The URL can be used to link to this page

Home My WebLink About1950 CAMINO VIDA ROBLE; ; FS090010; Permit10/29/2020 FS0900I0 Permit Data City of Carlsbad Fixed Systems Permit 1950 CAMINO VIDA Job Address: ROBLE Permit Type: FIXSYS Parcel No: 2120931200 Lot #: 0 Permit No: FS0900I0 Status: ISSUED Applied 2/24/2009 Approved: 2/24/2009 Reference No.: Issued: 2/24/2009 PC #: Inspector: Project Title: JITTERBUG SPECIAL CHEMICAL SUPPRESSION SYSTEM Applicant: FACILITIES PROTECTION SYSTEMS SUITE D 1150 W.CENTRALAV BREA, CA Owner: CARLSBAD CC L P C/O MATTHEW J ROOT 10188 TELESIS CT #222 SAN DIEGO CA Fees ($) Add'I Fees ($) Total ($) Balance ($) [ 130 0 130 1 0 5QC tw PASSIFAIL Enclosure Integrity Report Q5 CleanAgent 2001 retention time prediction program revision 2.5.4. Complies with NFPA 2001 Appendix C, year 2000 edition. By Retrotec, Inc, 2200 Queen Street, Bellingham, WA USA 98229 360-738-9835 www.retrotec.com Software Licensed to: Facilities Protection Systems Inc air leaks in 4 Building, Location JITTERBUG, CARSLBAD, CA Company, Contact BURGER CONSTRUCTION, JOHN ARGUELLO FILE COPY Room name SERVER ROOM / MDF Test number I Calibration Certificate #3246 Certificate created 2008/06/11 agent leaks out Test date/time 200910511113:30 Net Protected Volume, V 3,650 ft'3 Tester Sample Tech Maximum Protected Height, Ho 10.00 ft. Certified to Level: 4 - ISO multi-point & vent test Minimum Protected Height, H 8.50 ft. Signature ......................................................Static during retention, PSH 0.0 Pa Elevation above sea level 0 ft Operating temperature 70 F Correction method NFPA 2001 (2000) Formula A-3-5.3..3 Initial concentration, C 8.04% Correction factor I Mixing during retention No Agent FE-25 (HFC-125) Agent quantity 101 lb. Total room leakage, ELA 0.31 ft*2 Minimum concentration, CF 8.04% Lower Leakage, BCLA 0.15 ftA2 Minimum retention time 10.0 minutes Below ceiling leakage defaulting to worst case -- 50% of total leakage. This enclosure was tested in compliance with NFPA 2001 and 12A. Assuming no continual mixing dung the retention period, enclosure leakage could allow sufficient agent to be lost to cause an air/agent interface to descend from a Maximum Protected Height of 10.00 ft. to the Minimum Protected Height specified of 8.50 ft. The retention time would then be 11.8 minutes which exceeds the minimum retention time of 10 minutes. The enclosure therefore gasses this acceotance orocedure. Notes Witnesses Printed on: 2009/05/1112:59 Page 1 DOOR FAN TEST -- Total Room Leakage Data CleanAgent 2001 retention time prediction program revision 2.5.4. Complies with NFPA 2001 Appendix C, year 2000 edition. By Retrotec, Inc, 2200 Queen Street, Bellingham, WA USA 98229 360-738-9835 www.retrotec.com Software Licensed to: Facilities Protection Systems Inc air leaks in Building, Location JITTERBUG, CARSLBAD, CA Company, Contact BURGER CONSTRUCTION, JOHN ARGUELLO Room name SERVER ROOM / MDF Test number I Calibration Certificate #3246 Certificate created 2008106/11 agent leaks out Total Room Leakage Operator In the room Smoke doesn't move Temperature during test (F) Static pressure 0 Pa 70 inside 70 outside Pressurization Range for room pressures: 10.0 to 13.0 I Blower range Room pressure 10.5 Auto corrected RP 10.5 Ring Cl Flow Pressure 118 Auto corrected FP 118 Corrected flow (ftA3/min.)l 1591 ELAftA2 @Pa FA I Depressurization 0.30 11.0 Pressurization 0.32 10.5 Average 0.31 10.8 0.50 I [i7 it 0.5000 46.29 NA NA I 0.5000 49.13 NA NA r0.5000 47.71 1 0.31 1 10.0 10,50 Lower Leakage Below ceiling leakage of 0.15 ftA2 @ 10.6 Pa is the worst case assumption of 50% Technician: Sample Tech Certified to Level: 4- ISO multi-point & vent test Yes Level 1 - Fire enclosure design basics for improving agent retention and passive protection Yes Level 2 - adds single door fan operation and NFPA clean agent retention time calculations Yes Level 3 - adds double door fan operation for Lower Leak measurement Yes Level 4 - adds multi-point ISO door fan operation and discharge pressure relief vent Printed on: 2009/05/1112:59 Page 2 DOOR FAN TEST -- Graph CleanAgent 2001 retention time prediction program revision 2.5.4. Complies with NFPA 2001 Appendix C, year 2000 edition. By Retrotec, Inc, 2200 Queen Street, Bellingham, WA USA 98229 360-738-9835 www.retrotec.com Software Licensed to: Facilities Protection Systems Inc air leaks in Building, Location JITTERBUG, CARSLBAD, CA Company, Contact BURGER CONSTRUCTION, JOHN ARGUELLO Room name SERVER ROOM / MDF Test number I Calibration Certificate # 3246 Certificate created 2008/06/11 agent leaks out ,. . ................ 10 4- 0.1 1.0 10.0 100.0 1000.0 Room Pressure (Pa) -a- Total leakage, depressurizing -.- Total leakage, pressurizing - Total leakage, average -D- Lower leakage. depressurizing -- Lower leakage, pressurizing -- Lower leakage, average Printed on: 2009/05/1112:59 Page 3 One Year Calibration Certificate Certificate # 3246 System Model # Q5E System Owned By Facilities Protection Systems Inc Console # For CA2001 ver 2.0 license # Equipment Calibrated by Retrotec Inc Good for one year date: 2008/06/11 expires: 2009/06/11 This certificate complies with calibration requirements of NFPA 2001 Appendix C, year 2000 edition and ISO 14520. Completed by Retrotec Inc, 2200 Queen Street, Bellingham, WA, USA 98226-4766 DM-2 MklI This gauge used for All Readings serial# 101311A to correct mult by & add gauge CR MRC error Pa 0.00 - 1,250.00 1.00 0.00 0.0 10.0 0.0 0.0 DM-2 MklI This gauge used for All Readings serial# 101311B to correct mult by & add gauge CR MRC error Pa 0.00- 1,250.00 1.00 0.00 0.0 10.0 0.0 0.0 CR is the Corrected Room pressure. CR = "gauge" reading X "mult by" factor + "& add" factor. CF is the Corrected Flow pressure derived the same way. The corrected readings are compared to the TRUE reading from our Master Reference Calibration (MRC) gauge and the resulting error shown in Pascals. Maximum allowable error is +1- 1 Pa from 0 to 50 Pa and Pa over over 50 Pa. Five Year Calibration Certificate Certificate # 3246 System Model # WE System Owned By Facilities Protection Systems Inc Console # For CA2001 ver 2.0 license # Equipment Calibrated by Retrotec Inc Good for five years date: 2008/06/11 expires: 2013/06/11 This certificate complies with calibration requirements of NFPA 2001 Appendix C, year 2000 edition and ISO 14520. Completed by Retrotec Inc, 2200 Queen Street, Bellingham, WA, USA 98226-4766 CALIBRATION EQUATIONS WITH CALCULATION EXAMPLES: blower #1 serial #>> J 096613 blower range N K KI K2 K3 K4 MF CR FF cfm m3 /sec #1 22 0.5214 486.9900 -0.070 0.800 -0.115 1.032 86 #1 A 0.5030 259.0380 -0.075 1.000 0.000 1.056 120 #1 B 0.5008 159.8360 -0.035 1.000 0.000 1.048 100 #1 C8 0.5025 77.4180 -0.030 1.200 0.004 1.044 iao - #1 C4 0.4950 42.4.482 0.045 1.200 0.011 1.039 120 #1 C2 0.4655 24.8640 0.400 1.200 0.008 1.189 120 #1 Cl 0.4773 13.3493 10.320 1.200 0.004 1 1.256 12.0 1 BLOWER TEST RESULTS: error Holes I blowerl range I cm2 % I cm2 This calibration certificate compares the calibration holes in the Retrotec test chamber with the tested blower's measurement of those holes. The left hand column shows the area of holes open in the Retrotec flow chamber. To the right is the comparable Retrotec Door Fan result using the above referenced CA200I software license. Maximum allowable error is +1- 5%. This calibration includes both gauge and blower error combined. CR and CF come from the One Year Certificate. For Flow Towards the operator, CF must be reduced by CR before calculating flow to yield FF, the symbol for the Final Flow pressure. For Flow Away from the operator CFFF. FF must be >=MF and (CR '1(2) otherwtse flow pressure is too low for accurate results Flow in cfm = (FF.CR*K1)N*(K+K3*FF)*K4 For m3/sec divide by 2118.882. Technician: Sample Tech Certified to Level: 4-ISO multi-point & vent test Yes Level 1 - Fire enclosure design basics for improving agent retention and passive protection Yes Level 2 - adds single door fan operation and NFPA clean agent retention time calculations Yes Level 3 - adds double door fan operation for Lower Leak measurement Yes Level 4 - adds multi-point ISO door fan operation and discharge pressure relief vent HFC-125 DETECTION AND CONTROLS ENGINEERING SUBMITTAL FOR JITTERBUG 1950 CAMINO VIDA ROBLE CARLSBAD, CA 92008 02-12-09 PROVIDED BY: Facilities Protection Y-LL.'JJLL) ZE OS for life sfety and business continuity 1150 W. CENTRAL AVE. SUITED BREA, CA 92821 TEL: 714-257-2244 FAX: 714-257-2240 C.L.#592289-C10/C16 Az APPR9IV AS SUBMITTED CAI'1E DEPARTMENT F3100 il CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL - - FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7165-0900:135 Page 1 of 1 CATEGORY: Control Unit (Non High-Rise) LISTEE: Fike Protection Systems, 704 S. 10th St., Blue Springs MO 64015 Contact: Brent Mlika (816) 229-3405 X 1220 FAX (816) 229-5082 DESIGN: Model SHP PRO 10-2452 control unit with releasing device service. Includes main controller, transformer, and enclosure. Local, remote, and central station service. Refer to listee's data sheet for detailed product description and operational considerations. System components: 10-2452 Main Controller 10-2450 Class A Input Module 10-2448 Class A Output Module 10-2204 CRM4 Relay Module 10-2453-R(G) Enclosure INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating, and UL label. APPROVAL: Listed as a fire alarm control unit for use with separately listed compatible initiating and indicating devices. Refer to listee's Installation Instruction Manual for details. This control unit does not generate a temporal pattern signal. If the distinctive three-pulse Temporal Pattern Fire Alarm Evacuation signal (for total evacuation) in accordance with NFPA 72, 2002 Edition is required, the control unit must be used with appliances that can generate the temporal pattern signal. This control unit meets the requirements of UL-864, 9th Edition Standard. NOTE: For Fire Alarm Verification Feature (delay of fire alarm signal), the maximum Retard/Reset/Restart period shall not exceed 30 seconds. 08-20-2004 This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources. Date Issued: JUNE 10, 2008 Listing Expires June 30, 2009 Authorized By: BEN HO, Chief Fire Engineering Division Ak SHP PRO DESCRIPTION The Fike SHP PROTM, (P/N 10-063) is a Conventional Control system designed to provide a sophisticated, reliable conventional detection system for use with clean agent extinguishing, sprinkler pre-action/deluge, watermist, watertlow alarm and fire alarm systems. It is a microprocessor based system which can he easily configured for a wide range of suppression applications. The SHP PRO is designed for use with Fike Clean Agent Fire Suppressant, CO2, or sprinkler (pre_action/deluge) suppression systems. The main controller contains all electronics required for a complete detection and control system suitable for most applications. Optional modules, which plug into the main circuit board, are available to add increased functionality to the system. The SHP PRO provides 10 Status LEDs AC Normal, Alarm , PreDischarge, Release, Supervisory, Trouble, Panel Silenced, Abort, Release Disabled, Ground APPROVALS Fault) for instant feedback. A diagnostic LED display is provided to help trouble UL S2203 shoot any potential field problems, provide current status and retain stored events. FM 3017159 A Reset and Silence switch is provided to allow control of the system outputs and CSFM 1765-0900: 135 operation. . MEA 461-04-E The SHP PRO can be configured for either one or two conventional detection circuits. The detection circuits can be configured for sequential detection, cross zone or single detector release. Depending on the configuration selected, the SHP PRO also provides up to three initiating circuits to monitor contact devices (Abort, Manual Release, Waterfiow or Supervisory switches). Four different abort types are available including a special NYC option. All five initiating circuits can be converted to Class A operation via the SHP PRO Class A Input Module, P/N 10-2450. All SHP PRO initiating circuits are inherently power limited. A twelve position dip switch is used to set all options. Three notification appliance circuits, rated for 2 amps @ 24 VDC are available. Depending on the configuration, each circuit will provide distinct signaling for Alarm, PreDischarge, or Release conditions. Separate Agent Release and Solenoid circuits are provided to operate the suppression system. A dedicated Disable switch is provided for release and audible outputs. All output circuits, including solenoid and agent release circuits, are power limited. The SHP PRO provides dedicated alarm, trouble and supervisory SPDT contacts for annunciation and control. If additional outputs are required, up to two CRM4 Relay Modules can be added. (P/N 10-2204) The SHP PRO is available in multiple hardware configurations, depending on the input power source (120 or 240 VAC), enclosure color (Gray or Red), and mode of operation (Clean Agent, Clean Agent/ Sprinkler, Sprinkler, Watermist, Solenoid Releasing). The system comes equipped with a 4.0 amp @ 24 VDC power source. The system has been designed to comply with the following standards: NFPA 12 Carbon Dioxide NFPA 12A Halon 1301 Extinguishing Systems NFPA 13 Installation of Sprinkler Systems NFPA 15 Water Spray Fixed Systems NFPA 16 Deluge, Foam-water and Foam-spray Systems NFPA 70 National Electric Code NFPA 72 Installation, Maintenance and Use of Protective Signaling Systems NFPA 2001 Clean Agent Fire Extinguishing Systems I Form No. D.1.07.01-5 704 S. 10th Street P.O. Box 610 Blue Springs, Missouri 64013-0610 U.S.A. (816) 229-3405 (816) 229-4615 www.fike.com o il 0— h. : . o a: 0 FEATURES Suitable for multiple types of Suppression: Clean Agent, Carbon Dioxide, Pre-Action Sprinkler/Deluge, and Watermist Systems Microprocessor based with hardware and software integration designed to guarantee reliability Cross zone, sequential manual release, abort, water flow and supervisory detection types Three Class B, Style Y notification appliance circuits rated for 2.0 amps @ 24VDC Dedicated release circuits compatible with agent release or solenoid actuation Five Class B, Style B initiating circuits Optional Class A modules for notification appliances /releasing circuits and initiating circuits Alpha-numeric LED display for stis and troubleshooting Programmable pre-discharge and di arge timers Resettable and continuous auxiliary output power integral 4.0 amp power supply Small surface or flush mount enclosure with removable door Approved for releasing device service and sprinkler supervisory Built-in Gentex and System Sensor synch protocol Steel enclosure 21" x 14.35" x 4" Enclosure equipped with .50" wide lip for flush mounting SHP PROTM WIRING DIAGRAM COMPONENTS 10-063-X-X-X 10-063-X-X-X A B C 1-Clean Agent/All Modes 2-Spiirikler only R-Red G-Gray 1- 120 VAC 2- 240 VAC 10-2452-1 PCB Assy, SHP PRO, Clean Agent, All Modes 10-2452-2 PCB Assy, SHP PRO, Sprinkler Only 10-2450 Class A Input Module 10-2448 Class A Output Module 10-2204 CRAM Relay Module 10-2190-1 Battery Assembly (Qty 2), 7AH, w/ wiring assembly 10-2190-2 Battery Assembly (Qty. 2), I8AH, w/ wiring assembly Fc!ke Copyright © Fike Corporation All Rights Reserved. R P0 RAT I ON Form No. D.1.07.01-5 September, 2005 Specifications are subject to change without notice. CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 6760-0900:103 Page 1 of 1 CATEGORY: Electrical Switches LISTEE: Fike Protection Systems, 704 S. 10th St., Blue Springs MO 64105 Contact: *Brent Mlika (816) 229-3405 ext 1220 FAX (816) 229-5082 DESIGN: Models 10-1638 thru 10-1641, 10-1643 thru 10-1652, 20-040 and 20-046 auxiliary switches for various function (manual release, abort, main reserve, reset with or without timer assembly for releasing agent control). Refer to listee's data sheet for detailed product description and operational considerations. INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number and UL label. APPROVAL: Listed as electrical switches. *Rev. 04-18-2005 This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources. Date Issued: JUNE 10, 2008 Listing Expires June 30, 2009 Authorized By: BEN HO, Chief Fire Engineering Division DOUBLE COMBINATION CONTROL ACCESSORIES DESCRIPTION The Manual Release Switch is a dual actuation device which provides a means of manually discharging the automatic fire extinguishing system when used in conjunction with the Fike control panel. The System Abort Switch is designed to be used in conjunction with other system equipment. It provides a temporary manual means by which the agent actuation circuit may be interrupted before automatic actuation occurs. The "Main" to "Reserve" switch is used with systems that incorporate main and reserve (back-up) agent storage. The switch may utilize I or 2 Form "C" contact bl ks which will provide an electrical path to either the "Main" or "Reserve" release device(s). The Keyed Remote Reset Switch provides a method for resetting the Control Panel from a remote location. These combination controls mount on a standard 4 gang masonry electrical box measuring 7-3/8" (187.3mm) wide x 3-3/4" (95.3mm) high x 2-3/8" (60.3mm) deep. (Fike P/N 02-2123) 10-1643 Manual Release/System Abort 10-1644 Manual Release/Main Reserve 10-1645 Manual Release/Remote Reset 10-1646 System Abort/Main Reserve 10-1647 System Abort/Remote Reset 10-1648 Main Reserve/Remote Reset APPROVALS UL Listed ULC Listed FM Approved CSFM Approved BSA - 610-79-SA Form No. P.1.73.01-1 I 704 S. 10th Street P.O. Box 610 Blue Springs, Missouri 64013-0610 U.S.A. - (816) 229-3405 (816) 229-4615 www.fike.com 3507 KEYED- MAINTENANCE BY-PASS SWITCH GENERAL This maintenance panel is a key-switch that disconnects actuation circuits in the system to prevent accidental discharge during maintenance operations. Two LEDS indicate "SYSTEM ARMED" or "SYSTEM INACTIVE" when the key is inserted and turned. The "SYSTEM INACTIVE" indicator flashes intermittently. The key can only be removed in the armed position. The maintenance panel mounts to a 4" junction box and operates on 24VDC. The information is silk screened on a 2 gang stainless steel plate. It is designed for mounting on the wall to a bell box. OPERATION Operation of the ARM disconnect is through a two position key switch. When activated, the ARM disconnect immediately "opens" the releasing circuit making it impossible for the releasing panel to activate the suppression system. The ARM disconnect maintains circuit supervision by placing the releasing control panel into a trouble condition whenever the key switch is in the disconnect position. TECHNICAL CONTACT BLOCK: V50 N.C. FULLY INSULATED - THERMOPLASTIC CONTACT RATING: 3 AMP @600VAC CONTACTS DOUBLE BREAK SILVER STACKABLE SNAP BLOCK GEMCOM, INC. 8828 S. Archer Avenue, Willo Springs, IL 60480-1204 1-800-871-6840 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7272-1653:122 Page 1 of 1 CATEGORY: Photoelectric Smoke Detector LISTEE: System Sensor, Unincorporated Div of Honeywell Int'l Inc., 3825 Ohio Ave, St. Charles, IL 60174 Contact: Trish Linhart (630) 377-6580 ext. 1185 FAX (630) 377-7245 DESIGN: Model 2100, 21001, 2112TL, 2112/24, 2112/24B, 2112/24D, 2112/24T, 2112/24TB, 2112/24TD, 2112/24TSR, 2112/24TSRB, 2100D, 2100TD, 2151 and *2151T photoelectric smoke detectors. Models 2100, 2100T, 2100D, 2100TD, 2151 and *2151T are 2-wire and Models 2112TL, 2112/24D, 2112/24TD, 2112/24, 2112/2413, 2112/24T, 2112/24TB, 2112/24TSR and 2112/24TSRB are 4-wire. Model with suffix -T employs a 1350 fixed temperature supplemental thermistor type heat sensor. This thermal circuitry is NOT approved for use in lieu of required heat detectors. Refer to listee's data sheet for additional detailed product description and operational considerations. RATING: Electrical: 8.5 to 32 VDC INSTALLATION: In accordance with listee's printed installation instructions and applicable codes and ordinances. Suitable in open areas with air velocities between 0-3000 ft/mm. MARKING: Listees name, model number, electrical rating and UL label. APPROVAL: Listed as photoelectric smoke detectors when used in conjunction with separately listed compatible fire alarm control units and bases. For wall and ceiling mount. Refer to listee's Installation Instruction Manual for details. NOTE: 1. Model 2151 and *2151 T is also suitable for use inside ducts when used with listed Models B114LP and B114LPBT (7300-1653:109) detector bases. 2. Formerly 7272-1209:159 *Rev 03-13-20061w This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources. Date Issued: JUNE 4, 2008 Listing Expires June 30, 2009 Authorized By: BEN HO, Chief Fire Engineering Division Models Available *2151 Photoelectric Detector 2151T Photoelectric Detector with thermal Product Overview Sleek, low-profile design System Sensor 100 Series Plug-in Smoke De1.ectors offer superb performance ant reli- Compatible with 400 Series product ability in a profile which is just 2 (5.1 cm) deep. Model 2151 (photoelectric sensor) and model 21511 (photoelectric sensor with thermal) can be used with a varialy f Two LEDs blink in standby, providing different adapter bases in several wiring configurations and voltages. Other fearures 360° visibility incude low current draw, stable performance in high air velocities, built-in tarroer resistant base design, remote LED option, removable cover, and built-in test stch. DOdU range Ui dUIPLUF bases dVdLiUI with built-in shorting spring he 100 Series is designed to meet the performance criteria designated by dL. Hand-held sensitivity reader available Its sensing chambers are sealed against back pressure air flow, dirt, and insects. This chamber is protected by a fine mesh screen which can be clea:ied o: reçlaced. Additional key features include a variety of mounting ba.ss ani a full line of accessories. All 100 Series photoelectric smoke detectors contain a unique optical seLsing chamber designed to sense smoke particles produced by a wide range of ccm- bution sources. A custom integrated circuit incorporates signal pruce sing to reduce false alarms. Model 2151 photoelectric detector's unique optical sensing chamber is engi- neered to sense smoke by a wide range of combustion sources. Dual electronic thernistors add 135F fixed temperature thermal sensing on model 2152.1. LISTED S911 7272-1653:122 CS308 MEA MSFM approved APPROVED approved 205-94-E 0X5A4.AY 1973 Specifications Operating Voltage/Alarm Current See Adapter Base Selection Guide following Standby Current 851jA Standby Sensitivity 1 - 3.18%/ ft. Height 2.0" in B401 Diameter 4.1" installed in B401 6.2' installed in l3110LP Shipping Weight 5.20z Const ruction Flame retardant thermoplastic Temperature Photo: 32°F to 120°F (0° to 49°C) Photo/thermal: 32°F to 100°F (0° to 38°C) UL Listed Velocity Range Photo: D - 3000 fpm (0 - 15.2 rn/a) Smoke Detector Spacing On smooth ceilings (as defined in NFPA 72), spacing of 30 feet (900 sq. ft.) may be used as a guide. Other spacing may be used depending on ceiling height, high air movements, and other conditions or response requirements. Humidity Range 10% - 93% RH non-condensing Adapter Base Selection Guide Base Model Number Loop Type Current Limit Resistor Contact Type Nominal Voltage Current Draw on Alarm (mA) B11OLP/84011 2wire* No - 12/24VDC 10_130** B11ORLP/B401Rt/B401BRt 2-wire* Yes - 24VDC 10-62 B112LP/8402t 4-wire Yes Form A&C 24VDC 17-36 B114LP/B404t 4-wire Yes Form A&C + A Supervisory 120VAC 75 mA AC Max B116LP/B406t 2.wire* No Form C 24VDC 20100 B401t 2wire5 I No - 12/24VDC 10-130° "Functionality contingent on panel compatibility —Must be limited by control panel iFlangeless base Relay contact Ratings: Resistive or Inductive (60% power factor) load. Form A: 2.05 at 30 VAC/DC Form C: 0.6A at iiovoc, 2.05 at 30VDc 1.OA at I25VAC, 2.OA at 30VAC Junction Box Selection Guide* Base Model Number Single Gang 314" Octagon 4' Octagon 4' Square 50 mm 60 mm 75 mm B401 NO NO NO NO YES YES NO B11OLP/RLP YES YES YES YES NO NO NO B112LP/8116LP YES YES YES YES YES YES YES B114LP NO NO YES YES NO NO NO °Bou depth contingent on base and wire size. Refer to National Electrical Code or local applicable codes for appropriate recommendations. Ordering Information Part No. Description 2151 Low-profile photoelectric detector. Must be mounted to one of the B100 Series or B400 Series bases listed in the Adapter Base Selection Guide. Accessories F110 Retrofit replacement flange for 8400 Series flanged bases, RA400Z Remote annunciator for 2 or 4 wire systems, 3-32V. Fits stan- dard single gang electrical boo. B401BH-2 Sounder base. Requires an external 24 VDC power supply. Mounts to 4" square electrical box )ih" minimum depth, 21Z" recommend- ed). SENS.RDR Hand-held sensitivity reader. SMK400 Surface mounting kit provides for entry of surface wiring con- duit. For use with 8401 or 6401R mounting bases only. EOLR-1 End of line relay for power supervision, 12/24 VDC systems. MO2-04-01 Test magnet. MO2-09-00 Test magnet with 32" telescoping handle. XR-28 Detector removal tool. Allows installation and/or removal of 100 Series detector heads from base in high ceiling installations when used with XP-4. System Sensor Sales and Service 21511 Low-profile photoelectric detector with thermal. Must be mounted to one of the 8100 Series or B400 Series bases listed in the Adapter Base Selection Guide. XP-4 Extension pole for XR-2B. Cornea in three 5 ft. sections. C58.227-01 Replacement dust cover for 100 Series smoke detectors. RMK400 Recessed mounting kit )13401 sold separately). System Sensor Headquarters System Sensor Canada System Sensor In China System Sensor - Far East System Sensor - India 3825 Ohio Avenue Ph: 905.812.0767 Ph: 86.29.8832.0119 Ph: 85.22.191.9003 Ph: 91.124.237.1770 x.2700 St. Charles, IL 60174 Fx: 905.812.0771 Fx: 86.29.8832.5119 Fx: 85.22.736.6580 Es: 91.124.237.3118 Ph: 800/SENSOR2 System Sensor Europe System Sensor in Singapore System Sensor - Australia System Sensor - Russia Es: 630/377.6495 Ph: 44.1403.891920 Ph: 65.6273.2230 Ph: 613.54.281.142 Ph: 70.95.937.7982 www.systemsensor.com Ex: 44.1403.891921 Fx: 65.6273.2610 Fx: 613.54.281.172 Fx: 70.95.937.7983 0 2006 System Sensor. The company reserves the right to change product specifications without notice. A05-0182-009.1/06•#1589 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION. OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7300-1653:109 Page 1 of 1 CATEGORY Misc. Devices/Control Unit Accessories LISTEE: System Sensor, Unincorporated Div of Honeywell Int'l Inc., 3825 Ohio Ave, St. Charles, IL 60174 Contact: Trish Linhart (630) 377-6580 ext. 1185 FAX (630) 377-7245 DESIGN: Models B401, B4016, B401 R, B401 BR, B401 BR-750, B401R-7502B, B4bB, 1340413T, 1340613, 13501, 1350113, 14506587-002, B5O1BH, 1350113HT, 13401131-1, 131101-P, 13110RLP, 1311ORLP750, 1311 1121-P, 13114LP, 13114LPBT, B116LPand B210LP detector bases. Refer to listee's data sheet for detailed product description and operational considerations. INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, product designation and UL label. APPROVAL: Listed as detector bases for use with separately listed compatible detectors. NOTE: Formerly 7300-1209:128 06-17-05 This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources. Date Issued: JUNE 4, 2008 Listing Expires June 30, 2009 Authorized By: BEN HO, Chief Fire Engineering Division INSTALLATION AND MAINTENANCE INSTRUCTIONS B ".STEM @ Plug-in Detector Base SENSOR For use with the following smoke detectors: In US: 1151, 2151 3825 Ohio Avenue In Canada: 1 St. Charles, Illinois 60174 A 1-800-SENSOR2, FAX: 630-377-6495 In Europe: 1151E, 2151E Specifications Base Diameter: 6.2 inches (157 mm) Base Height: 0.95 inches (24 mm) Weight: 0.3 lb. (130 g) Mounting: 4-inch square box with or without plaster ring. Min. Depth-1.5 inches 4-inch octagon box. Min. Depth-1.5 inches 3-1/2 inch octagon box. Mm. Depth-1.5 inches Operating Temperature Range: 0° to +49'C (32° to 120°F) Operating Humidity Range: 10% to 93% Relative Humidity Electrical Ratings - includes base and detector System Voltage: 24 VDC Maximum Ripple Voltage: 4 Volts peak to peak Start-up Capacitance: 0.02 hF Maximum Standby Ratings: 17 VDC Minimum; 32 VDC Maximum 120 jiA Maximum Alarm Ratings: 10 mA Minimum at 10.5 VDC; 62 mA Maximum at 32 VDC (If used, the RA400 remote lamp operates within specified detector alarm currents.) Maximum Alarm Impedance: 1050Q Minimum Alarm Impedance: 516Q Reset Voltage: 2.50 VDC Minimum Reset Time: 0.3 Seconds Maximum Start-up Time: 34.0 Seconds Maximum Before Installing General Description Please thoroughly read the System Sensor manual 156-407, The B110RLP plug-in detector base is used with System Guide for Proper Use of System Smoke Detectors, which pro- Sensor model 1151 and uSiA ionization detector heads and vides detailed information on detector spacing, placement, model 2151 and 2151A photoelectronic detector heads. The zoning, wiring, and special applications. Copies of this capability of plugging these detectors into a variety of spe- manual are available at no charge from System Sensor. (For cial bases makes them more versatile than equivalent installations in Canada, please refer to CAN4-5524, direct-wired models. Refer to the System Sensor catalog for Standard for the Installation of Fire Alarm Systems, and other available plug-in detector bases. CEC Part 1, Sec. 32.) NOTICE: This manual should be left with the owner/user of this equipment. IMPORTANT: The detector used with this base must be tested and maintained regularly following NFPA 72 require- ments. The detector used with this base should be cleaned at least once a year. This base is intended for use in 2-wire systems, with screw terminals provided for power, ground, and remote annun- ciator connections. The base also contains a resistor to pro- vide current limiting in the alarm state. D150-04-00 I 156-596•03R SCREWS (NOT SUPPLIED) SHORTINI SPRING DETECTOR BASE Mounting This detector base mounts directly to 3-1/2- inch and 4- inch octagon boxes, and 4-inch square boxes (with or with- out plaster rings). To mount, remove decorative ring by turning it in either direction to unhook the snaps, then sep- arate the ring from the base. Install the base to the box using the screws supplied with the junction box and the appropriate mounting slots in the base. Place decorative ring onto base, then turn in either direction until the ring snaps in place (see Figure 1). Figure 1. Mounting base to box: SNAP ON DECORATIVE RING Installation Guidelines All wiring must be installed in compliance with the National Electrical Code and the local codes having juris- diction. Proper wire gauges should be used. The conduc- tors used to connect smoke detectors to control panels and accessory devices should be color-coded to reduce the like- lihood of wiring errors. Improper connections can prevent a system from responding properly in the event of a fire. For signal wiring (the wiring between interconnected detectors), it is recommended that the wire be no smaller than 18 gauge (1.0 square mm). Wire sizes up to 12 gauge wire (2.5 square mm) may be used with the base. For best system performance, the power (+) and (-) loop wires should be twisted pair and installed in separate grounded conduit to protect the loop from extraneous electrical inter- ference. Smoke detectors and alarm system control panels have specifications for allowable loop resistance. Consult the control panel manufacturer's specifications for the total loop resistance allowed for the particular model control panel being used before wiring the detector loops. I ACAuTioN For system supervision - For terminals 2, 3, and 5 do not use looped wire under terminals. Break wire run to provide system supervision of connections. Wire connections are made by simply stripping insulation from the end of the wire, sliding the bare end of the wire under the clamping plate, and tightening the clamping plate screw. Use the strip gauge molded into the base for ease of wiring to terminals 1 through 5. System Sensor smoke detectors and mounting bases are marked with a compatibility identifier located as the last digit of a five digit code stamped on the back of the prod- uct. Connect detectors/mounting bases only to compatible control units as indicated in System Sensor's compatibility chart which contains a current list of UL listed control units and detector head/base combinations. A copy of this list is available from System Sensor upon request. 00 BOX (NOT SUPPLIED) ç ()00 , 01000 A78-1175-01 The zone wiring of the detector base should be checked before the detector heads are installed in them. To make this possible, this base contains a special spring-type short- ing jumper. After a detector base is properly wired and mounted on an electrical box, make sure that the jumper spring is in contact with the base of Terminal 3. This tem- porary connection shorts the negative-in and negative-out leads and permits the wiring of the loop to be checked for continuity. D150-04-00 2 156-596-03R PLASTIC LEVER BREAK TAB AT DOTTED LINE BY TWISTING TOWARD OF BASE. USE SMALL-BLADED SCREWDRIVER TO PUSH PLASTIC LEVER IN DIRECTION OF ARROW. 1J11 Figure 2. Typical wiring diagram for 2-wire detector systems: + REPEATER PANEL _J I Ui I z CL _j 0 F- z I 01 o Ui I cI E 0 L A78-1175-05 YL OPTIONAL FAULT TOLERANT WIRING + Once all the detector bases have been wired and mounted, and the loop wiring has been checked, the detector heads may be installed in the bases. The shorting spring in the base will disengage automatically when the detector head is removed from the base. DO NOT remove the shorting spring since it reengages as the detector head is turned into the base, completing the circuit. Tamper-resistance Feature NOTE: Do not use the tamper-resistance feature if the XR2 To make the detector tamper-resistant, use needle-nose pli- ers to break the smaller tab at the scribed line on the tamp- er- resistance tab. Figure 3A shows the location of this tab on the detector mounting bracket. To remove a detector from the bracket after it has been made tamper resistant, use a small screwdriver or other similar tool, to depress the tamper-resistance tab in the slot on the mounting bracket, and rotate the detector counter- clockwise (see Figure 3B). removal tool is to be used. NOTE: The decorative ring must be removed before the smoke detector can be detached from the base The tamper-resistant tab, in the detector mounting bracket, after the tamper-resistant capability is enabled. can make the detector tamper-resistant by making it neces- sary to use a small screwdriver or similar tool to detach the detector from the bracket. Figure 3L Activating the tamper-resistance feature: Figure 36. Removing detector head from base: A78-1175-03 D150-04••00 3 156-596••03R Please refer to insert for the Limitations of Fire Alarm Systems Three-Year Limited Warranty System Sensor warrants its enclosed smoke detector base to be free from defects in materials and workmanship under normal use and service for a period of three years from date of manufacture. System Sensor makes no other express warranty for this smoke detector base. No agent, represen- tative, dealer, or employee of the Company has the authority to increase or alter the obligations or limitations of this Warranty. The Company's obligation of this Warranty shall be limited to the repair or replacement of any part of the smoke detector base which is found to be defective in materials or workmanship under normal use and service during the three year period commencing with the date of manufacture. After phoning System Sensor's toll free number 800-SENSOR2 (736-7672) for a Return Authorization number, send defective units postage prepaid to: System Sensor, Repair Department, RA #, 3825 Ohio Avenue, St. D150-04-00 Charles, IL 60174. Please include a note describing the malfunction and suspected cause of failure. The Company shall not be obligated to repair or replace units which are found to be defective because of damage, unreasonable use, modifications, or alterations occurring after the date of manufacture. In no case shall the Company be liable for any consequen- tial or incidental damages for breach of this or any other Warranty, expressed or implied whatsoever, even if the loss or damage is caused by the Company's negligence or fault. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limita- tion or exclusion may not apply to you. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. I56-596-03R 2001 System Sensor CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7135-0569:122 Page 1 of 1 CATEGORY: Audible Devices LISTEE: Gentex Corporation, 10985 Chicago Dr., Zeeland Ml 49464 Contact: Keiffer Sestric (616) 392-7195 FAX (616) 392-4219 DESIGN: Model GEH24 horn and Models HS24-15, HS24-15/75, HS24-30, HS24-60, HS24-75, HS24-1 10, GEC24-1 5, GEC24-15/75, GEC24-30, GEC24-60, GEC24-75, GEC24-1 10, GEC-177, GCC24-C, GEC3-24 and WGEC1638-75 horn strobes. May be followed by - W (wall) and -W or -R (white or red) or -P plain. Models G24-C horn/strobe are ceiling mounted followed by -R (red), -W (white) or-P (plain). ReferTo listee's data sheet for additional product description and operational considerations. RATING: Electrical: 24 VDC Candela: 15cd, 15/75cd, 30cd, 60cd, 75cd, 110cd, 177cd. GCC24-C Ceiling: 15cd, 30cd, 75cd, 95cd 115cd (selectable) GEC3-24 Wall: 15cd, 30cd, 60cd, 75cd, 110cd (selectable) INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical ratings and UL label. APPROVAL: Listed as horn and horn/strobes for use with separately listed compatible fire alarm control units. For indoor use only. Model WGEC1638-75 is intended for outdoor use when used with Model GOE outdoor enclosure (CSFM Listing No. 7300-0569:124). Model WGECI638-75 is intended for private mode signaling use only and not approved for hearing impaired application. *The audible in Models GEH24, GEC24, GEC3-24, and WGEC1638 may produce distinctive tones including: mechanical, 2400Hz and chime tones in continuous and temporal 3 settings as well as a whoop tone in either a high or low dBA setting. *The audible in Model HS24 may produce a horn piezo frequency of 3100Hz. Model GCC24 may produce distinctive tones including mechanical and 2400Hz. Both models are capable of continuous and temporal 3 settings. Units can generate the distinctive three-pulse Temporal Pattern Fire Alarm Evacuation Signal (for total evacuation) in accordance with NFPA 72, 2002 Edition. Rev. 11-02-2007 This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources. Date Issued: JUNE 17, 2008 Listing Expires June 30, 2009 Authorized By: BEN HO, Chief Fire Engineering Division CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL -. FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM v LTSTING SERVICE LISTING No. 7125-0569:123 Page 1 of 1 CATEGORY: Fire Alarm Devices for the Hearing Impaired LISTEE: Gentex Corporation, 10985 Chicago Dr., Zeeland Ml 49464 Contact: Keiffer Sestric (616) 392-7195 FAX (616) 392-4219 DESIGN: Models ST24-15, ST24-15/75, ST24Q, ST24-60, ST24-75, ST24-110, GES24-15, GES24-15175, GES24-30, GES24-60, GES24-75, GES24-110, GES24-177, and GES3- 24 strobe lights; followed by suffix -W (wall mount), followed by -W or -R (white or red). Intended for indoor use and wall mount only. Model GCS-24 strobe light; followed by W or R (white or red color) and P (plain). For indoor use on wall or ceiling mount. *Model AVSM Sync Module intended for indoor use with Gentex synchronizable strobe lights. Refer to listee's data sheet for additional detailed product description and operational considerations. RATING: Candela: 1 5cd, 15cd & 75cd at 00 angle axis 30cd, 60cd, 75cd, ll0cd, 177cd. Model GCS24: Selectable 15cd, 30cd, 75cd, 95cd and 11 5c Model GES3-24: Selectable 15cd, 30cd, 60cd, 75cd and 110cd Electrical: 21-30 VDC *Model AVSM: 8-33 VDCNFWR Flash Rate: 60 flashes per minute INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical and candela ratings and UL label. APPROVAL: Listed as strobe lights suitable for the hearing impaired for use with separately listed compatible fire alarm control units. *Rev. 02-03-04 This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources. Date Issued: JUNE 17, 2008 Listing Expires June 30, 2009 Authorized By: BEN HO, Chief Fire Engineering Division L APPLICATIONS The Fike Low Frequency Evacuation Signals, manufactured by Gentex Corporation are a low profile strobe horn or horn/strobe combination that - - offer dependable audible and audible/visual alarms and the lowest current available The Fike Low Frequency Evacuation Signals horn offers a continuous or synch-able temporal three in 24001-1z and mechanical tone, a chime as well as a whoop tone. All tones are easy for the professional to change in the field by using Strobe Horn/Strobe Horn switches. Signals are shipped from the factory on the temporal low frequency mode and come standard with a rugged cast metal mounting plate. The Fike Low Frequency Evacuation Signals have a minimal operation current and a minimum flash rate of 1Hz regardless of input voltage. Another first for the Fike Low Frequency Evacuation Signals is the SuperSlide to test supervision. Also included is a locking mechanism which secures the product to the bracket without any screws showing. These durable appliances are UL 464, UL 1971, UL 1638 listed for use with fire protective systems and are warranted for three years from date of purchase. STANDARD FEATURES/SPECIFICATIONS APPROVALS Prewire Entire System, Then Install Synchronize Strobe and/or Horn by Americans with Disabilities Act Your Signals Using the AVS Series Control (ADA 4.28.3) Ease of Supervision Testing Module (see Gentex Technical BFP (City of Chicago) (SuperSlide) Bulletin 015) BS+A/MEA #285-91-E - XV Lower Installation and Operating Silence Horn While Strobes Remain CSFM 7135-0569:122 (Horn, Costs Flashing Horn Strobe); 7125-0569:123 Input Terminals 12 to 18 AWG . Rugged Die Cast Metal Mounting (Strobe) Switch Selection for High or Low Bracket FM Approved dBA 15/75, 75, 110 and 177 Candela NFPA 72 Switch for Chime, Whoop, Strobe Meets or Exceeds UL ULC Dual Listed 464, Mechanical and 2400Hz 'Tone ADA 4.28.3 Requirements 1971, 1638 Switch for Continuous or Temporal True Evacuation Tone 3 (not available on whoop tone) • Wide Voltage Range 16-33 VDC or Tamperproof Re-entrant Grill FWR Surface Mount with the GSB • Widest Range of Candela Available (Surface Mount Box) Available in Red or Off-White AVAILABLE MODELS 12 and 24 VDC Low Profile Evacuation Horn, Wall or Ceiling Mount Fike P/N Manf. P/N Nominal Voltage dBA @ lOFt. Color 20-123-142 904-1239-002 12 VDC 100 Red 20-123-143 904-1241-002 12 VDC 100 White 20-123-27 904-1205-002 24 VDC 100 Red 20-123-28 904-1207-002 24 VDC .100 White 704 S. 10th Street P.O. Box 610 Blue Springs, Missouri 64013-0610 U.S.A. (816) 229-3405 (816) 229-0314 www.flke.com 12 and 24 VDC Low Profile Evacuation Horn, Wall or Ceiling Mount Fike P/N Manf. P/N Strobe Candela Color Operating Strobe Current @ 24VDC 20-124-15WR 904-1165-002 15 Red 55mA 20-124-15\VW 904-1185-002 15 White 55mA 20-124-30WR 904-1169-002 30 Red 631nA 20-124-30WW 904-1189-002 30 White 63mA 20-124-60WR 904-1173-002 60 Red 881nA 20-124-60W'X' 904-1193-002 60 White 88mA 20-124-75WR 904-1175-002 75 Red 112mA 20-124-75WW 904-1195-002 75 White 112mA 20-124-11OWR 904-1179-002 110 Red 136mA 20-124-11OWW 904-1199-002 110 White 136mA 20-123-23 904-1183-002 177 Red 1861uA 20-123-24 904-1203-002 177 White 186m-A, 20-124-15-75WR 904-1167-002 15 (UL 1971) 75 (UL 1638) Red 63mA 20-124-15-75WW 904-1187-002 15 (UL 1971) . (UL 1638) White 63mA 24 VDC Low Profile Evacuation Horn/Strobe, Wall Mount Fike P/N Manf. P/N Strobe Candela Operating Strobe Current @ 24VDC Horn Current Color Anechoic Room dBA @ lOFt. 20-123-15WR 904-1125-002 15 55mA 21rnA Red 100 20-123-15WW 904-1145-002 15 55mA 21mA White 100 20-123-30WR 904-1129-002 30 63mA 21mA Red 100 20-123-30WW 904-1149-002 30 63mA 21rnA White 100 20-123-60WR 904-1133-002 60 88mA 21rnA Red 100 20-123-60WW 904-1153-002 60 88mA 21mA White 100 20-123-75WR 904-1135-002 75 1121nA 21rnA Red 100 20-i23-75W 904-1155-002 75 112mA 21mA White 100 20-123-110WR 904-1139-002 110 136mA 21mA Red 100 20-123-11OWW 904-1159-002 110 136mA 21niA White 100 20-123-42 904-1143-002 177 186mA 21rnA Red 100 20-123-43 904-1163-002 177 186iuA 21iuA White 100 20-123-15- 75WR 904-1127- 002 15 (UL 1971) 75 (UL 1638) 63mA 21mA Red 100 20-123-15- 75WW 904-1147- 002 15 (UL 1971) 75 (UL 1638) 631nA 21mA White 100 NOTES: The Fike Low Frequencji Evacuation Signals are not listed for outdoor use. Operating temperature: 320to 120°F (00 to 490 Q. For nominal and peak current across UL regulated voltage range forfiltered DC power and uifiltered Full Uwe Rectified (1 WR) powel; see installation manual. Fike does not recommend using a coded or pulsing signaling circuit with anji of our strobe products (fee Gentex technical bulletin number 014). Dimensions 2.5 4.5" -..— -. _J Mounting SuperSlide Die Cast Metal Mounting Plate: Mounts to single gang, double gang 4" square boxes or GSB box. Switch Locations Removing Bezel SWITCH POSITION 3 4 5 Mechanical-Temp. ON ON ON Mechacical-Cont. OFF ON ON -h-Temp ON OFF ON Hi-Cant. OFF OFF ON Chime-Temp. ON ON OFF Chime-Cent OFF ON OFF h°4tcep ON OFF OFF h'aheap OFF OFF OFF Switch Position 6 ON > HIGH dB OFF> LOW dB Switch positions I and 2 In the off position to select isolated horn and strobe I power inputs. I.IuI.IuIuI.I IuIRIIII I.I.I.I.I.I. Grip both sides of bezel and pull in a downward and outward motion. Conventional Horn/Strobe and Horn Strobe Series Wiring Diagrams UL Listed ULListod I I Control anfroI I abnw I I I I Panel Panel 1-3- I I a+ a+ a. 14+ H- I I SU)QfVI59d Supervised III$ iI I I I Signal Circuit Signal Circuit _______ I 'ENDIDFLM t5TOR ME rsriiI 11111 IIIIII 11111 Elm Wiring Diagram: Fike Low Frequency Evacuation Signals with AVS Series Synchronization Module F.A.C.P RESISTs/i FOR ENDOFUNE + - ------ TO NEXT SIGNAL CIRCUIT RIN ----------------------------------- NOTIFICATION ALARMCIRCUIT sOY. TON SIGNAL TO NOTIFICATION ALARM CIRCUIT REMOVEJUMPER FORINDEPENDENT SYNCHRONIZED STROBE PL AUDIBLE SIGNALC>i AND ORN OPERATION CIRCUIT ~EE-.UT.'RL1-& 8 ROW` ONLY. TO ELIMINATE IN EED FOR 0 L EAVE JUMPER PLACE ON FOO 5-0 HORN INPUT N AVSM LAVE UNITS UNL EINSS SEPARATE AND OPERATE SIGNAL IS CONTROL OVER HORN CKT /I IN UNISON MODE IS REQUIRED. ENS SF LINE I VISIBLE SIGNAL SL'+ I I RESISTOR FOR I OI.ASS S CIRCUIT I MR/il/i ONLY ENS OF LIME RESISTOR FOR C LOSS 0 WIRING ONLY. NOTE: See Gentex Technical Bulletin 0 l5forproper synchronLation module/or application. HornRatingsOver Input VoltageRange of 16-33V Horn Mode dBA @ lOFt. Per UL464 HIGH dB dBA @ lOFt. Per UL464 LOW dB DC(mA) FWR(mA) 16v 24v 33v lflv 24v 33v 16v 24v 33v 16v 24v 33v Temp2 2400Hz 78 83 84 71* 75 77 13 19 24 27 37 43 Temp3Mechanical 76 81 82 70* 73 76 11 16 22 23 33 40 Temp3Chime 70* 71* 71* 66* 68, 70* 9 12 15 19 24 29 Continuous 24001-lz 81 86 87 . 74* 78 80 14 21 28 21 42 48 Continuous Mechanical 80 84 85 72* j 76 j 78 j 13 18 j 25 j 27 j 37 44 Continuous Chime 70* 71* 73* 66* 68* 70* 10 12 15 19 24 30 Whoop 82 83 83 69* 72 75 43 51 56 51 58 62 Opera/log the bore in this mode UI this rslIcge will ross/.I in not meetle5 the smsomcm [IL reverberant sm/sod level reqou red [orpesbloc scot/c fire Jlro/ec/eoe Sense. These .e1/ons are acceptable oii/yforpiva/e mode fire a/area site. Use the hihh dBA set/on,g Jon posh/ic mode app localeon (em! applicable nbc/I °5kt I/se chime tone. The chime lone if o1ILa)speoscltc rest/c). NOTES: The soomd oil/post for the tempera/3 tone is rated loser since the lime tile horn scoff is alOIriged into the siiiiid Os/tost ratisob. lr'/,ik the horn oJprodoaon1 a tone on the temporal-3 mode its ssoind pressure is the same cii the ro,,Is5000a' soode. ARCHITECT AND ENGINEERING SPECIFICATIONS The audible and/or visible signal shall be Gentex or approved equal and shall be listed by Underwriters Laboratories inc. per [IL 1971, [IL 1638 and/or [IL 464. The notification appliance shall also be listed with the California State Fire Marshall (CSFM) and the Bureau of Standards and Appeals (NY. The notification appliance (combination audible/visible and audible units only) shall produce a peak sound output of 100d1L\ or greater as measured in an ancchoic chamber. The signaling appliance shall also have the capability to silence the audible signal while leaving the visible signal energized with the use of a single pair of power wires. Additionally,the user shall be able to select either continuous or temporal tone output with the temporal signal having the ability to be synchronized. The audible/ visible and visible signaling appliance shall also maintain a minimum flash rate of ll-lz or greater regardless of power input voltage. The appliance shall also he capable of meeting the candela requirements of the ADA (75Cd) for the combination listed ([IL 1971/IlL 1638) listed models. The appliance shall have an operating current of 63naA or less at 24 VDC for the 15/75Cd for the strobe circuit. The appliance shall be polarized to allow for electrical supervision of the system \unng. The unit shall be provided with a mounting bracket with terminals with harriers for input/output wiring and be able to mount to a single gang or double gang box or double workbox without the use of an adapter plate. The unit shall have an input voltage range of 16-33 volts with either direct current of full wave rectified power. The appliance shall be capable of test supervision without disconnecting wires. Also the appliance shall be capable of mounting to a surface back box. F1 ke Copyright © Fike Corporation All Rights Reserved. OP POP Al ON Form No. P.1.25.01 May, 2004 Specifications are subject to change without notice. HFC-125 CLEAN AGENT APPLICATION/DESCRIPTION HFC-125 fire suppression agent is an environmentally acceptable replacement for I-Talon 1301. HFC-125 has a zero ozone depleting potential, a low global warming potential, and a short atmospheric lifetime. It is particularly useful where an environmentally acceptable agent is essential, where clean-up of other media presents a problem, where weight versus suppression potential is a factor, where an electrically non-conductive medium is needed, and where people compatibility is an overriding factor. HFC-125 can be used to protect a wide range of applications from sensitive electrical equipment to industrial applications. Consult the current NFPA Standard 2001 and/or ISO 14520 for specific applications. HFC-125 fire suppression agent is used with Fike's total flooding systems. HFC-125 is an odorless, colorless, liquefied compressed gas. (See Physical Properties Table for additional information). It is stored as a liquid and dispensed into the hazard as a colorless, electrically non-conductive vapor that is clear and does not obscure vision. It leaves no residue and has acceptable toxicity for use in occupied spaces at design concentration. HFC-125 extinguishes a fire by a combination of chemical and physical mechanisms. HFC-125 does not displace oxygen and therefore is safe for use in occupied spaces without fear of oxygen deprivation. PERFORMANCE -- HFC-125 is an effective fire extinguishing agent that can be used on many types of fires. It is effective for many surface fires and most solid combustible materials. On a weight-of-agent basis, HFC-125 is a very effective gaseous extinguishing agent. The minimum design concentration for normal Class A combustibles protecting a total flood application is 8%, in accordance with NFPA 2001 and 8.7%, in accordance with ISO. SPECIFICATION HFC-125 is of high organic purity and essentially residue-free, meeting the following quality specifications: Purity, % by weight: 99.0 Mm. Moisture, ppm by weight: 10 Max. Acidity, ppm by weight, expressed as HC1: 0.1 Max. Residue, % by volume: 0.01 Max. TOXICITY The toxicology of HFC-125 compares favorably with that of other suppression agents. The LC50 of HFC-125 is greater than 700,000 ppm. HFC-125 has been evaluated for cardiac sensitization via test protocols approved by the United States Environmental Protection Agency. Test results show that cardiac tolerance to HFC-125 is much higher than that of Halon 1301 and will be acceptable for safe use in occupied space protection. HFC-125 will decompose to form halogen acids when exposed to open flames. The formation of these acids is minimized by using Fike early warning detection systems and proper system installation. When properly applied and installed, the generation of these by-products by 14FC-125 is minimal. APPROVALS HFC-125 complies with NFPA Standard 2001 - current edition. Fike ECARO-25 systems are Factory Mutual approved and UL listed for Clean Agent Fire Suppression Systems. UL Listed - Ex 4623 FM Approved - 3014476 Form No. C.1.12.01-2 704 S. 10th Street P.O. Box 610 Blue Springs, Missouri 64013-0610 U.S.A. . (816) 229-3405 . (816) 229-4615 www.fike.com PHYSICAL PROPERTIES Chemical Name/Formula Pentafluoroethane / CHF2CF3 CAS Number 354-33-6 European Classification Number EC-No.: 206-5578 Molecular Weight 120.02 Vapor Density @25°C (77°F) and atm, kg/m3 (lb/ft3) 4.982 M3 (0.3111 Vapor Pressure, Saturated @ 25°C (777), bar (psia) 13 bar (200.4) Boiling Point, 1 atm, °C (°F) -48.14 (-54.7) Freezing Point, °C (°F) -103(-153) Solubility in Water in FE-25 @ 25°C (77°F), ppm 700 Critical Temperature, 'C (*F) 66.25 (151 .25) Critical Pressure, bar (psia) 36 (526.6) Critical Volume, cc/mole 210 Critical Density, kg/M3 (lb/ft3) 571.9 (35.70) Specific Heat, Liquid (CP) @ 25°C (77°F), KJ/Kg- °C (Btu/lb°F) 1.37 (0.327) Specific Heat, Vapor (CP) @25°C (77°F) KJ/Kg- °C (Btu/lb°F) and 1 atm 0.809 (0.193) Heat of Vaporization @ Boiling Point KJ/Kg (Btu/lb) 164.4 (70.7) Thermal Conductivity, Liquid @ 25°C (77°17), W/m- °C (Btu/hr-ft°F) 0.0652 (0.0377) Thermal Conductivity, Vapor @ 25°C (77°F), Wlrn- °C (Btu/hr-ft°F) 0.0166 (0.0096) Viscosity, Liquid @25°C (77°F), cP (lb/ft-hr) 0.137 Viscosity, Vapor @ 25°C (77°F), cP (lb/ft-hr) 0.013 Ozone Depletion Potential 0 Global Warming Potential (based on a 100-yr horizon relative to CO2) 2800 Estimated Atmospheric Lifetime* 32.6 years Inhalation Exposure Limit (AEL-8 and 12hr. TWA), ppm** 1000 * SecondAssessment Report (1995)- Intergovernmental Panel on Climate change (IPCC). ** The acceptable exposure limit (AEL) is the 8-hr time weighted average (TWA) workplace exposure limit established /y DuPont. Copyright © Fike Corporation All Rights Reserved. Form No. C.112.01-2 February, 2008 Specifications are subject to change without notice. ECARO-25Th' AGENT STORAGE CONTAINERS DESCRIPTION Fike Series 70 Clean Agent Containers are used in fire extinguishing systems to store the Clean Agent until a fire develops and the agent must be released. The Clean Agent is retained in the container by a valve assembly which contains a fast-acting rupture disc. The disc will he ruptured, and the Clean Agent released, through the operation of an actuator by an electric signal that is automatically or manually controlled. The valve is available in three sizes: 1" (25mm), 2 1/2" (65mm) and 3" (80mm). The 1" (25mm) valve is used on the 20 (8), 35 (15), 60 (27), and 100 pound (44 L) containers; the 2 1/2" (65mm) valve is used on the 1251 (51 L) and 215i pound (90 L) containers; the 3" (80mm) valve is used on the 215 (87), 375 (153), 650 (267) and 1000 pound (423 L) containers. After a discharge, the valve is field reconditioned by simply replacing three components. Fike Series 70 Clean Agent Containers have passed extensive testing by Factory Mutual and Underwriters Laboratory and are used in installations where 8 to 836 pounds (3.5 to 379.5 kg) of HFC-125 agent is required. To eliminate the need for multiple containers, or using more Clean Agent than necessary, these containers can be filled in 1 pound (0.5 kg) increments to their maximum capacity. Each container for ECARO-25 Clean Agent Systems is super pressurized with dry nitrogen to 360 psig (25 bar), at 70° F (21° C), to provide a quick and effective discharge in 10 seconds or less. Fike Series 70 Clean Agent Containers are supplied with a pressure gauge that permits a quick, visual, inspection of container pressure. Optional items include a Liquid Level Indicator, and a Low Pressure Supervisory Switch. The Liquid Level Indicator provides the convenience of determining the container's agent weight without removing it from its installed location. The Low Pressure Supervisory Switch provides constant monitoring of the container's internal pressure. In the event of a decrease in container internal pressure from 360 psig to 288 psig (24.8 bar to 18.8 bar), the Supervisory Switch normally opened/closed contacts will close/open. This will cause a supervisory trouble alarm at the system control panel. Fike Series 70 Clean Agent Containers are available for installation in the upright, inverted or horizontal positions, depending upon the user's particular needs and the type and size container specified. The, mounting location of the container is quite flexible. It can be mounted at the exact point of discharge or at a remote location by adding distribution piping from the container to the nozzle system. (Refer to the Fike Design, Installation and Maintenance Manual - P/N 06-285). The operating temperature range is +32° to +120'F (0° to 49.0°C) in any installation. If the Clean Agent reaches an internal temperature range of 130° to 150°F 49.90 to 65.5°), it will create a sufficient internal pressure to burst the rupture disc and release the Clean Agent through the piping network. APPROVALS UL Listed - Ex 4623 FM Approved .. OY4ABAF (HFC-227ca) Form No. C.1.41.01-4 I 704 S. 10th Street P.O. Box 610 Blue Springs, Missouri 64013-0610 U.S.A. . () 229-3405 . (816) 229-4615 www.fike.com RELIABILITY Fike Series 70 Clean Agent Containers are manufactured in strict accordance with Department of Transportation (DOT.) regulations. The Fike Series 70 Clean Agent Containers have successfully passed testing by Factory Mutual and Underwriters Laboratories, Inc. Before leaving the factory, each container must pass extensive leakage testing, and pressure testing to 1000 psig (69 bar) The containers are constructed from carbon steel alloys and painted with a durable, baked enamel finish. INSTALLATION Fike Series 70 Clean Agent Containers are supplied with a mounting bracket that is designed to provide the most effective and versatile installation for that particular container. The 20 and 35 pound (8 and 15 L) container brackets employ two U-bolts for securing the container to the bracket. The 60 pound (27 L) container is secured using two quick connecting, over-center handle clamps. The 125i and 215i pound (51 and 90 L) containers utilize an "L" shaped bracket for direct wall mounting or, with an optional floor mounting kit, can be mounted on a floor in the "valve down" position. The 100 (44) and 215 (87) through 1000 pound (423 L) containers are supplied with one U-shaped mounting strap for mounting to a wall or other secure surface. CLEAN AGENT STORAGE CONTAINER DATA - U.S. STANDARD Fike P/N Size (lbs) Valve (in) Empty Wt (Ibs) HFC-1 25 Agent Fill Range_(lbs) Valve Position DOT. Regulation 70-098 20 1 21 8-16 Horizontal or Upright 413500 70-089 1 35 1 32 14-30 Horizontal or Upright 413500 70-152 60 1 44 25-54 Horizontal or Upright 4BW500 70-153 100 1 61 39-87 Upright 4BW500 70-041 125i 21/2 180 46-101 Inverted 4BA500 70-077 215i 21/2 225 80-178 Inverted 4BA500 70-154 215 3 150 78-173 Upright 4BW500 70-155 375 3 218 136-302 Upright 4BW500 70-156 650 3 350 236-528 Upright 4BW500 70-157 1000 3 515 374-836 Upright 4BW500 LET os$ D LEV cu1LT CLEAN AGENT STORAGE CONTAINER DATA - METRIC Size (L) Valve (MM) Empty Wt HFC-1 25 Agent Fill Range (KG) Valve Position R DOT. Regulation 70-098 8 25 10 3.5-7.5 Horizontal or Upright 46500 70-089 1 15 25 15 6.5-13.5 Horizontal or Upright 413500 70-152 27 25 20 11.5-24.5 Horizontal or Upright 4BW500 70-153 44 25 28 18.0-39.0 Upright 4BW500 70-041 51 65 82 21.0-46.0 Inverted 4BA500 70-077 90 65 102 36.5-81.0 Inverted 4BA500 70-154 87 80 68 35.5-78.5 Upright 4BW500 70-155 153 80 99 61.5-137.0 Upright 4BW500 70-156 267 80 159 107.0-239.5 Upright 4BW500 70-157 423 80 234 169.5-379.5 Upright 4BW500 CLEAN AGENT STORAGE CONTAINER DIMENSIONS 20 - IOOLB (8 to 44L) Container 125i and 215i LB (51 to 90L) Container 215 - 1000LB (87-423L) Container (LLi on 100LB (44L) only U.S. Sizes and Dimensions Size-LB 20 35 60 100 125i 215i 215 375 650 1000 A(in) 7.25 7.25 10.75 10.75 20.00 24.00 20.00 20.00 24.00 24.00 B (in) 21.50 32.50 28.00 38.75 20.25 23.75 28.87 42.50 48.75 70.00 Metric Sizes and Dimensions Size-L 8 15 27 44 51 90 87 153 267 423 A(mm) 184 184 273 273 508 610 508 508 610 610 B(mm) 546 826 711 984 515 605 733 1080 1237 1778 ARCHITECT AND ENGINEERING SPECIFICATIONS The Clean Agent shall be stored in Fike Series 70 Clean Agent Storage Containers. The containers shall be capable of being filled, in one-pound (0.5kg) increments, to their listed maximum capacity. The Clean Agent container shall be activated by a signal from the control panel which is processed by the Agent Release Module. This module shall store the power requited to operate the actuator. The valve shall contain a scored, non-fragmenting, rupture disc to provide an immediate, total discharge of all the agent. HFC-125 Clean Agent is stored in the container as a liquid, having a natural vapor pressure of 200 psig at 77°F (13 barg at 25°C). To aid in discharge, the container shall be super-pressurized to 360 psig at 70°F (25 bar at 21°C) with dry nitrogen. Agent discharge shall be completed in 10 seconds or less. Clean Agent Storage Containers shall be actuated by an electrical signal that is automatically, or manually controlled. Normal operating temperature shall be +32° to +120°F (0° to 49°C) in any installation. Clean Agent Storage Containers shall be equipped with a pressure gauge to display internal pressure. This gauge shall be an integral part of the container and color coded for fast referencing of pressure readings. A Low Pressure Supervisory Switch shall he made available, as an option. A decrease in internal container pressure from 360 to 288 psig (24.8 to 18.8 bar) shall cause the normally opened/closed Supervisory Switch contacts to close/open, indicating a trouble or supervisory condition, at the control panel. Clean Agent Storage Containers shall he fastened to a wall, or other secure surface, using a mounting bracket that is designed for the most effective and versatile installation of each container. Copyright © Fike Corporation All Rights Reserved. Form No. C.1 .41.01-4 February, 2008 Specifications are subject to change without notice. INDICATOR TAPE READ HERE APPROVALS UL Listed - Ex 4623 FM Approved - 3014476 BOSS UNIT STEM I, _\ ,-LIQUID LE MAGNETIC FLOAT / ECARO25TM LIQUID LEVEL INDICATOR DESCRIPTION The Fike 70-1353 series Liquid Level Indicator is a - simple manually operated device which provides a means to determine the Clean Agent liquid level in vertically mounted agent storage containers. Once the - liquid level is determined, it can then be converted into pounds (kilograms) of Clean Agent present in the agent storage container. EcARO-25 Liquid Level Indicator OPERATION A magnet equipped float moves with the liquid level along the unit stem. Level readout is obtained by simply removing the protective cap and pulling out a calibrated tape until magnetic interlock with the float is felt. With the tape in this position, the reading is obtained at the point where the tape emerges from the unit housing. When the liquid level is determined, the reading is then located on a chart and the corresponding Clean Agent weight is read. Accurate readings can be obtained over a +400 to +90°F (+4.40 to +32.2°C) temperature range. FEATURES Reduced maintenance time - the weight of the agent in storage containers can be determined in a fraction of the time it would take to remove and weigh them. Continuous fire protection - use of the liquid level indicator does not require shutting down the Clean Agent System, thus affording uninterrupted fire protection. Field installation capability - the indicator can easily be installed in the field using a single wrench, as long as the container is empty and is equipped with a mounting boss. Compact - when not in use, the unit requires no more space than that required by the container. Flexibility - the flexible tape design allows the unit to be used in tight spaces that would otherwise hinder the use of a rigid indicator "stick". Availability - units are available for Fike container sizes of 100 lb. (44 liter) through 1000 lb. (423 liter) in both the modular and central storage type designs. CONSTRUCTION The Fike 70-1353 series Liquid Level Indicator housing and stem assembly is constructed of brass. The flexible indicator tape is constructed of steel with a yellow mylar coating. The indicator tape is calibrated in inches and centimeters. The unit housing provides straight mounting threads with a static 0-ring seal. The float is constructed of a special ECCO material for high pressure service. The cellular construction of the ECCO material allows the float to be solid and is not susceptible to water-logging, as hollow floats are if they develop a leak. The unit is provided with a plastic protective cap. Form No. C.1.40.01-2 704 S. 10th Street P.O. Box 610 Blue Springs, Missouri 64013-0610 U.S.A. . (816) 229-3405 (816) 229-4615 www.fike.com AVAILABLE MODELS Indicator P/N Dimension "L" Fits Container Size Container PIN 70-1353-27 27" (686 mm) 100 lb. (44 liter) 70-153 70-1353-11 11" (279 mm) 125i lb (51 liter) 70-041 70-1353-18 18" (508 mm) 215 lb (87 liter) 70-154/S70-154 70-1353-15 15" (381 mm) 215i lb (90 liter) 70-077 70-1353-27 27" (686 mm) 375 lb (153 liter) 70-155/S70-155 70-1353-38 38" (965 mm) 1 650 lb (267 liter) 70-156/S70-156 70-1353-49 49" (1244 mm) 1000 lb (423 liter) 70-157/S70-157 Measuring Tape H Float Inspection k—C Tag Cap ARCHITECT AND ENGINEERING SPECIFICATIONS Agent storage containers of 100 lb. (44 liter) capacity or more shall be provided with a reliable means, other than weighing, of determining the agent weight within the storage container during normal routine service. The device used shall be a Fike 70-1353-xx series Liquid Level Indicator and shall not require any additional space when the container is installed. Use of the indicator shall not require the Clean Agent System to be shut down thus allowing uninterrupted fire protection during service intervals. Level indicators which are not factory installed shall be capable of being retrofitted in the field, with a single standard wrench, when the container is removed for recharge. The level indicator tape shall be flexible to allow use in confined spaces. The unit housing shall be constructed of brass with straight mounting threads and a static 0-ring seal. The float shall be of solid construction to eliminate the possibility of water logging to which hollow floats are susceptible. The float shall he equipped with a magnet which provides a positive feel when the magnetic interlock is reached between the float and indicating tape. When the level reading is obtained, the agent weight can be determined through the use of the chart or graph found in the Liquid Level Indicator Manual (P/N: 06-289). Accurate readings shall be capable of being obtained over a +400 to 90°F (+4.40 to +32.2('C) temperature range. iAm Copyright © Fike Corporation All Rights Reserved. CO Form No. C.1.40.01-2 February, 2005 Specifications are subject to change without notice ECARO-25TM ENGINEERED NOZZLES DESCRIPTION The function of the ECARO-25 Engineered Discharge Nozzle, in a fire extinguishing system, is to distribute the clean agent in a uniform, pre-determined pattern and concentration. The nozzles are designed to complete the discharge of clean agent when installed within the design limitations of the EC kRO 25 Design Manual (P/N 06 238 06 239 01 06-285 and the EC \RO 25 Flow Calculation computer program) Fike Engineered Discharge Nozzles are available in sizes- of 3/8",1/2"',3/4 1 1 1/4",11/2 and 2 (10 15 20 25 32 40 0mm). Each nozzle is available in 180 and 360 degree discharge patterns. The Discharge Nozzle size refers to the size of Schedule 40 or 80 steel pipe to which it can be connected. The nozzle discharge orifices are drilled perpendicular to the center line of the threads and discharge on a horizontal axis. Nozzle orifices are available in a wide range of sizes to provide accurate clean agent flow results. All nozzles have been tested for their ability to discharge the clean agent under extreme conditions. Nozzle orifice drilling must he done at the Fike factory only after 'As-Built" calculations of the installed piping system(s) have been performed, using the ECARO-25 Flow Calculation computer program. The Fike Discharge Nozzle used shall be Factory Mutual (FM) approved and Underwriters Laboratory (UL) listed. ARCHITECT SPECIFICATIONS The nozzle used to disperse Clean Agent shall be a Fike Series 80 nozzle. The nozzle shall be available in 3/8", 1/2", 3/4", 1", 1 1/4", 1 1/2", 2" (10, 15, 20, 25, 32, 40, 50mm). Each size shall be available in both 180 and 360 degree dispersion patterns. The nozzle used shall have pipe threads that correspond to the nozzle size. All nozzles shall have an orifice size determined by the FM approved and UL listed ECARO-25 Flow Calculation Program. All nozzle orifice drilling shall be performed by the manufacturer. Form No. C.2.24.01-3 704 S. 10th Street P.O. Box 610 Blue Springs, Missouri 64013-0610 U.S.A. . (816) 229-3405 . (816) 229-4615 www.fike.com [I 1800 NOZZLE 360° NOZZLE 3/8" (10mm) Nozzle Area Coverage Nozzle Type Ceiling Height Dimensions Range 1800 22'- 9" 1.0-16.0 (6.93.m) (0.3-4.9 m) 360° 14'-9" 1.0-16.0 (4.5 m) (0.3 - 4.9 m) ORDERING FORMAT "BSP" THREAD 84-015 10mm x 360° Nozzle 84-016 15mm x 360° Nozzle 84-017 20mm x 360° Nozzle 84-018 25mm x 360° Nozzle 84-019 25mm x 360° Nozzle 84-020 32mm x 360° Nozzle 84-021 50mm x 360° Nozzle 84-022 10mm x 180° Nozzle 84-023 15mm x 180° Nozzle 84-024 20mm x 180° Nozzle 84-025 25mm x 1800 Nozzle 84-026 32mm x 180° Nozzle 84-027 40mm x 180° Nozzle 84-028 50mm x 180° Nozzle 1/2" -2" (150 50mm) Nozzle Area Coverage Nozzle Type Ceiling Height Dimensions Range 180° 45-8" 1.0-16.0 (13.92 m) (0.3-4.9 m) 3601 29'- 8" 1.0-16.0 (9.04 m) (0.3 ORDERING FORMAT "NPT" THREAD 80-036 3/8" x 360° Nozzle 80-037 1/2" x 360° Nozzle 80-038 3/4" x 360° Nozzle 80-039 x 360° Nozzle 80-040 1 1/4" x 360° Nozzle 80-041 1 1/2" x 360° Nozzle 80-042 x 360° Nozzle 80-044 3/8" x 1800 Nozzle 80-045 1/2" x 180° Nozzle 80-046 314" x 180° Nozzle 80-047 x 1800 Nozzle 80-048 1 1 1/4" x 180° Nozzle 80-049 1 1/2" x 180° Nozzle 80-050 x 180° Nozzle F I ke Copyright© Fike Corporation All Rights Reserved. Form No. C.2.24.01-3 February, 2008 Specifications are subject to change without notice. GAS CARTRIDGE ACTUATOR DESCRIPTION The Gas Cartridge Actuator (GCA), Fike P/N 70-1651, provides the necessary pressure to fully open all Fike's Clean Agent containers utilizing a Fike fast acting rupture disc assembly. The GCJ\ consists of a stainless steel body containing two sets of bridge wires and a charge of smokeless powder. Operation of the GCA occurs when an electric current is sent through the bridge wires causing the smokeless powder to ignite. This generates the necessary pressure to open the rupture disc and discharge the agent in the Clean Agent container. The GCA is not an explosive device and cannot he used as a detonator. Operating time for the GCA is 10 milliseconds. Operating temperature range for the GCA is +32° to +130°F. (0° to +54.4°C) for HFC-227ea systems. For ECARO-25 systems, the maximum operating temperature is 120°F (490C). The GCA is designed to operate in all Fike Clean Agent system containers with 1" and 2 1/2" valves and also containers with 3" valves with single disc packs. This device is designed to operate by two methods of actuation: Electrical input from a Fike Control Unit or Interface Firing Module (IFM) and through an Agent Release Module ARM). Input from an (optional) independent Fike Manual Actuator. Installation The GCA has two sets of threads; the 3/8-24 UNF-20 thread is used to install the GCA in either I or 2 1/2' (25 or 65mm) valved containers and the 7/16-20 UNF-24 thread is used to install the GCA in the 3" (80mm) valved containers, without modification to the valve assemblies. It should be noted that for retrofit systems, the junction box for the ARM/GCA may need to be longer and/or larger than was required for the ARIvl/detonator device. Shelf Life The GCA is a sealed device utilizing a glass seal and epoxy plug on the wire end and a mylar seal on the discharge end. This extends the actuator's continuous service and shelf life to 10 years before it requires replacement. Shipping Classification The GCA will not detonate any explosive materials or products. It has a U.S. Department of Transportation classification of: - Class: 1.4 - Compatibility Group: "S" - Shipping Number: Ui'0323 This classification allows this device to be shipped on any type of carrier (excluding ocean containers) such as commercial airlines, as well as all forms of land carriers without special handling permits and/or licensing. Gas Cartridge Actuator APPROVALS UL Listed - Ex 4623 FM Approved: HFC-227EA: 0Y4A8.AF EC.ARO25Tat: 3014476 Form No. 0.1.26.01-2 704 S. 10th Street P.O. Box 610 Blue Springs, Missouri 64013-0610 U.S.A. (816) 229-3405 (816) 229-4615 www.fike.com ECARO-25 Flow Calculation Software Fike Corporation F1 OR e P k ORATION ECARD(I r' ECARO-25 Flow Calculation Software Version 3.30.0000 Copyright © 2002-2005 Fike Corporation UL Ex4623, FM 3014476 Licensed to Glen Upole, Facilities Protection Systems Results Printed on 2/12/2009 PROJECT INFORMATION Project Name: JiTTERBUG Project Designer: C1684 Project Location: Project Account: Project Description: SYSTEM 'TA" Project Filename: N:\l-Engineering Projects\C160 1-C1700\C1684\FP\F\Flow Calculations\F-A. 125 CUSTOMER INFORMATION Company Name: Facilities Protection Systems Company Address: 1150 W. Central Ave. Suite "D" Brea, CA 92821 Company Phone: 714-257-2244 Company Fax: 714-257-2240 Contact Information: F-A.125 Page 1 ECARO-25 Flow Calculation Software Agent Requirements - Enclosure 0001 (SERVER ROOM I MDF 121) Enclosure Area Enclosure Volume Added Volume Height Subtracted 0.00 ft L X 0.00 ft W 0.00 ft None None Design Maximum Minimum Maximum Elevation Concentration Concentration Temperature Temperature 8.00% 8.05 % at 70 OF 70 OF 70 OF 0 ft Fike Corporation Protected Volume 3650.00 ft3 Agent Required 101.0 lbs Nozzle Information - Pipe Network 0001 (Pipe Network 0001) Nozzle Number Type Enclosure Name Requested Agent 0101 1800 SERVER ROOM / MDF 121 101.0 lbs Total Agent Distributed Through Pipe Network: 101.0 lbs Cylinder Information - Pipe Network 0001 (Pipe Network 0001) Cylinder Type Agent Per Manifold Type Cylinder Valve to Cylinder to Cylinder Spacing Manifold Exit 70-154 215 lb (87 L) Upright 1 X 101 lbs No Manifold - - - Fill Density Empty Weight Floor Area Floor Loading 32.7 lbs / ft3 150 lbs 2.18 ft2 115 lbs / ft2 F-A.125 Page 2 ECARO-25 Flow Calculation Software Fike Corporation Pipe Network Isometric £-".t , •-J;.I'W• (101.0 Ib) F-A.125 Page 3 ECARO-25 Flow Calculation Software Fike Corporation Flow Calculation Input Data - Pipe Network 0001 (Pipe Network 0001) Equ Nozz Select Select Thru Side Union Length Cyl Type Agent Orifice Start End Length Elevation Select Select 9O Pipe DIa Pipe Sch 1 2 2.41 ft 2.41 ft 3 in SCH 40 1 4.09 ft 1 2 3 7.00 ft 7.00 ft 1 in SCH 40 T 3 101 12.50 ft -0.50 ft 1 in SCH 40 T 3 180 101.0 lbs 0.2770 in F-A.125 Page 4 ECARO-25 Flow Calculation Software Fike Corporation Flow Calculation Output Data - Pipe Network 0001 (Pipe Network 0001) Start End Pipe Type Equ Length Start Pressure End Pressure Flow Rate Agent Discharged Orifice Diameter 1 2 3 -SCH 40 6.50 ft 282 psia 281 psia 10.0 lbs/s 2 3 1 -SCH 40 7.00 ft 281 psia 265 psia 10.0 lbs/s 3 101 1 -SCH 40 20.37 ft 265 psia 238 psia 10.0 lbs/s 101.0 lbs 0.2770 in Flow Calculation Messages ECARO-25 Flow Calculation Software Version 3.30.0000 Calculation based on fixed nozzle codes and pipe sizes. Calculation performed on 2/12/2009 1:52:01 PM System calculated within limits of Pikes UL listing and FM approval F-A.125 Page 5 ECARO-25 Flow Calculation Software Fike Corporation Bill of Materials - Pipe Network 0001 (Pipe Network 0001) Cylinder List Qty Part Number Cylinder Description Agent Fill Amount 1 70-154 215 lb (87 L) Upright 101 lbs Nozzle List Num Part Number Nozzle Size Nozzle Type Drill Diameter 101 80-047-2770 1 -SCH 40 1800 0.2770 in Pipe List Qty Pipe Description 1 7.00 ft, 1 -SCH 40 1 0.50 ft, 1 -SCH 40 1 11.00 ft, 1 -SCH 40 1 1.00 ft, 1 -SCH 40 Fitting List Qty Fitting Description 3 900 Elbow, 1 -SCH 40 F-A.125 Page 6 ECARO-25 Flow Calculation Software Fike Corporation System Acceptance Report Pipe Network Discharge Time Pipe Network Discharge Time %Agent in Pipe Pipe Network Temperature 0001 - Pipe Network 0001 9.06s 16.02% 70 OF Enclosure 0001 (SERVER ROOM / MDF 121) - Nozzle Performance Nozzle Number Orifice Diameter Agent Requested Agent Predicted Nozzle Pressure 101 0.2770 in 101.0 lbs 101.0 lbs 238 psia Minimum Required Design Concentration Minimum Predicted Maximum Predicted Concentration Concentration Concentration 8.00% 8.00% 8.05 % at 70 OF 8.05 % at 70 OF F-A.125 Page 7