Loading...
HomeMy WebLinkAbout5818 EL CAMINO REAL; ; FPC2017-0348; Permitq:Cityof PERMIT REPORT Carlsbad Print Date: 10/20/2021 Permit No: FPC2017-0348 Job Address: 5818 EL CAMINO REAL, CARLSBAD, CA 92008-8816 Status: Closed - Finaled Permit Type: FIRE-Construction Commercial Work Class: Fire Sprinklers Parcel if: 2090503000 Track if: Applied: 11/22/2017 Valuation: $10,000.00 Lot if: Issued: 01/10/2018 Occupancy Group: Project U: Finaled Close Out: 09/16/2021 #of Dwelling Units: Plan #: Bedrooms: Construction Type: Bathrooms: Orig. Plan Check if: Inspector: Plan Check if: Final Inspection: Project Title: Description: ALPHATECSPINE -STORAGE RACK SPRINKLERS (DENSITY UPGRADE) Applicant: FPContractor: TITAN FIRE PROTECTION INC TITAN FIRE PROTECTION INC CHRISTIAN MCGREGOR 1341 DISTRIBUTION WAY, if STE 14 1341 DISTRIBUTION WAY, U STE 14 VISTA, CA 92081-8843 VISTA, CA 92081-8843 (760) 295-3436 (760) 295-3436 FEE AMOUNT FIRE NFPA 13 or 1,311 System 7 - 100 heads $536.00 Total Fees: $536.00 Total Payments To Date: $536.00 Balance Due: $0.00 Fire Department Page 1 of 1 1635 Faraday Avenue, Carlsbad CA 92008-7314 1 760-602-4665 1 760-602-8561 f I www.carlsbadca.gov ft 2o 1 q -o+ Fire Protection by Computer Design Titan Fire Protection Inc 2880 Scott Street, Suite 105 Vista, CA 92081 760.295.3436 Job Name Alphatec - Highpile Density Upgrade Building : 17565 Location : 5818 El Camino Real, Carlsbad, CA 92008 System : 1 Contract : 17565 Data File : Aiphatec hand listed 31ines w2.5 RN.WXF Computer Programs by Hydratec Inc. Route 111 Windham N.H. USA 03087 i Titan Fire Protection Inc Page 1 Aiphatec - Highpile Density Upgrade Date 11.20.2017 HYDRAULIC CALCULATIONS for Project name: Aiphatec - Highpile Storage Upgrade Location: 5818 El Camino Real, Carlsbad, CA 92008 Drawing no: 17565 Date: 12.05.2017 Design Remote area number: 1 Remote area location: Warehouse above highpile racks Occupancy classification: Rack Storage Class I & II Commodities. Density: .546 - Gpm/SqFt Area of application: 864 - SqFt Coverage per sprinkler: 144 - SqFt Type of sprinklers calculated: Tyco, EC-25,TY9128, k25.2, Brass, Up,212 No. of sprinklers calculated: 6 In-rack demand: N/A - GPM Hose streams: 250 - GPM Total water required (including hose streams): -GPM @ - Psi Type of system: AUTOMATIC WET FIRE SPRINKLER SYSTEM Volume of dry or preaction system: N/A - Gal Water supply information Date: 8.18.2017 Location: East of El Camino Real, South of Faraday Source: City of Carlsbad Water Availability Name of contractor: Titan Fire Protection Inc. Address: 2880 Scott St. Ste 105,Vista, CA 92081 Phone number: 760.295.3436 Name of designer: C. McGregor Authority having jurisdiction: City of Carlsbad Fire Prevention Notes: (Include peaking information or gridded systems here.) Hydralic density upgrade are made by Titian Fire are to comply with hydralic requirements outlined by Klausbruckner & Associates report dated March 27, 2017. I have attached a copy of that report for plan check referance with these hydralic calculations. Computer Programs by Hydratec Inc. Route 111 Windham N.H. USA 03087 Water Supply Curve C Titan Fire Protection Inc Page 2 Aiphatec- Highpile Density upgrade Date 11.20.2017 City Water Supply: Demand: Cl - Static Pressure : 90.9 Dl - Elevation : 12.199 C2 - Residual Pressure: 79.9 D2 - System Flow : 839.73 C2 - Residual Flow : 3900 . D2 - System Pressure : 84.759 Hose ( Demand) : 250 03- System Demand :1089.73 Safety Margin : 5.101 150 140 130 p120 R11° E10° 90 O2 ----------_ C2 03 S80 u 70 - R6° E5° 40 30 20 10 -0-1- - 400 800 1200 1600 2000 2400 2800 3200 3600 FLOW (Nd1.85) Computer Programs by Hydratec Inc. Route 111 Windham N.H. USA 03087 Fittings Used Summary Titan Fire Protection Inc Page 3 Aiphatec - Highpile Density Upgrade Date 11.20.2017 Fitting Legend Abbrev. Name 'A % 1 VA 11/2 2 21/2 3 31/2 4 5 6 8 10 12 14 16 18 20 24 B NFPA 13 Butterfly Valve 0 0 0 0 0 6 7 10 0 12 9 10 12 19 21 0 0 0 0 0 E NFPA 139O'StandardElbow 1 2 2 3 4 5 6 7 8 10 12 14 18 22 27 35 40 45 50 61 F NFPA 1345 Elbow 1 1 I 1 2 2 3 3 3 4 5 7 9 11 13 17 19 21 24 28 Fsp Flow Switch Potter VS Fitting generates a Fixed Loss Based on Flow T NFPA I39O' Flow thruTee 3 4 5 6 8 10 12 15 17 20 25 30 35 50 60 71 81 91 101 121 Units Summary Diameter Units Inches Length Units Feet Flow Units US Gallons per Minute Pressure Units Pounds per Square Inch Note: Fitting Legend provides equivalent pipe lengths for fittings types of various diameters. Equivalent lengths shown are standard for actual diameters of Sched 40 pipe and CFactors of 120 except as noted with. The fittings marked with a * show equivalent lengths values supplied by manufacturers based on specific pipe diameters and CFactors and they require no adjustment. All values for fittings not marked with a * will be adjusted in the calculation for CFactors of other than 120 and diameters other than Sched 40 per NFPA. Computer Programs by Hydratec Inc. Route 111 Windham N.H. USA 03087 Pressure I Flow Summary - STANDARD Titan Fire Protection Inc Page 4 Alphatec- Highpile Density Upgrade Date 11.20.2017 Node Elevation K-Fact Pt Pn Flow Density Area Press No. Actual Actual Req. A 28.167 25.2 30.0 na 138.03 0.546 144 30.0 B 28.167 25.2 31.49 na 141.41 0.546 144 30.0 6 0.0 67.11 na C 27.917 25.2 30.09 na 138.24 0.546 144 30.0 D 27.917 25.2 31.59 na 141.63 0.546 144 30.0 10 27.917 55.08 na E 27.667 25.2 30.21 na 138.51 0.546 144 30.0 F 27.667 25.2 31.71 na 141.91 0.546 144 30.0 G 27.667 55.28 na 7 25.25 64.69 na 11 25.25 64.73 na H 25.25 64.86 na 12 24.517 66.44 na 13 24.517 66.82 na TOR 24.517 68.91 na BOR 0.5 81.66 na BF1 -3.0 84.02 na BF2 3.0 81.68 na BF3 -3.0 85.4 na BF4 -3.0 85.73 na TEST 0.0 84.76 na 250.0 The maximum velocity is 24.62 and it occurs in the pipe between nodes F and G Computer Programs by Hydratec Inc. Route 111 Windham N.H. USA 03087 Final Calculations - Hazen-Williams Titan Fire Protection Inc Page 5 Aiphatec - Highpile Density Upgrade Date 11.20.2017 Hyd. Qa Dia. Fitting Pipe Pt Pt Ref. "C" or Ftng's Pe Pv Notes Point Qt Pf/Ft Eqv. Ln. Total Pf Pn A 138.03 2.157 0.0 10.750 30.000 K Factor = 25.20 to 120.0 0.0 0.0 0.0 B 138.03 0.1386 0.0 10.750 1.490 Vel = 12.12 B 141.41 2.157 0.0 45.833 31.490 K Factor = 25.20 to 120.0 0.0 0.0 12.199 6 279.44 0.5110 0.0 45.833 23.421 Vel = 24.53 6 0.0 2.635 2T 32.948 3.000 67.110 to 120.0 E 8.237 41.185 -10.936 7 279.44 0.1928 0.0 44.185 8.519 Vel = 16.44 0.0 279.44 64.693 K Factor= 34.74 C 138.24 2.157 0.0 10.750 30.095 K Factor = 25.20 to 120.0 0.0 0.0 0.0 D 138.24 0.1390 0.0 10.750 1.494 Vel = 12.14 D 141.64 2.157 0.0 45.833 31.589 K Factor = 25.20 to 120.0 0.0 0.0 0.0 10 279.88 0.5125 0.0 45.833 23.489 Vel = 24.57 10 0.0 2.635 2T 32.948 2.750 55.078 to 120.0 E 8.237 41.185 1.155 11 279.88 0.1934 0.0 43.935 8.495 Vel = 16.47 0.0 279.88 64.728 K Factor= 34.79 E 138.51 2.157 0.0 10.750 30.211 K Factor = 25.20 to 120.0 0.0 0.0 0.0 F 138.51 0.1394 0.0 10.750 1.499 Vel = 12.16 F 141.91 2.157 0.0 45.833 31.710 K Factor = 25.20 to 120.0 0.0 0.0 0.0 G 280.42 0.5143 0.0 45.833 23.573 Vel = 24.62 G 0.0 2.635 2T 32.948 2.750 55.283 to 120.0 E 8.237 41.185 1.047 H 280.42 0.1940 0.0 43.935 8.525 Vel = 16.50 0.0 280.42 64.855 K Factor= 34.82 7 279.44 6.357 0.0 13.330 64.693 to 120.0 0.0 0.0 0.0 11 279.44 0.0026 0.0 13.330 0.035 VeI= 2.82 11 279.88 6.357 0.0 13.330 64.728 to 120.0 0.0 0.0 0.0 H 559.32 0.0095 0.0 13.330 0.127 Vel = 5.65 H 280.41 6.357 E 17.603 45.000 64.855 to 120.0 0.0 17.603 0.317 12 839.73 0.0203 0.0 62.603 1.269 Vel = 8.49 12 0.0 6.357 E 17.603 0.917 66.441 to 120.0 0.0 17.603 0.0 13 839.73 0.0202 0.0 18.520 0.375 Vel = 8.49 13 0.0 6.357 2E 35.205 68.000 66.816 to 120.0 0.0 35.205 0.0 TOR 839.73 0.0203 0.0 103.205 2.090 Vel = 8.49 Computer Programs by Hydratec Inc. Route 111 Windham N.H. USA 03087 Final Calculations - Hazen-Williams Titan Fire Protection Inc Page 6 Alphatec- Highpile Density Upgrade Date 11.20.2017 Hyd. Qa Dia. Fitting Pipe Pt Pt Ref. "C" or Ftngs Pe Pv Notes Point Qt Pf/Ft Eqv. Ln. Total Pf Pn TOR 0.0 6.357 B 12.573 54.017 68.906 to 120.0 Fsp 0.0 12.573 11.402 * * Fixed Loss = BOR 839.73 0.0202 0.0 66.590 1.348 Vel = 8.49 BOR 0.0 7.68 3E 67.666 68.000 81.656 to 150.0 2F 22.555 90.221 1.516 BFI 839.73 0.0053 0.0 158.221 0.844 Vel = 5.82 BF1 0.0 8.27 2E 56.936 6.000 84.016 to 140.0 0.0 56.936 -2.599 BF2 839.73 0.0042 0.0 62.936 0.267 Vel = 5.02 BF2 0.0 8.27 EqI 23.723 5.000 81.684 to 140.0 0.0 23.723 3.599 * * Fixed Loss = 1 BF3 839.73 0.0042 0.0 28.723 0.121 Vel = 5.02 BF3 0.0 8.27 2E 56.936 19.000 85.404 to 140.0 EqI 1.582 58.518 0.0 BF4 839.73 0.0042 0.0 77.518 0.328 Vel = 5.02 BF4 0.0 7.68 2E 39.705 14.167 85.732 to 140.0 0.0 39.705 -1.299 TEST 839.73 0.0061 0.0 53.872 0.326 Vel = 5.82 250.00 Qa = 250.00 1089.73 84.759 K Factor = 118.37 Computer Programs by Hydratec Inc. Route 111 Windham N.H. USA 03087 Iss KLAUSBRUCKNER 2495 Truxtun Road, Suite 205 AND ASSOCIATES San Diego, CA 92106 Tel: (619)677-2004 Fax: (619) 677-2444 ALPHATEC SPINE 5818 EL C CARLSBAD [iI ombustible rage Report Rev 1.0 March 27, 2017 :• 99.1 ANN lB 1.0 Preliminary Report March 27, 2017 Mlvi DISCLAIMER This report is the property of Klausbruckner & Associates, Inc. and was prepared exclusively for use by Alphatec Spine for the storage & occupancy conditions described in this report. Alphatec Spine conditions and operations addressed herein are based on information provided to the report by Alphatec Spine. Discrepancies between the information presented herein and actual conditions and conditions presented on plans are the sole responsibility of Alphatec Spine. Verification of compliance with the Code requirements and provisions addressed herein is outside the scope of this report. Copies of this report retained by Alphatec Spine shall be utilized only by Alphatec Spine for the storage and occupancy conditions and the 2013 California Fire Code conditions and requirements addressed in this report. This report shall not be used for the purpose of construction for this project or any other project or for any other purpose. Rev 1.0 —Aiphatec Spine Page iii I 5818 El Camino Real, Carlsbad, CA KLAUSBRUCKNE R AND ASSOCIATES I Table of Contents SUMMARY TABLE .............................................................................................................................1 INTRODUCTION.................................................................................................................................3 BUILDING CONSTRUCTION, DESIGN, AND OCCUPANCIES..................................................4 3.1 BUILDING CONSTRUCTION & DESIGN ..................................................................................................4 3.2 OCCUPANCIES ......................................................................................................................................4 HIGH-PILED STORAGE REQUIREMENTS...................................................................................5 4.1 AUTOMATIC FIRE SPRINKLER SYSTEM.................................................................................................6 4.1.1 Rack Storage Area Sprinkler Protection .....................................................................................6 4.1.2 Additional Protection Requirements............................................................................................7 4.1.2.1 Extent of Protection................................................................................................................................7 4.1.2.2 Protection of Steel Columns ........................................ ...................................................................7 4.1.2.3 Fixed Obstructions ..................................................... .............................................................7 4.1.2.4 Ceiling Slope ........................................................ 1'...........(...................................7 4.1.3 Remainder of Building - Outside the Scope.....:. .'....................................................7 4.2 ALARM/MONITORING..............................................................S...... .. ......................................7 4.3 BUILDING ACCESS —DOORS & ROADS...........................\ .\... ................................8 4.3.1 Access Doors ....................................................... .... .... ................ .,..7................................ 8 4.3.2 Access Roads ........................................ .......\.\...............................................8 4.4 SMOKE AND HEATREMOVAL..................../........\.\...............................................8 4.5 DRAFT CURTAINS..................................../7...................../..............................................8 4.6 PORTABLE FIRE EXTINGUISHERS ................ . ........... L/.\.............................................................9 4.7 AISLE WIDTHS ...............................................L./...................................................................9 4.8 HOUSEKEEPING &MAINtENANCE.I./........I...........LI.............................................................. 10 ,. 4.9 FLUE SPACES FOR RACK.SToRAGE\................................................................................, .......10 MEANS OF EGRESS ..............................................................................................11 5.1 STORAGE [S-i OCCUPA ........11 5.2 REMAINDER OF BUILIIIG - OUTSIDE'HE SCOPE ..............................................................................Ii EXPOSURES ............. \..\X.>....................................................................................12 6.1 OCCUPANCY SEPARAT..........................................................................................12 6.2 SEPARATION OF HIGH-PILED STORAGE AREAS ..................................................................................12 6.3 ALLOWABLE AREA AND SIDEYARDS..................................................................................................12 CONCLUSION....................................................................................................................................13 APPENDIX A: ATTACHMENTS.....................................................................................................14 Rev 1.0—Aiphatec Spine Page iii I 5818 El Camino Real, Carlsbad, CA K USBRUCKNER I AND ASSOCIATES I I 1. Summary Table TOPIC CODE SECTION CRITERIA/REQUIREMENTS Construction Type Architectural Plans Existing. Unknown. Approximate Architectural Plans Warehouse: 5,313 ft2 (S-i) Square Footage [High-Piled Storage: <2,000 ft2 (S-i)] Remainder: Unknown ft2 lB/F-I/S-11 Building Total: Unknown ft2 [B/F-I/S-11 Occupancy CBC Section 302, Alphatec Spine: 304, 306, 311 Warehouse: S-1(Storage) Remainder: B/F-I/S-I - Outside the Scope CBC Table 508.4 Occupancy separation is not required between B, F-I and S-i. Storage CFC Sections Class I: Metal parts & instruments, spinal implants Commodity 3203.1, 3203.2, (small titanium pieces), aluminum trays. <5% 3203.3 plastic packaging proposed. Class II: Meta\parts & instruments, spinal implants J'1ak 'titium pieces), aluminum trays [,carton'd]. <5% plastic packaging proposed. Note: Aiphatec agrees to s itch' out plastic binboxes to metal cardboard bi):es and to e on the first racking level only. On behal of Aiphatec we are requesting that the be aIIo.we to ave s lf storage and metal cabinets witl metal p,arts storeinside, so ong as it islocated on the first Fievel qnly. Se Atla hnenl #3 for photos? Automatic CFC 3208.2, Table 'Ra,.Stoi4ge A?ea rinkler Protection: Class I & II Sprinkler Protection 3206.2 ( <"3 ,€ommodtis Icajtpned & exposed, encapsulated & non- encaPsultdI..'/ MaximumStorage Height: < 20'-0" Maximum Ceiling Height: <30'-O" NFPA-13 [2q13.]\ Sections'3.9..i.7.i /'—-'- Aisle Widths: >4 -2 \\ Sjpgle-row and Double-row Racks Open shelves, area >50% open \% Ceiling Sprinkler Design Required: NFPA-13 [20i31./ Control Mode Density Area sprinklers, minimum K-I 1.2, Sections 8.5.6.1, High Temperature (286°F), upright or pendent, listed for 12.6.3, 12.8.6.1, storage 16.2.1.3, 16.2.1.3.2.1 Minimum density interpolated for 4'-2" aisles: 0.546 Tables 8.6.2.2.1(0), gpmlfl2 over 2,300 ft2 remote area 12.8.6.1, 16.2.1.3.2, Maximum coverage area: 100 ft2 Figure 16.2.1.3.2(e) Maximum spacing between sprinklers: 12'-0" curves E & G Minimum clearance: 18" from deflector to top of storage Hose allowance: 500 gpm The existing sprinkler system is designed to provide a density of 0.45 gpm/f? over the most remote 3,000f? using EC-25 sprinklers. The existing sprinkler system must be revised and/or re-calculated. See section 4.1.2 of this report for additional protection requirements within the Rack Storage Area. All other areas are outside the scope of this report. Rev l.O—AlphatecSpine I S . S~ Page 1 KLAUSBRUCKNER 5818 El Camino Real, Carlsbad, CA AND ASSOCIATES Tonic CODE SECTION CRITERIA/REQUIREMENTS Smoke and Heat CFC Table 3206.2 Not required for sprinklered high piled storage area of Class Removal II Commodities < 12,000 ft2. Flue Spaces CFC Table 3208.3 Single Row Racks: Transverse - 3-inches required* Longitudinal - Not required Double Row Racks: Option #1: Transverse - 6-inches required* Longitudinal - Not required Option #2: Transverse - 3-inches required* Longitudinal - 6-inches required *Random variations are allowed, provided the distribution of water is not obstructed Draft Curtains CFC Table 3206.2 Draft Curtains are not required by Chapter 32 if the building is sprinklered Building Access CFC Table 3206.2 Access roads required by CFC Section 503 & Doors & Section 503 Access doors are not required by Chapter 32 for sprinklered high piled storage area of. Class II Commodities </l.2000 ft2. Access roads ar existth no proposed changes. Hose Connections CFC 3206.8 Not required un'lei)it"sageways are proposed within the high-piled storage areas. \ \ Aisle Width CFC 3206.9 Minimum reqed ai's.width'i. 414'-'' e required in sprinkler buildings with Alphapinegees intain a 50" minimum of aisle widtfs(withir/ 'ie,..jabk storage area in order to comply with .the 9ink1 requirements stated in section 4.1.1 of this CFC 1018.4 Exceptio2 ort. ( J Cead "\ ends'~5." 'cE: Any floor/palletized storage cannot obstruct the \ mininn width of the aisles. Alarm/Monitoring CFC 03.4 valves controlling the water supply for automatic sprinkler ystems and water-flow switches on all sprinkler systems (if serving more than 20 sprinklers) shall be electrically supervised by a listed fire alarm control unit. Fire Extinguishers CFC 906.1 & Table High-piled Storage Areas: 2-A:20-B:C 906.3(1), 906.3(2) Max travel distance: 50' Max area per Extinguisher: 3,000 ft' HazlMaterials N/A NA. Not Part of the Scope of This Report Allowable Area CBC Table 503 Not within the scope of this report. Existing Building. No proposed changes to type of construction, building square footage or occupancy. KLAUSBRUCKNER T_ Rev 1.0 —Aiphalec Spine I Page 2 5818 El Camino Real, Carlsbad, CA AND ASSOCIATES 2. Introduction The following is a high-piled combustible storage code compliance report for Alphatec Spine, located at 5818 El Camino Real in the city of Carlsbad, California. This report is intended to help both the owners and the fire department in expediting plan review and effectively determine the requirements necessary to meet the Fire Code. This report is based on the 2013 Editions of the California Fire Code and the Building Code, and the 2013 Edition of NFPA-13, Standardfor the Installation of Sprinkler Systems. I Rev 1.0 —Aiphalec Spine I Page KLAUSBRUCKNEfl 5818 El Camino Real, Carlsbad, CA AND ASSOCIATES 3. Building Construction, Design, and Occupancies 3.1 Building Construction & Design Alphatec Spine currently occupies an existing building. The warehouse is 5,313 ft2 and the high-piled storage area will be less than 2,000 ft2. No expansion or structural modifications to the buildings are planned at this time. The type of construction for the buildings is unknown (Attachment #1). 3.2 Occupancies The facility is used for warehousing, manufacturing, row and double-row rack storage with open shelve in the storage area. ( ( Alphatec Spine will be classified overall as a B/J) 304-311 (Attachment 92). ies and office space. Single- of at least 4'-2" is proposed defined by CBC APPROXIMATE USE ((oCde AREA SQ. F. Warehouse (1 5,313 High Piled S&age (<2,000) Remainder [Outside tfle\Scpe]\\ B)P1{S-1 Unknown 'tal: \\ B/F-i/S-1 Unknown Rev 1.0 —Alphatec Spine I Page 4 KLAUSDRUCKNER 5818 El Camino Real, Carlsbad, CA "..ASSOCIATES 4. High-Piled Storage Requirements The commodities are Class I-Il, stored cartoned and exposed, encapsulated and non- encapsulated, on open shelving in single-row and double-row racks (Attachment #3). Products (Attachment #3) Method of Storage Storage Height Cartoned? Encapsulated Commodity Class Metal parts & instruments, spinal implants (small titanium pieces), aluminum Rack < 205-0" No Yes & No I trays <5% plastic packaging proposed. Metal parts & instruments, spinal implants (small titanium pieces), aluminum Rack < 201-0" e Yes & No II trays <5% plastic '> packaging proposed Alphatec agrees to switch out plastic binb them on the first racking level only. Qnj AMW be allowed to have shelf storage and metal as it is located on the first level onlv.ee A o metal & dard binboxes and If o N hatec we are requesting ti ets wi h etal parts stored inside, n nt #3 or nhotosJ /\V f/ Ir-/ #4ih-pilec c bi3{ible storage area shall be based on y castored çcep,as provided in Section 3204.2. The hb'gis Class II, cartoned & exposed, encapsulated imen #the following fire protection requirements will be ie re mee)tquirements of CFC Chapter 32 and NFPA-13 for Per CFC 3204.1 (Attachm the highest hazard comf highest commodity stored and non-encapsulated. / Based on Table 3206.2 provided by Alphatec the entire high-piled stc Rev 1.0 —Alphalec Spine Page 5 5818 El Camino Real, Carlsbad, CA AUSUN ANO ASSOCIATES 4.1 Automatic Fire Sprinkler System The following requirements are based on NFPA-13 (2013 Edition) (Attachment #6): 4.1.1 Rack Storage Area Sprinkler Protection Commodity Stored: Class I & 11, cartoned & exposed [encapsulated and non-encapsulated] Type of Storage: Type of Rack Shelving: Flue Spaces for Standard Racks: Single Row Racks: Double Row Racks: Option #1: Option #2: Aisle Widths: Single and Double Row Racks 50% or greater open 3" TransverseAoIQgi.tudjnal not required 6" Transver ,LoIftkii0kJal not required 3" Transverse' 6"Longitbdi'ial ,. ? 4'-2" Maximum Storage Height: < 2006" Maximum Ceiling Ceiling Sprinkler Design: *o trot Mode Density Area (CA); minimum K lgh temperature sprinklers, listed for storage unrig ht or pendent; minimum density interpolated fo A 33 aisles 0.546 gpm/ft2 over 2,300 ft2 remote area aximum coverage area 100 ft2; maximum spacin between sprinklers 12'-0"; minimum 18" clearanc from deflector to ton of storae: hose allowance 50( The existing sprinkler system is designed to provide a density of 0.45 gpm/f12 over the most remote 3,000 f? using EC-25 sprinklers. The existing sprinkler system must be revised and/or re-calculated. Rev 1.0 —Alphalec Spine I Page LAUB B RU C KN ER 5818 El Camino Real, Carlsbad, CA ...ASSOCIATES 4.1.2 Additional Protection Requirements 4.1.2.1 Extent of Protection Per CFC 3206.2 and NFPA-13 Section 12.3 (Attachment #7), the extent and type of protection (including automatic sprinkler design densities) shall extend the lesser of 15 feet beyond the high-piled storage area or to a permanent partition. 4.1.2.2 Protection of Steel Columns Per CFC 3208.4 and NFPA-13 Section 16.1.4.1(2) and Table 16.1.4.1 (Attachment #7), where fireproofing of building columns is not provided and storage heights are in excess of 15 ft, protection of building columns within the rack structure or vertical rack members supporting the building shall be protected by ceiling sprinkler density of 0.44 gpm/ft2 over a minimum of 2,000 ft The required sprinkler design density specified is section 4.1.1 of this report meets and exceeds the requirement for protection of steel columnst\ 4.1.2.3 Fixed Obstructions Per NFPA-13 Sections 8.5.5.3.1 and 8.5.5.3.1. fire sprinklers are not required under fixed obstruction or open grate fl ri.h is in excess of 4 ft. 4.1.2.4 Ceiling Slope Per NFPA- 13 Section 12.1.2 (Attachment 7), J , qer"system criteria specified are intended to apply to buildings with cçiiip s opØ#,not ecding 2 in 12 (16.7 percent). 4.1.3 Remainder df~ -Q~74re Bi!din.< Outside the Scope All other areas within the,b utsi'de the scope of this report. 4.2 Alarm/Moñi Per CFC 903.4 (Attachment98)all valves controlling the water supply for automatic sprinkler systems, pumps, tanks, water levels and temperatures, critical air pressures, and water-flow switches on all sprinkler systems (if serving >20 sprinklers) shall be electrically supervised by a listed fire alarm control unit. Alarm, supervisory and trouble signals shall be distinctly different and shall be automatically transmitted to an approved supervising station or, when approved by the fire code official, shall sound an audible signal at a constantly attended location. One exterior approved audible device, located on the exterior of the building in an approved location, shall be connected to each automatic sprinkler system. Such sprinkler water-flow alarm devices shall be activated by water flow equivalent to the flow of a single sprinkler of the smallest orifice size installed in the system. Where a fire alarm system is installed, actuation of the automatic sprinkler system shall actuate the building fire alarm system. Visual alarm notification appliances shall not be required except when required by Section 907. Rev 1.0 —Aiphatec Spine I Page 7 KLAUSURUCKNER 5818£! Camino Real, Carlsbad, CA AND ASSOCIATES I 4.3 Building Access - Doors & Roads 4.3.1 Access Doors Per CFC Table 3206.2 (Attachment #9), fire department access doors are not required for sprinklered high-piled storage areas of Class II Commodities < 12,000 ft2. 4.3.2 Access Roads Per CFC 503.1.1 (Attachment #9), fire apparatus access roads shall be provided within 150 feet of all portions of the exterior walls of the first story of buildings as measured by an approved route. Per CFC 503.2 (Attachment #9), fire apparatus access roads shall have an unobstructed width of not less than 20 feet, exclusive of shoulders, except for approved security gates in accordance with Section 503.6, and an unobstructed vertical clearance of not less than 13 feet 6 inches. The fire code official shall have theuritY>to require an increase in the minimum access widths where they are inadeiate for fire or rescue operations. Fire apparatus access roads shall be designed and mitai12 ' port the imposed loads of fire apparatus and shall be surfaced so as to prove kll-weathe dri.pg capabilities. The required turning radius of a fire apparatus access road''stU\be deternilned by the fire code official. Dead-end fire apparatus access road's ?i\excess \of\1 50 feet in length shall be provided with an approved area for turnnnd"fiçe g/ appa)atus. The grade of the fire apparatus access road shall be within the (iiiityet'bished by the fire code official based on the fire department's apparatus. Tl3ang1e,of/approch>and departure for fire apparatus access roads shall be wit~in the ied byA € fire code official based on the fire department's apparatus. Fire access roads are exi iigandjve be'previously approved. 4.4 Smoke ahà lteái Removal Per CFC Table 3206.2 (Attachent #10), smoke and heat removal are not required for sprinklered high-piled storage areas of Class II Commodities < 12,000 ft2. 4.5 Draft Curtains Per CFC Table 3206.2 (Attachment #11), draft curtains are not required in sprinklered high-piled storage areas of Class II commodities < 12,000 ft2. Rev l.O—Alphatec Spine I Page 8 5818 El Camino Real, Carlsbad, CA I 4.6 Portable Fire Extinguishers Per CFC 906 and 3206.10 (Attachment 912), portable fire extinguishers shall be installed in the following locations: In new and existing Group B, F-i and S occupancies Where required by the sections indicated in Table 906.1. Per CFC Table 906.3(1) & 906.3(2) (Attachment #12), the following is the proposed fire Extinguisher type and layout: Storage Areas: 2-A:20-B:C @ Travel Distance 50 Feet The owners agree to comply with the requirements for fire extinguishers. One extinguisher may provide coverage to a maximum of 3000 ft2. Fire extinguisher types and locations will be provided by the owners or fire extinguisher vendor and approved by the fire department. Portable fire extinguishers shall be located in cc readily accessible and immediately available for paths of travel, unless the fire code official detert need for placement away from normal paths of tn be obstructed or obscured from view. In rooms or be completely avoided, means shall be provijedTh ocations where they will be ations shall be along normal jhazard posed indicated the 'efi'rejqinguishers shall not ici\yjaq obstruction cannot location of extinguishers. 4.7 Aisle Widths Y /7 ) j.-Y Per CFC 3206.9.1.1 (Atth\ment 473, aisles jspr.ilered buildings shall be a minimum of 44 inches. Per CFC 3209*(Excètion 1) cro aisles used only for employee access between aisles shall be a minimum of 24 inches in width. Dead ends greater thn 50 fee ln\hlg -piled storage areas are not recommended (Attachment #13). The owners agree to meet he above requirement for aisle widths and dead ends. Additionally, the owners agree to arrange their floor/palletized storage (if any) such that it does not obstruct the minimum required width of the aisles. Within the rack storage area, Aiphatec Spine agrees to maintain aisle widths to a minimum of 4'-2" (50") in order to comply with the sprinkler requirements stated in Section 4.1.1 of this report. Rev 1.0 —Alphalec Spine I Page 9 K LAUS B RUC KN E P 5818 El Camino Real, Carlsbad, CA AND ASSOCIATES 4.8 Housekeeping & Maintenance Per CFC 3205 (Attachment #14), the following are general maintenance and safety requirements, of which Alphatec Spine agrees to comply with: The structural integrity of racks shall be maintained. Smoking shall be prohibited. Approved "NO SMOKING" signs shall be conspicuously posted. When restocking is not being conducted, aisles shall be kept clear of storage, waste materials and debris. Fire department access doors, aisles and exit doors shall be unobstructed. During restocking operations using manual stocking methods, a minimum unobstructed aisle width of 24 inches of the required aisle width shall be maintained in 48 inch or smaller aisles, and a minimum unobstructed aisle width of one-half of the required aisle width shall be maintained in aisles greater than 48 inches. During mechanical stocking operations, a minimum unobstructed aisle width of 44 inches shall be maintained. 4.9 Flue Spaces for Rack Per CFC 3208.3 and Table 3208.3 (Attachment rack storage. Where required by the fire code o1 shall be equipped with approved devices to'o shall not be moved or modified. 1/ spa ss9tl be maintained for ed flue spaces in rack storage ui'rd flue space. Such devices Per CFC Table 3208.3 (Attachment in accordance with the foJ1bing:ç Single Row Racks:\ Double Row l Option Option #2: spaces for rack storage shall be ,e---3-finches required* inal - Not required Transverse - 6-inches required* IN Jpongitudinal - Not required Transverse - 3-inches required* Longitudinal - 6-inches required Random variations are allowed, provided the distribution of water is not obstructed ote: With flue spaces on first racking level (i.e. Floor Level) will be blocked as we ar questing the use of shelf storage will be stored within the racks on the first level only e sectionof this renort for additional information as well as Attachment #3 for ohol I Rev 1.0 —Aiphalec Spine I Page 10 kLAUSRRUCKNER 5818 El Camino Real, Carlsbad, CA AND ASSOCIATES 5. Means of Earess A complete exit analysis is outside the scope of this report and, when required, will be provided by the Architect of Record. The following general egress requirements apply to the proposed sprinklered occupancies (Attachment #16): 5.1 Storage [S-I Occupancy] Per CBC 1005.3.2, egress width components other than stairways shall be 0.2 inch/occupant. Per CBC Table 10 14.3, the common path of egress travel shall not exceed 100 feet. Per CBC Table 1015.1, one means of egress allowed for spaces with maximum occupant load of 29. Per CBC Table 1016.2, exit access travel distance shall not exceed 250 feet. Per CBC 1018.4 exception 2, dead ends through ommon path of egress shall not exceed 50 feet. 5.2 Remainder of Building All other areas within the building are outside the Scope I Rev 1.0 —Alphatec Spine I Page 11 KLAUSBRUCKNER 5818 El Camino Real, Carlsbad, CA AND ASSOCIATES 6. Exposures 6.1 Occupancy Separation Aiphatec Spine is classified overall as a B, F-i and S-i occupancy. Per CBC Table 508.4 (Attachment #17), there are no requirement for mixed occupancy fire barrier walls between B, F-i and S-I occupancies. 6.2 Separation of High-Piled Storage Areas Per CFC 3206.3.2.1 (Attachment #18), the aggregate of all high-piled storage areas within a building shall be used for the application of Table 3206.2 unless such areas are separated from each other by 1-hour fire barrier walls constructefL,n accordance with the California Building Code. Openings in such walls shall be protctedbfpening protective assemblies having a 1-hour fire protection rating. ( ( Alphatec Spine occupies the entire building; piled storage areas within Aiphatec Spine fron spaces do not apply. 6.3 Allowable Area The building is existing. square footage of the bui uirements of high of adjacent tenant to the occupancy, construction or Page 12 I Rev 1.0 —Alphalec Spine ANO ASsOCIATES 5818 El Camino Real, Carlsbad, CA KLAUSBRtJCKNCR 7. Conclusion It is the opinion of Klausbruckner & Associates that the above will meet the requirements, and/or intent of the 2013 Edition of the California Fire Code, the 2013 Edition of the California Building Code, and the 2013 Edition of NFPA- 13 Standard for the Installation of Sprinkler Systems, for the type of occupancy and storage. By way of my signature, Aiphatec Spine agrees to meet the storage conditions required and specified in this report. Alphatec Spine Representative Sign & Rev 1.0 —Alphatec Spine I Page 13 KLAUSBRUCKNER 5818 El Camino Real, Carlsbad, CA AND ASSOCIATES 8. Appendix A: Attachments Rev 1.0 —Alphatec Spine I I Page 14 5818 El Camino Real, Carlsbad, CA AND ASSOCIATES I R'cZot - -OS1' A jI TAN FIRE PROTECTION Fire Protection Contractor - License #989280 ALPHATEC- HIGHPILE STORAGE DENSITY UPGRADE 5818 EL CAMINO REAL, CARLSBAD, CA 92081 TITAN PROJECT# 17565 MATERIAL SUBMITTAL NOVEMBER 21, 2017 2880 Scott Street, Suite 105 - Vista, CA 92081 760-295-3881 —phone - 760-295-3437—fax www.titanfpinc.com tqca Fire Protection Products Worldwide Contacts www.tyco-fire.com Model EC-25 (CMDA and CMSA Applications) 25.2 (360) K-factor (360) Upright Sprinkler Extended Coverage General Description The TYCO Model EC-25 Extended Coverage (EC) 25.2K Upright Sprin- kler is a UL Listed, standard response, extended coverage Control Mode Density Area (CMDA) sprinkler for storage applications. It is also FM Approved as a quick response, extended coverage Control Mode Density Area (CMDA) sprinkler and as a Control Mode Specific Appli- cation (CMSA) sprinkler, as well as FM Approved for storage and non-stor- age applications. In addition, these sprinklers may be used in accordance with the new Chapter 21 of the 2013 edition of NFPA 13. As such, tables 21.2.2 and 21.3.2 of NFPA 13 may be utilized for design options. When used in accor- dance with NFPA Chapter 21, smoke vents and draft curtains are not required as specified in the 2015 edition of the International Building Code (IBC) and International Fire Code (IFC) for CMSA sprinklers with an All of 50 or less and a design of 12 or fewer sprinklers. These sprinklers offer a maximum cov- erage area of 196 ft.2 (18,2 m2), which is almost double the area offered by standard coverage sprinklers used for similar applications. The Model EC-25 Upright Sprinklers comply with the criteria for the protec- tion of retail stores as described in the 2013 Edition of NFPA 13, Section 20.3. IMPORTANT Always refer to Technical Data Sheet TFP700 for the "INSTALLER WARNING" that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and installation can permanently damage a sprinkler system or its compo- nents and cause the sprinkler to fail to operate in a fire situation or cause it to operate prematurely. Page 1 of 4 Where the FM Approval is utilized, the Model EC-25 Upright Sprinkler has successfully undergone full-scale fire testing at FM Global for ceiling-only storage and non-storage applica- tions. When used in conformance with applicable FM Global Property Loss Prevention Data Sheets, the Model EC-25 Sprinkler provides low hydrau- lic demand, the spacing advantages of extended coverage, and the obstruc- tion benefits of an upright sprinkler. For more information on applications and benefits of the Model EC-25 Sprin- kler, refer to the available white papers at www.tyco-fire.com. NOTICE The Model EC-25 Upright Sprinklers described herein must be installed and maintained in compliance with this document, as well as with the applica- ble standards of the National Fire Pro- tection Association (NFPA), in addition to the standards of any other authorities having jurisdiction (e.g., FM Global). Failure to do so may impair the perfor- mance of these devices. The owner is responsible for main- taining their fire protection system and devices in proper operating con- dition. Contact the installing contrac- tor or sprinkler manufacturer with any questions. Sprinkler Identification Number (SIN) TY9128 APRIL 2015 Technical Data Approvals UL and C-UL Listed: CMDA (Standard Response) FM Approved: CMDA and CMSA (Quick Response) NYC Approved under MEA 355-01-E (Approvals only apply to the service conditions indicated in the Design Cri- teria section.) Maximum Working Pressure 175 psi (12,1 bar) Pipe Thread Connection 1 Inch NPT orISO 7-R1 Discharge Coefficient K=25.2 gpm/p5i112 (362,9 1pm/bar112) Temperature Ratings 165°F (74°C) and 212°F (100°C) Maximum Coverage Area 196 ft.2 (18,2 m2) Finish Natural Brass Physical Characteristics Frame .............................Brass Deflector .........................copper Compression Screw ..........Stainless Steel Hook ............................MONEL Strut ............................MONEL Link Assembly................Solder, Nickel Button .............................Brass Sealing Assembly. Beryllium Nickel w/TEFLON Ejection Spring ..................INCONEL Deflector Nut........................Brass Response Time Index (RTI) Less than or equal to 50 (rn-s)05 TFP2I3 TFP2I3 Page 2 of 4 3 TEMPERATURE 2-9/16 DIA. 10 RATING I I (65,0 mm) 2 I I 1-Frame - I I Deflector Compression Screw 4 Hook __- 3-3/4 Strut I (95,3 mm) Link Assembly Il Button 6 9/16 Gasketed Spring Plate (14,3 mm) Ejection Spring 9 WRENCH NOMINAL Deflector Nut FLATS MAKE-IN ISO 7-131 pipe thread can be provided on special request. 7 1 NPT* FIGURE 1 MODEL EC-25 UPRIGHT SPRINKLER, 25.2K EXTENDED COVERAGE Operation The fusible link assembly is com- prised of two link halves that are joined together by a thin layer of solder. When the rated temperature is reached, the solder melts and the two link halves separate, allowing the sprinkler to acti- vate and flow water. Design Criteria UL and C-UL Listing Criteria NFPA 13, Chapters 12 thru 20— Density / Area Design The TYCO Model EC-25 Extended Coverage Upright Sprinklers (TY9128) are UL and C-UL Listed for installation in accordance with the extended cov- erage upright spray sprinkler require- ments of NFPA 13 or other applicable NFPA standards when used in conjunc- tion with the following guidelines: Suitable for the protection of extra hazard and high-piled storage occupancies where area/density design criteria are provided Suitable for unobstructed or noncombustible obstructed construction The Model EC-25 Sprinklers having been specifically tested and Listed for noncombustible obstructed construction are suitable for use within trusses or bar joists having noncombustible web members greater than 1 inch (25,4 mm) when applying the 4 times obstruction criteria rule defined under Obstruc- tions to Sprinkler Discharge Pattern Development." The maximum coverage area per sprinkler is 196 ft.2 (18,2 m2). The maximum distance between sprinklers is 15 feet (4,6 m) when the coverage area does not exceed 144 ft.2 (13,4 m2), and the maximum distance between sprinklers is 14 feet (4,3 m) when the coverage area does not exceed 196 ft2 (18,2 m2). The minimum distance between sprinklers is 8 feet (2,44 m). The minimum flow requirement is based on the design density applied over the actual coverage area per sprinkler. For example: when sprinkler spacing is 14 ft. x 12 ft. -6 in. (4,3 m x 3,8 m) or 175 ft2 (16,3 m2), and the design density is 0.6 gpm/ft.2 (24,4 mm/mm), the sprinkler design flow rate is 105 gpm (397 1pm) and the required design pressure is 17.4 psi (1,2 bar). The minimum clearance between the deflector and the top of storage is 36 inches (0,9 m). For clearances of 36 inches (0,9 m) up to 48 inches (1,21 m), the minimum design pressure is 22 psi (1,52 bar). For clearances of 48 inches (1,21 m) and greater, the minimum design pressure is estab- lished by the minimum flow require- ment. However, the pressure can never be less than 7 psi (0,5 bar). Ordinary and intermediate temper- ature rated Model EC-25 Sprin- klers have been investigated for use in high-piled storage occu- pancies at the hydraulic demand normally associated with high temperature sprinklers. As such, the Model EC-25 Sprinklers are listed storage sprinklers having a K-factor greater than 11.2 (161,4) and having ordinary and interme- diate temperature ratings (i.e., 165°F or 74°C and 214°F or 101eC). Conse- quently, the Model EC-25 Sprin- klers, in accordance with NFPA 13, may be used in conjunction with the density curves for high temperature sprinklers. NFPA obstruction rules for Extended Coverage Sprinklers must be utilized. System Type Wet pipe, dry pipe, and preaction systems are acceptable. FM Approval Criteria FM Loss Prevention Data Sheets 2-0, 3-26, and 8-9 TYCO Model EC-25 Extended Cover- age 25.2K Upright Sprinklers (1Y9128) are FM Approved to be utilized in accor- dance with the following guidelines. Application The Model EC-25 Extended Cov- erage Upright Sprinklers are FM Approved ceiling-level Storage Sprinklers for storage occupancy hazards and other similar high heat release type fires. When compared with other FM Approved Storage Sprinklers, the Model EC-25 Sprinkler provides low hydraulic demand, the spacing advan- tages of extended coverage, and the FM Global obstruction benefits of an upright sprinkler. Model EC-25 Sprinklers should be used in conformance with applicable FM Global Property Loss Prevention Data Sheets. ICH SS TFP2I3 Page 3 of 4 Hydraulic Design To determine the hydraulic design for the Model EC-25 Sprinkler refer to the applicable FM Global Property Loss Prevention Data Sheet. System Type Wet pipe systems only Sprinkler Spacing The maximum coverage area per sprinkler is 196 ft.2 (18,2 m2). The minimum coverage area per sprinkler is 100 ft.2 (9,3 m2). The maximum distance between sprinklers is 14 feet (4,3 m). The minimum distance between sprin- klers is 10 feet (3,05 m). Note: When a wall or obstruction makes a minimum spacing of 10 feet (3,05 m) impossible, consult FM Global Property Loss Prevention Data Sheet 2.0 for applicable guidelines. Sprinkler Location Locate sprinklers with respect to the ceiling/roof in accordance with FM Global Property Loss Prevention Data Sheet 2.0. Obstructions Follow the obstruction requirements as detailed in FM Global Property Loss Prevention Data Sheet 2.0. Other Details All other design details should be in accordance with FM Global Property Loss Prevention Data Sheet 2.0 as well as any other applicable FM Global Data Sheet. NFPA 13, Chapter 21 - Alternative System Design (CMSA) TYCO Model EC-25 Extended Cover- age Upright Sprinklers (TY9128) have successfully undergone large-scale fire tests at FM Global to comply with Chapter 21 of NFPA 13, 2013 Edition. As such, Tables 21.2.2 and 21.3.2 of NFPA 13 may be utilized for design options with the Model EC-25 Upright Sprinklers for providing ceiling-only protection. This allows for the protection of Pal- letized, Solid Piled, Bin Box, Shelf, or Back-to-Back Shelf Storage as well as Single, Double, and Multiple Row Open Rack protection of up to 30 feet (9,1 m) of Cartoned Unexpanded Group A Plastic Commodities in a maximum 35 feet (11 m) ceiling condition with extended spacing up to 196 ft.2 while maintaining very reasonable flow and pressure requirements. Pipe sizes as well as water supply requirements can now be kept to a minimum when compared to other design methods for high piled storage challenges. Refer to Tables A and B of this data sheet for specific flow, pressure, and number of sprinklers to be calculated. When used in accordance with NFPA Chapter 21, smoke vents and draft cur- tains are not required as specified in the 2015 edition of the International Building Code (IBC) and International Fire Code (IFC) for CMSA sprinklers with an RTI of 50 or less and a design of 12 or fewer sprinklers. Construction Type In accordance with NFPA 13 for Extended Coverage Sprinklers for High Piled Storage. Obstruction Criteria Follow Sections 8.8.5.1, 'Extended Coverage Obstruction Guidelines for Sprinkler Discharge Pattern Develop- ment"; 8.12.5.2 and 8.12.5.3, "ESFR Obstruction Criteria," for obstructions that prevent the pattern from reaching the hazard below. Exception: When using the Upright EC-25 Sprinkler, any continuous obstruction 4 inches (100 mm) or less shall be permitted to be ignored in accordance with NFPA 13, section 21.5.3.2.3. Deflector Distance below Ceiling Follow NFPA 13, Section 8.8.4 for allowed deflector distances below ceiling. Clearance to Storage Minimum 36 inches from deflector to top of storage required. Maximum Distance between Sprinklers 14 feet (4,3 m) Minimum Distance between Sprinklers 10 feet (3,0 m) °ITrIMl TOWARDS SPRINKLER FITTING FIGURE 2 W-TYPE I SPRINKLER WRENCH Installation TYCO Model EC-25 Extended Cover- age 25.2K Upright Sprinklers are to be installed in accordance with this section. Damage to the fusible Link Assembly during installation can be avoided by handling the sprinkler using only the frame arms and the appropriate sprin- kler wrench. Do not grip or apply any force to the fusible Link Assembly. Damaged sprinklers must be replaced immediately. A leak-tight 1 inch NPT sprinkler joint should be obtained by apply- ing a minimum-to-maximum torque of 20 to 30 lbs-ft. (26,8 to 40,2 Nm). Higher levels of torque may distort the sprinkler inlet with consequent leakage or impairment of the sprinkler. Note: Install the Model EC-25 Upright Sprinkler in the upright position. Step 1. With pipe thread sealant applied, hand-tighten the sprinkler into the sprinkler fitting. Do not apply any force to the Link Assembly, and handle the Model EC-25 Sprinkler only by the Frame arms. Step 3. Wrench-tighten the Model EC-25 Sprinkler using only the W-Type 1 Sprinkler Wrench (Ref. Figure 2) and by fully engaging (seating) the wrench on the sprinkler wrench flats. Step 4. After installation, inspect the Link Assembly of each Model EC-25 Sprinkler for damage. In particu- lar, verify that the Link Assembly and Hook are positioned as illustrated in Figure 1, and that the Link Assembly has not been bent, creased, or forced out of its normal position in any way. Damaged sprinklers must be replaced immediately. TFP2I3 Page 4 of 4 Max. Ceiling/ Mm. Max. Hose Water Storage Commodity Storage Height Roof Type of Number of Design Operating Pressure Coverage Area Stream Allowance Supply Arrangement Class Feet Height System Sprinklers psi Ft. x Ft. gpm Duration (m) Feet (m) (bar) (m x m) (1pm) Hours 25 30 Wet 6 30 14x14 250 Palletized, Class I thru (76) (91) (2,1) (4,3 x 4,3) (950) Solid-Piled, Class IV, encapsulated Bin Box, Shelf, or and unencapsulated, 30 (9, 35 (11) Wet 8 40 (2,8) 12 x 12 (3,7 x 3,7) 250 (950) Back-to-Back and cartoned non-expanded Shelf Storage plastics 30 35 Wet 8 40 14x14 500 1.5 (9,1) (11) (2,8) (4,3x4,3) (1900) TABLE A NFPA 13, CHAPTER 21—ALTERNATIVE SYSTEM DESIGN PALLETIZED, SOLID-PILED, BIN BOX, SHELF, OR BACK-TO-BACK SHELF STORAGE OF CLASSES I - IV AND CARTONED NON-EXPANDED PLASTIC COMMODITIES Max Max. Ceiling/ Mm. Max. Hose Water Storage Commodity Storage Height Roof Type of Number of Design Operating Pressure Coverage Area Stream Allowance Supply Arrangement Class Feet Height System Sprinklers psi Ft. x Ft. gpm Duration (m) Feet (m) (bar) (mxm) (1pm) Hours 25 30 Wet 6 30 14x14 250 Class I thru (7,6) (9,1) (2,1) (4,3x4,3) (950) Sprinkler protection Class IV, encapsulated 30 35 Wet 8 40 12 x 12 250 criteria for open-frame and unencapsulated, (911) (11) (2,8) (3,7 x 3,7) (950) rack storage and cartoned non- expanded plastics 30 35 Wet 8 40 14 x 14 500 1.5 (911) (11) (2,8) (4,3x4,3) (1900) TABLE B NFPA 13, CHAPTER 21—ALTERNATIVE SYSTEM DESIGN OPEN-FRAME RACK (SINGLE, DOUBLE, AND MULTIPLE ROW) STORAGE OF CLASSES! - IV AND CARTONED NON-EXPANDED PLASTIC COMMODITIES Care and Maintenance TYCO Model EC-25 Extended Cover- age 25.2K Upright Sprinklers must be maintained and serviced in accordance with this section. Before closing afire protection system main control valve for maintenance work on the fire protection system that it controls, obtain permission to shut down the affected fire protection system from the proper authorities and notify all personnel who may be affected by this decision. Inspection, testing, and maintenance must be performed as indicated below and in accordance with the local requirements and/or national codes. Any impairment must be immediately corrected. The owner is responsible for the inspec- tion, testing, and maintenance of their fire protection system and devices in compliance with this document, as well as with the applicable standards of any authorities having jurisdiction. Contact the installing contractor or product manufacturer with any questions. Automatic sprinkler systems are rec- ommended to be inspected, tested, and maintained by a qualified Inspec- tion Service in accordance with local requirements and/or national codes. Limited Warranty For warranty terms and conditions, visit www.tyco-fire.com. Ordering Procedure Contact your local distributor for avail- ability. When placing an order, indicate the full product description and part number (P/N). Sprinkler Assemblies Specify: Model EC-25 Extended Cover- age 25.2K Upright Sprinklers (TY9128), (specify temperature rating), with Natural Brass finish, P/N (specify): 165°F (74°C) ..............PIN 58-450-1-165 212°F (100°C) ............P/N 58-450-1-214 Special Order Sprinkler Assemblies with ISO 7-R 1 Thread Connection Specify: Model EC-25 Extended Cover- age 25.2K Upright Sprinklers (TY9128) with ISO 7-R 1 thread connection, (specify temperature rating), with Natural Brass finish, P/N (specify): 165°F (74°C) ...............PIN 58-451-1-165 212°F (100°C) .............P/N 58-451-1-214 Sprinkler Wrench Specify W-Type 1 Sprinkler Wrench, P/N 56-872-1-025 GLOBAL HEADQUARTERS 11400 Pennbrook Parkway, Lansdale, PA 19446 I Telephone +1-215-362-0700 Copyright © 2015 Tyco Fire Products, LP. All rights reserved. tyco TEFLON is trademark of DuPont corporation. Fire Protection Products Victaulic® Flexible Coupling Style 75 Exaggerated for clarity Approvals/Listings See Victaulic publication 10.01 for details See Victaulic publication 02.06 for portable water approvals if applicable Jtauuic 06.05 I A WARNING 1 Victaulic RX roll sets must be used when grooving light-wall/thin-wall stainless steel pipe for use with Victaulic Couplings. Failure to use Victaulic RX roll sets when grooving light-wall/thin-wall stainless steel pipe may cause joint failure, resulting in serious personal injury and/or NOTICE Victaulic RX grooving rolls must be ordered separately. They are identified by a silver color and the designation RX on the front of the roll sets. Product Description Style 75 is available where moderate pressures are expected or weight considerations are a factor. Up to 50% lighter in weight than the Style 77, the Style 75 coupling is recommended for service up to 500 psi/3450 kPa depending on size. Housings are cast in two identical pieces in all sizes. Hot-dip galvanized and special coatings are available for all sizes. The Victaulic standard flexible coupling offering for grade "EHP" or '1" gaskets is the Style 177 installation-ready flexible coupling. For all available sizes, the Style 177 is the standard flexible coupling Victaulic supplies in North America for piping systems using Grade 'EHP" or "T" gaskets. Contact Victaulic for further details. Performance data presented in this document is based on use with standard wall, carbon steel pipe. For use with stainless steel pipe, please reference publication 17.09 for pressure ratings and end loads. When used on light wall stainless steel pipe, the Victaulic RX roll set must be used to roll groove the pipe. For further information regarding roll grooving stainless steel, refer to publication 17.01. Job/Owner Engineer System No. . Spec Section Location Paragraph Contractor Approved Submitted By Date Date victaulic.com I Couplings I Flexible I Style 75 I Publication 06.05 06.05 1470 Rev 0 updated 09/2014 © 2014 Victaulic company. All rights reserved. 1 ictaulic victaulic.com I Couplings I Flexible I Style 75 I Publication 06.05 Material Specifications Housing: Ductile iron conforming to ASTM A-536, grade 65-45-12. Ductile iron conforming to ASTM A-395, grade 65-45-15, is available upon special request. Housing Coating: (specify choice) Standard: Orange enamel. fl Optional: Hot dipped galvanized and others. Gasket: (specify choice') NOTE: Additional gasket styles are available, contact Victaulic for details. 171 Grade "E" EPDM EPDM (Green stripe color code). Temperature range —30°F to +230°F/-34°C to +110°C. May be specified for cold and hot water service within the specified temperature range plus a variety of dilute acids, oil-free air and many chemical services. UL Classified in accordance with ANSI/NSF 61 for cold +730F/+230C and hot +180°F/+820C potable water service and ANSI/NSF 372. NOT COMPATIBLE FOR PETROLEUM SERVICES. Fl Grade "1" Nitrile Nitrile (Orange stripe color code). Temperature range 20°F to +180°F/29°C to +82°C. May be specified for petroleum products, air with oil vapors, vegetable and mineral oils within the specified temperature range. Not compatible for hot water services over +150°F/+66°C or for hot dry air over +140°F/+600C. 1 Services listed are General Service Guidelines only. It should be noted that there are services for which these gaskets are not compatible. Reference should always be made to the latest Victaulic Gasket Selection Guide for specific gasket service guidelines and for a listing of services which are not compatible. Bolts/Nuts: Heat-treated plated carbon steel, trackhead meeting the physical and chemical requirements of ASTM A-449 and physical requirements of ASTM A-183 06.05 1470 Rev 0 Updated 09/2014 © 2014 Victaulic company. All rights reserved. victaulic.com 2 JtuIicr victautic.com I Couplings I Flexible I Style 75 I Publication 06.05 Dimensions Style 75 too O I li ff IEJ Actual Maximum Maximum Allow. Dimensions Approx. Nominal Outside Working End Pipe End Deflection from Weight Size Diameter Pressure 2 Load 2 Separation3 Centerline3 Bolt/Nut4 X V Z Each Pipe inches inches psi lbs. inches Per Cplg. inches/ft. inches inches inches lbs. mm mm kPa I N mm Degrees mm/rn I (No.) size inches mm mm mm kg 1 1.315 500 680 0-0.06 20-43' 0.57 2-3/ax2 2.38 4.27 1.77 1.3 25 33.4 3450 3025 0-1.6 48 61 108 45 0.6 1 1/4 1.660 500 1080 0-0.06 20-1 ' 0.45 2-3/ox2 2.68 4.61 1.77 1.4 32 42.2 3450 4805 0-1.6 38 68 117 45 0.6 1 1/2 1.900 500 1420 0-0.06 10-56' 0.40 2-3/ax2 2.91 4.82 1.77 1.5 40 48.3 3450 6320 0-1.6 33 74 122 45 0.6 2 2.375 500 2215 0-0.06 1-3 1' 0.32 2-3/sx2 3.43 5.22 1.88 1.7 50 60.3 3450 9860 0-1.6 26 1 87 133 48 0.8 2 1/2 2.875 500 3245 0-0.06 11-115,S' 0.26 2-3/sX2 3.88 5.68 1.88 1.9 65 73.0 3450 14440 0-1.6 22 98 144 48 0.9 76.1 mm 3.000 500 3535 0-0.06 1°-12' 0.26 2-3,kx2 4.00 5.90 1.88 1.9 76.1 3450 15730 0-1.6 22 102 150 48 0.9 3 3.500 500 4800 0-0.06 10-2' 0.22 2-½x2~ 4.50 7.00 1.88 2.9 80 88.9 3450 21360 0-1.6 18 114 178 48 1.3 3½ 4.000 500 6300 0-0.06 0.19 5.00 7.50 1.88 2.9 0°-54' 2-½x2% 90 101.6 3450 28035 0-1.6 16 ___ 127 191 48 1.3 4 4.500 500 7950 0-0.13 10- 36 0.34 2-'/2x2~ 5.80 8.03 2.13 4.1 100 114.3 3450 35380 0-3.2 28 147 204 54 1.9 108.0 mm 4.250 450 6380 0- 0.13 1°-41' 0.35 2-12x70 5.55 7.79 2.13 3.7 108.0 3100 28395 0-3.2 29 141 198 54 1.7 41/2 5.000 450 8820 0-0.13 0.25 6.13 9.43 2.13 5.5 120 127.0 3100 39250 0-3.2 - 10 26' 21 2-Vax3¼ 156 240 54 2.5 5 5.563 450 10935 0-0.13 1°-18' 0.27 2-%x3¼ 6.88 10.07 2.13 5.8 125 141.3 3100 48660 0-3.2 23 175 256 54 2.6 133.0 mm 5.250 450 9735 0-0. 13 1°-21' 0.28 2-16x82.5 6.55 9.37 2.13 6.0 133.0 3100 43325 0-3.2 24 166 238 54 2.7 5.500 450 10665 0-0.13 0.28 6.80 9.59 2.13 6.3 139.7 mm - 10 18 2-Vox3¼ 139.7 3100 47460 0-3.2 24 173 244 54 2.9 152.4 mm 6.000 450 12735 0-0. 13 1°-12' 0.21 2-%x3¼ 7.38 10.48 1.88 6.2 152.4 3100 56670 0-3.2 18 187 266 48 2.8 6 6.625 450 15525 0-0.13 - 10 5' 0.23 2-Yex3¼ 8.00 11.07 2.13 7.0 150 168.3 3100 69085 0-3.2 18 203 281 54 3.2 6.250 450 13800 0-0.13 0.24 7.63 10.49 2.13 6.8 159.0 mm - 1 0 9' 2-16x82.5 159.0 3100 61405 0-3.2 20 194 26 1 54 3.1 8 8.625 450 26280 0-0.13 00- 50' 0.18 2-3/4 X4¼ 10.34 13.97 2.13 1 12.4 200 219.1 3100 116945 0-3.2 14 263 355 59 5.6 2 Working Pressure and End Load are total, from all infernal and external loads, based on standard weight (ANSI) steel pipe, standard roll or cut grooved in accordance with Victaulic specifications, contact Victaulic for performance on other pipe. 3 Allowable Pipe End Separation and Deflection figures show the maximum nominal range of movement available at each joint for standard roll grooved pipe. Figures for standard cut grooved pipe may be doubted. These figures are maximums; for design and installation purposes these figures should be reduced by: 50% for 34_3 ½"/20 -90 mm; 25% for 47100 mm and larger. 4 Number of bolts required equals number of housing segments. General Notes Metric thread size bolts are available (color coded gold) for all coupling sizes upon request. Contact Victaulic for details. WARNING: FOR ONE TIME FIELD TEST ONLY, the Maximum Joint Working Pressure may be increased to 11h times the figures shown. 06.05 1470 Rev 0 Updated 09/2014 0 2014 Victaulic Company. All rights reserved. victaulic.com 3 'j(ctauIic victaulic.com I Couplings I Flexible I Style 75 I Publication 06.05 Installation Note Reference should always be made to the 1100 Victaulic Field Installation Handbook for This product shalt be manufactured by Victaulic or to Victaulic specifications. All products the product you are installing. Handbooks are included with each shipment of Victaulic to be installed in accordance with current Victaulic installation/assembly instructions. products for complete installation and assembly data, and are available in PDF format Victaulic reserves the right to change product specifications, designs and standard on our website at www.victaalic.com. equipment without notice and without incurring obligations. Warranty Trademarks Refer to the Warranty section of the current Price List or contact Victaulic for details. Victaulic is registered trademark of Victaulic Company. 06.05 1470 Rev 0 updated 09/2014 © 2014 Victaulic company. All rights reserved. victaulic.com 4 X ___________ Mechanical-I® STYLES 920 AND 920N Victaulic Mechanical-T Outlet provides a direct branch connection at any location a hole can be cut in pipe. The hole is cut oversize to receive a 'holefinder" locating collar which secures the outlet in position permanently. A pressure responsive gasket seals on the pipe O.D. Cross-type connections can be achieved by utilizing two upper housings of the same style and size, with the same or differing branch size connections. NOTE: Style 920 and Style 920N housings cannot be mated to each other to achieve a cross connection. Style 920 and Style 920N Mechanical-T outlets are available with grooved or female threaded outlet. Specify choice on order. Units are supplied painted with plated bolts. Galvanized hous- ings are available, supplied with plated bolts. All sizes of Style 920 and 920N are rated at 500 psi/3450kPa working pressure on Schedule 10 and 40 carbon steel pipe. They may also be used on high density polyethylene or poly- butylene (HOPE) pipe. Pressure ratings on HDPE are dependent on the pipe rating. Contact Victaulic for ratings on other pipe. Style 920 and 920N are not recommended for use on PVC plastic pipe. Standard piping practices dictate that the Mechanical-I Styles 920 and 920N must be installed so that the main and branch connections are a true 90° angle when permanently attached to the pipeline surface. Additionally, the Vic-Tap Ile hole cutting tool, which allows for hole cutting capabilities on pressurized systems, utilizes the Style 920 Mechanical-T in conjunction with the Series 726 Vic-Ball Valve to create the Style 931 Vic-Tap II Mechanical-T unit. See page 8 for further information. * STYLE 920 CROSS PATENTED STYLES 920 AND 920N MATERIAL SPECIFICATIONS Housing/Coating: Ductile iron conforming to ASTM A-536, grade 65-45-12, with orange enamel coating. Ductile iron conforming to ASTM A-395, grade 65-45-15, is available upon special request. Optional: Hot dipped galvanized Gasket: (Specify choice*) Grade E" EPDM EPDM (Green color code). Temperature range —30°F to +230°F/-34°C to +110°C. Recommended for cold and hot water service within the specified temperature range plus a variety of dilute acids, oil-free air and many chemical services. UL Classified in accordance with ANSI/NSF 61 for cold +86°F/+30°C and hot +180°F/+82°C. NOT RECOMMENDED FOR PETROLEUM SERVICES. Grade T" nitrile Nitrile (Orange color code). Temperature range —20°F to +180°F/-29°C to +82°C. Recommended for petroleum products, air with oil vapors, vegetable and mineral oils within the specified temperature range. Not recommended for hot water services over +150°F/+66°C or for hot dry air over +140°F/+60°C. *Services listed are General Service Recommendations only. It should be noted that there are services for which these gaskets are not recommended. Reference should always be made to the latest Victaulic Gasket Selection Guide for specific gasket service recommendations and for a listing of services which are not recommended. Bolts/Nuts: Heat-treated plated carbon steel, trackhead meeting the physical and chemical requirements of ASTM A-449 and physical requirements of ASTM A-183. JOB/OWNER CONTRACTOR ENGINEER System No, Submitted By Spec Sect Para__________ Location Date . Approved www.victaulic.com vicTAuLic IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2012 vIclAuLic COMPANY. ALL RIGHTS RESERVED. REV_M J'itauIic' 11.02_i CARBON STEEL PIPE - HOLE CUT PRODUCTS 11.02 Mechanical-I® Bolted Branch Outlets STYLES 920 AND 920N 'The Style . Max.Work .11DTTEi.i,i. an~ MID 71 2 ½ ( 920N 2.00 1.50 I 200 2.53 1.61 5.35 275 3.1 0 15 3450 38.1 51 64 - 41 135 70 1.5 - 500 1.50 1.97 2.53 161 5.35 2.75 3.1 20 3450 38.1 50 64 - 41 135 70 1.5 - 1 920N 500 3450 1.50 38.1 1.85 47 2.53 64 - 1.61 41 5.35 136 2.75 70 3.0 1.4 - 1 V (a) 920N 500 1.75 2.05 2.75 3:00 1.61 5.35 3.00 3.5 3.2 - 2 3450 44.5 52 70 76 41 136 76 1.7 1.5 1 ( lt 920 N 500 1.75 2.03 2.75 .3.12 1.51 5.35 3.25 3.6 3.2 0 3450 44.5 52 70 79 41 136 83 1.7 1.5 ½ 920N 500 1.50 2.21 2.74 1.82 5.64 2.75.3.0 3450 38.1 56 .70 46 143 1 70 1.4 - 920N 500 1.50 2.18 2.74 1.82 5.64 2.75 3.0 3450 38.1 55 70 - 46 143 70 1.4 - 1)) 92 500 1.50 2.06 2.74 1.82 5.64 2.75 2.9 25 3450 38.1 52 70 46 143 70 1.4. - I A 0(a) 0 920N 500 1.75 2.30 3.00 3.25 1.82 6.29 3.00 3.5 3.2 32 3450 44.5 58 76 83 46 160 . 76 .1.7 1.5 1 (4 920N3450 500 2.00 2.28 3.00 3.25 1.82 . 6.26 125 3.6 3.3 . 50.8 58 76 1 83 46 159 83 1.7 1.6 2 N o 300 1.50 2.22 2.75 2.25 6.46 .3.18 3.9 2065 38.1 56 70 - 57 164 81 1.8 920N 300 1.50 2.19 2.75 2.25 6.46 3.18 3.9 2065 38.1 55 . 70 57 .164 81 . 1.8 - 1(a) . 920N 300 1.50 2.07 2.75 2.25 6.46 3.18 3.8 2065 38.1 53 70 - 57 164 .81 1.7 lA (a) 920N 500 1.75 .2.30 3.00 3.31 1.92 6.29 3.00 3.5 3.2 32 3450 44.5 58 76 84 49 150 76 .1.6. 1.5 1½ Wf 920N 500 2.00 2.28 300 3.31 1.92 5.29 3.25 3.5 33 0 ' - 3450 50.8 58 76 84 49 150 83 1.6 1.5 920N 500 1.50 2.52 3.05 2.28 6.15 2.75 3.4 0 1 3450 38.1 64 78 - 58 156 70 . 1.6 - /0 a 204 920 N 500 1.50 2.49 305 2.28 6.15 2.75 3.4 3450 38.1 63 78 - 58 156 70 16 - 1 a) 920N 500 1.50 2.38 3.06 . 2.28 6.15 2.75 3.3 3450 38.1 51 78 - 58 156 70 1.6 - 1 V ( )-l-A 920N 500 1.75 .2.55 3.25 3.55 228 6.15 3.00 3.8 37 3450 44.5 65 83 90 58 156 75 1.8 1.8 1 ( ) -ta 920N 500 2.00 2.78 3.50 3.56 2.28 6.15 3.25 4.1 3.8 0(b) 3450 50.8 71 89 90 58 156 83 1.9 . 18 (a) 920N 500 2.50 2.75 3.50 3.56 2.28 675 3.88 49 4.6 5O, 3450 53.5 70 89 90 58 172 99 2.3 2.1 ½ 2 920N 500 2.50 3.00 - 3.75 2.44 6.72 3.88 - 3.8 90 5O 3450 63.5 76 95 62 171 I I 1.8 TABLE CONTINUED ON PG ,3 Center of run to engaged pipe end, female threaded outlet only (dimensions approximate). t Available with grooved or female threaded outlet. Specify choice on order. * Center of run to end of fitting. 8 Female threaded outlets are available to NPT and BSPT specifications. @ See page 7 for Fire Protection approvals and pressure ratings. (a) British Standard female pipe threaded outlet is available as listed. Specify 'BSPT' clearly on order. (b)For 76.1 mm threaded outlet, specify 21/2" BSPT clearly on order. § Vds approved for fire protection services . LPCB approved for fire protection services 0 Approved for use in China by.Tianjin Approvals Company. DIMENSIONS Y z GROOVED OUTLET FV, T 4 W FEMALE THREADED OUTLET Provides a direct branch connection at any location where a hole can be cut in the pipe A pressure responsive gasket provides the seal Request Publication 11.03 for Mechanical-T cross assemblies Pressure rated up to 500 psi/3450 kPa on steel pipe; also available for use with HDPL pipe Sizes from 2 x ½'750 x 15 mm through 8 x 4/200 x 100 mm IMPORTANT NOTES: Style 920 and Style 920N housings cannot be mated to one another to achieve cross connections. www.victaulic.com taulid . vicTAuLic IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 02012 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 11.02_2 . REV_M CARBON STEEL PIPE - HOLE CUT PRODUCTS Mechanical-I® Bolted Branch OUtlets STYLES 920 AND 920N Dimensions mm ML ML _r + cJTABLE CONTINUEbFROMPAGE.2 4 .8 920N 500 I 1.50 3.03 3.56 2.69 7.01 2.75 37 100 5l1i 3450 38.1 77 - 90 - 68 178 70 1.8 - 920N 500 1.50 3.00 3.56 269 7.01 2.75 3.7 20 3450 38.1 76 - 90 - 68 178 70 IS - 1 2 N 500 9 0 1.50 2.88 3.56 269 7.01 2.75 3.6 2 3450 38.1 73 90 68 178 70 1.8 1.75 3.08 3.78 4.00 2.69 7.01 3.00 4.0 3.6 1 ½ ) tp 920N 500 (b) - 3450 44.5 78 96 102 68 178 76 1.9 1.8 1 () tO 92ON 500 2.00 3.28 4.00 4.00 269 7.01 3.25 4.2 3.9 3450 50.8 83 102 102 68 178 83 - 2.0 1.9 920N 500 . 2.50 3.25 4.00 4.00 2.69 7.01 3.88 5.0 4.6 504 -3450 63.5 - 83 102 102 68 178 99 ° 2.3 2.1 920 500 2.75 2.88 4.00 4.00 2.69 7.34 4.63 5.8 5.0 3450 69.9 73 .102 -102 . 68 . 186 118 2.6 .2.3 ol, 7 1 ' 920 500 2.75 2.88 - 4.00 2.69 7.34 4.63 6.4 3450 69.9 73 . - 102 68 186 118 2.9 - 920 500 3.50 3.31 4.50 4.12 2.69 7.73 5.12 8.4 - 6.4 80 3450 88.9 84 114 105 68 196 130 3.8 2.9 1080 1 ' 920N 500 1.75 3.08 3.78 2.63 7.64 3.05 -5.0 - 3450 44.5 78 96 - 67 194 78 2.3 - - . 1 ½ 920N 500 2.00 3.28 4.00 2.63 7.64 3.25 5.0 0 3450 50.8 1 83 102 - 67 194 83 - 2.3 1 - 920N 500 2.50 3.25 4.00 2.63 7.64 4.00 4.0 0 - 3450 63.5 83 102 - 67 194 102 1.9 -. 0 500 2.75 2.88 - 4.00 4.00 2.63 7.64 4.29 8.0 7.8 '1 3450 699 73 102 102 67 194 109 3.6 3.5 ° 920 500 - 3.50 331 4.50 4.50 2.63 7.63 4.88 6.8 6.5 "80"o 3450 88.9 - 84 - 114 114 67 194 124 - 3.1 3.0 1½ ( a) ,t, 920 500 2.00 - 4.03 4.75 4.75 3.16 9.70 3.69 7.4 7.6 o 3450 50.8 102 121 121 1 80 246 94 3.4 3.4 .2(J)ti 920 500 2.50 4.00 4.75 4.75 3.16 9.70 4.38 8.2 8.0 0 3450 63.5 102 121 121 80 246 111 3.7 3.6 ½ )°f 920 500 2.75 3.63 . 4.75 4.75 3.16 9.70 463 8.3 7.9 3450 69.9 92 121 121 80 246 118 3.8 3.6 7 1 m 920 500 2.75 3.75 4.75 3.16 9.70 4.63 8.0 - 3450 .69.9 - 95 - . 121 80 246 118 - 3.6 920 500 3.50 381 5.00 4.63 316 9.70 5.31 84 8.8 0 3450 889 97 127 118 80 246 135 3.8 4.0 0 211,920N 500 250 3.75 4.50 3.17 800 3.88 8.0 - 0 3450 635 95 114 - 81 1 203 1 99 3.6 - 920 500 3.50 3.81 5.00 3.00 1 9.46 1 5.31 80 80, 3450 88.9 97 127 - 76 240 135 3.6 - - )8IIAIIII ILE COI INUED OWP&I4 DIMENSIONS -Y r-r_ z :-11 -v IR O.-I-Viv GROOVED OUTLET _ FEMALE THREADED OUTLET Provides a direct branch connection at any location where a hole can be cut in the pipe A pressure responsive gasket provides the seal .. Request Publication 11.03 for Mechanical-I cross assemblies Pressure rated up to 500 psi/3450kPa on steel pipe; also available for use with HDPE pipe Sizes from 2 x ½'/50 x 15mm through 8 x 4/200 x 100 mm IMPORTANT NOTES: Center of run to engaged pipe end, female threaded outlet only (dimensions approximate). Style 920 and Style 920N housings cannot be t Available with grooved or female threaded outlet. Specify choice on order. mated to one another - * Center of run to end of fitting. to achieve cross connections. # Female threaded outlets are available to NPT and. BSPT specifications. @ See page 7 for Fire Protection approvals and pressure ratings. (a) British Standard female pipe threaded outlet is available as listed. Specify BSPT' clearly on order. (b)For 76.1 mm threaded outlet, specify 21h" BSPT clearly on order. § Vds approved for fire protection services a LPCB approved for fire protection services - 0 Approved for use in China by Tianjin Approvals Company. www.victaulic.com vIcTAuLIc is A REGISTERED TRADEMARK OF ViTALiC COMPANY. 02012 VICTAULiC COMPANY. ALL RIGHTS RESERVED. Is" 4-c-t a -U1 ii d REV_M . 11.02_3 CARBON STEEL PIPE - HOLE CUT PRODUCTS 11.02 Mechanical-TO Bolted Branch Outlets STYLES 920 AND 920N DIMENSIONS loan "M t II GROOVED OUTLET FEMALE THREADED OUTLET Provides a direct branch connection at any location where a hole can be cut in the pipe A pressure responsive gasket provides the seal Request Publication 11.03 for Mechanical-T cross assemblies Pressure rated up to 500 psi/3450 kPa on steel pipe; also available for use with HDPE pipe Sizes from 2.x ½750 x 15 mm through 8 x 4/200 x 100mm. IM P0 RTA NT NOTES: Style 920 and Style 920N housings cannot be mated to one another to achieve cross connections. Dimensions Hole Inc!e es v' Inches .0.13 Inches Inches Inches Inches Inches Inche 920N 500 20013.78450 330 8.23 3450 50.8 96 114 - 84 209 83 3.2 - 920N 500 2.50 3.75 4.50 330 8.23 3.88 9.0 3450 63.5 95 114 - 84 209 99 41 - 920N 500 1.75 4.43 5.13 5.13 379 9.15 3.25 51 4.8 - .(b) '. 3450 44.5 112 130 130 96 232 83 2.3 2.2 (a)'ta 500 2.00 4.40 5.13 5.13 3.79 9.15 3.25 5.4 5.1 40 (ii~3450 920N 50.8 112 130 . 130 96 232 .83 2.4 2.3 920N 500 2.50 4.38 5.13 5.13 3.79 9.15 3.88 6.0 5.6 .0 3450 63.5 111 130 130 96 232 99 2.7 2.5 2 V,920 500 2.75 4.01 5.13 5.12 3.69 10.51 4.63 8.3 7.6 .- 3450 69.9 110 130 130 94 267 118 3.8 3.4 M 920 500 2.75 4.15 5.21 3.69 10.51 4.63 8.4 3450 69.9. 105 - 132 94, 267 118 - .3.8 500 3.50 4.31 5.50 5.13 3.69 10.51 5:31 9.9 8.4 - 920 3450 88.9 110 140 130 94 267 135 4.5 3.8 - '11 . 920 500 4.50 3.81 5.75 5:38 3.69 10.51 6.25 10.1 10.1 'OC 3450 114.3 97 146 137 94 267 159 4.6 4.6 500 2.00 4.41 5.13 3.63 9.40 3.25 7.8' 159 O . -It 920N 3450 50.8 112 130 - .92 239 83 3.5 - Dl 920N 500 2.50 4.38 5.13 3.63 9.40 3.88 8.0 3450 63.5 111 130 - 92 239 99 3.6 76 920 500 2.75 4.38 5.50 5.13 3.63 9.40 4.63 9.5 9.5 - m,m 3450 69.9 111 140 130 1 92 239 118 4.3 4.3 500 3.50 4.31 5.50 5.13 3.63 9.40 5.31 8.1 14.0 - - Rf 920 3450 88.9 110 140 130 92 239 135 .3.7 6.4 920 500 50 4.45 5.38 3.63 9.40 - 6.12 10.0 - 10 3450 1143 113 - 137 92 239 155 45 920 500 4.50 3.81 5.75 3.63 9.40 6.25 180 100 3450 114.3 96.80 146 - 92 239 159 8.2 - LECOI NUED' IPG5 "center of run to engaged pipe end, female threaded outlet only (dimensions approximate). t Available with grooved or female threaded outlet. Specify choice on order. * center of run to end of fitting. ff Female threaded outlets are available to NPT and BSPT specifications. @ See page 7 for Fire Protection approvals and pressure ratings. (a) British Standard female pipe threaded outlet is available as listed. Specify "BSPT clearly on order. (b)For 76.1 mm threaded outlet, specify 21/2" BSPT clearly on order. - - § Vds approved for fire protection services o LPCB approved for fire protection services 0 Approved for use in china by Tianjin Approvals Company. www.victaulic.com . . . J1'tauIic VICTAuLIC IS A REGISTERED TRADEMARK OF VICTAuLIC COMPANY. © 2012 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 11.02_4 . REV_M CARBON STEEL PIPE - HOLE CUT PRODUCTS 11.02 Mechanical-I® Bolted Branch Outlets STYLES 920 AND 920N DIMENSIONS GROOVED OUTLET FEMALE THREADED OUTLET Provides a direct branch connection at any location where a hole can be cut in the pipe A pressure responsive gasket provides the seal Request Publication 11.03 for Mechanical-T cross assemblies Pressure rated up to 500 psi/3450 kPa on steel pipe; also available for use with HDPE pipe Sizes from 2 x ½'/50 x 15 mm through 8 x 4/200 x 100 mm 1 . _______Dimensions Hole Vt# VT 1• +0.13 Inches Inches Inches Inches Inches Inches -0.00 min mm mrn mm mm mm TABLE CONTINUED FROM PAGE 4 __ 1651 x 1 920N 500 1.50 3.88 4.56 3.79 9.34 2.75 8.0 25 3450 38.1 99 116 - 96 237 70 3.6 - 1 Au 920N 500 1.75 4.43 5.13 3.79 9.34 3.25 8.4 32 3,450 44.5 113 130 - 96 237 83 3.8 - 500 5.13 5.13 3.79 11/2 (a) to 920N 2.00 4.41 9.34 3.25 8.4 5.4 40 3450 50.8 112 130 130 96 237 83 3.8 2.4 6.0 2(a) t 920N 500 2.50 4.38 5.13 5.13 3.79 9.34 3.88 8.5 50 3450 63.5 111 130 130 96 237 99 3.9 2.7 5.13 5.21 3.63 10.51 761 mm 920 500 2.75 4.01 4.63 8.6 7.6 3450 69.9 110 130 132 92 267 118 3.9 3.4 3 (a) f 0 920 500 3.50 4.31 5.50 5.13 3.63 10.51 5.31 10.2 8.4 80 3450 88.9 110 140 130 92 267 135 4.6 3.8 4 (a) to 920 500 4.50 3.81 5.75 5.38 3.63 10.51 6.25 10.5 8.4 100 920 3450 114.3 97 146 137 92 267 159 4.8 3.8 8 2(a) t 500 2.75 5.44 6.19 6.25 4.81 12.42 4.50 11.6 11.6 200 >< 50 3450 69.9 138 157 159 122 316 114 5.3 5.3 2½ (a) t 920 500 2.75 5.07 6.19 6.19 4.81 12.42 4.50 11.6 11.6 65 3450 69.9 129 157 157 122 316 114 5.3 5.3 11.6 761 mm 920 500 2.75 5.25 6.25 4.81 12.42 4.56 3450 69.9 133 - 159 122 316 116 - 5.3 3(a) to 920 500 3.50 5.31 6.50 6.50 4.81 12.42 5.31 12.6 80 3450 88.9 135 165 165 122 316 135 5.7 5.3 6.38 12.42 4 (a) to 920 500 4.50 4.81 6.75 4.81 6.25 15.3 12.5 100 3450 114.3 122 171 162 122 316 159 6.9 5.7 Center of run to engaged pipe end, female threaded outlet only (dimensions approximate). t Available with grooved or female threaded outlet. Specify choice on order. * Center of run to end of fitting. U Female threaded outlets are available to NPT and BSPT specifications. @ See page 7 for Fire Protection approvals and pressure ratings.' (a) British Standard female pipe threaded outlet is available as listed. Specify BSPT' clearly on order. (b)For 76.1 mm threaded outlet, specify 2W BSPT clearly on order. § Vds approved for fire protection services n LPCB approved for fire protection services 0 Approved for use in China by Tianjin Approvals Company. IMPORTANT NOTES: Style 920 and Style 920N housings cannot be mated to each other to achieve cross connections. www.victaulic.Com 'dicctauIicr VICTAuLIC IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. C 2012 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REV_M 11.02_5 CARBON STEEL PIPE - HOLE CUT PRODUCTS 11.02 Mechanical—I® Bolted Branch Outlets STYLES 920 AND 920N FLOW DATA Flow test data has shown that the total head loss between point (1) and (2) for the Style 920, 920N and 929 Mechanical-TO fittings can best be expressed in terms of the pressure difference across the inlet and branch. The pressure difference can be obtained from the relationship below. Cv and Ky Values Values for flow of water at +60°F/-i-16°C are shown in the table below. Formulas for C5 1K Values: AP = Q Where: = Where: c Q = Flow (GPM) K Q = Flow (m3/h) = Q C x AP = Pressure Drop (psi) = Flow Coefficient = Q X AP = Pressure Drop (bar) = K Flow Coefficient Exaggerated for clarity Equivalent Length of Outlet Size Sc hedule 40 Carbon Steel Pipe OUTLET SIZE (C 1 20)t FT C%JKv Values------- NOMINAL ACTUAL DIAMETER O.D. Inimm in GROOVED THREADED GROOVED THREADED ½ 0.840 I i 11 15 21.3 - 2 9.4 1/4 1.050 16 - - 20 26.7 1.315 13.7 21 1 - 8 - 25 33.7 1.660 50 .1.8 48 11/4 32 42.7 5½ 6 42.9 41.1 1 ½ - 1.900 s - 53 40 98.3 2.375 11 45.4 112 45.4 104 2 50 9 60.3 10½ 119 216 2.875 150 65 73.0 3.000 20 16 12½ 102 161 128.5 76.1 mm 76.1 - 138.1 - 3.500 249 237 80 88.9 4.500 14 15 213.4 421 203.1 401 100 114.3 20 22 360.8 343.6 Hazen-Williams coefficient of friction is 120. Pipe with a wall thickness of 0,165in 14.2mm. www.victaulic.com \1tauIict VICTAuLIc IS REGISTERED TRADEMARK OF viciuic COMPANY. 02012 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 11.02_6 REV_M CARBON STEEL PIPE - HOLE CUT PRODUCTS 11.02 Mechanical-I® Bolted Branch Outlets STYLES 920 AND 920N FIRE PROTECTION APPROVALS AND PRESSURE RATINGS The information provided below is based on the latest listing and approval data at the time of publication. Listings/Approvals are subject to change and/or additions by the approvals agencies. Contact Victaulic for performance on other pipe and the latest listings and approvals. Approval Agency Rated Working Pressures - psi/kPa 21/2 -6 2.875 - 6.625 All 10,40 400 400 400 290 232 362 65-150 73.0-168.3 All DF 2755 300 2755 300 2755 300 1.999 290 1599 232 2496 362 21/2-4 2.875 - 4.500 65-100 73.0-114.3 2.875 - 4.500 All SF 2065 300 2065 300 2065 300 1999 290 1599 232 2496 362 21/2 -4 65-100 73.0-114.3 6.625 3,4 10 2065 300 2065 300 2065 250 1999 290 1599 232 2496 362 6 150 168.3 34 3040 2065 300 2065 1724 1999 1599 2496 6 6.625 300 300 290 232 362 150 168.3 8.625 21/2 ' 10,40 2065 400 2065 2065 1999 1599 145 2496 8 200 219.1 2755 300 - - - 1000 145 - 8 8.625 34 10 250 200 219.1 8.625 — __ 34 f , —- 30 40 2065 300 - 1724 300 - 1000 145 - 8 - 200 219.1 ' 2065 2065 1000 NOTES: 10 refers to Listed/Approved Schedule 10 steel sprinkler pipe. 40 refers to Listed/Approved Schedule 40 steel sprinkler pipe. DF refers to Listed/Approved Dyna-Flow steel sprinkler pipe manufactured by American Tube Company. SF refers to Listed/Approved Super-Flo steel sprinkler pipe manufactured by Allied Tube and Conduit Corporation. VIC-TAP II HOLE CUTTING TOOL FOR The Vic-Tap II hole cutting tool is designed for use with the Style 931 Vic-Tap II Mechanical-T unit, 4 - 8/100 - 200 MM CARBON STEEL PIPE which is a combination of the Style 920 Mechanical-T and Series 726 Vic-Ball Valve. The Vic-Tap II is capable of tapping into carbon steel pipe systems under pressures up to 500 psi/3450 kPa. The Style 931 Vic-Tap II Mechanical-T unit is a full port ball valve which can be mounted on 47100mm, 5/125mm, 6/150mm and 8'/200 mm diameter pipe. The Style 931 comes with a 2½'/65mm grooved outlet. The drill motor is an electric motor with ground fault circuit interrupter (GFCI) in accordance with safety codes. For more information, refer to publication 24.01. www.victaulic.com Idictaulid vlcrAuuc IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2012 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REV_M 11.02_7 Mechanical-I® STYLES 920 AND 920N INSTALLATION Reference should always be made to the 1-100 Victaulic Field Installation Handbook for the product you are installing. Handbooks are included with each shipment of Victaulic products for complete installation and assembly data, and are available in PDF format on our website at www.victaulic.com. WARRANTY Refer to the Warranty section of the current Price List or contact Victaulic for details. NOTE This product shall be manufactured by Victaulic or to Victaulic specifications. All products to be installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations. For complete contact information, visit www.victaulic.com 11.02 1480 REV M UPDATED 03/2012 ictauIic vICTAuLIC IS A REGISTERED TRADEMARK OF VICTALILIC COMPANY. © 2012 vicTAuLic COMPANY. ALL RIGHTS RESERVED. 11.02L