Loading...
HomeMy WebLinkAbout3209 LIONSHEAD AVE; ; FPC2022-0042; PermitPERMIT REPORT Fire Permit Print Date: 03/25/2022 Job Address: Permit Type: Parcel#: Valuation: Occupancy Group: #of Dwelling Units: Bedrooms: Bathrooms: Project Title: 3209 LIONSHEAD AVE, CARLSBAD, CA 92010-4710 FIRE-Construction Commercial Work Class: 2218811500 Track#: $54,881.80 Lot#: Project#: Plan#: Construction Type: Orig. Plan Check#: Plan Check#: Fire Sprinklers Description: PRANA -SPRINKLER Tl & CHANGING WATER SUPPLY FEED (1 HEAD) Applicant: EPIC FIRE PROTECTION INC ADAM BOISVERT 765 TURTLE POINT WAY SAN MARCOS, CA 92069-8126 {760) 310-6122 FEE FIRE NFPA 13 or 13R System 6 heads or less Total Fees: $137.00 Total Payments To Date: Fire Department $137.00 (city of Carlsbad Permit No: FPC2022-0042 Status: Closed -Finaled Applied: 03/03/2022 Issued: 03/18/2022 Finaled Close Out: 03/25/2022 Inspector: Final Inspection: FPContractor: EPIC FIRE PROTECTION INC 765 TURTLE POINT WAY SAN MARCOS, CA 92069-8126 (760} 310-6122 Balance Due: AMOUNT $137.00 $0.00 Page 1 of 1 1635 Faraday Avenue, Carlsbad CA 92008-7314 I 760-602-4665 I 760-602-8561 f I www.carlsbadca.gov Dashbodrd Hydraulics Hydraulics Summary Sheet ,. Project Information __________ ..,.. _____ Calculation Date: 3/1/2022 8:52 AM PRANA UPGRADE PROOF CALC 3209 LIONSHEAD AVE. CARLSBAD, CA contract# Contractor Information ------ EPIC FIRE PROTECTION, INC. 765 TURTLE POINT WAY SAN MARCOS, CA 92069 calculated by ADAM BOISVERT telephone 760-310-6122 fax 760-798-0556 email ADAM@EPICFIRE.ORG Sprinklers in Remote ------- No. Mfgr Mod SIN# Size K 36 TYCO ELO TY5151 .64 11.20 ,,.-- system ID SYS 1 drawing ref 1 OF 1 building EXISTING construction occupancy S, F-1 authority CARLSBAD FIRE Hydraulics Criteria density .525 GPM/ft2 system type WET design std NFPA 13, 2016 remote area ENTIRE ft2 hazard EXTRA spr coverage 80 ft2 sprs flowing 36 figure curve 70 Design Layer 1 -Supply / Demand Graph 65 60 55 50 :::' 45 ti) ~40 Cl) :S 35 ti) u, 30 ~ 0. 25 20 15 10 5 0 Sprinkler Demand of 39.11 psi with Total System Flow of 1,574.9 GPM ~ ~ v----------~ / / 1/ V .,,,. "" 2,074.~ GPM 0 350 700 1050 1400 1750 2100 2450 Water Flow (GPM) e Demand at sprinkler and interior hose flows © Copyright 2016 Sigma Development Group, Inc. ◊ Total System Demand including Hose Flows at Zero N1.85 2800 Page 1 of 11 0880Cf Dashboard Hydraulics Supply Analysis Source Node Sprinkler Flow: Static Pressure Hose Flow at Zero: Residual Pressure No Water Supply 1,574.9GPM 500.0 GPM Quantity Flowing Pressure Available Additional Flows: Total System Flow: Maximum velocity in pipe 0-1 is 15.9 ft/sec Nodes Analysis Minimum Node Actual Node Elev Device KFactor Flow Pressure Discharge ft GPM psi GPM 113 27.00 Sprinkler 11.20 42.00 14.06 42.00 112 27.00 Sprinkler 11.20 42.00 14.07 42.00 120 27.00 Sprinkler 11.20 42.00 14.08 42.03 119 27.00 Sprinkler 11.20 42.00 14.09 42.03 114 27.00 Sprinkler 11.20 42.00 14.09 42.04 121 27.00 Sprinkler 11.20 42.00 14.11 42.07 111 27.00 Sprinkler 11 .20 42.00 14.13 42.10 118 27.00 Sprinkler 11.20 42.00 14.15 42.13 127 27.00 Sprinkler 11 .20 42.00 14.15 42.14 126 27.00 Sprinkler 11.20 42.00 14.16 42.14 128 27.00 Sprinkler 11.20 42.00 14.18 42.17 125 27.00 Sprinkler 11.20 42.00 14.22 42.24 134 27.00 Sprinkler 11 .20 42.00 14.31 42.36 133 27.00 Sprinkler 11 .20 42.00 14.31 42.37 110 27.00 Sprinkler 11 .20 42.00 14.31 42.37 135 27.00 Sprinkler 11.20 42.00 14.33 42.40 117 27.00 Sprinkler 11.20 42.00 14.33 42.40 132 27.00 Sprinkler 11.20 42.00 14.38 42.46 124 27.00 Sprinkler 11 .20 42.00 14.41 42.51 131 27.00 Sprinkler 11.20 42.00 14.57 42.75 109 27.00 Sprinkler 11.20 42.00 14.67 42.90 116 27.00 Sprinkler 11.20 42.00 14.70 42.93 123 27.00 Sprinkler 11.20 42.00 14.77 43.05 130 27.00 Sprinkler 11.20 42.00 14.94 43.29 108 27.00 Sprinkler 11.20 42.00 15.27 43.77 © Copyright 2016 Sigma Development Group, Inc. PRANA UPGRADE PROOF CALC (Design Layer 1) Total ~ystem Flow 2,074.9GPM Total Pressure Required 39.11psi None 2,074.9GPM Notes Page 2 of 11 Nodes Analysis Minimum Node Actual Node Elev Device KFactor Flow Pressure Discharge Notes ft GPM psi GPM 115 27.00 Sprinkler 11.20 42.00 15.30 43.80 122 27.00 Sprinkler 11.20 42.00 15.38 43.93 129 27.00 Sprinkler 11.20 42.00 15.56 44.18 104 27.00 Sprinkler 11.20 42.00 18.04 47.57 105 27.00 Sprinkler 11.20 42.00 18.07 47.61 100 27.00 Sprinkler 11 .20 42.00 18.09 47.64 101 27.00 Sprinkler 11.20 42.00 18.12 47.68 106 27.00 Sprinkler 11.20 42.00 18.18 47.76 102 27.00 Sprinkler 11.20 42.00 18.23 47.83 107 27.00 Sprinkler 11 .20 42.00 18.42 48.07 103 27.00 Sprinkler 11.20 42.00 18.47 48.13 0 0.00 Hose@Zero 39.11 500.0 © Copyright 2016 Sigma Development Group, Inc. Page 3 of 11 08800-Design Layer 1 Dashboard H raulics 13 il 0 0 ..... 12 0 0 11 0 0 ..... 10 © Copyright 2016 Sigma Development Group, Inc. EPIC FIRE PROTECTION, INC. PRANAUPGRADEPROOFCALC 0 0 ..... 0 0 0 0 33 32 31 30 Page 1 of 1 Calculation Results Demand Pressure: 39.11 psi Demand Flow: 2,07 4.9GPM No water supply info available. NotesThere are 28 sprinklers in this remote area. Page 4 of 11 08800- Dashboard Hydraulics Pipe Information From Elev1 Pipe ID Flows ft Added Inside GPM Diameter Fittings To Elev2 Type in ft Total 103 27.00 2½11 Eddy Flow 2.7050 0 107 27.00 BN 48.1 13 27.00 2½ 11 Eddy Flow 48.1 2.7050 2T/2T 103 27.00 BN 96.2 102 27.00 2½ 11 Eddy Flow 2.7050 0 106 27.00 BN 47.8 12 27.00 2½" Eddy Flow 47.8 2.7050 2T/2T 102 27.00 BN 95.6 101 27.00 2½ 11 Eddy Flow 2.7050 0 105 27.00 BN 47.6 11 27.00 2½ 11 Eddy Flow 47.7 2.7050 2T/2T 101 27.00 BN 95.3 100 27.00 2½ 11 Eddy Flow 2.7050 0 104 27.00 BN 47.6 10 27.00 2½ 11 Eddy Flow 47.6 2.7050 2T/2T 100 27.00 BN 95.2 135 27.00 2½" Eddy Flow 2.7050 134 27.00 BL 30.5 33 27.00 2½" Eddy Flow 42.4 2.7050 2T 135 27.00 BL 72.9 © Copyright 2016 Sigma Development Group, Inc. Length Fitting Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total PRANA UPGRADE PROOF CALC (Design Layer 1) ft C Value Total (Pt) psi ft Elev (Pe) psi Notes Friction Loss ft psi/ft Frict (Pf) psi 8.0 C = 120 Pt 107) 18.419 0.0 Pe 0.000 8.0 0.00654 Pf 0.052 4.5 C = 120 Pt 103) 18.471 74.9 Pe 0.000 79.4 0.02360 Pf 1.873 Total Pressure at Node 13) 20.344 psi 8.0 C = 120 Pt 106) 18.183 0.0 Pe 0.000 8.0 0.00646 Pf 0.052 4.5 C = 120 Pt 102) 18.235 74.9 Pe 0.000 79.4 0.02332 Pf 1.851 Total Pressure at Node 12) 20.086 psi 8.0 C = 120 Pt 105) 18.072 0.0 Pe 0.000 8.0 0.00642 Pf 0.051 4.5 C = 120 Pt 101) 18.123 74.9 Pe 0.000 79.4 0.02319 Pf 1.840 Total Pressure at Node 11) 19.964 psi 8.0 C = 120 Pt 104) 18.041 0.0 Pe 0.000 8.0 0.00641 Pf 0.051 4.5 C = 120 Pt 100) 18.093 74.9 Pe 0.000 79.4 0.02315 Pf 1.837 Total Pressure at Node 10) 19.930 psi 8.0 C = 120 Pt 134) 14.306 0.0 Pe 0.000 8.0 0.00282 Pf 0.023 208.0 C = 120 Pt 135) 14.329 37.4 Pe 0.000 245.4 0.01412 Pf 3.465 Total Pressure at Node 33) 17.794 psi Page 5 of 11 D880<f Dashboard Hydraulics Pipe Information From Elev1 Pipe ID Flows ft Added Inside GPM Diameter Fittings To Elev2 Type in ft Total 133 27.00 2½ 11 Eddy Flow 2.7050 134 27.00 BL 11.9 132 27.00 2½ 11 Eddy Flow 42.4 2.7050 133 27.00 BL 54.2 131 27.00 2½ 11 Eddy Flow 42.5 2.7050 132 27.00 BL 96.7 130 27.00 2½ 11 Eddy Flow 42.7 2.7050 131 27.00 BL 139.5 129 27.00 2½" Eddy Flow 43.3 2.7050 130 27.00 BL 182.8 13 27.00 2½" Eddy Flow 44.2 2.7050 2T 129 27.00 BL 226.9 128 27.00 2½ 11 Eddy Flow 2.7050 127 27.00 BL 31.1 32 27.00 2½" Eddy Flow 42.2 2.7050 2T 128 27.00 BL 73.3 126 27.00 2½ 11 Eddy Flow 2.7050 127 27.00 BL 11.0 125 27.00 2½ 11 Eddy Flow 42.1 2.7050 126 27.00 BL 53.1 124 27.00 2½" Eddy Flow 42.2 2.7050 125 27.00 BL 95.4 © Copyright 2016 Sigma Development Group, Inc. Length Fitting Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total ft C Value ft Friction Loss ft psi/ft 8.0 C = 120 0.0 8.0 0.00049 8.0 C = 120 0.0 8.0 0.00818 8.0 C = 120 0.0 8.0 0.02383 8.0 0.0 C = 120 8.0 0.04691 8.0 0.0 C = 120 8.0 0.07735 4.0 C = 120 37.4 41.4 0.11545 PRANA UPGRADE PROOF CALC (Design Layer 1) Total (pt) psi Elev (Pe) psi Notes Frict (Pf) psi Pt 134) 14.306 Pe 0.000 Pf 0.004 Pt 133) 14.310 Pe 0.000 Pf 0.065 Pt 132) 14.376 Pe 0.000 Pf 0.191 Pt 131) 14.566 Pe 0.000 Pf 0.375 Pt 130) 14.942 Pe 0.000 Pf 0.619 Pt 129) 15.560 Pe 0.000 Pf 4.784 Total Pressure at Node 13) 20.344 psi 8.0 C = 120 Pt 127) 14.155 0.0 Pe 0.000 8.0 0.00293 Pf 0.023 208.0 C = 120 Pt 128) 14.178 37.4 Pe 0.000 245.4 0.01427 Pf 3.503 Total Pressure at Node 32) 17.681 psi 8.0 C = 120 Pt 127) 14.155 0.0 Pe 0.000 8.0 0.00043 Pf 0.003 8.0 C = 120 Pt 126) 14.158 0.0 Pe 0.000 8.0 0.00787 Pf 0.063 8.0 C = 120 Pt 125) 14.221 0.0 Pe 0.000 8.0 0.02323 Pf 0.186 Page 6 of 11 08.SO<f Dashboard Hydraulics Pipe Information From Elev1 Pipe ID Flows ft Added Inside GPM Diameter Fittings To Elev2 Type in ft Total 123 27.00 2½11 Eddy Flow 42.5 2.7050 124 27.00 BL 137.9 122 27.00 2½" Eddy Flow 43.0 2.7050 123 27.00 BL 180.9 12 27.00 2½11 Eddy Flow 43.9 2.7050 2T 122 27.00 BL 224.9 121 27.00 2½ 11 Eddy Flow 2.7050 120 27.00 BL 31.4 31 27.00 2½ 11 Eddy Flow 42.1 2.7050 2T 121 27.00 BL 73.5 119 27.00 2½11 Eddy Flow 2.7050 120 27.00 BL 10.6 118 27.00 2½11 Eddy Flow 42.0 2.7050 119 27.00 BL 52.6 117 27.00 2½11 Eddy Flow 42.1 2.7050 118 27.00 BL 94.8 116 27.00 2½" Eddy Flow 42.4 2.7050 117 27.00 BL 137.2 115 27.00 2½ 11 Eddy Flow 42.9 2.7050 116 27.00 BL 180.1 11 27.00 2½ 11 Eddy Flow 43.8 2.7050 2T 115 27.00 BL 223.9 © Copyright 2016 Sigma Development Group, Inc. Length Fitting Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total PRANA UPGRADE PROOF CALC (Design Layer 1) ft C Value Total (Pt) psi ft Elev (Pe) Friction Loss psi Notes ft psi/ft Frict (Pf) psi 8.0 C = 120 Pt 124) 14.407 0.0 Pe 0.000 8.0 0.04594 Pf 0.367 8.0 C = 120 Pt 123) 14.774 0.0 Pe 0.000 8.0 0.07594 Pf 0.607 4.0 C = 120 Pt 122) 15.382 37.4 Pe 0.000 41.4 0.11352 Pf 4.704 Total Pressure at Node 12) 20.086 psi 8.0 C = 120 Pt 120) 14.083 0.0 Pe 0.000 8.0 0.00298 Pf 0.024 208.0 C = 120 Pt 121) 14.107 37.4 Pe 0.000 245.4 0.01435 Pf 3.521 Total Pressure at Node 31) 17.628 psi 8.0 C = 120 Pt 120) 14.083 0.0 Pe 0.000 8.0 0.00040 Pf 0.003 8.0 C = 120 Pt 119) 14.086 0.0 Pe 0.000 8.0 0.00773 Pf 0.062 8.0 C = 120 Pt 118) 14.148 0.0 Pe 0.000 8.0 0.02295 Pf 0.184 8.0 C = 120 Pt 117) 14.332 0.0 Pe 0.000 8.0 0.04548 Pf 0.364 8.0 C = 120 Pt 116) 14.696 0.0 Pe 0.000 8.0 0.07527 Pf 0.602 4.0 C = 120 Pt 115) 15.298 37.4 Pe 0.000 41.4 0.11261 Pf 4.666 Total Pressure at Node 11) 19.964 psi Page 7 of 11 Dashboard Hydraulics Pipe Information From Elev1 Pipe ID Flows ft Added Inside GPM Diameter Fittings To Elev2 Type in ft Total 114 27.00 2½" Eddy Flow 2.7050 113 27.00 BL 31.5 30 27.00 2½" Eddy Flow 42.0 2.7050 2T 114 27.00 BL 73.6 31 27.00 411 Eddy Flow 4.3100 30 27.00 CM2 73.6 32 27.00 4" Eddy Flow 73.5 4.3100 31 27.00 CM2 147.1 33 27.00 4" Eddy Flow 73.3 4.3100 32 27.00 CM2 220.4 34 27.00 411 Eddy Flow 72.9 4.3100 33 27.00 CM2 293.3 112 27.00 2½ 11 Eddy Flow 2.7050 113 27.00 BL 10.5 111 27.00 2½ 11 Eddy Flow 42.0 2.7050 112 27.00 BL 52.5 110 27.00 2½" Eddy Flow 42.1 2.7050 111 27.00 BL 94.6 109 27.00 2½ 11 Eddy Flow 42.4 2.7050 110 27.00 BL 136.9 108 27.00 2½" Eddy Flow 42.9 2.7050 109 27.00 BL 179.9 © Copyright 2016 Sigma Development Group, Inc. Length Fitting Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total ft C Value ft Friction Loss ft psi/ft 8.0 0.0 C = 120 8.0 0.00300 208.0 C = 120 37.4 245.4 0.01437 10.0 C = 120 0.0 10.0 0.00149 10.0 C = 120 0.0 10.0 0.00535 10.0 0.0 C = 120 10.0 0.01131 10.0 C = 120 0.0 10.0 0.01919 PRANA UPGRADE PROOF CALC (Design Layer 1) Total (Pt) psi Elev (Pe) psi Notes Frict (Pf) psi Pt 113) 14.063 Pe 0.000 Pf 0.024 Pt 114) 14.087 Pe 0.000 Pf 3.526 Pt 30) 17.613 Pe 0.000 Pf 0.015 Pt 31) 17.628 Pe 0.000 Pf 0.054 Pt 32) 17.681 Pe 0.000 Pf 0.113 Pt 33) 17.795 Pe 0.000 Pf 0.192 Total Pressure at Node 34) 17.986 psi 8.0 C = 120 Pt 113) 14.063 0.0 Pe 0.000 8.0 0.00039 Pf 0.003 8.0 C = 120 Pt 112) 14.066 0.0 Pe 0.000 8.0 0.00769 Pf 0.062 8.0 C = 120 Pt 111) 14.128 0.0 Pe 0.000 8.0 0.02287 Pf 0.183 8.0 C = 120 Pt 110) 14.311 0.0 Pe 0.000 8.0 0.04535 Pf 0.363 8.0 C = 120 Pt 109) 14.674 0.0 Pe 0.000 8.0 0.07509 Pf 0.601 Page 8 of 11 D8_80<f Dashboard Hydraulics Pipe Information From Elev1 Pipe ID Flows ft Added Inside GPM Diameter Fittings To Elev2 Type in ft Total 10 27.00 2½" Eddy Flow 43.8 2.7050 2T 108 27.00 BL 223.6 11 27.00 611 Sch 10 95.2 6.3570 0 10 27.00 CM1 318.8 12 27.00 6" Sch 10 319.2 6.3570 0 11 27.00 CM1 638.0 13 27.00 6" Sch 10 320.5 6.3570 0 12 27.00 CM1 958.5 6 27.00 6" Sch 10 323.1 6.3570 0 13 27.00 CM1 1,281.6 35 27.00 4" Eddy Flow 4.3100 34 27.00 CM2 241.4 36 27.00 4" Eddy Flow -50.1 4.3100 35 27.00 CM2 191.3 37 27.00 4" Eddy Flow -48.9 4.3100 36 27.00 CM2 142.4 38 27.00 4" Eddy Flow -48.3 4.3100 37 27.00 CM2 94.1 39 27.00 4" Eddy Flow -47.9 4.3100 38 27.00 CM2 46.2 19 27.00 2½" Eddy Flow 2.7050 2T, 2E/2T 39 27.00 BL 46.2 © Copyright 2016 Sigma Development Group, Inc. Length Fitting Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total ft C Value ft Friction Loss ft psi/ft 4.0 C = 120 37.4 41.4 0.11236 10.0 0.0 C = 120 10.0 0.00338 10.0 0.0 C = 120 10.0 0.01218 10.0 0.0 C = 120 10.0 0.02587 4.0 0.0 C = 120 4.0 0.04427 PRANAUPGRADEPROOFCALC (Design Layer 1) Total (Pt) psi Elev (Pe) psi Notes Frict (Pf) psi Pt 108) 15.274 Pe 0.000 Pf 4.656 Pt 10) 19.930 Pe 0.000 Pf 0.034 Pt 11) 19.964 Pe 0.000 Pf 0.122 Pt 12) 20.086 Pe 0.000 Pf 0.259 Pt 13) 20.344 Pe 0.000 Pf 0.177 Total Pressure at Node 6) 20.521 psi 10.0 C = 120 Pt 34) 17.986 0.0 Pe 0.000 10.0 0.01339 Pf 0.134 10.0 C = 120 Pt 35) 18.120 0.0 Pe 0.000 10.0 0.00871 Pf 0.087 10.0 C = 120 Pt 36) 18.207 0.0 Pe 0.000 10.0 0.00504 Pf 0.050 10.0 C = 120 Pt 37) 18.258 0.0 Pe 0.000 10.0 0.00234 Pf 0.023 10.0 C = 120 Pt 38) 18.281 0.0 Pe 0.000 10.0 0.00063 Pf 0.006 264.0 C = 120 Pt 39) 18.288 93.6 Pe 0.000 357.6 0.00607 Pf 2.171 Page 9 of 11 IJ880Cf Dashboard Hydrau/lcs Pipe Information From Elev1 Pipe ID Flows ft Added Inside GPM Diameter Fittings To Elev2 Type in ft Total 18 27.00 611 Sch 10 6.3570 0 19 27.00 CM1 46.2 18 27.00 2½" Eddy Flow 2.7050 2T/2T 38 27.00 BL 47.9 17 27.00 6" Sch 10 46.2 6.3570 0 18 27.00 CM1 94.1 17 27.00 2½" Eddy Flow 2.7050 2T/2T 37 27.00 BL 48.3 16 27.00 6" Sch 10 94.1 6.3570 0 17 27.00 CM1 142.4 16 27.00 2½" Eddy Flow 2.7050 2T/2T 36 27.00 BL 48.9 15 27.00 611 Sch 10 142.4 6.3570 0 16 27.00 CM1 191.3 15 27.00 2½" Eddy Flow 2.7050 2T/2T 35 27.00 BL 50.1 14 27.00 6" Sch 10 191 .3 6.3570 0 15 27.00 CM1 241.4 14 27.00 2½" Eddy Flow 2.7050 2T/2T 34 27.00 BL 51.8 © Copyright 2016 Sigma Development Group, Inc. Length Fitting Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total Len Ftg Total PRANA UPGRADE PROOF CALC (Design Layer 1) ft C Value Total (Pt) psi ft Elev (Pe) psi Notes Friction Loss ft psi/ft Frict (Pf) psi 10.0 C = 120 Pt 19) 20.459 0.0 Pe 0.000 10.0 0.00009 Pf 0.001 Total Pressure at Node 18) 20.460 psi 260.0 C = 120 Pt 38) 18.281 74.9 Pe 0.000 334.9 0.00650 Pf 2.178 10.0 C = 120 Pt 18) 20.460 0.0 Pe 0.000 10.0 0.00035 Pf 0.004 Total Pressure at Node 17) 20.463 psi 260.0 C = 120 Pt 37) 18.258 74.9 Pe 0.000 334.9 0.00659 Pf 2.205 10.0 C = 120 Pt 17) 20.463 0.0 Pe 0.000 10.0 0.00076 Pf 0.008 Total Pressure at Node 16) 20.471 psi 260.0 C = 120 Pt 36) 18.207 74.9 Pe 0.000 334.9 0.00676 Pf 2.263 10.0 C = 120 Pt 16) 20.471 0.0 Pe 0.000 10.0 0.00131 Pf 0.013 Total Pressure at Node 15) 20.484 psi 260.0 C = 120 Pt 35) 18.120 74.9 Pe 0.000 334.9 0.00706 Pf 2.363 10.0 C = 120 Pt 15) 20.484 0.0 Pe 0.000 10.0 0.00202 Pf 0.020 Total Pressure at Node 14) 20.504 psi 260.0 C = 120 Pt 34) 17.986 74.9 Pe 0.000 334.9 0.00752 Pf 2.518 Page 10 of 11 118800 .. Dashboard Hydraulics Pipe Information From Elev1 Pipe ID Flows ft Added Inside GPM Diameter Fittings To Elev2 Type in ft Total 6 27.00 6" Sch 10 241.4 6.3570 14 27.00 CM1 293.3 1 27.00 6" Sch 10 1,281.6 6.3570 T 6 27.00 FM 1,574.9 0 0.00 6" Sch 10 6.3570 E 1 27.00 FR 1,574.9 © Copyright 2016 Sigma Development Group, Inc. Length Fitting Total Len Ftg Total Len Ftg Total Len Ftg Total ft C Value ft Friction Loss ft psi/ft 6.0 C = 120 0.0 6.0 0.00289 24.0 C = 120 37.7 61.7 0.06482 27.0 17.6 C = 120 44.6 0.06482 PRANAUPGRADEPROOFCALC (Design Layer 1) Total (Pt) psi Elev (Pe) psi Notes Frict (Pf) psi Pt 14) 20.504 Pe 0.000 Pf 0.017 Pt 6) 20.522 Pe 0.000 Pf 4.001 Pt 1) 24.522 Pe 11.699 Pf 2.891 Total Pressure at Node 0) 39.112 psi Page 11 of 11 MATERIAL DATA SUBMITTAL PRANA COLUMN SPRINKLER tt RECALC CARLSBAD, CA EPIC FIRE PROTECTION, INC. 765 TURTLE POINT WAY SAN MARCOS, CA 92069 (760)310-6122 FP-X(760)798-0556 1:qca Worldwide I Contacts www.tyco-fire.com Series TY-B -5.6 K-factor Horizontal and Vertical Sidewall Sprinklers Standard Response, Standard Coverage General Description The TYCO Series TY-B, 5.6 K-factor, Horizontal and Vertical Sidewall Sprin- klers described in this technical data sheet are standard response, standard coverage decorative 5 mm glass bulb type spray sprinklers designed for use in light and ordinary hazard, commer- cial occupancies such as banks, hotels, and shopping malls. They are designed for installation along a wall or the side of a beam and just beneath a smooth ceiling. Sidewall sprinklers are commonly used instead of pendent or upright sprinklers due to aesthetics or building construction considerations, where piping across the ceiling is not desirable. The recessed version of the Series TY-B Horizontal Sidewall Sprinkler is intended for use in areas with a fin- ished wall. It uses a two-piece Style 10 Recessed Escutcheon. The Recessed Escutcheon provides 1/2 in. (12,7 mm) of recessed adjustment or up to 3/4 in. (19,1 mm) of total adjustment from the flush sidewall position. The adjustment provided by the Recessed Escutcheon reduces the accuracy to which the fixed pipe nipples to the sprinklers must be cut. Corrosion-resistant coatings, where applicable, are utilized to extend the life of copper alloy sprinklers beyond that which would otherwise be obtained IMPORTANT Refer to Technical Data Sheet TFP2300 for warnings pertaining to regulatory and health information. Always refer to Technical Data Sheet TFP700 for the "INSTALLER WARNING" that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and installation can permanently damage a sprinkler system or its compo- nents and cause the sprinkler to fail to operate in a fire situation or cause ff to operate prematurely. Page 1 of 6 when exposed to corrosive atmo- spheres. Although corrosion resistant coated sprinklers have passed the standard corrosion tests of the appli- cable approval agencies, the testing is not representative of all possible cor- rosive atmospheres. Consequently, it is recommended that the end user be consulted with respect to the suit- ability of these coatings for any given corrosive environment. The effects of ambient temperature, concentration of chemicals, and gas/chemical velocity, should be considered, as a minimum, along with the corrosive nature of the chemical to which the sprinklers will be exposed. -The Series TY-B Sprinklers described herein must be installed and main-tained in compliance with this docu- ment, as well as with the applicable standards of the National Fire Protec-tion Association, in addition to the stan- dards of any other authorities having jurisdiction. Failure to do so may impair the performance of these devices. The owner is responsible for main- taining their fire protection system and devices in proper operating con- dition. Contact the installing contrac- tor or product manufacturer with any questions. Sprinkler Identification Numbers TY3351 .••.•..• Horizontal Sidewall TY3451 .•••....•.. Vertical Sidewall Technical Data Approvals UL and C-UL Listed FM Approved LPCB Certified NYC Approved (See Table A for complete approval information, including corrosion-resis- tant status.) MAY2020 Maximum Working Pressure See Table B Discharge Coefficient K=5.6 gpm/psi112 (80,6 Lpm/bar1l2) Temperature Ratings See Table A Finishes Sprinkler: See Table C Recessed Escutcheon: Signal or Pure White, Grey Aluminum, Jet Black, Chrome Plated, or Natural Brass Physical Characteristics Frame ............•.•............. Bronze Button •......••...•......... Brass/Copper Sealing Assembly .. Beryllium Nickel w/TEFLON Bulb •......•....................... Glass Compression Screw ........•.......• Bronze HSW Deflector .•...............•... Bronze VSW Deflector ..................... Copper TFP161 TFP161 Page 2 of 6 1 -Frame 2 -Button 3 -Sealing Assembly 4 -Bulb DEF~~TO,A ~ 51 : :,-,,, 5 -Compresston Screw 6 -Deflector" 6,. 4 2 3 1 1 -Frame 2 -Button 3 -Sealing Assembly 4 -Bulb DEF~~TOi~S' 5 -Compression Screw 6 -Deflector* 6• 4 2 3 1 1/2'"* NPT 9/16' 1/2' NPT ~~(14,3mm) •• .__,___.., l-,!s\f~~) 7/16" ] O~E:~~~~:R MAKE-IN CENTERLINE OF SPRINKLER WATERWAY 1-1/2' (38,1 mm) ~6~1~1~ WATERWAY 1_112, (38,1 mm) ESCUTCHEON ESCUTCHEON PLATE SEATING 2-3/16' PLATE SEATING 2-3/16' SURFACE ~55,6 mm) STYLE 10 RECESSED ESCUTCHEON SURFACE ~55,6 mm) STYLE 10 RECESSED ESCUTCHEON " Temperature rating is indicated on Deflector "" Pipe thread connections per ISO 7-1 can be =~s~ on special 2_718, DIA. (73,0mm) t *Temperature rating is indicated on Deflector 2-7/8" DIA (73,0mm) i ALL FINISHES EXCEPT POLY-STAINLESS POLY-STAINLESS FINISH ONLY FIGURE1 SERIES TY-B TY3351 HORIZONTAL SIDEWALL SPRINKLER 5.6 K-FACTOR STANDARD RESPONSE Poly-Stainless Physical Characteristics Frame ....•......................• Bronze Button ................ L316 Stainless Steer Bulb .............•.............•..• Glass Compression Screw ...•. L316 Stainless Steer HSW Deflector ....••......•. Copper/Bronze Sealing Assembly . Gold Plated Beryllium Nickel wffEFLON •Type L316 stalnless steel (UNS 31603) per ASTM A479/479M or BS EN 1008 WN1.4404. Operation The glass bulb contains a fluid which expands when exposed to heat. When the rated temperature is reached, the fluid expands sufficiently to shatter the glass bulb, allowing the sprinkler to activate and water to flow. Design Criteria The TYCO Series TY-B, 5.6 K-fac- tor, Horizontal and Vertical Side- wall Sprinklers are intended for fire protection systems designed in accordance with the standard installation rules recognized by the applicable Listing or Approval agency (for example, UL Listing is based on the requirements of NFPA 13, and FM Approval is based on the requirements of the FM Loss Preven- tion Data Sheets). Only the Style 10 Recessed Escutcheon, as applicable, is to be used for recessed horizontal installations. Installation The TYCO Series TY-B, 5.6 K-factor, Horizontal and Vertical Sidewall Sprin- klers must be installed in accordance with this section. General Instructions Do not install any bulb type sprinkler if the bulb is cracked or there is a loss of liquid from the bulb. With the sprin- kler held horizontally, a small air bubble should be present. The diameter of the air bubble is approximately 1/16 in. (1,6 mm) for the 135°F (57°C) to 3/32 in. (2,4 mm) for the 360°F (182°C) temper- ature ratings. * Temperature rating is indicated on Deflector. ESCUTCHEON PLATE SEATING SURFACE •• Pipe thread connections per ISO 7-1 can be provided on special request. ,[\~ (55,6 mm) fl ..... ..--~,..... 1-1/2' (38,1 mm) 1 -Frame 4 -Bulb 7 -Ejection 2 -Button 5 -Compression Spring 3 -Sealing Screw Assembly 6 -Deflector• ARROW MUST ,) POINTAWAY ~ FROM AND BE PERPENDICULAR @ TO THE BACK WALL SURFACE SHOWN SHOWN CROSS PENDENT UPRIGHT SECTION FIGURE2 SERIES TY-B VERTICAL SIDEWALL (TY3451) SPRINKLER 5.6 K-FACTOR, STANDARD RESPONSE MOUNTING I SURFACE ~ CLOSURE SERIES TY-B MOUNTING PLATE 1-1/4' (31,8 mm) ~ 5/8±1/4" (15,9±6,4 mm) FACE OF SPRINKLER FITTING 2-7/8' DIA. (73,0mm) 3/4' (19,1 mm) 3/4' (19,1 mm) 1/4' (6,4 mm) FIGURE3 SERIES TY-B RECESSED PENDENT SPRINKLER ASSEMBLY WITH TWO-PIECE 3/4 IN. TOTAL ADJUSTMENT STYLE 10 RECESSED ESCUTCHEON, 5.6 K-FACTOR, 1/2 IN. NPT A leak-tight 1/2 in. NPT sprinkler joint should be obtained by apply- ing a minimum-to-maximum torque of 7 to 14 lb-ft (9,5 to 19,0 N·m). Higher levels of torque may distort the sprin- kler inlet and cause leakage or impair- ment of the sprinkler. Do not attempt to make-up for insufficient adjustment in the escutcheon plate by under-or over- tightening the sprinkler. Readjust the position of the sprinkler fitting to suit. TFP161 Page 3 of6 WRENCH RECESS (END 'A' USED FOR 1/2' NPT MODELS) FIGURE4 W-TYPE6 SPRINKLER WRENCH WRENCH RECESS ~ ~ PUSH WRENCH INTO ENSURE ENGAGEMENT WITH SPRINKLER WRENCHING AREA FIGURES W-TYPE 7 RECESSED SPRINKLER WRENCH Horizontal Sidewall Sprinkler Installation The TYCO Series TY-B Recessed Hor- izontal Sidewall Sprinklers must be installed in accordance with the fol- lowing instructions. Install recessed horizontal sidewall sprinklers in the horizontal position with the centerline of waterway perpendicular to the back wall and parallel to the ceiling. The word "TOP" on the Deflector is to face towards the ceiling. Step A. After installing the Style 10 Mounting Plate over the sprinkler threads, hand-tighten the sprinkler into the sprinkler fitting. Step B. Tighten the sprinkler into the sprinkler fitting using only the W-Type 7 Recessed Sprinkler Wrench, see Figure 5. Apply the W-Type 7 Recessed Sprin- kler Wrench to the sprinkler wrench flats, see Figure 1. Step C. After the ceiling is installed or the finish coat is applied, slide on the Style 10 Closure over the Series TY-B Sprinkler and push the Closure over the Mounting Plate until its flange comes in contact with the ceiling. TFP161 Page 4 of 6 Vertical Sidewall Sprinkler Installation The Series TY-B Vertical Sidewall Sprinklers must be installed in accor- dance with the following instructions. Install vertical sidewall sprinklers in the pendent or upright position with the arrow on the Deflector pointing away from the wall. Step 1. With pipe thread sealant applied to the pipe threads, hand- tighten the sprinkler into the sprinkler fitting. Step 2. Tighten the sprinkler into the sprinkler fitting using only the W-Type 6 Sprinkler Wrench, see Figure 4. For wax-coated sprinklers, use an 8 or 10 in. adjustable Crescent wrench. Apply the W-Type 6 Sprinkler Wrench or the Crescent wrench, as applicable, to the wrench flats, see Figure 2. When installing wax-coated sprinklers with the adjustable Crescent wrench, exercise care to prevent damage to the wax coating on the sprinkler wrench flats or frame arms and, consequently, exposure of bare metal to the corro- sive environment. Open the jaws of the wrench sufficiently wide to pass over the wrench flats without damaging the wax coating. Before wrench-tighten- ing the sprinkler, adjust the jaws of the wrench to contact only the sprinkler wrench flats. After wrench tightening the sprinkler, loosen the wrench jaws before removing the wrench. After installation, inspect the sprin- kler wrench flats and frame arms and retouch (repair) the wax coating when- ever the coating has been damaged and bare metal is exposed. Retouch the wax coating on the wrench flats by gently applying a heated 1/8 in. diam- eter steel rod to the damaged areas of wax to smooth it back over areas where bare metal is exposed. -Only retouching of the wax coating applied to the wrench flats and frame arms is permitted, and the retouching is to be performed only at the time of the initial sprinkler installation. The steel rod should be heated only to the point at which it can begin to melt the wax, and appropriate precau- tions need to be taken when handling the heated rod in order to prevent the installer from being burned. Care and Maintenance The TYCO Series TY-B, 5.6 K-factor, Horizontal and Vertical Sidewall Sprin- klers must be maintained and serviced in accordance with this section. Before closing a fire protection system main control valve for maintenance work on the fire protection system that it controls, obtain permission to shut down the affected fire protection system from the proper authorities and notify all personnel who may be affected by this action. The owner must assure that the sprin- klers are not used for hanging any objects and that the sprinklers are only cleaned by means of gently dusting with a feather duster; otherwise, non- operation in the event of a fire or inad- vertent operation may result. Absence of an escutcheon, which is used to cover a clearance, may delay the time to sprinkler operation in a fire situation. Sprinklers which are found to be leaking or exhibiting visible signs of corrosion must be replaced. Automatic sprinklers must never be painted, plated, coated, or other- wise altered after leaving the factory. Modified sprinklers must be replaced. Sprinklers that have been exposed to corrosive products of combustion, but have not operated, should be replaced if they cannot be completely cleaned by wiping the sprinkler with a cloth or by brushing it with a soft bristle brush. Care must be exercised to avoid damage to the sprinklers before, during, and after installation. Sprin- klers damaged by dropping, strik- ing, wrench twist/slippage, or the like, must be replaced. Sprinklers that have a cracked bulb or that have lost liquid from its bulb must be replaced, see Installation Section. The owner is responsible for the inspection, testing, and maintenance of their fire protection system and devices in compliance with this document, as well as with the applicable standards of the National Fire Protection Associa- tion, such as, NFPA 25, in addition to the standards of any other authorities having jurisdiction. Contact the install- ing contractor or product manufacturer with any questions. Automatic sprinklers are recommended to be inspected, tested, and maintained by a qualified Inspection Service in accordance with local requirements and/or national codes. Sprinkler Finish 110) TFP161 Page 5 of6 Sprinkler Temperature Bulb K-factor Liquid Type Rating Color Natural I Chrome Polyester<= Poly-Lead Wax I Wax-Over-Lead Brass Plated Stainlessc Coated Coated Coated 135°F (57°C) Orange 155"F (68°C) Red Horizontal 175°F (79°C) Yellow 1, 2, 3, 4, 9 1, 2, 3, 9 1, 2, 3, 9 Sidewall (TY3351) 200°F (93°C) Green 1, 2 1, 2,3, 9 Figure 1 5.6 286°F (141°C) Blue 1b, 2b, 3b, 9b 112 in. NPT 360°F (182°C) Mauve 1, 2, 4, 9 1, 2, 9 NIA Recessed 135°F (57°C) Orange Horizontal 155°F (68°C) Red Sidewall 1, 2. 3, 9 1, 2 NIA (TY3351)• 175°F (79°C) Yellow Figure 3 2oo·F (93°C) Green 135°F (57°C) Orange Vertical 155°F (68°C) Red Sidewall 5, 6, 7, 9 5.6 (TY3451) 175°F (79°C) Yellow 5, 6, 7, 9 NIA 1/2 in. Pendent 5, 6, 7, 9 NPT or 200°F (93°C) Green Upright 286°F (141°C) Blue 5b, Sb, 7b, 9b Figure 2 360°F (182°C) Mauve 5, 6, 9 NIA NIA Notes: 1. UL Listed 1or use in Light and Ordinary Hazard Occupancies at a 4 to 12 in. (100 to 300 mm) top of deflector-to-<:eiling distance 2. C-UL Listed for use in Light and Or<lnary Hazard Occupancies at a 4 to 12 in. (100 to 300 mm) lop of deflector-to-celling distance 3. FM Approved for use In Light Hazard Occupancies at a 4 to 12 IN. (100 to 300 mm) top of deflector-to-ceiling distance 4. LPCB Approved (Ref. No. 094a & 007k) at a 4 to 6 In. (100 to 150 mm) denector-to-celling distance 5. UL Listed for uae in Light and Ordinary Hazard Occupancies 6. C-UL Listed for use in Light and Ordinary Hazard Occupancies 7. FM Appmved for use in Light Hazard Occupancies 8. LPCB Approved (Ref. No. 094a & 007k) 9. Approved by the City of New Vor1< under MEA 354-01-E 10. Where Polyester Coated. Lead Coated, Wax Coated, and Wax-over-Lead Coated Sprinklers are noted to be UL and C-UL Usted, the sprinklers are UL and C-UL Listed as corrosion-resistant sprinklera. Where Lead Coated, Wax Coated, and Wax-oYal'-lead Coated Sprinklers are noted to be FM Approved, the sprinklers are FM Approved as corrosion-resistant sprinklers. a. Installed with Style 10 (1/2 in. NPT) or Style 40 (3/4 in. NPT) 3/4 in. Total Adjustment Recessed Escutcheon. as applicable b. 1so•F (66'C) maximum ceijing temperature C. Frame and deflector only N/A -Not Applicable TABLE A SERIES TY-B 5.6 K-FACTOR HORIZONTAL AND VERTICAL SPRINKLERS LABORATORY LISTINGS AND APPROVALS Sprinkler Finish K-factor Sprinkler Type Natural I Chrome I Polyester1 I Lead I Wax I Wax-Over-Lead Brass Plated Coated Coated Coated Horizontal Sidewall (TY3351) 250 psi (17,2 bar)2 -OR 5.6 Recessed 175 psi (12,1 bar) Horizontal 1/2 in. Sidewall NPT (TY3351) Vertical Sidewall (TY3451) 175 psi (12,1 bar) Notea: 1. Frame and deflector only 2. The maximum working pressure ol 250 psi (17,2 bar) only applies to UL Listing, C-UL Listing and Approval by the City of New York TABLES SERIES TY-B 5.6 K-FACTOR HORIZONTAL AND VERTICAL SPRINKLERS MAXIMUM WORKING PRESSURE TFP161 Page 6 of 6 P/N 57 -XXX -X -XXX I I ~ SIN I 578 I HORIZONTAL SIDEWALL TY3351 1 I 575 I VERTICAL SIDEWALL TY3451 2 Notes: 3 SPRINKLER TEMPERATURE FINISH RATING NATURAL BRASS 135 135"F (57°C) POLY-STAINLESS GREY 155 155°F (68°C) ALUMINUM (RAL9007)1 POLYESTER 175°F (79°C) 175 PURE WHITE (RAL9010)2 POLYESTER 200 1. Available for TV3351 only 200°F (93°C) 2. Eastern Hemisphere sales only 4 SIGNAL WHITE (RAL9003) 3. Available only for 155 "f' (68 "C) or 200 •F (93 "C) temperature POLYESTER 286 286°F (141°C) rated sprinklers 4. AvaHable only for horizontal sidawaH TV3351 for use In Deluge 5 JET BLACK (RAL9005)3 Systems ("OPEN' indicates sprinkler assembly without glHs POLYESTER 360 360°F (182°C) bulb, button, and sealing assembly) 6 WAX COATED 286 °F (141 °C) MAX 000 OPEN4 7 LEAD COATED 8 WAX-OVER-LEAD 286 °F (141 "C) MAX 9 CHROME PLATED TABLEC SERIES TY-B HORIZONTAL AND VERTICAL SIDEWALL SPRINKLERS PART NUMBER SELECTION Color Sprinkler Part Number Temperature Rating Black 135°F (57°C) 56-065-1-135 Red 155°F (68°C) 56-065-1-155 Yellow 175°F (79°C 56-065-1-175 Blue 200°F (93°C) 56-065-1-286 286°F (141°C) TABLED SERIES TY-B HORIZONTAL AND VERTICAL SIDEWALL SPRINKLERS WAX RETOUCHING STICK PART NUMBER SELECTION Limited Warranty For warranty tenns and conditions, visit www.tyco-fire.com. Ordering Procedure Contact your local distributor for avail- ability. When placing an order, indicate the full product name and Part Number (PIN). Sprinkler Assemblies with NPT Thread Connections Specify: Series TY-8 (specify SIN), (specify K-factor), (specify Horizontal or Vertical Sidewall) Sprinklers with (specify) temperature rating, (specify) finish or coating, P/N (See Table C) Recessed Escutcheon Specify: Style 10 Recessed Escutch- eon with (specify) finish, P/N (specify•) • Refer to Technical Data Sheet TFP770 Sprinkler Wrench Specify: W-Type 6 Sprinkler Wrench, P/N 56-000-6-387 Specify: W-Type 7 Sprinkler Wrench, P/N 56-850-4-001 1400 Ponnbrook Parkway, Lanadale, PA 19446 f TelophoM +1-215-362-0700 Wax Sticks (for retouching wrench-damaged wax coating) Specify: (specify color, below) Colored Coded Wax Stick for retouching (specify temperature rating) tempera- ture-rated Series TY-8 Sprinklers, P/N (specify) Note: Each wax stick is suitable for retouching up to 25 sprinklers. Note: The wax used for 286°F (141°C) sprinklers is the same as for 200°F (93°C) sprinklers, and therefore the 286°F (141°C) sprinkler is limited to the same maximum ceiling temperature as the 200°F (93°C) sprinkler, that is 150°F (66°C). 0 2020Johnson Controla. All r1ghta .,. .. rved. AN 1peclftcaUou and ottt.r lnfomatlon &hown were CVffffltH of document revision data and,,.. aubjectto changa wtthoutnotlca. p,&A,TIONN..AREPROTECT10NASSOC6A.TION8'1d~ ... revietffed~o1Na'lona1RrllPfot,c:t:ioflAMQclation; Johnson f}g, Controls TEF\.DN1aa,.,-tetundeinar1totDI.IPofit Eddythread 40 A Lightweight Schedule 40 Replacement Pipe That Has a Corrosion Resistance Ratio of 1.0 Bull Moose Tube Company has been making pipe for a long time and is recognized as a producer of quality pipe products. Eddythread 40 is designed with the same thoroughness as our other fine pipe products and now our customers have an option to buy a carefully designed replacement for Schedule 40 that: Has a Corrosion Resistance Ratio of 1.0 Has a Pressure Rating of 300 psi Is Lighter Weight Than Schedule 40 Is Approved by Factory Mutual and Listed by Underwriters Laboratories Is Produced in Accordance to ASTM A-135 and A-795 Can be Used With Standard Schedule 40 Threaded Fittings, Couplings and Valves Is Produced From Steel With Excellent Properties of Strength and Threadability Can be Used in Wet, Dry, Preaction, and Deluge Type Sprinkler Systems* Offers Lower Freight Costs EDDYTHREAD 40 SPECIFICATIONS NOMINAL PIPE SIZE (in) M¥MiiMiMIIA ..;; M:JiiiMIMH 11/4 11/2 2 1.461 2.070 2.547 3.308 1.083 1.418 1.654 2.123 70 51 44 30 CORROSION RESISTANCE RATIOS 1 1/4 11/2 2 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 • Eddythread 40 can be hot dipped galvanized to meet FM's requirement for dry systems ACBPlJKOcompany 1819 Clarkson Road Chesterfield, MO 63017 (800)32~7 FAX: (636) 537-2645 www.bullmoosetubc.com e-mail :sales@bullmoosetube.com For additional information, contact your salesperson today at (800) 325-4467 or (636) 537-2600 in the USA, or from Canada call (800) 882-4666 c~usA~ <9> APPROVED Al Information contained herein is accurate as known at the time of publication. Bull Moose Tube reserves the right lo change product specifications without notice and wtthout incurring obligatllon. 8/08 13 (I~~• f I• I Threaded Mechanical Branch Tee The MT-30 mechanical tee serves the same function as the MT-1 and MT-8, but uses a steel electro-plated u-bolt to save space and For easier installation in tight places. The MT-30 is ideal for direct connections with sprinkler heads and drop nipples. The MT-90 is the BSPT equivalent. For the latest UL/ULC listed, LPCB, VdS and FM Approved pressure ratings versus pipe schedule, see www.anvilintl.com or contact your local Anvil Representative. ,@us <8> USTBI APPROVED ForU.~App.-OetabandLJ,rllatioM. vt&it0l6websllleatwww.arwlina.l»mor contact an ArrvP Salet RepresontaliYe. MATERIAL SPECIFICATIONS HOUSING: COATINGS: Ductile Iron conforming to ASTM A-536, Grade 65-45-12 0 Zinc Electroplated 0 Other available options: Example: RA13000 or RAL9000 Series U-BOLT & NUTS: U-bolt is carbon steel SAE J.429 Gr. 2, zinc plated c:omplete with hex Ranged lock GASKETS: Materials nuts conforming lo ASTM A-563 Gr. A or B of SAE 1995 Gr. 2. Properties as designated in accordance with ASTM 0-2000. THREADS: NPT per ANSI/ ASME B 1.20. 1. Project: Address: Contractor: Engineer: Submittal Date: Notes 1: Notes 2: FP-10.16 PROJECT INFORMATION 0 Grade "E' EPDM (Green color code) -40°F to 230°F (Service Temperature Range)(-40°C lo 110°C) Recommended for water service, diluted acids, alkalies solutions, oil-free air and many chemical services not involving hydrocarbons, oils or gases. NOT FOR USE WITH HYDROCARBONS. APPROVAL STAMP □Approved D Approved as noted D Not approved Remarks: FIG. MT-30 Threaded Mechanical Branch Tee ll'Jl!Ktl•■ •I ; •111::i••··· 1 .... -. .. ... _:t•#•11111o1: Nominal Hole Dimensions Max. Dimensions 0.0. Working Size Min.Diomeler Max. Diameter Pressure• A B ln./0ll(mm] In.Imm In.Imm In.Imm ,Sl/1,ar In.Imm In.Imm l¼x½ 1.660 X 0.840 11/1, 1½, 300 21/1 3½ 32· 2 424>213 Jf) 33 J.07 54 69 l¼x¼ 1.660 X 1.050 11/1, 1½, 300 2¼ 3½ :Jtilq 41,d~ 3G 3:J LO' 5~ 89 l¼xl l.660 x l.315 11/1, 11/1, 300 2¼ 3½ 3J,25 424xJJ.1 3( 33 JG1 Se 8~ l½x½ 1.900 X 0.840 11/1, l½, 300 21/, 3½ JC,12 48,1rl'.3 ~o .f.'.J lGJ (' Y. l½x¼ l.900x l.050 11/i, Ph, 300 21/, 3½ ,c,. q 483x 26.l 30 J,1 lfl 5? $9 l½xl l.900 xl.315 Ph, l½, 300 21/a 3½ 4,1.,2, JBJ,33.7 30 .,3 !Gl 6; 89 2x ½ 2.375 x0.840 l½, l¼, 300 2½ 33/1 5(it'l 6~3,21.J 30 33 JC,/ M •5 2x ¼ 2.375 x l.050 11/i, 1½, 300 2½ 31/1 'vx J 60 . .ix'l6.? 311 J3 107 64 9' 2xl 2.375xl.315 11/11 11/11 300 2½ 31/1 50,:;, 6:J.J .>. 3~? 1 3/J :3 2C/ £; 9:, 2½x½ 2.875 X 0.840 rn, 1½, 300 2¼ 41/1 61.,'7 130•'1:3 3n ,1J 1e::" 70 1GB 2½x¼ 2.875x l.050 13/1, 15/u 300 21/, 4¼ 65,:9 130116/ 30 .iJ 201 10 /08 2½xl 2.875xl.315 11/i, 1¼, 300 21/a 4¼ 65,75 lSDxJJ/ 30 JJ 707 13 108 BSP equM>lent is available as a MT-90. a -Working Pressure Ratings ore for reference only and bo.ed on Sch. 10 and Sch. 40 pipe. For !he latest UI/ULC, FM, VdS and IPCB pressure ratings,,.,,..,. pipe schedule, please visit anviintcom or contact your local Anv~ Representative. Nair. ,,ghten nuts alternately to a recommended torque of 18-22 &..lbs. (25-30 Nm) on pipe wall less than sche<iile 10 (Din 24401 or 23-27 &.-lbs. (31-37 Nm) on pipe walls schedule 10 (DIN 2.MO) and above, FP-10.16 Approx. ( T Wt.Ea. Toke-out In.Imm In.Imm Lbs./Ko 2¼ 1% 0.8 \/2 4J 04 21/, l½ 0.8 Sil 42 D4 2¼ 1¾ l.l ;I' .;1 ,.s 21/, l¼ 0.8 5ll ~.1 4 2¼ l¼ 0.9 )/"J 4d OA 2¼ l¼ l.l ill 43 9.5 2¼ 2 0.9 5?7 51 01 2V. 2 0.9 J,f l J ~ 2¼ 2 l.l 51' ,a QI 2¼ 21/1 0.9 ll'i 5,-04 21/, 2¼ 0.9 51; 51 04 2¼ 2¼ l.l )li 56 0) !A WARNING! foril.t:"tio~c;.t:: ... ~~ Gruvlok-Xtr■me™ Lubricant is requir■d. FIG. MT-30 & MT-90 Threaded Mechanical Branch Tees @&Mtt~ 1 Alignment Align the gasket and fitting above the 1.19' (30mm) pipe hole. Note: Flow Data is expressed as FeeVMeters of Schedule 40 steel outlet pipe with a "Hazen-Williams coefficient of friction value of 120". Step 3 3Tighten Nuts Making sure the fitting is properly located over the pipe hole, use a 9'1s' (14 mm) wrench to tighten the nuts alternatively to a recommended torque of 18-22 ft.-lbs. (25-30 Nm) on pipe wall less than schedule 10 (DIN 2440) or 23-27 ft.-lbs. (31-37 Nm) on pipe walls schedule 10 (DIN 2440) and above. FP-10.16 Step 2 2 Housing Assembly Attach the U-bolt from the other side and fasten the nuts finger tight. Specified Bolt Torque Specified bolt torque is for the u-bolt used on SPF9 threaded mechanical branches. The nuts must be tightened alternately and evenly until fully tightened. Caution: Proper torquing of mechanical branch u-bolt is required to obtain specified performance. Over torquing the u-bolt may result in damage to the pipe and/or casting which could result in pipe joint separation. Under torquing the u-bolt may result in lower pressure retention capabilities, lower bend load capabilities, joint leakage and pipe joint separation. Pipe joint separation may result in significant property damage and serious injury. RING HANGERS ANVIC Fig. 69 (Formerly Afcon Fig. 300) Adjustable Swivel Ring, Tapped Per NFPA Standards Size Range: 1/i" through 8" Material: Carbon steel Finish: Strap is Pre-Galvanized Zinc Material. Nut is Zinc Plated. Service: Recommended for suspension of non-insulated stationary pipe line. Maximum Temperature: 450" F Approvals: Complies with Federal Specification A-A-ll92A (Type 10), WW-H-171-E (Type 10), and ANSI/MSS SP-58 (Type 10). UL Listed and FM Approved (Sizes 3/◄" -8"). Features: • 1/2" -2" sizes designed for use with steel and CPVC piping and manufactured with FBC System Compatible oil. • Threads are countersunk so that they cannot become burred or damaged. • Knurled swivel nut provides vertical adjustment after piping is in place. • Captured swivel nut in the 1/i" through 6" sizes. The capture is permanent in the bottom portion of the band, allowing the hanger to be opened during installation if desired, but not allowing the nut to fall completely out Ordering: Specify size, figure number and name. Non-captured nut also available upon request. -JAr- 1/," through l" pipe 11/ •" through 2" pipe 21/i" through 8" pipe FIG. 69: DIMENSIONS (IN) • LOADS (LBS) • WEIGHT (LBS) Pipe Size Max Load Weight Rod Size B C F G A Width ½ 0.10 27/4 2 1% --¾--~ 2¾ 17/4 11/is --1--~ 29/ts 111/ts 1 5/e --1-1/.-,-300 ~ 2¾ 1¾ __ 1_½ __ ~ 3/g 2¾ 1¾ 11a ~ ~ 3¼ 2¾ 1¼ 2½ 525 0.20 4 2¾ 11/is ~ '"o:2o 3131ts 215/ts 13/is 4 650 0.30 411/ts 313/,s 1% ¼ 5 0.54 5% 4¾ :=c 1,000 ~ ½ 611/ts 59/\s 2¼ 8 ~ 8% 7% 3¼ PROJECT INFORMATION Project: □Approved 1/," through 2" Size Rounded Edge Design c@m <8> USTEI APPROVED 21/i" through 8" Size APPROVAL STAMP Address: □Approved as noted Contractor: D Not approved Engineer: Remarks: Submittal Date: Notes 1: Notes 2: PH-1.18 8007957 GST10 X CPVC 1-112 300 1 5 -8020957 SWG10 X CPVC 1-112 300 1.5 8008957 GST 20 X 2-1/2 850 1.5 X 1475 1.5 8068925 GST 20S$ X 2-112 850 1.5 8010957 GST 30 X 4 1500 1.5 X 4 1475 1.5 8009925 GST 25-380 X 4 1500 1.5 X 4 1475 1.5 8022925 SWG 25-380 X 3-1/2 -4• 1500 1.5 X 1475 1.5 8021957 SWG20 X 2-112 -3" 1250 1.5 8073925 SWG20 SS X 2-1/2 1250 1.5 8139957 SH GST 20 X 3 1050 1.5 X 4 1475 1.5 8141957 SH GST 30 X 4 1500 1.5 X 4 1475 1.5 8140957 SH GST 20SS X 3 1050 1.5 8142957 SH GST 30 SS X 1500 1.5 8038957 DSTR 1 1500 0.035 0.1050 8037957 DSTR 1-1i2 X 1500 0 035 X 0.1050 8039957 DSTR 516 X 4 1500 0 037 X 4 0.1050 8045957 DST 516 X 4 1500 0 188 X 4 0.1875 8046957 TEK 50 X 1500 0.250 X 4 0.1875 8055957 SWDR1 X 4 1500 0.037 X 0.0600 8056957 SWOR 516 X 4 1500 0.037 X 4 1475 0.0600 8054957 SWOR 1-1/2 X 4 1500 0.037 X 4 1475 0.0600 8137957 SH DSTR 1 X 4 1500 0-035 X 1475 01050 8150922 XP20 X 2 750 0.027 X 4 1475 0.1050 8153922 XP 35 X 3-1/2 1250 0 043 X 4 1475 0.1050 BX P/N CONCRETE FM FM Max FMTHt Material PipeSl:te Load 8059957 CST 20 X 4 1475 3000PSI 8061957 SWC20 X 1475 3000 PSI • SWG 25-380 Maximum pipe size in composite wood joist allowed by UL is 3-1 /2" SWG 25-380 Maximum pipe size in wood timber or joist allowed by UL is 4" •• SWG 20 Maximum pipe size in composite wood joist allowed by UL is 2-1/2" Buildex .. SWG 20 Maximum pipe size in wood timber or joist allowed by UL is 3" UL and FM tests were performed in compliance with NFPA-13 Standards. www.itwbuildex.com Fastening requirement: 5 times weight of water filled schedule 40 pipe plus 250 pounds. 800-284-5339 S5S26 tqca Series EL0-2318-11.2 K-factor Worldwide I www.tyco-fire.com Contacts Upright and Pendent Sprinklers Standard Response, Standard Coverage IMPORTANT Refer to Technical Data Sheet TFP2300 for warnings pertaining to regulatory and health information. Always refer to Technical Data Sheet TFP700 for the "INSTALLER WARNING" that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and installation can permanently damage a sprinkler system or its compo- nents and cause the sprinkler to fail to operate in a fire situation or cause it to operate prematurely. Scan the QR code or enter the URL in a web browser to access the most up-to-date electronic version of this document. Data rates may apply. docs.jci.com/tycofire/ series-elo231 b_ 11-2K General Description TYCO Series EL0-2318 11.2K Standard Response, Standard Coverage Upright and Pendent Sprinklers (Ref. Figure 1) are automatic sprinklers of the frangible bulb type. They are standard respons~, spray sprinklers that produce a hemi- spherical water distribution pattern below the deflector. The 11.2 K-factor, EL0-2318 Sprinklers were subjected to full-scale, high-piled storage fire tests to qualify their use in lieu of 5.6 or 8.0 K-factor standard spray sprinklers for the protection of high-piled storage. Page 1 of 6 Higher flow rates can be achieved at much lower pressures with the 11.2 K-factor, EL0-2318 Sprinklers, making their use highly advantageous in high density applications, such as the pro- tection of high-piled storage. Wax or lead coatings can be used to extend the life of the copper alloy components used in Series EL0-2318 Sprinklers beyond that which would otherwise be obtained when exposed to corrosive atmospheres. Although wax, lead, and polyester coated sprin- klers have passed the standard corro- sion tests of the applicable approval agencies, the testing is not repre- sentative of all possible corrosive atmospheres. Consequently, it is rec- ommended that the end-user be con- sulted with respect to the suitability of these corrosion resistant coatings for any given corrosive environment. The effects of ambient temperature, concentration of chemicals, and gas/ chemical velocity, should be consid- ered, as a minimum, along with the cor- rosive nature of the chemical to which the sprinklers will be exposed. An upright intermediate level version of the Series EL0-2318 Sprinklers for in-rack applications can be obtained by utilizing the Series EL0-2318 Upright Sprinkler with the WSG-2 Guard & Shield, and a pendent intermediate level version of the Series EL0-2318 Sprinklers can be obtained by uti_lizing the Series EL0-2318 Pendent Sprinkler with the WS-2 Shield. If there is a pos- sibility of the pendent intermediate l~vel version being exposed to mechanical damage, a G-2 Guard can be added. -The 11.2 K-factor, Series ELO-2318 Upright and Pendent Sprinklers described herein must be installed and maintained in compliance with this document, as well as with the applica- ble standards of the National Fire Pro- tection Association (NFPA), in addition to the standards of any other authori- ties having jurisdiction. Failure to do so may impair the performance of these devices. The owner is responsible for main- taining their fire protection system NOVEMBER 2021 t~1 ~ and devices in proper operating con- dition. Contact the installing contrac- tor or product manufacturer with any questions. Installation of Series ELO-2318 Pendent Sprinklers in recessed escutcheons will void all sprinkler warranties, as well as possibly void the sprinkler's Approvals and/or Listings. Sprinkler Identification Numbers (SINsJ Refer to Table A for sprinkler identifica- tion numbers. TFP342 TFP342 Page 2 of6 2-13/16" (71,4mm) lYP. /2" PT 112• (12,7 mm) ~MINAL MAKE-IN THREAD RELIEF 3/4" NPT 3/4" NPT Components: 1 -Frame 2 -Seal Assembly 3 -Cap 4 -Bulb 5 -Compression Screw 6 -Deflector* 7/16"(11 ,1 mm) NOMINAL MAKE-IN ~/2" (12,7 mm) NOMINAL MAKE-IN * Temperature rating is indicated on deflector. UPRIGHT UPRIGHT PENDENT CROSS TY5851 TY5151 TY5251 SECTION FIGURE1 SERIES EL0-231B 11.2K UPRIGHT 3/4 INCH NPT (TY5151), UPRIGHT 1/2 INCH NPT (TY5851), AND PENDENT 3/4 INCH NPT (TY5251) SPRINKLERS, STANDARD RESPONSE Technical Data Approvals UL and C-UL Listed FM Approved NYC Approved VdS Approved Refer to Table C for specific details on laboratory and approvals, including corrosion-resistant status. The approv- als apply to the service conditions indi- cated in the Design Criteria section.) Finishes Refer to Table C Physical Characteristics Frame ............................ Bronze Cap .............................. Bronze Sealing Assembly .. Beryllium Nickel w/TEFLON Bulb (5 mm dia) ..................... Glass Compression Screw ..........•...•.. Bronze Deflector .......................... Bronze Additional Technical Data Refer to Table A for additional techni- cal data. Operation The glass bulb contains a fluid that expands when exposed to heat. When the rated temperature is reached, the fluid expands sufficiently to shatter the glass bulb, allowing the sprinkler to activate and water to flow. Item Description TY5151 -Upright 3/4 in. NPT TY5251 -Pendent 3/4 in. NPT 1Y5851 -Upright 1/2 in. NPT Sprinkler Identification Number (SIN) TY5151 is a re-designation for Central SIN C5151. TY5251 is a re-designation for Central, Gem, and StarSINs C5251, G1871, and 52531, respectively. TY5851 is a re-designation for Central SIN C5851. K-factor, (gpm/psQ (lpm/bar) 11.2 GPM/psi¼ (161,4 LPM/bar¼) 155 °F (68 °C)1 Temperature Rating °F (°C)1 200 °F (93 °C) 286 °F (141 °C) Thread Size 3/4 in. NPT or 1/2 in. NPT Sprinkler Orientation Upright/Pendent Maximum Working Pressure, psi (bar) 175 psi (12,1 bar) Note: 1. Refer to Table C for laboratory listings and approvals. TABLE A SERIES EL0-231B 11.2K UPRIGHT AND PENDENT SPRINKLERS TECHNICAL DATA Design Criteria UlandC-UL Listing Requirements TYCO Series EL0-2318 11.2K Standard Response, Standard Coverage Upright and Pendent Sprinklers are to be installed in accordance with NFPA 13 standard sprinkler position and area/ density flow calculation requirements for light, ordinary, or e~tra h~d occu- pancies, as well a~ h1~h-ptled st~rage occupancies (sohd-p1led, palletized, rack storage, bin box, and sheH storage including but not limited to Class I-IV and Group A plastics) with a minimum residual (flowing) pressure of 7 psi (0,5 bar) for wet or dry pipe systems. Refer to Table B for additional information. FM Approval Requirements The 11.2 K-factor, Model EL0-2318 Sprinklers are to be installed in accor- dance with the applicable control mode density/area guidelines provided by FM Global. Note: FM Approval guidelines may differ from UL and C-UL Listing criteria. Storage Type Sprinkler Type Response Type System Type Temperature Rating °F (0C)1 Open Frame (that is, no solid shelves) Single, Double, Multiple- Row, or Portable Rack Storage of Class HV and Group A or B Plastics Solid PUe or Palletized Storage of Class HV and Group A or B Plastics Idle Pallet Storage Rubber Tire Storage Rolled Paper Storage (Refer to the standard.) Flammable liquid Storage (Refer to the standard.) Aerosol Storage (Refer to the standard.) Automotive Components in Portable Racks (Control mode only, refer to the standard.) Note: 1. Rater to Table C for laboratory listings and approvals. NIA -Not Applicable TABLES NFPA Standard Coverage SR Wet, Dry 155 °F {68 °c)1 200 °F (93 °C) 286 °F (141 °C) Refer to NFPA 13 Refer to NFPA 13 Refer to NFPA 13 Refer to NFPA 13 Refer to NFPA 13 Refer to NFPA 30 Refer to NFPA 30B Refer to NFPA 13 TFP342 Page 3 of 6 FM Global Storage SR Wet, Dry 155 °F (68 °q1 200 °F (93 °C) 286 °F (141 °C) Refer to FM 2-0 and 8-9 Refer to FM 2-0 and 8-9 Refer to FM 2-0, 8-9, and 8-24 Refer to FM 2-0 and 8-3 Refer to FM 8-21 Refer to FM 7-29 Refer to FM 7-31 N/A SERIES ELO-231B 11.2K UPRIGHT AND PENDENT SPRINKLERS COMMODITY SELECTION AND DESIGN CRITERIA OVERVIEW SPRINKLER FINISH SPRINKLER TEMPERATURE BULB TYPE RATING LIQUID NATURAL I CHROME LEAD I WAX I WAX-OVER-LEAD BRASS PLATED COATED COATED COATED 155°F (68°C) Red UPRIGHT 3 (TY5151 & TY5851t 200°F (93"Cl Green 1, 2, 3, 4, 5 286°F (141"C) Blue 3 I 3• 155°F (68°C) Red PENDENT 3 (TY5251) 200°F (93°C) Green 1, 2, 3, 4, 5 286°F (141°C) Blue 3 I 3a Notea: 1. Listed by Underwr!teB Laboratories, Inc. (U~ 2. Listed by Underwrite,. Laboratories, Inc. for use in Canada (C-UL) 3. Approved by FM Global (FM Approvals) 4. Approved by the City of New Yori< (NYC) under MEA 291-04-E 5. VdS Approved a. Ustad/Approved for a maximum celling temperature of tSO"F (66"C). TABLEC SERIES ELO-231B 11.2K UPRIGHT AND PENDENT SPRINKLERS, STANDARD RESPONSE LABORATORY LISTINGS AND APPROVALS TFP342 Page 4 of 6 •FITTING SIDE• TOWARDS SPRINKLER FITTING A)✓~\ WRENCH RECESS a:ND •A') FIGURE2 W-TYPE3 SPRINKLER WRENCH Installation TYCO Series ELO-231B 11.2K Stan- dard Response, Standard Coverage Upright and Pendent Sprinklers must be installed in accordance with this section. A leak-tight 3/4 in. NPT sprinkler joint should be obtained by applying a min-imum-to-maximum torque of 10 to 20 lb-ft (13,4 to 26,8 N·m). A leak-tight 1/2 in. NPT sprinkler joint should be obtained by applying a minimum-to-maximum torque of 7 to 14 lb-ft (9,5 to 19,0 N•m). Higher levels of torque can distort the sprinkler inlet with con-sequent leakage or impairment of the sprinkler. Notes: Do not install any bulb type sprinkler if the bulb is cracked or there is a loss of liquid from the bulb. With the sprinkler held horizontally, a small air bubble should be present. The diameter of the air bubble is approxi- mately 1116 in. (1,6 mm) for the 155°F (68°C) to 3/32 in. (2,4 mm) for the 286°F (141°C) temperature ratings. Do not attempt to make up for insuf- ficient adjustment in the escutcheon plate by under-or over-tightening the sprinkler. Re-adjust the position of the sprinkler fitting to suit. The Series ELO-2318 Upright and Pendent Sprinklers must be installed in accordance with the following instructions. Note: Pendent sprinklers are to be installed in the pendent position; upright sprinklers are to be installed in the upright position. Step 1. With pipe thread sealant applied to the pipe threads, hand- tighten the sprinkler into the sprinkler fitting. Step 2. Tighten the sprinkler into the sprinkler fitting using only the W-Type 3 Sprinkler Wrench (Ref. Figure 2), except that an 8 in. or 10 in. adjustable wrench is to be used for wax-coated sprinklers. With reference to Figure 1, the W-Type 3 Sprinkler Wrench or the adjustable wrench, as applicable, is to be applied to the wrench flats. When installing wax-coated sprinklers with the adjustable wrench, additional care needs to be exercised to prevent damage to the wax coating on the sprinkler wrench flats or frame arms and, consequently, exposure of bare metal to the corrosive environment. The jaws of the wrench should be opened sufficiently wide to pass over the wrench flats without damaging the wax coating. Before wrench-tightening the sprinkler, the jaws of the wrench are to be adjusted to just contact the sprin- kler wrench flats. After wrench-tight-ening the sprinkler, loosen the wrench jaws before removing the wrench. After installation, the sprinkler wrench flats and frame arms must be inspected and the wax coating retouched (repaired) whenever the coating has been damaged and bare metal is exposed. The wax coating on the wrench flats can be retouched by gently applying a heated 1/8 in. diam- eter steel rod to the areas of wax that have been damaged, to smooth it back over areas where bare metal is exposed. Notes: Only retouching of the wax coating applied to the wrench flats and frame arms is permitted, and the retouching is to be performed only at the time of the initial sprinkler installation. The steel rod should be heated only to the point at which it can begin to melt the wax, and appropriate precau- tions need to be taken, when handling the heated rod, in order to prevent the installer from being burned. If attempts to retouch the wax coating with complete coverage are unsuc- cessful, additional wax can be ordered in the form of a wax stick (the end of which is color-coded). Only the correct color-coded wax is to be used, and retouching of wrench !fats and frame arms is only permitted at the time of initial sprinkler installation. With the steel rod heated as previ- ously described, touch the rod to the area requiring additional wax with the rod angled downward, and then touch the wax stick to the rod approximately 1/2 in. away from the area requiring retouching. The wax will melt and run down onto the sprinkler. Care and Maintenance TYCO Series ELO-2318 11.2K Standard Response, Standard Coverage Upright and Pendent Sprinklers must be main- tained and serviced in accordance with this section. Before closing a fire protection system control valve for maintenance work on the fire protection system that it con- trols, permission to shut down the affected fire protection system must be obtained from the proper authorities and all personnel who may be affected by this action must be notified. Sprinklers that are found to be leaking or exhibiting visible signs of corrosion must be replaced. Automatic sprinklers must never be painted, plated, coated or other- wise altered after leaving the factory. Modified sprinklers must be replaced. Sprinklers that have been exposed to corrosive products of combustion, but have not operated, should be replaced if they cannot be completely cleaned by wiping the sprinkler with a cloth or by brushing it with a soft bristle brush. Care must be exercised to avoid damage to the sprinklers before, during, and after installation. Sprin- klers damaged by dropping, striking, wrench twist/slippage, or the like, must be replaced. Also, replace any sprin- kler that has a cracked bulb or that has lost liquid from its bulb. For additional information, refer to Installation section. Frequent visual inspections are rec- ommended to be initially performed for corrosion resistant sprinklers, after the installation has been completed, to verify the long term potential integrity of the sprinkler coatings. Thereafter, annual inspections per NFPA 25 should suffice; however, instead of inspecting from the floor level, a random sampling of close-up visual inspections should be made, so as to better determine the exact sprinkler condition and the long term integrity of the corrosion resistant coating, as it may be affected by the corrosive conditions present. The owner is responsible for the inspection, testing, and maintenance of their fire protection system and devices in compliance with this document, as well as with the applicable standards of the National Fire Protection Associ- ation, such as NFPA 25, in addition to the standards of any other authorities having jurisdiction. Contact the install- ing contractor or product manufacturer with any questions. P/N 50-XXX-X-XXX I I I SIN I 501 11.2K UPRIGHT (1/2 in. NPT) TY5851 1 510 11.2K UPRIGHT (3/4 in. NPT) TY5151 6 512 11.2K PENDENT (3/4 in. NPT) TY5251 7 8 9 TABLED SPRINKLER FINISH NATURAL BRASS WAX COATED LEAD COATED WAX-OVER-LEAD COATED CHROME PLATED 155 200 286 TFP342 Page 5 of 6 TEMPERATURE RATING 155•F (68°C) 200°F (93°C) 286°F (141°C) SERIES EL0-231B 11.2K UPRIGHT AND PENDENT SPRINKLERS, STANDARD RESPONSE It is recommended that automatic sprinkler systems be inspected, tested, and maintained by a qualified Inspec- tion Service in accordance with local requirements and/or national codes. Limited Warranty For warranty terms and conditions, visit www.tyco-fire.com. PART NUMBER SELECTION Ordering Procedure Sprinkler Assemblies with NPT Thread Connection Specify: Series EL0-231B 11.2K Stan- dard Response (specify Pendent or Upright) Sprinkler, SIN (specify), (specify temperature rating), with (specify) finish, P/N (specify from Table D) Sprinkler Wrench Specify: W-Type 3 Sprinkler Wrench, P/N 56-895-1-001 Wax Sticks (for retouching wrench-damaged wax coating) Specify: (specify Color) color-coded Wax Stick for retouching (specify tem- perature rating) temperature rated Series EL0-231B Sprinklers, P/N (specify): Red for 155'F (68"C) ........•.. 56-065-1-155 Blue for 200'F (93'C) and 286°F (141"C) ...•......... 56-065-1-286 Notes: Each wax stick is suitable for retouching up to twenty-five sprinklers. The wax used for 286°F (141°C) sprin- klers is the same as for 200°F (93°C) sprinklers, and, therefore, the 286°F (141°G) sprinkler is limited to the same maximum ceiling temperature as the 200°F (93°C)sprinkler, such as 1so°F (66°C). TFP342 Page 6 of6 1400 Pennbrook Parkway, Lansdale, PA 19446 I Telephone +1-216-36Z.0700 GUltJellrwonC.nlroll.Alr19hllrw••r¥ed.A11.-clflc.atloMandotherMtormatktftS,..... ... CUl'NftlMof~rnlaloft•ta~--~-chMeewfthoutftOtice. NAl\ONALRREf'ROTI:CllONAUOClATlONWld~-r-vit.._,.,~ofW.-Or\llf'wwPl'oa..:UDn~ Tm..DNllla_....,.,.atl'hlCNl'lloursCorrlp.,.,.FC.U.C Johnson fj, Controls