The URL can be used to link to this page

Home My WebLink About5760 FLEET ST; 210; FPC2020-0061; PermitPERMIT REPORT C 4L-City of arlsbad Print Date: 03/22/2022 Permit No: FPC2020-0061 Job Address: 5760 FLEET ST, # 210, CARLSBAD, CA 92008-4713 Status: Closed - Finaled Permit Type: FIRE-Construction Commercial Work Class: Fire Sprinklers Parcel #: 2111000200 Track #: Applied: 04/06/2020 Valuation: $283,664.49 Lot #: Issued: 04/20/2020 Occupancy Group: Project #: Finaled Close Out: 06/17/2020 #of Dwelling Units: Plan #: Bedrooms: Construction Type: Bathrooms: Orig. Plan Check #: Inspector: Plan Check#: Final Inspection: Project Title: Description: THE QUAD -SPRINKLER TI (9 HEADS) Applicant: FPContractor: TITAN FIRE PROTECTION INC TITAN FIRE PROTECTION INC EDUARDO MARTINEZ 1341 DISTRIBUTION WAY, # STE 14 1341 DISTRIBUTION WAY, # STE 14 VISTA, CA 92081-8843 VISTA, CA 92081-8843 (760) 295-3436 (760) 295-3436 FEE AMOUNT FIRE NFPA 13 or 13R System 7 - 100 heads $553.00 Total Fees: $553.00 Total Payments To Date: $553.00 Balance Due: $0.00 Fire Department Page 1 of 1 1635 Faraday Avenue, Carlsbad CA 92008-7314 1 760-602-4665 1 760-602-8561 f I www.carlsbadca.gov A (11 TAN FIRE PROTECTION ffc2-o-o - Fire Protection Contractor License #989280 MATERIAL SUBMITTAL: PRODUCT DATA AND MANUFACTURER'S INSTRUCTIONS THE QUAD, SUITE 210 5760 FLEET STREET, SUITE 210 CARLSBAD, CA 92008 ES-A-30008$ Job Name Contractor Job Location Approval Engineer Contractor's P.O. No, Approval Representative Series 3000S0'"' EXISTING Double Check Detector Sizes: 21/2 ' -12" Series 300056 Double Check Detector Assemblies are designed for use in accordance with water utility nonhealth hazard con- tainment requirements. It is mandatory to prevent the reverse flow of fire protection system substances, Le,, glycerin wetting agents, stagnant water and water of non-potable quality from being pumped or siphoned into the potable water supply. Features 30005$ Cam-Check Assembly valve provides low head loss Short lay length is ideally suited for retrofit installations Stainless Steel body is half the weight of competitive designs reducing installation and shipping cost Stainless steel construction provides long term corrosion protection and maximum strength Single top access cover with two-bolt grooved style coupling for ease of maintenance No special tools required for servicing 'Compact construction allows for smaller vaults and enclosures 'Furnished with /8 x 3/4' bronze meter (gpm or cfm) Detects underground leaks and unauthorized water use May be installed horizontal or vertical low up" position (ASSE Only) Available Models Suffix: LG - less shutoff valves OSY - UL/FM outside stem and yoke resilient seated gate valves OSY FxG - flanged inlet gate connection and grooved outlet gate connection OSY GxF - grooved inlet gate connection and flanged outlet gate connection OSY GxG - grooved inlet gate connection and grooved outlet gate connection CFM - cubic feet per minute GPM - gallons per minute meter Post indicator plate and operating nut available - consult factory It is illegal to use this product in any plumbing system providing water for human consumption, such as drinking or dishwashing, in the United States Before installing standard material product consult your local water authority, building and plumbing codes. Specifications A Double Check Detector Assembly shall be installed on fire protection systems when connected to a drinking water supply. Degree of hazard present is determined by the local authority having jurisdiction. The main valve body shall be manufactured from 300 Series stainless steel to provide corrosion resistance, 100% lead free through the waterway, The double check detector assembly consists of two independently operating, spring loaded check valves, two UL, FM, OSY resilient seated gate valves, and bypass assembly. The bypass assembly con- sists of a meter (cubic ft. or gallons), a double check including shutoff valves and required test cocks. Each cam-check shall be internally loaded and provide a positive drip tight closure against reverse flow, Cam-check includes a stainless steel cam arm and spring, rubber faced disc and a replaceable seat. There shall be no brass or bronze parts used within the cam- check valve assembly. The check valve seats shall be of molded thermoplastic construction. The use of seat screws as a reten- tion method is prohibited. All internal parts shall be accessible through a single cover on the valve assembly. The valve cover shall be held in place through the use of a single grooved style two-bolt coupling. The bypass line shall be hydraulically sized to accurately measure low flow. The bypass line shall consist of a meter, a small diameter double check assembly with test cocks and isolation valves. The bypass line double check valve shall have two independently operating modular poppet check valves, and top mounted test cocks. The assembly shall be an Ames Fire & Waterworks 3000SS. Materials All internal metal parts: 300 Series stainless steel, Main valve body: 300 Series stainless steel, Check assembly: Noryl Flange dimension in accordance with AWINA Class D. Noryl® is a registered trademark of General Electric Company. The wetted surface of this product contacted by consumable water contains less than 0.25% of lead by weight. Ames Fire &Waterworits proriUtt speciftcaWsin lJ$ customary units and meft are appradmats and are provided for reference only, For precise mean- mM please contact Ames Fire &Wa Works Technical Service, Ames Fire &Waterworks reserves his dgft tsclrançjs or modify product design, construction, speciticatrons or materials wihiout prior notice and wttiout incurring any obigatron to make erich changes and morilficatronoan Ames Fire &Waterworks products previously or subsequenily sold, ¶uT-I"ji'i5;i A WATI'S Brand I L A FIRE &WATERWORKS Pressure - Temperature Temperature Range: 33°F - 110°F (0.5°C - 43°C) Maximum Working Pressure: 175p5i (12 bar) Capacity Flow curves as tested by Underwriters Laboratory per UL 1469, 1996, * Rated flow **UL Tested mmmmmommo ommmm ._. . III l mmw!rmdmmm • _•_____. .__ .____ - I-. i.i•••u••uu u•••• siu•ua•uu i.uU UU ••••• Standards ASSE 1048, AWWA C510-92, CSA B64,5, UL 1469 Approvals UL Olassflect (OY only), FM (sizes 21/2' - 10", OSY only) 65GB 43 4,WP/ o-® ow 6" * ** 62 9 41 6 21 3 0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 ope 300 700 1140 1520 1000 2280 2660 3040 3470 3000 4180 4560 4940 5320 5706 1pm 5 10 15 tps ¶5 3 46 Mpg Ppoi 83 12 62 9 41 0 --- -- 21 3 - - -- - - - - - 0 2000 2250 2506 gpm 750 500 750 1000 1250 1500 1750 950 1900 2650 3800 4750 5700 6650 7600 8550 9500 1pm 5 10 15 ; 1.5 3 46 mp IV lit,, kPp P41 * ** 103 15 63 12 82 9 418 21 2 - - -- - - - - 0 250 500 750 1000 1250 1500 1750 2000 2250 2500 3000 3900 gpm 950 1900 2850 3000 4750 5700 8650 7600 8550 0500 11400 13300 1pm 5 10 1.5 3 12" kh PO 110 16 97 14 55 8 41 6 28 4 14 2 0 500 1000 1500 2000 2500 3000 3500 4000 4500 gpm 1900 3800 5700 7600 9500 11400 13300 15200 17100 1pm 5 10 10 1,5 3 MP SIZE DIMENSIONS NET WEIGHT NET WEIGHT ko. A In. non C (06) k non D ki mm 6 in. mao L in, aim P in, mm w/Gates lb. kg. w/o Gatos lb. kj 2'/z 965 1634 416 31/2 89 10 250 22 559 121/2 318 155 70 68 31 3 38 965 18½ 479 31/4 95 10 250 22 559 13 330 230 104 70 32 40 1016 22/4 578 41/, 114 10250 22 559 14½ 368 240 109 73 33 6 481/2 1232 30½ 765 51/z 140 1 15 381 271h 699 151/2 394 390 177 120 54 8 52½ 1334 W/4 959 61/4 171 15 381 291/2 749 18½ 464 572 259 180 82 0 55½ 1410 453/4 1162 8 200 15 381 29½ 749 191/2 495 774 351 190 86 12 57½ 1461 53½ 1349 91h 241 15 381 291/2 749 21 533 1044 474 220 100 A WATTS Brand USA: Backflow 1: (978) 689-6066 • F: (978) 975-8360 • AmesFireWater.com USA; Control Valves 1: (713) 943-0688 • F: (713) 944-9445 • AmesFireWater.cnm Canada; T: (906) 332-4096 • F: (906) 332-7068 • AmesFreWater,ca Latin America; 1: (52) 55-4122-0138 • AmesFireWator,com ES-a-3000SS 1947 0 2019 Ames Fire & Waterworks Page 1 of 7 MIRAGE® STANDARD AND QR CONCEALED PENDENT S4,J K] 4 l:II[1.,LTIy SPRINKLER VK462 AND HP SPRINKLER VK463 (K5.6) The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 2699459501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Visit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com DESCRIPTION Viking Mirage® Standard and Quick Response Concealed Pendent Sprinkler VK462 and HP Sprinkler VK463 are thermosensitive glass-bulb spray sprinklers designed for installation on concealed pipe systems where the appearance of a smooth collingi Is desired. The sprinkler is pre-assembled with a threaded adapter for installation with a low profile cover assembly that provides up to %" (12.7 mm) of vertical adjustment. The two-piece design allows installation and testing of the sprinkler prior to installation of the cover plate. The "push-on", "thread-off' design of the concealed cover plate assem- bly allows easy installation of the cover plate after the system has been tested and the ceiling finish has been applied. The cover assembly can be removed and reinstalled, allowing temporary removal of ceiling panels without taking the sprinkler system out of service or removing the sprinkler. The Electroless Nickel PTFE (ENT) coating has been investigated for installation in corrosive environments and is cULus Listed as indicated In the Approval Charts. The ENT finish is only available for the sprinkler assembly, the cover plate is not plated. LISTINGS AND APPROVALS tews cULus Listed: Category VNIV FM Approval: Class 2015 NYC Approved: MEA 89-92-E, Volume 32 ZtWARNING: Cancer and Reproductive Harm. www.P85Warnings.ca.gov [) VdS Approved: Certificate G4080021 LPCB Approved: Certificate number 096e/12 CE Certified: Standard EN 12259-1, EC-certificate of conformity 0786-CPD-40249 CCCF Approved: Approved by the China Certification Center for Fire Products (CCCF) £ MED Certified: Standard EN 12259-1, EC-certificate 0832-MED-1 003 Refer to Approval Chart 1 Design Criteria for cULus Listing requirements, and refer to Approval Chart 2 and Design Criteria on page for FM Approval requirements that must be followed. TECHNICAL DATA Specifications: Available since 2006. Minimum Operating Pressure: 7 psi (0.5 bar)* Maximum Working Pressure: Sprinkler VK463 is rated for use with water working pressures ranging from the minimum 7 psi (0.5 bar) up to 250 psi (17.2 bar) for high-pressure systems. High-pressure (HP) sprinklers can be identified by locating "250" stamped on the deflector. Sprinkler VK462 is rated to a maximum 175 psi (12 bar) wwp. Factory tested hydrostatically to 500 psi (34.5 bar) Thread size: 1/2" (15 mm) NPT Nominal K-Factor: 5.6 U.S. (80.6 metrict) Glass-bulb fluid temperature rated to -65°F (-55°C) Patents Pending *cuLus Listing, FM Approval, and NFPA 13 installs require a minimum of 7 psi (0.5 bar). The minimum operating pressure for LPCB and CE Approvals ONLY is 5 psi (0.35 bar). tMetnc K-factor measurement shown is when pressure is measured in Bar. When pressure is measured in kPa, divide the metric K-factor shown by 10.0. Material Standards: Sprinkler Body: Brass UNS-C84400 Deflector: Copper UNS-C19500 for Sprinkler VK462 Phosphor Bronze UNS-051000 for Sprinkler VK463 Deflector Pins: Stainless Steel Alloy Bulb: Glass, nominal 3 mm diameter Form No. F_103005 18.10.11 Rev 18.2.P65 Replaces Form No. F_103005 Rev 18.2 (Added P65 Warning.) Page 2 of 7 The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs©vikingcorp.com Visit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com Pip Cap and Insert Assembly: Copper LJNS-ClI000 and Stainless Steel UNS-S30400 Button: Brass UNS-C36000 Screws: 18-8 Stainless Steel Belleville Spring Sealing Assembly: Nickel Alloy, coated on both sides with Teflon Tape Yoke: Phosphor Bronze UNS-051000 Cover Adapter: Cold Rolled Steel UNS-G10080, Finish: Clear Chromate over Zinc Plating Cover Assembly Materials: Cover: Copper UNS-C11000 or Stainless Steel UNS-530400 Base: Brass UNS-C26000 or UNS-C26800 Springs: Nickel Alloy Solder: Eutectic Ordering Information: (Also refer to the current Viking price list.) Viking Mirage® Standard and Quick Response Concealed Pendent Sprinklers and Cover Plate Assemblies must be ordered separately: Sprinkler: Base Part No. VK462 - 13503A for Brass finish and 13503JN for ENT finish. VK463 - HP Base Part No. 13667A Specify sprinkler temperature rating by adding the appropriate suffix for the temperature rating to the base part number: Temperature Suffix: 155 OF (68 "C) = B, 175 OF (79 "C) = D, 200 OF (93 "C) = E For example, sprinkler VK463 with a 155 OF (68 "C) temperature rating = 13667AB. Standard Cover Plate Assembly: Base Part No. 13504 (2-3/4" diameter), Base Part No. 13642 (3-5/16" diameter), or Base Part No. 15394 (square cover plate, 3-5/16") Specify finish and temperature rating of the cover plate assembly by adding the appropriate suffixes for the finish and the cover temperature rating to the base part number: Finish Suffix: Polished Chrome = F, Brushed Chrome = F-/B, Bright Brass = B, Antique Brass = B-/A, Brushed Brass = B-/B, Brushed Copper = E-/B, Painted White = M-/W, Painted Ivory = M-/l, Painted Black = M-/B Temperature Suffix: 135 OF (57 "C) UL (139 OF (59 "C) FM and LPCB) = A, 165 OF (74 °C) = C For example, cover 13504 with a Polished Chrome finish and a 165 OF (74 "C) temperature rating = 13504FC. Stainless Steel Cover Plates (not availble with any finish or paint): Base Part No. 21876 (2-3/4" diameter) or Base Part No. 21875 (3-5/16" diameter). Temperature Suffix: 135 OF (57 "C) UL (139 OF (59 °C) FM and LPCB) = A, 165 OF (74 "C) = C For example, cover 21876 with a 165 OF (74 °C) temperature rating = 21876C NOTE: The cLJLus Listings for the square cover plate 15394 are for the 135 "F (57 "C) temperature rated cover plate only. Refer to the Approval Chart. Available Finishes And Temperature Ratings: Refer to Table 1. Accessories: (Also refer to the Viking website.) Sprinkler Wrenches**: Heavy Duty Wrench Part No. 14047W/B (available since 2006), or Head Cabinet Wrench Part No. 14031*** (available since 2006) Optional Concealed Cover Plate Installer Tool Part No. 14412 for cover 13504, or Part No. 14867 for the large diameter cover (available since 2007) **Requires a 1/2 ratchet (not available from Viking). ***Optional for removal of the protective cap. Ideal for sprinkler cabinets. Sprinkler Cabinet: Part No. 01731A (available since 1971) INSTALLATION Refer to appropriate NFPA Installation Standards. OPERATION During fire conditions, when the temperature around the sprinkler approaches its operating temperature, the cover plate detaches. Continued heating of the exposed sprinkler causes the heat-sensitive liquid in the glass bulb to expand and the bulb to shatter, releasing the yoke, pip-cap and sealing spring assembly. Water flowing through the sprinkler orifice strikes the sprinkler deflector, forming a uniform spray pattern to extinguish or control the fire. INSPECTIONS, TESTS AND MAINTENANCE Refer to NFPA 25 for Inspection, Testing and Maintenance requirements. AVAILABILITY Viking Sprinklers VK462 and VK463 are available through a network of domestic and international distributors. See The Viking Corporation web site for the closest distributor or contact The Viking Corporation. GUARANTEE For details of warranty, refer to Viking's current list price schedule or contact Viking directly. Form No. F_103005 18.10.11 Rev 18.2.P65 Page 30f7 MIRAGE® STANDARD AND QR CONCEALED PENDENT N I KING SPRINKLER VK462 AND HP SPRINKLER VK463 (K56) The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058 Telephone; 269.9459501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcsvikingcorp.com Visit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com TABLE : AVAILABLE SPRINKLER l RATINGS JAND1lIII:l*1 Sprinkler Sprinkler Maximum Cover Plate Large Cover Square Cover Temperature Nominal Ambient Temperature Rating of Cover Base Part Plate Base Part Plate Base Part Bulb Color Classification Temperature Ceiling Assembly (Required) Number'Number3 Number' Rating' Temperature2 135°F (57 °C) cULus Ordinary 155 °F (68° C) 100 °F(38°C) 135040r218765 13642 0r218755 15394 Red 139 °F_(59_°C)_FM arid_LPCB Intermediate 175 °F (79° C) 150 °F (65° C) 165 °F (74 °C) 13504 or 21876 13642 or 2187551 15394 1 Yellow Intermediate 200 °F (93° C) 150 °F (65° C) 165 °F (74 °C) 13504 or 21876 13642 or 2187511 15394 Green Cover Plate Finishes': Polished Chrome, Brushed Chrome, Bright Brass, Antique Brass, Brushed Brass, Brushed Copper, Painted White, Painted Ivory, or Painted Black Sprinkler Finishes: Brass and ENT Corrosion Resistant Coatings": ENT Footnotes The sprinkler temperature rating is stamped on the sprinkler deflector. 2 Based on NFPA-13. Other limits may apply, depending on fire loading, sprinkler location, and other requirements of the Authority Having Jurisdiction. Refer to specific installation standards. Part number shown is the base part number. For complete part number, refer to current Viking price list schedule. "The corrosion resistant coatings have passed the standard corrosion test required by the approving agencies indicated in the Approval Charts. These tests cannot and do not represent all possible corrosive environments. Prior to installation, verify through the end-user that the coatings are compat- ible with or suitable for the proposed environment. For automatic sprinklers, the ENT coating is applied to all exposed exterior surfaces, including the waterway, but the Belleville spring is exposed. Stainless Steel versions are not available with any finishes or paint. All custom color painted cover plates will have an identifying label affixed to the inside of the cover that indicates the custom color and will have a representative sample (a paint dot) of the paint on the label. Figure 1: Identification of Custom Paint for Concealed Covers - '--. . ....., Figure 2: Square Cover Assembly 15394 Form No. F103005 18.10.11 Rev 18.2.P65 Page 4 of 7 NIKING® MIRAGE® STANDARD AND A QR CONCEALED PENDENT SPRINKLER VK462 AND HP SPRINKLER VK463 (K5.6) The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Visit the Viking wobsite for the latest edition of this technical data page: www.vikinggroupinc.com A Sprinkler Temperature Rat,g p prova a 4, Cover Plate Temperature Rating Mirage® Concealed Pendent Sprinklers VK462 and VK463 AW14 Cover Plate Fnsh KEY -] Thread Nominal Maximum Listings and Approvals4 Sprinkler SIN Lize K-Factor Water Working (Refer also to Design Critarla) jlnch mm US met n& cULus' NYC VdS" LPCB I CE 1G [ ? Base Part No1 Pressure Standard Response Applications 13503A VK462 1/2' -- 5.6 806 175 psi (l2bar) -- -- AY1,CZ1 AY1,BZ1 AYI, CZ11 AY 19785A VK462 1/2" - 56 1 80 175 psi (l2bar) -- -- - -- AY2,cZ2 21356A VK462 -- 15 56 80.6 175 psi (12 bar) -- -- - -- - AY2,CZ2 Quick Response Applications 13503A VK462 1/2" 15 5.6 80.6 175 psi (12 bar) AV1, BX1,AV1,BX16 - - -- AY3 -- 13503JN11 VK462 1/2" 15 5.6 80.6 175 psi (12 bar) AV1, BX1,AV1, BX16 - - -- -- -- __________ AS3, BT3 13667A VK463 1/2" 15 5.6 1 80.6 250 psi (17.2 bar)' AV1, BX1 AV1, BX16 -- -- -- -- -- Cover Plate Assembly Temperature Ratings1'9 Sprinkler Temperature S - 135 OF (57 °C) cover 21876 or 21875 (large diameter) Cover Plate Assembly Finishes10 Ratings I - 165 OF (74 °C) cover 21876 or 21875 (large diameter) I - Polished Chrome, Brushed Chrome, Bright Brass, Antique A - 155 OF (68 °C) OF v - 135 (57 C) cULus Listed cover 13504, 13642 (large Brass, Brushed Brass, Brushed Copper, Painted White, diameter), r B - 175 OF (79 C) and 200 OF x - 165°F (74 °C) cover 13504, or 13642 (large diameter) Painted Ivory, or Painted Black (93 C) Y - 135 OF (57 °C) cover 13504 LPCB Approved as 139 OF 2 - Brass C - 200 OF (93 °C) (59 °C) 3 - Stainless Steel Z - 165 OF (74 °C) cover 13504 Footnotes Part number shown is the base part number. For complete part number, refer to current Viking price list schedule. 2 Metric K-factor measurement shown is when pressure is measured in Bar. When pressure is measured in kPa, divide the metric K-factor shown by 10.0. The Water Working Pressure rating is stamped on the deflector. This chart shows the listings and approvals available at the time of printing. Other approvals may be in process. Check with the manufacturer for any additional approvals. Listed by Underwriter's Laboratories for use in the U.S. and Canada. 6 Accepted for use, City of New York Department of Buildings, MEA Number 89-92-E, Vol. 32. VdS Approved, standards VdS 2344:2005-12, VdS 2100-25:2008-01, and EN 12259-1:1999 + A1:2001 + A2:2004 + A3:2006, Certificate G4080021. 6 CE Certified, Standard EN 12259-1, EC-certificate of conformity 0786-CPD-40249. The 1351139 OF cover has an orange label. The 165 OF (74 °C) cover has a white label. tO Painted finish consists of Polyester Baked Enamel. Other paint colors are available on request with the same listings as the standard paint colors. Listings and approvals apply for any paint manufacturer. Contact Viking for additional information. 11 cULus Listed as corrosion resistant. 12 IVIED Certified, Standard 12259-1, EC-certificate 0832-MED-1003. NOTE: Custom colors are indicated on a label inside the cover assembly. Refer to Figure 1. Form No. F_103005 18.10.11 Rev 18.2.P65 Page 5 of 7 NG ® MIRAGE® STANDARD AND i 111F'1 A l.I9I['qiuqiy QR CONCEALED PENDENT III SPRINKLER VK462AND HP SPRINKLER VK463 (K5.6) The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs©vikingcorp.com Visit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com DESIGN CRITERIA - UL (Also refer to Approval Chart 1) cULus Listing Requirements: Mirage® Concealed Pendent Sprinklers VK462 and VK463 are ctJLus Listed as quick response for installation in accordance with the latest edition of NFPA 13 for standard coverage pendent spray sprinklers as indicated below. For hazard occupancies up to and including Ordinary Hazard, Group II. Protection areas and maximum spacing shall be in accordance with the tables provided in NFPA 13. Maximum spacing allowed is 15 ft. (4.6 m). Minimum spacing allowed is 6 ft. (1.8 m) unless baffles are installed in accordance with NFPA 13. Minimum distance from walls is 4 in. (102 mm). Maximum distance from walls shall be no more than one-half of the allowable distance between sprinklers. The distance shall be measured perpendicular to the wall. The sprinkler obstruction rules contained in NFPA 13 for standard coverage pendent spray sprinklers must be followed. NOTE: Concealed sprinklers must be installed in neutral or negative pressure plenums only. VdS ADDroval Requirements: The sprinkler can be installed in a concrete ceiling (massive ceiling) or in a false ceiling made of light materials. This sprinkler is deflector fixed type and can be only activated by heat. The housing is not tight. C) Follow installation guidelines of current standards, CEA4001VdS and EN 12845. These sprinklers can only be installed in LH and OH occupan- cies, except in OH4. NOTES: Due to the design the sprinkler type Domed-CCP' shall not be installed in false ceilings in which the false ceiling space is protected by a water extinguishing system. Due to the design the sprinkler type 'Domed-CCP' shall not be installed in false ceilings in which during a fire the pressure above the false ceiling may be assumed to be higher than the pressure below the false ceiling. The criterion for the dropping of the cover relevant for this approval is heat. Steps of installation: Prepare the sprinkler key. Remove the plastic cover. Hold the sprinkler with the wrench and fasten it. Replace the plastic cover and do not remove until the cover is installed. IMPORTANT: Always refer to Bulletin Form No. F_091699 - Care and Handling of Sprinklers. Also refer to Form No. F080614 for general care, installation, and maintenance information. Viking sprinklers are to be installed in accordance with the latest edition of Viking technical data, the appropriate standards of NFPA, LPCB, APSAD, VdS or other similar organizations, and also with the provisions of governmental codes, ordinances, and standards, whenever applicable. Form No. F_103005 18.10.11 Rev 18.2.P65 F Fcl~_69_0 __ 00(7 ( Page 6 of 7 MIRAGE® STANDARD AND QR CONCEALED PENDENT cj K] 4 l:IIE1u'L'iv SPRINKLER VK462 AND HP SPRINKLER VK463 (K5.6) The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone; 269-945.9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs©vikingcorp.com Visit the Viking wobsite for the latest edition of this technical data page: www.vikinggroupinc.com Approval Chart 2 (FM) SprIerTerrperurietoi Cover Plate Temperatire Rv s Mirage Standard Response Concealed Pendent Sprinkler VK462 AW14 Cover Plate Fh KEY Sprinkler Base NPT Thread Size I Nominal K-Factor Maximum FM Approvals Part No.' I SIN i I I I Water Working I (Refer also to Design Criteria below.) Inch I mm I U.S. I metric2 I Pressure 13503A VK462 1/2" 15 5.6 80.6 175 psi (12 bar) Awl, BXI,AY2, BZ2 Cover Plate Assembly Temperature Ratings'- Cover Plate Assembly Finishes' Y - 139 °F (59 °C) cover 21875 or 21876 Sprinkler Temperature Ratings z - 165 °F (74 C) cover 21875 or 21876 1 - Polished Chrome, Brushed Chrome, Bright A - 155 oF (68 °C) W - 139 °F (59 °C) cover 13504, 13642 (large diameter), or Brass, Antique Brass, Brushed Brass, B - 175 °F (79 °C) and 200 °F (93 °C) 15394 (square cover plate) Brushed Copper, Painted White, Painted X - 165 F (74 C) cover 13504, 13642 (large diameter), or Ivory, or Painted Black 15394 (square cover plate) 2 - Stainless Steel Footnotes 1 Part number shown is the base part number. For complete part number, refer to current Viking price list schedule. 2 Metric K-factor measurement shown is when pressure is measured in Bar. When pressure is measured in kPa, divide the metric K-factor shown by 10.0. This chart shows the FM Approvals available at the time of printing. Other approvals may be in process. Check with the manufacturer for any additional approvals. The 139 °F (59 °C) cover has an orange label. The 165 °F (74 °C) cover has a white label. Painted finish consists of Polyester Baked Enamel. Other paint colors are available on request with the same listings as the standard paint colors. Listings and approvals apply for any paint manufacturer. Contact Viking for additional information. NOTE: Custom colors are indicated on a label inside the cover assembly. Refer to Figure 1. DESIGN CRITERIA -FM (Also refer to Approval Chart 2 above.) FM Aooroval Requirements: Viking Concealed Pendent Sprinkler VK462 is FM Approved as a standard response Non-Storage concealed pendent sprinkler as indicated in the FM Approval Guide. For specific application and installation requirements, reference the latest applicable FM Loss Prevention Data Sheets (including Data Sheet 2-0). FM Global Loss Prevention Data Sheets contain guidelines relating to, but not limited to: minimum water supply requirements, hydraulic design, ceiling slope and obstructions, minimum and maximum allowable spacing, and deflector distance below the ceiling. NOTE: The FM installation guidelines may differ from cULus and/or NFPA criteria. IMPORTANT: Always refer to Bulletin Form No. F_091699 - Care and Handling of Sprinklers. Also refer to Form No. F_080614 for general care, installation, and maintenance information. Viking sprinklers are to be installed in accordance with the latest edition of Viking technical data, the appropriate standards of NFPA, FM Global, LPCB, APSAD, VdS or other similar organiza- tions, and also with the provisions of governmental codes, ordinances, and standards, whenever applicable. Form No. F_103005 18.10.11 Rev 18.2.P65 Page 7 of 7 MIRAGE® STANDARD AND QR CONCEALED PENDENT 'ill 1(1 1 l:II[.q..i.,yM SPRINKLER VK462 AND HP SPRINKLER VK463 (K5.6) The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcsvikingcorp.com Visit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com Sprinkler and Adapter Assembly Protective cap Sprinkler Wrench removed - Part No. I4047WB** _-. Step 1: Carefully slide the wrench sideways around the deflector and pins 2-1/4" (57 mm) diameter opening required in the ceiling. Step 2: t Carefully press the wrench upward and turn slightly to ensure engagement with the sprinkler wrench flats. NEVER install the sprinkler by applying the installation Sprinkler wrench across the frame arms. DO NOT overtighten. wrench fla Use only the designated sprinkler wrenches, Viking Part Numbers 14047WB** or I4031**. A leak tight seal should be achieved by turning the sprinkler clockwise Ito 1-1/2 turns beyond finger tight. Figure 3: Sprinkler Installation and Proper Wrench Usage ** A 112" ratchet is required (Not available from Viking) Sprinkler frame arms 1/2" (15 mm) NPT 2-9/16" (65 mm) Maximum / 2-1/16" (52 mm) Minimum - Er _ E tn _ - 2-3/4" (70 mm) or NOTE: Upon sprinkler activation, the deflector descends 3-5/16" (84 mm) to approximately 13/16" (21 mm) below the sprinkler body. Figure 4: Sprinkler Dimensions and Cover Installation Form No. F103005 18.10.11 Rev 18.2.P65 Replaces Form No. F103005 Rev 18.2 (Added P65 Warning.) Page 1 of 6 \IIKING® 4 MICROFAST® QUICK l.4:II[.1u.1M RESPONSE PENDENT SPRINKLER VK302 (K5.6) The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-9459501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Visit the Viking wobsite for the latest edition of this technical data page: www.vikinggroupinc.com DESCRIPTION The Viking Microfast® Quick Response Pendent Sprinkler VK302 is a small ther- mosensitive glass bulb spray sprinkler available with various finishes and tempera- ture ratings to meet design requirements. The special Polyester and Electroless Nickel PTFE (ENT) coatings can be used in decorative applications where colors are desired. In addition, these coatings have been investigated for installation in corrosive environments and are Listed and Approved as indicated in the Approval Charts. LISTINGS AND APPROVALS ten cULus Listed: Category VNIV FM Approved: Class Series 2000 VdS Approved: Certificates G414009, G414010, G4040095, and 4880045 () LPCB Approved: Certificate 096e/06 7 www'PuftmkW~040V WARNING C rrn4 R*pccd*site n- CE Certified: Standard EN 12259-1 certificate of constancy of performance 0832-CPR-S0021 CCCF Approved: Approved by the China Certification Center for Fire Products (CCCF) 01 MED Certified: Standard EN 12259-1, EC-certificate of conformity 0832-MED-I 003 Refer to Approval Chart I and Design Criteria cULus Listing requirements, and refer to Approval Chart 2 and Design Criteria for FM Approval requirements that must be followed. TECHNICAL DATA Specifications: Minimum Operating Pressure: 7 psi (0.5 bar) Rated to 175 psi (12 bar) water working pressure Factory tested hydrostatically to 500 psi (34.5 bar) Thread size: 1/2" NPT, 15 mm BSP Nominal K-Factor: 5.6 U.S. (80.6 metric**) Glass-bulb fluid temperature rated to -65 °F (-55 °C) Overall Length: 2-1/4" (58 mm) *cULus Listing, FM Approval, and NFPA 13 installs require a minimum of 7 psi (0.5 bar). The minimum operating pressure for LPCB and CE Approvals ONLY is 5 psi (0.35 bar). Material Standards: Frame Casting: Brass UNS-C84400 or QM Brass Deflector: Phosphor Bronze UNS-051000 or Copper UNS-C19500 Bulb: Glass, nominal 3 mm diameter Belleville Spring Sealing Assembly: Nickel Alloy, coated on both sides with PTFE Tape Screw: Brass UNS-C36000 Pip Cap and Insert Assembly: Copper UNS-ClI000 and Stainless Steel UNS-530400 For Polyester Coated Sprinklers: Belleville Spring-Exposed For ENT Coated Sprinklers: Belleville Spring-Exposed, Screw and Pipcap - ENT plated. Ordering Information: (Also refer to the current Viking price list.) Order Quick Response Pendent Sprinklers by first adding the appropriate suffix for the sprinkler finish and then the appropriate suffix for the temperature rating to the sprinkler base part number. Finish Suffix: Brass = A, Chrome = F, White Polyester = M-/W, Black Polyester = M-/B, and ENT = JN Temperature Suffix: 135 °F (57 °C) = A, 155 °F (68 °C) = B, 175 °F (79 °C) = D, 200 °F (93 °C) = E, 286 °F (141 °C) = G Form No. F_033314 19.02.21 Rev 19.1 Replaces Form No. F_033314 Rev 18.1.P65 (Removed F-i Escutcheon.) Page 2 of 6 NIIQNG4 MICROFAST® QUICK I:II[.u'7M RESPONSE PENDENT SPRINKLER VK302 (K5.6) The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs©vikingcorp.com Visit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com For example, sprinkler VK302 with a Brass finish and a 155 OF (68 °C) temperature rating = Part No. 12979AB Available Finishes And Temperature Ratings: Refer to Table 1. Accessories: (Also refer to the current Viking price list.) Sprinkler Wrenches: Standard Wrench: Part No. 21475M/B. Wrench for Recessed Pendent Sprinklers: Part No. 13655W/B** (available since 2006) Optional Protective Sprinkler Cap Remover/Escutcheon Installer Tool*** Part No. 15915 (available since 2010) **A 1/s" ratchet is required (not available from Viking). ***Allows use from the floor by attaching a length of 1" diameter CPVC tubing to the tool. Ideal for sprinkler cabinets. Refer to Bulletin F_051808. Sprinkler Cabinets: Six-head capacity: Part No. 01724A (available since 1971) Twelve-head capacity: Part No. 01725A (available since 1971) INSTALLATION Refer to appropriate NFPA Installation Standards. OPERATION During fire conditions, the heat-sensitive liquid in the glass bulb expands, causing the glass to shatter, releasing the pip cap and sealing spring assembly. Water flowing through the sprinkler orifice strikes the sprinkler deflector, forming a uniform spray pattern to extinguish or control the fire. INSPECTIONS, TESTS AND MAINTENANCE Refer to NFPA 25 for Inspection, Testing and Maintenance requirements. AVAILABILITY The Viking Microfaste Quick Response Pendent Sprinkler VK302 is available through a network of domestic and international dis- tributors. See The Viking Corporation web site for the closest distributor or contact The Viking Corporation. GUARANTEE For details of warranty, refer to Viking's current list price schedule or contact Viking directly. Wrench Flat Protective Sprinkler Cap— Figure 1: Standard Sprinkler Wrench 21475M/B Form No. F_033314 19.02.21 Rev 19.1 Page 3 of 6 MICROFAST® QUICK N411QNG4 l.I:IIE.7M RESPONSE PENDENT SPRINKLER VK302 (K56) The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Visit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com TABLE 1: AVAILABLE SPRINKLER TEMPERATURE RATINGS AND FINISHES Sprinkler Temperature Sprinkler Nominal Maximum Ambient U Bulb Color Classification Temperature Rating' Ceiling Temperature' Ordinary 135 OF (57 °C) 100 °F (38 °C) Orange Ordinary 155 OF (68 °C) 100 °F (38 °C) Red Intermediate 175 °F (79 °C) 150 °F (65 °C) Yellow Intermediate 200 °F (93 °C) 150 °F (65 °C) Green High 286 °F (141 C) 225 °F (107 °C) Blue Sprinkler Finishes: Brass, Chrome, White Polyester, Black Polyester, and ENT Corrosion-Resistant Coatings': White Polyester, and Black Polyester. ENT in all temperature ratings except 135 °F (57 °C) Footnotes The sprinkler temperature rating is stamped on the deflector. 2 Based on NFPA-13. Other limits may apply, depending on fire loading, sprinkler location, and other requirements of the Authority Having Jurisdiction. Refer to specific installation standards. The corrosion-resistant coatings have passed the standard corrosion test required by the approving agencies indicated in the Approval Charts. These tests cannot and do not represent all possible corrosive environments. Prior to installation, verify through the end-user that the coatings are com- patible with or suitable for the proposed environment. For automatic sprinklers, the coatings indicated are applied to the exposed exterior surfaces only. Note that the spring is exposed on sprinklers with Polyester and ENT coatings. For ENT coated automatic sprinklers, the waterway is coated. Sprinkler wrench 13655W/B** for recessed pendent sprinklers ** A 1/2" ratchet is required (not available from Viking) Carefully slide the wrench sideways around the protective cap, ensuring engagement with the sprinkler wrench flats Figure 2: Wrench 13655W/B for Recessed Pendent Sprinklers Form No. F_033314 19.02.21 Rev 19.1 Page 4 of 6 NIKING MICROFAST® QUICK I RESPONSE PENDENT SPRINKLER VK302 (K5.6) The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269.945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Visit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com Approval Chart I (UL) The Viking Microfaste Quick Response KEY Pendent Sprinkler VK302 LZX~if-tl)e--',!~~ Maximum 175 PSI(12 Bar) WWP - Base Sprinkler Thread Size Nominal Overall Ustlnp and Approval* Part SIN _________ K-Factor Length (Refer also to De$19n Criteria) Number1 Style NPT __ BSP U.S. metric2 Inches mm cULus4 VdS LPCB 12979 VK302 Pendent 1/2" 15 mm 56 80.6 2-1/4 58 A1Z,B1Y,D2,C2X Al A1Z,B1Y DIZ,CIY 19780 VK302 Pendent 1/2" -- 56 80.6 2-1/458 -- 1 -- -- D3 21354 VK302 Pendent -- 15 mm 5.6 80.6 2-1/4 58 - 1 -- - — -. D3 06662B VK302 Pendent 112" 15 mm 5.6 80.6 2-1/4 58 lAlZ,BIYD2,C2XI -- -- - — 18021 VK302 Pendent 1/2" 15 mm 5.6 80.6 2-1/4 58 AiX, B1Y I Al I AiX, B1Y I Dlx, dY7 Dl -- Approved Temperature Ratings Approved Finishes Approved Escutcheons A- 135 °F (57 °C), 155 "F (68 "C), 175 "F 1 - Brass, Chrome, White X - Standard surface-mounted escutcheon or the (79 °C), 200 °F (93 "C) 286 "F (141 °C) Polyester 6, Black Polyes- Viking Micromatic® Model E-1 Recessed Escutcheon B - 135 °F (57 °C), 155 °F (68 °C), 175 °F ter5'6 Y - Standard surface-mounted escutcheon or recessed with the 'liking Micromatic® (79 °C), and 200 "F (93 °C) 2- ENT5 Model E-1, E-2, or E-3 Recessed Escutcheon C - 155 °F (68 "C), 175 "F (79 "C), and 3 - Chrome Z - Standard surface-mounted escutcheon 200 °F (93 "C) D - 155 °F (68 °C), 175 °F (79 °C), 200 "F (93 °C), 286 °F (141 "C) Footnotes Base part number shown. For complete part number, refer to Viking's current price schedule. 2 Metric K-factor measurement shown is when pressure is measured in Bar. When pressure is measured in kPa, divide the metric K-factor shown by 10.0. This table shows the listings and approvals available at the time of printing. Other approvals may be in process. Listed by Underwriters Laboratories Inc. for use in the U.S. and Canada. cULus Listed as corrosion-resistant. 6 Other colors are available on request with the same Listings and Approvals as the standard colors. CE Certified, Standard EN 12259-1, EC-certificate of constancy of performance 0832-CPR-50021. MED Certified, Standard EN 12259-1, EC-0832-MED-1003. DESIGN CRITERIA - _UL (Also refer to Approval Chart 1 above.) cULus Listing Requirements: The Viking Microfaste Quick Response Pendent Sprinkler VK302 is cULus Listed as indicated in the Approval Chart for installation in accordance with the latest edition of NFPA 13 for standard spray sprinklers. Designed for use in Light and Ordinary occupancies. The sprinkler installation rules contained in NFPA 13 for standard spray pendent sprinklers must be followed. IMPORTANT: Always refer to Bulletin Form No. F_091699 - Care and Handling of Sprinklers. Also refer to Form No. F_080614 for general care, installation, and maintenance information. Viking sprinklers are to be installed in accordance with the latest edition of Viking technical data, the appropriate standards of NFPA, LPCB, APSAD, VdS or other similar organizations, and also with the provisions of governmental codes, ordinances, and standards, whenever applicable. Form No. F_033314 19.02.21 Rev 19.1 Page 5 of 6 N I I(IF1G® MICROFAST® QUICK RESPONSE PENDENT SPRINKLER VK302 (K5.6) The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269.945.9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcsvikingcorp.com Visit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com Approval Chart 2 (FM) I eserats KEY The Viking Microfaste Quick Response F Pendent Sprinkler VK302 E2!!I Maximum 175 PSI (12 Bar) W'INP Base Part Sprinkler Thread Size Nominal K-Factor Overall Length FM Approval& Number' SIN Style (Refer also to Design Criteria.) NPT BSP U.S. metric2 Inches mm 12979 VK302 Pendent 1/2" 15 mm 5.6 1 80.6 2-1/4 58 A1Z, B1Y, D2X, C2 06662B VK302 Pendent 1/2" 15 mm 5.6 80.6 2-1/4 58 A1Z, B1Y, D2X, C2 18021 VK302 Pendent 1/2" 15 mm 1 5.6 80.6 2-1/4 58 A1Z, B1Y Approved Temperature Ratings Approved Escutcheons A - 135 °F (57 °C), 155 °F (68 °C), 175 °F (79 °C), 200 °F X - Standard surface-mounted escutcheon or the (93 °C), 286 °F (141 °C) Approved Finishes Viking Micromatic® Model E-1 Recessed B - 135°F (57 °C), 155°F (68 °C), 175°F (79 °C), and 1- Brass, Chrome, White Polyester4, Escutcheon 200 °F (93 °C) and Black Polyester4 Y - Standard surface-mounted escutcheon or recessed C - 155 °F (68 °C), 175 °F (79 °C), 200 °F (93 °C), 286 2 - ENT5 with the Viking Micromatic® Model E-1 or E-2 °F (141 °C) Recessed Escutcheon D - 155 °F (68 °C), 175 °F (79 °C), 200 °F (93 °C) Z - Standard surface-mounted escutcheon Footnotes Base part number shown. For complete part number, refer to Viking's current price schedule. 2 Metric K-factor measurement shown is when pressure is measured in Bar. When pressure is measured in kPa, divide the metric K-factor shown by 10.0. This table shows the FM Approvals available at the time of printing. Other approvals may be in process. Other colors are available on request with the same Approvals as the standard colors. FM approved as corrosion proofing for corrosive environments. DESIGN CRITERIA -FM (Also refer to Approval Chart 2 above.) The Viking Microfast® Quick Response Pendent Sprinkler VK302 is FM Approved as quick response Non-storage pendent sprinklers as indicated in the FM Approval Guide. For specific application and installation requirements, reference the latest applicable FM Loss Prevention Data Sheets (including Data Sheet 2-0). FM Global Loss Prevention Data Sheets contain guidelines relating to, but not limited to: minimum water supply requirements, hydraulic design, ceiling slope and obstructions, minimum and maximum allowable spacing, and deflector distance below the ceiling. NOTE: The FM installation guidelines may differ from cULus and/or NFPA criteria. IMPORTANT: Always refer to Bulletin Form No. F_091699 - Care and Handling of Sprinklers. Also refer to Form No. F_080614 for general care, installation, and maintenance information. Viking sprinklers are to be installed in accordance with the latest edition of Viking technical data, the appropriate standards of NFPA, FM Global, LPCB, APSAD, VdS or other similar organiza- tions, and also with the provisions of governmental codes, ordinances, and standards, whenever applicable. Form No. F_033314 19.02.21 Rev 19.1 Page 6 of 6 MICROFAST® QUICK 'J IKII1G lsIII[iU'7M.t RESPONSE PENDENT SPRINKLER VK302 (K5.6) The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs©vikingcorp.com Visit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com Ceiling Opening Size: 1/2" 2-5/16" (59 mm) minimum (15 mm) 2-1/2" (64 mm) maximum NPT L )*. Installed with a standard 1/8" surface-mounted escutcheon Figure 3: Sprinkler Dimensions with a Standard Escutcheon (5 mm) 1-3/4" (4 Installed with a Model E-1 Recessed Escutcheon 2" Installed with a Model E-2 Thread-on Recessed Escutcheon Ceiling Opening Size: 2-5/16" (59 mm) minimum 2-1/2" (64 mm) maximum AP 1-1/8" (29 mm) Mm. Figure 4: Sprinkler Dimensions with the Model E-1 and E-2 Recessed Escutcheons Form No. F_033314 19.02.21 Rev 19.1 Replaces Form No. F_033314 Rev 18.1.P65 (Removed F-i Escutcheon.) Page 1 of 4 MICROFAST® QUICK KJ '4 l:II[.qu.7..Iy RESPONSE UPRIGHT SPRINKLER VK300 (K5.6) The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269945.9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Visit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com DESCRIPTION The Viking Microfase Quick Response Upright Sprinkler VK300 is a small, thermosensitive, glass-bulb spray sprinkler available in several differ ent finishes and temperature ratings to meet design requirements. The spe- cial Polyester and Electroless Nickel PTFE (ENT) coatings can be used in decorative applications where colors are desired. In addition, these coat irlgs have been investigated for installation in corrosive atmospheres and are listed/approved as corrosion resistant as indicated in the Approval Charts. (Note: FM global approves the ENT coating as corrosion resistant. FM Global has no approval classification Polyester coatings as corrosion resistant.) LISTINGS AND APPROVALS cULus Listed: Category VNIV FM Approved: Classes 2002 and 2020 Refer to Approval Charts and Design Criteria for listing and approval requirements that must be followed. 0 WARNING, Cncec W R pmctve Kwr, 3. TECHNICAL DATA Specifications: Minimum Operating Pressure: 7 psi (0.5 bar)* Maximum Working Pressure: 175 psi (12 bar) wwp. Factory tested hydrostatically to 500 psi (34.5 bar) Testing: U.S.A. Patent No. 4,831,870 Thread size: 1/2" NPT, 15 mm BSP Nominal K-Factor: 5.6 U.S. (80.6 metric**) Glass-bulb fluid temperature rated to -65 °F (-55 °C) Overall Length: 2-3/16" (56 mm) *cULus Listing, FM Approval, and NFPA 13 installs require a minimum of 7 psi (0.5 bar). The minimum operating pressure for LPCB and CE Approvals ONLY is 5 psi (0.35 bar). Material Standards: Frame Casting: Brass UNS-C84400 or QM Brass Deflector: Brass UNS-C23000 or Copper UNS-C19500 Bulb: Glass, nominal 3 mm diameter Belleville Spring Sealing Assembly: Nickel Alloy, coated on both sides with PTFE Tape Screw: Brass UNS-C36000 Pip Cap and Insert Assembly: Copper UNS-ClI000 and Stainless Steel UNS-530400 For Polyester Coated Sprinklers: Belleville Spring-Exposed For ENT Coated SrinkIers: Belleville Spring-Exposed, Screw and Pipcap - ENT plated Ordering Information: (Also refer to the current Viking price list.) Order Viking Microfast® Quick Response Upright Sprinkler VK300 by first adding the appropriate suffix for the sprinkler finish and then the appropriate suffix for the temperature rating to the sprinkler base part number. Finish Suffix: Brass = A, Chrome = F, White Polyester = M-/W, Black Polyester = M-/B, and ENT = JN Temperature Suffix (°F/°C): 135°I57° = A, 155°/68° = B, 175°/79° = D, 200°/93° = E, and 286°/141° = G For example, sprinkler VK300 with a 1/2" NPT thread, Brass finish and a 155 °F/68 °C temperature rating = Part No. 12978AB Available Finishes And Temperature Ratings: Refer to Table 1. Accessories: (Also refer to the Viking website.) Sprinkler Wrench: Standard Wrench: Part No. 21475M/B (available since 2017) Sprinkler Cabinets: Six-head capacity: Part No. 01724A (available since 1971) Twelve-head capacity: Part No. 01725A (available since 1971) 4. INSTALLATION Refer to appropriate NFPA Installation Standards. Form No. F_052114 18.10.11 Rev 17.1.P65 Replaces Form No. F_052114 Rev 17.1 (Added P65 Warning.) Page 2 of 4 N II(iF1 c3 MICROFAST® QUICK RESPONSE UPRIGHT SPRINKLER VK300 (K5.6) The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Visit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com OPERATION During fire conditions, the heat-sensitive liquid in the glass bulb expands, causing the glass to shatter, releasing the pip cap and sealing spring assembly. Water flowing through the sprinkler orifice strikes the sprinkler deflector, forming a uniform spray pattern to extinguish or control the fire. INSPECTIONS, TESTS AND MAINTENANCE Refer to NFPA 25 for Inspection, Testing and Maintenance requirements. AVAILABILITY The Viking Microfast5 Quick Response Upright Sprinkler VK300 is available through a network of domestic and international distributors. See The Viking Corporation web site for the closest distributor or contact The Viking Corporation. GUARANTEE For details of warranty, refer to Viking's current list price schedule or contact Viking directly. TEMPERATURE RATINGS AND FINISHES Sprinkler Temperature Sprinkler Nominal Maximum Ambient Bulb Color Classification Temperature Rating' Ceiling Temperature' Ordinary 135 °F (57 °C) 100 °F (38 °C) Orange Ordinary 155°F(68°C) 100°F(38°C) Red Intermediate 175 °F (79 °C) 150 F (65 °C) Yellow Intermediate 200 °F (93 °C) 150 °F (65 °C) Green High 286 °F (141 °C) 225 °F (107 C) Blue Sprinkler Finishes: Brass, Chrome, White Polyester, Black Polyester, and ENT Corrosion-Resistant Coatings3: White Polyester, Black Polyester, and Black PTFE. ENT in all temperature ratings except 135 °F (57 °C) Footnotes The sprinkler temperature rating is stamped on the deflector. 2 Based on NFPA-1 3. Other limits may apply, depending on fire loading, sprinkler location, and other requirements of the Authority Having Jurisdiction. Refer to specific installation standards. The corrosion-resistant coatings have passed the standard corrosion test required by the approving agencies indicated in the Approval Charts. These tests cannot and do not represent all possible corrosive environments. Prior to installation, verify through the end-user that the coatings are compat- ible with or suitable for the proposed environment. For automatic sprinklers, the coatings indicated are applied to the exposed exterior surfaces only. Note that the spring is exposed on sprinklers with Polyester, ENT, and PTFE coatings. For ENT coated automatic sprinklers, the waterway is coated. Protective Sprinkler Cap Wrench Flat Figure 1: Standard Sprinkler Wrench 21475M1B Form No. F_052114 18.10.11 Rev 17.1.P65 Page 3 of 4 b MICROFAST® QUICK RESPONSE UPRIGHT SPRINKLER VK300 (K5.6) The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269.945.9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Visit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com Approval Chart I (UL) ICEY Microfaste Quick Response ti " I AIX 4 Upright Sprinkler VK300 Maximum 175 PSI (12 bar) WWP Base Part Thread Size Nominal K-Factor Overall Length Listings and ApprovaIs Number' SIN NPT BSP U.S metric2 Inches mm cULus VdS LPCB I NYC 12978 VK300 1/2" 15 mm 5.6 80.6 2-3/16 56 Al, B2 -- -- See footnote 7. - 06661B VK300 1 1/2" 15 mm 1 5.6 80.6 1 2-3/16 56 1 Al, B2 I -- See f00tnote7J Approved Temperature Ratings Approved Finishes A- 135 °F (57 °C), 155 °F (68 °C), 175 °F (79 °C), 200°F (93 °C), and 1 - Brass, Chrome, White Polyester56, and Black Polyester56 °F 286 (141°C) B - 155 °F (68 °C), 175 °F (79 °C), 200 °F (93 °C), and 286 °F (141°C) 2 - ENT6 Footnotes Base part number is shown. For complete part number, refer to Viking's current price schedule. Metric K-factor measurement shown is when pressure is measured in Bar. When pressure is measured in kPa, divide the metric K-factor shown by 10.0. 3This table shows the listings and approvals available at the time of printing. Check with the manufacturer for any additional approvals. Listed by Underwriters Laboratories Inc. for us in the U.S. and Canada Other colors are available on request with the same Listings and Approvals as the standard colors. 6 cULus Listed as corrosion resistant. Meets New York City requirements, effective July 1, 2008 Accepted for use, City of New York Board of Standards and Appeals, Calendar Number 219-76-SA and City of New York Department of Buildings, MEA 89-92-E, Vol. 16. DESIGN CRITERIA -UL (Also refer to Approval Chart 1 above.) cULus Listing Requirements: The Viking Microfast® Quick Response Upright Sprinkler VK300 is cULus Listed as indicated in Approval Chart 1 for installation in accordance with the latest edition of NFPA 13 for standard spray sprinklers. Designed for use in Light and Ordinary Hazard occupancies. The sprinkler installation rules contained in NFPA 13 for standard spray upright sprinklers must be followed. IMPORTANT: Always refer to Bulletin Form No. F_091699 - Care and Handling of Sprinklers. Also refer to Form No. F_080614 for general care, installation, and maintenance information. Viking sprinklers are to be installed in accordance with the latest edition of Viking technical data, the appropriate standards of NFPA, FM Global, LPCB, APSAD, VdS or other similar organizations, and also with the provisions of governmental codes, ordinances, and standards, whenever applicable. Form No. F_052114 18.10.11 Rev 17.1.P65 Page 4 of 4 IK1NG u.7 MICROFAST® QUICK l:IIr..Iv RESPONSE UPRIGHT SPRINKLER VK300 (K5.6) The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Visit the Viking websito for the latest edition of this technical data page: www.vikinggroupinc.com Approval Chart 2 (FM) Microfase Quick Response 4 ,. Upright Sprinkler VK300 Maximum 175 PSI (12 bar) WWP Base Part Thread Size Nominal K-Factor Overall Length FM Approvals3 Number1 SIN (Refer also to Design Criteria below.) NPT BSP U.S. metric2 Inches mm 12978 VK300 1/2" 15 mm 5.6 80.6 2-3/16 56 Al, B2 06661B VK300 1/2" 1 15 mm 5.6 80.6 2-3/16 56 I Al, B2 Approved Temperature Ratings Approved Finishes A- 135 °F (57 °C), 155 °F (68 °C), 175 °F (79 °C), 200 °F (93 °C), and 286 °F (141°C) 1 -Brass, Chrome, White Polyester', and Black B - 155 °F (68 °C), 175 °F (79 °C), 200 °F (93 °C), and 286 °F (141°C) rl Polyes e 2 - ENT Footnotes 1 Base part number is shown. For complete part number, refer to Viking's current price schedule. 2 Metric K-factor measurement shown is when pressure is measured in Bar. When pressure is measured in kPa, divide the metric K-factor shown by 10.0. 'This table shows the FM Approvals available at the time of printing. Check with the manufacturer for any additional approvals. Other colors are available on request with the same Approvals as the standard colors. 6 FM approved as corrosion resistant. DESIGN CRITERIA - FM (Also refer to Approval Chart 2 above.) FM AoDroval Requirements: The Microfast® Quick Response Upright Sprinkler VK300 is FM Approved as a quick response Non-Storage upright sprinkler as indicated in the FM Approval Guide. For specific application and installation requirements, reference the latest applicable FM Loss Prevention Data Sheets (including Data Sheet 2-0). FM Global Loss Prevention Data Sheets contain guidelines relating to, but not limited to: minimum water supply requirements, hydraulic design, ceiling slope and obstructions, minimum and maximum allowable spacing, and deflector distance below the ceiling. NOTE: The FM installation guidelines may differ from cULus and/or NFPA criteria. IMPORTANT: Always refer to Bulletin Form No. F_091699 - Care and Handling of Sprinklers. Also refer to Form No. F_080614 for general care, installation, and maintenance information. Viking sprinklers are to be installed in accordance with the latest edition of Viking technical data, the appropriate standards of NFPA, FM Global, LPCB, APSAD, VdS or other similar organizations, and also with the provisions of governmental codes, ordinances, and standards, whenever applicable. Form No. F_052114 18.10.11 Rev 17.1.P65 Replaces Form No. F_052114 Rev 17.1 (Added P65 Warning.) 93(gNIEPULIM IJ1 QJnn BuR Moose Tube's° Schedule 10 and Schedule 40 are FM Approved and UI. Listed (for US. and Canada), even though these products do not require separate approvals and listings. Bull Moose Tube° made the decision to have them approved and listed. Our Schedule 10 and Schedule 40 have a pressure rating of 300 PSI and have been through the same rigorous testing as our other line pipe products. Schedule 10 can be supplied roll grooved or plain end. Bull Moose Tube's° Schedule 10 and Schedule 40 pipes are hot dipped galvanized to meet ASIM Al 23 standards. All products are stencilled to meet FM & UL specifications. ni SCHEDULE 10 PIPE SPECIFICATIONS NOMINAL PIPE 0D ID. WATER FILLED BUNDLE SIZE (IN) (IN) (IN) CRR** WEIGHT/FT WEIGHT SIZE 1 1.315 1.097 15.27 1.41 lbs/ft 1.820 91 1-114 1.660 1.442 9.91 1.81 lbs/ft 2.518 61 1-1/2 11900 1.682 7.76 2.09 lbs/ft 3.053 61 2 2375 2.157 6.27 2.64 lbs/ft 4.223 37 2-1/2 2.875 2.635 4.92 3.53 lbs/ft 5.893 30 3 3.500 3.260 354 4.34 lbs/ft 7.957 19 4 4.500 4.260 2.50 5.62 lbs/ft 11.796 19 Ji [Of j[à) NOMINAL PIPE 0.D. 1.0. WATER FILLED BUNDLE SIZE (IN) (IN) (IN) CRR** WEIGHT/FT WEIGHT SIZE 1 1.315 1.049 1.00 1.68 lbs/ft 2.055 70 1-1/4 1,660 1.380 1.00 2.27 lbs/ft 2.918 51 1-1/2 1.900 1.610 1.00 2.72 lbs/ft 3.602 44 2 2.375 2.067 1.00 3.66 lbs/ft 5.114 30 21/2* 2.875 2.468 1.00 5.80 lbs/ft 7.875 30 3* 3.500 3.068 1.00 7.58 lbs/ft 10.783 19 4* 4.500 4.026 1.00 10.80 lbs/ft 16.316 19 Vrtf available in CM GrantkA Wm9on Resse Ratio per latest Ut. Oectoy Lfstn PIPE PREPARATION For proper operation, all pipe surfaces should be cleaned prior to installation. In order to provide a leak-tight seat for the gasket pipe surfaces should be free from indentations and projections from the end of the pipe to the groove. All loose paint, scale, dirt, chips, grease, and rust must be removed prior to installation. Failure to take these important steps may result in improper coupling assembk causing leakage. Also, check the manufacturer's instructions for the specific fitting used. Q For Additional Information Contact (800) 32S-4467 WWW builmoosetube corn Or From Canada Call: (800) 882-4666 saies@huilrnoosetube.com - 1819ClanRoad thestfiktM0 Gerald. MO Kent WA CasaGrande.AZ Dallas,IX man OH 63017 LE Ll M01 ff Bull Moose iube's°Eddythread40° ADVANTAGES OF BULL MOOSE TUBE° EDDYTHPEAD 400 is a lightweight replacement for • Has a Corrosion Resistance Ratio of 11.0 Schedule 40 that has a Corrosion • Has a pressure rating of 300 psi. Resistance Ratio of 1. • Is lighter weight than Schedule 40. Is approved by Factory Mutual and listed by Underwriters Laboratories. Is produced in accordance to ASTM Al 35 and A795 Type E, Grade A. Can be used with standard Schedule 40 threaded fittings, couplings, and valves. Is produced from steel with excellent properties of strength and threadability. Can be used in wet, preadion, and deluge type sprinkler systems. Can be hot dipped galvanized to meet FM's requirement for dry systems. Offers lower freight costs. Supplied with EDDY GUARD 110 MIC preventative coating. EODVTHREAD 400 SPECIFICATIONS NOMINAL PIPE QM ID. WEIGHT WATER FILLED BUNDLE SIZE (IN) (IN) (IN) CRR* LBJFT WEIGHT SIZE 1 1.295 1.083 1.00 1.461 1.860 70 1-114 1.650 1.418 1.00 2.070 2.754 51 1-1/2 1.900 1.654 1.00 2.547 3.468 44 2 2.375 2.123 1.00 3.308 4.842 30 'twe1en Rtie Ratio peck Iatet UL Diredety listing PIPE PREPARATION For proper operation, all pipe surfaces should be cleaned prior to installation. in order to provide a teak-tight seat for the gasket pipe surfaces should be free from indentations and projections from the end of the pipe to the groove. All loose paint. scale, dirt, chips, grease, and rust must be removed prior to installation. Failure to take these important steps may result in improper coupling assembly. causing leakage. Also, check the manufacturer's Instructions for the specific fitting used. Q For Additional Information Contact (800)325-4461 www.bullmoosetube.com Or From Canada Call: (800) 882-4666 salesbulIrnoosethbe.com 8, 1819claiksonRoad chestediekI. MO Getaki, MO Kent WA Casa GrandAZ Da1ks,1X Mas*t OH 63017 IIEKS- 4t! L!E 1108 XMIJaIii Fj L ' R- E A-7 I D'!" R.L Dull Moose Tube's Eddylite° is U a lightwall threadable pipe manufactured in NI'S 1 through 2. Eddylite° is a truly unique product within the fire protection industry. This product has been engineered to provide lower cost fire protection systems without compromising service life, adequate wall thickness, or standard outside diameter, Eddy, lite° is manufactured to meet the requirements of ASTM Al 35 and A795 specifications. This pipe product has been fully approved by Factory Mutual, and listed by Underwriters Laboratories (for U.S. and Canada) for use in fire protection systems with a working pressure of 300 psi or less. 6 ADVANTAGES OF BULL MOOSE TUBE° EDDYLITE° Standard outside diameter, unlike some other lightwall threadable pipe products. tighter in weight than Schedule 40. Superior burst strength and corrosion resistance ratio compared to other lightwall threadable pipe products. S Exceptionally strong, meets or exceeds ASTM Al 35 minimum yield requirements. Can be used with standard couplings fittings, and valves. Freight savings. Lower sprinkler system casts without compromising service life. Better hydraulics than Schedule 40. Wall thickness and weight close to Schedule 30: compare to other lightwall threadable water filled products with wail thickness less than Schedule 10! CORROSION RESISTANCE RATIO (CRR) NOMINAL STANDARD INSIDE UL UL WEIGHT WATER BUNDLE PIPE SIZE (IN) am (IN) DIAMETER (IN) THREADED UNTHREADED PER FT FILLED SIZE 1 1.315 1.137 0.13 7.47 1.260 1.700 91 1-114 1.660 1.482 0.08 4.79 1.617 2.364 61 1412 1.900 1,712 0.12 4.53 1.967 1965 61 2,375 2.177 0.16 4.31 2.617 4.230 37 'Coto Rs1nce Ratb pu Latt UL Diredoy Listing PIPE PREPARATION For proper operation, all pipe surfaces should be cleaned prior to installation. In order to provide a leak-tight seat for the gasket, pipe surfaces should be free from indentations and projections from the end of the pipe to the groove. All loose paint, scale, dIrt, chips, grease, and rust must be removed prior to installation. Failure to take these important steps may result in improper coupling assembly, causing leakage. Also, check the manufacturer's instructions for the specific fitting used. C For Additional Information Contact (800) 325-4467 www.bullmoosetubexom Or From Canada Call: (800) 882-4666 sales@buHmoosetube.com 1819 cIation Road CheterfithLM0 Geckt,MO Kent.WA Qua Grande. AZ DaTX PJb3u30H ML 63017 [EiW [ESjiFE E IiE E Dull MooseTube's° EddyFlow° ADVANTAGES OF BULL MOOSE TUBE° EDDY FLOW° I) is a specially engineered Certified to ASTM Al 35 and A195 Type E, Grade A. replacement for Schedule 10, FM approved for roil grooving and welding for use in wet systems. offering better flow characteristics UL Listed (for U.S. and Canada) for joining by welding or by listed rubber gasketed fittings for use in wet, dry, preaction, and deluge type while providing design tlexibility sprinkler systems. This product is FM approved, as well Lightweight - saves shipping costs and offers easier handling. as lii Listed (for U.S. and Canada) Can be used with roll grooved couplings or welded outlets for pressures up to 300 psi. for roll grooving and welding. Can be supplied roil grooved or plain end. Can he hot dipped galvanized to meet FM's & UL requirement for dry systems. As an added benefit, it is more Supplied with EDDY GUARD 110 MIC preventative coating. economical to use than Schedule 10 due to reduced delivery costs - and ease of handling. Furthermore, NPS QD, EDDY FLOW EDDY FLOW WEIGHT WATER FILLED BUNDLE Eddy Flow's0 larger ID provides SIZE (IN) (IN) (ID) CRR PER Ft Wt SIZE an opportunity for downsizing - - and further cost savings. 1114 1.660 1.530 198 1.222 2.019 61 11/2 1.900 1.728 3.44 1.844 2.860 61 2 2,375 2.203 2.78 2.330 3.982 37 2-112 2.875 2.705 1.66 2.809 5.299 30 3 3.500 3.334 1.00 3,361 7.144 19 4 4500 4.310 1.00 4,968 11.290 19 WlswKe Ratio per tamst UL 0fret0ry Usting PIPE PREPARATION For proper operation, all pipe surfaces should be cleaned prior to installation. in order to provide a leak-tight seat for the gasket, pipe surfaces should be free from indentations and projections from the end of the pipe to the groove. All loose paint scale, dirt chips, grease, and rust must be removed prior to installation. Failure to take these important steps may result in improper coupling assembly causing leakage. Also, check the manufacturer's instructions for the specific fitting used. c®us LISTED <9> C;] OMFU NFPA ( For Additional Information contact (800) 325-4461 www.bullmoosetube.com Or From Canada Call, (800) 882-4666 salesbuUmoosetuhe.com 1819 tlarkson Road thesterfiekLM0 Gecakl,MO Kent WA CasaGrande,AZ DaflasTX Ma0H WL 63017 cJcDCu _ xt Bull Moose Tube's° Ultra Edd?' is ADVANTAGES OF BULL MOOSE TUBE° ULTRA EDDY° a versatile product that can be e Certified to ASTM Al 35 and A795 Type E. Grade A. roll grooved, welded, and used with • FM approved for roll grooving and welding for use in wet systems. Pressfit* Products. • UL listed (for U.S. and Canada) for joining by welding or by listed rubber gasketed fittings for use in wet, dry, preaction, and deluge type sprinkler systems. Lightweight— saves shipping costs, offers easier handling. Multidimensional: Can be used with all Schedule 5 approved roll grooved, welding and Pressfit* Products for pressures up to 175 psi. Designed to generic Schedule S tolerances for easy interchangeability with all approved or listed fittings. can be supplied roll grooved or plain end. With a larger ID than other products on the market today. Ultra Eddy offers substantial improvements in hydraulics. This improvement allows for downsizing within the system which offers the opportunity for additional cost savings. Can be hot dipped galvanized to meet FM'S requirement for dry systems. - - NPS 0.0. ULTRA ULTRA EDDY' WEIGHT WATER BUNDLE (IN) (IN) EDDY' (ID) CRR** PER FT FILLED WI SIZE 1 1.315 1.201 2.17 .868 1.359 91 1-1/4 1.660 1.546 1.40 1.107 1.920 61 11F2 1.900 1.786 1.11 1.274 2.360 61 2 2.375 2.261 1.00 1.604 3.344 37 Re d1rdemark ok company otAmeika '4 Corot Restane Rathpe Lde* UL fledoy Listing 8 c®us LISTED 4FPA '= PIPE PREPARATION For proper operation, all pipe surfaces should be cleaned prior to installation. In order to provide a leak-tight seat for the gasket, pipe surfaces should be free from indentations and projections from the end of the pipe to the groove. All loose paint, scale, dirt, chips, grease, and rust must be removed prior to installation. Failure to take these important steps may result in improper coupling assembtv. causing leakage. Also, check the manufacturer's instructions for the specific fitting used. Q For Additional Information Contact (800) 325-4467 www.bullmoosetubecom Or From Canada Call: (800) 882-4666 salesbulhnoosetube.tom 1819 Claron Road Chesterfield. MO GefakLM0 Kent WA CasaGande,AZ Dafla,TX MIS" OH 63017 T-E&ITrE ZE sYii MA NPS(IN) 1 1-114 1-112 2 2-112 3 4 aairi 1.315 1.660 1.900 2.375 LD.in 1.201 1.546 1.786 2.261 ULTRA EDDYO EmptyWe4tOMt) 0.868 1.107 1.274 1.604 Water-filledYit (Ih?ft) 1.359 1.920 2.360 3.344 CPR. 2.17 1.40 1.11 1.00 1 OLD.) 1.660 1.900 2.375 2.875 3.500 4.500 LLAin 1.530 1.728 2.203 2.705 3.334 4.310 1.222 1.844 2.330 2.809 3,361 4.968 EDDY FLOW Water-Riled Weight M 2.019 2.860 3.982 5.299 7.144 11.290 C.R.R. 1.98 3.44 2.78 1.66 1.00 1.00 1.315 1.660 1.900 2,375 2.875 3.500 4500 LD.in 1.097 1.442 1.682 2.157 2,635 3.260 4,260 SCHEDULE EmptyYightMt 1.410 1.810 2.090 2.640 3.530 4.340 5.620 tJednOhfft), 1.820 2.518 3.053 4.223 5.893 7.957 11,796 C.R.R. 15.27 9.91 7.76 6.27 4.92 3.54 2.50 0.EX(iñ) 1.315 1.660 1.900 2.375 LD.(in) 1.137 1.482 1.712 2.177 EDDYLITE° EmptyWeghtO&ft 1.260 1.617 1.967 2.617 Water-Filled 1.700 2.364 2.965 4.230 - j 0.13 0.08 0.12 0.16 o.a bi 1.295 1.650 1.900 2.375 LD.n} 1,083 1.418 1.645 2.123 EDDYTHREAD EmptyWeitObft 1.461 2.070 2.547 3.308 VtFiILed Weight Oh'ft): 1.860 2.754 3,468 4.842 C.R.R. 1.00 1.00 1.00 1.00 1.315 1.660 1.900 2.375 2.875 3.500 4.500 ulcin) 1.049 1.380 1.610 2,067 2.469 3.068 4.026 SCHEDULE Empty Weight Ohlft} 1.680 2.270 2.720 3.660 5.800 7.580 10.800 40 eJightØfQ 2.055 2.918 3.602 5.114 7.875 10.783 16.316 C.R.R. 1.00 1.00 1.00 1.00 1.00 1.00 1.00 0 For Additional Information Contact (800) 325-4467 wwwbuItmoosetube.com Q Or From Canada Call, (800) 882-4666 sates@bultmoosetube.tom 1819 Clarkson Road ChesteththtM0 Gerald, MO Keit,WA Cam Gande,AZ DaUaTX M0H 63017 9 NPS PIPE WEIGHT PIECES WEIGHT WEIGHT WEIGHT TYPE PER FOOT PER BUNDLE PER BUNDLE PER BUNDLE PER BUNDLE c®us LISTED 4ONA — ULTRA EDDY* SCHEDULE 10 1 EDDYUTE° - EDDYThREAD 40 SCHEDULE 40 ULTRA EDDY EDDY FLOW* SCHEDULE 10 1-114 EDDYLITE° EDDYThREAD 4(P SCHEDULE 40 • ULTRA EDDY EDDY FLOW* SCHEDULE 10 1-il 2 EDDYUTE° EDDYTH READ 400 SCHEDULE 40 ULTRA EDDY EDDY FLOW SCHEDULE 10 2 EDDyLITEe EDDYTHREAD 400 SCHEDULE 40 EDDY FLOW* 2-1/2 SCHEDULE 10 SCHEDULE 40 EDDY FLOW* 3 SCHEDULE 10 SCHEDULE 40* EDDY FLOW 4 1 SCHEDULE 10 SCHEDULE 40 6 SCHEDULE 10 8 SCHEDULE 10 0.868 91 1,659 1.896 1,975 1.410 91 2,695 3,079 3.208 1,260 91 2,408 2,752 2.867 1.461 70 2,148 2,454 2,557 1.680 70 2,470 2,822 2,940 1107 61 1,418 1.621 1.688 1,222 61 1,565 1,189 1,864 1.810 61 2,319 2,650 2,760 1.617 61 2,071 2,367 2.466 2.070 51 2,217 2,534 2.639 2,270 51 2,431 2,778 2,894 1.274 61 1,632 1,865 1,943 1.844 61 2,362 2,700 2,812 2.090 61 2,677 3,060 3.187 1.967 61 2,520 2,880 3,000 2.547 44 2,353 2,690 2,802 2.720 44 2,513 2,872 2,992 1.604 37 1,246 1,424 1,484 2.330 37 1,810 2,069 2,155 2.640 37 2,051 2,344 2,442 2.617 37 2.033 2,324 2,421 3.308 30 2,084 2.382 2,481 3.660 30 2,306 2,635 2,745 2.809 1,770 2.022 2.107 3.530 30 2.224 2,542 2,648 5.800 3,654 4,176 4,350 3.361 1.341 1,533 1,596 4.340 19 1,732 1,979 2,062 7.580 3,024 3,456 3,601 4.968 1,982 2,265 2,360 5.620 19 2.242 2,563 2,670 10.800 4,309 4,925 5,130 9.289 10 1,951 2,229 2,322 16.940 7 2,490 2,846 2,965 10 Onaibie in Casa Cinde.AL 1819 Clarkson Road Chesterfield, MO 63011 PHONE: (800) 325-4467 FAX: (636) 531-2645 www.buUmoosetube.com salesbuLimoosetube.cam BIL ELL![BTE EI lJRK L!E eie Bull Moose Tube EDDY FLOW Steel Pipe Joined by Threading, Bonding or CompressionlGrooved Couplings Max Zone of Influence Load (Fpw) lbs. Max. Transverse and 4-way Brace Spacing (ft.) According to HLF for the 2006 & 2009 IBC (ASCE7-05 ) & Q for NFPA-13 shown in BOLD TYPE Pipe Transverse Brace Spacing* Size 20ft. 25 ft. 30 ft. 35 ft. 40 ft. 015 0.50 0.75 1.001 1.251 1.50 1.715 2.00 12.25 2.50 2.75 3.00 1 114 136 109 89 76 64 40 40 37 32 29 26 24 23 21 20 19 18 1112 232 185 152 130 109 40 40 40 35 31 29 27 25 23 22 21 20 2 372 297 244 209 175 40 40 40 38 34 1 31 28 27 25 24 23 22 2112 549 440 360 309 258 40 40 40 40 36 32 30 28 26 25 24 23 3 809 648 531 4 51 381 40 1 40 i 40 1 4 37 34 31 1 29 28 26 25 24 4 1544 1235 1012 867 726 40 40 40 40 40 37 34 32 30 29 28 26 Bull Moose Tube EDDYTHREAD 40 Steel Pipe Joined by Threading, Bonding or CompressioniGrooved Couplings Max Zone of Influence Load (Fpw) lbs. Max. Transverse and 4-way Brace Spacing (ft.) According to HLF for the 2006 & 2009113C (ASCE ) & Cp for NFPA-13 shown in BOLD TYPE Pipe Transverse Brace Spacing Size 20 ift7, 25f1 3011. 3511. 40 ft. 0.25 1 0.50 0.75 1.00 1.25 1.50 1.75 2.00 2.25 1 2.50 12.75 3.00 1 119 95 78 67 56 40 40 36 31 28 25 24 22 21 20 19 18 11/4 218 175 143 123 103 40 40 40 35 31 28 26 25 23 22 21 20 1112 312 250 205 175 147 40 40 40 37 33 30 28 26 25 23 22 21 2 518 414 339 291 1 243 40 40 40 40 36 33 30 1 29 27 26 24 23 c®us LISTED u emu NFPA ( ForAdditional Information Contact (800) 325-4467 www.bulImoosetube.com Or From Canada Call: (800) 882-4666 salesbuIlmoosetube.corn 1819 Clarkson Road ChestefithtM0 GefakIM0 Kent. WA CaaGande DallTX Ms0H 00 WAMW 63017 11 MechanicaIV STYLES 920 AND 920N 5TY5 920 AND 920N STYLE 920 CROSS PATENTED Victaulic MechanicalTe Outlet provides a direct branch connection at any location a hole can be cut in pipe, The hole is cut oversize to receive a "holefinder" locating collar which secures the outlet in position permanently. A pressure responsive gasket seals on the pipe O.D. Cross-type connections can be achieved by utilizing two upper housings of the same style and size, with the same or differing branch size connections. NOTE: Style 920 and Style 920N housings cannot be mated to each other to achieve a cross connection. Style 920 and Style 920N Mechanical-T outlets are available with grooved or female threaded outlet. Specify choice on order. Units are supplied painted with plated bolts. Galvanized hous- ings are available, supplied with plated bolts. All sizes of Style 920 and 920N are rated at 500 psi/3450 kPa working pressure on Schedule 10 and 40 carbon steel pipe. They may also be used on high density polyethylene or poly- butylene (HDPE) pipe. Pressure ratings on HOPE are dependent an the pipe rating. Contact Victaulic for ratings on other pipe. Style 920 and 920N are not recommended for use on PVC plastic pipe. Standard piping practices dictate that the Mechanical-T Styles 920 and 920M must be installed so that the main and branch connections are a true 90° angle when permanently attached to the pipeline surface. Additionally, the Vic-Tap Il® hole cutting tool, which allows for hole cutting capabilities on pressurized systems, utilizes the Style 920 Mechanical-T in conjunction with the Series 726 Vic-Ball Valve to create the Style 931 Vic-Tap II Mechanical-I unit, See page 8 for further information, MATERIAL SPECIFICATIONS Housing/Coating: Ductile iron conforming to ASTM A-536, grade 6-4-12, with orange enamel coating, Ductile iron conforming to ASTM A-395, grade 65-45-15, is available upon special request. Optional: Hot dipped galvanized Gasket: (Specify choice*) Grade "E' EPDM EPDM (Green color code). Temperature range —30°F to +230°F/-34°C to +110°C. Recommended for cold and hot water service within the specified temperature range plus a variety of dilute acids, oil-free air and many chemical services. UL Classified in accordance with ANSI/NSF 61 for cold +86°F/+30°C and hot +180°F/+82°C. NOT RECOMMENDED FOR PETROLEUM SERVICES, Grade °T" nitrile Nitrile (Orange color code), Temperature range —20°F to +180°F/-29°C to +82°C. Recommended for petroleum products, air with oil vapors, vegetable and mineral oils within the specified temperature range. Not recommended for hot water services over +150°F/+66°C or for hot dry air over +140°F/+60°C. *Services listed are General Service Recommendations only. It should be noted that there are services for which these gaskets are not recommended. Reference should always be made to the latest Victaulic Gasket Selection Guide for specific gasket service recommendations and for a listing of services which are not recommended. Bolts/Nuts: Heat-treated plated carbon steel, trackhead meeting the physical and chemical requirements of ASTM A-449 and physical requirements of ASTM A-183. JOB/OWNER CONTRACTOR ENGINEER System No, Submitted By Spec Sect Para__________ Location Date Approved Date www.vlctaullc.com vICTAuLIC IS A REGISTERED TRADEMARK or VICTAIJLIC COMPANY C 2011 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REV U \,htauIic" 11.02-i FEMALE THREADED OUTLET Provides a direct branch connection at any location where a hole can be cut in the pipe A pressure responsive gasket provides the seal Request Publication 11.03 for Mechanical-T cross assemblies Pressure rated up to 500 psi/3450kPa on steel pipe; also available for use with HDPE pipe Sizes from 2 x 1/2'750 x 15 mm through 8 x 4/200 x 100 mm CARBON STEEL PIPE , HOLE CUT PRODUCTS 11.02 Mechanical-r Bolted Branch Outlets STYLES 920 AND 920N DIMENSIONS IMPORTANT NOTES; Style 920 and Style 920N housings cannot be mated to one another to achieve cross connections. Z25J'f1? ' Ii 0 193 )iT1sa 0' 'rair Lii: 1E '? Jr,Ea fi lraw '1193 4 tRe 2 x ½ (a)a 500 1.50 200 253 - 1.61 5.35 2.75 3.1 50 15 3450 38.1 51 64 41 136 70 1.5 3/4 (al a 920½ 500 .50 1.97 2.53 1,61 5.35 2,75 31 - 20 I 3450 33,1 50 64 41 136 70 1,5 (a) 500 500 1501.852.53 - 161535 2.75 3.0 - 25 3450 38.1 47 64 41 136 70 14 -. 1¼ lal ai 500 1,75 2,05 2.75 3.00 1.61 535 3.00 3.5 3.2 32 3450 44.5 52 70 76 41 136 76 1.7 1.5 11/2 (a) Sal 500 1.75 + 2.03 - 2.75 3.12 1.61 5.35 3.25 3,6 32 40 3450 445 52 70 79 41 136 83 1.7 1.5 2½ , ½¼)sai - 500 150 2.21 - 2.74 1.82 5.64 2.75 3.0 65 15 ' " 3450 381 56 70 143 70 1A -7 (a) 500 1.50 2.18 2.74 182 5.64 2.75 3.0 9204 23 3453 381 55 70 46 143 70 1.4 - 500 1,50 2.74920N 2.06 - 1.82 5.44 2.75 2.9 25 3450 361 52 70 - 46 143 70 1/ 7 )) 920114 - 500 1,75 2.30 3.00 3.25 182 6.29 3.00 3.5 ' 3.2 ' 32 3450 44.5 53 76 83 , 46 160 76 1.7 15 I/a t (a)e 940N 500 2' 228 300 3,25 182 646 325 36 3 40 3450 50.8 58 76 33 46 159 83 1.7 1.6 76.1 x /2(a) 300 u 222 775 225 346 318 39 15 2065 38.1 56 70 57 164 81 1.8 / (a) I 9201 300 1.50 2.19 275 2 25 646 318 39 20 i, 2065 38,1 56 70 57 164 81 8 1(a) 90N 300 ' .50 ' 27 275 2.25 6,6 3.18 3.8 25 , 2065 , 38.1 53 70 57 16 81 1.7 , - 1¼a)ai92 N 500 th 175 230 3.00 3.31 192 5.29 300 3.5 3.2 32 3450 44.5 58 76 84 49 160 76 16 1.5 1½ (a) 920¼ 500 2,00 - 2,28 3.00 331 1.92 6.29 3.25 3.5 3.3 ' 40 3450 , 50.8 58 76 84 49 160 83 1.6 1,5 3 ½ (a) a I 92(N 500 1.50 2.52 3.05 - 2.23 6.15 275 3.4 80 15 345038.1 54 78 58 156 , 70 , 1.6 , 3/ 'ala 92 ½ 500 150 249 305 - //8 61 75 34 L__4 3450 38.1 , 63 78 , 53 56 , 70 - 1.6 1(a) 1920½ 500 750 2.38 3.06 - 2.28 6,15 2,75 3.3 - 25 I ' 3450 381 61 78 53 , 156 , 70 1.6 1¼ (a) 3a 920'S 500 3450 1.75 2.55 65 3.25 3.55 90 2.28 6,15 156 3,00 76 3.8 1.8 3.7 1.8 )b) 32 44.5 3 58 , , 1½ (a) 92014 500 2½0 2,783.50 3.56 2.28 6.15 3.25 4.1 3,8 40(b) ' 3450 50,8 71 89 90 58 155 83 1.9 1.8 2 (a) 4 ½ 920 500 2.50 2.75 3.50 3.56 2.28 6.75 3.88 4.9 4.6 50 3450 635 70 89 90 58 172 99 23 27 3/a x 2 ,, 920½ 500 2.50 s.00l"' 3,75 2,44 6.72 388 38 90 o 3450 335 76 I 95 62 171 99 I 1.8 Center of run to engaged pipe end, female threaded outlet only (dimensions approximate). t Avaf able with grooved or female threaded outlet. Specify choice on order, Center of run to end of fitting, S Female threaded outlets are available to bIPT and BSPT soeclfications. @ See page 7 for Fire Protection approvals and pressure ratings, (a) British Standard female pipe threaded outlet is available as listed. Specify "BSPT" clearly on order, (b)For 76,1 mm threaded outlet, specify 2½' BSPT clearly on order. § Jds approved for fire protection services 0 LPCB approved for fire protection services 0 Approved for use in China by Tianjin Approvals Company. www.vjctaulic.com vlcTAuuc IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. 2017 VICTAULIC COMPANY. ALL RIGHTS RESERVED. iCt8u 11,022 CARBON STEEL PIPE HOLE CUT PRODUCTS 11.02 STYLES 920 AND 920N DIMENSIONS 50- Q Z.D 0 0 0 qm- C 0 fY9 ri V ri.5ea m5'o ' I O T-000-51 ABLE CONTINUED FROM PAGE 2 x 920N 150 3.03 3.56 - 259 7W 2.75 3.7 - / ), a 9 ON oo u 300 3 269 701 27 7 -- - 20 3450 331 76 90 - - 58 178 70 18 (a) u 9ON 500 1.50 2.88 3.56 2.69 7.01 2.75 3.6 - 25 3450 33.1 73 90 - 58 178 70 1,8 GROOVED OUTLET 1¼ (a) 920 500 1.75 3.08 3.78 4,00 2.69 7.01 3.00 40 3.5 32(b) N 3450 44.5 78 96 102 58 78 76 1.9 .8 1½1a) 920 500 2,00 - 3.28 4.00 4.00 2,69 7,01 3.25 4.2 3.9 40(b) N 3450 50.8 83 102 102 68 178 83 2.0 1.9 2 (a) Ye 500 2.50 3.25 4.00 4.00 2.69 7.01 3.88 5.0 4.6 110 92015 340 63.5 83 102 102 68 178 99 2.3 2.1 2k (a) 920 500 2,75 188 400 400 2.69 7.34 4,63 38 50 - 65 3450 69.9 73 102 102 68 186 118 2.5 2,3 751 92 5002752.88 4002,697,34 4.63 6.4 . me 3450 , 69.9 73 - 102 68 186 , 118 - 2.9 3(a) t 5aO 350 331 4 0 4J2 269 773 12 84 64 80 920 3453 88.9 84 114 105 58 195 130 3.8 2.9 FEMALE THREADED OUTLET , - .. 1 . 1 90N 500 1.75 3.08 3.7a 2.63 7,64 3.05 5.0 32 3450 44.5 78 96 67 194 78 2.3 1/2)4)5 - 5002.00 3.28 4,00 2,63 7.64 3.25 5,0 Provides a direct branch connection at 40 92I'1 3450 503 83 102 - 57 19 83 2.3 any location where a hole can be cut 2(a) 9205: 500 ' 2.50 3.25 4.00 2,63 7,64 4.00 4.0 in the pipe ...52_ . ' 3450 63.5 133 , 102 67 194 , 102 1.9 - 76 0 500 2.75 2.88 4.00 4,00 2.63 7.64 4.29 8.0 7.8 A pressure responsive gasket provides 3450 69.9 73 102 * 102 67 - 194 109 , 3.5 3.5 the seal 3(a) 920 ' ' 3.50 3,31 4/23 4.50 2.63 763 4.88 6.8 6.5 80 3450 839 84 14 114 , 194 1 4 3,1 3.0 Request Publication 1103 for s i,' '..l 920 533 200 403 475 475 16 970 69 74 76 Mechanical-I cross assemblies 125 54Q .........3450 50.8 102121 - 121 80 246 , 94 - 3.4 3. 2)a)f 9.0 500 250 4.00 475 4.75 3,16 970 4.38 8.2 8.0 Pressure rated up to 500 psi/3450kPa 3450 63.5 102 121 121 80 246 11' 3.7 3.5 on steel pipe; also available for use 2½ (a) 3 920 500 2.75 363 4,75 4.75 315 9.70 4.63 8.3 7.9 with HDPE pipe 55 3453 69.9 92 -. 121 121 80 246 118 3.8 3/2 7' rem a, 920 500 2.75 3.75 4,75 316 9.70 4.63 - 8.0 Sizes from 2 x ½/SO x 15mm 34A1 699 95 12 80 - 46 118 36 through 8 x 4/200 x 100mm 3(a) 3 920 500 3.50 3,81 5.00 4.63 116 9.70 5.31 8,4 8.8 80 , 3450 83.9 97 127 118 80 246 135 3/2 4,0 50 2 500 2,50 3,75 4.50 317 8.00 3.88 8.0 133.0 .r 9204 3450 63.5 95 114 - 81 203 99 3.6 - 500 3.50 3.81 5.00 3.00 9.46 5.31 8.0 80 20 3450 88.9 97 127 76 240 135 3.6 - TABLE CONTINUED ON PG. 4 IMPORTANT NOTES: Center of run to engaged pipe end, female threaded outlet only (dimensions approximate). Style 920 and Style 920N housings cannot be 3 Available with grooved or female threaded outlet. Specify choice on order, mated to one another , Center of run to end of fitting. to achieve cross connections, 8 Female threaded outlets are available to NPT and BSPT specifications. See page 7 for -ire Protection approvals and pressure ratings, (a) British Standard female pipe threaded outlet is available as listed. Specify "BSPT" clearly on order. (b)For 76.1 mm threaded outlet, specify 21/2" BSPT clearly on order. § Vds approved f@r fire protection services a LPCB approved for fire protection services 0 Approved for use in China by Tianjin Approvals Company. wwwvictauJiccom ictoulicr VICTAULIC IS REGISTERED TRADEMARK OF VICTAULIC COMPANY 2017 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 11102.3 CARBON STEEL PIPE - HOLE CUT PRODUCTS 11.02 Mechanical-r Bolted Branch Outlets STYLES 920 AND 920N DIMENSIONS 9o3 W Ie?'w r'o3 1F4 J)7 "4"e 1 4'-3' , * V -Z---- 2_''_,L._'a Z4 TABLE CONTINUEDFROMPAGE3 V 139.7 1 ½ t 920N 500 200 3 78 4.50 330 8.23 3.25 7.0 - lx 40 3450 50.8 96 114 - a's 209 - 83 3.2 2t 920N 500 2.50 3.75 4.50 3.30 8.23 3.88 9.0 - -- - 50 3450 63.5 95 114 - 84 209 99 4.1 W 6 1 '4(a) 500 1.75 4.43 5,13 5,13 3.79 9.15 3.25 5.1 4.8 150 ' 32(b) 920½ 3450 44.5 112 130 130 96 232 83 2.3 2.2 GROOVED OUTLET 1½ (a) t 9212N 500 2.00 4.40 5.13 5.13 3.79 9.15 3.25 5.4 5.1 40(b) 3450 50.8 112 130 130 96 232 83 2.4 2.3 2(a) ta 500 2.50 4.38 5.13 5,13 3.79 9.15 3.88 6,0 5.6 50 9201 3450 63.5 111 130 130 96 232 99 2.7 2,5 4 V b . 21/2 20 500 2.75 4.01 5.13 5.12 3.69 10.51 4.63 8.3 7.6 65 , 3450 69.9 110 130 130 94 267 118 3.8 3.4 V 761 920 500 2.75 4.15 ' 5.21 3.69 0.51 4.63 8.4 T . 3450 69.9 105 - 32 94 267 118 - 3.8 - 3)a(t 920 500 3.50 4.31 5.50 5.13 3.69 10,51 5.31 9.9 8,4 w 80 3450 88.9110140 130 94267 135 4.5 3,8 4(a)ts 920 500 450 381 515 538 369 051 625 10 101 100 3450 114.3 97 146 137 94 267 159 4.6 4.6 FEMALE THREADED OUTLET . - - - - . . I ½ (a) , 500 2.00 4.41 5., 3 .63 9.40 3.25 7.8 - L9.0 x 40 920½ 3450 50.8 112 130 - 92 239 83 3.5 2 500 2,50 4,38 5.13 3.63 9.40 3.88 8.0 - WON Provides a direct branch connection at so 3450 63.5 111 130 - 92 239 99 3.6 - any location where a hole can be cut 76.1 mm, 920 ' 500 2.75 4.38 5,50 5.13 3.63 9.40 ' 4.63 ' 9.5 9.5 in the pipe _______ 3450 69.9 - 111 140 130 92 239 118 4.3 4.3 A pressure responsive gasket provides 920 500 350 431 550 513 3.63 9,40 531 8' 14,0 3450_889 10 140 30 92 239 135 37 6.4 the seal 108.0mm 920 500 4.50 4.45 5.38 3,63 9.40 6.12 10,0 3450 114.3 113 137 92 239 155 4.5 Request Publication 11.03 for ' ___ 500 4.50 3.31 5.75 3.63 9.40 6,25 18.0 Mechanical-I cross assemblies 100 _3450114.396.80146-922391598.2 - TABLE CONTINUED ON PG. 5 Pressure rated up to 500 psi/3450 kPa Center of run to engaged pipe end, female threaded outlet only (dimensions approximate). on steel pipe; also available for use t Available with grooved or female threaded outlet. Specify choice on order. with HOPE pipe * Center of run to end of fitting, Sizes from 2 x ½/SO x 15 mm 4 Female threaded outlets are available to NPT and BSPT specifications, through 8 x 47200 x 100 mm @ See page 7 for Fire Protection approvals and pressure ratings. (a) British Standard female pipe threaded outlet is available as listed, Specify "BSPT" clearly on order. (b)For 76.1 mm threaded outlet, specify 2/2" BSPT clearly on order. § Vds approved for fire protection services o :!-PCB approved for fire protection services IMPORTANT NOTES; 0 Approved for use in China by Tianjin Approvals Company, Style 920 and Style 920N housings cannot be mated to one another to achieve cross connections, www.victauIiccom ctauI.c VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 0 2057 0CTAuUC COMPANY. ALL RIGHTS RESE8VED, 11424 REV4 FEMALE THREADED OUTLET Provides a direct branch connection at any location where a hole can be cut in the pipe A pressure responsive gasket provides the seal Request Publication 11.03 for Mechanical-T cross assemblies Pressure rated up to 500 psi/34S0kPa on steel pipe; also available for use with HDPE pipe Sizes from 2 x ½/SO x 15mm through 8 x 4/200 x 100mm CARBON STEEL PIPE - HOLE CUT PRODUCTS 11.02 VechanicalT® Bolted Branch Outlets STYLES 920 AND 920N DIMENSIONS 9.10 0 ? ie0 (Li 0 '! t9 fie n-m f*'41 ra'" raa 9flTh 4 Ilk 165.1 >1 9/04 500 1,50 3.88 4,56 3.79 9.34 2.75 8.0 25 3450 38.1 99 116 - 96 237 70 3.6 - 1 920N 500 1.75 4.43 5.13 3.79 9,34 325 8.4 32 3450 44.5 113 130 - 96 237 83 3.8 11/2(a)tk 90N 500 2.130 4.41 5.13 5.13 3.79 9.34 3.25 - 8.4 5.4 40 3450 50.8 112 130 130 96 237 83 3.8 2.4 2(a) 't 920N 500 2.50 4.38 5,13 5.13 3.79 9.34 3.88 8.5 6,0 50 3450 63.5 111 130 130 96 237 99 3.9 2.7 761 mm 920 500 2.75 - 4.01 5.13 5.21 3.63 10.51 - 4.63 8.6 7.6 3450 69.9 110 130 132 92 267 118 3.9 3.4 3 ta) (c 920 500 - 3.50 ' 4.31 5.50 5.13 3.63 10.51 5.31 10,2 8.4 80 , 3450 889 110 140 130 92 , 267 135 4.6 , 3.8 4 (a) ta 920 500 4.50 3.81 5.75 5.38 3.63 10.51 ' 6.25 105 8.4 180 3450 114.3 97 146 137 92 267 159 4.8 3.8 8 2(a)t 92 500 2.75 5.44 6,19 6.25 4.81 12,42 4.50 11.6 - 11.6 200 50 3450 69.9 138 157 159 122 316 114 5.3 - 5.3 25(a)t 920 00 275 507 619 6.19 48 1242 450 16 11.6 65 3450 69,9 129 157 157 122 316 114 5,3 53 mm. 761 ' 90 2 500 z,75 5.25 6.25 4.81 12.42 4.56 11.6 3450 69.9 133 - 159 122 316 116 - 5.3 jl'll 920 50 3,50 531 650 650 48 1242 531 26 1 86 3450 88.9 135 165 165 122 316 135 , 5.7 , 5.3 4(a) 1'a 920 500 4.50 4.81 6.75 6.38 ' 4.81 12.42 6.25 ' 15.3 ' 12.5 100 3450 1143 122 171 162 122 316 159 6.9 5.7 * Center of run to engaged pipe end, female threaded outlet only (dimensions approximate). 1' Available with grooved or female threaded outlet, Specify choice on order. t Center of run to end of fitting. # Female threaded outlets are available to NPT and BSPT specifications. @ See page 7 for Fire Protection approvals and pressure ratings: (a) British Standard female pipe threaded outlet is available as listed. Specify "BSPT' clearly on order, (b) For 76,1 mm threaded outlet, specify 21/2 BSPT clearly on order § Vds approved for fire protection services o LPCB approved for fire protection services 0 Approved for use in China by Tianjin Approvals Company. IMPORTANT NOTES: Style 920 and Style 920N housings cannot be mated to each other to achieve cross connections. www.vlctauflc.com AstauIic vlcTAuuC IS A REGISTERED TRADEMARK OF VIcTAIJLIC COMPANY. 0 2017 VICTAULIC COMPANY. ALL P1131-ITS RESERVED. REV U 11102,5 CARBON STEEL PIPE HOLE CUT PRODUCTS 11.02 Mechanical-i® Bolted Branch Outlets STYLES 920 AND 920N FLOW DATA Flow test data has shown that the total head loss between point (1) and (2) for the Style 920, 920N and 929 Mechanical-T fittings can best be expressed in terms of the pressure difference across the inlet and branch. The pressure difference can be obtained from the relationship below. C, and Ky Values Values for flow of water at +0°F/+1 °C are shown in the table below. Exaggerated for clarity Hazen-Williams coeffident of friction is 120, Pipe with a wall thickness of 0.l65inJ42mm. 1" FireLock Innovative Groove System (IGS) outiet Formulas for c,1iç Values: AP = Q = C x Where: -Q, Where: O = Flow (GPM) — 0 = Flow (m3/hr) K 2 LP = Pressure Drop (psi) AP = Pressure Drop (Bar) C = Flow Coefficient Q = K x JAP K = Flow Coefficient www.vlctauhc.com JttauIic' ViCTAuLiC IS A REGISTERED TRADEMARK OF vICTAuLiC COMPANY. © 2017 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 11.026 Re/fl CARBON STEEL PIPE - HOLE CUT PRODUCTS 11.02 MechanicalT® Bolted Branch Outlets STYLES 920 AND 920N FIRE PROTECTION APPROVALS AND PRESSURE RATINGS The information provided below is based on the latest listing and approval data at the time of publication. Listings/Approvals are subject to change and/or additions by the approvals agencies. Contact Victaulic for performance on other pipe and the latest listings and approvals. u/I) 0ST5" 22 =. 21/2-6 2,875-6625 40 10,40 400 400 400 290 232 362 65-153 73,0- 168.3 2.875 - 4.500 All OF ' 2755 300 2755 300 2755 300 - 1999 290 1599 232 2496 362 21/2-4 65-100 73.0-114.3 2V5 - 4.500 All - 2065 300 2065 300 2065 300 1999 290 1599 232 2496 362 21/2-4 65-100 730- 114.3 6,625 34 10 2065 300 2065 30,3 2065 250 1999 290 1599 232 2496 - 362 6 150 168.3 6.625 ' 3040 2065 300 2065 ' 300 1724 300 1999 290 1599 - 232 2496 362 6 150 168.3 8,625 ' 21/2 ' 10,40 2065 400 2065 ' - 2065 . - 1999 - 1599 - 145 2496 8 200 219,1 8.625 ' 34 ' - 10 2755 300 , - 250 - 1000 145 - B 200 219.1 - 8625 ' 34 30,40 - 2065 300 - - 1724 300 - 1000 145 - 8 200 219.1 ' 2065 2065 1000 NOTES; 10 refers to Listed/Approved Schedule 10 steel sprinkler pipe. 40 refers to Listed/Approved Schedule 40 steel sprinkler pipe, DF refers to Listed/Approved Dyne-Flow steel sprinkler pipe manufactured by American Tube Company. SF refers to Listed/Approved Super-Flo steel sprinkler pipe manufactured by Allied Tube and Conduit Corporation VIC-TAP II HOLE CUTTING TOOL FOR The Vic-Tap II hole cutting tool is designed for use with the Style 931 Vic-Tap II Mechanical-T unit, 4 - 8/100 - 200 MM CARBON STEEL PIPE which is a combination of the Style 920 Mechanical-T and Series 726 Vic-Ball Valve. The Vic-Tap II is capable of tapping into carbon steel pipe systems under pressures up to 500 psi/345OkPa. The Style 931 Vic-Tap II Mechanical-T unit is a full port ball valve which can be mounted on 4?100mm, 57125 mm, 6/150mm and 87200 mm diameter pipe. The Style 931 comes with a 2½"/65mm grooved outlet. The drill motor is an electric motor with ground fault circuit interrupter (GFCI) in accordance with safety codes. For more information, refer to publication 24.01, www.victauUc.com ictsube VICTAtJLIC I S A REGISTERED TRADEMARK OF vICTAIJuC COMPANY 02017 vicrAuLIc COMPANY. ALL 9(01-ITS RESERVED. REV N 11,02 7 VechanicaI1 STYLES 920 AND 920N INSTALLATION Reference should always be made to the 1-100 Victaulic Field Installation Handbook for the product you are installing. Handbooks are included with each shipment of Victaulic products for complete installation and assembly data, and are available in PDF format on our website at www.victauliccom, WARRANTY Refer to the Warranty section of the current Price List or contact Victaulic for details, NOTE This product shall be manufactured by Victaulic or to Victaulic specifications. All products to be installed in accordance with current Victaulic installation/assembly instructions, Victaulic reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations. For complete contact information, visit www.victaulic.com 1102 1480 REV UPDATED 12/2017 vIcTAuuc IS A REGISTERED TRADEMARK OF VICTAUUC COMPANY. © 2017 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 11,02 L FireLock0 STYLE 922 The Style 922 Outlet-T provides a convenient method of incorporating ½, 3/4, and 1/15, 20 and 25mm outlets for directly connecting sprinklers, drop nipples, sprigs, gauges, drains and other outlet products. Available for 11/4 through 76.1 mm/32 to 76.1 mm piping systems, Style 922 outlets are UL/ULC Listed, LPCB and FM Approved for branch connections and VdS Approved for direct sprinkler connection only on wet and dry systems. The locating collar engages into the hole prepared in the pipe. When tightened, the assembly compresses the gasket onto the OD of the pipe. The Style 922 Outlet-T is UL/FM rated up to 300 psi/2068 kPa and VdS rated up to 16 bar at the ambient temperatures typical for fire protection systems. Style 922 is suitable for use on standard, lightwall, Schedule 5 and other specialty pipes.* Contact Victaulic for other optional coatings. *Consult Section 10.01 for specific listings/approvals MATERIAL SPECIFICATIONS Housing: Ductile iron conforming to ASTM A-536, grade 65-45-12. Ductile iron conforming to ASTM A-395, grade 65-45-15, is available upon special request. Gasket: Grade "E" EPDM - Type A (Violet color code). FireLock products have been Listed by Underwriters Laboratories Inc. and Approved by Factory Mutual Research for wet and dry (oil free air) sprinkler services up to the rated working pressure using the Grade "E" Type A Gasket System. Bolts/Nuts: Heat-treated plated carbon steel, trackhead meeting the physical and chemical requirements of ASTM A-449 and physical requirements of ASTM A-183. Housing Coating: Orange enamel (North America, Latin America, Asia Pacific) Red enamel (Europe) JOB/OWNER CONTRACTOR ENGINEER System No. Submitted By Spec Sect Pa ra___________ Location Date Approved www.victaulic.com vicTAuLic IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 0 2009 vICTAuLIC COMPANY. ALL RIGHTS RESERVED. gfv G 4tauiicr 10,521 IPS CARBON STEEL. PIPE - HOLE CUT PRODUCTS 10.52 FireLock Outleti STYLE 922 DIMENSIONS aaci (1 11/4 ½ 1 3A 1.30 1.83 1.10 3.87 2.56 1.0 v 1 32 15 30.2 33.0 - 46.5 27.9 98.3 65.0 0.45 3/4 1 3/3 1.28 1.83 1.10 3.87 2.56 1.1 - - - - - - - , 20 30.2 32.5 46.5 27.9 98.3 65.0 0.50 W 1 13A6 1.52 2.18 1.10 - 3.87 2.56 1.2 25 30.2 38.6 55.4 27.9 98.3 - 65.0 0.54 11/2 x ½ 13A6 1.42 1.95 1.22 4.08 2.56 1.2 40 15 30.2 36.1 49.5 31.0 103.6 65.0 0.54 Y4 13A6 1.40 1.95 1.22 4.08 2.56 1.2 20 30.2 35.6 49.5 31.0 103.6 65.0 0.54 1 13A6 1.64 2.30 1.22 4.08 2.56 1.3 25 302 41.7 58.4 31.0 1036 650 0.59 2 x 1/2 1/16 1.66 2.19 1.46 4.60 2.56 1.3 50 15 30.2 42.2 55.6 37.1 116.8 65.0 0.59 3/4 1/16 1.64 2.19 1.46 4.60 2.56 1.4 20 30.2 41.7 55.6 37.1 116.8 65.0 0.64 1 13/16 1.88 2.54 1.46 4.60 2.56 1.5 25 30.2 47.8 64.5 37.1 116.8 65.0 0.68 2½ x 1/2 13A6 - 1.91 2.44 1.71 5.40 2.56 1.6 65 15 30.2 48.5 62.0 43.4 137.2 65.0 0.73 Y~ ' 13A6 1.89 2.44 1.71 5.40 2.56 1.6 20 30.2 48.0 62.0 43.4 137.2 65.0 0.73 1 1 3/16 2.13 2.79 1.71 5.40 2.56 1.6 25 30.2 54.1 70.9 43.4 137.2 65.0 0.73 ½ 13/16 1.91 2.44 1.71 550 2.56 1.6 76.1 mm X 15 30.2 48.5 62.0 43.4 139.7 65.0 0.73 3/4 13A6 1.89 244 1.71 5.50 2.56 1.6 20 30.2 48.0 62.0 43.4 139.7 - 65.0 0.73 1 1 3A6 2.13 2.79 1.71 5.50 2.56 13 25 30.2 54.1 70.9 43.4 139.7 65.0 0.80 t Victaulic female threaded products are designed to accommodate standard NPT or BSPT (optional) male pipe threads only. Use of male threaded products with special features, such as probes, dry pen- dent sprinklers, etc., should be verified as suitable for use with this Victaulic product. Failure to verify suitability in advance may result in assembly problems or leakage. *Center of run to engaged pipe end for NPT threads (dimensions are approximate). www.victaulic.com ictaulid vIcTAuLIC IS REGISTERED TRADEMARK OF vicTAuLic COMPANY. © 2009 vIcTAuLIC COMPANY. ALL RIGHTS RESERVED. 10,52 .2 REV. G IFS CARBON STEEL PIPE HOLE CUT PRODUCTS 10.52 FireLock0 Outlet-I STYLE 922 PERFORMANCE Hazen-Williams coefficient of friction is 120 www.victaulic.com ctauI.c VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 0 2009 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REV Co 1O523 FireLock® STYLE 922 INSTALLATION Reference should always be made to the 1-100 Victaulic Field Installation Handbook for the product you are installing. Handbooks are included with each shipment of Victaulic products for complete installation and assembly data, and are available in PDF format on our website at www.victaulic.com. WARRANTY Refer to the Warranty section of the current Price List or contact Victaulic for details. NOTE This product shall be manufactured by Victaulic or to Victaulic specifications. All products to be installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations. For complete contact information, visit www.victaulic.com 10.52 3355 REV G UPDATED 12/2009 VA Jtauhcf VICTAIJLIC IS REGISTERED TRADEMARK OF vlcrAuLic COMPANY. © 2009 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 10.52 Ductile Iron Threaded Fittings SMITH,COOPER~ Ductile Iron Threaded Fittings Specifications branded ductile iron threaded fittings are UL Listed and FM Approved at 500 psi Rated to 300 WSP U Ductile iron castings conform to ASTM A536 C L us LISTED Fitting dimensions conform to ASME B16.3 Bushings and plugs conform to ASME B16.14 Fittings are 100% air tested APPROVED NPT threads on all fittings conform to ASME 13I.20,1 Independent lab verification that fittings meet applicable chemical & physical properties Manufacturing facilities are ISO 9001:2008 and ISO 14001 Temperature Degrees F Working Pressure, Nonshock psiG 300# Class Threaded Fittings -20 to 100 500 150 - -- 500 200 480 250 460 300 440 350 420 400 400 450 380 - 500 360 550 340 600 320 650 - 300 c®us APPROV ~FM Fig. 35E 3_900 Elbow LISTED Size in Part Number A in Packing Weight lb Inner Master 1/2 35E 3004 1.13 100 200 0.2 3/4 35E 3006 35E 3010 1.31 1.50 70 140 80 0.3 1 40 0.5 1-1/4 1-1/2 - 35E 3012 35E3014 1.75 1.94 25 50 36 0.8 18 1.1 2 HE 3020 2.25 10 20 -. 1.8 2-1/2 35E 3024 2.70 4 1 8 3.2 Size in Part Number A in B in Packing Weight .lb Inner Master 3/4 x 1/2 35RE3006004 1.20 1.22 60 160 0.3 1 x 1/2 35RE3010004 35RE3010006 1.26 1.36 70 140 OA 1x3/4 1.38 1.45 50 100 0.4 1-1/4 x 1/2 35RE3012004 , 35RE3012006 - 1.34 1.45 1.53 35 35 70 0,5 1-1/4x3/4 1.63 70 0,6 1-1/4x1 1-1/2x 1/2 35RE3012010 1.58 1.52 1.67 30 60 60 0.7 0.6 35RE3014004 1.75 30 1-1/2x3/4 35RE3014006 35RE301 4010 1.52 1.75 1.80 25 20 50 40 0.7 1-1/2 x 1 1.65 0.8 1-1/2 x 1-1/4 35RE3014012 1.82 1.88 1,97 18 36 1.0 1.0 2x1/2 35RE3020004 1,60 18 36 2x314 2x1 - 35RE3020006 35RE3020010 1.60 1.73 1.97 18 36 1.0 2.02 16 32 1.2 2x 1-1/4 35RE3020012 1,90 2.02 2.10 12 24 1.3 2x1-1/2 35RE3020014 2.16 10 20 1.5 2-17x 1-1/2 35RE3024014 2.16 2,51 6 12 2.2 2-1/2x2 - 35RE3024020 2,39 2.60 6 12 2.5 Fir. 35F 3-45° Elbow Size in Part Number a U er A in Packing Weight lb Inner Master 1/2 35F 3004 0.88 150 300 0.2 3/4 - 35F 3006 - 0.98 80 160 0.3 1 35F 3010 1.13 40 80 0.5 1-1/4 35F3012 1,29 25 50 0.7 1-1/2 35F 3014 1,44 20 40 1.0 2 35F 3020 1.69 10 11 20 1,6 2-112 35F 3024 1,95 4 8 2.7 Fig. 35RE3 - 90° Reducing Elbow Fig. 35T 3- Tee Size in Part Number A in Packing Weight lb Inner Master 1/2 35T3004 1,13 80 160 0.3 3/4 35T3006 1.31 30 60 - 0.5 1 35T3010 1.50 25 50 0.7 1-1/4 35T3012 1.75 10 20 1 1.1 1-1/2 3573014 1.94 10 20 1.5 2 35T 3020 2.25 6 12 24 2-1/2 3513024 2,70 4 8 4,3 111 SMiTH-COOPER 1NTERNATIONAL • TOLL FREE I-800-766-0076 9 FAX (323) 890-4456 9 ww%csmithtoopr.com Size in Part Number .in A B in C in Packing Weight lb inner Master 3/4x 1/2 1 x 1/2 1x1/2x1 35R13006004 120 120 1.26 1.36 1.38 1.31 122 1.36 1.50 60 30 30 25 , 35 120 60 60 0.4 0.6 0,6 . 0.6 0.6 35R13010004 35RT3010004010 1.26 1.50 * 1 x3/4 1 x3/4x3/4 1x3/4x1 1-1/4x1/2 35RT3010006 35R13010006006 1.38 1.38 1,45 1.45 50 70 358T3010006010 35R73012004 1.50 1.34 1.45 1.34 . 1.50 1.53 25 20 50 40 07 0.8 1-1/4x 112x 1-1/4 1-1/43/4 35813012004012 35813012006 1.75 1.45 1.53 1.45 1.75 1.62 25 15 ' 50 30 0.9 0.9 1-1/4x3/4x1-1/4 1-1/4x1 358T3012006012 1.75 1.58 1.62 1.58 1.75 1.67 20 15 40 30 50 40 1.0 1.0 35813012010 1-1/4 x x 1/2 1-1/4x1x3/4 35813012010004 35R13012010006 1.34 1.45 1.26 1.53 25 20 0.7 0.8 1.38 1.63 1-1/4x1x1 1-1/4 X lx 1-1/4 1-1/2x1/2 35R13012010010 35RT3012010012 1.58 1.50 1.69 20 15 40 30 -or 1.0 1.75 1.69 1.75 ' 35RT3014004 1.41 1.81 1.41 1.66 1.88 1.9412 16 24 32 48 1.0 1.1 1-1/2x1/2x1-1/4 35R13014004012 1.56 1-1/2x1/2x1-1/2 35RT3014004014 1.94 1.66 24 1.2 1-1/2x3/4 358T3014006 1.52 1.52 1.75 16 32 5 1.1 1-112X3/4X1-1/4 1-1/2x3/4x1-1/2 35813014006012 35RT3014010 , 1.94 1.66 1.88 ' 18 1.1 358T3014006014 1.94 1.75 1.94 36 1.2 1-1/2x1 11/2xlx1/2 35R13014010004 1.65 1.44 1.65 1.25 1.80 1.69 12 20 24 40 1.2 0.8 1-1/2x1x3/4 35RT3014010006 35RT3014010010 1.50 1.44 1.50 1.80 16 16 32 0.9 1.65 32 1.0 1-1/2x1x1-1/4 1-1/2xlx1-1/2 35RT3014010012 358T3014010014 1.82 1.67 1,80 - 1.88 1,94 , 12 12 24 1.2 1,94 24 1.3 1-1/2x1-1/4 l-1/2x1-1/4x1/2 35R73014012 1.82 1.82 1.88 12 , 24 1.4 - 35813014012004 1.41 1.34 1.66 16 32 0.9 1-1/2x1-1/4 x3/4 358T3014012006 1.52 1.65 1.45 1.58 1.75 1.80 16 32 1.0 1-1/2x1-1/4x1 35R13014012010 16 32 1.1 1-1f2x1-1/4x1-1/435813014012012 1.82 ' 1.75 1.88 ' 14 14 28 1.3 1-1/2x1-1/4x1-1/2 35813014012014 1.94 1.88 1.94 28 1.4 2x1/2 358T3020004 1.49 1.60 1.49 1.88 10 20 1.5 1.6 2x3/4 35813020006 1.60 1.97 10 20 2x1 35R13020010 1.73 , 1.90 1.73 2.02 8 16 1.7 2x1x2 - 35RT3020010020 2.25 2.02 2.25 B 16 1.9 2x1-1/4 358T3020012 1.90 2.10 8 16 1.9 2x1-1/4x2 358T3020012020 2.25 2.10 2.25 8 16 2.0 2x1-1/2 2x 1-1/2x3/4 , 35813020014 2.02 2.16 8 16 2.1 2x1-1/2x1/2 35R13020014004 1.49 1.41 1.88 10 20 1.3 35RT3020014006 35813020014010 1.60 1.73 1.52 1.97 10 20 1.4 2x1-1/2x1 1.65 2.02 8 16 1.5 2x1-1/2x1-1/4 358T3020014012 1.90 2.02 1.82 2.10 , 8 8 16 16 1.7 1.8 2x1-1/2 x1-1/2 1 35RT3020014WA 1.94 2.16 'Jill I C®uS APPROVW Fig. 35RT3 - Reducing Tee LISTED Fig. 35BT3 - Bull Head Tee Size in Part Number A in , B in C in Weight lb Inner 3/4x1 35913006010 1.45 1.45 1.37 30 Pac t40 0.6 1x1-1/4 35BT3010012 1.67 1.67 1.58 20 0.9 1 x1-1/2 35813010014 1.80 1.80 1.65 15 1.0 1-1/4x1x1-1/2 35813012010014 1.88 1.88 1.80 ' 1.82 1,62 ' 15 15 30 1.2 1-1/4x1-1/2 35913012014 1,98 30 1.3 1-14x2 35B13012020 2.10 2.10 1.90 10 20 1.6 1-1/2 x1-1/4x2 35813014012020 2.16 2.10 2.02 10 20 1.8 1-112x2 1 358T3014020 2,16 2.16 2.02 8 16 1.8 SMITH-COOPER INTERNATIONAL' • TOLL FREE I-800-716-0076 • FAX (323) 890-446 • www.smithcooper.com 112 Fig. 35CP3 - Straight Coupling with Ribs c®uS >FM APPROM LISTED Size in Part Number I in A Packing Weight lb inner Master 1/2 3/4 1 35CP3004 350P3006 1.38 200 400 0.1 1.63 100 200 120 0.2 0.4 35CP3010 1.75 60 1-1/4 1-1/2 35CP3012 35CP3014 2.00 35 70 0.5 0.7 2.19 25 50 2 35CP3020 2.62 15 30 1.2 2-1/2 35CP3024 3.00 1 9 18 2.2 Size in Part Numbe r A in - Packing Weight lb Inner Master 1 x 1/2 35HB3010004 1.06 180 360 0.2 lx 3/4 1-1/4 x1 35H83010006 35HB3012010 1.06 180 360 0.1 1.19 90 180 0.2 1-1/2x1 1-1/2x1-1/4 35HB3014010 35HB3014012 1.25 75 150 0.4 1.25 75 150 0.3 2 x 1 3B3020010 1.38 40 - 80 -- 80 0 0.6 2x 1-1/4 35HB3020012 1.38 40 2x1-1/2 35HB3020014 1.38 40 80 0.6 Fig. 355P3 - Square Head Plug I Size in Part Number I in Packing - Weight lb Inner Master I 1/2 35SP3004 0.94 600 1200 0.07 I4 35SP3006 1.12 350 700 0.1 I 35SP3010 1.25 200 400 0.1 1-1/4 35SP3012 1.37 100 200 0.3 1:1/2 35SP3014 1.44 80 160 0.4 35SP3020 1.50 45 90 0.6 Fig. 35RC3 - Hex Reducing Coupling Size in Part Number A in Packing Weight lb Inner Master I x1/2 35RC3010004 1.89 80 160 120 0.3 1 x 3/4 1-1/4x3/4 35RC3010006 35RC3012006 1.69 60 0.4 2.06 40 80 0.6 2x 1 (not hex) 35RC3020010 - 2,81 1--TO- 40 1.0 Fig. 35HB3 - Hex Bushing Fig. 35U 3- Union with Brass Seat Size in Part Number A in Packing Weight lb Inner Master 1 35U 3010 2.19 20 40 1.0 1-1/4 33012 2.50 15 30 1.2 1-1/2 35U k147 2.62 10 20 1.7 2 35U 3020 1 3.12 " 12 1 2.4 113 WITH-COOPER INTERNATIONAL® 9 TOLL FREE I-800766-0076 0 FAX (323) 90-4436 0 wwsmhcooper.com c®us ? APPRO LISTED Size Part Number m A in Packing Weight lb inner Master 1 35X3010 35X 3012 1.50 1.75 1.94 20 12 8 40 24 16 0.9 1,4 1.8 1-1/4 1-1/2 2 35X3014 33020 2.25 6 12 1 2.8 A Fig. 35X 3- Cross Size in Part Number - in Packing Weight lb Inner Master 1/2 3503004 087 300 600 200 400 0.1 3/4 3503006 0.97 0,1 1 3503010 1.16 110 220 0.2 1-1/4 -1-1/2 35C 3012 1 28 - 70 140 - 100 04 35C 3014 1.33 50 0.5 2 3503020 1.45 25 50 0.8 2-1/2 35C 3024 1.70 - 18 36 1.6 Fig. 332C3 - Hewn Clamp ID Fig 35RX3 - Reducing Cross Size in r Part N mb Nu or A in B in Packing Weight lb Inner Master 1-1/4 x1 35RX3012010 1.67 158 15 30 1.2 1-1/2x1 2x 1 35RX3014010 35RX3020010 1.80 165 12 24 16 14 2.0 2.02 1.73 8 Fig. 35C3-Cap Size in Part Number A in Packing Weight lb I Inner Master 3/8 35803003 1 0.75 100 200 0.3 1/2 35803004 0.75 80 160 0.5 SMITH-COOPER INTERNATIONAL® 9 TOLL FREE 1-800-766-0076 • FAX (323) 890-446 to www.smithooper.con 114 r Vu III2 :rFI1 0141VIIVI JrO 2012 PRODUCT CATALOG www.itwbuildex.com 800-BUILDEX w — w w w w_w_w W V ww&w*w W WWW • - I_I tw 4;gww V V V A M WON Y -,- ta A 0 k - -:--- if ° : TABLE OF CONTENTS SammyO for Wood . 4 Sidewinder for Wood . 5 Sammys Swivel Head for Wood ....................................................................................... ............... 5 Sammys® for Steel ........................................................ .................................................................... 6 SidewinderOfor Steel........................................................................................................................7 Sammys Swivel Head for Steel.......................................................................................................7 SammyX-Press ...............................................................................................................................8 SammyX-Press Sidewinder ............................................................................................................8 SammyX-Press SwivelT ...................................................................................................................9 Sammy X-Press It® lnstaIlaon Tool ........................... ......................... .............................................. 9 Sammys® for Concrete...................................................................................................................10 Sidewinder® for Concrete................................................................................................................10 Sammys Swivel HeaV for Concrete................................................................................................11 Concrete/Wood Installation Kit........................................................................................................11 SammysToggle ............................................................................................................................12 CeilingScrews.................................................................................................................................12 Dektite® Pipe Flashing.....................................................................................................................13 SpeedyPole Tool TM..........................................................................................................................13 SpotRite Level ..............................................................................................................................13 Approvalsand Listings....................................................................................................................14 SpecialNotes..................................................................................................................................15 Warranty • Disclaimer of Warranty Proper fastener connection design takes in to account where and how fasteners are used. Allowance for special characteristics in materials, differences in materials, differences in types of materials being joined, unique or unusual environmental service or installation conditions and the safety factors required by anticipating normal or short term loading conditions must be considered. Due to possible differences in specifications, applications, and interpretation of results, purchasers and specifiers must make their own evaluation of the products, to determine the suitability of these products for intended use. All warranties of Buildex products, expressed or Implied, including the warranties of merchantabilty and fitness for particular purposes are specifically excluded except for the following: Buildex will repair or replace any product which, within twelve months after sate by Buildex or its distributors, is found by Buildex to be defective in material or workmanship. normal wear and tear accepted. This is the sole warranty of Buildex and the sole remedy available to distributor or buyer, Buildex shall not be liable for any injury, loss or damage, direct, indirect, or consequential, arising out of the use of, or the inability to use, any Buildex product. INSTALLATION STEPS - WAffiM& INTO WOOD & STEEL 1 FINST-A-L-t7-PION STEPS -NTO WOOD & STEELI I. Insert the appropriate nut driver into a 3/8" or 1/2" portable drill, Insert the SAYMM into the #14 (black) nut driver (p/n 8113910). Drill should be in a vertical position. Push the face of the nut driver tight to the member, 8egin installation when the nut driver spins freely on the SAMMYS, stop drill and remove. 4, The SAMMYS is now ready to receive 1/4' 3/8", 1/2" or metric all thread rod, bolt stock. (The 1/2" requires the #14SWred nut driver) Note: When installing DSTR, follow the above instructions, then add retainer nut and torque to 20 foot lbs. for maximumpullcut in purtin steel. I. Insert the appropriate nut driver into a 3/8" or 1/2" portable drill. Insert the SAMMYS into the #145W(red) nut driver (p/n 8114910). With drill unit in a horizontal position and at a right angle to the structural member, begin Installation. When the nut driver spins freely on the SAMMYS, stop the drill and remove. The unit is now ready to receive 1/4' 3/8", Mb, MB or metric all thread rod or bolt stock, Note: When installing SWDR, follow the above instructions, then add retainer nut and torque to 20 foot lbs, for maximum pullout in purlin steel. "(,4waw.,"&&. Z$5S5Z62ZZ EIl 1 [INSTALLATION STEPS INTO CONCRETE] Using an SOS 250 carbide tip bit or a HEX RECEIVER with a #250 carbide tip bit, pre-drill the concrete member to a depth of 2" with a hammer/rotary hammer drill set on impact mode. After pre-drilling has been completed, install the SLEEVE TOOL over the bit (the bit should remain in the drill), and insert the #14 (black) nut driver (p/n 8113910) into the opposite end (see Vertical Installation note above). Insert the CST screw into the nut driver. Place tip of screw into the pre-drilled hole, turn impact/drill unit to drill mode and begin Insertion. When the nut driver spins freely on the CST screw, installation is complete. Stop and remove drill. The concrete screw is ready to receive 1/4". 3/8", 1/2 or metric all thread rod or bolt stock. (#14S W red nut driver used with 1/2" screw) Note: Use a 1200 maximum RPM drill for installation. Note: Do not install concrete screws while the drill unit is in Impact mode— doing so will destroy the pullout factor of the screw. IiSTALLATION STEPS - _1O]j1iL INTO CONCRETE: Using an SOS 250 carbide tip bit or a HEX RECEIVER with a #250 carbide tip bit, predrill the concrete member to a depth of 2" with a hammer/ rotary hammer drill salon impact mode. After pre-drilling has been completed, install the SLEEVE TOOL over the bit (the bit should remain in the drill), and insert the #I4SW(red) nut driver (p/n 8114910) into the opposite end. Insert the SWC screw into the nut driver 4, Place tip of screw into the pre-drilled hole, turn impact/drill unit to drill mode and begin insertion. When the nut driver spins free on the SWC screw, installation is complete. Stop and remove drill, 5. The SWC screw is ready to receive 1/4", 3/8" or metric all thread rod or bolt stock. Note: Use a 1200 maximum RPM drill for installation. Note: Do not install concrete screws while the drill unit is in impact mode— doing so will destroy the pullout factor of the fastener. ________ LM:MlmlcilAhiliilI1lHiii The nut drivers were designed with a unique spin-off feature which provides a fast and safe installation each time, When the face of the driver comes Into contact with the material you are installing into, continue drilling until nut driver spins free. Installation isWan complete. Warranty requires the use of the appropriate nut driver for installations, SAMMYS® FOR STEEL \ Made wtth TOW self-drilling fasteners no pro-drilling required. Installs Into steel range from 20 gauge - 1/2" thicknesses. Saves time from traditional methods. Reduces installation costs. Quick to install using the Sammys Not Driver with an 18V cordless drill/driver, Aatandard screwgun with a depth sensitive nosepiece should be used to install Teks. For optimal fastener performance, the ecrewt# should be a minimum of 6 amps and have an RPM range of 02500. Manufactured in the U.S.A. -. fl,v4ecdeflttaIiofl a r wwwjtwbulldex.com #148" Nut Driver Pafl # 81i390 - liii' 3024957 DSTR100" 114-20x1"TE1(S3 1510 (20 ga.) 036"-20 ga 3/16" 25 125 1/4 - 8025957 DST 100 1/4-14 x I IF/CS 3 446 )20 ga) 036 20 ga 3116 25 125 1/4" 8026857 OST 150 114-14 x 1-1/2" IF/CS 3 970 (16 ga.) ,636".20 ga 3/16' 25 125 1/4 8027957 DST 260 1/4-14x2"IEKS3 446 (20ga.) .036"-209a 3/16" 25 125 114" 8030957 TEK500 12-24x1.1/2"TEKS5 3125 (3/16") 188".3/16" 1/2" 25 125 3/r 663957 DSTR1 T14-26 x I TEKS3 - 1510 (?0 ga. 1500 - 1475 .036"-20 ga 3/16 25 125 3/8" 8031857 DSTR 1-1/2 12-24 a 1-1/2"TEKS 5 - 1510 (3/16") 1500 1475 .060"-l6ga. 1/2" 25 125 - 3/8" 8039957 - DSTR516" 5/1618x 1-1/4TEKS3 2200 (2095.) 1500 1475 .036"-20ga 3/16" 25 - 125 3/8" 6040957 DST 10 1/4-14x1'TEKS3 446 (20 .036'-20 ga 3/16" 25 125 3/8" 8077925 DST 10-SS 1/4-14 a V'TEKS 3 446 (20 .036"-20 ga 3/16" 25 125 3/8" 8041957 DST 15 1/4-14 a 1-1/2" TEKS 3 446 (20 .036"-20 ga 3/16" 25 125 ;8078925 DST 15-SS 114-14x1-17TEKS3 446 (20 ,036"-20ga3/16" 25125 3/8" 8042857 DST 20 1/4-14x2"TEKS3 446 (20 .036-20 ga 3/16" 25 125 - 3/8" 8044957 0S130 1/4-14x3TEKS3 446 (20 .036"-20 ga 3116" 25125 4J. 4j 3/8'" 8045857 DST 516 5/16.18 a 1-1/4" TEKS 3 1500 (3/16") 1500 1475 .125".1/8" 3/16" 25 125 " 318" 8046957 TEK5O 1224x1 1/2 TEKS5 3125J3/16) 1500 1475 .25a'-114" 1/2" 25 125 1/2" 3831825 0312.0 1/4-14x2"TEKS3 446 (20 .188-3/16" 1/4" 25 125 1!? 8033925 DSTRtO*1/4.20x VTEKS31510(2095.) .036.-20 9a 3/16" 25 125 1/2" 3034925 OSTRS.16" 5/16-18x1.1/4"TEKS3 2220 (209a.) .03F-20 ga 3/16" 25 125 1!? 8035925 DSTS16 5/16-18x1-1/4"TEKS3 1500 (3/16') - .125-1/8" - 3/16" 1/2" 8036925 IF/C 5,0 12-24 a 1-1/2" IF/CS 5 3125 (3/16") ,186".3/16" 1/2' 25 125 SPECIAL NUT DRIVER SYSTEM: The nut drivers were designed with a unique spin-off feature which provides a fast and safe installation each time. When the face of the driver comes into contact with the material you are Installing into, continue drilling until nut driver spins J wai free, kistallation is then complete. Warranty requires the use of the appropriate nut driver for Installations. A - #14 SW Red Not Dfi%W Ptl 8114910 H 'Made with TOO self-drilling fasteners - no pre-drilling required, fl -ImtaII3 Into steel range from 20 gauge - 1/2" thicknesses, opqwtu%• A standard scmwgun with a depth sensitive nosepiece should he used to install Tabs, For optimal fastener performance, the screwgun should be a minimum of 6 amps and have an RPM range of 0-2500. eaves time from traditional methods. Reduces Installation costs. QVlCK to InsIA using the Samrnys Nut Driver with an 18V cordless drill/driver. Manufactured in the U.SA )w'v,ftwbuIWex.comJ 114" 8047957 SWD 100 114-14*1"TKS3 1477 (16 go.) .060"-1556 3/16" 114 8049957 SWORIOO 114-20*1 TEKS3 1900 (20ga) 036 20 p 3/16" 3/6" 8050957 SWD1O 1/4.14x17EflS3 1477 (16 go.) ,060r.169a 3/1ff" - 3/6" 8080925 SWO 10-SS 114.14* 1"TEKS3 1477 (16ga.) .O60"-16a 3/16" 3/8' 8052957 SWO 20 1/4-14 a 2" TEKS 3 1477 (16 go.) .060'-16 ga 3/16" H4 8055957 SWORI 1/420*1 TEKS3 1900 (2Oga) 15001475 036 20ga 3/16 - 3/8" 8054957 SWDR1-1/2" 12-24x1-1/2"TEKS5 2375 (3/16") 1500 1475 ,188".3116" 1/2" 3/6" 8056957 SWOR 516 * 5/16-18* 1-1/4"TEKS 3 2480(20 ga.) - - 1500 1475 -.036"-20- go- - 3116" 3/8" 8057957 SWT 15 12-24* 1-1/2"TEKS 5 2375 (3/16") .188"-3/16" 1/2" "lnckides retaning nut 25 125 25 125 25 125 25 125 25 125 25 125 25 125 25 125 25125 Eliminates distortion of threaded rod in sloped roof applications. Accommodates 3-1/2 x 12 pitch. Installs into angled z-purlin; allows threaded rod to hang plumb, Allows 17" deflection from vertical. Manufactured in the USA, 3220(3/16') 1500 2368(1/2" steel Vertical) 1306(45" off Vertical) 1500 (Vertical) 2281 (3/16' HSS) 850 (45' off Vertical) 1585 (3/16"HSS 45" off Vertical) -- 2368(1/2' steel Vertical) 1306(4S" off Vertical) 2281 (3/16" 1-ISS) 1585 (3116" l'ISS4S' off Vertical) #14 slack Nt4Dhver - Pact # 6113910 POOMWO [SwvE1%!1ouNT 3/8" 8137957 SH-OSTR 1" qL 3/8" 8268957 SH-TEK 50 12-24x1-3/4" 1/2" 8270957 Si-3-TEK 5.0 12-24*1-3/4" '0*ea not comply with ROHS repirementolincludes retaining not Wrpst. Min Max Box Case 1475 .035" 3/16" 25 125 2-1/2" 3/16" 1/2" 25 125 3116" 1/2" 25 125 0 SA 11,11111 Y X_PRESS® Installs into Metal Deck, Purlin, or Tubular Steel The Sammy XPress expands to provide direct vertical attachment in; light gauge steel deck or pudin (22 go. 118'). Installs in seconds with Sammy XPreas 46 Tool, saving time & installation costs. Use in applications where access to Its back of the Installed fastener is prohibited, xi. metal roof deck, tubular deal, or vapor barrier fabric, Less jobsite material needed. No retaftng nut required. 'Provides design flexibility. Manfctared in the USA. C Watch wdeo de,'.crvfröon 8i\ twbutIdex.cJ 13T922 XP200 asrny jt46C22il8j 15(4urrnare) Wr .125' 25 125 MetalOecl 85C (2'' P oei 027" 940 '2' P p 29 '. 38' '85C922 'XP2 SZTM 1146 22g)185 i 1475 4 Pp j) 14 125' 25 125 ct 203 Cc!&CatsI :29" 1500(41PVe) 6O' 4. 4' /$" 8153922 XP 36 tl6oa) 186 (i4Jmna1r8f 029' 94Z'Plp} 125 25 125 PU11 418 (Ce Cae) 059' - - - saffm Pre-Pour Co e-Pour) u 3/9' 8159222 XP2O xo [L Op 1146(21146(229s)8.50(2'/zPpe( 25 125 PozWour lPO5iP- prWPOW utitiI 0 3*0* pit Poid.PowRne$ FCF The Sammy X.Press Sidewinder expands to • Less jobsite material needed. provide horizontal attachment in: 16 go - 3/16' steel- purlin, tubular steel. • No retaining nut required. . • Installs in seconds with Sammy X-Press V Tool, • Provides design flexibility. saving time & installation costs. MmMactw'ed in the U.S.A. Use in applications where access to the back of the installed fastener is prohibited; le, motad roof tSWXP) deck, tubular steel, or vapor barrier fabcic. __. Welch a OdW d fro7 ' www,itwbuildex.comj 'ci 14iJ (Yh.' PIpe) IT 8293357 SWXP35 1798 (16 ga) 80 (Lumnafre) .059 X-Press 35 --.-----.. _41e,lcvt6Cel. 125' 25 125 Pucth AMM VS. ISWOii1 o The Sammy X-Press Swivel allows you to hang plumb in extreme roof pitches: 89 in .puin 4 in metal deck for 12/12 pitch Installs in seconds with Sammy X.Press t Tool, saving time & installation costs. Use in applications where access to the back of VOW the installed fastener is prohibited, ie. metal roof deck, tubular steel, or vapor baffler fabric. Less Iobsite material needed. No retaining out required. Proyft design flexibility. Manufactured in the U.S.A. 0 4.aademonvein at www.11whuiidex.com 750 (T Pipe) Swivel 1061 22 go Vert 170 Vertical (Luminaire) 37 8294922 SXP 20 X Pr 20 ens 829 '45 e 80 45" (Luminatre) .029 635 (2" Pipe) 029" 125" 25 125 Metal Deck 283 Vertical (Conduit & Cable) 233 C 45" (Conduit & Cable) 1250(3.1/2" Pipe) Swivel '' 3/8' 8295922 SXP 35 1675 (16 go Vert) 250 Vertical (Luminaire) ° .029" 125" 25 125 Purlin X-Press35 1558 (89" Off Vert) 635 (2" Pipe) 0cal (Conduit& Cable) 333 @ 89" (Conduit & Cable) Swivel 1/2' 8272957 SXP 2.0 1061 (22 go Vert) .027' .125" 25 125 Metal Deck X.Press20 1/2' 8271957 SXP 3.5 Swivel 1675 (16 go Veil) X-Press3.5 1568(89 Off Vert) .060'" .125" 25 125 Purlin y e / • I • The Sammy X.Press expands to provide I J dined vertical attachment in: ' .. '••"\ zpuin (18-16 gauge) metal deck (22.16 gauge) VO Part Number Model Oescription Oty 8194910 — UXPIT' - - - Unersai X-Prers It Tool 8152910 XPDB 25164" Drill Oft Tool Indudea: Sleeve, Bit Receiver, Hex Wreath, and 25/64" Drill Bit. 40 [SAMMYS® FOR CONCRETE Easy two step process (Drill hole & drtve Samrnys concrete anchor). W pre-drilled pilot hole required, Concrete Installation Tool available for a one tool installation process. Manufactured in the U.S.A. JwwiJflebuiIdex.comJ I VERTICAL OU1T #14 Black 1W 8058957 CS! 200 5t6x1314 2400 25 125 3! 8059957 CST 20 916 1 314 - 2400 1475 25 125 #I4$WRe4 L_ - 8145925 CST20SS 5/16x1-3f4 - - - 2400 25 125 - t4utt)iier 4• 1I2 8060925 CST2 5/16 a 1-3/4 2400 25 125 Pct#4II49I0 - - - - -- - - - -. Tested in 3000 PSI concrete I . Easy two step process (Drill hole & drive Sammys L. e• concrete anchor). t•-i 7 r 0 v' ,. • /..' pre-drilled pilot hole required. !' - Concrete Installation Tool available for a one tool 3P , installation process. Manufactured In the U.SA e- -r : i4*w. '*de,noostration et -.-- www.JlwbuiWex.com Approvals Rod Pan Size Number HORIZONTAl. MOUNT 1W 8052057 1 —ilk-8061857 fts II4SWRed Paitflh149IO SWC200 506a14W 2450 - 25 - 125 SWC2O 5/l6x1-3I4 2450 1475 25 125 Tented in 3000 PSI concrete SPECIAL NUT DRIVER SYSTEM: The nut drivers were designed with a unique spin-off feature which provides a fast and safe installation - each time. When the face of the driver comes into contact with the material you are frwtailing into, continue drilling until nut driver nldris J eco.wriire kiec Installation is then complete, Warranty requires the use of the appropriate nut driver for Installations, I 'Installs vertically and swivels up to 89" in wood & concrete structures. 'eliminates distortion of threaded rod. 1/4" pre-drilled pilot hole required. 'Concrete installation tool available for a one piece Installation process, 'Manufactured in the U.S.A. - 3/8" 8269957 SH.GST/CST2O 5/16x 1.3/4" 1/2" 8303957 SF-GSTICST 20 5/16 a 1-314" UVOW -. - - - - Note: UL Listed for wood- see page 2537 in 3000 psi concrete 1459 cl 45"off vertical in 3000 psi concrete 252 in 6000 psi concrete 1636 @ 45°off vertical in 6000 psi concrete 2537 in 3000 psi concrete 1459 © 45'off vertical in 3000 psi concrete 2852 in 6000 psi concrete 1636 @ 45"off vertical in 6000 psi concrete 25 125 25 125 * Tested in 3000 PSI concrete Application Rotary Hammer Drill into concrete Part Number Description Each Qty Kit includes the following items: 8113810 #14 Black Nut Driver (b) 8114910 #14SW Red Nut Driver (c) 8116910 #250 Bit (1/4')(d) 1 8117910 SDS Bit (1/4") (e) 1 8118910 7f32 Wood Bit (f) 8120910 HEX 250 Bit Receiver (1/4') (g) 1 8098910 SL 250 Sleeve (h) 1 8121910 SOS 8250 Bit Receiver (1/4")" "Only sold separately not included in kit. - ID I ACCESSORIES 1. Pre-drill a 5/8'" hole with a regular drill or hole saw. 2 Insert SST screw into #i4 black nut driver. With wing nut and washer on bolt, Insert wing nut through surface, and begin 66 installation. 3, When bolt is secure and nut driver spins free, stop doll motor and remove Hollow Core 4. W screw is now ready to receive 1/4", 3/8", or Metric all Concrete thread rod or bolt stock. Rod ISize Part Number Model Screw1iT71Th,iii. Ultimate 1l!!TTI11W iioxotf Case city 114' 8063925 SST 300 - 114x 3" 450 (Lath & Plaster) - _25 125 404 (2 Layers 5/8 Rock) [3/8' 8064925 SST 30 1/4 x 3" 40 (Lath & Plaster) 25 125 4 14 Block 404 (2 Layers 5/8 Rock) Nut Driver Part # 8113910 Saeedv Pole TooI for easy installation of ceiling screws without ladders or scaffolding! (see pg 13 for details) 3118" eyelet to accommodate common wire size. [CC approvals can be found at w.itwbuildex.com under Evaluation Report # ER-5367. L - STEEL 8107957 CWSDI" TOM 114x? 2'" (20a) _472 1690. 170 (209a.) 25 125 O ICC t c STEEL 8190957 CWSD 15" Gimlet 114 x 11f2 23/4" 472 (20 go) 20 . 170 (20 go.) 25 125 WOOD Tek$ 1393 (Fir) - L_ICC STEEL 8108957 CWSD2" Teks 114x2" 3.1/4472 (LO ga) l6go. 110(20g0.) 25 125 cwrr CC 8110810 CWlT Installation Toot In taliation Tool Dose-not comply with R011S requirements N IA. ~ MX7MYS j k STAY UPTO 91 I çst jcLfMAflct K(U -fr 2tSUUTED FRUM Complies with NFPA 13 Code Changes. Flashing for dry pendant sprinklers subject to extreme temperature changes. One piece construction is easy to install, Pipe diameter markings ensure accurate fit. PQM temperature range of 65F to +250F. Part Humber Description Pipe Outside Diameter Dektiie Base Drtmeter Dektite Height Box Oty 406491F 2 111W - 3-11e Adaptor Plug (a) Socket Driver for SAMMYS (b) Socket Driver for Ceiling Wire Screws (c) Socket Driver for 1/4" Standard list Drivers (d) Stud Plug for Viper or Ladd Powder Actuated Attachment (e) (Items not sold seperatel) Watch a video dn,onstravonet , www.ltwbultdex.com The Pole Tool and Universal Socket Kit provide easy and safe installation for. Sammys - Jack Chain Threaded Rod -Wire Pencil Rod - Screws Ceiling Screws Ideal for retrofit and hard-to-reach projects in wood and steel. PartT Number Description Box oty 8123910 8124910 - Pole Tool 6(3"-6) Pole Tool 12'(4'- 17) 8125910 0oleT00118(618)___ 8128910 Pole Tool 24(8- 24') 1 .1Speedy PoleTool Installation (spsc1j choIce when ordering pole toot) 8127910 Sammys Socket Driver 1 B289,0 Ceiling Ws-eSocketDriverforwireandchain 8129910 Universal Pole Tool Socket Kit 1 Part Number Model Ea, Oty Product Features 8130910 SpotRite Level 1 J •I/2,314, and rthreading Magnetic strip for ease of use "Pocket Sized Lightweight 34al design for measurement of 00, 450, and 900 angles APPROVALS 8007957 CST 10 3/8" Vertical CPVC 1-1/2" 300 1-1/2" 8020957 $WG 10 3/8" Horizontal CPVC 111/2" 300 1-1/2" 8008557 CST 20 3/8" Vertical 2-112" 850 1-1/2" 4" 1475 1-1/2" 8068925 081 20$$ 3/8' Vertical 2.1/2" 850 1-1/2' 8010957 08130 3/8' Vert/cal 4" 1500 1-1/2" 4" 1475 1-1/2" 8009525 081 25'380 3/8' Vertical 4" 1800 111/2" 8022525 SWG 25.380 3/8" Horizontal 3-1/2" - 4' 1500 1-1/2' 8021957 SWO 20 3/8" Horizontal 2-1/2" - 3'"" 1050 1.1/2" 8073925 SING 20-SS 3/8" Horizontal 2-1/2" 850 1-1/2" 8269957 SH.GST/CST 70 3/8" 45" Angle off Vertical 2-1/2" 850 1-1/2" 8269357 Sl-l-GST/CST 20 3/8" 45' Angle off Vertical 4" 1500 1-1/2" 8139957 SH-(38120 3/8" 17' Angle off Vertical 1050 1-1/2" 4" 1475 1-1/2" 8038357 DSTR 1 3/8" Vertical 4 1500 035" 4" 1475 .105" 6037257 OSIR 11/2 3/8" Vertical 1500 .035" 4" 1475 .155" 8039357 DSTR 816 3/8" Vertical 4 1500 .037" 4' 1475 .105" 8045357 DST 516 3/8' Vertical 4 1500 .188" 4' 1475 .188" 8046357 TEK5O 3/8" Vertical 4 1500 .250" 4" 1475 .188" 8055257 SWOR 1 3/8" Horizontal 4 1500 .031" 4" 1475 .060" 8055257 SWOR 516 3/8' Horizontal 4" 1500 .037" 4" 1475 .060" 8054357 SWOR 1-1/2 3/8' Horizontal 4' 1500 .037' 4' 1475 .060" 8137357 SH-DSTR1 318" 17' Angle off Vertical 4" 1500 .035' 4' 1415 .105' 8268357 SH-TEK 50 318' Vertical 2-1/2" 850 70" Angle off Vertical 4" 1500 8150622 XP 20 3/8" Vertical 2-1/2" 850 .027' , 1475 '105" 8153222 XP 35 3/8" Vertical 4" 1500 .060' 8294822 SXP 20 3/8" Vertical or up to 45' 2" 750 .027" 2" 635 .029" 8295822 SXP 35 3/8" Vertical or up to 89' 3-1/2" 1250 .060" 2 635 .029" 8293957 SWXP 35 3/8" Horizontal 3-1/2" 1250 .060" [SAr!'YS FOR COlCRETE - PIPE HANGER 8055557 CST 20 3/8" Vertical 4" 1475 3000 8061957 SWC 20 3/8" Horizontal 4' 1475 3000 8150922 XP 20 3/8" Vertical 2.1/2" 850 Pre-Pour Structural @3000p5i 8150922 XP 20 3/8' Vertical 2-1/2" 850 Post-Pour Range II LWC 35 PCF (lbs/fl3) 8153922 XP 20 3/8' Vertical 185 .027" 250 035" 185 .027' 8153922 XP 35 3/8" Vertical 250 .035" 8181922 XP 200 1/4" Vertical 185 .027' 250 .035" Vertical 170 .027' 8294922 SXP 20 3/8" 45" 80 .027' Vertical 250 .060' 8295922 SXP 35 90' 3/8 '" 80 .060" 8293957 SWXP 35 3/8' Horizontal 80 .060" 8150922 XP 20 3/8" VertIcal 283 .027' Max 4 trade size EMT, RMC, and lMC&5 trade size riqid PVC condttit 8153922 XP 35 3/8' Vertical 500 .060" Max 4 trade size EMT & 6 trade sze RMC, IMC, and rigid PVC conduit 8294922 SXP 20 3/8' Vertical 283 .027" Max 4 trade size EMT, RMC, and IMC & 5 trade size rigid PVC conduit 8295922 SXP 35 3/8' Vertical 500 .060" Max 4 trade size EMT & 6 trade sze RMC, lMC, and rigid PVC conduit 8293957 SWXP 35 3/8' Horizontal 500 .060' Max 4 trade size EMT & S trade sze RMC, IMC, and rigid PVC conduit 8149987 CZ2000 1/4" or 3/8" Onto Vertical Rod UI. Listed 4516 Plenum Rated, Complies w/ NEC Standards Shect Steel Gauges GaugeNo, 229a. 20 ON. 1608. 1600. 149a 12a- 11" 3/16" 1/4" Nominal Decimal Equivalent .030" .036" .048' .060" .075' .105" 125" .188'" 250" SW3 25-380 Maximum pipe size in cranpooda wood mist stowed by UL is 3-112'" Ut, compliance with NEC Standards. SW3 25-380 Maximum pipe ore in wood limber orjoist stowed by UL is 4 Ut, and FM tests were performed in compliance with NFPa. 13 Standards 20 Maximum pipe size Faotenirrgreqtiirenrent 5 times wei0t of water-filled echatsle 40 pipe plus 250 pounds. SPECIAL NOTES Engineering Note In 1996, the anchors listed by 1,11-were tested in plate steel that measured .188' and .118". Subsequent testing was done for z-pudin applications in May 1997 using (.037') or 20 gauge steel. Most recently in 2008, testing with the new Sammy X-Prese was completed using (.030") or 22 gauge steel metal deck. Sammyst Nut Drivers Special nut drivers were designed to be used with Sammys. When the appropriate nut drivers are used for Installation, the driver spins freely on the screw after installation is complete and eliminates the expected wrist snap, reduces over-torque, and prevents screw failure. Steel Screws Due to variations in hardness of ceflatn metals It should be noted that our self drilling screws for steel will experience different drill speeds 500-1500 RPM drill speed should be used. Metric Products Metric versions of the Sammy anchors are available at www.itwbuildex.com Sammy* for Seismic Please visa w wtwbJlldex,n for out current Seismic product offerring. Vibratory EnvlronmentsV For attaching or anchork,g in th vibratory environments, special care should be taken not just for building attachments but also for the hangers or assemblies being supported, Consult local code authorities for accepted anchoring devices. Composite Joist/Truss Truss manufacturers vary kwtallation recommendations for composite joist. UL testing was completed to validate that Sanimys and Sidewinders SWG 20 and SWG 25,380 can be installed into the top cord of a truss. Sammy 081 20 can be installed into the center of the lower cord of a composite joist. Penetration of the upright center web is permitted by some joist manufacturers. Consult trues manufacturer for recommended installation point. Pre-drilling may be required by joist manufacturers. If so, pre-drill pilot hole 1/8" smaller than root diameter of fastener. Consult the table below: Model TIt Diameter Hole G5120 .182" 1 1/8' GST 25-380 .280" 7/32" SWG2O .182" 1/8" SWG 25-380 .280" 7/32" To increase efficiency of the installation process, sleeve tools, bit receivers, and wood bits are available for pro-drilling, NFPAINEC Standards All UL and FM testing complies with NFPA 13 and NEC standards. Check with your local (AHJ) Authority Having Jurisdiction to confirm application and usage, UL Listings I FM Approvals UL and FM reports are available at wwwitwbuildex.com LP <FM LUO Ire, Technical Drawings Technical drawings are available and can be downloaded at wwwitwbuildeLcorn in the foawing formats: .dwg, ,dxf, and .igs. Manufactured in the U.S.A. Products Sim Contact Information Technical Assistance: (800) BUILDEX Option #8 (x fl59) Customer Service: (800) BUILOEX Option #1 Fig. 25 - Surge Restrainer Size Range - One size fits 3/4" thru 2" pipe Material -Pre-Galvanized Steel Function -Designed to be used in conjunction with TOLCOO Band Hangers to restrict the upward movement of piping as it occurs during sprinkler head activation or earthquake type activity. The surge restrainer is easily and efficiently Installed by snapping into a locking position on the band hanger. This product is intended to satisfy the requirements as indicated in the National Fire Protection Association NFPA 13, 2010 edition, 9.2.3.4,4.1 and 9,2,3.4.4,4 Can be used to restrain either steel pipe or CPVC plastic Pipe. Approvals - Underwriters' Laboratories Listed only when used with TOLCO band hangers Fig. 2, 2NFPA and 200, in the USA (UL) and Canada cUL. Finish - Pre-Galvanized Order By - Figure number and TOLCO band hanger, size from 3/4" thru 2". Patent #5,344,108 COOPER B-LINE 1375 Sampson Ave • Corona, CA 92879 e 800.786.5266 • FAX: 951.737.0330 - COOPER B-Line Size Range - Secures 3/8" thru 7/8" rod in 1" increments Material - Carbon Stool Maximum Temperature - 750°F Finish - Plain Note - Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By - Figure number, rod diameter, rod length and finish Dimensions • Weights Rod Max. Rec. Load Lbs. Size For Service Temps 650°F 750°F 3/8 610 540 1/2 1130 1010 5/8 1810 1610 3/4 2710 2420 7/8 3770 3360 Fig. 98 - Rod Stiffener Component of State of p' California OSHPD Approved c Vt. U3 L83TED Seismic Restraints System Size Range - Secures 3/8" thru 7/8" hanger rod Material - Carbon Steel Function - Secures channel to hanger rod for vertical seismic bracing. Approvals - Underwriters Laboratories Listed in the USA (UL) and Canada (cUL). Included in our Seiic Restraints Catalog approved by the State of California Office of Statewide eglth Planning and Development (OSHPD. For additional load, spacing and placement information relating to OS HPD projects, please refer to the TOLCO ,9eismic RestraintSystems Guidelines Finish Eloctro Galvanized Note Available in HDG finish or Stainless Steel materials. Order By Figure number Fig. 99 - All Thread Rod Cut to Length Fig. 100 - All Thread Rod Full Lengths Size Range - Secures 3/8" thru 7/8" rod in 10' lengths Material - Carbon Steel Maximum Temperature - 750°F Finish - Plain Note - Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By - Figure number, rod diameter and finish Dimensions • Weights Max Rec. Load Lbs. Rod For Service Temps Approx. Size 650°F 750°F Wt./100 1/4 240 215 12 3/8 610 540 29 1/2 1130 1010 53 5/8 1810 1610 84 3/4 2710 2420 123 7/8 3770 3360 169 1 4960 4420 222 11/4 8000 7140 360 11/2 11630 10370 510 OFFICE/MANUFACTURING FACILITY 1315 SAMPSOV AVE.. CORO9A, CA 92879 PH 951.737.5599 • FAX, 951.737.0330 CUSTOMER SERVICE . 800.789.5260 wwwtoIcocoin FIq. 2004 to 2002 L Fig. 200F H A Fig, 2001/2. 200-I4 Fig. M2112 to 200$ Fig. 200 I Fig. 200$ :eitrgeiis Fig. 200 - "Trimline" Adjustable Band Hanger (Cooper B-Line Fig, B317ONF) OVOLM Fig. 200F - "Trimline" Adjustable Band Hanger with Felt Lining (Cooper B-Line Fig, B317ONFF) Fig. 200C - "Trimline" Adjustable Band Hanger with Plastic Coated (Cooper B-Line Fig, 8317ONFC) Fig. 200S - "Trimline" Adjustable Band Hanger with Non-Captured Nut Size Range; Fig. 200 - 1/2" (15mm) thru 8" (200mm) pipe Material: Steel, Pre-Galvanized to G90 specifications Function: For fire sprinkler and other general piping purposes, Knurled swivel nut design permits hanger adjustment after installation. Features: (1/2" (15mm) thru 2" (50mm)) Flared edges ease installation for all pipe types and protect CPVC plastic pipe from abrasion. Captured design keeps adjusting nut from separating with hanger. Hanger is easily installed around pipe. For hanger with non-captured nut order Fig. 200$. (2112" (65mm) thru 8" (200mm)) Spring tension on nut holds it securely in hanger before installation. Adjusting nut is easily removed. Approvals: Underwriters Laboratories listed (1/2" (15mm) thru 8" (200mm)) in the USA (UL) and Canada (cUL) for steel and CPVC plastic pipe and Factory Mutual Engineering Approved (FM) /4" (20mm) thru 8" (200mm)). Conforms to Federal Specifications WW-H-171 E & A-A-1 192A, Type 10 and Manufacturers Standardization Society ANSI/MSS SP-89 & SP-58, Type 10. Maximum Temperature; 650CF (343) Finish: Pre-Galvanized. Stainless Steel ' materials will be supplied with (2) hex nuts - in place of a knurl nut. Order By; Figure number and pipe size -v ' Designed to meet or exceed requirements of FM DS 2-0. (a (I, Fig. ZOOC - 11ii1 11U hr tilljil {J 200_112 1/2" (15) /8'-16 31/8' (79,4) 25/8" (66.7) 11 (5.0) 200-I4 3/4" (20) I8"-16 31/8" (79.4) 21/2" (63.5) 11 (5.0) 200-1 1" (25) /8"-16 33/3" (85.7) 2I' (66.7) 12 (5.5) 200_1114 11/4" (32) /8"-16 33/4" (94.0) 2/8" (73.0) 13 (5.9) 200_11/2 11/2" (40) /811-16 3/8" (98.4) 2/" (73.0) 14 (6.4) 200-2 (50) /8"-16 41/2*' (114.3) (76.3) 15 (6.9) 200_2112 2/2" (65) /811-16 5/8" (142.9) 41/8 ' (104.7) 27 (12.3) 200-3 - 3" (75) Ie"-16 57/8" (149.1) 4" (101.6) 29 (13.3) - 200-3I2 31/2" (90) /8"-16 73/8" (187.3) 51/4' (133,3) 34 (15.6) - 200-4 4" (100) /"-16 7/8" (187.3) 5" (127.0) 35 (16,0) 200-5 5" (125) 1/2"_13 91/3" (231.8) 61/4" (158.7) 66 (302) 200-6 6" 1 (150) 1 1/2"13 101/8" 1 (257.2) 53/4" (171.4) 73 (33.4) 200-8 8' 1 (200) 1 1/2"13 131/8" 1 (333.4) 83/4" (222.2) 136 (62.3) All dimensions in charts and on drawings are in Inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. .1 COOPER B-Line &ipeijgejis Fig. 200M - "Trimline" Adjustable Band Hanger for Metric Rod QuaLcor C®US Size Range: Fig, 200 - 1/2" (15mm) thru 8" (200mm) pipe usm Material: Steel, Pre-Galvanized to G90 specifications Function: For fire sprinkler and other general piping purposes. Knurled -p swivel nut design permits hanger adjustment after installation. ( Features: (1/2" (15mm) thru 2" 5omm)) Flared edges ease Installation for all pipe / \ types and protect CPVC plastic pipe from abrasion, Captured design I keeps adjusting nut from separating with hanger. Hanger is easily A installed around pipe. II - (21/2" (65mm) thru 8" (200mm)) Spring tension on nut holds It securely in hanger before installation, Adjusting nut is easily removed, " Approvals: Underwriters Laboratories listed (/2" (15mm thru 8" 00mm Ftp. 200.1 to 200.2 B in the USA (UL) and Canada (cUL) for steel and CPVC plastic pipe and A - Factory Mutual Engineering Approved 0/4" (20mm) thru 8" (200mm)). Conforms to Federal Specifications WW-H-171 E & A-A-1 192A, Type 10 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 10. / /'' \. _.• Fig. -1/2.200-3/4 Maximum Temperature: 650°F (343°C) Fi1. 200.21/2 to 200-8 Finish: Pre-Galvanized. Stainless Steel materials will be supplied with (2) hex nuts in place of a knurl nut. Order By: Figure number and pipe size VO@W 8 @ IxJJJ1D 200M8-1/2 - W' (15) M8 31/8' (79.4) 2Ia' (66.7) ii 1 (5.0) 200M10-1/2 1/2" (15) MIO 31/8' (79.4) 25/a" (66.7) ii (5.0) 200M8-3/4 3/4" (20) M8 31/8" (79.4) 21/2" (63.5) 11 (5.0) 200M10-3/4 3/4" (20) M10 31/8' (79.4) 21/2" (63.5) 11 (5.0) 200M8-1 1" (25) M8 3I" (85.7) 2I8" (66.7) 12 (5.5) 200M1 -1 1" (25) MiD 3t8" (85.7) 2f' (66.7) 12 (5.5) 2001Y18-11/4 11/4" (32) MB 33/4" (94.0) 2/" (73.0) 13 (5.9) 200M10-11/4 11/4" (32) MiD 3/4" (94.0) 2f&" (73.0) 13 (5.9) 200M8-11/2 11/2" (40) MB 3/" (98.4) 2I8" (73.0) 14 (6.4) 200M10-11/2 11/2" (40) M10 3/a" (98.4) 2/8" (73.0) 14 (6.4) 200M8-2 (50) MB 41/2" (114.3) (76.3) 15 (6.9) 200M10-2 2" (50) Mb 41/2° (1143) 3' (76.3) 15 (6.9) 200M-21/2 21/2" (65) MiD 5/" (142.9) 41/8" (104,7) 27 (12.3) 200M-3 3" (75) MiD 5/° (149,1) 4" (101.6) 29 (13.3) 200M-31/2 31/2" (90) MiD 7/" (187.3) 51/4" (133,3) 34 (15.6) 200M4 4° (100) MiD 7/8" (1873) 5" (127,0) 35 (16.0) 200M-5 5 (125) M12 91/8" (231.8) 61/4" (158.7) 66 (30.2) 200M-6 6' (150) M12 101/8" (257.2) 6/4" (171,4) 73 (33.4) 200M-8 8' (200) M12 131/8" (333.4) 8/4' (222.2) 136 (62.3) All dimensions in charts and on drawings are In inches, Dimensions shown in parenneses are In millimeters unless otherwise specified. COOPER B-Line Designed to meet or exceed requirements of FM DS 2-0. ERIJ Fig. 200H - Heavy Duty Band Hanger (For Trapeze) Size Range: 2" (50mm) thru 4" (1 00mm) trapeze pipe size. Material: Steel — Pre-Galvanized to G40 Spec Function: Designed primarily to support substantially heavier loads than is normally intended for the nominal hanger size. Used extensively to support trapeze installations and the increased loads from both above and below the trapeze assembly. Features: Furnished with /8'16 or 1/2°13 adjusting threaded ring nut. Approvals: Underwriters Laboratories listed in the USA (UL) and Canada** (cUt.). Conforms to Federal Specification WW-H-171E & AA1 192A, Type 10 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 10, Maximum Temperature: 650°F 343°C) Finish: Pre-Galvanized Order By: Figure number, pipe size and rod size. Important Design Note. Because of the increased loads applied to the trapeze assembly, both the upper trapeze supports as well as the lower hanging unit must be able to hold the maximum loads intended. I [F] L. !i ~WR - ti; 11 W1 To IfTh i Vo 200H-2-3/8 2' (50) /81-16 4I1' (115.9) 3I32' (81.7) 48 (21.8) 200H-2-112 2" (50) 1/2"_13 423/32° (119.8) 33f" (85.7) 45 (20.4) 200H-21/2-3/a 21/2" (65) /8'-16 5I16' (134.9) 323/32 (94,4) 59 (26.7) 200H-21/2-1/2 21/2 (65) 1I2'-13 515/32° (138.9) 37/8' (98.3) 56 (25.4) 20OII-3-/8 3' (75) I"-16 53/4" (146,0) 327/37" (97.6) 63 (28.6) 200H-3-1/2 3" (75) 112'_13 5/8" (148,1) 331/32" (100.8) 60 (27.2) 200H-4-318 - 4" (100) /81-16 618" (174,6) 4I1' (112.7) 76 (34,5) 200Ii4.1/2 4" 1 (100) 1/2°_13 71/32" 1 (178.6) 419132" (1116.7) 73 (331) * Select trapeze pipe size based on section modulus required for span of trapeze per information provided in NFPA 13, All sizes are UL Listed to support up to 8' pipe at max spacing per NFPA 13. For 6" (150mm) and 8" (200mm) trapeze pipe, consult factory. All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. COOPER B-Line Application LubeFit® should be applied in an even and thin amount over the parts to be lubricated. Avoid applying excessive amounts. The best applicaion is achieved when applying by hand. Clean all dirt, burrs and foreign matter from the joint surfaces. Make certain the gasket is properly located. Apply an even coating of lubricant to all fitting surfaces and gasket. Assemble the joint according to the pipe fitting manufacturer's directions. Disclaimer DO NOT ALTER THE CONSISTENCY OF THIS PRODUCT. Use as is directly from the container. Keep away from your mouth and eyes. If eye contact occurs, fl ush with water for 5 minutes. If discomfort persists get medical attention. *Will stain untreated porous surfaces such as concrete if not cleaned from the surface immediately. Specifications Appearance: Dense, paste like consistency and is light brown or tan in color. Contains: Potassium Oleate, Propylene Glycol and Mica. Contains NO PETROLEUM. Packaging: 21b (1-quart approx.) 55-gl drum (400 lbs. approx.) See Material Safety Data Sheet for additional safety and disposal information at www.fppi.com CAUTION: Eye irritant. Avoid contact with eyes. Wash thoroughly after use. [Mur bFff I OR- ERI ! U7 1 Rri i aT F P P I Description LubeFit® is a vegetable fiber based lubricant for all gasketed fittings, including grooved couplings for fire sprinkler systems. It is non staining* and does not support bacterial growth. LubeFit® can be easily applied in temperatures from -10°F to 150°F LubeFit® is non-toxic and water soluble. Under normal conditions, LubeFit® is not harmful to the skin. Design Criteria/Data Water dispersible Applies equally well to wet or dry surfaces Suitable for all types of pipe lines, including potable water Excellent working range -10° to 1500 Will not support bacteria Will not deteriorate natural or Synthetic rubber, plastic gaskets or caston iron pipe FGG/BM/C System Compatible Program* Certified to NSF/ANS/Std 61 -G m C:) V— CD t/1. VwMerm-p-T-mir *FBC System Compatible indicates this product has been tested by Lubrizol Advanced Materials and is monitored on an on going basis to assure chemical compatibility with FlowGuard Gold®, BlazeMaster, and Corzan® pipe and fittings. ,. L 3198 UONSHEAD AVE CARLSBAD, CA 92010 I TEL+ 1760 599-1168 i J +1800344-1822 FAX + 1800 344-3775 wu © 2012 Fire Protection Products, Inc. FPPf', LubeRtO are registered trademarks of Fire Protection Products, Inc. LA FGG/BM/CZ', Blaze-Master5, F!owGuard Gold5 and Corzan® are registered trademarks of Noveon IP Holdings Corp. NIADE U.S.A. ••••,i• ngiPã't Description Pipefit® Thread Sealing Paste with PTFE is a premium non-hardening PTFE filled pipe thread sealing paste designed specifically for the fire sprinkler industry. Pipefit is suitable for use on all threadable materials commonly used in fire sprinkler systems, including CPVC. Pipefit's unique blend of materials provides superior thread sealing qualities over other similarly priced sealants The particulate PTFE also helps prevent leaks by accumulating in the voids of damaged or defective threads of the pipe or fittings. Additionally, the lubricating qualities of the PTFE and other materials in the sealing paste improve thread seating during pipe and fitting assembly. Pipef it® also adheres well to hot oily pipe present in "high speed' fabrication operations. Design Criteria/Data Recommended Use Water Air Refrigerants Natural Gas Mild caustics Steam Kerosene LP Gases Acids Gasoline Diesel Fuel Ammonia Use for threaded connections on steel, aluminum, brass, PVC, CPVC and ABS. Operating temperature ranges -50 f to 500 f. *FBC System Compatible indicates this product has been tested by Lubrizol Advanced Materials and is monitored on an on going basis to assure chemical compatibility with FlowGuard Gold®, BlazeMaster, and Corzan® pipe and fittings. 3198 LIONSI-IEAD AVE L ) CARLSBAD, CA 92010 TEL+ 1760 599-1168 + 1 800 344-1822 FAX +1800344-3775 Installation Make sure that the threads are free from burs and other debris. Apply Pipefit® liberally to the male pipe threads. Make sure that the thread sealant is brushed into the "root" of the threads. Do not wipe off excess material until fitting has been "made on" to the pipe thread. The threading action of the fitting to the pipe will allow the proper amount of sealant to remain in the connection. Wipe off excess sealant. Pipef it® will not dry out under normal conditions. Never use dope and tape together. Keep covered when not in use to avoid contamination. Some settling of the product may occur. Occasional stirring may be necessary. Two year shelf life. Disclaimer DO NOT ALTER THE CONSISTENCY OF THIS PRODUCT. Use as is directly from the container. Keep away from your mouth and eyes. If eye contact occurs, flush with water for 5 minutes. If discomfort persists get medical attention. Specifications Appearance: Dense, paste-like consistency, off white in color. Packaging: 16 oz. brush in cap 32 oz. 32 oz. BIG 1 gl. 5 gl. 55 gl. CAUTION: See MSDS for first aid instructions. Wash hands thoroughly after each use. See Material Safety Data Sheet for additional safety and disposal information at www.fppi.com I Nu © 2012 Fire Protection Products, Inc. FPPI, LubeFit5 are registered trademarks of Fire Protection Products, Inc. FBC', B/azeMaster', FlowGuard GoVO and Co,zan° are registered trademarks of Noveon IP Holdings Corp. Spears Compatible indicates that ThreadFie CLEAR has been tested by Spears Manufacturing to be compatible with Flameguard' pipe and fittings. 'Gfflj9:7fA1f1 111 ~§][Cff I OEM I &942t _, 12 Description ThreadFit® CLEAR Thread Cutting Oil for Sprinkler Pipe is an excellent heavy duty, light colored cutting oil for all types of ferrous metal. It's special combination of anti-wear and anti-weld additives provides all the necessary lubricity and cooling modern pipe threading operations require. This balanced combination of additives will help improve die life and thread quality over other cutting oils and is Chlorine free. ThreadFit Clear's low smoke/ low odor formulation makes it ideal for use in high speed threading applications. FP P 1 ThredflI' No 0 2013 Fire Protect/on Products, Inc. FPPP, ThreadFV are registered trademarks of Fire Protection Products, Inc, Features Heavy Duty Cutting Oil Excellent Tool Life Chlorine Free All types of ferrous metal or pipe Improved Surface Finish Low Odor Low Smoke SYSTEM COMPATiBLE *FBCTI System Compatible indicates this product has been tested by Lubrizol Advanced Materials and is monitored on an on going basis to assure chemical compatibility with FlowGuard Gold, elazeMaster', and Corzan' pipe and fittings. 3198 LIONSHEAD AVE CARLSBAD, CA 92010 TEL +1 760 599-1168 +1800344-1822 FAX + 1800 344-3775 Installation ThreadFit0 can be used in automatic and hand held applicators. Fill oil reservoir according to equipment manufacturers specifications. Mixing of different types of threading oils is not recommended. DO NOT ALTER THE CONSISTENCY OF THIS PRODUCT. Use as is directly from the container. Change oil regularly for optimum performance. Contains petroleum oil. Avoid breathing mists or vapors. Avoid eye contact and prolonged or repeated contact with skin. Wear safety glasses or goggles. Use good personal hygeine. Dispose of used oil in accordance with all local, State and Federal ordinances and regulations. Consult Material Safety Data Sheets for additional safety and handling information. DO NOT MIX WITH OTHER THREAD CUTTING OILS OR CONTAMINANTS. Specifications Appearance: Clear amber liquid. Packaging: 1 gl. (6/case) 5 gl. Pail 55-gl drum 275-gl tote CAUTION: Skin contact: wash thoroughly with soap and water. Eye contact: flush eyes with water for at least 15 minutes and seek medical attention. Ingestion: consult a physician immediately. Inhalation: move affected person(s) to fresh air and seek medical attention. See MSDS for first aid instructions. Spill or Leak: Soak up with an oil absorbent compound. Follow all state, local, Federal regulations for disposal. Don't pollute. Conserve our resources-Please recycle this container. See Material Safety Data Sheet for additional safety and disposal information at www.fppi.com This product is registered with CHEMTREC, a 24-hour emergency hotline. They may be reached at 1 800 424-9300.