 98 1 93 85 82 HIILO 0.044 0.057 0.020 0.026 1 0.089 1 0.114 1 0.018 0.026 0.042 0.039 86 81 86 71 93 88 82 79 Table 2: Strobe Current Ratings RMS Current (amps) Model MT-121575 MT-241575 MTWP-2475 MT-24MCW Candela 1575cd 1575cd 1 80o 15cd 30cd 75cd llocd [áVDC 0.152 0.060 0.094 0.041 0.063 0.109 1 0.140 UL max" 0.255 0.090 0.138 0.060 1 0.092 0.165 0.220 S Note: If the strobe and audible operate on the same circuit, add the strobe current from Table 2 to the audible current from Table 1. * RMS current ratings are per UL average RMS method. UL max current rating is the maximum RMS current within the listed voltage range (16-33v for 24v units). For strobes the UL max current is usually at the minimum listed voltage (16v for 24v units). For audibles the max current is usually at the maximum listed voltage (33v for 24v units). For unfiltered FWR ratings, see installation instructions. Model Number Order Code Input Voltage Rated Candela Mounting Options°°° Agency Approvals UL MEA CSFM FM BFP. MT-12124-R 5023 12/24 - D,E,F,L,M,O,P,R X X X X X MT-12124-W 5024 12/24 - D,E,F,L,M,O,P,R X X X X X MT.241575WFR# 8422 24 15 (75 on AXIS) D.E.F.L,M.O,P,R X X X X * MT-24MCW-FR 3301 24 15/30175/110 D,E,F.L,M,O,P.R X * X * * MT-24MCW-FW 3303 24 15/30175/110 D.E,F.L,M.O.P.R X * X * * MT-121575W-FR' 8421 12 15 (75 on AXIS) D.E.F.L,M,O,P,R X X X X * MT-121575W-NW 9747 12 15 (75 on AXIS) D,E,F,L,M.O.P.R X X X X * M1WP-2475W-FR°° 8420 24 180 @ 77°F (25°C) M X X X X * MTWP.2475W-NW" 9744 24 180 @ 77°F (25°C) M X X X X MT4-115-R 6223 120 VAC - D, E. J. K, N. 0, R X X X X X MT4-115-S 6142 120 VAC - 0, E, J. K, N. 0, R X X X X X MT4115WH.VFRns .6224 120 VAC 15 0, E, J. K, N, 0, R X X X X X MT4-12/24-R 5308 12/24 - 0, E. J. K, N, 0, R X * * * * MT4-12/24-S 7997 12/24 - D, E, J. K. N, 0, R X S *Pending Wiring Diagrams (for all models) MT SIGNAL AUDIBLE SIGNAL AND STROBE AUDIBLE SIGNAL AND STROBE OPERATE INDEPENDENTLY OPERATE IN UNISON. RED AND FROM 0M + _______________ BLACK SHUNT-WIRES ARE PRECEDING , + TONBCT COMG EOLR M £C&R SWDSK J-LLL + TO NEXT PS-12124W. I I FRDIIPCIIG FROM PS.I2124MP I '# I _________________ PRECEDING APPLIANCE POWER I I S& + APPLIANCE. - . - APPLIANCE OR aiINE - - SUPPLIED. INWPUES I + - I• st APPLIANCE P51L2& SIGNAL - - - ° ORFACP - II1fj1I - OREOLR FACP L..._.._.__.J ER.E$ STROBE AUDIBLE Mon MLE Specifications and Ordering Information NOTE °°MTWP-2475W is Weatherproof and rated for 180 Cd @ 77°F (25°C). See Data Sheet S9004 or Installation Instruction P84150. —For additional information on mounting please refer to Data Sheet S7000. # 1575 strobes are UL Listed for 15cd with 75cd on AXIS. ## Series WH Strobe is listed for UL Standard 1638 only. See Instruction Sheet P83160. 4WARNING: CONTACT WHEELOCK FOR THE CURRENT "INSTALLATION INSTRUCTIONS" P82467 MT-12124, P84155 MT wl Strobe P84150 M1WP WEATHERPROOF "GENERAL INFORMATION" SHEET (P82380) ON THESE PRODUCTS. THESE DOCUMENTS DO UNDERGO PERIODIC CHANGES. IT IS IMPORTANT THAT YOU HAVE CURRENT INFORMATION ON THESE PRODUCTS. THESE MATERIALS CONTAIN IMPORTANT INFORMATION THAT SHOULD BE READ PRIOR TO SPECIFYING OR INSTALLING THESE PRODUCTS, INCLUDING: TOTAL CURRENT REQUIRED BYALLAPPUANCES CONNECTED TO SYSTEM SECONDARY POWER SOURCES. FUSE RATINGS ON NOTIFICATION APPLIANCE CIRCUITS TO HANDLE PEAK CURRENTS FROM ALL APPLIANCES ON THOSE CIRCUITS. COMPOSITE FLASH RATE FROM MULTIPLE STROBES WITHIN A PERSON'S FIELD OF VIEW. THE VOLTAGE APPLIED TO THESE PRODUCTS MUST BE WITHIN THEIR RATED INPUT VOLTAGE RANGE. INSTALLATION IN OFFICE AREAS AND OTHER SPECIFICATION AND INSTALLATION ISSUES. USE STROBES ONLY ON CIRCUITS WITH CONTINUOUSLY APPLIED OPERATING VOLTAGE. DO NOT USE STROBE ON CODED OR INTERRUPTED CIRCUITS IN WHICH THE APPLIED VOLTAGE IS CYCLED ON AND OFF AS THE STROBE MAY NOT FLASH. FAILURE TO COMPLY WITH THE INSTALLATION INSTRUCTIONS OR GENERAL INFORMATION SHEETS COULD RESULT IN IMPROPER INSTALLATION, APPLICATION, AND/OR OPERATION OF THESE PRODUCTS IN AN EMERGENCY SITUATION,WHICH COULD RESULT IN PROPERTY DAMAGE AND SERIOUS INJURY OR DEATH TO YOU AND/OR OTHERS. CONDUCTOR SIZE (AWG), LENGTH AND AMPACITY SHOULD BE TAKEN INTO CONSIDERATION PRIOR TO DESIGN AND INSTALLATION OF THESE PRODUCTS, PARTICULARLY IN RETROFIT INSTALLATIONS. is Wheelock products must be used within their published specifications and must be PROPERLY specified, applied, installed, operated, maintained and operationally tested in accordance with their installation instructions at the time of installation and at least twice a year or more often and in accordance with local, state and federal codes, regulations and laws. Specification, application, installation, operation, maintenance and testing must be performed by qualified personnel for proper operation in accordance with all of the latest National Fire Protection Association (NFPA), Underwriters' Laboratories (UL), National Electrical Code (NEC), Occupational Safety and Health Administration (OSHA), local, state, county, province, district, federal and other applicable building and fire standards, guidelines, regulations, laws and codes including, but not limited to, all appendices and amendments and the requirements of the local authority having jurisdiction (AHJ). Architects and Engineers Specifications The notification appliance shall be a Wheelock Series MT audible/visual appliance or equivalent. Notification appliance, shall c be electronic and use solid state components. Electromechanical alternatives are not approved. Each electronic appliance shall provide eight (8) field selectable alarm tones. The tones shall consist of: HORN, BELL, MARCH TIME HORN, CODE-3 HORN, CODE-3 TONE, SLOW WHOOP, SIREN and HI/LO. Tone selection shall be by durable dip switch assembly and not clips or jumpers. The Multitone Audible appliance shall be UL Listed under Standard 464 for Audible Signal Appliances. The. audible and the strobe shall be able to operate from a single NAC circuit while producing any of these tones. The appliance shall provide two output sound levels: STANDARD and HIGH dBA. The HIGH dBA setting shall provide a minimum 5 dBA increase in sound output at nominal voltage. The HIGH anechoic dBA measurement at 10 feet at the alarm HORN SETTING shall be 99 dBA minimum. Operating voltages shall be either 12 VDC or 24 VDC using filtered power or unfiltered power supply (full-wave-rectified). All models shall have provisions for standard reverse polarity type supervision and IN/OUT field wiring using terminals that accept #12 to #18 AWG wiring. Combination audible/visual appliances shall incorporate a Xenon flashtube enclosed in a rugged Lexane lens or equivalent with solid state circuitry. Strobe shall produce a flash rate of one (1) flash per second minimum over the voltage range. The MT strobe intensity shall be rated per UL and Listed under Standard 1971 for Signaling Devices for the Hearing Impaired for 1575cd multi-candela with field selectable 15/30/75/110 candela settings. The 1575 candela strobe shall be specified when 15 candela or with 75 candela intensity on-axis is required. Strobe Models shall incorporate circuitry for synchronized strobe flash and shall be designed for compatibility with Wheelock SM and/or. DSM Sync Modules or Wheelock's Power Supplies with Sync Protocol. The strobes shall not drift out of synchronization at any time during operation. If the module fails to operate (i.e., contacts remain closed), the strobes shall revert to a non-synchronized default flash rate. Strobe activation shall be via independent input or from the some input circuit as the audible. The combination audible/visual appliances shall be installed indoors and may be surface or flush mounted. They shall mount to standard electrical hardware requiring no additional trimplate or adapter. The aesthetic appearance shall not have any mounting holes or screw heads visible when the installation is completed. The appliance shall be finished in .a textured red color. The Series MT-12/24, MTWP and MT4 appliances maybe installed indoor or outdoor with the proper back box. NOTE: Due to continuous development of our products, specifications and offerings are subject to change without notice in accordance with Wheelock Inc. standard terms and conditions. n WE SUPPORT AND ENCOURAGE NICET CERTIFICATION ASSEMBLED IN THE USA 3 YEAR WARRANTY S National Sales Office 800-631-2148 Canada 800-397-5777 E-Mail: lnfo@wheelockinc.com hftp://www.wheelockinc.com Distributed By: 273 BRANCHPORT AVENUE • LONG BRANCH, NJ 07740 • TEL: 732-222-6880 • FAX: 732-222-2588 S200002105 12.01.5 DETECT-A-Fl RE® Detection and Release Devices DETECTION AND RELEASE DEVICES Respond Accurately and Positively to Fire Threats... Virtually Eliminate Costly False Alarms FEATURES Repeatable - resets Itself, nothing to replace, testable Rugged - withstands shock and vibration Versatile - offers various temperature settings Durable - long lasting stainless steel shell Economical - wide spacing, reduces installation cost Factory set and the internal contact area is hermetically sealed in stainless steel APPLICATIONS Protection of schools, factories, offices, libraries, etc. Paint spray booths Range hoods GENERAL INFORMATION DETECT-A-FIRE units are the 'heart' of many Fire Protection Systems. These highly reliable devices have been a standard of the industry for over 25 years. Many thousands of these units are now in use controlling the release of extinguishants such as clean agents, CO2. water, or dry chemicals. In some systems the device is used as an ALARM device, to sense overheat or fire, and alert personnel. In other systems, it is used as a RELEASE device, to sense fire and actuate fire attack systems. DETECT-A-FIRE units have met with wide acceptance because they are designed with RATE COMPENSATION. This provides a unique advantage over both fixed temperature and rate-of-rise types of detectors because only the DETECT-A-FIRE unit accurately senses the surrounding air temperature regardless of the fire growth rate. At precisely the predetermined danger point, the system is activated. Fixed temperature detectors must be completely heated to alarm temperature and therefore a disastrous lag in time may occur with a fast rate fire. Rate-of-rise devices, on the other hand, are triggered by the rate of increase in ambient temperature and are subject to false alarms caused by harmless, transient thermal gradientE such as the rush of warm air from process ovens. The secret of the unit's sensitivity is in the design (Figure 1). The outer shell is made of a rapidly expanding alloy which closely follows changes insurrounding air temperature. The inner struts are made of a lower expanding alloy. Designed to resist thermal energy absorption and sealed inside the shell, the struts follow temperature changes more slowly. A slow rate fire (Figure 2) will heat the shell and struts together. At the "set point," the unit will trigger, actuating the alarm or releasing the extinguishant. A transient rush of warm air up to 40F°/min. may expand the shell, but not enough to trigger the unit. By ignoring transient warm air excursions, the DETECT-A- FIRE unit virtually eliminates false alarms prevalent with rate-of-rise devices. If a fast rate fire (Figure 3) starts, the shell will expand rapidly. The struts will close, actuating the alarm or releasing the agent. The faster the fire rate of growth, the sooner the DETECT-A-FIRE unit will react. 5*1I.....HGH EXPANSION CONTACTS (CLOSED) CONTACTS (CLOSED) MF AT 135'F CONTACTS (OPEN) STRUTS-LOW EXPANSION A ALARM - 4 - (SURROUNDING (SURROUNDING AIR UMP) AIR TSMP) FIGURE 1 READY FIGURE 2 SLOW FIRE FIGURE 3 FAST FIRE A T IS/ DETECT-A-FIRE HORIZONTAL DETECT-A-FIRE-UNITS Horizontal detectors are designed for locations where appearance is a factor. The attractive, functional design lends physical protection of the unit while making it suit- able for commercial, industrial, mercantile and public buildings,, institutions, and ships in non-hazardous locations (those classified as'ordinary' under the National Electric Code). Flush mounted units are designed to fit standard 4 octogonal electrical boxes and surface mounting units are designed to mount directly on ceilings or on 4 electrical junction boxes. Canadian Electrical Codes requires mount- ing only to an electrical function box. VERTICAL DETECT-A-FIRE-UNITS - Vertical detectors are designed for use in both 'ordinary' or hazardous locations. For ordinary use, they may be mounted to any approved junction box with '/a diameter opening by using /2-14 NPT mounting nuts. The device may be wired in or out of conduit, depending on local preference'and code. Four leodwiies are provided on normally open vertical units (that close on temperature rise), per UL requirement, to facilitate supeMsion of system wiring. Instruments are Underwriters Laboratory and Underwriters Laboratory of Canada listed and Factory Mutual approved for hazardous locations, when mounted in a suitable fitting. MOUNTING Detect-A-Fire units are not position sensitive. Horizontal and vertical detectors refer to the most common mounting configuration for that unit. However, each type can be mounted either horizontally or vertically depending on the application and installation requirements. NOTE: Only units with stainless steel shell and head we approved for Class I. Group A locations. NOTE A: Spacings shown we distances between units on smooth ceil-ings; the distanées from partitions or walls would be half that shown. For specific spacing and agency approval, consult factor',. Authority having LOCAL jurisdiction should be consulted before installation. NOTE B: Temperature preset at factory only. Special settings available upon request. Consult factory or Fenwal.Representative for additional information. NOTE C: In applications where corrosion is suspect, care should be taken to protect the DETECT-A .FIPE unit to realize optimum performance,. and maximum life. Consult factory for suggestions. NOTE D: Up to 3757-418 AWG Teflon insulated wire used on units. Above 375T-h16 AWGTGGT insulated wire used on units. Si:,:zcaticnr subject :0 c'hongi wu10ut UL.;, Ccznadc !a.s:,c a caibie u,ra :qu.ct. AW:c.ugh i.iconcscenr lamps are ccside,e&,essut'e. Ib?r: :i:ri cuz,:rr 0. 15 the!, .cteadl' cent. l rot exceea iarrnp.c. HORIZONTAL DETECT-A-FIRE UNITS Flush Mounting Unit Surface Mounting Unit for Concealed Wiring for Exposed Wiring jT cAi 12427020-000 . 12427020-001 12427021-000 12427021-001 CONSTRUCTION Stainless steel shell sensing element. 'Cold rolled steel mounting facility. Off-White finish.. %'1992 Kidde-Fenwai, Inc. X riI xMIME I A4 I ! X X X .. . -• x x x x x x x x a DETECT-A-FIRE VERTICAL DETEC AFIRE UNITS VERTICAL DETECT-A-FIRE UNITS For Concealed and Exposed Wiring For Concealed and Exposed Wing (Hexagonal Head) (Coupling Head) 6LEADS 6"LEADS 6" LEADS 6" LEADS !/2.14NPTJJL 1/2.14NPTjjf(_ _____ -- f 14 NP? 14 NP? V. -T HEX •.: • ' I T" I 1 5•11r' f••5•7I8 3.66" j 3.656" 3.656" 3.656" • .• . H H'" • H. .:- H H'°" 12427120-000 12427121.000 12-X28020-003 12-X28021.000 12-X27120-022 12-X27121-020 12.X28021-005 CONSTRUCTION CONSTRUCTION -000 units have -a stainless steel sensing shell and a -000 units have a stainless steel sensing shell and a brass mounting head. -022 and -020 units are all Type • brass mounting head. -003 and -005 units are all Type 300 stainless steel. • 300 stainless steel. - '• ••- -' •,J_• DETECT-A-FIRE o I Figure 4. Dust Collector Application This is a typical application of DETECT-A-FIRE units used as a release device to actuate a complete &e suppression system. In this application DETECT-A-FM units are mounted in a Dust Collector to sense an overheat condition and release a clean agent extinguishant. This chart shows three categories.of fire detection devices and their relative response levels for reaction to three different rate of rise conditions. Statistics indicate that 97% MODIFICATIONS. 12-99202X-XXX, Extended lead wires, Series 12-X271XX and 12-X28XXX series only. 12-992012-XXX, Fluorocarbon coating, 12-X27IXX and 12-X28XXX series only (500°F max.). AGENCY LISTINGS Fenwal DETECT-A-FIRE units are UL and ULC listed and FM approved as fire detection thermostats (close on temperature rise) and as releasing devices (open on temperature rise). I I Figure 5. Typical ceiling installation of a horizontal DETECT-A-FIRE model. Here it is used in combination with a sprinkler system to detect overheat and actuate an alarm. HOW To ORDER Select the DETECT-A-FIRE model from specifications on pages 2 and 3. Refer to temperature rating chart on page 2, select temperature setting required and add this number to base catalog number. Example: Vertical DETECT-A-FIRE set to close at 225F. 12427121.000-225 Type Temperature Setting 'This literature is provided for informational purposes only. KIDDE-FENWAL. INC. assumes no responsibility for the products suitability for a particular application. The product must be property applied to perform as described herein. If you need more information on this product, or if you have a question, contact KIDDE-FENWAL, INC., Ashland, MA 01721. (508) 881-2000. WAL KIDDE-FENWAL INC. 400 MAIN STREET ASHLAND, MA 01721 (508) 881-2000 FAX: (508) 881-8920 FEM httprllwwwienwalcontrols.com 12.01.5 8198 01992 Kidde-Fenwal. Inc. Printed in U.S A. CP CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7165-1076:119 Page 1 of I CATEGORY: Control Unit (Non High-Rise) LISTEE: Kidde-Fenwal, Inc., 400 Main Street, Ashland MA 01721-2150 Contact: Terrill Garland (508) 881-2000 FAX (508) 881-1773 DESIGN: Models "2320" and "Scorpio" local fire alarm control units. Noncoded, automatic, manual, water flow, and sprinkler supervisory services. Refer to listee's data sheet for detailed product description and operational considerations. Model Part Number Description 2320 30-232000-101 Control Unit w/I20VAC Transformer 2320 30-232000-103 Control Unit w/240VAC Transformer 2320 30-232000-011 Upgrade/Retrofit Kit *2320 30-232001-001 Front Panel w/cutout for audible *2320 30-232001-002 Front Panel w/o cutout for audible Scorpio 84-232000-012 Upgrade/Retrofit Kit Scorpio 84-232000-102 Control Unit w/I20VAC Transformer Scorpio 84-232000-104 Control Unit w/240VAC Transformer *Scorpio 84-232003-001 Front Panel w/cutout for audible *Scorpio 84-232003-002 Front Panel w/o cutout for audible 06-119520-020 12 VDC, 1.2 Ah Lead Acid Battery INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating, and UL label. APPROVAL: Listed as fire alarm control units for use with separately listed compatible initiating and indicating devices.. Refer to manufacturer's Installation Manual for details. These control units do not generate a temporal pattern signal. If the distinctive three-pulse Temporal Pattern Fire Alarm Evacuation Signal (for total evacuation) in accordance with NFPA 72, 1999 Edition is required, the control units must be used with appliances that can generate the temporal pattern signal *Rev. 10-14-2004 This listing is based upon technical data submitted by the applicant CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or i"... I recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources. Date Issued: MAY 4, 2005 Listing Expires June 30, 2006 Authorized By: DIANE K. AREND, Senior Deputy 0 Program Manager CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE S LISTING No. 7150-1076:147 Page 1 of I CATEGORY: Boxes/Pull Stations LISTEE: Kidde-Fenwal, Inc., 400 Main Street, Ashland, MA 01721 Contact: Terrill Garland (508) 881-2000 *FA)( (508) 881-1773 DESIGN: Models BI and BI 1, 30-195000-002 and 30-195000-004 key lock, push bar, noncoded manual pull stations; Models 30-195000-001 and 30-195000-003 key lock, no push bar, noncoded manual pull stations. Suitable for outdoor use when installed with Model SGB- 32C back box. Refer to listee's data sheet for additional detailed product description and operational considerations. RATING: 30VDC INSTALLATION: In accordance with listee's printed installation, applicable codes & ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating and UL label. 0 APPROVAL: Listed as manual pull stations for use with separately listed and compatible fire alarm control units. XLF: 7150-1408:107 *Rev. 06-21-2003 This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or .. I recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources. Date Issued: MAY 41 2005 Listing Expires June 30, 2006 Authorized By: DIANE K. AREND, Senior Deputy Program Manager 0 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7300-1076:120 Page 1 of I CATEGORY: Misc. Devices/Control Unit Accessories LISTEE: Kidde-Fenwal, Inc., 400 Main Street, Ashland MA 01721-2150 Contact: Terrill Garland (508) 881-2000 *FA)( (508) 881-1773 DESIGN: Models PIN 30-232001-001 front panel wlcutout for audible and PIN 30-232001-002 front panel w/o cutout for audible. These units have a manual release switch and abort switch. Models 878752-011-02, 30-193000-001/-002 abort stations. Models 296105, 30-193000-003 back boxes. Models 30-322003-003, 84-322003-003 Remote Display Unit Backbox. Refer to listee's data sheet for additional detailed product description and operational considerations. INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. For indoor use only. MARKING: Listee's name, model number, and UL label. APPROVAL: Models 30-232001-001 and 30-232001-002 are listed as control unit accessories when used in conjunction with listees' separately listed fire alarm control units. Models 878752-011-02, 30-193000-0011-002 abort stations and Models 296105, 30- 193000-003 back boxes are intended for use with listed releasing device control units. Rev. 06-21-2003 BH .... This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or -' recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources. Date Issued: MAY 4, 2005 Listing Expires June 30, 2006 Authorized By: DIANE K. AREND, Senior Deputy Program Manager 0 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE C LISTING No. 7135-0785:118 Page 1 of 1 CATEGORY: Audible Devices LISTEE: Wheelock Inc., 273 Branchport Ave., Long Branch NJ 07740 Contact: Luy Nguyen (732) 222-6880 Fax (732) 222-5607 DESIGN: Model MT-12/24, MT- I 15 and MT4-12124, and MT4-I 15 multi-tone audible devices followed by R, W, S, or X to indicate package color. Models MT-I2, MT4-12, MT-24, MT4-24 multi-tone audible/strobe signals followed by A, B. G, R orWto indicate lens color, followed by S (15 cd), H (15 cd) or M (117 cd) to indicate strobe intensity, and other suffixes to designate orientation, lens lettering and plate color. Models MT-1 I5-WH and MT4-I 15-WH multi-tone audible/visual devices (Rated 15 cd). Refer to listee's data sheet for additional detailed product description and operational considerations. RATING: Suffix -12: *8175 VDC -24: *1633 VOC -115: 120 VAC INSTALLATION: In accordance with listee's printed installation instructions, NFPA 72, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. Models MT series are surface mount and suitable for outdoor with Model lOB back box. Models S MT4 series are flush mount and suitable for outdoor with model WBB back box. MARKING: Listee's name, model number, electrical/candela rating and UL label. APPROVAL: Listed as audible and audible/visual signaling devices for use with separately listed electrically compatible fire alarm control units. Not suitable for the hearing impaired application. These appliances can produce a distinctive three-pulse Temporal Pattern Fire Alarm Evacuation Signal (for total evacuation) in accordance with NFPA 72, 1999 Edition. Refer to manufacturer's Installation Manual for details. *Rev. 12-22-2002KK This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources. Date Issued: MAY 21, 2005 Listing Expires June 30, 2006 Authorized By: DIANE K. AREND, Senior Deputy Program Manager 40