The URL can be used to link to this page

Home My WebLink About2270 CAMINO VIDA ROBLE; D; AS050245; Permit10/29/2020 Job Address: Permit Type: Parcel No: Lot#: Reference No.: PC#: Project Title: Applicant: AS050245 Permit Data City of Carlsbad Sprinkler Permit Permit No: AS050245 2270 CAMINO VIDA Status: ISSUED ROBLE SPRINK Applied 12/2/2005 2130504700 Approved: 12/2/2005 0 Issued: 12/2/2005 Inspector: SPEC SUITE, UNIT D FIRE SPRINKLER PLAN CHECK & INSPECTIONS Owner: AZTEC FIRE PROTECTION 8109 COMMERCIAL STREET 2270 CAMINO VIDA ROBLE LLC 685 TURQUOISE ST LA MESA, CA LA JOLLA CA (619) 464-5625 Fees($) Add'I Fees ($) Total($) Balance($) 120 0 120 0 - 1 /1 Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500 Series TY-FRB -2.8, 4.2, 5.6, and 8.0 K-factor Upright, Pendent, and Recessed Pendent Sprinklers Quick Response, Standard Coverage General Description The Series TY-FRB, 2.8, 4.2, 5.6, and 8.0 K-factor, Upright and Pendent Sprinklers described in this data sheet are quick response -standa~d cover- age, decorative 3 mm glass bulb type spray sprinklers designed for use in light or ordinary hazard, commercial occupancies such as banks, hotels, shopping malls, etc. The recessed version of the Series TY-FRB Pendent Sprinkler, where ap- plicable, is intended for use in areas with a finished ceiling. It uses either a two-piece Style 10 (1/2 inch NPT) or Style 40 (3/4 inch NPT) Recessed Es- cutcheon with 1/2 inch (12,7 mm) of recessed adjustment or up to 3/4 inch (19, 1 mm) of total adjustment from the flush pendent position, or a two-piece Style 20 (1/2 inch NPT) or Style 30 (3/4 inch NPT) Recessed Escutcheon with 1/4 inch (6,4 mm) of recessed adjust- ment or up to 1/2 inch (12,7 mm) of total adjustment from the flush pen- dent position. The adjustment provided by the ReGessed Escutcheon reduces the accuracy to which the fixed pipe drops to the sprinklers must be cut. Corrosion resistant coatings, where applicable, are utilized to extend the life of copper alloy sprinklers beyond that which would otherwise be ob.:. tained when · exposed to corrosive at- IMPORTANT Always refer to Technical Data Sheet TFP700 for the "INSTALLER WARNING" that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and in- stallation can permanently damage a sprinkler system or its compo- nents and cause the sprinkler to fail to operate in a fire situation or cause it to operate prematurely. Page 1 of 8 mospheres. Although corrosion resis- tant coated sprinklers have passed the standard corrosion tests of the appli- cable approval agencies, the testing is not representative of all possible cor- rosive atmospheres. Consequently, it is recommended that the end user be consulted with respect to the suitability of these coatings for any given corro- sive environment. The effects of ambi- ent temperature, concentration of chemicals, and gas/chemical velocity, should be considered, as a minimum, along with the corrosive nature of the chemical to which the sprinklers will be exposed. An intermediate level versions of the Series TY-FRB Pendent Sprinklers are detailed in Technical Data Sheet TFP356, and Sprinkler Guards are de- tailed in Technical Data Sheet TFP780 WARNINGS The Series TY-FRB Sprinklers de- scribed herein must be installed and maintained in compliance with this document, as well as with the applica- ble standards of the National Fire Pro- tection Association, in addition to the standards of any other authorities hav- ing jurisdiction. Failure to do so may impair the performance of these de- vices. The owner is responsible for maintain- ing their fire protection system and de- vices in proper operating condition. The installing contractor or sprinkler manufacturer should be contacted with any questions. Model/Sprinkler Identification Nu,nbers TY1131 - TY1231 - TY2131 - TY2231 - TY3131 - Upright 2.BK, 1/2"NPT Pendent 2.BK, 1/2"NPT Upright 4.2K, 1/2"NPT Pendent 4.2K, 1/2"NPT Upright 5.6K, 1/2"NPT JULY,2004 TY3231 - TY4131 - TY4231 - Pendent 5.6K, 1/2"NPT Upright 8.0K, 3/4"NPT Pendent 8.0K, 3/4"NPT Technical Data Approvals UL and C-UL Listed. FM, LPCB, and NYC Approved. (Refer to Table A for complete approval information including corrosion resis- tant status.) Maximum Working Pressure 175 psi (12,1 bar) Discharge Coefficient K = 2.8 GPM/psi1/2 (40,3 LPM/bar1l2) K = 4.2 GPM/psj1/2 (60,5 LPM/bar1l2) K = 5.6 GPM/psj1/2 (80,6 LPM/bar1l2) K = 8.0 GPM/psi1/2 (115,2 LPM/bar1l2) Temperature Ratings Refer to Table A and B TFP171 AOo:S-OZ-45 Page 2 of 8 ESCUTCHEON PLATE SEATING SURFACE 2-1/4" (57,2 mm) 7115• (11,1 mm) NOMINAL MAKE-IN l STYLE 10 or 20 RECESSED ESCUTCHEON ssu* DEFLECTOR 7115• (11,1 mm) NOMINAL MAKE-IN TFP171 .... ~ ... ~n1t~""t~a;,~.-./ 6 rt:::..::~--s ----4 t--,--2 3 WRENCH FLATS iiii~ 2-3/16. (55,6 mm) l SSP DEFLECTOR* PENDENT 1 -Frame 2 -Button 3-Sealing Assembly 2-7/8" (73,0mm) DIA __J RECESSED PENDENT 4-Bulb 5 -Compression Screw 6 -Deflector 7 -Bushing FIGURE 1 7 UPRIGHT CROSS SECTION * Temperature rating is indicated on deflector or adjacent to orifice seat on frame. ** Pipe thread connections per ISO 7 /1 can be provided on special request. QUICK RESPONSE SERIES TY-FRB UPRIGHT {TY1131) AND PENDENT {TY1231) SPRINKLERS 2.8 K-FACTOR, 1/2 INCH NPT ESCUTCHEON PLATE SEATING SURFACE 2-3/16. (55,6mm) 7/16" (11,1 mm) NOMINAL MAKE-IN ' STYLE 10 or 20 RECESSED ESCUTCHEON WRENCH FLATS ssu* DEFLECTOR 7115• (11,1 mm) NOMINAL MAKE-IN 2-3/16· (55,6 mm) SSP DEFLECTOR* PENDENT 2-7/8" (73,0 mm) DIA. __J RECESSED PENDENT 1/2" NPT** UPRIGHT l CROSS SECTION 4 -Bulb 6 -Deflector 1 -Frame 2 -Button 3 -Sealing Assembly 5 -Compression- Screw * Temperature rating is indicated on deflector or adjacent to orifice seat on frame. ** Pipe thread connections per ISO 7/1 can be provided on special request. FIGURE 2 QUICK RESPONSE SERIES TY-FRB UPRIGHT {TY2131) AND PENDENT {TY2231) SPRINKLERS 4.2 K-FACTOR, 1/2 INCH NPT Finishes Sprinkler: Refer to Table A and B Recessed Escutcheon: White Coated, Chrome Plated, or Brass Plated Physical Characteristics Frame . . . . . . . . . . . . . Bronze Button . . . . . . . . . Brass/Copper Sealing Assembly . . . . . . . . . . . . . . . Beryllium Nickel w/Teflont Bulb .............. Glass Compression Screw . . . . . Bronze Deflector . . . . . . Copper/Bronze Bushing (K=2.8) . . . . . . . Bronze Operation _ The glass Bulb contains a fluid which expands when exposed to heat. When the rated temperature is reached, the fluid expands sufficiently to shatter the glass Bulb, allowing the sprinkler to activate and water to flow. .:it! ai E ~ .= i a> 1ii O> Q) a: c 0 a.. :J 0 ~ TFP171 ESCUTCHEON PLATE SEATING SURFACE 2-3/16. {55,6 mm) 7/16. {11,1 mm) NOMINAL MAKE-IN I STYLE 10 or 20 RECESSED ESCUTCHEON WRENCH FLATS ssu* DEFLECTOR 7/16. {11,1 mm) NOMINAL MAKE-IN ~ 2-3/16· (55,6 mm) Page 3 of 8 SSP DEFLECTOR* PENDENT 2-7/8" (73,0 mm) DIA. -I RECESSED PENDENT 112• NPT** UPRIGHT ! CROSS SECTION 4 -Bulb 6 -Deflector 1 -Frame 2 -Button 3 -Sealing Assembly 5 -Compression Screw * Temperature rating is indicated on deflector or adjacent to orifice seat on frame. **Pipe thread connections per ISO 7/1 can be provided on special request. FIGURE 3 QUICK RESPONSE SERIES TY-FRB UPRIGHT {TY3131) AND PENDENT (TY3231) SPRINKLERS 5.6 K-FACTOR, 1/2 INCH NPT ESCUTCHEON PLATE SEATING SURFACE 2-5/16. {58,7mm) 112• {12,7 mm) NOMINAL MAKE-IN _J_ STYLE 30 or 40 RECESSED ESCUTCHEON WRENCH FLATS ssu* DEFLECTOR 112· {12,7 mm) NOMINAL MAKE-IN 2-114• (57,2 mm) 2 3 SSP DEFLECTOR* PENDENT 2-7/8" {73,0mm) DIA J RECESSED PENDENT 3/4"NPT~ UPRIGHT CROSS SECTION 4-Bulb 6 -Deflector 1 -Frame 2 -Button 3 -Sealing Assembly 5 -Compression Screw * Temperature rating is indicated on deflector or adjacent to orifice seat on frame. **Pipe thread connections per ISO 7/1 can be provided on special request. FIGURE4 QUICK RESPONSE SERIES TY-FRB UPRIGHT (TY4131) AND PENDENT {TY4231) SPRINKLERS 8.0 K-FACTOR, 314 INCH NPT Design Criteria The Series TY-FRB Pendent and Up- right Sprinklers are intended for fire protection systems designed in ac- cordance with the standard installation rules recognized by the applicable Listing or Approval agency (e.g., UL Listing is based on the requirements of NFPA 13, and FM Approval is based on the requirements of FM's Loss Pre- vention Data Sheets). Only the Style 10, 20, 30, or 40 Recessed Escutch- eon, as applicable, is to be used for recessed pendent installations. Installation The Series TY-FRB Sprinklers must be installed in accordance with the follow- ing instructions: NOTES Do not install any bulb type sprinkler if the bulb is cracked or there is a loss of liquid from the bulb. With the sprinkler Page 4 of 8 SPRINKLER FINISH (See Note 7) K TYPE TEMP. BULB NATURAL I CHROME I WHITE"- LIQUID BRASS PLATED POL VESTER 135°F/57°C Orange PENDENT 155°F/68°C Red (TY1231) 1,2,3,5 and 175°F/79°C Yellow UPRIGHT 200°F/93°C Green 2.8 (TY1131) 286°F/141 °C Blue 112· NPT 135°F/57°C Orange RECESSED 155°F/68°C Red PENDENT (TY1231)* 175°F/79°C Yellow Figure 5 200°F/93°C Green 1, 2, 5 135°F/57°C Orange RECESSED 155°F/68°C Red PENDENT (TY1231)** 175°F/79°C Yellow Flgure6 200°F/93°C Green 135°F/57°C Orange PENDENT 155°F/68°C Red (TY2231) and 175°F/79°C Yellow UPRIGHT 200°F/93°C Green 4.2 (TY2131) 286°F/141 °C Blue 112· 1, 2 NPT 135°F/57°C Orange RECESSED 155°F/68°C Red PENDENT (TY2231)* 175°F/79°C Yellow Figure 7 200°F/93°C Green 135°F/57°C Orange RECESSED 155°F/68°C Red PENDENT (TY2231)** 175°F/79°C Yellow Figures 200°F/93°C Green NOTES: 1. Listed by Underwriters Laboratories, Inc. (UL) as Quick Response Sprinklers. 2. Listed by Underwriters Laboratories, Inc. for use in Canada (C-UL) as Quick Response Sprinklers. 3. Approved by Factory Mutual Research Corporation (FM) as Quick Response Sprin- klers. 5. Approved by the City of New York under MEA 354-01-E. 7. Where Polyester Coated Sprinklers are noted to be UL and C-UL Listed, the sprin- klers are UL and C-UL Listed as Corrosion Resistant Sprinklers. * Installed with Style 10 (112• NPn or Style 40 (3/4• NPT) 3/4• Total Adjustment Recessed Escutcheon, as applicable. ** Installed with Style 20 (1/2• NPT) or Style 30 (3W NPn 112• Total Adjustment Recessed Escutcheon, as applicable. *** Frame and Deflector only. Listings and approvals apply to color (Special Order). N/ A: Not Available TABLE A LABORATORY LISTINGS AND APPROVALS 2.8 AND 4.2 K-FACTOR SPRINKLERS held horizontally, a small air bubble should be present. The diameter of the air bubble is approximately 1/16 inch (1,6 mm) for the 135°F/57°C to 3/32 inch (2,4 mm) for the 286°F/141°C temperature ratings. A leak tight 1/2 inch NPT sprinkler joint should be obtained with a torque of 7 to 14 ft.lbs. (9,5 to 19,0 Nm). A maxi- mum of 21 ft. lbs. (28,5 Nm) of torque may be used to install sprinklers with 1/2 NPT connections. A leak tight 3/4 TFP171 inch NPT sprinkler joint should be ob- tained with a torque of 10 to 20 ft.lbs. (13,4 to 26,8 Nm). A maximum of 30 ft.lbs. ( 40, 7 Nm) of torque is to be used to install sprinklers with 3/4 NPT con- nections. Higher levels of torque may distort the sprinkler inlet and cause leakage or impairment of the sprinkler. Do not attempt to make-up for insuffi- cient adjustment in the escutcheon plate by under-or over-tightening the sprinkler. Readjust the position of the sprinkler fitting to suit. The Series TY-FRB Pendent and Up- right Sprinklers must be installed in accordance with the following instruc- tions. Step 1. Pendent sprinklers are to be installed in the pendent position, and upright sprinklers are to be installed in the upright position. Step 2. With pipe thread sealant ap- plied to the pipe threads, hand tighten the sprinkler into the sprinkler fitting. Step 3. Tighten the sprinkler into the sprinkler fitting using only the W-Type 6 Sprinkler Wrench (Ref. Figure 13). With reference to Figures 1 , 2, 3, and 4, the W-Type 6 Sprinkler Wrench is to be applied to the sprinkler wrench flats. The Serles TY-FRB Recessed Pen- dent Sprinklers must be installed in accordance with the following instruc- tions. Step A. After installing the Style 10. 20, 30, or 40 Mounting Plate, as appli- cable, over the sprinkler threads and with pipe thread sealant applied to the pipe threads, hand tighten the sprin- kler into the sprinkler fitting. Step B. Tighten the sprinkler into the sprinkler fitting using only the W-Type 7 Recessed Sprinkler Wrench (Ref. Figure 14). With reference to Figure 1, 2, 3, and 4, the W-Type 7 Recessed Sprinkler Wrench is to be applied to the sprinkler wrench flats. Step C. After the ceiling has been in- stalled or the finish coat has been ap- plied, slide on the Style 10, 20, 30, or 40 Closure over the Series TY-FRB Sprinkler and push the Closure over the Mounting Plate until its flange comes in contact with the ceiling. TFP171 Page 5 of 8 SPRINKLER FINISH (See Note 8) K TYPE TEMP. BULB NATURAL I CHROME WHITe** LEAD LIQUID BRASS PLATED POLYESTER COATED 135°F/57°C Orange PENDENT 155°F/68°C Red (TY3231) 1,2,3,4,5,6, 7 1, 2, 3, 5 and 175°Fll9°C Yellow UPRIGHT 200°F/93°C Green 5.6 (TY3131) 286°F/141°C Blue 112· NPT 135°F/57°C Orange RECESSED 155°F/68°C Red PENDENT 1, 2, 4, 5 N/A (TY3231)* 175°Fll9°C Yellow Agure9 200°F/93°C Green 135°F/57°C Orange RECESSED 155°F/68°C Red PENDENT 1,2,3,4,5 1,2,4,5 N/A (TY3231,-175°Fll9°C Yellow Agure 10 200°F/93°C Green 135°F/57°C Orange PENDENT 155°F/68°C Red (TY4231) 1,2,5 and 175°Fll9°C Yellow 1,2,3,4,5,6, 7 UPRIGHT 200°F/93°C Green 8.0 (TY4131) 286°F/141°C Blue 3W NPT 135°F/57°C Green RECESSED 155°F/68°C Orange PENDENT 1, 2, 4, 5 NIA (TY4231)* 175°Fll9°C Red Figure 11 200°F/93°C Yellow 135°F/57°C Orange RECESSED 155°F/68°C Red PENDENT 1,2,3,4,5 N/A (TY4231)** 175°Fll9°C Yellow Figure 12 200°F/93°C Green NOTES: 1. Listed by Underwriters Laboratories, Inc. (UL) as Quick Response Sprinklers. 2. Listed by Underwriters laboratories, Inc. for use in Canada (C-UL) as Quick Response Sprinklers. 3. Approved by Factory Mutual Research Corporation (FM) as Quick Response Sprinklers. 4. Approved by the Loss Prevention Certification Board (LPCB Ref. No. 007k/04) as Quick Response Sprinklers; however, the LPCB does not rate the thermal sensitivity of recessed sprinklers. 5. Approved by the City of New York under MEA 354-01-E. 6. VdS Approved (For details contact Tyco Fire & Building Products, Enschede, Netherlands, Tel. 31-53-428-4444/Fax 31-53-428-3377). 7. Approved by the Loss Prevention Certification Board (LPCB Ref. No. 094a/06) as Quick Response Sprinklers. 8. Where Polyester Coated and Lead Coated Sprinklers are noted to be UL and C-Ul listed, the sprinklers are UL and C-UL listed as Corrosion Resistant Sprinklers. Where lead Coated Sprinklers are noted to be FM Approved, the sprinklers are FM Approved as a Corrosion Resistant Sprinklers. * Installed with Style 10 (1/2• NPT) or Style 40 (3/4• NPT) 314• Total Adjustment Recessed Escutcheon, as applicable. ** Installed with Style 20 (112• NPT) or Style 30 (3/4• NPT) 112• Total Adjustment Recessed Escutcheon, as applicable. *** Frame and Deflector only. listings and approvals apply to color (Special Order). N/ A: Not Available TABLES LABORATORY LISTINGS AND APPROVALS 5.6 AND 8.0 K-FACTOR SPRINKLERS Page 6 of 8 TFP171 5/8±1/4" (15,9±6,4 mm) FACE OF SPRINKLER FITTING MOUNTING SURFACE 2-7/8" DIA. ;i (73,0mm) 2-1/4" DIA. --:I (57.2mm) r I 3/4" 19,1 mm 1/4" (6,4 mm) MOUNTING PLATE 1/8" =Im) 1/2±1/8" (12,7±3,2 mm) FACE OF SPRINKLER FITTING 2-7/8" DIA. ;i (73,0mm) 2-1/4" DIA. --j (51.2mm) r I 1/2" 12,7 mm 1/4" (6,4 mm) MOUNTING PLATE 1/8" (3,2mm) \ ~~~-I. .;.,c.,,r;..~~=~~::.=-:i~, _j_ MOUNTING SURFACE CLOSURE SERIES TY-FRB 1-5/16" (33,3 mm 13/16" (20,6 mm) CLOSURE SERIES TY-FRB 1-5/16" 33,3 mm 1-1/16" (27,0 mm) FIGURES RGURE6 SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 314 INCH TOTAL ADJUSTMENT STYLE 10 RECESSED ESCUTCHEON SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 20 RECESSED ESCUTCHEON 2.8 K-FACTOR, 1/2 INCH NPT 2.8 K-FACTOR, 1/2 INCH NPT 5/8±1/4" (15,9±6.4 mm) FACE OF SPRINKLER FITTING MOUNTING SURFACE CLOSURE 2-7/8" DIA. ;i (73,0 mm) 2-1/4" DIA. 7 (57,2mm) r I SERIES TY-FRB FIGURE7 3/4" (19,1 mm) 1/4" (6,4 mm) MOUNTING PLATE 1-1/4" (31,8 mm 3/4" (19,1 mm) 1/2±1/8" (12,7±3,2 mm) FACE OF SPRINKLER FITTING 2-7/8" DIA. ;i (73,0mm) 2-1/4" DIA. 7 (57,2mm) r I 1/2" (12,7 mm 1/4" (6,4 mm) MOUNTING PLATE 1/8" (3,2mm) \ ~d.111~~=1 ~~-t:::;:;;.:::j;~ MOUNTIN SURFAC CLOSURE SERIES TY-FRB FIGURES 1-1/4" 31,8 mm 1" (25,4 mm) SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 314 INCH TOTAL ADJUSTMENT STYLE 10 RECESSED ESCUTCHEON SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 20 RECESSED ESCUTCHEON 4.2 K-FACTOR, 1/2 INCH NPT 4.2 K-FACTOR, 1/2 INCH NPT Care and Maintenance The Series TY-FRB Sprinklers must be maintained and serviced in accord- ance with the following instructions: NOTES Before closing a fire protection system main control valve for maintenance work on the fire protection system that it controls, permission to shut down the affected fire protection system must be obtained from the proper authorities and all personnel who may be affected by this action must be notified. Absence of an escutcheon, which is used to cover a clearance hole, may delay the time to sprinkler operation in a fire situation. Sprinklers that are found to be leaking or exhibiting visible signs of corrosion must be replaced. Automatic sprinklers must never be painted, plated, coated or otherwise altered after leaving the factory. Modi- fied sprinklers must be replaced. Sprinklers that have been exposed to corrosive products of combustion, but have not operated, should be replaced if they cannot be completely cleaned by wiping the sprinkler with a cloth or by brushing it with a soft bristle brush. Care must be exercised to avoid dam- age to the sprinklers -before, during, and after installation. Sprinklers dam- aged by dropping, striking, wrench twisVslippage, or the like, must be re- placed. Also, replace any sprinkler that has a cracked bulb or that has lost liquid from its bulb. (Ref. Installation Section). Frequent visual inspections are rec- ommended to be initially performed for corrosion resistant coated sprinklers, after the installation has been com- pleted, to verify the integrity of the cor- rosion resistant coating. Thereafter, annual inspections per NFPA 25 should suffice; however, instead of in- specting from the floor level, a random sampling of close-up visual inspec- tions should be made, so as to better determine the exact sprinkler condi- TFP171 5/8±1/4" (15,9±6,4 mm) FACE OF SPRINKLER FITTING MOUNTING SURFACE CLOSURE 2-7/8" DIA. ;l (73,0mm) 2-1/4" DIA. --:i (57,2mm) r I SERIES TY-FRB RGURE9 314" 19,1 mm) 1/4" (6,4 mm) MOUNTING PLATE 1-1/4" (31,8 mm) 314" (19,1 mm) SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT STYLE 10 RECESSED ESCUTCHEON 5.6 K-FACTOR, 112 INCH NPT 5/8±1/4" (15,9±6,4 mm) FACE OF SPRINKLER FITTING 2-7/B"DIA.11 (73,0mm) 2-1/4" DIA. -1 (57,2 mm) _J I 3/4" (19,1 mm) 1/4" (6,4 mm) MOUNTING PLATE MOUNTING SURFACE CLOSURE SER .. l~ESa::::a::z::,ii!ba . 1-511~ l~,J TY-FRB 13116" (20,6 mm) FIGURE 11 SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 314 INCH TOTAL ADJUSTMENT STYLE 40 RECESSED ESCUTCHEON 8.0 K-FACTOR, 3/4 INCH NPT tion and the long term integrity of the corrosion resistant coating, as it may be affected by the corrosive conditions present. 1/2±1/8" (12,7±3,2 mm) FACE OF SPRINKLER FITTING \ MOUNTING SURFACE CLOSURE 2-7/8" DIA. ;l (73,0mm) 2-1/4" DIA. --:i (57,2mm) r I SERIES TY-FRB FIGURE 10 Page 7 of 8 1/2" 12,7 mm 1/4" (6,4 mm) MOUNTING PLATE 1-1/4" (31,8mm) 1• (25,4mm) SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 20 RECESSED ESCUTCHEON 5.6 K-FACTOR, 1/2 INCH NPT 1/2±1/8" (12,7±3,2 mm) FACE OF SPRINKLER FITTING \ MOUNTING SURFACE CLOSURE 2-7/8" DIA. (73,0mm) 2-1/4" DIA. (57,2mm) SERIES TY-FRB FIGURE 12 1/2" 12,7 mm) 1/4" (6,4 mm) MOUNTING PLATE 1-5/16" 33,3 mm 1-1/16" (27,0 mm) SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 112 INCH TOTAL ADJUSTMENT STYLE 30 RECESSED ESCUTCHEON 8.0 K-FACTOR, 314 INCH NPT WRENCH RECESS The owner is responsible for the in- spection, testing, and maintenance of their fire protection system and de- vices in compliance with this docu- ment, as well as with the applicable standards of the National Fire Protec- tion Association (e.g., NFPA 25), in addition to the standards of any other authorities having jurisdiction. The in- stalling contractor or sprinkler manu- facturer should be contacted relative to any questions. WRENCH RECESS (END "A" USED FOR 112• NPT MODELS) It is recommended that automatic sprinkler systems be inspected, tested, and maintained by a qualified Inspection Service in accordance with WRENCH RECESS (END •s• USED FOR 3W NPT MODELS) FIGURE 13 W-TYPE 6 SPRINKLER WRENCH local requirements and/or national codes. PUSH WRENCH INTO ENSURE ENGAGEMENT WITH SPRINKLER WRENCHING AREA FIGURE 14 W-TYPE 7 RECESSED SPRINKLER WRENCH Page 8 of 8 TFP171 P/N 57-XXX-X-XXX I I I MODEUSIN TEMPERATURE RATING SPRINKLER 330 2.8K UPRIGHT (1/2.NPl) TY1131 135 135°F/57°C 331 2.8K PENDENT (1/2.NPT} TY1231 1 NATURAL BRASS 155 155°F/68°C 340 4.2K UPRIGHT (1/2.NPT} TY2131 4 WHITE POL VESTER 175 175°F/79°C 341 4.2K PENDENT (1/2.NPl) TY2231 3 WHITE (RAL9010)* 200 200°F/93°C 370 5.6K UPRIGHT (1/2.NPT} TY3131 9 CHROME PLATED 286 286°F/141°C 371 5.6K PENDENT (1/2.NPT} TY3231 7 LEAD COATED 390 8.0K UPRIGHT (3/4.NPl) TY4131 391 8.0K PENDENT (3/4.NPT} TY4231 * Eastern Hemisphere sales only. TABLEC PART NUMBER SELECTION SERIES TY-FRB PENDENT AND UPRIGHT SPRINKLERS Li,nited Warranty Products manufactured by Tyco Fire Products are warranted solely to the original Buyer for ten (10) years against defects in material and work- manship when paid for and properly installed and maintained under normal use and service. This warranty will ex- pire ten ( 10) years from date of ship- ment by Tyco Fire Products. No war- ranty is given for products or components manufactured by compa- nies not affiliated by ownership with Tyco Fire Products or for products and components which have been subject to misuse, improper installation, corro- sion, or which have not been installed, maintained, modified or repaired in ac- cordance with applicable Standards of the National Fire Protection Associa- tion, and/or the standards of any other Authorities Having Jurisdiction. Mate- rials found by Tyco Fire Products to be defective shall be either repaired or replaced, at Tyco Fire Products' sole option. Tyco Fire Products neither as- sumes, nor authorizes any person to assume for it, any other obligation in connection with the sale of products or parts of products. Tyco Fire Products shall not be responsible for sprinkler system design errors or inaccurate or incomplete information supplied by Buyer or Buyer's representatives. IN NO EVENT SHALL TYCO FIRE PRODUCTS BE LIABLE, IN CON- TRACT, TORT, STRICT LIABILITY OR UNDER ANY OTHER LEGAL THE- ORY, FOR INCIDENTAL, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LABOR CHARGES, RE- GARDLESS OF WHETHER TYCO FIRE PRODUCTS WAS INFORMED ABOUT THE POSSIBILITY OF SUCH DAMAGES, AND IN NO EVENT SHALL TYCO FIRE PRODUCTS' LI- ABILITY EXCEED AN AMOUNT EQUAL TO THE SALES PRICE. THE FOREGOING WARRANTY IS MADE IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESS OR IMPLIED. INCLUDING WARRANTIES OF MERCHANTABILITY AND FIT- NESS FOR A PARTICULAR PUR- ffJS.E. Ordering Procedure ®Dflt•i}fo~ l@cal distributor for avail- abifftsJ_indicate the tufr' product name. Refer to the Price List for complete listing of Part Numbers. Sprinkler Assemblies with NPT Thread Connections: Specify: (Specify Model/SIN), Quick Response, (specify K-factor), (specify temperature rating), Series TY-FRB (specify Pendent or Upright) Sprinkler with (specify type of finish or coating), P/N (specify from Table C). Recessed Escutcheon: Specify: Style (specify) Recessed Es- cutcheon with (specify finish), P/N (specify). 1/2" (15 mm) Style 10 Chrome Plated ............ PIN 56-701-9-010 White Coated ............. PIN 56-701-4-010 White RAL9010* ........... P/N 56-701-3-010 Brass Plated .............. PIN 56-701-2-010 1/2" (15 mm) Style 20 Chrome Plated . . . . . . . . . . . . PIN 56-705-9-010 White Coated ............. PIN 56-705-4-010 White RAL9010• ........... PIN 56-705-3-010 Brass Plated . . . . . . . . . . . . . . P/N 56-705-2-01 O 3/4" (20 mm) Style 30 Chrome Plated . . . . . . . . . . . . PIN 56-705-9-011 White Coated ............. P/N 56-705-4-011 White RAL9010• ........... P/N 56-705-3-011 Brass Plated .............. P/N 56-705-2-011 314" (20 mm) Style 40 Chrome Plated ............ P/N 56-700-9-010 White Coated ............. P/N 56-700-4-010 White RAL9010• . . . . . . . . . . . PIN 56-700-3-010 Brass Plated .............. PIN 56-700-2-010 * Eastern Hemisphere sales only. Sprinkler Wrench: Specify: W-Type 6 Sprinkler Wrench, P/N 56-000-6-387. Specify: W-Type 7 Sprinkler Wrench, P /N 56-850-4-001 . TYCO FIRE PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446