Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
5345 ARMADA DR; BLDG A; AS140224; Permit
City of Carlsbad Sprinkler Permit Permit No: AS140224 Job Address: 5345 ARMADA DR Permit Type: SPRINK Parcel No: 2110231700 Lot #: 0 Status: ISSUED Applied 8/22/2014 Approved: 9/4/2014 Reference No.: Issued: 9/4/2014 PC #: Inspector: Project Title: GIA BLDG A - PRE-ACTION INSTALLATION OF SINGLE- INTERLOCK PRE-ACTION FIRE SPRINKLER SYSTEMIN EXISTING 1ST FL IT/SERVER ROOM. Applicant: SCHMIDT FIRE PROTECTION CO INC 4760 MURPHY CANYON RD SAN DIEGO, CA 92123 858-279-6122 Owner: GEMOLOGICAL INSTITUTE OF AMER INC 5345 ARMADA DR CARLSBAD CA Fees ($) Add'I Fees ($) Total ($) Balance ($) 268 0 268 0 Gemologicafi Institute of America Building A IT Closet 5343 Armada Drive Carlsbad, CA 92008 SH-979 SUBMITTAL PACKAGE . PREACTION FIRE SPRINKLER SYSTEM HYDRAULIC CALCULATIONS MATERIALS CUT SHEETS CSFM LISTING CERTIFICATES PREPARED BY: PAUL MOFFAT SPECIAL HAZARDS PROJECT MANAGER SCHMIDT FIRE PROTECTION A5lo)4 ma SCHMIDT FIRE PROTECTION CO., INC. - 'I 4192 MURPHY CANYON ROAD, SAN ORGO,CA 92123Pik )21OHIfl FAX: MMM Schmidt Fire Protection 4760 Murphy Canyon Road San Diego, CA 92123 858-279-6122 Job Name Building : Building A 1St Floor IT Room Location 5345 Armada Drive, Carlsbad, CA 92009 System : I Contract SH-979 Data File : GIA IT Closet Preaction.WXF Computer Programs by Hydratec Inc. Route 111 Windham N.H. USA 03087 0 Schmidt Fire Protection Page Date Hydraulic Desian Information Sheet Na GIA Date - 060114 Loc ion - 5345 Armada Drive, Carlsbad, CA 92009 Building - Building A 1st Floor IT Room System No. - 1 Contractor - Schmidt Fire Protection Contract No. - SH-979 Calculated By - Paul Moffat Drawing No. - FP1 Construction: (x) Combustible ( ) Non-Combustible Ceiling Height - Occupancy - Light - IT/Data S (x) NFPA 13 (x) Lt. Haz. Ord.Haz.Gp. ( ) 1 ( ) 2 ( ) 3 ( ) Fx.Haz. Y ( ) NFPA 231 ( ) NFPA 231C ( ) Figure Curve S Other T Specific Ruling Made By Date E M Area of Sprinkler Operation - 420 System Type Sprinkler/Nozzle Density - .1 ( ) Wet Make Reliable D Area Per Sprinkler - 120 ( ) Dry Model F1FR E Elevation at Highest Outlet - 9.333 ( ) Deluge Size 1/2 S Hose Allowance - Inside - 100 (x) Preaction K-Factor 5.6 I Rack Sprinkler Allowance - ( ) Other Temp.Rat. G Hose Allowance - Outside - N Note Calculation Flow Required - 162.536 Press Required - 33.36 at SRC Summary C-Factor Used: 120 Overhead 150 Underground ,Water Flow Test: Pump Data: Tank or Reservoir: Date of Test - 032714 Cap. - T Time of Test - 10:00 am Rated Cap.- Elev.- E Static Press - 90 @ Press - R Residual Press - 82 Elev. - Well Flow - 1190 Proof Flow S Elevation - 3 U P Location - 5345 Armada Drive P L Source of Information - Carlsbad Fire Department Y C Commodity Class Location O Storage Fit. Area Aisle W. M Storage Method: Solid Piled Palletized % Rack M Single Row ( ) Conven. Pallet ( ) Auto. Storage ( ) Encap. S R ( ) Double Row ( ) Slave Pallet ( ) Solid Shelf ( ) Non T A ( ) Mult. Row ( ) Open Shelf O C R K Flue Spacing Clearance:Storage to Ceiling A Longitudinal Transverse G E Horizontal Barriers Provided: [1 Computer Programs by Hydratec Inc. Route 111 Windha m N . H . U S A 0 3 0 8 7 vVdtel oppiy uive It..,) Schmidt Fire Protection Page 2 Date City Water Supply: Demand: CI - Static Pressure : 90 DI - Elevation : 2.743 C2 - Residual Pressure: 82 D2 - System Flow : 62.536 C2 - Residual Flow : 1190 D2 - System Pressure : 33.360 Hose (Adj City) Hose ( Demand) : 100 D3 - System Demand : 162.536 Safety Margin : 56.439 150 140 130 p120 R11° E100 Cl S 9° I _______________ - _____________________ C2 S 80 -_.... _ U 70 101 ercent Under - R6° E5° 40 30 D _____ 20 -- ____ 10 200 400 600 800 1000 1200 1400 1600 1800 FLOW (N" 1.85) . . . Comouter Proarams by Hvdratec Inc. Route 111 Windham N.H. USA 03087 riwnys ustu Ouffiffidly Schmidt Fire Protection Page 3 Date Fitting Legend Abbrev. Name % % 1 1% 11/2 2 21/2 3 3% 4 5 6 8 10 12 14 16 18 20 24 E NFPA 13 90' Standard Elbow 1 2 2 3 4 5 6 7 8 10 12 14 18 22 27 35 40 45 50 61 Fsp Flow Switch Potter VSR Fitting generates a Fixed Loss Based on Flow G NFPA 13 Gate Valve 0 0 0 0 0 1 1 1 1 2 2 3 4 5 6 7 8 10 11 13 H 45'Grvd-Vic Elbow #ll 0 0 1 1.5 2 2 3 3 3.5 3.5 4.5 5 6.5 8.5 10 18 20 23 25 30 90' Grvd-Vic Elbow #10 0 0 2 3 4 3.5 6 5 8 7 8.5 10 13 17 20 23 25 33 36 40 J 90'Tee-Branch Gry Vic #20 0 0 4.5 6 8 8.5 10.8 13 17 16 21 25 33 41 50 65 78 88 98 120 S NFPA 13 Swing Check Valve 4 5 5 7 9 11 14 16 19 22 27 32 45 55 65 76 87 98 109 130 T NFPA 13 90' Flow thru Tee 3 4 5 6 8 10 12 15 17 20 25 30 35 50 60 71 81 91 101 121 Units Summary Diameter Units Length Units Flow Units Pressure Units Inches Feet US Gallons per Minute Pounds per Square Inch . . . Comouter Proorams by Hvdratec Inc. Route 111 Windham N.H. USA 03087 Pressure / Flow Summary - STANDARD Schmidt Fire Protection Page 4 Date Node Elevation K-Fact Pt Pn Flow Density Area Press No Actual Actual Req. w 1 9.333 5.6 7.0 na 14.82 0.1 3 9.333 5.6 7.34 na 15.17 0.1 5 9.333 5.6 7.87 na 15.71 0.1 7 9.333 5.6 9.04 na 16.84 0.1 2 11.5 6.56 na 4 11.5 7.16 na 6 11.5 7.74 na 8 11.5 9.02 na P1 11.5 12.18 na P2 2.0 23.02 na P3 10.5 19.93 na P4 26.083 16.76 na Al 23.5 18.34 na A2 23.5 18.34 na A3 23.5 18.34 na 131 24.833 17.77 na B2 24.833 17.77 na B3 24.833 17.77 na Cl 23.5 18.35 na C2 23.5 18.35 na C3 23.5 18.35 na C4 23.5 18.35 na CS 24.833 17.77 na C6 24.833 17.77 na C7 24.833 17.77 na C8 24.833 17.77 na C9 24.833 17.77 na CIO 24.833 17.77 na Cli 24.833 17.77 na 24.833 17.77 na Co 24.833 17.77 na 24.833 17.77 na Di 23.5 18.37 na D2 23.5 18.37 na D3 23.5 18.37 na D4 24.833 17.79 na D5 24.833 17.79 na D6 24.833 17.79 na D7 24.833 17.79 na D8 24.833 17.8 na D9 24.833 17.8 na D10 24.833 17.8 na Dli 24.833 17.8 na D12 24.833 17.8 na D13 24.833 17.8 na El 24.833 17.81 na TOR 24.83 17.81 na 100.0 BOR 0.5 29.37 na UGI -7.0 32.63 na BKFL -7.0 32.65 na UG2 -3.0 35.95 na SRC 3.0 33.36 na The maximum velocity is 9.86 and it occurs in the pipe between nodes 8 and P1 . Computer Programs by Hydratec Inc. Route 111 Windham N.H. USA 03087 120 7.0 120 7.0 120 7.0 120 7.0 Final Calculations - Hazen-Williams Schmidt Fire Protection Page 5 Date Hyd. Qa Dia. Fitting Pipe Pt Pt HcH or Ftng's Pe Pv Notes ****** Qt Pf/Ft Eqv. Ln. Total Pf Pn 1 14.82 1.049 2E 4.0 2.667 7.000 K Factor = 5.60 to 120.0 0.0 4.000 -0.939 2 14.82 0.0748 0.0 6.667 0.499 Vet = 5.50 0.0 14.82 6.560 K Factor = 5.79 3 15.17 1.049 1 2.0 2.667 7.341 K Factor = 5.60 to 120.0 IT 5.0 7.000 -0.939 4 15.17 0.0781 0.0 9.667 0.755 Vel = 5.63 0.0 15.17 7.157 KFactor = 5.67 5 15.71 1.049 1 2.0 2.667 7.870 K Factor = 5.60 to 120.0 IT 5.0 7.000 -0.939 6 15.71 0.0833 0.0 9.667 0.805 Vet = 5.83 0.0 15.71 7.736 KFactor= 5.65 7 16.84 1.049 IE 2.0 2.667 9.039 K Factor = 5.60 to 120.0 IT 5.0 7.000 -0.939 8 16.84 0.0948 0.0 9.667 0.916 Vet = 6.25 0.0 16.84 9.016 K Factor = 5.61 S 14.82 1.049 0.0 8.000 6.560 120.0 0.0 0.0 0.0 4 14.82 0.0746 0.0 8.000 0.597 Vet = 5.50 4 15.17 1.38 0.0 8.000 7.157 to 120.0 0.0 0.0 0.0 6 29.99 0.0724 0.0 8.000 0.579 Vet = 6.43 6 15.71 1.61 2E 8.0 9.167 7.736 to 120.0 0.0 8.000 0.0 8 45.7 0.0746 0.0 17.167 1.280 Vet = 7.20 8 16.84 1.61 ii 4.0 19.780 9.016 to 120.0 0.0 4.000 0.0 P1 62.54 0.1331 0.0 23.780 3.165 Vet = 9.86 P1 0.0 1.61 ii 4.0 9.500 12.181 to 120.0 is 9.0 41.000 4.114 P2 62.54 0.1331 lEgi 28.0 50.500 6.723 Vet = 9.86 P2 0.0 2.157 21 8.615 10.000 23.018 to 120.0 0.0 8.615 -3.681 P3 62.54 0.0320 0.0 18.615 0.596 Vel = 5.49 P3 0.0 2.157 31 12.922 88.080 19.933 to 120.0 1 10.461 23.383 -6.749 P4 62.54 0.0320 0.0 111.463 3.571 Vet = 5.49 P4 -35.20 2.157 2J 20.921 46.920 16.755 to 120.0 0.0 20.921 1.119 A3 27.34 0.0069 0.0 67.841 0.470 Vet = 2.40 0.0 27.34 18.344 KFactor = 6.38 I 35.20 2.635 2J 29.654 82.833 16.755 to 120.0 0.0 29.654 0.541 B3 35.2 0.0042 0.0 112.487 0.470 Vel = 2.07 Computer Programs by Hydratec Inc. Route 111 Windham N.H. USA 03087 Final Calculations - Hazen-Williams Schmidt Fire Protection Page 6 Date Hyd. Qa Die. Fitting Pipe Pt Pt "C" or Ftng's Pe Pv Notes ****** W Qt Pf/Ft Eqv. Ln. Total Pf Pn 0.0 35.20 17.766 K Factor = 8.35 Al -0.78 2.635 4J 59.307 130.417 18.344 to 120.0 0.0 59.307 -0.577 Bl -0.78 0.0 0.0 189.724 -0.001 Vet: 0.05 0.0 -0.78 17.766 K Factor = -0.19 A2 -0.96 2.635 0.0 130.042 18.344 to 120.0 0.0 0.0 -0.577 62 -0.96 0.0 0.0 130.042 -0.001 Vel = 0.06 0.0 -0.96 17.766 K Factor = -0.23 Al 0.78 6.357 0.0 11.667 18.344 to 120.0 0.0 0.0 0.0 A2 0.78 0.0 0.0 11.667 0.0 Vet = 0.01 A2 0.96 6.357 0.0 11.667 18.344 to 120.0 0.0 0.0 0.0 A3 1.74 0.0 0.0 11.667 0.0 Vel = 0.02 A3 27.33 6.357 IJ 31.433 21.625 18.344 to 120.0 0.0 31.433 0.0 29.07 0.0 0.0 53.058 0.002 Vel = 0.29 0.0 29.07 18.346 K Factor = 6.79 BI -0.78 6.357 0.0 11.667 17.766 to 120.0 0.0 0.0 0.0 B2 -0.78 0.0 0.0 11.667 0.0 Vet = 0.01 B2 -0.96 6.357 0.0 11.667 17.766 to 120.0 0.0 0.0 0.0 B3 -1.74 0.0 0.0 11.667 0.0 Vet: 0.02 B3 35.20 6.357 IJ 31.433 21.625 17.766 to 120.0 0.0 31.433 0.0 C13 33.46 0.0001 0.0 53.058 0.003 Vet = 0.34 0.0 33.46 17.769 K Factor: 7.94 Cl -5.01 6.357 0.0 1.042 18.346 to 120.0 0.0 0.0 0.0 C2 -5.01 0.0 0.0 1.042 0.0 Vet = 0.05 C2 29.07 6.357 0.0 10.083 18.346 to 120.0 0.0 0.0 0.0 C3 24.06 0.0001 0.0 10.083 0.001 Vet = 0.24 C3 4.96 6.357 0.0 11.667 18.347 to 120.0 0.0 0.0 0.0 C4 19.1 0.0 0.0 11.667 0.0 Vel = 0.19 C4 -4.94 6.357 2H 12.573 12.667 18.347 to 120.0 0.0 12.573 -0.577 0.0 0.0 25.240 0.0 VeI= 0.14 IUD 14.16 4.95 6.357 0.0 11.792 17.770 to 120.0 0.0 0.0 0.0 C6 9.21 0.0 0.0 11.792 0.0 Vet: 0.09 Computer Programs by Hydratec Inc. Route 111 Windham N.H. USA 03087 Final Calculations - Hazen-Williams Schmidt Fire Protection Page 7 Date Hyd. Qa Dia. Fitting Pipe Pt Pt 11C11 or Ftng's Pe Pv ***** Notes **** Qt Pt/Ft Eqv. Ln. Total Pf Pn C6 -4.97 6.357 0.0 12.000 17.770 to 120.0 0.0 0.0 0.0 Cl 4.24 0.0 0.0 12.000 0.0 Vel = 0.04 C7 -5.01 6.357 0.0 12.000 17.770 to 120.0 0.0 0.0 0.0 CB -0.77 0.0 0.0 12.000 0.0 Vel = 0.01 C8 -5.08 6.357 0.0 12.000 17.770 to 120.0 0.0 0.0 0.0 C9 -5.85 0.0 0.0 12.000 0.0 Vet = 0.06 C9 -5.16 6.357 0.0 12.000 17.770 to 120.0 0.0 0.0 0.0 CIO -11.01 0.0 0.0 12.000 0.0 Vel 0.11 CIO -5.29 6.357 0.0 12.000 17.770 to 120.0 0.0 0.0 0.0 Cli -16.3 0.0 0.0 12.000 0.0 Vel = 0.16 Cli -5.41 6.357 0.0 12.000 17.770 to 120.0 0.0 0.0 0.0 C12 -21.71 -0.0001 0.0 12.000 -0.001 Vel = 0.22 C12 -5.57 6.357 0.0 9.750 17.769 to 120.0 0.0 0.0 0.0 , -27.28 0.0 0.0 9.750 0.0 Vet = 0.28 33.46 6.357 0.0 2.250 17.769 to 120.0 0.0 0.0 0.0 C14 6.18 0.0 0.0 2.250 0.0 Vet = 0.06 0.0 6.18 17.769 KFactor = 1.47 Ci 5.01 2.635 4J 59.307 156.833 18.346 to 120.0 0.0 59.307 0.0 Dl 5.01 0.0001 0.0 216.140 0.025 Vet = 0.29 0.0 5.01 18.371 KFactor = 1.17 C3 4.97 2.635 4J 59.307 157.875 18.347 to 120.0 0.0 59.307 0.0 02 4.97 0.0001 0.0 217.182 0.024 Vet = 0.29 0.0 4.97 18.371 KFactor = 1.16 C4 4.93 2.635 4J 59.307 159.125 18.347 to 120.0 0.0 59.307 0.0 03 4.93 0.0001 0.0 218.432 0.024 Vet = 0.29 0.0 4.93 18.371 K Factor = 1.15 C5 4.95 2.635 4.1 59.307 157.792 17.770 to 120.0 0.0 59.307 0.0 D4 4.95 0.0001 0.0 217.099 0.024 Vet = 0.29 0.0 ' 4.95 17.794 KFactor= 1.17 4.97 2.635 4J 59.307 158.125 17.770 to 120.0 0.0 59.307 0.0 05 4.97 0.0001 0.0 217.432 0.024 VeI= 0.29 Computer Programs by Hydratec Inc. Route 111 Windham N.H. USA 03087 Final Calculations - Hazen-Williams Schmidt Fire Protection Page 8 Date Hyd. Qa Dia. Fitting Pipe Pt Pt or Ftng's Pe Pv Notes 40 Qt P1/Ft Eqv. Ln. Total P1 Pn 0.0 4.97 17.794 KFactor = 1.18 C7 5.01 2.635 4J 59.307 157142 17.770 to 120.0 0.0 59.307 0.0 06 5.01 0.0001 0.0 216.849 0.024 Vel= 0.29 0.0 - 5.01 17.794 KFactor = 1.19 C8 5.08 2.635 4J 59.307 157.042 17.770 to 120.0 0.0 59.307 0.0 D7 5.08 0.0001 0.0 216.349 0.025 Vet = 0.30 0.0 5.08 17.795 KFactor 1.20 C9 5.16 2.635 4J 59.307 156.292 17.770 to 120.0 0.0 59.307 0.0 D8 5.16 0.0001 0.0 215.599 0.026 Vel = 0.30 0.0 5.16 17.796 KFactor 1.22 CIO 5.28 2.635 4J 59.307 154.917 17.770 to 120.0 0.0 59.307 0.0 D9 5.28 0.0001 0.0 214.224 0.026 Vel = 0.31 IV 0.0 5.28 17.796 K Factor = 1.25 CII 5.41 2.635 4J 59.307 155.250 17.770 to 120.0 0.0 59.307 0.0 010 5.41 0.0001 0.0 214.557 0.028 Vet = 0.32 0.0 5.41 17.798 K Factor = 1.28 C12 5.58 2.635 4J 59.307 155.625 17.769 to 120.0 0.0 59.307 0.0 DII 5.58 0.0001 0.0 214.932 0.030 Vel= 0.33 0.0 5.58 17.799 K Factor = 1.32 C14 6.18 2.635 4J 59.307 156.000 17.769 to 120.0 0.0 59.307 0.0 D13 6.18 0.0002 0.0 215.307 0.036 Vel = 0.36 0.0 6.18 17.805 KFactor = 1.46 Dl 5.01 6.357 0.0 11.667 18.371 to 120.0 0.0 0.0 0.0 D2 5.01 0.0 0.0 11.667 0.0 Vel = 0.05 D2 4.97 6.357 0.0 11.667 18.371 to 120.0 0.0 0.0 0.0 03 9.98 0.0 0.0 11.667 0.0 Vel = 0.10 03 4.93 6.357 2H 12.573 12.667 18.371 0.0 12.573 -0.577 4 120.0 14.91 0.0 0.0 25.240 0.0 Vet = 0.15 D4 4.95 6.357 0.0 11.792 17.794 to 120.0 0.0 0.0 0.0 D5 19.86 0.0 0.0 11.792 0.0 Vet = 0.20 Computer Programs by Hydratec Inc. Route 111 Windham N.H. USA 03087 Final Calculations - Hazen-Williams Schmidt Fire Protection Page 9 Date Hyd. Qa Dia. Fitting Pipe Pt Pt S UCH or Ftng's Pe Pv Notes Qt Pf/Ft Eqv. Ln. Total Pf Pn 05 4.97 6.357 0.0 12.000 17.794 to 120.0 0.0 0.0 0.0 D6 24.83 0.0 0.0 12.000 0.0 Vel= 0.25 D6 5.02 6.357 0.0 12.000 17.794 to 120.0 0.0 0.0 0.0 07 29.85 0.0001 0.0 12.000 0.001 Vel = 0.30 - 07 5.07 6.357 0.0 12.000 17.795 to 120.0 0.0 0.0 0.0 08 3492 0.0001 0.0 12.000 0.001 = _Vel 0.35 08 5.17 6.357 0.0 12.000 17.796 to 120.0 0.0 0.0 0.0 D9 40.09 0.0 0.0 12.000 0.0 Vel = 0.41 09 5.28 6.357 0.0 12.000 17.796 to 120.0 0.0 0.0 0.0 010 45.37 0.0002 0.0 12.000 0.002 Vel = 0.46 010 5.41 6.357 0.0 12.000 17.798 to 120.0 0.0 0.0 0.0 DII 50.78 0.0001 0.0 12.000 0.001 Vel = 0.51 DII 5.58 6.357 IJ 31.433 9.750 17.799 to 120.0 0.0 31.433 0.0 . 56.36 0.0001 0.0 41.183 0.006 Vet= 0.57 0.0 6.357 0.0 2.250 17.805 to 120.0 0.0 0.0 0.0 013 56.36 0.0 0.0 2.250 0.0 Vel= 0.57 013 6.18 8.249 IJ 38.759 37.708 17.805 to 120.0 0.0 38.759 0.0 El 62.54 0.0 0.0 76.467 0.003 Vel = 0.38 El 0.0 8.249 II 15.269 6.417 17.808 to 120.0 0.0 15.269 0.001 TOR 6254 0.0001 0.0 21.686 0.002 Vel = 0.38 TOR 100.00 8.249 lFsp 0.0 24.330 17.811 Qa = 100 to 120.0 IS 52.853 57.551 11.537 * Fixed loss ....1 BOR 162.54 0.0003 IG 4.698 81.881 0.022 Vel = 0.98 BOR 0.0 8.27 31 61.681 12.500 29.370 to 140.0 0.0 61.681 3.248 UGI 162.54 0.0002 0.0 74.181 0.016 VeI= 0.97 UGI 0.0 8.044 21 40.821 38.000 32.634 to 150.0 IG 6.28 47.102 0.0 BKFL 162.54 0.0002 0.0 85.102 0.017 Vel = 1.03 BKFL 0.0 8.044 41 81.643 77.000 32.651 to 150.0 0.0 81.642 3.268 * Fixed loss = 5 UG2 162.54 0.0002 0.0 158.642 0.032 Vel = 1.03 UG2 0.0 11.734 II 27.788 143.000 35.951 to 150.0 IJ 69.47 97.258 -2.599 SRC 162.54 0.0 0.0 240.258 0.008 Vel = 0.48 O 0.0 162.54 33.360 KFactor 28.14 Computer Programs by Hydratec Inc. Route Ill Windham N.H. USA 03087 Carlsbad Municipal Water District Potable Water Discharge Event Report Date: ---- n 3 - P-1- -/ --- Location: Reason for Discharge Event: --------------------------------------- Type of Event Initial Dewatering Water Mains Note: Includes flow testing and flushing Dewateiing Water Mains Unscheduled Water Discharge ..Lk Clear flow path of debris, surface contaminants and/or hazardous materials. Do not remove native vegetation.. Erosion control, i.e.. sandbags, silt fencing, hay bales, gravel bags, decreasing the velocity of discharged water. Estimated Discharge Flow: JL'E?O GPM Start Time _JY ,SO End Time 0,46 Pre-Dechiorination Residual: Post-Dechlorination Residual: ...0 (Less than 0.1 mglL) PH within limits of 6.0 and 9.0 Upon completion of dewatering, ensure that the flow path is free of all temporary erosion prevention materials. NlAr Upon completion of dewatering, ensure that any sediments or silted areas are cleared. Water Sampling Performed by: - Comments: Submitted by: Reviewed by: (Name & Date) (Name & Date) Flow lest Record S T.Uyi:it. Location .T3T -or% Hydrant 11) No. S r'g' Size Main 1%" Static . Residuat . Pressure Drop.. ___,(PDT 1) K factor for PDT 1 3.Ot Flow Hydrant(s) Hydrant 1 location Hydrant 2 location Hydrant 3 location Hydrant I Pitot Hydrant 2 Pitot Hydrant 3 Pitot Psi: Psi Psi GPM: lk°01 GPM:_______ GPM:_______ TotaL %0 b fiVI \ Size of Orifice -' l-.• Size of Orifice___________ Size of Orifice. Calculated test and flow data - 0 x PD2 k = Q2 PDI*k Static:...................... Desired Residual.......20 Pressure Drop (PD 2).. 'rO K factor PD 2: 9. .9 - 1 16% o x 9 . -divided by '3 .''- equals _qc2.'GPM at 20 psi residual Q P02k PD 1k Q2 Comments: Test conducted conducted for: Conducted by:V-t-i_ Q L(7.4 •:;h.. Date: "..4 Time: tc tqC0 /Fire & BuildinIV I Products Technical Services: Tel: (800) 381-9312/ Fax: (800) 791-5500 Preaction System with Model DV-5 Deluge Valve Single Interlock, Supervised - Electric Actuation 1-1/2 thru 8 Inch (DN40 thru DN200) General Description The Model DV-5 Supervised Single In- terlock Preaction System with Electric Actuation (Fig. 1) utilizes automatic sprinklers and a supplemental detec- tion system. The supplemental detec- tion system is typically comprised of 24 VDC heat detectors, smoke detec- tors, manual pull stations, etc. Actua- tion of the detection system automat- ically operates (releases) the Model DV-5 Deluge Valve, allowing water to flow into the sprinkler piping system and to be discharged from any sprin- klers that may be open. In accordance with the requirements of the National Fire Protection Asso- ciation, a preaction system employing more than 20 automatic sprinklers is to have the sprinkler piping automatically supervised to monitor the overall in- tegrity of the system. In the case of a Supervised Single Interlock Preaction System, a Riser Check Valve (that does not require the use of priming water) provides an air check so that the system can be automatically pres- surized with a nominal supervisory air or nitrogen pressure of 10 psi (0,69 bar). A supervisory low pressure alarm switch that is set to transfer its contacts at nominally 5 psi (0,34 bar), on de- creasing pressure, is utilized to indi- cate whether there are any abnormal leaks in the sprinkler system piping. Loss of air pressure from the system as a result of a damaged sprinkler or broken piping will not cause the DV-5 Valve to open - the air pressure is for supervisory alarm only. Typically, the system designer selects the detection components for a single interlock preaction system that will re- spond to a fire sooner than the auto- matic sprinklers. Consequently, the system will experience a minimal delay in water delivery over that for a wet pipe sprinkler system because the Page 1 of 14 system will have begun to fill with water before a sprinkler operates. Supervised single interlock preaction systems are generally used to protect areas where there is danger of serious water damage that might result from damaged automatic sprinklers or pip- ing. Typically, such areas include com- puter rooms, storage areas for valu- able artifacts, libraries, and archives. Single interlock preaction systems are also effectively used to protect proper- ties where a pre-alarm of a possible fire condition may allow time for fire SEPTEMBER, 2004 extinguishment by alternate suppres- sion means, prior to a sprinkler dis- charge. In the event the fire cannot otherwise be extinguished, the preac- tion sprinkler system will then perform as the primary fire protection system. The Model DV-5 Deluge Valve (de- scribed in Technical Data Sheet TFP1305) is a diaphragm style valve that depends upon water pressure in the Diaphragm Chamber to hold the Diaphragm closed against the water supply pressure. When the DV-5 Valve is set for service, the Diaphragm (TEXT CONTINUED ON PAGE 9) TFPI42O S Page 2 of 14 TFPI42O C 0 1 - Model DV-5 Deluge Valve 2 - Main Control Valve (NO,) 3 - Diaphragm Chamber Supply Control Valve (N.O.) 4 - Local Manual Control Station 5 - Automatic Sprinklers 6 - Heat Detectors, Smoke Detectors, etc. (Fire Detection) 7 - Water Supply Pressure Gauge 8 - Diaphragm Chamber Pressure Gauge 9 - System Drain Valve (NC.) 10 - Main Drain Valve (N.C.) (Shown at Rear of Valve) 11 - Diaphragm Chamber Automatic Shut-Oft Valve Waterfiow Pressure Alarm Switch (Shown at Rear of Valve) Water Motor Alarm (Optional) Solenoid Valve Deluge Valve Releasing Panel Riser Check Valve Supervisory Air Pressure Gauge Automatic Supervisory Air/Nitrogen Supply Supervisory Low Pressure Alarm Switch FIGURE 1— PART IOF2 S SUPERVISED SINGLE INTERLOCK PREACTION SYSTEM WITH ELECTRIC ACTUATION - SYSTEM SCHEMATIC (Front View) - fl C TFPI420 Page 3of 14 1 - Model DV-5 Deluge Valve 2 - Main Control Valve (N.O.) 3 - Diaphragm Chamber Supply Control Valve (N.0) 4 - Local Manual Control Station (Shown at Front of Valve) 5 - Automatic Sprinklers 6 - Heat Detectors, Smoke Detectors, etc. (Fire Detection) 7 Water Supply Pressure Gauge (Shown at Front of Valve) Ii 8 - Diaphragm Chamber Pressure Gauge (Shown at Front of Valve) 9 System Drain Valve (N.C.) 10- Main Drain Valve (N.C.) 11 - Diaphragm Chamber Automatic Shut-Off Valve Waterfiow Pressure Alarm Switch Water Motor Alarm (Optional) Solenoid Valve 15 Deluge Valve Releasing Panel Riser Check Valve Supervisory Air Pressure Gauge (Shown at Front of Valve) Automatic Supervisory Air/Nitrogen Supply Supervisory Low Pressure Alarm Switch FIGURE — PART 2OF2 S SUPERVISED SINGLE INTERLOCK PREACTION SYSTEM WITH ELECTRIC ACTUATION - SYSTEM SCHEMATIC (Rear View) - NO. DESCRIPTION QTY. P/N 19 1/4' Plug .............. 1 CH 20 3/4° Plug ............. .1 CH 21 1/2' Union ............5 CM 22 3/4° Union ............1 CM 23 114' 90' Elbow . ........ I CM 24 1/2'901 Elbow .........7 Cl-I 25 314'90' Elbow .........1 CH 26 3/4° x 1/2° 90° Elbow ....1 CM 27 1/2' Tee ..............3 CM 28 1/2'xl/4°xl/2'Tee ....3 CM 29 314' Tee ..............1 CM 30 314°x112"x314"Tee ....2 CM 31 1/4' x Close Nipple .....2 OH 32 10 x Close Nipple .....3 CM 33 1/2'x1-112° Nipple .....11 CM 34 1/2' x 2' Nipple ........1 CM 35 1/2' x2-1/2' Nipple .....3 CH 36 1/2° x 5° Nipple ........2 CM 37 112' x 7" Nipple ........1 CM 38 Select Nipple per Table .2 CH 39 Select Nipple per Table .2 CM 40 3/4'x 1-1/2' Nipple .....6 CM 41 3/4'x2' Nipple ........I OH 42 3/4° x 4° Nipple .........1 CM P4 7 Page 4 of 14 TFPI42O S S P11 - pio P3 PI P16 P16 P16 P~ P16 Pg 15 401 (GREEN 16 ,A11 P2'-" 26 P17 1 P19 271 29 Ps P14 12 40 _.1 22 P8 13— NO, DESCRIPTION OTY. P/N 1 300 psi/ 2000 cPa Water Pressure Gauge .2 92-343-1-005 2 1/4' Gauge Test Valve 1 46-005-1-002 3 Model MC-1 Manual Control Station ........ .I 52-289-2-001 4 Model AD-i Automatic Drain Valve ...........1 52-793-2-004 5 Automatic Shut-Off Valve, Model ASV-1 ..........1 92-343-1-021 S Waterilow Pressure Alarm Switch (PS10-2A) .1 2571 7 1/2' Ball Valve .........2 48-050-1-004 8 1/2' Spring Loaded Check Valve ..........1 92-322-1-002 9 1/2' V-Strainer .........1 52-353-1-005 10 3/4° Swing Check Valve .1 46-049-1-005 11 3/4° Angle Valve .......1 46-048-1-005 12 Drip Funnel Connector 1 92-211-1-005 13 Drip Funnel Bracket 1 92-211-1-003 14 Drip Funnel ...........1 92-343-1-007 1$ 3/32' Vent Fitting .......1 92-032-1-002 16 114' x 18lubing .......1 OH ii 1/2'Tubing Connector 1 OH 18 1/2'x12Tubing .......1 CM 28 30 20 35 LOCATION FQ} OPTIONAL ELECTFIICAU.Y1"~4 1 I I I SUPERVISED I :33 I N.O. ALARM I I CONTROL VALVE! 24 NOTES: Supervised Single Interlock Preaction Trim with Electric Actuation is comprised of Items 1-42 plus Items P1-P19 and Items El .E4. Use only the 2' Model CV-1 FR Riser Check Valve for 1-1/2 or 2" assemblies. All Fittings and Nipples are galvanized (Standard Order). CM: Common Hardware. NO. DESCRIPTION OTY PIN P1 250 psi/ 1750 kPa Air Pressure Gauge .1 92-343-1-012 P2 1/4° Gauge Test Valve . .1 46-005-1-002 P3 Low Air Pressure Alarm Switch (PS10-2A) ......1 2571 P4 1/4" Pressure Relief Valve ................1 92-343-1-019 PS 1/2" Swing Check Valve .1 46-049-1-004 P6 1/2 Globe Valve .......1 46-047-1-004 P7 3/4" Angle Valve .......1 46-048-1-007 P8 1/4" Plug.... .......... 3 CM P9 1/2" a 1/4" Reducing Bushing ..............1 CH P10 1/2° Union ............1 CM P11 1/2" 90° Elbow .........1 Cl-I P12 1/2" Cross ............1 Cl-i P131/2"x1/2"x114°Tee ....1 CM P14 1°x3/4'0/2"Tee .....1 CM P15 IX 'x 3' Nipple ........1 Ct-I P16 112"x 1-112' Nipple .....5 Cl-I P17 112" a 2-1/2' Nipple .....1 CM P18 3/4"x1-112' Nipple .....1 CH P19 1°x2" Nipple-- I CM El Solenoid Valve Per Data Ordered SheelTFP2180 .......1 Separately E2 1/2" Tubing Connecter . 1 CM 53 112" a 24"7 ubing .......1 CM 54 '1/2's 1-1/2' Nipple ......1 CM El (ORDERED SEPARATELY) 14 E2 E4 33 36 21 27 24 39 RISER CHECK 33 32 VALVE 33 28 (NOTE 2) 33 37 3 21 9 34 32 33 24 17 24 NOTES 21 33 5. See Figure 2 of TFP1305 for Deluge Valve Port identification. 6. Route all Tubing 10 Drip Funnel, Item 14. P13 ( P16 P6 Select Appropriate Nipple Sizes Nipple per DV-5 Deluge Valve Size Number 1-1/2°(DN40) 2'(DNSO) 38 I 112"xClose I 1121 x2" 33 I 39 1 1/2° a 5° I '1/2° a 5-1/2 FIGURE 2A —PART 1 0F3 1-1/2 and 2 INCH (DN40 and DN50) MODEL DV-5 DELUGE VALVES SUPERVISED SINGLE INTERLOCK PREACTION WITH ELECTRIC ACTUATION TRIM (52-478-'X-119) 0 - EXPLODED VIEW— TFPI42O Page 5 of 14 33 NO. DESCRIPTION QTY. Pi1l I 300 psi/ 2000 kPa Water Pressure Gauge . . 2 92-343-1-005 2 1/4" Gauge Test Valve . .1 46-005-1-002 3 Model MC-1 Manual Control Station .........1 52-289-2-001 4 Model AD-i Automatic Drain Valve ...........1 52-793-2-004 5 Automatic Shut-Oft Valve, Model ASV-1 ..........1 92-343-1-021 6 Waterflow Pressure Alarm Switch (PS10-2A) .1 2571 7 10 Ball Valve .........2 46-050-1-004 iS 1/2° Spring Loaded Check Valve ..........1 92-322-1-002 52-353-1-005 9 10 1/2' V-Strainer .........1 3/4° Swing Check Valve .1 46-049-1-005 11 1-1/4' Angle Valve ......1 46-048-1-007 12 Drip Funnel Connector .. 1 92.211-1-005 13 Drip Funnel Bracket .... 1 92-211-1-003 14 Drip Funnel ............1 92-343.1-007 15 3/32' Vent Fitting .......1 92-032-1-002 16 19'x 18° Tubing - ---- --1 OH 17 1/2° Tubing Connector . . 1 OH NO. DESCRIPTION QTY. P/N 18 1/2'x 18' Tubing .......1 OH 19 114* Plug . .... ........ I Cl-I 20 '4' Plug .............1 OH 21 1/2°Union ............5 CH 22 314* Union ............1 CH 23 1/4' 90° Elbow .........1 CH 24 112° 90' Elbow.. . ..... . 7 OH 25 3/4° x 1/2" 900 Elbow 1 CH 26 1-1/4" 90° Elbow .......1 OH 27 1/2'lee ..............3 CH 28 1' x 1/4 x 1/2 Tee ....3 OH 29 3/4'Tee --- - - - -------- I CH 30 3(4x1/23/4°Tee ....2 CH 31 IN x Close Nipple .....2 CH 32 1/2°x Close Nipple .....2 OH 33 1/2x 1-1/2° Nipple ......13 ON 34 1/2"x2-1/2' Nipple . . . . . I OH 35 1P2'x3-112' Nipple .....1 CH 36 lP2x4°'Nippte ........1 CH 37 1/2° x 4-1/2' Nipple 1 CH P16 NO, DESCRIPTION QTY, P/N 38 1/2' x 5° Nipple ........1 OH 39 1/2"x5-l/2" Nipple .....1 OH 40 1/2 x 7" Nipple ........2 OH 41 3/4' x 1-1/2" Nipple .....5 OH 42 3/4' x2" Nipple ........1 CH 43 1-1/4'x2° Nipple ....... 1 OH 44 1-114°s4'Nipple .......1 CH P1 250 psi/ 1750 kPa Air Pressure Gauge .....1 92-343-1-012 P2 114' Gauge Test Valve .. 1 46-005-1-002 P3 Low Air Pressure Alarm Switch (PS10-2A) ......1 2571 P4 1/4 Pressure Relief Valve ................1 92-343-1-019 P5 1/2 Swing Check Valve .1 46-049-1-004 P6 1/2 Globe Valve .......1 46-047-1-004 P7 1-1/4' Angle Valve ......1 46-048-1-007 P8 1/4° Plug..............3 CH P9 1/2 x 1(4° Reducing Bushing ..............1 OH PlO 1/2' Union .............1 OH P11 1/290° Elbow.........1 CH P12 1/2" Cross .............1 OH P13 li2°'x1/2°r Ile Tee ....1 OH P14 1-1I4°x1-1I4'1I2"Tee .1 OH P15 1/4'x3° Nipple ........I CH P16 1/2"xl-1/2° Nipple .....6 OH P17 1-1/4' x 2' Nipple .......I OH P18 1-1/4°x3' Nipple . ...... 1 CM El Solenoid Valve Per Data Ordered Shee*TFP2180 .......1 Separately E2 1/2" Tubing Connector - .1 CM E3 1/2" x 24° Tubing ... .... I OH E4 1/2' x 1-1/2° Nipple .....1 CM 30 20 r LOCATION 42 FOR OPTIONAL ELECTRICALLY SUPERVISED 33 N.O. ALARM ., CONTROL VALVE NOTES: Supervised Single Interlock Preaclion Trim with Electric Actuation is comprised of Items 1-44 plus Items P1-Fi8 and Items E1-E4. Use only the Model CV-1 FR Riser Check Valve. All Fittings and Nipples are galvanized (Standard Order). CH: Common Hardware. WI 21 - /124 —e79 37 —33 3° (DN8O) 31 28 GROOVE a GROOVE 21 MODEL DV-5 23 31 DELUGE VALVE SHOWN 33 El (ORDERED E3 . SEPARATELY) E2 E4 39 21 334 21 / ___/ / - NOTES: See Figure 2 of TFP13OS for Deluge Valve Port identification. Route all Tubing to Drip Funnel, Item 14, 41 Pe 10 3 41 93 30 26 7 43 44 38 FIGURE 2A - PART2 0F3 3 INCH (DNBO) MODEL DV-5 DELUGE VALVES SUPERVISED SINGLE INTERLOCK PREACTION WITH ELECTRIC ACTUATION TRIM (52-478-X-116) 0 - EXPLODED VIEW - Page 6 of 14 TFPI 420 NO. DESCRIPTION QTY. P/N 22 1/2' Union ............5 CM 23 11Union ..............1 CM 24 114' 90' Elbow .........1 Cl-I 25 1/2' 90' Elbow .........7 CM 26 1/2'Tee ..............3 CM 27 1/2"x 1/4"x 1/2" Tee ...3 CM 28 3/4 x 1/2' x 3/4" Tee ... 2 CM 29 1's 1/2'90* Elbow .....1 CM 30 1' x 3/4' x 1' Tee .......1 CM 31 2'90°Elbow ..........1 CM 32 1/4's Close Nipple .....2 CM 33 1/21 x Close Nipple .....2 CH 34 1/2' x 1-1/2" Nipple .....10 CM 35 1/2'*2-1/2" Nipple .....2 CM 36 1/2' x 3" Nipple ........1 CM 37 1/2's 5' Nipple ........2 CM 38 1/2's 61 Nipple ........1 CM 39 i/2'x7'Nipple ........2 CM 40 Select Nipple per Table .2 CM 41 Select Nipple per Table - .2 CM 42 Select Nipple per Table - .2 CM 43 314'xl-112"Nipple .....1 CM 44 3/4'x2' Nipple .........I CH 45 Select Nipple per Table - .2 CM 46 1' x Close Nipple 2 CM Pg P8 13 #P17 PLUG UNUSED 30 P8 PORTS ?31 P81 P13 Pi 46 29 36 P16 P16 'r4Y pie N P6 P11 Z P 3 io 67 16 P16 t (GREEN 17 ,) P16 P14 L 43 1 161R?11 Jg)" 28 7 31 49 49 12 39 .0 22 / 34 34 125 4' (DM100) 22 32 27 FLANGE x GROOVE 32 MODEL DV-5 24 DELUGE VALVE SHOWN NO. DESCRIPTION OTY. P/N 1 300 pail 2000 kPa Water Pressure Gauge .2 92-343-1-005 2 1/4' Gauge Test Valve 1 46-005-1-002 3 Model MC-1 Manual Control Station .........1 52-289-2-001 4 Model AD-I Automatic Drain Valve ...........1 52-793-2-004 5 Automatic Shut-Off Valve, Model AS V-i ...........1 92-343-1-021 6 Waterflow Pressure Alarm Switch (PS10-2A) .1 2571 7 1/2' Ball Valve .........2 46-050-1-004 8 1/2' Spring Loaded Check Valve ..........1 92-322-1-002 9 1/2' V-Strainer .........1 52-353-1-005 10 3/4' Swing Check Valve .1 46-049-1-005 11 Not Used .............0 N/A 12 2'Aagle Valve .........1 46-048-1-009 13 Drip Funnel Connector . 1 92-211-1-005 14 Drip Funnel Bracket - .. - 1 92-211-1-003 15 Drip Funnel ...........1 92-343-1-007 16 3/32' Vent Fitting .......1 92-032-1-002 17 114' x 24' Tubing -------1 CM 18 i/2'TubingConneclor ..1 Cl-I 19 112' x 24 Tubing .......1 CM 20 1/4' Plug .... ........... I CH 21 3/4' Plug ......... .....I CH 27 28 21 P17 I P7 35 All a. LOCATION FOR OPTIONAL ELECTRICALLY SUPERVISED 34 N.O, ALARM 25 CONTROL VALVE NOTES: - Supervised Single Interlock Preaction Trim with Electric Actuation is comprised 01 Items 1-49 plus Items P1-P17 and Items E1-E4. Use only the Model CV-1 FR Riser Check Valve. All Fittings and Nipples are galvanized (Standard Order). Cl-I: Common Hardware. NO. DESCRIPTION OTY. P/N 47 ix 3" Nipple ..........1 CH 48 Not Used .............0 N/A 49 2' x 3" Nipple ..........2 CH Pt 250ps1/1750kPa Air Pressure Gauge .....1 92-343-1-012 P2 1/4" Gauge Test Valve ..1 46-005-1.002 P3 Low Air Pressure Alarm Switch (PS IO-2A) ......1 2571 P4 1/4" Pressure Relief Valve ................1 92-343-1.019 P5 1/2" Swing Check Valve .1 46-049-1-004 P6 1/2" Globe Valve .......1 46-047-1.004 P7 2" Angle Valve .........1 46-048-1-009 P8 1/4" Plug .............. 3 CM P9 1/2" x 1/4" Reducing Bushing ..............1 CM P10 1/2" Union ............1 CM P11 1/2" 90' Elbow .........1 CM P12 1/2" Cross ............1 CH P13 1/2"x112"s 1/4"Tee... .1 CH P142'x2"x112"Tee .... ...I CH P15 114"x3' Nipple ........1 CM PIG 1/2" x 1-1/2' Nipple .....6 CH P17 2" x 3" Nipple ..........2 CH El Solenoid Valve Per Data Ordered Sheel1FP2180 ........1 Separately E2 1/21 Tubing Connector .1 CM E3 1/2' x24' Tubing ........1 CM E4 112"xl-1/2 Nipple .....1 CM - Nipple No. - Select Appropriate Nipple Sizes per DV-5 Deluge Valve Size 4' (DM100) 6 (DM150) 8" (DM200) 40 1/2"x2-1/2' 1/2" x5-112' 112'x84/2" NOTES: See Figure 2 of TFP13OS for Deluge Valve Fort identification. Route all Tubing to Drip Funnel, Item 15. 41 1/2's 2" 1/2" x3" 1/2' x3-1/2" 42 1121x6-1!2 1/2' x7.1/2' 112" x9' 45 3/4l.f2' 3/4"x3-112' 3/4' x4-1/2" 4 15 -- El 14 ES - (ORDERED SEPARATELY) RISER E2 CHECK VALVE 38 22 41 22 26 35 25 34 - 34 I FIGURE 2A - PART OF 3 4,6, and 8 INCH (DN100 and DN200) MODEL DV-5 DELUGE VALVES SUPERVISED SINGLE INTERLOCK PREACTION WITH ELECTRIC ACTUATION TRIM (52-478-X--113) C - EXPLODED VIEW— TFPI42O 0 Page 7 of 14 Nipple Number Select Appropriate Nipple Sizes per DV-5 Deluge Valve Size 1.1/2' (DN4O) F 2' (DNSG) 3" (DNSO) 4' (DN100) 6' (DN1SO) 8' (DN200) I 112'xClose 1/2'x2' 112'x 11-1/2" 112'x21/2' 1/2"x5-112' 1/2" x8-1/2" 2 1/2'xClose 1/2'xClose 1/2'x1.1/2' 1/2'x2 1/2'xS' 112"x3.112 3 1/2'x5' 1/2'x5.112' 1/2"x 7* 112'x6.1/2' 1/2" x7-1/2' 1/2" x9" 4 3/4"x1.112' 3/4'xl-1/2' 3/4'x 1-1/2' 314'x2-1/2 3/4'x3-1/2' 314:'x 4-1/2" System Main Drain Size 3/4" NPT 314' NPT 1.1/4" NPT 2' NPT 2' NPT ___________ 2" NPT Main Drain 3/4" NPT 3/4" NPT 1-114 NPT 2' NPT 2' NPT 2" NPT LOW AIR PRESSURE ALARM SWITCH 1/2 INCH NPT CONNECTION FOR SYSTEM k AIR SUPPLY SOLENOID VALVE. ORDERED SEPARATELY 1/2 INCH SYSTEM (NORMALLY CLOSED) CONDUIT AIR SUPPLY CONNECTION PRESSURE FOR 'ELECTRIC GAUGE DETECTION' RISER ) CHECK VALVE NIPPLE (NOTE 1) 2 AUTOMATIC SHUT-OFF VALVE (NORMALLY OPEN) GLQ*U) ALARM TEST VALVE A (NORMALLY CLOSED) 4" (ON-100) ° CHAMBER SUPPLY PRESSURE SYSTEM WATER DIAPHRAGM SUPPLY —4 C MAIN RA DELUGE VALVE FLANGE x GROOVE '. CONTROL VALVE MODEL DV-5 \ (NORMALLY CONNECTION SHOWN CONNECTION FROM 1/2 INCH NPT OPEN) GAUGE - (SIZED PER TABLE) WATER SUPPLY FIGURE 26 1-1/2 fhru 8 INCH (DN40 thru DN200) MODEL DV-5 DELUGE VALVES SUPERVISED SINGLE INTERLOCK PREACTION WITH ELECTRIC ACTUATION TRIM - OPERATIONAL COMPONENTS - WATERFLOW. PRESSURE ALARM SWITCH 3/4 INCH NPT CONNECTION FOR WATER MOTOR —41 ALARM NIPPLE 4 -,-.----- . NIPPLE \ " NOTES: I. Use only the 2" Model CV-1 FR Riser Check Valve with 1-1/2 and 2' DV-5 Valves. Use corresponding sized Model CV-1 FR Riser Check Valves for 3-8' Model DV-5 Valves. Nipples 1-4 vary in length relative to the Model DV-5 size used. Select per the table. All other nipples packed unassembled shall be installed per the appropriate trim exploded view, Figure 2A Part 1 2, or 3. Install subassemblies in alphabetical order. See Figure 2 of TFP1305 for Deluge Valve Port tclentitication. Route all Tubing to Drip Funnel. VENT FITTING SYSTEM (GREEN TINT) AIR SUPPLY / CONTROL VALVE / (NORMALLY /* OPEN)\ SYSTEM MAIN DRAIN CONNECTION SIZED PER TABLE) \ SYSTEM MAIN DRAIN VALVE MAIN \ (NORMALLV DRAIN VALVE \CLOSED) (NORMALLV\ E DRIP r AUTOMATIC FUNNEL DRAIN WITH 1-1/4 B VALVE INCH NPT \ CONNECTION TO DRAIN PLUG F UNUSED 3 DIAPHRAGM CHAMBER PRESSURE GAUGE MANUAL CONTROL STATION Page 8of 14 TFPI420 * MINIMUM CLEARANCE. * A B - * C * 0 £ QI II 1/2"NPS M DIAPHRAGM o 0 CHAMBER SUPPLY C 13 CONNECTING TRIM LN (FIELD FABRICATED) L - F J r:: \ ___ MAIN 2 NTROL COVALVE DRAIN DRAIN :1: LEFT VIEW FRONT VIEW FIGURE 3 1-1/2 thru 8 INCH (DN4O and DN200) MODEL DV-5 DELUGE VALVES SUPERVISED SINGLE INTERLOCK PREACTION WITH ELECTRIC ACTUATION TRIM - NOMINAL INSTALLATION DIMENSIONS - Valve Nominal Dimensions _Installation in Inches and (mm) Size A B C D F F G H J K M 1-1/2 7.00 8.88 13.00 10.50 20.50 4.00 5.81 5.81 3.00 7.00 14.81 (DN40) (177,8) (225,4) (330,2) (266,7) (520,7) (101,6) (147,6) (147,6) (76,2) (177,8) r0022055)) (376,2) 7.13 9.13 13.00 10.50 21.06 3.13 6.00 6.00 3.00 7.00 15.38 (DN5O) (181,0) (231,8) (330,2) (266,7) (535,0) (79,4) (152,4) (152,4) (76,2) (177,8) (390,5) 7.81 10.44 14.50 10.50 25.00 1.69 6.69 6.69 4.25 7.00 21.13 (DN80) (198,4) (265,1) (368,3) (266,7) (635,0) (42,9) (170,0) (170,0) (108,0) (177,8) (6,4) (536,6) 10.00 11.75 17.88 10.50 29.13 1.75 6.50 8.56 6.25 7.13 0.38 25.38 (DN100) (254,0) (298,5) (454,0) (266,7) (739,8) (44,5) (165ifl (217,5) (158,8) (181,0) (9,5) (45) 6" 11.38 14.31 18.75 10.50 31.94 3.50 7.88 9.94 6.25 7.13 1.56 29.63 (DN150) (289,0) (363,5) (476,3) (266,7) (811,2) (88,9) (200,0) (252,4) (158,8) (181,0) (39,7) (752,5) 8" 12.00 16.00 21.25 10.50 36.75 1.75 10.75 10.63 6.25 7.13 7.13 36.50 (DN200) (304,8) (406,4) (539,8) (266,7) (933,5) (44,5) (273,1) (269,9) (158,8) (181,0) (181,0) (927,1) TFPI 420 Page 9 of 14 Chamber is pressurized through the trim connections from the inlet side of the system's main control valve, such as an O.S.&Y. gate valve or butterfly valve (Fig. 1). Operation of an electrical detection de- vice such as a heat sensitive thermo- stat, smoke detector, or electrical man- ual control station signals the deluge valve releasing panel to energize the Solenoid Valve. In turn, the energized Solenoid Valve opens to release water from the Diaphragm Chamber faster than it can be replenished through the 1/8 inch (3,2 mm) restriction provided by the Model ASV-1 Automatic Shut- Off Valve in the diaphragm supply con- nection (Item 5 - Fig. 2A, also de- scribed in Technical Data Sheet TFP1 384). This results in a rapid pres- sure drop in the Diaphragm Chamber to below the valve trip point. The water supply pressure then forces the Dia- phragm open, permitting water to flow into the system piping, as well as through the Alarm Port to actuate the system alarms. As water flows into the system, the pilot chamber of the Model ASV-1 Automatic Shut-Off Valve (Item 5 - Fig. 2A) becomes pressurized and the ASV-1 automatically shuts off the dia- phragm chamber supply flow to the DV-5 Diaphragm Chamber. Shutting off the diaphragm chamber supply flow prevents the DV-5 Diaphragm Cham- ber from becoming re-pressurized, thereby preventing inadvertent closing of the DV-5 during a fire (as may be the case should the Solenoid Valve be- come de-energized after its initial op- eration). WARNING The Model DV-5 Supervised Single In- terlock Preaction System with Electric Actuation Trim described herein must be installed and maintained in compli- ance with this document, as well as with the applicable standards of the National Fire Protection Association, in addition to the standards of any other authorities having jurisdiction. Failure to do so may impair the per- formance of the related devices. The owner is responsible for maintain- ing their fire protection system and de- vices in proper operating condition. The installing contractor or manufac- turer should be contacted with any questions. Technical Data Approvals UL and C-UL Listed. FM Approved. Deluge Valve Model DV-5. Riser Check Valve Model CV-1 FR. NOTE 1-1/2 inch (DN40) risers utilize a 2 inch (DN50) Riser Check valve in combina- tion with the 1-1/2 inch (DN40) Model DV-5 Deluge Valve. Valve Trim The Supervised Single Interlock Pre- action System With Electric Actuation Trim (Fig. 2A/2B) forms a part of the laboratory listings and approvals. The trim is necessary for proper operation of the DV-5 Valve. Each package of trim includes the fol- lowing items: Water Supply Pressure Gauge Diaphragm Chamber Pressure Gauge Diaphragm Chamber Connections Manual Control Station Main Drain Valve System Drain Valve Alarm Test Valve Automatic Drain Valve System Air Pressure Gauge Air Supply Connections Low Air Pressure Supervisory Switch Waterflow Pressure Alarm Switch To ease field assembly of the trim ar- rangement, the trim components are provided partially assembled as shown in Figure 2B. The trim arrangement is provided with galvanized or black nipples and fit- tings. The galvanized trim is intended for non-corrosive or corrosive condi- tions, whereas the black trim is princi- pally intended for use with AFFF sys- tems. NOTE When the system pressure is greater than 175 psi (12,1 bar), provision is to be made to replace the standard order 300 psi (20,7 bar) Water Pressure Gauges, shown in Figure 2A/2B with separately ordered 600 psi (41,4 bar) Water Pressure Gauges. Detection System In order for a single interlock preaction system to be hydraulically calculated as a wet pipe system, as opposed to a dry pipe sprinkler system, the detec- tion system must be designed to oper- ate sooner than the automatic sprin- klers on the sprinkler piping. The Supervised Single Interlock Pre- action System With Electric Actuation Trim provides for electric operation of the DV-5 Valve by a detection system consisting of electrical devices such as heat sensitive thermostats, smoke de- tectors, and/or electric manual pull sta- tions. Information on the various types of separately ordered Solenoid Valves that may be used with this trim pack- age is given in Technical Data Sheet TFP2180. Nominal installation dimen- sions for the Supervised Single Inter- lock Preaction System With Electric Actuation Trim are shown in Figure 3. NOTES Approval by Factory Mutual is contin- gent on the use of an FM Approved 24 VDC Solenoid Valve (P/N 52-287-1- 024 or P/N 52-287-1-124). FM only approves solenoid valves for use in non-hazardous locations. Consult with the Authority Having Ju- risdiction regarding installation criteria pertaining to electric actuation cir- cuitry. The Supervised Single Interlock Pre- action System With Electric Actuation Trim is provided with a Model ASV-1 Automatic Shut-Off Valve (Item 5 - Fig. 2A); consequently, the release circuit of the releasing panel need only pro- vide the standard ten minutes of alarm condition intended to energize the So- lenoid Valve. After the ten minute du- ration, should the Solenoid Valve be- come de-energized and close (especially while operating under bat- tery back-up), the Automatic Shut-Off Valve will have already automatically closed thereby preventing the DV-5 Diaphragm Chamber from becoming re-pressurized and preventing an in- advertent closing of the DV-5 during a fire event. System Air Pressure Requirements The supervisory air (nitrogen) pres- sure is to be 10 plus or minus 2 psi (0,69 plus or minus 0,07 bar). The use of a higher supervisory pressure is subject to approval by the Authority Having Jurisdiction, and it should be understood that the use of a higher supervisory pressure may increase water delivery time. The use of a lower supervisory pressure may prevent clearing the alarm of the Supervisory Low Pressure Alarm Switch (Item P3 - Fig. 2A), which is factory set to alarm at 5 plus or minus 1 psi (0,34 plus or minus 0,07 bar) on decreasing pres- VA WINFAME ••U•I 1511111111 WA mono on FAMEMENESEN •'iu imolAmosull 11111 111111'a on BONN FAMONEMENIN mrson vuuIuIuuIuuuuuuIuII FAN uu moor llI•IuII•!AU•u 01FAMEN milli 11111 1111f ME 11111FA 011111011111111 VISION raiuu1111111111 1111A 011119 Al UUUUUIIII FANNIN TFPI 420 Page 11 of 14 must be maintained at minimum tern- having jurisdiction and/or the National perature of 40°F/4°C. Electric Code. S sure. The supervisory air supply pres- sure of 10 plus or minus 2 psi (0,69 plus or minus 0,07 bar) can be pro- vided by any of the following methods. Refer to the applicable data sheet for laboratory approval information. Model G16AC812 (self contained) Automatic Supervisory Air Supply described in Gem Technical Data Sheet TD 126. A maximum 200 psi (13,8 bar) plant air supply in combination with the Model AMD-1 Air Maintenance De- vice described in Technical Data Sheet TFP122I. A maximum 3000 psi (206,9 bar) nitrogen cylinder in combination with the Model AMD-3 Nitrogen Mainte- nance Device described in Techni- cal Data Sheet TFP1 241. NOTE The dew point of the air or nitrogen supply, for a system exposed to freez- ing conditions, must be maintained be- low the lowest ambient temperature to which the system piping will be ex- posed. Introduction of moisture into the system piping can create ice build up which could prevent proper opera- tion of the system. The Supervisory Low Pressure Alarm Switch (Item P3 - Fig. 2A) is factory set at 5 plus or minus 1 psi (0,34 plus or minus 0,07 bar) on decreasing pres- sure. The Pressure Relief Valve (Item P4- Fig. 2A) is factory set to fully open at 25 plus or minus 2 psi (1,72 plus or minus 0,14 bar) and it begins to crack open at a pressure of about 18 psi (1,24 bar). Friction Loss The nominal pressure loss versus flow data for the Model DV-5 Deluge Valve plus Riser Check Valve is provided in Graph A. Installation NOTES 1-1/2 inch (DN40) risers utilize a 2 inch (DN50) Riser Check valve in combina- tion with the 1-1/2 inch (DN40) Model DV-5 Deluge Valve. Proper operation of the Model DV-5 Deluge Valves depends upon their trim being installed in accordance with the instructions given in this Technical Data Sheet. Failure to follow the ap- propriate trim diagram may prevent the DV-5 Valve from functioning prop- erly, as well as void listings, approvals, and the manufacturer's warranties. The DV-5 Valve must be installed in a readily visible and accessible location. The DV-5 Valve and associated trim Heat tracing of the DV-5 Valve or its associated trim is not permitted. Heat tracing can result in the formation of hardened mineral deposits that are ca- pable of preventing proper operation. The Model DV-5 Deluge Valve is to be installed in accordance with the follow- ing criteria: Step 1. All nipples, fittings, and de- vices must be clean and free of scale and burrs before installation. Use pipe thread sealant sparingly on male pipe threads only. Step 2. The DV-5 Valve must be trimmed in accordance with Figure 2A/2B. Step 3. Care must be taken to ensure that check valves, strainers, globe valves, etc. are installed with the flow arrows in the proper direction. Step 4. Drain tubing to the drip funnel must be installed with smooth bends that will not restrict flow. Step 5. The main drain and drip funnel drain may be interconnected provided a check valve is located at least 12 inches (300 mm) below the drip funnel. Step 6, Suitable provision must be made for disposal of drain water. Drainage water must be directed such that it will not cause accidental dam- age to property or danger to persons. Step 7, Connect the Diaphragm Chamber Supply Control Valve to the inlet side of the system's main control valve in order to facilitate setting of the DV-5 Valve (Fig. 3). Step 8. Unused pressure alarm switch connections must be plugged. Step 9. A suitable automatic supervi- sory air (nitrogen) supply, as described in the Technical Data Section, is to be installed in accordance with the appli- cable Technical Data Sheet and set for 10 plus or minus 2 psi (0,69 plus or minus 0,14 bar). Step 10. A desiccant dryer, when re- quired for the supervisory air supply, is to be installed between a drip leg and the Model AMD-1 Air Maintenance De- vice or between the Model G16AC812 Automatic Supervisory Air Supply and the Preaction Trim. Step 11. The Supervisory Low Pres- sure Alarm Switch is to be wired to the supervisory alarm initiating circuit of an alarm panel. Step 12. Conduit and electrical con- nections are to be made in accordance with the requirements of the authority Step 13. Before a system hydrostatic test is performed in accordance with NFPA 13 system acceptance test re- quirements, the DV-5 Diaphragm Chamber is to be depressurized; the Automatic Drain Valve (Item 4, Fig. 2A) is to be temporarily replaced with a 1/2 inch NPT plug, the 3/32 inch Vent Fit- ting (16 - Fig. 2A) is to be temporarily replaced with a 1/4 inch NPT plug, and the Diaphragm Cover Bolts must be uniformly and securely tightened using a cross-draw sequence. After tightening, double-check to make cer- tain that all of the Diaphragm Cover Bolts are securely tightened. Valve Setting Procedure Steps 1 through 12 are to be per- formed when initially setting the Model DV-5 Deluge Valve; after an opera- tional test of the fire protection system; or, after system operation due to a fire. Step 1. Close the Main Control Valve, Step 2. Close the Diaphragm Cham- ber Supply Control Valve and the Su- pervisory Air Supply Control Valve. Step 3. Open the Main Drain Valve, System Drain Valve, and all auxiliary drains in the system. After water ceases to discharge, close the System Drain Valve and auxiliary drain valves. Leave the Main Drain Valve open. Step 4. Depress the plunger of the Automatic Drain Valve to verify that it is open and that the DV-5 Valve is completely drained. Step 5. Clean the Strainer in the Dia- phragm Chamber Supply connection by removing the clean-out plug and strainer basket. The Strainer may be flushed out by momentarily opening the Diaphragm Chamber Supply Con- trol Valve. Step 6. Reset the actuation system. Manual Actuation - Push the operat- ing lever up; however, do not close the hinged cover at this time. Electric Actuation - Reset the electric detection system in accordance with the manufacturer's instructions to de- energize the Solenoid Valve. Step 7. Open the Diaphragm Chamber Supply Control Valve and allow time for full pressure to build up in the Dia- phragm Chamber. Step 8. Operate (open) the Manual Control Station to vent trapped air from the Diaphragm Chamber, If necessary, Page 12 of 14 TFPI 420 S first open the hinged cover, and then fully pull down on the operating lever. SLOWLY close the operating lever, by pushing it up, after aerated water ceases to discharge from the Manual Control Station drain tubing. Close the hinged cover and insert a new break rod in the small hole through the top of the enclosing box. Step 9. Inspect the drain connections from the Manual Control Station and the Solenoid Valve. Any leaks must be corrected before proceeding to the next step. Step 10. Verify the ability for the DV-5 Diaphragm to hold pressure as fol- lows: With the diaphragm chamber pressur- ized per Step 8, temporarily close the Diaphragm Chamber Supply Control Valve, and monitor the Diaphragm Chamber Pressure Gauge for a drop in pressure. If a drop in pressure is noted, the DV-5 Diaphragm is to be replaced and/or any leaks must be corrected before proceeding to the next step. If the Diaphragm Chamber Pressure Gauge does not indicate a drop in pressure, re-open the Diaphragm Chamber Supply Control Valve and proceed to the next step. Step 11. Replace operated automatic sprinklers on the system piping and then open the Supervisory Air Supply Control Valve and allow the system to automatically re-establish its nominal air pressure of 10 psi (0,69 bar). Ob- serve the Automatic Drain Valve for leaks. If there are leaks, deter- mine/correct the cause of the leakage problem within the Riser Check Valve. NOTE In order to prevent the possibility of a subsequent operation of an over- heated solder type automatic sprin- kler, any solder type automatic sprin- klers that were possibly exposed to a temperature greater than their maxi- mum rated ambient must be replaced. Step 12. Slowly open the Main Control Valve. Close the Main Drain Valve as soon as water discharges from the drain connection. Observe the Auto- matic Drain Valve for leaks. If there are leaks, determine/correct the cause of the leakage problem. If there are no leaks, the DV-5 Valve is ready to be placed in service and the Main Control Valve must then be fully opened. the pressure is greater than 250 psi (17,2 bar), the pressure is to be re- lieved by partially and temporarily opening the Manual Control Station; however, do not allow the pressure as indicated on the Diaphragm Chamber Pressure Gauge to drop below the supply pressure shown on the Water Supply Pressure Gauge, since this ac- tion may result in tripping of the DV-5 Valve. After setting a fire protection system, notify the proper authorities and ad- vise those responsible for monitoring proprietary and/or central station alarms. Care and Maintenance The following procedures, inspections, and maintenance must be performed as indicated, in addition to any specific requirements of the NFPA, and any impairment must be immediately cor- rected. The owner is responsible for the in- spection, testing, and maintenance of their fire protection system and de- vices in compliance with this docu- ment, as well as with the applicable standards of the National Fire Protec- tion Association (e.g., NFPA 25), in addition to the standards of any authority having jurisdiction. The in- stalling contractor or product manufac- turer should be contacted relative to any questions. It is recommended that automatic sprinkler systems be inspected, tested, and maintained by a qualified Inspection Service in accordance with local requirements and/or national codes. NOTES Some of the procedures outlined in this section will result in operation of the associated alarms. Consequently, notification must first be given to the owner and the fire department, central station, or other signal station to which the alarms are connected. Before closing a fire protection system main control valve for maintenance work on the fire protection system that it controls, permission to shutdown the affected fire protection systems must first be obtained from the proper authorities and all personnel who may be affected by this action must be no- tified. ing a fire condition) must be verified at least once a year as follows: Step 1. It water must be prevented from flowing beyond the riser, perform the following steps. Close the Main Control Valve. Open the Main Drain Valve. Open the Main Control Valve one turn beyond the position at which water just begins to flow from the Main Drain Valve. Close the Main Drain Valve. Step 2. Test the deluge releasing panel in accordance with the manufac- turer's instructions to energize the So- lenoid Valve. NOTE Be prepared to quickly perform Steps 3, 4, and 5, if water must be prevented from flowing beyond the riser. Step 3. Verify that the DV-5 Valve has tripped, as indicated by the flow of water into the system. Step 4. Close the system's Main Con- trol Valve. Step 5. Close the Diaphragm Cham- ber Supply Control Valve and the Su- pervisory Air Supply Control Valve. Step 6. Reset the DV-5 Deluge Valve in accordance with the Valve Setting Procedure. Quarterly Waterfiow Alarm Test Procedure Testing of the system waterfiow alarms must be performed quarterly. To test the waterflow alarm, open the Alarm Test Valve, which will allow a flow of water to the Waterf low Pressure Alarm Switch and/or Water Motor Alarm. Upon satisfactory completion of the test, close the Alarm Test Valve, Quarterly Solenoid Valve Test Procedure For Electric Actuation Proper operation of the Solenoid Valve for electric actuation must be verified at least quarterly as follows: Step 1. Close the Main Control Valve. Step 2. Open the Main Drain Valve. Step 3. Test the deluge releasing panel in accordance with the manufac- turer's instructions to energize the so- lenoid valve. Step 4. Verify that the flow of water from the Solenoid Valve drain connec- tion increases to a full flow. Step 5. Verify that the Diaphragm Chamber pressure has decreased to below 25% of the water supply pres- sure. Step 6. Reset the electric detection NOTES . When the Main Control Valve is Annual Operation Test Procedure opened, the pressure on the Dia- Proper operation of the DV-5 Valve phragm Chamber may increase. This (i.e., opening of the DV-5 Valve as dur- increase in pressure is normal, and if TFPI42O Page 13 of 14 S system in accordance with the manu- facturer's instructions to de-energize the solenoid valve. Check the Solenoid Valve drain for leaks. Any leaks must be corrected before proceeding to the next step. Step 7. Slowly open the Main Control Valve. Close the Main Drain Valve as soon as water discharges from the drain connection. Observe the Auto- matic Drain Valve for leaks. If there are leaks, determine/correct the cause of the leakage problem. If there are no leaks, the DV-5 Valve is ready to be placed in service and the Main Control Valve must then be fully opened. NOTE When the Main Control Valve is opened, the pressure on the Dia- phragm Chamber may increase. This increase in pressure is normal, and if the pressure is greater than 250 psi (17,2 bar), the pressure is to be re- lieved by partially and temporarily opening the Manual Control Station; however, do not allow the pressure as indicated on the Diaphragm Chamber Pressure Gauge to drop below the supply pressure shown on the Water Supply Pressure Gauge, since this ac- tion may result in tripping of the DV-5 Valve. Quarterly Supervisory Low Pres- sure Alarm Test Procedure Proper operation of the Supervisory Low Pressure Alarm Switch must be performed quarterly as follows: Step 1. Crack open the System Main Drain Valve for the Riser Check Valve (Item P7, Figure 2A) to slowly relieve supervisory air pressure from the sys- tem. Verify that the Supervisory Low Pressure Alarm Switch is operational and that the low pressure set point is approximately 5 psi (0,34 bar). Step 2. Close the System Main Drain Valve (Item P7, Figure 2A) and allow the system supervisory pressure of 10 plus or minus 2 psi (0,69 plus or minus 0,14 bar) to be automatically re-estab- lished. The Supervisory Low Pressure Alarm Switch should return to its "nor- mal" condition. Pressure Relief Valve Maintenance Over pressurization of the system pip- ing with air will result in the opening of the Pressure Relief Valve (Item P4, Fig. 2A). If the Relief Valve continues to bleed air after the system pressure has been reduced to its normal super- visory pressure range of 10 plus or minus 2 psi (0,69 plus or minus 0,14 bar), most likely debris became lodged in the seating area. To help clean the seating area, slowly pull up on the ring at the top of the Relief Valve to allow a full flow of air through the Relief Valve, and then release the ring to allow the Relief Valve to snap closed. Repeat the cleaning procedure as necessary Limited Warranty Products manufactured by Tyco Fire Products are warranted solely to the original Buyer for ten (10) years against defects in material and work- manship when paid for and properly installed and maintained under normal use and service. This warranty will ex- pire ten (10) years from date of ship- ment by Tyco Fire Products. No war- ranty is given for products or components manufactured by compa- nies not affiliated by ownership with Tyco Fire Products or for products and components which have been subject to misuse, improper installation, corro- sion, or which have not been installed, maintained, modified or repaired in ac- cordance with applicable Standards of the National Fire Protection Associa- tion, and/or the standards of any other Authorities Having Jurisdiction. Mate- rials found by Tyco Fire Products to be defective shall be either repaired or replaced, at Tyco Fire Products' sole option. Tyco Fire Products neither as- sumes, nor authorizes any person to assume for it, any other obligation in connection with the sale of products or parts of products. Tyco Fire Products shall not be responsible for sprinkler system design errors or inaccurate or incomplete information supplied by Buyer or Buyer's representatives. IN NO EVENT SHALL TYCO FIRE PRODUCTS BE LIABLE, IN CON- TRACT, TORT, STRICT LIABILITY OR UNDER ANY OTHER LEGAL THE- ORY, FOR INCIDENTAL, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LABOR CHARGES, RE- GARDLESS OF WHETHER TYCO FIRE PRODUCTS WAS INFORMED ABOUT THE POSSIBILITY OF SUCH DAMAGES, AND IN NO EVENT SHALL TYCO FIRE PRODUCTS' LI- ABILITY EXCEED AN AMOUNT EQUAL TO THE SALES PRICE. THE FOREGOING WARRANTY IS MADE IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESS OR Ordering Procedure With reference to Table A on Page 14, the following items must be ordered separately: Deluge Valve Riser Check Valve Coupling (Deluge Valve to Riser Check Valve) Single Interlock Preaction Trim Supervisory Air Supply Solenoid Valve Accessories NOTE 1-1/2 inch (DN40) risers utilize a 2 inch (DN50) Riser Check valve in combina- tion with the 1-1/2 inch (DN40) Model DV-5 Deluge Valve. Part Numbers for factory pre-trimmed Model DV-5 Valves are provided in the Price Book. Replacement Trim Parts: Specify: (description) for use with Model DV-5 Deluge Valve, P/N (see Figure 2A). TFPI 420 S Page 14 of 14 DELUGE VALVE (SELECT ONE) P/N's are for American Standard Groove x Groove Connections, and Threaded Ports, For other configurations refer to Technical Data Sheet 1FP1305. Specify: (size) Model DV-5 groove x groove Deluge Valve, P/N (specify). 1-1/2 Inch ..........................................................P/N 52-477-1-919 2 Inch .............................................................P/N 52-477-1-910 3 Inch .............................................................P/N 52-477-1-912 4 Inch .............................................................P/N 52-477-1-913 6 Inch .............................................................P/N 52-477-1-915 8 Inch .............................................................P/N 52-477-1-916 RISER CHECK VALVE (SELECT ONE) P/N's are for American Standard Grooved Connections. For other configurations refer to Technical Data Sheet TFP950 for the groove x groove Model CV-1 FR Riser Check Valve. Specify: (size), Model CV-1 FR groove xgroove Riser Check Valve, P/N (specify). For 1-1/2 inch risers, use the 2 Inch Riser Check Valve. 2 Inch .............................................................P/N 59-590-1-020 3 Inch .............................................................P/N 59-590-1-030 4 Inch .............................................................P/N 59-590.1-040 6 Inch .............................................................P/N 59-590-1-060 8 Inch .............................................................P/N 59-590-1-080 COUPLING (SELECT ONE) P/N's are for American Standard Grooved Connections. For other configurations and finishes refer to Technical Data Sheet TFP1830 or TFP1880. A coupling to attach the Riser Check Valve to the outlet of the Deluge Valve must be separately ordered. Specify: (Size), (Figure #), painted, (description), P/N (specify). For 1-1/2 inch risers, order an additional Reducing Coupling for the outlet of the 2 inch Riser Check Valve. 2 x 1-1/2 Inch Figure 716 Painted Reducing Coupling ....................... PIN 7162015ES 2 Inch Figure 772 Painted Rigid Coupling ................................P/N 77220ASC 3 Inch Figure 772 Painted Rigid Coupling ................................P/N 77230ASC 4 Inch Figure 772 Painted Rigid Coupling ................................P/N 77240ASC 6 Inch Figure 772 Painted Rigid Coupling ................................P/N 77260ASC 8 Inch Figure 772 Painted Rigid Coupling ................................P/N 77280ASC PREACTION TRIM (SELECT ONE) Specify: (specify size and finish - galvanized is standard) Semi-Preassembled Super- vised Single Interlock Preaction System With Electric Actuation Trim for Model DV-5 Deluge Valves, P/N (specify). 1-1/2 & 2 Inch Galvanized .............................................P/N 52-478-2-119 1-1/2 & 2 Inch Black .................................................. PIN 52-478-1-119 3 Inch Galvanized ................ .................................... PIN 52-478-2-116 3 Inch Black ........................................................P/N 52-478-1-116 4, 6 & 8 Inch Galvanized ..............................................P/N 52-478-2-113 4,6 & 8 Inch Black ...................................................P/N 52-478-1-113 SUPERVISORY AIR SUPPLY (SELECT ONE) A device capable of maintaining a nominal system air or nitrogen pressure of nominal 10 psi (0,69 bar) must be separately ordered. Specify: (Specify model and description), P/N (specify). Model AMD-1 Air Maintenance Device (TFP1221) .........................P/N 52-324-2-002 Model AMD-3 Nitrogen Maintenance Device (TFP1241) ....................P/N 52-328-2-001 Model G16AC812 Automatic Supervisory Air Supply (TD126) ................P/N 52-150-1-001 SOLENOID VALVE (SELECT ONE) A Solenoid Valve compatible with the anticipated maximum water supply pressure must be ordered separately. Refer to Technical Data Sheet 1FP2180 for other voltage ratings and NEMA classifications. Specify: 24 VDC, NEMA 2, 4, and 4X, (specify 175 or 250 psi) Solenoid Valve, P/N (specify). 175 psi ............................................................P/N 52-287-1-024 250 psi ............................................................P/N 52-287-1-124 ACCESSORIES (AS NEEDED) Specify: (description), PN (specify). 600 PSI Water Pressure Gauge ........................................P/N 92-343-1-004 Model WMA-1 Water Motor Alarm (TFP921) ..............................P/N 52-630-1-001 TABLE A - ORDERING LIST TYCO FIRE PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446 EA S 1i Re abk Bulletin 251 Rev. R Mode's A-2 & B-i Automatic Pressure Maintenance Devices Instructions for Installation, Operation, Care and Maintenance The Reliable Automatic Sprinkler Co., Inc., 103 Fairview Park Drive, Elmsford, New York 10523 Operation Model A-2 Pressure Maintenance Device W (Refer to Figure 1) he Model A-2 Pressure Maintenance Device (PMD) is de- signed for use where a source of compressed air (plant air system, tank-mounted compressor with a pressure control, etc.) or nitrogen cylinder (equipped with a regulating de- vice) is available (refer to the section in this technical bulle- tin titled Installation"). The regulator in the Model A-2 PMD reduces higher pressure air or nitrogen to a level required by a dry pipe valve, dry pilot line, or a deluge valve based preaction system. The Model A-2 PMD will maintain a con- stant pressure in the system regardless of any pressure fluctuations from the compressed air or nitrogen source. Basic functionality of components (refer to Figure 1): The strainer's (Item 2) function is to prevent any foreign matter that may be present in the air supply, from traveling to the regulator (Item 1) and the check valve (Item 3), thereby en- suring their normal operation. The check valve's function is to prevent the reverse flow of water resulting from a dry pipe or deluge valve's operation, from reaching the regulator. The globe valves (Item 4) allow for the servicing (if needed) of the strainer (Item 2) and regulator (Item 1) without having to shut down the sprinkler system. The ball valve (Item 5) permits the rapid restoration (quick-fill) of the required sys- tem air pressure after service or operation. The ball valve (Item 5) must be closed and the globe valves (Item 4) must be open for proper automatic operation. Models B-i Pressure Maintenance Device (Refer to Figure 2) The Model B-i Pressure Maintenance Device (PMD) is designed for use in conjunction with the Reliable Model A Tankless Air Compressor in order to maintain the correct air pressure in a dry pipe valve or dry pilot line (refer to the section in this technical bulletin titled "Installation"). The Re- liable Model A Tankless Air Compressor is controlled on or off by the air pressure level present in the dry pipe valve or dry pilot line via wiring between the compressor's motor and the contacts of the Model B-i PMD's pressure switch. Basic functionality of components (referto Figure 2): A drop in the sprinkler system's air pressure causes the contacts of the pressure switch (Item i) to close, thereby activating the air compressor . When the pre-adjusted level of air pressure is restored, the pressure switch's contacts re-open, thereby deactivating the air compressor. The pressure switch (Item 1) is also equipped with an unloader valve that automati- cally bleeds off the air compressor's outlet pressure each time the contacts of the pressure switch open. This protects the air compressor's motor from overloading during start- up. Like the Model A-2 PMD, the Model B-i has a strainer (Item 2) for contamination control and a check valve (Item 3) to prevent reverse water flow. The ball valve (Item 5) and globe valves (Item 4) are also identical in configuration and function as with the Model A-2 PMD. Likewise, the ball valve .(Item 5) must be closed and the globe valves (Item 4) must be open for proper automatic operation Adjustment Model A-2 Pressure Maintenance Device (Refer to Figure 1) The pressure regulator (Item i) is factory set to maintain a nominal system air or nitrogen pressure of 30 psi (2,1 bar). In order to change the outlet pressure, loosen the locknut at the top of regulator and turn the adjustment screw clockwise to increase pressure. To decrease the pressure, turn the adjusting screw counter clockwise. The resulting pressure can be determined at the sprinkler system air gauge once the air flow through the device has ceased, or at the optional gauge location. Shown on Figure 1. Note: The locknut of the regulator (Item i) must be tight- ened after adjusting in order to prevent an accidental change in the pressure setting. Adjustable Outlet Pressure Range: 5 psi - to - 50 psi (0,3 bar - to - 3,4 bar) Maximum Inlet Pressure: 175 psi (12 bar) Model B-i Pressure Maintenance Device The pressure switch (Item i) is factory set to maintain a nominal system air pressure of 35 psi (2,4 bar). In order to change the setting, remove the pressure switch's cov- er and follow the directions contained within the switch. Electrical Rating: Single Phase: 120 Volts AC; 2 hp 240 Volts AC; 3 h 600 Volts AC; 5 hp Three Phase: 240 Volts AC; 5 hp 600 Volts AC; 5 h 115-230 Volts DC; 3 hp Adiustable Outlet Pressure Range: 14 psi - to -60 psi (1,0 bar- to - 4,1 bar) Maximum Inlet Pressure: 175 psi (12 bar) 2. C Model A-2 Pressure Maintenance Device P/N 6304000135, (All steel pipe fittings are galvanized) Item Part No. No.Req'd Description 1 98681630 Regulator, 5-50 psi 1 2 98727606 Strainer, 1/4" NPT, 90 1 3 96816902 Check Valve, ¼" 1 4 98840172 Globe Valve l/4" 1 5 98840108 Butterfly Valve, 3%" 1 6 98815201 Union, 1/4" 1 7 96606616 Tee, 3%"x3%"x1/4" 2 8 98543234 Nipple, 3/4" x 31/2" 2 9 98543226 Nipple, 1/4" x 11/2" 4 10 98174404 Elbow, 1%" 1 11 98543268 Nipple, 1%" xl" 3 12 96606608 Tee, 1/4" 1 13 98614403 1 Plug, 1/4" 1 11 10 2116 11 9 Optional 4 Pneumatic 1,3 Location Pressure Guage 1,3 From Air 9 12 or Nitrogen Supply 9 / To 7 System 251FCOJA Figure 1 S Model B-i Pressure Maintenance Device P/N 6304010100, (All steel pipe fittings are galvanized) Item Part No. No.Req'd Description 1 98728801 Pressure Switch, /e" NPT 1 2 98727607 Strainer, 1/4", 30 Mesh 1 3 96816902 Check Valve, 1/4" 1 4 98840172 Globe Valve, ¼" 1 5 98840108 Butterfly Valve, 3%" 1 6 98815201 Union, 1/4" 1 7 96606616 Tee, 3%"x 3%" x¼" 2 8 98543233 Nipple, 3%" x 2½" 2 9 98543226 Nipple, 1%" x 11/2" 4 10 96606608 Tee, 1/4" 1 11 98750004 Cross, ¼" 1 12 98543227 Nipple, ¼" x Close 1 13 98523100 Restrictor Nipple, ¼" 1 14 98768000 Copper Tubing, ¼" O.D. 1 15 98085630 Comp. Fitting, ¼" x ¼" 1 16 98048034 Reducer Bushing 3/8" x ¼" 1 17 98614403 Plug, ¼" 1 Figure 2 3. 14 15 10 2 1 13 I 9 4 16 Optional - 12 Pneumatic 6 Pressure Gauge From 4 17 11 Location Tonk/ess Compressor 7 9 S S To 251FG02C System Model A-2 Pressure Maintenance Device Make sure the air flow through the Pressure Maintenance Device is as shown by the arrows in Figures 1,4,6,8, 9and 11-13. Install the Pressure Maintenance Device as close to the dry pipe valve air line trimmings as pos- sible. Install the Pressure Maintenance Device in the air supply immediately leading to the del- uge or preaction trim. Refer to separate dry pipe valve, deluge valve or preaction system bulletins for the additional installation information. Model B-i Pressure Maintenance Device Make sure the air flow through the Device is as shown by the arrows in Figures 2, 5-7 and 10. Remove the pressure switch's (Item 1) cover and connect the wiring in accordance with the Nation- al Electric Code or other appropriate standards. The connections should be as shown in Figure 3 for single phase wiring of thermally protected compressor motors. Refer to separate dry pipe valve and deluge valve bulletins for additional in- stallation information. Air Compressor (REF. WIRING DIAGRAM ATTACHED TO AIR COMPRESSOR) 25 1FGO4E Figure 3 Inspection and Maintenance Refer to Figures i &2. Review the latest NFPA 13 and NFPA 25 Standards, . any appropriate dry pipe or deluge valve installation bulletins, and the section in this bulletin titled "Instal- lation" to ensure that the pressure maintenance de- vice is installed properly. Make sure that both '/4" globe valves (Item 4) are open and that the 3,4" ball valve (Item 5) is closed. Check the gas pressure in the dry pipe, deluge or preaction system at the pressure gauge located on those devices. See the section titled "Adjustment" if any are required. If maintenance is to be performed on Items 1, 2 or 3 of the pressure maintenance device, make sure that both globe valves (Item 4) are closed and that pressure has been relieved from the section through the 1/4" union (Item 6). These valves must be opened again in order to restore proper automatic operation. The strainer (Item 2) should be cleaned periodically to prevent contamination from blocking air flow. This can be done by removing the strainer's cap and wip- ing or blowing off any collected debris. Make sure the check valve (Item 3) is installed ac- cording to the schematic with the arrow on its hex- agonal side pointing in the required direction of air flow. If the regulator (Item 1) in the Model A-2 Pressure Maintenance Device is constantly leaking at the ad- justing screw, the regulator may contain dirt keep- ing the poppet open and should be cleaned or re- placed. Check the inside housing of pressure switch (Item 1) of the Model B-i Pressure Maintenance Device for dirt or foreign matter and verify that the wiring is fastened securely and is wiring insulation is in good condition, WARNING: Do not contact the electrical wiring when the power is on Installation As shown in Figures 4 through 13, Pressure Maintenance Devices are installed in the air supply line leading to the dry pipe valve, deluge or preaction systems. With the Model A-2 PMD the air supply is a tank mounted compressor with a pressure control switch, or a Nitrogen supply equipped with a regulating device. With the Model B-i PMD, the air supply is an air compressor without a pressure control switch. An extra outlet connection is provided on all of the models for mounting an optional pressure gauge to moni- tor the outlet pressure. c. For 3-phase wiring, a listed and/or approved, properly sized magnetic motor starter with ap- propriate NEMA enclosure must be provided. The wiring of the pressure switch, motor starter, and air compressor must be in accordance with the National Electrical Code, or other appropri- ate standards. 0 S Model A-2 Pressure Maintenance Device with Model D Dry Pipe Valve Trim Model A-2 Pressure Maintenance / Device J Pressure Relief / Valve - From Owner'sOwner's Air Supply, Tank—Mounted Air Compressor or Nitrogen Supply Model D Dry Pipe Valve IN Standard Dry Pipe Valve Air Line Trim 25 1FGO5F Figure 4 Model B-i Pressure Maintenance Device with Model D Dry Pipe Valve Trim Electrical Signal To Compressor —* From Tar Air Comp Stan do 25 1FCO6F Figure 5 5. Model A-2 Pressure Maintenance Device with Model BX Dry Pilot Line Deluge Trim To Dry Pilot Line Pressure Switch Pressure Relief Valve - From Owners Air Supply, Tank-Mounted Air Compressor or Nitrogen Supply Model A-2 Pressure Maintenance Device Standard Dry Pilot Lin Deluge Trim Dry Pilot Line fl Model BX A Actuator Deluge 3 Valve 1 4 Figure 6 Model B-i Pressure Maintenance Device with Model BX Dry Pilot Line Deluge Trim Electrical Signal To Compressor To Dry Pressure Pilot Line Switch Pressure Relief Valve - __g-__J From Tankless Air Compressor Model B-i Pressure Maintenance Device Standard - Dry Pilot Line Deluge Trim Dry Pilot Line Actuator -,CD Model BX Deluge 10( Valve C I -J 25 IFGO8A Figure 7 1.1 F_ Model A-2 Pressure Maintenance Device with Model LDX Dry Pipe Valve Trim From Owner's Air Supply, Tank-Mounted Air Compressor or Nitrogen Supply Model A-2 --Pressure Maintenance Device = Model LOX Pressure Relief Check Valve Valve Model LOX Dry Valve Model LOX Actuator Dry Pipe Valve 25 IFGO9A Figure 8 Model A-2 Pressure Maintenance Device with Model DDX Dry Pilot Line Deluge Trim From Owner's Air Supply, Tank-Mounted Air Compressor or Nitrogen Supply Model A-2 Pressure Maintenance Device To Dry Pilot Line 00 00 ,..-Pressure Switch Model LP Dry Pilot Line Actuator (? Model ODX 1' Deluge Valve 251F070A Figure 9 7' Model B-i Pressure Maintenance Device with Model DDX Dry Pilot Line Deluge Trim Figure 10 Model A-2 Pressure Maintenance Device with Model DDX Dry Pilot Line Single Interlock Preaction Trim Model A-2 Pressure Maintenance flvc From Owner Tank—Mounted or Nitrog DDX Valve 25 1 F 12A Figure 11 S Pi Model A-2 Pressure Maintenance Device with Model DDX Type F Double Interlock Preaction Trim From Owners Air Supply, Tank—Mounted Air Compressor or Nitrogen Supply 'l!O Model A-2 Pressure Maintenance Device 0 00 Model DDX Deluge Valve (:7) Model LP Dry Valve Actuator 25 IFC 13A Figure 12 Model A-2 Pressure Maintenance Device with Model DDX- LP Dry Pipe Valve Trim From Owner's Air Supply, Tank—Mounted Air Compressor or Nitrogen Supply Model A-2 Pressure Maintenance Device Model DDX Deluge Valve (2) Model LP -• Dry Valve Actuator / 251FG14A Figure 13 91 Reliabl e ... For Complete Protection *Reliable offers a wide selection of sprinkler components. Following are some of the many precision-made Reliable products that guard life and property from fire around the clock. Automatic sprinklers Flush automatic sprinklers Recessed automatic sprinklers Concealed automatic sprinklers Adjustable automatic sprinklers Dry automatic sprinklers Intermediate level sprinklers Open sprinklers Spray nozzles Alarm valves go Retarding chambers Dry pipe valves Accelerators for dry pipe valves Mechanical sprinkler alarms Electrical sprinkler alarm switches Water flow detectors Deluge valves Detector check valves Check valves Electrical system Sprinkler emergency cabinets Sprinkler wrenches Sprinkler escutcheons and guards Inspectors test connections Sight drains Ball drips and drum drips Control valve seals Air maintenance devices Air compressors Pressure gaugesldentification signs Fire department connection The equipment presented in this bulletin is to be installed in accordance with the latest published Standards of the National Fire Protection Association, Factory Mutual Research Corporation, or other similar organizations and also with the provisions of governmental codes or ordinances whenever applicable. Productsmanufactured and distributed by Reliable have been protecting life and property for over 90 years, and are installed and serviced by the most highly qualified and reputable sprinkler contractors located throughout the United States, Canada and foreign countries. Manufactured by *Reliable The Reliable Automatic Sprinkler Co., Inc. (800) 431-1588 Sales Offices (800) 848-6051 Sales Fax (914) 829-2042 Corporate Offices www.reliablesprinkler.com Internet Address Recycled @ - Paper Revision lines indicate updated or new data. EG. Printed in U.S.A 05/10 P/N 9999970040 F-30 (5-02) ;) - -s - - - -- - - --:-- --.' UL 2125 Listed Air Compressors Tankless / Tank Mounted 4LCB-46S-M4S0GX El UL 2125 Listed 0 Motor Mounted, (no belts or pulleys) 0 Oil free air, no lubrication required 0 Corrosion resistant internal parts 0 Compact, easy to install 0 Black Paint for easy identification Tank Mounted Model 4LCB-46T-M450GX A UNT OF WEX CORPORAPON www.gastmfg.com UL 2125 Listed El Motor mounted, (no belts or pulleys) Oil free air, no lubrication required Corrosion resistant internal parts Compact, easy to install O Black paint for easy identification MOTORS - All air compressors shown have open motors. Single phase motors have internal thermal protection. Dual voltage motors are shipped pre-wired for the higher voltage. (All tank units are wired for 115 volts) Model 4LCB-46S-M450GX Tankiess / Automatic air compressors have inlet filters, a safety valve, pressure switch (minimum switch differentials are 10-13 psig on most models) Check valve, tubing and fittings The 2LAF-46S-M200EX has 6 psig minimum differential. .UL Listed 2125 Oilless Piston Air Compressors for Dry Sprinkler Systems TANKLESS DIMENSIONAL DATA (IN.) Model Number A B C Pipe Size Ship Wt. 1LAA-46S-M100GX 603 14.66 8.31 114" NPT 22 5 2LAF-46S-M200EX 9.52 13.49 9.38 1/4" NPT 24.2 3LBA-468-M300GX 6.03 15.60 11.0 1/4" NPT 30:2 3LEM-46S-M345EX 7.71 14.96 9.40 114" NPT 29.2 LC13-46S44450GX 8.34 16.02 12.20 1/4" NPT 39.5 5LCA-46S-M550GX 8.34 17.15 12.25 1/4" NPT 47.5 6LCF-4684616EX 838 1969 1230 318 NPT 552 7LDE-46S-M750X 8.40 25.29 13.46 3/8" NPT 73.0 System to Pump Free Air Tankless Tank Mounted 40 PSI in 30 Mm. at 40 PSI Motor Data Packages Packages 90 tO 1/6 hp, 115-60-1 ILAA46S7M100GX 1LAA46T7M.1QOGX(2 GAL) 150 1.5 1/4 hp, 115-60-1 2LAF-46S-M200EX 2LAF-461-M200EX (12 GAL) 180 2.0 113 hp, 115-60-1 3LBA-46S-M300GX 3LBA-46T-M300GX (12GAL) 180 2.0 1/3 hp, 115-60-1 3LEM-46S-M345EX 3LEM-46T-M345EX (I2GAL) 300 3 1 1/2 hp 115/230-60-1 4LCB-46S M45OGX 4LCB-46T M4SOGX (20GAL) 400 4.2 3/4 hp, 115/230-60-1 5LCA-46S-M550GX 5LCA-46T-M550GX (20GAL) 600 5.9 1 hp 115/230 60 1 6LCF46S M616EX 6LCF-46T M6I6EX (30GAL) 800 7.9 1 1/2 hp, 115/208-230-60-1 7LDE-46S-M750X 7LDE46T-M750X (30GAL) I D Compressor Mounting Bracket Comes complete with all the hardware and adjustable stainless steel straps for mounting Gast tankless air compressors to all shapes and sizes of riser pipes. To order contact your local sprinkler supply company or your local Gas! distributor. Part Number AT670 UL Listed 2125 Oilless Piston Air Compressors for Dry Sprinkler Systems (Tank Units) Tank Package ASME Coded tank mounted compressors include gauge, pressure switch (minimum switch differential is 10-13 psig). Shut off valve, drain valve, check valve and safety valve. TANK UNITS DIMENSIONAL DATA (IN.) Tank Size Model Number A B C Pipe Size Gallon Ship Wt. 1LAA-46T-MI00GX 19 18 9 1/4" NPT 2 44.0 2LAF-46T-M2QOEX 26 21 13 114" NPT 12 78.0 3LBA-46T-M300GX 26 21 13 1/4" NPT 12 83.0 3LEM-46T-M345EX 2 6 21 13 1i4NPT 12 80.0 4LCB-46T-M450GX 33 26 17 1/4" NPT 20 109.0 5LCA46T-5503)( 33 26 17 114" NPT 20 115.0 6LCF-46T-M6I6EX 33 25.5 17 1/4" NPT 30 169.0 7LDE-46T-M750X 38 28.6 18 3/8" NPT 30 185.0 Air Capacity of a System Capacity of 1' of pipe (Based on actual internal diameter) Diameter Gallons 1/2 in. 0.16 3/4 in. .028 I in. .045 1 1/4 in. .078 11/2 1n. .106 2in. .174 21/2 in. .248 3 in. .383 3 in. .5t3 4 in. .660 Sip. 1.040 6in. 1.501 8 In. 2.66 S AJ550 Check Valve 1/4 NPT female AJ550A - Check Valve 3/8" NPT female AT670 Riser Mounting Bracket AK620 Pressure Switch (6 psig minimum pressure differential) AE- 163B - Pressure Switch cut-in pressure 40 psi, cut-out pressure 50 psi AF564 Pressure Switch (20 psig minimum pressure differential) AF631 Shok7isofation mounts 1/4:20 threaJ both ends (48 frame models 1 2, and 3) AF633 Shock/isolation mounts 5/16-18 thread (both ends) (48 & 56 frame) AF634 hose assy. 114" NPT fittings AH332 hose assy. 3/8" NPT fittings UL Fire Protection Listing UL File EX5324 Evaluated to UL2 125 Motor-operated air compressors for use in sprinkler systems. k Mounded Model i i \J 4LCB-46T-M450GX Accessories escription Gast Manufacturing Inc. World Headquarters 2550 Meadowbrook Rd. Benton Harbor, MI 49022 Ph: 269-926-6171 Fax: 269-926-8288 Eastern Sales Office 505 Washington Ave. Carlstadt, NJ 07072 Ph: 201-933-8484 Fax:201-933-5545 United Kingdom Beach House Knaves Beach Business Centre Loudwater, High Wycombe Bucks England HP10 9SD Ph: 44 (0) 1628-532600 Fax: 44(0) 1628-532470 Hong Kong Unit 12, 21/F, Block B New Trade Plaza 6, on Ping Street Shatin N.T. Hong Kong Ph: 852-2690-1008 Fax: 852-2690-1012 S JAS1T fl www.gastriifg.com S tqCU Fire & Building IProducts Technical Services: Tel: (800) 381-9312 I Fax: (800) 791-5500 Solenoid Valves For Deluge And I Electric Release General Description The Solenoid Valves For Releasing Service are intended for use with Tyco Fire Products Deluge and Preaction Valves which are to be electrically ac- tuated. The Solenoid Valves are used in conjunction with an electric releas- ing panel that is listed or approved (as appropriate) for fire protection releas- ing service, and where the releasing panel is operated by listed or approved (as appropriate) electric fire detectors. WARNING The Solenoid Valves described herein must be installed and maintained in compliance with this document, as well as with the applicable standards of the National Fire Protection Asso- ciation, in addition to the standards of any other authorities having jurisdic- tion. Failure to do so may impair the integrity of this device. The owner is responsible for maintain- ing their fire protection system and de- vices in proper operating condition. The installing contractor or sprinkler manufacturer should be contacted relative to any questions. raCtion Systems Service Technical Data Approvals UL Listed and CSA Certified under the name of Parker Hannifin Corporation, Skinner Valve Division. P/N 52-287-1- 024 (175 psi) and P/N 52-287-1-124 (250 psi) are FM Approved for release of Tyco Fire Products Deluge and Pre- action Valves. Working Water Pressure Refer to Figure 1. Physical Characteristics The body is brass, and the seal is Nitrile rubber. Operation Operation of an electrical device such as a heat sensitive thermostat, smoke detector, or electric manual pull station signals the releasing panel to energize the releasing circuit. Energizing the re- leasing circuit opens the normally closed de-energized Solenoid Valve to release water pressure from the differ- ential chamber of the deluge or preac- tion valve, which in turn permits the deluge or preaction valve to open and allow a flow of water into the system piping. chamber of the deluge or preaction valve, and the outlet port of the Sole- noid Valve is to piped to an open drain. For best life and optimum perform- ance the Solenoid Valve should be mounted vertically upright, as illus- trated in Figure 2, so as to minimize wear and reduce the possibility of ac- cumulating foreign matter. Step 3. Only apply pipe thread sealant sparingly to the male pipe threads of the connecting pipe nipples. Step 4. To prevent distortion of the Solenoid Valve body, always wrench on the portion adjacent to the pipe to which it is being connected. Do not use the Solenoid Valve to force a pipeline into position. Doing so may result in distortion of the valve. Installation The Solenoid Valves For Releasing Service are to be installed in accord- ance with the following instructions: Step 1. Check the nameplate for the correct catalog number, NEMA classi- fication, and voltage. Step 2. The Solenoid Valves are to be installed as part of the deluge or pre- action valve trim in accordance with the applicable instructions provided for the deluge valve or preaction valve. The inlet port of the Solenoid Valve is to be connected to the differential Step 5. Conduit and electrical connec- tions are to be made in accordance with the requirements of the authority having jurisdiction and/or the National Electric Code. The coil assembly may be reoriented, as necessary, by first loosening the nut on top of the coil. After repositioning the coil assembly, tighten the nut with a torque of 43 to 53 inch-pounds (4,9 to 6,0 Nm). NOTE Turn off electrical power before con- necting the Solenoid Valve to the power source. Page 1 of 4 JANUARY, 2003 TFP2I8O Page 2 of 4 TFP2IBO ENCLOSURE WORKING WATER AC VOLT-AMPS _______ DC TYPE VOLTAGE PRESSURE WATTS CATALOG P/N (a) INRUSH (b) HOLDING (NEMA RATINGS) PSI (BAR) AMPS 120 VAC, 60 Hz 20-175 10 31 16 73218BN4UNLVN0C111P3 52-287-1-110 110 VAC, 50Hz (1,4-12,1) 24 VDC 20-175 10 - - 0.41 73218BN4UNLVN0C111C2 52-287-1-024 (1,4-12,1) ORDINARY 24 VDC ____________ 20-250 22 - - (1,4-17,2) 0.83 732128N4TNLVN0C322C2 52-287-1-124 LOCATION 48 VDC 20-175 10 - - 0.21 73218BN4UNLVN0C111C4 52-287-1-048 (2, 4, and 4X) (1,4-12,1) 125 VDC 0-175 2 11 - - 0.08 73218BN4UNLVNOC1113N 52-287-1-125 (1,4-12,1) 250 VDC 20-175 10 - - 0.04 73218BN4UNLVN0C111N9 52-287-1-015 (1,4-12.1) 110/120 VAC 20-175 10 31 16 (1,4-12,1) - 73218BN4UNLVNOH111P3 52-287-1-210 HAZARDOUS 24 VDC ____________ 20-175 10 - - (1,4-12,1) 0.41 73218BN4UNLVNOH111C2 52-287-1-224 LOCATION (4, 4X, 7, and 9) 125 VDC 20-175 11 - - 0.08 73218BN4UNLVNOH1113N 52-287-1-225 (1,4-12,1) 250 VDC 20-175 10 - - 0.04 73218BN4UNLVNOH111N9 52-287-1-215 (14-12,1) - - NOTES: (a)Currant to start plunger moving. Current to hold plunger open. FIGURE 1 ENCLOSURE AND VOLTAGE RATINGS Care and Maintenance The following inspection procedure must be performed as indicated, in ad- dition to any specific requirements of the NFPA, and any impairment must be immediately corrected. The owner is responsible for the in- spection, testing, and maintenance of their fire protection system and de- vices in compliance with this docu- ment, as well as with the applicable standards of the National Fire Protec- tion Association (e.g., NFPA 25), in addition to the standards of any authority having jurisdiction. The in- stalling contractor or product manufac- turer should be contacted relative to any questions. It is recommended that automatic sprinkler systems be inspected, tested, and maintained by a qualified Inspection Service. NOTES Before closing a fire protection system control valve for inspection or mainte- nance work on the fire protection sys- tem which it controls, permission to shut down the effected fire protection system must first be obtained from the proper authorities and all personnel who may be affected by this action must be notified. After placing a fire protection system CONDUIT CONNECTION 3-13/16 I" ELEA 4-3/8" LEADS (111,1 mm) + 2-5/8 " 1/2"NPT (TYPICAL) 2 9/16" (66,7 mm) (65,1 mm) 175 PSI (12,1 BAR) MAXIMUM SERVICE PRESSURE NDUIT LIT CONNECTION ELECTRICAL I ) (TYPICAL) 2-3/4" 2" (69,9 mm) (50,8 mm) 250 PSI (17,2 BAR) MAXIMUM SERVICE PRESSURE FIGURE 2 SOLENOID VALVES FOR RELEASING SERVICE TFP2I8O Page 3 of 4 in service, notify the proper authorities and advise those responsible for moni- toring proprietary and/or central sta- tion alarms. INSPECTION PROCEDURE The Solenoid Valves must be in- spected quarterly in accordance with the following instructions: Verify operation of the Solenoid Valve following the procedure outlined in the Technical Data Sheet for the Tyco Fire Products Deluge or Preaction Valve. In general, if the voltage to the coil is correct, sluggish valve operation, ex- cessive leakage, or noise will indicate that cleaning is required. Clean the Solenoid Valve in accordance with the procedures outlined by Honeywell, Inc. Skinner Valve. Causes of Improper Operation Faulty Control Circuit: Check the electrical system by energizing the releasing circuit to the Solenoid Valve. A metallic "click" signifies that the solenoid is operating. Absence of the "click" indicates loss of power supply. Check for loose or blown fuses, open-circuited or grounded coil, broken lead wires or broken splice connections. Burned-Out Coil: Check for open- circuited coil. Replace if necessary. Check supply voltage; it must be the same as specified on label or name- plate. Low Voltage: Check voltage across the coil leads. Voltage must be at least 85% of nameplate rating. Limited Warranty Products manufactured by Tyco Fire Products are warranted solely to the original Buyer for ten (10) years against defects in material and work- manship when paid for and properly installed and maintained under normal use and service. This warranty will ex- pire ten (10) years from date of ship- ment by Tyco Fire Products. No war- ranty is given for products or components manufactured by compa- nies not affiliated by ownership with Tyco Fire Products or for products and components which have been subject to misuse, improper installation, corro- sion, or which have not been installed, maintained, modified or repaired in ac- cordance with applicable Standards of the National Fire Protection Associa- tion, and/or the standards of any other Authorities Having Jurisdiction. Mate- rials found by Tyco Fire Products to be defective shall be either repaired or replaced, at Tyco Fire Products' sole option. Tyco Fire Products neither as- sumes, nor authorizes any person to assume for it, any other obligation in connection with the sale of products or parts of products. Tyco Fire Products shall not be responsible for sprinkler system design errors or inaccurate or incomplete information supplied by Buyer or Buyer's representatives. IN NO EVENT SHALL TYCO FIRE PRODUCTS BE LIABLE, IN CON- TRACT, TORT, STRICT LIABILITY OR UNDER ANY OTHER LEGAL THE- ORY, FOR INCIDENTAL, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LABOR CHARGES, RE- GARDLESS OF WHETHER TYCO FIRE PRODUCTS WAS INFORMED ABOUT THE POSSIBILITY OF SUCH DAMAGES, AND IN NO EVENT SHALL TYCO FIRE PRODUCTS' LI- ABILITY EXCEED AN AMOUNT EQUAL TO THE SALES PRICE. THE FOREGOING WARRANTY IS Ordering Information Orders for the Solenoid Valves must include the description and Part Number (P/N). Solenois Valves: Specify: (Specify voltage), (Specify 175 or 250) psi pressure rating, Sole- noid Valve with (specify ordinary or hazardous) location enclosure, P/N (specify from Figure 1). OF MERCHANTABILITY AND FIT- NESS FOR A PARTICULAR PUR- POSE. 0 n Page 4 of 4 TFP2I8O C TYCO FIRE PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446 S tqCo /Fire & Building / )Products Technical Services: Tel: (800) 381-9312/ Fax: (800) 791-5500 Tyco Fire Products Model CV-IFR Riser Check Valve General Description The Tyco® Model CV-1 FIR Riser Check Valve is a compact and rugged swing- type unit that allows water flow in one direction and prevents flow in the op- posite direction. A resilient elastomer seal facing on the spring loaded clap- per ensures a leak tight seal and non- sticking operation. The Model CV-1FR Riser Check Valves are designed to minimize water hammer caused by flow reversal. The CV-1 FR is furnished with grooved ends and can be installed using Grin- nell® Grooved Couplings or Grinnell Figure 71 Flange Adapters. The Model CV-1 FR Riser Check Valves have been designed with a removable cover for ease of field maintenance. Valves in- stalled horizontally or inclined (flow up or down) are to be positioned with the cover facing up. Valves installed verti- cally may be positioned with flow up or down. The Model CV-1FR Riser Check Valve is provided with threaded outlets for pressure gauges and a drain connec- tion to facilitate their use in wet type automatic sprinkler system risers. They provide a more compact and econom- ical alternative to an alarm check valve where a water motor alarm is not re- quired. Provisions must be made for a local alarm, using an approved flow switch (not included). The Model CV-1FR Riser Check Valves are a redesignation for the Central Fig- ure 590FR and Grinnell Figure 590FR. NOTICE The Model CV-1FR Riser Check Valve described herein must be installed and maintained in compliance with this document and with the applica- ble standards of the National Fire Pro- tection Association, in addition to the standards of any authorities having ju- risdiction. Failure to do so may impair the performance of this device. The owner is responsible for maintain- ing their fire protection system and de- vices in proper operating condition. The installing contractor or manufac- turer should be contacted with any questions. Technical Data Sizes- Inches / DN 2 to 12 / DN50 to DN300 Maximum Working Pressure 300 psi (20,7 bar) Approvals UL, FM, and C-UL. Protective Coating Valve assembly Non-lead paint Installation The Model CV-1 FR Riser Check Valves are to be installed in accordance with the following instructions: Step 1. The arrow cast on the Body must point in the direction of the flow. Step 2. Valves installed vertically may be positioned with the flow up or down. Step 3. Valves installed horizontally or inclined (flow up or down) are to be positioned with the Cover facing up. Step 4. Grooved end pipe couplings used with the CV-1F must be installed in accordance with manufacturer's instructions. Care and Maintenance The owner is responsible for the in- spection, testing, and maintenance of their fire protection system and devic- es in compliance with this document, as well as with the applicable stan- dards of the National Fire Protection Association (e.g., NFPA25), in addition to the standards of any authority hav- ing jurisdiction. The installing contrac- tor or product manufacturer should be contacted relative to any questions. Any impairments must be immediately corrected. Automatic sprinkler systems should be inspected, tested, and maintained by a qualified Inspection Service in accor- dance with local requirements and/or national codes. After placing a fire protection system in service, notify the proper authorities and advise those responsible for mon- itoring proprietary and/or central sta- tion alarms. Page 1 of 6 JULY, 2008 TFP95O S S Page 2 of 6 TFP95O A 1/4" B 'I NPT L D (0 J - F Nominal Pipe Size Nominal Dimensions- Inches (mm) Cover Bolt Torq. Approx, Weight ANSI O.D. Inches Inches A B C D E F J K NPT Lbs,-ft, (Nm) Lbs. (kg) DN (mm) 2 2.375 6.75 4.38 2.55 2.57 3.25 15 9.0 1 18 9.0 DN50 (60,3) (171,5) (111,3) (64,8) (65,3) (82,3) (21) (4,5) (25) 4,5) 21/2 2.875 8.00 5.42 3.41 3.09 3.88 39 10.0 1-1/4 39 10.0 0N65 (73,0) (203,2) (136,7) (86,6) (78,5) (98,6) (54) (4,5) (54) (4,5) - 3.000 8.00 5.42 3.41 3.09 3.88 39 10.0 1-1/4 39 13.0 DN65 (76,1) (203,2) (136,7) (86,6) (78,5) (98,6) (54) (4,5) (54) (4,5) 3 3.500 8.38 5.76 3.60 3.31 3.88 39 11.0 1-1/4 39 11.0 DN80 (88,9) (212,9) (146,3) (91,4) (84,1) (98,6) (54) (5,0) (54) (5,0) 4 4.500 9.63 6.74 4.61 3.63 4.53 39 25.0 2 50 25.0 DN100 (114,3) (245,6) (171,2) (117,1) (92,2) (115,4) (54) (11,3) (69) (11,3) - 5.500 10.50 7.50 5.29 4.13 4.90 39 29.0 2 39 29.0 DN125 (139.7) (266,7) (190,5) (134,4) (104,9) (124,5) (54) (13,2) (54) (13,2) 5 5.563 10.50 7.50 5.29 4.13 4.90 39 29.0 2 39 29.0 DN125 (141,3) (266,7) (190,5) (134,4) (104,9) (124,5) (54) (13,2) (54) (13,2) - 6.500 11.50 8.05 5.75 4.50 5.00 60 47.0 2 60 47.0 DN150 (165.1) (292,1) (204,4) (146,1) (114,3) (127,0) (82) (21,3) (82) (21,3) 6 6.625 11.50 8.05 5.75 4.50 5.00 60 47.0 2 60 47.0 DN150 (168,3) (292,1) (204,4) (146,1) (114,3) (127,0) (82) (21,3) (82) (21,3) 8 8.625 14.00 10.25 7.75 5.62 5.45 120 66.0 2 120 66.0 DN200 (219,1) (355,6) (260,4) (196,9) (142,7) (138,4) (164) (30,0) (164) 1 (30,0) 10 10.750 18.00 13.00 10.21 6.38 7.50 120 109.7 2 130 109.7 DN250 (273,1) (457,2) (330,2) (259,3) (162,1) (190,5) (164) (49,4) (178) (49,4) 12 12.750 21.0 14.28 11.31 7.26 7.62 120 151.0 2 130 151.0 DN300 (323,9) (533,4) (362,7) (287,2) (184,4) (193,5) (164) (68,0) (178) (68,0) FIGURE 1 NOMINAL DIMENSIONS MODEL CV-IFR RISER CHECK VALVES 0 1 TFP950 Page 3 of 6 S 8 8 f"d" 2"- 8" 2 10' -12" 75 (DN50-DN200) (DN250 - DN300) VIEW A 13 11 14,15 1), 18 1,15 SEE 125 13 6 TAIL B 2" -8" 10' -12" (DN5O-DN200) (DN250 - DNSOO) DETAIL B 4,15 17 16 Detail Part Material Qty - 1 Body Ductile Iron 1 2 Cover Ductile Iron 1 Cover Gasket Nitrile Rubber 1 Hex Cap Steel, Zinc AR Screw Plated - Clapper Stainless Steel 2"- 8" ______ 1 Clapper Ductile Iron 10-12" Detail Part Material Qty- 6 Clapper EPDM 1 Facing Grade "E" 7 Spring Stainless 1 Steel 8 Hinge Stainless 1 Shaft Steel Retaining Stainless AR Ring Steel Retention Stainless 1 Bolt Steel 12 Seal Ring Neoprene 1 Detail Part Material Qty. 13 Retaining Stainless 1 Disc Steel 14 Locknut Stainless Steel 15 Adhesive Thread Sealer AR 16 Name- Aluminum 1 - plate 17 Rivet Steel 2 18 Spacer Stainless 1 Steel 0 FIGURE 2 MODEL CV-1FR RISER CHECK VALVES 1.I. •i •aja a a, a, a • , aa a Ia (.1.1,11 4aI.I.Ia •1.1a isi .dll â••uuu ••••••I FA ii huH Now •w••U'A••20 IIHNMOM WA••••• r •••••Ur1• MEIN U••II MOM F MMM mmoomm SEENNE wuuur4uuI UVIlIIIIIIIIII•••V4 • MEN moil moll MOM OEM UUW4IuUmill lIlion II•IAIUuuIU•••U'4uIIIIIIlIflhIlWAIIUIAI••IUU I • • ,In •••If•u•uuuaU••BuuulrAuuuI•U• L. ______••Uu.rA.usrAU•uuuuiaui moons, _________•ur•uuI•rA•uuiilIiriuuiuuiiIWIuiAu••uuuuiA•uuuuuiWuii1uuuiiU• Emmons 'MMENIMMENO • • - r ' • .zonsomill moll ui UU•U • ligillommom , • • • '4 •••u•••••••UuuI'•UUI•SU•UYA•••U• i..i..u...u . UIiI•••••II•••U a a.______ • • mall a. a. mmmwmmommmmm -12.11.2121=002- E cc. 1.1. ,IaIaI,1aIai16 1aaa $11f off off .161 less off TFP95O Page 4 of 6 Nominal Pipe Size Nominal Dimensions- Inches (mm) ANSI O.D. E Inches Inches A B C 0 Inches DN (mm) NPT 2 2.375 6.75 6.50 3.25 10.13 1 DN50 (60,3) (171,5) (165,1) (82,6 (257,2) 21/2 2.875 8.00 6.56 3.88 11.13 1-1/4 DN65 (73,0) (203,2) (166,7) (98,6) (282,6) - - 8.00 6.56 3.88 11.13 11/4 DN65 (76,1) (203,2) (166,7) (98,6) (282,6) 3 3.500 8.37 6.81 3.88 11.13 1 - 1/4 DN80 (88,9) (212,6) (173,0 (98,6) (282,6) 4 4.500 9.63 7.75 3.88 13.25 2 DN100 (114,3) (244,6) (196,9) (98,6) (336,6) - - 10.50 8.25 5.00 13.81 2 DN125 (139,7) (266,7) (209,6) (127,0) (350,8) 5 5.563 10.50 8.25 5.00 13.81 2 DN125 (141,3) (266,7) (209,6) (127,0) (350,8) - - 11.50 8.56 5.00 14.13 2 DN150 (165,1) (292,1) (2175) (127,0)) (358,8) 6 6.625 11.50 8.56 5.00 14.13 2 DN150 (168,3) (292,1) (2175) (127,0) (358,8) 8 8.625 14.00 9.75 5.50 15.25 2 DN200 (219,1) (355,6) (247,7) (139,7) (387,4) FIGURE 4 NOMINAL DIMENSIONS RISER CHECK VALVE WITH TRIM COMPONENTS (AVAILABLE FOR 2"(DN50) - 8"(DN200) VALVES ONLY) 0 TFP95O Page 5 of 6 P/N 59-591-1-020 Riser Check Valve Size 2 Inch (DN50) NO. DESCRIPTION QTY. P/N 1 300 psi/ 2000kPa Water Pressure Gauge . . 2 92-343-1-005 2 1/4 Gauge Test Valve . .2 46-005-1-002 3 1/4 Plug .............2 CH 4 1 Angle Valve .........1 46-048-1-006 5 1/4 x2" Nipple ........1 CH 6 1/4 x 5" Nipple ........1 CH 7 1" x3" Nipple ..........1 CH P/N 59-591-1-030 Riser Check Valve Sizes 2-1/2 (DN65); 76,1 mm; 3" (DN80) NO. DESCRIPTION QTY. P/N 1 300 psi/ 2000 kPa Water Pressure Gauge . . 2 92-343-1-005 2 1/4" Gauge Test Valve . 2 46-005-1-002 3 1/4 Plug .............2 CH 4 1-1/4" Angle Valve ......1 46-048-1-007 5 1/4x2" Nipple ........1 CH 6 1/4"x5" Nipple ........1 CH 7 1-1/4 x3" Nipple.......1 CH P/N 59-591-1-080 Riser Check Valve Sizes 4" (DN100); 139,7 mm; 5" (DN125); 165,1 mm; 6" (DN150); 8" (DN200) NO. DESCRIPTION QTY. P/N 1 300 psi! 2000 kPa Water Pressure Gauge . . 2 92-343-1-005 2 1/4" Gauge Test Valve . . 2 46-005-1-002 3 1/4" Plug .............2 CH 4 2 Angle Valve .........1 46-048-1-009 5 1/4"x2" Nipple ........1 CH 6 1/4" x5" Nipple ........1 CH 7 2"x3" Nipple ..........1 CH NOTES: All Fittings and Nipples are galvanized (Standard Order). CH: Common Hardware. MAIN DRAIN VALVE (NORMALLY CLOSED) SUPPLY PRESSURE GAUGE FIGURE 5 MODEL C V-i FR RISER CHECK VALVE TRIM PARTS LIST [1 Page 6 of 6 TFP95O Limited Ordering Warranty Procedure C Products manufactured by Tyco Fire & Building Products (TFBP) are war- ranted solely to the original Buyer for ten (10) years against defects in mate- rial and workmanship when paid for and properly installed and maintained under normal use and service. This warranty will expire ten (10) years from date of shipment by TFBP. No warran- ty is given for products or components manufactured by companies not af- filiated by ownership with TFBP or for products and components which have been subject to misuse, improper in- stallation, corrosion, or which have not been installed, maintained, modified or repaired in accordance with applicable Standards of the National Fire Protec- tion Association, and/or the standards of any other Authorities Having Juris- diction. Materials found by TFBP to be defective shall be either repaired or re- placed, at TFBP's sole option. TFBP neither assumes, nor authorizes any person to assume for it, any other ob- ligation in connection with the sale of products or parts of products. TFBP shall not be responsible for sprinkler system design errors or inaccurate or incomplete information supplied by Buyer or Buyer's representatives. In no event shall TFBP be liable, in contract, tort, strict liability or under any other legal theory, for incidental, indirect, special or consequential dam- ages, including but not limited to labor charges, regardless of whether TFBP was informed about the possibility of such damages, and in no event shall TFBP's liability exceed an amount equal to the sales price. The foregoing warranty is made in lieu of any and all other warranties, ex- press or imDlied, including warranties of merchantability and fitness for a particular purpose. This limited warranty sets forth the ex- clusive remedy for claims based on failure of or defect in products, materi- als or components, whether the claim is made in contract, tort, strict liability or any other legal theory. This warranty will apply to the full ex- tent permitted by law. The invalidity, in whole or part, of any portion of this warranty will not affect the remainder. The Model CV-1 FR Riser Check Valves: Specify: (specify size) Model CV-1 FR Check Valve, P/N (specify) (DN50) Valves ..............59-590-1-020 2-1/2" (DN65) Valves ........... 59-590-1 -025 0N65 (76,1mm) Valves .......... 59-590-1-076 (DN80) Valves ..............59-590-1-030 (DN100) Valves..............59-590-1-040 DN125 (139,7) Valves ...........59-590-1-139 (DN125) Valves .............. 59-590-1 -050 DN150 (165,1) Valves ...........59-590-1-165 (DN150) Valves .............. 59-590-1 -060 8" (DN200) Valves .............59-590-1-080 10" (DN250) Valves.............59-590-1-100 12" (DN300) Valves ............59-590-1-120 The Model CV-1FR Riser Check Valve Trim: Specify: (specify size) Model CV- 1 FR Check Valve Trim Assembly, P/N (specify) (DNSO) Valves ...............59-591-1-020 2-1/2" (DN65) Valves ...........59-591-1-030 DN65 (76,1mm) Valves ..... . .... 59-591-1-030 (DN80) Valves ........... ...59-591-1-030 (DN100) Valves..............59-591-1-080 DN125 (139,7) Valves ...........59-591-1-080 (DN125) Valves..............59-591-1-080 DN150 (165,1) Valves ...........59-591-1-080 (DN150) Valves..............59-591-1-080 8" (DN200) Valves .............59-591-1-080 Replacement Valve Parts Specify: (specify description) for use with (specify size) Model CV-1 FR Check Valve, P/N (specify) (DN50) Valves Cover Gasket ...................976-705-01 Clapper Facing..................976-709-01 2-1/2" (DN65) Valves Cover Gasket ...................975-618-01 Clapper Facing..................975-621-01 (DN80) Valves Cover Gasket ...................975-618-01 Clapper Facing .................. 975-491 -01 (DN100) Valves Cover Gasket ...................975-120-01 Clapper Facing..................975-003-01 (DN125) Valves Cover Gasket ...................975-120-01 Clapper Facing..................975-219-01 (DNI50) Valves Cover Gasket ...................975-218-01 Clapper Facing ..................975-006-01 8" (DN200) Valves Cover Gasket ...................975-479-01 Clapper Facing ..................975-463-01 10" (DN250) Valves Cover Gasket ...................976-000-01 Clapper Facing..................975-977-01 12" (DN300) Valves Cover Gasket ...................976-472-01 Clapper Facing..................976-474-01 © 2008 TYCO FIRE & BUILDING PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446 S FireLock® Butterfly Valve LWO MEA: 276.99-E SERIES 705W WITH WEATHERPROOF ACTUATOR The Series 705W butterfly valve features an approved weatherproof actuator housing approved for indoor or outdoor use. It has a ductile iron body and disc with EPDM disc coating. The body is coated with a heat fused polyphenylene sulfide blend to meet FM requirements. Designed for fire protection services only. Series 705W valve is UL Listed and FM Approved for 300 psi/2065 kPa service. The Series 705W is also LPCB approved for 20 Bar and VdS approved for 16 Bar service. Contact Victaulic for details of agency approvals. WEATHERPROOF ACTUATOR Pre-wired supervisory switches that monitor the valve in the fully open position for all sizes. OPTIONAL SUPPLY-SIDE TAP Series 705W valves are available with a ½' NPT supply side tap designed to allow direct water supply connection to Victaulic FireLock actuated fire protection valves. See separate drawings below. This is an optional feature and must be clearly noted on all orders. MATERIAL SPECIFICATIONS Body: Ductile iron conforming to ASTM A-536, coated with polyphenylene sulfide blend. Disc: Ductile iron conforming to ASTM A-536, various grades, EPDM coated. Disc Coating: Grade "E" EPDM EPDM (Green color code). Temperature range —30°F to +230°F/-34°C to +110°C. Recommended for cold and hot water service within the specified temperature range plus a variety of dilute acids, oil-free air and many chemical services. UL classified in accordance with ANSI/NSF 61 for cold +86°F/+30°C and hot +180°F/+82°C potable water service. NOT RECOMMENDED FOR PETROLEUM SERVICES. Stem Bearings: Teflon impregnated fiberglass with stainless steel backing. Stem Bearing Nuts: Type 416 Stainless Steel. Tap Plug: Carbon steel, plated. 0-Ring: EPDM Bracket: Carbon steel, painted. Actuator: 21h - 8/65 — 200 mm: Bronze traveling nut on a steel lead screw, in a ductile iron housing. 10— 12/250 - 300mm: Steel worm and cast iron quadrant gear, in a cast iron housing. JOB/OWNER CONTRACTOR ENGINEER System No. Submitted By - Spec Sect Para- Location - Approved S www.victaulic.com vicTAuLic IS REGISTERED TRADEMARK OF VICTALLIC COMPANY. © 2008 ViCTAULiC COMPANY. ALL RIGHTS RESERVED.. REV H 4tauIacf 1018 I PS CARBON STEEL PIPE - FIRE PROTECTION VALVES 10.18 FireLock® Butterfly Valve SERIES 705W WITH WEATHERPROOF ACTUATOR DIMENSIONS - C®VS ILPCBI USTED , ii Ji,' 2½ 65 2.875 73.0 3.77 95.6 8.76 222.5 - 421 106.9 6.08 154.4 3.00 76.2 0.00 0.0 0.75 19.1 8.3 3.8 I 3.000 3.000 76.1 3.77 95.6 8.76 222.5 - 4.21 106.9 608 154.4 300 76.2 0.00 0.0 0.75 19.1 8.3 3.8 761 mm 3.500 88.9 3.77 95.6 9.40 0.08 238.8 2.0 4.21 106.9 6.08 154.4 3.00 76.2 0.00 0.0 0.75 19.1 8.9 4.0 3 80 4 100 4.500 114.3 4.63 117.6 10.84 0.07 275.3 1.8 6.01 152.7 6.98 177.3 3.00 76.2 0.73 18,5 1.13 28.7 14.9 6.8 5.500 139.7 5.88 149.4 1238 0.43 314.5 10.9 6.01 152.7 8.57 217.7 4.50 114.3 - 21.0 9.5 13 . mm 5.563 5.88 1238 0.43 6.01 8.57 4.50 21.0 5 125 141.3 149.4 314.5 10.9 152.7 217.7 114.3 - - 9.5 165.1 mm 6.500 165.1 5.88 149,4 13.41 1.00 340.6 25.4 7.51 190.8 9.32 236.7 4.50 114.3 1.60 40.6 1.88 47.8 26.5 12.0 6.625 168.3 5.88 149.4 13.41 1.00 340.6 25.4 7.51 190.8 932 236.7 4.50 1143 1.60 40.6 1.88 47.8 26.5 12.0 6 150 8 200J 8.625 219.1 533 135.4 16.50 1.27 419.1 32.3 965 245.1 10.98 278.9 6.30 160.0 0.00 0.0 0.68 17.3 43.0 19.5 -. 10 "1 250 10.750 273.0 6.40 162.6 19.14 1.72 486.2 43.7 1220 309.9 16.19 411.2 9.00 228.6 - - 80.0 36.3 12.750 323.9 6.50 165.1 21.54 2.66 547.1 67.6 14.25 362.0 1722 437.4 9.00 228.6 - 102.0 46.3 12 300 On Centerline * These dimensions apply only to a Series 705W Butterfly Valve with a ½-inch NPT, supply-side tap . To prevent rotation of valves, it is recommended that Series 705W be installed with Victaulic Style 07 Zero-Flex, Style 005 FirOLock, Style 009/009V FireLock EZ, or Style HP-70 Rigid Couplings. If Victaulic flexible couplings are used, additional support may be required. Valve must not be installed with disc in full open position. Disc must be partly closed so that no part is protruding beyond end of valve body. Victaulic grooved end butterfly valves are permitted for use with grooved end pipe (lPS) only. Not permitted for use with plain end (IPS) pipe. Series 705W valves are designed for ambient weather conditions as opposed to submersible service. II :tftf Iliii•i :iiil lull lII!!Il 'I'll' 111111' 2M-4-INCH/65- 100-MM SIZES 5 - 12-INCH/125 - 300-MM SIZES www.victaulic.com vICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 6) 2008 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 10.18 2 x. AC -ta U -h C: r REV H IPS CARBON STEEL PIPE - FIRE PROTECTION VALVES 10.18 FireLock® Butterfly Valve SERIES 705W WITH WEATHERPROOF ACTUATOR ------------ 0026 DIMENSIONS - C®US FL-PCB LISM jI I i 76.1 mm 3,000 3.77 8.76 4.21 6.08 76.1 95.6 222.5 - 106.9 154.4 4.50 1143 0.00 0.0 0.75 19.1 8.3 3.8 3 3.500 377 9.40 008 4.21 6.08 4.50 0.00 075 89 80 88.9 95.6 238.8 2.0 106,9 154.4 114.3 0.0 19,1 4.0 4 4.500 4.63 10.84 0.07 6.01 6.98 4.50 0.73 1.13 14.9 100 114.3 117.6 2753 1.8 152.7 1773 1143 18.5 28.7 6.8 39. 1 7mm 5.500 5.88 12.38 0.43 6.01 8.57 139.7 149.4 314.5 10.9 152.7 217.7 7.87 200 - - 21.0 9.5 6 150 6.625 5.88 13.41 1.00 7.51 9.32 168.3 149.4 340.6 25.4 190.8 236.7 7.87 200 1.60 40.6 1.88 47.8 26.5 12.0 8 8.625 5.33 16.50 127 9.65 10.98 7.87 0.00 0.68 43.0 200 219.1 135.4 419.1 32.3 245.1 278.9 200 0.01 173 19.5 10 10.750 6.40 19.14 1,72 12.20 16.19 9.84 80.0 250 273.0 162.6 486.2 43.7 309.9 411.2 250 - 363 12 12.750 650 21.54 2.66 14.25 17.22 9.84 102,0 300 323.9 165.1 547.1 67.6 362.0 437.4 250 - 46.3 On Centerline These dimensions apply only to a Series 705W Butterfly Valve with a 1/2-inch NPT, supply-side tap To prevent rotation of valves, it is recommended that Series 705W be installed with Victaulic Style 07 Zero-Flex° Style 005 FireLock, Style 009/009V FireLock EZ, or Style HP-70 Rigid Couplings. If Victaulic flexible couplings are used. additional support may be required. Valve must not be installed with disc in full open position. Disc must be partly closed so that no part is protruding beyond end of valve body. Victaulic grooved end butterfly valves are permitted for use with grooved end pipe (IPS) only. Not permitted for use with plain end (IPS) pipe. Series 705W valves are designed for ambient weather conditions as opposed to submersible service. !" .; 11.111 iliHil 76.1MM - 4-INCH/65 - 100-MM NOMINAL SIZES 31 1 !i" ••' •l• 11111k 11111k 'JW' Ilmill' , 1111111' . -...-- -..-... wwW.victaulic.com - VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2008 vicTAuLic COMPANY. ALL RIGHTS RESERVED. ictauIic REV H 10.18 3 PS CARBON STEEL PIPE - FIRE PROTECTION VALVES 10.18 FireLock® Butterfly Valve SERIES 705W WITH WEATHERPROOF ACTUATOR PERFORMANCE The chart expresses the frictional resistance of Victaulic Series 705W in equivalent feet/meters of straight pipe. MAXIMUM WORKINGS PRESSURE RATINGS S ......... www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2008 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 10 18 4 Ac--ta-ulicr REV H PS CARBON STEEL PIPE FIRE PROTECTION VALVES 10.18 FireLock® Butterfly Valve SERIES 705W WITH WEATHERPROOF ACTUATOR PERFORMANCE C, values for flow of water at +60°F/+16°C with a fully open valve are shown in the table below. For additional details, contact Victaulic. Formulas for Cv Values: = Q2 Where: Q = Flow (GPM) AP = Pressure Drop (psi) Q = C x C = Flow Coefficient Formulas for Kv Values: = Where: Q= Flow () O = K AP = Pressure (bar) = Flow Factor - 21 .J1iul 2½ 65 2.875 730 0 3 . mm 5.500 139.7 995 8 I 200 8.625 2940 219.1 76.1 mm 3.000 761 28 5 125 1 5.563 141.3 995 10 250 10.750 273.0 4975 3 80 3.500 889 415 165.1 mm 6.500 16 1600 12 300 12.750 323.9 7180 4 4.500 520 6 6.625 1600 100 1143 150 168.3 www.victaulic.com vicTAuLic Is A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2008 VICTAuLIC COMPANY. ALL RIGHTS RESERVED. REV H A.-c—taulid 10 18 5 IPS CARBON STEEL PIPE - FIRE PROTECTION VALVES 10.18 FireLock® Butterfly Valve . SERIES 705W WITH WEATHERPROOF ACTUATOR SWITCH AND WIRING The supervisory switch contains two, single pole, double throw, pre-wired switches. Switches are rated: 10 amps @ 125 or 250 VAC/60 Hz 0.50 amps© 125 VDC 0.25 amps © 250 VDC Switches supervise the valve in the "open" position. One switch has two #18 MTW wires per terminal, which permit complete supervision of leads (refer to diagrams and notes below). The second switch has one #18 MTW wire per terminal. This double circuit provides flexibility to operate two electrical devices at separate locations, such as an indicating light and an audible alarm, in the area that the valve is installed. A #14 MTW ground lead (green) is provided. Switch #1 = Si For connection to the supervisory circuit of a UL Listed alarm control panel Switch #2 = S2 Auxiliary switch that may be connected to auxiliary devices, per the authority having jurisdiction Normally Closed: (2) Blue Common: (2) Yellow Normally Closed: Blue with Orange Stripe S2 Normally Open: Brown with Orange Stripe Common: Yellow with Orange Stripe OSA AT 125 WC. OZATISOVDC 0 11 BELL Switd, 1:2leads per Iam,lnaI Swird, 2.r dperrrnr,neI NOTE: The above diagram shows a connection between the common terminal (yellow— 51 and yellow-with-orange stripe —S2) and the normally closed terminal (blue — Si and blue-with-orange stripe - S2). In this example, the indicator light and alarm will stay on until the valve is fully open. When the valve is fully open, the indicator light and alarm will go out. Cap off any unused wires (e.g. brown with orange stripe). Only Si (two leads per terminal) may be connected to the fire alarm control panel. The connection of the alarm switch wiring shall be in accordance with NFPA 72 and the auxiliary switch per NFPA 70 (NEC). . .. www.victaulic.com vicTAuLic IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2008 VIcTAUUc COMPANY. ALL RIGHTS RESERVED. 10:18 6 A-c-t a _U1 ii d REV H WItH VVtAtMRKUUE Mt.IURIUt( WARRANTY Refer to the Warranty section of the current Price List or contact Victaulic for details. --- - ------ NOTE This product shall be manufactured by Victaulic or to Victaulic specifications. All products to be installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations. INSTALLATION Reference should always be made to the installation sheet included with the valve. Verify you have the latest revision by visiting our website at www.victaulic.com. Further reference can be found in the -100 Victaulic Field Installation Handbook. C For complete contact information, visit www.victaulic.com 10.18 2466 REV H UPDATED 812008 VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 8 2008 VIcTAULIC COMPANY. ALL RIGHTS RESERVED. 1018 1111111111111111111111111111111111111111111111111 WCAS-71-I FF85 Jtauhc0 . .T . . . . . . . . . Ea1WA1Ii LI The AGF Manufacturing Inc. Model 1000 TESTANDRAIN Provides Both The Test Function And The Express Drain Function For A Wet Fire Sprinkler System. Li The Model 1000 Complies With All Requirements Of NFPA-1 3, NFPA-1 3R, And NFPA-13D. LI The Model 1000 TESTANDRAIN Is A Single Handle Ball Valve That Is Light Weight And Compact, Includes A Tamper Resistant Test Orifice, Integral Tamper Resistant Sight Glasses, And Is 300 PSI Rated. LI Available In A Full Range Of Sizes From 3/4" To 2" NPT & BSPT, With All Specifiable Orifice Sizes 3/8??, 7/16!?, 1/2", 17/32", 5/8" (ELO), & 3/4" (ESFR). LI The Orifice Size Is Noted On The Indicator Plate And The Valve Is Tapped For A Pressure Gauge. U Locking Kit Available Which Provides Superior Vandal Resistance And Prevents Unintentional Alarm Activation. out New Visit us on the Internet at 10100 SIZE A B C D E F G H 3/4"" 5 1/v.." 1 1/211 2 I16" 3 'a" 3 /8" 1 13/loll 4 Il6" 6 /8" 128mm 37.58mm 55.65mm 93.23mm 85.88mm 45.30mm 117.12mm 162.42mm 1" 5 1/16!! 1 1/f 2 /io" 3 'a" 3 /8" 1 13/16!! 4 Iio" 6 3/5" 128mm 37.58mm 55.65mm 93.23mm 85.88mm 45.30mm 117.12mm 162.42mm 1 1," 5 /io" 1 11/1611 2 9/1611 4 1/4"3 I16" 1 151 " 5 Iio" 5 1/2!! 4 137.70mm 42.70mm 65.36mm 108.36mm 82.84mm 50.89mm 141.39mm 192.28mm 1, " 6 I16" 1 13/16!! 3 1/4'! 5 1/16'! 3 7/811 2 5/se 8 1/4!! 10 I8" I '2 163.38mm 45.50mm I 81.50mm 127mm 99.18mm I 66.97mm 206.63mm 273.60mm L1 2" 6 /io" 1 13/16!' 3 1/411 5 1/16!! 3 7/s" 2 5/5" 8 1/4" 10 I8" 163.38mm 45.50mm 81.50mm 127mm 99.18mm 66.97mm 206.63mm 273.60mm MATERIAL LIST PART: MATERIAL: HANDLE STEEL STEM ROD BRASS BALL CA BRONZE BODY BRONZE VALVE SEAT IMPREGNATED TEFLON INDICATOR PLATE STEEL HANDLE LOCK SPRING STEEL 300 PSI 3/4" 111 1 1/4" 1 1/2" 211 Li PLAN VIEW FRONT VIEW/VERTICAL INSTALLATION FRONT VIEW/HORIZONTAL INSTALLATION ORIFICE SIZE AVAILABLE - 3/8, 7/16, 1/2, 17/32, ELO(5/8), ESFR(3/4)' DIMENSIONS - INCHES FROM BRANCH ,*GAUVGI INLET ED STREET EL TO DRAIN I - STREET EL OR PIPE ' I TO DRAIN RIGHT HAND/STRAIGHT INSTALLATION APPROVALS: Cl UL and ULC Listed U FM Approved except 3/4" U NYC-BSA NO. 720-87-SM U CA, State Fire Marshall *Available on 11/4" to 2" size units only. -3/4"UL Listed only. L ........... ------- .. .. UI LISTING EX4019 I I AGF MANUFACTURING INC. JOB NAME: 100 Quaker Lane Malvern, PA 19355 USA Telephone: (610) 240-4900 ENGINEER Fax: (610) 240-4906 www.testandrain.com MADE IN U.S.A. CONTRACTOR: 1-lecessed Horizontal Sidewall Bulletin 014 Rev. G Model Fl FR56 Series Quick Response Standard Spray ED CD 0 CD Model F1 FR56 Sprinkler Types Standard Upright Standard Pendent Conventional Vertical Sidewall Horizontal Sidewall Model Fl FR56 Recessed Sprinkler Types Standard Pendent/F1/F2/FP Horizontal Sidewall Ujfight. Pendent C) Vertical Sidewall Model Fl FR56 Concealed Sprinkler Types Standard Pendent Listing & Approvals Underwriters Laboratories Inc. and Certified for Canada (cULus). Factory Mutual Approvals (FM) Loss Prevention Council (LPCB, UK) VdS Schadenverhutung GmbH UL Listing Category ..Sprinklers, Automatic & Open (VNlV) Quick Response Sprinkler Product Description Reliable Models F1FR56 Series Sprinklers are quick re- sponse sprinklers which combine the durability of a stan- dard sprinkler with the attractive low profile of a decorative sprinkler. The Models F1FR56 Series Recessed automatic sprin- klers utilize a 3.0 mm frangible glass bulb. These sprin- klers have demonstrated response times in laboratory tests which are five to ten times faster than standard response sprinklers. This quick response enables the Model F1FR56 Series sprinklers to apply water to a fire much faster than standard sprinklers of the same temperature rating. The glass bulb consists of an accurately controlled amount of special fluid hermetically sealed inside a precisely manu- factured glass capsule. This glass bulb is specially con- structed to provide fast thermal response. At normal temperatures, the glass bulb contains the fluid in both the liquid and vapor phases. The vapor phase can be seen as a small bubble. As heat is applied, the liquid expands, forcing the bubble smaller and smaller as the liq- uid pressure increases. Continued heating forces the liquid to push out against the bulb, causing the glass to shatter, opening the waterway and allowing the deflector to distrib- ute the discharging water. r. Conventional Horizontal Sidewall Concealed ecessea Pendent Pendent/FP Application Quick response sprinklers are used in fixed fire protec- tion systems: Wet, Dry, Deluge or Preaction. Care must be exercised that the orifice size, temperature rating, deflec- tor style and sprinkler type are in accordance with the lat- est published standards of the National Fire Protection As- sociation or the approving Authority Having Jurisdiction. Quick response sprinklers are intended for installation as specified in NFPA 13. Quick response sprinklers and stan- dard response sprinklers should not be intermixed. The Reliable Automatic Sprinkler Co., Inc., 103 Fairview Park Drive, Elmsford, New York 10523 Model Fl FR56 Quick Response Upright, Pendent & Conventional Sprinklers Installation Wrench: Model D Sprinkler Wrench Installation Data: I I Sprinkler Identification Number Nominal Thread Nominal K Factor j Sprinkler Approval (SIN) P Orifice Size i— —1 Height Organization Metric Upright - Pendent Standard-Upright (SSU) and pendent Deflectors Marked to Indicate Position ½__(15mm) NPT(R½Yj 56[ 80 57rnmti34 iR1425J RA1414 i2 Conventional-Install in Upright or Pendent Position 15mm11 I ½" NPT('/2) 5.6 80 57mm 3,4 I RA1475 i cULus listed corrosion resistant (Polyester coated) sprinkler Polyester coated FM approved sprinkler. Wpriht Pendent Conventional odel Fl FR56 Quick Response Recessed Pendent Sprinkler tallatlon Wrench: Model GFR2 Sprinkler Wrench stallationData: Nominal Orifice Thread Size KFactor Sprinkler Height Sprinkler Identification Number (SIN) US Metric ½___ NTQ1) t5 6 Q 127gmji Refer to escutcheon data table for approvals and dimensions. 2 I/4 HOLE 01& (57.2,n,,] I I5/16 014 - r S I/2 REDUCER TURN COLLAR UNTIL LIGHT AGAINST SPRINKLER I WRENCH BOSS / 1 FACE OF FITLWC TO ADJUSTMENT v CEILING DIMENSION .11.11) 2 27/32 014. 014F001 [72.2rnn,J REFER TO FL & PS ESCUTCHEON OATA TABLE FOR APPROVALS AND DIMENSIONS. Model F1FR56/F1 or F2 U— 2 5/8" 0/A. (66.7mm] —j HOLE IN CEILING 2 5/16" 014. (58.7mm] - CUP K I/i" REDUCER / I / CEILING 009 FACE OF AmNO TO FACE OF CEILING .4oJusTMEN;' PTT A (I) REFER TO PP ESCUTCHEON DATA TABLE FOR APPROVALS AND DIMENSIONS, Model F1FR56IFP 2. Fl FR56 Quick Response Vertical Sidewall Sprinkler Lion Wrench: Model D Sprinkler Wrench Lion Position: Upright or Pendent all Type: Light Hazard Occupancy Ron Data: Nominal K Factor Jominal Thread Size Orifice US Metric (15mm) ½" NPT(R1/2) 5.6 8.0 15mm 1'%.i" NPT(R1/2) 5,6 8.0 LPC Approval is for penpt position only. cULus Listed corrosion retant (Polyester coated) sprinkler. Sprinkler Height 2.25 (57mm) 2.25" (57mm) Approval Organizations 12.3,4 401 Sprinkler Identification Numbers (SIN) RA 1485U' Sprinkler Tyne" Deflector to Ceiling Distance / (Mm. - Max.) Uprigh/ 4" (102mm) - 12" (305mm) Pen 'nt 4" (102mm) - 12" (305mm) Vertical Sidewall Model Fl FR56 Quick Response Horiz Deflector: HSW Installation Wrench: Model D Sprinkler Wrench Installation Data: Horizontal Sidewall Sidewall sprinkler Nominal K Factor Sprinkler Approval Organizations I Sprinkler \ight and Type of Approval Nominal Orifice Thread Size I Identification US Meic ,/J4t// Light Hazard Ordinary I Numbers (SIN) Hazard ½" (15mm) ½" NPT CR1/2) 5.6 80 2.63"m) 1,2 1 1 RA1435' cULus Listed corrosion resistant (Polyester coated) , 7kler. FACE OF FITTING' TO FACE OF CEILING DIMENSION • I 1 1/4" MIN. (31.8mm] I -2 1/4" HOLE 014. 1/8" 4"- 12" (2) [57.2mm] 2mm] [101.6mm-304.8mm] CEILING TO l",\1/2" REDUCER7 DEFLECTOR 1 75/16" OIA.yI Horizontal Sidew [49.2mm] .32" 0/A. [7 mm] TURN COLLAR UNTIL TIGHT AGAINST SPRINKLER WRENCH BOSS. (1) ADJUSTMENT OIJFGO38 . (1) REFER TO ESCUTCHEON DATA TABLE FOR APPROVALS AND DIMENSION (2,) FM APPROVED FOR 4" - 6" [101.6MM - 152.4MM] CEILING TO DEFLE R. Note: For Recessed HSW Sprinklers use installation wrench G 3' I xel Fl FR56 Quick Response Concealed Pendent Sprinklers instal "on Wrench: Model RO1 Sprinkler Wrench TechnicaFta: • Nominal actor Thread rea 1 TT" Temp. Rating Max. l r - U ,/ Sprinkler Drifice Model US Ambient Color I Sprinkler Cover_— A ro"ls Identification Temp Number(SI N) 1/2 ' (15mm) 5.6 80"PT F1 FR 135F/57°C 135'FI57'C 100'f/38'0 Orange 1 RA1414 ½' (15mm) 5,6 80 '/ PT F1 FR 155°F/68'C 135°F/57-C 100F/38°C 1 40.__- PA1414 ½" (15mm) 5.6 80 ½' NFl F1FR i75°F/79C 165-17/74°C 1 10017/38°9/i'Yellow 1 14 ½" (15mm) 5.6 80 ½" NFl Fl 200"F/93"C 165°F/74°C 150°'C Green 1 RA1414 1/ For VdS only = 155°F/68°C Norbulb and 1/2' [12, 1 x 1,'2" REDUCING TEE OR ELBOW -2 5/8" DIA. 2 5/16" 0/A -1 11 HOLE IN C NG CUP 1 1/2" MAX. FACE OF FITTING CEILING TO FACE OF CEILING , z1 DIMENSION '''',''.4 $ 1 - 1/2" MAX. 15/16" COVER ADJUSTMENT COVER PLATE - ASSEMBLY 3 5/16 0/A. SPRINKLER 1/2" ADJUSTMENT Figure 1 TnstaUation Aid A protective cap is included for use during installation, Important: The F1FR56 Sprinkler with Model COP cover plate is not an FM Approved combination. Installation Quick response sprinklers are intended for installation as specified in NFPA 13. Quick response sprinklers and standard response sprinklers should not be intermixed, The Model F1FR56 Recessed Quick Response Sprin- klers are to be installed as shown, The Model Fl or F2 Es- cutcheons illustrated are the only recessed escutcheons to be used with the Model F1FR56 Sprinklers. The use of any other recessed escutcheon will void all approvals and negate all warranties. When installing Model F1FR56 Sprinklers, use the Mod- el D Sprinkler Wrench. Use the Model GFR2 Wrench for installing F1FR56 Recessed Pendent Sprinklers. Any other type of wrench may damage these sprinklers. NOTE: A leak tight V2" NPT (R112) sprinkler joint can be obtained with a torque of 8-18 ft-lbs (10,8 - 24,4 N-m). Do not tighten sprinklers over maximum recommended torque. It may cause leakage or impairment of the sprin- klers. The Model Fl FR56/ COP Concealed Sprinkler uses the .' orifice, ½" NPT (R112), 135°F (57°C), 155°F (680C), 5°F (79°C) or 200°F (93°C) Model Fl FR56 Pendent 1/2' REDUCING TEE OR ELBOW 2 5/8" 0/A. 2 5/i 6'\QIA - +-/------.4 HOLE IN CEILING ' - CUP 1 1/2" MAX. FACE OF FITTING -------1 TO FACE OF CEILING DIMENSION - CEILING-' q 5/16" MAX. 3/4" COVER ADJUSTMENT I COVER PLATE-I ASSEMBLY ............ 3 5/16" 0/A SPRINKLER / 5/16" ADJUSTMENT Figure 2 Sprinkler with a threaded Model COP cup which is fac- tory attached to the sprinkler. The assembly is complet- ed by the installation of the attractive, low profile, 135°F (57°C) or 165°F (74°C) rated Model COP push on cover plate assembly. The cover plate and sprinkler cup as- semblies are joined using a cover plate skirt with flexible tabs for threaded engagement. A choice of two cover plate assemblies provide either ½" (13mm) or /16" (8mm) of cover adjustment. Do not install these sprinklers in ceiling which have positive pressure in the space above. After a 2/8" (67mm) diameter hole is cut in the ceil- ing, the sprinkler is easily installed with the Model RO1 Wrench. A Teflon* based thread sealant should be applied to the sprinkler threads only. The Model RC1 Wrench is then used to engage the sprinkler wrenching surfaces and to install the sprinkler in the fitting. When inserting or removing the wrench from the sprinkler/cup assembly, care should be taken to prevent damage to the sprinkler. DO NOT WRENCH ON ANY OTHER PART OF THE SPRINKLER. The cover plate is then pushed onto the cup. Final adjustment is made by hand turning the cover plate until the skirt flange makes full contact with the ceiling. Cover plate removal requires turning in the counter clockwise direction. *DuPont Registered Trade Mark 4. After installation, inspect all sprinklers to ensure that there is a gap between the cover plate and ceiling and that the four cup slots are open and free from any air flow impediment to the space above. Temperature Ratings Classification Temperature I Temp. Bulb Color Sprinkler 1 Max. Ambient I OC OF Ordinary 57 1 135 t 100°F (38°C) Orange Ordinary 68 155 100°F (38°C) Red Intermediate 79 175 150°F (66°C) Yellow Intermediate 93 200 150°F (66°C) I Green High 1) 141 I 286 225°F (107°C) Blue Not available for recessed sprinklers. Escutcheon Data (') Escutcheon "A" Face of Fitting to Model Exrnension Approvals Adjustment Ceiling or Wall Dimension Fl 1,3,4 Max Recess 11/2" (38.1mm) I Min Recess /4"(19.1rnn) (5mm-24n-m) F2 1,2 3,4 Max Recess 1 1/2" (38.lrrm) Min Recess 1" (25mm) (5mm - 17rrni) FPPush-orV Max Recessed '/i"(11rrrn) 11k' (38.1rrrn) 1,4 Thread-off MinRecessed /ic (24nTn) 1" (25.4mm) SIN RA1435 - cULus permits use with Fl F2 or FP escutcheons for "light hazard" only while FM limits use for same hazard with F2 escutcheon only Maintenance The Models F1FR56 and F1FR56 Recessed Sprinklers should be inspected quarterly and the sprinkler system maintained in accordance with NFPA 25. Do not clean sprinklers with soap and water, ammonia or any other cleaning fluids. Remove dust by using a soft brush or gentle vacuuming. Remove any sprinkler which has been painted (other than factory applied) or damaged in any way. A stock of spare sprinklers should be main- tained to allow quick replacement of damaged or oper- ated sprinklers. Prior to installation, sprinklers should be maintained in the original cartons and packaging to mini- mize the potential for damage to sprinklers that would cause improper operation or non-operation. Sprinkler Types Standard Upright Standard Pendent Conventional Recessed Pendent Vertical Sidewall Horizontal Sidewall Recessed Horizontal sidewall Concealed pendent Maximum Working Pressure 175 psi (12 bar) 100% Factory tested hydrostatically to 500 psi (34.5 bar) Finishes (1) Standard Finishes Sprinkler Escutcheon Cover plate Bronze Brass Chrome Plated Chrome Chrome Polyester Plated White Coated (1)(5) 1 WhitePainted Special Application Finishes Sprinkler Escutcheon Coverplate Bright Brass Bright Brass Bright Brass Black Plated Black Plated Satin Black Paint (2) Black Paint Off White Off White (2) Off White Black Paint SatinChrome I SatinChrome BlackPlated Other finishes and colors are available on special order. Consult the factory for details. cULus Listed only. 200°F (93°C) maximum. cULus listed "corrosion resistance' applies to SIN Numbers RAJ 435 (HSW), RA1485(VSW), RA1425 (Upright) and RA1414 (Pendent) in standard black or white. FM Approvals finish as "Polyester coated" applies to SIN Number RA1414 (Pendent) in standard black or white. Ordering Information Specify: Sprinkler Model Sprinkler Type Orifice Size Deflector Type Temperature Rating Sprinkler Finish Escutcheon Type Escutcheon Finish (where applicable) Cover plate Model Cover plate Thread size Cover plate Temperature Cover plate Adjustment Cover plate Finish Note: When Model F1FR56 Recessed sprinklers are ordered, the sprin- klers and escutcheons are packaged separately. .Concealed cover plate/cup assemblies are listed only for use with specific sprinklers. The use of any other con- cealed cover plate/cup assembly with the Model Fl FR56 Pendent Sprinkler or the use of the Model CCP Concealed cover plate assembly on any sprinkler with which it is not specifically listed my prevent good fire protection and will void all guarantees, warranties, listings and approvals. Glass bulb sprinklers have orange bulb protectors to minimize bulb damage during shipping, handling and installation. REMOVE THIS PROTECTION AT THE TIME THE SPRINKLER SYSTEM IS PLACED IN SERVICE FOR FIRE PROTECTION. Removal of the protectors before this time may leave the bulb vulnerable to damage. RASCO wrenches are designed to install sprinklers when covers are in place. REMOVE PROTECTORS BY UNDOING THE CLASP BY HAND. DO NOT USE TOOLS TO REMOVE THE PROTECTORS. 5. RaH'aWe...Far Comp~ete Pratedfo3 an Reliable offers a wide selection of sprinkler components. Following are some of the many Oecision-made Reliable products that guard life and property from fire around the clock. Automatic sprinklers Flush automatic sprinklers Recessed automatic sprinklers Concealed automatic sprinklers Adjustable automatic sprinklers Dry automatic sprinklers Intermediate level sprinklers Open sprinklers Spray nozzles Alarm valves 0 Retarding chambers Dry pipe valves Accelerators for dry pipe valves Mechanical sprinkler alarms Electrical sprinkler alarm switches Water flow detectors Deluge valves Detector check valves Check valves Electrical system Sprinkler emergency cabinets Sprinkler wrenches Sprinkler escutcheons and guards Inspectors test connections Sight drains Ball drips and drum drips Control valve seals Air maintenance devices Air compressors Pressure gauges Identification signs Fire department connection The equipment presented in this bulletin is to be installed in accordance with the latest published Standards of the National Are Protection Association, Factory Mutual Research Corporation, or other similar organizations and also with the provisions of governmental codes or ordinances whenever applicable. Products manufactured and distributed by Reliable have been protecting life and property for over 90 years, and are installed and serviced by the most highly qualified and reputable sprinkler contractors located throughout the United States, Canada and foreign countries, anufactured by The Reliable Automatic Sprinkler Co. Inc. Recycled MGM (800) 431-1588 Sales Offices ' Paper (800) 848-6051 Sales Fax Revision lines indicate updated or new data. (914) 829-2042 Corporate Offices -_-__- www.reliablesprinkler.com Internet Address EG. Printed in U.S.A 08/11 P/N 9999970300 SCHEDULE 10 SPECIFICATIONS NOMINAL NOMINAL NPS NOM OD NON ID WALL WEIGHT UL PIECES In. mm in. mm in. mm ibs./ft. kg/rn CRR* Lift 1¼ 1.660 42.2 1.442 36.6 .109 2.77 1.81 2.69 7.3 61 1% 1.900 48.3 1.682 42.7 .109 2.77 2.09 3.11 5.8 61 2 2.375 60.3 2.157 54.8 .109 2.77 264 3.93 4.7 37 2% 2.875 73.0 2.635 66.9 .120 3.05 3.53 526 3.5 30 3 3.500 88.9 3.260 828 .120 3.05 4.34 6.46 2.6 19 4 4.500 114.3 4.260 108.2 .120 3.05 5.62 8.37 1.6 19 5 5.563 141.3 5.295 134.5 .134 3.40 7.78 11.58 1.5 13 6 6.625 168.3 6.357 161.5 .134 3.40 9.30 13.65 1.0 10 8 8.625 219.1 8.249 2093 .188 4.78 16.96 25.26 2.1 7 "Calculated using Standard UL CRR formula, UL Fire Protection Directory, Category WZY The CRR Is ratio value used to measure the ability of a pipe to withstand corrosion. Threaded Schedule 40 steel pipe is used as the benchmark (value of 1.0). SCHEDULE 40 SPECIFICATIONS NOMINAL NOMINAL NPS NOM OD NOM ID WALL WEIGHT UI.. PIECES In. mm In. mm in. mm lbs/ft. kg/rn CRW Lift 1 1.315 33.4 1.049 26.6 .133 3.38 1.68 2.50 1.00 70 1¼ 1.660 42.2 1.380 35.1 .140 3.56 2.27 3.39 1.00 51 11/2 1.900 48.3 1.610 40.9 .145 3.68 2.72 4.05 1.00 44 2 2.375 60.3 2.067 52.5 .154 3.91 3.66 5.45 1.00 30 Calculated using Standard UL CRR formula, UL Fire Protection Directory, Category VIZY. "The CRR is ratio value used to measure the ability of a pipe to withstand corrosion. Threaded Schedule 40 steel pipe is used as the benchmark (value of 1.0). APPROVED FM Approved and Fully Listed Sprinkler Pipe Wheatlarid's Schedule 10 and Schedule 40 steel fire sprinkler pipe is FM Approved and UL, C-UL and FM Listed. Approvals and Specifications Both products meet or exceed the following standards: ASTM A135, Type E, Grade A (Schedule 10) ASTM A795, Type E, Grade A (Schedule 40) NFPA13 Manufacturing Protocols Schedule 10 and Schedule 40 are subjected to the toughest possible testing protocols to ensure the highest quality and long-lasting performance. Finishes and Coatings All Wheatland black steel fire sprinkler pipe up to 6 receives a proprietary mill coating to ensure a clean, corrosion-resistant surface that outperforms and outlasts standard lacquer ,ftcoatings. This coating allows the pipe to be easily painted, without special preparation. Schedule 10 and Schedule 40 can be ordered in black, or with hot-dip galvanizing, to meet FM/UL requirements for dry systems that meet the zinc coating specifications of ASTM A795 or A53. All Wheatland galvanized material is also UL Listed. Product Marking Each length of Wheatland fire sprinkler pipe is continuously stenciled to show the manufacturer, type of pipe, grade, size and length. Barcoding is acceptable as a supplementary identification method. PROJECT: CONTRACTOR: DATE: ENGINEER: SPECIFICATION REFERENCE: SYSTEM TYPE: LOCATIONS: COMMENTS: 00 BLACK LI HOT-DIP GALVANIZED II® Ei1X1 Tube .INC STEEL CROUP Fully Listed and FM Approved Sprinkler Pipe When you specify Schedule-10/Schedule-40 - M-COAT® sprinkler pipe from Allied Tube & Conduit, you get UL listed and FM approved products. Although these products do not require separate approvals, Schedule-10/Schedule-40 - M-COAT gives you the extra quality assurance you demand. Our Sch-10 (1-1/4" -8") pipe and Sch-40 (1" - 2-1/2") pipe have passed the same thorough lab testing as our other listed pipe products, and receive periodic mill inspections from both UL and FM agents to ensure consistent quality. ® Superior Coating Our advanced formula mill coating offers a clean, durable surface that is also paintready for custom color applications without special preparation. The internal surface of all black Fire Sprinkler pipe up to 4.5000" in diameter shall be coated with Allied Tube & Conduit Antibacterial Formula "M-COAT". American Made .Manufactured at one of 3 U.S. Facilities and is available through distributors in the USA, Canada, Mexico, and Latin America. Specifications & Approvals Schedule-10/Schedule-40 M-COAT pipe are in compliance with the following: ASTM Al 35, Type E, Grade A, and NFPA 13. Both pipe products have a working pressure rating of 300 psi maximum and also meet the stringent requirement for the following tests: Welded Outlets, Hydrostatic Pressure, Side Wall Rupture, Vibration Test. U . - vir NPS Nominal Nominal I.D. !Lt Specifications Nominal Wt. Wt. (1120 Filled)CR8 ln;mm aD. in; mm in- mm Wall in; mm ths!F6kq!m lbs/F6kqIm 1" 1.315 1.049 0.133 1.680 2.05 25 33.4 26.6 3.38 2.5 3.05 - 1114 1.660 1.380 0.140 2.270 2.93 T 32 42.1 35.1 3.56 3.39 4.36 - 1112' 1,900 1.610 0.145 2.720 3.61 1 40 48.3 40.9 3.68 4.0 5.37 - 2" 2.375 2.067 0.154 3.656 5.13 1 50 60.3 52.5 3.91 5.4 7.63 - 2W' 2.875 2.469 0.203 5.80 7.86 1 65 73 62.7 5.16 8.6 11.73 - I L1!'t U NPS Nominal Nominal ID. Nominal WI. WI. (1120 Filled) CRR O.D.In- mrn In; mm In; mm Wall Ir, nun 'bs!F6 kkr Lbs/F6 kqkn - 1/4" 1.660 1.442 0.109 1.810 2.525 7.0955 32 42,2 36.6 2.77 2,7 3.15 - 1½" 1.900 1.682 0.109 2.09 3.04 5.6570 40 483 42.7 2.77 3.1 4.52 - 2.375 2.157 0.109 2.640 4.22 4.5827 50 60.3 54.8 2.77 3.9 6.28 - 21/2" 2.875 2.635 0.120 3.530 5.89 3.5196 65 73 66.9 3.05 5.26 8,77 - 3.500 3.260 0.120 4.34 7.94 2.5550 75 88.9 82.8 3.05 6.4 11.82 4.500 4.260 0.120 5.62 11.78 1.6020 100 114.3 108.20 3.05 83 17.53 - 5"* 5.563 5.295 0.134 7.78 1733 1.4874 125 1 1413 134.5 3.40 11.58 25.80 - 6* 6.625 6.357 0.134 93 23.03 1.0251 150 168.3 1 161.5 3.40 13.8 34.27 - 8" 8.625 1 8.249 0.188 16.96 40.15 1.8365 200 219 209.50 4.78 25.2 59.75 - "Not available with M-Coat Co "C~~ APPROVED Project: Sprinkler Contractor: Date: Engineer: Specification Reference: System Type: Locations: Comments: cill - Customer Service: (800) 882-5543 Fax: (800) 659-7730 wwwaIIiedtube-sprinkIer.com ieci • 16100 S Lathrop Ave • 11350 Norcom Rd. • 2525 N 27th Ave. TUBE & CONDUIT Harvey, IL 60426 Philadelphia, PA 19154 Phoenix, AZ 85009 ©2013 Atkore International, Inc. All Rights Reserved. STP-S3-4M-1301 L Malleable Iron Threaded Fittings C Malleable Iron Threaded Fittings Class 150 and Class 300 Specifications <@> branded Class 150 fittings are UL Listed and FM Approved at 300 psi <@>branded Class 300 fittings are UL Listed Hot-dipped galvanized fittings are certified to; NSF/ANSI 614 and c UL us California AB1953 Lead Free LISTED Canadian Registration Numbers available at www.smithcooper.com FM Malleable castings conform to ASTM A197 < > APPROVED Hot-dipped galvanized fittings conform to ASTM A153 Malleable fitting dimensions conform to ASME B16.3 Malleable bushings, plugs and locknuts conform to ASME B16.14 Malleable unions conform to ASME B16.39 NPT threads on all fittings conform to ASME B 1.20.1 Independent lab verification that fittings meet applicable chemical & mechanical properties Manufacturing facilities are ISO 9001:2008 and ISO 14001 <& branded fittings are 100% air tested ProPakTM Packaging 9 C@US <~> Fig. 33E1&34E1 -90° Elbow LISTED APPROVED in I Size I Part Number A in Packing Weight lb Black Galvanized Inner Master 1/8 3/8 TTLI 3/4 1-1/4 :ii- 2 33E 10010 33E 1003C _j4C 34E 1001C 0.69 50 45 ]I 35 800 J 360 TT 140 80 40 16 -- 7 3 0.1 0.2 0.3 0.6 0.9 1.8 3.9 7.5 34E 1003C 0.95 C jj2 33E 1006C 34E 1006C 1.31 E1OiQC 33E 10120 iiJii 34E 1012C ETh4 341oi4 1.75 2.25 2.70 - -20 20 8 - - 33E 10200 34E 1020C iZTi33EiC 34E 10247- 3 33E 1030C 34E 10300 3.08 34E 1084 342 4 33E 1040C _____ 34E 10400 3.79 ---- 450 TTTE2 13.2 6 33E 10600 34E 10600 5.13 - 1 19.8 iDaC 638 Fig. 33RE1 & 34M1 - 90° Reducing Elbow Size Part Number A B Packing Weight in In in lb Black Galvanized Inner Master 1/4 x 1/8 33RE10020010 34RE10020010 0.76 0.74 40 j5 60 40 50 40 640 0.2 0.2 0.2 0.2 - 0.3 30001 4ftE1QQ0TC 0j5 Uf 480 - 400 320 160 o 3/8 x 1/4 33RE10030020 34RE1003002C 0.90 0.88 ::lN=8 jQO01C 34RT0O4I 8 096 112x 1/4 33RE10040020 34RE10040020 0.98 0.97 REJQ4003C 3E MOM T i 1.02 3/4x1/8 338E10060010 34RE1006001C 1.08 108 3/4x3/8 33RE10060030 34RE10060030 1.13 1.12 40 4p 160 160 0.3 or 7jj7 Eoac - 1 x1/4 338E10100020 34RE1010002C 1.22 1.10 25 300 0.3 ij fTL T i__0 3Q Tff: 34RE10100040 lx1/2 33RE10100040 1.36 1.26 25 100 0.4 - - -137 - pö 05 30iC WOI 33RE10120040 34RE10120040 1-1/4x1/2 1.53 1.34 20 80 0.6 3402Q0 j 33RE10120100 34RE10120100 1-1/4x1 1.67 1.58 10 40 0.8 = IX 3RE RE1014 1-1/2x3/4 1.75 1.52 10 40 0.8 33RE10140060 34RE1014006C jJli - 33_ffr1_014F107 S4REjQj4010Q1J6 10 40- o 1-1/2x 1-1/4 33RE10140120 34RE10140120 1.88 1.82 8 32 1.1 2j 1]' ØEIQQC - TO 40 1 2x3/4 33RE10200060 34RE1020006C 1.97 1.60 10 40 1.2 TxT E1020010 2O 28 1 2x 1-1/4 33R E10200120 34RE10200120 2.10 1.90 10 20 1.5 117 T4ã Z62 10 20 16 ETö 2J6 2-1/2x3/4 33RE10240060 34RE10240060 2.30 1.73 10 20 1.9 'flxT - 236 17 8 16 21 RET24 4RE4T 2-1/2x 1-1/4 33RE10240120 34RE10240120 2.44 2.03 8 16 2.2 1T2xV] 8 16 2 2-1/2 x 2 33RE10240200 34RE1024020C 2.60 2.39 8 16 2.6 3 x J2 33EtQ30OO4C 34BEii30006 -2,66- 1.6b 10 20 60 3x3/4 336E10300060 34RE10300060 2.60 1.87 8 16 6.6 x 1 floqi5c _ 2.4 3x 1-1/4 33RE10300120 34RE10300120 2.74 2.16 5 10 6.0 3 x 1_f/2 33REb1 C öJC 280 228 8 25 3x2 33RE10300200 34RE10300200 2.89 2.52 - 8 2.7 3 2 1/2 ffE4c 34Ej4C - 299 283 8 4,0 4 x 1-1/2 33RE10400140 34RE10400140 2.31 2.50 - 5 4.7 4x2 äETdoc 54 E0O2QC - 34T 274 5 51 4x2-1/2 33RE10400240 34RE10400240 3.50 3.05 - 5 6.3 4 ETo46300 4E1O4E a:60 - 5 6.6 175 SMITH-COOPER INTERNATIONALO 9 TOLL FREE 1-800-766-0076 • FAX (323) 8904456 • www.smithcooper.com Fig. 335E1 & 34SE1 - 90° Street Elbow C QLL) us<,-.> LISTED APPROVED Size I Part Number A B Packing Weight in In in lb I Black Galvanized Inner I Master 1/8 33SE1001C 34SE10010 0.69 1.00 60 960 0.05 I Ti2L. 1QC 081 i 3/8 33SE10030 34SE1003C 0.95 1.44 40 320 0.2 :-iii -: fC 34i9Q4t 112 3/4 33SE10060 33SE10120 514 34S61006C 34SE10120 34t 14C 1.30 - 1.75 1.89 2.44 70 4° 25 140 60 50 0.3 0.8 -.I__ 1-1/4 2 33SE1020C 34SE10200 2.25 3.27 8 16 2.0 JJ2 io - - 3 33SE10300 34SE1030C SEI 3.08 4.51 9 .. _ - : -j T 7 4.2 6 33SE1060C 34§E1060& 5.13 8.03 - 1 23.1 Flt. 330E1 & 340E1 - 90° Side Outlet Elbow Size in I Part Number A in Packing Weight lb I Black Galvanized Inner Master 1/8 330E1001C 340E1001C 0.69 45 720 ___ 0.1 ___ 1T4 - EiQQ2C :i _L_ 3/8 330E1003C 340E1 003C 0.95 50 20 15 11 T 0.7 200 WJT 0,2 80 30 12 0.2 0.4 1.1 2.5 i ijoc ooc 3/4 330E1006C 330E1012C 340E10060 1.31 1.75 2.25 1-1/4 340E10120 iQI1 340E10200 Ii2T 2 I3 330E10200 Fig. 33F 1 & 34F 1 - 45° Elbow Size in Part Number A in Packing Weight lb Black Galvanized Inner Master 1/8 33F 1001C 34F 10010 0.60 50 800 0.1 4FTC 3/8 33F 10030 34F 10030 0.80 50 400 0.1 FWQ 50 200 3/4 33F 10060 34F 10060 0.98 40 160 0.3 TotjaF 20 1-1/4 33F 10120 34F 10120 1.29 20 40 0.7 8 2 33F 10200 34F 10200 1.68 12 24 1.7 .F 1 4C 41` ¶S4 Tj 3 33F1030C 34F 10300 2.17 - 10 3.4 4 T3 F10öC 34FTh40c' r6T 3 64 5 33F 10500 34F 10500 3.05 - 2 12.1 6 Y3_r 10600 34F 10600 346 1 154 8 33F 10800 34F 10800 4.00 - 1 26.0 All male inreaus come wiin piasic proieciive caps Fig. 33SF1 & 34SF1 - 45° Street Elbow Size I in I Part Number A in B in Packing 1 Weight lb Black Galvanized Inner Master 1/8 33SF1001C 34SF10010 0.65 0.85 70 1120 0.1 i7 $Q2C 4SF1QC O7 094 40 640 5i 3/8 33SF10030 34SF10030 0.80 1.03 40 480 0.1 172 4'1 Ô2 3/4 33SF10060 34SF10060 0.98 1.29 40 160 0.3 I F1O10C 4SF1iOC 1T2 1.4,1 25 f66 05 1-1/4 33SF10120 34SF10120 1.29 1.71 10 40 0.8 1 172 3F1014C 341Ô1'0 1.43 1.88 10 40 0.9 2 33SF10200 34SF10200 1.68 2.22 12 24 1.5 1)2 33SF1024C 34SFi024C 1,95 257 5 10 27 3 33SF10300 34SF10300 2.17 3.00 - 6 3.6 4 33SF1040C 34SF1640C 2.61 3,70 - 4 9.2 176 SMITH-COOPER INTERNATIONAL® • TOLL FREE 1-800-766-0076 • FAX (323) 890-4456 • www.smithcooper.com Fiig33T1&34T1 -Tee c(,!9us > APPROVED LISTED Size In Part Number A in Packing Weight lb Black Galvanized Inner Master 1/8 3/8 W 3/4 _1:1/_4 __--T TT] 2 av 3 4 5 6 - - 33110010 331 10030 331 1006C T 34T 1001C 0.69 80 25 20 ET 640 200 --- 80 - __ 0.1 1 0.2 -- 0.5 - 1.2 2.5 6.1 9.7 - 26.4 - I-1 ffff1J 34T 1003C 0.95 fl2 1.31 34T 1006C TiiLii 33110120 T=_14T1014C 33110200 33T 10300 34T 10120 1.75 14 :TJL1 - - - - - 28 - 15 6 2 1 _1Ii- 34110200 2.25 34T 10300 3.08 11 42 33110400 341 1040C 3.79 33 ___475'U_ 33110600 34T 1060C 5.13 fl5 1 Fig. 33ST1 & 34ST1 - Service Tee Size in Part Number A in B in Packing Weight lb Black Galvanized Inner Master 1/2 33S110040 34S110040 1.12 1.63 40 160 0.3 - or 0- TT 1 i5O 05 1 33ST10100 34ST1010C 1.50 2.14 30 60 0.8 1114 3S'tiO12C 34STTT2C 05 245 15 30 1.2 1-1/2 33S110140 34S110140 1.94 2.69 10 20 1.7 2 3ST12C 4ST1020C 25 3.26 6 12 2.0 Fig. 3307'l & 340T1 - Side Outlet Tee Size in Part Number A in Packing Weight lb Black Galvanized Inner Master 1/2 330T10040 340T10040 1.12 20 80 0.2 3/4 33OT1006 34Oi9'ö5 15 60 04 1 330110100 34011010C 1.50 25 50 0.7 1-i/4 33011012C 340T10120 i.76 12 24 11 1-1/2 330T10140 340110140 1.94 8 16 1.4 2 83oTj020C 34011020C 2.25 - 10 2.7 Fig. 338T1 & 34BT1 - Bull Head Tee Size in Part Number A in B in C in Packing Weight lb Black Galvanized Inner Master 1/4x3/8 TJjT 33B11002003C 346T10020030 0,90 0.90 0.88 20 240 0.3 406Cj jj2' J 1/2x1 33BT10040100 34BT10040100 1.36 1.36 1.26 40 80 0.5 - WxT 3/4x1-1/4 JjJ4 jflp 1114151 :i iii 1.45 TT 1.65 . - 20 15 10 8 - - 40 30 24 20 - i 16 1 6 6 2 0.5 0.7 1.1 1.21 1.3 i 1.7 3 0 4.0 58 8.6 33B110060120 BT1112C 34BT10060120 1.62 1.62 - 1101 j 1 x 1-1/2 T 1-1/4x1-1/2 i-¶4'; 1-1/2x2 2x3 2112x3 3x4 338T1010014C 34BT10100140 1.80 1.80 ]J 33BT10120140 jIBflQ 34BT10120140 20C 1.88 TT5 2.16 1.88 - 2.16 - 202 1Y 1.82 2.02 239 2.55 23 3.30 33BT10140200 34BT10140200 II4 11 2 2.88 3c0 1 3.60 33BT10200300 BIjAOC 33BT10300400 34B110200300 34BI3aPO 34BT10300400 2.88 1 3.60 177 SMITH-COOPER INTERNATIONAL® • TOLL FREE 1-800-766-0076 • FAX (323) 890-4456 6 wwwsmithcooper.com Fig. 3311&34X1 -Cross C Q. L) us,~> LISTED APPROVED Size in Part Number A in Packing Weight lb Black Galvanized Inner Master 1/8 33X 1001C 33X 10030 34X1001C äic 34X 10030 34X 10060 34X 10120 34X 10200 a Xioi0 T5T6O 0.69 0.95 1.31 1.75 2.25 TTT 3.08 .. 20 40 20 - - - - 320 160 80 - 20 I 10 4 0.2 0.3 - 0.6 1.4 -f: 2.8 7.3 - :jA 3/8 Ti7E 1 00=4I 3/4 33X 1006C 1-1/4 33X 1012C 11I2 2 33X 10200 33X1O4i 3 33X 10300 34X 10300 4 -33XW A Size in Part Number A in Packing Weight lb Black Galvanized Inner Master 1/8 330 1001C 340 1001C 0.53 120 1920 0.05 1]4 330 -1 _002C -VC-10o2C - 60 40 i 25 15 12 - - - 2Q.40 720 00 320 i 100 60 24 12 10 5 005 0.1 3/8 330 1003C 340 1003C 0.74 TT 340 10060 -_aL75 0.97 TT 1.28 1.45 - I 1.80 2.08 232 2.55 - -, 0,1 0.2 0.5 1.1 2.2 3.9 6 8.8 3/4 330 1006C 1 33C Djy- 340 1012C 34010200 34010300 340 10400 340 1050C 34010600 c Thö 1-1/4 33010120 iiJ T4 2 33010200 - 330 1030C 330 10400 C 15f WCiQ24C 3 4 !i7 6 33010600 17-1 Fig. 33EP1 & 34EP1 - Extension Piece Size in Part Number A in Packing Weight lb Black Galvanized Inner Master 1/2 33EP10040 34EP10040 1.72 50 400 0.2 _3/4 - 4ET6C 1.b72 r 1 33EP10100 34EP1010C 2.20 30 120 0.3 fl71 EP112C 4EP11T 2.196 30 60 06 1-1/2 33EP10140 34EP10140 2.65 20 40 0.8 - -- - PIöC I 34EP10200 2.5 15 30 1.2 Fig. 33LT1 & 34LT1 - Lateral Size in Part Number A in B in Packing Weight lb Black Galvanized Inner I Master 1/2 33LT1004C 34LT10040 2.32 1.71 30 120 0.3 37 tii5öc 34L110060 277 205 40 80 06 1 33LT10100 34LT10100 3.28 2.43 20 40 0.9 1 Tf4 T01?C 34LT112C 394 292 12 24 14 1-1/2 33LT10140 34LT10140 4.38 3.28 10 20 2.0 2 .3LT1020C 34LT10200 517 393 5 10 31 2-1/2 33LT10240 34LT10240 6.25 4.73 - 4 8.2 33tT1030C 34LT 10300 7.26 5.55 2 16,1 4 33LT10400 34L110400 8.98 6.97 - 2 20.0 Fig. 33C 1 & 34C 1- Cap 178 SMITH-COOPER INTERNATIONAL® • TOLL FREE 1-800-766-0076 • FAX (323) 890-4456 • www.smithcooper.com Size in Part Number A in B in C in Packing Weight lb Black Galvanized inner Master 3/8x1/8 318 x 1(4 1/2x 1/8 33R11003001C 33RT 10030020 34RT1003001C 0.81 0.81 0.86 0.86 60 40 20 240 160 0.2 0.2 0.3 34RT10030020 0.81 0.81 0.91 33RT1004001C 34RT1004001C 0.91 0.97 480 1/2 X17 33RT10040020 34RT1004002C 0.97 0.97 0.98 20 160 0.2 - 1/2x 1/4 x1/2 1/2 x 3L8 33R11004002004C34RT1004002004C 1.12 0.97 1.12 20 . 160 0.2 33RT10040030 34RT1004003C 1.04 1.04 1.03 20 160 0.2 1/2x3/8x1/2 33HT1004003004C34RT1004003004C 1.12 1.03 1.12 20 160 0.2 3f4 x 1L4 33RT1006002C 34RT10060020 112 112 1,12 25 100 03 3/4x3/8 331RT1006003C 34RT10060030 1.12 1.12 1.13 25 100 0.4 33RT10060030060 34RT10060030060 1.31 113 131 25 100 OA 3/4x1/2 33RT1006004C 34RT10060040 1.20 1.20 1.22 20 80 0.4 33RT10060040040 34RT10060040040 120 112 1.22 25 100 0.3 3/4 x 1/2 x 3/4 33RT1006004006C 34RT10060040060 1.31 1.22 1.31 20 80 0.4 3/4x IL2xj i33RT1006OG4010C 34RT10060040100 145 1.36 137 18 72 05 1x1/4 33RT1010002C 34RT1010002C 1.12 1.12 1.25 20 80 0.5 1x3/8 33RT1010003C 34R110100030 1.18 118 1.27 15 60 0.5 1x1/2 33RT1010004C 34RT1010004C 1.26 1.26 1.36 15 60 0.6 - lx 1/2x 1J2 33RT101CO04004C 34RT10100040040 1.26 1.12 1.36 20 10 0.6 1x1/2x3/4 33RT1010004006c34RT1010004006C 1.37 1.22 1.45 20 80 0.6 1 x 1/2x1 33RT10100040100 34A110100040100 1.50 1.36 150 15 60 07 1x 3/4 33RT1010006C 34RT10100060 1,38 1.31 1.45 12 48 0.7 ) x 3/4 x 1/2 33RTiQ3004C 34RT10100060040 1.26 1.20 1.36 20 80 0.6 1x3/4x3/4 33RT1010006006C34RT1010006006C 1.38 1.31 1,45 15 60 0.6 1x3/4 x1 33RT1010096010C34RT10100060100 1.50 145 1,50 15 60 0,7 1-1/4x3/8 33RT1012003C 34R110120030 1.26 1.26 1.44 20 40 0.8 1 - 172 33RT10120040 34RT10040 134 1.34 153 20 40 08 1-1/4x1/2x1/2 33RT1012004004034R110120040040 1.36 1.12 1.53 25 50 0.6 11/4x 112x3/4 1-1/4 x 1/2x 1 1-1/4 x 1/2x 1-1/4 1-1/4x3/4 l-Ili x314x 1/2 1-1/4x3/4x 3/4 1-4x3f4x1 , 1-1/4x3/4x1-1/4 1-114x 1 1-1/4x1x1/2 1-1/4x 1 x3/4 1-1/4xlxl 1-iJ4ixi-i!4 1-1/2x3/8 1-1/2x 1/2 1-1/2x1/2x1/2 1-1/2x1/?x34 1-1/2x1/2x1 1-112x1j2x1.114 1-112x112x1-1/2 1-112x3/4 1-1/2x3/4x 1/2 1-1/2 x 3/4 x 3/4 1-1/2x3/4x1 1-112x3/4x1-1/4 1-1/2x3/4x1-1/2 1 1/2x 1 1-1/2x1x1/2 11/2x1x3/4 1-1/2x1x1 1-1/2x1x1-1/4 33RT10120040060 33RT1012004010C 3311012004012C 34RT1012004006C 34R110120040100 34R110120040120 1,45 1.58 175 1.26 1.36 1.53 -153 --25 1.67 1.75 20 20 20 10 10 10 10 20 23 2') 20 20 18 13 12 12 13 15 12 15 15 15 15 12 12 15 15 15 15 12 50 40 40 40 40 40 _ 40 40 40 40 , 40 40 36 36 48 48 36 30 24 30 30 30 30 24 24 30 30 30 30 24 -6.7- 0.8 1,1 0.9 07 0.9 1.1 1.0 0.8 1.0 0.9 t 1.0 1,0 0.7 -1. 1 1.0 1.1 1.1 1.0 1.1 1.1 1.0 1.1 1.3 12 0.8 12 1.1 1.2 33RT1012006C 34RT10120060 1.45 1.45 1.62 -1 .53 1.62 1.67 1.75 1,67 1.53 33R11012006004034RT1012006004C 53 06006C 33RT1012036010c34RT1012006010c 1.34 1.45 158 1.12 1.31 1 A 33R110120060120 33RT10120100 34R110120060120 34R110120100 1.75 1.62 1.58 1,58 33R110120100060 33RT1012010004034RT1012010004C 1.34 1.26 34R11012010006C 1.45 1.58 7500120 1 1,38 163 1.69 1.75 1.66 1.66 1.67 . 1.80 1.80 1.88 1.94 1.75 1.77 1,77 1.88 1.88 1.94 180 1.69 175 1.80 1 1.88 33RT1012010012034RT101201 33RT1012010010C34RT10120100100 1.50 1 33RT1014003C 33RT1014004C 33RT10140040060 33RT1014006C 33RT1014006006C 33R7 1014010C 33RT1014004004034R110140040040 338T1014004010034RT1014004010C 33RT1014004012034RT1014004012C 33RT1014004014C34RT1014004014C 33RT1014006004C34RT10140060040 33RT1014006010C34R110140060100 33R11014006012034RT1014006012C 33RT1014006014034RT10140060140 33RT1014010004034RT10140100040 33RT10140100634RT1014610006C 33RT1014010010034RT1014010010C 33RT1014010012C34RT1014010012C 34RT10140030 - 34RT1014004C 34RTi014004006C 34RT10140060 34RT10 140060060 34RT10140100 1.36 1.36 141 1.35 156 1.65 1.81 1.94 1.52 1.35 1.55 1.82 1.94 1.94 165 1.44 Tö 1.65 1.82 1.41 1.08 - 1.18 1.35 1.56 1.66 1.52 1.12 1.35 1.35 1.66 1.75 165 1.25 144 1.50 1.67 (9 C .L uS <> Fig. 33RT1 & 34RT1 - Reducing Tee LISTED APPROVED 179 SMITH-COOPER INTERNATIONAL® • TOLL FREE 1-800-766-0076 • FAX (323) 890-4456 • www.smithcooper.com Size in Part Number A in B in C in Packing Weight lb Black Galvanized Inner Master 1-1/2x1x1-1/2 33RT1014010014034RT10140100140 1.94 1.80 1.94 12 24 1.5 33 014O12C ii jig 13 __ 1-1/2x1-1/4x1/2 33RT1014012004C34RT1014012004C 1.41 1.34 1.66 12 24 0.9 iii i ii ...ii :'.r 1-1/2x1-1/4x1 33RT1014012010034RT10140120100 1.65 1.58 1.80 12 24 1.2 J2114 Qjc JTo 140 iwi :1 112 24 4 1-1/2 x 1-1/4 x 1-1/2 33RT1014012014C 34RT1014012014C 1.94 1.88 1.94 12 24 1.4 Jii4 L . i__M2 _L iiIi Iit1 2x3/8 33RT1020003C 34RT1020003C 1.49 1.49 1.88 10 40 1.6 Yx-ff 3R71020004Q 34flTf024C ji :i Lss i :20 _n: 2x 1/2x2 33RT1020004020C34RT1020004020C 2.25 1.88 2.25 8 16 2.0 7102O _LII 1 JJL J..Q... o 2x3/4x3/4 33RT10200060060 34RT1020006006C 1.65 1.31 1.92 12 24 1.5 2/4 .I06Q2 T1QQ0C 22S 16 2j 2 x 1 33R11020010C 34RT1020010C 1.73 1.73 2.02 10 20 1.7 102001Q010C, 34RT1O200100TOC :i ZE 111E 11I 11 F7 2x1x1-1/4 33RT1020010012C34RT1020010012C 1.90 1.75 2.10 10 20 1.6 2.xtjjJ2. 33R102o0b0014C 3001001 t881 1-0 20 1,5 2 x 1 x 2 33RT1020010020034RT10200100200 2.25 2.02 2.25 8 16 2.0 2ç1 RT1020G12 34RT1U20012C 190 190 ..L19. 8 16 7 2x1-1/4x1 33RT1020012010C34R11020012010C 1.78 1.65 2.10 10 20 1.5 iixi 33RTT020012Q 4T120012Th2C T j 2x1-1/4x1-1/2 33RT1020012014C34RT10200120140 2.00 1.88 2.18 8 16 1.9 x 1114 x 2 RT102001200C i10200 10 _2 ___ 735- 8 16 IT 2x1-1/2 33R110200140 34R11020014C 2.02 2.02 2.16 8 16 1.9 2i11j2x3/U Iii46 $4 Q200140 :f 110 2 - 2x1-1/2 x1 33RT1020014010034RT1020014010C 1.73 1.65 2.02 10 20 1.5 33RT102001401C 190 111L iP 1.8 - 2x1-1/2x1-1/2 33RT1020014014C34RT1020014014C 2.02 1.94 2.16 8 16 1.9 f_x 1-_1N 2-1/2x1/2 hi32 2-1/2x1 T11T17 2-1/2 x 1-1/2 RTT0142C 33RT1024004C 4T 142Q 34RT1024004C 1.65 21i[ 1.65 ]i 2.27 ii- - Eli J1EJ 16 2.4 ir 3.2 3.5 2.8 4.0 -3.7 3.9 2.4 2.4 2.7 4o 5.1 54 6.1 71 7.7 86 9.5 1 4 18.0 193 21.5 So, rtq: ir - - - - - - - - - - - - - - - ' - t.5-., Ew 16 10 10 - 10 10 6 6 6 6 4 4 4 4 3 3 3 1 1 1 1 i 33R11024010C 34RT1024010C 1.87 1.87 2.37 1o242 33R110240140 ]fl0?4pj 34RT1024014C 2LQ4 2.16 2.51 2.16 2WTT7jJ' 2-1/2 x1-1/2x2 jLTjj17 2-1/2x2 2 2-1/2 x 2 x 2-1/2 3x3/4 YxT -MET 3x1-1/4 A1 112 3 x 2 3x2x2 4 x 1/2 4xW 4X 1-1/4 4x11/ 4x2 4 x 1f2 4x3 6x 6x2-1/2 6x4 6x5 RT RT10240140 197 T 33RT1024014020C34RT1024014020C 2.39 2.16 2.60 Q i24Q.iQ 4c .4jj1.02401404 33R11024020C 34RT1024020C 2.39 2.39 2.60 R7110 33RT10240200240 i4OQC 34RT1024020024C IJh 2.70 2.60 1T 2.70 J4 33R110300060 34RT1030006C :i: 1.87 10 1.87 2.17 2.52 2.03 25 2.41 251 2.74 30 3.30 3.39 3%64 4.13 4.3 M 2.61 2.74 2.89 T 3.25 3.32 33 3.41 _151 3.60 56 4.66 4j5 4.94 5. 3QiC 33RT1030012C 103Q0j4' 33RT1030020C I 33R11040004C WqTC 33RT1040012C 1n1o4öö14 33RT1040020C 33RT10400300 Ri10b 33RT1060024C 33RT10600300 33R11060040C 334TiO60650 34RT1030012C T5IQ 34RT1030020C 34RT1040004C I56 34RT1040012C 34RTTOä14C 34RT1040020C 4ff[t04QQ?4P 34RT1040030C T1ä 34RT1060024C 34RTiO6003Q 34RT1060040C 34RTO65b 2.17 2.52 2.03 T 2.41 251 2.74 3b5 3,30 3 3.39 384 4.13 4.53 [1 . C®uS Fig. 33RT1 & 34RT1 -Reducing Tee, cont. LISTED AppRovED 180 SMITH-COOPER INTERNATIONAL® • TOLL FREE 1-800-766-0076 • FAX (323) 890-4456 0 www.smithcooper.com Fig. 33U 1 & 34U 1 - Union with Brass Seat 1(9",<e> APPROVED LISTED Size in Part Number A in Packing Weight lb I Black Galvanized Inner Master 1/8 14 3/8 3/4 33U 10010 34U 1001C 1.32 1.61 2.02 --1 4-4 24 30 20 40 TI - 20 10 - 480 160 ThO 80 6 40 20 - 7 0.1 0.3 0.5 1.3 3.3 - 6.8 33U 1003C j40 '15672 34U 1003C 12T133U36W 41J10 33U 1006C 34U 1006C i oc W ____ 1-1/4 33U 10120 34U 10120 2.26 2 7-- T-717 33U 1020C 34U 1020C 2.75 3 4 iT 33U 10300 jjoci 34U 1030C 3.54 tJ4OC 34U1040C3.85F Fig. 33FF1 & 34FF1 - floor Flange Size in Part Number A in B in C in Packing Weight lb Black Galvanized Inner I Master 1/4 33FF10020 34FF10020 2.83 2.00 0.31 50 200 0.1 1L 33FF0O3C 4ff1003C Z!E ii2 1T = = 1/2 33FF10040 34FF10040 3.00 2.10 0.36 50 200 120 0.3 14 1L_ _F1C 34FFJ1506U, 340 0.26 30 1 33FF10100 34FF10100 3.80 2.80 0.26 20 TW 12 J 6 -U1'6 80 i - 48 12 0.5 1.3 3.3 6.8 FT2 - - 420 w 1-1/2 33FF10140 34FF10140 4.60 3.45 0.30 T!fli52M -572-6- 6 4.00 0.30 5.00 T 7.00 0.37 1 0.45 2-1/2 33FF10240 34FF10240 6.75 x 4 33FF10400 34FF10400 9.50 Size Part Number A Packing Weight in in lb Black Galvanized Inner Master 1/8 33CP1001C 34CP1001C 0.96 70 1120 0.05 öT _____ 3/8 330P10030 340P10030 1.16 40 480 0.1 5j Tt TTo 3/4 330P1006C 34CP10060 1.52 50 200 0.3 TLT Too 1-1/4 330P10120 340P1012C 1.93 20 80 0.6 - TJT - 2 330F10200 340P10200 2.53 12 24 1.3 - CPT b24 2 - 3 330P10300 340P10300 3.18 8 16 2.8 Q?IjC - 8 35 4 330F10400 340P10400 3.69 - 6 4.6 JiC 05 341C 375 3 66 6 330P10600 340P10600 4.75 - 3 11.0 Fig. 33RL1 & 34RL1 - Right and Left Coupling Size in I Part Number A in Packing Weight lb I Black Galvanized Inner I Master 1/2 33RL10040 34RL10040 1.34 40 320 0.2 J4 34it1 12 5 2O 03 1 33RL10100 34RL10100 1.67 25 100 0.4 1 /4 4RE1C 1 T3 20 80 06 1-1/2 33RL10140 341900140 2.15 12 48 0.8 2 33RL1020C 34RL1020C 2.53 12 24 1.3 Fig. 33JP1 & 34P1 - Banded Coupling 181 SMITH-COOPER INTERNATIONAL® 9 TOLL FREE 1-800-766-0076 9 FAX(323)890-4456 • www.smithcooper.com Size in Part Number A in Packing Weight lb Black Galvanized Inner Master 1/4x1/8 33R010020010 34RC1002001C 34RC1003002C 34RC1004002C -1,13 1.00 1.13 IW I 1.25 11 1.44 - 1.44 - 1.69 50 30 50 .w 35 60 - - 45 600 360 400 280 240 180 0.1 0.1 0.1 0.2 - 0.2 T02 T 0.3 TY1 0.3 1i 3/8 x 1/4 33RC1003002C .iZL&iZL iQ1C 1/2x1/4 33RC1004002C _=2]L_ 3/4x1/8 oo4060 33R01006001C 34RC1006001C J/4x174 Q10060 3/4 x 3/8 33RC1006003C 34RC1006003C xl lx 1/4 33RC1010002C 34R010100020 I x 3L8 33CTOTOO 4T L69 - TJET 30 EIT1E 120 f00 1 x 1/2 33R01010004C 34RC10100040 1.69 ]±L4 33R1010OO6C RC10iC i Z9 25 25 1-.1/4x3/8 33R01012003C 34RC1012003C 2.06 100 0.5 T 174 x iI2 33RCIOI9QQi 4C10QQ4j T][T __iiT IJL_ 05 1-1/4 x3/4 33R010120060 34RC10120060 2.06 25 ____ 100 0.5 1114 x 1 33RC1012010C Z TTIE Io3 . 1-1/2x3/8 33RC1014003C 34RC1014003C 2.31 15 15 12 - 12 12 - - 12 J4 12 - - - - - - - - - - - - - - - - - - 34RC 101 Mn 3.69 22 60 60 48 48 48 24 25 - 25 25 20 20 18 10 10 10 10 iO 10 8 4 4 4 4 4 4 4 3 3 2 0.6 D117 13:F4_( 0.6 LT 0.7 - 0.9 T 0- - 1.0 - 1.0 1.5 1.7 JL. 1.8 2.2 TT 2.0 2.4 5 4.0 4o 3.7 4.4 4.4 4.0 4 5.5 55 5.2 7.5 7.5 7.9 99 8.7 17.1 1-1/2x3/4 33RC1014006C 34RC10140060 2.31 TL n2 x RC1O1 1-1/2x 1-1/4 33R010140120 34RC1014012C 2.31 2 x 32 33F4C1O2CO3C - 2 2.81 ]i 2x1/2 33RC1020004C 34RC10200040 RCt02O6C 2 33R01020010C 34R010200100 Jp2QQj 2.81 - 2.81 3.25 3.25 - 3.25 3.69 3.69 3.69 4.38 -8 4.38 4ä 4.38 4.38 4 3.87 387 3.87 46 4.20 4ö 4.20 4 20 4.20 5.25 RC1020012C' 2x1-1/2 33R010200140 34RC10200140 1240 21j2x112_C10.®c 2-1/2x 3/4 33RC1024006C 34R01024006C 2-1/2x 1-1/4 33RC1024012C 34RC1024012C z1JIIiZ I5 2-1/2x2 33RC1024020C 34RC1024020C 3x3/4 --~Fxj,~~f4j 33RC1030006C Tö 34RC1030006C xT 33RCJ030010C 4W3 34RC1030012C 34RC10300200 24 T34RC1030014 3x1-1/4 33RC1030012C 3.LUIL 3x2 33R01030020C 4x 1/2 34 - 4 x 1 -4 X_ T-1 JjQ - 33RC1040004C 33Bj 34RC10400040 ÔC 33R010400100 34RC10400100 34RC10400140 104002 34RC1040024C 3 1ö&3QC 34RC10500200 4Rcj05O24C 34RC1050030C 341050040C 34R010600200 34Tfö60b24C 34RC10600300 F10640C 34RC1060050C 34RC168O06OC 33RC1040014C 4x1-1/2 4x2-1/2 - 5x2 5 xJj12 5x3 6x2 ij] 6x3 - 6x5 8x6 IffC 33RC1040024C IA 33RC1050020C 33RT05Q24C 33RC1050030C iodo 33RC1060020C 24 TC 33R01060030C W1ö600öC 33RC10600500 J~4CicFgbbgdc S S S c®U Fig. 33RC1 & 34RC1 - Reducing Coupling LISTED APPROVED 182 SMITH-COOPER INTERNATIONAL® 9 TOLL FREE 1-800-766-0076 • FAX (323)890-4456 • www.smithcooper.com Fig. 33HB1 & 34HB1 - Hex Bushing C us ~> Q. L) APPROVED LISTED Size in Part Number A in B in Hex Packing Weight lb Black Galvanized Inner Master 1/4x 1/8 33HB10020010 3HB1002001C 0.61 .066 Out 120 1920 0.05 7(i1i TdooiC 3HT0OiC Oal o c5 i 1200 3/8 x 1/4 33HB1003002C 34HB1003002C 0.81 0.73 Out 75 0.05 T2 x TOO4OfC 33HB10040020 iO4p91C 34HB1004002C 0.95 IL 0.88 Out 100 800 0.1 1/2x 1/4 Jl8 043 3d _BIQW aC -r mr 320 0.2 3/4 x1/8 33HB10060010 34HB1006001C 0.95 LOJ 1.18 1W Out 40 Iz:iI2:- _ii 3/4 x3/8 33HB10060030 34HB10060030 1.05 1.18 Out 40 320 0.2 JS' 81O06 rot: - i 0.2 1x1/8 33HB1010001C 34HB1010001C 1.12 TT 1.16 iir 1.15 1.40 140 In Out -5t;r- 30 30 240 0.2 - =3H B dC 34HB10100030 21Q_ 240 0.2 1x3/8 33HB10100030 1 iJ r481o1otc 02 1x3/4 33HB1010006C 34HB1010006C 1.18 1.40 Out 30 240 0.2 1114 xjJ T!JQC ]J[ 1-15 In ....iQ 1-1/4 x3/8 33HB10120030 34HB10120030 1.20 1.15 In 30 120 0.4 1114 xj,L2 I8101P:2=0I4 1-1/4 x 3/4 33HB10120060 34HB1012006C 1.25 1,80 Out 30 120 0.3 12 0-3 1r4 x 1 _33H9i012 3Qi251 I2 T 1-1/2x1/8 33HB1014001C H13i102 34HB1014001C 1.30 1.18 In 25 100 0.4 JJIa&iL4 iioT4 3 In 05 jQQ OT 1-1/2x 3/8 33HB10140030 34HB1014003C 1.30 1.18 In 25 100 0.6 iDiZJ H114004C J5 j4 T Too _p 100 0.5 1-1/2x3/4 33HB10140060 34HB10140060 1.30 1.66 In 25 J12x1 flo9J i: T IT JE E J Q5_ 33HB10140120 BT 25 100 0.3 1-1/2x1-1/4 34HB1014012C 1,30 1i 1.95 Out x 114MH _2 JJ Ja_ 20 07 0.8 2x3/8 33HB1020003C 34HB1020003C 1.40 1.18 In 80 ___ 34T4B10200O4 T - b 0-9 2x3/4 34HB1020006C 1.50 1.68 In 20 80 0.9 33HB1020006C 2i 4i C'' Tb T!T V T TJ J5TO 2x1-1/4 33HB1020012C 34H81020012C 1.50 2.55 Out 20 80 0.7 Vx Th7 8TC fTJc i - 2 5ut - 20 2-1/2x 1/2 331-IB1024004C 34HB1024004C 1.70 3,25 Out 15 60 1.5 3Tö4öë TW T r i W 2-1/2x 1 33HB1024010C 34H81024010C 1.58 2.00 In 15 60 1.5 TT'31 jJc 34ffBi2 5 J J5 JI4_ 1.4 2-1/2x1-1/2 33HB'I024014C 34HB1024014C 1.58 2.70 In 12 48 ~1024 2 4HTc T F _T - 3x 1/2 3HB 31030004C 31 .88 4HB0300040 1 3.80 Out 6 24 2.0 4 34EBT 3 xl 33HB1030010C 34HB10300100 1.70 2.00 In 6 24 2.1 3UL4 1LQ3.QQl2C 34HBT12C 3 x 1-1/2 33HB1030014C 34HB1030014C 1.70 2.70 In 6 24 2.2 020 HBö 370 Out 6 24 YT- 33HB10300240 34HB1030024C 1.90 3.90 Out 6 24 1.6 3 x -1/2 3-i 2A rjo34p14C 34ftB134i4 T75 25 In 20 15 3-1/2x2 33HB1034020C 34HB1034020C 1.94 1.80 In - 20 2.4 3TJ2x2Tf2 T5ib24O 341B1O34C i.70 43Q Out TO 25 3-1/2x3 33HB1034030C 34HB1034030C 1.75 4.60 Out - 20 1.9 4 x O4O 341jB4ddö6C 2ö 2 fn 20 44 4x1 33HB1040010C 34H810400100 1.90 2.00 In - 20 4.5 4x11J4 ,Øi4 0012C 34H8fO4012C 10 240 In 20 27 4x 1-1/2 33HB1040014C 341-11310400140 1.90 2.70 In - 20 4.2 x2 T4I4OO20C 344B1O4ö'020C fO 30 In 4x2-1/2 33HB10400240 34HB1040024C 2.10 4.70 In - 20 3.9 4x3 HBT4C 34HB1400C '2 1'ö 470 out 20 3.3 4x3-1/2 33HB1040034C 34H810400340 2.33 4.75 Out - 20 2.5 5 x 2 33l-f1050020C 341-1131050020C 2,68 330 In 10 5.1 5x2-1/2 33HB10500240 34HB10500240 2.10 4.00 In - 10 4.8 5x3 33H810500300 34H81050030C 210 470 In 10 44 5x4 33HB1050040C 34HB1050040C 2.10 5.80 Out - 10 4.0 [I: S Bushings may have hexagon or octagon heads. 183 SMITH-COOPER INTERNATIONALA • TOLL FREE 1-800-766-0076 • FAX (323) 890-4456 0 www.smithcooper.com Fig. 33HB1 & 34H81 - Hex Bushing cont. CWL us<~> LISTED APPROVED Size in Part Number A in B in Hex Packing Weight lb I Black Galvanized Inner Master 6 x 1-1/2 33HB1060014C 34HB1060014C 2.20 3.35 In - 7 12.0 6 x 2 34R10C 7 6x2-1/2 33HB1060024C 34HB10600240 2.20 3.90 In - 7 7.9 6x3 4Hi06003OC in 7 77 R1060030 6x4 33HB1060040C 34HB10600400 2.30 5.90 In - 7 6.7 310QQoc:-3-4119 1 2 34HB1080060C 8x6 33HB1080060C 2.75 9.00 Out - 4 13.1 Bushings may have hexagon or octagon heads. Size in Part Number A in B in Packing Weight lb Black Galvanized Inner I Master 1/8 ____ 33SP1001C 34SP1001C 0.65 0.30 300 4800 2400L. 0.01 i0.03 iT _j4cQ _QzL_T I5.44 150 3/8 33SP1003C 34SP1003C 0.85 0.38 100 1600 0.05 sc 4Pioo4C 1,00 800 01 3/4 33SP1006C 34SP1006C 1.15 0.58 30 360 0.1 1-1/4 - tBLi 2 :7 3 4 Th 6 331i0C _13 71 2Q_ 40 Q 20 I4JJ Q27 0.3 33SP1012C 34SP1012C 1.40 0.90 160 JT TT I 1Q11 T TJQ M 33SP1020C 34SP1020C 1.60 1.30 80 32 16 10 0.7 j024 50 1.69 TJL 1 2.16 2.62 16 16 8 - Zf2 1.7 3.0 I 7.3 33SP1030C 34SP1030C 1.95 T11 2j - 2.30 2.80 33SP1040C 33SP10600 34SP1040C 34SP1060C Fig. 33BP1 & 34BP1 - Bar Plug Size in I Part Number A in Packing Weight lb I Black Galvanized Inner Master 4 33BP1040C 34BP1040C 2.30 8 16 3.5 5 - PiQ11 245 10 6.2 6 33BP1060C 34BP1060C 2.70 - 10 8.3 1080 C • .•- Fig. 33WN1 & 34WN1 - Waste Nut Size in Part Number A in B in Packing Weight lb Black I Galvanized Inner I Master 1/2 3/4 33WN10040 3Whi106C 34WN1004C 34WNI006C 2.00 2.50 3.15 3.87 25 20 200 1O 0.4 0.5 Fig. 33SP1 & 34SP1 - Square Head Plug Fig. 33LN1 & 34LN1 - Lock Nut* Size in Part Number A in B in Packing Weight lb Black Galvanized Inner Master 1/8 33LN1001C 34LN1001C 0.30 0.71 250 4000 0.03 1(4 EjTh02Q 3 .iC Q90 i2s 200 U3 3/8 33LN10030 34LN1003C 0.30 1.05 125 1500 0.04 1/2 33-LQ.Q4t 34L4C U7 100 öO 6.67 3/4 33LN1006C 34LN1006C 0.40 1.50 60 480 0.1 1 3SLJTQ10O tNThioc o 1 1-1/4 33LN10120 34LN10120 0.50 2.15 30 240 0.2 11/2 3T141ci14C 34LN161C 26 45 jO 0. 2 33LN10200 34LN1020C 0.57 3.10 25 100 0.5 2-1P 33rN1o24c LIj024O 0 2_ - 400 14 56 11 3 331_1\110306 34LN1030C 0.80 4.60 20 40 1.4 4 cf(T04C LF'T040 a9d 7 J4 2.9 NF-SL I breads 184 SMITH-COOPER INTERNATIONAL® • TOLL FREE 1-800-766-0076 • FAX (323) 890-4456 0 www.smithcooper.com Size in Part Number A in B in Packiflg Weight lb Black Galvanized Inner Master 1/4 33SE30020 34SE30020 0.94 1.44 140 280 0.1 1/2 1.25 33SE30040 34SE30040 2.00 60 120 0.3 32t 1 fJJ4 _31- 33SE3010C _ETC - ici 144 2 19AQ65 i 0.5 34SE3010C 1.63 2.56 30 60 0.9 f"Y89 1 36 i_S 1-1/2 2-1/2 33SE30140 34SE30140 34SE3024C ______ 2.13 3.13 12 24 2.0 2.94 -8' 33SE30240 4.50 - 12 -7- 5.4 All male threads come with plastic protective caps Fig. 33F3 & 34F3 - 450 Elbow Size in Part Number A in Packing Weight lb Black Galvanized Inner Master 1/4 33F30020 34F30020 0.81 120 240 0.1 W 3O 1/2 33F30040 34F30040 1.00 60 120 0.3 3T4 C C60 - 120 0.6 1 33F30100 34[ 34F30100 1.31 30 60 0.9 1114 - 1-1/2 33F30140 34F30140 1.69 12 24 2.0 2 34f1iC 6 2-1/2 3 33F 024C 34F 30240 2.25 4 8 5.0 3 3F3Oct 3F0 250 4 - 75 4 33F30400 34F30400 2.81 - 2 12.6 S US Fig. 33E3&34L3 -90°Elb 0 OW LISTED Size Part Number A Packing Weight in in lb Black Galvanized Inner Master 1/4 33E 3002C 34E 3002C 0.94 150 300 0.1 /8 127 1/2 33E30040 34E 3004C 1.25 60 120 0.4 3T4 o-u 1 33E3010C 34E 3010C 1.63 20 40 1.0 1114 J2t 34E326 1-4 28 4 1-1/2 33E 30140 34E 30140 2.13 12 24 2.2 EJt T. TTT 2-1/2 33E 30240 34E 30240 2.94 - 8 5.5 16.2 4 33E30400 34E30400 4.50 - 2 Fig. 33SE3 & 34SE3 - 900 Street Elbow Fig. 33T3&34T3 -Tee Size in Part Number A in Packing Weight lb Black Galvanized Inner Master 1/4 33T30020 34T30020 0.94 120 240 0.2 3/8 33L3QC 34T OC 1 ô T80 Q 1/2 33T 30040 34T 30040 1.25 60 120 0.6 J4 3T00 34 T4 4ö 09 1 33T30100 34T30100 1.63 20 40 1.4 11/4 20T 361-2t 341 3012C 194 12 24 23 1-1/2 33T30140 34130140 2.13 8 16 3.1 2 33T 30200 34TC 5O 5 10 48 2-1/2 33T30240 34T30240 2.94 3 6 7.6 3 33T 30300 34T 3030C 3.218 4 ft I3 4 33T 30400 34T 30400 4.50 - 2 1 22.6 185 SMITH-COOPER INTERNATIONAL® • TOLL FREE 1-800-766-0076 • FAX (323) 890-4456 • www.smithcooper.com A Size Part Number A Packing Weight in in lb Black Galvanized Inner Master 1/4 330 3002C 34C 3002C 0.78 Jä 240 180 480 310 0.1 3ZEI 03 1/2 33C 30040 34C 30040 JPc 0.98 60 4Q 120 80 0.2 03 :T c-W : 1 33C 30100 34C 30100 1.26 25 50 0.5 =-14 - Th12C 20 40 1-1/2 330 30140 34030140 1.43 20 40 1.1 2 _337C 360C 34C 30200 1.68 12 24 1.7 2-1/2 _336'3 0-2,4-0 340 30240 2.06 6 12 2,8 - 3113C 3030C 34C 3030C 217 6 12 42 4 -33&30'40C 340 30400 2.48 3 6 7.2 n Size in Part Number A in Packing Weight lb Black Galvanized Inner Master 1/4 33U 30020 34U 30020 1.55 100 200 0.3 3/8 - 33U004 340 30030 1.7i 60 120 04 1/2 33U 30040 340 30040 1.81 40 80 0.5 3/4 33U 3006C 340 30060 v2 20 40 08 1 33U 30100 34U 30100 2.31 25 50 1.1 1-1J 33LJä12C 34U 012C 266 15 30 19 1-1/2 33U 30140 34U 30140 2.85 12 24 2.5 2 330 j-0 340%200 323 6 12 36 2-1/2 33U 3024C 34U 30240 3.33 4 8 5.1 3 3(J3C 3T4Gö30C 409 4 8 78 4 33U 30400 34U 3040C 4.47 - 4 13.1 E 1] Fig. 33RT3 & 34RT3 -Reducing Tee c®us Size In Part Number A in B in Packing Weight I lb Black Galvanized Inner I Master 3/4 x 1/2 f1/ 33RT30060040 34RT30060040 1.31 1 4'2 1.50 1.63 1.63 1.81 T6 1.75 f1 2.00 2 ¶ 2.25 1.38 '1 50 1.56 169 1.75 181 1.81 1,88 200 06 2.06 3 2.25 2.38 25 3.13 - 4.25 20 Pb 20 12 12 8 8 5 5 5 - 5 -: - 2 40 40 40 24 16 16 16 10 10 10 4 - 4 0.8 11 1.2 m 1.8 Tb 2.1 2.5 3.1 3.6 4.2 300 33RT30100060 i30 00040 34RT30100060 1 x 3/4 1-1/4 x 3/4 33RT3012006C 34RT30120060 iTQ' 34R13014004C TVT 1-1/2x 1/2 33RT30140040 714 1-1/2x1 14 06 33RT30140100 04006 34RT30140100 T33! 2x1/2 i40iI 33RT3020004C ]4 34RT3020004C 2L$l4I_ 2x1 33RT3020010C 34RT30200100 J1 2x 1-1/2 33RT30200140 34RT30200140 3x2 ifl0Z4Q 33HT30300200 34RT30300200 W 2.81 : 4.00 6 7 9.1 9 - 10.3 4j2 4x3 424 33RT3040030C T30 34RT30400300 Fig. 33C3&34C3 -Cap g. 33U 3 & 34U 3 - Union with Brass Seat . 186 SMITH-COOPER INTERNATIONAL® 9 TOLL FREE 1-800-766-0076 • FAX (323) 890-4456 0 www.smithcooper.com Size I Part Number A Packing Weight in I in lb Black Galvanized Inner Master 3/8 x 1/4 33RC3003002C 34RC3003002C 1.44 100 200 0.2 ]3 --T.-6"§-' 20 1/2 x 3/8 33RC3004003C 34RC30040030 1.69 100 200 60 - 0.3 QQQLoo3C R 10Q3 L1 30 - 3/4 x 1/2 33R030060040 34R03006004C 1.75 45 50 90 i0Q 0.4 06 J_x 33F 1 x 3/4 2.00 50 100 0.7 33RC3010006C 34RC3010006C T47X 1 R ]3ii0 T 1-1/4x3/4 33RC3012006C 34RC3012006C 2.38 30 60 1.0 j14j. Qj 3J2T 28 T 60 1-1/2x 1/2 33RC3014004C 34RC3014004C 2.69 30 60 1.3 I31 - 1-1/2x1 33RC3014010C 34RC3014010C Ci0JC 2.69 2 20 - 40 1.4 iilriLV 2x 1/2 33RC3020004C 34RC3020004C 3.19 16 32 1.9 21' 06C 16 32 2.1 2 x 1 33RC3020010C 34RC3020010C 3.19 16 32 2.2 xT4 2Qj - 2 2x1-1/2 33RC30200140 34RC3020014C 3.19 12 24 2.5 JxTii 0[4C , 3 2-1/2 x 2 33RC3024020C 3.69 4 8 3.9 34RC3024020C 4RCO20C 4ö - 8 5.6 3 x 2-1/2 33R03030024C 34RC3030024C 4.06 - 8 5.9 "4x3 ä'c45ö06 - 6 9.2 c®uS V Fig. 3303 & 3403 - Banded Coupling LISTED Size I Part Number A Packing I Weight In I In lb Black Galvanized Inner I Master I 1/4 33CP30020 34CP3002C 137 200 400 0.1 - i. = -TOO 1/2 330P3004C 34CP3004C 1.87 60 120 0.3 co6 1 2.37 40 80 0.9 33CP3010C 340P3010C iig -L -T2_ Y4 1-1/2 33CP30140 340P3014C 2.87 12 24 1,9 ±i TTI T = 8 - i' 2-1/2 33CP30240 34CP3024C TL? 6,8 4.12 4 8 4.9 - a 330P3040C 4.69 4 34CP3040C - 4 11.3 Fig. 33RC3 & 34RC3 -Reducing Coupling Fig. 33UE3 & 34UE3 - Union Elbow with Brass Seat Size I in Part Number A in B in C in Packing Weight lb I Black Galvanized Inner Master 1/2 33UE3004C 34UE3004C 2.16 0.98 1.20 40 80 0.3 314 331JE30060 tJC 2' 1 T4 14d 3ö 60 09 1 33UE30100 34UE30100 2.81 1.34 1.77 20 40 1.3 11/4 J3012C 340E31C 323 161 215 10 20 20 1-1/2 33UE30140 34UE3014C 3.53 1.80 2.43 10 20 2.5 2 33U3O20C 34U EOOC 4jb 2.14 2.96 5 10 3.7 187 SMITH-COOPER INTERNATIONAL® • TOLL FREE 1-800-766-0076 • FAX (323) 890-4456 • www.smithcooper.com Order A H This And More ., Elf- - ko ,- a- Mechanical I Grooved &Fire * V / V V.. r V. r 4 I 1 . - . .3.• S . ...; V : I - .5.. V-V.. - '• - .•J-: I'D lot - d :. IL I You get it All. S Allin one place. It's not just a quality product - it's a quality system ap alityproducs are not enough. If you want every roduct to be a quality product, you need a quality ystem. Every product that is branded with the SO logois manufactured to precise standards, and inspected twice. All materials and dimensions are carefully monitored and meet relevant standards, and the whole process complies with ISO 9001 Standards. The SCI Trademark on each product is 100% traceable, because we're 100% responsible. SCI Quality Plus means our 50-year reputation for quality is built right in. -ii 'r'- 1T The benchmark of packaging & improved logistics Standardized carton sizes. Large wraparound labels. Packaging that's color coded by product line. And - outside of every box - a nice, clean picture of what's inside every box. SCI's Pro Pak System is a big idea that makes it possible for you to cut costs and improve service, simply by making it easier. From shipping and handling to tracking and reordering. And, at the same time, you'll be using your valuable warehouse space much more efficiently. The best guarantee you '11 never need The SCI 5/50 Guarantee says we will replace any pipe, valve or fitting for up to a fuU five years, when properly installed and operated, if failure is due to defects in material or workmanship. It's all about time. Ve understand that time is money which is why everything we do is designed to save you time. From our Quality Plus and Pro Pak systems to our 5/50 Guarantee, Smith-Cooper service adds value to each order you Place. Smith-Cooper will even pay $50 to the installing contractor to offset the cost of installation (please see the SCI Warranty at www.srnithcooper.com for details). We think that means we offer the highest quality pipe, valves and fittings available. Quality we stand behind for a full five years. Which makes it just that much easier for you to offer your customers the same high standards of quality and service. And that, in the end, is what we're all here for. 0 With locations on the East and West coasts, Smith-Cooper also offers speedy delivery. Each order is packaged to the exacting standards you have come to expect from us, no matter where it ships. Since we pay more attention to you, you have time to pay more attention to your customers. O 49 us 0OPLW' GROOVED. LISTED QUALITY Manufacturing facility is ISO 9001:2008 Quality inspections both at the overseas factory and our USA warehouses UL Listed & FM Approved - sizes up to 12" SERVICE Dedicated COOPLOKTM customer service staff Timely shipment of orders Faxed confirmation of every order Excellent fill rate ProPakTM System makes products easier to handle and warehouse TRACEABILITY The 41C> logo is on all fittings, couplings, bolts, and gaskets Canadian Registration Number (CRN) available at www.smithcooper.com (does not include fabricated fittings) AVAILABILITY Stocked in orange paint or hot dipped galvanized Stocked throughout the USA - sizes 1" to 24" PROTECTION I USA engineering staff available $7,000,000 product liability insurance SCI ProfthTm System I a 0,50 WWAPM asa Standard Weight Flexible Coupling with "C" Gasket Maximum working pressure depending on coupling size and schedule of pipe: ito 6' - 1000 psi (68.9 bar) 8 to 12"- 800 psi (55.1 bar) 14" to 20"- 300 psi (20.6 bar) 24" - 250 psi (17.2 bar) UL Listed & FM Approved - 1 thru 12' All housings, gaskets and bolts identified by SCI logo Gaskets are pre-lubricated Gasket Grade E - EPDM (green stripe) -30F (-34°C) to +230°F (+110°C) Gasket Grade I - Nitrile (orange stripe) -20°F (-29°C) to +180°F (+82°C) Gasket Grade 0 - Fluoroelastomer (blue stripe) +20°F (-6°C) to +300°F (+149°C) Ductile iron housings conform to ASIM A-536 Grade 65-45-12 Groove dimensions to AWWA C-606 Finishes: Orange enamel paint Hot dipped galvanized conforming to ASTM A-i 53 Smith-Cooper Warranty only applies to assemblies made with housings, gaskets and bolts carrying the @> logo i•ii "C" Style Gasket LISTED APPROVED A Pipe Part Number Max Pipe Dimensions Number Size Pipe OD End Gap Deflection Case Weight A B Painted Galvanized Degrees of QtY Sections in / mm i n / mm in / mm in / mm in i mm in / mm lb I kg 1 65SF3010 66SF3010 1.315 1/8 2.34 3.94 1. 73 2.3 2 40 1.3 25 33.7 3.2 59.5 100.0 44.0 0.6 1-1/4 65SF3012 66SF3012 1.660 1/8 2.70 4.41 1. 89 2.1 2 24 2.2 32 42.2 3.2 68.5 112.0 48.0 1.0 1-1/2 655F3014 66SF3014 1.900 1/8 2.93 4.69 1.89 1.9 2 24 2.3 40 48.3 3.2 74.5 119.0 48.0 1.0 2 65SF3020 66SF3020 2.375 1/8 3.48 5.20 1. 89 2.0 2 20 2.5 50 60.3 3.2 88.5 132,0 48.0 1.1 2-1/2 65SF3024 66SF3024 2.875 1/8 4.04 5.71 1. 89 2.3 2 16 3.0 65 73.0 3.2 102.5 145.0 48.0 1.4 3 65SF3030 66SF3030 3.500 1/8 4.63 6.50 1.89 2.0 2 16 3.3 80 88.9 3.2 117.5 165.0 48.0 1.5 3-1/2 65SF3034 66SF3034 4.000 1/8 5.24 7.48 1. 89 2.3 2 12 4.5 90 101.6 3.2 133.0 190.0 48.0 2.1 4 65SF3040 66SF3040 4.500 1/4 6.00 8.35 2. 13 2.2 2 8 6.1 100 114.3 6.4 152.4 212.0 54.0 2.8 5 65SF3050 66SF3050 5.563 1/4 7.07 10.04 2.13 1.8 2 6 8.5 125 141.3 6.4 179.5 255.0 54.0 3.9 6 65SF3060 66SF3060 6.625 1/4 8.31 11.42 2.15 1.6 2 4 10.6 150 168.3 6.4 211.0 290.0 54.5 4.8 8 65SF3080 66SF3080 8.625 1/4 10.35 13.62 2.48 1.4 2 - 16.4 200 219.1 6.4 263.0 346.0 63.0 7.5 10 65SF3100 66SF3100 10.750 1/4 12.87 16.61 2.64 1.2 2 - 25.3 250 273.0 6.4 327.0 422.0 6 7.0 11.5 12 65SF3120 66SF3120 12.750 1/4 14.88 18.66 2.64 1 .1 2 - 29.6 300 323.9 6.4 378,0 474.0 67.0 13.4 14 65SF3140 66SF3140 14.000 1/4 15.94 19.96 2.91 1.0 4 - 39.2 350 355.6 6.4 405.0 507.0 74,0 17.8 16 65SF3160 66SF3160 16.000 1/4 17.72 22.01 2.91 0.9 4 - 42.9 400 406.4 6.4 450.0 559.0 74.0 19.5 18 65SF31 80 66SF3180 18.000 1/4 20.08 24.53 3.15 0.8 4 - 54.0 450 457.6 6.4 510.0 623.0 80.0 24.5 20 65SF3200 66SF3200 20.000 1/4 22.09 26.57 3.15 0.7 4 - 57.3 500 508.0 6.4 561.0 675.0 80.0 26.0 24 65SF3240 66SF3240 24.000 1/4 26.10 30.59 3.15 0.6 6 - 76.9 600 _ 609.6 6.4 663.0 777.0 80.0 34.9 6 SMITH-COOPER INTERNATIONAL® 9 TOLL FREE 1-800-766-0076 • FAX (323) 890-4456 • www.smithcooper.com 1] Fig. 65SF1RI & 66SF1RI Standard Weight Flexible Coupling with Triple Seal Gasket Maximum working pressure depending on coupling size and schedule of pipe: 1" to 6-1000 psi (68.9 bar) 8 - 800 psi (55.1 bar) All housings, gaskets and bolts identified by SCI logo Gasket Grade E - EPDM (green stripe) -30F (-34CC) to +230F (+11 O'C) Other gasket materials available by special order O • Ductile iron housings conform to ASTM A-536 Grade 65-45-12 o • Groove dimensions to AWWA C-606 C L US • Finishes: Orange enamel paint LISTED Hot dipped galvanized conforming to ASTM A-i 53 Smith-Cooper Warranty only applies to assemblies made with housings, FM gaskets and bolts carrying the <@> logo APPROVED A Pipe Part Number Pipe OD Max Pipe Dimensions Deflection Number Case Weight Painted Galvanized A B Size End Gap Degrees of Sections in/mm in/mm in/mm in/mm in/mm in/mm lb/ kg 1-1/4 1.660 1/8 2.70 4.41 1.89 2.2 65SFTR13012 66SF1R13012 2.1 2 24 32 42.2 3.2 6&5 112.0 48.0 1.0 1-1/2 1.900 1/8 2.93 4.69 1.89 2.3 65SF1R13014 66SF1R13014 1.9 2 24 40 48.3 3.2 74.5 119.0 48.0 1 1.0 2 2.375 1/8 3.48 5.20 1.89 2.5 65SFTR13020 66SF1R13020 2.0 2 20 50 60.3 3.2 88.5 132.0 48.0 1.1 2-1/2 2.875 1/8 4.04 5.71 1.89 3.0 65SFTR13024 66SF1R13024 2.3 2 16 65 73.0 3.2 102,5 145.0 48.0 1.4 3 3.500 1/8 4.63 6.50 1.89 3.3 65SF1R13030 66SFTR13030 2.0 2 16 80 88.9 3.2 117.5 165.0 48.0 1.5 4 4.500 1/4 6.00 8.35 2.13 6.1 65SFTR13040 66SFTR13040 2.2 2 8 100 114.3 6.4 152.4 212.0 54.0 2.8 5 5.563 1/4 7.07 10.04 2.13 8.5 65SFTR13050 66SFTR13050 1.8 2 6 125 141.3 6.4 179.5 255.0 54.0 3.9 6 6.625 1/4 8.31 11.42 2.15 10.6 65SF1R13060 66SF1R13060 1.6 2 4 150 168.3 6.4 211.0 290.0 54.5 4.8 8 8.625 1/4 10.35 13.62 2.48 16.4 65SFTR13080 66SFTR13080 1.4 2 - 200 219.1 6.4 263.0 346.0 63.0 7.5 7 SMITH-COOPER INTERNATIONAL® • TOLL FREE 1-800-766-0076 • FAX (323) 890-4456 9 www.smithcooper.com fl a Fig. 65SR & 66SR Standard Weight Rigid Coupling with "C" Gasket Maximum working pressure depending on coupling size and schedule of pipe: 1 to 6° - 1000 psi (68.9 bar) 8 - 800 psi (55.1 bar) 10° & 12-600 psi (41.3 bar) 14° to 20° - 300 psi (20.6 bar) 24° -250 psi (17.2 bar) UL Listed & FM Approved - 1 thru 12° All housings, gaskets and bolts identified by SCI logo Gaskets are pre-lubricated Gasket Grade E - EPDM (green stripe) -30°F (-34°C) to +230°F (+110°C) Gasket Grade I - Nitrile (orange stripe) -20°F (-29°C) to +180°F (+82°C) B APPROVED • Gasket Grade 0 - Fluoroelastomer (blue stripe) +20°F (-6°C) to +300°F (+149°C) Ductile iron housings conform to ASIM A-536 Grade 65-45-12 Groove dimensions to AWWA C-606 Finishes: Orange enamel paint Hot dipped galvanized conforming to ASTM A-i 53 Smith-Cooper Warranty only applies to assemblies made with housings, gaskets and bolts carrying the <@> logo "C" Style Gasketl Pipe Part Number [ Pipe OD Max Pipe Dimensions Number Case Weight Galvanized A B C Size End Gap of Wy in/mm Painted in/mm in / mm in /mm in /ram in/mm Sections lb /kg 1 65SR3010 66SR3010 1.315 1/16 2.34 3.94 1.73 2 40 1.3 25 33.7 1.6 59.5 100.0 44.0 0.6 1-1/4 65SR3012 66SR3012 1.660 1/16 2.74 4.25 1.85 2 32 1.6 32 42.2 1.6 69.5 1 108.0 47.0 0.7 1-1/2 65SR3014 66SR3014 1.900 1/16 2.97 4.49 1.85 2 32 1.7 40 48.3 1.6 75.5 114.0 47.0 0.8 2 655R3020 66SR3020 2.375 1/16 3.48 4.88 1.89 2 24 2.2 50 60.3 1.6 88.5 124.0 48.0 1.0 2-1/2 65SR3024 66SR3024 2.875 1/16 4.00 4.79 1.89 2 16 2.8 65 73.0 1.6 101.5 1 147.0 48.0 1.3 3 65SR3030 66SR3030 3.500 1/16 4.59 6.38 1.89 2 16 3.2 80 88.9 1.6 116.5 162.0 48.0 1.4 4 65SR3040 66SR3040 4.500 1/8 5.87 7.72 2. 09 2 10 5.0 100 114.3 3.2 149.0 196.0 53.0 2.2 5 65SR3050 66SR3050 5.563 1/8 6.95 9.29 2.09 2 6 6.7 125 141.3 3.2 176.5 236.0 53.0 3.0 6 65SR3060 66SR3060 6.625 1/8 8.15 10.55 2.09 2 5 8.1 150 168.3 3.2 1 207.0 268.0 53.0 3.7 8 655R3080 66SR3080 8.625 1/8 10.24 13.23 2.56 2 - 14.3 200 219.1 3.2 260.0 336.0 65.0 6.5 10 65SR3100 66SR3100 10.750 1/8 12.71 15.82 2.56 2 - 20.7 250 273.0 3.2 323.0 402.0 65.0 9.4 12 65SR3120 66SR3120 12.750 1/8 14.92 18.03 2.56 2 - 25.4 300 323.9 3.2 379.0 458.0 65.0 11.5 14 65SR3140 66SR3140 14.000 1/8 16.02 19.45 2.87 3 - 33.5 350 355.6 3.2 1 407.0 494.0 73.0 15.2 16 65SR3160 66SR3160 16.000 1/8 18.03 21.50 2.87 - 36.9 400 406.4 3.2 458.0 546.0 73.0 16.7 18 65SR3180 66SR3180 18.000 1/8 20.16 23.46 2.99 - 9.4 450 457.6 3.2 512.0 596.0 76.0 17.9 20 65SR3200 66SR3200 20.000 1/8 22.13 26.06 3.07 - 53.9 500 _ ___ 508,0 3.2 562.0 662.0 78.0 24. 5 24 65SR3240 66SR3240 24.000 1/8 26.14 30.08 3.07 4 - 69.0 609.6 3.2 664.0 764.0 78.0 31.3 8 SMITH-COOPER INTERNATIONAL® • TOLL FREE -800-766-0076 • FAX (323) 890-4456 0 www.smithcooper.com Fig. 65SRTRI & 66SRTRI Standard Weight Rigid Coupling with Triple Seal Gasket Maximum working pressure depending on coupling size and schedule of pipe: 1 to 6° - 1000 psi (68.9 bar) 8 - 800 psi (55.1 bar) All housings, gaskets and bolts identified by SCI logo Gasket Grade E - EPDM (green stripe) -30°F (-34°C) to +230°F (+110°C) Other gasket materials available by special order Ductile iron housings conform to ASTM A-536 Grade 65-45-12 Groove dimensions to AWWA C-606 Finishes: Orange enamel paint Hot dipped galvanized conforming to ASTM A-i 53 Smith-Cooper Warranty only applies to assemblies made with housings, gaskets and bolts carrying the °©. logo LISTED APPROVED A A*k-,z Triple Seal Gasket - EPDM S Pipe Part Number Max Pipe Dimensions Size Pipe OD End Gap Number of Case Weight A B C Painted Galvanized Sections Wy in/mm In/mm in/ mm in/mm in/mm in/mm lb kg 1-1/4 655R1R13012 66SRTR13012 660 1...25 1/16 274 4 1. 85 2 32 1.6 32 42.2 1.6 69.5 108.0 47.0 0.7 1-1/2 65SR1R13014 66SRTR13014 1.900 1/16 2.97 4.49 1.85 2 32 1.7 40 48.3 1.6 75.5 114.0 47.0 0.8 2 65SR1R13020 66SRTRl3020 2.375 1/16 3.48 4.88 1.89 2 24 2.2 50 60.3 1.6 88.5 124.0 48.0 1.0 2-1/2 65SR1R13024 66SR1R13024 2.875 1116 4.00 4.79 1.89 2 16 2.8 65 73.0 1.6 101.5 147.0 48.0 _________ 1.3 3 65SRTRl3030 66SRTRl3030 3.500 1/16 4.59 6.38 1.89 2 16 3.2 80 88.9 1.6 116.5 162.0 48.0 ______ 1.5 4 65SRTRl3040 66SRTR13040 4.500 1/8 5.87 7.72 2.09 2 10 5.0 100 114.3 3.2 149.0 196.0 53.0 _____ 2.3 5 65SR1R13050 66SR1R13050 5.563 1/8 6.95 9.29 2.09 2 6 6.7 125 141.3 3.2 176.5 236.0 53.0 3.0 6 65SRTRl3060 66SRTR13060 6.625 1/8 8.15 10.55 2.09 2 5 8.1 150 168.3 3.2 207.0 268.0 53.0 3.7 8 65SRTRl3080 66SRTR13080 8.625 1/8 10.24 13.23 2.56 2 - 14.3 200 219.1 3.2 260.0 336.0 65.0 6.5 S 9 SMITH-COOPER INTERNATIONAL® • TOLL FREE 1-800-766-0076 • FAX (323) 890-4456 9 www.smithcooper.com C Fig. 65E & 66E 900 Elbow, Standard Radius C®US Ductile Iron - Full Flow LISTED UL/FM-1-1/4" to 12° only PPROVED G R 0 0 Pipe Size Part Number A Case Weight in/mm Painted Galvanized in/mm OtY lb / kg 1-1/4 65E3012 66E3012 2.75 50 1.0 32 69.9 0.4 1-1/2 65E 3014 66E 3014 2.75 36 1.2 40 69.9 0,5 2 50 65E 3020 66E 3020 3.25 82.6 20 2.1 0.9 2-1/2 65E 3024 66E 3024 3.75 12 2.7 65 95.3 1.2 65E 3030 66E 3030 4.25 15 3.8 80 1 108.0 1.7 4 65E 3040 66E 3040 5.00 8 7.6 100 127.0 3.4 65E 3050 66E 3050 5.50 - 10.6 125 139.7 4.8 6 65E3060 66E3060 6.50 150 165,1 7,1 8 65E 3080 66E 3080 7.75 - 28.7 200 196.9 13.0 10 65E 3100 66E 3100 9.00 50.7 250 229.0 - 23.0 12 65E 3120 66E 3120 10.00 - 70.1 300 254.0 31.8 14 65E3140 66E3140 14.00 - 106.9 350 356.0 48.5 16 65E 3160 66E 3160 16.00 - 158.7 400 406.0 72.0 18" through 24" sizes available upon request. S Pipe Size Part Number A Case Weight in / mm Painted Galvanized in / mm Oty lb / kg 1-1/4 65F 3012 66F 3012 1.75 65 0.7 32 44.5 0.3 1-1/2 65F3014 66F 3014 1.75 55 0.8 40 44.5 0.4 2 65F 3020 66F 3020 2.00 30 1.5 50 50.8 0.7 24/2 65F 3024 66F 3024 2.25 20 2.0 65 57.2 0.9 65F3030 66F3030 2.50 10 2.8 80 63.5 1.3 65F 3040 66F 3040 3.00 12 4.7 100 76.2 2.2 65F 3050 66F 3050 3.25 - 7.5 125 82.6 3.4 6 65F 3060 66F 3060 3.50 - 9.8 150 88.9 4.5 8 65F 3080 66F 3080 4.25 - 19.5 200 108.0 8.8 10 65F 3100 66F 3100 4.75 - 30.3 250 121.0 13,7 12 65F 3120 66F 3120 5.25 - 42.7 300 133.0 19.4 14 65F 3140 66F 3140 5.79 - 51.8 147.0 23.5 16 65F 3160 66F 3160 6.61 - 72.7 168.0 33.0 Fig. 65F & 66F 450 Elbow, Standard Radius Ductile Iron - Full Flow ULJFM-1-1/4"tol2°only c®us LISTED S 18" through 24° sizes available upon request. 18 SMITH-COOPER INTERNATIONAL® 9 TOLL FREE 1-800-766-0076 9 FAX (323) 890-4456 0 www.smithcooper.com Pipe Size Part Number A Case Weight in / mm in / mm OtY lb /-kg Painted Galvanized 1-1/4 65X3012 66X3012 2.75 20 1.8 32 69.9 0.8 1-1/2 65X3014 66X3014 2.75 16 2.0 40 69.9 0.9 2 50 65X 3020 66X 3020 3.25 82.6 20 3.3 1.5 2-1/2 65X 3024 66X 3024 3.75 io 4.9 55 95.3 2.2 65X 3030 66X 3030 4.25 7.3 80 108.0 3.3 65X 3040 66X 3040 5.00 10.0 100 127.0 4.5 65X 3050 66X 3050 5.50 - 15.3 125 139.7 6.9 6 65X 3060 66X 3060 6.50 24.6 150 165.1 - 11.1 8 65X 3080 66X 3080 7.75 - 41.6 200 196.9 1 18.9 Fig. 651&66X C®DS Cross, Standard Radius Ductile Iron - Full Flow LISTED UL/FM -1-1/4"t08"only APPROU S Fig. 65FA & 66FA Grooved x Flange Adapter C®US Ductile Iron LISTED UL/FM -2" to 8" only Matches Class 125/150 flange dimensions Fig. 65T & 66T .Tee, Standard Radius C®US Ductile Iron - Full Flow USTED ULJFM-1-1!4"to 12" only <2~> Pipe Size Part Number A Case Weight in 1mm Painted Galvanized in 1mm OtY lb I kg 1-1/4 65T3012 6613012 2.75 35 1.4 32 69.9 0.7 1-1/2 65T3014 6613014 2.75 24 1.7 40 69,9 0.8 2 50 6513020 6613020 3.25 82.6 15 3.1 1.4 2-1/2 6513024 6613024 3.75 7 4.1 65 95.3 1.9 80 6513030 6613030 4.25 108.0 10 5.8 2.6 6513040 6613040 5.00 110.0 - 100 127.0 4.5 65T 3050 6613050 5.50 - 15.0 125 139.7 6.8 6 65T 3060 6613060 6.50 - 22.3 150 165.1 10.1 8 65T 3080 66T 3080 7.75 - 41.1 200 196.9 18.6 10 65T 3100 6613100 9.00 - 64.8 250 229.0 29.4 12 65T 3120 66T 3120 10.00 - 90.9 300 254.0 41.2 14 65T 3140 6613140 11.00 - 116.8 350 279.0 53.0 16 6513160 66T 3160 12.00 145.0 400 305.0 - 65.9 18' through 24" sizes available upon request. 10" through 24" sizes available upon request. Pipe Size Part Number A Case Weight in 1mm in/mm Oty lb/kg Painted Galvanized 2 65FA3020 66FA3020 4.00 8 4.0 50 101.6 1.8 2-1/2 65FA3024 66FA3024 4.00 5.4 65 101.6 2.5 65FA3030 66FA3030 4.00 6.4 80 101.6 2.9 65FA3040 66FA3040 6.00 - 12.7 100 152.4 5.8 6 65FA3060 66FA3060 6.00 - 19.0 150 152.4 8.6 8 65FA3080 66FA3080 6.00 28.8 200 152.4 - 13.1 10 65FA3100F 66FA3100F 8.00 66.0 250 203.2 - 30.0 12 65FA3120F 66FA3120F 10.00 97.0 - 300 254.0 44.1 5'& 14" through 24" sizes available upon request. 20 SMITH-COOPER INTERNATIONAL® • TOLL FREE 1-800-766-0076 9 FAX (323) 890-4456 • www.smithcooper.com @TOLCO C® OS USTED Hardware Included UL Listed Design Load 1" (25mm) thru 2" (50mm) pipe size 655 lbs. (2.91kN) All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. 68 Fire Protection Solutions B-Line by [7.1Y-CJ Seismic Bracing Fig. 1000 - "Fast Clamp" Sway Brace Attachment D S Size Range: Pipe size to be braced: 1' (25mm) thru 4' (1 00mm) 40 1 PS. Pipe size used for bracing: 1' (25mm) and 11/4' (32mm) Schedule 40 (PS. For pipe sizes larger than 4" (100mm) please refer to TOLCO Fig. 1001. Material: Steel Function: A restraint device intended for lateral bracing. Features: Field adjustable, making critical pre-engineering of bracing pipe unnecessary. Unique design requires no threading of bracing pipe. Steel leaf spring insert provided to assure installer and inspector necessary minimum torque has been achieved. Installation: Fig. 1000 is the "braced pipe" attachment component of a lateral sway brace assembly. It is intended to be combined with the "bracing pipe" and TOLCO structural attachment component, Fig. 980, 910, 909 or other approved TOLCO component to form a complete bracing assembly. Follow NFPA 13 guidelines. To Install: Place the Fig. 1000 over the pipe to be braced, insert bracing pipe through opening leaving a minimum of 1' extension. Brace pipe can be installed on top or bottom of pipe to be braced. Tighten hex nuts until leaf spring is flat. It is recommended that the brace angle be adjusted before hex nuts are fully tightened. Approvals: Underwriters Laboratories Listed in the USA (UL) and Canada (cUL). Approved for use with Allied Dyna Flow sprinkler pipe up to 2" as a restraint device. Maximum horizontal design load is 655 lbs. (2.91kN) Torque requirement is 6-8 ft/lbs. (8-10Nm). For FM Approval information refer to page 69. Application Note: Position Fast Clamp and tighten two hex nuts until leaf spring flattens. A minimum of 1' pipe extension beyond the Fig. 1000 is recommended. Finish: Plain or Electro-Galvanized. Contact B-Line for alternative finishes and S materials. Order By: Order by figure number, pipe size to be braced, followed by pipe size used for bracing (1" I25mmI or 11/4' (32mm)) , and finish. Pipe Size in. (mm) Part Number & Approx. W000 V (24mm) Brace Pipe 11I4" (32mm) Brace Pipe Lbs. (kg) Lbs. (kg) Design Load Lbs. (kN) (25) 1000-1 X 71.6 (32.5) 1000-1 X 11I4 75.8 (34.4) 655 (2.91) 11/4" (32) 1000-11/4 X 74.8 (33.9) 1000-11I4 X 11/4 79.1 (35.9) 655 (2.91) 11/2" (40) 1000-11I2X1 71.8 (35.3) 1000-11kX11/4 82.1 (31.2) 655 (2.91) (50) 1000-2X1 84.1 (38.1) 1000-2X11I4 88.4 (40.1) 655 (2.91) 2112" (65) 100021/2 X 90.2 (40.9) 1000-21k X 11I4 94.6 (42.9) See FM (80) 1000-3X1 97.3 (44.1) 1000-3X1'14 101.7 (46.1) Approval 31/2" (90) 1000-31/1 X 104.0 (47.2) 100031/2 X 11/4 108.4 (49.2) Load Data (100) 1000-4X1 110.3 (50.0) 1 1000-4X11/4 114.6 (52.0) On Page 69 Eaton's B-Line Business seismic bracing components are designed to be compatible only with other B-Line bracing components, resulting in a listed seismic bracing assembly. B-Line's warranty for seismic bracing components will be the warranty provided in B-Line's standard terms and conditions of sale made available by B-Line, except that, in addition to the other exclusions from B-Line's warranty, Eaton's B-line Business makes no warranty relating to B-Line's seismic bracing components that are combined with products not provided by Eaton's B-Line Business. ®TOLCD C® us LISTED Set Bolt Included Mounting Hardware Is Not included All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. 66 Fire Protection Solutions B-Line by Seismic Bracing Fig. 980 - Universal Swivel Sway Brace Attachment - /8" to 3/4" Size Range: One size fits bracing pipe 1 (25mm) thru 2 (50mm), B-Line 12 gauge (2.6mm) channel, and all structural steel up to 1/4" (317mm) thick. Material: Steel Function: Multi-functional attachment to structure or braced pipe fitting. Features: This product's design incorporates a concentric attachment opening which is critical to the performance of structural seismic connections. NFPA 13 indicates clearly that fastener table load values are based only on concentric loading. Mounts to any surface angle. Break off bolt head assures verification of proper installation. Installation: Fig.980 is the structural or transitional attachment component of a longitudinal or lateral sway brace assembly. It is intended to be combined with the 'bracing pipe' and TOLCO 'braced pipe" attachment, Fig. 1000, 1001, 2002, 4L, 4A or approved attachment to pipe to form a complete bracing assembly. NFPA 13 guidelines should be followed. To Install: Place the Fig. 980 onto the 'bracing pipe. Tighten the set bolt until the head breaks off. Attachment can pivot for adjustment to proper brace angle. Approvals: —Underwriters Laboratories Listed in the USA (UL) and Canada (cUL). For FM Approval information refer to page 67. Note: Fig. 980 Swivel Attachment and Fig. 1001, 1000, 2002, 4A or approved attachment to pipe that make up a sway brace system of UL Listed attachments and bracing materials which satisfies the requirements of Underwriters Laboratories and the National Fire Protection Association (NFPA) Finish: Plain, Electro-Galvanized or Stainless Steel. Contact B-Line for alternative finishes. Order By: Figure number and finish. Pat. #6,273,372, Pat. #6,517,030, Pat. #6,953,174, Pat. #6,708,930, Pat. #7,191,987, Pat. #7,441,730, Pat. #7,669,806 Fig. 4L Part Mtg. Hdw. Mounting Hole Max. Design Approx. Number Size A B 0 Load (cULus) W000 in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) lbs. (kg) 98o-18 /8" (9.5) 5114' (1333) P/s" (47.6) 3/32" (10.3) 2015 (8.96) 149 (67.6) 980_l/2* 112" (12.7) 51/4" (133.3) 1/8" (47.6) 11/32" (13.5) 2015 (8.96) 148 (61.1) 980-/8 5/8' (15.9) 51/4' (133.3) 1f8" (47.6) 11/16" (17.5) 2015 (8.96) 147 (66.1) 980-/4 3/4" (19.0) 51/4" (133.3) 1/8" (47.6) 13/16" (20.5) 2015 (8.96) 146 (66.2) * Standard size Eaton's B-Line Business seismic bracing components are designed to be compatible only with other B-Line bracing components, resulting in a listed seismic bracing assembly. B-Line's warranty for seismic bracing components will be the warranty provided in B-Line's standard terms and conditions of sale made available by B-Line, except that, in addition to the other exclusions from B-Line's warranty, Eaton's B-line Business makes no warranty relating to B-Line's seismic bracing components that are combined with products not provided by Eaton's B-Line Business 0991. NId (ww LOZL X WW C'm x ww 9 u % jx % ji, x.y,91. :SU0!SUøW! ajii snuer jo jiewapeJ1 peosi6ei B SI ®swosicg snuer (eooi) pssiasei sq6p IIV,swelsAS °jld snuer eoo £I.O5-C-OC :pas!A soma JeMod icqpues o sinoq 06 01 dn ep!Aoid lip leql seiiaeq inoq-clwe 9 . ol dn esnoq II!M jeupeo eq 'UO!1!ppe UI wilellelsui esse 01 euqeo 941 jo doi pus peq epis 941 uo s1nopouj su124u00 joupeo eqj 6u!J WU4 4UflOW 4snil IsuoRdo us qim qsut pei e UI sewoo Ieued eqj -Nool AeM pus 'oop elqeAowej qi.M 4eulqeo lees eqeinp e ui pesnoq SI Ieued eqj U0i4eIIESU! AUS SlepOW -w000e ol 6uiwwei6oid w049n3 SMOIIB 19Usd eq 'SWeJ60Jd PJePuelS 941 01 UO!1!ppe U S91flU!W jo eew B U! welsAs GJUO 941 swei6oid sinpnilS nuej MOIIO4 ol eldw!s eq suoqse4su! jo 4JO!2W e SJ3AO3 qoiqm 'SWei6oJd piepuelS ZE seq ;e4 welsAs peseq-iosseooidoioiw 5 S3ZWfl 19usd oqj swe1sAs uoissajddns Jepju!Jds e6niep pus uope-aid se 1PM se swalsAs uoissejddns gig peseq 1u965 IfliM asn io pesq si 19usd 9111 SUO!15O!ldds Jo eqwnu 5 JOJ peIns II9M SI 12111 ieued 104 -uoo 6ulseelei Pieze4-916u!S 9Iqp(94 S S! 19USd IOi4UO3 6U!S29I9I IO-S=jr ®SW9ISAS aiij snuer eqj (zggot?g) soi.00a isnuew i.o-sr ui Lpiol i,as sjuewejinbai ol pWwil pus Aluo epow pmEl snuer Aiuo epow passe snuer, apow isQIweqo u poqe se eqewwei6oid euoz euo iciuo epow Ie3W9LP Ui ese 91OW9N alclewwe.i6oid. uo!pund pndg eqewwei6oJ. sapoj poqeeJqj. (epow paseq J91SM UI euoz Aiosiivadns I5U0fl!PPS olsilneJap) 1ilflJ!O poqy ssejo euo. sJewij. e6ie40s-ai eqeWLusJ60Jd. 6uIqsIn6uflx9 P9559 io ue6yioj eqen. P0iO Jr%OH iZ - 6ulwwej6oid flS J04 U0I3940Jd PJoMSSSd. icJoweAJ 19USd Ul SW2J6OJd piepus z - Aelds!O Ie4u9W9IddflS ai jepejeqo i - anpoj vldlno pus euoz Bu4eqiul vsssio I2u04dO. sAslej MOW91SM US 'Aiosi,uedns 'aqnoij. 'wiey. 1flOeWLj. 3!ISWOIflV qJM 4S9PII2M J8#nG kiosi.H 1U9A3 Ot. 9615q3510 p9wLL .10 Sfl0flUU03. uor WOJJ PP4Od s1!n 1!3 6uiseeje. sioiiuoo 6u1wwe.180Jd ueAua nuej p.lso u. 1XeJ. u0udu3s9a 9uqZ wosn3. ixei. uo.4dposea euoz pus e6sssej i9uue9 wo15n3. eIds!O an ouawn-eqdyJepsieq3 z - JosseooJdaloivj P9S!'U9dnS. 6u!uoz sSoi3 eqewwei6oJd. S1Ifl3J!3 1fld1flO 9 SS213 Jfl01. S1lfl3J!3 Aiosuuedng 9 SSS3 0Mj. 911fl3J13 6Uq2I1JUJ 9 SS23 JflOI. uoileiedO PJBZSH-316U!S. sejn;eej 13NVd 1011NOJ 9NISV313J DSI 005 Revised: 30-Dec-2013 JFS-CI Layout PALINPIJrS5NITIATING ZONES) CONNECT TONORMALLYOPEN DEVICES ORCOME4TIBLES WIRE SMOKE DETECTORS. MAXIMUM LINE RESISTANCE: 100 OHM (EXCEPT WITH LINEAR HEAT DETECTION) 1 5jK 51K 51K 5.1K 5,1K 5,1K EOLR EOLR EOLR EOLR EOLR EOLR I2OVAO6O& 165 VA MAX. 22GVAC/G01h 185 VA MAX. fl CUGIECIOR L_NONPOWIIR.._J UI.GIESAND 66000 @Goo 00006 019191s ,~F' 24V& C 0 ' ] PROGRAM SWITCH EACH CASZ WILL CONVENT2 CLASS B ZONES INTO 2 CLASSA ZONES OPTIONALcLASSA CONNECTIONS EOLRIS NOTUSIID PORCLASSA PANEL OUTPUTS (INDICATING RELEASING CIRCUITS) NON-POWER A. LIMITESAND OUIPUT oulpuT ouwur oulpuT RATr _l _z+ _3+ -+ + - ISIS RIG II ;WO RUG 5.1K 5.1K EOL EOL SOLE EOLR DIODE DIODE IZVBATU. I2VBATT. AIGY ASSY RELAY CONTACTS DRY CONTACTS RATED AT 3A, 30VDC RESISLI 1 SIUSIS,r+1 Notes: Connect only UL Listed 24 VDC devices to indi- cating circuits. Connect EOL Diode assembly IN SERIES with solenoid on release circuit. Leave EOLR (provided) on all unused circuits. Polarity mark on output terminal is for a normal, no alarm condition. Polarity reverses when output is activated. Maximum current per output is 1 Amp. Maximum voltage is 33 VDC. Maximum current for all four outputs combined is 2-1/2 Amps. All outputs are special application 24 VDC. All initiating and NAC/Retease circuits are super- vised and power limited. All frequencies are continu- ous. Maximum resistance on outputs is 10 ohms. Maxi- mum resistance on outputs programmed as releas- ing, is I divided by current requirements of solenoid. Notification outputs do not provide synchroniza- tion. If synchronization is needed, refer to the Janus Fire Systems® JFS-C1 manual. Synchronization is only on one circuit and not between circuits. The maximum cannot exceed I amp or whatever the maximum that the sync module can support, which- ever is lower. Page 2 of 4 DSIOOS Revised: 30-Dec-2013 Architects/Engineers Specifications The control panel for the extinguishing agent releasing system shall be a microprocessor based control capable of protecting multiple hazards in one control panel. It shall be Underwriters Labora- tories Inc. listed under Standard 864 Ninth Edition and Underwriters Laboratories of Canada listed for Local Control Units for Releasing Service. The control shall also be approved by Factory Mutual Research Corporation and be compliant with the requirements of NFPA-72 (Local: A, M, SS service types; DAC and NC signaling type) and NFPA-12, NFPA-12A, NFPA-13, NFPA-15, NFPA-16, NFPA-17, NFPA-17A, NFPA-750, and NFPA- 2001. The control shall be housed in an 18 gauge steel cabinet that has a hinged, removable door with a key lock. The finish shall be baked enamel and available in red with contrasting trim and logo. An optional matching bezel should be available for semi-flush mounting. The cabinet shall have ade- quate space to house 18 AH standby batteries capable of operating the system for up to 90 hours. The control shall include a fully supervised integral power supply/battery charger capable of provid- ing 200 mA to the auxiliary power circuit It shall also be capable of providing 2.5 Amps to all releas- ing and notification appliance circuits combined. All initiating, output, and auxiliary power circuits shall be power limited. The control shall have a 32 character (16 characters, 2 lines) backlit LCD display and a 34 LED supplemental display. All diagnostic and alarm event information shall be viewable in text form on this display. A field programmable custom banner message with the current date and time shall be displayed when no current alarm or diagnostic information exists. All operational features of the control panel shall be field programmable using menu driven selec- tions on the alpha-numeric display and on board controls. No special programmer will be required and jumpers or switches to configure operational features shall not be permitted. Alarm and trouble indications shall resound when required. The control panel shall be equipped with 32 programs built into the panel memory, 14 for water based extinguishing and 18 for agent extinguishing. In addition, the panel shall have the ability to add custom programs. All programming functions shall be password protected. The control shall have four fully supervised Class B (Style B) initiating circuits capable of supporting the operation of 25 compatible 2-wire smoke detectors on each circuit. The individual circuits shall be selectable through the programming sequence to operate in one of the following modes: Conventional, Waterfiow, Linear Heat Detection (up to 10,000 feet per zone), Manual Release, Low Air Alarm, Supervisory, Tamper, Low Air or High Air. Optional Class A modules, CA2Z, may be added for Class A operation. The panel shall have a Low Air Zone that creates a supervisory condition and map to an output. The control shall have two fully supervised Class B (Style B) supervisory circuits. These circuits shall be selectable through the programming sequence to operate in one of the following modes: Supervisory, Tamper, Low Air or High Air. The control shall have one fully supervised Class B (Style B) abort circuit with 3 different operating modes, ULI, IRl, and NYC. The control shall have four fully supervised Class B (Style Y) output circuits. These circuits shall be selectable through the programming sequence to operate as one of the following: Alarm Notifica- tion Appliance, Supervisory Notification Appliance, Trouble Notification Appliance or Releasing. The optional CAM module may be added to convert the outputs to Class A. The panel shall have an RS-485 output and auxiliary power outputs for connection and supervision of up to 4 remote annunciators. The releasing circuits shall be supervised for short circuit conditions and shall be programmable for cross zoning operation when required. The panel shall have programmable spurt function and remote reset available in Janus Based modes. Refer to JFS-CI Manual DOC1 05 (5403552) for requirements for use of remote reset. Page 3 of 4 OSIQOS Revised: 30-Dec-2013 The discharge timer for these releasing circuits shall be programmable for times of 0.1 minutes to 30.0 minutes in 0.1 minute increments or 1 minute to 300 minutes in 1 minute increments. All initiat- ing and output circuits shall be capable of being individually disabled or enabled. In addition, when in the agent extinguishing mode there shall be a pre-discharge timer adjustable from 0-60 seconds from an alarm zone or 0-30 seconds from a manual release zone. The control shall have a test mode that will automatically disable all releasing circuits. The test mode shall operate in such a manner as to automatically reset the initiating circuit and indicating cir- cuits after detecting each alarm condition initiated by the test. All testing shall be recorded in the 40 event history buffer. The test mode will automatically terminate after twenty minutes of inactivity. The control shall have four integral relay contacts rated 3 Amps at 30 VDC for connection to exter- nal auxiliary equipment. One relay shall operate when an alarm condition occurs, another when a trouble signal occurs, the third when a supervisory condition occurs, and the fourth during a water- flow condition. JFS-CI Single Hazard Releasing Control Panel (Red Cabinet) 18630 PFC-TR Béze! for Semi.-Flush Mounting (Red). 18709 BT-80 Battery, 12V 8AH (2 Req'd) 18641 BT-120 Battery, 12V I2AH (2 Req'd) 18642 BT-180 Battery, 12V, I8AH (2 Req'd) 18643 CA2Z . 2 Zone Class .A Initiating Circuit Module 18631 CAM Class A Indicating Circuit Module 18632 ARM-2 Auxiliary Relay Module . 18633 ARM-44 Relay Module 19091 RA-4410RC Remote Annunciator 18634 PS-24 Photoelectric Smoke Detector 18635 SB.46 Smoke Detector Base 18637 n!a Spare CPU . . . . 18640 nla EOL Resistor/Diode Assembly for Releasing Circuit 18712 Will EOL Resistor, 5.1K 99950 Note: Approvals/Listings maintained by and manufactured by Potter Electric Signal Company. The seller makes no warranties, express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose, except as expressly stated in the seller's sales contract or sales acknowledgment form. Every attempt is made to keep our product information up-to-date and accurate. All specific applications cannot be covered, nor can all requirements be anticipated. Al specifications are subject to change without notice. 1102 Rupcich Drive Millennium Park Crown Point, IN 46307 TEL: (219) 663-1600 FAX: (219) 663-4562 e-mail: info©janusfiresystems.com www.janusfiresystems.com Page 4 of 4 BATTERY CALCULATIONS iFS-Cl AZARD: GIA IT CLOSET - PREACTION SUPERVISORY ALARM DULE QTY. mA SUB-TOTAL mA SUB-TOTAL iFS-C1 (18630) 1 121 121.00 274 274.00 PHOTOELECTRIC SMOKE DETECTOR (18635) 1 0.045 0.05 150 150.00 CONVENTIONAL DETECTOR BASE (18637) 1 1 0 0.00 46 46.00 ALARM BELL 24VDC (MB-G6-24-R) 1 0 0.00 30 30.00 HORN (MT-12/24) 2 0 0.00 108 216.00 ELECTRIC SOLENOID 1 0 0.00 41 41.00 AMP: 0.12 AMP: 0.76 HOURS I SUB-TOTALS I TOTAL STANDBY 24 0.12 = 2.91 A.H. ALARM 0.08 0.76 = 0.06 A.H. Total A.H. Rating = (Standby + Alarm) * 1.2 3.56 TOTAL A.H. - NOTE: N miscalculation assumes that one hazard is discharging 1I _jrIE This calculation assumes that all alarms are functioning F I K E S Y S T E Ivt S This calculation assumes that all inputs are in alarm. 0 IHc)C1MlKI america corporation SLR-24V PHOTOELECTRIC SMOKE DETECTOR Shown without base. STANDARD FEATURES Low profile, 1.8" high (with base) 2 or 4 wire base compatibility, relay bases available Highly stable operation, RF/Transient protection Low standby current, 45jiA at 24VDC Two built-in power/sensitivity supervision/alarm LEDs Non-directional smoke chamber Vandal resistant security locking feature Built-in magnetic go/no go detector test feature Removable smoke labyrinth for cleaning or replacement Automatic Sensitivity window verification function meets outlined requirements in NFPA72, Chapter 2 & 7, Inspection, Testing and Maintenance Compatible with SIJ-24 ionization detectors Backwards compatible with Hochiki SLK and SIH detectors SPECIFICATIONS Light Source GaAlAs Infrared Emitting Diode Rated Voltage 17.7- 30.0 VDC Working Voltage 15.0- 33.0 VDC Maximum Voltage 42 VDC Supervisory Current 451iA @ 24 VDC Surge Current 160iA max. @ 24VDC Alarm Current 150mA max. @24 VDC Air Velocity Range 0-4000 fpm Ambient Temperature 32°F to 120°F (0°C to 49°C) Color & Case Material Bone PC/ABS Blend Sensitivity Test Feature Automatic Sensitivity window verification test Mounting Refer to NS Conventional Detector Base Data Sheet APPLICATION The SLR-24V can be used in all areas where Photoelec- tric Smoke Detectors are required. The wide range smoke chamber makes the SLR-24V well suited for fires ranging from smoldering to flaming fires. NS-4 Series, NS-6 Series, HSC-4R or HSC-xxx R Style bases may be used with the SLR-24V. Current interchangeable/compatible devices are the SIJ-24 ionization detector, the SLR-24H photoelectric detector with heat sensor, and the DCD-1 35/190 heat detectors. All NS conventional devices are mechanically compatible with Hochiki America HSB, HSC and YBA type bases which may have been used in previous installations. Please check individual panel listings for compatible bases. OPERATION The SLR-24V photoelectric smoke detector utilizes two bicolored LEDs for indication of status. In a normal standby condition the LEDs flash Green every 3 sec- onds. When the detector senses that its sensitivity has drifted outside the UL listed sensitivity window the LEDs will flash Red every 3 seconds. When the detector senses smoke and goes into alarm the status LEDs will latch on Red. The detector utilizes an infrared LED light source and silicon photo diode receiving element in the smoke cham- ber. In a normal standby condition, the receiving ele- ment receives no light from the pulsing LED light source. In the event of a fire, smoke enters the detector smoke chamber and light is reflected from the smoke particles to the receiving element. The light received is converted into an electronic signal. Signals are processed and compared to a reference level, and when two consecutive signals exceeding the refer- ence level are received within a specified period of time, the time delay circuit triggers the SCR switch to activate the alarm signal. The status LEDs light continuously during the alarm period. ( PRODUCT LISTINGS I SIGNALING I LISTED APPROVED 1D5AIAY California State Fire 1. : Marshal 7272-0410:107 I S1383 Specifications subject to change without notice. Continued on back. Hochiki America Corporation Find latest revision at www.hochiki.com 7051 Village Drive, Suite 100 Buena Park, CA 90621-2268 L I Phone: 714/522-2246 Fax: 714/522-2268 /9001:2000\ Technical Support 800/845-6692 ortechnicaIsupport@hochiki.com ________ AssembledintheUsA / RE01&1ERD \ '0017 1012010 INIT CI] UL 12VDC0 Hochiki Ameilca Corporation SLR-24V UL LISTED CONTROL PANEL LQ P ER HSC-RELAY SERIES LISTED END OF LINE DEVICE TERMINAL BLOCK USED ON HSC- RA/RST VERSION ONLY HSC-IXXX)R .RE) toe 6 H jLj 5 NIO 4 ro 3 c 2 2 AND 4WIRE BASE RELAYS SHOWN WITH 'WER OFF. LISTED END OFLINE DEVICE HSC-4R CONTACTS [ OH I2 EL oPUR~~J LISTED END OF LINE RELAY HA-EOLR.I2 OR HA-EOLR-24 Specifications subject to change without notice. HSC-4R HSC-4R ENGINEERING SPECIFICATIONS The contractor shall furnish and install where indicated on the plans, Hochiki America Model SLR-24V photoelectric smoke detectors. ,# e combination detector head and twist-lock base shall be UL listed compatible with a UL listed fire alarm panel. base shall permit direct interchange with Hochiki America SLR-24H combination photoelectric/heat detector, SIJ-24 ionization smoke detector and/or DCD-1 35/190 fixed temperature/rate-of-rise heat detectors. The base shall be appropriate twist-lock base NS-4 Series, NS-6 Series, HSC-4R, or HSC-xxx R. In the event of partial or complete retrofit, the SLR-24V maybe used in conjunction with, or as a replacement for, Hochiki America detectors (SLK-24, SLK-24FH and the SIH-24) on most HSB and HSC base applica- tions. The smoke detector shall have two flashing status LEDs for visual supervision. When the detector is in standby condition the LEDs will flash Green. When the detector is outside the UL listed sensitivity window the LEDs will flash Red. When the detector is actuated, the flashing LEDs will latch on Red. The detector may be reset by actuating the control panel reset switch. The sensitivity of the detector shall be capable of being measured. It shall be possible to perform a functional test of the detector without the need of generating smoke. The sensitivity of the detector shall be monitored automatically and continuously to verify that it is operating within the listed sensitivity range. To facilitate installation, the detector shall be non-polarized. Voltage and RF transient suppression techniques shall be employed to minimize false alarm potential. Auxiliary SPDT relays shall be installed where indicated. SLR-24V SENSITIVITY TEST FEATURE The SLR-24V Photoelectric Smoke Detector has a built-in automatic sensitivity test feature. In normal condition, both LED's flash green. When the sensitivity drifts outside of its sensitivity limits, both LED's flash red. In the alarm state both LED's are red continuously. When the sensitivity drifts outside of its sensitivity limits and both LED's flash red, the device needs to be cleaned or returned to the factory for cleaning. Refer to HATechnical Bulletin HA-97 for cleaning information. 2-WIRE OPERATION ULLISTED I CONTROL PANEL t-) PANEL POWER SUPPLY line SERIES NS6 SERIES Annunciation device must be current limited to 20 mA 24VDC Maximum. Not limiting current could result in damage to the detector or cause a no alarm condition. 2-WIRE RELAY OPERATION, LISTED END OF LINE DEVICE NOTE: - WIRING TERMINALS FOR THE NS4 AND NS6 ARE IDENTICAL - BASES WITH THE "W SUFFIX ARE WHITE IN COLOR 0 0 ld- WEPCOYO Conventional Initiating Rate- of- rise/Fixed Temperature Heat Detectors M, ,, 280B-PL Series C Overview 280B-PL Series heat detectors offer fixed temperature or combi- nation rate-of-rise and fixed temperature detection. RATE-OF-RISE: A temperature increase at the sensor of 15°F (9°C) or more per minute activates the rate-of-rise feature. This closes the contacts in the sensor to transmit the alarm condition to the fire alarm control panel. When the rate-of-rise element alone has been activated, the sensor is self-restoring. FIXED TEMPERATURE: If the temperature of the center disk rises to the sensor's rated temperature, the fixed temperature element activates. This closes contacts in the sensor and trans- mits an alarm condition to the fire alarm control panel. The fixed temperature element is non-restorable and, when activated, the detector must be replaced. The need for replacement is indicated when the center disk has fallen free from the detector. Standard Features UL listed for 50 ft. (1 5.2m) spacing Single pole - normally open contact Low profile with mounting plate Pure white finish Mounting flexibility with screw terminals Easy twist-on installation On-site testing of rate-of-rise feature Positive operating indication - for fixed temperature element Application Heat detectors are most suitable for environments where rapid fire development can be expected. When selecting the location on the ceiling for the heat sensor, do not locate it in direct path of hot or cold air flow. Refer to the detector specifications for the recom- mended maximum spacing. Earlier detector response may be obtained by reducing the spacing between detectors. Installation Edwards 280B series heat sensors come standard with a white plastic reversible mounting plate. The plate is designed for surface or flush mounting and installs directly to a standard North Ameri- can 31/2 or 4 inch octagon box. Once the mounting plate is fixed, a simple twist will lock the sensor in place. It can be removed using a screwdriver to release the tamper-resistant locking finger. This helps prevent unauthorized removal. Pagel 012 ., r A sir F. 7 S85001-0261 N ,, '' U'p, Issue 4 Catatoo Number 2818-FL 2828-PL 2838-FL 284B-PL UL Temperature Rating 135°F (57°C) 194°F (90°C) 135°F (57°C) 194°F (90°C) UL Max Ambient Temp. at 100°F (38°C) J Ceiling 150°F (66°C) 100°F (38°C) I 150°F (66°C) Fixed Temperature and Rate-of- Detector Type Rise Rate-of-rise: Fixed Temperature Only 15° F (9° C), self restoring UL Recommended Cover- e 2,500 ft.2 (232 m2) UL Recommended Spacing 50 ft. (15.2 m) FM Recommended Spacing 30 ft. (9.14 m)_ UL Maximum Distance from 25 ft. (7.6m) from any wall or projection extending down from the Wall ceiling more than 12 inches (305 mm) Contacts - Rating Single Pole Normally Open 3.0 amps at 6 to 125 Vac; 1.0 amp at 6 to 24 Vdc; 0.3 amps at 125 Vdc; 0.1 amps at 250 Vdc Operating Environment Indoor - Dry Agency Listings UL, FM, CSFM Maximum aetector coverage nsa been determined by UL to provide detection time equal to spnnrier devices spaced at 10 ft (3.05m) intervals on a smooth ceiling 15 feet 9 inches (4.8rn) high, Higher ceilings may adversely affect detection time. Earlier detection may be obtained by reducing the spacing between sensors. (See NFPA 72, Chapter 5) J Contact us... Phone: 1-800-336-4206 Web: www.edwardssignaling.com Edwards Signaling is an EDWARDS brand. 3 Farm Glen Boulevard Farmington, CT 06032 In Canada, contact Chubb Edwards... Email: inquiries@chubbedwards.com Web: www.chubbedwards.com © 2013 UTC Fire & Security Americas Corporation, Inc. All rights reserved. Specifications subject to change without notice. Edwards is part of UTC Climate, Controls & Security, a unit of United Technologies Corporation. fl WARNING - Use For Property Protection Only Heat sen- sors do not protect life against fire and smoke. In most fires, hazardous levels of smoke, heat and toxic gases can build up before a heat detector would initiate an alarm. independent studies indicate that heat detectors should only be used when property protection atone is involved. in cases where life safety is factor, the use of smoke detectors is recommended. Under no circumstances should heat detectors be relied upon as the sole measure to ensure fire safely. However, if they are spaced in accordance with the directions in the Specifica- tions table, these sensors can contribute, within an overall Sm safety program, to reducing the risk of avoidable property losses. Mounting The plastic mounting plate is molded to accommodate exposed wiring. LOOKING FINGERS SANVECE FLASH SURFAUR MOUNTiNG .., I' I i, MOUNTING f'7'MOUNTHe DIED I I I I SiDU / / MOLES 141 a .-.l I— -.-____...—'kFLUSH MOUND 21155 BREAK MOEY2 Secrioss (52,rn0 FROST VIEW ON CIRCUMTERENCS PANIC RAN,NEie MNeeiN PlAN Cie r1U UTOAfL Specifications Ordering Information Cat. No. Description 10 IlISENU. DETECTOR - MATCH ARROWS ON DETECTOR MAID MOUNTING PLATE. PUSH UP AND 'TURN ELUCTRICAL BOX CLOCITWISE. lIMO supllliedl ET>1aON) 10 REMOVE DETECTOR - FIIAN. Is UFT LOCIUNG FINGER WITH Wising DRIVER TIP AND Canduft TURN DETECTOR COUNTER- CLOOTWADE FAWINT VIEW MAN U45Ag FAIIC PIN OX-NFL bAN. ..pANMy1 Ship Wt. lb (kg) 281 B-PL Heat Detector, 135°F (571C), Rate-of-Rise and Fixed Temperature 282B-PL Heat Detector, 194°FL 0°C Rate-of-Rise and Fixed Temperature 1.0 '05 28313-PL Heat Detector, 135°F (571C), Fixed Temperature 284B-PL Heat Detector, 194°F (90°C), Fixed Temperature Detector Accessories 280A-PL Plastic Mounting Plate - White, Reversible (included) Page 2 of 2 S85001 -0261 Issue 4 Fe S Series CVXICSX Explosion-Proof Bells & Series MB Motor Bells Effective: June 2007 mpmu\js&[~ Protection Systems A UTC Fire & Security Company F-75-003 SERIES CVXICSX EXPLOSION-PROOF BELLS FEATURES Approvals include: UL, CSA Rugged cast mechanism enclosure with hinged cover Available in single stroke and vibrating models High sound output Standard red enamel finish Outdoor models Include protective guard Indoor Model cvx10/csx10 Outdoor Model CVXG10ICSXG 10 UL LISTED FOR HAZARDOUS ATMOSPHERES Class Group Contents of Hazardous Atmosphere B Hydrogen or gases and vapors of equivalent hazards, such as manufactured gas C Ethyl and ether vapors D Gasoline, petroleum, naphtha, alcohol, acetone, benzene, lacquer solvent, vapors, natural gas II F Carbon black, coal, coke dust II G Flour, starch, grain dusts ORDERING INFORMATION Model Number Part Number Where Used Shell Size [Input Voltage dBA @ loft. Current (Amps) Mounting Options Vibrating CVXI0-115-R 75-000040-001 Indoor 10 inch 115 Vac 90 .220 Note I CVXGI0-115-R 75-000040-002 Outdoor 10 inch 115 Vac 90 .220 L Note I Single Stroke CSXIO-115-R 75-000040-003 Indoor 10 Inch 115 Vac 67 .125 Note I CSXGIO-115-R 75-000040-004 Outdoor 10 inch 115 Vac 87 .125 Note I CVXIO-24-R 75-000040-005 Indoor 10 inch 24 Vdc 87 .500 Note I CSXGIO-24-R 1 75-000040-006 Outdoor 10 inch 24 Vdc 87 .500 Note 1 Note: All models include an integral cast backbox for surface mounting with 112 in. threaded conduit entrances on top and bottom of the housing. S SERIES MB MOTOR BELLS FEATURES Approvals include: UL, FM, CSFM, MEA 64nch and 104nch shell sizes, 24 Vdc models Mounting options for surface, semi-flush, outdoors and concealed conduit installation Screw terminals permit fast in-out field wiring of 12 to 18 AWG wire Red textured finish to Improve appearance and durability DESCRIPTION Fenwal Series MB Motor Bells provide a superior engi- neered motor bell for fire and life safety alarm systems. The Series MB offers higher CIBA, low current draw; built- in trimplate for semi-flush mounting, low frequency alumi- num shells for better audibility, low RFI noise and high torque. A permanent magnet motor is incorporated for durable, reliable performance. ORDERING INFORMATION I Model I Input I dBA @ I Current Number Part Number j oitegeISheU Size lOft 41 j1B-G6..24-R 5-0000300D1 LOO003OO2 I 24 6 inch I 92 I .030 24 G12R 10 inch 92 .030 MOUNTING OPTIONS Model Number Part Number Mounting Options SFP-R 75-000000-005 F BB-R 75-000000-006 C AP-R 75-000000-007 G WBB-R 75-000000-008 E Fenwal is registered trademark of Kidde-Fenwal Inc. SEMI-FLUSH CadS a C. SURFACE 00 BC CONCEALED CONDUIT AP E. OUTDOOR a,. Note: Refer to Data Sheet 75-008.A for mounting hard- ware dimensions. .This literature is provided for informational purposes only. KIDDE-FENWAL, INC. i mv[E ruiraL assumes no responsibility for the product's suitability fore particular application. The prod- I uct must be properly applied to work correctly. I Protection Systems If you need more information on this product, or if you have a particular problem or ques- I A UTC Fire & Security Company don, contact KIDDE-FENWAL, INC., Ashland, MA 01721. Telephone: (808) 881-2000. 400 Main Street Ashland, MA 01721 F-75-003 Rev AS © 2007 Kidde-Fenwal Inc. Printed in USA Ph: 508.881.2000 Fax: 508.881.8920 www.fenwalfire.com Effective: June 2007 Series IT Multitone Horns and F~~ LI a Series MT Multitone HornDStrobes ' Protection Systems A UTC Fire & Security Company F-75-001 FEATURES Approvals include: UL 1911 and UL 464. Factory Mutual (FM), California State Fire Marshal (CSFM) and New York City (MEA). Designed to meet or exceed ADA!NFPAAJFCIANSI Standards and Accessibility Guidelines. Meets OSHA 29 Part 1910, 165. One alarm appliance with eight (8) selective signals to provide superior sound penetration for various ambient and wail conditions with two field selectable sound output levels. Audible and strobe can operate from a single signal- ing circuit with any of the eight (8) audible signals. Code-3 Horn and Tone meet ANSIINFPA temporal pat- tern for standard emergency evacuation signaling. Multi-Candela MT Strobe models available with field selectable 151301751110 candela settings. Single Candela MT Strobe models available with 151 15 candela rating. Weatherproof MT Strobe models available with 751 180 candela rating. Strobe markings far fire and suppression applica- tions. Wide listed voltage range, filtered (DC) and FWR. Polarized Inputs for compatibility with standard reverse polarity type supervision of circuit wiring by an alarm panel. Low cost installation via standard electrical boxes. Attractive flush or surface mounting options. No additional trimplate required for flush mounting. IN and OUT wiring terminations that accept two (2) 912 to #18 AWG wires at each terminal. DESCRIPTION Fenwal Series MT and MT Strobe Multitone electronic signals offer a choice of eight (8) nationally and interna- tionally recognized alerting sounds: Horn, Bell, March Time Horn, Code-3 Tone, Code-3 Horn, Slow Whoop, Siren or Hi/Lo Tone. Our Code-3 horn and tone patterns are engineered to comply with NFPA/ANSI Temporal Pat- tern specifications without requiring additional equip- ment. With MT and MT Strobe Signals, one alarm appliance meets most of your signaling needs. The MT Strobes are designed for ADA applications with maximum performance, reliability and cost-effectiveness while meeting or exceeding the latest requirements of NFPA 72 (1999), ANSI 117. 1, UFC (2000) and UL Stan- dard 1971 as well as meeting ADA requirements con- 0 cerning photosensitive epilepsy. Series MT Horn Strobe (with lOB backbox) Series MT Horn Each MT and MT Strobe appliance has two user selec- tive sound output levels: STANDARD dBA and HIGH dBA. The MT-1 2/14 provides dual voltage capability in one unit, 12 Vdc or 24 Vdc operation, filtered or FWR. The MT Strobe Electronic Signals operate with 24 Vdc and may be used with filtered or unfiltered (full-wave-rectified) input voltages. Separate input terminals are available and shunt wires are provided to enable both tone and strobe to operate simultaneously from a single input The Multitone Strobe Signals are UL Listed for indoor wall mount applications, under Standard 1971 for Devices for the Hearing Impaired and under Standard 464 for Audible Signal Appliances. MT Strobe models are listed for indoor use with a temperature range of 32°F to 120F (0°C to 49°C) and maximum humidity of 93% ± 2%. The MT-12/24 and MTWP models for outdoor use are Listed for -31°F to 150°F (-35°C to 66°C) and maxi- mum humidity of 95%. The strobe devices use a Xenon flashtube with solid state circuitry enclosed in a rugged Lexan° (or equivalent) lens to provide maximum reliability for effective visible signaling. Strobe lens markings avail- able for Fire" and Agent" labeled applications. The Series MT Signals have IN and OUT wiring termina- tions that accept two #12 to #18 AWG wires at each ter- minal. Inputs are polarized for compatibility with standard reverse polarity type supervision. S Table 1. Alarm Tones Tone Nami Tones Pattern Description Horn Broadband Horn (Continuous) Bell 1560 Hz Modulated (0.07 sec. ON/Repeat) March lime Horn Horn (0.25 sec. ON/0.25 sec. OFF/Repeat) Code-3 Horn Horn (ANSI S3.41 Temporal Pattern) Code-3 Tone 500 Hz (ANSI 83.41 Temporal Pattern) SlowWhoop 500-1200 Hz SWEEP (4.0 sec. ONi0.5 sec. OFF/Repeat) Siren 600-1200 HZ SWEEP (1.0 sec. ON!Repeat) HI/Lo 1000/800 (0.25 Sec. ON/Alternate) GENERAL NOTES Strobes are designed to flash at I flash per second minimum over their Regulated Voltage Range." Note that NFPA-72 (1999) specifies a flash rate of I to 2 flashes per second and ADA Guidelines specifies a flash rate of I to 3 flashes per second. All candela ratings represent minimum effective Mul- titon Strobe intensity based on UL 1971. The MT Audible is UL 464 Listed. Regulated Voltage Range" is the newest terminology used by UL to identify the voltage range. Prior to this change, UL used the terminology "Listed Voltage Range." Table 3. Current Ratings for Series MT Strobe Portion Model RMS Current (Amps) MT'241575 MVJVP2475 Pil'24MCW Candela 1575cd 180cd 15cd 30cd 75cd 110cd 24.0 Vdc 0.060 0.094 0.041 0.063 0.109 0.140 UL Ma 0.090 0.138 0.060 0.092 0.165 0220 * RMS currant ratings are per UL average RMS method. UL max current rating is the maximum RMS current within the listed voltage range (16-33v for 24v units). For strobes the UL max current Is usually at the minimum listed voltage (16v for 24v unite). For audlbles the max current is usually at the maximum listed voltage (33v for 24v unite). For unfiltered FWR ratings, see Installation Instructions. S SPECIFICATIONS Table 2. dBA and Current Ratings for Series MT Audible Portion Tone RMS Current (Amps) dA@ 10 Ft (UL Reverberant) d8A@ 10 Ft 24 VDC 12 VDC 24 VDC 12 VDC l2 and 24VDC HI Output - STD Output HI Output - - STO Output - HI Output $10 Output HI Output STD Output HI Output STO Output @24 VDC UL max" @24 VDC UL max" @24 VDC UL max* @24 VDC - UL max" Horn 0.074 0.108 0.033 0.044 0.145 0.176 0.023 0.034 92 87 90 77 99 93 Bell 0.040 0.053 0.018 0.024 0.077 0.095 0.014 0.020 86 80 85 69 92 87 March Time Horn 0.067 0.104 0.033 0.038 0.109 0.142 0.023 0.034 89 84 89 74 99 93 Code-3 Horn 0.069 0.091 0.026 0.035 0.100 0.142 0.023 0.034 88 83 88 73 99 93 Code-3 Tone 0.061 0.075 0.026 0.035 0.088 0.105 0.015 0.021 85 80 84 70 95 90 Slow Whoop 0.069 0.098 0.028 0.037 1 0.100 0.142 0.025 0.035 90 89 89 75 99 94 Siren 0.080 0.104 0.027 0.036 0.122 0.152 0.021 0.030 89 84 89 75 98 93 HI!LO 0.044 0.057 0.020 0.026 0.089 0.114 0.018 0.026 86 81 86 71 93 88 * RMS current ratings are per UL average RMS method. UL max current rating is the maximum RMS current within the listed voltage range (16-33v for 24v Unite). For strobes the UL max current is usually at the minimum listed voltage (16v for 24v units). For audibles the max current is usually at the maximum listed voltage (33v for 24v units). For unfiltered FWR ratings, see installation instructions. -2- S WIRING DIAGRAMS 3. Contact Fenwal for"Installation Instructions" sheets on these products. These materials contain impor- MT SIGNAL tant information that should be read prior to specify- FROM ing or installing these products, including: PRECEDING + + TONEXI APPLIANCE. APPLIANON SEEDSM • Total current required by all devices connected to - OR FACP system primary and secondary power sources. i! ORDaIN • Fuse ratings on signaling circuits to handle maxi- mum inrush or peak currents from all devices on those circuits. SIGNAL • Composite flash rate from multiple strobes within a person's field of view. Installation in office areas and other specification and installation issues. Use strobes only on circuits with continuously applied operating voltage. Do not use strobes on coded or interrupted circuits in which the applied voltage is cycled on and off, as the strobe may not flash. The voltage applied to these products must be within their rated input voltage range. Conductor size (AWG), length and ampacity should be taken into consideration prior to design and installation of these products, particularly in AUDIBLE SIGNAL AND STROBE retrofit installations. OPERATE IN UNISON, RED AND 4. Fenwal notification appliances must be used within BLACK SHUNT-WIRES AM their published specifications and must be PROP- SUPPLIED. mom + _____Tf RED ERLY specified, applied, installed, operated, main- PRECEDING TO1IEXT APPLMC tamed and operationally tested in accordance with APPUANC FACP BU= --OREDI.R their installation instructions at the time of installa- tion and at least twice a year or more often and in + - accordance with local, state and federal codes, reg- ________ ulations and laws. Specification, application, installa- STROBE AUDIBLE bon, operation, maintenance and testing must be performed by qualified personnel for proper opera- tion in accordance with all of the latest National Fire Protection Association (NFPA), UnderwritersLabo- INSTALLATION NOTES ratories (UL), National Electrical Code (NEC), Occu- If the strobe and audible operate on the same cir- pational Safety and Health Administration (OSHA), cuit, add the strobe current from Table 3 to the audi- local, state, county, province, district, federal and ble current from Table 2. For Peak and Inrush other applicable building and fire standards, guide- current across the listed voltage range, refer to lines, regulations, laws and codes including, but not Installation Instructions, limited to, all appendices and amendments and the The average current indicated is per actual Produc- requirements of the local Authority Having Jurisdic- tion Testing at listed Vdc. For rated average and bon (AHJ). Peak current across the UL listed voltage range for ARCHITECTS AND ENGINEERS both filtered DC and unfiltered VRMS, see Installa- tion Instructions. Failure to comply with the installation Instruction sheets could result in improper installation, application, and/or operation WARNING of these products in an emergency situa- tion, which could result In property damage and serious injury or death. The notification appliance shall be a Fenwal MT Series audiblelvisual device or equivalent. Notification appliance shall be electronic and use solid state components. Elec- tromechanical alternatives are not approved. Each elec- tronic signal shall provide eight (8) field selectable alarm tones. The tones shall consist of: HORN, BELL, MARCH TIME HORN, CODE-3 HORN, CODE-3 TONE, SLOW WHOOP, SIREN AND Hl/LO. Tone selection shall be by durable dip switch assembly and not clips or jumpers. ,The Multitone Audible appliance shall be UL Listed under ORDERING INFORMATION Standard 464 for Audible Signal Appliances. The audible and the strobe shall be able to operate from a single noti- fication circuit while producing any of these tones. The device shall provide two output sound levels: STAN- DARD and HIGH dBA. The HIGH dBA setting shall pro- vide a minimum 5 dBA increase in sound output at nominal voltage. The HIGH anechoic dBA measurement at 10 feet at the alarm HORN SETTING shall be 99 dBA minimum. Operating voltages shall be 24 Vdc using fil- tered power or unfiltered power supply (full-wave-recti- fied). All models shall have provisions for standard reverse polarity type supervision and IN/OUT field wiring using terminals that accept #12 to #18 AWG wiring. Combination audible/visual appliances shall incorporate a Xenon fiashtube enclosed in a rugged Lexan lens or equivalent with solid state circuitry. Strobe shall produce a flash rate of one (1) flash per second minimum over the voltage range. The strobe intensity shall be rated per UL and Listed under Standard 1971 for Signaling Devices for the Hearing Impaired for 15/75 cd multi-candela with field selectable 15/30175/110 candela settings. The 15/75 can- dela strobe shall be specified when 15 candela or with 75 candela intensity on-axis is required. Strobe models shall incorporate circuitry for synchronized strobe flash and shall be designed for compatibility with Fenwal SM and/ or DSM Sync Modules. The strobes shall not drift out of synchronization at any time during operation. If, the mod- ule fails to operate (i.e., contacts remain closed), the strobes shall revert to a non-synchronized default flash rate. All Listed strobe appliances shall incorporate low temper- ature compensation to insure the lowest possible current consumption. Strobe activation shall be via independent input or from the same input circuit as the audible. The combination audible/visual appliances may be installed indoors and surface or flush mounted. They shall mount to standard electrical hardware requiring no additional trimplate or adapter. The aesthetic appearance shall not have any mounting holes or screw heads visible when the installation is completed. The appliance shall be finished in a textured red color. The audible device may be installed indoors or outdoors with the proper backbox. For weatherproof applications where specifications require 75 cd at -31°F (-35°C) and full temperature range of -31°F to 150°F, the Fenwal Model MTWP-2475W FR shall be used. Fenwal Is a registered trademark of Kidde-Fenwal, Inc. Lexan Is a registered trademark of the General Electric Company. Model Number Part Number Input Rated Strobe Mounting Voltage Candela Label Options MT-12124.R 75-000010.001 12124 - - B,H,LJ,K 15 MT-241575W-FR 75.000015-001 24 (75 FIRE 8.H.I,J.K - on AXIS) - 15 MT-241575W-AR 75.000015.002 24 (75 AGENT B.H,I,J,K - an AXIS) - MT.24MCW-FR 75.000018.001 24 15130175/ 110 FIRE B,H,I,J.K M124MCW.AR 75-000018.002 24 15/30/75/ 110 AGENT 8,H,I,J,K 1800 MI1NP-2475W-FR 75.000017.001 24 77F FIRE H Notes: MT-12/24 Audible can be used with Fenwal's RSSP Multi-Candela for applications requiring 15, 30, 75, 110 cd Wall Strobes. MTWP-2475W is weatherproof and rated for 180 cd @ 77°F (25°C) and 75 cd © -31°F (-35°C) with low current draw. SM Sync Modules are rated for 3.0 amperes at 12! 24 Vdc; DSM Dual Circuit Modules are rated for 3.0 amperes per circuit. Maximum number of intercon- nected DSM modules is twenty (20). Refer to Data Sheet 75-12. Use MT-241575W when 15 cd IS specified. 15/75 is UL Listed for 15 ad with 75 cd on AXIS. MOUNTING OPTIONS Model Number Part Number Mounting Options OBB-R - 75-000000-009 A ISP-R 75-000000-002 B WBB-R 75.000000-008 E LOB-R 75-000000-001 H RP-R 75.000000-003 .1 For complete installation options, refer to the Alarm Sig- nals Installation Data Sheet 75-008.A. .I assumes no responsibility for the product's suitability for a particular application. The I I.?I_III'L1\_II_•fL.-1S!_L, This literature is provided for informational purposes only. KIDDE-FENWAL, INC. I product must be properly applied to work correctly. I l>1 Protection Systems If you need more Information on this product, or If you have a particular problem or ques- I ton, contact I(IDDE-FENWAL, INC., Ashland, MA 01721. Telephone: (508) 881-2000. I A UTC Are & Security Company 400 Main Street Ashland, MA 01721 F-75-001 Rev AB © 2007 Kidde-Fenwal Inc. Printed in USA Ph: 508.881.2000 Fan 508.881.8920 www.fenwalfire.com CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7300-2007:0101 Page 1 of I CATEGORY 7300 - FIRE ALARM CONTROL UNIT ACCESSORIES/MISC. DEViCES LISTEE: JANUS FIRE SYSTEMSII02 Rupcich D, Crown Point, IN 46307 Contact: Edward Hugill (219) 663-1600 Fax (219) 6634562 Email: ehugiIljanusfiresystems.com DESIGN: Models MRS-1 Main/Reserve/Transfer, MAS-I Momentary Abort, LOS-1 Keyed Lock-Out, ARS-1 Abort/Releasing, and MMS-1 Momentary Releasing switch assembly stations. Model MRS-1 uses a DPDT toggle switch to transfer suppression system releasing circuits from a main supply to a reserve supply. MAS-1 uses a SPST pushbutton switch to provide pushbutton activated system abort capabilities. LOS-1 uses key activated DPDT switch to disconnect and electrically lock-out the releasing circuit of a fire suppression system. ARS.I uses both momentary SPST pushbutton switch and a momentary DPST toggle switch to combine the function of a Manual Release Station and Abort Station into a single unit. MMS-I uses a momentary DPST toggle switch to provide a non-maintained manually initiated release of fire suppression agent. Refer to listee's data sheet for additional detailed product description and operational considerations. RATING: MRS-1 Contact Rating (DPDT) - 250 VAC, 10 A MMS-1 Contact Rating (DPDT) -250 VAC, 10 A MAS-1 Contact Rating (SPST) -415 VAC, 4 A /110 VDC, 0.5 A LOS-1 Contact Rating (DPDT) -415 VAC, 4 A / 110 VDC, 0.5 A ARS-I Contact Rating (SPST) -415 VAC, 4 A/ 110 '/DC, 0.5 A ARS-I Contact Rating (DPDT) - 250 VAC, 10 INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating, and UL label. APPROVAL: Listed as miscellaneous control accesssones for use with listee 's separately listed compatible fire alarm control units. Authority having jurisdiction should be consulted prior to installation. 07-27-10 fm This listing is based upon technical data submitted by the applicant. CSFM Fire Engineenng staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2014 Listing Expires June 30, 2015 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No 7165-2007:0100 Page 1 of 1 CATEGORY: 7165— FIRE ALARM CONTROL UNIT (COMMERCIAL) LISTEE: JANUS FIRE SYSTEMSII02 Rupcich 0, Crown Point, IN 46307 Contact: Edward Hugill (219) 663-1600 Fax (219) 663-4562 Email: ehugilljanusfiresystems.com DESIGN: Model JFS-C1 fire alarm control unit. Automatic, manual, noncoded, local, remote station, central station, releasing device, waterfiow and sprinkler supervisory service. Refer to listee's data sheet for additional detailed product description and operational considerations. Suitable for use with the following modules: RA-4410RC, CA2Z, CAM, ARM-I, ARM-2, ARM-44 and MMS-I. INSTALLATION: In accordance with listee's printed installation instructions, applicable codes & ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating and UL label. APPROVAL: Listed as a fire alarm control unit when used with separately listed electrically and functionally compatible initiating and indicating devices. Suitable for high-rise applications when used with separately listed voice evacuation systems. Refer to listee's Installation Instruction Manual for details. These control units do not generate a Temporal Pattern Signal. If the distinctive three-pulse Fire Alarm Evacuation Signal (for total evacuation) in accordance With NFPA 72, 2002 Edition is required, the control unit must be used with appliances that can generate the temporal pattern signal. Model PFC-4410RC control unit meets the requirements of UL Standard 864, 9th edition. 07-01-10 fm This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing Is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other 0 Date Issued: July 01, 2014 Listing Expires June 30, 2015 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL _____ FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7270-1657:0109 Page 1 of 1 CATEGORY: 7270 - HEAT DETECTOR LISTEE: EDWARDS, A Division of UTC Fire & Security Americas Corporation, lnc.8985 Town Center Parkway, Bradenton, FL 34202 Contact Jewell Micochero (941) 739-4358 Fax (941) 308-8123 Email: rhonda.micochero@fs.utc.com DESIGN: Models 281A, 281B, 281 AM, 281 AR, 281 AL, 281 AF, 282A, 282B, 282AM, 282AR, 282AL, 282AF, 291 B and 292B combination fixed temperature/rate-of-rise heat detectors; Models 283A, 283B, 283AM, 283AR, 283AL, 283AF, 284A, 284B, 284AM, 284AR, 284AL, 284AF, 293B, 294B, 445, 446, 6290B-281 and 6290B-283 fixed temperature heat detectors. Models may have suffix -F or -PL. Refer to listee's data sheet for detailed product description and operational considerations. RATING: 283, 291, 293, 445, 6290B-281/283: 135oF 284, 292, 294, 446; 194oF INSTALLATION: In accordance with listee's printed installation instructions, applicable codes & ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, temperature/electrical ratings and UL label. APPROVAL: Listed as fixed temperature and/or combination fixed temperature/rate-of-rise system heat . detectors for use with separately listed compatible bases and fire alarm control units. NOTE: Formerly 7270-1591:109, 7270-1388:113 and 7270-0073:039 7-29-10 ma This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct IV% operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other 0 Date Issued: July 01, 2014 Listing Expires June 30, 2015 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM is LISTONG SERVICE LISTING Na. CATEGORY: LISTEE: 7770-0328:0141 7770 - VALVES/SWITCHES Potter Electric Signal Co1609 Park 370 Place, Hazelwood, MO 63042 Contact: Bill Witherspoon (314) 595-6900 Fax (314) 595-6999 Email: BillWpottersignaI.com Page 1 of I DESIGN: RATING: INSTALLATION: MARKING: APPROVAL: NOTE: Models PSI 0-EX and PS40-EX pressure operated switches. Refer to listee's data sheet for detailed product description and operational considerations. IDA, 125-250 VAC; 2.5A, 0-30 VDC In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. Listee's name, model number, rating and UL label. Listed as pressure switches for use with fire sprinkler systems. Suitable for use in hazardous locations, Class I, Group B, C and D; Class II, Group E, F and G. S *Rev 6-20-2002 iz This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2014 Listing Expires June 30, 2015 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL S FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7272-0410:0107 Page 1 of I CATEGORY: 7272 -- SMOKE DETECTOR-SYSTEM TYPE-PHOTOELECTRIC LISTEE: Hochiki America Corporation7051 Village Drive, Ste. 100, Buena Park, CA 90621-2268 Contact: Michael Urn (714) 670-3248 Fax (714) 522-2268 Email: mum@hochiki.com DESIGN: Models SLG-12, SLG-24, SLG-24FH, SLG-24F, SLK-12, SLK-24F, SLK-24FH, SLK-24FB, SLK-24FL, SLK-24FLB, SLK-835, SLK-835H, SLR-835, SLR-835W, SLR-835B-2, SLR-835B-4, SLR-835B-2W, SLR-835B-4W, SLR-24, SLR-24H, SLR-24V, *SLR..24vN SLR-835H, SLR-835HW, SLR-835BH-2, SLR-835BH-2W, SLR-835BH-4, SLR-8358H-4W photoelectric type smoke detectors. Unit with suffix -H or -FH employs a supplemental heat sensor. Refer to listee's data sheet for additional detailed product description and operational considerations. RATING: 12 VDC and 24 VDC INSTALLATION: In accordance with listee's printed installation instructions, applicable codes & ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model designation, electrical rating and UL label. APPROVAL: Listed as photoelectric smoke detectors for use with separately listed compatible fire alarm control units when used in conjunction with listee's listed bases (CSFM Listing No. 7300-0410:132). Models with supplemental heat sensor are not approved for use in lieu of 5 required heat detectors. NOTE: Formerly 7257-0410:107 *Rev 2-14-2003 IPI This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other 110 Date Issued: July 01, 2014 Listing Expires June 30, 2015 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7135-1076:0134 Page 1 of I CATEGORY: 7135 —AUDIBLE DEVICES LISTEE: KIDDE-FENWAL, INC400 Main Street, Ashland, MA 01721 Contact: Terrill Garland (508) 881-2000 Fax (508) 881-1773 Email: terriII.garlandkidde-fenwaI.com DESIGN: Model MT-12124 multi-tone audible device followed by R to indicate package color. Refer to listee's data sheet for additional detailed product description and operational considerations. RATING: 12(9-15.6 VDC) 24 (18-31 VOC) INSTALLATION: In accordance with Iistee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. Surface mounted and suitable for outdoor with Model lOB back box. MARKING: Listee's name, model number, electrical rating and UL label. APPROVAL: Listed as an audible signaling device for use with separately listed electrically compatible fire alarm control units. Refer to listee's Installation Instruction Manual for details. If the distinctive three-pulse Temporal Pattern Fire Alarm Evacuation signal (for total evacuation) in accordance with NFPA 72, 2002 Edition is required, the appliances must be used with control units that can generate the temporal pattern signal. XLF: 7135-0785:0118 *Corrected 02-16-10 fm " "' . A This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not AN an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2014 Listing Expires June 30, 2015 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHA!. FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM is LISTI NG SERVICE LISTING No. 7125-1076:0169 Page 1 of I CATEGORY: 7125-. FIRE ALARM DEVICES FOR THE HEARING IMPAIRED LISTEE: KIDDE-FENWAL, INC400 Main Street, Ashland, MA 01721 Contact: Terrill Garland (508) 881-2000 Fax (508) 881-1773 Email: terrill.garland©kidde-fenwal.com DESIGN: Models MT-241575W-FR, MT-241575W-AR, MT-2476W-FR, MT-2475W-AR, *MT..24MCW..AR and *MT24MCW.FR multitone sync horn/strobes. The 24 and 75 in model designation indicates voltage and candela rating. The W indicates wall mount, followed by two alpha characters indicating lettering and color. The series can provide one of eight tone outputs. *Models MT-24MCW-AR, and MT-24MCW-FR, may be followed by a letter indicating enclosure color. Refer to estee's data sheet for additional detailed product description and operational considerations, RATING: Electrical: 16*33 VDC Flash rate: 60 flashes/mm Candela: Models 1575:15cd (75cd on axis) Models 75:75cd *Models MCW:l5cd,30cd,75cd, or ll0cd INSTALLATION: In accordance with listee's printed installation instructions, NFPA 72, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. For wall mount only. MARKING: Listee's name, model number, electrical/candela rating, and U!. label. APPROVAL: Listed as horn/strobes suitable for the hearing impaired when used in conjunction with separately listed electrically compatible fire alarm control units. For indoor use only. For synchronized strobes, Models SM-I2l24 or DSM-12124 Sync Module (CSFM Listing No. 7300-1076:153) must be used. Refer to listee's Installation Instruction Manual for details. These units can generate a distinctive three-pulse Temporal Pattern Fire Alarm Evacuation Signal (for total evacuation) in accordance with NFPA 72, 2002 Edition. XLF: 7125-0785:0155 *Rev. 01-02-05 This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not i WN an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2014 Listing Expires June 30, 2015 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL [I m-~ q _ FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING LISTING No. 7135-1076:0127 Page 1 of I CATEGORY: 7135 - AUDIBLE DEVICES LISTEE: KIDDE-FENWAL, INC400 Main Street, Ashland, MA 01721 Contact: Terrill Garland (508) 881-2000 Fax (508) 881-1773 Email: terrill.ga.land©kidde-fenwal.com DESIGN: Model MB-G6-24-R and MB-GIO-24-R motor bells. Suitable for outdoor use when used with Model WBB backbox. Refer to listee's data sheet for detailed product description and operational considerations. INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating and UL label. APPROVAL: Listed as audible devices for use with separately listed compatible control units. If this appliance is required to produce a distinctive three-pulse Temporal Pattern Fire Alarm Evacuation Signal (for total evacuation) in accordance with NFPA 72, 2002 Edition, the appliance must be used with a fire alarm control unit that can generate the temporal pattern signal. Refer to manufacturer's Installation Manual for details. XLF: 7135-0785:0113 Rev. 06-21-2003 This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, Installation instructions andlor other Date Issued: July 01, 2014 Listing Expires June 30, 2015 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7300-0410:0132 Page 1 of 2 CATEGORY: 7300 -- FIRE ALARM CONTROL UNIT ACCESSORIES/MISC. DEVICES LISTEE: Hochiki America Corporation7051 Village Drive, Ste. 100, Buena Park, CA 90621-2268 Contact: Michael Urn (714) 670-3248 Fax (714) 522-2268 Email: mum@hochiki.com DESIGN: Detector bases (2 and 4-wire). Unit is intended for use with a separately listed compatible detector head. Refer to listee's data sheet for detailed product description and operational considerations. Models listed below. HA-4W HA-4W1 HA-4WX HA-2 HA-SL HA-SR HA-SLR HA-RA2 HA-NRA2 HA-L1 2R HA-2R HA-22R HA-1-2 HA-1-2A HA-L2R HA-1-22 HA-1-22A HA-1-22F HA-1-22R HA-1-22S HA-LA2 HA-LRA HA-LRA2 HA-LNA2 HA-LNRA2 HS-2 HS-21- HS-21) HS-21 HS-21L HS-21D HS-22 HS-22L HS-22D HS-100 HS-2000 HS-220 HS-220L HS-220D HS-221 HS-221L HS-221D HS-221X HS-221XL HS-221XD HS-224 HS-224L HS-224D HS-225 HS-225L HS-225D HS-2RB HS-21 RB HS-220RB HS-221 RB HS-224RB HS-2RB4 HSB-2 HSB-2N HSB-12-1 HSB-12-IN HSB-12-4 HSB-12-4N HSB-21 HSB-21N HSB-100 HSB-200 HSB-200N HSB-220 HSB-220N HSB-221 HSB-221N HSB-2215 HSB-224 HSB-224N HSB-225 HSB-225N HSC-4R HSC-21L HSC-220L HSC-220R HSC-221 L HSC-221 R HSC-224RA HSC-224L HSC-224R HSC-225L HSB-DCP-6 HSB-NSA-6 YBA-M2 YBA-M21 YBA-M22 YBA-M220 YBA-M221 YBA-M224 YBA-M225 YBA-M 100 YBA-MAP YBA-R3 YBA-RL/4 YBA-R114-1 YBA-RL/4-2 YBA-RL/4-RA YBC-RL/12 YBC-RLI12-1 *Rev 01-12-12 gt This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other 40 Date Issued: July 01, 2014 Listing Expires June 30, 2015 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division Listing No. 7300-0410:0132 Page 2 of 2 YBC-RLII2-2 YBC-RL/12-4 Y13C-RLI4-RA YBC-RL/2NC . YBC-RLI2NBE YBJ-RL/2ND YBN-RI2NA YBN-NSA-4 NS4-1 00 NS4-220 NS4-221 NS4-224 NS6-100 NS6-220 NS6-221 NS6-224 *FFO4BASE *FFO6BASE *FFOSBASE Models may or may not come with suffix -W. INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating and UL label. APPROVAL: Listed as bases for use with listee's separately listed compatible smoke and heat detectors. Refer to heat or smoke detector listings for compatibility. Models HA-2R, HA-SLR, HA-LRA2 and HSC Series w/ suffix R are also suitable for releasing device service. Model YBA-R3 is intended for use with thermostat detector only. NOTE: Formerly 7300-0410:100, 106, 115, 124, 125, 126, 130, 131 & 133 I *Rev 01-12-12 gt This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other 0 Date Issued: July 01, 2014 Listing Expires June 30, 2015 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division