Loading...
HomeMy WebLinkAbout2175 SALK AVE; 200; AS110165; PermitCity of Carlsbad Sprinkler Permit Permit No: AS110165 Job Address: 2175 SALK AV Permit Type: SPRINK Parcel No: 2120210800 Lot #: 0 Reference No.: PC #: Status: ISSUED Applied 11/1/2011 Approved: Issued: Inspector: Project Title: ALTIUM-STE 200 T.I. Applicant: PARAMOUNT FIRE SYSTEMS, INC. P.O. BOX 713194 SANTEE, CA 619-562-6247 Owner: RIO SD PLAZA II MASTER LLC C/O NEWPORT NATIONAL CORPORATION 1525 FARADAY AVE #100 CARLSBAD CA Fees ($) Add'I Fees ($) Total ($) Balance ($) 262 0 262 0 A8110146 tqco /Fire & Building / Products Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500 Series TY-B - 2.8, 5.6, and 8.0 K-factor Upright, Pendent, and Recessed Pendent Sprinklers Standard Response, Standard Coverage General Description The Series TY-B, 2.8, 5.6, and 8.0 K-factor, Upright and Pendent Sprin- klers described in this data sheet are standard response - standard cover- age, decorative 5 mm glass bulb type spray sprinklers designed for use in light, ordinary, or extra hazard, com- mercial occupancies such as banks, hotels, shopping malls, factories, refin- eries, chemical plants, etc. The recessed version of the Series TY-B Pendent Sprinkler, where appli- cable, is intended for use in areas with a finished ceiling. It uses a two-piece Style 10 (1/2 inch NPT) or Style 40(3/4 inch NPT) Recessed Escutcheon. The Recessed Escutcheon provides 1/2 inch (12,7 mm) of recessed adjust- ment or up to 3/4 inch (19,1 mm) of total adjustment from the flush pen- dent position. The adjustment pro- vided by the Recessed Escutcheon re- duces the accuracy to which the fixed pipe drops to the sprinklers must be cut. Corrosion resistant coatings, where applicable, are utilized to extend the life of copper alloy sprinklers beyond that which would otherwise be ob- tained when exposed to corrosive at- mospheres. Although corrosion resis- tant coated sprinklers have passed the standard corrosion tests of the appli- IMPORTANT Always refer to Technical Data Sheet TFP700 for the "INSTALLER WARNING" that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and in- stallation can permanently damage a sprinkler system or its compo- nents and cause the sprinkler to fall to operate in a fire situation or cause it to operate prematurely. cable approval agencies, the testing is not representative of all possible cor- rosive atmospheres. Consequently, it is recommended that the end user be consulted with respect to the suitability of these coatings for any given corro- sive environment. The effects of ambi- ent temperature, concentration of chemicals, and gas/chemical velocity, should be considered, as a minimum, along with the corrosive nature of the chemical to which the sprinklers will be exposed. An intermediate level version of the Series TY-B Pendent Sprinkler can be obtained by utilizing the Series TV-B Pendent Sprinkler in combination with the Model S2 Shield. WARNINGS The Series TY-B Sprinklers described herein must be installed and main- tained in compliance with this docu- ment, as well as with the applicable standards of the National Fire Protec- tion Association, in addition to the standards of any other authorities hav- ing jurisdiction. Failure to do so may impair the performance of these de- vices. The owner is responsible for maintain- ing their fire protection system and de- vices in proper operating condition. The installing contractor or sprinkler manufacturer should be contacted with any questions. Model/Sprinkler Identification Numbers TYII5I - Upright 2.81K, 1/2"NPT 1Y1251 - Pendent 2.81K, 1/2"NPT TY3151 - Upright 5.6K, 1/2"NPT TY3251 - Pendent 5.6K, 1/2"NPT TY4151 - Upright 8.0K, 314"NPT TY4251 - Pendent 8.0K, 3/4'NPT TY4851 - Upright 8.0K, 1/2"NPT TY4951 - Pendent 8.0K, 1/2"NPT - ALUM Pagel of 8 DECEMBER, 2007 TFPI5I SSU * DEFLECTOR Page 2 of 8 TFPI5I ESCUTCHEON PLATE SEATING SURFACE -r- 2-1/4" (57,2 mm) 1-9/16 (39,7 m 7/16' (11,1 mm) ** NOMINAL 1/2,, MAKE-IN NPT J fRENCH FLATS 55p * DEFLECTOR CROSS SECTION PENDENT UPRIGHT 1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to 2 - Button Assembly 5 - Compression 7 - Bushing orifice seat on frame. Screw **Pipe thread connections per ISO 7/1 can be provided on special request. FIGURE 1 STANDARD RESPONSE SERIES TY-B UPRIGHT (TYII5I) AND PENDENT (TY1251) SPRINKLERS 2.8 K-FACTOR, 1/2 INCH NPT STYLE 10 RECESSED SSU* ESCUTCHEON DEFLECTOR (11,1 mm) ZNOMINAL 7/16" MAKE-IN WRENCH MAK 2-3/16" FLATS NPT** (55,6 mm) 1/2" ESCUTCHEON PLATE SEATING SURFACE _F_ 2-3/16" (55,6 mm) T 7/16(11,1 mm) 1/2" ** NOMINAL MAKE-IN NPT SSP DEFLECTOR* 2-7/8" (73,0 mm) DIA. PENDENT RECESSED PENDENT UPRIGHT CROSS SECTION 1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to 2 - Button Assembly 5 - Compression orifice seat on frame. Screw **Pipe thread connections per ISO 7/1 can be provided on special request. FIGURE 2 STANDARD RESPONSE SERIES TY-B UPRIGHT (TY3151) AND PENDENT (TY3251) SPRINKLERS 5.6 K-FACTOR, 112 INCH NPT 11 A TFPI5I ESCUTCHEON 1/2(12,7mm) STYLE 40 PLATE SEATING ** NOMINAL RECESSED SURFACE 3/4" MAKE-IN ESCUTCHEON NPT 2-5/16' (58,7 mm) f 17 I I-U/10 I (39,7 mm) WRENCH FLATS SSP DEFLECTOR* 2-718 (73,0 mm) DIA. PENDENT RECESSED PENDENT Page 3 of 8 SSU * DEFLECTOR 1/2" I (12,7 mm) I NOMINAL I MAKE-IN 2-1/4" $ (57,2 mm) 3 I 3/4NPT** I UPRIGHT CROSS SECTION 1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to 2 - Button Assembly 5 - Compression orifice seat on frame. Screw **Pipe thread connections per ISO 7/1 can be provided on special request. FIGURE 3 STANDARD RESPONSE SERIES TY-B UPRIGHT (TY4 151) AND PENDENT (TY4251) SPRINKLERS 8.0 K-FACTOR, 3/4 INCH NPT 7/16' (11,1 mm) 1/2" ** NOMINAL SSU* MAKE-IN DEFLECTOR NPT i I ESCUTCHEON PLATE SEATING SURFACE 2-1/4" (57,2 mm) 1-9/16" (39,7 mm) ..-. 55p* DEFLECTOR PENDENT 4 iIYM WRENCH FLATS CROSS UPRIGHT SECTION 1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to 2 - Button Assembly 5 - Compression orifice seat on frame. Screw **Pipe thread connections per ISO 7/1 can be provided on special request. FIGURE 4 STANDARD RESPONSE SERIES TY-B UPRIGHT (TY4851) AND PENDENT (TY4951) SPRINKLERS 8.0 K-FACTOR, 112 INCH NPT Page 4 of 8 TFPISI SPRINKLER FINISH (See Note 8) K TYPE TEMP. BULB LIQUID NATURAL BRASS I CHROME PLATED I WHITE IPOLYESTER LEAD COATED I WAX COATED I WAX OVER LEAD COATED 2.8 1/2" NPT PENDENT (TY1251) and UPRIGHT (TYII5I) 135°F/57°C Orange 1,2,3 N/A 155°F/68C Red 175°F179'C Yellow 200°F/93°C Green 286°F/141°C Blue 360°F/182°C Mauve 1,2 5.6 1/? NPT PENDENT (TY3251) and UPRIGHT (1Y3151) 135°F/57C Orange 1,2,3,4,5,6,7 1,2,3,5 1,2,3,5 1,2,3,5 155'F/68°C Red 175FI79'C Yellow 200FI93°C Green 286F/141°C Blue 1**,2**, 3** 5** 2**, 3** 5** 360°F/182C Mauve N/A RECESSED PENDENT (TY3251)* Figure 4 135°F/57*C Orange 1, 2, 3,4, 5 N/A 155°F168°C Red 175F/79°C Yellow 200°F193°C Green 286°F/141°C Blue 1,2 8.0 NPT PENDENT (TY4251) and UPRIGHT (TY4151) 135°F/57C Orange 1,2,3,4,5,6, 7 1,2,5 1,2,3,5 1,2,5 155°F/68°C Red 175°F179°C Yellow 200°F193°C Green 286F/141°C Blue 1**,2**, 3** 5** 2**, 5** 360°F/1 82C Mauve N/A RECESSED PENDENT (1Y4251)* Figure 5 135°F/57C Orange 1,2, 3,4, 5 N/A 1,2 155°F/68'C Red 175°F/79°C Yellow 200°F193°C Green 286°F/141°C Blue 8.0 1/2" NPT PENDENT (1Y4951) and UPRIGHT (TY4851) 135F/57'C Orange 1, 2, 3,4, 5, 6 N/A 155°F/68C Red 175°F/79°C Yellow 200°F/93°C Green 286°F/141°C Blue 360F/182°C Mauve NOTES: Listed by Underwriters Laboratories, Inc. (UL). Listed by Underwriters Laboratories, Inc. for use in Canada (C-UL). Approved by Factory Mutual Research Corporation (FM). Approved by the Loss Prevention Certification Board (LPCB Ref. No. 007k/03). Approved by the City of New York under MEA 354-01-E. VdS Approved (For details contact Tyco Fire & Building Products, Enschede, Netherlands, Tel. 31-53-428-4444/Fax 31-53-428-3377). Approved by the Loss Prevention Certification Board (LPCB Ref. No. 094a/05). Where Polyester Coated, Lead Coated, Wax Coated, and Wax over Lead Coated Sprinklers are noted to be UL and C-UL Listed, the sprinklers are UL and C-UL Listed as Corrosion Resistant Sprinklers. Where Lead Coated, Wax Coated, and Wax over Lead Coated Sprinklers are noted to be FM Approved, the sprinklers are FM Approved as Corrosion Resistant Sprinklers. * Installed with Style 10 (1/2" NPT) or Style 40 (3/4" NPT) 3/4" Total Adjustment Recessed Escutcheon, as applicable. ** 150°F/66°C Maximum Ceiling Temperature. Frame and deflector only. Listings and approvals apply to color (Special Order). TABLE A, LABORATORY LISTINGS AND APPROVALS TFPI5I Page 5 of 8 SPRINKLER FINISH K TYPE NATURAL CHROME WHITE LEAD WAX WAX OVER BRASS PLATED I POLYESTER I COATED COATED LEAD COATED 28 PENDENT(TY1251) 1/2 and 175 PSI (12,1 BAR) N/A NPT UPRIGHT (TYII5I) PENDENT (TY3251) 5.6 and 250 PSI (17,2 BAR) 175 PSI (12,1 BAR) 1/2° UPRIGHT (TY3151) OR NPT 175 PSI (12,1 BAR) RECESSED PENDENT (Y3251) (SEE NOTE 1) N/A 80 PENDENT(TY4251) 3/4" and 175 PSI (12,1 BAR) NPT UPRIGHT (TY4151) RECESSED PENDENT (TY4251) 175 PSI (12,1 BAR) N/A PENDENT(TY4951) 1/2° and 175 PSI (12,1 BAR) NPT UPRIGHT (TY4851) NOTE: 1. The maximum working pressure of 250 psi (17,2 bar) only applies to the Listing by Underwriters Laboratories, Inc. (UL); the Listing by Underwriters Laboratories, Inc. for use in Canada (C-UL); and, the Approval by the City of New York. TABLE B, MAXIMUM WORKING PRESSURE Technical Data Approvals UL and C-UL Listed. FM, LPCB, VdS, and NYC Approved. (Refer to Table A for complete ap- proval information including corrosion resistant status.) Maximum Working Pressure Refer to Table B. Discharge Coefficient K = 2.8 GPM/p51112 (40,3 LPM/barl'2) K = 5.6 GPM/psi1l2 (80,6 LPM/bar1'2) K = 8.0 GPM/psi1'2 (115,2 LPM/bar1'2) Temperature Ratings Refer to Table A. Finishes Sprinkler: Refer to Table A. Recessed Escutcheon: White Coated, Chrome Plated, or Brass Plated. Physical Characteristics Frame .............Bronze Button .........Brass/Copper Sealing Assembly .......... Beryllium Nickel w/Teflont Bulb ...............Glass Compression Screw .....Bronze Deflector ...........Copper Bushing (K=2.8) .......Bronze Operation The glass Bulb contains a fluid which expands when exposed to heat. When the rated temperature is reached, the fluid expands sufficiently to shatter the glass Bulb, allowing the sprinkler to activate and water to flow. Design Criteria The Series TY-B Pendent and Upright Sprinklers are intended for fire protec- tion systems designed in accordance with the standard installation rules rec- ognized by the applicable Listing or Approval agency (e.g., UL Listing is based on the requirements of NFPA 13, and FM Approval is based on the requirements of FM's Loss Prevention Data Sheets). Only the Style 10 or 40 Recessed Escutcheon, as applicable, is to be used for recessed pendent installations. Page 6 of 8 2-7/8' DIA. (73,0 mm) 5/8±1/4" 3/4" (19,11 mm) I (15,9±6,4 mm) _ 2-1/4' DIA. 1/4 (6,4 mm) MOUNTING FACE OF SPRINKLER PLATE FITTING -__L m 1/8" =4d (3,2 mm) __ MOUNTING SURFACE/ CLOSURE SERIES 1-1/4" (31,8 mm) I TYB 3/4(19,1 mm) FIGURE 5 SERIES TY-B RECESSED PENDENT SPRINKLER ASSEMBLY WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT STYLE 10 RECESSED ESCUTCHEON 5.6 K-FACTOR, 1/2 INCH NPT 2-7/8" DIA. "I 5/8±1/4" (73,0 mm) 3/4"(19,1 mm) (15,9±6,4 mm) 2-1/4" DI A. I 1/4" (6,4 mm) (57,2 mm) FACE OF MOUNTING I SPRINKLER I PLATE FITTING I 1/8" 3,2 mm) MOUNTING / SURFACE/ / CLOSURE SERIES 1-5/16" (33,3 mm) TY-B 13/16" (20,6 mm) FIGURE 6 SERIES TY-B RECESSED PENDENT SPRINKLER ASSEMBLY WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT STYLE 40 RECESSED ESCUTCHEON 8.0 K-FACTOR, 3/4 INCH NPT TFPI5I WRENCH RECESS (END "A" USED FOR 1/2" NPT MODELS) WRENCH RECESS (END "B" USED FOR 3/4" NPT MODELS) FIGURE 7 W-TYPE 6 SPRINKLER WRENCH WRENCH RECESS PUSH WRENCH IN TO ENSURE ENGAGEMENT WITH SPRINKLER WRENCHING AREA FIGURE 8 W-TYPE 7 RECESSED SPRINKLER WRENCH Installation The Series TY-B Sprinklers must be installed in accordance with the follow- ing instructions: NOTES Do not install any bulb type sprinkler if the bulb is cracked or there is a loss of liquid from the bulb. With the sprinkler held horizontally, a small air bubble should be present. The diameter of the air bubble is approximately 1/16 inch (1,6 mm) for the 135°F/57°C to 3/32 inch (2,4 mm) for the 360 °F/182"C temperature ratings. A 1/2 inch NPT sprinkler joint should be obtained with a minimum to maxi- mum torque of 7 to 14 ft.lbs. (9,5 to 19,0 Nm). A 3/4 inch NPT sprinkler joint should be obtained with a mini- mum to maximum torque of 10 to 20 ft.lbs. (13,4 to 26,8 Nm). Higher levels of torque may distort the sprinkler inlet and cause leakage or impairment of the sprinkler. Do not attempt to make-up for insuffi- cient adjustment in the escutcheon plate by under- or over-tightening the TFPI5I Page 7 of 8 sprinkler. Readjust the position of the sprinkler fitting to suit. The Series TV-B Pendent and Up- right Sprinklers must be installed in accordance with the following instruc- tions. Step 1. Pendent sprinklers are to be installed in the pendent position, and upright sprinklers are to be installed in the upright position. Step 2. With pipe thread sealant ap- plied to the pipe threads, hand tighten the sprinkler into the sprinkler fitting. Step 3. Tighten the sprinkler into the sprinkler fitting using only the W-Type 6 Sprinkler Wrench (Ref. Figure 7), except that an 8 or 10 inch adjustable Crescent wrench is to be used for wax coated sprinklers. With reference to Figures 1, 2, 3, and 4 the W-Type 7 Sprinkler Wrench or the adjustable Crescent wrench, as applicable is to be applied to the wrench flats. When installing wax coated sprinklers with the adjustable Crescent wrench, additional care needs to be exercised to prevent damage to the wax coating on the sprinkler wrench flats or frame arms and, consequently, exposure of bare metal to the corrosive environ- ment. The jaws of the wrench should be opened sufficiently wide to pass over the wrench flats without damag- ing the wax coating. Before wrench tightening the sprinkler, the jaws of the wrench are to be adjusted to just con- tact the sprinkler wrench flats. After wrench tightening the sprinkler, loosen the wrench jaws before removing the wrench. After installation, the sprinkler wrench flats and frame arms must be in- spected and the wax coating re- touched (repaired) whenever the coat- ing has been damaged and bare metal is exposed. The wax coating on the wrench flats can be retouched by gen- tly applying a heated 1/8 inch diameter steel rod to the areas of wax that have been damaged, to smooth it back over areas where bare metal is exposed. NOTES Only retouching of the wax coating ap- plied to the wrench flats and frame arms is permitted, and the retouching is to be performed only at the time of the initial sprinkler installation. The steel rod should be heated only to the point at which it can begin to melt the wax, and appropriate precautions need to be taken, when handling the heated rod, in order to prevent the installer from being burned. The Series TY-B Recessed Pendent Sprinklers must be installed in ac- cordance with the following instruc- tions. Step A. After installing the Style 10 or 40 Mounting Plate, as applicable, over the sprinkler threads and with pipe thread sealant applied to the pipe threads, hand tighten the sprinkler into the sprinkler fitting. Step B. Tighten the sprinkler into the sprinkler fitting using only the W-Type 7 Recessed Sprinkler Wrench (Ref. Figure 8). With reference to Figure 3 or 4, the W-Type 7 Recessed Sprinkler Wrench is to be applied to the sprinkler wrench flats. Step C. After the ceiling has been in- stalled or the finish coat has been ap- plied, slide on the Style 10 or 40 Clo- sure over the Series TY-B Sprinkler and push the Closure over the Mount- ing Plate until its flange comes in con- tact with the ceiling. Care and Maintenance The Series TV-B Sprinklers must be maintained and serviced in accord- ance with the following instructions: NOTES Before closing a fire protection system main control valve for maintenance work on the fire protection system that it controls, permission to shut down the affected fire protection system must be obtained from the proper authorities and all personnel who may be affected by this action must be notified. The owner must assure that the sprin- klers are not used for hanging of any objects; otherwise, non-operation in the event of a fire or inadvertent opera- tion may result. Absence of an escutcheon, which is used to cover a clearance hole, may delay the time to sprinkler operation in a fire situation. Sprinklers that are found to be leaking or exhibiting visible signs of corrosion must be replaced. Automatic sprinklers must never be painted, plated, coated or otherwise altered after leaving the factory. Modi- fied sprinklers must be replaced. Sprinklers that have been exposed to corrosive products of combustion, but have not operated, should be replaced if they cannot be completely cleaned by wiping the sprinkler with a cloth or by brushing it with a soft bristle brush. Care must be exercised to avoid dam- age to the sprinklers - before, during, and after installation. Sprinklers dam- aged by dropping, striking, wrench twist/slippage, or the like, must be re- placed. Also, replace any sprinkler that has a cracked bulb or that has lost liquid from its bulb. (Ref. Installation Section). Frequent visual inspections are rec- ommended to be initially performed for corrosion resistant coated sprinklers, after the installation has been com- pleted, to verify the integrity of the cor- rosion resistant coating. Thereafter, annual inspections per NFPA 25 should suffice; however, instead of in- specting from the floor level, a random sampling of close-up visual inspec- tions should be made, so as to better determine the exact sprinkler condi- tion and the long term integrity of the corrosion resistant coating, as it may be affected by the corrosive conditions present. The owner is responsible for the in- spection, testing, and maintenance of their fire protection system and de- vices in compliance with this docu- ment, as well as with the applicable standards of the National Fire Protec- tion Association (e.g., NFPA 25), in addition to the standards of any other authorities having jurisdiction. The in- stalling contractor or sprinkler manu- facturer should be contacted relative to any questions. Automatic sprinkler systems should be inspected, tested, and maintained by a qualified Inspection Service in ac- cordance with local requirements and/or national codes. Page 8 of 8 TFPI5I PIN 57-XXX-X-XXX I L MODEL/SIN 530 2.8K UPRIGHT (1/2"NPT) TY1151 531 2.8K PENDENT (1/2"NPT) TY1251 570 5.6K UPRIGHT (1/2"NPT) TY3151 571 1 5.6K PENDENT (1/2"NPT) TY3251 590 8.0K UPRIGHT (3/4"NPT) TY4151 591 8.0K PENDENT (3/4"NPT) TY4251 8.0K UPRIGHT (1/2"NPT) TY4851 F560 561 8.OK PENDENT (1/2"NPT) TY4951 I SPRINKLER I TEMPERATUF RATING 135 135°F/57°C 155 155F/68°C 175 175°F/79°C 200 200°F/93°C 286 28&F/141°C 360 360F/182°C 286°F/141°C MAX. 1 NATURAL BRASS 4 WHITE POLYESTER 3 WHITE (RAL9010) * 9 CHROME PLATED 7 LEAD COATED 6 WAX COATED 8 I WAX OVER LEAD 286°F/141°C MAX. * Eastern Hemisphere sales only. TABLE C PART NUMBER SELECTION SERIES TY-B PENDENT AND UPRIGHT SPRINKLERS Limited Warranty Products manufactured by Tyco Fire & Building Products (TFBP) are war- ranted solely to the original Buyer for ten (10) years against defects in mate- rial and workmanship when paid for and properly installed and maintained under normal use and service. This warranty will expire ten (10) years from date of shipment by TFBP. No warranty is given for products or com- ponents manufactured by companies not affiliated by ownership with TFBP or for products and components which have been subject to misuse, improper installation, corrosion, or which have not been installed, maintained, modi- fied or repaired in accordance with ap- plicable Standards of the National Fire Protection Association, and/or the standards of any other Authorities Having Jurisdiction. Materials found by TFBP to be defective shall be either repaired or replaced, at TFBP's sole option. TFBP neither assumes, nor authorizes any person to assume for it, any other obligation in connection with the sale of products or parts of prod- ucts. TFBP shall not be responsible for sprinkler system design errors or inac- curate or incomplete information sup- plied by Buyer or Buyer's repre- sentatives. In no event shall TFBP be liable, in contract, tort, strict liability or under any other legal theory, for incidental, indirect, special or consequential dam- ages, including but not limited to labor charges, regardless of whether TFBP was informed about the possibility of such damages, and in no event shall TFBP's liability exceed an amount equal to the sales price. This limited warranty sets forth the ex- clusive remedy for claims based on failure of or defect in products, materi- als or components, whether the claim is made in contract, tort, strict liability or any other legal theory. This warranty will apply to the full ex- tent permitted by law. The invalidity, in whole or part, of any portion of this warranty will not affect the remainder. Ordering Procedure When placing an order, indicate the full product name. Refer to the Price List for complete listing of Part Num- bers. Contact your local distributor for avail- ability. Sprinkler Assemblies with NPT Thread Connections: Specify: (Specify Model/SIN), Stand- ard Response, (specify K-factor), (specify temperature rating), Series TY-B (specify Pendent or Upright) Sprinkler with (specify type of finish or coating), P/N (specify from Table C). Recessed Escutcheon: Specify: Style (specify 10 or 40 ) Re- cessed Escutcheon with (specify*) fin- ish, P/N (specify*). Refer to Technical Data Sheet TFP770. Sprinkler Wrench: Specify: W-Type 6 Sprinkler Wrench, P/N 56-000-6-387. Specify: W-Type 7 Sprinkler Wrench, P/N 56-850-4-001. © 2007 TYCO FIRE & BUILDING PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446 tamed when expos mospheres. Althou tant coated sprinklE standard corrosion cable approval age not representative rosive atmosphere is recommended t consulted with resp of these coatings f sive environment. 1 ent temperature, chemicals, and ga should be consider along with the corr chemical to which ti exposed. An intermediate le Series TY-FRB P are detailed in Te TFP356, and Sprin tailed in Technical I i to corrosive at- 1 corrosion resis- havepassed the ?sts Of the appli- ies, the testing is all possible cor- Consequently, it the end user be t to the suitability any given corro- e effects of ambi- oncehtration of hemiôal velocity, i, as a minimum, lye nature of the sprinklers will be 1 versions of the rdent Sprinklers nical Data Sheet Dr Guards are de- ta Sheet TFP780 The Series TY-Fl 3 Sprinklers de- scribed herein mus be installed and maintained in coir ,liance with this document, as well a with the applica- ble standards of the \Jational Fire Pro- tection Association, in addition to the standards of any otl .r authorities hay- ing jurisdiction. Fail ,re to do so may impair the perform nce of these do- vices. The owner is respor e for main fain- ing their fire protecti :ystem and de- vices in proper op ing condition. The installing conti r or sprinkler manufacturer shoi be contacted with any questions. tqco IF/re & Buiki/ng I Products Technical Services: Tel: (800) 381-9312 I Fax: (800) 791 Series TY-FRB - 28,4.2, 5.6, and 8.0 K-factor Upright, Pendent, and F Recessed Pendent Sprinklers Quick Response, Standard ;verage General Description The Tyco® Series TY-FRB, 2.8, 4.2, 5.6, and 8.0 K-factor, Upright and Pen- dent Sprinklers described in this data sheet are quick response - standard coverage, decorative 3 mm glass bulb type spray sprinklers designed for use in light or ordinary hazard, commercial occupancies such as banks, hotels, shopping malls, etc. The recessed version of the Series TY-FRB Pendent Sprinkler, where ap- plicable, is intended for use in areas with a finished ceiling. It uses either a two-piece Style 10 (1/2 inch NPT) or Style 40 (3/4 inch NPT) Recessed Es- ci'tcheon with 1/2 inch (12,7 mm) of recessed adjustment or up to 3/4 inch (19,1 mm) of total adjustment from the flush pendent position, or a two-piece Style 20(1/2 inch NPT) or Style 30(3/4 inch NPT) Recessed Escutcheon with 1/4 inch (6,4 mm) of recessed adjust- ment or up to 1/2 inch (12,7 mm) of total adjustment from the flush pen- dent position. The adjustment pro- vided by the Recessed Escutcheon re- duces the accuracy to which the fixed pipe drops to the sprinklers must be cut. Corrosion resistant coatings, where applicable, are utilized to extend the life of copper alloy sprinklers beyond that which would otherwise be ob- IMPORTANT Always refer to Technical Data: Sheet TFP700 for the 'INSTALLER WARNING" that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and in- stallation can permanently damage a sprinkler system or its compo- nents and cause the sprinkler to fail to operate in a fire situation or cause it to operate prematurely. Model/Sprinkler Identification Numbers TYII3I - Upright 2.81K, 1/2"NPT TY1231 - Pendent 2.81K, 1/2"NPT TY2131 - Upright 4.21K, 1/2"NPT TY2231 - Pendent 4.21K, 1/2"NPT TY3131 - Upright 5.61K, 1/2"NPT TY3231 - Pendent 5.6K, 1/2"NPT TY4131 - Upright 8.01K, 3/4'NPT TY4231 - Pendent 8.0K, 3/4NPT TY4831- Upright 8.01K, 1/2"NPT TY4931- Pendent 8.0K, 1/2"NPT Page 1 of 10 AU ',2007 TFPI7I SSU* LH. 1/2" NPT UPRIGHT * Temperature r orifice seat on fra I 131) AND PENDE INCH NPT Page 2 of 10 ESCUTCHEON 7/16(11,1 mm) STYLE 100r20 PLATE SEATING ,, NOMINAL RECESSED SURFACE 1/2 MAKE-IN ESCUTCHEON 2-1/4" (57,2 mm) 1-9/16" (39,7 mm) SSP DEFLECTOR * PENDENT 1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector 2 - Button Assembly 5 - Compression 7 - Bushing Screw QUICK RESPONSE SERIES TY-FRB UPRIGHT (1 2.8 K-FACTOR, TFP171 6 7/16 5 1,1 mm) I 4 )MINAL 2 AKE-IN 1; 2-3/16" 3 J. (55,6 mm) CROSS SECTION is indicated on deflector or adjacent to (TY1231) SPRINKLERS H 2-7/8" (73,0 mm) DIA. RECESSED PENDE STYLE 10 or 20 ESCUTCHEON 7/16" (11,1 mm) PLATE SEATING ,, NOMINAL SURFACE NPT MAKE-IN 2 (55 m) (38,1 mm) SSP DEFLECTOR 2-7/ * 8" (73,0 mm) DIA. PENDENT RECESSED PENDE 6* 7/16" I 5 (11,1 mm) NOMINAL I MAKE-IN / ±L 2-3/16" (55,6 mm) 1 CROSS SECTION 1/2" NPT UPRIGHT 1 - Frame 3 - Sealing 4 - Bulb 6- Deflector * Temperature rating is indicated on deflector or adjacent to 2 - Button Assembly 5 - Compression orifice seat on frame. Screw FIGURE QUICK RESPONSE SERIES TY.FRB UPRIGHT (TY2I31) AND PENDENT (TY2231) SPRINKLERS 4.2 K-FACTOR, 112 INCH NPT 6* 1/2" 5 ,7 mm) I MINAL I WE-IN 2-1/4" 1 (57,2 mm) CROSS SECTION 3/4" NPT UPRIGHT TFPI7I ESCUTCHEON I7/16' (11,1 mm) PLATE SEATING ,, NOMINAL SURFACE MOT MAKE-IN 2-3/16" (55,6 mm) 1-1/2" (38,1 mi SSP DEFLECTOR * PENDENT Page 3 of 10 STYLE 10 20 RECESSD * ESCUTCHEON SSU DEFLECTOR JN Mir H (55,6 mm) 1/2' NPT UPRIGHT CROSS SECTION *1 Temperature rating is indicated on deflector or adjacent to Orifice seat on frame. 3 , 131) AND PENDENT (TY3231) SPRINKLERS ! INCH NPT H 2-7/8" (73,0 mm) DIA. RECESSED PENDE 1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector 2 - Button Assembly 5 - Compression Screw QUICK RESPONSE SERIES TY-FRB UPRIGHT 5.6 K-FACTO STYLE 30 or 40 ESCUTCHEON 1/2(12,7mm) PLATE SEATING • ,, NOMINAL SURFACE 3/4 NPT MAKE-IN Mom (58m) (3 mm)d] SSP DEFLECTOR * - 2-7/8" (73,0 mm) DIA. PENDENT RECESSED PENDE SSU * is indicated on deflector or adjacent to 1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature 2 - Button Assembly 5 - Compression orifice seat on Screw I FIGURE 4 QUICK RESPONSE SERIES TY-FRB UPRIGHT (TY4131) AND F (TV4231) SPRINKLERS 8.0 K-FACTOR, i/4 INCH NPT Page 4 of 10 TFPI 71 7/16(11,1 men) NOMINAL SSU 1/2" MAKE-IN r DEFLECTOR NPT i 2-1/4 (57,2 mm) 1-9/16' (39,7 mm) = WRENCH FLATS SSP * CROSS PENDENT I UPRIGHT - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature 2 - Button Assembly 5 - Compression Orifice seat on Screw FIGURE QUICK RESPONSE SERIES TY-FRB UPRIGHT (TY4831) AND P 8.0 K-FACTOR,1/2 INCH NPT is indicated on deflector or adjacent to (TY4931) SPRINKLERS Technical Data Approvals UL and C-UL Listed. FM, LPCB, and NYC Approved. (Refer to Table A and .B for complete approval information including corro- sion resistant status.) Maximum Working Pressure Refer to Table C. Discharge Coefficient K = 2.8 GPM/psi112 (40,3 LPM/bar112) K = 4.2 GPM/p51112 (60,5 LPM/barll2) K = 5.6 GPM/p5i112 (80,6 LPM/bar112) K = 8.0 GPM/p5i112 (115,2 LPM/bar1l2) Temperature Ratings Refer to Table A and B Finishes Sprinkler: Refer to Table A and B. Recessed Escutcheon: White Coated, Chrome Plated, or Brass Plated. Physical Characteristics Frame .............Bronze Button ..........Brass/Copper Sealing Assembly .......... Beryllium Nickel w/Teflont Bulb ...............Glass Compression Screw .....Bronze Deflector .......Copper/Bronze Bushing (K=2.8) .......Bronze Operation The glass Bulb contains a fluid which expands when expoed to heat. When the rated temperature is reached, the fluid expands sufficintly to shatter the glass Bulb, allowing the sprinkler to activate and water to flow. Design Criteria The Series TY-FRB Pendent and Up- right Sprinklers are intended for fire protection systems designed in ac- cordance with the standard installation rules recognized by the applicable Listing or Approval agency (e.g., UL Listing is based on the requirements of NFPA 13, and FM Approval is based on the requirementsof FM's Loss Pre- vention Data Sheets ). Only the Style 10, 20, 30, or 40 Recessed Escutch- eon, as applicable, Jis to be used for recessed pendent installations. TFPI7I SPRINKLER FINISH (See Note 7) K TYPE TEMP. BULB LIQUID NATURAL BRASS I CHROME PLATED I WHITE JPOLYESTE 2.8 1/2" PENDENT (TY1231) and UPRIGHT (TYII3I) 135°F/57°C Orange 1,23,5 —1-- 155°F168°C Red 175°F/79°C Yellow 200°FI93C Green 286°F1141°C Blue NPT RECESSED PENDENT (TY1231)* Figure 6 135°F/57°C Orange 1, 2, 5 155°F168°C Red 175°F/79°C Yellow 200°F193°C Green RECESSED PENDENT (TY1231)** Figure 7 135°F157°C Orange 155°F168°C Red .175°FI79C Yellow 200FI93C Green 4.2 1/2" NPT PENDENT (TY2231) and UPRIGHT (1Y2131) 135°F!57°C Orange 1,2 155°F/68°C Red 175°F179°C Yellow 2O0F/93°C Green 286°F/141C Blue RECESSED PENDENT (TY2231)* Figure 8 135°F/57°C Orange 155°F168°C Red 175°F/79°C Yellow 200F/93°C Green 135°F/57°C Orange RECESSED PENDENT (TY2231) Figure 9 155°F168°C Red 175°F/79°C Yellow 200°F/93C Green NOTES: Listed by Underwriters Laboratories, Inc. (UL) as Quick Response Sprinklers. Listed by Underwriters Laboratories, Inc. for use in Canada (C-UL) a Quick Re- sponse Sprinklers. Approved by Factory Mutual Research Corporation (FM) as Quick Response Sprin- klers. 5. Approved by the City of New York under MEA 354-01-E. 7. Where Polyester Coated Sprinklers are noted to be UL and C-UL Lis ed, the sprin- klers are UL and C-UL Listed as Corrosion Resistant Sprinklers. * Installed with Style 10 (1/2" NPT) or Style 40 (3/4" NPT) 3/4" Total Adjustment Recessed Escutcheon, as applicable. ** Installed with Style 20 (1/2" NPT) or Style 30 (3/4" NPT) 1/2" Total Adjustment Recessed Escutcheon, as applicable. Frame and Deflector only. Listings and approvals apply to color (Special Order). N/A: Not Available TABLE A LABORATORY LISTINGS AND APPROVALS 2.8 AND 4.2 K-FACTOR SPRINKLERS Page 5 of 10 Page 6of1O TFPI7I SPRINKLER FINISI- (See Note 8) K TYPE TEMP. BULB NATURAL CHROME WHITE*** LEAD LIQUID BRASS PLATED POLYESTER COATED 135°F/57°C Orange PENDENT (TY3231) and 1,2,3,4, ,6,7 1,2,3,5 155°F/68°C Red 175°F/79°C Yellow UPRIGHT 200°F/93°C Green 5.6 (TY3131) 1/2" 286°F/141°C Blue NPT 135°F/57°C Orange RECESSED PENDENT (TY3231)* 1,2,4, 5 N/A 155F/68°C Red 175°F/79°C Yellow Figure 10 200°F/93°C Green 135F/57C Orange RECESSED PENDENT (TY3231)** 1, 2, 3, , 5 N/A 155°F/68°C Red 175°F/79°C Yellow Figure 11 200°F/93C Green 135°F/57C Orange PENDENT (TY4231) and 1, 2,3,4,5,6,7 1,2,5 155°F/68°C Red 175°F/79°C Yellow 200F/93°C Green UPRIGHT 8.0 (TY4131) 3/4" 286°F/141°C Blue NPT 135F/57C Green RECESSED PENDENT (TY4231)* 1, 2, 4, 5 N/A 155 F/68 C Orange 175°F/79°C Red Figure 12 200°F/93°C Yellow 135F/57°C Orange RECESSED PENDENT (TY4231) 1, 2, 3, ,5 N/A 155°F/68°C Red 175°F/79C Yellow Figure 13 200F/93°C Green Orange 8.0 1/2" NPT PENDENT (TY4931) and UPRIGHT 1,2,4,5,6 1,2,5 d Re 4286'F/141'C Yellow Green (TY4831) Blue NOTES: I 1. Listed by Underwriters Laboratories, Inc. (UL) as Quick Response Srinkler. . Listed by Underwriters Laboratories, Inc. for use in Canada (C-UL) as Quick Response Sprinki rs. Approved by Factory Mutual Research Corporation (FM) as Quick Response Sprinklers. Approved by the Loss Prevention Certification Board (LPCB Ref. No. 007k/04) as Quick Respo se Sprinklers; however, the LPCB does not rate the thermal sensitivity of recessed sprinklers. Approved by the City of New York under MEA 354-01-E. VdS Approved (For details contact Tyco Fire & Building Products, Enschede, Approved by the Loss Prevention Certification Board (LPCB Ref. No.094a/06) Where Polyester Coated and Lead Coated Sprinklers are noted to be Netherlands, Tel. as Quick Respi UL and C-UL Listed, the 31-53-428-4444/Fax 31-53-428-3377). se Sprinklers. 'sprinklers are UL and C-UL Listed as Corrosion Resistant Sprinklers. Where Lead Coated Sprinklers are noted to be FM Approved, tie sprinklers are FM Approved as a Corrosion Resistant Sprinklers. * Installed with Style 10 (1/2' NPT) or Style 40 (3/4" NPT) 3/4" Total Adjustment ** Installed with Style 20 (1/2" NPT) or Style 30 (3/4" NPT) 1/2" Total Adjustment Frame and Deflector only. Listings and approvals apply to color (Special Recessed Escu Recessed Escu Order). cheon, as applicable. cheon, as applicable. N/A: Not Available TABU: Z5 LABORATORY LISTINGS AND APPROVALS 5.6 AND 8.0 K-FACTOR SPRINKLERS TFP17I Page 7 of 10 SPRINKLER IfINISH K TYPE NATURAL CHROME WHITE - LEAD• BRASS PLATED POLYESTER COATED PENDENT (1Y3231) and 2.8 LJPRIGHT(TY3131) 175 PSI (121 BAR) N/A RECESSED PENDENT NPT (1Y323) . PENDENT (1Y4231) and 4.2 UPRIGHT (1Y4131) 175 PSI (121 BAR) N/A RECESSED PENDENT NPT (TY4231) PENDENT(TY3231) and 250 PSI(1712 5 BAR) 175 PSI (12,1 BAR) .6 UPRIGHT (TY3131) OR NPT RECESSED PENDENT PSI (121 BAR) (TY3231) (SEE NOTE 1) N/A PENDENT (TY4231) and 175 PSI (121 BAR) 175 PSI (12,1 BAR) 8.0 UPRIGHT (1Y4131) I RECESSED PENDENT NPT (TY4231) ' N/A 8 PENDENT (V4931) 1/2" and 175 PSI (12,1 BAR) 175 PSI (12,1 BAR) NPT UPRIGHT(TY4831) NOTES: 1. The maximum working pressure of 250 psi (17,2 bar) only applies Listing by Underwrites Laboratories Inc. (UL); the Listing by Underwriters Laboratories, Inc. for use in Canada (C-UL): and the 31 by the City of New pork. TABLE C, MAXIMUM PRESSURE Installation The Series TY-FRB Sprinklers must be installed in accordance with the fol- lowing instructions: NOTES Do not install any bulb type sprinkler if the bulb is cracked or there is a loss of liquid from the bulb. With the sprinkler held horizontally, a small air bubble should be present. The diameter of the air bubble is approximately 1/16 inch (1,6 mm) for the 135°F/57C to 3/32 inch (2,4 mm) for the 286°F/141°C temperature ratings. A leak fight 1/2 inch NPTsprinklerjoint should be obtained with a torque of 7 to 14 ft.lbs. (9,5 to 19,0 Nm). A maxi- mum of 21 ft. lbs. (28,5 Nm) of torque may be used to install sprinklers with 1/2 NPT connections. A leak tight 3/4 inch NPT sprinkler joint should be ob- ta/ned with a torque of 10 to 20 ft.lbs. (13,4 to 26,8 Nm). 4 maximum of 30 ft.lbs. (40,7 Nm) of tckque is to be used to install sprinklers 'vith 3/4 NPT con- nections. Higher levels of torque may distort the sprinkler' inlet and cause leakage or impairment of the sprinkler. Do not attempt to make-up for insuffi- cient adjustment hi the escutcheon plate by under- or o,ver-tightening the sprinkler. Readjust the position of the sprinkler fitting to stilt. The Series TY-FRB Pendent and Up- right Sprinklers must be installed in accordance with the following instruc- tions. Step 1. Pendent sprinklers are to be installed in the penent position, and upright sprinklers are to be installed in the upright position.J Step 2. With pipe tjread sealant ap- plied to the pipe threads, hand tighten e sprinkler into the sprinkler fitting. Up 3. Tighten the sprinkler into the prinkler fitting using only the W-Type Sprinkler Wrench (Ref. Figure 14). ith reference to Figures 1, 2, 3, 4, and 5, the W-Type 6 Sprinkler Wrench i lobe applied to the sprinkler wrench e Series TY-FRB Recessed Pen- nt Sprinklers must be installed in ordance with the following instruc- tep A. After installing the Style 10. J, 30, or 40 Mounting Plate, as appli- able, over the sprinkler threads and ith pipe thread sealant applied to the pe threads, hand tighten the sprin- er into the sprinkler fitting. tep B. Tighten the sprinkler into the prinkler fitting using only the W-Type Recessed Sprinkler Wrench (Ref. igure 15). With reference to Figure 1, 3, and 4, the W-Type 7 Recessed Page 8 of 10 2-7/8 DIA. 5/8±1/4" (73,0 mm) 3/4"(19,1 mm) SPRINKLE*R 1 PLATE FACE OF L57'2 mm) MOUNTING (15,9±6,4 mm) 2-1/4" DIA. 1/4" (6,4 mm) 1 FITTING (3,2 mm) MOUNTIN SURFACE CLOSURE SERIES 1-5/16" (33,3 mm) TY-FRB 13/16" (20,6 mm) FIGURE 6 SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT STYLE 10 RECESSED ESCUTCHEON 2.8 K-FACTOR, 1/2 INCH NPT TFPI7I 2-7/8" DIA. (73,0 mm) 1/2"(12,7 mm) 2-1/4" DIA. (57,2 mm) 1/4"(6,4 mm) MOUNTING - fli ATM 1/8 (3,2 mm) 1-5/16" (33,3 mm) 1-1/16" (27,0 mm) FIGURE 7 SERIES TY.FRB RECESSED PENDENT WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 20 JECESSED ESCUTCHEON 2.8 K-ACTOR, 1/2 INCH NPT 1/2±1/8" (12.7±3,2 mm) FACE OF SPRINKLER FITTING \ - MOUNTING SURFACE CLOSURE SERIES TY-FRB - 2-7/8" DIA. 5/8±1/4" (73,0 mm) I 3/4" (19,1 mm) (15,9±6,4 mm) 2-1/4" DIA. 1/4" (6,4 FACE OF MOUNTING SPRINKLER - , I. 2mm PLATE FITTING (3,2 mm) MOUNTING SURFACE SERIES / 1-1/4" (31,8mm)] CLOSURE TY-FRB 3/4"(19,1 mm) FIGURE 8 SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT STYLE 10 RECESSED ESCUTCHEON 4.2 K-FACTOR, 1/2 INCH NPT (12,7±3,2 mm) FACE OF SPRINKLER I FITTING MOUNTING SURFACE CLOSURE SERIES fl WITH TWO-PIEC STYLE 20 4.2K- - 2-7/8" DIA. (73,0 mm) 1/2" (12.7 mm) - 2-1/4" DIA. 1/4" (6,4 mm) 72 mm) MOUNTING PLATE ERIES 1.1/4" (31,8 mm) YFRB 1" (25,4 mm) FIGURE 9 RB RECESSED PENDENT 1/2 INCH TOTAL ADJUSTMENT ECESSED ESCUTCHEON CTOR, 1/2 INCH NPT Sprinkler Wrench is to be applied to the sprinkler wrench flats. Step C. After the ceiling has been in- stalled or the finish coat has been ap- plied, slide on the Style 10, 20, 30, or 40 Closure over the Series +Y-FRB Sprinkler and push the Closure over the Mounting Plate until its flange comes in contact with the ceiling. Care and Maintenance The Series TY-FRB Sprinklers must be maintained and serviced in accord- ance with the following instructions: NOTES Before closing a fire protection system main control valve for maintenance work on the fire pro( 'ct/on system that it controls, permissic ito shutdown the affected fire protecti n system must be obtained from the roper authorities and all personnel wi maybe affected by this action must. e notified. The owner must as ire that the sprin- kiers are not used r hanging of any objects; otherwise, non-operation in the event of fire or iadvertent opera- tion may result. Absence of an esc n, which is used to cover a Of s hole, may delay the time to sp operation in a fire situation. Sprinklers that are fqund to be leaking or exhibiting visible signs of corrosion must be replaced. Automatic sprinklers must never be painted, plated, coated or otherwise Itered after leaving the factory. Modi- ed sprinklers must be replaced. prinklers that have been exposed to Drrosive products of combustion, but ave not operated, should be replaced they cannot be completely cleaned y wiping the sprinkler with a cloth or y brushing it with a soft bristle brush. are must be exercised to avoid dam- ge to the sprinklers - before, during, nd after installation. Sprinklers dam- ged by dropping, striking, wrench vist/slippage, or the like, must be re- laced. Also, replace any sprinkler at has a cracked bulb or that has lost quid from its bulb. (Ref. Installation ectiorl). requent visual inspections are rec- 'mmended to be initially performed for brrosion resistant coated sprinklers, ter the installation has been com- TFPI7I 2-7/8 DIA. 5/8±1/4" (73,0 mm) I 3/4"(19,1 mm) (15,9±6,4 mm) 2-1/4" DIA. 1/4" (6,4 mm) I FACE OF (57,2 mm) MOUNTING SPRINKLE PLATE FITTING 1/8" (3,2 mm) MOUNTING I SURFACE SERIES 1-1/4" (31,8 mm) CLOSURE TY-FRB 3/4"(19,1 mm) FIGURE 10 SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT STYLE 10 RECESSED ESCUTCHEON 5.6 K-FACTOR, 1/2 INCH NPT 2-7/8" DIA. 5/8±1/4" (73,0 mm) 3/4" (19,1 mm) (15,9±6,4 mm) 2-1/4" DIA. 1/4" (6,4 ml FACE OF I (57,2 mm) MOUNTING SPRINKLER I PLATE FITTING MM) (32 I ____________ _j '7 MOUNTING SURFACE . CLOSURE SERIES 1-5/16" (33,3 Imm) TY-FRB 13/16" (20,6 mm) FIGURE 12 SERIES TV-FRB RECESSED PENDENT WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT STYLE 40 RECESSED ESCUTCHEON 8.0 K-FACTOR, 3/4 INCH NPT Page 9 of 10 2-7/8" DIA. - (73,0 mm) 1/2±1/8" , I 1/2" (12,7 mm) E (12,7±3,2 mm) 2-1/4" DIA. 1/4" (6,4 mm) FACE _OF 2 mm) MOUNTING SPRINKLER PLATE FITTING MOUNTIN (3,2 m) SURFACE/ SERIES 1-1/4" (31,8 mm) CLOSURE TY-FRB 1" (25,4 mm) FIGURE 11 SERIES TV FRB RECESSED PENDENT WITH TWO-PIECE 112 INCH TOTAL ADJUSTMENT STYLE 20 RECESSED ESCUTCHEON 5.6 K-. ACTOR, 1/2 INCH NPT - 2-7/8" DIA. 1/2±1/8" (73,0 mm) 1/2"(12,7mm) E (12,7±3,2 mm) 2-1/4" DIA. I 1/4" (6,4 mm) I FACE OF (57,2 mm) I I I MOUNTING I I PLATE SPRINKLER 1/8" _ II FITTING (3,2 mm) MOUNTING SURFACE , /// CLOSURE SERIES, 1-5/1 6. TYFRB 1-1/16"(27,0 mm) FIGURE 13 SERIES TV-. 'RB RECESSED PENDENT WITH TWO-PIEC 1/2 INCH TOTAL ADJUSTMENT STYLE 30 FECESSED ESCUTCHEON 8.0 K-FACTOR, 3/4 INCH NPT pleted, to verify the integrity of the cor- rosion resistant coating. Thereafter, annual inspections per NFPA 25 should suffice; however, instead of in- specting from the floor level, a random sampling of close-up visual inspec- tions should be made, so as to better determine the exact sprinkler condi- tion and the long term integrity of the corrosion resistant coating, as it may be affected by the corrosive, conditions present. The owner is responsible for the in- spection, testing, and maintenance of their fire protection system and de- vices in compliance with this docu- ment, as well as with the applicable standards of the National Fire Protec- tion Association (e.g., NFPA 25), in addition to the standards of any other authorities having jurisdiction. The in- stalling contractor or sprinkler manu- WRENCH RECESS 1/2" NPT MODELS) WRENCH RECESS (END "B" USED FOR 3/4" NPT MODELS) FIGURE 14 W-TYPE 6 SPRINKLER WRENCH facturer should be 6ontacted relative to any questions. It is recommended that automatic sprinkler systern be inspected, tested, and maintained by a qualified WRENCH RECESS PUSH WRENCH IN TO ENSURE ENGAGEMENT WITH SPRINKLER WRENCHING AREA FIGURE 15 W-TYPE 7 RECESSED SPRINKLER WRENCH ection Service in accordance with I requirements and/or national s. 330 2.8K UPRIGHT (1/2"NPT) TY1131 331 2.8K PENDENT (1/2"NPT) 1Y1231 340 4.2K UPRIGHT (1/2"NPT) TY2131 341 4.2K PENDENT (1/2"NPT) 1Y2231 370 5.6K UPRIGHT (1/2"NPT) TY3131 371 5.6K PENDENT (1/2"NPT) 1Y3231 390 8.OK UPRIGHT (3/4'NPT) 1Y4131 391 8.0K PENDENT (314NPT) TY4231 360 8.OK UPRIGHT (1/2"NPT) 1Y4831* 361 8.0K PENDENT (1/2"NPT) 1Y4931* PIN 57-XXX-X----XXX MODEL/SIN * Eastern Hemisphere sales only I 135 155 175 200 1 286 TEMPERATURE RATING 135F/57°C 155°F/68°C 175°F/79C 200°1`/93C 286F/141°C SPRINKLER 1 NATURAL BRASS 4 WHITE POLYESTER 3 WHITE (RAL9010)* 9 CHROME PLATED 7 LEAD COATED Page 10 of 10 TFPI7I TABLEID PART NUMBER SELECTION SERIES TY-FRB PENDENT AND UPRIGHT Limited. Warranty Products manufactured by Tyco Fire & Building Products (TFBP) are war- ranted solely to the original Buyer for ten (10) years against defects in mate- rial and workmanship when paid for and properly installed and maintained under normal use and service. This warranty will expire ten (10) years from date of shipment by TFBP. No warranty is given for products or com- ponents manufactured by companies not affiliated by ownership with TFBP or for products and components which have been subject to misuse, improper installation, corrosion, or which have not been installed, maintained, modi- fied or repaired in accordance with ap- plicable Standards of the National Fire Protection Association, and/or the standards of any other Authorities Having Jurisdiction. Materials found by TFBP to be defective shall be either repaired or replaced, at TFBP's sole option. TFBP neither assumes, nor authorizes any person to assume for it, any other obligation in connection with the sale of products or parts of prod- ucts. TFBP shall not be responsible for sprinkler system design errors or inac- curate or incomplete information sup- plied by Buyer or Buyer's repre- sentatives. In no event shall TFBP be liable, in contract, tort, strict liability or under any other legal the ry, for incidental, indirect, special or consequential dam- ages, including but riot limited to labor charges, regardlessof whether TFBP was informed about the possibility of such damages, andi in no event shall TFBP's liability exFeed an amount equal to the sales pice, ticular purpose. This limited warrant sets forth the ex- clusive remedy for claims based on failure of or defect in products, materi- als or components, whether the claim is made in contra tort, strict liability or any other legal theory. This warranty will aply to the full ex- tent permitted by lay. The invalidity, in whole or part, of any portion of this warranty will not affect the remainder. hen placing an order, indicate the II product name. Refer to the Price st for complete listing of Part Num- ntact your local distributor for avail- lity. iprinkler Assemblies with NPT 'hread Connections: pecify: (Specify Model/SIN), Quick esponse, (specify K-factor), (specify ?mperature rating), Series TY-FRB specify Pendent or Upright) Sprinkler ,ith (specify type of finish or coating), IN (specify from Table D). ecessed Escutcheon: pecify: Style (10, 20, 30, or 40) Re- essed Escutcheon with (specify*) fin- h, P/N (specify*). Refer to Technical Data Sheet TFP770 nkler Wrench: ify: W-Type 6 Sprinkler Wrench, 56-000-6-387. ify: W-Type 7 Sprinkler Wrench, 56-850-4-001. TYCO FIRE & BUILDING PRODUCTS, 451 NorthCannon Avenue, Lansdal, Pennsylvania 19446 \ Fire Prot tion D cuments / Ve sion Fir -S inki rc Project De /eSprinklErs PM: Carney II, Chet 44 -5203 Review Cycle Cycle 2 /Fire -Sprinklers (Sub it) THE CITY OF SAN f t I E G O Development Ser4ce s 1222 First Avenue, S a n D i e g o , C A 9 2 1 0 1 - 4 1 5 4 / . V / Package Copy \