The URL can be used to link to this page

Home My WebLink About221 NORMANDY LN; ; FPR2019-0029; Permit(ity of Carlsbad Print Date: 12/14/2020 Job Address: 221 NORMANDY IN, CARLSBAD, CA 92008-2223 Permit Type: FIRE-Construction Residential Work Class: Parcel U: 2030231600 Track U: Valuation: $0.00 Lot #: Occupancy Group: Project U: #of Dwelling Units: Plan U: Bedrooms: Construction Type: Bathrooms: Orig. Plan Check U: Plan Check U: Project Title: Description: SCHIFF RESIDENCE -NEW 13D SPRINKLER SYSTEM Permit No: FPR2019-0029 Status: Closed - Finaled Single Family Fire Sprinkl Applied: 03/28/2019 Issued: 04/10/2019 Finaled Close Out: 07/06/2020 Inspector: Final Inspection: Applicant: FPContractor: VANGUARD FIRE PROTECTION INC VANGUARD FIRE PROTECTION INC MAX HICKMAN 417 CARLSBAD VILLAGE DR 417 CARLSBAD VILLAGE DR CARLSBAD, CA 92008-2302 CARLSBAD, CA 92008-2302 (760) 727-8540 (760) 727-8540 FEE AMOUNT FIRE NFPA 13D Single Family System (Insp/Bldg) $125.00 FIRE NFPA 13D Single Family System (Plan Review) $246.00 Total Fees: $371.00 Total Payments To Date: $371.00 Balance Due: $0.00 Fire Department Page 1 of 1 1635 Faraday Avenue, Carlsbad CA 92008-7314 1 760-602-4665 1 760-602-8561 f I www.carlsbadca.gov f f&2.619 -,o 002,1 SCHIFF RESIDENCE Drawing Date:2-27-19 Page 1 HYDRAULIC DESIGN INFORMATION SHEET Job Name: SCHIFF RESIDENCE Location: 221 NORMANDY LN CARLSBAD, CA 92008 Drawing Date: 2-27-19 Contractor: VANGUARD FIRE PROTECTION P0 BOX 1300 VISTA CA 92085-1300 760-727-8540 Designer: SB Calculated By: SprinkCAD www.sprinkcad.com 451 N. Cannon Ave. Lansdale, PA 19446 Construction: V-B Reviewing Authorities : CFD Remote Area Number: 1 Telephone: Occupancy: RES SYSTEM DESIGN Code:NFPA 13D Hazard: System Type:WET Area of Sprinkler Oper. 512 sq ftl Sprinkler or Nozzle Density (gpm/sq ft) RES I Make: SENJU Area per Sprinkler 256.0 sq ftl Model: RCRES Hose Allowance Inside 0 gpm I K-Factor: 4.90 Hose Allowance Outside 5 gpm Temperature Rating: 162 CALCULATION SUMMARY 2 Flowing Outlets gpm Required: 31.6 psi Required: 47.0 @ Source WATER SUPPLY Water Flow Test I Pump Data Date of Test 2-27-19 I Rated Capacity 0 gpm. Static Pressure 74.0 psi I Rated Pressure 0.0 psi I Residual Pres 73.9 psi I Elevation 0 At a Flow of 31 gpm I Make: I Elevation 0" Model: I Location: METER Source of Information: CWD SYSTEM VOLUME 19 Gallons Notes: SCHIFF RESIDENCE Drawing Date:2-27-19 Page 2 HYDRAULIC CALCULATION DETAILS HYDRAULIC QTY DESCRIPTION LENGTH C ID TOTALS Hydr Ref W Required at Hyd Area 1 26.3 psi 1 1" CPVC 90 Eli 5' 150 1.101 1 Pipe 1" PV 8' 150 1.101 Elevation Change 8'0" 1 1" Thrd Check Valve Generic NFPA Va 5' 120 1.049 Hydr Ref BOR Required at BASE OF RISER 33.2 psi 1 i" Sweatd 90 Eli 3' 150 0.995 1 Pipe 1" Kx21 Copper 3' 150 0.995 1 1" Sweatd 90 Eli 3' 150 0.995 Fixed Flow Outside Hose Allow. 1 Pipe 1-1/4" PVx15 60' 150 1.380 3 1-1/4" CPVC 90 Eli 18' 150 1.380 1 1" Thrd Other Valve METER " " w/Bai CHART LOSS 1 Pipe 1" Kx21 Copper 5' 150 0.995 Elevation Change 2'0" FLOW LOSS gpm psi 27 27 1.4 27 0.9 3.5 27 1.1 27 27 0.7 27 0.6 27 0.7 5 gpm 32 3.0 32 2.3 32 4.3 32 1.3 0.9 Hydr Ref SC Required at Source 47.0 psi Water Source 74.0 psi static, 73.9 psi residual S 31 gpm 32 gpm 73.9 psi SAFETY PRESSURE 26.9 psi Available Pressure of 73.9 psi Exceeds Required Pressure of 47.0 psi This is a safety margin of 26.9 psi or 36 % of Supply Maximum Water Velocity is 9.1 fps SCHIFF RESIDENCE Drawing Date:2-27-19 Page 3 FITTING NAME TABLE ABBREV. NAME C Coupling E 90' Standard Elbow F 45' Elbow S Straight Flow Thru Tee T 90' Flow Thru Tee V Valve LEGEND HYD REF Hydraulic reference. Refer to accompanying flow diagram. K FACTOR Flow factor for open head or path where Flow (gpm) = K x -\/P Qa Flow added or subtracted Qt Total flow DIA Actual internal diameter of pipe C Hazen Williams pipe roughness factor Pf/ft Friction loss per foot of pipe PIPE Length of pipe FTNG'S Number of fittings. See table above. TOTAL Total length (PIPE + FTNG'S) Pt Total pressure (psi) at fitting Pe Pressure due to change in elevation where Pe = 0.433 x change in elevation Pf Friction loss (psi) to fitting where Pf = 1 x 4.52 x (Q/C)"1.85 / ID'4.87 Pv Velocity pressure (psi) where Pv = 0.001123 x Q"2/ID"4 Pn Normal pressure (psi), where Pn = Pt - Pv NOTES: - Pressures are balanced to 0.01 psi. Pressures are listed to 0.1 psi. Addition may vary by 0.1 psi due to accumulation of round off. - Calculations conform to NFPA 13. - Velocity Pressures are not considered in these Calculations SCHIFF RESIDENCE Drawing Date:2-27-19 Page 4 NODE ELEVATION SPRINKLER PRESSURE ACTUAL MINIMUM ACTUAL NUMBER K-FACTOR FLOW FLOW DENSITY (FT) (GPM/(PSI"*)) (PSI) (GPM) (GPM) (GPM/SQ. FT) 1 27.50 7.0 is 27.00 4.90 7.0 13.0 13.0 0.05 2 27.50 7.7 2S 27.00 4.90 7.7 13.6 13.0 0.05 10 27.50 8.7 W 8.50 26.3 Max velocity of 9.05 occurs in the pipe from 10 TO W Nodes with "S" indicate a node at the top of a sprig or bottom of drop pendent. The node without an "5" is on the branch. SCHIFF RESIDENCE Drawing Date:2-27-19 Page 5 HYD. Qa DIA. FITTING PIPE Pt Pt REF "C" TYPES FTNG'S Pe Pv ******* NOTES ******* POINT Qt Pf/ft TOTAL Pf Pn PATH 1 FROM HYDRAULIC REFERENCE 1 TO W (PRIMARY PATH) 12.98 1.101 1E 0.50 7.0 7.0 K = 4.90 is C=150 5.00 -0.2 0.0 12.98 0.031 5.50 0.2 7.0 Vel = 4.42 1.101 4E ------------------------------------------------------------------------- 30.52 7.0 7.0 EqK = 4.92 1 C=150 iT 26.00 0.0 0.0 12.98 0.031 is 56.52 1.7 7.0 Vel = 4.42 13.63 1.101 3E ------------------------------------------------------------------------- 45.47 8.7 8.7 10 C=150 4T 36.00 8.2 0.0 See PATH 2 26.61 0.115 is ------------------------------------------------------------------------- 81.47 9.4 8.7 Vel = 9.05 W 26.61 26.3 K = 5.18 PATH 2 FROM HYDRAULIC REFERENCE 2 TO 10 13.63 1.101 1E 0.50 7.7 7.7 K = 4.90 2S C=150 5.00 -0.2 0.0 13.63 0.033 5.50 0.2 7.7 Vel = 4.64 1.101 iT ------------------------------------------------------------------------- 20.71 7.7 7.7 EqK = 4.91 2 C=150 4S 9.00 0.0 00 13.63 0.033 ------------------------------------------------------------------------- 29.71 1.0 7.7 Vel = 4.64 10 13.63 8.7 K = 4.62 UNITS - DIAMETER (INCH) LENGTH (FOOT) FLOW (GPM) PRESSURE (PSI) FPK2019,00 tyco Fire & Building IjProducts Technical Services: Tel: (800) 381-9312 I Fax: (800) 791-5500 ,a rapid response TU HOME FIRE SPRINKLER SYSTEM BlazeMaster CPVC Fire Sprinkler Pipe & Fittings Submittal Sheet General Description Tyco® CPVC Pipe and Fittings pro- duced by Tyco Fire & Building Prod- ucts (TFBP) are designed exclusively for use in wet pipe automatic fire sprin- kler systems. The Tyco CPVC Pipe and Fittings are produced from Blaze- Master® CPVC compound that is a specially developed thermoplastic compound composed of post chlorin- ated polyvinyl chloride (CPVC) resin and state of the art additives. Tyco CPVC Pipe and Fittings are easier to install than traditional steel pipe sys- tems, and at the same time, provide superior heat resistance and strength as compared to traditional CPVC and PVC piping materials used In the plumbing trade. Various adapters are available to connect CPVC pipe to me- tallic piping. All female pipe thread adapters have brass inserts for dura- bility. Grooved adapters connect di- rectly to grooved end valves and me- tallic pipe, with flexible grooved end couplings. NOTICE] Tyco® CPVC Pipe and Fittings pro- duced with BlazeMaster® CPVC com- pound described herein must be in- stalled and maintained in compliance with this document and with the appli- cable standards of the National Fire Protection Association, in addition to the standards of any authorities having jurisdiction. Failure to do so may im- pair the performance of these devices. The owner is responsible for maintain- ing their fire protection system and de- vices in proper operating condition. The installing contractor or sprinkler manufacturer should be contacted with any questions. Technical Data Sizes 3/4" to 3" Maximum Working Pressure 175 psi Approvals UL, FM, C-UL, NSF, LPCB MEA, and the City of Los Angeles. (Refer to In- stallation Handbook 111-1900 dated June 2008 for exact listing/approval information.) Manufacture Source U.S.A. Material Pipe: ASTM F442, SDR 13.5 Fittings: ASTM F438 (Sch. 40) and ASTM F439 (Sch. 80), ASTM F1970 Color Orange Blaz&MastetO is a registered trademark of The Lubrizol Corporation Page lof2 JUNE, 2008 TFPI9I5 Page 2 of 2 TFP19IS Installation Tyco® CPVC Pipe and Fittings pro- duced by Tyco Fire & Building Prod- ucts (TFBP) are to be installed in accordance with installation Hand- book 111-1900 dated June 2008. Care and Maintenance The owner is responsible for the in- spection, testing, and maintenance of their fire protection system and de- vices in compliance with this docu- ment, as well as with the applicable standards of the National Fire Protec- tion Association (e.g., NFPA 25), in addition to the standards of any authority having jurisdiction. The in- stalling contractor or product manufac- turer should be contacted relative to any questions. Automatic sprinkler systems should be inspected, tested, and maintained by a qualified Inspection Service in accord- ance with local requirements and/or national codes. NOTICE Before closing a fire protection system control valve for inspection or mainte- nance work on the fire protection sys- tem that it controls, permission to shut down the affected fire protection sys- tem must first be obtained from the proper authorities and all personnel who may be affected by this action must be notified. After placing a fire protection system in service, notify the proper authorities and advise those responsible for moni- toring proprietary and/or central sta- tion alarms. Limited Warranty Products manufactured by Tyco Fire & Building Products (TFBP) are war- ranted solely to the original Buyer for ten (10) years against defects in mate- rial and workmanship when paid for and properly installed and maintained under normal use and service. This warranty will expire ten (10) years from date of shipment by TFBP. No warranty is given for products or com- ponents manufactured by companies not affiliated by ownership with TFBP or for products and components which have been subject to misuse, improper installation, corrosion, or which have not been installed, maintained, modi- fied or repaired in accordance with ap- plicable Standards of the National Fire Protection Association, and/or the standards of any other Authorities Having Jurisdiction. Materials found by TFBP to be defective shall be either repaired or replaced, at TFBP's sole option. TFBP neither assumes, nor authorizes any person to assume for it, any other obligation in connection with the sale of products or parts of prod- ucts. TFBP shall not be responsible for sprinkler system design errors or inac- curate or incomplete information sup- plied by Buyer or Buyer's repre- sentatives. In no event shall TFBP be liable, in contract, tort, strict liability or under any other legal theory, for incidental, indirect, special or consequential dam- ages, including but not limited to labor charges, regardless of whether TFBP was informed about the possibility of such damages, and in no event shall TFBP's liability exceed an amount equal to the sales price. This limited warranty sets forth the ex- clusive remedy for claims based on failure of or defect in products, materi- als or components, whether the claim is made in contract, tort, strict liability or any other legal theory. This warranty will apply to the full ex- tent permitted by law. The invalidity, in whole or part, of any portion of this warranty will not affect the remainder. 2008 TYCO FIRE & BUILDING PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446 ®Porrw RESIDENtiAL RISER The Symbction .. Service Pressure: Up to 175 PSi (12,07 BAB) O Minimum Flow Rate for Alarm .8-lOGPM(30.38 I-PM). Maximum Surge:. 18 FPS (5,5 rn/a) a, Usage: Listed CPVC plastic piping systems manufactured by Central Sprinkler Corp., Grinnell Sprinkler Corp., Spears I Manufacturing Co., Hervel and lP( (Scepter). Fltspip&zes..l',1.1/41-i/2'and2' Environmental Specifications: ) Indoor use only -. Temperature range: 40t92Q,(4;5°çIo4C) Service Use: One or two family dwelling NFPA.130 Flow Switch Enclosure: Die-cast, red powdetat finish Cover held In place with tamper resistant screws. ContactRtings: TWO sets of8PDT (Form C) I.i . .,. 15.0 Amps at 125/250 VAC • ....... . . 2.0 Amps at30 VW' Conduit Entrances Two knockouts provided for 1/2. conduit. Switch Contacts: SPOT (Form C) Contact Rating: 3 Arhpa at 260VAC ............ Terminatloner 8' No. 22 AWO Wlre Leads Caution:. This device is gist Intended for applications In explosive environments. FIG. 1 to NOT ttait cuwi ,• wren WQWI 50 CiTt i5 AMSTWG MAN ci SW 0-w ou MOOS a Som arm - ci I/a. ci APPROX. RETARD SETTINGS ON SEC.) 0 A B C 0 E 0 10.25 20.40....3555 5040 60-90 Retard Adjustment: To change time, turn retard adjusting knob (either direction) for desired time delay. Use the minimum amount of retard necessary to prevent false alarms A -B' setting Is usually adequate for this. Factory set at W. FIG.2 OPTIONAL REUEF VALVE K)T sac assa Main Riser ® .Pów-$wflcti ..... . - ,® Test and Drain. iir NPT female filling for relief valve m. roes-s 7 07 1 - SENJU SPRINKLER CO., LTD Residential Lead Free Flat Concealed Sprinkler, Pendent, Model: RC-RES, K-Factor: 4.9, SIN: SS8464 GENERAL DESCRIPTION The Model RC-RES Residential Flat Concealed Sprinklers are automatic sprinklers of the compressed fusible solder type. They are decorative and fast responding. The Cover Plate Assembly hides the Deflector, Heat Responsive. Element etc., which is concealed above the ceiling. The cover plate has a flat profile, and its diameter is extremely small. (2-5/8 inch, 68mm). The push-on and/or thread-on, thread-off design of the concealed cover plate assembly allows for easy installation of the cover plate. Therefore, the Màdel RC-RES should be your first choice when aesthetics is the major consideration for ultimate appeal and unbeatable performance is desired. The Model RC-RES is designed for residential occupancies and is perfect for use in homes, hotels and other living quarters. The Model RC-RES is to be used in wet pipe residential• sprinkler systems for One- and Two- Family Dwellings and Manufactured Homes per NFPA 130; wet pipe residential sprinkler systems for Residential Occupancies up to and Including Four Stories in Height per NFPA 13R; or, wet pipe sprinkler systems for the residential portions of any occupancies per NFPA 13. The Model RC-RES has a 4.9 (70.6 LPM/bar12) K-factor that meets the required residential flow rates ,ith minimal residual pressure, which allows for smaller pipe sizes and water supply requirements. For extended installation flexibility, the Model RC-RES provides 1/2 inch (12.8mm) vertical adjustment. This adjustment in installation decreases the need for precise cutting of the pipe that drops to the sprinkler and allows for a perfect fit with a range of pipe lengths. . The heat sensitivity and water distribution design of Model RC-RES allows for an increased chance of residents to escape or evacuate in case of a fire. However, residential fire sprinkler systems are not a substitute for fire safety awareness or fire safety construction required by building codes. Lead Free" is defined In the Reduction of.Lead in Drinking Water Act (S.3874) endorsed by AWWA's Water Utility Council, and California Assembly Bill #1953 as having.less than or equal to a weighted average of 0.25% lead in wetted surface of pipes, plumbing fittings and fixtures. WARNINGS - The Model RC-RES must be installed and maintained in accordance with the rules stated herein as well as In compliance with the applicable standards of the National Fire Protection Association regulations and the standards of any other authorities having June dlctlon In the event of this condition, consult the authorities having jurisdiction for guidance and approval. Failure to do so may impair the integrity of these devices. It Is the responsibility of the installing contractor to provide a copy of this document to the owner or their representative, and in turn, it is the obligation of the owner to provide a copy of this document to a succeeding owner. The owner Is responsible for maintaining their fire protection system and devices in proper operating condition. The Installing contractor or sprinkler manufacturer should be contacted with any related questions. Document No. U085165 Date : Jan/11/2019 Page 2 of 8 TECHNICAL DATA Approvals: 0UL9 Listed, NSF-61 .6 Sprinkler Identification Number (SIN): SS8464 Maximum Working Pressure: 175ps1 (12.1 bar) Discharge Coefficient (Nominal K-Factor): K=4.9 GPM/psi112 (70.6 LPM/bar112) Temperature Rating: 162°F (72°C) Sprinkler with 140°F (60°C) Cover Plate 175°F (79°C) Sprinkler with 140°F (60°C) Cover Plate 175°F (79°C) Sprinkler with 162°F (72°C) Cover Plate Color Code (Sprinkler) 162°F (72°C): Uncolored 175°F (79°C) White Color Code (Cover Plate) 140°F (60°C): No Mark 162°F (720C): White-Colored Mark Vertical Adjustment: 112 inch (12.8 mm) Cover Plate Finishes: Standard Finishes- White, Ivory, Beige, Brown, Black, Nickel, Wood Grain Custom Finishes- Custom color and custom pattern cover plates are available on special order. Contact a Senju Sprinkler representative with any custom orders. Please see chart on Page 8 for more detail. Physical Characteristics: Ref. Figures 1 and 1-1 1-1'IO tQDmm) Marking Year of Mavuracture - - ':: rk F19C Me £' Control No. _- 607 (Copper Alloy), - . Deflector (Pttosptorus Broyze) Casket P1FE) 25/8 ('68mm) (4 Fusible Metal (Solder) or 3 1/4 (0 83nsi,) l) Heat Collector (Copper) ,rfjoare (06nm) (Si Cover Plate As FIGURE 1. Model RC-RES K-4.9 OPERATION In case of fire, the solder component that holds together the Cover Plate and the Retainer melts. Then the, Cover Plate is released at once. As a result, the Deflector drops down to the intended position. Two Heat Collectors are exposed to fire, and when sufficient heat from the fire Is reached, internal components of the sprinkler fall apart. This leads to the water flow to be distributed on the affected fire area. (Ref. Figure 2) Document No.U085165 Date : Jan/11/2019 Page 3 of 8 DESIGN CRITERIA The herein stated rules for use and installation of Model RC-RES are provided by the manufacturer and must be strictly implemented for safe and full results. NOTES Residential Fire Sprinkler Systems should only be designed and Installed by Individuals who are completely familiar with automatic sprinkler system design, installation procedures, and techniques. Several criteria may apply to the installation and usage of each sprinkler. Consequently, it Is recommended that the sprinkler system designer review and develop a working understanding of the complete fist of criteria prior to initiating the design of the sprinkler system. Questions concerning sprInkler installation and usage criteria, which are not covered by the following instructions should be submitted to your contracted company. Include sketches and technical details, as appropriate. In some Instances, the requirements of this document may concern specifications which are more stringent, and which take precedence over those specified in NFPA 13, 130, 13R, or by the authority having jurisdiction. The Model RC-RES must not be used In applications where the air pressure above the ceiling Is greater than that below. Inspect all sprinklers after installation to ensure that both the gap between the cover plate, ceiling and the 6 slots in the cup are open and free from any air flow Impediment The spray from the sprinkler Is distributed radially outward and downward from the sprinkler deflector. Consequently, the sprinklers must be located such that there will be no blind spaces shielded from spray by partitions, room dividers, overhangs or other parts of the dwelling structure. The number of sprinklers within each compartment (as defined by NFPA 13, 13D, or 13R) must be kept as few as possible. Do NOT use more sprinklers thaA necessary to cover a particular space. Use only the Cover Plate provided for the Model RC-RES. The sprinkler must be secured In place by firmly fastening the sprinkler system piping to the structure. If the sprinkler is not property secured In position, reaction forces resulting from sprinkler operation could alter its orientation and its water distribution pattern. Obstruction to Water Distribution Locations of sprinklers must follow the obstruction rules of NFPA 13, 13D and 13R for Residential Sprinklers. General Service Conditions The Model RC-RES must only be utilized in WET PIPE sprinkler systems. Heat Source Criteria Refer to NFPA 13D, 13R or 13 for the requirements relating to the prevention of possible activation of the Heat Responsive Element of Model RC-RES, due to the exposure of a heat source other than an actual fire. Available Sprinkler Temperature Ratings Sprinkler Temperature Classification Sprinkler Nominal Temperature Rating Maximum Ambient Ceiling Temperature Temperature Rating of the Cover Plate Assembly Ordinary 162°F (72°C) 100°F (38°C) 140°F (60°C) Intermediate 175°F (79°C) ,150°F(66°C) 140°F (6OC)" Intermediate 175°F (79°C) 150°F (66°C) 162°F (72°C) 1) Maximum ambient temperature for the Cover Plate Assembly is 100°F. (38°C). Precautionary Warnings for Corrosive Environments Model RC-RES sprinklers should not be installed where they may be subjected to a corrosive environment including the following: Chlorine ion and Chloride environment Stress corrosion cracking may be caused by exposure to environments with Chlorine ion and Chloride. Exposure to this environment may result in sprinklers operating under Non-Fire conditions or Not Operating when exposed to an actual fire. Sprinkler system piping with Copper. Sprinkler systems should be constructed in compliance with the applicable standards and the requirements for copper piping when copper piping is used in the sprinkler system. (Reference standards NFPA 13, ASTM B813, B828, and CDA (Copper Development Association) - Solder Joint) All residual flux must be removed from the interior and exterior of the copper piping by thoroughly flushing before installation of the Sprinkler Heads. Otherwise, residues of flux may cause corrosion and/or leakage in the sprinkler system. Document No. U085165 Date : Jan/11/2019 Page :4 of B Hydraulic Design Criteria The minimum required sprinkler flow rates for systems designed to NFPA 13D or 13R are given in TABLE A as a function of temperature rating and the maximum allowable coverage area. The sprinkler flow rate is the minimum required discharge from the most hydraulically demanding sprinkler from each of the total number of "design sprinklers" as specified in. NFPA 130 or 13R. For systems designed to NFPA 13, the number of designed sprinklers is to be the four most hydraulically demanding sprinklers. The minimum required discharge from each of the four sprinklers is to be the greater of the following: The flow rates given in TABLE A for NFPA 13D and 1.3R as a function of temperature rating and maximum allowable coverage area. A minimum discharge of 0.1GPM/sq.ft. [4.07LPM/sq.mj over the "design area" comprised of the four most hydraulically demanding sprinklers for the actual coverage area being protected by the four sprinklers. TABLE A. NFPA 13D & 13R WET PIPE HYDRAULIC DESIGN CRITERIA for Model SS8464 For systems with ceiling types smooth flat horizontal, or beamed, or sloped, in accordance with NFPA 13D, 13R or 13 as applicable. I - Ordinary Intermediate . Maximum Maximum Temperature Rating Temperature Rating Minimum Coverage Area Spacing 162°F (72°C) 175°F (79°C) Deflector Installation Spacing Ft. x Ft. Ft. to Ceiling Type Ft. Flow Pressure Flow Pressure (m xm) (m) GPM PSI GPM PSI (m) (LPM) (bar) (LPM) (bar) 12x12 12 13 7.0 13 7.0 (3.7x3.7) (3.7) (49.2) (0.48) (49.2) (0.48) Smooth Ceilings 1014 14 13 7.0 13 7.0 3/8 to 718 (4.3x4.3) (4.3) (49.2) (0.48) (49.2) (0.48) Inches. Beamed 15x15 15 13 7.0 13 7.0 (4.6x4.6) (4.6) (49.2) (0.48) (49.2) (0.48) Ceilings per NFPA 13D, 13R Concealed 8 (2.4) 16x16 16 13 7.0 14 8.2 or 13 (4.9x4.9) (4.9) (49.2) (0.48) (53.0) (0.57) Installed in beam 3/8 to 7/8 18x18 18 17 12.0 18 13.5 inches (5.5x5.5) (5.5)- (64.3) (0.83) (68.1) (0.93) below - bottom of beam. 20x20 20 21 18.4 (6.14.1) (6.1) (79.5) (1.27) - - For coverage area dimensions less than the above mentioned, it needs to use the minimum required flow for the Next Higher Coverage Area listed. - Requirement is based on minimum flow in GPM (LPM) from each sprinkler. The associated residual pressures are calculated using the nominal K-Factor. Refer to Hydraulic Design Criteria Section for details. Sprinkler Spacing Criteria The minimum spacing between sprinklers is 8 feet (2.4m). The maximum spacing between sprinklers cannot go beyond the coverage area calculated by using the specific hydraulic factors. (Ref. TABLE A) Document No. U085165 Date . Jan/11/2019 Page:50f8 INSTALLATION The Model RC-RES must be installed in accordance with the following instructions: NOTES Do not use any sprinklers which have been subjected to potential mechanical damage. Do not use any sprinklers which show deformation or cracking in either the Sprinkler or the Protective Cap. Prior to installation, sprinklers should be maintained in the original cartons and packaging until used to minimize the potential for damage to the sprinklers that could cause improper operation or non-operation. The Protective Cap must remain on the sprinkler during installation. After the Installation is completed, the Protective Cap must be removed to place the sprinkler in service. Use a torque of 7 to 14 ft•Ibs (9.5 to 19.0 Nm) to achieve a 1/2 inch NPT sprinkler joint. If you exceed the recommended maximum torque, this could result In damage to the sprinkler inlet, which may lead to leakage from the sprinkler. Use only NR-H model wrench socket for installation of RC-RES sprinklers. Use of any other wrench or socket is prohibited and may cause damage to the sprinkler. In case of insufficient adjustment in Cover Plate Installation, do not try to overly tighten, screw the sprinkler too loosely or make any modification to the cover plate assembly., Readjust the sprinkler fitting for a better fit. Do not rotate the Cap Remover RC to the left with force when, placing the two hook arms into place. The Installed sprinkler may become loosened, which may cause water leakage. Installing Procedure Step I The installation requirements for the sprinkler are as follows: to be installed only in the pendent position with the waterway perpendicular to the ceiling. Install the sprinkler fitting so that the distance from the face of the fitting to the mounting surface will be nominally 2 inches (50.8mm) as shown in Figure 3. Step 2 With pipe thread sealant applied to the threads, hand tighten the sprinkler into the sprinkler fitting. Then tighten it with the Socket NR-H or Ratchet (318" drive) & Socket NR-H Combination (Ref. Figure 4). The teeth of the Socket must fit perfectly with the grooves on the Sprinkler for proper Installation (Ref. Figure 4). Step 3 If desired, the Protective Cap may also be used to locate the center of the clearance hole by gently pushing the ceiling material against the center point of the Protective Cap. Before the installation of the ceiling, the sprinkler installation can be started with a 2-318 inch (60mm) diameter clearance hole (Ref. Figure 3). Use the "Vertical Adjustment" indicator on the Protective Cap to check for proper installation height (Ref. Figure 3). Step 4 Use the Cap Remover RC to remove the Protective Cap (Ref. Figure 5), and then push or screw a Cover Plate Assembly on the Cup of the Sprinkler by hand until its flange just has contact with the ceiling (Ref. Figure 6 and Figure 7). Stop tightening the Cover Plate Assembly once the flange has contact with the ceiling If the ceiling has been lifted from its normal position in the process of tightening the Cover Plate Assembly, readjust the cover plate assembly as necessary. If the flange of the Cover Plate Assembly cannot contact the ceiling sufficiently, readjust the sprinkler fitting as necessary. When properly installed, there Is nominal 1116 inch (1.6mm) air gap between the lip of the Cover Plate and the ceiling, as shown in Figure 6. Document No.U085165 Date . Jan/11/2019 or 77 I - \Surface E - rew Def1ectO/ . 4 (tbo$oon)j or 3-1/4" (83mm) or 2-5/8'souare (068mm> IINCQRREthI CORRCT1 IINCORRECTI Document No. U085165 Date : Jan/11/2019 Page :7 o18 CARE AND MAINTENANCE The following instructions must be implemented for the maintenance and service of the Model RC-RES. NOTES Wet pipe sprinkler systems must be maintained at a minimum temperature of 40°F/40C to prevent freezing and bursting of the pipe and/or sprinklers. Automatic sprinklers are not to be tested with a heat source. Operation of the heat respàsive element can result. Absence of a Cover Plate Assembly may delay the response time of the sprinkler In case of a fire. Install the cover plate assembly properly, as shown In Figure 6. Improper installation of the cover platiassembly may cause Improper operation or non-operation. If the ceiling Is to be repainted after the installation of the Sprinkler, care must be exercised to ensure that the new paint does not seal off any of the air gap. Factor,' painted Cover Plates must not be repainted. They should be replaced, If necessary, by factory painted cover plates.. Non-factory applied paint may adversely delay or prevent sprinkler operation in case of a fire. Do not pull the Covr Plate. Separation may result In preparation for maintenance of the fire protection system, permission to close the main control valve must be obtained from the proper authorities, and all affected parties by this action, and must be Informed before the maintenance session can commence. Do NOT enclose any sprinklers within drapes, curtains, or valances. Do NOT hang anything from the sprinklers. Do NOT clean the sprinklers with soap and/or water, detergents, ammonia, cleaning fluids, or other, chemicals. Remove dust, lint cobwebs, cocoons, insects, and larvae by gently brushing with a feather duster or gently vacuuming with a soft bristle (i.e., dusting) brush attachment. - Exercise suitable safety precautions in the use and storage of highly flammable materials. The rapid rate of The development and spread of these materials can reduce the ability of the sprinkler system to aid in the control of a fire Involving such hazards. Leaking or corroded sprinklers must be replaced. Automatic Sprinklers must be kept in a cool and dry place. Automatic sprinklers must never be physically altered, such as painted, plated, or coated, once shipped from the factory. If the sprinklers have been in any way modified, they must be replaced. Great caution must be applied to prevent damage to the sprinklers at all stages - before, during, and after installation. Damaged units because of dropping, hitting, over-tightening, or wrench slippage, must be replaced. The Model RC-RES must only be replaced with pendent sprinklers which are listed for residential fire protection service and which have the same nominal K-Factor, the same coverage area, and the same or lower flow ratings (as indicated under TABLE A "Hydraulic Design Criteria"). When remodeling, such as by adding false beams or light fixtures or changing the location of compartment walls, first verify that the new construction will not violate the installation requirements of the applicable standards of NFPA. Alter the new construction and/or the sprinkler system to suit the requirements of this document and the applicable NFPA regulations. The owner Is responsible for the maintenance of the sprinkler system, including inspection and testing of its compliance with this document, as well as the standards of the National Fire Protection Association (e.g., NFPA 25), and the regulations of any other authorities having Jurisdiction. The owner should direct any questions regarding the above rules and regulations to the Installing contractors or the sprinkler manufacturer. It is recommended that automatic sprinkler systems be Inspected, tested, and maintained by a qualified Inspection Service in accordance with NFPA 25. Document No. U085165 Date : Jan/11/2019 Page 8 of 8 ORDER PROCEDURE When placing an order, please contact a local distributor with the following information (Model Name, Temperature Rating and Finish). Sprinkler Model: RC-RES (SIN: SS8464, Residential Fiat Concealed Sprinkler, Pendent, K4.9, Temperature: 162°F (72°C) or 175°F (79°C)) Cover Plate Assembly, ., 2-5/8 inch (68mm) or 3-1/4 inch (t83mm) or 2-5/8 inch square (068mm), Order Separately from Sprinkler Please refer to the chart below for available sizes, temperature, and finishes. - Standard Finishes Custom Finishes White Ivory Beige Brown Black Nickel Copper Wood Grain Custom Color Custom Pattern 2-5/8° Round, 140°F o a - - - - - - 0 0 3-1/4° Round, 140°F o o o - a o o a a o o 2-5/8" Square, 140°F o - - - - - - - a 2-5/8° Round, 162°F 3-1/4" Round, 162°F Toots for Installation of Model RC-RES Socket NR-H For use with a 3/8" drive ratchet (not included) Socket NR-H Plastic For use with a 1/2" drive ratchet (not included) Cap Remover RC 11 Document No. U085165 Date : Jan/11/2019 tqca Worldwide I Contacts www.tyco-fire.com Series TY-FRB, 56 K-factor Upright, Pendent, and Recessed Pendent Sprinklers Quick Response, Standard Coverage General Description The TYCO Series TY-FRB, 5.6 K-factor, Upright (TY313) and Pendent (TY323) Sprinklers described in this data sheet are quick response, standard coverage, decorative 3 mm glass bulb-type spray sprinklers designed for use in light or ordinary hazard, commercial occupan- cies such as banks, hotels, and shop- ping malls. The recessed version of the Series TY-FRB Pendent Sprinkler, where applicable, is intended for use in areas with a finished ceiling. This recessed pendent sprinkler uses one of the following: A two-piece Style 15 Recessed Escutcheon with recessed adjust- ment up to 5/8 in. (15,9 mm) from the flush pendent position. A two-piece Style 20 Recessed Escutcheon with recessed adjust- ment up to 1/2 in. (12,7 mm) from the flush pendent position. The adjustment provided by the Recessed Escutcheon reduces • the accuracy to which the fixed pipe drops to the sprinklers must be cut. Intermediate level versions of Series TY-FRB Sprinklers are described in Technical Data Sheet 1FP357. Sprin- kler guards and shields are described in Technical Data Sheet TFP780. IMPORTANT Refer to Technical Data Sheet TFP2300 for warnings pertai ning to regulatory and health information. Always refer to Technical Data Sheet TFP700 for the "INSTALLER WARNING" that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and installation can permanently damage a sprinkler system or its compo- nents and cause the sprinkler to fail to operate in a fire situation or cause it to operate prematurely. Page 1 of 4 NOTICE The TYCO Series TY-FRB Sprinklers described herein must be installed and maintained in compliance with this document, as well as with the applicable standards of the National Fire Protection Association, in addition to the standards of any other authori- ties having jurisdiction. Failure to do so may impair the performance of these devices. The owner is responsible for main- taining their fire protection system and devices in proper operating con- dition. Contact the installing contrac- tor or product manufacturer with any questions. Sprinkler Identification. Number (SIN) TY313.... Upright 5.6K, 1/2 in. NPT TV323 .... Pendent 5.6K, 1/2 in. NPT Technical Dätä Approvals Refer to Table A Maximum Working Pressure 175 psi (12.1 bar) 250 psi (17.2 bar)* * The maximum working pressure of 250 psi (17.2 bar) only applies to the listing by Underwriters Laborato-. ries, Inc. (UL). Discharge Coefficient K=5.6 GPM/psl (80,6 LPM/bar) Temperature Rating Refer to Table A Finishes Sprinkler: Refer to Table B Rècéssed Escutcheon: White Coated Black Coated, Chrome Plated, or Brass Plated Physical Characteristics Frame ............................Bronze Button ......................Brass/Copper Sealing Assembly . . . Stainless Steel w/TEFLON Bulb...............................Glass Compression Screw .................Bronze Deflector ..........................Bronze AUGUST 2018 Operation The glass bulb contains a fluid which expands when exposed to heat. When the rated temperature is reached, the fluid expands sufficiently to shatter the glass bulb, allowing the sprinkler to activate and water to flow. Design Criteria The TYCO Series TY-FRB, 5.6 K-factor, Upright (TY313) and Pendent (TY323) Sprinklers are intended for fire protec- tion systems designed in accordance with the standard installation rules recognized by the applicable Listing or Approval agency (such as, UL Listing is based on the requirements of NFPA 13, and FM Approval is based on the requirements of FM's Loss Prevention Data Sheets). Only the Style 15 or Style 20 Recessed Escutcheon is to be used for recessed pendent installations. TFPI72 2-7/8 (73,0 mm) DIA. -. TFPI72 Page 2 of 4 Components: 1 - Frame 2 - Button 3 - Sealing Assembly * Temperature rating is ** Pipe thread connections per ISO 7-1 4 - Bulb indicated on Deflector. can be provided on special request. 5 - Compression Screw ESCUTCHEON PLATE 1/2° 7/16° (11,1 mm) 6 - Deflector* DEFLECTOR* SEATING SURFACE NPT** NOMINAL MAKE-IN 7/16° I (11,1mm) NOMINAL 2 MAKE-IN _____ (50,8 mm) I 2" 1-3/8° (50,8 mm) -- (34,9 mm) WF U" 1/2" NPT** DEFLECTOR* STYLE 15 or 20 RECESSED ESCUTCHEON CROSS SECTION UPRIGHT PENDENT RECESSED PENDENT FIGURE 1 SERIES TY-FRB UPRIGHT (TY313) AND PENDENT (TY323) SPRINKLERS 5.6 K-FACTOR, 1/2 INCH NPT, QUICK RESPONSE WRENCH RECESS e? (USE ONLY END °A) FIGURE 2 W-TYPE 6 SPRINKLER WRENCH WRENCH RECESS f,. PUSH WRENCH IN TO ENSURE ENGAGEMENT WITH SPRINKLER WRENCHING AREA FIGURE 3 W-TYPE 7 RECESSED SPRINKLER WRENCH Installation The TYCO Series TY-FRB, 5.6 K-factor, Upright (TY313) and Pendent (TY323) Sprinklers must be installed in accor- dance with this section. General Instructions Do not Install any bulb-type sprin- kler if the bulb is cracked or there is a loss of liquid from the bulb. With the sprinkler held horizontally, a small air bubble should be present. The diam- eter of the air bubble is approximately 1/16 in. (1,6 mm)forthe 135°F (57°C) and 3/32 in. (2,4 mm) for the 286°F (141°C) temperature ratings. A leak-tight 1/2 in. NPT sprinkler joint should be obtained by applying a minimum to maximum torque of 7 to 14 lb-ft (9,5 to 19,0 N.m). Higher levels of torque can distort the sprinkler Inlet with consequent leakage or impairment of the sprinkler. Do not attempt to compensate for insufficient adjustment in the Escutch- eon Plate by under- or over-tightening the sprinkler. Re-adjust the position of the sprinkler fitting to suit. Upright and Pendent Sprinklers The Series TY-FRB Upright and Pendent Sprinklers must be installed in accordance with the following instructions. Step 1. Install Pendent sprinklers in the pendent position. Install upright sprin- klers in the upright position. Step 2. With pipe-thread sealant applied to the pipe threads, hand- tighten the sprinkler into the sprinkler fitting. Step 3. Tighten the sprinkler into the sprinkler fitting using only the W-Type 6 Sprinkler Wrench (Figure 2). With ref- erence to Figure 1, apply the W-Type 6 Sprinkler Wrench to the wrench flats. Torque sprinklers 7 to 14 lb-ft (9,5 to 19,0 N'm). Recessed Pendent Sprinklers The Series TY-FRB Recessed Pendent Sprinklers must be installed in accor- dance with the following instructions. Step A. After installing the Style 15 or Style 20 Mounting Plate over the sprinkler threads, and with pipe-thread sealant applied to the pipe threads, hand-tighten the sprinkler into the sprinkler fitting. Step B. Tighten the sprinkler into the sprinkler fitting using only the W-Type 7 Recessed Sprinkler Wrench (Figure 3). With reference to Figure 1, apply the W-Type 7 Recessed Sprinkler Wrench to the sprinkler wrench flats. Torque sprinklers 7 to 14 lb-ft (9,5 to 19,0 Nm). Step C. After ceiling installation and finishing, slide on the Style 15 or Style 20 Closure over the Series TY-FRB Sprinkler and push the Closure over the Mounting Plate until its flange comes in contact with the ceiling. TFPI72 Page 3 of 4 Care and Maintenance The TYCO Series TV-FR B, 5.6 K-factor, Upright (TY313) and Pendent (TY323) Sprinklers must be maintained and ser- viced in accordance with this section. Before closing a fire protection system main control valve for maintenance work on the fire protection system that it controls, obtain permission to shut down the affected fire protection systems from the proper authorities and notify all personnel who may be affected by this action. Absence of the outer piece of an escutcheon, which is used to cover a clearance hole, can delay sprinkler operation in a fire situation. The owner must assure that the sprin- klers are not used for hanging any objects and that the sprinklers are only cleaned by means of gently dusting with a feather duster; otherwise, non- operation in the event of a fire or inad- vertent operation may result. Sprinklers which are found to be leaking or exhibiting visible signs of corrosion must be replaced. Automatic sprinklers must never be painted, plated, coated, or other- wise altered after leaving the factory. Modified sprinklers must be replaced. Sprinklers that have been exposed to corrosive products of combustion, but have not operated, should be replaced if they cannot be completely cleaned by wiping the sprinkler with a cloth or by brushing it with a soft bristle brush. Care must be exercised to avoid damage to the sprinklers before, during, and after installation. Sprin- klers damaged by dropping, striking, wrench twist/slippage, or the like, must be replaced. Also, replace any sprin- kler that has a cracked bulb or that has lost liquid from its bulb. (Ref. Installa- tion Section.) The owner is responsible-for the inspection, testing, and maintenance of their fire protection system and devices in compliance with this document, as well as with the applicable standards of the National Fire Protection Asso- ciation (e.g., NFPA 25), in addition to the standards of any other authorities having jurisdiction. Contact the install- ing contractor or product manufacturer with any questions. Automatic sprinkler systems are rec- ommended to be inspected, tested, and maintained by a qualified Inspec- tion Service in accordance with local requirements and/or national codes. Limited Warranty For warranty terms and conditions, visit www.tyco-fire.com. Ordering Procedure Contact your local distributor for avail- ability. When placing an order, indicate the full product name and Part Number (P/N). Sprinkler Assemblies with NPT Thread Connections Specify: Series TY-FRB Upright or Pendent (specify) Sprinkler, SIN (specify), K=5.6, Quick Response, (specify) temperature rating, (specify) finish, P/N (specify, refer to Table A). Recessed Escutcheon Specify: Style 15 Recessed Escutch- eon with (specify*) finish, P/N (specify*) Specify: Style 20 Recessed Escutch- eon with (specify*) finish, P/N (specify*) "Refer to Technical Data Sheet TFP770 Sprinkler Wrench Specify: W-Type 6 Sprinkler Wrench, P/N 56-000-6-387 Specify: W-Type 7 Sprinkler Wrench, P/N 56-850-4-001 - 2-7/8° DIA. (73,0 mm) 2-1/4° DIA. FACE OF (57,2 mm) 5/8(15,9mm) SPRINKLER FITTING 3/8±5/16 I (9,5±7,9 mm) FLUSH MOUNTING 1/8" SURFACE —__(3,2 mm) CLOSURE SERIES MOUNTING 1-3/8 (34,9 mm) TYFRB PLATE 3/4" (19,1 mm) FIGURE 4 SERIES TY-FRB RECESSED PENDENT SPRINKLER ASSEMBLY (TY323) WITH TWO PIECE 5/8 INCH TOTAL ADJUSTMENT STYLE 15 RECESSED ESCUTCHEON 2-7/8" DIA. (73,0 mm) FACE OF SPRINKLER 2-1/4° DIA. 1/2" (12,7 mm) 5/16±1/4° \ #(3,2 FIlliNG (57,2 mm) (7,9*6,4 mm) FLUSH 717, MOUNTING SURFACE m) CLOSURE SERIES MOUNTING 1-3/8° (34,9 mm) TV-FRB PLATE 7/8" (22,2 mm) FIGURE 5 SERIES TY-FRB RECESSED PENDENT SPRINKLER ASSEMBLY (TY323) WITH TWO PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 20 RECESSED ESCUTCHEON TFPI72 Page 4 of 4 SPRINKLER FINISH (See Note 7) K FACTOR TYPE TEMPERATURE BULB UQUID COLOR NATURAL BRASS I CHROME PLATED I POLYESTER- 135°F(570C) Orange UPRIGHT (1Y313) 155°F(68°C) Red 175°F (79°C) Yellow and 1i 2, 3,4, 5,.6 5.6 1/2 in. NPT PENDENT (TY323) ________________ 200°F (93°C) Green 286°F (141°C) Blue 135°F (57°C) Orange RECESSED PENDENT (1Y323) Figures 45 and 5b 1, 2,3,4 55°F (68°C) Red 75°F (790C) r2,00-F Yellow (93°C) Green Notes: Listed by Underwriters Laboratories, Inc., (UL) as Quick Response Sprinklers. Listed by Underwriters Laboratories, Inc., for use in Canada (C-UL) as Quick Response Sprinklers. Approved by Factory Mutual Research Corporation (FM) as Quick Response Sprinklers. Approved by the City of New York under MEA 354-01-E. VdS Approved (For details, contact Johnson Controls, Enschede, Netherlands, Tel. 31-53-428-44.44/Fax 31-54-428-3377.) Approved by the Loss Prevention Certification Board (LPCB Ref. No. 094aJ06) as Quick Response Sprinklers. Where Polyester Coated Sprinklers are noted to be UL and C-Ut. Listed, the sprinklers are UL and C-UL Listed as Corrosion-Resistant Sprinklers. Installed with Style 15(1/2 in. NPT) 5/8 in. Total Adjustment Recessed Escutcheon, as applicable. Installed with Style 20(1/2 in. NPT) 1/2 In. Total Adjustment Recessed Escutcheon, as applicable. C. Frame and Deflector only. Listings and approvals apply to color (Special Order). TABLEA LABORATORY LISTINGS AND APPROVALS FOR 5.6 K-FACTOR SPRINKLERS P/Na77_X)X__XXX_________ F SPRINKLER TEMPERATURE S N FINISH RATINGS I 370 I 5.6K UPRIGHT (1/2 in.NPT) I TY313 I 371 1 5.6K PENDENT (1/2 in.NPT) 1Y323 Notes: a. Use suffix "I" for ISO 7-1 connection: for example, 77-370-4-175-I 1 I NATURAL BRASS PURE WHITE (RAL9010)a POLYESTER SIGNAL WHITE (RAL9003) POLYESTER JET BLACK (RAL9005) POLYESTER 9 I CHROME PLATED 135 135-F (57-C) 155 155-F (68-C) 175 175-F (79-C) 200 200°F (93°C) 286 286-F (141-C) Notes: a. Eastern Hemisphere sales only TABLE B SERIES TY-FRB UPRIGHT AND PENDENT SPRINKLERS PART NUMBER SELECTION 1400 Pennbrook Parkway, Lansdale, PA 194461 Telephone +1-215-362-0700 02018 Joh,,o,, Controls. AR rieht. re,wvod. *11 o8I.tin..nd oth b,fon,,e80,, .how,, --t -.f d o,o.droloIon d.t.nd or. .obl.ol to 0..gvwftWA ootioo, Johnson Controls TEFL.ONI 0 098to,odt,udwwl,olooPwt