Loading...
HomeMy WebLinkAbout2051 PALOMAR AIRPORT RD; ; AS160179; Permit12/16/21, 3:45 PM AS160179 Permit Data City of Carlsbad Sprinkler Permit Permit No: AS160179 2051 PALOMAR Job Address: Status: ISSUED AIRPORT RD Permit Type: SPRINK Applied 6/6/2016 Parcel No: 2130503900 Approved: 6/21/2016 Lot #: 0 Reference No.: Issued: 6/21/2016 PC #: Inspector: Project Title: HIGH MOON STUDIOS T.I. Applicant: TOTAL FIRE PROTECTION, INC STE. 244 1611-A S. MELROSE DR. VISTA, CA 760-525-4329 Owner: JCCE-PALOMAR L L C C/O JAMES COXETER 23554 OLD 44 DR MILLVILLE CA Fees d'I Fees ($) J - Total ($) Balance$ 303 0 L303____ 0----F- 1/1 MATERIAL DATA SUBMITTAL High Moon Studios 2051 Palomar Airport Road - Suite 100 Carlsbad, CA 92011 Page * Description Manufacturer 1-2 Pipe Allied Dyna-Thread Pipe 3-10 Fittings Tyco Ductile Iron Fittings 11-12 Mechanical Tee Tyco Fig 40-5 Strap Tee 13-19 Sprinkler Reliable F1FR56 Sprinkler 20-23 Sprinkler Reliable F1FR56 Sprinkler 24 Hanger Afcon Fig. 300 Ring Hanger 25 Hanger Afcori Fig 655 All Thread Rod 26-27 Attachment Sammy Wood Vertical Mount Total Fire Protection, Inc. 1611 A S. Melrose Dr. *244 Vista, CA 92081 (760)525-4329 fax (877) 724-4329 C16-955387 tfpjohnc©gmail.com AS 160179 2051 PALOMAR AIRPORT RD 1( DynalmiThread 0 Full Line Sch-40 Replacement Dyna-Thread offers the life expectancy of Sch40 with superior hydraulics and greater value. Dyna-Thread sprinkler pipe represents an engineering advancement for the sprinkler pipe industry. It combines the safety and longevity of traditional Sch-40 pipe with quality and superior hydraulic advantages. S Dyna-Thread's inside diameter is up to 3.6% larger than Sch-40 giving it superior hydraulics. And, when used in combination with Dyna-Flow pipe, down sizing often occurs. Dyna-Thread is fully listed and approved by UL, ULC, and FM for fire sprinkler applications. The life expectancy of Dyna-Thread and Sch40 are equal based on the calculated wall thicknesses per UL. The consistent quality of steel used to make Dyna-Thread facilitates smooth threading and lower maintenance costs. The exterior of Dyna-Thread is protected by a clean, durable mill coating for extended shelf life and easy paint application. ei Listed Approved Listed With its increased strength and lighter weight, Dyna-Thread reduces installation fatigue and is ideal for retro-fit applications. Corrosion Resistance Ratio (CRR) is a UL (Underwriters Laboratory) term for the estimated life expectancy of a pipe joint. This is based on the calculated wall thickness at the base of the first exposed thread, assumed to be the weakest point of the pipe length. Dyna- Thread and Sch-40 have the same calculated wall thicknesses at this point and are both assigned the same CRR of 1.00. The internal surface of all black Allied Tube & Conduit Fire Sprinkler pipe products up to 4.5000" in diameter is coated with our new Antibacterial Formula, "ABF". In scientific laboratory test, ABS proved to have superior resistance to microbial colonization of pipe walls, thereby delaying or possibly preventing the onset of Microbiologically Influenced corrosion (MIC) when the First Sprinkler System is first installed. More wall thickness at the thread (CRR=l .00) gives Dyna-Thread better life expectancy than lightwall threadable pipe joints. Unlike lightwall threadable pipe, Dyna-Thread has no thread gauge warning. Dyna-Thread is approved for standard hanger spacing (15 ft. O.C.), can be used as earthquake sway bracing, and is safe to use as drops. Dyna-Thread is safer to weld on. Dyna-Thread is more widely accepted than lightwall threadable where Sch-40 is specified. Super 40/Dyna-Thread pipe is manufactured to meet: ASTM A-135, Grade A and is in compliance with NFPA- 13. All sizes of Super 40/Dyna- Thread are rated at 300 psi working pressure. Super 40/Dyna-Thread is UL and ULC Listed for wet, dry deluge and pre-action sprinkler systems and FM Approved for use in wet systems. Super 40/Dyna-Thread can be "hot-dip" galvanized to meet FM requirement for dry systems. Super 40/Dyna-Thread is approved for all threaded couplings and welded outlets and is suitable for all roll-grooved, and plain-end fittings. (See listing information). Specifications NPS Nominal I.D. Wt. WI. (1120 Filled) Pcsl Wt/1.ift (21') WVLIft (24') Wt/Lift (25') In; mm In; mm Lbs/Ft;Kg/m Lbs/Ft;Kg/m Lift Lbs;Kg Lbs;Kg Lbs;Kg 1.080 1,330 1.75 70 1955 2234 232 25 27.4 2.0 2.60 70 887 1013 105 1W 1.408 1.870 2.54 51 2002 2288 2384 32 35.8 2.8 3.78 51 908 1038 108 11/2" 1.639 2.290 3.22 44 2115 2418 2511 40 41.6 3.4 4.79 44 959 1097 114 2.104 3.050 4.57 30 1921 2196 228 50 53.4 4.5 6.80 30 871 996 103 tqco/Flow Control Qr 16100 S. Lathrop' Harvey, IL 60426 cubed 11350 Norcom Rd. 'Philadelphia, PA 19154 TUBE &CONDUIT 2525 N. 27th Ave. 'Phoenix, AZ 85009 Customer Service: 1 (800) 882-5543 Fax 708-339-1806 S3 -3 Submittal Data Sheet Dyna Threade S Full Line Sch-40 Replacement Dyna-Thread sprinkler pipe represents an engineering advancement for the sprinkler pipe industry. It combines the safety and longevity of traditional Sch-40 pipe with quality and superior hydraulic advantages. Comparison to Schedule 40 Dyna-Threads inside diameter is up to 3.6% larger than Sch-40 giving it superior hydraulics. Also, when used in combination with Dyna-Flow pipe, down sizing often occurs. Dyna-Thread is fully listed and approved UL, ULC, and FM for fire sprinkler applications. The life expectancy of Dyna-Thread and Sch40 are equal based on the calculated wall thicknesses per UL. The consistent quality of steel used to make Dyna-Thread facilitates smooth threading and lower maintenance costs. The exterior of Dyna-Thread is protected by a clean, durable mill coating for extended shelf life and easy paint application. With its increased strength and lighter weight, Dyna-Thread reduces installation fatigue and is ideal for retro-fit applications. Corrosion Resistance Ratio (CRR) is a UL (Underwriters Laboratory) term for the estimated life expectancy of a pipe joint. This is based on the calculated wall thickness at the base of the first exposed thread, assumed to be the weakest point of the pipe length. Dyna-Thread and Sch-40 have the same calculated wall thicknesses at this point and are both assigned the same CRR of 1.00. Comparison to L.W.T. Pipe More wall thickness at the thread (CRR=l .00) gives Dyna-Thread better life expectancy than lightwall threadable pipe joints. Unlike lightwall threadable pipe Dyna-Thread has no thread gauge warning. Dyna-Thread is approved for standard hanger spacing (15 ft. O.C.), can be used as earthquake sway bracing, and is safe to use as drops. Dyna-Thread is safer to weld on than many zinc- coated lightwall threadable pipe products. Dyna-Thread is more widely accepted than lightwall threadable where Sch40 is specified. Stamp Here S Specifications & Approvals Super 40/ Dyna-Thread pipe is manufactured to meet: ASTM A 135, Grade A and is in compliance with NFPA-13. All sizes of Super 40/Dyna-Thread are rated at 300 psi working pressure. Super 40/ Dyna- Thread is UL and ULC Listed for wet, dry and pre-action sprinkler systems and FM Approved for use in wet systems. Super 40fDyna-Thread can be "hot-dip" galvanized to meet FM requirement for dry systems. Super 40/Dyna-Thread is approved for all threaded couplings and welded outlets and is suitable for all roll- grooved, and plain-end fittings. (See listing information). The internal surface of all black Fire Sprinkler pipe up to 4.5000" in diameter shall be coated with Allied Tube & Conduit Antibacterial Formula "ABF". Specifications NPS Nominal LO. WI. Wt. (1120 Filled) Pc WI/Lift (21') WtIUft (24') WI/Lilt (25' In; mm In; mm LbslFt; Kg/rn Lbs/Ft; Kg/rn Lift Lbs; Kg Lbs; Kg Lbs; Kg 1" 1.080 1.330 1.75 70 1955 2234 2327 25 27.4 2.0 2.60 70 887 1013 1051 1W 1.408 1.870 2.54 51 2002 2288 2384 32 35.8 2.8 3.78 51 908 1038 108 11/2, 1.639 2.290 3.22 44 2115 2418 2519 40 41.6 3.4 4.79 44 959 1097 114 2' 2.104 3.050 4.57 30 1921 2196 228 50 53.4 4.5 6.80 30 871 996 1034 American Tube and Pipe was acquired by Allied Tube and Conduit on February I, 1997. The engineered lightwall and standard wall family of products although they have different names are the same in all respects with regard to strength, weight, bundle count, listings and approvals. For example, Dyna-Flow and Super Flo are the same product as are Dyna Thread and Super 40. XL is manufactured L UO FM U LC with Exterior galvanized coating. BLT is manufactured with Black lacquer coating. Listed Approved Listed Project: Sprinkler Contractor: Date: is Engineer: Locations: S3-4 Specification Reference: System Type: Comments: (II) tqC0 Fire & Building IProducts Technical Services: Tel: (800) 381-9312/ Fax: (800)791-5500 Pipe Fittings NPT Threaded, Ductile Iron General Description The Tycoe Series 800 Threaded Pipe Fittings and California Tees & Elbows are manufactured from ductile iron. They are stronger and more corrosion resistant than cast iron fittings. The additional strength is provided by the ductile properties and by adding mag- nesium while the iron is being poured into the final cast shape. Although lighter than standard cast iron, the fit- tings have an added advantage of be- ing less susceptible to cracking due to their added strength. The Series 800, California, and Figure 719 Threaded Pipe Fittings are a re- designation for the Central Series 800, California, and Figure 719 Threaded Pipe Fittings. WARNINGS The Threaded Pipe Fittings described herein must be installed and main- tained in compliance with this docu- ment, as well as with the applicable standards of the National Fire Pro- tection Association, in addition to the standards of any other authorities hav- ing jurisdiction. Failure to do so may impair the performance of these devices. The owner is responsible for maintain- ing their fire protection system and de- vices in proper operating condition. The installing contractor or sprinkler manufacturer should be contacted with any questions. Technical Data Approvals: UL Listed and FM Approved Maximum Working Pressure: Series 800 and California Fittings: 250 psi (17,2 bar) Figure 719 Plug: 250 psi (17,2 bar) Page 1 of 10 Material: Series 800 and California Fittings: Ductile Iron Figure 719 Plug: Cast Iron Pipe Thread: NPT per ANSI 81.20.1 Installation Apply Teflont tape or high quality pipe joint compound on male pipe threads and tighten two to three turns beyond hand tight. NOTE Installers who have not used ductile iron threaded fittings should be in- structed that the fittings are stron- ger than the pipe and overtightening the fitting can create leaks and cause damage to pipe threads. In general, there is about one-half turn difference between cast iron and ductile iron fit- tings. Apply Teflon tape or high qual- ity pipe joint compound on the male pipe threads and tighten two to three turns beyond hand tight. If an auto- matic make-on machine is being used, please exercise caution in setting the machine to the proper parameters pri- or to tightening fittings onto the male pipe threads. Limited Warranty Products manufactured by Tyco Fire & Building Products (TFBP) are war- ranted solely to the original Buyer for ten (10) years against defects in mate- rial and workmanship when paid for and properly installed and maintained under normal use and service. This warranty will expire ten (10) years from date of shipment by TFBP. No warran- ty is given for products or components manufactured by companies not af- filiated by ownership with TFBP or for products and components which have been subject to misuse, improper in- stallation, corrosion, or which have not been installed, maintained, modified or repaired in accordance with applicable JANUARY, 2008 Standards of the National Fire Protec- tion Association, and/or the standards of any other Authorities Having Juris- diction. Materials found by TFBP to be defective shall be either repaired or re- placed, at TFBP's sole option. TFBP neither assumes, nor authorizes any person to assume for it, any other ob- ligation in connection with the sale of products or parts of products. TFBP shall not be responsible for sprinkler system design errors or inaccurate or incomplete information supplied by Buyer or Buyer's representatives. In no event shall TFBP be liable, in contract, tort, strict liability or under any other legal theory, for incidental, indirect, special or consequential dam- ages, including but not limited to labor charges, regardless of whether TFBP was informed about the possibility of such damages, and in no event shall TFBP's liability exceed an amount equal to the sales price. The foregoing warranty is made in lieu of any and all other warranties. ex- press or implied, including warranties of merchantability and fitness for a particular DUrpose. This limited warranty sets forth the ex- clusive remedy for claims based on failure of or defect in products, materi- als or components, whether the claim is made in contract, tort, strict liability or any other legal theory. This warranty will apply to the full ex- tent permitted by law. The invalidity, in whole or part, of any portion of this warranty will not affect the remainder. Ordering Procedure When placing an order, indicate the full product name. Please specify the quantity, figure number, wall thickness, and size. tregistered trademark of E. I. du Pont de Nemours and Company or its affiliates. TFPI7IO Page 2of 10 TFPI7I0 Nominal Pipe Figure 813 Size ANSI A Approx. Inches Inches Weight Part ON (mm) Lbs. Number (kg) 1/2 1.13 0.22 86780 DN15 (28,7) (0,09) 3/4 1.31 0.33 86781 0N20 (33,3) (0,15) 1 1.50 0.48 86280 0N25 (38,1) (0,21) 1-1/4 1.75 0.73 86281 DN32 (44,5) (0,33) 1-1/2 1.94 0.93 86282 0N40 (49,3) (0,42) 2 2.25 1.55 86283 0N50 (57,1) (0,70) 2-1/2 2.69 2.70 86782 0N65 (68,3) (1,22) 0 fl fl FIGURE 811 FIGURE 813 900 ELBOW 450 ELBOW Figure 811 B Approx. A B Inches Weight Part Inches Inches (mm) Lbs. Number (mm) (mm) (kg) 0.56 0.24 86206 0.88 0.38 (14,2) (0,11) (22,4) (9,7) 0.75 0.40 86205 1.00 0.44 (19,0) (0,18) (25,4) (11,2) 0.81 0.64 86200 1.13 0.81 (20,6) (0,29) (28,7) (20,6) 1.06 0.95 86201 1.31 0.63 (26,9) (0,43) (33,3) (16,0) 1.19 1.24 86202 1.44 0.69 (30,2) (0,56) (36,6) (17,5) 1.50 1.74 86203 1.68 0.94 (38,1) (0,79) (42,7) (23,9) 1.56 3.28 86204 1.94 1.00 (39,6) (1,49) (49,3) (25,4) TABLE I NOMINAL DIMENSIONS FIGURES 811 & 813 TFPI7IO Page 3 of 10 TB FIGURE 812 900 REDUCING ELBOW Nominal Pipe Figure 812 Size ANSI A B C D Approx. Weight Part Inches Inches Inches Inches Inches Lbs. DN (mm) (mm) (mm) (mm) Number (kg) 3/4x1/2 1.19 1.19 0.63 0.63 0.33 86342 DN20 x 15 (30,2) (30,2) (16,0) (16,0) (0,15) 1 x 1/2 1.25 1.38 0.56 0.81 0.44 86210 DN25 x 15 (31,8) (35,1) (14,2) (20,6) (0,20) 1 x3/4 1.38 1.44 0.69 0.88 0.53 86211 0N25 x 20 (35,1) (36,6) (17,5) (22,4) (0,24) 1-1/4x1/2 1.31 1.50 0.63 0.94 0.64 86212 0N32 x 15 (33,3) (38,1) (16,0) (23,9) (0,29) 1-1/4x3/4 1.44 1.63 0.75 1.06 0.75 86213 DN32 x 20 (36,6) (41,4) (19,0) (26,9) (0,34) 1-1/4x1 1.56 1.68 0.88 1.00 0.77 86214 DN32 x 25 (39.6) (42,7) (22,4 (25,4) (0,35) 1-1/2 x 3/4 1.50 1.75 0.75 1.19 0.95 86221 DN40 x 20 (38,1) (44,4) (19,0) (30,2) (0,43) 1-1/2 x 1 1.63 1.81 0.88 1.13 0.99 86215 DN40x25 (41,4) (46,0) (22,4) (28,7) (0145) 1-1/2x1-114 1.81 1.88 1.13 1.19 1.14 86216 DN4O x 32 (46,0) (47,8) (28,7) (30,2) (0,52) 2x3/4 1.63 1.94 0.88 1.38 1.39 86217 DN50x20 (41,4) (49,3) (22,4) (35,1) (0,63) 2x1 1.75 2.06 2.00 1.31 1.58 86218 DN50x25 (44,4) (52,3) (50,8) (33,3) (0,72) 2 x 1-1/2 2.00 2.19 1.25 1.44 1.67 86220 DN50 x 40 (50,8) (55,6) (31,8) (36,6) (0,76) 2-1/2 x 2 2.38 2.63 1.25 1.88 3.01 86262 DN65 x 50 (60,5) (66,8) 1 (31,8) 1 (47,8) (1,36) TABLE 2 NOMINAL DIMENSIONS FIGURE 812 0 S n TFPI7I0 Page 5of 10 0 S Nominal Pipe Size A Approx. ANSI Inches Inches Weight Part DN (mm) Lbs. Number (kg) 1/2 1.13 0.18 72779 0N15 (28,7) (0,08) 3/4 1.31 0.26 72778 DN20 (33,3) (0,11) 1 1.50 0.44 72755 DN25 (38,1) (0,20) 1-1/4 1.75 0.54 72754 DN32 (44,4) (0,24) 1-1/2 1.94 0.71 72753 DN40 (49,3) (0,32) 2 2.25 1.15 72752 DN50 (57,1) (0,52) 2-1/2 2.69 2.29 12758 0N65 (68,3) (1,04) _A7 rJiJ1 FIGURE 814 FIGURE 818 IRON TEE STRAIGHT COUPLING 4.55 TABLE 4 NOMINAL DIMENSIONS FIGURES 814 & 818 Figure 814 Figure 818 B Approx. A B Inches Weight Part Inches Inches (mm) Lbs. Number (mm) (mm) (kg) 0.56 0.33 86340 1.38 0.31 (14,2) (0,15) (35,1) (7,9) 0.75 0.50 86341 1.63 0.56 (19,0) (0,23) (41,4) (14,0) 0.81 0.85 86230 1.75 0.38 (20,6) (0,38) (44,4) (9,7) 1.06 1.30 86231 2.00 0.56 (26,9) (0,59) (50,8) (14,0) 1.19 1.63 86232 2.19 0.75 (30,2) (0,74) (55,6) (19,0) 1.50 2.63 86233 2.63 1.13 (38,1) (1,19) (66,8) (28,7) 1.56 86234 3.00 0.75 (39,6) (2,06) (76,2) (19,0) TFPI7I0 Page 6of 10 S 0 S S Page 7 of 10 TFPI7IO FIGURE 815 REDUCING TEE Nominal Pipe Size Figure 815 A B C D E F Approx. ANSI Inches Inches Inches Inches Inches Inches inches Weight Part DN (mm) (mm) (mm) (mm) (mm) (mm) Lbs. Number (kg) 1-112x1-1/4x112 1.44 1.31 1.69 0.69 0.63 1.13 1.03 DN40x32x15 (36,6) (33,3) (42,9) (17,5) (16,0) (28,7) (0,47) 86257 1-112x1-114x314 1.50 1.44 1.75 0.75 0.75 1.19 1.10 DN40x32x20 (38,1) (36,6) (44,5) (19,0) (19,0) (30,1) (0,50) 86258 1-1/2x1-1/4x1 1.63 1.56 1,81 0.88 0.88 1.13 1.31 86259 0N40x 32 x 25 (41,4) (39,7) (46,0) (22,4) (22,4) (28,7) (0,59) 1-1/2x1-114x2 2.19 2.13 2.00 1.44 1.44 1.25 1.94 86260 DN40 x 32 x 50 (55,6) (54,1) (50,8) (36,6) 1 (36,6) (57,1) (0,88) 1-1/2x1-1/2x112 1.44 1.44 1.69 0.69 0.69 1.13 1.14 86261 DN40 x 40 x 15 (36,6) (36,6) (42,9) (17,5) (17,5) (28,7) (0,52) 1-1/2x1-1/2x314 1.50 1.50 1.75 0.75 0.75 1.19 1.23 86262 DN40 x 40 x 20 (38,1) (381) (44,4) (19,0) (19,0) (30,1) (0,56) 1-1/2x1-1/2x1 1.63 1.63 1.81 0.88 0.88 1.13 1.38 86263 DN40x40x25 (41,2) (41,2) (46,0) (22,4) (22,4) (28,7) (0,62) ______ 1-112x1-112x1-1/4 1.81 1.81 1.88 1.06 1.06 1.19 1.50 86264 DN40 x 40 x 32 (46,0) (46,0) (47,6) (27,0) (27,0) (30,1) (0,68) 1-1/2x1-112x2 2.19 2.19 2.00 1.44 1.44 1.25 2.00 86265 DN40 x 40 x 50 (555) (55,5) (50,8) (36,6) (36,6) (31,7) (0.91) 2x1 x2 2.25 2.00 2.25 1.50 1.31 1.50 2.18 86266 DN50 x 25 x 50 (57,2) (50,8) (57,2) (38,1) (33,3) (38,1) (0,99) _______ 2x1-114x2 2.25 2.13 2.25 1.50 1.44 1.50 2.31 86267 DN50 x 32 x 50 (57,2) (54,1) (57,2) (38,1) (36,6) (38,1) 2x1-1/2x1/2 1.50 1.44 1.88 0.75 0.69 1.31 1.50 86268 DN50 x 40 x 15 (38,1) (36,6) (47,8) (19,0) (17,5) (33,3) (0,68) 2x1-1/2x314 1.63 1.50 1.94 0,88 0.75 1.38 1.61 86269 DN50 x 40 x 20 (41,4) (38,1) (49,3) (22,4) (19,0) (35,0) (0,73) 2x1-1/2x1 1.75 1.63 2.00 1.00 0.88 1.31 1.65 86270 DN50x40x25 (44,5) (41,4) 1 (50,8) (25,4) 1 (22,4) (33,3) (0,75) 2x1-112x1-112 2.06 1.94 1.19 1.44 2.03 86272 DN50 x 40 x 40 (52,4) (49,2) (55,5) (30,2) (36,6) (0,92) 2x1-1/2x2 2.25 2.19 2.50 1.44 1.50 2.37 86273 DN50 x 40 x 50 (57,1) (55,5) (63,5) 2.19 t008088 (36,6) (38,1) (1,07) 2x2x112 1.50 1.50 1.88 0.75 1.31 1.50 86222 DN50 x 50 x 15 (38,1) (38.1) (47,8) (19,0) (33,3) (0,68) 2x2x3/4 1.63 1.63 1.94 0.88 1.38 1.67 86223 DN50x50x20 (41,4) (41,4) (49,3) (22,4) (22,4) (35,0) (0,76) 2x2x1 1.75 1.75 2.00 1.00 1.00 1.31 1.91 86224 DN50 x 50 x 25 (44,5) (44,5) (50.8) (25,4) (25,4) (33,3) (0,86) 2x2x1-1/4 1.88 1.88 2.13 1.13 1.13 1.44 2.05 86225 0N50 x 50 x 32 (47,8) (47,8) (54,1) (28.7) (28,7) (36,6) (0,93) 2x2x1-112 2.00 2.00 2.19 1.25 1.25 1.50 2.11 86226 DN50x50x40 (50,8) (50,8) (55,6) (31,8) I (31,8) (38,1) (0,96) 2x2x2-112 2.63 2.63 2.38 1.75 1.88 1.44 3.67 86227 DN50 x 50 x 65 (66,8) (66,8) (60,5) (44,5) (47,8) (36,6) (1,66) 2-1/2x2x3/4 1.75 1.63 2.31 0.63 0.88 1.75 2.22 86274 0N65 x 50 x 20 (44,5) (41,4) (58,7) (15,9) (22,4) (44,5) (1,01) TABLE 5(2 0F2) NOMINAL DIMENSIONS FIGURE 815 Page 8 of 10 TFPI7IO S IIll!I1 iiiiii1 S FIGURE 820 FIGURE 830 FIGURE 719 CAP BRASS SEAT UNION PLUG Nominal Pipe Figure 820 Figure 830 Figure 719 Size ANSI A Approx. A B Approx. A Approx. Inches Inches Weight Part Inches Inches Weight Part Inches Weight Part DN (mm) Lbs. Number (mm) (mm) Lbs. Number (mm) Lbs. Number (kg) (kg) (kg) 1/2 0.68 0.15 72776 1.88 0.81 0.47 86207 0.94 0.10 86292 0N15 (22,4) (0,06) (47,8) (20,6) (0,21) (23,9) (0,04) 3/4 1.00 0.22 72777 2.00 0.94 0.66 86275 1.13 0.18 86293 DN20 (25,4) (0110) (50,8) (23,9) (0,30) (28.7) (0,08) 1 1.18 0.33 72824 2.19 0.81 1.08 86276 125 0.28 86294 0N25 (30,0) (0115) (55,6) (20,6) (0149) (31,7) (0,13) 1-1/4 1.31 0.54 72756 2.50 1.06 1.54 86277 1.38 0.50 86295 0N32 (33,3) (0,24) (63,5) (26,9) (0,70) (35,1) (0,23) 1-1/2 1.38 0.68 72822 2.63 1.19 2.03 86278 1.44 0.70 86296 0N40 (35,1) (0,31) (66,8) (302) (0,92) (36,6) (0,32) 2 1.50 0.96 72823 3.13 1.63 3.15 86279 1.50 0.90 86297 DN50 (38,1) (0,43) (79,5) (41,4) (1,43) (38,1) (0,41) 2-1/2 1.75 1.80 72825 - - - - - - - DN65 (44,5) (0,82) TABLE 6 NOMINAL DIMENSIONS FIGURES 820,830 & 719 S TFPI7IO Page 9 of 10 LLr Jj S FIGURE 825 FIGURE 827 FIGURE 816 EXTENSION PIECE HEX BUSHING REDUCING COUPLING Nominal Pipe Figure 825 Figure 827 Figure 816 Size Extension Piece Hex Bushing Reducing Coupling A Approx. A Approx. A B Approx. ANSI Inches Inches Weight Part Inches Weight Part Inches Inches Weight Part DN (mm) Lbs. Number (mm) Lbs. Number (mm) (mm) Lbs. Number (kg) (kg) (kg) 1/2x1/2 1.50 0.20 72751 - - - - - - - DN15 x 15 (38,1) (0,09) 1/2 x 1/2 2.00 0.27 72980 - - - - - - - DN15 x 15 (50,8) (0.12) 3/4x3/4 1.50 0.22 72981 - - - - - - - 0N20 x 20 (38,1) (0,10) 3/4 x 3/4 2.00 0.31 73982 - - - - - - - 0N20 x 20 (50,8) (0,14) 3/4 x 1/2 1.75 0.69 0.38 86772 DN20 x 15 - - - - - (43,2) (17,5) (0,17) 1 x 1/2 1.06 0.22 72726 1.69 0.50 0.38 86228 0N25 x 15 - (26,9) (0,10) (42,9) (12,7) (0,17) 1 x3/4 1.06 0.18 72762 1.75 0.50 0.53 86229 0N25 x 20 - - - (26,9) (0,08) (43,2) (12,7) (0,24) 1-1/4x1 1.19 0.31 72763 - - - - 0N32 x 25 - - - (30,2) (0,14) 1-1/2x1 1,25 0.53 72757 - - - - DN40 x 25 - - - (31,7) (0.24) 1-1/2x1-1/4 1.25 0.35 72764 - - - - DN40 x 32 - (31,7) (0,10) 2x1 1.38 0.75 72759 - - - - DN50 x 25 - - (35,1) (0,34) 2x1-1/4 1.38 0.69 72761 - - - - DN50 x 32 - - - (35,1) (0.31) 2 x 14/2 1.38 0.62 72775 - - - - DN50x40 - - (35,1) (0,28) TABLE 7 NOMINAL DIMENSIONS FIGURE 825,827 & 816 8 See Fire Protection Submittal Sheet for Pressure Rating and Listing/Approval Information I tqC0 /Fire & Building I Products Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500 www.tyco-fire.com Grinnell Grooved Fire Protection Products Figure 40-5 Strap General Description The Figure 40-5 Strap is an economical alternative to welded pipe outlets on steel pipe. The Figure 40-5 Strap may be used with full lengths of pipe and eliminates threading and welding, decreasing waste and installation time. The 40-5 Strap may be used in wet, dry pipe and deluge systems. WARNING The Figure 40-5 Strap described herein must be installed and maintained in compliance with this document, as we/fas withtheapplicable standards of the National Fire Protection Association, in addition to the standards of any otherautho rities ha ving jurisdiction. Failure to do so mayimpair the performance of this device. The owner is responsible for maintaining their fire protection system and devices in proper operating condition, The installing contractor or sprinklermanufacturershould be contacted with any questions. Technical Data Figure: 40-5 Outlet: Threaded Approvals: UL, FM, ULC, and VdS; See Fire Protection Submittal Sheet for exact Listing /Approval information. Page 1 of 2 Housing: Ductile iron conforming to ASTM A-536, Grade 65-45-12 Protective Coatings: 'Clear rust inhibitive coaling 'Zinc electroplated conforming to ASTM 6-633, Type Ill Service 2 (optional) U-Bolt: Carbon steel conforming to ASTM A-307, Grade A, Zinc electroplated Nuts: Carbon steel conforming to ASTM A-307, Grade A, Zinc electroplated Gasket: (specify when ordering) Grade "E" EPDM green color code. (See Data Sheet 1FP1895 for aid in selecting proper gasket) Ordering Procedure When placing an order, indicate the full product name. Please specifythe quantity, figure number, type of gasket, Grade "E" EPOM, and size. Grinnell Grooved Piping Products, valves, accessories and other products are available throughoutthe U.S., Canada, and internationally, through a network of distribution centers. You may write directly or call 215-362-0700 for the distributor nearest you. Care and Maintenance The owner is responsible for the inspection, testing, and maintenance of their fire protection system and devices in accordance with the applicable standards of the National Fire Protection Association (e.g., NFPA 25), in addition to the standards of any authority having jurisdiction. The installing contractor or product manufacturer should be contacted relative to any questions. Any impairment must be immediately corrected. It is recommended that automatic sprinkler systems be inspected, tested, and maintained by a qualified Inspection Service. September 2004 Limited Warranty Products manufactured by Tyco Fire Products are warranted solely to the original Buyer for ten (10) years against defects in material and workmanship when paid forand property installed and maintained under normal use and service. This warranty Will expire ten (10) years from date of shipment by Tyco Fire Products. No warranty is given for products or components manufactured by companies not affiliated byownershipwith Tyco Fire Products orfor products and components which have been subject to misuse, im proper installation, corrosion, orwhich have not been installed, maintained, modified or repaired in accordance with applicable Standards of the National Fire Protection Association (NFPA), and/or the standards of any otherAuthorities Having Jurisdiction. Materials found by Tyco Fire Products to be defective shall be either repaired or replaced, at Tyco Fire Products' sole option. Tyco Fire Products neither assumes, nor authorizes any person to assumeforit, any other obligation inconnectionwith the sale of products or parts of products. Tyco Fire Products shall notbe responsibleforsprinklersystem designerorsorinaccurateorincompleteinformation supplied by Buyer or Buyers representatives. IN NO EVENT SHALL TYCO FIRE PRODUCTS BE LIABLE, IN CONTRACT, TORT, STRICT LIABILITY OR UNDER ANY OTHER LEGAL THEORY, FOR INCIDENTAL, INDIRECT, SPECIAL OR CONSEQUEN11ALDAMAGES, INCLUDING BUTNOT LIMITED TO LABOR CHARGES, REGARDLESS OF WHETHER1YCO FIREPRODUCTS WAS INFORMED ABOUT THE POSSIBILITY OF SUCH DAMAGES, AND IN NO EVENTSHALLTYCO FIRE PRODUCTS' LIABILITY EXCEED AN AMOUNT EQUAL TO THE SALES PRICE. a,? (B TFPI 720 Pipe Nominal Dimensions Hole Net A B C 0 Size Size Wt. Run x Inches Inches Inches Inches Inches Lbs. Branch mm mm mm mm mm Kg. 11/40 X 11211 2.00 1.50 3.50 1.20 1/io 0.84 50.8 38.1 1 88.9 30.5 30.2 0.4 11/40 X 3/40 2.00 1.50 1 3.50 1.20 1/i 0.88 50.8 38.1 88.9 30.5 30.2 0.4 11/40 X V 2.31 1.68 3.50 1.20 1/18 1.13 58.7 42.7 88.9 30.5 30.2 0.5 11/21 X 1/311 2.12 1.62 3.50 1.32 11/16 0.84 53.8 41.1 88.9 33.5 30.2 0.4 11/20X3/4° 2.12 1.62 3.50 1.32 0.88 53.8 41.1 88.9 33.5 30.2 0.4 1V2" X 111.2.43 1.80 3.50 1.32 1/l6 1.13 61.7 45.7 88.9 33.5 30.2 0.5 2°x'/2 2.36 1.86 3.74 1.55 1/i 0.88 59.9 47.2 95.0 39.4 30.2 0.4 2 x 3/411 2.36 1.86 3.74 1.55 1/1 0.95 59.9 472 95.0 39.4 30.2 0.4 20x 10 2.67 2.04 3.74 1.55 1/1 1.16 67.8 51.8 95.0 39.4 30.2 0.5 21/211 X1/2" 2.61 2.11 4.25 1.80 1/1 0.90 66.3 53.6 108.0 45.7 30.2 1 0.4 2V20 X3/4" 2.61 2.11 4.25 1.80 1/l6 0.99 66.3 53.6 108.0 45.7 30.2 0.4 21/2 x 1 2.92 2.29 4.25 1.80 1/i 1.21 74.2 58.2 108.0 45.7 30.2 0.5 Item Description 1 Housing 2 Gasket 3 Flanged Nut 4 U-Bolt Fitting Size Equivalent Length (1 inch pipe) 1'/4°X it. 8 1'/20 X 1° 6 20 x10 6 21/20 x 1' 4 The friction loss for these outlets is specified in equivalent length of 1 inch Schedule 40 (C=120) pipe. C Page 2 of 2 TFP1 720 Figure 40-5 Strap The 1 inch outlets can be used with a nipple leading Note: Outlet threads conforming to ISO 7-1 are available, contact directly to a sprinkler. These fittings should be used Tyco Fire Products. for hydraulically calculated systems only. (:12) General Notes: It is the Designer's responsibility to select products suitable for the Intended service and to ensure IS that pressure ratings and performance data is not exceeded. Always read and understand the installation 9001 instructions (11-1-1000). Never remove any piping component or correct or modify any piping deficiencies without first depressurizing and draining the system. Material and gasket selection should be verified lobe compatible for the specific application. . Certified Company TYCO FIRE PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19946 Printed U.S.A. tqCU Fire & Building IlProducts Technical Services: Tel: (800) 381-9312/ Fax: (800) 791-5500 Series TY-FRB - 2.8, 4.2, 5.6, and 8.0 K-factor Upright, Pendent, and Recessed Pendent Sprinklers Quick Response, Standard Coverage General Description The Tyco® Series TY-FRB, 2.8, 4.2, 5.6, and 8.0 K-factor, Upright and Pen- dent Sprinklers described in this data sheet are quick response - standard coverage, decorative 3 mm glass bulb type spray sprinklers designed for use in light or ordinary hazard, commercial occupancies such as banks, hotels, shopping malls, etc. The recessed version of the Series TY-FRB Pendent Sprinkler, where ap- plicable, is intended for use in areas with a finished ceiling. It uses either a two-piece Style 10 (1/2 inch NPT) or Style 40 (3/4 inch NPT) Recessed Es- cutcheon with 1/2 inch (12,7 mm) of recessed adjustment or up to 3/4 inch (19,1 mm) of total adjustment from the flush pendent position, or a two-piece Style 20 (1/2 inch NPT) or Style 30 (3/4 inch NPT) Recessed Escutcheon with 1/4 inch (6,4 mm) of recessed adjust- ment or up to 1/2 inch (12,7 mm) of total adjustment from the flush pen- dent position. The adjustment pro- vided by the Recessed Escutcheon re- duces the accuracy to which the fixed pipe drops to the sprinklers must be cut. Corrosion resistant coatings, where applicable, are utilized to extend the life of copper alloy sprinklers beyond that which would otherwise be ob- IMPORTANT Always refer to Technical Data Sheet TFP 700 for the "INSTALLER WARNING" that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and in- stallation can permanently damage a sprinkler system or its compo- nents and cause the sprinkler to fail to operate in a fire situation or cause it to operate prematurely. Page 1 of 10 tamed when exposed to corrosive at- mospheres. Although corrosion resis- tant coated sprinklers have passed the standard corrosion tests of the appli- cable approval agencies, the testing is not representative of all possible cor- rosive atmospheres. Consequently, it is recommended that the end user be consulted with respect to the suitability of these coatings for any given corro- sive environment. The effects of ambi- ent temperature, concentration of chemicals, and gas/chemical velocity, should be considered, as a minimum, along with the corrosive nature of the chemical to which the sprinklers will be exposed. An intermediate level versions of the Series TY-FRB Pendent Sprinklers are detailed in Technical Data Sheet TFP356, and Sprinkler Guards are de- tailed in Technical Data Sheet TFP780 WARNINGS The Series TY-FRB Sprinklers de- scribed herein must be installed and maintained in compliance with this document, as well as with the applica- ble standards of the National Fire Pro- tection Association, in addition to the standards of any other authorities hav- ing jurisdiction. Failure to do so may impair the performance of these de- vices. The owner is responsible for maintain- ing their fire protection system and de- vices in proper operating condition. The installing contractor or sprinkler manufacturer should be contacted with any questions. AUGUST, 2007 0 ModeliSprinkler Identification Numbers TYII3I - Upright 2.8K, 1/2"NPT TY1231 - Pendent 2.81K, 1/2"NPT 1Y2131 - Upright 4.21K, 1/2"NPT TY2231 - Pendent 4.21K. 1/2"NPT ITY3131 - Upright 5.61K, 112"NPT 11Y3231 - Pendent 5.61K. 112"NPT 1Y4131 - Upright 8.0K, 3/4"NPT TY4231 - Pendent 8.0K, 314"NPT 1Y4831- Upright 8.0K, 1/2"NPT TY4931- Pendent 8,0K, 112"NPT (B TFPI7I UPRIGHT CROSS SECTION L U2 FLAT FLATS 2-718" (73,0 mm) DIA. -1 RECESSED PENDENT T__ 2-3/16" \ (55,6 mm) 1-1/2" (38,1 mm) SSP DEFLECTOR * PENDENT 5 4 N i 7/16" (11,1 mm) NOMINAL I MAKE-IN - 2-3/16" P (55,6 mm) 1/2"NPT I TFPI7I Page 3 of 10 I ESCUTCHEON PLATE SEATING SURFACE 7/16j(11,1 mm) STYLE 100r20 NOMINAL RECESSED NPT IV AKEIN ESCUTCHEON SSU * DEFLECTOR - Frame 3 -Sealing 4 - Bulb 6 - Deflector 2 - Button Assembly 5-Compression Screw * Temperature rating is indicated on deflector or adjacent orifice seat on frame. FIGURE 3 QUICK RESPONSE SERIES TY-FRB UPRIGHT (TY3131) AND PENDENT (TY3231) SPRINKLERS 5.6 K-FACTOR, 1/2 INCH NPT SSU * DEFLECTOR ESCUTCHEON 1/2' (12,7 mm) PLATE SEATING 314" , NOMINAL SURFACE NPT MAKE-IN SSP DEFLECTOR* 2-7/8" PENDENT REC.& STYLE 30or40 RECESSED ESCUTCHEON ~DIA k) 3/4" NPT PENDENT UPRIGHT i, u lp 1/2" 11 MAKE-IN I 2-1/4" (57,2 mm) CROSS SECTION 1 - Frame 3 - Sealing - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to 2 - Button Assembly 5 - Compression orifice seat on frame. Screw FIGURE 4 QUICK RESPONSE SERIES TY-FRB UPRIGHT (TY4131) AND PENDENT (TY4231) SPRINKLERS 8.0 K-FACTOR, 3/4 INCH NPT ( D 0 Page 4oflO TFPI7I 7/16 (11,1 mm) NOMINAL SSU 12 MAKE-IN DEFLECTOR NIPT 2-1/4' t IlV' II 'NR 2-3/16" (57,2 mm) (k'r-'-fl . !lI_1LiI 1-9/16" WRENCH 2 (39,7 mm) FLATS I 3 SP* 1 EFLECTOR CROSS PE NT UPRIGHT SECTION 1 - Frame 3 - Sealing 4 ulb 6- Deflector * Temperature rating is indicated on deflector or adjacent to 2 - Button Assembly 5 - Compression orifice seat on Irame. Screw FIGURE 5 UICK RESPONSE SERIES TY-FRB UPRIGHT (TY4831) AND PENDENT (TY4931) SPRINKLERS 8.0 K-FACTOR, 1/2 INCH NPT S Technical Data Approvals UL and C-UL Listed. FM, LPCB, and NYC Approved. (Refer to Table A and B for complete approval information including corro- sion resistant status.) Maximum Working Pressure Refer to Table C. Discharge Coefficient K = 2.8 GPM/psil/2 (40,3 LPM/barl/2) K = 4.2 GPM/psi1/2 (60,5 LPM/bari/2) K = 5.6 GPM/psil/2 (80,6 LPM/bar112) K = 8.0 GPM/psill2 (115,2 LPM/barl') Temperature Ratings Refer to Table A and B Finishes Sprinkler: Refer to Table A and B. Recessed Escutcheon: White Coated, Chrome Plated, or Brass Plated. Physical Characteristics Frame .............Bronze Button .........Brass/Copper Sealing Assembly .......... Beryllium Nickel w/Teflont Bulb ...............Glass Compression Screw .....Bronze Deflector .......Copper/Bronze Bushing (K2.8) .......Bronze Operation The glass Bulb contains a fluid which expands when exposed to heat. When the rated temperature is reached, the fluid expands sufficiently to shatter the glass Bulb, allowing the sprinkler to activate and water to flow. Design Criteria The Series TY-FRB Pendent and Up- right Sprinklers are intended for fire protection systems designed in ac- cordance with the standard installation rules recognized by the applicable Listing or Approval agency (e.g., UL Listing is based on the requirements of NFPA 13, and FM Approval is based on the requirements of FM's Loss Pre- vention Data Sheets). Only the Style 10, 20, 30, or 40 Recessed Escutch- eon, as applicable, is to be used for recessed pendent installations. Page 6 of 10 TFPI7I SPRINKLER FINISH (See Note 8) K TYPE TEMP. BULB LIQUID NATURAL BRASS I CHROME PLATED WHITE*" 1POLYESTER LEAD COATED - 5.6 1/2" PENDENT (TY3231) and 135"F/57"C Orange 12,3,4,5,6,7 1,2,3,5 I155"F/68"C Red 175°F/79"C Yellow UPRIGHT (1Y3131) 200°F/93°C Green 286°F/141"C Blue NPT 135"F/57°C Orange 1,2,4,5 N/A RECESSED ENT 31)* e 10 LF I155°F/68°C Red 175°F/79"C Yellow 200"F/93"C Green 135"F/57°C Orange 1,2,3,4,5 N/A RECESSED PENDENT (TY3231) Figure 11 155"F/68°C Red 175°F/79°C Yellow 200°F/93°C Green - 8.0 3/4" PENDENT (1Y4231) and UPRIGHT ('l"t'4131) 135°F/57"C Orange 1,2, 3,4,5, 6, 7 1, 2,5 155"F/68°C Red 175"F/79"C Yellow 200"F/93"C Green 286"F/141°C Blue NPT RECESSED PENDENT (TY4231)" Figure 12 135"F/57C Green 1,2,4,5 N/A 155"F168"C Orange 175"F/79"C Red 200"F/93"C Yellow RECESSED PENDENT (TY4231) Figure 13 135"F/57"C Orange 1,2,3,4,5 N/A 155"F/68"C Red 175"F/79"C Yellow 200"F/93"C Green - 8.0 1/2" NPT PENDENT (TY4931) and UPRIGHT (1Y4831) 135"F/57"C Orange 1, 2,4, 5, 6 1, 2,5 155°F/68"C Red 175"F/79"C Yellow 200°F/93"C Green 286°F/141"C Blue NOTES: Listed by Underwriters Laboratories, Inc. (UL) as Quick Response Sprinklers. Listed by Underwriters Laboratories, Inc. for use in Canada (C-UL) as Quick Response Sprinklers. Approved by Factory Mutual Research Corporation (FM) as Quick Response Sprinklers. Approved by the Loss Prevention Certification Board (LPCB Ref. No. 007k104) as Quick Response Sprinklers; however, the LPCB does not rate the thermal sensitivity of recessed sprinklers. Approved by the City of New York under MEA 354-01-E. VdS Approved (For details contact Tyco Fire & Building Products, Enschede, Netherlands, Tel. 31-53-428-4444/Fax 31-53-428-3377). Approved by the Loss Prevention Certification Board (LPCB Ref. No. 094a/06) as Quick Response Sprinklers. Where Polyester Coated and Lead Coated Sprinklers are noted to be UL and C-UL Listed, the sprinklers are UL and C-UL Listed as Corrosion Resistant Sprinklers. Where Lead Coated Sprinklers are noted to be FM Approved, the sprinklers are FM Approved as a Corrosion Resistant Sprinklers. Installed with Style 10 (1/2" NPT) or Style 40 (3/4" NPT) 3/4" Total Adjustment Recessed Escutcheon, as applicable. ** Installed with Style 20 (1/2" NPT) or Style 30 (3/4" NPT) 1/2" Total Adjustment Recessed Escutcheon, as applicable. *** Frame and Deflector only. Listings and approvals apply to color (Special Order). N/A: Not Available TABLE B LABORATORY LISTINGS AND APPROVALS 5.6 AND 8.0 K-FACTOR SPRINKLERS S S S S TFPI7I Page 7 of 10 SPRINKLER FINISH K TYPE NATURAL CHROME WHITE LEAD BRASS PLATED I POLYESTER COATED PENDENT (TY3231) and 2.8 UPRIGHT (1V3131) 175 PSI (12,1 BAR) N/A 1/2 RECESSED PENDENT NPT (1Y323) PENDENT (1Y4231) and 4.2 UPRIGHT (TY4131) 175 PSI (12,1 BAR) N/A RECESSED PENDENT NPT (TY4231) PENDENT (TV3231) and 250 PSI (17,2 BAR) 175 PSI (12,1 BAR) 5.6 OR UPRIGHT (1Y3131) 1/2" 175 PSI (12,1 BAR) RECESSED PENDENT NPT (1Y3231) (SEE NOTE 1) N/A PENDENT (TY4231) and 175 PSI (12,1 BAR) 175 PSI (12,1 BAR) 8.0 UPRIGHT (TY4131) RECESSED PENDENT NPT (TY4231) N/A 8.0 PENDENT (TY4931) 1/2" and 175 PSI (12,1 BAR) 175 PSI (12,1 BAR) NPT UPRIGHT (1Y4831) NOTES: 1. The maximum working pressure of 250 psi (17,2 bar) only applies to the Listing by Underwriters Laboratories Inc. (UL); the Listing by Underwriters Laboratories,'lnc. for use in Canada (C-UL); and the Approval by the City of New York. TABLE C, MAXIMUM WORKING PRESSURE Installation The Series TY-FRB Sprinklers must be installed in accordance with the fol- lowing instructions: NOTES Do not install any bulb type sprinkler if the bulb is cracked or there is a loss of liquid from the bulb. With the sprinkler held horizontally, a small air bubble should be present. The diameter of the air bubble is approximately 1/16 inch (1,6 mm) for the 135 0F/57'C to 3/32 inch (2,4 mm) for the 2860F/141C temperature ratings. A leak tight 112 inch NPT sprinklerjoint should be obtained with a torque of 7 to 14 ft.lbs. (9,5 to 19,0 Nm). A maxi- mum of 21 ft. lbs. (28,5 Nm) of torque may be used to install sprinklers with 1/2 NPT connections. A leak tight 3/4 inch NPT sprinkler joint should be oh- tamed with a torque of 10 to 20 ft.lbs. (13,4 to 26,8 Nm). A maximum of 30 ft.lbs. (40,7 Nm) of torque is to be used to install sprinklers with 3/4 NPT con- nections. Higher levels of torque may distort the sprinkler inlet and cause leakage or impairment of the sprinkler. Do not attempt to make-up for insuffi- cient adjustment in the escutcheon plate by under- or over-tightening the sprinkler. Readjust the position of the sprinkler fitting to suit. The Series TY-FRB Pendent and Up- right Sprinklers must be installed in accordance with the following instruc- tions. Step 1. Pendant sprinklers are to be installed in the pendent position, and upright sprinklers are to be installed in the upright position. Step 2. With pipe thread sealant ap- plied to the pipe threads, hand tighten the sprinkler into the sprinkler fitting. Step 3. Tighten the sprinkler into the sprinkler fitting using only the W-Type 6 Sprinkler Wrench (Ref. Figure 14). With reference to Figures 1, 2, 3, 4, and 5, the W-Type 6 Sprinkler Wrench is to be applied to the sprinkler wrench flats. The Series TY-FRB Recessed Pen- dent Sprinklers must be installed in accordance with the following instruc- tions. Step A. After installing the Style 10. 20, 30, or 40 Mounting Plate, as appli- cable, over the sprinkler threads and with pipe thread sealant applied to the pipe threads, hand tighten the sprin- kler into the sprinkler fitting. Step B. Tighten the sprinkler into the sprinkler fitting using only the W-Type 7 Recessed Sprinkler Wrench (Ref. Figure 15). With reference to Figure 1, 2, 3, and 4, the W-Type 7 Recessed S TFPI 71 2-7/8" DIA. 5/8±1/4" (73,0 mm) 314" 19,1 mm I (15,916,4 mm) 2-1/4" DIA. I 1/4" (6.4 FACE OF (57,2 mm) MO TING SPRINKLER PLATE FITTING I 1/8" (3,2 mm) MOUNTING SURFACE SERIES 1-1/4" (31,8 mm) I CLOSURE T'fFRB 314"(19,1 mm) FIGURE 10 RIES TY-FRB RECESSED PENDENT WIT TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT STYLE 10 RECESSED ESCUTCHEON 5.6 K-FACTOR, 1/2 INCH NPT - 2-7/8" DIA. 5/6±1/4" (73,0 mm) 3/4" 19.1 mm) (15,9±6,4 mm) - 2-114" DIA, _.. 1/4" (6,4 m (57,2 mm) FACE OF MOU INC SPRINKLER TE FITTING / 118" I - (3.2mm) MOUNTING SURFACE CLOSURE SERIES 1-5/16" (33,3 mm) TYFRB 13/16"(20,6 mm) FIGURE 12 S IES TY-FRB RECESSED PENDENT WIT 0-PIECE 3/4 INCH TOTAL ADJUSTMENT STYLE 40 RECESSED ESCUTCHEON 8.0 K-FACTOR, 3/4 INCH NPT Page 9 of 10 2-7/8" DIA. (73,0 mm) 1/2±1/8" 1/2"(12,7 m (12,7±3,2 mm) - 2-1/4" DIA. . 1/4" (6,4 m) FACE OF (57.2 mm) MO TING SPRINKLER PLATE FITTING / 1/8" I (3,2 II mm) _ MOUNTING SURFACE CLOSURE SERIES 1.1/4(31,8 mm) TY.FRB 1"(25,4 mm) FIGURE 11 RIES TY-FRB RECESSED PENDENT WI TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 20 RECESSED ESCUTCHEON 5.6 K-FACTOR, 1/2 INCH NPT - 2-7/8" DIA. (73.0 mm) 1/2" 12,7 mm) (12,7±3.2 mm) - 2-1/4" DIA. i 1/4" (6,4 (57.2 mm) FACE OF MO TING SPRINKLER LATE FITTING I - (3,2 mm) MOUNTING SURFACE CLOSURE SERIES 1-5116"(33,3 mm) TY-FRB 1-1/16"(27.0 mm) FIGURE 13 RIES TY-FRB RECESSED PENDENT WIT TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 30 RECESSED ESCUTCHEON 8.0 K-FACTOR, 3/4 INCH NPT S pleted, to verify the integrity of the cor- rosion resistant coating. Thereafter, annual inspections per NFPA 25 should suffice; however, instead of in- specting from the floor level, a random sampling of close-up visual inspec- tions should be made, so as to better determine the exact sprinkler condi- tion and the long term integrity of the corrosion resistant coating, as it may be affected by the corrosive conditions present. The owner is responsible for the in- spection, testing, and maintenance of their fire protection system and de- vices in compliance with this docu- ment, as well as with the applicable standards of the National Fire Protec- tion Association (e.g., NFPA 25), in addition to the standards of any other authorities having jurisdiction. The in- stalling contractor or sprinkler manu- WRENCH RECESS (END "A" USED FOR 1/2" NPT MODELS) WRENCH RECESS (END "B" USED FOR 3/4" NPT MODELS) FIGURE 14 W-TYPE 6 SPRINKLER WRENCH facturer should be contacted relative to any questions. It is recommended that automatic sprinkler systems be inspected, tested, and maintained by a qualified WRENCH RECESS PUSH WRENCH IN TO ENSURE ENGAGEMENT WITH SPRINKLER WRENCHING AREA FIGURE 15 W-TYPE 7 RECESSED SPRINKLER WRENCH Inspection Service in accordance with local requirements and/or national codes. 0 Page 10 of 10 TFPI7I P/N 57-XXX-X-XXX I L MODEL/SIN 330 2.8K UPRIGHT (1/2"NPT) TYI13I 331 2.8K PENDENT (1/2"NPT) 7Y1231 340 4.2K UPRIGHT (1/2"NPT) TY2131 341 4.2K PENDENT (1/2"NPT) TY2231 5.6K UPRIGHT (1/2"NPT) TY3131 E370 371 5.6K PENDENT (1/2NPT) TY3231 390 8.0K UPRIGHT (314"NPT) TY4131 391 8.0K PENDENT (3/4"NPT) TY4231 360 8.0K UPRIGHT (1/2"NPT) TY4831* 361 8.0K PENDENT (1/2"NPT) TY4931 I I I 135 155 175 200 286 RATING SPRINKLER 135*F/57*C 1 NATURAL BRASS 155*F/68*C 4 WHITE POLYESTER 175*F/79*C 3 WHITE (RAL90I0)* 200°F/93C 9 CHROME PLATED 286*F1141*C 7 LEAD COATED * Eastern Hemisphere sales only. TABLED PART NUMBER SELECTION SERIES TY-FRB PENDENT AND UPRIGHT SPRINKLERS Limited Warranty Products manufactured by Tyco Fire & Building Products (TFBP) are war- ranted solely to the original Buyer for ten (10) years against defects in mate- rial and workmanship when paid for and properly installed and maintained under normal use and service. This warranty will expire ten (10) years from date of shipment by TFBP. No warranty is given for products or com- ponents manufactured by companies not affiliated by ownership with TFBP or for products and components which have been subject to misuse, improper installation, corrosion, or which have not been installed, maintained, modi- fied or repaired in accordance with ap- plicable Standards of the National Fire Protection Association, and/or the standards of any other Authorities Having Jurisdiction. Materials found by TFBP to be defective shall be either repaired or replaced, at TFBP's sole option. TFBP neither assumes, nor authorizes any person to assume for it, any other obligation in connection with the sale of products or parts of prod- ucts. TFBP shall not be responsible for sprinkler system design errors or inac- curate or incomplete information sup- plied by Buyer or Buyer's repre- sentatives. In no event shall TFBP be liable, in contract, tort, strict liability or under any other legal theory, for incidental, indirect, special or consequential dam- ages, including but not limited to labor charges, regardless of whether TFBP was informed about the possibility of such damages, and in no event shall TFBP's liability exceed an amount equal to the sales price. This limited warranty sets forth the ex- clusive remedy for claims based on failure of or defect in products, materi- als or components, whether the claim is made in contract, tort, strict liability or any other legal theory. This warranty will apply to the full ex- tent permitted by law. The invalidity, in whole or part, of any portion of this warranty will not affect the remainder. Ordering Procedure When placing an order, indicate the full product name. Refer to the Price List for complete listing of Part Num- bers. Contact your local distributor for avail- ability. Sprinkler Assemblies with NPT Thread Connections: Specify: (Specify Model/SIN), Quick Response, (specify K-factor), (specify temperature rating), Series TY-FRB (specify Pendent or Upright) Sprinkler with (specify type of finish or coating), P/N (specify from Table D). Recessed Escutcheon: Specify: Style (10, 20, 30, or 40) Re- cessed Escutcheon with (specify*) fin- ish, P/N (specify*). * Refer to Technical Data Sheet TFP770. Sprinkler Wrench: Specify: W-Type 6 Sprinkler Wrench, P/N 56-000-6-387. Specify: W-Type 7 Sprinkler Wrench, P/N 56-850-4-001. TYCO FIRE & BUILDING PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446 Bulletin 034 Rev. D bILA Model G5-80, Model G5-56, Model G5-42, Model G5-28 Quick Response Concealed Automatic Sprinkler CD 0 CD a UL Quick Response FM Standard Response Concealed Sprinkler With a 3/499 (19mm) Adjustment Features Cover plate attachment (Plain or Perforated) with 3/4" (19mm) assembly adjustment. Smooth aesthetic ceiling profile. Factory installed protective cap. Available in Chrome and White as Standard Finish- es. Special Application Finishes are also available. Ordinary and Intermediate temperature rating. For additional Sprinklers refer to Bulletin 154 for Technical Specification and Approvals Approvals & Listings 1. Underwriters Laboratories Inc. and cULus - Quick Response G5-80, G5-56 - Light Hazard and Ordinary Hazard Occupancies G5-42 - Light Hazard Occupancies G5-28 - Light Hazard Occupancies 2. Factory Mutual Research Corp. (FM) - Standard Response (See Page 3) G5-56 & G5-28 only. See the most recent FM Global Property Loss Prevention Data Sheets for installation and use guidelines. 3. Loss Prevention Council (LPCB, UK) - Standard Response G5-56 - Light Hazard and Ordinary Hazard Occupancies vdS SchadenverhUtung GmbH - Standard Response EC-Certificate of Conformity 0832-CPD-2062 U.S. Patent number 6,554,077. Application The Reliable Model G5-80, G5-56, G5-42 and G5-28 are the most versatile quick response concealed sprinklers avail- able. It provides the best form of fire protection while offering an attractive appearance and 3/4" (19mm) of cover adjust- ment for ease of installation. The small diameter cover plate assembly is easily attached and blends into the ceiling, con- cealing the most dependable fire protection available, an au- tomatic sprinkler system. Plain Cover Plate Perforated Cover Plate The Model G5-80, G5-56, G5-42 and G5-28 are designed for use where aesthetic appearance is important. Offices, hos- pitals, motels and restaurants are but a few of the applications where it can be used. The Model G5-80, G5-56, G5-42 and G5-28 are UL Listed Quick Response Concealed sprinklers intended for use in accordance with NFPA 13. FM Approves the G5-56 and the G5-28 sprinkler as a standard response concealed sprinkler intended for use in accordance with FM Loss Prevention Data Sheet 2.0. Product Description The Reliable Model G5-80, G5-56, G5-42 and G5-28 uses a proven quick response fusible element in a standard style sprinkler frame with a drop-down deflector. This assembly is recessed into the ceiling and concealed by a flat cover plate assembly. The threaded engagement provides 3/4" (19mm) of cover adjustment. The flat cover plate is attached to the skirt using either 135°F (57°C) or 165°F (74°C) ordinary tempera- ture classification solder. When the ceiling temperature rises, the solder holding the flat cover plate melts, the flat cover plate released thus expos- ing the sprinkler inside to the rising ambient temperature. The subsequent fusing of the element opens the waterway and causes the deflector to distribute the water. Any secure engagement between the cover plate and cup will assure that the drop-down deflector is properly located below the ceiling. Reliable Automatic Sprinkler Co., Inc., 103 Fairview Park Drive, Elmsford, New York 10523 Model FC Sprinkler Wrench UL Listing Category Sprinklers, Automatic and Open Quick Response Sprinkler UL Guide Number VN IV Installation Do not install the G5-80, G5-56, G5-42 and G5-28 in ceilings which have positive pressure in the space above. Cut a 2" inch (67mm) diameter hole is cut in the ceiling, the sprinkler is easily installed with the Model FC Wrench. The wrench has a socket drive which is inserted into the body of the sprinkler. When installing a sprinkler the wrench is first positioned into the sprinkler/cup assembly until the wrench socket engages the body of the sprinkler. The sprinkler is then tightened into the pipe fitting. When inserting or remov- ing the wrench from the sprinkler/cup assembly, care should be taken to prevent damage to the sprinkler. DO NOT WRENCH ON ANY OTHER PART OF THE SPRINKLER! CUP ASSEMBLY. Install the cover plate by hand turning the cover in the clockwise direction until it is tight against the ceil- ing. A protective cap is provided to protect the drop-down sprinkler deflector from damage which could occur during construction before the cover plate is installed. The cap is factory installed inside the sprinkler cup. Remove cap to install sprinkler, then re- install cap until the cover plate is installed. Maintenance The Model G5-80, G5-56, G5-42 and G5-28 should be in- spected and the sprinkler system maintained in accordance with NFPA 25. Do not clean sprinklers with soap and water, am- monia or any other cleaning fluids. Remove any sprinkler that has been painted (other than factory applied) or damaged in any way. Concealed sprinklers cover plates can not be painted in the field, after installation or have any other coating applied other than the factory finish. A stock of spare sprinklers should be maintained to allow quick replacement of damaged or oper- ated sprinklers. Prior to installation, sprinklers should be main- tained in the original cartons and packaging to minimize the potential for damage to sprinklers that would cause improper operation or non-operation. Ordering Information Sprinkler Model Nominal Orifice Flat Cover Plate Plain or Perforated Flat Cover Plate Assembly Finish Inlet Type Cover Plate Finishes' Standard Finishes Chrome White Paint Special Application Finishes(2) Bright Brass Finished Bronze Black Plating Black Paint Off White Satin Chrome Other finishes and colors are available on special order. Consult factory for details. Coverplate custom paint is semi-gloss, unless specified otherwise. For the perforated style cover- plate, consult factory for avail- ability on these and other cus- tom finishes. Maximum Working Pressure 175 psi (12 bar) 100% Factory tested Hydrostatically to 500 psi (34.5 bar) Temperature Rating Classification Sprinkler Cover Max. Ambient Plate Temp. Ordinary 1 65°F/74°C 135°F/57°C 100°F/38°C Intermediate 212°F/1 00°C 1650F/740C 150°F/660C 2. S S Technical Data Sprinkler Model Sprinkler Inlet Total Adjustment Nominal Orifice Nominal K Factor Thread Metric Arovals pp Sprinkler Identification (SIN) US G5-80 Non Adjustable 3%"(19mm) 17/32"(l5mm) 8,0 115 34" NPT(R3A) 1 RA3412 G5-56 Non Adjustable 3%"(19mm) 1/2"(15mm) 5.6 80 1/2" NFl (R1/2) 1,2,34,5 RA3415 G5-42 Non Adjustable 3%" (19mm) /16" (10mm) 1 4.2 60 ½" NFl (R½) 1 RA3413 G5-28 Non Adjustable 3%"(19mm) 3h"(10mm) 1 2.8 40 ½" NPT(R1/2) 1,2 RA3411 For VdS Approval, temperature rating sprinkler 1650F174°c and cover plate 135°F1570C only! 1 x 1/2" REDUCING TEE OR ELBOW I 1 . 3/4" REDUCING TEE OR ELBOW - ONLY - - - - - I ..CB L oo.ommJ " [58.42mm] DIA HOLE IN CEILING CUP -._.. " [19.05mm] MAX COVER ADJUSTMENT 1/4[6.35mm] ANN TO CEILING 1 [25 4mm] MAX DROPPED DEFLECTOR TO CEILING 2-1/4" [57.15mm] MAX. FACE OF FIT7NG TO FACE OF CEILING DIMENSION FLAT COVER PLATE ASSEMBLY [84.2 1mm] DL4. J- [4.96mm] SPRINKLER COVER PLATE: 3/4" [19.05mm] ADJUSTMENT Notice FOR USE AS A REPLACEMENT OF MODEL G4A SPRINKLERS 1" x 7/2" REDUCING TEE OR ELBOW L__. ----4—.-- t --III -Iii---- _r REUABLE P/N 6999991900 " X " BRASS NIPPLE EX '--,-T. 4" [58.42mm] DL4 - CUP (19.05mm] MAX. COVER ADJUSTMENT / 1/4" (6.35mm1 U/N, TO CEILING 1" (25.4mm] MAX. DROPPED DEFLECTOR TO CEILING J~ FLAT COVER PLATE ASSEMBLY SPRINKLER 4" (84.2 7mm] DLA. .2" (66.55mm] 1 HOLE IN CEILING 3-1/16" [77.72mm] MAX. FACE OF FIT11NG TO FACE OF CEILING DIMENSION 2-7/4" [57.75mm] MAX. FACE OF NIPPLE EXI TO FACE OF CEILING DIMENSION /" [4.96mm] COVER PLATE: 3/4" [19.05mm] ADJUSTMENT Testing has shown that use of a "nipple extension" will not affect the listing of the sprinkler. For RETROFIT installations, per NFPA 13 (2010) section 815.19.4, "which allows the use of nipples as the same pipe thread size as the existing outlet when revamping existing systems". Do not exceed 8-18 ft-lbs of torque during installation. - 3. Reliable ... For Complete Protection •Reliable offers a wide selection of sprinkler components. Following are some of the many precision-made Reliable products that guard life and property from fire around the clock. Automatic sprinklers Flush automatic sprinklers Recessed automatic sprinklers Concealed automatic sprinklers Adjustable automatic sprinklers Dry automatic sprinklers Intermediate level sprinklers Open sprinklers . Spray nozzles Alarm valves Retarding chambers Dry pipe valves Accelerators for dry pipe valves Mechanical sprinkler alarms Deluge valves Detector check valves Check valves Electrical system Sprinkler emergency cabinets Sprinkler wrenches Sprinkler escutcheons and guards Inspectors test connections 'Sight drains Ball drips and drum drips Control valve seals Air maintenance devices Air compressors Pressure gauges Electrical sprinkler alarm switches Identification signs Water flow detectors ' Fire department connection The equipment presented in this bulletin is to be installed in accordance with the latest published Standards of the National Fire Protection Association, Factory Mutual Research Corporation, or other similar organizations and also with the provisions of governmental codes or ordinances whenever applicable. Products manufactured and distributed by Reliable have been protecting life and property for over 90 years, and are installed and serviced by the most highly qualified and reputable sprinkler contractors located throughout the United States, Canada and foreign countries. Manufactured by Rellableo Reliable Automatic Sprinkler Co., Inc. (800) 431-1588 Sales Offices (800) 848-6051 Sales Fax (914) 829-2042 Corporate Offices www.reliablesprinkler.com Internet Address @ Recycled Paper Revision lines indicate updated or new data. EG. Printed in U.S.A. 11/14 P/N 9999970421 S RING HANGER S <jR> C®US I thru 4 Inch pipe 112 and 314 inch pipe 5 thru 8 inch pipe SIZE - 1/2 thru 8 inch pipe. MATERIAL - Carbon Steel, Mu. Galvanized to G-90 specification. FINISH - Mu. Galvanized and Stainless Steel. LISTING - UL in US and CANADA. APPROVAL - Factory Mutual Research. CONFORMS WITH: Federal Specification WW-H- 17 1 (Type 10), Manufacturers Standardization Society ANSI!MSS-SP-58 (Type 10); install in accordance with ANSI/MSS- SP-69. MAXIMUM TEMPERATURE - 650°F. FUNCTION - For fire sprinkler and general piping purposes. Swivel nut permits hanger adjustment after installation. FEATURES - 1 thru4 inch: * Offset edge for EASY pipe insertion. l thru. 8 inch: * Full length knurl on swivel nut for better grip. UNIQUE FEATURES 1 thru 3 inch: * UL listed to accept AFCON#3 10 Surge Restrainer. * Swivel nut Retained in ring to keep the assembly intact prior to installation. Removed easily if needed. * UL listed for use on CPVC pipe. ORDERING - Part # and pipe size. Index 02/01 IMPERIAL MAX REC. LOAD LBS. METRIC* PIPE ROD PIPE ROD 400 10 3/4 3/8 400 20 10 400 s 10 3/8 400 32 to 1 112 3/8 400 40 to 3/8 400 50 10 21/2 3/8 600 65 10 3/8 600 80 10 31/2 600 1 to 4 3/8 1000 100 to 5 1250 125 12 6 1250 150 12 8 112 1 1250 1 200 12 * Order Part #300m Note: 1/2" Ring Hanger not <FM> approved 655 ALL THREADED ROD CUT TO LENGTH ROD SIZE MAX. REC. FOR SERVICE LOAD LBS. TEMP. 650°F 750°F 3/8 610 540 1/2 1130 1010 5/8 1810 1610 3/4 2710 2420 7/8 3770 3360 NOTE; maximum Temperature: 750°F SIZE - 3/8 thru 7/8 inch rod in linch increments. MATERIAL - Carbon Steel. FINISH - Plain, Electro-Galvanized and Stainless Steel. ORDERING - Part #, rod diameter, rod length and finish. 2/00 8 i #14 (Item #100-black) Sammys 1/4", 3/8" red WOOD - Sammys T (VerticalI 'Use #14 Nut Driver (Item #100) Item# Model ShkLgth ShkDia BoxQty Weight Case (per 100) Qty 20 CST.750 3/4 1/4 100 4.75 1000 21 GST 100 1 1/4 100 5.00 1000 22 GST 200 2 1/4 100 6.50 23 G5T300 3 1/4 100 7.50 tOO 24 GST 600 6 1/4 50 9.00 WOOD - 3/8"IRod (VerticalI iTTflTh Use #14 Nut Driver (Item #100) Item # Approvals Model Shk Lgth Shk Dia UIiFMls Load, lb ULlest Load lb Pipe Size Actual Pullout Box Qty 10 CST.75 3/4 1/4 564#-6Ply 100 NFPA 11 CST 10 1 1/4 2104 - 7/16 OSB100 6704 - 3/4" Ply IUL-FM-NFPA 12 GST 20 2 1/4 940# 8504 3/4-2 1/2 17604 -Fir 100 UL-NFPA * 27 GST 25-380 21/2 3/8 15004 4 21134-Fir 50 UL-FM-NFPA 13 GST30 3 1/4 1475# 15004 3/4-4 20604-Fir 100 NFPA 403 CST40 1 4 1/4 21804-Fir 50 NFPA 14 IGST60 1 6 1 1/4 22304-Fir 50 #I4SW (Item #101-rec Sidewinders & Sammys 1/2" rod Rodristttii u Use #14SW Nut Driver (Item #101) rnrnm Item # Model Shk Lgth Shk Dia Actual Pullout Box Qty Weight Case Qty 8 CST 2 2 1/4 17604- Fir 50 7.00 500 * 06 GST2.5-380 21/2 3/8 21134-Fir 50 10.00 500 15 IGST3 3 1/4 22754-Fir 50 1 10.50 500 16 JGST4 4 1/4 21804-Fir 50 10.60 500 17 IGST6 6 1 1/4 1 22304-Fir 50 10.95 500 Not less than 1" nominal width (11/2") .00 NE NE z c 00 d Joist L mum 2" Imbedment Into base rial for NFPA 13 compliance TJI Joist !Truss Consult truss manufacturer for recommended Installation point. *pre.dr111ing may be required for items #27 and #06. Tools available on page 9. Forverticalluse. Installation-' Install In center oftewerface. :: L- per NFPA 1 Page 4 Note: Screws must be installed with appropriate nut driver to comply with warranty WOOD —Sidewinders It #I4SW (item #101-red) Sidewinders& Sammysll2"rod WOOD VE11RodIU flT VAIl I1fl Mount) Use #14SW Nut Driver (Item #101) I Model Item # ShkLgth l ShkDia I Actual IShear/Pu1lout I Box Qty I Weight ICase Qty (per 100) 4016 ISWG100 1 1/4 I 100 7.50 I 1000 300 ISWG200 2 1/4 1725# - Fir 100 8.00 1000 AiISl (HorizontalMount) Use #14SWNutDrnr (Item#101) Approvals Item# Model Shk Lgth Shk Dia UL Test Load lb. UI/FM Pipe Size ActualBox Shear/Pullout Qty Weight ( (per 100) 18 SWG10 1 1/4 100 6.00 UL•NFPA 19 SWG20 2 1/4 1250# 3 1725# - Fir 100 7.00 UL-NFPA * 26 SWG25-380 2 1/2 3/8 1500# 1 4 1 2249# - Fir 50 10.25 - 25 SWG30 3 1/4 1 1 50 8.50 Floor Joist r Not less than 2" nominal width (1112") up to 3112" pipe; not less than 3" nominal width 4" & 5" pipe S TJI Joist! Truss Consult truss manufacturer for recommended installation point. *pre..drilling may be required for item #26. Tools available on page 9. I SHEETROCK Minimum 2 112" from bottom for branch lines. Minimum 3" from bottom for mainlines. Exception: This requirement shall not apply to 2" or thicker nailing strips resting on top of steel beams. - Toggle S ii :i D I t(SIS1 1EII1 1T (Vertical T1I flTiiTh Use #14 Nut Driver (Item #100) Item# I Model Shk Lgth Shk Dia Actual Pullout Box Qty I Weight Case Qty (per 100) 71 SST 300 3 1/4 450# Lath & Plaster I 50 12.00 I 500 404# 2 Layers 5/8 Rock ii :i Di DI I lull ria: im rI!n7tti1L' mimi 'Use #14 Nut Driver (Item #100) Item# Model Shk Lgth Shk Dia I Actual Pullout Pkg Qty I Weight Case Qty (per 100) I 70 ISST 30 1/4 450# Lath & Plaster I I 12.00 I 500 404# 2 Layers 5/8 Rock Note: Screws must be installed with appropriate nut driver to comply with warranty iL) #14 (Item #100-black) Sammys 114", 318" red T.' Prestressed Concrete CDO. C7 Page 5