HomeMy WebLinkAbout6185 PASEO DEL NORTE; 100; FPC2021-0096; PermitPERMIT REPORT
(City of
Carlsbad
Print Date: 08/09/2021 Permit No: FPC2021-0096
Job Address:
Permit Type:
Parcel #:
Valuation:
Occupancy Group:
#of Dwelling Units:
Bedrooms:
Bathrooms:
6185 PASEO DEL NORTE, # 100,
FIRE-Construction Commercial
2110401800
$236,422.16
CARLSBAD, CA 92011-1152
Work Class: Fire Alarm
Track #:
Lot U:
Project U:
Plan U:
Construction Type:
Orig. Plan Check U:
Plan Check U:
Status: Closed - Finaled
Applied: 06/07/2021
Issued: 07/22/2021
Finaled Close Out: 08/09/2021
Inspector:
Final Inspection:
Project Title:
Description: TRI-CITY HEALTH -INSTALL NEW PAD-4 POWER SUPPLY NEXT TO EXISTING SIEMENS CONVENTIONAL FIRE ALARM PANEL
Applicant: FPContractor:
SIEMENS SIEMENS INDUSTRY INC
CHRIS BISCHEL P0 BOX 80600
10100 WILLOW CREEK RD INDIANAPOLIS, IN 46280-0600
SAN DIEGO, CA 92131-1636 (630) 857-2100
(858) 265-9894
FEE AMOUNT
FIRE TI Fire Alarm System $620.00
Total Fees: $620.00 Total Payments To Date: $620.00 Balance Due: $0.00
Fire Department Page 1 of 1
1635 Faraday Avenue, Carlsbad CA 92008-7314 1 760-602-4665 1 760-602-8561 f I www.carlsbadca.gov
-
TRI-CITY HEALTH
FIRE ALARM T.I.
6185 PASEO DEL NORTE, SUITE 100
CARLSBAD, CA 92011
Siemens Project #:
440P-312792
Date:
June 1, 2021
Rev: 01
SIEMENS Data Sheet
Fire Safety Products
FACP Accessories
PAD-4 Distributed Power Supply Unit [for ®UL markets]
Notification Appliance Circuit Extender
Models PAD-4-ENCL, PAD-4-MB (with FP20II-1.1I, FP2012-UI power supplies)
ARCHITECT AND ENGINEER SPECIFICATIONS
. Four (4) 'Class B', power-limited notification appliance circuits (NACs)
'Class A', field-selectable wiring
Each unit can support an optional module (Model PAD-4-CLSA) that
converts two (2) built-in 'Class A' NACs into four (4) 'Class A' NACs
Up to 3 Amps of auxiliary-power output
Optional built-in strobe synchronization
Supports coded audible signals, including Temporal 3, Temporal 4 patterns
Battery supervision and control
'Form C' general Trouble I AC Fail monitoring contact
'Class A'
Adapter Card
[Model PAD-4-CLSA)
Power supplies support NAC power
Up to 6A used with Model FP2011-Ui
Up to 9A used with Model FP2012-Ui
24VDC output voltage
Ground-fault detection
Advanced microprocessor control
Uses Flash memory-based system firmware
Optional system-diagnostic and firmware-upgrade tool
Product Overview
Used with Siemens - Fire Safety fire alarm control
panels (FACPs), the Distributed Power Supply PAD-4
Unit is a NAC expander with a built-in, auxiliary-
power output. Each PAD-4 unit distributes
additional power in buildings for audible and visual
indicators that conform to the Americans with
Disabilities Act (ADA). PAD-4 also has the
following features:
NACs
Signal-input circuits
Battery-charging circuit
Trouble relays for remote monitoring
Diagnostic light-emitting diodes (LEDs)
Alternating Current (AC) power connection
The Siemens NACs, which connect with alarm
signaling devices, have been designed to provide
the highest level of reliability and performance.
Signal coding on the circuits is accomplished
through integrated circuits (rather than relays),
which eliminates mechanical wear on the output
circuits.
Main Board Unit Enclosure
[Model PAD-4-MB] [Model PAD-4-ENCLI
Multi-module mounting in System 3 enclosures
Multiple modules share battery set
ADA Compliant
®UL 864 9th Edition Listed, ®UL 1481 Listed;
FM (3010), CSFM (7315-0067:0268) Approved
The PAD-4 unit provides constant 24VDC output
voltage to each NAC - independent of voltage
fluctuations on the primary or secondary power
source. As a result, a larger voltage drop and a
greater wire length for each NAC are supported by
each PAD-4.
Specifications
This version of the Siemens Distributed Power Supply
Unit can be configured in the following manner that
makes the outputs easily programmable:
'STEADY' outputs
Synchronized strobe outputs
American National Standards Institute (ANSI) Temporal 3
ANSI Temporal 4 [for carbon monoxide (CO) alarm signal]
There are also two (2) inputs used to control the
activation of the four (4) outputs. Programming can
be set so one (1) input will silence the audible signal
on Siemens Models 'AS'-series, 'NS'-series, or 'ZH'-
series horn and horn-strobes while the strobes
remain active.
Distributed Power Supply— NAC Extender (Model PAD-4 series) 3363
SIEMENS Industry, Inc.
Building Technologies Division
Specifications - (continued)
Operation of each PAD-4 unit is controlled by
firmware stored in Flash memory on the main board,
as well as the storage of a 10-event log, which can
be viewed via Model PAD-4-FDT. In the event that
an upgrade to the system firmware is required, the
firmware can be transferred to the system without
the replacement of firmware chips.
An optional firmware-download software tool,
Model PAD-4-FDT, can be used for system-
diagnostic testing of the following:
Primary-power voltage readouts
Current draw for power charger
Configuration switch settings
Firmware version
Battery voltage
When the tool is in communication with Model PAD-
4-MB, the 'Test Mode' LED is illuminated. Model
PAD-4-LUA is a USB serial port adapter that is
required for tool-kit operation.
Each NAC extender supervises a variety of functions
including:
Low AC power
Battery-voltage level
Earth ground-fault conditions
All power can be directed to two (2) 'Class A' or four
(4) 'Class B' power-limited NACs. Each NAC supports
up to 3 Amps per circuit. Either one (1) or two (2)
inputs can control four (4) outputs, which are
compatible with all Siemens - Fire Safety 24VDC
alarm signaling devices.
In cases where 'Class A' circuits are used, an optional
Model PAD-4-CLSA module can be added, providing
two (2) additional 'Class A' outputs to each PAD-4
unit.
Each NAC extender is also capable of operating other
parts of a Siemens fire alarm system, such as door
holders, via 3 Amps @ 24VDC max of power-limited
auxiliary output. When the output activated, the
total power available cannot exceed 6 Amps when
used with Models FP2011-U1 or 9 Amps when used
with FP2012-U1.
Trouble conditions are monitored through each
unit's two (2) inputs. In addition, one (1) 'Form C'
Trouble contact is provided for monitoring each unit
that is connected through the input of a Siemens
FACP. Therefore, the user has the option of
connecting a PAD-4 NAC extender unit into a NAC of
a Siemens FACP, or the unit may be monitored with
a Model TRI-series monitoring module on a Siemens
intelligent fire system.
A separate 'Form C' Trouble contact is used
exclusively with each NAC extender to indicate AC
Fail Trouble events on the NAC extender.
SIEMENS Industry, Inc.
Building Technologies Division
Each unit is packaged in its own sheet-metal
enclosure with sufficient space to house up to 7AH
battery sets. The enclosure (Model PAD-4-ENCL) is
available in red.
The battery charger used in each unit can energize
batteries of up to 1 8AH. Though, when battery sets
greater than 7AH are required, the battery set must
be housed in a System 3 enclosure or a separate
®UL Listed battery enclosure.
System 3 enclosures may also be used to house
multiple Model PAD-4 units in a single enclosure, via
the Model S3AP Adapter Plate. Two (2) units are
capable of sharing the same battery set when
mounted in the same enclosure. Model S3AP can
also be used to mount the PAD-4 main board and
170-Watt power supply (Model FP2011-U1) into a
PAD-3 enclosure.
Each Model PAD-4 unit complies with seismic
certification, pursuant to the following:
ASCE Standard 7, 2005 Edition
International Building Code, 2006 Edition
California Building Code, 2007 Edition
ICC-ES AC 156, effective 2007
OSHPD preapproved, under: OSP-0057-1 0
- OSHPD CAN 2-1708A.5, Rev. 3
Each Model PAD-4-series unit also complies with
seismic certification, pursuant to ASC I SET 7-05,
Section 13.2.2, when used with the PAD-4 battery
bracket (Model PAD4-BATT-BRKT).
Configuration Options
Option Input[s] Output Controls Circuit Types
1 Input 1 All outputs 'Class B' circuits
Input 1 All outputs Class B' circuits 2 Input 2* Silences horns on Output 1 -
Input 1 Outputs 1 and 2 Class B' circuits
3
Input 2 Outputs 3 and 4 'Class B' circuits
Input 1 Output 1 'Class B' circuits
4
Input 2 Outputs 2, 3 and 4 Class B' circuits
5 Input 1 Outputs 1 through 4 'Class A'
circuit pairs
Input 1 Outputs 1 through 4 'Class A'
6 circuit pairs
Input 2* Silences horns on Output 1
Input 1 Outputs 1 and 2 'Class A'
circuit pairs
7
Input 2 Outputs 3 and 4 'Class A'
circuit pairs
* denotes when used with Siemens Model 'AS','NS'or 7W-series
horn /strobe devices
Indicator Lights
AC Power ON:
AUX iPS: Yellow
Ground Fault: Yellow
Output 1 Trouble: Yellow
Output 2 Trouble: T Yellow
Output 3 Trouble: Yellow
Output 4 Trouble: Yellow
I Test Mode: II Yellow I
Technical Data
AC Fail Trouble Contact Rating: 2.OA @ 30VDC, max.
'Form A'- Normally Closed (NC) I [resistive]
Basic Trouble Contact Rating: 2.OA @ 30VDC, max.
'Form C) [resistive]
3.OA per circuit, max.
Alarm Current: 6A, max. (via Model FP2011-U1} for NAcs and auxiliary power)
9A, max. (via Model FP2012-1.11}
Ambient 32° - 1200 F
Temperature: (00_ 49° C)
Relative Humidity: Up to 93% @860 F(30° C);
non-condensing
Auxiliary Power Circuit: One (1) circuit @ 3A max.
Battery Charging Capacity: 1 8AH
Input Circuits , Two (2) 'Class B' supervised
Configurations: or
Two (2) 'Class A' supervised
Input Current: 7.0mA, max.
Input Voltage Range: 16-33VDC/VFW
Installation Environment: Indoor, dry
Supervised, power-limited
0 1.0mA standby
current, max.-
NACs: Four (4) circuits
02K ohms (+), 8K ohms (-)
24VDC @ 6 Amps
Total Output Power: (with Model FF2011-U1)
24VDC @ 9 Amps
(with Model FP2012-U1)
0 Two (2)'Class A';
- Up to four (4) 'Class A'
Output Circuits I sA
Configurations: 0 -----
0 One (1)Class A,
Two (2) Class B;
Single-Unit Dimensions:
{W -x-H -x- D) 13.5 -x- 18.75 -x- 3.25
Model_PAD-4-ENCL cm. -x- 47.6 cm. -x- 8.3 cm.) .....................................................(34.3
Red
Model_PAD-4-ENCL
SIEMENS Industry, Inc.
Building Technologies Division
Temperature and Humidity Range
Each PAD-4 Distributed Power Supply Unit is ®UL 864
gth Edition Listed for indoor dry locations within a
temperature range of 1 2OI-3°F (49I-2°C) to
32I-3°F (0I-2°C) and a relative humidity of 93I-2%
at a temperature of 9O/-3°F (32/-2°C).
Details for Ordering
Model Part
Number Description
PAD-4-ENCL 500-050081 PAD-unit enclosure
PAD-4-MB 500-650217 PAD-unit main board
FP2011-LJ1 500-450222 L 170 Watt power supply
FP2012-Ui S54400-Z60-A1 300-Watt power supply
—System Kits —
Model Part Description
Number
Complete 6A PAD-4 kit with:
PAD4-6A 554339-Al -Al - One (1) Unit Enclosure, PAD-4-ENCL
- One (1) Main Board, PAD-4-MB
- One (1)170W power supply, FF201 1-U1
Complete 6A PAD-4 kit with:
- One (1) Unit Enclosure, PAD-4 ENCL
PAD46A-CLSA 554339-A2-A1 - One (1) Main Board, PAD-4-MB
- One (1)170W power supply, FP2011-U1
- One (1) 'Class A' Adapter card, PAD-4-CLSA
Complete 9A PAD-4 kit with:
PAD4-9A 554339-A3-A1 - One (1) Unit Enclosure, PAD-4-ENCL
- One (1) Main Board, PAD-4-MO
- One (1) 300W power supply, FP2012-Ui
Complete 9A PAD-4 kit with:
- One (1) Unit Enclosure, PAD-4-ENCL
PAD4-9A-CLSA S54339-A4-A1 - One (1) Main Board, PAD-4-MB
- One (1)300W power supply, FF2012-Ui
- One (1) 'Class A' Adapter Card, PAD-4-CLSA
-Optional Accessories
Model Part
Number
Description
PAD4-BATT-BRKT 554430-B4-A1 Battery bracket for NAC expander
PAD-4-LUA S54389-Cl-Al PAD-4 Laptop-Upload Adapter
PAD-4-CLSA 500-850254 'Class A' Adapter Card
S3AP 500-650257 PAD-4 NAC expander adapter plate
(for use with PAD-3 and System 3 enclosures)
Note: For the data sheet of the PAD-4 NAC Extender sold
in Canada, please see document, 3363C.
Notice: This marketing data sheet is not intended to be used for system design or installation purposes.
For the most up-to-date information, refer to each product's installation instructions.
Fire Safety
8 Fernwood Road
SIEMENS Industry, Inc. Florham Park, Ni 07932 June 2017
Building Technologies Division Tel: (973) 5932600 (SIIFS) Supersedes sheet dated 11/2015
FAX: (908) 547-6877 Printed in U.S.A. (Rev. 6)
URL: www.usaSiemens.comjFire
ZH
Series
F1E
Series (for mounting)
SIEMENS Data Sheet
Fire Safety Products
Notification Appliances_________
ZH & ZR - Strobes, Horns, & Horn I Strobes I Application: Indoor
Product Overview
- Strobes can be synchronized using the Siemens DSC sync modules, the Siemens 50-point,
252-point and 504-point addressable fire alarm control panels (FACPs), as well as with:
FireFinder® XLS and MXL® FACPs
PAD-3 or PAD-4 TM NAC Extenders with built-in sync protocol
- Selectable Continuous Horn or Temporal (Code-3) Tones with 90 or 95 dBA
selectable setting (Series 'ZH')
- Ceiling-mount models feature field-selectable Candela settings of 1 5/30/75/95cd and 11 5/1 77cd
- Wall-mount models feature field-selectable Candela settings of 15/30/75111 Occl and 135/1 85cd
- Base plate is protected by a disposable cover, and the appliances can quickly snap onto the base
after the walls are painted
- Strobes produce one (1) flash per second
- "Special Applications" listed with Siemens panels
- EZ Mount Universal Mounting Plate (Model ZB Series) —uses single plate
for ceiling and wall mount installations
- EZ Mount design —with separate base plate —provides ability to pre-wire the base
and test the circuit wiring before the walls are covered
- ®UL Listed & OULC Listed, FM (#3028994) Approved;
CSFM Approved (Series 'ZH': #71250067:0248 —> Fire Alarm Devices For The Hearing Impaired)
CSFM Approved (Series 'ZR': #71250067:0252 —> Fire Alarm Devices For The Hearing Impaired)
- ADA / NEPA compliant
Specifications
. General
- Audible/Visual notification appliances are listed for indoor use only
- Appliances are listed under ®UL Standard 1971 (Standard for Safety Signaling Devices
for Hearing Impaired) and ®UL Standard 464 (Fire Protective Signaling)
- Appliances use a universal back plate, which allows mounting to a
single-gang, double-gang, 4-inch-square (10.2 cm.), 4"-octal (10.2 cm.), or a 3-1/2" (8.9 cm.) octal backbox
- Two-wire configurations allows capability for directly connecting appliances to the mounting back plate
- Continuity check will occur for entire NAC circuit prior to attaching any audible / visual-notification appliances
- A cover fits over the mounting plate for protection to dust and other outside elements
Cover is easily removed when the appliance is installed over the back plate
- Removal of an appliance will result in a Trouble condition by the Siemens Fire Alarm Control Panel (FACP)
'Z' Series Notification Appliances 2584
SIEMENS Industry, Inc.
Building Technologies Division
Specifications - (continued)
Strobes and Audible Strobe Combinations
- Strobe appliances produce a minimum flash rate of 60 flashes per minute
(one [1] flash per second) over the Regulated Input Voltage Range, and
incorporate a Xenon flashtube enclosed in a rugged Lexan® lens
- Strobes are available with two (2) or four (4) field-selectable settings
in one (1) unit, and are rated - per ®UL 1971 - for up to:
15/30175/ll0cd for wall mounted
135/185cd for wall mounted
1 5/30/75/95cd for ceiling mounted
115/1 77cd for ceiling mounted
- Strobes operate over an extended temperature range of 32°F to 1207
(0°C to 49°C), and be listed for maximum humidity of 95% RH
- Strobe inputs are polarized for compatibility with standard reverse-polarity
supervision of circuit wiring by a Siemens FACP
Audible and Audible I Strobe Combinations
- Horns and horn I strobes are listed for Indoor use under ®UL Standard 464
- Horns are able to produce continuous synchronized output or a
Temporal Code-3 synchronized output
- Horns have at least two (2) sound-level settings of 90 and 95 dBA
Synchronization Modules
- The strobe portion, when synchronization is required, is compatible with the
Siemens DSC sync modules; the Siemens 50-point, 252-point and 504-point
addressable FACPs, as well as with:
FireFinder® XLS and MXL® FACPs
PAD-3 or PAD4TM NAC Extenders with built-in sync protocol
- The strobes will not drift out of synchronization at any time during operation
- Audibles and strobes are able to synchronize on a two-wire circuit with the capability
to silence the audible, if required
- Strobes revert to a non-synchronized flash-rate, if the sync module or
power supply should fail to operate (i.e. - contacts remain closed)
- All notification appliances are listed for Special Applications:
Strobes are designed to flash at 1-flash-per-second
minimum over their ''Regulated Input Voltage Range"
> Note: NFPA-72 specifies a flash rate of 1-to-2 flashes per second,
and ADA Guidelines specify a flash rate of 1-to-3 flashes per second
All candela ratings represent minimum-effective Strobe intensity, based on ®UL Standard 1971
Series ZH Strobe products are listed under ®UL Standards 1971 and 464 for indoor use
with a temperature range of 32°F to 120°F (0°C to 49°C) and maximum humidity of 93% ( 2%)
Series ZH horns are listed under ®UL Standard 464 for audible signal appliances (Indoor use only)
Mounting Diagram
SIEMENS Industry, Inc. - (Shown In Inches)
Building Technologies Division
Mounting Diagram
e
SECURING
SM SCREWS
OPENmO I'M FtAT SCREWI*000.-J Installation
I.) With the provided pan head screws, install mounting
plate to a:
- aingle-gang;
- double-gang;
- 4 (10.2 cm.) square;
- V (10.2 cm.) octagon backbox
Connect the field wiling.
Address wires back into backbox.
Place dust cover over mounting plate to protect the
terminals while performing the wiring-continuity check.
Remove dust cover before snapping or
installing the appliance onto the mounting plate
Technical Data
Removal
ImportanI: Device only has one (1) mounting
orientation. Match the top of the base to the
top of the device.
If it is desired to further secure the device to the
base, then use the two (2) optional screws which
are provided in the shipment To Install, punch
out the screw holes located at the top and
bottom of the device.
To remove the appliance, push a small, flat-bladed
screwdriver into the side opening. The screwdriver
must dear the snap release opening by 1/4 "(0.64cm.),
in order for the appliance's snap to disengage.
inipeitan(: Do not pry off the housing with a screw driver.
ZH Horn: Wall and Ceiling Mount
Operating Voltage (Special Application)
Per®UL 464
Input Voltage Low* High*
DC 1 16.0-33.OVDC 0.018 0.044
FWR 1 16.0 - 33.OVRMS 0.045 0.075
* Current draw is the same for the Continuous Horn, Code 3
Horn, and March Time settings
ZH Horn I Strobe Series: Wall Mount ZH Horn I Strobe Series: Ceiling Mount
Current Ratings (AMPs)
MAXIMUM RMS Current- with High dBA Setting
Input Voltage 15cd 3 c 75cd llOcd 135cd 185cd
DC I 16.0-33.OVDC 0.078 0.113 10.195 0.259 0.371 0.506
FWR 16.0-33.OVRMS 0.141 0.200 0.302 0.406 0.521 0.722
Current Ratings (AMPs)
MAXIMUM RMS Current- with Low dBA Setting
Input Voltage l5cd 30cd 75cd 95cd 135cd 185cd
DC 116.0-33.OVDC 10.070 10.107 10.18810.246101.324 0.455
FWR 16.0-33.OVRMS 0.123 0.179 0.290 0.391 0.497 0.699
ZR Strobe Series: Wall Mount
Current Ratings (AMPs)
Strobe Setting - (cd)
Input Voltage 15cd I 30cd I 75cd 110cd 135cd I 185cd
DC 16.0-33.OVDC 10.06410.098 10.17510.23310.318 0.445
FWR 16.0-33.0VRMS 10.10810.164 10.26810.36810.48210.684
ZR Strobe Series: Ceiling Mount
Current Ratings (AMPs)
Strobe Setting - (cd)
Input Voltage 15cd I 30cd I 75cd I 95cd 1 11 5c I 177cd
DC 116.0-33.0V1)C I 0.069 10.11110.20010.26410.318 10.445
FWR 116.0-33.OVRMSI 0.117 10.180 10.29710.39810.482 10.684
@ULC Directional Characteristics
-3 dBA 35 degrees left; 40 degrees right
-6 dBA 55 degrees left; 65 degrees right
SIEMENS Industry, Inc.
Building Technologies Division
Current Ratings (AMPs)
MAXIMUM RMS Current- with tLigh dBA Setting
Input Voltage 15cd 30cd 75cd 95cd ll5cd 177cd
DC 16.0-33.OVDC 0.087 0.131 0.222 0.292 0.371 0.506
FWR 16.0-33.OVRMS 0.149 0.216 0.331 0.436 0.521 0.722
Current Ratings (AMPs)
MAXIMUM RMS Current- with Low dBA Setting
Input Voltage 15cd 30cd 75cd 95cd I ll5cd 177cd
DC 16.0-33.OVDC 0.075 0.121 0.213 0.277 0.324 0.455
FWR 116.0-33.OVRMS 0.131 0.195 10.31910.42110.497 0.699
ZH and ZH-MC Series: Wall and Ceiling Mount
dBA Sound Output
Description Volume Reverberant Per ®UL 464
16.0 VDC 24.0 VDC 33.0 VDC
Continuous
Horn
Low 77 81 83
High 83 87 90
Code 3 Horn
(or March Time)* I Low 72 76 79
High 79 1 82 1 86
dBA Sound Output
Description Volume Reverberant Per ULC-S525-99
20.0 VDC 24.0 VDC 31.0 VDC
Continuous
Horn
Low 88 90 91
High 93 95 96
Code 3 Horn
(or March Time)*11
Low 88 90 91
High 93 95 96
** Available only in sync mode.
Technical Data - (continued)
Notes: 1. Strobes will produce 1 flash per second over the Input Voltage range.
These horn/strobe models are ®UL Listed to operate over a Voltage Range Limit from 1 6.OVDC to 33.OVDC
for 24VDC applications using filtered DC or unfiltered Full-Wave-Rectified (FWR) input voltage.
All models are ®UL Listed for indoor ceiling use with a temperature range of +0°C to +49°C
(+32°F to +1200F) and maximum humidity of 93% +1- 2% RH.
The effect of shipping and storage temperatures will not adversely affect the performance of the appliance
when stored in original cartons, and is not subjected to either misuse or improper handling of shipment.
Details for Ordering - (Including Mounting Options & Agency Approvals)
Agency Approvals
Model Part Number Description Mounting UL Options*
ULC FM CSFM
ZH-R 500-636159 Z Horn: Red B,D,E,F,X V V V V
ZH-W 500-636160 Z Horn: White B,D,E,F,X V V V V
ZH-MC-R 500-636161 Z Horn: Multi Candela (Wall), Red B,D,E,F,X V V V V
ZH-MC-W 500-636162 Z Horn: Multi Candela (Wall), White B,D,E,F,X V V V V
ZH-HMC-R 500-636163 Z Horn: Hi Multi Candela (Wall), Red B,D,E,F,X V V V V
ZH-HMC-W 500-636164 Z Horn: Hi Multi Candela (Wall), White B,D,E,F,X V V V V
ZH-MC-CR 500-636165 Z Horn: Multi Candela (Ceiling), Red B,D,E,F,X V V V V
ZH-MC-CW 500-636166 Z Horn: Multi Candela (Ceiling), White B,D,E,F,X V V V V
ZH-HMC-CR 500-636167 Z Horn: Hi Multi Candela (Ceiling), Red B,D,E,F,X V V V V
ZH-HMC-CW 500-636168 Z Horn: Hi Multi Candela (Ceiling), White B,D,E,F,X V V V V
ZR-MC-R 500-636169 Z Strobe: Multi Candela (Wall), Red B,D,E,F,X V V V V
ZR-MC-W 500-636170 Z Strobe: Multi Candela (Wall), White B,D,E,F,X V V V V
ZR-HMC-R 500-636171 Z Strobe: Hi Multi-Candela (Wall), Red B,D,E,F,X V V V V
ZR-HMC-W 500-636172 Z Strobe: Hi Multi-Candela (Wall), White B,D,E,F,X V V V V
ZR-MC-CR 500-636173 Z Strobe: Multi Candela (Ceiling), Red B,D,E,F,X V V V V
ZR-MC-CW 500-636174 Z Strobe: Multi Candela (Ceiling), White B,D,E,F,X V V V V
ZR-HMC-CR 500-636175 Z Strobe: Hi Multi Candela (Ceiling), Red B,D,E,F,X V V V V
ZR-HMC-CW 500-636176 Z Strobe: Hi Multi Candela (Ceiling), White B,D,E,F,X V V V V
ZB-R 500-636193 Accessory -(Includes base, dust cover,
mounting screws and installation sheet)
V V V V
ZB-W 500-636194 Accessory - (Includes base, dust cover,
i mounting screws and installation sheet) V V V V
V = Listed I Approved
* = Refer to data sheet #: 2585
for detailed mounting options
Notice: This marketing data sheet is not intended to be used for system design or installation purposes.
For the most up-to-date information, refer to each product's installation instructions.
Fire Safety Fire Safety
8 Fernwood Road 1577 North Service Road
SIEMENS Industry, Inc. Florham Park, Ni 07932 East Oakville, Ontario August 2016
Building Technologies Division Tel: (973) 593-2600 sii L6H 01-16 I Canada Supersedes sheet dated 6/2015
FAX: (908) 547-6877 Printed in U.S.A. Tel: [905] 465-8000 )Rev. 5)
URL: www.usa.Siemens.comlFire URL: www.siemens.cA
CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION
OFFICE OF THE STATE FIRE MARSHAL
FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM
LISTING SERVICE
LISTING No. 7125-0067:0248 Page 1 of I
CATEGORY: 7125 -- FIRE ALARM DEVICES FOR THE HEARING IMPAIRED
LISTEE: Siemens Industry, Inc. Building Technologies Division8 Fernwood Road, Florham Park, NJ
07932
Contact: James Muha (973) 593-2664 Fax (973) 593-6652
Email: james.muha@siemens.com
DESIGN: Models NH-R, NH-W, NH-CR, NH-CW, ZH-R, and ZH-W horns and models NS-MC-R,
NS-MC-W, ZH-MC-R, ZH-MC-W, ZH-HMC-R, AND ZH-HMC-W Horns / Strobes. Models
NS-MC-CR, NS-MC-CW, NS-HMC-CR, NS-HMC-CW, ZH-MC-CR, ZH-MC-CW, ZH-HMC-CR,
ZH-HMC-CW are horn / strobes for ceiling mount only. Suffix CR or CW are for ceiling and
color. Units are synchronized or non-synchronized strobes. Refer to Listee's data sheet for
additional detailed product description and operational
RATING: Electrical 16-33VDC/FWR
Candela: NS-MC-C, ZH-MC-C = 15/30/75/95 candela
NS-HMC-C, ZH-HMC-C = 115 / 177 cd
NS-MC, ZH-MC = 15/30/75/110 cd
ZH-HMC, = 135 / 185 cd
Flash Rate: 60 flashes / minute
INSTALLATION: In accordance with Listee's printed installation instructions, applicable codes &
ordinances and in a manner acceptable to the authority having jurisdiction.
MARKING: Listee's name, model number, electrical I candela rating and UL label.
APPROVAL: Listed as audible and audible II visual signaling devices for use with separately listed
electrically compatible fire control units. Models with strobe lights are suitable for the hearing
impaired. For indoor use only. All synchronization strobes shall be used with model DSC
sync control module (CSFM listing No. 7300-0067:212). Refer to manufacturer's installation
manual for details
Note: These appliances can produce a distinctive three-pulse Temporal Pattern Fire Alarm
Evacuation Signal (for total evacuation ) in accordance with NFPA 72, 2002 Edition.
NOTE:
09-07-2007
This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed
the test results and/or other data but does not make an independent verification of any claims. This listing is not
an endorsement or recommendation of the item listed. This listing should not be used to verify correct
operational requirements or installation criteria. Refer to Iistee's data sheet, installation instructions and/or other
Date Issued: July 01, 2020 Listing Expires June 30, 2021
Authorized By: DAVID CASTILLO,, ME., F.P.E.
Fire Engineering Division
CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION
OFFICE OF THE STATE FIRE MARSHAL
FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM
LISTING SERVICE
LISTING No. 7125-0067:0252 Page 1 of I
CATEGORY: 7125 -- FIRE ALARM DEVICES FOR THE HEARING IMPAIRED
LISTEE: Siemens Industry, Inc. Building Technologies Division8 Fernwood Road, Florham Park, NJ
07932
Contact: James Muha (973) 593-2664 Fax (973) 593-6652
Email: james.muha@siemens.com
DESIGN: Models ST-MC-RETRO-R, ZR-MC-W, ZR-MC-R, ZR-HMC-R, ZR-HMC-W intended for indoor
use on walls.
Models ST-MC-CW, ST-HMC-CW, ZR-MC-CR, ZR-MC-CW, ZR-HMC-CR, and ZR-HMC-CW
multi candela intended for indoor use mounted on the ceiling only.
Z -series strobes are intended for use with models ZB-R or ZB-W back boxes. ST - series
strobes are intended for use with models SHBBS surface back boxes. Model numbers may
be followed by alpha characters indicating lens orientation, lettering, and color. Refer to
listee's data sheet for additional detailed product description and operating considerations.
RATING: Electrical 16-33VDC/FWR
Candela: ST-MC-RETRO-R 15cd, 30cd, 75cd, 110cd
ZR-MC-W, ZR-MC-R 15cd, 30cd, 75cd, 110cd
ZR-MC-CR, ZR-MC-CW 15cd, 30cd, 75cd, 95cd
ST-MC-CW 15cd, 30cd, 75cd, 95cd
ZR-HMC-R, ZR-HMC-W 135/185cd
zR-HMC-CR, ZR-HMC-CW 115/177cd
Flash Rate: 60 flashes / minute
INSTALLATION: In accordance with Listee's printed installation instructions, applicable codes &
ordinances and in a manner acceptable to the authority having jurisdiction. Models with suffix
-w are wall mount only. Models with suffix -C are ceiling mount only. All models are for
indoor use only.
MARKING: Listee's name, model number, electrical / candela rating and UL label.
APPROVAL: Listed as strobe light suitable for the hearing impaired when used with separately listed
electrically compatible fire alarm control units. Refer to listee's installation instruction manual
for details.
NOTE:
9-10-2007mt
This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed
the test results and/or other data but does not make an independent verification of any claims. This listing is not
an endorsement or recommendation of the item listed. This listing should not be used to verify correct
operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other
Date Issued: July 01, 2020 Listing Expires June 30, 2021
Authorized By: DAVID CASTILLO,, M.E., F.P.E.
Fire Engineering Division
CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION
OFFICE OF THE STATE FIRE MARSHAL
FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM
LISTING SERVICE
LISTING No. 7315-0067:0268 Page 1 of 1
CATEGORY: 7315-- POWER UNITS
LISTEE: Siemens Industry, Inc. Building Technologies Division8 Fernwood Road, Florham Park, NJ
07932
Contact: James Muha (973) 593-2664 Fax (973) 593-6652
Email: james.muha@siemens.com
DESIGN: Model PAD-4 distributed power module NAC expander monitors the voltage of its two input
circuits to determine when to operate its four notification circuits. It provides one AC Fail and
one Trouble Relay as well as an auxiliary power circuit. It can also provide up to 9 amps of
24 VOC power and adds two additional Class A circuits by adding the optional PAD-4-CLSA
module. The PAD-4 consists of the following:
PAD-4-MB; PAD-4 Main Board
PAD4-CLSA; Class A Expander Module
FP-2011-UI; 170W Power Supply
FP-2012-UI; 300W Power Supply
Refer to listee's installation/operation manual for additional detailed product description and
operational considerations.
RATING: 120/240 VAC, 60/50 HZ, 24 VDC
INSTALLATION: In accordance with listee's printed installation instructions, applicable codes & ordinances
and in a manner acceptable to the authority having jurisdiction. Unit shall be fully supervised
and shall have 24 hr. battery back-up.
MARKING: Listees name, model number, electrical rating, and UL label.
APPROVAL: Listed as a notification circuit expander for use with listee's separately listed compatible fire
alarm control units. Refer to listee's Installation Instruction Manual for details
08-20-13 gt
This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed
the test results and/or other data but does not make an independent verification of any claims. This listing is not
an endorsement or recommendation of the item listed. This listing should not be used to verify correct
operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other
Date Issued: July 01, 2020 Listing Expires June 30, 2021
Authorized By: DAVID CASTILLO,, ME., F.P.E.
Fire Engineering Division