Loading...
HomeMy WebLinkAbout6010 HIDDEN VALLEY RD; 120; FPC2019-0241; Permit(City of PERMIT REPORT Carlsbad CARLSBAD, CA 92011-4219 Work Class: Fire Sprinklers. Track #: Lot #: Project #: Plan #: Construction Type: Orig. Plan Check #: Plan Check #: Permit No: FPC2019-0241 Status: Closed - Finaled Applied: 10/17/2019 Issued: 10/28/2019 Finaled Close Out: 08/12/2021 Inspector: Final Inspection: Print Date: 10/14/2021 Job Address: 6010 HIDDEN VALLEY RD, # 120, Permit Type: FIRE-Construction Commercial Parcel #: 2120406800 Valuation: $158,434.56 Occupancy Group: #of Dwelling Units: Bedrooms: Bathrooms: Project Title: Description: WESTERN DERMATOLOGY -SPRINKLER TI (33 HEADS) FEE AMOUNT FIRE NFPA 13 or 13R System 7 - 100 heads $553.00 Total Fees: $553.00 Total Payments To Date: 1 $553.00 Balance Due: $0.00 Fire Department Page 1 of 1 1635 Faraday Avenue, Carlsbad CA 92008-7314 1 760-602-46651 760-602-8561 f I www.carlsbadca.gov tqpo Fire Protection Products F I %_- Worldwide Contacts www.tyco-fire.com I Series TYFRB - 28,42,56, and 80 K-Factor Upright, Pendent, and Recessed Pendent Sprinklers Quick Response, Standard Coverage General Description The TYCO Series TY-FRB, 2.8, 4.2, 5.6, and 8.0 K-factor, Upright, Pendent, and Recessed Pendent Sprinklers described in this data sheet are quick response, standard coverage, deco- rative 3 mm glass bulb-type spray sprinklers designed for use in light or ordinary hazard, commercial occupan- cies such as banks, hotels, and shop- ping malls. The recessed version of the Series TY-FRB Pendent Sprinkler, where applicable, is intended for use in areas with a finished ceiling. This recessed pendent sprinkler uses one of the following: A two-piece Style 10 (1/2 inch NPT) or Style 40 (3/4 inch NPT) Recessed Escutcheon with 1/2 inch (12,7 mm) of recessed adjustment or up to 3/4 inch (19,1 mm) of total adjustment from the flush pendent position, or a A two-piece Style 20 (1/2 inch NPT) or Style 30 (3/4 inch NPT) Recessed Escutcheon with 1/4 inch (6,4 mm) of recessed adjustment or up to 1/2 inch (12,7 mm) of total adjustment from the flush pendent position. The adjustment provided by the Recessed Escutcheon reduces the accuracy to which the fixed pipe drops to the sprinklers must be cut. Corrosion-resistant coatings, where applicable, are utilized to extend the life of copper alloy sprinklers beyond that which would otherwise be obtained IMPORTANT Always refer to Technical Data Sheet TFP700 for the "INSTALLER WARNING" that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and installation can permanently damage a sprinkler system or its compo- nents and cause the sprinkler to fail to operate in a fire situation or cause it to operate prematurely. Page 1 of 10 when exposed to corrosive atmo- spheres. Although corrosion-resistant coated sprinklers have passed the standard corrosion tests of the appli- cable approval agencies, the testing is not representative of all possible cor- rosive atmospheres. Consequently, it is recommended that the end user be consulted with respect to the suit- ability of these coatings for any given corrosive environment. The effects of ambient temperature, concentration of chemicals, and gas/chemical velocity, should be considered, as a minimum, along with the corrosive nature of the chemical to which the sprinklers will be exposed. An intermediate level of the Series TY-FRB Pendent Sprinklers is detailed in Technical Data Sheet TFP356, and Sprinkler Guards are detailed in Tech- nical Data Sheet TFP780. NOTICE The Series TY-FRB, 2.8, 4.2, 5.6, and 8.0 K-factor, Upright, Pendent, and Recessed Pendent Sprinklers described herein must be installed and maintained in compliance with this document and with the applica- ble standards of the National Fire Pro- tection Association, in addition to the standards of any authorities having jurisdiction. Failure to do so may impair the performance of these devices. The owner is responsible for maintain- ing their fire protection system and devices in proper operating condition. The installing contractor or sprinkler manufacturer should be contacted with any questions. NOVEMBER 2015 Sprinkler Identification Number (SIN) TY1131 - Upright 2.8K, 1/2" NPT TY1231 - Pendent 2.8K, 1/2 NPT TY2131 - Upright 4.2K, 1/2" NPT 1Y2231 - Pendent 4.2K, 1/2" NPT TY3131 - Upright 5.6K, 1/2" NPT .TY3231 - Pendent 5.6K, 1/2"NPT TY4131 - Upright 8.0K, 3/4" NPT TY4231 - Pendent 8.0K, 3/4" NPT TY4831 - Upright 8.0K, 1/2" NPT TY4931 - Pendent 8.0K, 1/2 NPT TFPI7I - 2-7/8" (73,0 mm) DIA. -i 2-7/8" (73,0 mm) DIA. RECESSED PENDENT CROSS SECTION TFPI7I Page 2 of 10 * Temperature rating ** Pipe thread connections per is indicated on ISO 7-1 can be provided on Deflector. special request. 1 - Frame 3 - Sealing 5 - Compression 2 - Button Assembly Screw 4 - Bulb 6 - Deflector* 7 - Bushing ESCUTCHEON PLATE SEATING SURFACE 7/16" H (11,1 mm) /W f 2-1/4 MAKE-IN NOMINAL (57,2 mm) I 2-3/16 1-9/16" I (39,7 mm) I (55,6 mm) 1/2" NPT** I WRENCH STYLE 10or20 FLATS RECESSED UPRIGHT PENDENT ESCUTCHEON CROSS SECTION 2-7/8" (73,0 mm) DIA. RECESSED PENDENT FIGURE 1 QUICK RESPONSE SERIES TV-FRB UPRIGHT (TY1131) AND PENDENT (TY1231) SPRINKLERS 2.8 K-FACTOR, 1/2 INCH NPT * Temperature rating ** Pipe thread connections per 1 - Frame is indicated on ISO 7-1 can be provided on ESCUTCHEON 2 - Button Deflector. special request. PLATE SEATING SURFACE 7/16' ____________________________________ I(1 • 1,1 mm) 2-3/16" MAKE-IN NOMINAL 16' (55,6 mm) - (55,6 mm) (38,1 mm) I 1/2' NPT** I WRENCH STYLE 100r20 FLATS RECESSED 3 - Sealing 5 - Compression Assembly Screw 4 - Bulb 6 - Deflector* UPRIGHT PENDENT ESCUTCHEON RECESSED PENDENT CROSS SECTION FIGURE 2 QUICK RESPONSE SERIES TY-FRB UPRIGHT (TY2131) AND PENDENT (TY2231) SPRINKLERS 4.2 K-FACTOR, 1/2 INCH NPT * Temperature rating ** Pipe thread connections per is indicated on ISO 7-1 can be provided on ESCUTCHEON Deflector. special request. PLATE SEATING SURFACE I 7/16' NOMINAL 2-3/16' (11,1 mm) (55,6 mm) MAKE-IN 2-3/16" 1-1/2" (55,6 mm) I (38,1 mm) - 1 - Frame 3 - Sealing 5 - Compression 2 - Button Assembly Screw 4 - Bulb 6 - Deflector* 1/2' NPT** I WRENCH STYLE 100r20 FLATS RECESSED UPRIGHT PENDENT ESCUTCHEON FIGURE 3 QUICK RESPONSE SERIES TY-FRB UPRIGHT (TY3131) AND PENDENT (TY3231) SPRINKLERS 5.6 K-FACTOR, 112 INCH NPT 2-7/8" (73,0 mm) DIA. RECESSED PENDENT CROSS SECTION TFPI7I Page 3 of 10 * Temperature rating ** Pipe thread connections per is indicated on ISO 7-1 can be provided on Deflector, special request. 1 - Frame 3 - Sealing 5 - Compression 2 - Button Assembly Screw 4 - Bulb 6 - Deflector* ESCUTCHEON PLATE SEATING SURFACE N 1/2 _ (12,7 mm) I NOMINAL I 1 2-5/16' MAKE-IN (58,7 mm) 2-1/4 (572mm)/(3 0- ril 97 mm) 1-9/16 I ' 3/4" NPT f WRENCH STYLE 30 or 40 FLATS . RECESSED UPRIGHT PENDENT ESCUTCHEON FIGURE 4 QUICK RESPONSE SERIES TY-FRB UPRIGHT (TY4131) AND PENDENT (TY4231) SPRINKLERS 8.0 K-FACTOR, 3/4 INCH NPT - - CEILING PLATE 1 - Frame 5 - Compression SEATING SURFACE 2 - Button Screw W 7/16" 1 3 - Sealing 6 - Deflector * Assembly 4 -Bulb (11,1 mm) / 2-1/4' NOMINAL (57,2 mm) * Temperature rating is 2-3/16" 1-9/16" indicated on Deflector. (39,7 mm) I (55,6mm) MAKE-IN 5 ** Pipe thread connections 6 * per ISO 7-1 can be provided on special 1/2" NPT** I WRENCH request. FLATS UPRIGHT PENDENT CROSS SECTION FIGURE 5 QUICK RESPONSE SERIES TY-FRB UPRIGHT (TY4831) AND PENDENT (TV4931) SPRINKLERS 8.0 K-FACTOR, 1/2 INCH NPT WRENCH RECESS (END "A" USED FOR 1/2" NPT MODELS) WRENCH RECESS (END "B" USED FOR 3/4" NPT MODELS) FIGURE 6 W-TYPE 6 SPRINKLER WRENCH WRENCH RECESS PUSH WRENCH INTO ENSURE ENGAGEMENT WITH SPRINKLER WRENCHING AREA FIGURE 7 W-TYPE 7 RECESSED SPRINKLER WRENCH TFPI7I Page 4 of 10 Technical Data Approvals UL and C-UL Listed FM, LPCB, and NYC Approved Refer to Table A and B for complete approval information including corrosion- resistant status. Maximum Working Pressure Refer to Table C. Discharge Coefficient K=2.8 gpm/psi½ (40,3 1pm/bar½) K=4.2 gpm/psi½ (60,5 1pm/bar½) K=5.6 gpm/psi½ (80,6 1pm/bar½) K=8.0 gpm/psi½ (115,2 1pm/bar½) Temperature Rating Refer to Table A and B. Finishes Sprinkler: Refer to Table D. Recessed Escutcheon: Signal or Pure White, Jet Black, Chrome Plated, or Natural Brass Physical Characteristics Frame ............................Bronze Button ......................Brass/Copper Sealing Assembly.. Beryllium Nickel w/TEFLON Bulb...............................Glass Compression Screw .................Bronze Deflector ...................Copper/Bronze Bushing (K=2.8).....................Bronze Operation The glass bulb contains a fluid that expands when exposed to heat. When the rated temperature is reached, the fluid expands sufficiently to shatter the glass bulb, allowing the sprinkler to activate and water to flow. Design Criteria The TYCO Series TY-FRB, 2.8, 4.2, 5.6, and 8.0 K-factor, Upright, Pendent, and Recessed Pendent Sprinklers are intended for fire protection systems designed in accordance with the stan- dard installation rules recognized by the applicable Listing or Approval agency (such as, UL Listing is based on the requirements of NFPA 13, and FM Approval is based on the require- ments of FM's Loss Prevention Data Sheets). Only the Style 10, 20, 30, or 40 Recessed Escutcheon, as applica- ble, is to be used for recessed pendent installations. Installation The TYCO Series TY-FRB, 2.8, 4.2, 5.6, and 8.0 K-factor, Upright, Pendent, and Recessed Pendent Sprinklers must be installed in accordance with this section. General Instructions Do not install any bulb-type sprinkler if the bulb is cracked or there is a loss of liquid from the bulb. With the sprin- kler held horizontally, a small air bubble should be present. The diameter of the air bubble is approximately 1/16 inch (1,6 mm) for the 135°F (57°C) and 3/32 inch (2,4 mm) for the 286°F(141°C)tem- perature ratings. A leak-tight 1/2 inch NPT sprinkler joint should be obtained by applying a minimum to maximum torque of 7 to 14 ft-lbs. (9,5 to 19,0 Nm). A leak tight 3/4 inch NPT sprinkler joint should be obtained with a torque of 10 to 20 ft.- lbs. (13,4 to 26,8 Nm). Higher levels of torque can distort the sprinkler Inlet with consequent leakage or impairment of the sprinkler. Do not attempt to compensate for insufficient adjustment in the Escutch- eon Plate by under- or over-tightening the sprinkler. Re-adjust the position of the sprinkler fitting to suit. Series TY-FRB Upright and Pendent Sprinklers The Series TY-FRB Pendent and Upright Sprinklers must be installed in accordance with the following instructions. Step 1. Install Pendent sprinklers in the pendent position. Install upright sprin- klers in the upright position. Step 2. With pipe-thread sealant applied to the pipe threads, hand- tighten the sprinkler into the sprinkler fitting. Step 3. Tighten the sprinkler into the sprinkler fitting using only the W-Type 6 Sprinkler Wrench (Figure 6). With ref- erence to Figures 1 through 5, apply the W-Type 6 Sprinkler Wrench to the sprinkler wrench flats. Series TY-FRB Recessed Pendent Sprinklers The Series TY-FRB Recessed Pendent Sprinklers must be installed in accor- dance with the following instructions. Step A. After installing the Style 10, 20, 30, or 40 Mounting Plate, as applica- ble, over the sprinkler threads and with pipe-thread sealant applied to the pipe threads, hand-tighten the sprinkler into the sprinkler fitting. Step B. Tighten the sprinkler into the sprinkler fitting using only the W-Type 7 Recessed Sprinkler Wrench (Figure 7). With reference to Figures 1 to 4, apply the W-Type 7 Recessed Sprinkler Wrench to the sprinkler wrench flats. Step C. After ceiling installation and finishing, slide on the Style 10, 20, 30, or 40 Closure over the Series TY-FRB Sprinkler and push the Closure over the Mounting Plate until its flange comes in contact with the ceiling. TFPI7I Page 5 of 10 SPRINKLER FINISH (See Note 5) K FACTOR TYPE TEMPERATURE BULB LIQUID COLOR NATURAL BRASS I CHROME PLATED POLYESTER*** 2.8 1/2" NPT PENDENT (TY1231) and UPRIGHT (TY1131) 135°F (57°C) Orange 1,2, 3, 4 155°F (68°C) Red 175°F (79°C) Yellow 200°F (93°C) Green 286°F (141°C) Blue RECESSED PENDENT (TY1231)° Figure 8 135°F (57°C) Orange 1,2,4 155°F (68°C) Red 175°F (79°C) Yellow 200°F (93°C) Green RECESSED PENDENT (TY1231)°° Figure 9 135°F (57°C) Orange 155°F(68°C) Red 175°F (79°C) Yellow 200°F (93°C) Green 4.2 1/2" NPT PENDENT (1Y2231) and UPRIGHT (TY2131) 135°F (57°C) Orange 1, 2. 155°F (68°C) Red 175°F (79°C) Yellow 200°F (93°C) Green 286°F (141°C) Blue RECESSED PENDENT (TY2231)° Figure 10 135°F (57°C) Orange 155°F (68°C) Red 175°F (79°C) Yellow 200°F (93°C) Green RECESSED PENDENT (TY2231)** Figure 11 135°F (57°C) Orange 155°F (68°C) Red 175°F (79°C) Yellow 200°F (93°C) Green NOTES: Listed by Underwriters Laboratories. Inc., (UL) as Quick Response Sprinklers. Listed by Underwriters Laboratories. Inc., for use in Canada (C-UL) as Quick Response Sprinklers. Approved by Factory Mutual Research Corporation (FM) as Quick Response Sprinklers. Approved by the City of New York under MEA 354-01-fl. Where Polyester Coated Sprinklers are noted to be UL and C-UL Listed, the sprinklers are UL and C-UL Listed as Corrosion-Resistant Sprinklers. Installed with Style 10 (1/2" NPT) or Style 40 (3/4" NPT) 3/4" Total Adjustment Recessed Escutcheon, as applicable. Installed with Style 20 (1/2" NPT) or Style 3013/4" NPT) 1/2" Total Adjustment Recessed Escutcheon, as applicable. Frame and Deflector only. N/A: Not Available TABLE A LABORATORY LISTINGS AND APPROVALS FOR 2.8 AND 4.2 K-FACTOR SPRINKLERS TFPI7I Page 6 of 10 SPRINKLER FINISH (See Note 8) K FACTOR TYPE TEMPERATURE BULB LIQUID COLOR NATURAL BRASS I CHROME PLATED I POLYESTER*** LEAD COATED PENDENT (TY3231) and UPRIGHT (TY3131) 135°F (57°C) Orange 1,2, 3, 4, 5, 6, 7 Blue 1,2, 3, 5 155°F (68°C) Red 175°F (79°C) Yellow 200°F (93°C) Green 286°F (141°C) 5.6 1/2" NPT RECESSED PENDENT (1Y3231)* Figure 12 135°F (57°C) Orange 1,2,4,5 Blue N/A 155°F(68°C) Red 175°F (79°C) Yellow 200°F (93°C) Green 286°F (141°C) RECESSED PENDENT (TY3231)** Figure 13 135°F (57°C) Orange 1, 2, 3, 4, 5 Blue N/A 155°F (68°C) Red 175°F (79°C) Yellow 200°F (93°C) Green 286°F (141°C) 8.0 3/4" NPT PENDENT (TY4231) and UPRIGHT (TY4131) 135°F (57°C) Orange 1, 2,3,4,5,6, 7 Blue 1,2,5 155°F (68°C) Red 175°F (79°C) Yellow 200°F (93°C) Green 286°F (141°C) RECESSED PENDENT (TY4231)* Figure 14 135°F (57°C) Orange 1, 2, 5 N/A 155-F (68-C) Red 175°F (79°C) Yellow 200°F (93°C) Green 286°F (141°C) Blue RECESSED PENDENT (TY4231)** Figure 15 135°F (57°C) Orange 1, 2, 3, 5 Blue N/A 155°F (68°C) Red 175°F (79°C) Yellow 200°F (93°C) Green 286°F (141°C) 8 0 1/2" NPT PENDENT (TY4931) and UPRIGHT (TY4831) 135°F (57°C) Orange 1, 2, 4, 5, 6 Blue 1, 2, 5 155°F (68°C) Red 175°F (79°C) Yellow 200°F (93°C) Green 286°F (141°C) NOTES: Listed by Underwriters Laboratories, Inc., (UL) as Quick Response Sprinklers. Listed by Underwriters Laboratories, Inc., for use in Canada (C-UL) as Quick Response Sprinklers. Approved by Factory Mutual Research Corporation (FM) as Quick Response Sprinklers. Approved by the Loss Prevention Certification Board (LPCB Ref. No. 007k/04) as Quick Response Sprinklers. However, LPCB does not rate the thermal sensitivity of recessed sprinklers. Approved by the City of New York under MEA 354-01-E. VdS Approved (For details, contact Tyco Fire Suppression & Building Products, Enschede, Netherlands, Tat. 31-53-428-4444/Fax 31-53-428-3377.1 Approved by the Loss Prevention Certification Board (LPCB Ref. No. 094a/06) as Quick Response Sprinklers. Where Polyester Coated and Lead-Coated Sprinklers are noted to be UL and C-UL Listed, the sprinklers are UL and C-UL Listed as Corrosion-Resistant Sprinklers. Where Lead-Coated Sprinklers are noted to be FM Approved, the sprinklers are FM Approved as Corrosion-Resistant Sprinklers. Installed with Style 10(1/2" NPT) or Style 40 (3/4 NPT) 3/4 Total Adjustment Recessed Escutcheon, as applicable. Installed with Style 20 (1/2" NPT) or Style 30)3/4" NPT) 1/2" Total Adjustment Recessed Escutcheon, as applicable. Frame and Deflector only. N/A: Not Available TABLE B LABORATORY LISTINGS AND APPROVALS FOR 5.6 AND 8.0 K-FACTOR SPRINKLERS TFPI7I Page 7 of 10 SPRINKLER FINISH K TYPE NATURAL I CHROME I POLYESTER LEAD FACTOR BRASS PLATED COATED PENDENT (1Y1231) and 2.8 UPRIGHT (TY1131) 1/2" NPT 175 PSI (12,1 BAR) N/A RECESSED PENDENT (TY1231) PENDENT (TY2231) and 4.2 UPRIGHT (TY2131) 1/2" NPT 175 PSI (12,1 BAR) N/A RECESSED PENDENT (TY2231) PENDENT (TY3231) and 5.6 UPRIGHT (TY3131) 250 PSI (17,2 BAR) 1/2" NPT OR 175 PSI (12,1 BAR) RECESSED (SEE NOTE 1) PENDENT (TY3231) PENDENT (TY4231) 175 PSI 8.0 and UPRIGHT (TY4131) (12,1 BAR) 3/4" NPT 175 PSI (12,1 BAR) RECESSED N/A PENDENT (TY4231) 8.0 PENDENT( Y4931) 175 PSI 1/2" NPT and 175 PSI (12,1 BAR) (12,1 BAR) UPRIGHT (TY4831) NOTES: 1. The maximum working pressure of 250 psi (17,2 bar) only applies to the Listing by Underwriters Laboratories Inc. (UL); the Listing by Under- writers Laboratories, Inc. for use in Canada (C-UL); and, the Approval by the City of New York. TABLE C MAXIMUM WORKING PRESSURE Care and Maintenance The TYCO Series TY-FRB must be maintained and serviced in accordance with this section. Before closing a fire protection system main control valve for maintenance work on the fire protection system that it controls, obtain permission to shut down the affected fire protection systems from the proper authorities and notify all personnel who may be affected by this action. Absence of the outer piece of an escutcheon, which is used to cover a clearance hole, can delay sprinkler operation in a fire situation. Sprinklers which are found to be leaking or exhibiting visible signs of corrosion must be replaced. Automatic sprinklers must never be painted, plated, coated, or other- wise altered after leaving the factory. Modified sprinklers must be replaced. Sprinklers that have been exposed to corrosive products of combustion, but have not operated, should be replaced if they cannot be completely cleaned by wiping the sprinkler with a cloth or by brushing it with a soft bristle brush. Care must be exercised to avoid damage to the sprinklers before, during, and after installation. Sprin- klers damaged by dropping, striking, wrench twist/slippage, or the like, must be replaced. Also, replace any sprin- kler that has a cracked bulb or that has lost liquid from its bulb. (Ref. Installa- tion Section.) The owner is responsible for the inspection, testing, and maintenance of their fire protection system and devices in compliance with this document, as well as with the applicable standards of the National Fire Protection Asso- ciation (e.g., NFPA 25), in addition to the standards of any other authorities having jurisdiction. Contact the install- ing contractor or sprinkler manufac- turer regarding any questions. Automatic sprinkler systems are rec- ommended to be inspected, tested, and maintained by a qualified Inspec- tion Service in accordance with local requirements and/or national codes. Care must be exercised to avoid damage to the sprinklers -before, during, and after installation. Sprin- klers damaged by dropping, striking, wrench twist/slippage, or the like, must be replaced. Also, replace any sprin- kler that has a cracked bulb or that has lost liquid from its bulb. (Ref. Installa- tion Section). Initial and frequent visual inspections of random samples are recommended for corrosion-resistant sprinklers to verify the integrity of the corrosion-resistant material of construction. Thereafter, annual inspections per NFPA 25 should suffice. Inspections of corrosion-resistant sprinklers are recommended at close range, instead of from the floor level per NFPA. Inspection at close range can better determine the exact sprin- kler condition and the long-term integ- rity of the corrosion-resistant material, which can be affected by the corrosive conditions present. TFPI7I Page 8 of 10 2-7/8 DIA. - 5/8±1/4" (73,0 mm) 3/4" (19,1 mm) (15,9±6,4 mm) 1/4" (6,4) MOUNTING 1 / FACE OF 2-1/4" DIA. SPRINKLER PLATE (57,2 mm)?1 FITTING 1/8" / i_(3,2 mm) rli- / I MOUNTING SURFACE CLOSURE SERIES 1-5/16" (33,3 mm)j TY-FRB 13/16" (20,6 mm) FIGURE 8 SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT STYLE 10 RECESSED ESCUTCHEON 2.8 K-FACTOR, 1/2 INCH NPT 2-7/8" DIA. - 5/8±1/4" (73,0 mm) I 3/4" (19,1 mm) (15,9±6,4 mm) 2-1/4" DIA. I 1/4" (6,4 mm) I / FACE OF - (57,2 mm) MOUNTING SPRINKLER\t PLATE I FITTING 1/8" -a rH (3,2 mm) MOUNTING SURFACE SERIES 1-1/4(31,8 mm) f CLOSURE TY-FRB 3/4" (19,1 mm) FIGURE 10 SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT STYLE 10 RECESSED ESCUTCHEON 4.2 K-FACTOR, 1/2 INCH NPT - 2-7/8" DIA. - 1/2±1/8" (73,0 mm) 1/2" (12,7 mm) (12,7±3,2 mm) 2-1/4" DIA. 1/4" (6,4 mm) / FACE OF (57,2 mm) MOUNTING SPRINKLER PLATE I FITTING / 1/8" (3,2 mm) I P71 7/ I \4_ _ J MOUNTING SURFACE 1-5/16" (33,3 mm) CLOSURE SERIES TY-FRB 1-1/16" (27,0 mm) FIGURE 9 SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 20 RECESSED ESCUTCHEON 2.8 K-FACTOR, 1/2 INCH NPT 2-7/8" DIA. (73,0 mm) I 1/2±1/8" I 1/2(12,7mm) (12,7±3,2 mm) 2-1/4" DIA. 1/4" (6,4 mm) I / FACE OF T (57,2 mm) MOUNTING SPRINKLER PLATE L\?- I FITTING L(3,,2 mm) _ MOUNTING 0 SURFACE SERIES 1-1/4" (31,8 mm) CLOSURE TY-FRB 1" (25,4 mm) FIGURE 11 SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 20 RECESSED ESCUTCHEON 4.2 K-FACTOR, 1/2 INCH NPT TFP171 Page 9 of 10 2-7/8 DIA. - - 5/8±1/4" (73,0 mm) 3/4" (19,1 mm) (15,9±6,4 mm) 2-1/4" DIA. I 1/4" (6,4 mm) / FACE OF - (57,2 mm) MOUNTING SPRINKLER 1_ PLATE FITTING 1/8 (3,2 mm) \% MOUNTING I SURFACE SERIES 1-1/4" (31,8 mm)_ CLOSURE TY-FRB 3/4" (19,1 mm) FIGURE 12 SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT STYLE 10 RECESSED ESCUTCHEON 5.6 K-FACTOR, 1/2 INCH NPT 2-7/8 DIA. I (73,0 mm) 5/8±1/4' 3/4" (19,1 mm) I (15,9±6,4 mm) 2-1/4" DIA. 1/4' (6,4 mm) I - (57,2 mm) / FACE OF SPRINKLER PLATE MOUNTING FITTING 1/8' (3,2 mm) MOUNTING SURFACE CLOSURE SERIES 1-5/16" (33,3 mm)j TYFRB 13/16" (20,6 mm) FIGURE 14 SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT STYLE 40 RECESSED ESCUTCHEON 8.0 K-FACTOR, 3/4 INCH NPT 2-7/8" DIA. - - (73,0 mm) 1/2±1/8" 1/2" (12,7 mm) / 2,7±3,2 mm) 2-1/4" DIA. 1/4" (6,4 mm) FACE OF (57,2 mm) _MOUNTING I SPRINKLER PLATE FITTING 1/8" (3,2 mm) MOUNTING SURFACE SERIES 1-1/4"(31,8 mm) JCLOSURE TY-FRB 1" (25,4 mm) FIGURE 13 SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 20 RECESSED ESCUTCHEON 5.6K-FACTOR, 1/2 INCH NPT - 2-7/8" DIA. - 1/2±1/8" (73,0 mm) 1/2" (12,7 mm) (12,7+3,2 mm) 2-1/4" DIA. 1/4" (6,4 mm) FACE OF (57,2 mm) PLATE MOUNTING I SPRINKLER FITTING 1/8" __ __ II I \ MOUNTING SURFACE CLOSURE SERIES 1-5/16" (33,3 mm) TY-FRB 1-1/16" (27,0 mm) FIGURE 15 SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 30 RECESSED ESCUTCHEON 8.0 K-FACTOR, 3/4 INCH NPT I SPRINKLER FINISH 1 NATURAL BRASS - PURE WHITE POLYESTER (RAL901O)1 SIGNAL WHITE POLYESTER (RAL9003) JET BLACK POLYESTER (RAL9005)2 7 LEAD COATED TEMPERATURE RATINGS 135 135°F(57°C) 155 155°F(68°C) 175 175°F(79°C) 200 I 200°F (93°C) 286 I 286°F (141°C) 9 I CHROME PLATED NOTES: Eastern Hemisphere sales only. Available in only 2.8K. 4.2K, and 8.0K, 155F (68C) and 200F (93C); requires lead time to manufacture. TFPI7I Page 10 of 10 P/N 57- XXX- X- XXX SIN 330 2.8K UPRIGHT (1/2"NPT) TY1131 331 2.8K PENDENT (1/2"NPT) TY1231 340 4.2K UPRIGHT (1/2"NPT) TY2131 341 4.2K PENDENT (1/2"NPT) TY2231 370 5.6K UPRIGHT (1/2"NPT) TY3131 371 5.6K PENDENT (1/2"NPT) 1Y3231 390 8.0K UPRIGHT (3/4"NPT) TY4131 391 8.0K PENDENT (3/4"NPT) TY4231 360 8.0K UPRIGHT (1/2"NPT) TY4831° 361 8.0K PENDENT (1/2"NPT) TY4931° TABLED SERIES TY-FRB PENDENT AND UPRIGHT SPRINKLERS PART NUMBER SELECTION Limited Warranty For warranty terms and conditions, visit www.tyco-fire.com. Ordering Procedure Contact your local distributor for availability. When placing an order, indicate the full product name and Part Number (P/N). Sprinkler Assemblies with NPT Thread Connections Specify: Series TY-FRB (Specify SIN), (specify K-factor), (specify Pendent or Upright) Sprinkler (specify) temperature rating, (specify) finish or coating, P/N (specify from Table D) Recessed Escutcheon Specify: Style (10, 20, 30, or 40) Recessed Escutcheon with (specify*) finish, P/N (specify*) Sprinkler Wrench Specify: W-Type 6 Sprinkler Wrench, P/N 56-000-6-387 Specify: W-Type 7 Sprinkler Wrench, P/N 56-850-4-001 Refer to Technical Data Sheet TFP770 GLOBAL HEADQUARTERS 1 1400 Pennbrook Parkway, Lansdale, PA 194461 Telephone +1-215-362-0700 Victaulic® VicFlexTM Sprinkler Fittings Series AH2 and AH2-CC Braided Flexible Hoses Frc-2-6t 01 -caJd jtauIic 10.85 lii Elex" 1.0 PRODUCT DESCRIPTION Series AH2-CC Available Sizes by Component Series AH2 1/DN25 Nominal ID Braided Hose: 31; 36, 48, 60, 72/790, 915, 1220, 1525, 1830 mm. Note: length includes adapter nipple and 5.757140 mm straight reducer. Series AH2-CC 17DN25 Nominal ID Braided Hose: 31, 36, 48, 60, 72/790, 915, 1220, 1525, 1830 mm. Note: length includes captured coupling and 5.757140 mm straight reducer. Sprinkler Reducers: Sprinkler Connections: ½ and %715 and 20 mm Straight Lengths: 5.75, 9, 13/140, 230, 330 mm 900 Elbows: Short (typically used with concealed sprinklers) Long (typically used with recessed pendent sprinklers) Low Profile Short (for use with Style ABS, AB11, AB12, ABBA and ABMM Bracket) Low Profile Long (for use with Style AB5, AB11, AB12, ABBA and ABMM Bracket) Inlet Connections: 1'725 mm Grooved IGS 1/25mm NPT or BSPT adapter nipples for attaching to pipe and fittings outlined in NFPA standards. 3/4'720mm NPT or BSPT adapter nipples available for VdS. 11/47 32 mm BSPT adapter nipples available for LPCB. ALWAYS REFER TO ANY NOTIFICATIONS AT THE END OF THIS DOCUMENT REGARDING PRODUCT INSTALLATION, MAINTENANCE OR SUPPORT. System No. Location Spec Section Paragraph Submitted By Date . Approved Date I victaulic.com 10.85 5839 Rev AG updated 07/2019 © 2019 Victaulic company. All rights reserved. 1 _______ victaulic.com I 1.0 PRODUCT DESCRIPTION (Continued) Brackets: Style AB1 for suspended and hard-lid ceilings and sidewalls, allows installation before most ceiling tiles in place Style AB2 for suspended and hard-lid ceilings and sidewalls, allows for vertical sprinkler adjustment, and installation before most ceiling tiles in place Style A133 for surface mount applications, wood, metal and block walls, or ceilings Style A134 for hard-lid ceilings with hat furring channel grid systems, allows for vertical sprinkler adjustment Style A135 for hard-lid ceilings and sidewalls, allows for vertical sprinkler adjustment Style AB7 for suspended and hard-lid ceilings Style A137 Adjustable for suspended and hard-lid ceilings Style AB8 for hard-lid ceilings with CD 60/27 profile metal studs (regionally available) Style AB9 for hard-lid ceilings with hat furring channel grid systems Style A1310 for Armstrong® TechZoneTM ceilings Style AB11 for lay-in panel suspended I-grid ceilings or drywall suspended t-grid ceilings, allows for low profile installations (use only with 900 low profile elbows) Style AB12 for suspended and hard-lid ceilings, allows for vertical sprinkler adjustment, and allows for low profile installation down to 47100mm. Style ABBA bracket for suspended, exposed, and hard-lid ceilings Style ABMM bracket for surface mount and stand off-mount applications, wood, metal and block walls, or ceilings and hard-lid ceilings Maximum Working Temperature 225°F/107°C Maximum Working Pressure 200 psi/1375 kPa (FM Approval) 175 psi/1206 kPa (cULus Listed) 1600 kPa/232 psi (VdS/LPCB Approved) 1.4 MPa (CCCf Approved) Connections To adapter nipple (inlet) via 1/25.4mm Grooved IGS 1725.4 mm NPT or BSPT male thread 3/4720 mm BSPT male thread (VdS only) 11/4732 mm BSPT male thread (LPCB only) To sprinkler head (outlet) via ½ or 3/4715 mm or 20 mm Minimum Bend Radius 77178 mm (FM/CCCf Approval) 2/51 mm (cULus Listed) 3/76.2mm (VdS/LPCB Approved) Maximum Allowable Sprinkler K-Factors FM (½'/lSmm reducer) K5.6/8,1 (SI.), (3/4 /20mm reducer) K14.0/20,2 (SI.) cULus (1/2'715 mm reducer) K8.0/11,5 (SI.), (3/4720 mm reducer) K14.0/20,2 (SI.) VdS/LPCB (1/2715mm reducer) K5.6/8,1 (SI.), (3%/20mm reducer) K8.0/11,5 (SI.) 10.85 5839 Rev AG Updated 07/2019 © 2019 Victaulic company. All rights reserved. victaulic.com 2 JtauIic' victaulic.com 2.0 CERTIFICATION/LISTINGS NOTE The VjcF/ex Series AH2 Hose has been tested and evaluated by Spears® for acceptable use with Spears® CPVC Products and is therefore covered under the Spears® FlameGaurd® Installer Protection Plan. 3.0 SPECIFICATIONS - MATERIAL Series AH2 Flexible Hose: 300-series Stainless Steel Collar/Weld Fitting: 300-series Stainless Steel Gasket Seal: Victaulic EPDM Isolation Ring: Nylon Nut and Nipple: Carbon Steel, Zinc Plated Reducer ('/2/15 mm or 3/4720 mm): Carbon Steel, Zinc-Plated Low Profile Elbows: Ductile Iron, Zinc-Plated Brackets: Carbon Steel, Zinc-Plated Series AH2-CC Flexible Hose: 300-series Stainless Steel Collar/Weld Fitting: 300-series Stainless Steel Gasket Seal: Victaulic EPDM Isolation Ring: Nylon Coupling Retainer Ring: Polyethelene Nut and Nipple: Carbon Steel, Zinc Plated Reducer (1/2 I15 mm or /4?2O mm): Carbon Steel, Zinc-Plated Housing: Ductile iron conforming to ASTM A 536, Grade 65-45-12. Ductile iron conforming to ASTM A 395, Grade 65-45-15, is available upon special request. Coupling Housing Coating: Orange enamel (North America, Asia Pacific). Red enamel (Europe). Hot dipped galvanized. Gasket:' Grade "E" EPDM (Type A) FireLock EZ products have been Listed by Underwriters Laboratories Inc., Underwriters Laboratories of Canada Limited, and Approved by Factory Mutual Research for wet and dry (oil free air) sprinkler services within the rated working pressure. I Services listed are General Service Guidelines only. It should be noted that there are services for which these gaskets are not compatible. Reference should always be made to the latest Victaulic Gasket Selection Guide for specific gasket service guidelines and for a listing of services which are not compatible. Bolts/Nut: Zinc electroplated carbon steel, trackhead meeting the physical and chemical requirements of ASTM A 449 and physical requirements of ASTM A 183. Linkage: CrMo Alloy Steel zinc electroplated per ASTM B633 Zn/Fe 5, Type Ill Finish 10.85 5839 Rev AG updated 07/2019 © 2019 Victaulic company. All rights reserved. victaulic.com 3 '.jtaui,c' victaulic.com 4.0 DIMENSIONS Product Details - Series AH2 Braided Hose so Sol IIIII Hose Length Dimensions Hose Length inches mm A inches mm B inches mm 31/790 25.3/641 31/790 36/915 31.3/794 36/915 48/1219 42.3/1073 - 48/1220 60/1525 54.3/1378 60/1525 72/1830 66.3/1683 72/1830 Series AH2-CC Braided Hose 00 I! 1.1 !IiIII :Iiriiiiiiiiiiiiiiiiiiiiiii:II Hose Length inches mm A inches mm B inches mm 31/790 24.5/622 29.8/757 36/915 29.5/749 34.8/884 48/1219 41.5/1054 46.8/1189 60/1525 53.5/1359 58.8/1494 72/1830 65.5/1664 70.8/1798 Item Description 1 Flexible Hose - 2 Isolation Ring 3 Gasket 4 Nut 5 - Adapter Nipple 6 Braid 7 Collar/Weld Fitting 8 Sleeve Item Description 1 Flexible Hose 2 Isolation Ring 3 Gasket 4 Nut 5 Captured Coupj 6 1 Braid 7 Collar/Weld Fitting 8 Sleeve 10.85 5839 Rev AG Updated 07/2019 © 2019 Victaulic Company. All rights reserved. victaulic.com 4 J3tauIic' victaulic.com 4.0 DIMENSIONS (Continued) Standard Reducer lilUUl'! 'l1llh'1ll1llfflu1llll"1'iJ1 5.75/140 mm straight reducer Optional Reducers 9.0/229 mm straight reducer III DH011ll 13.0/330 mm straight reducer 2.62/ 66.5 mm 4.83/ 122.7 mm Short 90° elbow reducer Long 90° elbow reducer NOTE The Short 90° elbow reducer is typically used with concealed sprinklers while the longer 90 elbow is typically used in the installation of recessed pendent sprinklers. FM/VdS Approved only. Low Profile I 116mm 1.47 36 mm 1.4/ 36mm Short 90° elbow reducer Long 90° elbow reducer NOTE Style AB 11: When low profiles elbows are used with the Style AB 11 bracket, the Low Profile Short Elbow is typically used with concealed sprinklers while the Low Profile Long Elbow is typically used in the installation of recessed pendent sprinklers. 10.85 5839 Rev AG Updated 07/2019 © 2019 Victaulic Company. All rights reserved. victaulic.com 5 OF \1:taUIic victaulic.com 4.1 DIMENSIONS VicFlex Brackets Style AB1 Suspended Ceilings Hard-Lid Ceilings (FM Only) Item Description 1 24'/610mm0r48/1219mmSquareBar 2 Patented Center Bracket End Bracket NOTE Both sizes FM/VdS/LPCB Approved cULus listed Style AB2 Suspended Ceilings Hard-Lid Ceilings Item Description 1 24/610mmor48/1219mm Square Bar 2 Patented Vertically Adjustable Center Bracket 3' End Bracket - NOTE Both sizes FM/VdS/LPCB Approved, cULus listed Style AB3 Surface Mount Applications FM/LPCB Approved 10.85 5839 Rev AG Updated 07/2019 © 2019 Victaulic Company. All rights reserved. victaulic.com J'taUIic' Style AB5 Hard-Lid Ceilings Item Description 1 24"/610thm0r48'/1219mm Square Bar 2 Patented Vertically Adjustable Center Bracket 3 End Bracket NOTE Both sizes FM/VdS/LPCB Approved, cuLus listed. victaulic.com 4.2 DIMENSIONS VicFlex Brackets Style AB4 Hard-Lid Ceilings with Hat furring channel grid system Item Description 1 24"/610mm0r48"/1219mm Square Bar 2 Patented Vertically Adjustable Center Bracket 3 End Bracket for Hat Furring Channel NOTE Both sizes FM/VdS/LPCB Approved, cuLus listed. Style AB7 Suspended Ceilings Hard-Lid Ceilings Item Description 1 24'7610 mm or 48'71219 mm Square Bar 2 Patented 1-Bee2 Center Bracket 3 End Bracket NOTE Both sizes FM/VdS/LPCB Approved. Style AB7 Adjustable Suspended Ceilings Hard-Lid Ceilings Item Description 1 700 mm or 1400 mm Square Bar 2 Patented 1-Bee2 Center Bracket 3 End Bracket (adjustable) NOTE Both sizes FM/VdS/LPCB Approved. 10.85 5839 Rev AG updated 07/2019 © 209 Victaulic Company. All rights reserved. uitfiiIir mm 7 jZtauiic' victaulic.com 4.3 DIMENSIONS VicFlex Brackets Style AB8 Hard-Lid Ceilings Item Description 1 700 mm or 1400mm Square Bar 2 Patented Vertically Adjustable Center Bracket 3 End Bracket NOTE Both sizes FM/VdS/LPCB Approved. Style AB1O Suspended ceilings Armstrong® TechZone Item Description 6"/152 mm Square Bar 2 Patented I -Bee2l Center Bracket 3 - End Bracket NOTE FM/VdS/LPCB Approved, cULus listed. Style AB11 Suspended ceilings Hard-Lid ceilings Item Description 1 247610 mm 0r48'/1219mm Square Bar 2 Patented 1-Bee2° Center Bracket 3 End Bracket NOTE FM/VdS Approved, zULus listed. Style AB12 Suspended ceilings Hard-Lid ceilings Item Description 1 Style AB1 2 Bracket Body I 2 #2 Square Drive Set Screw NOTE FM/VdS Approved. 10.85 5839 Rev AG Updated 07/2019 © 2019 Victaulic Company. All rights reserved. - -, 4::tuiic' victaulic.com 4.3 DIMENSIONS (CONTINUED) VicFlex Brackets Style ABBA Floor-above mount Cantilever mount Temporary mount in exposed ceilings Item Description 1 Style ABBA Mounting Plate 2 Style ABBA Square Bar Cap Screw, Serated Flange, M6 x x 20, T25 Torx Drive Recessed 4 Style ABMM Bracket Body Cap Screw, Serated Flange, M6 x 1 x 15.24, T25 Torx Drive Recessed Style ABMM Surface mount Stand-off mount Item Description 1 Style ABMM Bracket Body 2 Cap Screw, Serated Flange, M6 x x 15.24, T25 Torx Drive Recessed 10.85 5839 Rev AG Updated 07/2019 © 2019 Victaulic Company. All rights reserved. victaulic.com 9 JtauIic' victaulic.com 4.4 DIMENSIONS Clearances Series AH2 Braided Hose and Style AB1 Bracket A tceiling See Chart 2W/60 mm 211s/68 mm max. hole max. hole Style "N 2/Sl mm 2W/hO mm 4.47 113mm mm. hole mm. hole 1.7/43 mm Typical ceiling grid L Finished See note J ceiling face 24/61Ommor V27 V38 48"/I 2t9 mm on Pendent Center Hose Clearance Chart Straight Reducer Long Elbow Short Elbow V2707 V3802 V2707 V3802 3/4" ½" 3/4" ½" V2707 V3802 V2707 V3802 Max Recess Max Recess Max Recess Max Recess 3/4"Max Recess ½' Max Recess 3/4" Max Recess ½" Max Recess inches inches inches inches inches inches inches inches mm mm mm mm mm . mm mm mm "R" Minimum 2.0 3.0 7.0 Bend Radius 50 80 175 - "A" Minimum Required 8.6 10.1 9.6 11.1 13.6 15.1 5.8 5.8 Installation 218 269 244 281 345 383 147 147 Space NOTE Variations of ceiling grids, sprinkler heads, brackets, and hoses are permitted but may result in clearance differences from the figures above. 10.85 5839 Rev AG Updated 07/2019 © 2019 Victaulic Company. All rights reserved. victaulic.com 10 j4BtauIec' victaulic.com 4.5 DIMENSIONS Clearances Series AH2 Braided Hose and Style AB2 Bracket 2W/60 mm 2W/60 mm max. hole max. hole 275 mm 2/5l mm mix. hole mix, hole UL Hose clearance chart Straight Reducer V2707 V3802 V2709 V2707 V3802 V2709 V2707 V3802 V2709 3/4'I2Omm ½'ll3mm Wl2Omm 3/4"120mm ½"ll3mm 3/4'120mm 3/4'120mm ½'I13mm Wl20mm Max Recess" Max Recess Sidewall Max Recess Max Recess Sidewall Max Recess Max Recess Sidewall inches inches inches inches inches inches inches inches inches mm mm mm mm mm mm mm mm mm "R" Minimum 2.0 ' ' 3.0 . 7.0 Bend Radius , 50 80 . 175 "A" Minimum Required 6.2 7.6 6.1 7.2 8.6 7.1 11.2 12.6 11.1 Installation 158 193 155 183 218 180 285 320 282 Space Hose clearance chart Long Elbow Short Elbow V2707 V2709 V3802 3/4"120mm 3/4'120mm 1/2'113mm Max Recess Sidewall Max Recess inches inches inches mm mm mm "R" Minimum .. - Bend Radius "A" Minimum Required 3.3 3.6 3.3 Installation 84 91 84 Space NOTE Variations of ceiling grids, sprinkler heads, brackets, and hoses are permitted but may result in clearance differences from the figures above. 10.85 5839 Rev AG Updated 07/2019 © 2019 Victaulic Company. All rights reserved. victaulic.cnm 11 13t;IIuIic' 21A - /60 mm 2'llr'/68 mm Irt max. hole man, hole 2'/51 mm 2W/60 mm mix, hole mix, hole tW/l59mm Typical 'S_ Typical finished 1' ceiling tile I ceiling face J Typical 16-/406 mm - h/23 mm Typical V27 V38 24/610 mm on Center ceilino mid Pendent See victaulic.com 4.6 DIMENSIONS Clearances Series AH2 Braided Hose and Style AB4 Bracket Hose Clearance Chart Straight Reducer Long Elbow Short Elbow I V2707 V3802 V2707 V3802 3/4"½' 3/," 1/2" V2707 V3802 V2707 V3802 Max Recess Max Recess Max Recess Max Recess 3/4" Max Recess ½" Max Recess 3/4" Max Recess 1/2 Recess inches inches , inches inches inches inches inches inches mm mm mm mm mm mm mm mm "R" Minimum 2.0 2.0 3.0 ' 3.0 7.0 7.0 Bend Radius 50 50 80 80 175 175 - "A" Minimum Required 8.8 10.2 9.8 11.2 13.8 15.2 8.0 5.9 Installation 224 259 249 285 351 386 203 150 Space NOTE Variations of ceiling grids, sprinkler heads, brackets, and hoses are permitted but may result in clearance differences from the figures above. 10.85 5839 Rev AG Updated 07/2019 © 2019 Victaulic Company. All rights reserved, victaulic.com 12 victaulic.com Ij 4.7 DIMENSIONS Clearances Series AH2 Braided Hose and Style AB5 Bracket A See Chart - 2W/65 mm 2146768 mm 2W/60 mm 2.37 max. hole mar. hole max. hole mm 2751 mm 2W/SO mm 2751 mm - min. hole min. hole min. hole 3 67 92 mm 41, nM,,l e d ig ceiling fac 4L V27 V38 V27 Pendent Sidewall Hose Clearance Chart Straight Reducer "V2707 V3802 V2709 V2707 V3802 V2709 V2707 V3802 V2709 3/4"120mm ½ll3mm 3/4'120mm 3/4 120mm ½'ll3mm 3/4 120mm ~120mm 1/2'113mm 3/4'120mm Max Recess Max Recess Sidewall Max Recess Max Recess Sidewall Max Recess Max Recess Sidewall inches inches inches inches inches inches inches inches inches mm mm mm mm mm mm mm mm mm 'R"Minimum 2.0 3.0 7.0 Bend Radius 50 80 175 "A" Minimum Required 6.0 7.7 6.1 7.0 8.7 7.1 11.0 12.7 11.1 Installation 158 196 155 178 221 180 279 323 282 Space Hose Clearance Chart Low-Profile Long Elbow Long Elbow Short Elbow V2707 V3802 V2709 V3802 V3802 3/4 120mm 1/2" 113 3/4 .'l ½'ll3mm Y2ll3mm Max Recess Max Recess Sidewall Max Recess Max Recess inches inches inches inches inches mm mm mm mm mm "R" Minimum Bend Radius "A" Minimum Required 3.5 4.9 3.6 2.9 3.3 Installation 89 124 91 74 84 Space NOTE Variations of ceiling grids, sprinkler heads, brackets, and hoses are permitted but may result in clearance differences from the figures above. Stud C/C 10.85 5839 Rev AG Updated 07/2019 © 2019 Victautic company. All rights reserved. victaulic.com 13 ___________ victaulic.com 4.8 DIMENSIONS Clearances Series AH2 Braided Hose and Style AB11 Bracket (LOW PROFILE SOLUTION) ________ 2W/60 mm 291/768 mm max. hole max. hole Style AB Bracket 3.07 Style AB I I I Assembly JL1O c 2'/51 mm 2W/60 mm min. hole mm. hole 4 E 4 4 See Chart ______________ 76mm If I) 1.7743 '4 Finished ceilrg grid Typica! Typical 5/a/lS.9•J min ceilir, See Note 247610aft or —ceiling face ceiling tile V27 V38 4871219 mm on center Pendent Hose Clearance Chart Low-Profile Low-Profile Long Elbow Short Elbow V2707 V3802 3/4"120mm Wl13mm Max Recess" Max Recess inches inches mm mm 'A" Minimum Required 4.0 3.9 Installation 102 99 Space NOTE Variations of ceiling grids, sprinkler heads, brackets, and hoses are permitted but may result in clearance differences from the figures above. Al 10.85 5839 Rev AG Updated 07/2019 © 2019 Victaulic Company. All rights reserved. victaulic.com 14 JtUIiC' victaulic.com 4.9 DIMENSIONS Clearances Style AB12 and ABBA Bracket Suspended Ceiling Grid with Recessed Sprinkler with Low Profile Short Elbow Suspended Ceiling Grid with Recessed Sprinkler and Straight 5.757140mm Reducer Sqr Nnin& )4./315 Iyp4caI Lesiing V207 4"I19 n,** MAX. RECESS V2707 Y"/12.7 n**n MAX. RECESS Low Profile Low Profile Standard Standard Standard Dimension Short Elbow Long Elbow Short Elbow Long Elbow Straight Reducer 3/4 I19mm 3/4 /19mm 3/4719mm 3/4719mm 3/4"/l9 mm Recessed* Concealed Recessed Concealed Recessed Concealed Recessed Concealed Recessed Concealed inches inches inches inches inches inches inches inches inches inches mm mm mm mm mm mm mm mm mm mm A Minimum Required 4.0 5.5. 5.6 7.2 5.9 7.5 7.7 9.3 15.0 116.6 Installation Space 101.6 139.7 142.2 182.9 149.9 190.5 195.6 236.2 381.0 421.6 Distance from Top of B Typical Ceiling Tile to 05 20 15 15 15 15 30 30 30 30 Bottom of Gate 12.7 50.8 38.1 38.1 38.1 38.1 76.2 76.2 76.2 76.2 * Adiustability will be limited Style ABMM Bracket Stand-off Dimensions I 2.22/ S6 mm 337 1L F2., 100mm ii 75 mm IL 39.9417 5 100mm 7mm 10.85 5839 Rev AG updated 07/2019 © 2019 Victaulic company. All rights reserved. 15 J1r;:1t9uIic. victaulic.com 4.10 DIMENSIONS Clearances Style AB3 and ABMM Bracket Surface Mount Application with Recessed Sprinkler 2/51 mm mm. hole Hose Clearances inches inches inches inches inches inches inches inches I inches I inches Dimension mm mm mm mm mm mm mm mm mm mm Wall Thickness 2 4 6 8 10 2 4 6 8 10 'A' 50 100 150 200 250 50 100 150 200 250 Outlet Length 5.75 9 13 5.75 9 13 9 13 13 13 5.75 9 13 5.75 9 13 9 13 13 13 "B 146.1 228.6 330.2 146.1 228.6 330.2 228.6 330.2 3302 330.2 146.1 228.6 330.2 146.1 228.6:330.2 228.6 330.2 330.2 330.2 Hose Clearance 11.6 14.8 18.8 9.6 1 12.8 16.8 10.8 14.8 12.8 10.8 12.6 15.8 19.8 10.6 13.8 17.8 11.8 15.8 13.8 11.8 294 376 478 243 1325 427 275 376 325 275 319 402 503 268 351 452 300 402 351 300 Bend Radius 7 1 8 175 . 200 NOTE Variations of ceiling grids, sprinkler heads, brackets, and hoses are permitted but may result in clearance differences from the figures above. 10.85 5839 Rev AG Updated 07/2019 © 2019 Victaulic Company. All rights reserved. victulic.com 16 J3t1uIic victaulic.com 5.0 PERFORMANCE - FRICTION LOSS DATA Alls Series AH2 and AH2-CC Braided Hoses with Straight 5.75/140 mm Reducers LISTED Style AB1, AB2, AB4, AB5 and AB10 Brackets inches/mm inches/mm/type Equivalent Length of I"/33.7 mm Sch. 40 Pipe (C=120) feet/meters Maximum Number of 0 Bends at 2'751 mm 90 Bend Radius 31/790 w'/15/Straight - 16/4.9 4 1/4"/20/Straight 17/5.2 1 36/915 ½/iS/Straight 21/6.4 5 1/4"/20/Straight 23/7.0 5 48/ 12 20 1/2"/15/Straight 32/9.8 8 3%/20/Straight 37/11.3 8 60/1525 ½/iS/Straight j 46/14.0 10 1/4 /20/Straight j 46/14.0 10 - 72/1830 j 1/2715/Straight .j 55/16.8 12 34720/Straight j 53/16.2 12 Series AH2 and AH2-CC Braided Hose with 900 Low Profile Elbows LISTED Style AB11 VicFlex Bracket Maximum Equivalent Length Number of of 133.7 mm 90 Bends at 2'751 mm Sch. 40 Pipe Bend Radius inches/mm inches/mm - feet/meters 31/790 ½"/15 24/7.3 4 /4720 - 24/7.3 4 36/915 1/211/15 26/7.9 5 4/20 28/8.5 5 48/1220 1/2715 43/13.1 8 3/4 /20 42/12.8 8 60/1525 1/2 /15 49/14.9 10 4720 50/15.2 10 72/1830 ½'/15 65/19.8 12 3/4'/20 . -- 63/19.2 12 10.85 5839 Rev AG Updated 07/2019 © 2019 Victaulic Company. All rights reserved. victaulic.com 17 j:tauIic rd victaulic.com 5.0 PERFORMANCE - FRICTION LOSS DATA (CONTINUED) Series AH2 and AH2-CC Braided Hoses Equivalent Length Design Guide Equivalent length values at various numbers of 90 degree bends at 2/51 mm center line bend radius Length of Stainless Steel Flexible Outlet 1 2 3 4 5 6 7 8 9 10 11 12 Hose Size Bend Bends Bends Bends Bends Bends Bends Bends Bends Bends Bends Bends inches/ inches/ feet/ feet/ feet/ feet/ feet/ feet/ feet/ feet/ feet/ feet/ feet/ feet/ mm mm meters meters meters meters meters meters meters meters meters meters meters meters 31/790 Y2!15 8.5/2.6 11.0/3.4 13.0/4.0 16.0/4.9 N.A N.A N.A N.A N.A N.A N.A N.A W/20 10.0/3.0 12.5/3.8 14.0/4.3 17.0/5.2 N.A N.A N.A N.A N.A N.A N.A N.A 36/915 '/x/15 13.5/4.1 16.0!4.9 18.0/5.5 19.0/5.8 21.0/6.4 N.A N.A N.A N.A N.A N.A N.A 3/4720 14.0/4.3 17.0/5.2 19.5/5.9 20.0!6.1 23.0/7.0 N.A N.A N.A N.A N.A N.A N.A 48!1220 ½/15 15.5!4.7 17.0!5.2 19.5/5.9 20.0/6.1 21.0/6.4 22.0!6.7 28.0!8.5 32.0!9.8 N.A N.A N.A N.A /.r!2O 17.0/5.2 19.0/5.8 21.5!6.6 24.5/7.5 26.0/7.9 27.0/8.2 30.0/9.1 37.0!11.3 N.A N.A N.A N.A 60/1525 ½/15 21.5/6.6 24.0!7.3 27.0!8.2 28.5/8.7 1 30.0/9.1 31.0/9.4 37.0/11.3 42.0/12.8 44.0/13.4 46.0/14.0 N.A N.A 1/4720 23.0!7.0 24.0/7.3 28.0/8.5 29.5/9.0 30.5/9.3 31.0/9.4 38.0/11.6 42.0/12.8 44.0/13.4 46.0/14.0 N.A N.A 72/1830 ½/iS 30.0/9.1 32.0/9.8 36.5/11.1 37.5/11.4 40.5/12.5 141.0/12.8 142.0/12.8 46.0/14.0149.0/14.9152.0/15.8154.0/16.5 55.0/16.8 32.0/9.8 32.5/9.9 35.0/10.7 35.5/10.8 40.0/12.3 40.5/12.341.0/12.S 46.0/14.e 50.0/15.2 51.0!15.5 52.0/15.8 53.0/16.2 NOTES: values for use with 5.75/140mm straight reducers. How to use this Design Guide: For some systems, it may be advantageous for the designer to calculate the system hydraulics using shorter equivalent lengths associated with fewer than the maximum allowable number of bends. In this case, the designer may select a design number of bends for the job and use the associated equivalent length from the design guide to determine the system hydraulics. It is possible that the actual installed condition of some of the flexible drops may have more bends than the designer selected: When this happens, the design guide may be used to find equivalent lengths based on the actual installed number of bends for particular sprinkler installations. The system hydraulics can be recalculated using actual equivalent lengths to verily the performance of the system. 10.85 5839 Rev AG Updated 07/2019 © 2019 victaulic Company. All rights reserved. victaulic.com 18 \JtaUIiC ri victaulic.com -I 5.1 PERFORMANCE -FRICTION LOSS DATA Series AH2 and AH2-CC Braided Hoses Style A81, AB2, AB3, AB4, AB5, AB7, AB7 Adj., AB8, AB10, AB12, ABBA and ABMM VicFlex Brackets Length of Stainless Steel Flexible Hose inches/mm K-Factor Imperial/S.I. Outlet Size inches/mm/type Equivalent Length of 1/33.7mm Sch. 40 Pipe feet/meters Maximum Number of 9O Bends at 7/178mm Bend Radius 31/790 5.6/8.1 ½/IS/Straight 13.8/4.2 2 u/2 /15/90 Elbow 23.5/7.1 36/915 5.6/8.1 ½/i5/Straight 16.6/5.1 2 ½"/15/90 Elbow 25.6/7.8 48/1220 5.6/8.1 1/2'/15/Straiqht 23.4/7.1 30.7/9.3 i/z"/15/90 Elbow 60/1525 5.6/8.1 1/2 /15/Straight 30.2/9.2 35.9/10.9 1/2"/l 5/90' Elbow 72/1830 - 5.6/8.1 - 'W/15/Straight 37.0/11.3 41.1/12.5 ½"/15/90 Elbow 31/790 / 8.0/11.5 3/4 /20/Straight 16.8/5.1 - 2 /4 °/20/90 Elbow 16.8/5.1 36/915 8.0/11.5 /4/20/Straight 20/6.0 2 1/4"/20/90 Elbow 19.7/6.0 48/1220 8.0/11.5 1/4"/20/Straight 27.8/8.4 26.6/8.1 3/4"/20/90 Elbow 60/1525 8.0/11.5 1/4"/20 Straight 35.7/10.9 33.6/10.2 3/4°/20/90 Elbow 72/1830 8.0/11.5 1/4"/20/Straight 43.5/13.2 40.6/12.2 /4"/20/90 Elbow 31/790 11.2/16.1 3/4 /20/Straight 16.5/5.0 2 A"/20/90 Elbow 17.8/5.4 36/915 11.2/16.1 1/4"/20/Straight 19.5/5.9 2 ~/20/90 Elbow 20.7/6.3 48/1220 11.2/16.1 3%°/20/Straight - 26.7/8.1 27.9/8.5 /4'/20/90 Elbow 60/1525 11.2/16.1 3/4'/20/Straight 33.9/10.3 35/10.7 3/4 /20/90 Elbow 72/1830 11.2/16.1 3/4"/20/Straight 41.3/12.5 42.2/12.8 3/4'/20/90 Elbow 31/790 14.0/20.2 3%°/20/Straight 14.9/4.5 2 /4/20/90 Elbow 15.5/4.72 36/915 14.0/20.2 34/20/Straight 19.4/5.9 2 W/20/90 Elbow 19.6/5.9 48/1220 14.0/202 34"/20/Straight 30.3/9.2 29.5/8.9 W/20/90 Elbow 60/1525 14.0/20.2 1/4 /20/Straight 33.9/10.3 34.1/10.4 1/4'/20/90* Elbow 72/1830 14.0/20.2 3/i/20/Straight 37.5/11.4 38.6/11.7 3/4'/20/90 Elbow 1 FM NOTES: The Series AH2 hose has been tested and Approved by FM Global for use in wet, dry and preaction systems per NFPA 13, 13R, and 13D and FM data sheets 2-0, 2-5, and 2-8. FM 1637 standard for safety include, but are not limited to, pressure cycling, corrosion resistance, flow characterisitics, vibration resistance, leakage, mechanical and hydrostatic strength. EXAMPLE: A 48-inch hose installed with two 30° bends and two 90° bends is permitted and considered equivalent to the data in the table shown above. In this example, the total number of degrees is 2400, which is less than the allowable 270°. 10.85 5839 Rev AG Updated 07/2019 © 2019 Victaulic Company. All rights reserved. victaulic corn 19 /3tIUIiC victaulic.com 5.2 PERFORMANCE - FRICTION LOSS DATA Series AH2 Braided Hose with 900 Low Profile Elbows Style A135, AB11, A1312, ABBA and ABMM VicFlex Bracket Length of Stainless Steel Flexible Hose inches/mm K-Factor Imperial/S.I. Outlet Size inches/mm Equivalent Length of 1/33.7mm Sch. 40 Pipe feet/meters Maximum Number of 90° Bends at 7/178mm Bend Radius 31/790 5.6/8.1 1/2°/15 13.7/4.2 2 36/915 5.6/8.1 ½°/15 17.0/5.2 2 48/1220 5.6/8.1 1/2"/15 25.0/7.6 3 60/1525 5.6/8.1 W/15 33.0/10.1 4 72/1830 5.6/8.1 ½°/15 41.1/12.5 4 31/790 8.0/11.5 A'/20 13.6/4.14 2 36/915 8.0/11.5 1/4"/20 16.9/5.2 2 48/1220 8.0/11.5 /4'/20 27.8/8.5 3 60/1525 8.0/11.5 3/4°/20 32.6/9.9 4 72/1830 8.0/11.5 ,4"/20 40.6/12.4 4 31/790 11.2/16.1 3/4°/20 13.7/4.2 2 36/915 11.2/16.1 %°/20 17.0/5.2 2 48/1220 11.2/16.1 4"/20 24.9/7.6 3 60/1525 11.2/16.1 1/4 /20 32.9/10.0 4 72/1830 11.2/16.1 3/4 /20 40.9/12.5 4 31/790 14.0/20.2 1/4"/20 13.5/4.1 2 36/915 14.0/20.2 3/4°/20 16.8/5.1 2 48/1220 14.0/20.2 1/4°/20 24.7/7.5 3 60/1525 14.0/20.2 1/4'/20 32.7/9.9 4 72/1830 14.0/20.2 1/4"/20 40.7/12.4 4 FM NOTES: The Series AH2 hose has been tested and Approved by FM Global for use in wet, dry and preaction systems per NFPA 13, 13R, and 13D and FM data sheets 2-0, 2-5, and 2-8. FM 1637 standard for safety include, but are not limited to, pressure cycling, corrosion resistance, flow characterisitics, vibration resistance, leakage, mechanical and hydrostatic strength. EXAMPLE: A 48-inch hose installed with two 30° bends and two 90° bends is permitted and considered equivalent to the data in the table shown above. In this example, the total number of degrees is 240°, which is less than the allowable 270°. 10.85 5839 Rev AG Updated 07/2019 © 2019 Victaulic Company. All rights reserved. victaulic.com 20 J1tluI ii c victaulic.com 5.3 PERFORMANCE - FRICTION LOSS DATA Series AH2 and AH2-CC Braided Hose Style A131, AB2, A134, AB5, A137, AB7 Adj., AB8, AB10, AB11 and AB12 Brackets Equivalent Length of Maximum Number Length of steel pipe according to of 900 Bends at Stainless Steel Outlet EN 10255 ON 25 3/76.2mm Bend Flexible Hose Size (33,7 x 3,25) Radius - mm/inches mm/inches - meters/feet meters/feet - 31/790 - lSmm/W - 5.5/18.0 3 20mm/3/4 15mm/1/2' 36/915 6.4/21.0 3 20mm/l/4 15mm/½ 48/1220 8.5/27.9. 3 20mm/3/4 15 M111/1/2" 60/1525 10.7/35.1 4 20mm/l/4 72/1830 15mm/W 12.8/42.0' 4 20mm/l/4 Ili VDS CEILING MANUFACTURERS LIST AB1, AB2, AB7, ABIO ,AB11 A134 A135, AB8 1. AMF No specific approval 1. Hilti 2. Armstrong Knauf Chicago Metallic 3. Lafarge 4. Dipling 4. Lindner 5. Durlum 5. Rigips Geipel Gema-Armstrong Hilti Knauf Lafarge Linder Odenwald Richter Rigips Rockfon Pagos Suckow & Fischer USG Donn Series AH2 and AH2-CC Braided Hose Style AB1, AB2, AB3, AB4, AB5, AB7, AB8, and AB10 Brackets Length of Equivalent Length Maximum Stainless of steel pipe Number of Steel according to 90° Bends at Flexible Outlet EN 10255 ON 25 3/76.2mm Hose Size (33,7 x 3,25) Bend Radius mm/inches mm/inches/type meters/feet 15 mm/l/2"/Straight790/31 1.8/6.0 2 15 mm/½'/Straight 915/36 3.6/11.9 3 20mm/3/4'/Straight 1220/48 15 mm/'/u'/Straight 4.3/14.0 3 20 mmP/4'/Straight 15 mm/½'/Straight 1525/60 4.1/13.6 20 mm/3/i'/Straight 3 1830/72 15mmP/z'/Straight 5.5/18.1 [ 3 Series AH2 Braided Hose Style AB1, AB2, AB3, A134, AB5, AB7, AB8, AB10 and AB12 Brackets Length of Flexible Equivalent Length of Hose 1/33.7mm Sch. 40 Pipe mm inches Straight Configuration Bend Configuration 790 0.87 ' 2.70 31 2.9 8.9 915 1.00 2.80 36 3.3 9.2 1220 2.23 4.66 48 7.3 15.3 1525 2.90 6.5 60 9.5 21.3 1830 3.31 7.16 72 10.9 - 23.5 CCCF NOTE Friction loss data is in accordance with GB5135.16 tested at 110w rate of 114 liters per minute (30 gallons per minute). 10.85 5839 Rev AG Updated 07/2019 © 2019 Victaulic Company. All rights reserved. victaulic.com 21 X.04c_ —tau I ii C~ victaulic.com 6.0 NOTIFICATIONS v,vrvvr A. Read and understand all instructions before attempting to install, remove, adjust, or maintain any Victaulic piping products. Always verify that the piping system has been completely depressurized and drained immediately prior to installa- tion, removal, adjustment, or maintenance of any Victaulic products. Wear safety glasses, hardhat, and foot protection. Failure to follow these instructions could result in death or serious personal injury and property damage. - A&CrW1rflJIKIr .. r. . . IA It is the responsibility of the system designer to verify suitability of 300-series stainless steel flexible hose for use with the intended fluid media within the piping system and external environments. The effect of chemical composition, pH level, operating temperature, chloride level, oxygen level, and flow rate on 300-series stainless steel flexible hose must be evaluated by the material specifier to confirm system life will be acceptable for the intended service. Failure to follow these instructions could cause product failure, resulting in serious personal injury and/or property damage. / 10.85 5839 Rev AG Updated 07/2019 © 2019 Victaulic Company. All rights reserved. victaulic.com 22 ___________ victaulic.com 7.0 REFERENCE MATERIALS - CHARACTERISTICS VicFlex Maximum Load Values Series AH2 Hose with 24" Bracket Actual Length Total Load Max. Uniform Load ft Model Size m lb N lb/Iinearft N/linearm 31/790 0.8 2.6 5.2 23 2.6 38 36/915 o 3 9 5.5 25 2.8 40 48/1220 1.2 6.3 28 3.1 46 60/1525 15 7.0 31 3.5 51 72/1830 168 Series AH2 Hose with 48" Bracket Actual Length Total Load Max. Uniform Load ft Model Size m lb N lb/linear ft N/linear m 31/790 2.6 6.1 0.8 27 1.5 22 36/915 0.9 6.4 29 1.6 23 48/1220 12 7.2 32 1.8 26 60/1525 15 7.9 35 2.0 29 72/1830 168 . 8.7 39 2.2 32 Total Load is defined as the sum of the weights of the following: water-filled flexible sprinkler hose with threaded end fittings, including a typical fire sprinkler bracket assembly (any applicable Victaulic bracket model of the relevant associated size) ASTM C 635: Suspension System Load-Carrying Capabilities (excerpted) Suspension System Actual Length ft/rn Mm. Allowable Uniform Load j lb/linear ft N/linear m Direct Hung Light 5.0 75.7 Intermediate 12.0 181.0 Heavy - 16.0 241.7 SUMMARY: All direct-hung suspension system duty classifications per ASTM C 635 are able to withstand the maximum water-filled weight of the VicFlex sprinkler hose and bracket. 10.85 5839 Rev AG Updated 07/2019 © 2019 Victaulic company. All rights reserved. victaulic.com 23 X. A _C_ _tZ a _U1 i C; ~ victaulic.com 7.0 REFERENCE MATERIALS - CHARACTERISTICS (CONTINUED) Flexible Hose In-Plane Bend Characteristics One Bend Two Bends Three Bends 2'X Mini IX Minimum -doclius bend radius d radius OR Minimum OR bend radius go- Knimum Minimum b-d,arlh., radius NOTE For out-of-plane (three-dimensional) bends, care must be taken to avoid imparting torque on the hose. I-VicFlex-ABI-A82-AB1O !-hicF1ex-AB3 l-VicFlex-A84 l-VicFlex-AB7 I- yin F len-A B 8 I-VicFlex-A812 I-VicFlex-ABBA l-VicFlex-ABMM ri User Responsibility for Product Selection and Suitability Each user bears final responsibility for making a determination as to the suitability of Victaulic products for a particular end-use application, in accordance with industry standards and project specifications, and the applicable building codes and related regulations unwell as Victaulic performance, maintenance, safety, and warning instructions. Nothing in this or any Other document, nor any verbal recommendation, advice, or opinion from any Victaulic employee, shall be deemed to alter, vary, supersede, or waive any provision of Victaulic Company's standard Conditions of sale, installation guide, or this disclaimer. Intellectual Property Rights No statement contained herein concerning a possible or suggested use of any material, product, service, or design is intended, or should be constructed, to grant any license under any patent or other intellectual property right of Victaulic or any of its sabsidaries or affiliates covering such use or design, or as a recommendation for the use of such material, product, service, or design in the infringement of any patent or other intellectual property right. The terms "Patented" or Patent Pending" refer to design or utility patents or patent applications for articles and/or methods of use in the United States and/or other Countries. Note This product shall be manufactured by Victaulic or to Victuulic specifications. All products to be installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations. Installation Reference should always be made to l-VICFLEX-A13I-AB2-A810, l-VICFLEX-A84, I-VICFLEX-AB7, or l-VICFLEX-A88 to, the product you are installing. Handbooks are included with each shipment of Victaulic products for complete installation and assembly data, and are available in PDF format on our websile at www.vicluulic.com. Warranty Refer to the Warranty section of the current Price List or contact Victaulic for details. Trademarks Victaulic and all other Victaulic marks are the trademarks or registered trademarks of Victaulic Company, and/or its affiliated entities, in the U.S. and/or other countries. 10.85 5839 Rev AG Updated 07/2019 © 2019 Victaulic company. All rights reserved. victauliT.cnm 24 III, " A _C_ —ts _U1 ii C: