Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
2478 IMPALA DR; ; FA120036; Permit
7/28/22, 12:22 PM FA120036 Permit Data City of Carlsbad Fire Alarm Permit Job Address: 2478 IMPALA DR Permit Type: FALARM Parcel No: 2090412800 Lot#: 0 Reference No.: Permit No: FA 120036 Status: APPROVED Applied 9/11/2012 Approved: 10/1/2012 Issued: 10/1/2012 PC #: Inspector: Project Title: LA POSADA MENS SHELTER NEW FIRE ALARM SYSTEM FOR AN R-1 MULTI-BUILDING COMPLEX Applicant: JJJ ENTERPRISES 533 S VINEWOOD ST ESCONDIDO CA 760-7 4 7 -3050 Fees($) 708 about:blank Add'I Fees ($) 0 Owner: CATHOLIC CHARITIES DIOCESE OF SAN DIEGO 349 CEDAR ST SAN DIEGO CA Total($) 708 Balance($) 0 1/1 P arsRey C«J>nsuRting 350 '\"AT est 9th Awenue, Suite 206 Escouclido, California 92025-5053 Telephone (760) 745-6Jl8l FaxGbO} 745-0537 September 5, 2012 Fire Code Official City of Carlsbad Fire Department Office of Fire Protection Services 1635 Faraday A venue Carlsbad, Ca lifornia 92008 Subject: Plan Review for La Posada Men's Shelter Alarm System, 2478 Impala Drive, Carlsbad, California Dear Sir: We have reviewed the submittal as prepared by JJJ Enterprises. Ba.::;ed on our review it is our opinion that the submittal is in substantial conformance with the applicable codes and standards in force at this time, including local adopted ordinances. Further submittal should not be required. Sincerely, P~LEY -c1~?lt~~ ~Wagone~T Office Manager Encl (I) Working Drawings -3 sets (2) Material Submittals -2 sets (3) Review Comments -1 set Note: A copy of this letter has been transmitted via e-mail to JJJ Enterprises on September 5, 2012 file \C\l)ocu111e11ts and Settings\Ken\Rev2I2323.01 .wpd La Posada Men's Shelter Alarm System Review Comments. Page 2 Review Comments La Posada Men's Shelter Alarm System, 2478 Impala Drive, Carlsbad, California We strongly recommend the following operational tests be performed once the system installation has been completed. a. A "power off' test, where the normal power supply is shut off, and the system is left to function on battery power alone for a period of24 hours, at which time the system should still be functioning and operational. b. At the end of the end of the above test, prior to the primary power being restored, the system should be placed in an "alarm" condition for a period of not less than five minutes, during which time all notification appliances, including the off-station notification, are to function as designed. c. Once the two prior tests have been completed, the current level in the batteries should be checked, the primary power restored, and at the end of 48 hours the current level checked again to verify that the charging function of the panel is both operational, and able to recharge the batteries within the time period specified by NFPA-72. d. Once the test in item "c" has been complet'ed, one of the leads to the battery should be disconnected, to determine that the system will provide notification of an "off-normal" power condition to the monitoring company. FfREALARM SECURITY LOW VOLTAGE SYSTEMS LA POSADA MEN'S SHELTER 2478 IMPALA DRIVE CARLSBAD, CA 92008 FIRE ALARM SYSTEM MATERIAL DATA SHEETS r ,, .... ,. i'' 111, 11.1\l' h, l'll lL\i"\\,·d ,,,, 11'p.11L·111 u •111pl1.111LL' \\ 1th 11 · , llll'l'flt ,q1pl1c,1t->k uid\', and ,t,tlld,11d, 111 fmll' 111 thL , ,11,c.l1l1111n Till' ,l\\Jll'J PrLn11tr.1L lnr 111a, dttl11L this IL'\ IL'.\\ 111 . uppurt pf ,111 appl1L ,ll1\lt1 fllt .1 huiid111g pl'.1 :nil "1th the L"<ptl'"-" umkr,t.111d111g that this rL'\ 11·,, 111 nn way relti:, es thl.! m, ncr or <.:n11t1 a<.:tor nr thL'lr p1ofessional enginl'er nr ard1ite<.:t lor snk resp(1ns1htl1t~ fur full <.:n111pl1an<.:L' with saic.J <.:ntks and standard,. including the building entk or for any re,prnh1h1'1y f(lr dl'I ,l·1\'nc·1L'' l'IT11r,. 11111is:-.1011:-. nr 111:~li~L'lll"c 111 thcsl' ,, ... • •1,·11,, •11 ntll ,1111cd 111 1h1, re\ i1•\,. □ l<I-.COil.·11'\H: l>Al'Pt<O\..\I. AS '.\IOTl--1) -..... ,.., n c::a -a ~ LA POSADA MEN'S SHELTER 2478 IMPALA DRIVE CARLSBAD, CA 92008 FIRE ALARM SYSTEM BILL OF MATERIALS NOTIFIER NFW2-100 FIRE ALARM CONTROL PANEL CSFM# 7165-0028:0235 NOTIFIER N-ANN-80 REMOTE FIRE ANNUNCIATOR CSFM# 7120-0028:0240 NOTIFIER NP-100 ADDRESSABLE SMOKE DETECTOR CSFM# 7272-0028:231 NOTIFIER NOT-BG12LX MANUAL PULL STATION CSFM# 7150-0028: 199 NOTIFIER NMM-100P ADDRESSABLE MINIATURE MONITOR MODULE CSFM# 7300-0028:230 NOTIFIER NC-100R RELAY MODULE CSFM# 7300-0028:230 SYSTEM SENSOR DNR DUCT DETECTOR CSFM# 3242-1653:0209 WHEELOCK HSR/C CEILING AND WALL MOUNTED HORN/STROBES (RED) CSFM# 7125-0785:168 WHEELOCK STR WALL MOUNTED STROBES (RED) CSFM# 7125-0785:168 WHEELOCK STR ASWP-2475W-FR WEATHERPROOF HORN/STROBES CSFM# 7125-0785:0131 F ireWarden-100-2(E) Rev 3 Intelligent Addre_ssable FACP General The Notifier FireWarden-100-2 Rev 3 (NFW2-100) with Version 5.0 firmware is a combination FACP (Fire Alarm Control Panel) and DACT (Digital Alarm Communicator/Transmitter) all on one circuit board. This compact intelligent addressable control panel has an extensive list of powerful features. The SLC (Signaling Line Circuit) of the FireWarden-100-2 Rev 3 operates using a Rapid Group Polling communication protocol technology that polls multiple devices simultaneously for a quicker device response time.This patented technology allows a fully-loaded panel with up to 198 devices to report an incident and activate the notification circuits in under 10 seconds. With this improved polling, devices can be wired on standard twisted, unshielded wire up to a distance of 10,000 feet. The 's quick-remove chassis protects the electronics during con- struction. The backbox can be installed allowing field wiring to be pulled. When construction is completed, the electronics can be quickly installed with just two bolts. New features for Rev 3 with Version 5.0 firmware include removable terminal blocks, improved transient protection, addi- tional secondary ANN-BUS, and increased power for the reset- table and remote sync outputs. Available accessories include ANN-BUS devices as well as ACS LEO, graphic and LCD annunciators, and reverse polarity/city box transmitter. The integral DACT transmits system status (alarms, superviso- ries, troubles, AC loss, etc.) to a Central Station via the public switched telephone network. It also allows remote and local pro- gramming of the control panel using the PS-Tools Upload/Down- load utility. In addition, the control panel may be programmed or interrogated off-site via the public switched telephone network. Any personal computer with Windows® XP or greater, a com- patible modem, and PS-Tools-the Upload/Download software kit-may serve as a Service Terminal. This allows download of the entire program or upload of the entire program, history file, walktest data, current status and system voltages. The panel can also be programmed through the FACP's keypad or via a standard PS-2 computer keyboard, which can be plugged directly into the printed circuit board. This permits easy typing of address labels and other programming information. Version 5.0 firmware supports the following: Primary and Sec- ondary ANN-bus devices, NP-A100, USB port, NAC circuit diag- nostics, a new report has been added to the walk-test that lists untested devices, new device types added: audio telephone type code for N FV-25/50ZST, Photo Supervisory and auto-reset- table Drill (non-latching). The FireWatch Series internet monitoring modules IPDACT-2 and IPDACT-2UD permit monitoring of alarm signals over the Internet saving the monthly cost of two dedicated business tele- phone lines. Although not required, the secondary telephone line may be retained providing backup communication over the public switched telephone line. NOTE: Unless otherwise specified, the term "FireWarden-100-2" is used in this document to refer to both the FireWarden-100-2 and the FireWarden-100-2E FACPs (Fire Alarm Control Panels). Like- wise, "NFW2-100" refers to NFW2-100E as well. Features • Listed to UL standard 864, 9th edition. • On-board DACT. DN-60602:A 1 ~NOTIFIER® by Honeywell • Remote site or local USB port upload/download, using PS- Tools. • Four (4) Style Y (Class B) NAC circuits, which can be con- verted to four (4) Style Z (Class A) circuits with optional ZNAC-92 converter module. (Up to 6.0 amps total NAC power when using optional XRM-24B.) • Selectable strobe synchronization for System Sensor, Whee- lock, and Gentex devices. • Remote Acknowledge, Silence, Reset and Drill via address- able monitor modules or FDU-80, N-ANN-80 or Legacy ACS Annunciators. • ANN-BUS for connection to following optional modules (cannot be used if ACS annunciators are used): -N-ANN-80(-W) Remote LCD Annunciator -N-ANN-I/O LED Driver -N-ANN-S/PG Printer Module -N-ANN-RLY Relay Module -N-ANN-LED Annunciator Module -N-ANN-RLED Annunciator Module alarms only -ROME Relay Option Module Enclosure • ACS & Terminal-mode Annunciators: -ACS Annunciators: Up to 32 Legacy ACM Series annuncia- tors (ACM-16AT or ACM-32 series). Cannot be used if ANN-BUS devices are used. -Terminal-mode Annunciators: Up to 32 Legacy FDU-80 annunciators. • EIA-232 printer/PC interface (variable baud rate) on main cir- cuit board, for use with optional UL-listed printer PRN-6. • Integral SO-character LCD display with backlighting. • Real-time clock/calendar with automatic daylight savings control. • Detector sensitivity test capability (NFPA 72 compliant). DN-60602:A1 • 12/07/2010-Page 1 of 6 • History file with 1,000-event capacity. • Maintenance alert warns when smoke detector dust accumu- lation is excessive. • Automatic device type-code verification. • One person audible or silent walk test with walk-test log and printout. • Point trouble identification. • Waterflow (nonsilenceable) selection per monitor point. • System alarm verification selection per detector point. • PAS (Positive Alarm Sequence) and presignal delay per point (NFPA 72 compliant). NOTE: Only detectors may participate in PAS. SLC LOOP: • SLC can be configured for NFPA Style 4, 6, or 7 operation. • SLC supports up to 198 addressable devices per loop (99 detectors and 99 monitor, control, or relay modules). • SLC loop maximum length 10,000 ft. (3,000 m.). See installation manual for wire tables. NOTIFICATION APPLIANCE CIRCUITS (NACS): • Four onboard NACs with additional NAC capability using out- put control modules (NC-100). The four Class B NACs can be converted to four Class A NACs with optional ZNAC-92 converter module. • Silence Inhibit and Auto Silence timer options. • Continuous, March Time, Temporal or California code for main circuit board NACs with two-stage capability. • Selectable strobe synchronization per NAC. • 2.5 amps maximum per each NAC circuit. NOTE: Maximum 24VOC system power output is shared among all NAG circuits and 24VOC special-application auxiliary power outputs. Total available output is 3.0 amps. Using the optional XRM-24B transformer increases 24VDC output to 6.0 amps. PROGRAMMING AND SOFTWARE: • Autoprogram (learn mode) reduces installation time. • Custom English labels (per point) may be manually entered or selected from an internal library file. • Three Form-C relay outputs (two programmable). • 99 software zones. • Continuous fire protection during online programming at the front panel. • Program Check automatically catches common errors not linked to any zone or input point. • OFFLINE PROGRAMMING: Create the entire program in your office using a Windows®-based software package (N FW2-100 requires PS-Tools Programming software, avail- able on www.magni-fire.com). Upload/download system pro- gramming locally to the NFW2-100 Rev 3 in less than one minute. • USB upload/download programming with standard Male-A to Male-B cable. User Interface LED INDICATORS • AC Power (green) • Fire Alarm (red) • Supervisory (yellow) • Alarm Silenced (yellow) • System Trouble (yellow) • Maintenance/Presignal (yellow) • Disabled (yellow) • Battery Fault (yellow) Page 2 of 6 -DN-60602:A1 • 12/07/2010 • Ground Fault (yellow) KEYPAD CONTROLS • Acknowledge/Step • Alarm Silence • Drill • System Reset (lamp test) • 16-key alpha-numeric pad (similar to telephone keypad) • 4 cursor keys • Enter Product Line Information NFW2-100: FireWarden-100-2 Rev 3 198-point addressable Fire Alarm Control Panel, one SLC loop. Includes SO-character LCD display, single printed circuit board mounted on chassis, and cabinet. 120 VAC operation. NFW2-1 00R: Same as NFW2-100, except in a red backbox. NFW2-100E: Same as NFW2-100, except with 240 VAC opera- tion. 4XTM Reverse Polarity Transmitter Module: Provides super- vised output for local energy municipal box transmitter, alarm, and trouble. ZNAC-92: Optional converter module which converts four (4) Style Y (Class B) NAC circuits to four (4) Style Z (Class A) cir- cuits. PS Tools: Programming software for Windows®-based PC computer (cable not included), available on www.firelite.com . DP-96928: Optional dress panel for FireWarden-100-2 Rev 3. TR-CE-B: Optional trim Ring for semi-flush mounting. BB-26: Battery backbox, holds up to two 26 AH batteries and CHG-75. NFS-LBB: Battery box, houses two 55 AH batteries. CHG-75: Battery charger for lead-acid batteries with a rating of 25 to 75 AH. CHG-120: Remote battery charging system for lead-acid batter- ies with a rating of 55 to 120 AH. Requires additional NFS-LBB for mounting. NOTE: CHG-120 or CHG-75 required for batteries larger than 18AH. BAT Series: Batteries, see data sheet DN-6933. XRM-24B(E): Optional transformer. Increases system power output to 6.0 amps. Use XRM-24BE with FireWarden-100-2E Rev 3. PAT/PK-CABLE: Cable printer/personal computer interface cable; required for printer or for local upload/download program- ming and updating panel firmware. PRN-6: UL listed compatible event printer. Uses tra~tor-fed paper. IPDACT-2/2UD, IPDACT Internet Monitoring Module: Mounts in bottom of enclosure with optional mounting kit (PN IPBRKT). Connects to primary and secondary DACT telephone output ports for internet communications over customer provided ether- net internet connection. Requires compatible Teldat VisorALARM Central Station Receiver. Can use DHCP or static IP. (See data sheet DN-60408 for more information.) IPBRKT: Mounting kit for IPDACT-2/2UD in common enclosure. IPSPLT: Y-adaptor option allows connection of both panel dialer outputs to one IPDACT-2/2UD cable input. COMPATIBLE ANNUNCIATORS N-ANN-80(-W): LCD Annunciator is a remote LCD annunciator that mimics the information displayed on the FACP LCD display. Recommended wire type is un-shielded. (Basic model is black; order -W version for white; see DN-7114.) N-ANN-LED: Annunciator Module provides three LEDs for each zone: Alarm, Trouble and Supervisory. Ships with red or black enclosure (see DN-60242). N-ANN-RLED: Provides alarm (red) indicators for up to 30 input zones or addressable points. (See DN-60242). N-ANN-RLY: Relay Module, which can be mounted inside the cabinet, provides 10 programmable Form-C relays. (See DN- 7107.) ROME-8: Relay Option Module Enclosure (order ROME-B for black or ROME for red). Provides one N-ANN-RLY Relay Mod- ule already installed. The ROME Series provides mounting space for one additional Relay Module or one addressable Multi- module. (See Installation Sheet PN 53530.) N-ANN-S/PG: Serial/Parallel Printer Gateway module provides a connection for a serial or parallel printer. (See DN-7103.) N-ANN-I/O: LED Driver Module provides connections to a user supplied graphic annunciator. (See DN-7105.) ACM-SR: Relay module provides 8 Form-C 5.0 amp relays. ACM Annunciator Series: LED-type fire annunciators capable of providing up to 99 software zones of annunciation. Available in increments of 16 or 32 points to meet a variety of applications. LDM Graphic Series: Lamp Driver Module series for use with custom graphic annunciators. FDU-80 (Liquid Crystal Display) point annunciator: SO-char- acter, backlit LCD-type fire annunciators capable of displaying English-language text. NOTE: For more information on Compatible Annunciators for use with the FireWarden-100-2 Rev 3, see the following data sheets (document numbers) ACM-BR (DN-3558), ACS/ACM Series (DN- 0524), LDM Series (DN-0551), FDU-80 (DN-6820). COMPATIBLE ADDRESSABLE DEVICES All feature a polling LED and rotary switches for addressing. Nl-100: Addressable low-profile ionization smoke detector. NP-100: Addressable low-profile photoelectric smoke detector. NP-100T: Addressable low-profile photoelectric smoke detector with thermal sensor. NP-1 00R: Addressable remote test capable detector for use with DNR(W) duct smoke detector housings. NH-100: Fast-response, low-profile heat detector. NH-1 00R: Fast-response, low-profile heat detector with rate-of- rise option. NH-100H: Fixed high-temperature detector that activates at 190F/88C. NP-A 100: Addressable low-profile multi-sensor detector. DNR: lnnovair Flex low-flow non-relay duct-detector housing. Order NP-100R separately. DNRW: lnnovair Flex low-flow non-relay duct-detector housing, with NEMA-4 rating. Watertight. (Order NP-100R separately.) NMM-100: Addressable Monitor Module for one zone of nor- mally-open dry-contact initiating devices. Mounts in standard 4.0" (10.16 cm.) box. Includes plastic cover plate and end-of-line resistor. Module may be configured for either a Style B (Class B) or Style D (Class A) I DC. NDM-100: Dual Monitor Module. Same as NMM-100 except it provides two Style B (Class B) only IDCs. NMM-100P: Miniature version of NMM-100. Excludes LED and Style D option. Connects with wire pigtails. May mount in device backbox. NZM-100: Similar to NMM-100, but may monitor up to 20 con- ventional two-wire detectors. Requires resettable 24 VDC power. Consult factory for compatible smoke detectors. NC-100: Addressable Control Module for one Style Y/Z (Class B/A) zone of supervised polarized Notification Appliances. Mounts directly to a 4.0" (10.16 cm.) electrical box. Notification Appliance Circuit option requires external 24 VDC to power noti- fication appliances. NC-100R: Addressable relay module containing two isolated sets of Form-C contacts, which operate as a DPDT switch. Mounts directly to a 4.0" (10.16 cm.) box, surface mount using the SMB500. NOT-BG12LX: Addressable manual pull station with interface module mounted inside. N100-ISO: Fault Isolator Module. This module isolates the SLC loop from short circuit conditions (required for Style 6 or 7 oper- ation). SMB500: Used to mount all modules except the NMM-100P. NMM-100-10: Ten-input monitor module. Mount one or two modules in a BB-XP cabinet (optional). Mount up to six modules on a CHS-6 chassis in a BB-25. NZM-100-6: Six-zone interface module for compatible conven- tional two-wire detectors. Mount one or two modules in a BB-XP cabinet (optional). Mount up to six modules on a CHS-6 chassis in a BB-25. NOTE: For more information on Compatible Addressable Devices for use with the FireWarden-100-2 Rev 3, see the following data sheets (document numbers): N100-ISO (DN-6994), NP-100 series (DN-6995), Nl-100 (DN-6996), NH-100 series (DN-6997), ND-100 series (DN-7006), NP-A 100 (DN-6998), NMM-100/NMM-100PI NDM-100/NZM-100 (DN-6999), NC-100/NC-100R (DN-7000), NOT-BG12LX (DN-7001), NMM-100-10 (DN-6990), and NZM- 100-6 (DN-60150). Wiring Requirements While shielded wire is not required, it is recommended that all SLC wiring be twisted-pair to minimize the effects of electrical interference. Wire size should be no smaller than 18 AWG (0.78 mm2) and no larger than 12 AWG (3.1 mm2). The wire size depends on the length of the SLC circuit. Refer to the panel manual for wiring details. ON-60602:A 1 • 12/07/2010 -Page 3 of 6 •·······r···~~·~:;·~~········· ANN-BUS DEVICES EIA-485 N-ANN-80, N-ANN-LED, in ACS mode N-ANN-S/PG, N-ANN-I/O (two wires) 24 voe 1 1.• .1 1 •········ ANNUNCIATORS ACS/ACM, LDM NOTE: System can use either ANN-BUS devices OR ACS-mode annunciators. They cannot be used simultaneously. ! ! ! ! ! !l ! 8 FORM-C, 5-AMP RELAYS (optional, order ACM-BR) NACs (Notification Appliance Circuits) FireWarden-100-2 Rev 3 Fire Alarm Control/ Communicator Optional REVERSE POLARITY/ CITY BOX OUTPUT (4XTM) 1, \.L.L:LD;;,> SMOKE DETECTORS NP-100, NP-100T, Nl-100, NP-A100 I, I ~? HEAT DETECTORS NH-100, NH-100R, NH-100H DUCT DETECTORS ND-100, ND-100R, DNR BELLS, SIGNALS, STROBES MONITOR/CONTROL NMM-100, NZM-100, NDM-100, N100-ISO, NC-100, NC-100R EIA-485 INTERFACE (four wires) Page 4 of 6 -DN-60602:A 1 • 12/07/2010 EIA-232 INTERFACE (PIM-24) built into the motherboard NOTE: System can use either the printer OR the FDU-80. They cannot be used simultaneously. 24VDC FIRf:4L,ARt,4ANfllUNCIATOU ----------·f "'I I □000 □ FDU-80 Up to 6,000 ft. (1825.8 m) between each FDU-80 in the EIA-485 loop, and between each FDU-80 and the FACP. I I I I I !nn ADORES ABLE MUL Tl-MODULE NZM-100-6, NMM-100-10 MINI-MONITOR NMM-100P I PULL STATION NOT-BG12LX SYSTEM SPECIFICATIONS System Capacity • Intelligent Signalling Line Circuits ......................................... 1 • Addressable device capacity ............................................ 198 • Programmable software zones ........................................... 99 • ACS Annunciators .............................................................. 32 • ANN-bus devices ................................................................ 16 Electrical Specifications AC Power: FireWarden-100-2 Rev 3: 120 VAC, 60 Hz, 3.0 amps. FireWarden-100-2 Rev 3(E): 240 VAC, 5 0 Hz, 1.5 amps. Wire size: minimum 14 AWG (2.00 mm2) with 600 V insulation. Battery charger capacity: 7 AH -18 AH batteries. Up to two 18 Ah batteries can be housed in the FACP cabinet. Larger batter- ies require an external battery charger such as the CHG-75 or CHG-120, and a separate battery cabinet such as the BB-26 or NFS-LBB. Communication Loop: Supervised and power-limited. Notification Appliance Circuits: Each terminal block provides connections for two Style Y (Class B) for a total of four Style Y (Class B) or with an optional ZNAC-92 module converts to four Style Z (Class A) NACs. Maximum signaling current per circuit: 2.5 amps. End-of-Line Resistor: 4.7K ohm, 1/2 watt (P/N 71252 UL listed) for Style Y (Class B) NAC. Refer to panel documenta- tion and Notifier Device Compatibility Document for listed com- patible devices. Two Programmable Relays and One Fixed Trouble Relay: Contact rating: 2.0 amps @ 30 VDC (resistive), 0.5 amps @ 30 VAC (resistive). Form-C relays. Special Application Non-resettable Power (24 voe Nomi- nal): Jumper selectable (JP4) for conversion to resettable power output. Up to 1.0 amp total DC current available from each out- put. Power-limited. Special Application Resettable Power (24 voe nominal): Jumper selectable (JP6) for conversion to non-resettable power. Up to 1.0 amp total DC current available. Refer to the Notifier Device Compatibility Document for listed compatible devices. Remote Sync Output: Remote power supply synchronization output. Nominal special application power: 24 VDC. Maximum current: 300 mA. End-of-Line Resistor: 4.7K ohm. Output linked to NAC 1 control. Supervised and power-limited. Telephone Interface: Unless used with Teldat VISORALARM, requires dedicated business telephone number with a minimum of 5 volts DC (off-hook voltage). Obtain dedicated phone line directly from your local phone company. Do not use shared phone lines or PBX (digital) type phone line extensions. Cabinet Specifications Door: 19.26" (48.92 cm.) high x 16.82" (42.73 cm.) wide x 0.12" (.30 cm.) deep. Backbox: 19.00" (48.26 cm.) high x 16.65" (42.29 cm.) wide x 5.20" (13.34 cm.) deep. Trim Ring (TR-CE- B): 22.00" (55.88 cm.) high x 19.65" (49.91 cm.) wide. Shipping Specifications Weight: 26.9 lbs. (12.20 kg.) Dimensions: 20.00" (50.80 cm.) high x 22.5" (57.15 cm.) wide x 8.5" (21.59 cm.) deep. Temperature and Humidity Ranges This system meets N FPA requirements for operation at O - 49°C/32 -120°F and at a relative humidity 93% ± 2% RH (non- condensing) at 32°C ± 2°c (90°F ± 3°F). However, the useful ·life of the system's standby batteries and the electronic compo- nents may be adversely affected by extreme temperature ranges and humidity. Therefore, it is recommended that this system and its peripherals be installed in an environment with a normal room temperature of 15 -27°C/60 -80°F. NFPA Standards The FireWarden-100-2 Rev 3 complies with the following NFPA 72 Fire Alarm Systems requirements: -LOCAL (Automatic, Manual, Waterflow and Sprinkler Supervisory). -AUXILIARY (Automatic, Manual and Waterflow) (requires 4XTM). -REMOTE STATION (Automatic, Manual, Waterflow and Sprinkler Supervisory) (Where a DACT is not accepted, the alarm, trouble and supervisory relays may be connected to UL 864 listed transmitters. For reverse polarity signaling of alarm and trouble, 4XTM is required.) -PROPRIETARY (Automatic, Manual, Waterflow and Sprin- kler Supervisory). -CENTRAL STATION (Automatic, Manual, Waterflow and Sprinkler Supervisory). -OT, PSON (Other Technologies, Packet-switched Data Net- work) Agency Listings and Approvals The listings and approvals below apply to the basic FireWarden- 100-2 Rev 3 control panel. In some cases, certain modules may not be listed by certain approval agencies, or listing may be in process. Consult factory for latest listing status. • UL Listed: S635 • FM approved • CSFM: 7165-0028:0235 • MEA: 120-06-E, Volume 2 For ULC-listed version, see DN-60600. NOTIFIER® is a registered trademark of Honeywell International Inc. Wheelock® is a registered trademark of and Exceder™ is a trademark of Cooper Notification. ©201 O by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited. ISO 9001 This document is not intended to be used for installation purposes. lfl =I; ii I =I I =I •J ENGINEERING & MANUFACTURING QUALITY SYSTEMS We try to keep our product information up-to-date and accurate. · We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118. www.notifier.com Page 6 of 6 -DN-60602:A1 • 12/07/2010 Made in the U.S. A. LISTING No. CATEGORY: LISTEE: DESIGN: RATING: INSTALLATION: MARKING: APPROVAL: NOTE: XLF: CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING -BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE 7165-0028:0235 7165 --FIRE ALARM CONTROL UNIT (COMMERCIAL) NotifierOne Fire-Lite Place, Northford, CT 06472-1653 Contact: Vladimir Kireyev (203) 484-6277 Fax (203) 484-7309 Email: vladimir.kireyev@honeywell.com Page 1 of 1 Models Fire Warden 100 and *Fire Warden 100-2 addressable control units. Local, auxiliary, remote station, central station and proprietary (protected premise). This panel also can be used with NFV-25/50ZST (Fire Voice-25/-50ZST) Zoned System Voice with Telephone for Emergency Voice evacuation Applications. Refer to listee's data sheet for detailed product description, operational considerations and required/optional accessories. When required, accessories shall be CSFM listed. 120 VAC , 60 Hz, 2.06 A Primary, 24 voe Secondary In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. Listee's name, model number, electrical rating, and UL label. Listed as an addressable fire alarm control panel for use with separately listed compatible initiating and indicating devices. Refer to listee's Installation Instruction Manual for details. This control unit can generate a distinctive three-pulse Temporal Pattern Fire Alarm Evacuafion Signal (for total evacuation) in accordance with NFPA 72, 2002 Edition. This control unit meets the requirements of UL Standard 864, 9th Edition. For Fire Alarm Verification Feature (delay of fire alarm signal), the maximum Retard/Reset/Restart period shall not exceed 30 seconds. 7165-0075:0208 *Rev. 08-17-09 fm This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: Authorized By: July 01, 2012 JASON DEWITT, Deputy State Fire Marshal Fire Engineering Division Listing Expires June 30, 2013 N-ANN-80 SO-Character LCD Serial Annunciator General The N-ANN-80 annunciator is a compact, backlit, SO-character LCD fire annunciator that mimics the Fire Alarm Control Panel (FACP) display. It provides system status indicators for AC Power, Alarm, Trouble, Supervisory, and Alarm Silenced condi- tions. The N-ANN-80 and the FACP communicate over a two- wire serial interface employing the ANN-BUS communication format. Connected devices are powered, via two additional wires, by either the host FACP or a remote UL-listed, filtered power supply. N-ANN-80 is black; for white order N-ANN-80-W. The N-ANN-80 displays English-language text of system point information including device type, zone, independent point alarm, trouble or supervisory status, as well as any custom alpha labels programmed into the control panel. It includes con- trol switches for remote control of critical system functions. (A keyswitch prevents unauthorized operation of the control switches.) Up to eight N-ANN-80s may be connected to the ANN-BUS of each FACP. Minimal programming is required, which saves time during system commissioning. The N-ANN-80 is compatible with NOTIFIER FACPs with an ANN-BUS, such as the NFW-50. Features • Listed to UL Standard 864, 9th Edition. • Backlit BO-character LCD display (20 characters x 4 lines). • Mimics all display information from the host panel. • Control switches for System Acknowledge, Signal Silence, Drill, and Reset. • Control switches can be independently enabled or disabled at the FACP. • Keyswitch enables/disables control switches and mechani- cally locks annunciator enclosure • Keyswitch can be enabled or disabled at the FACP. • Enclosure supervised for tamper. • System status LEDs for AC Power, Alarm, Trouble, Supervi- sory, and Alarm Silence. • Local sounder can be enabled or disabled at the FACP. • N-ANN-80 connects to the ANN-BUS terminal on the FACP and requires minimal panel programming. • Displays device type identifiers, individual point alarm, trou- ble, supervisory, zone, and custom alpha labels. • Time-and date display field. • Surface mount directly to wall or to single, double, or 4" square electrical box. • Semi-flush mount to single, double, or 4" square electrical box. Use ANN-SB80KIT for angled view mounting. • Can be remotely located up to 6,000 feet (1,800 m) from the panel. • Backlight turns off during AC loss to conserve battery power but will turn back on if an alarm condition occurs. • May be powered by 24 voe from the host FACP or by remote power supply (requires 24 VDC). • Up to eight N-ANN-80s can be connected on the ANN-BUS. Controls and Indicators AC Power • Alarm dn-7114:c • A 1-65 ({;))NOTIFIER® by Honeywell • Trouble • Supervisory • Alarm Silenced Specifications • Operating voltage range: 18 VDC to 28 VDC. • Current consumption @ 24 voe nominal (filtered and non- resettable): 40 mA maximum. • Ambient temperature: 32°F to 120°F (0°C to 49°C). • Relative humidity: 93% ± 2% RH (noncondensing) at 32°C ± 2°C (90°F ± 3°F). • 5.375" (13.65 cm.) high x 6.875" (17.46 cm.) wide x 1.375" (3.49 cm.) deep. • For use indoors in a dry location. • All connections are power-limited and supervised. Agency Listings and Approvals The listings and approvals below apply to the N-ANN-80. In some cases, certain modules may not be listed by certain approval agencies, or listing may be in process. Consult factory for latest listing status. • UL: S635 • FM approved • CSFM: 7120-0028:240 • MEA: 442-06-E Vol. 2 The ANN-BUS POWERING THE DEVICES ON THE= ANN-BUS FROM AUXILIARY POWER SUPPLY The ANN-BUS can be powered by an auxiliary power supply when the maximum number of ANN-BUS devices exceeds the ANN-BUS power requirements. See the FACP manual for more information. dn-7114:c • 5/22/09-Page 1 of 2 ANN-BUS DEVICE ADDRESSING Each ANN-BUS device requires a unique address (ID Number) in order to communicate with the FACP A maximum of 8 devices can be connected to the FACP ANN-BUS communication circuit. See the FACP manual for more information. WIRE REQUIREMENTS: COMMUNICATIONS CIRCUIT The N-ANN-80 connects to the FACP ANN-BUS communica- tions circuit. To determine the type of wire and the maximum wir- ing distance that can be used with FACP ANN-BUS accessory modules, it is necessary to calculate the total worst case current draw for all modules on a single 4-conductor bus. The total worst case current draw is calculated by adding the individual worst case currents for each module. NOTE: For total worst case current draw on a single ANN-BUS refer to appropriate FACP manual. After calculating the total worst case current draw, the following table specifies the maximum distance the modules can be located from the FACP on a single wire run. The table ensures 6.0 volts of line drop maximum. In general, the wire length is lim- ited by resistance, but for heavier wire gauges, capacitance is the limiting factor. These cases are marked in the chart with an asterisk (*). Maxi- mum length can never be more than 6,000 feet (1 ,800 m), regardless of gauge used. See table below. WIRE REQUIREMENTS: POWER CIRCUIT • 14 to 18 AWG (0.75 -2.08 mm2) wire for 24 voe power cir- cuit is acceptable. • All connections are power-limited and supervised. • A maximum of eight N-ANN-80 modules may be connected to this circuit. Communication Pair Wiring Distance: FACP to Last ANN-BUS Module Total Worst Case 22 Gauge Current Draw (amps) 0.100 1,852 ft. 0.200 926 ft. 0.300 617 ft. 0.400 463 ft. 0.500 370 ft. 0.600 309 ft. 0.700 265 ft. 0.800 231 ft. 0.900 206 ft. 1.000 (max.) 185 ft. WIRING CONFIGURATION The following figure illustrates the wiring between the FACP and ANN-BUS devices. mm ANN-BUS Device ANN-BUS and power wiring are supervised and power-limited. 0 12345678 FACP Wiring to ANN-BUS Device 18 Gauge 16 Gauge 14 Gauge 4,688 ft. * 6,000 ft. *6,000 ft. 2,344 ft. 3,731 ft. 5,906 ft. 1,563 ft. 2,488 ft. 3,937 ft. 1,172 ft. 1,866 ft. 2,953 ft. 938 ft. 1,493 ft. 2,362 ft. 781 ft. 1,244 ft. 1,969 ft. 670 ft. 1,066 ft. 1,687 ft. 586 ft. 933 ft. 1,476 ft. 521 ft. 829 ft. 1,312 ft. 469 ft. 746 ft. 1,181 ft. ORDERING OPTIONS: N-ANN-80: Black 80 character LCD Annunciator. N-ANN-80-W: White, 80 character LCD Annunciator. ANN-SBSOKIT-B: Black surface mount backbox with angled wedge. ANN-SBSOKIT-W: White surface mount backbox with angled wedge. ©2009 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited. ISO 9001 This document is not intended to be used for installation purposes. 1➔=1-0•#i ■#i·) ENGINEERIN~ & MANUFACTIIRING QUALITY SYSTEMS Page 2 of 2 -dn-7114:c • 5/22/09 We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118. www.notifier.com Made in the U.S. A. • LISTING No. CATEGORY: LISTEE: DESIGN: INSTALLATION: MARKING: APPROVAL: XLF: CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING -BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE 7120-0028: 0240 Page 1 of 1 7120 --ANNUNCIATORS NotifierOne Fire-Lite Place, Northford, CT 06472-1653 Contact: Vladimir Kireyev (203) 484-6277 Fax (203) 484-7309 Email: vladimir.kireyev@honeywell.com Model N-ANN-80 rem ote fire annunciator. Unit is a BO-character, supervised backlit LCD fire annunciator. Communication between the control panel and the annunciator is accomplished over a two-wire serial interface employing the ANN-BUS protocol. Refer to listee's data sheet for additional detailed product description and operational considerations. In accordance with listee's printed installation instructions, applicable codes & ordinances and in manner acceptable to the authority having jurisdiction. Listee's name, product number, electrical rating and UL label. Listed as an annunciator for use separately listed compatible fire alarm control units. Refer to manufacturer's installation manual for details . 7120-0075:0211 10-03-06 jw This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: Authorized By : July 01, 2012 JASON DEWITT, Deputy State Fire Marshal Fire Engineering Division Listing Expires June 30, 2013 NP-1 OO (A)-Series Addressable Photoelectric Detectors for the FireWarden Series The NP-1 OO(A), NP-1 OOT(A) and NP-1 OOR(A} addressable, low-profile plug-in photoelectric detectors use a state-of-the- art photoelectric sensing chamber with communications to provide open area protection and are used exclusively with NOTIFIER's FireWarden Series (FireWarden-100-2 and Fire- Warden-50) and Spartan (NSP-25) Addressable Fire Alarm Control Panels (FACPs). The NP-1 OOT(A) adds thermal sen- sors that will alarm at a fixed temperature of 135°F (57°C). Since these detectors are addressable, they will help emer- gency personnel qu ickly locate a fi re during its early stages, potentially saving precious rescue time while also reducing property damage. Two LEDs on each sensor light to provide a local, visible sensor indication. Remote LED annunciator capa- bility is available as an optional accessory, PN RA 1 00Z(A). The NP-1 OOR(A) is a re mote test capable detector for use with DNR(A)/DNRW duct smoke detector housings. Features SLCloop • Two-wire loop connection. • Unit uses base for wi ring. Addressing • Addressable by device. • Rotary, decimal addressing: 01 -99 with FireWarden-100-2 and NSP-25, and 01 -50 with FireWarden -50. Architecture • Unique single-source, dual-chamber design to respond quickly and dependably to a broad range of fires. • Sleek, low-profile design. • Integral communications and built-in type identification. • Built-in tamper-resistant fe ature. • Removable cover and insect-resistant screen for simple field cleaning. Operation • Withstands air velocities up to 4,000 feet-per-minute (20 ml sec.) without triggeri ng a false alarm. • Factory preset at 1.5% nominal sensitivity for panel alarm threshold level. • Visible LE D "blinks" wh en the unit is addressed (communi- cating with the fire panel) and latches on in alarm. Mechanicals • Sealed against back pressure. • Direct surface mounting or electrical box mounting. • Mounts to: single-gang box, 3.5" (8.89 cm) or 4.0" (10.16 cm) octagonal box, or 4.0" (10.16 cm) square electrical box (using a plaster ring -included). Other system features • Fully coated circuit boards and superior RF/transient pro- tection. • 94-V0 plastic flammability rating. • Low standby current. Options • Remote LED output connection, PN RA 1 00Z(A). DN-6995:C • A 1-320 ~NOTIFIE R @ by Honeywe ll NP-1 OO(A) in 821 OLP(A) Base Applications Use photoelectric detectors in life-safety applications to pro- vide a broad range of fire-sensing capability, especially where smoldering fires are anticipated. Ionization detectors are often better than photoelectric detectors at sensing fast, flaming fires. Construction These detectors are constructed of off-white fire resistant plas- tic. NP-100(A) series plug-in, low-profile smoke detectors are designed to commercial standards and offer an attractive appearance. Installa tion NP-100(A) series plug-in detectors use a detachable mounting base to simplify installation, service and maintenance. Mount base (all base types) on an electrical backbox which is at least 1.5" (3.81 cm) deep. For a chart of compatible junction boxes, see DN-60054. NOTE: Because of the inherent supervision provided by the SLC loop, end-of-line resistors are not required. Wiring "T-taps" or branches are permitted for Style 4 (Class B) wiring. NP-1 00R(A) mounts in a DNR(A)IDNRW duct detector housing. Operation Each NP-100(A) series detector uses one of 99 possible addresses on the FireWarden-100-2 and NSP-25, or one of 50 possible addresses on the FireWarden-50 Signaling Line Cir- cuit (SLC). It responds to regular polls from the system and reports its type and status. The addressable photoelectric sensor in the NP-1 00(A) series has a unique unipolar chamberthat responds quickly and uni- formly to a broad range of smoke conditions. It can withstand wind gusts up to 4,000 feet-per-minute (20 m/sec.) without sending an alarm level signal. Because of its unipolar cham- ber, the NP-100(A) series is approximately two times more responsive than most photoelectric sensors. This makes it a more stable detector. DN-6995:C • 12/07/2011 -Page 1 of 2 Detector Sensitivity Test Each detector can have its sensitivity tested (required per NFPA 72, Chapter 14 on Inspection, Testing and Maintenance) when installed/connected to a FireWarden-100-2 or FireWar- den-50 addressable fire alarm control panel. The results of the sensitivity test can be printed off the FireWarden-100-2 or Fire- Warden-50 for record keeping. Specification Voltage range: 15 -32 voe (peak). Standby current: 300 µA @ 24 voe. LED current: 6.5 mA @ 24 voe (latched "ON"). Air velocity: 4,000 ft./min. (20 m/sec.) maximum. Size: 2.1" (5.33 cm) high; base determines diameter. -821 0LP(A): 6.1" (15.5 cm) diameter. -8501 (A): 4.1" (10.4 cm) diameter. -8200SR(A): 6.875" (17.46 cm) diameter. -B224RB(A): 6.2" (15.748 cm) diameter. Weight: 3.6 oz. (102 g). Operating temperature range: for NP-100(A): 0°c to 49°C (32°F to 120°F); for NP-100T(A): 0°C to 38°C (32°F to 100°F). NP-100R(A): installed in a DNR(A)/DNRW -20°C to 70°C (-4°F to 158°F). Temperature: 0°c -49°C (32°F -120°F). Relative humidity: 10% -93%, non-condensing. Listings Listings and approvals below apply to the NP-1 00(A), NP- 1 00T(A), and NP-1 00R(A) detectors. In some cases, certain modules may not be listed by certain approval agencies, or listing may be in process. Consult factory for latest listing sta- tus. • UL Listed: S1115. • ULC Listed: S911 . • CSFM: 7272-0028:0231. • MEA: 243-02-E Vol. 2. • Maryland State Fire Marshal: permit 2173. • FM approved. Product Line Information NOTE: '~" suffix indicates ULC Listed model. NP-100: Adressable photoelectric detector; B21 OLP base included. NP-100A: Sames as NP-100 with ULC Listing; B210LPA base included. NP-100T: Same as NP-100 but with thermal element; B21 OLP base included. NP-100TA: Same as NP-100T with ULC Listing; B210LPA base included. NP-100R: Remote test capable addressable photoelectric detector for use with a DNRA/DNRW duct detector housing; 821 OLP base included. NP-100RA: Same as NP-100R with ULC Listing for use with a DNRA duct detector housing; B21 0LPA base included. INTELLIGENT BASES NOTE:'~" suffix indicates ULC Listed model. NOTE: For details about intelligent bases and their mounting, see ON-60054. 821 0LP(A): Plug-in detector base (included); standard U.S. flanged low-profile mounting base. 8210LPBP: Bulk pack of 821 OLP; package contains 1 0. 8501 (A): Standard European flangeless mounting base. 8501 BP: Bulk pack of 8501; package contains 10. 8200SR(A): Intelligent sounder base capable of producing sound output with ANSI Temporal 3 or continuous tone. Replaces 8501 BH series bases in retrofit applications. B224RB(A): Plug-in System Sensor relay base. Screw termi- nals: up to 14 AWG (2.0 mm2). Relay type: Form-C. Rating: 2.0 A @ 30 voe resistive; 0.3 A @ 11 o voe inductive; 1.0 A @ 30 voe inductive. 8224Bl(A): Plug-in System Sensor isolator detector base. Maximum 25 devices between isolator bases (see ON-6994). ACCESSORIES F110: Retrofit flange to convert B21 0LP(A) to match the B71 0LP(A) profile, or to convert older high-profile bases to low-profile. F11 0BP: Bulk pack of F11 0; package contains 15. F210: Replacement flange for B21 0LP(A) base. RA 1 00Z(A): Remote LED annunciator. 3 -32 voe. Mounts to a U.S. single-gang electrical box. For use with B501 (A) and 821 0LP(A) bases only. SMBG00: Surface mounting kit M02-04-00:Test magnet. M02-09-00: Test magnet with telescoping handle. XR2B: Detector removal tool. Allows installation and/or removal of detector heads from bases in high ceiling applica- tions. XP-4: Extension pole for XR28. Comes in three 5-foot (1.524 m) sections. TSS-127-010: Detector removal tool without pole. BCK-2008: Black detector covers for use with NP-1 00(A) only; box of 10. WCK-2008: White detector covers for use with NP-1 00(A) only; box of 10. NOTIFIER® and FireWarden® are registered trademarks of Honeywell International Inc. ©2011. All rights reseNed. Unauthorized use of this document is strictly prohibited. ISO 9001 This document is not intended to be used for installation purposes. 14 =i ;0 I #0 =I •J ENGINEERING & MANUFACTURING QUALITY SYSTEMS We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118. www.notifier.com Page 2 of 2 -DN-6995:C • 12/07/2011 Made in the U.S. A. LISTING No. CATEGORY: LISTEE: DESIGN: RATING: INSTALLATION: MARKING: APPROVAL: NOTE: XLF: CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING -BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE 7272-0028:0231 7272 --SMOKE DETECTOR-SYSTEM TYPE-PHOTOELECTRIC NotifierOne Fire-Lite Place, Northford, CT 06472-1653 Contact: Vladimir Kireyev (203) 484-6277 Fax (203) 484-7309 Email: vladimir.kireyev@honeywell.com Page 1 of 1 Models NP-100, NP-100R* and NP-100T photoelectric type smoke detectors. Model NP-1 00T has a 135°F supplement integral heat sensor which only assists in a fire situation. The purpose of this thermal circuitry is to increase the sensitivity of the detector. This thermal circuitry is NOT approved for use as a heat detector. Refer to listee's printed data sheet for additional detailed product description and operational considerations. 24VDC In accordance with listee's printed installation instructions, applicable codes & ordinances and a manner acceptable to the authority having jurisdiction. Listee's name, model number, electrical rating and UL label. Listed as photoelectric smoke detector for use with separately listed compatible fire alarm control units and bases. All models are suitable for open areas and inside duct installations with air velocities between 0 -4000 FPM. *Models NP-100 and NP-1 00R are also approved for installations inside Notifier duct detector housing ND-200 (OSFM Listing No. 3242-0028:236) and System Sensor duct detector housing DNRW (OSFM Listing No. 3242-1653:210). Refer to listee's Installation Instruction Manual for details. The photoelectric type detectors are generally more effective at detecting slow, smoldering fires, which smolder for hours before bursting into flames. Sources of these fires may include cigarettes burning in couches or bedding. The ionization type detectors are generally more effective at detecting fast, flaming fires, which consume combustible materials rapidly and spread quickly. Sources of these fires may include paper burning in a waste container or a grease fire in the kitchen. 7272-0075:0194 *Rev. 01-27-10 fm This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: Authorized By: July 01, 2012 JASON DEWITT, Deputy State Fire Marshal Fire Engineering Division Listing Expires June 30, 2013 • .. NOT-BG12LX Addressable Manual Pull Station General The Notifier NOT-BG 12LX is a state-of-the-art, dual-action (i.e., requires two motions to activate the station) pull station that includes an addressable interface fo r FireWarden series intelligent control panels, and the NSP-25 panel. Because the NOT-BG 12LX is addressable, the control panel can display the exact location of the activated manual station. This leads fire personnel quickly to the location of the alarm. Features • Maintenance personnel can open station for inspection and address setting without causing an alarm condition. • Built-in bicolor LED, which is visible through the handle of the station, flashes in normal operation and latches steady red when in alarm. • Handle latches in down position and the word "ACTIVATED" appears to clearly indicate the station has been operated. • Captive screw terminals wire-ready for easy connection to SLC loop (accepts up to 12 AWG/3.25 mm2 wi re). • Can be surface mounted (with SB-10 or SB-I/O) or semi- flush mounted. Semi-flush mount to a standard single- gang, double-gang, or 4" (10.16 cm) square electrical box. • Smooth dual-action design. • Meets ADAAG controls and operating mechanisms guide- lines (Section 4.1.3[13]); meets ADA requirement for 5 lb. maximum activation force. • Highly visible. • Attractive shape and textured finish. • Key reset. • Includes Braille text on station handle. • Optional trim ring (BG 12TR). • Meets UL 38, Standard for Manually Actuated Signaling Boxes. Construction Shell , door, and handle are molded of durable polycarbonate material with a textured finish . Specifications • Shipping Weight: 9.6 oz. (272.15 g) • Normal operating voltage: 24 voe. • Maximum SLC loop voltage: 28.0 voe. • Maximum SLC standby current: 375 µA. • Maximum SLC alarm current: 5 mA. • Temperature Range: 32°F to 120°F (0°C to 49°C) • Relative Humidity: 10% to 93% (noncondensing) • For use indoors in a dry location Installat ion The NOT-BG 12LX will mount semi-flush into a single-gang, double-gang, or standard 4" (10.16 cm) square electrical outlet box, or will surface mount to the model SB-10 or SB-I/O sur- face backbox. If the NOT-BG 12LX is being semi-flush mounted, then the optional trim ring (BG 12TR) may be used. DN-7001:D • A1-380 @}) NOTI Fl ER@ by Honeywell The NOT-BG12LX Addressable Manual Pull Station The BG 12TR is usually needed for semi-flush mounting with 4" (10.16 cm) or double-gang boxes (not with single-gang boxes). Operation Pushing in, then pulling down on the handle causes it to latch in the down/activated position. Once latched, the word "ACTI- VATED" (in bright yellow) appears at the top of the handle, while a portion of the handle protrudes from the bottom of the station. To reset the station, simply unlock the station with the key and pull the door open. This action resets the handle; clos- ing the door automatically resets the switch. Each manual station, on command from the control panel, sends data to the panel representing the state of the manual switch. Two rotary decimal switches allow address settings (1 -99 on NFW2-100/NFW2-100C, 1 -50 for NFW-50/NFW- 50C). Architectural/Engineering Specifications Manual Fire Alarm Stations shall be non-coded, with a key- operated reset lock in order that they may be tested, and so designed that after actual Emergency Operation, they cannot be restored to normal except by use of a key. An operated sta- tion shall automatically condition itself so as to be visually detected as activated. Manual stations shall be constructed of red-colored polycarbonate material with clearly visible operat- ing instructions provided on the cover. The word FIRE shall appear on the front of the stations in white letters, 1.00 inches (2.54 cm) or larger. Stations shall be suitable for surface mounting on matching backbox SB-10 or SB-I/O; or semi-flush mounting on a standard single-gang, double-gang, or 4" (10.16 cm) square electrical box, and shall be installed DN-700'1 :D • 4/13/20'12 -Page 1 of 2 within the limits defined by the Americans with Disabilities Act (ADA) or per national/local requirements. Manual Stations shall be Underwriters Laboratories listed. Manual stations shall connect with two wires to one of the con- trol panel SLC loops. The manual station shall, on command from the control panel, send data to the panel representing the state of the manual switch. Manual stations shall provide address setting by use of rotary decimal switches. Product Line Information NOT-BG12LX: Dual-action addressable pull station. Includes key locking feature. (Listed for Canadian and non-Canadian applications.) SB-10: Surface backbox; metal. SB-1/O: Surface backbox; plastic. BG12TR: Optional trim ring . 17021: Keys, set of two. Agency Listings and Approvals In some cases, certain modules or applications may not be listed by certain approval agencies, or listing may be in pro- cess. Consult factory for latest listing status. • UL/ULC Listed: S692 (listed for Canadian and non-Cana- dian applications). • MEA: 67-02-E Vol. IV. • CSFM: 7150-0028:0199. • FM Approved. Patented: U.S. Patent No. D428,351; 6,380,846; 6,314,772; 6,632,108. NOTIFIER® is a registered trademark of Honeywell International Inc. ISO 9001 l➔=l;iil=il=l·i ENGINEERING & MANUFACTURING QUALITY SYSTEMS ©2012 by Honeywell International Inc. All rights reseNed. Unauthorized use of this document is strictly prohibited. This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. Made in the U.S. A. For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118. Page 2 of 2 -DN-7001 :D • 4/13/2012 www.notifier.com -a.~'114•·•~-•-~~g,:~~.-:Z~IIRSrm:;J~!'.=itl!IIM:,-.:~~'IJLU' LISTING No. CATEGORY:· LISTEE: DESIGN: INSTALLATION: MARKING: APPROVAL: CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING -BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE 7150-0028:0199 7150 --FIRE ALARM PULL BOXES NotifierOne Fire-Lite Place, Northford, CT 06472-1653 Contact: Vladimir Kireyev (203) 484-6277 Fax (203) 484-7309 Email: vladimir.kireyev@honeywell.com Page 1 of 1 Models NBG-12, NBG-12S, NBG-12LR, NBG-12LRA, NBG-12LAO, NBG-12LAOB, NBG-12-LO, NBG-12LOB, NBG-12W, NBG-12LW, NBG-12NC, NBG-12WP, NBG-12LWP, NBG-12L, NBG-12LX, NBG-12LA, NBG-12PS, NBG-12LSP, NBG-12LPS, NBG-12LPSP, NBG-12SP, NOT-BG12LX, NBG-12LXSP, NBG-12LXBL* and NBG-12LXP* fire alarm pull boxes. All units except Model NBG-12S are dual action pull stations. Models NBG-12LR and NBG-12LRA are intended for agent releasing device. Refer to listee's data sheet for detailed product description and operational considerations. In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. Listee's name, model number, rating , and UL label. Listed as fire alarm pull boxes for use with separately listed compatible fire alarm control units. Models NBG-12WP, NBG-12LW, NBG-12W, NBG-12LWP, NBG-12LAO, NBG-12LO, NBG-12LAOB and NBG-12LOB are intended for outdoor use when installed with Models WBB , SB-I/O, or WP-10 back box. Refer to listee's Installation Instruction Manual for details. *These manual pull boxes meet the requirements of UL Standard 38, 1999 Edition and California amendments which the controls and operating mechanisms required to be operable at no more than 5Ibs. force with one hand and shall not require tight grasping, pinching, or twisting of the wrist. *Rev. 04-08-10 bh This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: Authorized By: July 01, 2012 JASON DEWITT, Deputy State Fire Marshal Fire Engineering Division Listing Expires June 30, 2013 Monitor M o dules NMM-1 00(A), NMM-1 00P(A), NZM-1 00(A), and NDM-1 00(A) for FireWarden Series Panels General Four different monitor modules are available for Notifier's Fire- Warden Series intelligent control panels for a variety of appli- cations. Monitor modules supervise a circuit of dry-contact input devices, such as conventional heat detectors and pull stations, or monitor and power a circuit of two-wire smoke detectors (NZM-1 00(A)). NMM-1 00(A) is a standard-sized module (typically mounts to a 4" [10.16 cm] square box) that supervises either a Style D (Class A) or Style B (Class B) circuit of dry-contact input devices. NMM-1 00P(A) is a miniature monitor module a mere 1.3" (3.302 cm) H x 2.75" (6.985 cm) W x 0.5'' (1.270 cm) D that supervises a Style B (Class B) circuit of dry-contact input devices. Its compact design allows the NMM-1 00P(A) to be mounted in a single-gang box behind the device it monitors. NZM-100(A) is a standard-sized module that monitors and supervises compatible two-wire, 24 volt, smoke detectors on a Style D (Class A) or Style B (Class B) circuit. NDM-100(A) is a standard-sized dual monitor module that monitors and supervises two independent two-wire Style B (Class B) dry-contact initiating device ci rcuits (IDCs) at two separate, consecutive addresses in intelligent, two-wire systems. NMM-100(A) Monitor Module • Built-in type identification automatically identifies this device as a monitor module to the control panel. • Powered directly by two-wire SLC loop. No additional power required. • High noise (EMF/RFI) immunity. • SEMS screws with clamping plates for ease of wiring. • Direct Decade entry of address: 01 -99 on FireWarden- 100-2, 01 -50 on FireWarden-50. • LED flashes during normal operation and latches on steady to indicate alarm. The NMM-1 00(A) Monitor Module is intended for use in intelli- gent, two-wire systems, where the individual address of each module is selected using the built-in rotary switches. It pro- vides either a two-wire or four-wire fault-tolerant Initiating Device Circuit (IDC) for normally-open-contact fire alarm and supervisory devices. The module has a panel-controlled LED indicator. NMM-100(A) APPLICATIONS Use to monitor a zone of four-wire smoke detectors, manual fire alarm pull stations, waterflow devices, or other normally- open dry-contact alarm activation devices. May also be used to monitor normally-open supervisory devices with special supervisory indication at the control panel. Monitored circuit may be wired as an NFPA Style B (Class B) or Style D (Class A) Initiating Device Circuit. A 47K ohm End-of-Line Resistor (provided) terminates the Style B circuit. No resistor is required for supervision of the Style D circuit. DN-6999:C @})NOTIFIER® by Honeywell NMM-100(A) (Type H) NMM-1 00(A) OPERATION Each NMM-1 00(A) uses one of the available module addresses on an SLC loop. It responds to regular polls from the control panel and reports its type and the status (open/nor- mal/short) of its Initiating Device Circuit (IDC). A flashing LED indicates that the module is in communication with the control panel. The LED latches steady on alarm (subject to current limitations on the loop). NMM-100(A) SPECIFICATIONS Nominal operating voltage: 15 to 32 voe. Maximum current draw: 5.0 mA (LED on). Average operating current: 350 µA (LED flashing), 1 com- munication every 5 seconds, 47k EOL. Maximum IDC wiring resistance: 40 ohms. EOL resistance: 47K ohms. Temperature range: 32°F to 120°F (0°C to 49°C). Humidity range: 10% to 93% noncondensing. Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x 1.25" (3.175 cm) deep. Mounts to a 4" (10.16 cm) square x 2.125" (5.398 cm) deep box. DN-6999:C • 10/06/2010 -Page 1 of 4 NMM-1 00P(A) Mini Monitor Module • Built-in type identification automatically identifies this device as a monitor module to the panel. • Powered directly by two-wire SLC loop. No additional power required. • High noise (EMF/RFI) immunity. • Tinned, stripped leads for ease of wiring. • Direct Decade entry of address: 01 -99 on FireWarden- 100-2, 01 -50 on FireWarden-50. sl 1--~ 0 1 lJ.J a <..) -J ' -J lJ.J ~ -J i 0 a:: -J ~i s en ! I The NMM-1 00P(A) Mini Monitor Module can be installed in a single-gang junction directly behind the monitored unit. Its small size and light weight allow it to be installed without rigid mounting. The NMM-1 00P(A) is intended for use in intelligent, two-wire systems where the individual address of each module is selected using rotary switches. It provides a two-wire initiat- ing device circuit for normally-open-contact fire alarm and security devices. NMM-1 00P(A) NMM-1 DDP(A) APPL/CATIONS Use to monitor a single device or a zone of four-wire smoke detectors, manual fire alarm pull stations, waterflow devices, or other normally-open dry-contact devices. May also be used to monitor normally-open supervisory devices with special super- visory indication at the control panel. Monitored circuit/device is wired as an NFPA Style B (Class B) Initiating Device Circuit. A 47K ohm End-of-Line Resistor (provided) terminates the cir- cuit. NMM-1DDP(A) OPERATION Each NMM-1 00P(A) uses one of the available module addresses on an SLC loop. It responds to regular polls from the control panel and reports its type and the status (open/nor- mal/short) of its Initiating Device Circuit (IDC). NMM-1 DDP(A) SPECIF/CATIONS Nominal operating voltage: 15 to 32 VDC. Average operating current: 350 µA, 1 communication every 5 seconds, 47k EOL; 600 µA Max. (Communicating, IDC Shorted). Maximum IDC wiring resistance: 40 ohms. Maximum IDC Voltage: 11 Volts. Maximum IDC Current: 400 µA. EOL resistance: 47K ohms. Temperature range: 32°F to 120°F (0°C to 49°C). Humidity range: 10% to 93% noncondensing. Page 2 of 4 -DN-6999:C • 10/06/2010 Dimensions: 1.3" (3.302 cm) high x 2.75" (6.985 cm) wide x 0.65" (1.651 cm) deep. Wire length: 6" (15.24 cm) minimum. NZM-1 00(A) Interface Module • Supports compatible two-wire smoke detectors. SupeNises IDC wiring and connection of external power source. • High noise (EMF/RFI) immunity. • SEMS screws with clamping plates for ease of wiring. • Direct Decade entry of address:, 01 -99 on FireWarden- 100-2, 01 -50 on FireWarden-50. • LED flashes during normal operation. • LED latches steady to indicate alarm on command from control panel. The NZM-1 00(A) Interface Module is intended for use in intelli- gent, addressable systems, where the individual address of each module is selected using built-in rotary switches. This module allows intelligent panels to interface and monitor two- wire conventional smoke detectors. It transmits the status (nor- mal, open, or alarm) of one full zone of conventional detectors back to the control panel. All two-wire detectors being moni- tored must be UL compatible with the module. NZM-100(A) APPL/CATIONS Use the NZM-100(A) to monitor a zone of two-wire smoke detectors. The monitored circuit may be wired as an NFPA Style B (Class B) or Style D (Class A) Initiating Device Circuit. A 3.9 K ohm End-of-Line Resistor (provided) terminates the end of the Style B or D (class B or A) circuit (maximum IDC loop resistance is 25 ohms). Install ELR across terminals 8 and 9 for Style D application. NZM-100(A) OPERATION Each NZM-1 00(A) uses one of the available module addresses on an SLC loop. It responds to regular polls from the control panel and reports its type and the status (open/nor- mal/short) of its Initiating Device Circuit (IDC). A flashing LED indicates that the module is in communication with the control panel. The LED latches steady on alarm (subject to current limitations on the loop). · NZM-100( A) SPECIF/CATIONS Nominal operating voltage: 15 to 32 voe. Maximum current draw: 5.1 mA (LED on). Maximum IDC wiring resistance: 25 ohms. Average operating current: 300 µA, 1 communication and 1 LED flash every 5 seconds, 3.9k eol. EOL resistance: 3.9K ohms. External supply voltage (between Terminals T3 and T4): DC voltage: 24 volts power limited. Ripple voltage: 0.1 Vrms maximum. Current: 90 mA per module maximum. Temperature range: 32°F to 120°F (0°C to 49°C). Humidity range: 10% to 93% noncondensing. Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x 1.25" (3.175 cm) deep. Mounts to a 4" (10.16 cm) square x 2.125" (5.398 cm) deep box. NDM-1 00(A) Dual Monitor Module The NDM-1 00(A) Dual Monitor Module is intended for use in intelligent, two-wire systems. It provides two independent two- wire initiating device circuits (IDCs) at two separate, consecutive addresses. It is capable of monitoring normally open contact fire alarm and supervisory devices. The module has a single panel- controlled LED. NOTE: The NDM-1 OO(A) provides two Style B (Class B) /DC cir- cuits ONLY Style D (Class A) /DC circuits are NOT supported in any application. NDM-100(A) SPECIFICATIONS Normal operating voltage range: 15 to 32 voe. Maximum current draw: 6.4 mA (LED on). Average operating current: 750 µA (LED flashing). Maximum IDC wiring resistance: 1,500 ohms. Maximum IDC Voltage: 11 Volts. Maximum IDC Current: 240 µA EOL resistance: 47K ohms. Maximum SLC Wiring resistance: 40 Ohms. Temperature range: 32° to 120°F (0° to 49°C). Humidity range: 10% to 93% (non-condensing). Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x 2.125" (5.398 cm) deep. NDM-100(A) AUTOMATIC ADDRESSING The NDM-1 00(A) automatically assigns itself to two address- able points, starting with the original address. For example, if the NDM-100(A) is set to address "26", then it will automati- cally assign itself to addresses "26" and "27". NOTE: "Ones" addresses on the NDM-100(A) are 0, 2, 4, 6, or 8 only. Terminals 6 and 7 use the first address, and terminals 8 and 9 use the second address. A_ CAUTION: ~ Avoid duplicating addresses on the system. Installation NMM-100(A), NZM-100(A), and NDM-100(A) modules mount directly to a standard 4" (10.16 cm) square, 2.125" (5.398 cm) deep, electrical box. They may also be mounted to the SMB500 surface-mount box. Mounting hardware and installa- tion instructions are provided with each module. All wiring must conform to applicable local codes, ordinances, and regu- lations. These modules are intended for power-limited wiring only. The NMM-100P(A) module is intended to be wired and mounted without rigid connections inside a standard electrical box. All wiring must conform to applicable local codes, ordi- nances, and regulations. Agency Listings and Approvals In some cases, certain modules may not be listed by certain approval agencies, or listing may be in process. Consult fac- to ry for latest listing status. • UL: S635 • ULC: S635 • FM Approved • CSFM: 7300-0028:0230 (NMM-100, NMM-100P, NZM- 100); 7300-0028:0237 (NDM-100) • MEA: 72-01-E Vol. 2 (NMM-100, NMM-100P, NZM-100); 227-03-E Vol: 3 (NDM-100) Product Line Information NOTE:'!\" suffix indicates ULC-listed model. NMM-1 00(A): Monitor module. NMM-1 00P(A): Monitor module, miniature. NZM-100(A): Monitor module, two-wire detectors. NDM-100(A): Monitor module, dual, two independent Class B circuits. SMBS00: Optional surface-mount backbox. NOTE: See installation instructions and refer to the SLC Wiring Manual, PN 52304. DN-6999:C • 10/06/2010 -Page 3 of 4 ISO 9001 1¥1 =I ;0 • 4 ■=I·) ENGINEERING & MANUFACTURING QUALITY SYSTEMS Notifier® and FireWarden® are registered trademarks and FireWatch™ is a trademark of Honeywell International Inc. ©2010 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited. This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118. www.notifier.com Made in the U.S. A. Page 4 of 4 -DN-6999:C • 10/06/2010 LISTING No. CATEGORY: LISTEE: DESIGN: RATING: INSTALLATION: MARKING: APPROVAL: XLF: CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING -BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE 7300-0028:0230 7300 --FIRE ALARM CONTROL UNIT ACCESSORIES/MISC. DEVICES NotifierOne Fire-Lite Place, Northford, CT 06472-1653 Contact: Vladimir Kireyev (203) 484-6277 Fax (203) 484-7309 Email: vladimir.kireyev@honeywell.com Page 1 of 1 Models NMM-100P, NMM-100, and NZM-100 monitor modules; Models NC-100R and NC-100 control modules; and *NZM-100-6 six zone interface signaling device module. Refer to listee's data sheet for additional detailed product description and operational considerations. 15-32 voe In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. Listee's name, model number, electrical rating, and UL label. Listed as control unit accessories for use with listee's separately listed electrically compatible fire alarm control units. Refer to listee's Installation Instruction Manual for details. 7300-0075:0185 08-23-11 rev. mt This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: Authorized By: July 01, 2012 JASON DEWITT, Deputy State Fire Marshal Fire Engineering Division Listing Expires June 30, 2013 NC-100R(A) Relay Module for FireWarden Series Panels General The NC-1 00R(A) Addressable Relay Module provides NOTI- FI ER's Fire Warden Series intelligent control panels with two isolated sets of Form-C dry-contact outputs for activating a variety of auxiliary devices, such as fans, dampers, door hold- ers, control equipment, etc. Addressability allows the dry con- tact to be activated, either manually or through panel programming, on a select basis. Features • Built-in type identification automatically identifies these devices to the control panel. • Internal circuitry and relay powered directly by two-wire SLC loop. • Integral LED "blinks" green each time a communication is received from the control panel and turns on in steady when activated. • High noise immunity (EMF/RFI). • Wide viewing angle of LED. • SEMS screws with clamping plates for wiring ease. • Direct Decade entry of address: 01 -99 with the FireWar- den-100-2(C) and 01 -50 with the FireWarden-50(C). Applications The NC-1 00R(A) may be programmed to operate dry contacts for door holders, Air Handling Unit shutdown, etc., and to reset four-wire smoke detector power. Construction • The face plate is made of off-white heat-resistant plastic. • Controls include two rotary switches for direct-dial entry of address setting. • The NC-1 00R(A) provides two Form-C dry contacts that switch together. Operation Each NC-100R(A) uses one of the addresses on a SLC loop. It responds to regular polls from the control panel and reports its type and status. The LED blinks with each poll received. On command, it activates its internal relay. Rotary switches set a unique address for each module. The address may be set before or after mounting. The built-in TYPE CODE (not settable) will identify the module to the con- trol panel. dn-60383:A2 ~ NOTI Fl ER@ by Honeywell NC-100R(A) Specifications Normal operating voltage: 15 to 32 voe. Maximum SLC current draw: 6.5 mA (LED). Average operating current: 230 µA direct poll (CLIP mode), 255 µA group poll with LED flashing. EOL resistance: not used. Temperature range: 32°F to 120°F (0°C to 49°C). Humidity range: 10% to 93% non-condensing. Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x 1.25" (3.175 cm) deep. Mounts to a 4" (10.16 cm) square x 2.125" (5.398 mm) deep box. Relay Contact Ratings Load Description Application Maximum Current Voltage Rating Resistive Non-Coded 30VDC 3.0A Resistive Coded 30 voe 2.0A Resistive Non-Coded 110 voe 0.9A Resistive Non-Coded 125 VAC 0.9A Inductive (L/R=5ms) Coded 30VDC 0.5A Inductive (L/R=2ms) Coded 30VDC 1.0 A Inductive (PF=0.35) Non-Coded 125 VAC 0.5A dn-60383:A2 • 06/17 /10 -Page 1 of 2 Agency Listings and Approvals In some cases, certain modules may not be listed by certain approval agencies, or listing may be in process. Consult fac- tory for latest listing status. • UL/ULC Listed: S635. • CSFM approved: file 7300-0028:230. • FM approved. • MEA approved: file 72-01-E, Vol. 2. Product Line Information NC-100R: Intelligent addressable relay module. NC-100RA: Intelligent addressable relay module, ULC listed model. SMBSOO: Optional surface-mount backbox. NOTE: For installation instructions, see document /56-2593-001 and refer to the SLC Wiring Manual, document 52304. NOTIFIER® is a registered trademark of Honeywell International Inc. ISO 9001 l➔=i;\04 1 +1 ENGINEERING & MANUFACTURING QUALITY SYSTEMS ©2010 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited. This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118. www.notifier.com Made in the U.S. A. Page 2 of 2 -dn-60383:A2 • 06/17/1 0 LISTING No. CATEGORY: LISTEE: DESIGN: RATING: INSTALLATION: MARKING: APPROVAL: XLF: CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING -BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE 7300-0028:0230 7300 --FIRE ALARM CONTROL UNIT ACCESSORIES/MISC. DEVICES NotifierOne Fire-Lite Place, Northford, CT 06472-1653 Contact: Vladimir Kireyev (203) 484-6277 Fax (203) 484-7309 Email: vladimir.kireyev@honeywell.com Page 1 of 1 Models NMM-1 00P, NMM-100, and NZM-100 monitor modules; Models NC-1 DOR and NC~ 100 control modules; and *NZM-100-6 six zone interface signaling device module. Refer to listee's data sheet for additional detailed product description and operational considerations. 15-32 voe In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. Listee's name, model number, electrical rating, and UL label. Listed as control unit accessories for use with listee's separately listed electrically compatible fire alarm control units. Refer to listee's Installation Instruction Manual for details. 7300-0075:0185 08-23-11 rev. mt This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing sho'uld not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: Authorized By: July 01, 2012 JASON DEWITT, Deputy State Fire Marshal Fire Engineering Division Listing Expires June 30, 2013 TEM NSOR Intelligent Non-Relay Photoelectric Duct Smoke Detector The lnnovairFlex™ Series are the only duct smoke detectors flexible enough to flt configurations from sq uare to rectangu lar and everything in between. Features • Photoelectric, integrated low-flow technology (delector head so ld separately) • Air velocity ratirig from 100 ft/min to 4,000 ft/min • Adjusts to square and rectangular mounting confgurations • Broad ranges for operating temperature (-4°F to l S8°F) and humidity (0% to 95% non-condensing) • Patented tool-free, plug-in sampling tubes • New cover tamper signal • Increased wiring space with a new ¾-inch conduit knockout • Housing has space for mounting a relay module •Easly accessible cocJe wheels on sensor head (sold separately) • Clear cover for convenient visual inspection · UL 268A listed • Remote testing capabil ity • Requires com line power only • NEMA Type 4 UL listed for non-hazard ous indoor and outdoor applications (DNRW only) • UV-res1stan , UL-listed housing and cover material (DNRWonly) Agency Listings @ LISTED <S> APPROVED ~o Ja-n · -~ MSFM approved )12<; The lnnovairFlex Series DNR and DNRW are intelligent (addressable) non-relay photoelectric duct smoke detectors. Like all lnnovairFlex detectors, the DNR and DNRW both feature an adjustable housing design that fits square and rectangular installation footprints, mounts to both round and rectangular ductwork, and utilizes tool-free, plug-in sampling tubes for increased application flexibility and installation ease. These units sense smoke in challenging conditions, operating in airflow speeds of 100 to 4,000 feet per minute, temperatures of -4°F to 158°F, and a humidity range of Oto 95 percent (non-condensing). For even more extreme environments like rooftops, the DNRW's NEMA 4-rated watertight and UV-resistant housing protects against windblown dirt and dust, rain, and hose directed water, enabling it to be installed without a costly enclosure, saving time and money. The lnnovairFlex housing cover isolates the sensor head from the low-flow feature for simple maintenance, and a cover tamper feature initiates a trouble signal for a removed or improperly installed sensor cover. The housing also provides a ¾-inch conduit knockout and ample space to facilitate easy wiring and mounting of a relay module to meet specific application requirements. These detectors can be customized to meet local codes and specifications without additional wiring. The lnnovairFlex line is compatible with all previous lnnovair models, including remote test accessories, for easy retrofits. WARNING: Duct smoke detectors have specific limitations. lnnovairFlex Duct Smoke Detector Specifications The air duct smoke detector shall be a System Sensor lnnovairFlex™ DNR Intelligent Non-Relay Photoelectric Duct Smoke Detector and DNRW Watertight NEMA 4 Duct Smoke Detector. The detector housing shall be UL listed per UL 268A specifically for use in air handling systems. The flexible housing of the duct smoke detector fits both square and rectangular footprints. The detector shall operate at air velocities of 100 ft/min to 4,000 ft/min (0.5 m/sec to 20.32 m/sec). The unit shall be capable of providing a trouble signal in the event that the sensor cover is removed or improperly installed. It shall be capable of local testing via mdg11elic wv1td1 01 remote Le~t1ng using Lhe RI Sl 51 KEY remote test stal1on. Terminal connections shall be of the strip and clamp method su1Lable for 12-18 AWGw1ring. Siz,:,:: (Rectangulc1r) !Squart1) f.nvirnnmental Rating: Operaunq fernperature Range: ~,tordqt' iemperature Range: C'per,Hir'~J Humidity Range· f,ir Duct Velocity: DCOIL (it lnduded): RAl 00Z R I S I :J 1 /R I S I :J 1 Kt Y 14.38 in (37 cm) Length; 5 in (12.7 cm) Width; 2.5 in (6.6 cm) Depth 7.7S in (19.7 cm) I ength; 9 in (22.9 cm) Width; 2.5 in (6.35 cm) Depth 1.6 lb (0.73 kg) NEMA 4 (DNRW only) -4°F to l S8°F (-20°( to 70°() -22°F to l S8°F (-30°C to 70° C) 0% to 95% relative humidity (non-condensing) 100 Lo 4,000 ft/rni11 (0.5 to 20.32 m/s) 17.5 -26.4 voe, 95 mA max 0mA 12 mA Max. 0 rnA 12 rnA Max. Installing the lnnovairFlex Sampling Tube The lnnovairFlex sampling tube may be insta lled from the front or back of the detector. The rube locks securely into place and can be removed by releasing the fron t 01 rear locking tab (front locking tab shown elow right). LISTING No. CATEGORY: LISTEE: DESIGN: RATING: INSTALLATION: MARKING: APPROVAL: CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING -BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE 3242-1653:0209 3242 --DUCT SMOKE DETECTOR, PHOTO. (W/ OR W/O BASE) C4 Page 1 of 1 System Sensor, Unincorporated Div of Honeywell lnt'l lnc.3825 Ohio Ave, St. Charles, IL 60174 Contact: Trish Linhart (630) 377-6580 Fax (630) 377-7245 Email : trish.linhart@systemsensor.com Models DNR, DNRW, DNRHS and DNRECL* analog photoelectric duct smoke detector housings. The units consist of a duct detector housing, exhaust tubes, and separately listed compatible detector head. Model DNRW is a Type 4(NEMA4) watertight enclosure. Refer to listee's data sheet for additional detailed product description and operational considerations. 24 voe In accordance with listee's printed installation instruction, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. Listee's name, model number, rating, air velocity and UL label. Listed as conventional photoelectric duct smoke detector housing for use with separately listed fire alarm control units. Refer to listee's Installation Instruction Manual for details. *Rev. 03-23-10 fm This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria . Refer to listee's data sheet, installation instructions and/or other Date Issued: Authorized By: July 01, 2012 JASON DEWITT, Deputy State Fire Marshal Fire Engineering Division Listing Expires June 30, 2013 ,,,, COOPER Notification Strobe, Horn Strobe, and Horn Notification Appliances ,-, R - Description: The Wheelock® Exceder™ Series of notification appliances feature a sleek modern design that will please building owners with reduced total cost of ownership. Installers will benefit from its comprehensive feature list, including the most candela options in one appliance, low current draw, no tools needed for setting changes, voltage test points, 12/24 VDC operation, universal mounting base and multiple mounting options for both new and retrofit construction. The Wheelock® Exceder™ Series incorporates high reliability and high efficiency optics to minimize current draw allowing for a greater number of appliances on the notification appliance circuit. All strobe models feature _an industry first of 8 candela settings on a single appliance. Models with an audible feature 3 sound settings (90, 95, 99 dB). All switches to change settings, can be set without the use of a tool and are located behind the appliance to prevent tampering. Wall models feature voltage test points to take readings with a voltage meter for troubleshooting and AHJ inspection. The Wheelock® Exceder™ Series of wall and ceiling notification appliances feature a Universal Mounting Base (UMB) designed to simplify the installation and testing of horns, strobes, and combination horn strobes. The separate universal mounting base can be pre-wired to allow full testing of circuit wiring before the appliance is installed and the surface is finished. It comes complete with a Contact Cover for protection against dirt, dust, paint and damage to the contacts. The Contact Cover also acts as a shunting device to allow pre-wire testing for common wiring issues. The Contact Cover is polarized to prevent it from being installed incorrectly and prevents the appliance from being installed while it is on the UMB. When the Contact Cover is removed the circuit will show an open until the appliance is installed. The UMB allows for consistent installation and easy replacement of appliances if required. Wall models provide an optional locking screw for extra secure installation, while the ceiling models provide a captivated screw to prevent the screw from falling during installation. Compatibility and Requirements -Save up to 48% in current draw* -Up to 9 models now in 1 appliance -Save up to 14% cost of installation** 0 e:! Sleek Modern Aesthetics Finger Slide Switches Voltage Test Points Multiple Voltages 3 Audible Settings 90, 95, 99 dB 8 Candela Settings *** Wall -15/1575/30/75/95/110/135/185 Ceiling -15/30/60/75/95/115/150/177 Universal Mounting Base *** Ceiling and Wall Mounts to 5 Backbox Types Environmentally Friendly Low Current Draw -Synchronize using the Wheelock• Sync Modules or panels with built-in Wheelock• Patented Sync Protocol -Compatible with UL "Regulated Voltage" using filtered VDC or unfiltered VRMS input voltage -Strobes produce 1 flash per second over the "Regulated Voltage" range * Compared to competitive models ** Compared to previous models *** Patented NOTE: All CAUTIONS and WARNINGS are identified by the symbol A. All warnings are printed in bold capital letters. A WARNING: PLEASE READ THESE SPECIFICATIONS AND ASSOCIATED INSTALLATION INSTRUCTIONS CAREFULLY BEFORE USING, SPECIFYING OR APPLYING .THIS PRODUCT. VISIT WWW.COOPERNOTIFICATION.COM OR CONTACT COOPER NOTIFICATION FOR THE CURRENT INSTALLATION INSTRUCTIONS. FAILURE TO COMPLY WITH ANY OF THESE INSTRUCTIONS, CAUTIONS OR WARNINGS COULD RESULT IN IMPROPER APPLICATION, INSTALLATION AND/OR OPERATION OF THESE PRODUCTS IN AN EMERGENCY SITUATION, WHICH COULD RESULT IN PROPERTY DAMAGE, AND SERIOUS INJURY OR DEATH TO YOU AND/OR OTHERS. General Notes: General Notes: • Strobes are designed to flash at 1 flash per second minimum over their "Regulated Voltage Range". • All candela ratings represent minimum effective strobe intensity based on UL Standard 1971. • Series Exceder Strobe products are Listed under UL Standards 1971 and 464 for indoor use with a temperature range of 32°F to 120°F (0°C to 49°C) and maximum humidity of 93% (± 2%) UL 464 (85% UL 1971). • Series Exceder horns are under UL Standard 464 for audible signal appliances (Indoor use only). Model ST STC Model HSC Model HS HSC Model HS HSC Regulated Voltage Range voe 8.0-33.0 8.0-33.0 Regulated Voltage Range voe 8.0-33.0 8.0-33.0 Regulated Voltage Range VOC 8.0-33.0 8.0-33.0 Regulated Voltage Range VOC 8.0-33.0 8.0-33.0 Horn Ratings per UL Anechoic Model Regulated Voltage Range voe HN 16-33.0 HNC 16-33.0 HN 8.0-17.5 HNC 8.0-17.5 24 voe; 24 FWR 15 15/75 30 60 75 95 110 115 135 150 177 0.057 0.070 0.085 0.135 0.163 0.182 0.205 0.061 0.085 0.103 0.135 0.163 0.182 0.205 0.253 24VOC 15 15/75 30 60 75 95 110 115 135 150 177 0.082 0.095 0.102 0.148 0.176 0.197 0.242 0.082 0.102 0.141 0.1 48 0.176 0.197 0.242 0.282 UL Max Current* at Anechoic 95 dBA 24VOe 15 15/75 30 60 75 95 110 115 135 150 177 0.073 0.083 0.087 0.139 0.163 0.186 0.230 0.073 0.087 0.128 0.139 0.163 0.186 0.230 0.272 UL Max Current* at Anechoic 90 dBA 24VOe 15 15/75 30 60 75 95 110 115 135 150 177 0.065 0.G75 0.084 0.136 0.157 0.1 84 0.226 0.065 0.084 0.120 0.136 0.157 0.184 0.226 0.267 99 dB 95 dB 90 dB 0.064 0.044 0.022 0.084 0.044 0.022 0.047 0.026 0.017 0.047 0.026 0.017 12VOe 185 15 15/75 0.253 0.110 0.140 0.110 12VOC 185 15 15/75 0.282 0.125 0.159 0.125 12VOe 185 15 15/75 0.272 0.122 0.153 0.122 12VOe 185 15 15/75 0.267 0.120 0.148 0.120 * UL max current rating is the maximum RMS current within the listed voltage range (16-33 voe for 24 voe units). For strobes the UL max current is usually at the minimum listed voltage (1 6 voe for 24 voe units). For audibles the max current is usually at the maximum listed voltage (33 voe for 24 voe units). For unfiltered ratings, see installation instructions. Specification & Ordering Information Horn Strobes Strobes Strobe Candela *12 VDC models feature 15 & 15/75 settings Model Legend HN = Horn ST = Strobe HS = Horn Strobe C = Ceiling Mount = Whit~ = Red A = Agent Lettering (Strobes only) AL= Alert Lettering (Strobes only) N = No Lettering (Strobes only) Example 1: STRC = Strobe, Red, Ceiling Mount Example 2: HSR = Horn Strobe, Red, Wall Mount Example 3: HSW = Horn Strobe, White, Wall Mount Example 4: STW-AL = Strobe, White, Wall Mount, Alert Lettering Sync w/ DSM or X X 12/24 VDC* X X X Mounting Options UMB** UMB** UMB** **UMB = Universal Mounting Base ✓' /ti Example: HSWC NOTE: Due to continuous development of our products, specifications and offerings are subject to change without notice in accordance with Cooper Wheelock Inc., dba Cooper Notification standard terms and conditions. Architects and Engineers Specifications The notification appliances shall be Wheelock· Exceder™ Series HS Audible Strobe appliances, Series ST Visual Strobe appliances • _ and Series HN Audible appliances or approved equals. The Series HS and ST Strobes shall be listed for UL Standard 1971 (Emergency Devices for the Hearing-I mpaired) fo r Indoor Fire Protection Service. The Series HS and HN Audibles shall be UL Listed under Standard 464 (Fire Protective Signaling). All Series shall meet the requirements of FCC Part 15 Class 8. All inputs shall be compatible with standard reverse polarity supervision of circuit wiring by a Fire Alarm Control Panel (FACP) with the ability to operate from 8 to 33 VDC. .. _ Indoor wall models shall incorporate voltage test points for easy voltage inspection. The Series HS Audible Strobe and ST Strobe appliances shall produce a flash rate of one (1) flash per second over the Regulated Voltage Range and shall incorporate a Xenon flashtube enclosed in a rugged Lexan® lens. The Series shall be of low current design. Where Multi-Candela appliances are specified, the strobe intensity shall have 8 field selectable settings at 15, 15/75, 30, 75, 95, 110, 135, 185 candela for wall mount and 15, 30, 60, 75, 95, 11 5, 150, 177 candela for ceiling mount. The selector switch for selecting the candela shall be tamper resistant. The 15/75 candela strobe shall be specified when 15 candela UL Standard 1971 Listing with 75 candela on-axis is required (e.g. ADA compliance). Appliances with candela settings shall show the candela selection in a visible location at all times when installed. The audible shall have a minimum of three (3) field selectable settings for dBA levels and shall have a choice of continuous or temporal (Code 3) audible outputs. The Series HS Audible Strobe, ST Strobe and Series HN Audible shall incorporate a patented Universal Mounting Base that shall allow mounting to a single-gang, double-gang, 4-inch square, 3.5-inch octal, 4-inch octal or 100mm European type back boxes. Two wire appliance wiring shall be capable of directly connecting to the mounting base. Continuity checking of the entire NAC circuit prior to attaching any notification appl iances shall be allowed. Product shall come with Contact Cover to protect contact springs. Removal of an appliance shall result in a supervision fa ult cond ition by the Fire Alarm Control Panel (FACP). The mounting base shall be the same base among all horn, strobe, horn strobe, wall and ceiling models. All notification appliances shall be backwards compatible. The Series HS and ST wall models shall have a low profile measuring 5.24" H x 4.58" W x 2.19" D. Series HN wall shall measure 5.24" H x 4.58" W x 1.6" D. The Series HSC and STC shall been round and have a low profile with a diameter of 6.68" x 2.63" D. Series HNC ceiling shall have a diameter of 6.68" x 1.50" D. When synchronization is required, the appliance shall be compatible with Wheelock®'s DSM Sync Modules, Wheelock® Power Supplies or other manufacturer's panels with built-in Wheelock® Patented Sync Protocol. The strobes shall not drift out of synchronization at any time during operation. If the sync protocol fails to operate, the strobe shall revert to a non-synchronized flash-rate and still maintain (1) flash per second over its Regulated Voltage Range. The appliance shall also be designed so that the aud ible signal may be silenced while maintaining strobe activation when used with Wheelock® synchronization protocol. Wall Appliances -UL Standard 1971, UL Standard 464, California State Fire Marshal (CSFM), ULC, FM Ceiling Appliances -UL Standard 1971, UL Standard 464, California State Fire Marshal (CSFM), ULC, FM WE ENCOURAGE AND SUPPORT NICET CERTIFICATION 3 YEAR WARRANTY Exceder -Spec Sheet 6/11 NJ Location 273 Branchport Ave. Long Branch, NJ 07740 P: 800-631-2148 F: 732-222-8707 www.coopernotification.com ,,,, Coope-Not;ficaHon ;, Wheelock" (MEDC) SAFEPATH0 WAVifJ) @i COOPER Notification ·- LISTING No. CATEGORY: LISTEE: DESIGN: RATING: INSTALLATION: MARKING: APPROVAL: CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING -BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE 7125-0785:0168 7125 --FIRE ALARM DEVICES FOR THE HEARING IMPAIRED Cooper Wheelock lnc.7246 16th St. E., Ste. 105, Sarasota, FL 34243 Contact: Tom Conover (941) 487-2336 Email : thomas.conover@cooperindustries.com Page 1 of 1 Exceder Series: Models ST strobe, HS horn strobe and HN horn. Model ST is a synchronous and non-synchronous strobe light. Model HS a visual/audible appliance and Model HN is an audible signal appliance. All units followed by R (red) or W (white). Additionally, a 'C' may be added for ceiling models and/or a '-NR' may be added for non-resettable models. For non -NR models and optional 'S' for silver fascia may be added*. Refer to listee's data sheet for additional detailed product description and operational considerations. Electrical: 12 VDC/24VDC/FWR Candela (wall)*: 15, 15/75, 30, 75, 95, 110, 135 & 185 Candela (ceiling)*: 15, 30, 60, 75, 95, 115, 150, & 177 In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. All models are for indoor use and for wall mount only or ceiling mount only* Listee's name, model number, electrical/candela rating, and UL label. Listed as horn for fire alarm signaling and strobe, horn/strobe for the hearing impaired when used with separately listed electrically compatible fire alarm control units. Refer to listee's Installation Instructions Manual for details. *Rev. 9-24-09 fm This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: Authorized By: July 01, 2012 JASON DEWITT, Deputy State Fire Marshal Fire Engineering Division Listing Expires June 30, 2013 .. ,,,,, COOPER Notification Weatherproof Appliances -Series AH Audibles, AS Audible Strobes, MT Multitone Strobes, RSS Strobes and ET70 Speaker Strobes and Weatherproof Mounting Accessories Description: Designed for life safety, performance and reliability, Cooper Notification's Wheelock cost effective weatherpoof notification appliances include: Weatherproof Appliances Series Strobes Horn Strobes Horns Multitone Horn Strobes Multitone Horns Speaker Strobes Speakers RSSWP ASWP AH-24WP, AH-1 2WP MTWP MT ET70WP ET-1010 All strobe models are UL dual listed -meeting both UL 1638 and UL 1971 requirements. As dual listed appliances, these weatherproof strobes, horn strobes and speaker strobes are listed for outdoor applications under UL 1638 as well as under UL 1971 , the Standard for Safety Signaling Devices for Hearing Impaired. With an extended temperature range of -31°F to 150°F (-35°C to 66°C), Wheelock weatherproof appliances meet or exceed UL outdoor test requirements for rain, humidity and corrosion resistance while providing multiple strobe intensity options, including the highest strobe ratings available for area coverage per NFPA 72 strobe spacing tables (up to 185 candela for wall mounting and 177 candela for ceiling mounting). To enable weatherproof mounting, Cooper Notification provides the industry's widest choice of mounting options for surface or unique semi-flush installation. Models are available for surface mounting to Wheelock weatherproof backboxes on walls or ceilings. The optional WP-KIT allows the weatherproof backboxes (108, WPBB or WPSBB) to be mounted to a recessed electrical box for concealed conduit installation. For semi-flush installation, the WPA * and WFPA * kits allow a customer to mount the weatherproof appliances to a recessed electrical box without the need for an external weatherproof backbox. See the Backboxes, Plates and Gaskets Table on page three of this document for a summarization of these mounting options and the required accessories. <§> E5946 151-92-E 7125-0785131 (ASWP) S5391 7125-0785146 (ET70WP) S2652 7125-0785:156 (MTWP) 7300-0785:154 (RSSWP) APPROVED * □ I i I All models may be synchronized using the Wheelock DSM Sync Modules, Wheelock Power Supplies or other manufacturers panels incorporating the Wheelock Patented Sync Protocol. The horn output of horn strobes can be independently controlled on 2-wire circuits using the Wheelock patented sync protocol. MTWP horn strobe models are 4-wire appliances; the strobes can be synchronized while the audible can be connected to a coded fire alarm system or can be set to produce any of eight selectable tones. Features: Approvals include: UL Standards 1971, 1638, 464 and 1480 California State Fire Marshal (CSFM), New York City (MEA), Factory Mutual (FM), Chicago (BFP) and ULC . See agency approvals by model number on page two of this document Compliance with the following requirements: NFPA, UFC , ANSI 117.1 , OSHA Part 29, 1910.165, ADA Weatherproof with extended temperature range of -40°F to 150°F (-40°C to 66°C)* Dual Listed strobe models (UL 1638 and UL 1971) Industry's highest strobe candela options Synchronize using the Wheelock Sync Modules or panels with built-in Wheelock Patented Sync Protocol Models with field selectable tone, dBA and candela settings Wall or ceiling mounting options Surface of semi-flush mounting IN/OUT wiring termination accepting two #12-18 AWG wires at each terminal The series RSSWP, ASWP, AH-24WP, MTWP-2475W, and MT-12/24 have UL / ULC approval down to -40°F. The ET-1010 and ET70WP have UL approval down to -40°F. The AH-12WP has UL approval down to -31 °F. NOTE: All CAUTIONS and WARNINGS are identified by the symbol A. All warnings are printed in bold capital letters. ~A WARNING: PLEASE READ THESE SPECIFICATIONS AND ASSOCIATED INSTALLATION INSTRUCTIONS CAREFULLY BEFORE USING, SPECIFYING OR APPLYING THIS PRODUCT. VISIT WWW.COOPERNOTIFICATION.COM OR CONTACT COOPER WHEELOCK FOR THE CURRENT INSTALLATION INSTRUCTIONS. FAILURE TO COMPLY WITH ANY OF THESE iNSTRUCTIONS, CAUTIONS OR WARNINGS COULD RESULT IN IMPROPER APPLICATION, INSTALLATION AND/OR OPERATION OF THESE PRODUCTS IN AN EMERGENCY SITUATION, WHICH COULD RESULT IN PROPERTY DAMAGE, AND SERIOUS INJURY OR DEATH TO YOU • AND/OR OTHERS. General Notes: Strobes are designed to flash at 1 flash per second minimum over their UL Listed Regulated Voltage Range. All candela ratings represent minimum effective Strobe intensity based on UL Standards 1971 and 1638 as indicated in candela ratings table. Wall Mount RSSWP -MTWP ASWP ET70WP ~ IOb( RSSWP-24 75W-FR Red RSSWP-24 75W-FW White RSSWP-24MCWH-FR Red RSSWP-24MCWH-FW White P. u ''b, ·:J 3trobc ASWP-2475W-FR Red ASWP-24MCWH-FR Red ASWP-24MCWH-FW White fl. u1t1-10no Strobe -MTWP-2475W-FR Red MTWP-2475W-FW White MTWP-24MCWH-FR Red MTWP-24MCWH-FW White :... ..,.::akJr StroDe ET70WP-2475W-FR Red ET?0WP-24 7 5W-FW White ET70WP-24185W-FR Red ET70WP-24185W-FW White ET70WP-24135W-FR Red ET70WP-24135W-FW White Order Code 9013 3034 5161 5165 9012 5137 5140 8420 3112 5132 5134 9077 3179 4885 4891 4872 4875 Ceiling Mount RSSWP MTWP ASWP ET70WP Strobe RSSWP-2475C-FR Red RSSWP-24 75C-FW White RSSWP-24MCCH-FR Red RSSWP-24MCCH-FWWhite Audibie Strobe ASWP-2475C-FR Red ASWP-2475C-FW White ASWP-24MCCH-FR Red ASWP-24MCCH-FW White Multi-tone Strobe MTWP-2475C-FR Red MTWP-2475C-FW White MTWP-24MCCH-FR Red MTWP-24MCCH-FW White Speaker Strobe ET70WP-2475C-FR Red ET70WP-2475C-FW White ET70WP-24177C-FR Red ET70WP-24177C-FW White ET70WP-24115C-FR Red ET70WP-24115C-FW White Candela Ratings Order Code 4338 4446 5167 5187 4251 4502 5149 5157 4457 4478 5102 5122 4452 4454 4845 4859 4550 4732 Wall or Ceiling Mount MT AH ET-1010 Audible Order Code AH-24WP-R Red 7416 AH-12WP-R Red 7415 Horn MT-12/24-R Red 5023 Speaker ET-1010-R Red 3135 ET-1010-W White 3137 UL Max. Current AH 24 voe 12VDC High (99) dBA 0.080 0.192 Med (95) dBA 0.043 0.108 Low (90) dBA 0.021 0.058 UL Reverberant dBA@ 10 Feet Watts 1/8 1/4 1/2 1 2 4 8 ET-1010 77 80 83 86 87 92 94 ET70WP 78 81 84 87 90 93 95 I UL 1971 UL 1638 UL 1638 RSS, ET70WP and ASWP Model Number Agency Approvals Series @-??OF @ -40°F MTWP UL Max Current (Strobe Onlv) High Med Low Strobe UL MEA CSFM FM BFP 2475 30** 180 115 0.138 0.168 0.155 0.150 RSSWP-2475 X X X X - 135 135 56 0.300 0.355 0.340 0.335 MCWH 185 185 77 0.420 0.480 0.465 0.460 RSSWP-24MCWH X -X -- RSSWP-24MCCH X -X -- Audible Strobe 115 115 47 0.300 0.355 0.340 0.335 MCCH ASWP-2475 X X X X X 177 177 73 0.420 0.480 0.465 0.460 ASWP-MCWH X -X --- 24185 185 185 77 0.420 **Wall mount rating only 24177 177 177 73 0.420 ASWP-MCCH X -X -- Multitone Strobe MTWP-2475 X X X X - ---MTWP-MCWH X -X - UL Max. Current MTWP/MT MT MTWP-MCCH X -X -- (Audible) 24 voe 12VDC Horns/Audibles --dBA HI STD HI STD AH-24WP X X X X X ----Horn 0.1 08 0.044 0.177 0.034 AH-1 2WP X X X X X ----~ 0.053 0.024 0.095 0.020 MT-12/24 X X X X X March Time 0.104 0,038 0.142 0.034 Speaker Strobe Code 3 Horn 0.091 0.035 0.142 0.034 ET70WP-2475 X -X X - Code 3 Tone 0.075 0.035 0.105 0.021 ET?0WP-185 X -X X - ~Whoop 0.098 0.037 0.142 0.035 ET?0WP-177 X -X X - riren 0.104 0.036 0.152 0.030 Hi/Lo 0.057 0.025 0.114 0.026 ET70WP-115 X -X X - ET70WP-135 X -X X - • Mounting Accessories □'□·: ....... -·. ! ) ' . . .. WFP WFPA Gasket Kit Order Code WP-KIT 4486 Flush Plates WFPA-R Red 4698 WFPA-W White 4701 WFP-R Red 4696 WFP-W White 4697 Back boxes IOB-R* Red 5046 IOB-W* White 5047 WPSBB-R* Red 9751 WPS88-W* White 3033 WP88-R* Red 9014 WP88-W* White 4692 W8B-R Red 2959 WBB-W White 2960 108 WPSBB WPBB WBB Mounting Options: Backboxes, Plates, Gasket Kits Surface Mount Exposed Conduit Concealed Conduit RSSWP Strobes WPS8B WPS88 + WP-KIT ET70WP Speaker Strobes 108 108 + WP-KIT ASWP Horn Strobes WPB8 WPB8 + WP-KIT AHWP Horns W88 - ET-1010 Speakers W88 - MTWP Multitone Horn Strobes 108 IOB + WP-KIT Multitone Horn 108 IOB + WP-KIT *10B, WPSBB and WPBB models include weep holes and plug in the event that moisture may have entered the appliance Flush Mount WFP WFP WFPA WFP WFP WFP WFP Wiring Diagrams SERIES MTWP APPLIANCES SYNCHRONIZED STROBE OPERATION WITH CODED FACP SERIES MTWP AUDIBLE APPLIANCE AND STROBE OPERATE IN UNISON. RED AND BLACK SHUNT-WIRES ARE SUPPLIED. FROM PRECEDING APPLIANCE OR FACP + STROBE RED .-------+ TO NEXT APPLIANCE OREOLR AUDIBLE SERIES RSSWP, ASWP, AHWP, MTWP AND MT-12/24 APPLIANCES FROM PRECEDING APPLIANCE OR FACP + + .--------+ TO NEXT APPLIANCE OREOLR MTWP 0 0 } 0 0 Strobe Sync Circuit Module NAC#l PS Audible Power Circuit FACP Supply NAC #2 Note: Strobe circuit requires constant voltage. SERIES RSSWP/ASWP APPLIANCES SYNCHRONIZED W/ DSM MODULE SINGLE CLASS "A" NAC CIRCUIT DSM SYNC ~ ~ FACP RETURN Note: Models are available in Red or White. Contact Customer Service for Order Code and Delivery. #Refer to Data Sheet S7000 for Mounting Options NOTE: Due to continuous development of our products, specifications and offerings are subject to change without notice in accordance with Cooper Wheelock Inc. dba Cooper Notification standard terms and conditions. ARCHITECTS AND ENGINEERS SPECIFICATIONS General " Weatherproof notification appliances shall be UL listed for outdoor use. Weatherproof Strobe appliances shall be listed under UL Standard 1638 (Standard for Visual Signaling Appliances) for Indoor/Outdoor use and UL Standard 1971 (Standard for Safety Signaling Devices for Hearing Impaired). The appliances shall be available for optional wall mounting or ceiling mounting to weatherproof backboxes using either exposed conduit or concealed conduit, or semi-flush mounting to a recessed electrical box in walls or ceilings using Wheelock mounting accessories. Weatherproof Strobes Weatherproof Strobe appliances shall produce a minimum flash rate of 60 flashes per minute over the UL Regulated Voltage Range of 16 to 33 VDC and shall incorporate a Xenon flashtube. The weatherproof strobes shall be available with UL 1971 candela ratings up to 185 cd for wall mounting and 177 cd for ceiling mounting. UL 1638 candela ratings up to 180 cd at 77°F shall be available. The strobes shall operate over an extended temperature range of -40°F to 150°F (-40°C to 66°C) and be listed for maximum humidity of 95% RH. Strobe inputs shall be polarized for compatibility with standard reverse polarity supervision of circuit wiring by a Fire Alarm Control Panel (FACP). Weatherproof Audibles and Audible/Strobe Combinations Weatherproof horns and multitone audibles shall be listed for Indoor/Outdoor use under UL Standard 464. The horns shall be able to produce a continuous output or a temporal code-3 output that can be synchronized. The horns shall have at least 3 sound level settings. Horn/Strobe combinations shall be able to be synchronized on a single NAC. Multitone audibles shall be able to produce 8 distinct tones selectable by dip switch and shall have at least 2 sound level settings. Multitone Audible/Strobe combinations shall have independent inputs for the audible and strobe. The strobes shall be able to be synchronized. The audibles shall be able to be coded when operated on a separate NAC. Weatherproof Speakers and Speaker/Strobes Weatherproof speakers and speaker/strobes shall be listed for Indoor/Outdoor use under UL Standard 1480. All speakers shall provide field selectable taps for 1 /8W to 8W operation for either 25 VRMS or 70 VRMS audio systems and shall incorporate a sealed back construction for extra protection and improved audibility. Speakers without strobes shall be Wheelock Series ET-1010. They shall be listed to produce up to 94 dBA and shall incorporate a vandal resistant grille design. Speaker with strobes shall be Wheelock Series ET70WP. They shall be available for surface or semi-flush mounting to walls or ceilings and shall be listed to produce up to 93 dBA. Synchronization Modules When synchronization of strobes or temporal code-3 audibles is required, the appliances shall be compatible with the Wheelock Series DSM Sync Modules, Wheelock Power Supplies or other manufacturers panels with built-in Wheelock Patented Sync Protocol. The strobes and audibles shall not drift out of synchronization at any time during operation. Series ASWP audibles and strobes shall be able to be synchronized on a 2-wire circuit with the ability to silence the audible if required. The strobes on Series MT multitone audible/strobe appliances shall be able to be synchronized and shall be able to be operated on a separate circuit from the audibles while the audible circuit is connected to a coded or continuous NAC. Weatherproof Mounting Accessories Weatherproof mounting options shall include surface mounting or semi-flush mounting to walls or ceilings. Surface mounted appliances shall mount to Wheelock 1OB, WBB, WPBB or WPSBB weatherproof backboxes using either exposed conduit or concealed conduit. For concealed conduit the weatherproof backbox shall be mounted to a recessed electrical box with Wheelock's WP-KIT to provide a weatherproof seal for the electrical box. Semi-flush mounted appliances shall mount to a recessed electrical box using Wheelock WFP or WFPA flush plates to provide a weatherproof seal between the electrical box and the appliance. WE ENCOURAGE AND SUPPORT NICET CERTIFICATION 3 YEAR WARRANTY S9004 WP 06/11 NJ Location 273 Branchport Ave. Long Branch, NJ 07740 P: 800-631-2148 F: 732-222-8707 www.coopernotification.com Coope,Notificat;o,;, Wheeloc_k" (MEDC) SAFEPATH" WAY'@~ --COOPERNotification .. LISTING No. CATEGORY: LISTEE: DESIGN: CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING -BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE 7125-0785:0131 7125 --FIRE ALARM DEVICES FOR THE HEARING IMPAIRED Cooper Wheelock lnc.7246 16th St. E., Ste. 105, Sarasota, FL 34243 Contact: Tom Conover (941) 487-2336 Email: thomas.conover@cooperindustries.com Page 1 of 2 Models AS-1215, -2415, -1230, -2430, -121575, -241575, -2475 and -24110 audible/strobes for the hearing impaired followed by any three alpha/numeric characters indicating lens orientation, lettering and color. Models AS-1215W, -2415W, -1230W, -2430W, -121575W, -241575W, -2475Wand -24110W audible/strobes for the hearing impaired followed by any three alpha/numeric characters indicating lens orientation, lettering and color. These units with suffix -Ware for wall mount only. *Models AS-121575W and AS-241575W lens color may be white, red, blue, green, or amber. Models AS-241 SC, -2430C, -2475C and -24100C audible/strobes for the hearing impaired followed by two alpha/numeric characters indicating lens lettering, orientation and color. These units are intended for ceiling mount only. Model AH-12, -24, AH-12WP, -24WP audible appliances (no strobe), followed by an alpha or numeric character indicating product color. Model AS-24MCW and AS-24MCC audible/strobe, followed by any two alpha or numeric character indicating lettering and product color. *Lens color may be white, red, blue, green, or amber. Models ASWP-2475W and *ASWP-2475C audible/strobe with integral private mode fire/emergency visual signaling for non-hearing impaired applications. Lens color may be white, red, blue, green, and amber. Both models are suitable for outdoor use when mounted on the Model WPBB back box. Models AS-24MCWH, AS-24MCCH, *ASWP-24MCWH, and *ASWP-24MCCH audible/strobes for the hearing impaired followed by two alpha/numeric characters indicating lens lettering and product color. Units with suffix CH are for ceiling mount only . Units with suffix WH are for wall mount only. *Lens color may be white, red, blue, green, or amber. Refer to the listee's data sheet for detailed product description and operational considerations. *Rev. 10-01-07 This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: Authorized By: July 01, 2012 JASON DEWITT, Deputy State Fire Marshal Fire Engineering r;Jivision Listing Expires June 30, 2013 • RATING: INSTALLATION: MARKING: APPROVAL: NOTE: Listing No. 7125-0785:0131 Page 2 of 2 Electrical: 8-17.5/16-33 VDC/VFWR Flash Rate: 60 flashes/minute Candela: 15: 15cd, 1575: 15/75cd,30:30cd,75:75cd,95:95cd, 100: 100cd, 11 0: 11 0cd MCW: Selectable 15cd, 30cd, 75cd, 11 0cd MCC: Selectable 15cd, 30cd,75cd,95cd MCWH: Selectable 135cd, 185cd (65cd, 90cd at -40 C) MCCH: Selectable 115cd, 177cd (50cd, 75cd at -40 C) In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. Models ASWP-2475W, ASWP-24MCWH, AS-24MCW and AS-24MCWH are for wall mount only. Models ASWP-2475C, ASWP-24MCCH, AS-24MCCH, AND AS-24MCC are for ceiling mount only. Models with suffix -W or WH are for wall mount only. Models with suffix -C or -CH are for ceiling mount only. Listee's name, model number, electrical/candela rating, and UL label. Listed as audible and audible/visual signaling devices suitable for the hearing impaired when used in conjunction with separately listed electrically compatible fire alarm control units. For indoor use only except Models AH-12WP, AH-24WP, *ASWP-2475W, ASWP-2475C, ASWP-24MCWH, and ASWP-24MCCH audible appliances are suitable for indoor/outdoor. For synchronization, Models AS Series must be used with Model SM-12/24, SMX-12/24, DSM-12/24 or DSMX-12/24 sync control module (CSFM Listing No. 7300-0785: 132). Refer to listee's Installation Instruction Manual for details. These appliances can generate a distinctive three-pulse Temporal Pattern Fire Alarm Evacuation Signal (for total evacuation) in accordance with NFPA 72, 2002 Edition. Models AH-12, AH-24, -12WP and -24WP audible devices are not suitable for the hearing impaired applications. *Rev. 10-01-07 This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: Authori zed By: July 01, 2012 JASON DEWITT, Deputy State Fire Marshal Fire Engineering Division Listing Expires June 30, 2013 FUNDAMENTALS OF FIRE Al.ARM SYSTEMS 72-33 FIRE ALARM SYSTEM RECORD OF COMPLETION To be completed by the system installation contractor at the time of system acceptance and approval. 1. PROTECTED PROPERTY INFORMATION Nameofproperty: La Posada De Guadalupe -Phase 1 ( Dorm 1-Dining/Kit) Address: 2 4 7 6 Im a 1 a Dr-Car 1 sbad CA 9 2 0 0 8 Description of property: _M_e_n_s __ S_h_e_l_t _e_r ___________________________ _ Occupancy type: _R_-_l~_B __________________________________ _ Name of property representative: -------------------------------- Address: ________________________________________ _ Phone: __________ _ Fax: __________ _ E-mail: _____________ _ Authority having jurisdiction over this property: __________________________ _ Phone: __________ _ Fax: __________ _ E-mail: _____________ _ 2. FIRE ALARM SYSTEM INSTALLATION, SERVICE, AND TESTING INFORMATION Installation contractor for this equipment: _J_J_J __ E_n_t_e_r~p~r_1_· _s _e_s __________________ _ Address: 533 So. Vinewood Escondido, CA 92029 Phone: ( 7 6 0 ) 7 4 7 -3 0 5 0 Fax: ( 7 6 0 ) 7 4 7 -7 5 61 E-mail: -------------- Service organization for this equipment: _S_a_m_e __________________________ _ Address:----------------------------------------- Phone: __________ _ Fax: __________ _ E-mail: _____________ _ Location of as-built drawings: _______________ _ Location of historical test reports: ___ _ Location of system operation and maintenance manuals: ---=I=n=---=-F-=-A=-C=-=P _________________ _ A contract for test and inspection in accordance with NFPA standards is in effect as of _N~/_A _________ _ Contracted testing company: _________________________________ _ Address: ________________________________________ _ Phone: __________ _ Fax: __________ _ E-mail: _____________ _ Contract expires: ____ _ Contract number: ____ _ Frequency of routine inspections: _____ _ 3. TYPE OF FIRE ALARM SYSTEM OR SERVICE NFPA 72 Chapter Reference of System Type: Chapter 8 Remote Supervising station Name of organization receiving alarm signals with phone numbers (if applicable): Alarm: GMS Phone: 8 0 0 -6 3 4 -3 915 Supervisory:_G_M_S __________________ _ Phone: _____________ _ Trouble: GMS ----------------------Phone: _____________ _ Entity to which alarms are retransmitted: ______________ _ Phone: _________ _ Method of retransmission of alarms to that organization or location: _________________ _ © 2007 National Fire Protection Association NFPA 72 (p. 1 of 5) FIGURE 4.5.2.1 Record of Completion. 2007 Edition @ ,. .. 72-34 NATIONAL FIREALAR\1 CODE 3. TYPE OF FIRE ALARM SYSTEM OR SERVICE (continued) If Chapter 8, note the means of transmission from the protected premises to the central station: ~ Digital alarm communicator O McCulloh O Multiplex O 2-way radio O 1-way radio O N/A If Chapter 9, note the type of connection: 0 Local energy O Shunt O N/A 3.1 System Software Operating system (executive) software revision level: _5_._2 __ N_e_w ____________________ _ Site-specific software revision date: __________ _ Revision completed by: _F_a_c_t_o_r_.y.___ ____ _ 4. SIGNALING LINE CIRCUITS Characteristics of signaling line circuits connected to this system (see NFPA 72, Table 6. 6.1): Quantity: 4 Style: 4 Class: _B _____________ _ 5. ALARM-INITIATING DEVICES AND CIRCUITS Characteristics of initiating device circuits connected to this system (see NFPA 72, Table 6.5): Quantity: ________ _ Style: ___________ _ Class: _______________ _ 5.1 Manual Initiating Devices 5.1.1 Manual Pull Stations Number of manual pull stations: _______ _ Type of devices: 0 Addressable O Conventional 0 Coded O Transmitter O N/A 5.2 Automatic Initiating Devices 5.2.1 Area Smoke Detectors Number of smoke detectors: _1 _______ _ Type of coverage: 0 Complete area ~ Partial area O Nonrequired partial area O N/A Type of devices: ij Addressable O Conventional O Coded O Transmitter O N/A Type of smoke detector sensing technology: 0 Ionization ~ Photoelectric 5.2.2 Duct Smoke Detectors Number of duct smoke detectors: _8 _______ _ Type of coverage: HVAC & S FD I S Type of devices: ~ Addressable r:.J Conventional CJ Coded CJ Transmitter O N/A Type of smoke detector sensing technology: 0 Ionization ~ Photoelectric 5.2.3 Heat Detectors Number of heat detectors: _______ _ Type of coverage: 0 Complete area O Partial area O Nonrequired partial area O N/A Type of devices: 0 Addressable O Conventional O Coded O Transmitter O N/A 5.2.4 Sprinkler Waterflow Detectors Number ofwaterflow detectors: _2 _______ _ Type of devices ~ Addressable O Conventional 0 Coded O Transmitter O N/A 5.2.5 Alarm Verification Number of devices subject to alarm verification: -=N:...:....,_/-=-A-=------- Alarm verification on this system is: 0 Enabled O Disabled O Set for ___ seconds © 2007 National Fire Protection Association NFPA 72 (p. 2 of 5) FIGURE 4.5.2.1 Continued liJ 2007 Edition FUNDAMENTALS OF FIRE ALARM SYSTEMS 72-35 6. SUPERVISORY SIGNAL-INITIATING DEVICES AND CIRCUITS 6.1 Sprinkler System Number of valve supervisory switches:_4 ________ _ Type of devices: ~ Addressable O Conventional O Coded O Transmitter O N/A 6.2 Fire Pump Type of fire pump: 0 Electric O Diesel Type of fire pump supervisory devices: f..l Addressable U Conventional O Coded O Transmitter O N/ A Fire Pump Functions Supervised 0 Fire pump power O Ffre pump running O Fire pump phase reversal O Selector switch not in auto 0 Engine or control panel trouble O Low fuel Other: _________________________________________ _ 6.3 Engine-Driven Generator Type of generator supervisory devices: 0 Add1·essable O Conventional O Coded O Transmitter O N/A 0 Engine or control panel trouble O Generator running O Selector switch not in auto O Low fuel Other: ___________________________________________ _ 7. ANNUNCIATORS 7.1 Annunciator 1 :J Local O Remote Type: 0 Addressable O Directory O Graphic O N/A Location: _______________ _ 7.2 Annunciator 2 :J Local O Remote Type: 0 Addressable O Directory O Graphic O N/A Location: _______________ _ 7.3 Annunciator 3 :J Local 0 Remote Type: 0 Addressable O Directory O Graphic O N/A Location: _______________ _ 8. ALARM NOTIFICATION DEVICES AND CIRCUITS 8.1 Emergency Voice Alarm Service Numbe1· of single voice alarm channels: _____ _ Number of speakers:-~----------- 8.2 Telephone Jacks Number of telephone jacks installed: ______ _ Number of multiple voice alarm channels: _______ _ Number of speaker zones:-------------- Number of telephone handsets stored on site: ______ _ Type of telephone system installed: 0 Electrically powered O Sound powered O N/A 8.3 Nonvoice Audible System Characteristics of notification device circuits connected to this system (see NFPA 72, Table 6.5): Quantity: 3 Style: ___________ Class:_B _____________ _ © 2007 National Fire Protection Association NFPA 72 (p. 3 of 5) F1GURE 4.5.2.1 Continued 2007 Edition lij 72-36 NATIONAL FIRE ALARM CODE 8. ALARM NOTIFICATION DEVICES AND CIRCUITS (continued) 8.4 Types and Quantities of Nonvoice Notification Appliances Installed Bells: _____ With visual device: ____ _ Horns: _____ _ With visual device: _____ _ Chimes: With visual device: -----Bells: With visual device: _____ _ Visual devices without audible devices: _____ _ Other (describe): ________________ _ 9. EMERGENCY CONTROL FUNCTIONS ACTIVATED 0 Hold-open door releasing devices 0 Door unlocking 10. SYSTEM POWER SUPPLY 10.1 Primary Power 0 Smoke management or smoke control 0 Elevator recall 0 Other Nominal voltage _1_2_0_V_A_C __________ _ Amps _3 _________________ _ Overcurrent protection: Type _B_r_k_r _______ _ Amps _2_0 _______________ _ Location (of primary supply panelboard): Disconnecting means location: 10.2 Secondary Power Location: In FACP Type: AGM Nominal voltage: _l _2 __ Current rating: __ _ Number of standby batteries: _2 ________ _ Amp hour rating: _1_2 ______________ _ Location of emergency generator: -------------------------------- Location of fuel storage: ------------------------------------ Calculated capacity of secondary power to drive the system In standby mode: 2 4 hrs In alarm mode: _S __ m_i_n _____________ _ 11. RECORD OF SYSTEM INSTALLATION Fill out after all installation is complete and wiring has been checked for opens, shorts, ground faults, and improper branching, but before conducting operational acceptance tests. The system has been installed in accordance with the following NFPA standards: (Note any or all that apply.) ~ NFPA 72 E NFPA 70, National Electrical Code, Article 760 ~ Manufacturer's published instructions O Other (please specify): __________________ _ System deviations from referenced NFPA standards: ________________________ _ Signed: ____________ _ Printed name: Jim McKinley Date: 3 / 7 / 13 Organization: J_J_J __ E_N_T ________ _ Title: P=--=M'--"----------Phone: 7 6 0 -7 4 7 -3 0 5 0 12. RECORD OF SYSTEM OPERATION All operational features and functions of this system were tested by or in the presence of the signer shown below, on the date shown below, and were found to be operating properly in accordance with the requirements of: ~ NFPA 72 Qi NFPA 70, National Electrical Code, Article 760 ~ Manufacturer's published instructions O Other (please specify): 0 D ce with Inspection and Testing Form (Figure 10.6.2.3) is attached Printed name: Jim McKinley Date: _3....:..../_7__:_/_1_3 ____ _ Title: _P_M ________ _ Phone: 7 6 0 -7 4 7 -3 0 5 0 © 2007 National Fire Protection Association NFPA 72 (p. 4 of 5) FIGURE 4.5.2.1 Continued (.ij 2007 Edition FUNDAMENTALS OF FIRE ALARM SYSTEMS 72-37 13. CERTIFICATIONS AND APPROVALS 13.1 System Installation Contractor pecified herein has been installed and tested according to all NFPA standards cited herein. Printed name:Jim McKinley Date: 3 /7 /13 Title: _P_M _______ _ Phone: 7 6 0 -7 4 7 -3 0 5 0 13.2 System Service Contractor s been installed and tested according to all NFPA standards cited herein. Printed name: Jim McKinley Date: 3/7/13 Title: _P_M ________ _ Phone: 7 6 0 -7 4 7 -3 0 5 0 13.3 Central Station ·11 be.monitored according to all NFPA standards cited herein. Printed name: Jim McKinley Date: 3/7/13 Title: _P_M ________ _ Phone: 760-747-3050 13.4 Property Representative I accept this system as having been installed and tested to its specifications and all NFPA standards cited herein. Signed: ____________ _ Printed name: _________ _ Date: _______ _ Organization: __________ _ Title: ____________ _ Phone: _______ _ 13.5 Authority Having Jurisdiction I have witnessed a satisfactory acceptance test of this system and find it to be installed and operating properly in accordance with its approved plans and specifications, its approved sequence of operations, and with all NFPA standards ted herein. Signed:_,_ ___ ,._~---+-------Printed name:~,11,,J Date:~ 1,e,-!"3 Title:..fY:Nr:( pt£~-Phone~1/t,re5 © 2007 National Fire Protection Association NFPA 72 (p. 5 of 5) FIGURE 4.5.2.1 Continued 2007 Edition G'J