The URL can be used to link to this page

Home My WebLink About5805 ARMADA DR; ; FPC2016-0026; Permit(ãity PERMIT REPORT of Carlsbad Print Date: 05/10/2022 Permit No: FPC2016-0026 Job Address: 5805 ARMADA DR, CARLSBAD, CA 92008-4609 Status: Closed - Finaled Permit Type: FIRE-Construction Commercial Work Class: Fire Alarm Parcel #: Track #: Applied: 12/05/2016 Valuation: $0.00 Lot #: Issued: 12/19/2016 Occupancy Group: Project #: Finaled Close Out: 01/26/2017 #01 Dwelling Units: Plan #: Bedrooms: Construction Type: Final Inspection: Bathrooms: Orig. Plan Check #: INSPECTOR: Fieri, Dominic Plan Check #: Project Title: Description: GRAND PACIFIC PALISADES / FIRE ALARM PANEL REPLACEMENT Applicant: SIEMENS INDUSTRY INC P0 BOX 80600 INDIANAPOLIS, IN 46280-0600 (630) 857-2100 FEE AMOUNT FIRE TI Fire Alarm System $601.00 Total Fees: $601.00 Total Payments To Date: $601.00 Balance Due: $0.00 Fire Department Page 1 of 1 1635 Faraday Avenue, Carlsbad CA 92008-7314 1 760-602-4665 1 760-602-8561 f I www.carlsbadca.gov SIEMENS Industry, Inc. 1Q100 Willow Creek Rd Sand Diego, Ca 92131 Phone: 858-880-2085 Fax: 855-866-7942 Grand Pacific Palisades Fire alarm Panel Replacement 5805 Armada Drive Carlsbad, CA 92008 Enclosures, Doors & Plates CA1131 - Single-Row Enclosure Model CAB 1, the smallest of the FireFinder XLS enclosures, can house a single Model CAB-MP cabinet mounting plate for mounting card cages, power supplies and bulk amplifiers. Model CA131 also has four (4) mounting slots on the inner door for mounting a Person Machine Interface and Model ID- MP switch module brackets. Model CAB1 comes complete with a black back box, with black inner and outer doors, a single lock and key set on the outer door, and a single OD-LP outer door lens plate (installed). A red version (Model CA131-11) is also available. Approximate size is 27" (68.6cm.) high, 26' (66cm.) wide, and 8(20.3cm.) deep. SIEMENS Data Sheet Fire Safety Products F ireFinder® XLS Fire Alarm Enclosures & Equipment Models: CABI, CAB-BATT, CAB-BATT-R, CAB2-BB, CAB2-BD, CAB2-X, CAB2-XBD, CAB2-XRD, CAB3-BB, CAB3-BD, CAB3-X, CAB3-XBD, CAB3-XRD, CAB-MP, ID-MP, ID-SP, BCM, OD-LP, OD-BP, OD-GP, REMBOX2, REMBOX4, XLS-MLE6-ADPT, XLS-MME3-ADPT, XLS-MSE2-ADPT, XLS-MSE3-ADPT and XLS-RCCI3F-ADPT ARCHITECT AND ENGINEER SPECIFICATIONS One (1), two (2), and (3) three-row enclosures for the FireFinder XIS system Blank plates for inner and outer doors Lens and grill plates for outer door €UL 864 9th Edition Listed and ®ULC Listed; FM (9010), CSFM (#71650067:0222) & NYCFD (#6160) Approved Product Overview The FireFinder XLS fire alarm enclosures (Models CA131, CA132, and CA133) and their accessories provide a complete set of hardware for mounting all FireFinder XLS main system and remote transponder cards and modules. The hardware allows the FireFinder XLS system to be configured for a wide variety of applications, and allows for future system upgrades. Included in the enclosure series are backbox and door sets, removable mounting plates and clear lenses, louvered ventilation grill plates, and blank plates for use with the enclosure doors. All enclosures come with ground straps for the inner and outer doors, shield termination lugs, grounding lugs, and tie wrap lances for securing wire. All enclosures can also mount system backup batteries up to 31AH in capacity. FireFinder® XLS Enclosures 6327 SIEMENS Industry, Inc. Building Technologies Division Enclosures, Doors & Plates - (cont.'d) CAB1 Enclosure CAB2 - Two-Row Enclosure Model CAB2 is the mid-sized FireFrider XLS enclosure capable of housing a maximum two (2) Model CAB-MP cabinet mounting plates. The inner door has two (2) rows of four (4) mounting slots. The outer door has space for mounting two (2) outer door plated (Mod 2lS OD- LP, OD-BP or OD-GP). The outer door can be configured to open from either side. Model CAB2 consists of the Model CAB2-BB back box; the Mode CAB2-ED blac< inner and outer door package, and one (1) Model'OD-LP lens plate. The outer door has a single loci': and key set installed. Red doors are available in Model CAB-RD. Additional door mounting plates must be 16rdered separately. Approximate size is 45' (114.3c .) high, 26' (66cm.) wide, and 8(20.3cm.) deep. Enclosure Trim Kits Trim kits are available for all system enclosures for semi-flush mounting applications. Model CAB1-TK (for black enclosures) and Model CAB1 R-TK (for red enclosures) fit Models CAB1 and CAB1-R enclosures. Similarly, Models CAB2-TK and CAB2R-TK fit the Model CAB2 enclosure, and Models CAB3-TK and CAB3R-TK fit the Model CAB-3 enclosure. Remote Transponder Doors The FireFinder XLS system can use remote transpon- ders for mounting additional modules such as amplifiers without requiring a Person Machine Interface or any control switches. Special doors are available for systems using Model CAB2 or Model CAB3 remote transponders. Models CAB2-XBD and CAB3- XBD omit the unused inner door and come complete with ventilation louvers built into the door. Model CAB2-XBD comes in black, and fits on Model CAB2-BB. Model CAB3-XBD also comes in black, and fits on Model CAB3-BB. Remote transponder door are also orderable in red: Models CAB2-XRD and CAB3-XRD. Complete box and door kits are available as Models CAB2-X and CAB3-X. CAB2 Enclosure CA133 - Three-Row Enclosure Model CAB3, the largest single FireFinder XLS enclosure available, can house a maximum thee (3) Model CAB-MP cabinet mounting plates in the er :losure and three (3) rows of inner door mounting slots. The outer door can be configured to open from either side. Model CAB3 consists of the Model CAB3-BB back ox; theMode CAB3- BD black inner and outer door package, and one 1) Model OD-LP lens plate. The outer door has two (2) lock; and key sets installed. Red doors are available via Model CAB3-RD. Additional door mounting plates r.ust be ordered separately. Approximate size is 6. (160cm.) high, 26' (66cm.) wide, and 8 (20.3cm.) deep. I CAB3 Enclosure SIEMENS Industry, Inc. Building Technologies Division CAB2-XBD Door CAB3-XBD Door OD-GP - Outer-Door Grill Plate Model OD-GP also covers an entire row on the outer door of a system cabinet, but has four rows of ventilation louvers on it. Model OD-GP is mounted in front of system bulk amplifiers, card amplifiers, or other modules that generate heat. Using Model OD-GP will permit airflow across these modules to aid in heat dissipation. A single grill plate is included with each Model OG-GP. OD-GP Remote System Enclosures Models REMBOX2 and REMBOX4 are FireFinder XLS system enclosures that are used for remotely mounting inner-door modules, such as the Person Machine Interface, switch modules, live-voice modules, and Model FMTs. Enclosures, Doors & Plates - (cont.'d) REMBOX4 are FireFinder XLS system are thinner than the regular CAB enclosures (just 5" deep overall), and are perfect for mounting in places where space is limited (such as lobbies or behind a receptionist's desk). Due to their smaller depth, no card cages, power supplies or bulk amplifiers can be mounted in a REMBOX. However, modules such as the Remote Network Interface Module (Model RNI); the Output-Control Module (Model 0CM-1 6) and the Supervised Input Module (Model SIM-16) can be mounted in a REMBOX. Due to the depth of the live-voice module and the firefighters' master telephone, no Model 0CM-1 6 or Model SIM-i 6 modules can be used simultaneously with Model LVM or Model FMT. Both Models REMBOX2 and REMBOX4 are designed for flush mounting with no trim kit required. Both enclosures also come with a clear lens plate on the cover. REMBOX2 - Two-Module Remote Enclosure Model REMBOX2 has two (2) inner door module spaces, and can hold a single Model PMI-2, up to two (2) switch module brackets, one (1) Model LVM live voice module. Combinations are also allowed. Model REMBOX2 can also mount a single Model RNI on a bracket included in the backbox. A bracket (Model REMBOX2-MP) can be used to mount up to four (4) Model 0CM-1 6s or Model SIM-1 6 enclosures. Model REMBOX2- MP must be purchased separately. Approximate size of Model REMBOX2 is 14-1/2 (36.8cm.) wide, 18-112' (47cm.) high and 5" (12.7cm.) deep. REMBOX2 REMBOX2 (with doors closed) (with doors open) Note: A red, (2) two-module remote lobby enclosure (Model REMBOX2R) is also available. REMBOX4 - Four-Module Remote Enclosures Model REMBOX4 has space for mounting four (4) inner door modules. Any combination of Model PMI-2 (two- module spaces), switch module brackets, Model LVM or Model FMT (one-module space each) can be used. Unused module spaces can be covered with Model ID-SP blank plates. Model REMBOX4 can also mount to a single Model RNI on a bracket included in the backbox. A bracket known as Model REMBOX4-MP can be used to mount a maximum eight (8) Model 0CM-1 6s or Model SlM-i 6s. Model REMBOX4-MP must be purchased separately. Approximate size of Model REMBOX4 is 24' (61 cm.) wide, 18-1/2" (47cm.) high and 5" (12.7cm.) deep. SIEMENS Industry, Inc. Building Technologies Division REMBOX4 REMBOX4 (with doors closed) (with doors open) Note: A red, (4) four-module remote lobby enclosure (Model REMBOX411) is also available. CAB-MP - Cabinet Mounting Plate The cabinet mounting plate (Model CAB-MP) provides mounting for a single row of modules in a FireFinder XLS cabinet. Four (4)-module spaces are available on Model CAB-MP. Model CAB-MP is used to mount the Model CC-5 card cage, the Model CC-2 card cage, the Model PSC- 12 power supply, the Model PSX-1 2 power supply extender, and the Model ZAM-80 / 180 zone amplifiers. CAB-MP ID-MP - Inner Door Mounting Plate The inner door mounting plate (Model ID-MP) is mounted on the inner door of a CAB enclosure. Model ID-MP plates are used to mount Model SCM-8 switch control modules; Model LCM-8 LED control modules, or with Model FCM-6. Four (4) mounting plates are included in each Model ID- MP. Each mounting plate has four (4) spaces for control modules, and can hold either four (4) Model SCM-8 modules (one [1] control module space each}; four (4) Model LCM-8 modules {one [1] control module space each}; or two (2) Model FCM-6 modules {two [2] module spaces each}. Combinations are also allowed. Blank spaces in Model ID-MP can be covered using the Model BCM blank control module plate. A maximum four (4) Model ID-MP plates can be mounted in a single row on the inner door. Enclosures, Doors & Plates - (cont.d) ID-SP - Inner-Door Single Blank Plate Model ID-SP is used to cover any single mdu1e blank spaces on the inner door not used to fount the Person Machine Interface or one (1) Model ID-MP. Up to four (4) Model ID-SP plates can be mounted in a single row on the inner door. Two (2) blank plates are included in each Model ID-SP. ID-SP BCM - Blank Control Module plate Model BCM is used on Model ID-MP to cover any blank areas where control modules are not usec. A maximum four (4) Model BCM plates car be mounted on a single Model ID-MP. Four (4), blank-module plates are included in each Model BCM. BCM OD-LP - Outer Door Lens Plate Model OD-LP is a clear plastic lens plate mounted on the outer door of a system cabinet. Model OD-LP is used to allow operators to see the system interface and controls mounted on the inner door, but restricts a:cess to unauthorized users. Model OD-LP covers En entire rcw on the outer door. A single lens plate is included win each Model OD-LP. OD-BP - Outer-Door Blank Plate The Outer Door Blank Plate (Model OD-BP) is used to cover an entire row of a XLS system cabinet. Model OD-BP is mounted when no module is used in :bat location. Model OD-BP is mounted on the outer door, and one (1) blank plate is included with each orcer. XLS-MSE2/R-ADPT - XLS MSE-2/11 Enclosure Adapter Model XLS-MSE2-ADPT, which must be used in conjunction with Model CAB-MP, is an adapter that allows FireFinder XLS cards to be mounted in older- generation MXL Model MSE-2 small black enclosures. Model XL-MSE2R-ADPT, which must be used in conjunction with Model CAB-MP, is an adapter that allows FireFinder XLS cards to be mounted in older- generation MXL Model MSE-2R small red enclosures. XLS-MSE2-ADPT XLS-MME3/R-ADPT - XIS MME-3/11 or MBR-2 Enclosure Adapters Model XLS-MME3-ADPT, which must be used in conjunction with Model CAB-MP, is an adapter that allows FireFinder XLS cards to be mounted in older- generation MXL Model MME-3 or Model MBR-2 medium back enciosures. Model XLS-MME3R-ADPT, which must be used in conuncton with Model CAB-MP, is an adapter that alows FireFinder XLS cards to be mounted in older- generation MXL Model MME-3R medium red enclosures. XLS-MME3-ADPT XLS-MLE6/R-ADPT - XIS MLE-6/11 Enclosure Adapter Model XLS-MLE6-ADPT, which must be used in conjunction with Model CAB-MP, is an adapter that allows FireFinder XLS cards to be mounted in older- generation MXL Model MLE-6 large black enclosures. Model XLS-MLE6R-ADPT, which must be used in corjunc:on with Model CAB-MP, is an adapter that allows FireFinder XLS cards to be mounted in older- generation MXL MLE-6R large red enclosures. OD-BP - • XLS-MLE6-ADPT SIEMENS Industry, Inc. Building Technologies Division Enclosures, Doors & Plates - (cont'd) Details for Ordering XLS-MSE3/R-ADPT - XLS MSE-31_/11 or MSE-3M/R Enclosure Adapters Model XLS-MSE3-ADPT is an adapter that allows FireFinder XLS cards to be mounted in the older generation MXL-IQ Model MSE-3L or Model MSE-3M black enclosure. Model XLS-MSE3R-ADPT is an adapter that allows FireFinder XLS cards to be mounted in the older generation MXL-IQ Model MSE-3LR or Model MSE-3MR red enclosure. gull XIS- MSE3-ADPT XLS-RCC-1-ADPT - XLS RCC-1 Enclosure Adapter Model XLS-RCC1-ADPT is an adapter that allows the FireFinder XLS Model SSD/-C series remote annunciator to be mounted in the older generation Model RCC-1 surface-mount enclosure. XLS-RCC1 -ADPT XLS-RCC1 3F/R-ADPT - XIS RCC-1 FIR or RCC-3FIR Enclosure Adapters Model XLS-RCC1 3F-ADPT is an adapter that allows the FireFinder XLS Model SSD/-C series remote annunciator to be mounted in the older generation Model RCC-1 F or Model RCC-3F black, flush-mount enclosure. Model XLS-RCC1 3FR-ADPT is an adapter that allows the Model SSDI-C series to be mounted in the older generation RCC-1 FR (red) and RCC-3FR (red) flush-mount enclosure. XLS-RCC1 3F-ADPT Temperature and Humidity Range Products are ®UL 864 91h Edition listed for indoor! dry locations within a temperature range of 120+1-3°F (49+/-2°C) to 32+/-3°F (0+/-2°C) and a relative humidity of 9342% at a temperature of 90+/-3°F (32+1-20C). SIEMENS Industry, Inc. Building Technologies Division Model Part Number Description BCM 500-033320 Blank control module plate, four [4] per package CAB-1 500-633007 Complete single-row cabinet, black CAB-1 R 500-633728 Complete single-row cabinet, red CABi -TK 500-633013 single-row trim-kit cabinet, black CAB iR-TK 500-633729 Single-row trim-kitcabinet, red CAB2-BB 500-633009 (2) Two-row back box, black CAB2-RB 500-634941 (2) Two-row back box, red CAB2-BD 500-633008 (2) Two-row inner & outer door set, black CAB2-RD 500-633755 (2) Two-row inner & Outer door set, red CAB2-TK 500-633014 (2) Two-row trim-kit cabinet, black CAB2R-TK 500-633753 Two-row trim-kit cabinet, red CAB2-XBD 500-633768 CAB2transponderdoor, black CAB2-XRD 500-633792 CAB2transponderdoor, red CAB2-X 599-034252 Complete CAB2 w/ transponder door [no inner door] CAB3-BB 500-633011 Three-row back box, black CAB3-RB 500-634942 (3) Three-row back box, red CAB3-BD 500-633010 (3) Three-row inner & outer door set, black CAB3-RD 500-633757 (3) Three-row inner & outer door set, red CAB3-TK 500-633015 (3) Three-row trim-kit cabinet, black CAB3R-TK 500-633754 (3) Three-row trim-kit cabinet, red CAB3-XBO 500-633769 1 CAB3 transponder door, black CAB3-XRD 500-633793 CAB3 transponder door, red CAB3-X 599-034253 Complete CAB3 w/ transponder door [no inner door] CAB-BAIT 500-633917 Field-mounted enclosure for 100AH batteries, black CAB-BAIT-R 500-634925 Field-mounted enclosure for 100AH batteries, red CAB-MP 500-633012 lBack box module mounting plate ID-MP 500-633027 Inner-door enclosure mounting plate, four [4] per package ID-5P 500-633028 single-module inner-door enclosure mounting plate [two (2) per package] OD-BP 500-633017 Outer door blank plate OD-BP-R 500-634919 Outer door blank plate, red O0-GP 500-633018 Outer door grill plate OD-GP-R 500-634920 Outer door grill plate, red OD-LP 500-633016 Outer door lens plate REMBOX2 500-633772 (2) Two-module remote lobby enclosure, black REMBOX211 500-650612 (2) Two-module remote lobby enclosure, red REMBOX2-MP 500-634211 Mounting plate for Models 0CM-1 6/ 51M-1 6 in Model REMBOX2 REMBOX4 500-633914 (4) Four-module remote lobby enclosure, black REMBOX413 500-650613 (4) Four-module remote lobby enclosure, red REMBOX4-MP 500-634212 Mounting plate for Models 0CM-1 6 / XLS-MLE6-ADPT S54430-C9-A1 I MLE-6 enclosure adapter for XLS, black XLS-MLE6R-ADPT S54430-C9-A2 MLE-6R enclosure adapter for XLS, red XLS-MME3-ADPT S54430-C8-A1 MME-3 and MBR-2 enclosure adapters for FireFinder XLS, black XLS-MME3R-ADPT S54430-C8-A2 MME-3R enclosure adapter for XLS, red XLS-MSE2-ADPT S54430-0-A1 MSE-2 enclosure adapter for XLS, black XLS-MSE2R-ADPT S54430-C7-A2 MSE-2R enclosure adapter for XLS, red XLS-MsE3-AoPT S54430-C14-A1 MXL-IQ M5E-3L and MSE-3M enclosure adapters for XLS, black XLS-MSE3R-ADPT S54430-C14-A2 MXL-IQ MSE-3LR& M5E-3MRenclosure adapters for XLS, red XLS-RCCi-ADPT S54430-Z14-A1 RCC-1 enclosure adapter, black XLS-RCC13F-ADPT 554430-Z13-A1 RCC-i F & RCC-3F enclosure adapters, black LS-RCC13FR-ADPT 554430-Z13-A2 RCC-iFR & RCC-3FR enclosure adapters, red Notice: This marketng data sheet is not intended to be used for system design or instal =-tion purposes. For the most up-to-date information, refer to each product's installation instruc:ioris. Fire Sarety Fire Safety 8 Fern'%ood Road 1577 Nor-.-1, Service Road SIEMENS Industry, Inc. Florham Park, NJ 07932 East Oakvi le, 0n:ario January 2015 Building Technologies Division Tel: (973) 593-2600 sll-Fs 1-61-101-16, Carada Supersedes sheet dated 9/14 FAX: (908) 547-6877 Printed in US A. Tel: [9051 465-8000 Rev. 10) URL: www.usa.5iemens.com/Fire URL: www.Siemens.CA SIEMENS Data Sheet Fire Safety Products FireFinder® XLS Advanced Fire Alarm Control Panel ARCHITECT AND ENGINEER SPECIFICATIONS Standard! 2500-point-capacity addressable fire-alarm control panel (FACP) Ability to network with other FireFinder XLS systems Powerful, easy-to-use programming capabilities Fully field programmable, via Windows® laptop PC 6", backlit LCD display User-friendly system interface Touch screen for maintenance operations and function keys Global annunciation and control capability Multi-language display Universal AC power input: 120VAC— 240VAC@50!60Hz 12 amps of system power (expandable to 48 amps) Numerous Relays: Alarm, Trouble, Programmable, etc. SureWireTm addressable-loop technology Polarity-insensitive detection circuits (patented) Useful diagnostic LEDs on all cards Supports FirePrintlm application-specific detection Intelligent/ analog detection circuits: 'Class A' or 'Class B' Supports single-person 'Walk Test' Seismic certified System Overview Modular assembly Supervised remote printer 32-character custom messages Thermal strip printer Security-device monitoring (UL 1076 Listed) Sprinkler Supervision Degrade-mode operation User help screens Coded outputs Supported by all Fire Safety Management Stations UUKL Listed for smoke control ®UL 864 9th Edition Listed & €ULC Listed; FM, CSFM & NYC Fire Dept. Approved Multiple command stations Menu-driven operator commands 5000-event, history-logging capability with on-line and off-line reports Multiple levels of password protection Automatic environmental compensation for smoke detectors Alarm verification by device or zone Pre-alarm operation Logic-controlled output functions Ti me-based-control led output functions Holiday schedule City tie/ leased line 200 notification-appliance-circuits (NACs) capacity Up to 3.0 amps (24VDC) per NAC Built-in strobe synchronization protocol Supports pre-action, deluge and agent releasing Voice evacuation system (optional) NEC 760 power-limited circuits ((DUL 864 Compliant) Intelligent interface to building / process management systems Operates as interactive peer with other XLS or XLSV units in a XNET network Distributed processing Detector Sensitivity Readout/ Printout per NFPA72 FireFinder XLS is a microprocessor-based, advanced life-safety system that has a 6 display and large, lighted buttons; making it a highly intuitive fire-alarm user interface. Through the use of the unique multiprocessor'Network' design - along with the ability to utilize analog and conventional detection devices - FireFinder XLS exemplifies a flexible and configurable life-safety system. FireFinder XLS is ideally suited for commercial, institutional and industrial fire detection and notification applications. This FACP complies with the requirements of NFPA Standard 72, and is listed by Underwriters Laboratories under their ®UL 864 standard. Underwriters Laboratories of Canada also lists FireFinder XLS FACPs under ULC-S527. FireFinder XLS is Factory Mutual (FM 03010) Approved; as well as California State Fire Marshals (CSFM 47165- 0067:0222) and NYC Fire Department (46160) Approved. Additionally, FireFinder XLS is ®UL Listed under the category UUKL for smoke control. FireFinder XLS is also ®UL Listed and FM Approved for Sinorix® clean-agent systems and pre-action or deluge sprinkler systems, which include foam or water applications. FireFinder XLS operates on the releasing requirements specified in NFPA 13 and 2001. FireFinder XLS is listed as a Fireman's Smoke Control Station in high-rise office buildings, malls and other large structures. FireFinder® XLS System Overview 6300 SIEMENS Industry, Inc. Building Technologies Division System Overview -(continued) The FireFinder XLS system has been seismic qualified in accordance with: International Building Code, 2006 Edition California Building Code, 2007 Edition ASCE Standard 7, 2005 Edition OSHPD, OSP-0057-10 OSHPD CAN 2-1708A.5, Rev. 3 ICC-ES AC 156, effective 1/112007 System Components A basic FireFinder XLS FACP consists of the following sub- assemblies: Person Machine Interface (Model PMI-2); Power Supply (Model PSC-i 2); Device Loop Card (Model DLC): Zone Indicating Card (Model ZIC-4A); Card cage (Model :c-); Inner Door Blank Single Plate (Model ID-SP); CAB-1, CAB-2 or CAB-3 enclosures. Optional modules that can be installed with this FACP include: Card Cage (Model CC-2); Network Interface Card (Model NIc-C); 8-Circuit Zone Indicating Card (Models ZIG- 8B I ZIC-20; Control Relay Card (Model CRC-6); Output Control Module (Model 0CM-1 6); Switch Control Module (Model SCM-8); LED Control Module (Model LCM-8); Fan Control Module (Model FCM-6); Supervised Input Module (Model SIM-i 6); Power Supply Extender (Model PSX-1 2); Remote Network Interface (Model RNO; Remote Printer Module (Model RPM); System Status Display (Model SSJ); Multi-Point Digital Alarm Communicator (Model MDACT); Two-Module Remote Enclosure (Model REMBOX2); Four- Module Remote Enclosure (Model REMBOX4). FireFinder XLS is compatible with a full line of intelligent initiating devices, highlighted by the FirePrint appli:ation- specified detectors: Models HFP-1 1 and HFPT-1 1. XLS functions with the Siemens Fire Safety portfolio of graphics command centers. 52 1 PM 1-2 ->Person Machine Interface 2 PMI-2 - Person Machine Interface 2 The Person Machine Interface 2 (Model PMI-2) is :he primary user interface and central microprocessor for the FireFinder FACP. Model PMI-2 uses large, lighted buttons to prompt users as to the next correct system operation that is availaole (Acknowledge, Silence, Unsilence, Audible or Res-et). From each Model PMI-2 interface, the end-user can Acknowledge events; control the system notification appliance circuits (NACs), and reset the system. Detailed information about the nature and location of the events can also be display2d. The controller in Model PMI-2 provides all system logic aid supervision. Model PMI-2 contains a large (1/4 VGA), 6 (15.2 cm.), 1200 -x- 800 pixel full-color liquid-crystal (LCD) display, touch screen and LEDs for displaying system status. A sound is made when there is any unacknowledged event from Model PMI-2. The display is surrounded by keys that are used to control the displayed information and to navigate through these screens. Keys are also provided to obtain and enter 'Help into the menu features of Model PM7-2. Overlays --available in Spanish, Portuguese and French -- provde name in alternate languages for the textfound on the front of each Model PMI-2. Each overlay is a5signed on the outer assembly, respectively, when affixed to the display on the user interface. Each overlay assignment is intended for use in combina:ion wfth the run-time, alternate-language files found in the custom-configuration software tool, Zeus. Fire Safety Management Stations - XLS Compatible FireFinder XLS Compatibility with Siemens Fire Safety Management Stations FireFinder XLS panels are compatible with Siemens Fire Safety Management Stations, which provide integrated and reliable FACP monitoring and control of XLS sys:em events - including: Alarm, Trouble, Security and Supervisory commands. Each management station includes PC-based, color- graphics software designed for use with the XN:_T network, offering full control and annunciation. An extensive history log of all XLS-FACP events, as well as extensive report-generation capabilities, is easily maintained. Additionally, user-programmable furic:ion buttons allow site-specific control functions. SIEMENS Industry, Inc. Building Technologies Division ZIC-4A -*Zone Indicating Card ZIC-4A Zone Indicating Card The Zone Indicating Card (Model ZIC-4A) provides four (4) fully supervised, programmable output circLits for use on each FireFinder XLS. Model ZIC-4A supplies four (4) 'Class B' (Style Y) or 'Class A' (Style Z) type output circuits, power limited to 3.0 amps maximum per circuit. FireFinder XLS Components —(cont.'d) Each circuit for Model ZIC-4A can be independently programmed for use with listed audible or visual notification appliances; listed emergency audio speakers; municipal tie boxes; leased lines, or as releasing circuits. Model ZIC-4A plugs into one (1) slot in the Model CC-5 or Model CC-2 card cage, and has on-board LEDs for system status and troubleshooting. Indication of power, communication, internal operation, and ground-fault conditions are provided, as well as indication of circuit activation or Trouble conditions. ZIC-8B I ZIC-2C -* Zone Indicating Cards ZIC-81131 / ZIC-2C The Zone Indicating Card (Model ZIC-8B) provides eight (8) fully supervised, programmable output circuits for use on FireFinder XLS. Model ZIC-813 supplies eight (8) 'Class B' (Style Y) type output circuits, power limited to 2.0 amps maximum per circuit. Each circuit can be independently programmed for use with listed audible or visual notification appliances, or listed emergency audio speakers. Model ZIC- SB plugs into one (1) slot in the Model CC-5 or Model CC-2 card cage, and has on-board LEDs for system status. Model ZIC-2C mounts directly on Model ZIC-813, and allows each of the Model ZIC-8B output circuits to be used for two-channel voice applications. Indication of power, communication, internal operation, and ground-fault conditions are provided, as well as indication of circuit activation or Trouble conditions. DLC Device Loop Card The Device Loop Card (Model DLC) is the interface for connection with FireFinder XLS detectors and initiating devices - including manual stations, control and input devices. Model DLC plugs into one (1) slot of the CC-2 or CC- 5 card cage. Programming Model DLC is accomplished using the FireFinder XLS system-programming tool, Zeus. Model DLC takes one (1) address on the network, and communicates with two (2) device circuits for a total of 252 detectors and devices. Model DLC has 12 LEDs for diagnostic purposes, and provides ground-fault detection and zone- isolation circuitry. SIEMENS Industry, Inc. Building Technologies Division N IC-C -* Network Interface Card NIC-C Network Interface Card The Network Interface Card (Model NIC-C) provides HNET or XNET network communications between enclosures. In addition to the HNET or XNET communication, Model NIC-C provides CAN network communication within an enclosure or external to the enclosure. HNET or XNET communication can be wired Style 4 or Style 7, but the CAN network can be wired Style only. When used for HNET communications, Model NIC-C provides communication between enclosures on a single system. When Model NIC-C is used for XNET communications, Model NIC-C provides communication between systems. The maximum of XNET Model NIC-C cards on a single system (single node) is one (1), fora total of 64 XNET Model NIC-C cards on a peer-to-peer networked system. Model NIC -C has diagnostic LEDs that indicate: Card Fail, CAN Fail, HNET Fail, XNET Fail, Ground Fault, Loop 'A' Fail and Loop 'B' Fail. Model NIC-C Card also has LEDs to indicate Power, Style and Active Networks. HCP -* Control Point Module HCP Control Point Module Model HCP provides an intelligent control point for the FireFinder XLS. Model HCP can be programmed as an independent, remotely located telephone zone, speaker zone or notification appliance circuit. Model HCP is designed to be used with the Siemens - Fire Safety Alarm Signaling Devices product line. Model HCP communicates through the Model DLC analog loop, and can be wired either 'Class A' (Style Z) or 'Class B' (Style Y). The 24 VDC power input comes from either the control panel or from any ®UL Listed power-limited, auxiliary power supply. FireFinder XLS Components - (cont.'d) CRC-6 Controllable Relay Card M LC -* MXL Line Card [for FireFinder XLS] MLC - MXL Line Card [for FireFinder XLS] The MXL Line Card (Model MLC) is an optional card for the FireFinder XLS panel that supplies two (2; intelligent analog circuits, utilizing the Model '1 series; Model 'ID 'series; Model 'IL' series or Model ' EP 'series- type intelligent devices. Model MLC occupies two (2) addresses on the HNET network, and devices connected to the Model MLC circuits are dynamically supervised by FireFinder XLS through the use of a unique communications protocol. The Controllable Relay Card (Model CRC-6) is used with the F:reFinder XLS FACP. Model CRC-6 is designed to provide auxiliary control of building functions, such as: doc.r-holdcr release, elevator capture, smoke control, lock release, etc. Model CRC-6 plugs into one (1) slct in the Mc Jel CC-5 or Model CC-2 card cage. Model CRC-6 provies six (6), fully programmable relays. Each relay contains one (1) set of SPDT contacts rated at 4 Amps 30 VDC I 120VAC resis:ive and 3.5 amps 120VAC inductive (0.6 P. F.) SJM-16 -> Supervised Input Module NRC - Network Ring Card NRC Network Ring Card - Second Generation Model NRC, which is the 2nd generation of Model NRC, is a networking ring card that transmits single-mode or multi- mode network communication via fiber-optic or copper lines. Each card uses a 'Class A' (Style 7) ring configuration for connection with each FireFinder XLS FACP. One (1) Model NRC (per system node) provides XNET, peer- to-peer communication between FireFinder XLS FACPs, allowing a max, 64, XLS FACPs to be networked together. SIM-1 6 Supervised Input Module ft3 Supervised input Module (Model SIM-1 6)is a remotely ocated, general-purpose input module. Model SIM-1 6 provides 16 input circuits for remote system monitoring. Each input can be individually programmed as superviseë (dry-contact only) or unsupervised (general- purpose inpLt.) Model SIM-1 6 has two (2) 'Form C' relays. The relays and inputs are programmed using the Zeus system software-programming tool. FCM-6 -* Fan, Motor, Dampers Control Module CDC-4 —Conventional Detector Card CDC-4 Conventional Detector Card The Conventional Detector Card (Model CDC-4) is used to monitor Siemens Fire Safety conventional detectors on the FireFinder XLS system. Model CDC-L can be used in applications where conventional detectors are more suited than addressable detectors, such as hallways or large meeting rooms. Also, Model CDC-4 can be used to upgrade Siemens conventional fire-alarm panels to the FireFinder XLS system without requiring detector replacement. SIEMENS Industry, Inc. Building Technologies Division FCM-6 Fan, Motor, Dampers Control Module The Fan, Motor, Dampers Control Module (Model FCM-6) is a FireFinder XLS command-console option module that provides manual control of building HVAC system fans, motors, and dampers. Each Model FCM-6 module provides six 6) sets of three (3) push-button switches for manual- system control. Each switch has three (3), associated LEDs to indicate Fan I Damper! Motor status: OFF (RED LED), ON (GREEN LED), Trouble (YELLOW LED). FireFinder XLS Components —(conL'd) - CC-2 —*Card Cage-2 Slots CC-5 -+Card Cage-5 Slots CC-5 I CC-2 Card Cages The Models CC-5 I CC-2 card cages provide the physical mounting location and all wiring connection points for all fire-and-voice system options cards for the FireFinder XLS system. Model CC-5 has five (5) slots, while Model CC-2 has two (2) slots. All cards plugged into the CC-5 I CC-2 card cage communicate with other FireFinder XLS modules via a common data bus. Connectors are provided on the left and right side of the CC-5 to connect a 60-pin cable for communications with the FireFinder XLS operator interface, power supplies and amplifiers modules. Field wiring to devices and circuits terminates on the Models CC-5 / CC-2 card cages. All cards designed for use with the Models CC-5 / CC-2 route their field wiring terminations to the 'top' of the Model CC-5 / CC-2 card cages. These connections are all power limited. Internal wiring connections distribute 24VDC to cards or high-level audio signals (depending on application used) connect to the 'bottom' of the Model CC-5 I CC-2 card cages. These connections are all non-power limited. All wiring connections to the Model CC-5 / CC-2 card cages are to removable terminal blocks. Terminal blocks are rated for use with wire sized 12 American Wire Gauge (AWG) to 24AWG. Each connector is numbered to make wiring terminations to the correct position on the terminal block simple in order to reduce potential wiring errors. SCM-8 -4 Switch Control Module SCM-8 Switch Control Module The Switch Control Module (Model SCM-8) is a FireFinder XLS-option module that provides manual control to the Emergency Voice Evacuation System (EVAC) or manual fire-system control. Each Model SCM-8 module provides eight (8) momentary push-button switches and 16 light-emitting diodes (LEDs) to indicate their status. Each switch is assigned two (2) LEDs, as well as a label to indicate the switch's programmed usage. The label slides behind a clear protective membrane. One set of LEDs assigned to each switch is a dual-colored LED, which is used to indicate what type of signal is active. SIEMENS Industry, Inc. Building Technologies Division Each Model SCM-8 switch is fully programmable, and may be used to control speaker circuits and a wide range of general-system functions such as: All Call, All Evac, Warden's Page, Speaker, etc. Any number of circuits may be grouped and controlled by a single switch. Switch usages and zone groupings are assigned using the Zeus system software-programming software. Model SCM-8 modules are mounted on a hinged panel, as a part of the PireFinderXLS Command Console enclosure. LCM-8 -* LED Control Module LCM-8 LED Control Module The LED Control Module (Model LCM-8) is a FireFinder XLS-option module that provides LED annunciation for FireFinder XLS system activity. Each Model LCM-8 contains eight (8) groups of two (2) LEDs - each of which can be assigned to desired outputs using the Zeus system software-programming tool. Eight (8) LEDs are dual-color capable (Red or Green / flashing or steady). The remaining LEDs are Amber flashing or steady. A space is provided for labeling of LED functions. The label slides behind a clear, protective membrane. Model LCM-8 dimensions are identical to Model SCM-8, and Model LCM-8 is mounted on the same hinged panel, as a part of the FireFinder XLS Command Console enclosure. RN! -* Remote Network Interface RN! Remote Network Interface The Remote Network Interface (Model RNI) provides a connection point for use with equipment mounted in a remote-lobby enclosure on the FireFinder XLS FACP. Model RNI is used to provide additional input, output and control features to the system remotely, via the main FACP. These additional features may include control switches and indicators: (Models SCM-8, LCM-8 and FCM-6), remote-emergency paging microphones or telephones: (Models LVM, FMT), or controls used in graphic annunciators (Models SIM1 6, 0CM-1 6) or system-status display with the ability to acknowledge alarms, silence audibles and reset the system (Model SSD-C-REM). Model RNI allows The Person Machine Interface to be mounted in the Model REMBOX2 or Model REMBOX4 remote lobby enclosure. FireFinder XLS Components - (ont.'d) t him,, ti H Ii II Ii 41 II Ii II II It II. II H hi Th PSC-1 2 Power Supply Charger Module PSC-1 2 Power Supply Charger Module The Power Supply Charger Module (Model PSC-i 2) is a high-current power supply that provides the PireFin:ler XLS primary-regulated 24VDC power to operate. Model PSC-12 is rated at 12Amps (Alarm)! 5Amps (Standby), and has a built-in battery charger, capable of charging up to 100 AH batteries. Model PSC-i 2 is an add ressable-ntelligent, microprocessor-controlled module that communicates its status to the system-operator interface. Each Person Machine Interface is then able to query the status of the power supply to obtain dEta regarding system-charging current, terminal-loading information, ground-fault conditions and more. PSX-12 -* Power Supply Exiender PSX-12 Power Supply Extender The Power Supply Extender (Model PSX-i 2) is a high-current, auxiliary power supply that expands the main Model PS-i 2 power supply and battery charger of the FireFinder XLS system with an additional 24VDC power. Model PSX-1 2 is rated at 12 Amps. RPM -* Remote Printer Module RPM Remote Printer Module The Remote Printer Module (Model RPM) provide; a means of connecting the FireFinder XLS system to a printer, such as Model PAL-1, for creating a hard copy of system status and configuration report;. Concurrently, Model RPM provides an output port that can be configured to communicate with external systems. SIEMENS Industry, Inc. Building Technologies Division PTB -* Power Term inatior; Board PTE Power Termination Board Model PSC-T 2 comes packaged with a m3due called the Power Termination Board (Model PTB). Model PTB is required for operation with Model PS-12. Model PTB filters the power 1om the incoming AC mains, and distributes it :o the Model PS-12 power supply and the optional Model PSX-12 power-supply extender. Model PTB has an optional connector that can be used during system installation, commissioning anc service to provide the technicia n with a place to plug in their laptop PC, if required. Model AC-ADPT is an optional accessory cable tha: allows connection on one side to Model PTB, via a keyed connector and on the other end directly into to the lap:ops trarsformer. Most laptop-computer external power t'ansformers have rerncvable AC power cords, which can be replaced by the opticnal Mcdel AC-ADPT to temporarily provide an AC power source for laptop-PC usage during system ins:ailation service and maintenance calls when needed. TSP-40A -* Thermal Strip Printer TSP-40A Thermal Strip Printer The Thermal Strip Printer (Model TSP-40A) is designed for use with the FireFinder XLS system. Mocel TSP-40A acts ES an event-logging device, providing a permanent history report of all system activity. Model TSP40A mounts in the FireFirder XLS Model CAB -, Model CAB2 or Model CAB3 enclosure, and its printout is visible thrc•ugh a window in the locked-acor enclosure. Prin:outs ee automatically spooled onto a take-up reel for tidy, uniformed records storage. FireFinder XLS Components - (cont.'d) RN! Remote Network Interface System-Status Display SSD-Series System-Status Display The System Status Display (SSD-series model displays) is a remote LED I LCD display that shows the local status of a FireFinder XLS system. An LED illuminates when Alarm, Supervisory, Trouble, and Security events occur on the system. A (4) four-line liquid-crystal display (LCD) will give details of the event in alphanumeric form. The display can be toggled to display additional events. Optional remote system control capabilities are available. Models SSD-C, SSD-C-INT, and Model SSD-C-REM have three (3) additional control buttons to acknowledge events, silence audible circuits, and reset the system. i10 IIC — Interface Isolation Card IIC - Interface Isolation Card The Interface Isolation Card (Model TIC) is designed to isolate network signals when used with a Model NCC ring configuration, via Model NRC. Model TIC executes the aforementioned isolation by removing the backplane network signals from each Model CC-2 card cage. Model TIC also provides one (1) end of CAN termination on each side of Model CC-2. Models SSD-C and SSD-C-INT have an integral keyswitch that enables these control buttons to operate. Model SSD-C-REM is located within a locked cabinet. Therefore, no additional keyswitch is required for manual activation of the control buttons. SIEMENS Industry, Inc. Building Technologies Division MDACT - Multi-Point Digital Alarm Communicator Transmitter MDACT - Multi-Point Digital Alarm Communicator Transmitter The Multi-Point Digital Alarm Communicator Transmitter (Model MDACT) is used in FireFinder XLS systems where point identification of Alarm, Supervisory, Security and Trouble events is required at Central or Remote Receiving Stations. An intelligent RS-485 communications protocol transmits all system information to Model MDACT. The installer selects the specific event or groups of events that are set to transmit from Model MDACT over phone lines to listed receiving station equipment. In turn, Model MDACT can transmit point information, via the Ademco Contact ID and the SIA protocol. A mounting plate (Model MOM2-XMP), MOM-2 card cage, and an XMl Interface Card are required for installation. CAB1 -* Single Row Enclosure CAB1 Single Row Enclosure Model CAB 1, the smallest of the FireFinder XLS enclosures, can house a single Model CAB-MP cabinet mounting plate for mounting card cages, power supplies and bulk amplifiers. Model CAB1 also has four (4) mounting slots on the inner door for mounting The Person Machine Interface and Model ID-MP switch module brackets. Model CAB1 comes complete with a black back box; black inner and outer doors; a single lock and key set on the outer door; a single, installed cabinet mounting plate (Model CAB-MP), and a single, installed outer door lens plate (Model OD-LP). A red version (Model CAB1-R) is also available. Approximate size: 27 (68.6cm.) high, 26(66cm.) wide, and 8(20.3cm.) deep. FireFinder XLS Components - (cont.'d) CAB2 -* Two-Row Enclosure CAB2 Two-Row Enclosure The Two-Row Enclosure (Model CAB2) is the mid-sized FireFinder XLS enclosure capable of housing up to two (2) Model CAB-MP cabinet mounting plates. The inner door has two (2) rows of four (4) mounting slbts. The outer door has space for mounting two (2) outer door plates (Models OD-LP, OD-BP or OD-GP), and can be configured to open from either side. Model CAB2 consists of the black Model CAB2-BB back box, the Model CAB2-BD black inner and outer door package, and one (1) Model OD- LP lens plate. The outer door has a single lock and key set installed. A red version (Model CAB2R) is also available, and a CAB2- RB back box is used with Model CAB2R. Approximate size is 45" (114.3cm.) high, 26" (66cm.) wide, and 8" (20.3cm.) deep. CAB3 -* Three-Row Enclosure CAB3 Three-Row Enclosure Model CAB3, the single largest FireFinder XLS enclosure available, can house a maximum three (3) Model CAB-MP cabinet mounting plates in the enclosure, and three (3) rows of inner-door mounting slots. The outer door can be configured to open from either side. Model CAB3 consists of the Model CAB3-BB back box, the Model CAB3-BD black inner and outer door package, and one (1) Model OD-LP lens plate. The outer door has two (2) locks and key sets installed. Ared version (Model CAB3R) is also available. Approximate size is 63 (1 60cm.) high, 26 (66.4cm.) wide, and 8(20.3cm.) deep. CAB-MP -* Cabinet Mounting Plate SIEMENS Industry, Inc. Building Technologies Division CAB-MP Cabinet Mounting Plate The Model CAB-MP cabinet mounting plate provides mounting for a single row of modules in a FireFinder XLS cabinet. Four (4) module spaces are available on Model CAB-MP, which is used to mount the Model CC-5 card cage; the Model CC-2 card cage; the Model PSC-1 2 power supply; the Model PSX-1 2 power-supply extender, and the Model ZAM-80 /180-zone amplifiers. Enclosure Trim Kits Trim kits are available for all system enclosures for semi- flush mounting applications. Model CAB 1-TK (for black enclosures) and the Model CAB1 R-TK (for red enclosures) fit inside the Models CAB1 and CAB1-R enclosures. Similarly, Models CAB2-TK and CAB-2R-TK fit inside the Model CAB-2 enclosure, while Models CAB3-TK and CAB3R- TK fit the Model CAB-3 enclosure. Remote Transponders The FireFinder XLS system can use remote transponders for mounting additional modules such as amplifiers without requiring a Person Machine Interface or any control switches. Special doors are available for systems using Model CAB-2 or Model CAB-3 remote transponders. These doors (Models CAB2-XBD and CAB3-XBD) omit the unused inner door, and come complete with ventilation louvers built into the door. Model CAB2-XBD fits into Model CAB2-BB, and Model CAB3- XBD fits into Model CAB3-BB. Model CAB2-XBD and CAB3- XBD are supplied in black. Red versions (Models CAB2-XRD and CAB3-XRD) are also available. Complete box and door kits are available, Models CAB2-X and CAB3-X. 9 ID-MP -> Inner Door Mounting Plate ID-MP Inner Door Mounting Plate The inner door mounting plate (Model ID-MP) is mounted on the inner door of any given model CAB enclosure. Model ID-MP plates are used to mount switch-control modules (Model SCM-8); LED control modules (Model LCM-8), or fan-control modules (Model FCM-6). Four (4) mounting plates are included with each order of Model JD-MP. Each mounting plate has four (4) spaces for control modules, and can hold either four (4) Model SCM-8 modules (one [1] control module space for each module); four (4) LCM-8 (one [1 ]control module space for each module), or two (2) Model FCM-6 modules (two [2] module spaces for each module). FireFinderXLS Components —(cont'd) ID-MP Inner Door Mounting Plate Combinations are also allowed. Blank spaces in Model ID- MP can be covered using the blank-control-module plate (Model BCM). Up to four (4) Model ID-MP modules can be mounted in a single row on the inner door. OD-BP -+ Outer Door Blank Plate OD-BP Outer Door Blank Plate The Outer Door Blank Plate (Model OD-BP) entirely covers an unused row of a XLS system cabinet, and is mounted on the outer door. One (1) blank plate is included with each order of Model OD-BP. ID-SR -* Inner Door Blank Single Plate ID-SP Inner Door, Blank Single Plate The inner door, blank single plate (Model ID-SP) is used to cover any single-module blank spaces within the inner door where no Person Machine Interface or Model ID- MP is being used. Up to four (4) Model ID-SP modules can be mounted in a single row on the inner door. Two (2) blank plates are included with each order of Model ID- SP. BCM -> Blank Control Module Plate BCM Blank Control-Module Plate Model BCM plates can be mounted on a single ID-MP. Four (4) blank module plates are included with each order of Model BCM. OD-LP -+ Outer Door Lens Plate OD-LP Outer Door Lens Plate The Outer Door Lens Plate (Model OD-LP) is a clear plastic lens plate mounted on the outer door of a system cabinet. Model OD-LP is used to allow operators to see the system interface and controls mounted on the inner door, but restricts access to unauthorized users. The plate covers an entire row on the outer door. A single lens plate is included with each order of Model OD-LP. SIEMENS Industry, Inc. Building Technologies Division OD-GP -* Outer Door Grill Plate OD-GP Outer Door Grill Plate The Outer Door Grill Plate (Model OD-GP) also covers an entire row on the outer door of a system cabinet, but has four (4) rows of ventilation louvers on it. Model OD-GP is mounted in front of system bulk amplifiers, card amplifiers, or other modules that generate heat. Using Model OD-GP will permit airflow across these modules to aid in heat dissipation. One (1) grill plate is included with each order of Model OG-GP. Remote System Enclosures Models REMBOX2 and REMBOX4 are FireFinder XLS system enclosures that are used for remotely mounting inner-door modules, such as: Person Machine Interfaces; switch modules (Model SCM series); Live Voice Modules (Model LVM), and Firefighters' Master Telephone (Model FMT) modules. Models REMBOX2 and REMBOX4 are thinner than regular Model CAB-series of enclosures —just 5(12.7cm.) deep overall, and are perfect for mounting in limited-space areas (e.g. - office-complex lobbies or behind a receptionist's desk). No card cages, power supplies or bulk amplifiers can be mounted in a given Model REM BOX-series enclosure due to their smaller depth. However, Person Machine Interfaces and some modules (e.g. - the remote network interface module [Model RNI]; the output control module [Model OCM-16], and the supervised input module [Model SIM-16]) can be mounted in a given Model REMBOX-series enclosure. Due to the depth of Models LVM and FMT, no Model 0CM- 16 or Model SIM-16 modules can be used simultaneously with Model LVM or Model FMT. Model REMBOX2 and Model REMBOX4 are designed for flush mounting with no trim kit required. Both enclosures also come with a clear lens plate on the cover. FireFinder XLS Components - (cont.'d) E l REMBOX2 -+ Two-Module Remote Enclosures REMBOX2 Two Module Remote Enclosures Model REMBOX2 has two (2) inner-door module spaces, and can hold a single Person Machine Interface, up to two (2) switch module brackets and one (1) Model LVM. Combinations are also allowed. Model REMBOX2 can also mount a single RNI remote network interface on a bracket included in the backbox. A. bracket, known as Model REMBOX2-MP, can be used to mount up to four (4) Model 0CM-1 6 output control modules or SIM-i 6 supervised input modules. Model REMBOX2-MP must be purchased separately. Approximate size of Model REMBOX2 is 14-1/2" (36.8cm.i wide, 18-1/2 (47cm.) high and 5' (12.7cm.) deep. REMBOX4 -* Four-Module Remote Enclosures REMBOX4 Four-Module Remote Enclosures Model REMBOX4 has space for mounting four (4) inner-docr modules. Any combination of A Person Machine Interface (two-module spaces); switch module brackets; Model LVM, or Model FMT (one-module space each) can be used. Unused module spaces can be covered with Model ID-SP blank plates. Model REMBOX4 can also mount a single, remote network interface (Model RNI) on a bracket included in the backbox. A bracket known as Model REMBOX4-MP can be used to mount up to eight (8) output control modules (Model 0CM- 16) or supervised input modules (SIM-1 6). Approximate size of Model REMBOX4 is 24' (61 cm.) wide, 18-1/2(47cm.) high and 5' (12.7cm.) deep. Model REMBOX4-MP must be purchased separately. SIEMENS Industry, Inc. Building Technologies Division XLS-MSE2-ADPT - Enclosure Adapter XLS-MSE2/R-ADPT - XLS MSE-2111 Enclosure Adapter Model XLS-MSE2-ADPT, which must be used in conjunction with Model CAB-MP, is an adapter that allows FireFinder XLS cards to be mounted in older-generation MXL Model MSE-2 small black enclosures. Model XLS-MSE2R-ADPT, which must be used in conjunction with Model AB-MP, is an adapter that allows FireFinder XLS cards to be mounted in older-generation MXL Mode MSE-2R small red enclosures. XLS-M ME3-ADPT -> Enclosure Adapters XLS-MME3/R-ADPT - XIS MME-3/11 or MER-2 Enclosure Adapters Moc:el XLS-MME3-ADPT, which must be used in conjunction with Model CAB-MP, is an adapter that allows FireFinder XLS cards to be mounted in older- generation MXL Model MME-3 or Model MBR-2 medium black enclosures. Model XLS-MME3R-ADPT, which must be used in conjunction with Model CAB-MP, is an adapter that allows FireFinder XLS cards to be mounted in 01de-generation MXL Model MME-3R medium red enclosures XLS-MLE6-ADPT Enclosure Adapter XLS-MLE6/R-ADPT - XIS MLE-6111 Enclosure Adapter Model XLS-MLE6-ADPT, which must be used in con Junct on with Model CAB-MP, is an adapter that allcws FireFinder XLS cards to be mounted in older- generation MXL Model MLE-6 large black enclosures. Model XLS-MLE6R-ADPT, which must be used in conjunction with Model CAB-MP, is an adapter that allows FireFinder XLS cards to be mounted in older- generation MXL MLE-6R large red enclosures. FireFinder XLS Corn ponents-(cont.'d) QLJiq XLS-MSE3-ADPT -+ Enclosure Adapters XLS-MSE3/R-ADPT - XLS MSE-3L/R or MSE-3M/R Enclosure Adapters Model XLS-MSE3-ADPT is an adapter that allows FireFinder XLS cards to be mounted in older- generation MXL-IQ Model MSE-3L or Model MSE-3M black enclosure. Model XLS-MSE3R-ADPT is an adapter that allows FireFinder XLS cards to be mounted in older- generation MXL-IQ Model MSE-3LR or Model MSE- 3MR red enclosure. [no XLS-RCC1-ADPT —>Enclosure Adapter XLS-RCC-1-ADPT - XLS RCC-1 Enclosure Adapter Model XLS-RCC1-ADPT is an adapter that allows the FireFinder XLS Model SSDI-C series remote annunciator to be mounted in older-generation Model RCC-1 surface- mount enclosure. XLS-RCC13F-ADPT -4 Enclosure Adapters XLS-RCC1 3FIR-ADPT - XLS RCC-1 FIR or RCC-3 F/R Enclosure Adapters Model XLS-RCC1 3F-ADPT is an adapter that allows the FireFinder XLS Model SSD/-C series remote annunciator to be mounted in older-generation Model RCC-1 F or Model RCC-3F black, flush-mount enclosure. Model XLS-RCC1 3FR-ADPT is an adapter that allows the Model SSD/-C series to be mounted in older-generation RCC-1 FR and RCC-3FR, red flush-mount enclosure. 4P ~ew VPM -* VESDA VESDA-HLI-KIT - VESDA High- Interface Equipment Level Interface Kit SIEMENS Industry, Inc. Building Technologies Division 11 VPM-MP --> VESDA Mounting Plate VPM, VESDA-HLI-KIT and VMP-MP - VESDA Interface Equipment The Very Early Smoke Detection Aspiration (VESDA) Peripheral Module (Model VPM) and the VESDA High- Level Interface Kit (Model VESDAH LI-KIT) are optional FireFinder XLS modules that work in conjunction to provide bi-directional communication between the FireFinder XLS FACP and multiple VESDA detection networks for the following types of VESDA detectors: LaserCOMPACI LaserFOCUS LaserPLUS LaserSCANNER Model VPM allows each FireFinder XLS FACP to annunciate 'Alert,' 'Action,' 'Fire 1,' and 'Fire 2' levels, as well as provide 'faults' from any zone on a connected VESDA network. The VPM Mounting plate (Model VPM-MP) allows mounting one (1) Model VPM and two (2) of Model VESDAHLI-KIT inside a standard FireFinder XLS Model CAB1, Model CA132 or Model CA133 enclosure. Model VPM-MP utilizes two (2) module spaces on a single row of each enclosure. C900V2 -* Dialer-Capture Ethernet Module C900V2 - Dialer-Capture Ethernet Module The Dialer-Capture Ethernet Module (Model C900V2) links the data output of Model MDACT from the FireFinder XLS FACP to an Ethernet connection - on a local-area network (LAN) or wide-area network (WAN) - for communication to a central station over the Internet. Model C900V2 also allows Model MDACT to be optionally linked to the public switched telephone network (PSTN) for communication to a central station over telephone lines. Temperature and Humidity Range FireFinder XLS components are ®UL 864 9th Edition Listed for indoor dry locations within a temperature range of 120+/-3°F (49+/-2°C) to 32+/-30F (0+!- 2°C) and a relative-humidity range of 93+I-2°h at a temperature of 90+/-3°F (32+/-2°C). Details for Ordering Details for Ordering - (continued) Model Part Number Description AC-ADPT 500-633992 Technician Laptop-Power connector BCM 500-033320 Blank control module plate, [four (4) per package] C900V2 S54430-Cl 3-A2 Dialer-Capture Ethernet Module CAB-1 500-633007 Complete Single-Row Cabinet, black CAB-1 R 500-633728 Complete Single-Row Cabinet, red CABi -TK 500-633013 Single-Row Trim-kit Cabinet, black CAB R-TK 500-633729 Single-Row Trim-kit Cabinet, red CAB2-BB 500-633009 (2) Two-Row Back Box, black CAB2-RB 500-634941 (2) Two-Row Back Box, red CAB2-BD 500-633008 (2) Two-Row Inner & Outer Door set, black CAB2-RD 500-633755 (2) Two-Row Inner & Outer Door set, red CAB2-TK 500-633014 (2) Two-Row Trim-kit Cabinet, black CAB2R-TK 500-633753 (2) Two-Row Trim-kit Cabinet, red CAB2-XBD 500-633768 CAB2 Transponder Door CAB2-X 599-034252 Complete CAB2 w/ Transponder Door [no inner door] CAB2-XRD 500-633792 Medium-Enclosure Transponder Door, red [mounts to Model CAB2-RB] CAB3-BB 500-633011 (3) Three-Row Back Box, black CAB3-RB 500-634942 (3) Three-Row Back Box, red CAB3-BD 500-633010 (3) Three-Row Inner & Outer Door set, black CAB3-RD 500-633757 (3) Three-row Inner & Outer Door set, red CAB3-TK 500-633015 (3) Three-Row Trim-kit Cabinet, black CAB3R-TK 500-633754 (3) Three-Row Trim-kit Cabinet, red CAB3-XBD 500-633769 CAB3 Transponder Door CAB3-X 599-034253 Complete CAB3 w/ Transponder Door [no inner door] CAB3-XRD 500-633793 Large-Enclosure Transponder Door, red [mounts to Model CAB3-RB[ CAB-MP 500-633012 Back Box Module Mounting Plate CCL 599-634214 CAN Cable - 21t. (2.1- cm.) Lengthiguired for: scM I LCM/ FCM modules from Models cc-s/ cc-2 Inner Doors and from Row-to-Row on Model CAB-series Inner Doors CC-2 500-633440 Two (2) Slot Card Cage CC-5 500-633037 Five (5) slot Card Cage CDC-4 500-034200 Conventional Detector Card COM-BRK S54430-87-Al Communications Bracket CRC-4 500-033250 Controllable Relay Card CSB 500-033130 CAN Sounder Board OCT-P 500-699291 MDACT Programmer DLC 500-033090 Device Loop Card CM-6 500-033140 Fan-Control-Module Switches [ON, OFF, AUTO] -650066 Software-Upgrade Kit for PMI (vers. 1) to allow global functionality) GPMI-2 S54430-C3-Al Model PMI -2 [with GPMI-HW-KEY[ HCP 500-034860 Intelligent Control Point Module HUM 500-033170 Line-Isolator Module ID-MP 500-633027 Inner-Door Enclosure Mounting Plate, [four (4) per package[ ID-SP 500-633028 Single-Module Inner-Door Enclosure Mounting Plate, [two (2) per package] IIC 500-850328 Interface Isolation Card LCM-8 500-033100 LED Annunciator Module [eight (8) LED sets] MDACT 500-699254 Multi-Point Digital-Alarm Communication Transmitter MLC 554431 -B4-Al MXL Addressable-Device Line Card MOM2-XMP 500-634822 Mounting Plate for Model MOM-2 MOM-2 500-892766 MXL Module Card Cage [one (1) full slot[ Model Part Number Description NIC-C 500-033240 Network Interface Card NRC S54430-A2-Al Network Ring Card: 2nd Generation OD-BP 500-633017 Outer Door Blank Plate OD-BP-R 500-634919 Outer Door Blank Plate, red OD-GP-R 500-634920 Outer Door Grill Plate, red OD-GP 500-633018 Outer Door Grill Plate OD-LP 500-633016 Outer Door Lens Plate PAL-1 500-692407 OUL Listed Parallel Printer - 599-050092 IPMlandGPMI PMI-2 S54430-Cl-Al Person Machine Interface 2 PMI-2-SPAN-LAB S54430-C1O-Al Spanish Overlay for Model PMI-2 PMI-2-PORT-LAB 554430-Cu-Al Portuguese Overlay for Model PMI-2 PMI-2-FRENCH-L S54430-C12-A1 Canadian [French] Overlay for Model PMI-2 PSC-i 2 500-033340 Power supply with battery charger PSX-12 500-034120 Power supply extender [12A @24VDC] PTB 500-033390 Power termination board REMBOX2 500-633772 (2) Two-module remote lobby enclosure, black REMBOX2R 500-650612 (2) Two-module remote lobby enclosure, red REMBOX2-MP 500-634211 Mounting plate for Models OCM-16 / SIM-i 6 in Model REMBOX2 REMBOX4 500-633914 (4) Four-module remote lobby enclosure, black REMBOX4-MP 500-634212 Mounting plate for Models 0CM-1 6/ SIM-16 in Model REMBOX4 REMBOX411 500-650613 (4) Four-module remote lobby enclosure, red RNI 500-033420 Remote network interface module RPM 500-033270 Remote printer module SCM-8 500-033040 Switch module, eight (8) switches SIM-16 500-034060 Supervised input module SSD 500-034740 System-status display SSD-C 500-648733 System-status display with control SSD-INT 500-034740 System-status display with multi-lingual overlays SSD-C-INT 500-034750 System-status display with control and multi-lingual overlays SSD-C-REM 500-634773 System-status display with control for remote lobby enclosure TSP-40A 500-634933 Thermal-strip printer TSP-XB 500-849949 Brackets for thermal-strip printer TSP-XC 500-849950 Cables for thermal-strip printer VPM S54430-F93-A2 VESDA Peripheral Module VPM-MP 554430-F95-A2 Mounting Plate for VESDA Peripheral Module VESDA-HU-KIT 554430-F99-A2 VESDA High-Level Interface Kit XL5-MLE6-ADPT S54430-C9-Ai MLE-6 enclosure adapter for XLS, black XLS-MLE6R-ADPT 554430-C9-A2 MLE-611 enclosure adapter for XLS, red XLS-MME3-ADPT S54430-C8-A1 MME-3 and MBR-2 enclosure adapters for FireFinder XLS, black XLS-MME3R-ADPT S54430-C8-A2 MME-3R enclosure adapter for XLS, red XLS-MSE2-ADPT S54430-C7-Al MSE-2 enclosure adapter for XLS, black XLS-MSE2R-ADPT S54430-C7-A2 MSE-2R enclosure adapter for XLS, red XLS-MSE3-ADPT 554430-C14-Au MXL-IQ MSE-3L and MSE-3M enclosure adapters for XLS, black XLS-MsE3R-Aopr 554430-C14-A2 MXL-iQ MSE-3LR & MSE-3MR enclosure adapters for XLS, red XLS-RCCi-ADPT S54430-Z14-Al RCC-i enclosure adapter for XLS-SSD, black xLs-Rcc13F-ADPT S54430-Zi3-A1 RCC-1F & RCC-3F enclosure adapters, black XLS-Rcc13FR-ADP S54430-Zi3-A2 RCC-1FR & RCC-3FR enclosure adapters, red ZIC-2C 500-648671 (2) Two-channel adapter card, via (Model ZIC-88) ZIC-4A 500-033050 (4) Four-circuit zone indicating card ZIC-8B 1 500-648670 (8) Eight-circuit zone indicating card Notice: This marketing data sheet is not intended to te used for system design or installation purposes. For the most up-to-date information, refer to aach product's installation instructions. Fire Safety Fire Safety 8 Fernwood Road 1577 North Service Road SIEMENS Industry, Inc. Florham Park, NJ 07932 East Oakville, Ontario April 2015 Building Technologies Division Tel: (973) 593-2600 (sll-FS) L6H 0H6 / Canada Supersedes sheet dated 1/2015 FAX: (908) 547-6877 Printed in USA. Tel: [905] 465-8000 (Rev. 15) URL: www.usa.Siemens.com/Fire URL: www.Siemens.CA Catalog Sheet SIEMENS Fire Safety & Security Products FireFinder XLS Card Cage-5 Slots Model CC-5 ARCHITECT AND ENGINEER SP ECIFICATIIONS 'Common card cage for all FireFinder XLS / V option cards Five (5) slots to mount any option cards - with no restrictions Mounts on back box or CAB-MP (two-module spaces) Removable terminal blocks Numbered terminal blocks All field-wiring terminations on top (power limited) All internal-wiring terminations on bottom (non-power limited) Molded card guides for card mounting Card-position locator label on card guide All cards communicate via common 60-pin power! data bus Screw terminals wire sizes supported: 12 AWG - 24AWG DIN connectors ®UL 864 9th Edition Listed and QULC Listed; FM, CSFM & NYMEA Approved Product Overview The Model CC-5 card cage provides the physical mounting location and all wiring connection points for all fire and voice system options cards for the FireFinder XLS system. Specifications All cards plugged into the Model CC-5 card cage communicate with other modules of the FireFinder XLS panel — via a common, 60-pin data bus. This 60-pin bus runs through the card cage; making all communication data buses and signals available to all cards. Connectors are provided on the left and right side of Model CC-5 to connect a 60-pin cable for communications with the FireFinder XLS operator interface, power supplies and amplifiers modules. There are no active components on Model CC-5. Field wiring to all devices and circuits terminates at the Model CC-5 card cage. All cards designed for use with Model CC-5 route their field wiring terminations to the 'top' of Model CC-5 - these connections are all power limited. Internal wiring connections distribute 24VDC to cards or high-level audio signals (depending on application used) connected to the "bottom" of Model CC-5 - these connections are all non-power limited. All wiring connections to Model CC-5 are made to removable terminal blocks. Terminal blocks are rated for use with wire-sized 1 2AWG to 24AWG. Each terminal block comes with a protective cover that also serves as a handle to allow easy terminal-block removal when wires are connected. FireFinder XLS 6320 SIEMENS Industry, Inc. Building Technologies Division Specifications - (continued) Each connector is numbered to make wiring terminations to the correct position on the terminal block simple and reduce the potential for wiring errors. Model CC-5 is shipped with two (2) card guides (top and bottom) that mount to the Model CC-5 PCB. The 'top' card guide contains a blank label for use by the installer to indicate the location or card-slot position. The blank label serves as a reminder to the installer to ensure the proper card goes in the correct card slot - this is important during commissioning when cards may be installed after the field- wiring terminations have been made - and when cards are removed for service. All field-wiring terminations are typically made to the Model CC-5 terminal blocks before the card guides are mounted and the option cards are installed. Model CC-5 mounts in two (2) of the four (4) available module spaces directly on the back box or optional Model CAB-MP for installation in the CAB-1, CAB-2 or CAB-3 enclosures. Compatible FireFinder XLS Cards Any combination of the following (5) option cards can be installed in the CC-5: Fire System Cards: Model No. Part No. Description DIC 500-033090 Device Loop Card ZIC-4A 500-033050 Zone Indicating Card 4 Circuits CRC-6 500.033250 1 Controllable Relay Card NIC-C 500.033240 4Con,entional Network Interface Card CDC-4 500-034200 Detector Card Voice System Cards: Model No. Part No. Description DAC-NET 500.035100 Digital Audio Card-Network AIC 500.035300 Audio Input Card ZAC-40 500-035400 40-Watt Zone Amplifier Card TZC-813 500-034110 1 Telephone Zone Card Details for Ordering Model No. Part No. Description CC-5 500-633037 Card Cage 5 Slots Refer to Installation Instruction: 315-033035 Temperature and Humidity Range Products are ®UL 864 9th Edition listed for indoor dry locations within a temperature range of 120+/-3'F (49+1-2°C) to 32+/-3°F (0+/-2°C) and at a relative humidity of 93+/-2% at a temperature of 90+/-3°F (32+/-2°C). Notice: This marketing catalog sheet is not intended to be used for system design or installation purposes. For the most up-to-date information, refer to each product's installation instructions. Fire Safety Fire Safety 8 Fernwood Road 2 Kenview Boulevard SIEMENS Industry, Inc. Florham Park, NJ 07932 Brampton, Ontario Building Technologies Division Tel: (973) 593-2600 sri L6T 5E4 / Canada May 2010 Supersedes sheet dated 7/09 FAX: (908) 547-6877 Printed in U.S.A. Tel: (905) 7999937 (Rev. 2( URL: www.SBT.Siemens.com/FlS FAX: (905) 799-9858 Catalog Sheet SIEMENS Fire Safety & Security Products FireFinder XLS Network Interface Card Model NIC-C ARCHITECT AND ENGINEER SPECIFICATIONS HNET communications XNET communications CAN network communications Supports Class B - Style 4 or Class A - Style 7 wiring for XNET or HNET Supervises the HNET or XNET and CAN networks Diagnostic LEDs Isolates short circuit faults Ground-fault detection Network repeater Downloadable firmware UL 9th Edition Listed &ULC Listed; FM, CSFM and NYMEA Approved Product Overview The Network Interface Card (Model NIC-C) provides HNET or XNET network communications between enclosures. In addition to the HNET or XNET communication, Model NIC-C provides CAN network communication within an enclosure or external to the enclosure. The HNET or XNET can be wired Class B - Style 4 or Class A - Style 7, but the CAN network can only be wired Class B - Style 4. Specifications A single Model NIC-C can provide either HNET or XNET communications. The CAN interface is available regardless of the HNET or XNET usage. When Model NIC-C is used for HNET communications, Model NIC-C provides communication between enclosures within a single system. The maximum HNET Model NIC-C cards on a single system (single node) is 50. Model NlC-C supervises the HNET network to insure proper operation. Model NIC-C also isolates a short-circuit fault to each individual segment of the HNET network. Model NIC-C provides an electrical repeater for each HNET pair. Model N IC-C (Front View) Model NIC-C (Side View) When Model NIC-C is used for XNET communications, Model NIC-C provides communication between systems. The maximum XNET Model NIC-C cards on a single system (single node) is one (1) - for a total of (59) XNET Model N IC-C cards on a peer-to-peer, networked system. The XNET Model NIC-C card must reside in the same enclosure as the Person Machine Interface (Model PMI). Model NIC-C supervises the XNET network to ensure proper operation. Model NIC-C also isolates a short-circuit fault to each individual segment of the XNET network. Model NIC-C provides an electrical repeater for each XNET pair. MXL systems may also reside on the same XNET with FireFinder XLS systems. The FireFinder XLS will also report all events over the XNET to the Network Command Center for display. Events are displayed on Model NCC-G: Trouble, Acknowledge, Alarm-Silence and System-Reset commands are also initiated at Model NCC. Model NCC can also be used to perform maintenance commands on an individual Fire Finder XLS on the XNET. FireFinder XLS 6338 SIEMENS Industry, Inc. Building Technologies Division Specifications - (continued) The NIC-C Card takes one card slot and mounts in CC-2 or CC-5 Card cage inside a CAB-1, CAB-2, or CAB-3 Enclosure. The NIC-C provides the CAN network which supports the LCM-8 I SCM-8 I FCM-6 I 0CM-1 6 I SlM-1 6 CAN modules. Up to (99) CAN module addresses are available per enclosure. The NIC-C Card has diagnostic LEDs that indicate Card Fail, CAN Fail, HNET Fail, XNET Fa I, Grourd Fault, Loop-A Fail and Loop-13 Fail, as well as LEDs, to indicate Power, Style and Active Networks. Details for Ordering iiiFi unkr FN Number part . Decriplioi IC-c -zo Networi FnIerae Card Temperature and Humidity Range Products are ®UL 864 9th Edition listed for indoor dry locations within a temperature range of 120+/-3°F (49+/-2°C) to 32+/-30F (0+1-2°C) and at a relative humidity of 9342% at a temperature of 90+1-3°F (32+/-2°C). Electrical Ratings InpiA PcMrer I Output Power 24V Back PIae C*tE%t 12isA [ €ac rsxr And CAN Net.wcck Pair Scwi TeffT*W 24V Current 0 7&M dIIig msg !*.On) 6.2V Back P*ae Cwrst U 24V Standby Current 12rA Notice: This marketing catalog sheet is not intended o be used for system design or installation purposes. For the most up-to-date irformation, refer to each product's installation instructions. Fire Safety Fire Safety 8 FernwDod Rcac 2 Kenview Boulevard SIEMENS Industry, Inc. Florham Park, 4J1079:32 Brampton, Ontario Building Technologies Division Tel: (973) 593-2600 (Sill L6T 5E4 I Canada FAX: (998) 547-6377 Printed in U.S.A. Tel: (905) 799-9937 uRL: www.SBT.Semens.com/FIS FAX: (905) 799-9858 May 2010 Supersedes sheet dated 7/59 (Rev. 2) Im- SIEMENS Data Sheet Fire Safety & Security Products FireFinder® XLS MXL Line Card Model MLC ARCHITECT AND ENGINEER SPECIFICATION Alarm, Trouble, Supervisory, Security and Status reporting Two (2) intelligent analog device circuits 60 intelligent devices per circuit Accepts remote conventional-zone modules Degrade mode Supports audible bases On-board microprocessor On-Board, ground-fault detection Programmable Input/Output module Short-circuit isolation with Model LIM-1 Remote smoke-detector-sensitivity adjustor Independent control of detector relays Up to 60 relays per circuit Intelligent contact monitoring devices 'Class B' (Style 4) or 'Class A' (Style 6) wiring position Supports T-Tap wiring for 'Class B' circuits ®UL 864 9th Edition Listed; CSFM Approved Product Overview The MXL Line Card (Model MLC) is an optional card for the FireFinder XLS fire alarm control panel (FACP) that supplies two (2) intelligent analog circuits, utilizing the Model 'I '-series; Model 'ID '-series; Model 'IL '-series or Model ' FP '-series type intelligent devices. Specifications - (continued) Sensitivity of certain smoke detectors can be queried and adjusted at the FireFinder XLS control panel. Further, sensitivity I obscuration, as well - as other device information - can be displayed and printed at the FireFinder XLS. Model MLC occupies two (2) addresses on the HNET Model MLC supports the use of relay bases and audible bases network, and - through the use of a unique (independently controllable). To provide analog-loop, short- communications protocol - devices connected circuit isolation, the Model LIM-1 module can be used to to the Model MLC circuits are dynamically prevent a single short circuit from interrupting loop-device supervised by FireFinder XLS. communication. Smoke detectors are monitored for sensitivity I obscuration, and notification is given when the sensitivity / obscuration is outside normal parameters. Specifications Each of the Model MLC circuits supports the use of up to 60 Alarm; Trouble; security; status, and supervisory-type devices. Further, remote conventional initiating-device zone modules (Model CZM-1 B6); intelligent monitoring devices (Model TRI), and intelligent control points (Model ICP-B6) are also supported by Model MLC circuits. Each Model MLC circuit can be wired in either a 'Class B' (Style 4) or 'Class A' (Style 6) configuration. When using the (Style 4) method, T-Tap wiring is permitted with no loss of supervision. Model MLC has an on-board microprocessor, which provides the ability to function in a degrade mode and initiate alarm conditions, even if the FireFinder XLS main central- processing unit (CPU) fails. Model MLC plugs into one (1) card slot in the Model CC-5 or Model CC-2 card cage. MXL Line Card for FireFinder XLS 6354 SIEMENS Industry, Inc. Building Technologies Division Temperature and Humidity Range Model MLC is ®UL 864 9th Edition -it-=d for indoor dry locations within a temperaturE range of 120+/-3°F (49+/-2°C) to 32+1-3°F (o+/-2°C) and a relative humidity of 93+1-2% at a temperature of 90+1-3°F (32+1-20C). Related Documentation ~ Product Data Sheet Number Fi,eflr-der XLS Overview 6300 Details for Ordering Model Part I Description Number Number MLC S54L31134-A1 MXL Addressable Line Card for FfreFinder XLS Notice: This mark2tino data sheet is not intended to be used for system design or installation purposes. For the most pto-date information, refer to each product's installation instructions. Fire Safety Fire Safety F Fernwood Road 2 Kenview Boulevard SIEMENS Industry, Inc. Florham Park, NJ 07932 Brampton, Ontario August 2012 Building Technologies Divisior Tel. (973) 593-2600 lSiI-FS L6T 5E4 I Canada Supersedes sheet dated 2112 FAX: (908) 547-6877 Frinted in U.S.A. Tel: (905) 799-9937 (Rev. 2) WRL www.usa.Siemensccm/Fire FAX: (905) 799-9858 Li LL [Front View] [side View] SIEMENS Data Sheet Fire Safety & Security Products FireFinder® XLS Device Loop Card Model DLC ARCHITECT AND ENGINEER SPECIFICATIONS Quantity 252 addressable points I Provides two (2) intelligent addressable circuits Compatible with 'H'-series, DesigoTM Fire Safety-series and CerberusTM PRO-series of intelligent detectors Multi-criteria / Carbon Monoxide (CO) Detector with ASAtechnoiogyTh - Multi-criteria Detector Multi-criteria Detector with ASAtechnology Photoelectric Smoke detector Quad Interface module Thermal (Heat) detector Polarity insensitive via Surefterm technology Quantity 12 diagnostic light-emitting diodes (LEDs) for easy circuit diagnosis Supports 1-Tapping Onboard, ground-fault detection and short-circuit isolation Onboard microprocessor for dependable, efficient device communication Degrade mode Supports 'Class B' or 'Class A' wiring ®UL 864 9th Edition Listed & OULC Listed; FM, CSFM, & NYC Fire Department Approved Product Overview The Device Loop Card (Model DLC) is the interface used for connection of Desigo and Cerberus PRO intelligent detectors and initiating devices to a single FireFinder XLS fire-alarm control panel (FACP). Model DLC also can work with Siemens input devices, manual stations and control devices. Each Model DLC plugs into one (1) slot of the Model CC-2 or Model CC-5 card cage. Programming for Model DLC is accomplished via the XLS FACP custom-configuration tool, Zeus. Model DLC takes one (1) address on the network, communicating up to a total 252 detectors and devices. Model DLC has 12 LEDs for diagnostic purposes, and provides ground-fault detection and zone-isolation circuitry. Specifications Model DLC initializes, operates and maintains all devices residing on its two (2) circuits. Model DLC communicates all relevant device and event information (Alarm, Trouble and Supervisory commands) to FireFinder XLS, and supervises the device loop circuit. Model DLC is polarity insensitive via Sure Wire technology, which greatly reduces commissioning time normally spent tracing down crossed-field wiring. Model DLC communicates detector information, such as sensitivity of intelligent fire detectors and logic-function data, to the Person Machine Interface, which is located within the FireFinder XLS system. Each device loop card supports two (2), isolated circuits up to a total of 252 addressable devices - as well as relay and audible bases, remote lamps and duct-detector housings in any combination. The microprocessor controls the onboard isolation in case there is a short in any of the circuits, thus allowing the other circuit to continue operating. For continuous protection, the on- board microprocessor continues to operate even in the event of a XLS CPU failure. Device Loop Card 6312 SIEMENS Industry, Inc. Building Technologies Division Temperature and Humidity Range The Device Loop Card is €UL 864 9th Edition Lis:ed for indoor dry locations within a temperature range of 1 20+1-3°F (49+/-2°C) to 32+/-30F (0+/-2°C) ard a relative humidity of 93+/-2% at a temperature cf 90+/-3°F (32+/-20C). Electrical Ratings 24V Current Draw: [Backplane] 24V Current Draw: 100mA+ 1.4mA [Screw Terminal] per device 24V Current Draw: 145mA+ 1.8mA [Standby] per device 6.2V Current Draw: [Backplane] 200mA Device Loop Draw: 375mA, max. [at 30VDC, max] [power limited) Details for Ordering - Desigo Series - Model Part Number Number Description FDC10422 S54322-F4-A1 Quad Interface Module FDOT421 554320-F6-A1 Addressable Multi-criteria Detector FD0421 554320-F4-A1 Photoelectric Smoke Detector FDT421 554320-F5-A1 Thermal (Heat) Detector FDOOTC441 554320-F8-A1 Multi-criteria Fire! CO Detector wi ASAtechnology FDOOT441 S54320-F7-A1 Multi-criteria Fire Detector w! ASAtechnology Details for Ordering - (continued) 'H'-Series - Model Number Part Number Description HFP-1 1 500-033290 FirePrint Detector HFPT-1 1 500-033380 Thermal Detector HMS-D 500-033400 Dual-Action Manual Station HMS-M 500-033450 Manual Station, Metal HMS-S 500-033200 Single-Action Manual Station HMS-SA 500-034150 Single-Action Manual Station (Auxiliary contact), [Canada only] HMS-25 500-033460 Two-Stage Manual Station [Canada only] HTRI-D 500-033360 Dual-Input Module HTRJ-M 500-034000 Mini-Input Module HTRI-R 500-033300 Single-Input w/ Relay HTRI-S 500-033370 Single-Input Module - Cerberus PRO Series - Model Part Number Number Description FDCI0422 554322-F4-A1 Quad Interface Module H1921 554320-F5-A2 Thermal (Heat) Detector 0H921 554320-F6-A2 Addressable Multi-criteria Detector 0P921 554320-F4-A2 Photoelectric Smoke Detector OOHC941 554320-F8-A2 Multi-criteria Fire ! CO Detector w! ASAtechnology 00H941 554320-F7-A2 Multi-criteria Fire Detector w! ASAtechnology -Other Modules and Devices Model Number Part Number Description ILED-HC 500-048637 Intelligent Remote Lamp, ceiling Mount ILED-HW 500-048809 Intelligent Remote Lamp, Wall Mount DLC 500-033090 Device Loop Card PMI 1500-0330701 Operator Interface! System CPU PMI-2 S54430-Cl-Al I Person Machine Interface 2 Notice: This marketing data sheet is not n:eided to be used for system design or installation purposes. For the most up-to-date informaticn. refer to each product's installation instructions. Fire Safety Fire Safety 8 Fernwood Road 2 Kenview Boulevard SIEMENS Industry, Inc. Florham Park, N 07932 Brampton, Ontario Building Technologies Division Tel: (973) 593-2&3&(511) L6T 5E4 I Canada May 2013 FAX: (908) 547-8877 Printed in U.S.A. Tel: (905) 799-9937 Supersedes sheet dated 5/10 (Rev. 3) URL: www.USA.ieme-ns.com/Fire FAX: (905) 799-9858 ZIC-2C ZIC-8B ZIC-8B Side View Front View (with ZIC-2C mounted) Pc SIEMENS Catalog Sheet Fire Safety & Security Products FireFinder XLS Zone-Indicating Cards Model ZIC-813 (with mounted Model ZIC-2C) ARCHITECT AND ENGINEER SPECIFICATIONS Operates audible or visual notification appliances (NACs) Three (3) unique signals from each circuit Operates 25V or 70VRMS audio speakers One (1) or (2) two-channel voice operation Eight (8) Class-B (StyleY) Circuits 24 VDC 2.0 Amps per circuit Fully programmable Coded audibles available Built-in strobe synchronization March time I Uniform Code 3 Selectable degrade operation Silenceable I non-silenceable option Automatic/ manual control On-board microprocessor Built-in, Ground-Fault Detection Circuits power limited, per NEC 760 ®UL 864 9th Edition Listed & ®ULC Listed; FM, CSFM & NYMEA Approved Product Overview The Zone-Indicating Card (Model ZIC-813) provides eight (8) fully-supervised, programmable output circuits for use on the FireFinder XLS Fire Alarm Control Panel. Model ZIC-813 supplies four (4) Class-13 type (Style Y) output circuits; power limited to 2.0 amps maximum per circuit. Each circuit can be independently programmed for use with listed audible or visual notification appliances, or listed emergency-audio speakers. Model ZIC-813 plugs into one (1) slot in the CC-5 or CC- 2 Card Cage, and has on-board LEDs for system status and troubleshooting. Model ZIC-2C mounts directly onto Model ZIC-813, and allows each of the Model ZlC-813 output circuits to be used for (2) two-channel voice applications. Indication of power, communication, internal operation, and ground-fault conditions are provided, as well as indication of circuit activation or trouble conditions. All system status conditions are also reported to the system Person-Machine Interface (PMI). Each circuit or output may be controlled automatically with system logic programmed with the ZEUS Programming Tool, or manually, by using the FireFinder XLS keypad on the PMI. Automatic control may also be time based. Each circuit or output can be manually 'Armed' or 'Disarmed' through the PMI keypad. FireFinder XLS 6343 SIEMENS Industry, Inc. Building Technologies Division Controls and Indicators RESET switch - Re-initialize; the ZIC-813 card only POWER LED - Indicates power is applied to ZlC-813 CARD FAIL LED - Illuminates when the card microprocessor has failed HNET FAIL LED- Illuminates when the HNET communication fails, and the ZIC.-8B is in degrade mode GND FAULT LED - Indicates The detection of a ground- fault condition (either negative or positive) on the ZIC-8B field wiring ZONE ACTIVE LEDs - Illumirates to indicate that the zone has been activated either automatically or manually. There is one LED for each zone. TROUBLE LEDs - Indicates the presence of a trouble condition (either an open circuit or a short circuit) on the zone. There is one LED for each zone. Electrical Ratings (Model ZIC-2C) 17mA Per active output 24V Back Plane DmA CLuent (ZIC.-8B SI in 'BP POWER position) (ZIC-85 S1 in "EXT POWER' position), 17rnA Per active output 24V Screw DnA Terminal Cizrent (ZIC-85 Si in 'EXT POWER" position) (ZIC.-8B SI in 'BP POWER" position) 6.2V Back Plane Current DnA 24V Standby Current DnA Electrical Ratings (Model ZIC-813) 24VBactk Plane or External Power Current 'See NOTE below' " Sciw Tenmlnai 24V CuTert Total Devios Curient 6.2V Back Plaw Currert 0 24V Standby CurrentIr 105iM Note: The 24V current is dependent on the usage and wiring type of each ZICcircuil. Listed below in the Iefthand column of the next page are the required current draws tor each zo ne's :J5age and Wiring type: Product Overview - Continued When any circuit or output has been 'Disarmed,' the PMI display shall indicate the affected circuit or output, and the 'Partial-System Disable' LED will illuminate, until the circuit or output has been returned to the 'Armed' condition. Model ZlC-BB circuits can also be manually energized or de- energized when in the 'Disarmed' state, via use of the PMI. Model ZIC-8B contains an on-board microprocessor, which allows notification-circuit outputs to function in a degrade mode; even if the main FireFinderXLS processor or the local-network-communication lirk ha5 failed. In a degrade mode, Model ZlC-8B will respona to an Alarm or Trouble from any intelligent, addressable-initiating device or conventional-zone- initiating device connected in the same local enclosure. Standard NAC Zone - Each of the eight (8) circuits on Model ZlC-8B can be configured for use as a standard NAC. The NAC output can be used as a steady, coded, horn / strobe synchronized, horn I strobe synchronized with silence-able horn, stroDe synchronized, or unsynchronized strobe output. The available coding includes ANSI Temporal, March Time 120 pulse per minute (PPM), March Time 60 PPM March Time 30 PPM, Canadian Two-stage 30 PPM, Canadian Two-stage 120 PPM and custom coding. Using the horn / strobe synchronized setting for the outputs allows Siemens horns, strobes and horn I strobes to synchronize all horns in a temporal pattern. The horn I strobe synchronized setting for the outputs also allow all strobes to flash simultaneously. The silenceable setting shall allow the operator to silence the horns, while keeping the strobes active. Outputs may be programmed through logic to trE nsmit - up to three (3) different signal types - dependng on event priority. For instance, the same circuit can be programmed to transmit the ANSI Temporal pattern for evacuation, March Time 120 PPM for tornado notification, and a custom code for recall. Standard Speaker Zone - Each of the eight (8) circuits on Model ZIC-8B can be configured for use as a standard-speaker circuit in single or dual-channel systems. Dual-channel operation requires the optiona ZIC-2C module, which is mounted to a connectcr directly on the ZIC-8B. No additional mounting space' is required for the ZIC-2C. The ZIC-813 can be used with the ZAM-80/1 80 bulk amplifier or the ZAC-40 amplifier card. ZlC-8B is limited to 25 watts max. I zone at 25V (when the zone is active.) At 70V, ZIC- 8B is limited to 30 watts max. / zone. SIEMENS Industry, Inc. Building Technologies Division Electrical Ratings - (continued) Details for Ordering ZiC8B Current Recuirrnent PrOIut t'-'Zon'e Zono Usage OutpLit Current Requireawnt Not Used U NAC 17TrA $trobs-$)flc 17iM $Vcft -umm 17n $paaker Znno 2 O 34n Speaker Zone - I th. I7n NAC -oded I7mA m48 8ndty Qureid -9ImA Model Number Part I Number I I Description ZIC-8B 500-648670 (8) Eight-circuit Zone Indicating Card ZIC-2C 500-648671 (2) Two-channel Adapter Card Temperature and Humidity Range Products are ®UL 864 91h Edition listed for indoor dry locations within a temperature range of 120+/-3°F (49+/-2°C) to 32+/-3°F (0+/-2°C) and at a relative humidity of 93+/-2°k at a temperature of 90+/-3°F (32+/-20C). SIEMENS Industry, Inc. Building Technologies Division Notice: This marketing catalog sheet is not intended to be used for system design or installation purposes. For the most up-to-date information, refer to each product's installation instructions. Fire Safety Fire Safety 8 Fernwood Road 2 Kenview Boulevard SIEMENS InJistry, Inc. Florham Park, NJ 07932 Brampton, Ontario Building Technologies Division Tel: (973) 593-2600 S11 L6T5E4/Canada April 2010 FAX: (908)547-6877 Printecinu..A. Tel: (905) 7999937 Supersedes sheet datec 110 1RL: www.SBT.Siemens..on/FIS FAX: (905) 799-9858 (Rev. 3) SIEMENS Catalog Sheet Fire Safety & Security Products FireFinder XLS System-Status Display Series Models SSD, SSD-C and SSD-C-REM ARCHITECT AND ENGINEER SPECIFICATIONS 4 x 40" backlit LCD screen Event and audible status LEDs Scroll buttons to view additional events Local sounder Supports Style 4 or Style 7 wiring Built-in transient protection Mounts in its own enclosure or REM BOX Optional local-system control Downloadable firmware OUL 864 9th Edition Listed and €ULC Listed; FM, CSFM & NYMEA Approved SSD SSD-C with Control Product Overview The System-Status Display (SSD Series) is a remote LED / LCD display that shows the local status of a FireFinder XLS system. A LED will illuminate when Alarm, Supervisory, Trouble and Security events occur on the system. A four-line LCD will give details of the event in alphanumeric form. The display can be toggled to display additional events. Optional remote-system control capabilities are available. Specifications The SSD Series display has separate LEDs for Alarm, Supervisory, Trouble and Security events on the FireFinder XLS system. Each LED will flash when unacknowledged events of that type are present on the system. The LED will change to steady, upon acknowledgment of the event. Also, there are two (2) LEDs that indicate the state of audible circuits on the system: one (1) LED to indicate that the circuits are active and one (1) LED to indicate the circuits have been silenced. The LCD display on the SSD Series display has four (4) rows —40 characters for each row. When the FireFinder XLS system is in its normal supervisory state with no events present, the display will annunciate the system ID information, the date and the time of day. When an event occurs on the system, the LCD display will show the event type and address, the time of the event, the custom message for that address, the usage of the device, and whether the event is acknowledged or not. Additionally, the display will show the total number of all types of events present on the system. The display has a backlight feature that operates upon receiving any event information or when any operator buttons are pressed. A local sounder is included with the SSD Series display that operates when any events are displayed on the system. The sounder can be optionally disabled through software programming. Pressing any operator buttons will silence the local sounder when an event is present. FireFinder XLS 6326 SIEMENS Industry, Inc. Ruildina Technoloales Division Specifications - (continued) The SSD Series display has two (2) display-control buttons that are used to display the next or the previous event information in the sequence, and a local sounder silence button. Programming for the SSD Series display is done with the Zeus programming tool. Models SSD-C and Model SSD-C-REM have three (3) additional control buttons for acknowledging events, silencing audible circuits, and resetting the system. Model SSD-C has an integral key switch that enables these control buttons to operate. Model SSD-C-REM is located within a locked cabinet, so no additional key switch is required for enabling the control buttons. The SSD Series display is remotely connected to the H-Net communication bus from any Model NIC-C interface in a FireFinder XLS system enclosure using Class B, Style 4 or Class A, Style 7 wiring. 24VDC is required to run the SSD Series display, and can be provided from a Model PSC-1 2 Power Supply or PSX-1 2 Power Supply Extender in the FireFinder XLS system enclosure. Power from other UL Listed 24VDC power sources is also acceptable. The SSD Series display has screw terminals capable of supporting 12 to 22-gage wires. The H-Net communication from the FireFinder XLS system can be terminated on the SSD Series display, or may pass through for communication with other modules. Diagnostic LEDs on the SSD Series display indicate power and communication status. Models SSD and SSD-C can be mounted in a (2) two-gang electrical box or a (4) four-inch square electrical box. No flush-trim kit is required. The unit is approximately 10-1I2"(26.7cm.) wide, 6-1/8" (1 5.2cm.) high, and 1-1/2" (3.8cm.) deep. The Model SSD-C-REM is mounted in a Model REM BOX2 or Model REM BOX4 Remote Lobby Enclosure, or any CAB enclosure inner door. Model SSD-C-REM requires two (2) module spaces in the remote lobby enclosure, and its bracket supports the mounting of four (4) inner door modules (such as Model SCM-8 or Model LCM-8 modules) below the display. The inner door module spaces are arranged in two (2) rows of (2) two-module spaces. Products are OUL 864 9th Edition listed for indoor dry locations within a temperature range of 120+1-3°F (49+1-2°C) to 32+/-3°F (0+1-2°C) and at a relative humidity of 93+1-2% at a temperature of 90+1-3°F (32+1-2°C). Details for Ordering Model Number Part Number Description SSD 500-034170 System-Status Display SSD-C 500-648733 System-status Display [with control] SSD-C-REM 500-634773 System-Status Display [with control for remote-lobby enclosure] REMBOX2 500-633772 Small Remote-Lobby Enclosure REMBOX4 500-633914 Large Remote-Lobby Enclosure BCM 500-033320 Blank Control Module Plate Electrical Ratings SSD -C Typical 200mA(rnax) at 24VDC 24VDC (Nominal) Input Voltage (31VDC max) filtered Notes: An auxiliary-regulated, power-limited power supply may be used to provide power to Model SSD. The power supply must betuL Listed for Fire-Protect on signaling Application. Be sure to also include Model 55D-C in the battery calculations. SSD SSD -INTL Typical 200mA (max) at 24VDC 24VDC (Nominal) Input Voltage (31VDC max) filtered Notes: An auxiliary-regulated, power-limited power supply maybe used to provide power to Model SSD. The power supply must be IUL Listed for Fire- Protection Sgnaling Application. SSD- C-REM Typical 200mA(max) at 24VDC 24VDC (Nominal) Input Voltage (3IVDC max) filtered Notes: An auxiliary-regulated, power-limited power supply may be used to provide power to Model SSD-C-REM. The power supply must be 04JL / @ULC approved for Fire Protection Signaling Application. Be sure to also include Model SSD-C-REM in the battery calculations. Notice: This marketing catalog sheet is not intended to be used for system design or installation purposes. For the most up-to-date information, refer to each product's installation instructions. Fire Safety Fire Safety 8 Fernwood Road 2 Kenview Boulevard SIEMENS Industry, Inc. Florham Park, NJ 07932 Brampton, Ontario August 2010 Building Technologies Division Tel: (973)593-2600 SIll L6T5E4fCanada FAX: (908) 547-6877 Printed in U.S.A. Tel: (905) 7999937 Supersedes sheet dated 5/10 (Rev. 3) 1 JR1 www .1;RT R(,umpns nmIrl PAY (Qfl) 700-QRcR