Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
7710 EL CAMINO REAL; ; FA160006; Permit
City of Carlsbad Fire Alarm Permit Permit No: FA160006 7710 EL CAMINO Job Address: REAL Permit Type: FALARM Parcel No: 2161241600 Lot #: 0 Reference No.: PC #: Status: ISSUED Applied 1/26/2016 Approved: 2/24/2016 Issued: 2/24/2016 Inspector: Project Title: EQUINOX FITNESS CLUB TI- NEW FIRE ALARM SYSTEM TO BE INSTALLED 2/25/16 correction made to total fees Applicant: DSP ELECTRIC 79 E GRAND AVE CORONA, CA 92879 949-235-2400 Owner: EXCEL IVLA COSTA OWNER LLC C/O TAX DEPT 17140 BERNARDO CENTER DR #300 SAN DIEGO CA Fees ($) Add'l Fees ($) Total ($) Balance ($) 452 0 452 0 INTELLIGENT FIRE ALARM CONTROL UNIT FX-350-60-DR .9 FA1 60006 7710 EL CAMINO REAL Description The FX-350-60-DR Intelligent Fire Alarm Control Panel is a single loop addressable panel that supports up to 60 addressable points. The FX-350-60-DR is equipped with a two line by 20 character backlit LCD display, numerical keypad and an integrated UDACT/Digital Communicator. The LCD display allows for 32 characters to be configured for user defined messages. In addition the FX-350 Series family also includes remote LED and LCD annunciators. The FX-350-60-DR is ideal for both new and retrofit applications. Designed for small to medium commercial, institutional and industrial occupancies, these panels are powerful enough to meet today's installation demands. The FX-350-60-DR is configurable by the keypad for onsite programming or by a PC for both onsite and remote programming. Easy to install and simple to operate and configure, the FX-350-60-DR enables the installer to configure the system to meet their specific requirements. The FX-350-60-DR is equipped with a 5.5 Amp power supply, auxiliary resettabte smoke power supply (300mA max.), an interface for a Remote Trouble Indicator (RTI- 1) and an RS-485 interface for remote LCD and LED annunciators. The FX-350-60-DR comes complete with a red door, black enclosure, durable CAT-30 lock and key and space to mount up to 12 AH batteries. An optional trim ring is available for semi-flush mounting. Features Single Addressable SLC Loop that supports 60 addressable points Points can be any combination of Addressable Sensors or Modules Supports Ionization Sensors, Photoelectric Sensors, Variable Heat Sensors and Multi—Sensor (Heat/Photo) Equipped with a 2 line by 20 character backlit LCD display, numerical keypad and an integrated UDACT/ Digital Communicator LCD display allows for 32 characters to be configured for user defined messages Digital Communicator can be configured for DACT or UDACT mode of operation Configurable via the front panel, PC Configurator, or remote dial up through the built-in modem Sensors can be configured as Alarm, Verified Alarm, Latching or Non-Latching Supervisory, Monitor and Trouble-Only Modules can be configured as Alarm, Latching Supervisory, Non-Latching Supervisory, Water Flow, Monitor, Trouble, Fire Drill Switch, Signal Silence Switch, Aux Disconnect Switch and Buzzer Silence Switch Base panel is equipped with Four Class "B" (Style "B") indicating circuits which may be configured as Class "A" (Style "Z) using a Class "A" signal converter module Indicating Circuits may be configured as Silenceable or Non-Silenceable for both signals and strobes Built-in sync protocols for the following strobe manufacturers: Mircom, Amseco, System Sensor, Gentex, Faraday and Wheelock Relay contacts for Common Alarm, Auxiliary! Alarm (Disconnectable), Common Supervisory and Common Trouble Configurable Signal Silence Inhibit, Auto Signal Silence and One-Man Walk Test SubsequentAiarm, Supervisory, and Trouble operation RS-485 Interface for Remote LED and LCD Annunciators Positive Alarm Sequence Interface for a Remote Trouble Indicator (RTl-1) Two event history logs comprised of a 200 event alarm log for alarm related events and a 200 event general log for all other events 5.5 Amp Power Supply Optional City Tie/Polarity Reversal module Optional trim ring for semi-flush mounting ® MEA approved Chi go Approved for S7010 7165-1477:156 31397E Class I Applications MV CATALOG NUMBER 5670 NOT TO BE USED FOR INSTALLATION PURPOSES. Mircom reserves the right to make changes at any time without notice in prices, colours, materials, components, equipment, specifications and models and also to discontinue models. Optional Adder Modules 0CAC-304 Four Indicating Circuit Class "A" Converter Module The OCAC-304 converts four Class "B" (Style "Y") output circuits on the FX-350 to Class "A' (Style "Z") circuits. The OCAC-304 is equipped with wire leads to connect to the FX-350 main board. Remote Annunciators PR-300 Polarity Reversal/City Tie Module The PR-300 provides outputs for city box and polarity reversal applications. As a city be module the PR-300 provides an interface between the control panel indicating circuits and a master box. As a polarity reversal module the PR-300 provides an interface between the control panel and a reverse polarity receiver. RAM-300LCDR Remote LCD Annunciator The RAM-300LCDR provides LCD remote annunciation through a 2 line by 20 character LCD display. The RAW 300LCDR provides control switches for System Reset, Signal Silence, Fire Drill and Acknowledge as well as a numeric keypad to access the menu functions. The common control functions can be disabled on a per function basis. The RAW 300LCDR has LED indicators forA.C. On, Alarm, Supervisory, Trouble and CPU Fail. The RAM-300LCD comes complete with a red enclosure and a CAT-30 Lock and key. RA-1 000 Series Remote LED Annunciators The RAM-1016TZ and RAM-1032TZ Remote LED Annunciators provide 16 or 32 points respectively of LED annunciation. Both models come standard with bi-coloured LEDs which are automatically configured for either Alarm (Red) or Supervisory (Amber). The annunciators have indicators forA.C. On, Common Trouble and Signal Silence and controls for System Reset, Lamp Test, Fire Drill, Buzzer Silence and Signal Silence. In addition both models allow for the control switches to be disabled on a per function basis. Both models mount in a BB-IOOIR enclosure. RAM-208R/RAM-216R Remote LED Annunciators The RAM-208R and RAM-216R provide 8 or 16 points respectively of LED annunciation. Both models feature bi-coloured LEDs which are auto-configurable for eitherAlarm (red) or Supervisory (amber). The LED annunciators have indicators forA.C. On, Common Trouble and Signal Silence and control switches for System Reset, Signal Silence, Lamp Test and Buzzer Silence. The RAM-208R and RAM-216R are equipped with a keyswitch which allows for enabling and disabling of the Common Control functions. Both models are available in a red finish and mount in a 4-gang electrical box. Dimensions FX-350-60-DR 20"H x I4WW x 4%"D Ordering Information Model Description FX-350-60-DR Single Loop 60 Point Intelligent Fire Alarm Control Panel with built-in UDACT/Digital Communicator FA-300TRB Black semi-flush trim ring for FX-350-60-DR enclosure Optional Adder Modules OCAC-304 Four Indicating Circuit Class "A" Converter Module PR-300 Polarity Reversal/City Tie Module Remote Annunciators RAM-300LCDR Remote LCD Annunciator clw enclosure. RAM-i O16TZ 16 Zone Remote LED Annunciator with trouble LEDs. Mounts in an B13-1 000 Series enclosure. RAM-1032TZ 32 Zone Remote LED Annunciator with trouble LEDs. Mounts in an BB-1 000 Series enclosure. BB-1001R Red enclosure for RAM-1016TZ or RAM-1 032TZ Annunciators. Houses I module. RAM-208R 8 Zone Remote LED Annunciator RAM-216R 16 Zone Remote LED Annunciator NOT TO BE USED FOR INSTALLATION PURPOSES. Ali,, M i r c o m - - Canada 25 Interchange Way Vaughan, Ontario L4K 5W3 Telephone: (905) 660-4655 Fax: (905) 660-4113 Distributed by: U.S.A. 4575 Witmer Industrial Estates Niagara Falls, NY 14305 Toll Free: (888) 660-4655 Fax Toll Free: (888) 6604113 Web page: http://www.mircom.com Email: mail@mircom.com SO qoouou IrKN CAT. 5670 REGISTERED - Rev. 3 ALPHA INTELLIGENT ADDRESSABLE MODULES MIX-I 00 SERIES MIX-101P MIX-1 OOP MIX-100S MIX-I OOX Features Designed to meet a wide range of applications For use with the FX-350 Series Fire Alarm Control Panels Fast response time Priority Interrupt feature on monitor modules Monitor modules can be wired as a Class A (Style D) or Class B (Style B) Each module can be addressed from Ito 126 Eight position dip switch for address setting Red light indicator Modules mount in standard 4" junction box S Description Mircom's Alpha Series Intelligent Addressable Modules are designed to meet a wide range of applications. The monitor and control modules can be used to supervise and activate sounders, strobes, door closers, pull stations, waterflow switches, conventional smoke detectors and more. An eight position dip switch allows for the address setting of the device and the wiring class/style of the devices that are connected to the module. All modules mount in a standard 4" x 4" x 2 1/8" junction box. Intelligent Addressable Priority Monitor Module (MIX-loop) The Intelligent Addressable Priority Monitor Module (MIX-1 OOP) provides an address for a group of ULJ ULC Listed normally open (N.O.) initiating devices, such as heat detectors, beam smoke detectors, 4- wire smoke detectors, waterfiow switches, manual pull stations, etc. wired in a Class A (Style D) or Class B (Style B) initiating circuit. The MIX-100P is equipped with a priority interrupt to provide a fast response to emergency conditions. The MIX-100P has an activated red LED. Intelligent Addressable Priority Mini-Monitor Module (MlX-I01P) The Intelligent Addressable Priority Mini Monitor Module provides an address for a group of UL/ULC Listed Normally Open (N.O.) initiating devices, such as heat detectors, projected beam smoke detectors, 4-wire smoke detectors, waterfiow switches, manual pull stations, etc. wired in a Class A (Style D) or Class B (Style B) initiating circuit The MIX-101P is equipped with a priority interrupt to provide a fast response to emergency conditions. The MIX-101P has an activated red LED. Intelligent Addressable Relay Module (MIX-IOOR) The lntelligentAddressable Relay Module connects to the same loop as the initiating devices and provides two isolated sets of Form-C contacts to control a variety of normally open or normally closed contact applications cuch as fan operation and door closures. The MIX-I OUR has an activated red LED which follows the state of the relay contacts. @@0 S5434 S5434 7150-1477:156 W CATALOG NUMBER 5675 NOT TO BE USED FOR INSTALLA11ON PURPOSES. Mircom reserves the right to make changes at any time without notice in prices, colours, materials, components, equipment, specifications and models and also to discontinue models. S Intelligent Addressable Supervised Control Module (MIX-100S) The MIX-100S Control module provides supervised monitoring of wiring to signal devices that require an external power supply to operate, such as horns, strobes, bells or speaker isolators. Conventional signals will require a 24 VDC power source and speakers will require an audio input. The red LED will illuminate when the module is activated. The module is capable of Class A (Style Z) or Class B (Style Y) supervision. Specifications General Specifications Operating Voltage 16-28 VDC Communication mmU Class A (Style D) or Class B (Style B) switch selectable Relative Humidity 0% to 95% (No condensation or icing) MIX-1 OOP and MIX-IOIP Current Consumption 600 pA Alarm Current 4.6 mA (LED on) Dimensions MIX-100P 4.0" W x 4.0" H xi .3" D MIX-I01P 3.O"Wx2.0"HxO.75"D Weight MIX-1 GOP 3.0 oz. (85.8g) MIX-i 01 P 1.5 oz. (42.6g.) MIX-100S Current Consumption 1 mA Source Power Signals 1 24 VDC regulated Speakers 70.7 V RMS Ratings 2A @ 3OVDC, 0.6A @ I25VAC Dimensions 4.0" W x 4.0"H x 1.3"D Weight 3.0 oz. (85.8g) Fault Isolator Module (MIX-100X) The MIX-100X Fault Isolator Module is used to protect the system against wire-to-wire short circuits on the analog loop. The modules should be spaced between groups of sensors or modules in a loop to protect the rest of the loop. In the event of a short circuit between any two fault isolator modules, both modules immediately switch to an open circuit condition and isolate any group of sensors between them. The remaining units on the circuit will continue to operate in a normal fashion (must be wired in Class 'A' or Style 6). Operating 0°F to +155°F (-20°C to +70°C) Temperature Housing/Cover White Polycarbonate Plate Finish MIX-100X Current Consumption 35pA at 24V Max Line Current 1 Amp Line Resistance 0.2 ohm Dimensions 4.0"Wx4.0"Hx1.3"D Weight 3.0 oz. (85.8g) MIX-10011 Current ConsumptIon 250 pA Ratings 2A @ 24VDC, 0.5A @ 30VAC Dimensions 4.0" W x 4.0" H x 1.3" D Weight 3.0 oz. (85.8g) Ordering Information Model Description MIX-lOOP Intelligent Addressable Priority Monitor Module MIX-i 01 P Intelligent Addressable Priority Mini Monitor Module MIX-i OOR Intelligent Addressable Relay Module MIX-lOGS Intelligent Addressable Supervised Control Module MIX-i OOX Fault Isolator Module NOT TO BE USED FOR INSTALLATION PURPOSES. Alki, M i r c o m Distributed by: Canada U.S.A. 25 Interchange Way 4575 Witmer Industrial Estates Vaughan, Ontario L4K 5W3 Niagara Falls, NY 14305 Telephone: (905) 660-4655 Toll Free: (888) 660-4655 Fax: (905)660-4113 Fax Toll Free: (888)660-4113 Web page: http://www.mircom.com Email: mail@mircom.com ISO 9001:2008 (i\ REGISTERED se' CAT. 5675 Rev. 2 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7165-1477:0156 Page 1 of 2 CATEGORY: 7165 - FIRE ALARM CONTROL UNIT (COMMERCIAL) LISTEE: MIRCOM TECHNOLOGIES, LTD.25 Interchange Way, Vaughan, Ontario L4K 5W3 Canada Contact: Mara Cherubin (888)660-4655 Ext: 3110 Fax (888)660-4113 Email: mcherubincmircom.com DESIGN: Models FX-350-60-R, FX-350-60-DR, FX-350-126-R, FX-350-126-DR, FX-351-LW, *Fx351..LD FX-351-LDW, FX-353-LDR, FX-353-LDW and FX-350-378-DR fire alarm control units. Local, auxiliary, remote station (PPU), central station (PPU), waterflow and sprinkler supervisory services. Refer to the listee's data sheet for detailed product description and operational considerations. System components: MD-815; FX-350/FX-351 Mainboard - with Dialer BBX-1 024DS(R); Universal Backbox MD-837; FX-350/FX-351 Mainboard - NQ Dialer MD-749; DSP Core Board MD-819; Power Supply Board PR-300; City Tie/Polarity Reversal TR-061; 120/240 VAC Transformer CH-613; FX-350 Backbox FX-350 Door FX-350 Deadfront FX-351 Deadfront • FX-351 Door FX-351 Backbox MD-825; *RA)( 332 RAM-300-LCD; Remote LCD Annunciator MIX-loop; Priority Monitor Module MlX-101P; Mini Priority Monitory Module MIX-100S; Supervised Control Module MIX-I OOR; Addressable Dual Relay Output Module MIX-100X; Isolator Kit *Rev. 11-14-13gt This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2015 Listing Expires June 30, 2016 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division Listing No. 7165-1477:0156 Page 2 of 2 RATING: 120 VAC, 60Hz 240 VAC, 50 Hz INSTALLATION: In accordance with listee's printed installation instructions, applicable codes & ordinances, and in a manner acceptable to the authority having jurisdiction MARKING: Listee's name, model number, electrical rating, and UL label. APPROVAL: Listed as fire alarm control units for use with listee's separately listed electrically and functionally compatible initiating and indicating devices as indicated in design. Refer to listee's Installation Instructions Manual for details. These control units can generate a distinctive three-pulse Temporal Pattern Fire Alarm Evacuation Signal (for total evacuation) in accordance with NFPA 72, 2002 Edition. NOTE: For Fire Alarm Verification Feature (delay of fire alarm signal), the maximum Retard/Reset/Restart period shall not exceed 30 seconds. This control panel meets the requirements of UL-864, 9th Edition. *Rev. 11-1413 gt This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2015 Listing Expires June 30, 2016 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division FrQrn Tyc Swiiy Ptthicf 3G technology from DSC! Features That Make a Difference: Uses HSPA (3G) network for high-speed, reliable and low- cost communications to an IP receiver Automatically switches to 2G (EDGE/GPRS) if 3G service is not available Compatible with control panels that communicate using the Contact ID format Full event reporting 4 on-board inputs 4 on-board outputs (open collector) SIM card (included) Activation and initialization via automated telephone activation system (VRU), web-user or mobile interface provided by C24 Communications PTM (Panel Transmission Monitor) switches from PSTN to cellular on unsuccessful communication attempts Compatible with Sur-Gard System I IP/H/lll/lV/5 monitoring station receivers Includes UL listed power supply, transformer and 7 Ah rechargeable battery UL 864 listed CSFM listed The 3G3070CF connects the alarm control panel to the HSPA network and reports alarm signals directly to a monitoring station receiver (Sur-Gard System l-IFI1I/llJlvl5). The 3G3070CF uses the HSPA network to ensure low-cost, high-speed and reliable alarm communica:ions and is compatible with control panels that communicate using the Oontact ID format. The 3G3070CF is complian: with the latest requiremens for Communications Methods as per UL864 and NFPA72 201C and 2013 Editions. It can be used in Fire Monitong applications as a single communications technology, in which case any failure cf the communications path shal be annunciated at the supervising station within 5 minutes (NFPA72 2010) or 1 hour (NFPA72 201 ai of the failure, or it can be used as part cf a multip,e communications technologies (for example in conjunction whh a DACT). When used as a back-up provision shall be made to monitor the integrity of each communication path and failure of any communications path shall be annunciated at the supervising station and at the protected premises within not more than 24 hours of the failure. How it Works The 3G3070CF can be used as either a So,e Communicator or as a Backup Communicator. When being used as a Sole Communicator the 3G3070CF will replace the phone line connection on the panel and as soon as it detects that an alarm needs to be transmitted it will send the alarm across the HSPA network immediately. When being used as a backup the communicator assesses the connection to the PSTN phone line, and only in the event of a phone line failure will it send all alarm traffic across the -ISPA network to the monitoring station. In instances where the control panel does not support Contact ID, the C From 'ryco Security Products 3G3070CF has inputs pre-set to transmit fire alarm, fire supervisory or system trouble. Alarm signals are transmitted directly without the need of a cleannghouse to the IP linecard of the monitoring station receiver (Sur-Gard® System l/ll/lll/IV/5). Activating & initializing the unit Activating and initializing the 3G3070 can be done using the automated telephone activation system (VRU), mobile interface or web-user interface provided by CONNECT 24. No special tools are required. UL Listing The 3G3070CF is UL listed under File $4019, Listing guide UO)O(, as a sole or backup communicator for Commercial Fire monitoring installations. When used a a sole communicator under NFPA72 2010 guidelines the 3G3070CF will send its heartbeat once every 97 seconds ensuring that three heartbeats will be received at the supervising station within the 300 second window. When used as a sole communicator under NFPA72 2013 guidelines the 3G3070CF will send its heartbeat once every 5 minutes to monitor connectivity with the supervising station within the 1 hour window. When used as a backup communicator the 3G3070CF will monitor the other communication method (DACT) and send a daily test transmission to the supervising station. CSFM Listing The .G3070CF has been approved by the California State Fire Marshal (CSFM) pursuant to Section 13144.1 of the California Health and Safety Code. Rate Plan Cost-effective rate plans have been negotiated and are available through authorized master resellers. Contact your monitoring station or visit w.connect24.com to find a master reseller. Specifications Dimensions....................... 11-112'x10"x3' (29.2 cm x 25.4 cm x 7.62 cm) Input Voltage.............................................................120 VAC CurrentDraw .............................................................. 300 mA Operating Environment ................32° to 120° F (00 to 48° C) Weight...........................................................12.8 lbs (5.8 kg) Ordering Information: 3G3070CF-USA ..... Universal Wireless Commercial Fire Alarm Communicator (U.S. Model/SIM Card Included) 9 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7300-1273:0140 Page 1 of 1 CATEGORY: 7300-- FIRE ALARM CONTROL UNIT ACCESSORI ES/MISC. DEVICES LISTEE: Digital Security Controls95 Bridgeland Ave, Toronto, Ontario M6A 1Y7 Canada Contact: Dan Nita (905) 760-3000 Fax (905) 760-3020 Email: dnitatycoint.com DESIGN: Model 3G3070-CF, RF communicator (GSM-GPRS or 3G/HSPA network) signaling device. It is intended for use as a standalone communication technology (standalone unit). It may also be used as a backup communication technology in conjunction with a DACT. It is used for central station fire and burglar alarm system communication, which employs a GSM-GPRS or 3G/HSPA (cellular) communication as its signaling medium. This product is to be connected to a listed control panel in accordance with the installation instructions provided with the Model 3G3070-CF transceiver. A Motorola radio, Model H24, connects to an interface board, Model UA595, to form a Model 3G3070-CF communicator, which is intended to be installed at each protected premise. The Model 3G3070-CF is housed in its own metal enclosure and can connect to any separately listed control unit through a telephone line connection or using its inputs connected to dry contacts outputs from the fire alarm control panel for alarm, supervisory, or trouble transmissions. Refer to listee's data sheet for additional detailed product description and operational considerations. RATING: 120V, 50/60 Hz, 03A INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating, and UL label. APPROVAL: Listed as communicator signaling device for use with a separately listed fire alarm control unit. Refer to listee's Installation Instruction Manual for details. Q2-09-12 gt This listing Is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed xx the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2015 Listing Expires June 30, 2016 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division ACE-Il ( FIRE ALARM DOCUMENTS The FAD is the perfect fit to meet the demanding code requirements today. SAE's number one goal is to manufacture code compliant solutions and this product allows you to do just that. NFPA 72 2007 section 6.2.2.1 states, "A record of installed software and firmware version numbers shall be maintained at the location of the fire alarm control unit." This durable 16 gauge steel enclosure with a solid piano hinge and key lock will keep all of your code required documents in one safe place. With a 4GB USB flash drive it stores your fire alarm software safe and secure eliminating the occurrences of the soft- ware not being on site when technicians arrive to service the system. Along with your fire alarm soft- ware you can store your test & inspection docu- ments, service records, manuals & AS built drawings for the system. Using a standard USB B connector it allows you to plug in with any standard S13 printer cable to upload or download information. The FDB is designed to hold critical manuals and documents with a durable steel retainer. It has designated hooks to organize key rings and hold important business cards for easy access and reference. Inside the cover it has a organized note table that allows for documentation for passwords and other critical system information. Standard Features: Installed with a 4 gig digital flash drive with USB B connector 2 Key ring hooks to hold system keys Business card holder for key contacts Overall Dimensions are 12" x 13" tal and 2 1/4 deep 16 gauge steel box and cover for security Durable powercoat baked on finish other colors available Standard 3h"cat 30 key lock other lock as- semblies available Solid stainless steel piano hinge Permanently screened white ink I" high "Fire Alarm Documents" Legend sheet for passwords and system information REG IRED NFPA COMPANY Made 4U7&A. I Space Age Electronics, Inc. 2009 ED0549 LT10559 Rev.D 1/2 Space Age Electronics, Inc. www.lsae.com 800.486.1723 Toll Free 508.485.0966 Local 508.485.4740 Fax No Excuses, Just Solutions! SPACE ACE ELECTRONICS, INC. o pecifications: The fire alarm documents box (FAD) shall be UL Listed, constructed of 18 gauge cold rolled steel. It shall have a red powder coat epoxy finish. The cover shall be permanently screened with 1" high lettering "FIRE ALARM DOCUMENTS" with white indelible ink. The access door shall be locked with a 3/4" barrel lock and the hinge shall be a solid width 12" stainless steel piano hinge. The enclosure will supply 4 mounting holes. Inside the enclosure will accommodate standard 8 1/2 x 11 manuals and loose document records that will be protected within the enclosure. A legend sheet will be permanently attached to the door for system required documentation, key contacts and system information. The FAD will have securely mounted inside a minimum of 4 Gigabyte digital flash memory drive with a standard USB B connector for uploading and downloading information. The drive shall not be accessible without tools to any person whom gains access to the records. The enclosure shall also provide 2 key ring holders with a location to mount standard business type cards for key contact personnel. USB Storage Interface Requires Standard USB-B Connector Property Infennatlon Minimum Rnquired 006anrentatlon (SIG-FUN) on.r.ov.%FP*422013&.7.ZI) an_d.c... Cadhticatl005 and Approvals — .o.. lit 1.1 Iaot Iota.. St. rot... rodvd 16.1 System1n01011d110n Contldcic. t.*.dnas,O bdNFPA.Iadfldt.aStfl scroroS.çovt.dIr...w.ott.vat.onoot..tv. on.. 110: ,ItgcOro,tod Idutoro., 0d. co.lcot litt..c.. I*O%flt 16.5 Authority doting J*#ndicllon: I 1S.ot000dfla0001dyaotaatol*alaltattho .11do.Mtta000000td.Oo,401111d100000tty dob.0110duoq..tdt.000da.M.Ithd not.o.01040 0nbro.ofl*ovrto.t. $CIt.%t1.I(MdI1.paS10oSO.thgL.At.*d0fl.Th1t80.dt&2 4.00 __________ 10 cOnlata, 3*1010.4 .1000.1000 .1* 74.001 731 1* Or As II pw,&.vw.t*oononn IrnMdoIn Equipment tnfor,n.tlnn As 70Od01(LAtn40o*t0. Or 0600 001___ scroll.. 0.5,711 1.1110614 7,01 Legend sheet for storing system informatioi including contacts, sign-off, maintenance test information, and alternate locations of additional records. Space Age Electronics, Inc. www.lsae.com 800.486.1723 Toll Free 508.485.0966 Local 508.485.4740 Fax Ordering Information: Part # Description S5U00685 Fire Alarm Storage Cabinet RED SSU00686 Custom screening with your Logo Check out our Infinity line eFAD single gang 2 Gig digital storage solutions (IAMEFAD) No Excuses, Just Solutions! This document is subject to change without notice, see doc # E00479 for legal disclaimer ED0549 LT10559 Rev.D 2/2 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL - FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7300-0553:0110 Page 1 of 1 CATEGORY: 7300-- FIRE ALARM CONTROL UNITACCESSORIES/MISC. DEVICES LISTEE: SPACE AGE ELECTRONICS58 Chockett Road, Sterling, MA 01564 Contact: Robert Scholl (508) 485-0966 Fax (508) 485-4740 Email: bobs@lsae.com DESIGN: Models TC2-32, TCI-18, TCX/A64, TCX/D 128, ACE/A, AC2, AQE/D, IF-2, IFI, IFX/A and IFXiD enclosures. Models ACE-11, ACE-12 and ACE-1 3 document cabinets. Refer to listee's data sheet for detailed product description and operational considerations. INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listees name, model number and UL label. APPROVAL: Listed as fire alarm equipment enclosures and document cabinets for use with listee's fire alarm equipment, Refer to listee's Installation Instruction Manual for details. 05-06-14 gt This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other 0 Date Issued: July 01, 2015 Listing Expires June 30, 2016 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division S S INTELLIGENT DUCT DETECTORS MIX-DH3000 SERIES Features Ll MIX-DH3000 Intelligent Ionization Duct Detector MIX-DH3100R Intelligent Photoelectric Duct Detector with Relay Description Mircom's MIX-DH3000 Series Intelligent Smoke Duct Detectors are the latest analog addressable innovation for early detection of smoke and products of combustion present in air moving through HVAC ducts in Commercial, Industrial, and Residential applications. The Duct Detectors are designed to prevent the recirculation or spread of smoke by air handling systems, fans, and blowers. Complete systems may be shut down via the building's fire alarm control panel (FACP) in the event of smoke detection. The MIX-DH3000 Series are Low-Flow Ionization and Photoelectric air duct smoke detectors that are capable of sensing smoke in air velocities from 100 to 4,000 feet per minute (0.5 to 20.32 m/sec). Low-flow technology can detect smoke at air speed velocities of 100 feet per minute or greater, while continuing the same reliable performance to 4,000 feet per minute. The MIX-DH3000 Series are designed and built to meet all local code requirements, as well as the NFPA and ICC standards regarding HVAC supply and return duct smoke detectors. Output terminals are provided for a remote alarm indicator accessory. Low-Flow Technology: Both Ionization and Photoelectric models listed for velocities between 100-4000 ft./min Both Ionization and Photoelectric models listed for high temperature applications Units supplied with slide-in MIX-ADD Address Card for easy device addressing Patent pending "No-Tools Required" front or rear loading and removing sampling/exhaust tubes Patent pending "Test Port Valve" allows for aerosol smoke testing without cover removal Clear cover fitted with four captive "No-Tools Required" thumbscrews Instantaneous cover removal trouble indication Vertical terminal block for easier wiring Steady red LED on detector head indicates alarm More wiring space than competitive models Footprint allows easy retrofit in many applications without additional drilling Duct wall gaskets on back of enclosure are pre- installed External mounting tabs do not require cover removal to install Colored cover gasket indicates proper cover seal Large terminal connection screws Alpha Series interchangeable "plug-in" UL268 photoelectric or ionization heads Advanced detector head design yields internal dust filtering No additional screens or filters to clean Compatible with FX-350 Fire Alarm Control Panels Complete wiring details permanently attached to unit MIX-DH3000R1M1X-DH3I00R (with relay Operating voltages: 24VAC or 24VDC In-line terminal block for easier wiring Remote accessories available Includes green pilot and red alarm visual indicators One set of 15A form "C" alarm contacts C®US 0 (MD(-DH3000R & MIX-0H3100R) S6295 3240-1477:154 (MIX-0H3 000 & MIX-0H3100) 1'A-rAI f%f ku IRI W #MIMLJ.J iuiviar 5685 NOT TO BE USED FOR INSTALLATION PURPOSES. Mircom reserves the right to make changes at any time without notice in prices, colours, materials, components, equipment, specifications and models and also to discontinue models. 0 MIX-DI3000/MIX-DH3I 00 Specifications I !] :IIIIII i:e ': Ki i'Dii — — — Series Intelligent ( D ) X Addressable -. Fire Alarm '/ L2 L2 Control Panel \(3 ,,J MIX-DH3000/MIX-DH3I00 MIX-DH3000/MIX-DH3100 Detector #1 Detector #X (+) FX-350 — — — Series Intelligent ( D ) ( o Addressable Fire Alarm ___________________ ( L2 L2 L2 L2 Control Panel 1 MIX-DH3000/MIX-DH3I00 MIX-DH3000/MIX-DI3100 (- Detector #1 Detector #X Terminal Connections Remote Accessory Wiring 6 -R }Remote Alarm Accessory 5 +R 4 ® L2 } FACP SLC (Loop) - 3 ® L2 2 ® LI }FACP SLC (Loop) + 1®LI Engineer Specifications BLACK RED ALARM LED Air duct smoke detectors shall be Mircom MIX-DH3000 Series. For ionization detectors the model number is MIX-DH3000. For photoelectric detectors the model number is MIX-DH3I00. The detectors shall be listed by Underwriters Laboratories per UL 268A. The detectors shall operate at air velocities from 100 feet per minute to 4,000 feet per minute and at temperatures of no greater than 140°F (60°C). Visual indication of alarm and power must be provided on the detector. Air handling unit shut down shall be accommodated via the associated FACP. Detector head shall not require additional filters or screens which must be maintained. The housing shall contain a detector base which will accept photoelectric or ionization detector heads as well as a means of detector addressing. Terminal connections shall be of the screw type, a minimum of #6 screw (#12 to #22 AWG compatible). Terminals shall be provided for remote alarm indication. All wiring must comply with local codes and regulations. A method of testing the alarm function with a magnet must be provided. A method of smoke testing the detector without removing the cover must be provided. All unit, remote accessory, and common function connection designations must be permanently affixed to the unit. Cover and sampling/exhaust tube installation or removal must not require the use of tools. Sample and exhaust tubes shall be capable of removal/installation from the front and/or rear of the detector for inspection/ maintenance. CAT. 5685 AA/2'. II i rconi NOT TO BE USED FOR INSTALLATION PURPOSES. page 2 of 4 ALARM CONTACT — SUPERVISED UNSUPERVISED 1A@30VDC I/4HP© 125/2SOVAC•(NC1 UL LISTED 113HP©125/2SOVAC.(NO) COMPATIBLE IACPSIC + + + + (LOOP) + IN OUT OUT OUT - + OUT TEST PILOT AIRN OUT IRBI ACI+ N/U I I I I I I NM! rly - T+ ...................!J \pusmsufla - ND A DTIO5!R C TEST SWEN NOT tio Iluow NOMLE LED TBI.. .................. RED AID AM BLACK ND . MIX.DH3000R SERIES MRTS-SERIES DUCT SMOKE DETECTOR REMOTE ACCESSORIES 9 Terminal Connections Remote Accessory Wiring LIII? C+ IT+IP+ I AL+lC -1 TB+ NCT CON TNO 24Y1N/O IACP REMOTE ALARM POWER SIC ACCESSORY RELAY 24AC/DC I MIX-DH3000RIMIX-DH3I0OR Specifications MIX-DH3000RIMlX-DH3I00R Class "B" Wiring Diagram Series Intelligent MIX-DH3000RI MIX-DH3000R/ Addressable MIX-DH31QOR MIX-DH3100R D D Detector #1 • Detector #X Fire Alarm Control Panel (- L2 — — — — — — — — — — L2 SE.IFI!] Wi!AiT1TI!] I Ii '.1 (+ ----------- Series MIXDAddressable D MDR31OOR D Detector #X Fire Alarm I Control Panel (-) L2 -------I-------L2 I Engineer Specifications Air duct smoke detectors shall be Mircom MIX-DH3000 Series. For ionization detectors the model number is MIX-3000R.For photoelectric detectors the model number is MIX-3100R. The detectors shall be listed by Underwriters Laboratories per UL 268A. The detectors shall operate at air velocities from 100 feet per minute to 4,000 feet per minute and at temperatures of no greater than 140°F (60°C). Visual indication of alarm and power must be provided on the detector front. A manual relay/test switch located on the front of the device shall be provided. Detector head shall not require additional filters or screens which must be maintained, and shall include both a standby and alarm visual indication. The housing shall contain a detector base which will accept photoelectric or ionization detector heads as well as a means of detector addressing. ° Terminal connections shall be of the screw type, a minimum of #6 screw (#12 to #22 AWG compatible). Terminals shall be provided for remote alarm indication. All wiring must comply with local codes and regulations. A method of smoke testing the detector without removing the cover must be provided. All unit, remote accessory, and common function connection designations must be permanently affixed to the unit. Cover and sampling/exhaust tube installation or removal must not require the use of tools. ° Sample and exhaust tubes shall be capable of removal/installation from the front and/or rear of the detector for inspection/ maintenance. CAT. 5685 1611111, IVI i rco ni NOT TO BE USED FOR INSTALLATION PURPOSES. page 3 of 4 Remote Accessories r - -- . [ ;. H " MS-PA MRTS-KAPR Electrical Specifications The MS-RA and MRTS-KAPR remote accessories are designed to be used with Mircom's Duct Smoke Detectors to provide visual indication on the detector as well as remote test/reset functions. The MS-RA provides an LED indicator while the MRTS- KAPR is equipped with LEDs and a test/reset switch. Enabling the"Test' switch on the MRTS-KAPR provides a local alarm indication on the duct detector but not at the fire alarm control panel. Both models are constructed of attractive, durable brushed stainless steel and mount on a standard single gang electrical badcbox. Power Requirements: Alarm LED 15mA © 24VDC Pilot LED 1 5m © 24VDC Dimensions: 41/2" (114.3mm)H x 2 %"(69.85mm)W Air Velocity 100 to 4,000 ft./min. Ambient Temperature MIX-DI-13000 32°F to 150°F (0°C to 66°C) MIX-DH300R MIX-DH3I oo 32°F to 140°F (0°C to 60°C) MIX-DH3100R Humidity 10% to 95% R.H. Non-Condensing/Non-Freezing Wring #12 to #22 AWG terminals Material Grey plastic backbox,clear plastic cover DImensions L-1 31/2" X H-4Y2" X D-2 Y4" Max. Not Weight MIX-DH3000 / MIX-DH31 00 2 lbs. MIX-DH3000R / MIX-DH31 OCR 21h lbs. Radioactive Eement For MIX-DH3000/MIX-DH3000R (Ionization) Americium 241; 0.9 Micro-Curie Do Not Expose to Corrosive Atmospheres Kardware 7" exhaust tube, sampling tube end cap, mounting template and mounting hardware included MIX-DH3000R1M1X-DH3I OOR Electrical Specifications Relay Contact Ratings . Resistive Load Inductive Load Alarm I set form C" rated at Contacts 15 Amps @125VAC 1/4 HP @ 125/250VAC (NC) 10 Amps @ 277VAC 1/3 HP © 125/250VAC (NO) 7 Amps © 30VDC Control Board Power Requirements (without accessories) Standby 24VAC 105 mA Alarm 24VAC 195 mA 24VDC 26 mA 24VDC 54 mA Ordering Information Model I Dsc$ptlon MlX-DH3000 Alpha Intelligent Ionization Low-Flow Duct Smoke Detector MIX-DH3000R Alpha Intelligent Ionization Low-Flow Duct Smoke Detector with relay MIX-DH3100 Alpha Intelligent Photoelectric Low-Flow Duct Smoke Detector MIX-DH31 OOR Alpha Intelligent Photoelectric Low-Flow Duct Smoke Detector with relay MSTN-1 .0 Sampling tube for 12" or less duct width MSTN-2.5 Sampling tube for 6" to 2.5' duct width MSTN-5.0 Sampling tube for 2.5' to 5.0' duct width MSTN-1 0.0 Sampling tube for 5.0' to 10.0' duct width MRTS-KAPR Remote Alarm LED (Red), Pilot LED (Green) and Key-Operated Test/Reset Switch on a Single Gang Plate MS-RA Remote Alarm LED (Red) on a Single Gang Stainless Steel Plate NOT TO BE USED FOR INSTALLATION PURPOSES. M A/h, ircom Canada 25 Interchange Way Vaughan, Ontario L4K 5W3 Telephone: (905) 660-4655 Fax: (905) 660-4113 Mb page: http://.mircom.com U.S.A. 4575 Witmer Industrial Estates Niagara Falls, NY 14305 Toll Free: (888) 660-4655 Fax Toll Free: (888) 660-4113 Email: mail@mircom.com ISO 9001:2008 REGISTERED CAT. 5685 Rev. 3 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 3240-1477:0153 Page 1 of 1 CATEGORY: 3240 -- DUCT SMOKE DETECTOR HOUSING/BASE LISTEE: MIRCOM TECHNOLOGIES, LTD.25 Interchange Way, Vaughan, Ontario L4K 5W3 Canada Contact: Mara Cherubin (888) 6604655 Ext: 3110 Fax (888) 660-4113 Email: mcherubin@mircom.com DESIGN: Models MIX-DH3000R and MIX-DH3I OUR 4-wire analog addressable duct smoke detector units. Units consist of an enclosure, electrical components, listed open area detector and sampling and exhaust tubes. Refer to listee's data sheet for additional detailed product description and operational considerations. RATING: 24Vdc INSTALLATION: In accordance with listee's printed installation instructions, applicable codes & ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating and UL label. APPROVAL: Listed as duct detectors for use with separately listed compatible fire alarm control units when installed in HVAC systems with air velocity between 100 and 4000 ft/mm. Refer to Manufacturer's Installation Manual for details. XLF: 3240-1004:0116 0 05-17-2007mt This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2015 Listing Expires June 30, 2016 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division ALPHA INTELLIGENT ADDRESSABLE DETECTORS MIX-3000 SERIES MIX-3000 MIX-3100 Ionization Smoke Detector Photoelectric Smoke Detector Features Low profile design For use with the FX-350 Series Fire Alarm Control Panels Fast response time Automatic addressing with the MIX-ADD card Variety of mounting bases Ease of installation Elegant, unobtrusive design Digital communications MIX-3200 MIX-3300 0 Mufti-Sensor Detector Thermal Detector Description Mircom's Alpha Series Intelligent Addressable Detectors are designed to meet a wide range of applications. The detector's address is set in its base providing a convenient and trouble free maintenance procedure. The detectors mount into a selection of base styles to accommodate installation requirements. Intelligent Ionization Smoke Detector (MIX-3000) The Ionization smoke detector incorporates a unique dual chamber design to respond quickly and dependably to a broad range of fires. The ionization detector is equipped with a red LED which flashes when the detector is polled and turns on steady when the detector goes into alarm. (UL Listed) Intelligent Photoelectric Smoke Detector (MIX-3100) The lntelliaent ohotoelectric smoke sensor utilizes Intelligent Multi-Sensor Detector (MIX-3200) The Intelligent Multi-Sensor Detector is a photoelectric smoke detector with a supplementary thermal sensor. The Multi-Sensor detector combines photoelectric smoke and thermal sensor values to provide enhanced detection performance and reduction of false alarms. Information from each sensing element is processed and conditioned by an on-board advanced technology ASIC and digitally transmitted to the FACP as a single analog value comprised of the combined responses from both the photoelectric smoke and thermal detection elements. Intelligent Thermal Detector (MIX-3300) The Intelligent Thermal Detector utilizes state of the art electronic temperature sense to provide fast and accurate temperature monitoring. The thermal detector features an adjustable termperature range that is configured from the FX-350 Series fire alarm control panel. a unique optical sensing chamber that is designed to sense smoke produced by a wide range of combustion sources. The photoelectric detector is equipped with a clear LED which flashes when S6295 S6965 the detector is polled and turns on steady when the 72711477138 (MIX-3000, MD(-3100 (MIX-3100 detector goes into alarm. . (MIX-3 000) 7272-1477:131 & MIX-3200) S6299 & MIX-3200) S7498 (MIX-3100) 7272-1477:142 (M!X-3300) (M!X-33020) (MIX-3200) 7270-1477:139 (M!X-3300) CATALOG NUMBER 5676 NOT TO BE USED FOR INSTALLATiON PURPOSES. Mircom reserves the right to make changes at any time without notice in prices, colours, materials, components, equipment, specifications and models and also to discontinue models. Standby Current 500 pA Alarm LED Current 34mA opsmung Temperdure Range 131°F to 194°F (55°C to 90°C) Standby Current 400 pA Alarm Current LEO 3.4 mA 9 0 MIX-ADD Address Card A unique, patented addressing method provides simple, user friendly and accurate identification of the detector location. A coded MIX-ADD card is inserted in the base. This can then be read by any Alpha Series detector once it is plugged in. Using this method, all the electronic components are in the detector but the location information is held in the base. The MIX-ADD card simplifies and speeds up installation and commissioning. Addressing errors during maintenance and service are eliminated. Specifications General Specifications Operating Voltage 16.28 VDC Communication Class A (Style D) or Class B (Style B) switch selectable Rtiative Humidity 0% to 95% (No condensation or icing) MIX-3000 Ionization Detector [Standby Current 500 pA Alarm Current LED 3.5 mA MIX-3100 Photoelectic Detector Operating Temperature ;i o°c to +70°C) HousinglCover Plate Finish White Polycarbonate MIX-3200 Multi-Sensor Detector Standby Current 500 pA Alarm Current LED 3.5 mA MIX-3300 Thermal Detector Ordering Information ModI Description MIX-3000 Intelligent Addressable Ionization Smoke Detector (UL Listed) MIX-3100 Intelligent Addressable Photoelectric Smoke Detector MIX-3200 Intelligent Addressable Multi-Sensor Detector MIX-3300 Intelligent Addressable Thermal Detector MIX-ADD Address Card for MIX-3000 Series Intelligent Detectors NOT TO BE USED FOR INSTALLATION PURPOSES. Alki- M i r c o m Canada 25 Interchange Way 41 Vaughan, Onta rio L4K 5W3 Telephone: (905) 660-4655 Fax: (905) 6604113 U.S.A. 4575 Witmer Industrial Estates Niagara Falls, NY 14305 Toll Free: (888) 660-4655 Fax Toll Free: (888) 660-4113 Distributed by: Web page: http://www.mircom.com Email: mail@mircom.com ISO 9001:2008 REGISTERED CAT. 5676 Rev. 1 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7272-1477:0131 Page 1 of 1 CATEGORY: 7272 SMOKE DETECTOR-SYSTEM TYPE-PHOTOELECTRIC LISTEE: MIRCOM TECHNOLOGIES, LTD.25 Interchange Way, Vaughan, Ontario L4K 5W3 Canada Contact: Mara Cherubin (888) 660-4655 Ext: 3110 Fax (888) 660-4113 Email: mcherubin@mircom.com DESIGN: Model MIX-3100 photoelectric smoke detector. Refer to listee's data sheet for additional detailed product description and operational considerations RATING: Electrical: 17 to 28 VDC, 5 to 9V protocol INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating, and UL label. APPROVAL: Listed as a photoelectric smoke detector for use with listee's separately listed compatable fire alarm control units and listed Models MIX-2000 Series detector bases (CSFM Listing No. 7300-1477:145). Refer to listee's Installation Instruction Manual for details. NOTE: The photoelectric type detectors are generally more effective at detecting slow, smoldering fires which smolder for hours before bursting into flames. Sources of these fires may include cigarettes burning in couches or bedding. The ionization type detectors are generally more effective at detecting fast, flaming fires that consume combustible materials rapidly and spread quickly. Sources of these fires may include paper burning in a waste container or a grease fire in the kitchen XLF: 7272-1394:0104 04-06-2005 This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2015 Listing Expires June 30, 2016 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division SYSTEM $ SENSOR Indoor Selectable= Output Strobes and Horn Strobes for Ceiling Applications SpectrkertO Advance audible visible notification products are rich with features guaranteed to cut installation times and maximize profits. SPKTRMert Features Plug-in design with minimal intrusion into the back box S Tamper-resistant construction Automatic selection of 12- or 24-volt operation at 15 and 15/75 candela Field-selectable candela settings on ceiling units: 15, 15/75, 30 75, 95, 110, 115, 135, 150, 177, and 185 Horn rated at 88+ dBA at 16 volts Rotary switch for horn tone and three volume selections Universal mounting plate for ceiling units Mounting plate shorting spring feature checks wiring continuity before device installation Electrically Compatible with legacy SpectrAlert devices Compatible with MDL3 sync module Listed for ceiling or wall mounting The SpectrAlert Advance series offers the most versatile and easy-to-use line of horns, strobes, and horn strobes in the industry. With white and red plastic housings, wall and ceiling mounting options, and plain and FIRE-printed devices, SpectrAlert Advance can meet virtually any application requirement. Like the entire SpectrAlert Advance product line, ceiling-mount strobes and horn strobes include a variety of features that increase their application versatility while simplifying installation. All devices feature a plug-in design with minimal intrusion into the back box, making installations fast and foolproof while virtually eliminating costly and time-consuming ground faults. To further simplify installation, SpectrAlert Advance utilizes a universal mounting plate so you can mount them to a wide array of back boxes. With an onboard shorting spring, installers can test wiring continuity before the device is installed. Installers can also easily adapt devices to a suit a wide range of application requirements using field-selectable candela settings, automatic selection of 12- or 24-volt operation, and a rotary switch for horn tones with three volume selections. Agency Listings SIGNALING @ . USTED <S> APPROVED MEA approved C 712516530186 (indoor strobes) 7125.16530168 (horn strobes. 54011 (chenes, horn strobes. horns) 3023572 MEA45205E chime strobes( S5512 (strobes) 7135-16530189 (horns, chimes) k'k1ir.iI-1irr Architect/Engineer Specifications General SpectrAlert Advance strobes and horn strobes shall mount to a standard 4 x 4 x 11/2-inch back box, 4-inch octagon back box, or double- gang back box. Two-wire products shall also mount to a single-gang 2 x 4 x 17/8-inch back box. A universal mounting plate shall be used for mounting ceiling and wall products. The notification appliance circuit wiring shall terminate at the universal mounting plate. Also, SpectrAlert Advance products, when used with the Sync.Circuif" Module accessory, shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts. When used with the Sync.Circuit Module, 12-volt-rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts; 24-volt-rated notification appliance ciicuit outputs shall operate between 16.5 and 33 volts. Indoor SpectrAlert Advance products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or full-wave rectified unfiltered power supply. Strobes and horn strobes shall have field-selectable candela settings including 15, 15/75, 30, 75, 95, 110, 115, 135, 150, 177, and 185. Strobe The strobe shall be a System Sensor SpectrAlert Advance Model ______ listed to UL 1971 and shall be approved for fire protective service. The strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe's entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system. Horn Strobe Combination The horn strobe shall be a System Sensor SpectrAlert Advance Model ______ listed to UL 1971 and UL 464 and shall be approved for fire protective service. The horn strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe's entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system. The horn shall have three audibility options and an option to switch between a temporal three pattern and a non-temporal (continuous) pattern. These options are set by a multiple position switch. On four-wire products, the strobe shall be powered independently of the sounder. The horn on horn strobe models shall operate on a coded or non-coded power supply. Synchronization Module The module shall be a System Sensor Sync.Circuit model MDL3 listed to UL 464 and shall be approved for fire protective service. The module shall synchronize SpectrAlert strobes at 1 Hz and horns at temporal three. Also, while operating the strobes, the module shall silence the horns on horn strobe models over a single pair of wires. The module shall mount to a 4 11/16 x 4 11/16 x 2 1/8-inch back box. The module shall also control two Style Y (class B) circuits or one Style Z (class A) circuit. The module shall synchronize multiple zones. Daisy chaining two or more synchronization modules together will synchronize all the zones they control. The module shall not operate on a coded power supply. Standard Operating Temperature 32°F to 120°F (0°C to 49°C) Humidity Range 10 to 93% non-condensing Strobe Flash Rate 1 flash per second Nominal Voltage Regulated 12 DC/FWR or regulated 24 DC/FWR1 Operating Voltage Range2 8 to 17.5 V (12 V nominal) or 16 to 33 V (24 V nominal) Operating Voltage Range (MDL3) 8.5 to 17.5V 02 V nominal) or 16.5 to 33 V (24V nominal) Input Terminal Wire Gauge 12 to 18 AWG Ceiling-Mount Dimensions (including lens) 6.8 diameter x 2.5" high (1173 mm diameter x 64 mm high) Ceiling-Mount Surface Mount Back Box Skirt Dimensions (SBBCR,SBBCW) 6.9 diameter x 3.4" high (175 mm diameter x 86 mm high) Notes: Full Wave Rectified (FWR) voltage is a non-regulated, time-varying power source that is used on some power supply and panel outputs. P, S, PC, and SC products will operate at 12 V nominal only for 15 and 15/75 Cd. AVOSIOIOI UL Current Draw Data . UL Max. Strobe Current Draw (mA RMS) 8-17.5 Volts 16-33 Volts Candela DC FWR DC FWR Standard Candela Range 15 123 128 66 71 15/75 142 148 77 81 30 NA NA 94 96 75 NA NA 158 153 95 NA NA 181 176 110 NA NA 202 195 115 NA NA 210 205 High 135 NA NA 228 207 Candela Range 150 NA NA 246 220 177 NA NA 281 251 185 NA NA 286 258 UL Max. Current Draw (mA RMS), 2-Wire Horn Strobe, Standard Candela Range (15-115 cd) 8-17.5 Volts 16-33 Volts DC Input 15 15/75 15 15175 30 75 95 110 115 Temporal High 137 147 79 90 107 176 194 212 218 Temporal Medium 132 144 69 80 97 157 182 201 210 Temporal Low 132 143 66 77 93 154 179 198 207 Non-Temporal High 141 152 91 100 116 176 201 221 229 Non-Temporal Medium 133 145 75 85 102 163 187 207 216 Non-Temporal Low 131 144 68 79 96 156 182 201 210 FWR Input Temporal High 136 155 88 97 112 168 190 210 218 Temporal Medium 129 152 78 88 103 160 184 202 206 Temporal Low 129 151 76 86 101 160 184 194 201 • Non-Temporal High 142 161 103 112 126 181 203 221 229 Non-Temporal Medium 134 155 85 95 110 166 189 208 216 Non-Temporal Low 132 154 80 90 105 161 184 202 211 111WMax. Current Drawzimi:i 1Candela 1; 31F!Ti 16-33 Volts 16-33 Volts DC Input 135 150 177 185 FWR Input 135 150 177 185 Temporal High 245 259 290 297 Temporal High 215 231 258 265 Temporal Medium 235 253 288 297 Temporal Medium 209 224 250 258 Temporal Low 232 251 282 292 Temporal Low 207 221 248 256 Non-Temporal High 255 270 303 309 Non-Temporal High 233 248 275 281 Non-Temporal Medium 242 259 293 299 Non-Temporal Medium 219 232 262 267 Non-Temporal Low 238 254 291 295 Non-Temporal Low 214 229 256 262 Horn Strobe Tones and Sound Output Data Horn Strobe Output (dBA) 8-17.5 16-33 24-Volt Nominal Switch Volts Volts Reverberant Anecholc Position Sound Pattern dB DC FWR DC FWR DC FWR DC FWR 1 Temporal High 78 78 84 84 88 88 99 98 2 Temporal Medium 74 74 80 80 86 86 96 96 3 Temporal Low 71 73 76 76 83 80 94 89 4 Non-Temporal High 82 82 88 88 93 92 100 100 5 Non-Temporal Medium 78 78 85 85 90 90 98 98 6 Non-Temporal Low 75 75 81 81 88 84 96 92 7t Coded High 82 82 88 88 93 92 101 101 8t Coded Medium 78 78 85 85 90 90 97 98 9t Coded Low 75 75 81 81 88 85 96 92 tSettings 7, 8, and 9 are not available on 2-wire horn strobes. AVDS1O1O1 C SpectrAlert Advance Dimensions LI Ceiling-mount horn strobes Ceiling back box surface mount back box SpectrAlert Advance Ordering Information Ceiling Horn Strobes Ceiling Strobes PC2R 2-Wire Horn Strobe, Standard Cd, Red SCR Strobe, Standard Cd, Red PC2R-P 2-Wire Horn Strobe, Standard Cd, Red, Plain SCRH Strobe, High Cd, Red (no "FIRE") marking PC2RH 2-Wire Horn Strobe, High Cd, Red PC2W 2-Wire Horn Strobe, Standard Cd, White PC2W-P 2-Wire Horn Strobe, Standard Cd, White, Plain (no "FIRE") marking PC2W-SP 2-Wire Horn Strobe, Standard Cd, White, "Fuego" marking PC2WH 2-Wire Horn Strobe, High Cd, White PC2WH-P 2-Wire Horn Strobe, High Cd, White, Plain (no "FIRE") marking PC2WH-SP 2-Wire Horn Strobe, High Cd, White, "Fuego" PC4R 4-Wire Horn Strobe, Standard Cd, Red PC4RH 4-Wire Horn Strobe, High Cd, Red PC4W 4-Wire Horn Strobe, Standard Cd, White SCW Strobe, Standard Cd, White SCW-P Strobe, Standard Cd, White, Plain (no "Fire") marking SCWH Strobe, High Cd, White Accessories SBBCR Surface Mount Back Box, Ceiling, Red SBBCW Surface Mount Back Box, Ceiling, White Notes: All -P models have a plain housing (no "FIRE" marking on cover) All -SP models have "FUEGO" marking on cover "Standard cd" refers to strobes that include 15, 15/75, 30, 75, 95, 110, and 115 candela settings. "High cd" refers to strobes that include 135, 150, 177, and 185 candela settings. YNTEM 02015 System Sensor. 3825 Ohio Avenue • St. Charles, IL 60174 Poductedocatanssbecrtochongeaithorsno5ce.vetsystemensso.corn for current product information. mcluetrg the latest version of this data sheet. S"EItJSOR Phone: 800-SENSOR2 • Fax: 630-377-6495 ' AVDS1O1O2 • 03/15 O SYSTEM $ SENSOR Indoor Selectable. Output Horns, Strobes, and Horn Strobes for Wall Applications SpectrA/erie Advance audible visible notification products are rich with features guaranteed to cut installation times and maximize profits. Features Plug-in design with minimal intrusion into the back box 40 • Tamper-resistant construction Automatic selection of 12- or 24-volt operation at 15 and 15/75 candela Field-selectable candela settings on wall units: 15, 15/75, 30, 75, 95, 110, 115, 135, 150, 177, and 185 Horn rated at 88+ dBA at 16 volts Rotary switch for horn tone and three volume selections Universal mounting plate for wall units Mounting plate shorting spring checks wiring continuity before device installation Electrically Compatible with legacy SpectrAlert devices Compatible with MDL3 sync module Listed for ceiling or wall mounting F I ,..5... - 1 SPECTFIert The SpectrAlert Advance series offers the most versatile and easy-to-use line of horns, strobes, and horn strobes in the industry. With white and rec plastic housings, wall and ceiling mounting options, and plain and FIRE-printed devices, SpectrAlert Advance can meet virtually any application requirement. Like the entire SpectrAlert Advance product line, wall-mount l--3rns, strobes, and horn strobes include a variety of features that increase their application vesaility while simplifying installation. All de'ices feature plug-in designs with minimal intrusion into the back bcx, making installations fast and foolproof while virtually eiiminatirg costly and time-consuming ground faults. To further simplify nstallation and protect devices from construction damage, SpectrAlert Advance utilizes a universal mounting Aate with an onboard shr:ing spring, so installers can test wiring continuity before the device is installed. Installers can also ea:3ly adapt devices to a suit a wide range of application requirements using field-selectable candela settings automatic selection o 12- or 24-volt operation, and a rotary switch for horn tones with tnree volume selections. Agency Listings - SIGNALING <S> USTED APPROVED S4011 (chimes, hero strobes, horns) 3023572 S5512 (strobes) MEA approved M6A452-05-E 0 7125-1653:186 (indoor strobes) 7125-1653:188 (horn strobes, chime strobes) 7135-1653:169 (horns, chimes) SpectrAlert Advance Specifications Arch itect/Engi neer Specifications General SpectrAlert Advance horns, strobes, and horn strobes shall mount to a standard 4 x 4 x 11/2-inch back box, 4-inch octagon back box, or double-gang back box. Two-wire products shall also mount to a single-gang 2 x 4 x 17,8-inch back box. A universal mounting plate shall be used for mounting ceiling and wall products. The notification appliance circuit wiring shall terminate at the universal mounting plate. Also, SpectrAlert Advance products, when used with the Sync.Circuit" Module accessory, shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts. When used with the Sync.Circuit Module, 12-volt-rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts; 24-volt-rated notification appliance circuit outputs shall operate between 16.5 and 33 volts. Indoor SpectrAlert Advance products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or full- wave rectified unfiltered power supply. Strobes and horn strobes shall have field-selectable candela settings including 15, 15/75, 30, 75, 95, 110, 115, 135, 150, 177, and 185. Strobe The strobe shall be a System Sensor SpectrAlert Advance Model ______ listed to UL 1971 and shall be approved for fire protective service. The strobe shall be wired as a primary signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe's entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system. Horn Strobe Combination The horn strobe shall be a System Sensor SpectrAlert Advance Model ______ listed to UL 1971 and UL 464 and shall be approved for fire protective service. The horn strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe's entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system. The horn shall have three audibility options and an option to switch between a temporal three pattern and a non-temporal (continuous) pattern. These options are set by a multiple position switch. On four-wire products, the strobe shall be powered independently of the sounder. The horn on horn strobe models shall operate on a coded or non-coded power supply. Synchronization Module The module shall be a System Sensor Sync.Circuit model MDL3 listed to UL 464 and shall be approved for fire protective service. The module shall synchronize SpectrAlert strobes at 1 Hz and horns at temporal three. Also, while operating the strobes, the module shall silence the horns on horn strobe models over a single pair of wires. The module shall mount to a 411/16 x 411/16 x 21,8-inch back box. The module shall also control two Style Y (class B) circuits or one Style Z (class A) circuit. The module shall synchronize multiple zones. Daisy chaining two or more synchronization modules together will synchronize all the zones they control. The module shall not operate on a coded power supply. Physical/Electrical Specifications Standard Operating Temperature 32°F to 120°F (0°C to 49°C) Humidity Range 10 to 93% non-condensing Strobe Flash Rate 1 flash per second Nominal Voltage Regulated 12 DC/FiA/R or regulated 24 DC/FiNR1 Operating Voltage Rang& 8 to 17.5 V (12 V nominal) or 16 to 33 V (24 V nominal) Operating Voltage Range MDL3 Sync Module 8.5 to 17.5 V (12 V nominal) or 16.5 to 33 V(24 V nominal) Input Terminal Wire Gauge 12 to 18 AWG Wall-Mount Dimensions (including lens) 5.6L x 4.7"W x 2.5'D (142 mm Lx 119 mm W x 64 mm D) Horn Dimensions 5.6"L x 4.7"W x 1.3D (142 mm Lx 119 mm x 33 mm D) Wall-MountTrim Ring Dimensions (sold as a 5 pack) (TR-HS) 5.7L x 4.8"W x 0.35'D (145 mm L x 122 mm W x 9 m 0) Notes: Full Wave Rectified (FWR) voltage is a non-regulated, time-varying power source that is used on some power supply and panel outputs. P, 5, PC, and SC products will operate at 12 V nominal only for 15 and 15/75 Cd. 0 UL Current Draw Data UL Max. Strobe Current Draw (mA RMS) 8-17.5 Volts 16-33 Volts 8-17.5 Volts 16-33 Volts Candela DC FWR DC FWR Standard 15 123 128 66 71 Candela 15/75 142 148 77 81 Range 30 NA NA 94 96 75 NA NA 158 153 95 NA NA 181 176 110 NA NA 202 195 115 NA NA 210 205 High 135 NA NA 228 207 Candela 150 NA NA 246 220 Range 177 NA NA 281 251 185 NA NA 286 258 Sound Pattern dB DC FWR DC FWR Temporal High 57 55 69 75 Temporal Medium 44 49 58 69 Temporal Low 38 44 44 48 Non-temporal High 57 56 69 75 Non-temporal Medium 42 50 60 69 Non-temporal Low 41 44 50 50 Coded High 57 55 69 75 Coded Medium 44 51 56 69 Coded Low 40 46 52 50 DC Input 8-17.5 Volts 15 15/75 15 15)75 30 16-33 Volts 75 95 110 115 Temporal High 137 147 79 90 107 176 194 212 218 Temporal Medium 132 144 69 80 97 157 182 201 210 Temporal Low 132 143 66 77 93 154 179 198 207 Non-Temporal High 141 152 91 100 116 176 201 221 229 Non-Temporal Medium 133 145 75 85 102 163 187 207 216 Non-Temporal Low 131 144 68 79 96 156 182 201 210 FWR Input Temporal High 136 155 88 97 112 168 190 210 218 Temporal Medium 129 152 78 88 103 160 184 202 206 Temporal Low 129 151 76 86 101 160 184 194 201 Non-Temporal High 142 161 103 112 126 181 203 221 229 Non-Temporal Medium 134 155 85 95 110 166 189 208 216 Non-Temporal Low 132 154 80 90 105 161 184 202 211 16-33 Volts 16-33 Volts DC Input 135 150 177 185 FWR Input 135 150 177 185 Temporal High 245 259 290 297 Temporal High 215 231 258 265 Temporal Medium 235 253 288 297 Temporal Medium 209 224 250 258 Temporal Low 232 251 282 292 Temporal Low 207 221 248 256 Non-Temporal High 255 270 303 309 Non-Temporal High 233 248 275 281 Non-Temporal Medium 242 259 293 299 Non-Temporal Medium 219 232 262 267 Non-Temporal Low 238 254 291 295 Non-Temporal Low 214 229 256 262 Horn Tones and Sound Output Data Horn and Horn Strobe Output (dBA) 8-17.5 16-33 24-Volt Nominal Switch Volts Volts Reverberant Anecholc Position Sound Pattern dB DC FWR DC FWR DC FWR DC FWR 1 Temporal High 78 78 84 84 88 88 99 98 2 Temporal Medium 75 75 80 80 86 86 96 96 3 Temporal Low 71 71 76 76 83 80 - 94 89 4 Non-Temporal High 82 82 88 88 93 - 92 100 100 5 Non Temporal Medium 78 78 85 85 90 90 98 98 6 Non-Temporal Low 73 74 81 81 88 84 96 92 7t Coded High 82 82 88 88 93 92 101 101 8t Coded Medium 78 78 85 85 90 90 97 98 9f Coded Low 74 75 81 81 88 85 96 92 Settings 7, 8, and 9 are not available on 2-wire horn strobes SpectrAlert Advance Dimensions .91 Wall-mount horn strobes SpectrAtert Advance Ordering Information Wall Horn Strobes P2R 2-Wire Horn Strobe, Standard Cd, Red P2R-P 2-Wire Horn Strobe, Standard Cd, Red, Plain P2R-SP 2-Wire Horn Strobe, Standard Cd, Red, "FUEGO" P2RH 2-Wire Horn Strobe, High Cd, Red P2RH-P 2-Wire Horn Strobe, High Cd, Red, Plain P2W 2-Wire Horn Strobe, Standard Cd, White P2W-P 2-Wire Horn Strobe, Standard Cd, White, Plain P2WH 2-Wire Horn Strobe, High Cd, White P2WH-P 2-Wire Horn Strobe, High Cd, White, Plain P4R 4-Wire Horn Strobe, Standard Cd, Red P4R-P 4-Wire Horn Strobe, Standard Cd, Red, Plain P4RH 4-Wire Horn Strobe, High Cd, Red P4W 4-Wire Horn Strobe, Standard Cd, White Wall Strobes SR Strobe, Standard Cd, Red SR-P Strobe, Standard Cd, Red, Plain SR-SP Strobe, Standard Cd, Red, "FUEGO" Wall Strobes (cont.) SRH Strobe, High Cd, Red SRH-P Strobe, High Cd, Red, Plain SRH-SP Strobe, High Cd, Red, "FUEGO" SW Strobe, Standard Cd, White SW-P Strobe, Standard Cd, White, Plain SWH Strobe, High Cd, White SWH-P Strobe, High Cd, White, Plain Horns HR Horn, Red HW Horn, White. Accessories TR-HS Trim Ring, Wall, Red SBBR Indoor Surface Mount Back Box, Red SBBW Indoor Surface Mount Back Box, White Notes: All -P models have a plain housing (no "FIRE" marking on cover) All -SP models have "FUEGO" marking on cover "Standard Cd" refers to strobes that include 15, 15/75, 30, 75, 95, 110, and 115 candela settings. "High Cd" refers to strobes that include 135, 150, 177, and 185 candela settings. 3825 Ohio Avenue • St. Charles, IL 60174 ©2014 System Sensor. for direst product informahon, including the West version of this data sheet. E1LSOR SYSTEM Phone: 800-SENSOR2 • Fax: 630-377-6495 ProductspecionsoubecttochangeVthoutnotroe.Vfotsystenrsenser.com www.systemsensor.com Avos10201 • 1/14 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7125-1653:0186 Page 1 of 1 CATEGORY: 7125 - FIRE ALARM DEVICES FOR THE HEARING IMPAIRED LISTEE: System Sensor, Unincorporated Div of Honeywell Int'l Inc.3825 Ohio Ave, St. Charles, IL 60174 Contact: Irish Linhart (630) 762-5025 Fax (630) 377-7245 Email: trish.linhart@systemsensor.com DESIGN: Synchronous type strobe lights, Models $R, SRH, SW, SW-CLR-ALERT, SWH, SCR, SCRH, SOW, SCW-CLR-ALERT and SOWH followed by the suffix -P, -SP, -P0, or none. Intended for indoor use mounted on the wall or the ceiling. Refer to listee's data sheet for additional detailed product description and operational considerations. RATING: 8-17.5 or 16-33 VDC/FWR Candela: 15, 15/75, 30, 75, 95, 110, 115, *135 *150 *177 *185w INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances, and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating and UL label. APPROVAL: Listed as strobe lights suitable for hearing impaired application when used with separately listed compatible fire alarm control units. Suitable for indoor use, wall or ceiling mounted. Refer to listee's Installation Instruction Manual for details. *Rev. 03-11-10fm This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2015 Listing Expires June 30, 2016 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL 9 FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7125-1653:0188 Page 1 of 1 CATEGORY: 7125 -- FIRE ALARM DEVICES FOR THE HEARING IMPAIRED LISTEE: System Sensor, Unincorporated Div of Honeywell Int'l Inc.3825 Ohio Ave, St. Charles, IL 60174 Contact: Trish Linhart (630) 762-5025 Fax (630) 377-7245 Email: trish.linhartsystemsensor.com DESIGN: Models CHSR and CHSW Chime/Strobes. Models P2R, P2W, P2RH and 132WH Horn/Strobes two-wire type, rectangular enclosure. Models PC2R, PC2W, PC2RH and PC2WH Horn/Strobes two-wire type, round enclosure Models 134R, P4W, P4RH and P4WH Horn/Strobes four-wire type, rectangular enclosure. Models PC4R, PC4W, PC4RH and PC4WH Horn/Strobes* four-wire type, round enclosure. All models are intended for indoor use only unless other wise indicated. Models may be followed by the suffix "K" indicating indoor or outdoor use, or may be followed by suffix "P' for plain housing with no lettering. UK suffix models are suitable for outdoor applications at temperatures from -40°F to +151°F (-40°C to +66°C) and are rated NEMA 4X when used with the System Sensor weather proof back boxes models SA-WBB (Wall), SA-WBBW (Wall), SA-WBBC (Ceiling) and *SA4NBBCW (Ceiling). Refer to listee's data sheet for additional detailed product description and operational considerations. RATING: Standard Horn/Strobes and Chime/Strobes 8- 17.5 or 16-33 VDC/FWR Hi CD Horn/Strobes 16-33 VDC/FWR INSTALLATION: . In accordance with listee's printed installation instructions, applicable codes and ordinances, and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating, and UL label. APPROVAL: Listed as *horn/strobes or chime/strobes suitable for signaling appliances and equipment for the hearing impaired applications when used with separately listed compatible fire alarm control units. Horn/strobes with -K suffix are suitable for indoor or outdoor use, ceiling or wall mount. Chime section is suitable for private mode and indoor use only. Horn/Strobes or chime/strobes* can generate the distinctive three-pulse audible Temporal Pattern Fire Alarm Evacuation Signal (for total evacuation) in accordance with NFPA 72, 2010 Edition. Refer to listee's Installation Instruction Manual for details. "Corrected 121511 bh This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2015 Listing Expires June 30, 2016 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division 72-110 NATIONAL FIRE ALARM AND SIGNALING CODE 18.5.5.2 Where low ceiling heights do not permit wall mount- ing at a minimum of 80 in. (2.03 m), wall mounted visible appliances shall be mounted within 6 in. (150 mm) of the ceiling. The room size covered by a strobe of a given value shall be reduced by twice the difference between the mini- mum mounting height of 80 in. (2.03 m) and the actual lower mounting height. 18.5.5.3* Visible appliances listed for mounting parallel to the floor shall be permitted to be located on the ceiling or sus- pended below the ceiling. 18.5.5.4* Spacing in Rooms. 18.5.5.4.1 Spacing shall be in accordance with either Table 18.5.5.4.1(a) and Figure 18.5.5.4.1 or Table 18.5.5.4.1(b). Table 18.5.5.4.1 (a) Room Spacing for Wall-Mounted Visible Appliances Maximum Room Size ft in Minimum Required Light Output [Effective Intensity (cd)] Four Lights per Room One Light (One Light per Room per Wall) 20x20 6.10x6.10 15 NA 28 x 28 8.53 x 8.53 30 NA 30 > 30 9.14 x 9.14 34 NA 40 x 40 12.2 x 12.2 60 15 45x45 13.7x13.7 75 19 50 x 50 15.2 x 15.2 94 30 54x54 16.5x16.5 110 30 55x55 16.8x16.8 115 30 60x60 18.3x18.3 135 30 63x63 19.2x19.2 150 37 68x68 20.7x20.7 177 43 70x70 21.3x21.3 184 60 80x80 24.4x24.4 240 60 90 x 90 27.4 x 27.4 304 95 100 100 30.5x30.5 375 95 110x110 33.5x33.5 455 135 120x120 36.6x36.6 540 135 130x130 39.6x39.6 635 185 NA: Not allowable 18.5.5.4.2 Visible notification appliances shall be installed in accordance with Table 18.5.5.4.1(a) or Table 18.5.5.4.1(b) us-ing one of the following: A single visible notification appliance. *Two groups of visible notification appliances, where visual appliances of each group are synchronized, in the same room or adjacent space within the field of view. This shall include synchronization of strobes operated by separat e systems. More than two visible notification appliances or groups of synchronized appliances in the same room or adjacent space within the field of view that flash in synchronization. 18.5.5.4.3 Room spacing in accordance with Table 18.5.5.4.1 (a) and Figure 18.5.5.4.1 for wall-mounted appli- ances shall be based on locating the visible notification appli- ance at the halfway distance of the wall. Table 18.5.5.4.1(b) Room Spacing for Ceiling-Mounted Visible Appliances Minimum Maximum Maximum Lens Required Room Size Height* Light Output (Effective Intensity); ft in ft in One Light (Cd) 20 x 20 6.1 x 6.1 10 3.0 15 30 x 30 9.1 x 9.1 10 3.0 30 40x40 12.2x12.2 10 3.0 60 44 x 44 13.4 x 13.4 10 3.0 75 20 x 20 6.1 x 6.1 20 6.1 30 30 x 30 9.1 x 9.1 20 6.1 45 44x44 13.4x13.4 20 6.1 75 46 x 46 14.0 x 14.0 20 6.1 80 20 x 20 6.1 x 6.1 30 9.1 55 30 x 30 9.1 x 9.1 30 9.1 75 50 x 50 15.2 x 15.2 30 9.1 95 53x53 16.2x16.2 30 9.1 110 55x55 16.8x16.8 30 9.1 115 59 x 59 18.0 x 18.0 30 9.1 135 63 x 63 19.2 x 19.2 30 9.1 150 68x68 20.7x20.7 30 9.1 177 70x70 21.3x21.3 30 9.1 185 *This does not preclude mounting lens at lower heights. 20f1 6.1 m) 30ft (9.1m) k 40f1 - (12.2 m) ft[50 5.2m) I 20 ft I (6.1 m) I I 30 ft I (9.1 M) 40 ft I (12.2m) I 50ft J4 (15.2m) FIGURE 18.5.5.4.1 Room Spacing for Wall-Mounted Visible Appliances. 2013 Edition