HomeMy WebLinkAbout1896 RUTHERFORD RD; ; AS060288; Permit10/27/21, 10:24 AM AS060288 Permit Data
City of Carlsbad
Sprinkler Permit
1896 RUTHERFORD
Job Address:
RD
Permit Type: SPRINK
Parcel No: 2121203000
Lot #: 0
Reference No.:
Permit No: AS060288
Status: ISSUED
Applied 11/29/2006
Approved: 12/5/2006
Issued: 12/5/2006
PC #: Inspector:
Project Title: ISIS INSTRUMENT LAB TI FIRE SPRINKLER PLAN CHECK &
INSPECTIONS
Applicant:
COSCO FIRE PROTECTION
10695 TREENA ST
SAN DIEGO, CA
858-444-2000
Owner:
P D G CARLSBAD 46 LTD
4330 LA JOLLA VILLAGE DR #110
SAN DIEGO CA
r Fees ($) J Add'I Fees ($) Total ($) Balance ($)
L 124 0 124 0
1/1
March 5, 2004 Sprinkler 10 a
1. PRODUCT NAME
Viking CCCF Approved Standard Re-
sponse Pendent Sprinkler Part Number
12727F8
Available since 2004.
2. MANUFACTURER
The Viking Corporation
210 N. Industrial Park Road
Hastings, Michigan 49058 U.S.A.
Telephone: (269) 945-9501
(877) 384-5464
Fax: (269) 945-9599
e-mail: techsvcs@vikingcorp.com
3. PRODUCT DESCRIPTION
Viking CCCF Approved Standard Re-
sponse Sprinkler Part Number 12727 is a
small thermosensitive spray sprinkler
available with a 155 °F temperature rat-
ing and chrome finish. The small frame
and 5 mm glass bulb provide a pleasing
appearance.
During fire conditions, the heat-sensi-
tive liquid in the glass bulb expands,
causing the bulb to shatter, releasing the
pip cap and sealing spring assembly.
Water flowing through the sprinkler ori-
fice strikes the sprinkler deflector, form-
ing a uniform spray pattern to extinguish
or control the fire.
4. TECHNICAL DATA
APPROVALS
Approved by the China Certification
Center for Fire Products (CCCF),
standard GB5135-1993.
Refer to the chart on page 10 b.
Spacing Requirements: Maximum
spacing 15 ft. (4,6 m). Minimum spac-
ing 6 ft. (1,8 m).
Glass bulb fluid temperature rated to
-65°F (-55 °C).
Minimum Operating Pressure: 7 psi
(48,3 kPa).
Rated to 175 psi (1 207kPa)waterwork-
ing pressure.
Factory tested hydrostatically to 500 psi
(3 448 kPa).
SPRINKLER MATERIALS
Frame: Brass Castings UNS-C84400
Deflector: Brass UNS-051000 or Cop-
per UNS-C19500
Bulb: Glass, nominal 5 mm diameter
Belleville Spring Sealing Assembly:
Nickel Alloy, coated on both sides
with Teflon Tape
Screw: Brass UNS-C36000
Pip Cap and Insert Assembly: Copper
UNS-C11000 and Stainless Steel
UNS-S30400
AVAILABLE FINISH
Chrome-Enloy5 (patents pending)
ACCESSORIES
Sprinkler Wrenches:
Standard wrench: Part Number
10896W/B (available since 2000) or
05000CW/B (no longer available).
Wrench for recessed Standard Re-
sponse Sprinklers: Part
Number 07398W** (available since
1990), or Part Number 12144W/B**,
available since 2003. NOTE: Re-
cessed pendent sprinklers with
protective caps must use wrench
12144W/B.
°A %" ratchet is required (not available from Vi-
king).
Refer to the "Sprinkler Accessories"
section of the data book.
5. AVAILABILITY AND SERVICE
Viking products are available through a
network of domestic, Canadian, and
international distributors. See the Viking
Corp. Web site for your closest distribu-
tor or contact The Viking Corporation.
Viking technical data may be found on
The Viking Corporation's Web site at
http://www.vikingcorp.com.
The Web site may include a more recent
edition of this technical data page.
Sprinkler 12727FB with a
standard 1/8" (3,1 mm)
surface-mounted escutcheon
Ceiling Opening Size: 2-5/16' (59 mm) Minimum,
2-1/2" (64 mm) Maximum. 2-1/8- 2 1/8 (54 mm)-
...............
(54 mm)
mm)
(51 2 1-1/2" (38 mrn) 17-3/4- um
Minimum (44,5 mm) Minimum
J_ Maximum
Sprinkler 12727FB
Sprinkler 12727FB
installed with a Microfast®
Model F-i Adjustable Escutcheon.
Figure 1
Sprinkler 12727FB
installed with a Micromatic®
Model E-1 Recessed Escutcheon.
Note: Units of measure in parentheses maybe approximations. New page 10 a-b, dated March 5, 2004. Refer to technical data
Form No. F061303 page SRI-2 for general care, installation, and maintenance
- information.
Sprinkler 10 b March 5, 2004
CCCF APPROVED
STANDARD RESPONSE j IIJI1G®- I II[.U'7If_ 't SPRINKLER
(Part Number 12727FB)
Approval Chart4 Temperature KEY
Finish CCCF Approved Standard Response
Pendent Sprinkler 12727FB AIX+- Escutcheon (if applicable)
Maximum WWP _175_PSI
Thread
Size
Nominal
K-Factor Overall Length I Temperature
classification
Nominal Temp.
Rating (Fusing Point)
Maximum Ambient
Ceiling Temperature'
Bulb
Color
CCCF
Approva12 NPT1BSPU I I S. metric5 Inch mm
1/2' 15 mm 5.6 8,1 2-3/16 I 56 Ordinary 155°F (68 °C) 100°F (38 °C) Red AiX
Approved Escutcheons3 Approved Temperature Rating Approved Finish x - Standard surface-mounted escutcheons orthe Microfast® Model F-i Adjustable
A - 155 °F(68 °C) 1 - Chrome-Enloy® Escutcheon, or recessed with the Micromatic® Model E-1 Recessed Escutch-
eon
Footnotes
1 Based on NFPA-1 3. Other limits may apply, depending on fire loading, sprinkler location, and other requirements of the Authority Having Jurisdiction.
Refer to specific installation standards.
2Approved, China Certification Center for Fire Products (CCCF), standard GB5135-1993.
Refer to the "Sprinkler Accessories" section for technical data on approved escutcheons and other accessories. Escutcheons must be ordered
separately from sprinklers. Refer to Viking's current price schedule.
This table shows the listings and approvals available at the time of printing.
5Metnc K-factorshown is for usewhen pressure is measured in kPa. When pressure is measured in BAR, multiply the metric K-factor shown by 10.0.
Spacing Requirements: Maximum spacing 15 ft. (4,6 m), minimum spacing 6 ft. (1,8 m).
New page 10 a-b, dated March 5, 2004. Refer to technical data page SRI-2 for Form No. F_061303
general care, installation, and maintenance information.
March 5, 2004 Sprinkler 10 a
1. PRODUCT NAME
Viking CCCF Approved Standard Re-
sponse Pendent Sprinkler Part Number
12727FB
Available since 2004.
2. MANUFACTURER
The Viking Corporation
210 N. Industrial Park Road
Hastings, Michigan 49058 U.S.A.
Telephone: (269) 945-9501
(877) 384-5464
Fax: (269) 945-9599
e-mail: techsvcsvikingcorp.com
3. PRODUCT DESCRIPTION
Viking CCCF Approved Standard Re-
sponse Sprinkler Part Number 12727 is a
small thermosensitive spray sprinkler
available with a 155 °F temperature rat-
ing and chrome finish. The small frame
and 5 mm glass bulb provide a pleasing
appearance.
During fire conditions, the heat-sensi-
tive liquid in the glass bulb expands,
causing the bulb to shatter, releasing the
pip cap and sealing spring assembly.
Water flowing through the sprinkler ori-
fice strikes the sprinkler deflector, form-
ing a uniform spray pattern to extinguish
or control the fire.
4. TECHNICAL DATA
APPROVALS
Approved by the China Certification
Center for Fire Products (CCCF),
standard GB5135-1993.
Refer to the chart on page 10 b.
Spacing Requirements: Maximum
spacing 15 ft. (4,6 m). Minimum spac-
ing 6 ft. (1,8 m).
Glass bulb fluid temperature rated to
-65°F (-55 °C).
Minimum Operating Pressure: 7 psi
(48,3 kPa).
Rated to 175 psi (1 207 kPa) water work-
ing pressure.
Factory tested hydrostatically to 500 psi
(3 448 kPa).
SPRINKLER MATERIALS
Frame: Brass Castings UNS-C84400
Deflector: Brass UNS-051000 or Cop-
per UNS-C19500
Bulb: Glass, nominal 5 mm diameter
Belleville Spring Sealing Assembly:
Nickel Alloy, coated on both sides
with Teflon Tape
Screw: Brass UNS-C36000
Pip Cap and Insert Assembly: Copper
UNS-C1 1000 and Stainless Steel
UNS-S30400
AVAILABLE FINISH
Chrome-Enloy (patents pending)
ACCESSORIES
Sprinkler Wrenches:
Standard wrench: Part Number
10896W/B (available since 2000) or
05000CWIB (no longer available).
Wrench for recessed Standard Re-
sponse Sprinklers: Part
Number 07398W** (available since
1990), or Part Number 12144W/B**,
available since 2003. NOTE: Re-
cessed pendent sprinklers with
protective caps must use wrench
12144W1B.
°°A W ratchet is required (not available from Vi-
king).
Refer to the "Sprinkler Accessories"
section of the data book.
5. AVAILABILITY AND SERVICE
Viking products are available through a
network of domestic, Canadian, and
international distributors. See the Viking
Corp. Web site for your closest distribu-
tor or contact The Viking Corporation.
Viking technical data may be found on
The Viking Corporation's Web site at
hftp:/Iwww.vikingcorp.com.
The Web site may include a more recent
edition of this technical data page.
Sprinkler 12727FB with a
standard 1/8" (3,1 mm)
surface-mounted escutcheon.
Ceiling Opening Size: 2-5/16" (59 mm) Minimum,
2-1/2" (64 mm) Maximum. 2-1/8- 2 1/8
(54 mm)—
.........
(54 mm)
MEM
Maximum* Maximum
mm)
Sprinkler 12727FB
Sprinkler 12727FB
installed with a Microfast®
Model F-i Adjustable Escutcheon.
Figure 1
Sprinkler 12727FB
installed with a Micromatid
Model E-i Recessed Escutcheon.
Note: Units of measure in parentheses maybe approximations. New page 10 a-b, dated March 5, 2004. Refer to technical data
Form No. F 061303 page SRI-2 for general care, installation, and maintenance
- information.
Sprinkler 10 March 5, 2004
CCCF APPROVED
STANDARD RESPONSE SPRINKLER
(Part Number 12727F21
Approval Chart4 Temperature KEY
Finish CCCF =d Standard Res
Pendent Sprinkler 12727F Al X4— Escutcheon (if applicable)
Maximum PSI _175_ _WWP
Thread
Size
Nominal
K-Factor Overall Length Temperature
Classification
Nominal Temp.
Rating (Fusing Point)
Maximum Ambient
Ceiling Temperature 1
Bulb
Color
CCCF
Approval2 NPT I BSPU S. metric5 Inch I mm
h/2 15mm 5.6 1 8,1 2-3/16 1 56 Ordinary 155°F (68 °C) 100°F (38 °C) Red AiX
Approved Escutcheons3 Approved Temperature Rating Approved Finish x - Standard surface-mounted escutcheons orthe Microfast® Model F-i Adjustable A - 155°F (68 °C) 1 - Chrome-Enloy® Escutcheon, or recessed with the Micromatic Model E-i Recessed Escutch-
eon
Footnotes
Based on NFPA-13. Other limits may apply, depending on fire loading, sprinkler location, and other requirements of the Authority Having Jurisdiction. Refer to specific installation standards.
2Approved, China Certification Center for Fire Products (CCCF), standard GB5135-1993.
Refer to the "Sprinkler Accessories" section for technical data on approved escutcheons and other accessories. Escutcheons must be ordered
separately from sprinklers. Refer to Viking's current price schedule.
This table shows the listings and approvals available at the time of printing.
5Metnc K-factor shown is for use when pressure is measured in kPa. When pressure is measured in BAR, multiply the metric K-factor shown by 10.0.
Spacing Requirements: Maximum spacing 15 ft. (4,6 m), minimum spacing 6 ft. (1,8 m).
New page 10 a-b, dated March 5, 2004. Refer to technical data page SRI-2 for Form No. F 061303
general care, installation, and maintenance information.
March 5, 2004 Sprinkler 10 a
1. PRODUCT NAME
Viking CCCF Approved Standard Re-
sponse Pendent Sprinkler Part Number
12727FB
Available since 2004.
2. MANUFACTURER
The Viking Corporation
210 N. Industrial Park Road
Hastings, Michigan 49058 U.S.A.
Telephone: (269) 945-9501
(877) 384-5464
Fax: (269) 945-9599
e-mail: techsvcs@vikingcorp.com
3. PRODUCT DESCRIPTION
Viking CCCF Approved Standard Re-
sponse Sprinkler Part Number 12727 is a
small thermosensitive spray sprinkler
available with a 155 °F temperature rat-
ing and chrome finish. The small frame
and 5 mm glass bulb provide a pleasing
appearance
During fire conditions, the heat-sensi-
tive liquid in the glass bulb expands,
causing the bulb to shatter, releasing the
pip cap and sealing spring assembly.
Water flowing through the sprinkler ori-
fice strikes the sprinkler deflector, form-
ing a uniform spray pattern to extinguish
or control the fire.
4. TECHNICAL DATA
APPROVALS
Approved by the China Certification
Center for Fire Products (CCCF),
standard GB5135-1993.
Refer to the chart on page 10 b.
Spacing Requirements: Maximum
spacing 15 ft. (4,6 m). Minimum spac-
ing 6 ft. (1,8 m).
Glass bulb fluid temperature rated to
-65 ¶ (-55 °C).
Minimum Operating Pressure: 7 psi
(48,3 kPa).
Rated to 175 psi (1 207 kPa) water work-
ing pressure.
Factory tested hydrostatically to 500 psi
(3 448 kPa).
SPRINKLER MATERIALS
Frame: Brass Castings UNS-C84400
Deflector: Brass UNS-051000 or Cop-
per UNS-C19500
Bulb: Glass, nominal 5 mm diameter
Belleville Spring Sealing Assembly:
Nickel Alloy, coated on both sides
with Teflon Tape
Screw: Brass UNS-C36000
Pip Cap and Insert Assembly: Copper
UNS-C1 1000 and Stainless Steel
UNS-530400
AVAILABLE FINISH
Chrome-EnIoy (patents pending)
ACCESSORIES
Sprinkler Wrenches:
Standard wrench: Part Number
10896W/B (available since 2000) or
05000CW/B (no longer available).
Wrench for recessed Standard Re-
sponse Sprinklers: Part
Number 07398W** (available since
1990), or Part Number 12144W/B**,
available since 2003. NOTE: Re-
cessed pendent sprinklers with
protective caps must use wrench
12144W/B.
"A W ratchet is required (not available from Vi- king).
Refer to the "Sprinkler Accessories"
section of the data book.
5. AVAILABILITY AND SERVICE
Viking products are available through a
network of domestic, Canadian, and
international distributors. See the Viking
Corp. Web site for your closest distribu-
tor or contact The Viking Corporation.
Viking technical data may be found on
The Viking Corporation's Web site at
http://www.vikingcorp.com.
The Web site may include a more recent
edition of this technical data page.
Sprinkler 12727FB with a
standard 1/8" (3,1 mm)
surface-mounted escutcheon.
Ceiling Opening Size: 2-5/16" (59 mm) Minimum,
2-1/2" (64 mm) Maximum. 2-1/8- 2 1/8 (54 mm)-
...
(54 mm)
mm)
Maximum* Maximum
Sprinkler 12727FB
Sprinkler 12727FB Sprinkler 12727FB
installed with a Microfast® installed with a Micromati®
Model F-i Adjustable Escutcheon. Model E-i Recessed Escutcheon.
Note: Units of measure in parentheses maybe approximations. New page 10 a-b, dated March 5, 2004. Refer to technical data
Form No. F_061303 page SRI-2 for general care, installation, and maintenance
information.
Sprinkler 10 b March 5, 2004
CCCF APPROVED
A A A STANDARD RESPONSE
N11a SPRINKLER
Part Number 12727FB
Approval Chart4 I Temperature KEY
Finish CCCF Approved Standard Response
Pendent Sprinkler 12727FB AIX+- Escutcheon (if applicable)
Maximum PSI _175_ _WWP
Thread
Size
Nominal
K-Factor
I Overall Length Temperature
Classification
I Nominal Temp. I Rating (Fusing Point)
Maximum Ambient
I Ceiling Temperature 1 I I I
Bulb
Color
I CCCF
Approva12
I NPT I BSPU S. metrics Inch mm
15mm 5.6 8,1 2-3/16 I 56 Ordinary I 155°F (68 °C) I 100°F (38 °C) I Red AiX
Approved Escutcheons3 Approved Temperature Rating Approved Finish X -Standard surface-mounted escutcheons ore Microfast® Model F-i Adjustable A - 155°F (68 °C) 1 - Chrome-Enloy5 Escutcheon, or recessed with the Micromatic Model E-1 Recessed Escutch-
eon
Footnotes
1 Based on NFPA-1 3. Other limits may apply, depending on fire loading, sprinkler location, and other requirements of the Authority Having Jurisdiction. Refer to specific installation standards.
2Approved, China Certification Center for Fire Products (CCCF), standard GB5135-1993.
Refer to the "Sprinkler Accessories" section for technical data on approved escutcheons and other accessories. Escutcheons must be ordered sprinklers. current price schedule. separately from Refer to Vikings 4 This table shows the listings and approvals available at the time of printing.
5Metnc K-factor shown is for use when pressure is measured in kPa. When pressure is measured in BAR, multiply the metric K-factor shown by 10.0.
Spacing Requirements: Maximum spacing 15 ft. (4,6 m), minimum spacing 6 ft. (1,8 m).
New page 10 a-b, dated March 5, 2004. Refer to technical data page SRI-2 for Form No. F_061303
general care, installation, and maintenance information.
Sprinkler 12727FB
March 5, 2004 Sprinkler 10 a
1. PRODUCT NAME
Viking CCCF Approved Standard Re-
sponse Pendent Sprinkler Part Number
12727FB
Available since 2004.
2. MANUFACTURER
The Viking Corporation
210 N. Industrial Park Road
Hastings, Michigan 49058 U.S.A.
Telephone: (269) 945-9501
(877) 384-5464
Fax: (269) 945-9599
e-mail: techsvcs@vikingcorp.com
3. PRODUCT DESCRIPTION
Viking CCCF Approved Standard Re-
sponse Sprinkler Part Number 12727 is a
small thermosensitive spray sprinkler
available with a 155 "F temperature rat-
ing and chrome finish. The small frame
and 5 mm glass bulb provide a pleasing
appearance.
During fire conditions, the heat-sensi-
tive liquid in the glass bulb expands,
causing the bulb to shatter, releasing the
pip cap and sealing spring assembly.
Water flowing through the sprinkler ori-
fice strikes the sprinkler deflector, form-
ing a uniform spray pattern to extinguish
or control the fire.
4. TECHNICAL DATA
APPROVALS
Approved by the China Certification
Center for Fire Products (CCCF),
standard G85135-1993.
Refer to the chart on page 10 b.
Spacing Requirements: Maximum
spacing 15 ft. (4,6 m). Minimum spac-
ing 6 ft. (1,8 m).
Glass bulb fluid temperature rated to
-65 "F (-55 "C).
Minimum Operating Pressure: 7 psi
(48,3 kPa).
Rated to 175 psi (1 207 kPa) water work-
ing pressure.
Factory tested hydrostatically to 500 psi
(3 448 kPa).
SPRINKLER MATERIALS
Frame: Brass Castings UNS-C84400
Deflector: Brass UNS-051000 or Cop-
per UNS-C 19500
Bulb: Glass, nominal 5 mm diameter
Belleville Spring Sealing Assembly:
Nickel Alloy, coated on both sides
with Teflon Tape
Screw: Brass UNS-C36000
Pip Cap and Insert Assembly: Copper
UNS-C11000 and Stainless Steel
UNS-530400
AVAILABLE FINISH
Chrome-Enloy' (patents pending)
ACCESSORIES
Sprinkler Wrenches:
Standard wrench: Part Number
10896W/B (available since 2000) or
05000CWIB (no longer available).
Wrench for recessed Standard Re-
sponse Sprinklers: Part
Number 07398Wk* (available since
1990), or Part Number 12144W/B**,
available since 2003. NOTE: Re-
cessed pendent sprinklers with
protective caps must use wrench
121 44W/B. ""A %" ratchet is required (not available from Vi-
king).
Refer to the "Sprinkler Accessories"
section of the data book.
5. AVAILABILITY AND SERVICE
Viking products are available through a
network of domestic, Canadian, and
international distributors. See the Viking
Corp. Web site for your closest distribu-
tor or contact The Viking Corporation.
Viking technical data may be found on
The Viking Corporation's Web site at
http://www.vikingcorp.com.
The Web site may include a more recent
edition of this technical data page.
Ceiling Opening Size: 2-5/16" (59 mm) Minimum,
2-1/2" (64 mm) Maximum. Sprinkler 12727FB with a
standard 1/8" (3,1 mm)
surface-mounted escutcheon 2-1/8"
(54 mm)
mom
2" 1-1/2" (.38 Minimum
Sprinkler 12727FB
installed with a Microfast®
Model F-i Adjustable Escutcheon.
Sprinkler 12727FB
installed with a Micromatid5
Model E-1 Recessed Escutcheon.
Figure 1 I
Note: Units of measure in parentheses maybe approximations. New page 10 a-b, dated March 5, 2004. Refer to technical data
Form No. F 061303 page SRI-2 for general care, installation, and maintenance
- information.
Sprinkler 10 March 5, 2004
CCCF APPROVED
ST N41 KJ STANDARD RESPONSE
SPRINKLER
(Part Number 12727FB)
Approval Chart4 Temperature KEY
I - Finish CCCF Approved Standard Response Pendent Sprinkler 12727FB Al X*— Escutcheon (if applicable)
Maximum 175 PSI WWP
Thread
Size
Nominal
I K-Factor Overall Length Temperature
Classification I
Nominal Temp.
i Rating (Fusing Point) I
Maximum Ambient
I Ceiling Temperature'
Bulb
Color
CCCF
I Approva12 I NPT T BSPUI S. I metric5 I In I mm
15mm 5.6 8,1 2-3/16 1 56 I Ordinary 155°F (68 °C) I 100 °F (38 °C) I Red I AiX
Approved Escutcheons3 Approved Temperature Rating Approved Finish X - Standard surface-mounted escutcheons ore Microfast® Model F-i Adjustable A - 155 °F (68 °C) 1 - Chrome-Enloy® I Escutcheon, or recessed with the Micromatic Model E-1 Recessed Escutch-
eon
Footnotes
Based on NFPA-13. Other limits may apply, depending on fire loading, sprinkler location, and other requirements of the Authority Having Jurisdiction. Refer to specific installation standards.
2Approved China Certification Center for Fire Products (CCCF), standard G135135-1993.
Refer to the "Sprinkler Accessories" section for technical data on approved escutcheons and other accessories. Escutcheons must be ordered separately from sprinklers. Refer to Viking's current price schedule.
This table shows the listings and approvals available at the time of printing.
5Metnc K-factor shown is for use when pressure is measured in kPa. When pressure is measured in BAR, multiply the metric K-factor shown by 10.0.
Spacing Requirements: Maximum spacing 15 ft. (4,6 m), minimum spacing 6 ft. (1,8 m).
New page 10 a-b, dated March 5, 2004. Refer to technical data page SRI-2 for Form No. F_061303
general care, installation, and maintenance information.