Loading...
HomeMy WebLinkAbout1896 RUTHERFORD RD; ; FPC2021-0101; PermitPERMIT REPORT 4LrP of Carlsbad Print Date: 11/03/2021 Job Address: 1896 RUTHERFORD RD, CARLSBAD, CA 92008-7326 Permit Type: FIRE-Construction Commercial Work Class: Fire Sprinklers Parcel #: 2121203000 Track U: Valuation: $374,777.58 Lot #: Occupancy Group: Project U: #of Dwelling Units: Plan U: Bedrooms: Construction Type: Bathrooms: Orig. Plan Check U: Plan Check U: Project Title: Description: ARGONAUT - SPRINKLER TI (31 HEADS) Permit No: FPC2021-0101 Status: Closed - Finaled Applied: 06/08/2021 Issued: 06/16/2021 Finaled Close Out: 11/03/2021 Inspector: Final Inspection: Applicant: FPContractor: AMERICAN AUTOMATIC FIRE SUPPRESSION AMERICAN AUTOMATIC FIRE SUPPRESSION INC INC KELLY SANTOS 9925 PROSPECT AVE, U STE B 9925 PROSPECT AVE, # STE B SANTEE, CA 92071 SANTEE, CA 92071-4376-SAN DIEGO (619) 562-3010 (619) 562-3010 FEE AMOUNT FIRE NFPA 13 or 13R System 7 - 100 heads $553.00 FIRE Reinspection (per Inspection) $212.00 Total Fees: $765.00 Total Payments To Date: $765.00 Balance Due: $0.00 Fire Department Page 1 of 1 1635 Faraday Avenue, Carlsbad CA 92008-7314 760-602-4665 1 760-602-8561 f I www.carlsbadca.gov Worldwide tqcce Contacts www.tyco-fire.com Model ESFR-17 168 K-factor Pendent Sprinkler Early Suppression, Fast Response General Description TYCO Model ESFR-17 Pendent Sprin- klers are Early Suppression, Fast Response (ESFR) sprinklers having a nominal K-factor of 16.8 (See Figure 1). They are suppression mode sprinklers that are especially advantageous as a means of eliminating in-rack sprinklers when protecting high-piled storage. The Model ESFR-17 Pendent Sprinklers are available in two temperature ratings and Listed or Approved accordingly; 155°F (68°C) is UL and C-UL Listed and IM Approval; and 200°F (93°C) is UL and C-UL Listing only. Model ESFR-17 Pendent Sprinklers are primarily used for ceiling-only sprinkler protection of (but not limited to) the fol- lowing storage applications: most encapsulated or non-encap- sulated common materials including cartoned, unexpanded plastics cartoned, expanded plastics uncartoned, unexpanded plastics uncartoned, expanded plastics some storage arrangements of rubber tires, roll paper, and aerosols For more specific criteria, refer to Table A in this technical data sheet as well as the applicable design standard. The Model ESFR-17 Pendent Sprin- klers provide the system designer with hydraulic and sprinkler place- IMPORTANT Refer to Technical Data Sheet TFP2300 for warnings pertaining to regulatory and health information. Always refer to Technical Data Sheet TFP700 for the "INSTALLER WARNING" that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and installation can permanently damage a sprinkler system or its compo- nents and cause the sprinkler to fail to operate in a fire situation or cause it to operate prematurely. Page 1 of 4 ment options not presently available to traditional ESFR Sprinklers having a nominal K-factor of 14.0. In particu- lar, Model ESFR-17 Pendent Sprinklers are designed to operate at substan- tially lower-end head pressures, as compared to ESFR Sprinklers having a nominal K-factor of 14.0. This feature offers flexibility when sizing system piping, as well as possibly reducing or eliminating the need for a system fire pump. Applications for the ESFR-17 Pendent Sprinklers are expanding beyond cur- rently recognized installation stan- dards. For information on research fire tests (with flammable liquids and aero- sols, for example) that may be accept- able to an authority having jurisdiction, contact Technical Services. IWAYthIIL(CI Orange protector must NOT be removed until sprinkler is to be placed in service. The W-Type 35 Sprinkler Wrench MUST be used for proper installation of the sprinkler. Failure to do so may result in equipment damage or failure. LT1cE The Model ESFR-17 Pendent Sprinklers described herein must be installed and maintained in compliance with this document, as well as with the appli- cable standards of the National Fire Protection Association (NFPA), in addi- tion to the standards of any authorities having jurisdiction, such as FM Global. Failure to do so may impair the perfor- mance of these devices. The owner is responsible for main- taining their fire protection system and devices in proper operating con- dition. Contact the installing contrac- tor or product manufacturer with any questions. In all cases, the appropriate NFPA or FM Global installation standard, or other applicable standard, must be ref- erenced to ensure applicability and to obtain complete installation guidelines. The general guidelines in this technical data sheet are not intended to provide complete installation criteria. APRIL 2019 Sprinkler Identification Number (SIN) TY7236 Technical Data Approvals UL and C-UL Listed FM Approved * 155'F (68'C) temperature rating only. Maximum Working Pressure 175 psi (12,1 bar) Pipe Thread Connections 34 in. NPT or ISO 7-fl 3/4 Discharge Coefficient K=16.8 gpm/psit'z (241,9 1pm/bar) Temperature Ratings 155°F (68°C)1 200°F (930C)2 tJL/C-UL Listed and EM Approved. UL/C-UL Listed only. Finish Natural Brass Physical Characteristics Frame .............................Brass Deflector ..........................Bronze Compression Screw ..................Brass Button ...................Phosphor Bronze Bulb(3mm) .........................Glass Sealing Assembly.. Beryllium Nickel w/TEFLON TFP322 1FP322 Page 2 of 4 Components: 3/4' NPT' 1 - Frame 3 - Compression Screw 4 - Bulb 1-1/2 5Bufton I FLATS 1/2' ffm 6 - Sealing Assembly (LT) 2-3/8" 2 - Deflector* 5 WRENCH (38,1 mm) NOMINAL (12,7 mm) (60,3 mm) * Temperature rating is indicated on Deflector. MAKE-IN CENTERLINE ISO 7-R 3/4 pipe thread THERMAL can be provided on SENSING ** special request. 2 ELEMENT FIGURE 1 MODEL ESFR-17 EARLY SUPPRESSION, FAST RESPONSE 16.8K PENDENT SPRINKLER ASSEMBLY AND DIMENSIONS Design Criteria The following general guidelines pro- vided for the TYCO Model ESFR-17 Pendent Sprinklers can be used for a quick reference. The National Fire Protection Associa- tion (NFPA) or FM Global provide instal- lation standards that must be used to properly design an automatic sprinkler system utilizing Early Suppression, Fast Response (ESFR) Sprinklers. Conse- quently, the appropriate standard must be used for a given installation. In all cases, the appropriate NFPA or FM Global installation standard must be referenced to ensure applicabil- ity and to obtain complete installa- tion guidelines. The following general guidelines are not intended to provide complete installation criteria. System Type Wet Pipe Roof Construction Unobstructed or obstructed construc- tion, such as smooth ceiling, bar joists, beam and girder. Where the depths of the solid structural members, such as beams and stem, exceed 12 in. (302 mm), install ESFR Sprinklers in each channel formed by the structural members. Ceiling Slope Maximum 2 in. rise for 12 in. run (16.7%) Maximum Coverage Area 100 ft2 (9,3 m2) In some cases, the installation stan- dards permit a greater coverage area. Minimum Coverage Area 64 ft2 (5,8 m2) per NFPA 13 and FM Global 2-0 Maximum Spacing 12 ft (3,7 m) for building heights up to 30 ft (9,1 m) 10 ft (3,1 m) for building heights greater than 30 ft (9,1 m) Minimum Spacing 8ft(2,4m) Minimum Clearance to Commodity 36 in. (914 mm) NFPA 13 Deflector-to-Ceiling Distance 6 to 14 in. (152 to 356 mm) Centerline of Thermal Sensing Element to Ceiling Distance Refer to FM Global 2-0 for Storage Sprinklers Operation The glass bulb contains a fluid which expands when exposed to heat. When the rated temperature is reached, the fluid expands sufficiently to shatter the glass bulb, allowing the sprinkler to activate and water to flow. TFP322 Page 3 of 4 Storage Type NFPA FM Global Open Frame (i.e., no solid shelves) Refer to NFPA 13 Single, Double, Multiple-Row, or Portable Rack Storage of Chapters 16 and 17 Refer to FM 2-0 and 8-9 Class l-IV and Group A or B Plastics Solid Pile or Palletized Storage of Class l-IV and Group A or B Plastics Refer to NFPA 13 Chapters 14 and 15 Refer to FM 2-0 and 8-9 Idle Pallet Storage Refer to NFPA 13 Chapter 12 Refer to FM 2-0, 8-9, and 8-24 Rubber Tire Storage Refer to NFPA 13 Chapter 18 Refer to FM 2-0 and 8-3 Roll Paper Storage (Refer to the Standard) Refer to NFPA 13 Chapter 19 Refer to FM 8-21 Flammable/Ignitable Liquid Storage (Refer to the Standard) Refer to NFPA 30 Refer to FM 7-29 Aerosol Storage (Refer to the Standard) Refer to NFPA 30B Refer to FM 7-31 Automotive Components in Portable Racks N/A N/A (Control mode only; refer to the Standard) N/A - Not Applicable TABLE A MODEL ESFR-17 PENDENT SPRINKLER COMMODITY SELECTION AND DESIGN CRITERIA OVERVIEW Installation TYCO Model ESFR-17 Early Suppres- sion, Fast Response 16.8K Pendent Sprinklers must be installed in accor- dance with this section. General Instructions Do not install any bulb type sprinklers if the bulb is cracked or there is a loss of liquid from the bulb. With the sprin- kler held horizontally, a small air bubble should be present. The diameter of the air bubble is approximately 1/16 inch (1,6 mm) for both 155°F (68°C) and 200°F (93°C) temperature ratings. A leak-tight 3/4 inch NPT sprinkler joint should be obtained by applying a min- imum-to-maximum torque of 10 to 20 ft.-Ibs. (13,4 to 26,8 Nm), or by hand- tightening and applying an additional 1-1/4 to 1-1/2 revolutions of the wrench. Higher levels of torque can distort the sprinkler inlet with consequent leakage or impairment of the sprinkler. I!FAY:I'II'(eI Orange protector must NOT be removed until sprinkler is to be placed in service. The W-Type 35 sprinkler wrench MUST be used for proper installation of the sprinkler. Failure to do so may result in equipment damage or failure. Note: Install the Model ESFR-17 Pendent Sprinkler only in the pendent position (See Figure 2). Step 1. With pipe-thread sealant applied, hand-tighten the sprinkler into the sprinkler fitting. Do not apply pres- sure to the bulb assembly, and handle the Model ESFR-17 Sprinkler only by the Frame arms. Step 2. Wrench-tighten the Model ESFR-17 Sprinkler using only the W-Type 35 Sprinkler Wrench (See Figure 2), and by fully engaging (seating) the wrench on the sprinkler wrench flats (See Figure 1). Step 3. After installation, inspect the bulb of each Model ESFR-17 Sprinkler for damage. In particular, verify that the bulb is not cracked. Replace damaged sprinklers. FITTING SIDE TOWARD SPRINKLER FITTING & ~11 W 4CHN REN RECESS \~ FIGURE 2 W-TYPE 35 SPRINKLER WRENCH TFP322 Page 4 of 4 Care and Maintenance TYCO Model ESFR-17 Early Suppres- sion, Fast Response 16.8K Pendent Sprinklers must be maintained and ser- viced in accordance with this section. Before closing a fire protection system main control valve for maintenance work on the fire protection system that it controls, obtain permission to shut down the affected fire protection system from the proper authorities and notify all personnel who may be affected by this action. Sprinklers which are found to be leaking or exhibiting visible signs of corrosion must be replaced. Automatic sprinklers must never be painted, plated, coated, or other- wise altered after leaving the factory. Modified sprinklers must be replaced. Sprinklers that have been exposed to corrosive products of combustion, but have not operated, should be replaced if they cannot be completely cleaned by wiping the sprinkler with a cloth or by brushing it with a soft bristle brush. Care must be exercised to avoid damage to the sprinklers before, during, and after installation. Sprin- klers damaged by dropping, striking, wrench twist/slippage, or the like, must be replaced. Also, replace any sprin- kler that has a cracked bulb or that has lost liquid from its bulb (See Installa- tion section). The owner is responsible for the inspection, testing, and maintenance of their fire protection system and devices in compliance with this document, as well as with the applicable standards of the National Fire Protection Asso- ciation (e.g., NFPA 25), in addition to the standards of any authorities having jurisdiction. Contact the installing con- tractor or product manufacturer with any questions. Automatic sprinkler systems are rec- ommended to be inspected, tested, and maintained by a qualified Inspec- tion Service in accordance with local requirements and/or national codes. Limited Warranty For warranty terms and conditions, visit www.tyco-fire.com. Ordering Procedure Contact your local distributor for avail- ability. When placing an order, indicate the full product name and part number (P/N). Sprinkler Assemblies with 3/4 NPT Thread Connection Specify: Model ESFR-17 Early Sup- pression, Fast Response 16.8K Pendent Sprinklers (TY7236) with 3/4 NPT thread connection, (specify tem- perature rating), with Natural Brass finish, P/N (specify): 155°F (66°C)1 .................58-462-1-155 200°F (93°c)2 ................. 58-462-1-200 I. LJLIC-UL Listed and FM Approved. 2. tJL/C-IJL Listed only. Special Order Sprinkler Assemblies with ISO 7-14 3/4 Thread Connection Specify: Model ESFR-17 Early Suppres- sion, Fast Response 16.8K Pendent Sprinklers (TY7236) with ISO 7-R 3/4 thread connection, (specify tempera- ture rating), with Natural Brass finish, P/N (specify): 155°F (68°C)1 ................. 58-463-1 -155 200°F (93°C)2 ................. 58-463-1 -200 UL/C-UL Listed and FM Approved. ULIC-UL Listed only. Sprinkler Wrench Specify: W-Type 35 Sprinkler Wrench P/N 56-463-1-001 1400 Pennbrook Parkway, Lansdale, PA 194461 Telephone +1-215-362-0700 0 2019 Johnson Contrin. All flght, nane,nad. All ,ponlflcationn and ether info,',natinn eheren were current an of d000n,oet revinlon dot, and om orobjaetto change without notice. NATIONAL FIRE PROTECTION ASSOCIATION 0d NFPAan,ngl,tor,d tredemado of 0050001 Fire P,ofnttloflA0000lotiooi TEFLON Is rngletnrnd trod0nedr of DuPont J Al't,ohnson Controls t Fire Protection Products Worldwide Contacts www.tyco4ire.com Series DS-1 - 56 K-factor, Dry-type Sprinklers Pendent, Upright, and Horizontal Sidewall Standard Response, Standard Coverage General Description TYCO Series DS-1 5.6K Pendent, Upright, and Horizontal Sidewall, Stan- dard Response (5 mm bulb), Standard Coverage Dry-type Sprinklers are dec- orative glass bulb automatic sprinklers typically used where: pendent sprinklers are required on dry pipe systems that are exposed to freezing temperatures (e.g., sprin- kler drops from unheated portions of buildings) sprinklers and/or a portion of the connecting piping may be exposed to freezing temperatures (e.g., sprin- kler drops from wet systems into freezers, sprinkler sprigs from wet systems into unheated attics, or hor- izontal piping extensions through a wall to protect unheated areas of a building such as loading docks, over- hangs, and building exteriors) sprinklers are used on systems that are seasonably drained to avoid freezing (e.g., vacation resort areas) FILTOMM Series DS-1 Dry-type Sprinklers described herein must be installed and maintained in compliance with this document, as well as with the applica- ble standards of the National Fire Pro- tection Association (NFPA), in addition to the standards of any other authori- ties having jurisdiction. Failure to do so may impair the performance of these devices. IMPORTANT Always refer to Technical Data Sheet TFP700 for the "INSTALLER WARNING" that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and installation can permanently damage a sprinkler system or its compo- nents and cause the sprinkler to fall to operate in a fire situation or cause it to operate prematurely. Page 1 of 10 The owner is responsible for main- taining their fire protection system and devices in proper operating con- dition. Contact the installing contrac- tor or product manufacturer with any questions. Series DS-1 Dry-type Sprinklers must only be installed in fittings that meet the requirements of the Design Crite- ria section. Sprinkler Identification Numbers (SINs) 1Y3255— Pendent TY31 55- Upright 1Y3355 - Horizontal Sidewall Technical Data Approvals UL and C-UL Listed FM Approved VdS Approved TY3255 w/Standard Escutcheon only NYC Approved under MEA 352-01-E LPCB Approved Reference No. 094a/11 CE Certified Certificate of Conformity No. 0832- CPD-2015 (Refer to Tables A and B for details.) Maximum Working Pressure 175 psi (12,1 bar) Inlet Thread Connections 1 inch NPT ISO 7-A 1 Discharge Coefficient K=5.6 gpm/p5i112 (80,6 1pm/barl/2) Temperature Ratings Refer to Tables A and B. Finishes Sprinkler: Refer to Table D. Escutcheon: Refer to Table D. JANUARY 2015 Physical Characteristics Inlet.........................Copper Plug ........................Copper Yoke ..................Stainless Steel Casing ........Galvanized Carbon Steel Insert .......................Bronze Bulb Seat ..............Stainless Steel Bulb (5 mm dia.) ................Glass Compression Screw............Bronze Deflector.....................Bronze Frame.......................Bronze Guide Tube.............Stainless Steel Water Tube.............Stainless Steel Spring.................Stainless Steel Sealing Assembly.......Beryllium Nickel w/TEFLON Escutcheon .............Carbon Steel TFP500 TFP500 Page 2 of 10 SPRINKLER TYPE ESCUTCHEON TYPE TEMPERATURE RATING BULB COLOR CODE SPRINKLER FINISH NATURAL BRASS CHROME PLATED POLYESTER* STANDARD 135°F (57°C) Orange 1, 2, 3,4, 5, 6 1,2, 4, 5, 6 155-F (68-C) Red 175°F (79°C) Yellow 200°F(93°C) Green 286-F (141-C) Blue 360°F (182°C) Mauve 1, 2, 3, 6 1, 2, 6 PENDENT (TY3255) RECESSED 135°F (57°C) Orange 1,2,3 ,5 1,2,5 155-F (68'q Red 175°F (79°C) Yellow 200°F (93°C) Green 286°F (141°C) Blue 1,2 360°F (182°C) Mauve N/A DEEP 135°F (57°C) Orange 1,2,3,4,5 1,2,4,5 155-F (68-C) Red 175°F (79°C) Yellow 200°F (93°C) Green 286°F (141°C) Blue 360°F (182°C) Mauve WITHOUT 135°F (57°C) Orange 155°F (68°C) Red 175°F (79°C) Yellow 200°F (93°C) Green 286°F (141°C) Blue 360°F (182°C) Mauve 1, 2,3 1,2 UPRIGHT (TY3155) WITHOUT 135°F (57°C) Orange 1,2, 3, 4, 5 1, 2, 4, 5 155-F (68-C) Red 175°F (79°C) Yellow 200°F(93°C) Green 286°F (141°C) Blue 360°F (182°C) Mauve 1, 2, 3 1,2 Notes: Listed by Underwriters Laboratories, Inc. (UL), maximum order length of 48 inches Listed by Underwriters Laboratories for use in Canada (C-UL), maximum order length of 48 inches Approved by FM Global (FM Approvals), maximum order length of 48 inches Loss Prevention Certification Board (LPCB) and CE conformity apply to these temperature ratings only Approved by the City of New York under MEA 352-01 -E Approved by lidS * Frame and deflector only N/A - Not Applicable TABLE A SERIES DS-1 PENDENT & UPRIGHT DRY-TYPE SPRINKLERS, 5.6K, STANDARD RESPONSE LABORATORY LISTINGS AND APPROVALS TFP500 Page 3 of 10 SPRINKLER ESCUTCHEON TEMPERATURE BULB SPRINKLER FINISH NATURAL BRASS CHROME PLATED POLYESTER*** TYPE TYPE RATING COLOR CODE 135°F (57°C) Orange 155°F (68°C) Red STANDARD 175°F (79°C) Yellow 200°F (93°C) Green 286°F (141°C) Blue 360°F (182°C) Mauve 135°F (57°C) Orange 155°F(68°C) Red HSw* TY3355 DEEP 175°F (79°C) Yellow 1°, 2°°, 3*** 4 5 1°° 2**, 4,5 200°F (93°C) Green 286°F (141°C) Blue 360°F (182°C) Mauve 135°F (57°C) Orange 155-F (68-C) Red WITHOUT 175°F (79°C) Yellow 200°F (93°C) Green 286°F (141°C) Blue 360°F (182°C) Mauve 2°, 5 2°° Notes: Listed by Underwriters Laboratories, Inc. (UL), maximum order length of 48 inches Listed by Underwriters Laboratories for use in Canada (C-UL), maximum order length of 48 inches Approved by FM Global (FM Approvals), maximum order length of 48 inches Loss Prevention Certification Board (LPCB) and CE conformity apply to these temperature ratings only Approved by the City of New York under MEA 352-01-E * Horizontal sidewall with top of deflector-to-ceiling distance of 4 to 12 inches (100 to 300 mm) Light and ordinary hazard occupancies only Light hazard occupancies only Frame and deflector only TABLE B SERIES DS-1 HORIZONTAL SIDEWALL (HSW) DRY-TYPE SPRINKLER, 5.6K, STANDARD RESPONSE LABORATORY LISTINGS AND APPROVALS PLUG WITH INLET SEALING ASSEMBLY YOKE SPRING INLET BAND WATER TUBE CASING GUIDE INSERT TUBE BULB FRAME / SEAT/ 5 mm BULB ..- VENT HOLE _____ COMPRESSION DEFLECTOR SCREW FIGURE 1 SERIES DS-1 DRY-TYPE SPRINKLER, 5.6K, STANDARD RESPONSE ASSEMBLY WRENCH RECESS WRENCH V I FLAT PUSH WRENCH IN TO ENSURE ENGAGEMENT WITH SPRINKLER WRENCHING AREA FIGURE 2 W-TYPE 7 WRENCH TFP500 Page 4 of 10 SPRINKLER FITTING (REFER TO DESIGN CRITERIA SECTION) FACE OF SPRINKLER FITTING ORDER LENGTHS: 2-3/4" to 48" 1-3/4" DIA. (69,9 to 1219,2 mm) (44,5 mm) IN 1/4 (6,4 mm) INCREMENTS FACE OF CEILING 2-3/16":t 1/8" " DIA. (55,6 ± 3,2 mm) (76,2 mm) FIGURE 3 PENDENT (TY3255) WITH STANDARD ESCUTCHEON SPRINKLER FITTING (REFER TO DESIGN CRITERIA SECTION) FACE OF SPRINKLER FITTING ORDER LENGTHS: 3-3/4" to 48" (95,3 to 1219,2 mm) IN 1/4 (6,4 mm) 2-1/4 DIA. INCREMENTS (57,2 mm) FACE OF CEILING 1-3/8"± 1/8" 2-7/8" DIA. (34,9 ± 3,2 mm) FIGURE 4 PENDENT (TY3255) WITH STANDARD RECESSED ESCUTCHEON SPRINKLER FITTING (REFER TO DESIGN CRITERIA SECTION) FACE OF SPRINKLER FITTING ORDER LENGTHS: 3-1/2" DIA 1/2° to 46' h(88,g mm)°1 (12,7 to 1168,4 mm)' I I IN 1/4" (6,4 mm) I 2-1/2" DIA INCREMENTS FACE OF CEILING 4-1/4"± 1/8° (108,0 ± 3, 2 mm) FIGURE 5 PENDENT (TY3255) WITH DEEP ESCUTCHEON SPRINKLER FITTING (REFER TO DESIGN CRITERIA SECTION) FACE OF SPRINKLER FITTING ORDER LENGTHS: 5" to 48' (127,0 to 1219,2 mm) IN 1/4' (6,4 mm) INCREMENTS MINIMUM 1-3/4' (44,5 mm) DEFLECTOR TO CEILING FIGURE 6 PENDENT (TY3255) WITHOUT ESCUTCHEON TOP OF DEFLECTOR ORDER LENGTHS: 5' to 48" (127,0 to 1219,2 mm) IN 1/4"(6,4 mm) INCREMENTS FACE OF SPRINKLER FITTING SPRINKLER FITTING (REFER TO DESIGN CRITERIA SECTION) FIGURE 7 UPRIGHT (TY3155) WITHOUT ESCUTCHEON TFP500 Page 5 of 10 ORDER LENGTHS: 2-3/4 to 48" (69,9 to 1219,2 mm) IN 1/4' (6,4 mm) INCREMENTS 2-3/8" ± 1/8U (60,3 ± 3,2 mm) FACE OF ' FACE OF - - SPRINKLER MOUNTING FITTING SURFACE 30 DIA. T (76,2 mm) SPRINKLER FITTING 1 3,5 . (REFER TO DE mm) CENTERLINE 5/16' CRITERIA SECTION) OF WATERWAY (7,9 mm) FIGURE 8 HORIZONTAL SIDEWALL (TY3355) WITH STANDARD ESCUTCHEON ORDER LENGTHS: 1/2"t045-3/4"(12,7t01162,1 mm) IN 1/4" (6,4 mm) INCREMENTS 4-1/4" ± 1/80 ' 2-1/2" DIA.t FACE OF (108,0±3,2 mm) FACE OF (63,5 mm) MOUNTING SPRINKLER F- FITTING L[}a- 114ft= SPRINKLER FITTING (REFER TO DESIGN CENTERLINE 5/16" CRITERIA SECTION) OF WATERWAY (7,9 mm) FIGURE 9 HORIZONTAL SIDEWALL (TY3355) WITH DEEP ESCUTCHEON ORDER LENGTHS: 5-1/2' to 48" (139,7 to 1219,2 mm) IN 1/4" (6,4 mm) INCREMENTS MINIMUM 2-1/4" (57,2 mm) FACE OF I DEFLECTOR TO - SPRINKLER I MOUNTING URFACE SURFACE Oi1IIIIIIIIIIIIIIIIIIIIIIIIIIIIllr 5/16" / SPRINKLER FITTING (7,9 mm) (REFER TO DESIGN CENTERLINE CRITERIA SECTION) OF WATERWAY FIGURE 10 HORIZONTAL SIDEWALL (TY3355) WITHOUT ESCUTCHEON Operation When TYCO Series DS-1 5.61K Pendent, Upright, and Horizontal Sidewall, Stan- dard Response, Standard Coverage Dry-type Sprinklers are in service, water is prevented from entering the assembly by the Plug with Sealing Assembly (Ref. Figure 1) in the Inlet of the sprinkler. The glass bulb contains a fluid that expands when exposed to heat. When the rated temperature is reached, the fluid expands sufficiently to shatter the glass bulb, and the Bulb Seat is released. The compressed Spring is then able to expand and push the Water Tube as well as the Guide Tube outward. This action simultaneously pulls inward on the Yoke, withdrawing the Plug with Sealing Assembly from the Inlet, allow- ing the sprinkler to activate and flow water. Design Criteria TYCO Series DS-1 5.6K Pendent, Upright, and Horizontal Sidewall, Stan- dard Response, Standard Coverage Dry-type Sprinklers are intended for use in fire sprinkler systems designed in accordance with the standard instal- lation rules recognized by the applica- ble listing or approval agency (e.g., UL Listing is based on NFPA 13 require- ments). For more information on LPCB Approval, contact Tyco Fire Suppres- sion & Building Products at the follow- ing office: Kopersteden 1 7547 TJ Enschede The Netherlands Tel: +31-(0)53-428-4444 Fax: +31-(0)53-428-3377 Sprinkler Fittings Install 1 inch NPT Series DS-1 Dry-type Sprinklers in the 1 inch NPT outlet or run of the following fittings: malleable or ductile iron threaded tee fittings that meet the dimen- sional requirements of ANSI B16.3 (Class 150) cast iron threaded tee fittings that meet the dimensional requirements of ANSI B16.4 (Class 125) Do not install Series DS-1 Dry-type Sprinklers into elbow fittings. The Inlet of the sprinkler can contact the interior of the elbow. The unused outlet of the threaded tee is plugged as shown in Figure 12. TFP500 Page 6 of 10 Temperatures for Heated Area(1) Ambient Temperature 40°F 50°F 60°F Exposed to (4 C) (10 C) (16 C) Discharge End of Sprinkler Minimum Exposed Barrel Length(2), Inches (mm) 40°F (4°C) 0 0 0 30°F (-1°C) 0 0 0 20°F 4 0 0 (-7°C) (100) 10°F 8 1 (-12°C) (200) (25) 0°F 12 30 (-18°C) (305) (75) -10°F 14 4 1 (-23°C) (355) (100) (25) -20°F 14 6 3 (-29°C) (355) (150) (75) -30°F 16 8 4 (-34°C) (405) (200) (100) -40°F 18 8 4 (-40°C) (455) (200) (100) -50°F 20 10 6 (-46°C) (510) (255) (150) -60°F 20 10 6 (-51°C) (510) (255) (150) Notes: I. For protected area temperatures that occur between values listed above, use the next cooler temperature. 2. These lengths are inclusive of wind velocities up to 30 mph (18,6 kph). TABLE C EXPOSED SPRINKLER BARRELS IN WET PIPE SYSTEMS MINIMUM RECOMMENDED LENGTHS You can also install Series DS-1 Dry- type Sprinklers in the 1 inch NPT outlet of a GRINNELL Figure 730 Mechanical Tee and GRINNELL G-FIRE Figure 522; however, the use of the Figure 730 Tee and Figure 522 for this arrangement is limited to wet pipe systems. The configuration shown in Figure 13 is only applicable for wet pipe systems where the sprinkler fitting and water- filled pipe above the sprinkler fitting are not subject to freezing and where the length of the dry-type sprinkler has the minimum exposure length depicted in Figure 11. Refer to the Exposure Length section. For wet pipe system installations of 1 inch NPT Series DS-1 Dry-Type Sprin- klers connected to CPVC piping, use only the following TYCO CPVC fittings: 1" x 1" NPT Female Adapter (P/N 80145) 1" x 1" x 1" NPT Sprinkler Head Adapter Tee (P/N 80249) For dry pipe system installations, use only the side outlet of maximum 2-1/2 inch reducing tee when locating Series DS-1 Dry-type Sprinklers directly below the branchline; otherwise, use the configuration shown in Figure 12 to assure complete water drainage from above Series DS-1 Dry-type Sprin- klers and the branchline. Failure to do so may result in pipe freezing and water damage. NOTICE Do not install Series DS-1 Dry-type Sprinklers into any other type fitting without first consulting the Tyco Fire Protection Products (TFPP) Technical Services. Failure to use the appropriate fitting may result in one of the following: failure of the sprinkler to operate properly due to formation of ice over the Inlet Plug or binding of the Inlet Plug insufficient engagement of the Inlet pipe-threads with consequent leakage Drainage In accordance with the minimum requirements of the National Fire Pro- tection Association for dry pipe sprin- kler systems, branch, cross, and feed-main piping connected to Dry Sprinklers and subject to freezing tem- peratures must be pitched for proper drainage. Exposure Length When using Dry Sprinklers in wet pipe sprinkler systems to protect areas subject to freezing temperatures, use Table C to determine a sprinkler's appropriate exposed barrel length to prevent water from freezing in the con- necting pipes due to conduction. The exposed barrel length measurement must be taken from the face of the sprinkler fitting to the surface of the structure or insulation that is exposed to the heated area. Refer to Figure 11 for an example. For protected area temperatures between those given above, the minimum recommended length from the face of the fitting to the outside of the protected area may be determined by interpolating between the indicated values. Clearance Space In accordance with Section 8.4.9.2 of the 2010 edition of NFPA 13, when con- necting an area subject to freezing and an area containing a wet pipe sprinkler system, the clearance space around the sprinkler barrel of dry-type sprin- klers must be sealed. Due to tempera- ture differences between two areas, the potential for the formation of conden- sation in the sprinkler and subsequent ice build-up is increased. If this con- densation is not controlled, ice build-up can occur that might damage the dry- type sprinkler and/or prevent proper operation in a fire situation. Use of the Model DSB-2 Dry Sprinkler Boot, described in technical data sheet TFP591 and shown in Figures 14 and 15, can provide the recommended seal. TFP500 Page 7 of 10 FACE OF SPRINKLER -' FITTING Ir ' EXPOSURE LENGTH (SEE DESIGN DSB-2 CRITERIA INTENDED SECTION) FOR FREEZER STRUCTURES U(z -c FIGURE 11 EXPOSURE LENGTH SPRINKLER RUN OUTLET PLUGGED TO DRY SPRINKLER FITTING SYSTEM (SEE DESIGN SECTION) CRITERIA DSB-2 FOR FREEZER INTENDED STRUCTURES FIGURE 12 SPRINKLER FITTING UNHEATED AREA TO WET SIDE jIj SYSTEM -H I OUTLET PLUGGED tE1 DSB-2 SPRINKLER INTENDED I I FITTING FOR FREEZER (SEE DESIGN RITERIA STRUCTURES SCECTION) FIGURE 13 SPRINKLER FITTING HEATED AREA STRAP TIES (ENDS ON OPPOSING SIDES OF BOOT) DSB-2 BOOT ADHESIVE DIA. (44,5 mm) CLEARANCE HOLE INSULATED FREEZER STRUCTURE DS-1 SHOWN WITH STANDARD ESCUTCHEON FIGURE 14 MODEL DSB-2 DRY SPRINKLER BOOT WITH PENDENT SERIES DS-1 DRY-TYPE SPRINKLER 1-3/4" DIA. I (44,5 mm) I CLEARANCE INSULATED I HOLE FREEZER ADHESIVE I DSB-2 BOOT STRAP TIES DS-1 (ENDS ON SHOWN WITH OPPOSING STANDARD SIDES OF ESCUTCHEON BOOT) FIGURE 15 MODEL DSB-2 DRY SPRINKLER BOOT WITH SIDEWALL SERIES DS-1 DRY-TYPE SPRINKLER TFP500 Page 8 of 10 Installation TYCO Series DS-1 5.6K Pendent, Upright, and Horizontal Sidewall, Stan- dard Response, Standard Coverage Dry-type Sprinklers must be installed in accordance with this section. General Instructions Series DS-1 Dry-type Sprinklers must only be installed in fittings that meet the requirements of the Design Crite- ria section. Refer to the Design Criteria section for other important require- ments regarding piping design and sealing of the clearance space around the Sprinkler Casing. Do not install any bulb-type sprinkler if the bulb is cracked or there is a loss of liquid from the bulb. With the sprin- kler held horizontally, a small air bubble should be present. The diameter of the air bubble is approximately 1/16 inch (1,6 mm) for the 135°F (57°C) rating to 1/8 inch (3,2 mm) for the 360°F (182°C) rating. Obtain a leak-tight 1 inch NPT sprinkler joint by applying a minimum-to-maxi- mum torque of 20 to 30 lbs.-ft. (26,8 to 40,2 Nm). Higher levels of torque may distort the sprinkler Inlet with conse- quent leakage or impairment of the sprinkler. Do not attempt to compensate for insufficient adjustment in an Escutch- eon Plate by under or over-tightening the Sprinkler. Re-adjust the position of the sprinkler fitting to suit. Notes: Install pendent sprinklers only in the pendent position; install upright sprinklers only in the upright posi- tion. The deflector of a pendent or upright sprinkler is to be parallel to the ceiling. Install horizontal sidewall sprinklers in the horizontal position with their centerline of waterway perpendicu- lar to the back wall and parallel to the ceiling. Ensure the word "TOP" on the Deflector faces the ceiling. Step 1. With a non-hardening pipe- thread sealant such as TEFLON applied to the inlet threads, hand-tighten the sprinkler into the sprinkler fitting. Step 2. Wrench-tighten the sprinkler using either: a pipe wrench on the Inlet Band or the Casing (Ref. Figure 1) the W-Type 7 Sprinkler Wrench on the Wrench Flat (Ref. Figure 2) Apply the wrench recess of the W-Type 7 Sprinkler Wrench to the wrench flat. Note: If sprinkler removal becomes necessary, remove the sprinkler using the same wrenching method noted above. Sprinkler removal is easier when a non-hardening sealant was used and torque guidelines were followed. After removal, inspect the sprinkler for damage. Step 3. After installing the ceiling or wall and applying a ceiling finish, slide on the outer piece of the escutch- eon until it comes in contact with the ceiling/wall. Do not lift the ceiling panel out of its normal position. When using the Deep Escutcheon, hold the outer piece in contact with the mounting surface (ceiling or wall). Then rotate the inner piece approximately 1/4 turn with respect to the outer piece, to hold the Deep Escutcheon firmly together. Care and Maintenance TYCO Series DS-1 5.6K Pendent, Upright, and Horizontal Sidewall, Standard Response, Standard Cover- age Dry-type Sprinklers must be main- tained and serviced in accordance with this section. Before closing a fire protection system main control valve for maintenance work on the fire protection system that it controls, obtain permission to shut down the affected fire protection systems from the proper authorities and notify all personnel who may be affected by this action. Absence of the outer piece of an escutcheon, which is used to cover a clearance hole, may delay the time to sprinkler operation in a fire situation. A Vent Hole is provided in the Bulb Seat (Ref. Figure 1) to indicate if the Dry Sprinkler is remaining dry. Evidence of leakage from the Vent Hole indicates potential leakage past the Inlet seal and the need to remove the sprinkler to determine the cause of leakage; for example, an improper installation or an ice plug. Close the fire protec- tion system control valve and drain the system before removing the sprinkler. Sprinklers which are found to be leaking or exhibiting visible signs of corrosion must be replaced. Automatic sprinklers must never be painted, plated, coated, or other- wise altered after leaving the factory. Modified sprinklers must be replaced. Sprinklers that have been exposed to corrosive products of combustion, but have not operated, should be replaced if they cannot be completely cleaned by wiping the sprinkler with a cloth or by brushing it with a soft bristle brush. Care must be exercised to avoid damage to the sprinklers before, during, and after installation. Sprin- klers damaged by dropping, striking, wrench twist/slippage, or the like, must be replaced. Also, replace any sprin- kler that has a cracked bulb or that has lost liquid from its bulb (Ref. Installa- tion section). The owner is responsible for the inspection, testing, and maintenance of their fire protection system and devices in compliance with this document, as well as with the applicable standards of the National Fire Protection Asso- ciation (e.g., NFPA 25), in addition to the standards of any other authorities having jurisdiction. Contact the install- ing contractor or product manufacturer with any questions. Automatic sprinkler systems are rec- ommended to be inspected, tested, and maintained by a qualified Inspec- tion Service in accordance with local requirements and/or national codes. TFP500 Page 9 of 10 P/N* 60 - XXX - X - XXX SIN SPRINKLER ESCUTCHEON FINISH FINISH(1) Pendent with 96 TY3255 CHROME SIGNAL WHITE Standard Escutcheon (1" NPT) (Figure 3) o PLATED (RAL9003) 93 Pendent with TY3255 POLYESTER Deep Escutcheon (1° NPT) (Figure 5) SIGNAL WHITE - 1 NATURAL (RAL9003) Pendent with 97 TY3255 BRASS POLYESTER Recessed Escutcheon (1° NPT) (Figure 4) - 92 Pendent without TY3255 2 NATURAL BRASS Escutcheon (1° NPT) (Figure 6) BRASS PLATED SIGNAL WHITE SIGNAL WHITE 4 (RAL9003) (RAL9003) POLYESTER POLYESTER CHROME CHROME PLATED PLATED I TEMPERATURE I ORDER RATING(2) LENGTH(3) 98 Upright without I TY3155 I - - ________________ I Escutcheon (1° NPT) (Figure 7) 0 135°F (57°C) Notes: 1 155°F (68°C) 1 Escutcheon Finish applies to sprinklers provided with escutcheons. 360'F (182°C) temperature rating applies to non-recessed sprinkler assemblies. 2 175°F (79°C) Dry-type Sprinklers are furnished based upon 'Order Length" as mea- sured per Figures 3 through 10, as applicable, and for each individual 3 200°F (93°C) sprinkler where it is to be installed. After the measurement is taken, round it to the nearest 1/4 inch increment. * Use Prefix "I" for ISO 7-A 1 Connection (e.g., 1-60-961-1-180). 4 286°F (141°C) 5 360°F(182°C) TABLED SERIES DS-1 DRY-TYPE SPRINKLERS, 5.6K, STANDARD RESPONSE PART NUMBER SELECTION Sidewall with TY3355 94 Standard Escutcheon (1° NPT) (Figure 8) 53 Sidewall with TY3355 Deep Escutcheon (1° NPT) (Figure 9) 54 Sidewall without TY3355 Escutcheon (1° NPT) (Figure 10) 055 5.50° 082 8.25" 180 18.00" 187 18.75" 372 37.25" 48.00" 480 Limited Warranty For warranty terms and conditions, visit www.tyco-fire.com. Ordering Procedure Contact your local distributor for avail- ability. When placing an order, indi- cate the full product name, including description and part number (P/N). Dry-type Sprinklers When ordering Series DS-1 5.6K Pendent, Upright, and Horizontal Side- wall, Standard Response, Standard Coverage Dry-type Sprinklers, specify the following information: SIN: TY3255 - Pendent 1Y3155 - Upright TY3355 - Horizontal Sidewall Order Length: Dry-type Sprinklers are furnished based upon Order Length as mea- sured per Figures 3 through 10, as applicable. After the measurement is taken, round it to the nearest 1/4 inch increment. Inlet Connections: 1 Inch NPT (Standard) ISO 7-R 1 (For information on ISO Inlet Thread Connections, contact your Tyco Sales Representative.) Temperature Rating Sprinkler Finish Escutcheon Type and Finish, as applicable P/N from Table 0 Part numbers are for 1 inch NPT standard order sprinklers. Orders for all other sprinkler assemblies must be accompanied by a complete description. Sprinkler Wrench Specify W-Type 7 Sprinkler Wrench, P/N 56-850-4-001 Sprinkler Boot Specify Model DSB-2 Dry Sprinkler Boot, P/N 63-000-0-002 This part number includes one (1) Boot, two (2) Strap Ties, and 1/3 oz. of Adhe- sive (a sufficient quantity for installing one boot). TFP500 Page 10 of 10 GLOBAL HEADQUARTERS 1 1400 Pennbrook Parkway, Lansdale, PA 19446 I Telephone +1-215-362-0700 Copyright © 2015 Tyco Fire Products, LP. All rights reserved. tqco TEFLON is trademark of the DuPont Corporation. Fire Protection Products Malleable Iron Threaded Pipe Unions Pressure - Temperature Ratings Temperature Pressure ____________ ass 250 Class 300 (°F) (°C) Class 150P500 psi bar bar psi bar .200 to 1500 -28.90 to 65.60 300 20.7 34.5 600 41.4 2000 93.30 265 18.3 455 31.4 550 37.9 2500 121.10 225 15.5 405 27.9 505 34.8 3000 148.90 185 12.8 360 24.8 460 31.7 3500 176.70 150 10.3 315 21.7 415 28.6 4000 204.40 110 7,6 270 18.6 370 25.5 4500 232.20 75 5.2 225 15.5 325 22.4 5000 260.00 - - 180 12.4 280 19.3 5500 287.80 - - 130 9.0 230 15. Note: Unions with Copper or Copper Alicy seats are not intended for use where temperature exceeds 450°F c®Us APPROVED For Listings/Approval Details and Limitations, visit our website @ www.anvilintl.com or contact an Anvil/AnvilStar Sales Representative. Malleable Iron Threaded Fittings Pressure - Temperature Ratings Temperature Pressure Class 150 Class 300 __________ Sizes ¼-i" (6-25 mm) Sizes 11/4"-2" 1 (32-51 mm) Sizes 21/2 '-3' (64-76 mm) (°F) (°C) psi bar psi bar psi bar psi bar -20° to 1500 28.90 to 300 20.7 2,000 65.60 137.9 1,500 103.4 1,000 68.9 2000 93.3 265 18.3 1,785 123.1 1,350 93.1 910 62.7 2500 121.1 225 15.5 1,575 108.6 1,200 82.7 825 56.9 3000 148.9 185 12.8 1,360 93.8 1,050 72.4 735 50.7 3500 176.7 150 10.3 1,150 79.3 900 62.1 650 44.8 4000 204.4 - - 935 64.5 750 51.7 560 38.6 4500 232.2 - - 725 50.0 600 41.4 475 32.8 5000 260.0 - - 510 35.2 450 31.0 385 26.5 5500 287.8 - - 300 20.7 300 20.7 300 20.7 0 Anvil Class 150/300 Malleable Iron Fittings conform to ASME j B16.3 and Unions conform to ASME B16.39. ALL ELBOWS & TEES %" (10 ON) and LARGER ARE 100% GAS TESTED AT A MINIMUM OF 100 PSI. (6.9 bar) www.anvilintl.com 17 0p9V TO CO4 ThEr best sprinkler pi in the industry! ' c®us LISTED <> APPROVED ONFSA NFPA SP BULL MOOSE TUBE COMPANY /I A I ~ -- - ~~- ~-- I'SLI-I I-JhII TAI ff JLJ -I-I_J L;IJIvui Bull Moose Tube® is a customer focused, growth oriented manufacturer and marketer of tubular products, where success is based on a commitment to meeting the customer's perception of quality. Our strength resides in our people working together to satisfy customers and to promote business growth by achieving superior financial performance. wwwBulIMooseTube.com sales@bullmoosetube.com -800 325 4467 c®us LISTED <> APPROVED NFPA := w - BULL MOOSE TUBE COMPANY Bull Moose Tube's® "Eddy Pipe®" brand sprinkler pipe is produced to meet sprinkler pipe standards and applications. c®us LISTED <9> APPROVED Mo A z4 ONFSA NFPA ADVANTAGES OF BULL MOOSE TUBE® EDDY PIPE® FAMILY All pipe products are UL Listed (for U.S. and Canada), and have been approved by Factory Mutual. excellent production and coating capabilities, tighter tolerances, and our unique steel properties make our pipe excellent for roll grooving, welding, threading, and plain end fittings. All products are certified to ASTM Al 35 and A795 Type E, Grade A. Available in specific cut to order lengths from regular mill rollings. More popular sizes available with coating or bare. Ultra Eddy®, Eddy Flow®, Eddylite®, and Eddythread 40® offer cost savings along with superior hydraulics without compromising service life. Sprinkler pipe inventory stocked in Masury, Ohio; Gerald, Missouri; Casa Grande, Arizona; Kent, Washington; and Dallas, Texas. All Bull Moose (black) sprinkler pipe includes our exclusive EDDY GUARD Il® MIC preventative coating. Bull Moose Tube® sprinkler pipe is FBCTM compatible. PRODUCTS Schedule 10 and Schedule 40: FM approved and UL listed sprinkler pipe. Eddythread 40®: Light threadable Schedule 40 replacement with corrosion resistance ratio of 1.0. Eddylite®: Lightwall threadable with standard outside diameter. Eddy Flow®: Cost effective replacement for Schedule 10. Ultra Eddy®: Lightwall roll groovable pipe. Bull Moose galvanized steel sprinkler pipe is hot dipped galvanized to meet ASTM Al 23 standards. All products are stencilled to meet FM & UL specifications. PROTECTION Eddy Guard Il®: Bull Moose Tube® is producing product that can resist bacteriological growth even after multiple rinse-outs. You know MIC corrosion can impact your installation and your property. Specify Bull Moose Tube® "Eddy Guard Il®" and feel comfortable knowing that you are getting Eddy Pipe® product you trust with the bacteria resistance you need. Eddy Guard Il® is NFPA 13 and NFPA 13R system compatible for use in hybrid systems as well as FM approved. All information contained herein is accurate as known at the time of publication. Bull Moose Tube® reserves the right to change product specifications without notice and without incurring obligation. LI LI Bull Moose Tube's® Schedule 10 and Schedule 40 are FM Approved and UI Listed (for U.S. and Canada) even though these products do not require separate approvals and listings. Bull Moose Tube riade the decision to have them approved and listed Our Schedule 10 and Schedule 40 have a pressure rating of 300 PSI and have been through the some rigorous testing as our other tine pipe products Schedule 10 can be supplied roll grooved or plain end Bull MooeTube's® Schedule 10 and Schedule 40 pipes are hot dipped galvanized to meet ASTM Al 23 standards All products are stencilled to meet FM & UL speuficalioiis..;. . c®us LISTED <8> APPROVED no /4 ONFSA NFPA El SCHEDULE 10 PIPE SPECIFICATIONS NOMINAL PIPE O.D. I.D. WATER FILLED BUNDLE SIZE (IN) (IN) (IN) CRR** WEIGHT/FT WEIGHT SIZE 1.315 1.097 15.27 1.41 lbs/ft 1.820 91 - 991 181Ibs/tt 2518 61"j 1-1/2 1.900 1 682 Y.76 2.09 lbs/ft 3.053 61 2.375 /1 2.157 627 2.94 lbs/ft 4223 11 J 2-1/2 2.875 2.635 4.92 3.53 lbs/ft 5.893 30 3 T1L 3.500 1E1Q ]Li T4iT.T -4.34 l bs/ft :1 4260 250 5.62 lbs/ft 11796 - 19 SCHEDULE 40 PIPE SPECIFICATIONS NOMINAL PIPE O.D. I.D. WATER FILLED BUNDLE SIZE (IN) (IN) (IN) CRR** WEIGHT/FT WEIGHT SIZE 1 1.315 - 1.049 100 168 lbs/ft 2.055 70 11#4 1660 L _1 00 Jlb/1EJE2918 1-1/2 1.900 1.610 - 1.00 2.72 lbs/ft 3.602 44 2 30 21/2* 2875 2468 100 5.80 lbs/ft 7.875 30 - -- 3.5( [ 3 TjL 100 758iUftJ10783 19 - 4* -4 500 4.026 _100 10.80 lbs/ft 2 L__ 16.316 19 *Only available in Casa Grande, AZ **Corrosion Resistance Ratio per latest UL Directory Listing PIPE PREPARATION For proper operation, all pipe surfaces should be cleaned prior to installation. In order to provide a leak-tight seat for the gasket, pipe surfaces should be free from indentations and projections from the end of the pipe to the groove. All loose paint, scale, dirt, chips, grease, and rust must be removed prior to ulstallation. Failure to lake these important steps rsray result in improper coupling assembly, causing leakage. Also, check the manufacturer's instructions for the specific fitting used. A For Additional Information Contact (800) 325-4467 www.bullmoosetube.com , Lo Or From Canada Call: (800) 882-4666 sales@bullmoosetube.com 8 1819 Clarkson Road Chesterfield, MO Gerald, MO Kent, WA Casa Grandel AZ Dallas TX Masury, OH CULL MOOSE rUSE COIVIPANV 63017 FireLock® Outlet-I ® ILPCBI SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS STYLE 922 The Style 922 Outlet-T provides a convenient method of incorporating ½, 3/4, and 1'/15, 20 and 25mm outlets for directly connecting sprinklers, drop nipples, sprigs, gauges, drains and other outlet products. Available for 11% through 76.1 mm/32 to 76.1 mm piping systems, Style 922 outlets are UL/ULC Listed, LPCB and FM Approved for branch connections and VdS Approved for direct sprinkler connection only on wet and dry systems. The locating collar engages into the hole prepared in the pipe. When tightened, the assembly compresses the gasket onto the OD of the pipe. The Style 922 Outlet-T is UL/FM rated up to 300 psi/2068kPa and VdS rated up to 16 bar at the ambient temperatures typical for fire protection systems. Style 922 is suitable for use on standard, lightwall, Schedule 5 and other specialty pipes.* Contact Victaulic for other optional coatings. *Consult Section 10.01 for specific listings/approvals. MATERIAL SPECIFICATIONS Housing: Ductile iron conforming to ASTM A-536, grade 65-45-12. Ductile iron conforming to ASTM A-395, grade 65-45-15, is available upon special request. Gasket: Grade "E" EPDM - Type A (Violet color code). FireLock products have been Listed by Underwriters Laboratories Inc. and Approved by Factory Mutual Research for wet and dry (oil free air) sprinkler services up to the rated working pressure using the Grade "E" Type A Gasket System. Bolts/Nuts: Heat-treated plated carbon steel, trackhead meeting the physical and chemical requirements of ASTM A-449 and physical requirements of ASTM A-183. Housing Coating: Orange enamel (North America, Latin America, Asia Pacific) Red enamel (Europe) JOB/OWNER CONTRACTOR ENGINEER System No. Submitted By Spec Sect Para Location Date Approved Date www.victaulic.com vicuuc IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2009 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REV C STYLE 922 DIMENSIONS _. !_Mj UE; IPS CARBON STEEL PIPE - HOLE CUT PRODUCTS iU.3 Fire Lock® Outlet-I Nominal Size inches/mm Diameter Hole Dimensions I inches/millimeters X. eig Each 1 1/4 1h 1 /I6 130 1.83 1.10 3.87 2.56 1.0 32 15 30.2 33.0 46.5 27.9 98.3 65.0 0.45 '/4 13A6 1.28 1.83 1.10 3.87 2.56 1.1 20 30.2 32.5 46.5 27.9 98.3 65.0 0.50 1 1 3/3 1.52 2.18 1.10 3.87 2.56 1.2 25 30.2 38.6 55.4 27.9 98.3 65.0 0.54 11/2 ½ 13Ao 1.42 1.95 1.22 4.08 2.56 1.2 x 40 15 30.2 36.1 49.5 31.0 103.6 65.0 0.54 3/4 13A6 1.40 1.95 1.22 4.08 2.56 1.2 20 302 35.6 49.5 31.0 103.6 650 0.54 13A6 1.64 2.30 1.22 4.08 2.56 1.3 25 30.2 41.7 58.4 31.0 103.6 65.0 0.59 2 ½ 13A6 1.66 2.19 1.46 4.60 2.56 1.3 50 15 30.2 42.2 55.6 37.1 116.8 65.0 0.59 '/4 13A6 1.64 2.19 1.46 4.60 2.56 1.4 20 30.2 41.7 55.6 1 37.1 116.8 65.0 0.64 1 13A6 1,88 2.54 1,46 4.60 2.56 1.5 25 30.2 47.8 645 37.1 116.8 65.0 0.68 2½ ½ / 14 1.91 2.44 1.71 5.40 2.56 1.6 x 65 15 30.2 48.5 62.0 43.4 1372 650 0.73 3/4 1 /6 1.89 2.44 1.71 5.40 2.56 1.6 20 30.2 48.0 62.0 43.4 137.2 65.0 0.73 1 1/6 2.13 2.79 1.71 5.40 2.56 . 1.6 25 30.2 54.1 70.9 43.4 137.2 65.0 0.73 ½ 1 3A6 1,91 2.44 1.71 5.50 2.56 1.6 76.1 mm X 15 30.2 48.5 1 62.0 43.4 139.7 65.0 0.73 3/4 1/I6 1.89 2.44 1.71 5.50 2.56 1.6 20 30.2 48.0 62.0 43.4 139.7 65.0 0.73 - 1 1 1/16 2.13 2.79 1.71 5.50 2.56 1.7 25 30.2 54.1 70.9 43.4 139.7 65.0 0.80 t Victaulic female threaded products are designed to accommodate standard NPT or BSPT (optional) male pipe threads only. Use of male threaded products with special features, such as probes, dry pen- dent sprinklers, etc., should be verified as suitable for use with this Victaulic product. Failure to verify suitability in advance may result in assembly problems or leakage. Center of run to engaged pipe end for NPT threads (dimensions are approximate). www.victaulic.com vICTAuLIC IS A REGISTERED TRADEMARK OF VIC1'AULIC COMPANY. © 2009 vicTAuLic COMPANY. ALL RIGHTS RESERVED. 10.52 2 \ 4tauIic REV r IPS CARBON STEEL PIPE - HOLE CUT PRODUCTS FireLock® Outlet-I STYLE 922 PERFORMANCE Equivalent Length of 1 inch Schedule 40 Steel Pipe (per UL Run Size x Outlet Size 213, Section 16) (C=120)*, FT /mm Ft/iters 32 25 11/2 x 40 25 8.5 2.6 21/2 x 65 25 2.6 L1•.iiuiiuuuui -- - --________ * Hazen-Williams coefficient of friction is 120 www.victaulic.com A_Cta_ulic~ VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2009 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PFV ( 10.52 3 FireLock® Outlet-I STYLE 922 INSTALLATION Reference should always be made to the 1-100 Victaulic Field Installation Handbook for the product you are installing. Handbooks are included with each shipment of Victaulic products for complete installation and assembly data, and are available in PDF format on our website at www.victaulic.com. WARRANTY Refer to the Warranty section of the current Price List or contact Victaulic for details. NOTE This product shall be manufactured by Victaulic or to Victaulic specifications. All products to be installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations. For complete contact information, visit www.victaulic.com A_C_tau_hc~ 10.52 3355 REV G UPDATED 12/2009 vICTAULIC IS A REGISTERED TRADEMARK OF vIcTAuLIc COMPANY. © 2009 vicTAuLic COMPANY. ALL RIGHTS RESERVED, 10.52 FAcn P.O. Box 3365 South El Monte, CA 91733 626.444.0541 Fax 626.444.3887 www. Afcon.org 300 RING HANGER I thru 4 Inch pipe LISTED FOR STEELJCPVC 1/2 & 3/4 inch pipe 5 thru 8 inch pipe SIZE - ROD- 3/8" or 1/2" SIZE - SYSTEM PIPE - 1/2" thru 8" MATERIAL - Carbon Steel, Mil. Galvanized to G-90 spec. LISTING/APPROVAL - I:@ us USTED 203-EX 2551 1"- 8" Approval guide - 1"- 8" OSHPD OPA-0601 See Website. CONFORMS WITH: Federal Specification WW-H-171E, Type 10. Manufacturers Standardization Society ANSI/MSS-SP-58 Type 10. MAXIMUM TEMPERATURE - 650°F. FUNCTION - Pipe hanger component of an AFCON hanger. To support steel, CPVC or copper pipe. INSTALLATION - Per NFPA 13, 13R, 13D, these instructions and the CPVC or copper pipe manufacturers instructions. FEATURES - * Sized and listed exclusively for use with #310 Surge Restrainer. * Band edge is offset for EASY pipe insertion. * Custom fit swivel nut for better retention in ring. ORDERING - Part #, pipe size. 11/09 NFPA 13 PIPE ROD I WI. 5 WT.+250 UL TEST LOAD 1 3/8 3075 403.75 750 11/4 3/8 43.95 469.75 750 11/2 3/8 54.15 520.75 750 2 3/8 76.95 634.75 750 21/2 3/8 118.35 1 841.75 850 3 3/8 162.30 1061.50 1050 4 3/8 246.00 1480.00 1500 5 1/2 349.45 1996.75 2000 6 1/2 476.35 2631.75 2650 8 11/2 711.00 3805.00 4050 551 P.O. Box 3365 South El Monte, CA 91733 626.444.0541 Fax 626.444.3887 www. Afcon.org 310 RING RESTRAINER Restraint SIZE - One size fits 3/4 thru 2 inch AFCON #300 Ring Hanger. MATERIAL - Carbon Steel. FINISH - Mu. Galvanized. LISTINGS - Yi. us 203-EX 2551 Listed only for use with AFCON #300 Ring Hanger. FUNCTION - To restrain movement of sprinkler pipe toward the knurl nut of the ring hanger. To prevent upward movement of pipe that supplies a pendent sprinkler below the ceiling. INSTALLATION - Per NFPA 13 and CPVC manufacturers instructions on steel, CPVC, or copper pipe. Snap into locking position on swivel nut of AFCON #300 Ring Hanger. SPECIAL NOTE: When installing on CPVC sprinkler system pipe: Verify that all assembly components are cleaned of any surface oil. FEATURES - * Listed only for use with AFCON #300 Ring Hanger. ORDERING - Part # and size. Specific AFCON products are exclusively designed to be compatible ONLY with other AFCON products including parts and fasteners, resulting ins listed sway brace, restrainer or hanger assembly. Be advised the following warranty restriction will apply. DISCLAIMER - AFCON will NOT warrant against the failure of its products when used in combination with other products, parts or systems not manufactured or sold by AFCON. AFCON shalt NOT be liable under any circumstances whatsoever for any direct or indirect, incidental or consequential damages of any kind, including but not limited to loss of business or profit, when non-AFCON products have been, or are used. 1/08 n Product Features No pre-ddlling required. Quick to install using the Sammy Nut Driver with an 18V cordless drill/driver. Saves time from traditional methods. Reduces installation cost. Made in the U.S.A. IUU dR pprovalSI,.Nh F Módëll I - ' .-,_.__•a,- ". "-' 1/4" 8002957 GST 100 1/4 x1" 210 (7/16"OSB) 25 125 1/4"8003957 GST 200 1/4x2" 1760(Fir)25 125 11111 1/4 8004957 CST 300 1/4 -x3- - 00 (9) 25 3/8 8006957 GST .75 1/4x3/4 564 (3/4" Ply) 25 125 #14 Nut ICel Part #8113910 3181,8007957 GST 10 1/4 x1" 300 25 12] 3/8" 8008957 GST 20 1/4x2" 1760 (Fir) 850 1475 25 125 3/8 8068925 GST 20-SS 1/4x2" 1760 (Fir) 850 25 125 "1 3/8" 8009925 GST 25-380 3/8 x 2-1/2" 2113 (Fir) 1500 25 125 8010957 GST 30 1/4x3 2060 (Fir) 1500 1475 25 125_ 3/8" 8069925 GST 30-SS 1/4 x 3" 2060 (Fir) 25 125 3/8 8011925 GST 40 1/4x4" 2180 (Fir) 25 125 ] 3/8" 8012925 GST 60 1/4x6" 2230 (Fir) 25 125 - 1/2_8013925 GST 2 t/4x2__1760Ar) 25125 #14SWRed 1/2" 8014925 GST 2.5-380 3/8x2-1/2" 2113 (Fir) 25 125 1/2" 8015925 GST3 1/4x3" 2275 (Fir) 25 125 1/2" 8016925 GST4 1/4x4" 2180 (Fir) 25 125 1/2__8017925 GST 6 1/4x6 2230 (Fir) 25 1251 Nut Driver Part #8114910 Product Features Eliminates distortion of threaded rod. • Saves time from traditional methods. "Accommodates up to 3 '/" x 12 pitch roof. • Reduces installation cost. -=.-"-\ Allows IT deflection from vertical. Made in the U.S.A. I 3/8___8139957_JH.GST20_1/4 x2_1257(f)1050 1475 25125125J -' 3/8 8141957 SH-GST 30 1/4 a 3" 1720 (Fir) 1500 1475 25 125 1#14 Black Nut Driver SPECIAL NUT DRIVER SYSTEM: The nut drivers were designed with a unique spin-off feature which provides a fast and safe installation each time. When the face of the driver comes into Part #8113910 contact with the material you are installing into, continue drilling until nut driver spins free. Installation is then complete. Warranty requires the use of the appropriate nut driver for installations. I Not less than 2' nominal width /, - _.. . Product Features (1.1/2*) up to 3-1/2' pipe; not less than - * .. No pre-drilling required. 3" (2.1/fl nominal width 4' & 5" pipe 4 ) Floor Joist •. Quick to install using the Sammy Minimum 2-1/2' from bottom for branch lines Minimum 3" from .,. Nut Driver with an 18V cordless I ) bottom for main lines. Exception: This dri(l/dver. requirement shall not apply to 2' or / ) 1 thicker nailing ships resting on top of steel beams. Saves time from traditional methods. Reduces installation cost. ., Made inthe U.S.A. #14 SW Red Nut Driver Part #8114910 aim 1/4" 8018957 SWG 100 1/4x1" 622JFir) 25 125 1/4" 8019957 SWG 200 1/4 x 2" 1725 (Fir) 25 125 3/8" 8020957 SING 10 1/4 xl" 622 (Fir) 300 25 125] . 3/8" 8021957 SWG 20 1/4 x 2" 1725 (Fir) 1050 25 125 3/8" §073925 $WG 20-SS 1/4 L2 1725 (Fir) 850 25 125 /.. 3/8" 8022925 SWG 25-380 3/8 x 2-1/2' 2249 (Fir) 1500 25 125 /g' 111t232n sWr 30 1/403" 1884 (Fir) 25 125 1 I STEEL:] I1 T INTO WOOD&STEEL] Insert the appropriate nut driver into a 3/8" or 1/2" portable drill. Insert the SAMMYS into the #14 (black) nut driver (p/n 8113910). Drill should be in a vertical position. Push the face of the nut driver tight to the member. When the nut driver spins freely on the SAMMYS, stop drill and remove. The SAMMYS is now ready to receive 1/4", 3/8' 1/2" or metric all thread rod, bolt stock. (The 1/2" requires the #I4SW red nut driver) Note: When installing DSTR, follow the above instructions, then add retainer nut and torque to 20 foot lbs. for maximum pullout in puriln steel. BIC Ji(P:!J(0,00-ml I. Insert the appropriate nut driver into a 3/8" or 1/2"portable drill. Insert the SAMMYS into the #14S W (red) nut driver (p/n 8114910). With drill unit in a horizontal position and at a right angle to the structural member, begin installation. When the nut driver spins free on the SAMMYS, stop the drill and remove. The unit is now ready to receive 1/4", 3/8" or metric all thread rod or bolt stock. Note: When installing SWDR, follow the above instructions, then add retainer nut and torque to 20 foot lbs. for maximum pullout in purlin steel. SPECIAL NUT DRIVER SYSTEM: The nut drivers were designed with a unique spin-off feature which provides a fast and safe installation each time. When the face of the driver comes into contact with the material you are installing into, continue drilling until nut driver spins free. Installation is then complete. Warranty requires the use of the appropriate nut driver for installations.