Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
6515 AMBROSIA LN; ; FA160042; Permit
9/27/22,11:35 AM FA160042 Permit Data City of Carlsbad Fire Alarm Permit Job Address: 6515 AMBROSIA LN Permit Type: FALARM Parcel No: 2158410700 Lot #: 0 Reference No.: Permit No: FA160042 Status: ISSUED Applied 8/8/2016 Approved: 8/8/2016 Issued: 8/8/2016 PC #: Inspector: Project Title: DAYBREAK CHURCH WORSHIP CENTER INSTALL NEW ADDRESSABLE FIRE ALARM WITH EMERGENCY VOICE EVACUATION SYSTEM CONSISTING OF THE EQUIPMENT SHOWN ON DEVICE LEGEND ON PLANS. Applicant: JJJ ENTERPRISES 533 S VINEWOOD ST ESCONDIDO CA 760-747-3050 Owner: DAYBREAK COMMUNITY CHURCH OF COASTAL NORTH COUNT 6515 AMBROSIA LN CARLSBAD CA / Fees ($) Add'l Fees ($) Total ($) Balance ($) 639.5 0 639.5 0 11 about:blank 1/1 mrNFIRP EHUEP'1PN21E'% FIRE ALARM - SECURITY - LOW VOLTAGE SYSTEMS Daybreak Church Worship Center 6515 Ambrosia Lane Carlsbad, CA 92011 FIRE ALARM SYSTEM MATERIAL DATA SHEETS FAI 60042 6515 AMBROSIA LN FIRE ALARM SYSTEM BILL OF MATERIALS NOTIFIER FIREWARDEN-100-3 ADDRESSABLE FIRE ALARM CONTROL PANEL CSFM# 7165-0028:0235 NOTIFIER NFC-50/100: 50 WATT, 25 VRMS EMERGENCY VOICE EVACUATION CONTROL PANEL CSFM# 6911-0028:0265 NOTIFIER N-ANN-80 REMOTE FIRE ALRM ANNUNCIATOR CSFM# 7120-0028:0240 DMP COMMERCIAL FIRE COMMUNICATOR CSFM# 7300-1157:0136 NOTIFIER NP-100 ADDRESSABLE SMOKE DETECTOR CSFM# 7272-0028:0231 NOTIFIER NOT-BG-12LX MANUAL PULL STATION CSFM# 7150-0028:0199 NOTIFIER NC-100 ADDRESSABLE RELAY MODULE CSFM# 7300-0028:0230 NOTIFIER NMM-100P ADDRESSABLE MINI MODULE CSFM# 7300-0028:0230 SYSTEM SENSOR SPSCW CEILING MOUNTED SPEAKER STROBES CSFM# 7320-1653:0201 SYSTEM SENSOR SPSR WALL MOUNTED SPEAKER STROBE CSFM# "320-1653:0201 SYSTEM SENSOR SCW - CEILING MOUNTED STROBES CSFM# 7125-1653:0186 DN-€0602:A1 FireWarden-1 00-2(E) Rev 3 Intelligent Addressable FACP The Notifier FireWarden-100-2 Rev 3 (NFW2-100) with Version 5.0 firmware is a combination FACP (Fire Alarm Control Panel) and DACT (Digital Alarm Communicator/Transmitter) all on one circuit board. This compact intelligent addressable control panel has an extensive list of powerful features. The SLC (Signaling Line Circuit) of the Fire Warden-100-2 Rev 3 operates using a Rapid Group Polling communication protocol technology that polls multiple devices simultaneously for a quicker device response time.This patented technology allows a fully-loaded panel with up to 198 devices to report an incident and activate the notification circuits in under 10 seconds. With this improved polling, devices can be wired on standard twisted, unshielded wire up to a distance of 10,000 feet. The 's quick-remove chassis protects the electronics during con- struction. The backbox can be installed allowing field wiring to be pulled. When construction is completed, the electronics can be quickly installed with just two bolts. New features for Rev 3 with Version 5.0 firmware include removable terminal blocks, improved transient protection, addi- tional secondary ANN-BUS, and increased power for the reset- table and remote sync outputs. Available accessories include ANN-BUS devices as well as ACS LED, graphic and LCD annunciators, and reverse polarity/city box transmitter. The integral DACT transmits system status (alarms, superviso- ries, troubles, AC loss, etc.) to a Central Station via the public switched telephone network. It also allows remote and local pro- gramming of the control panel using the PS-Tools Upload/Down- load utility. In addition, the control panel may be programmed or interrogated off-site via the public switched telephone network. Any personal computer with Windows® XP or greater, a com- patible modem, and PS-Tools—the Upload/Download software kit—may serve as a Service Terminal. This allows download of the entire program or upload of the entire program, history file, walktest data, current status and system voltages. The panel can also be programmed through the FACP's keypad or via a standard PS-2 computer keyboard, which can be plugged directly into the printed circuit board. This permits easy typing of address labels and other programming information. Version 5.0 firmware supports the following: Primary and Sec- ondary ANN-bus devices, NP-A100, USB port, NAC circuit diag- nostics, a new report has been added to the walk-test that lists untested devices, new device types added: audio telephone type code for NFV-25/50ZST, Photo Supervisory and auto-reset- table Drill (non-latching). The FireWatch Series internet monitoring modules IPDACT-2 and IPDACT-2UD permit monitoring of alarm signals over the Internet saving the monthly cost of two dedicated business tele- phone lines. Although not required, the secondary telephone line may be retained providing backup communication over the public switched telephone line. NOTE: Unless otherwise specified, the term "Fire Warden-100-2" is used in this document to refer to both the Fire Warden-100-2 and the Fire Warden-100-2E FACPs (Fire Alarm Control Panels). Like- wise, "NFW2-100" refers to NFW2-I00E as well. Features Listed to UL standard 864, 9th edition. On-board DACT. ovo NOTIFIER® 1,i [S1IIYATAYL1ll Remote site or local USB port upload/download, using PS- Tools. Four (4) Style Y (Class B) NAC circuits, whici can be con- verted to four (4) Style Z (Class A) circuits with optional ZNAC-92 converter module. (Up to 6.0 arrps total NAC power when using optional XRM-24B.) Selectable strobe synchronization for System Senso, Whee- lock, and Gentex devices. Remote Acknowledge, Silence, Reset and Drii via address- able monitor modules or FDU-80, N-ANN-80 or Legacy ACS Annunciators. ANN-BUS for connection to following optional modules (cannot be used if ACS annunciators are used): - N-ANN-80(-W) Remote LCD Annunciator - N-ANN-I/O LED Driver - N-ANN-S/PG Printer Module - N-ANN-RLY Relay Module - N-ANN-LED Annunciator Module - N-ANN-RLED Annunciator Module alarms oriy - ROME Relay Option Module Enclosure ACS & Terminal-mode Annunciators: - ACS Annunciators: Up to 32 Legacy ACM SeieE annuncia- tors (ACM-16AT or ACM-32 series). Cannot be used if ANN-BUS devices are used. - Terminal-mode Annunciators: Up to 32 Legacy FDU-80 annunciators. EIA-232 printer/PC interface (variable baud rate) on main cir- cuit board, for use with optional UL-listed printer P9N-6. Integral 80-character LCD display with backlighting. Real-time clock/calendar with automatic daylight savings control. Detector sensitivity test capability (NFPA 72 comp iart). DN-60602:A1 • 12/07/201 - PEge 1 of 6 History file with 1,000-event capacity. Maintenance alert warns when smoke detector dust accumu- lation is excessive. Automatic device type-code verification. One person audible or silent walk test with walk-test log and printout. Point trouble identification. Waterflow (nonsilenceable) selection per monitor point. System alarm verification selection per detector point. PAS (Positive Alarm Sequence) and presignal delay per point (NFPA 72 compliant). NOTE: Only detectors may participate in PAS. SLC LOOP: SLC can be configured for NFPA Style 4, 6, or 7 operation. SLC supports up to 198 addressable devices per loop (99 detectors and 99 monitor, control, or relay modules). SLC loop maximum length 10,000 ft. (3,000 m.). See installation manual for wire tables. NOTIFICATION APPLIANCE CIRCUITS (NA CS): Four onboard NACs with additional NAC capability using out- put control modules (NC-100). The four Class B NACs can be converted to four Class A NACs with optional ZNAC-92 converter module. Silence Inhibit and Auto Silence timer options. Continuous, March Time, Temporal or California code for main circuit board NACs with two-stage capability. Selectable strobe synchronization per NAC. 2.5 amps maximum per each NAC circuit. NOTE: Maximum 24VDC system power output is shared among all NAC circuits and 24VDC special-application auxiliary power outputs. Total available output is 3.0 amps. Using the optional XRM-24B transformer increases 24VDC output to 6.0 amps. PROGRAMMING AND SOFTWARE: Autoprogram (learn mode) reduces installation time. Custom English labels (per point) may be manually entered or selected from an internal library file. Three Form-C relay outputs (two programmable). 99 software zones. Continuous fire protection during online programming at the front panel. Program Check automatically catches common errors not linked to any zone or input point. OFFLINE PROGRAMMING: Create the entire program in your office using a Windows®-based software package (NFW2-100 requires PS-Tools Programming software, avail- able on www.magni-fire.com). Upload/download system pro- gramming locally to the NFW2-100 Rev 3 in less than one minute. USB upload/download programming with standard Male-A to Male-B cable. User Interface LED INDICATORS AC Power (green) Fire Alarm (red) Supervisory (yellow) Alarm Silenced (yellow) System Trouble (yellow) Maintenance/Presignal (yellow) Disabled (yellow) Battery Fault (yellow) Ground Fault (yellow) KEYPAD CONTROLS Acknowledge/Step Alarm Silence Drill System Reset (lamp test) 16-key alpha-numeric pad (similar to telephone keypad) 4 cursor keys Enter Product Line Information NFW2-100: FireWarden-100-2 Rev 3 198-point addressable Fire Alarm Control Panel, one SLC loop. Includes 80-character LCD display, single printed circuit board mounted on chassis, and cabinet. 120 VAC operation. NFW2-100R: Same as NFW2-100, except in a red backbox. NFW2-100E: Same as NFW2-100, except with 240 VAC opera- tion. 4XTM Reverse Polarity Transmitter Module: Provides super- vised output for local energy municipal box transmitter, alarm, and trouble. ZNAC-92: Optional converter module which converts four (4) Style V (Class B) NAC circuits to four (4) Style Z (Class A) cir- cuits. PS Tools: Programming software for Windows®-based PC computer (cable not included), available on www.firelite.com. DP-9692B: Optional dress panel for FireWarden-100-2 Rev 3. TR-CE-B: Optional trim Ring for semi-flush mounting. BB-26: Battery backbox, holds up to two 26 AH batteries and CHG-75. NFS-LBB: Battery box, houses two 55 AH batteries. CHG-75: Battery charger for lead-acid batteries with a rating of 25 to 75 AH. CHG-120: Remote battery charging system for lead-acid batter- ies with a rating of 55 to 120 AH. Requires additional NFS-LBB for mounting. NOTE: CHG-120 or CHG-75 required for batteries larger than I8AH. BAT Series: Batteries, see data sheet DN-6933. XRM-24B(E): Optional transformer, Increases system power output to 6.0 amps. Use XRM-24BE with FireWarden-100-2E Rev 3. PRTIPK-CABLE: Cable printer/personal computer interface cable; required for printer or for local upload/download program- ming and updating panel firmware. PRN-6: UL listed compatible event printer. Uses tractor-fed paper. IPDACT-2/2UD, IPDACT Internet Monitoring Module: Mounts in bottom of enclosure with optional mounting kit (PN IPBRKT). Connects to primary and secondary DACT telephone output ports for internet communications over customer provided ether- net internet connection. Requires compatible Teldat VisorALARM Central Station Receiver. Can use DHCP or static P. (See data sheet DN-60408 for more information.) IPBRKT: Mounting kit for IPDACT-2/2UD in common enclosure. IPSPLT: V-adaptor option allows connection of both panel dialer outputs to one IPDACT-2/2UD cable input. COMPATIBLE ANNUNCIATORS N-ANN-80(-W): LCD Annunciator is a remote LCD annunciator that mimics the information displayed on the FACP LCD display. Recommended wire type is un-shielded. (Basic model is black; order -W version for white; see DN-7114.) Page 2 of 6— DN-60602:A1 • 12/07/2010 N-ANN-LED: Annunciator Module provides three LEDs for each zone: Alarm, Trouble and Supervisory. Ships with red or black enclosure (see DN-60242). N-ANN-RLED: Provides alarm (red) indicators for up to 30 input zones or addressable points. (See DN-60242). N-ANN-RLY: Relay Module, which can be mounted inside the cabinet, provides 10 programmable Form-C relays. (See DN- 7107.) ROME-B: Relay Option Module Enclosure (order ROME-13 for black or ROME for red). Provides one N-ANN-RLY Relay Mod- ule already installed. The ROME Series provides mounting space for one additional Relay Module or one addressable Multi- module. (See Installation Sheet PN 53530.) N-ANN-S/PG: Serial/Parallel Printer Gateway module provides a connection for a serial or parallel printer. (See DN-7103.) N-ANN-I/O: LED Driver Module provides connections to a user supplied graphic annunciator. (See DN-7105.) ACM-8R: Relay module provides 8 Form-C 5.0 amp relays. ACM Annunciator Series: LED-type fire annunciators capable of providing up to 99 software zones of annunciation. Available in increments of 16 or 32 points to meet a variety of applications. LDM Graphic Series: Lamp Driver Module series for use with custom graphic annunciators. FDU-80 (Liquid Crystal Display) point annunciator: 80-char- acter, backlit LCD-type fire annunciators capable of displaying English-language text. NOTE: For more information on Compatible Annunciators for use with the Fire Warden-100-2 Rev 3, see the following data sheets (document numbers) ACM-8R (DN-3558), ACS/ACM Series (ON- 0524), LDM Series (DN-0551), FDU-80 (DN-6820). COMPATIBLE ADDRESSABLE DEVICES All feature a polling LED and rotary switches for addressing. NI-100: Addressable low-profile ionization smoke detector. NP-100: Addressable low-profile photoelectric smoke detector. NP-lOOT: Addressable low-profile photoelectric smoke detector with thermal sensor. NP-100R: Addressable remote test capable detector for use with DNR(W) duct smoke detector housings. NH-100: Fast-response, low-profile heat detector. NH-100R: Fast-response, low-profile heat detector with rate-of- rise option. NH-100H: Fixed high-temperature detector that activates at 1 90F/88C. NP-Al 00: Addressable low-profile multi-sensor detector. DNR: Innovair Flex low-flow non-relay duct-detector housing. Order NP-100R separately. DNRW: Innovair Flex low-flow non-relay duct-detector housing, with NEMA-4 rating. Watertight. (Order NP-100R separately.) NMM-100: Addressable Monitor Module for one zone of nor- mally-open dry-contact initiating devices. Mounts in standard 4.0' (10.16 cm.) box. Includes plastic cover plate and end-of-line resistor. Module may be configured for either a Style B (Class B) or Style D (Class A) IDC. NDM-100: Dual Monitor Module. Same as NMM-100 except it provides two Style B (Class B) only lDCs. NMM-100P: Miniature version of NMM-100. Excludes LED and Style D option. Connects with wire pigtails. May mount in device backbox. NZM-100: Similar to NMM-100, but may monitor up to 20 con- ventional two-wire detectors. Requires resettable 24 VDC power. Consult factory for compatible smoke detectors. NC-100: Addressable Control Module for one Style Y/Z (Class B/A) zone of supervised polarized Notification Appliances. Mounts directly to a 4.0" (10.16 cm.) electrical box. Notification Appliance Circuit option requires external 24 VDC to power noti- fication appliances. NC-100R: Addressable relay module containing two isolated sets of Form-C contacts, which operate as a DPDT switch. Mounts directly to a 4.0" (10.16 cm.) box, surface mount using the SM13500. NOT-BG12LX: Addressable manual pull station with interface module mounted inside. N100-ISO: Fault Isolator Module. This module isolates the SLC loop from short circuit conditions (required for Style 6 or 7 oper- ation). SMB500: Used to mount all modules except the NMM-100P. NMM-100-10: Ten-input monitor module. Mount one or two modules in a BB-XP cabinet (optional). Mount up to six modules on a CHS-6 chassis in a 1313-25. NZM-100-6: Six-zone interface module for compatible conven- tional two-wire detectors. Mount one or two modules in a BB-XP cabinet (optional). Mount up to six modules on a CI-lS-6 chassis in a 1313-25. NOTE: For more information on Compatible Addressable Devices for use with the Fire Warden-100-2 Rev 3, see the following data sheets (document numbers): N100-ISO (DN-6994), NP-100 series (DN-6995), NI-100 (DN-6996), NH-100 series (DN-6997), ND-100 series (DN-7006), NP-A100 (DN-6998), NMM- 100/NMM- loop, NDM-100/NZM-100 (DN-6999), NC- 100/NC-IOOR (DN-7000), NOT-BGI2LX (DN-7001), NMM-100-10 (DN-6990), and NZM- 100-6 (DN-60 150). Wiring Requirements While shielded wire is not required, it is recommended that all SLC wiring be twisted-pair to minimize the effects of electrical interference. Wire size should be no smaller than 18 AWG (0.78 mm2) and no larger than 12 AWG (3.1 mm2). The wire size depends on the length of the SLC circuit. Refer to the panel manual for wiring details. DN-60602:A1 • 12/07/2010 - Page 3 of 6 FireWarden-100-2 Rev 3 Fire Alarm Control/ Communicator EIA-485 INTERFACE (four wires) L0 ANN-BUS DEVICES N-ANN-80, N-ANN-LED, N-ANN-S/PG, N-ANN-I/O NOTE: System can use either ANN-BUS devices OR ACS-mode annunciators. They cannot be used simultaneously. Optional REVERSE POLARITY! CITY BOX OUTPUT 44 (4XTM) 8 FORM-C, 5-AMP RELAYS (optional, order ACM-BR) NACs (Notification Appliance Circuits) BELLS, SIGNALS, STROBES EIA-232 INTERFACE (PIM-24) built into the motherboard NOTE: System can use either the printer OR the FDU-80. They cannot be used simultaneously. 24 VDC - - FDU-80 Up to 6,000 ft. (1825.8 m) between each FDU-80 in the EIA-485 loop, and between each FDU-80 and the FACP. —0 SMOKE DETECTORS NP-100, NP-lOOT, NI-100, NP-A100 —* I HEAT DETECTORS NH-100, NH-100R, NH-100H DUCT DETECTORS ND-100, ND-100R, DNR —+ I. MONITOR/CONTROL NMM-100, NZM-100, NDM-100, N100-ISO, NC-100, NC-100R 0 I I I I I ADDAS76ABLE MULTI-MODULE NZM-100-6, NMM-100-10 MINI-MONITOR N MM-lOOP PULL STATION NOT-BG1 2LX ANN-BUS or EIA-485 in ACS mode (two wires) Page 4 of 6— DN-60602:A1 • 12/07/2010 DN-60602:A1 • 12/07/2010- Page 5 of 6 SYSTEM SPECIFICATIONS System Capacity Intelligent Signalling Line Circuits ......................................... 1 Addressable device capacity............................................198 Programmable software zones...........................................99 ACS Annunciators ..............................................................32 ANN-bus devices................................................................16 Electrical Specifications AC Power: FireWarden-100-2 Rev 3: 120 VAC, 60 Hz, 3.0 amps. FireWarden-100-2 Rev 3(E): 240 VAC, 5 0 Hz, 1.5 amps. Wire size: minimum 14 AWG (2.00 mm2) with 600 V insulation. Battery charger capacity: 7 AH - 18 AH batteries. Up to two 18 Ah batteries can be housed in the FACP cabinet. Larger batter- ies require an external battery charger such as the CHG-75 or CHG-120, and a separate battery cabinet such as the BB-26 or NFS-LBB. Communication Loop: Supervised and power-limited. Notification Appliance Circuits: Each terminal block provides connections for two Style Y (Class B) for a total of four Style Y (Class B) or with an optional ZNAC-92 module converts to four Style Z (Class A) NACs. Maximum signaling current per circuit: 2.5 amps. End-of-Line Resistor: 4.7K ohm, 1/2 watt (P/N 71252 UL listed) for Style Y (Class B) NAC. Refer to panel documenta- tion and Notifier Device Compatibility Document for listed com- patible devices. Two Programmable Relays and One Fixed Trouble Relay: Contact rating: 2.0 amps @ 30 VDC (resistive), 0.5 amps @ 30 VAC (resistive). Form-C relays. Special Application Non-resettable Power (24 VDC Nomi- nal): Jumper selectable (JP4) for conversion to resettable power output. Up to 1.0 amp total DC current available from each out- put. Power-limited. Special Application Resettable Power (24 VDC nominal): Jumper selectable (JP6) for conversion to non-resettable power. Up to 1.0 amp total DC current available. Refer to the Notifier Device Compatibility Document for listed compatible devices. Remote Sync Output: Remote power supply synchronization output. Nominal special application power: 24 VDC. Maximum current: 300 mA. End-of-Line Resistor: 4.7K ohm. Output linked to NAC 1 control. Supervised and power-limited. Telephone Interface: Unless used with Teldat VISORALARM, requires dedicated business telephone number with a minimum of 5 volts DC (off-hook voltage). Obtain dedicated phone line directly from your local phone company. Do not use shared phone lines or PBX (digital) type phone line extensions. Cabinet Specifications Door: 19.26' (48.92 cm.) high x 16.82' (42.73 cm.) wide x 0.12' (.30 cm.) deep. Backbox: 19.00° (48.26 cm.) high x 16.65 (42.29 cm.) wide x 5.20 (13.34 cm.) deep. Trim Ring (TR-CE- B): 22.00 (55.88 cm.) high x 19.65 (49.91 cm.) wide. Shipping Specifications Weight: 26.9 lbs. (12.20 kg.) Dimensions: 20.00" (50.80 cm.) high x 22.5" (57.15 cm.) wide x 8.5" (21.59 cm.) deep. Temperature and Humidity Ranges This system meets NFPA requirements for operation at 0 - 49°C/32 - 120°F and at a relative humidity 93% ± 2% RH (non- condensing) at 32°C ± 2°C (90°F ± 3°F). However, the useful life of the system's standby batteries and the electronic compo- nents may be adversely affected by extreme temperature ranges and humidity. Therefore, it is recommended that this system and its peripherals be installed in an environment with a normal room temperature of 15 - 27°C/60 - 80°F. NFPA Standards The FireWarden-100-2 Rev 3 complies with the following NFPA 72 Fire Alarm Systems requirements: - LOCAL (Automatic, Manual, Waterflow and Sprinkler Supervisory). - AUXILIARY (Automatic, Manual and Waterflow) (requires 4XTM). - REMOTE STATION (Automatic, Manual, Waterflow and Sprinkler Supervisory) (Where a DACT is not accepted, the alarm, trouble and supervisory relays may be connected to UL 864 listed transmitters. For reverse polarity signaling of alarm and trouble, 4XTM is required.) - PROPRIETARY (Automatic, Manual, Waterflow and Sprin- kler Supervisory). - CENTRAL STATION (Automatic, Manual, Waterflow and Sprinkler Supervisory). - 01, PSDN (Other Technologies, Packet-switched Data Net- work) Agency Listings and Approvals The listings and approvals below apply to the basic FireWarden- 100-2 Rev 3 control panel. In some cases, certain modules may not be listed by certain approval agencies, or listing may be in process. Consult factory for latest listing status. UL Listed: S635 FM approved CSFM: 7165-0028:0235 MEA: 120-06-E, Volume 2 For ULC-listed version, see DN-60600. NOTIFIER® is a registered trademark of Honeywell International Inc. Wheelock® is a registered trademark of and ExcederT is a trademark of Cooper Notification. 02010 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited. This document is not intended to be used for installation purposes. I So ooi We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. GINEERING 9 MANUFACTURING All specifications are subject to change without notice. QUALITY SYSTEMS Made in the U.S. A. For more information, contact Notifier. Phone: (203)484-7161, FAX: (203)484-7118. www.notifier.com Page 6 of 6- DN-60602:A1 • 12/07/2010 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM k 11W LISTING SERVICE LISTING No. 7165-0028-.0235 Page 1 of I CATEGORY: 7165 -- FIRE ALARM CONTROL UNIT (COMMERCIAL) LISTEE: NotifierOne Fire-Lite Place, Northford, CT 06472-1653 Contact: Vladimir Kireyev (203) 484-6277 Fax (203) 484-7309 Email: vladimir.kireyev@honeywell.com DESIGN: Models Fire Warden 100 and Fire Warden 100-2 addressable control units. Local, auxiliary, remote station, central station and proprietary (protected premise). This panel also can be used with NFV-25/50ZST (Fire Voice-25/-50ZST) Zoned System Voice with Telephone for Emergency Voice evacuation Applications. Refer to listee's data sheet for detailed product description, operational considerations and required/optional accessories. When required, accessories shall be CSFM listed. RATING: 120 VAC, 60 Hz, 2.06 A Primary, 24 VDC Secondary INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating, and UL label. APPROVAL: Listed as an addressable fire alarm control panel for use with separately listed compatible initiating and indicating devices. Refer to listee's Installation Instruction Manual for details. This control unit can generate a distinctive three-pulse Temporal Pattern Fire Alarm Evacuation Signal (for total evacuation) in accordance with NFPA 72, 2002 Edition. *Fire Warden 100-2 panel also suitable for high-rise application for use with Model NFC-50/100 emergency voice evacuation panel (CSFM # 6911-0028:0265). This control unit meets the requirements of UL Standard 864, 9th Edition. NOTE: For Fire Alarm Verification Feature (delay of fire alarm signal), the maximum Retard/Reset/Restart period shall not exceed 30 seconds. XLF: 7165-0075:0208 *Rev. 11-15-13GT This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2015 Listing Expires June 30, 2016 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division DN-60772:A1 .First Command I I [.I.J 0 by Honeywell Notifiers First Command NFC-50/100 and NFC-50/100E are multipurpose emergency voice evacuation panels for fire appli- cations, mass notification applications, or both. The First Com- mand delivers 50 or 100 watts of audio power for distribution to up to eight speaker circuits (i.e. zones). The NFC-50/100(E) comes standard with a single speaker circuit and a built-in 50 watt, 25V amplifier. A secondary 50 watt amplifier (NFC-BDA- 25/70V) can be added for single speaker circuit backup or to increase system capacity to two speaker circuits and an addi- tional 50 watts of audio power. An optional NFC-CE6 module added to the NFC-50/1 00(E) will upgrade the system to a max- imum of eight speaker circuit outputs. All speaker output cir- cuits can be wired in either Style Y (Class B) or Style Z (Class A) configuration. The NFC-50/100(E) has fourteen field pro- grammable messages (up to 60 seconds each), built-in field configurable pre- and post-announce tone generators and a fully supervised Notification Appliance Circuit (NAC) with 2.0 amps of synchronized NAC power. The NFC-50/100(E) includes three built-in Form-C relay contacts, (AC power, trou- ble and MNS active) a NAC follower and 500mA special appli- cation power. A built-in power supply delivers operational power and on board battery charger supports charging up to 26AH batteries (NFC cabinet holds up to 18AH batteries). For fire protection applications, the NFC-50/100(E) is an adjunct (slave) to most UL listed FACP5 or as a stand-alone unit for non-fire applications. For seamless integration between fire and mass notification, the NFC-50/100(E) can be activated by the NFW2-100(Rev 3) and NFW-50 when con- nected to the ACS/ANN serial communication bus. Activation of the NFC-50/100(E) via other FACPs uses the eight on board Command Input Circuits (CMDs). Two of the eight CMD circuits (CMD 1 & CMD 2) can be individually field pro- grammed for activation by an FACP Notification Appliance Cir- cuit reverse polarity and all eight can be activated by a contact closure. In addition, the NFC-50/100(E) can be activated from a building's Private Branch Exchange (PBX) with the integral night ring feature. All NFC-50/100(E) programming is done by using a simple, built-in programming utility accessed from any laptop. For added flexibility, the NFC-50/100(E) supports both 25V and 70V speaker output operation. By adding a 70V transformer conversion module (NFC-XRM-70V) or an additional 70 volt secondary amplifier (NFC-BDA-25/70V) the system supports 70 volt speaker devices. The NFC-50/100(E) can expand in order to accommodate larger or more complex installations. To add more control and increase system capacity, any combination of up to eight exter- nal remote consoles (including the NFC-LOC, NFC-RPU, and NFC-RM) and up to eight distributed audio amplifiers (includ- ing the NFC-50DA(E) and NFC-125-DA(E) can be connected on the external data bus and audio riser data bus to create a fully integrated command center. A fully loaded system sup- ports up to 1100 watts of total audio power and up to 24 speaker circuit outputs. TYPICAL APPLICATIONS Schools • Nursing Homes • Factories Theaters • Military facilities • Restaurants Auditoriums • Places of Worship • Office Buildings Features UL Listed to UL 2572 Communication (Control Units Mass Notification Systems) and UL 864 (emergency voice evacu- ation for fire). Modular design for system flexibility and easy expansion. Removable terminal blocks. 50 watts of 25V audio power (expandable to 100 watts) RMS. 2 amp Notification Appliance Circuit (NAC) output, sync gene ator, or follower for System Sensor, Wheelock or Gen- tex protocols. Optional 70V transformer available for the primary amplifier. (Note that speaker wiring continues to be supervised in stancby, alarm and when background music is playing with this cptional transformer installed). Eight Command Input Circuits to activate messages 1 to 8: - CrVD1 and CMD2 are field selectable to be activated from 12 or 24 VDC Notification Appliance Circuits (reverse polarity) or contact closures. - CMD3-CMD8 are activated by contact closures. Speaker Circuits. - Sirgle Style Y (Class B) or Style Z (Class A) speaker Cir- cuit. DN-60772:A1 • 7/15/13 - Page 1 of 8 - Two Style V (Class B) or Style Z (Class A) speaker cir- cuits (with optional NFC-BDA-25/70V Audio Amplifier installed). - Eight Style V (Class B) or Style Z (Class A) speaker cir- cuits (with optional NFC-BDA-25170V and NFC-CE6 installed). NFC-50/100(E) can be controlled by an FACP via the ANN/ ACS (EIA-485) link of the NFW2-100 (Rev 3). Integral supervised microphone. Microphone time-out feature which reverts back to pre- recorded message if emergency page exceeds the pro- grammed time. 14 recorded messages. Field-selectable message and custom message recording capability using the local microphone, a USB port, or an external audio input. External Audio Input can be used for background music. Up to 60 second message duration for all messages. Integral tone generators field selectable for multiple tone types. Powered by integral AC power supply or batteries during AC fail. Programmable delay of immediate, 2 hours or 6 hours reporting of AC Loss. Piezo sounder for local trouble. 100 event history log. Three Form-C relays: - AC Power Loss Relay - T131. - System Trouble Relay - T132. - MNS Active - TB3. 500mA (0.5A) Special Application (auxiliary power) output for addressable modules when interfaced with compatible addressable FACPs and End-of-Line power supervision relays. System Status LEDs (refer to "Controls and Indicators" on product manual LS10001-000NF-E). Integral Dress Panel. Optional TR-CE-B semi-flush trim ring. Any combination of up to eight (8) external remote con- soles: - Optional NFC-RM Remote Microphone (includes cabi- net). See DN-60778. - Optional NFC-RPU Remote Page Unit (includes cabinet). See DN-60775. - Optional NFC-LOC Local operator console (includes cab- inet). See DN-60777. Any combination of up to eight (8) distributed audio amplifi- e rs: - Optional NFC-50DA(E) distributed amplifier, 50 watts. See DN-60776. -Optional NFC-125DA(E) distributed amplifier, 125 watts. See DN-60776. Optional Internal Expansion Modules NFC-CE6: Circuit Expander Module provides connections for up to six Style Z (Class A) or Style V (Class B) speaker cir- cuits. Circuits are configured through the web-based program- ming utility. NFC-BDA-25V: 25V, 50 watt audio amplifier module. Adding a second speaker circuit increases the total NFC-50/100 power output to 100 watts or can also be used as a backup amplifier. NFC-BDA-70V: 70V, 50 watt audio amplifier module. Adding a second speaker circuit increases the total NFC-50/100 power output to 100 watts or can also be used as a backup amplifier. NFC-XRM-70V: 70V Transformer Conversion Module. Con- verts the NFC-50/100(E) primary amplifier to a 70V output. This transformer mounts directly to the NFC-50/100(E) main control board by two metal brackets. Page 2 of 8— DN-60772:A1 • 7/15/13 NFC-RM remote microphone CHG-120 charger NFC-50/1 00(E) FirstCommand (Possible Configurations) I-n OLE Erobes *C-BDA-2 _ ions NF 5170V optional amplifier NFC-CE6 circuit expander TB19 TB2O&TB21 C Circuit Speaker. Circuits ml lJI NFC-FFT firefighter telephone II remote NFC-LOC NFC-RPU consoles local operator console remote paging unit flU1 H ri - TB12 rrn TB22 ___________ charger - J7 UIOLI 3 F-I F-I 14 > NFC-50D — _ A 50W NFC-125DA 125W remote amplifier remote amplifier DN-60772:A1 • 7/15/13 - Page 3 of 8 SYSTEM OVERRIDE SPEAKER 4111117110111 EI1 ZONE ii ME SPEAKER SPEAKER ZONE 14 ZONE 2 SPSN0ER 3 ZONE 15 ZONE SPEAKER m aa TO PAGE O3SPEAKER ZONE 4 SPEAKER ZONE To MOPI4KSIE TROUBLE 33 SgAXER ZONE S SPEAK ZONE 17 MESSAGEI SPE AKER SPEAKER ZONE18 c MESSAGE 2 D MESSAGES ZOAK8 NE SPEAKER ZONE 20 MESSAGE 4 90 SPEAKER ZONES 210 SPEAKER ZONE 21 o ,MESSAGE 10 ZONE 22 MESSAGE M SP EAKER ZONE I I SPEAKER ZONE23 CB~ MSUAGE1 SPEAKOR ZONE OT,!K MESSAGES 09We 0 AMPS AC POWR 0 110 MAI" cosois GIST PI,lF' I GROIAE EMULT D p. LOCI > SlAT, AMP 2 CEIEIRPAIJLT 0 LOC A oisi AMP s I DASTERYFAULT D' RPU1 > SlAt AMP SA* SASS GUSF*ULF > RPUA AT ., .AMP > MACPASILT o RPUA SlAT AMPS MAC SCORE > PM 1 f> GIST. AMP 7 )> SYSTEM TIRtE RN 2 1S GIST AMP S > AlJrno ASIA FAULT ' 0 > P1.12 Control and Indicators PUSH BUTTON CONTROLS All Call • Message Select 1-14 MNS Control • Diagnostic Select System Control • Trouble Silence Speaker Select 1-24 • Console Lamp Test Page 4 of 8— DN-60772:A1 • 7/15/13 LED Status Indicators (visible with door closed) Fire System Active (green) LOC/RPUIRM 1-8 Active (green) MNS Control (green) Main Console Fault (yellow) System Control (green) AC Power (green) System in Use (green) Ground Fault (yellow) Speaker Zone 1-24 Active Charger Fault (yellow) (green) Speaker Zone 1-24 Fault Battery Fault (yellow) (yellow) OK to Page (green) Data Bus Fault (yellow) Microphone Trouble (yellow) NAC Fault (yellow) Message 1-8 Active (red) NAC Active (green) Message 1-8 Fault (yellow) System Trouble (yellow) Remote Amplifier 1-8 Fault Audio Riser Fault (yellow) (yellow) LOCIRPU/RM 1-8 Fault (yellow) LED Indicators (visible with door and dress panel open) Speaker Volume Control Fault (yellow). Option Card Fault (yellow). IF Amplifier Over Current Fault (yellow). Product Line Information NFC-50/100: (Primary Operating Console) 50 Watt, 25V single speaker zone emergency voice evacuation system, integral microphone, built in tone generator and 14 recordable mes- sages. NFC-50/100E: Export version (Primary Operating Console) 50 Watt, 25V single speaker zone emergency voice evacuation system, integral microphone, built in tone generator and 14 recordable messages. (240 VAC, 50Hz). NFC-CE6: Speaker Circuit/Zone Expander Module. NFC-BDA-25V: 25V, 50 watt audio amplifier module. Adding a second speaker circuit increases the total NFC-50/100 power output to 100 watts or can also be used as a backup amplifier. NFC-BDA-70V: 70V, 50 watt audio amplifier module. Adding a second speaker circuit increases the total NFC-50/100 power output to 100 watts or can also be used as a backup amplifier. NFC-XRM-70V: 70V Transformer Conversion Module. Con- verts the NFC-50/100(E) primary amplifier to a 70V output. This transformer mounts directly to the NFC-50/100(E) main control board by two metal brackets. NFC-LOC: Local Operator Console (Complete user interface), Please refer to the data sheet DN-60777 for more information. NFC-RPU: Remote Page Unit Hand held microphone, 14 mes- sage buttons. Please refer to the data sheet DN-60775 for more information. NFC-RIM: Remote Microphone only. Please refer to the data sheet DN-60778 for more information. NFC-50DA: Distributed (Remote) Audio Amplifier, 50 watts. Please refer to the data sheet DN-60776 for more information. NFC-50DAE: Export version. Distributed (Remote) Audio Amplifier, 50 watts. (240 VAC, 50Hz). Please refer to the data sheet DN-60776 for more information. NFC-125DA: Distributed (Remote) Audio Amplifier, 125 watts. Please refer to the data sheet DN-60776 for more information. NFC-125DAE: Export version. Distributed (Remote) Audio Amplifier, 125 watts. (240 VAC, 50Hz). Please refer to the data sheet DN-60776 for more information. NFC-CE4: Distributed Audio Speaker Circuit/Zone expander module. NFC-FFT: Fire Fighter Telephone System. Please refer to the data sheet DN-60779 for more information. N-FPJ: Remote Phone Jack. FHS-F: Fire Fighters Remote Handset. FHSC-R: Fire Fighters Handset Cabinet Recessed. FHSC-S: Fire Fighters Handset Cabinet Surface Mount TR-CE-B: Optional Trim Ring. THUMBLTCH: Optional Thumb Latch. (Non UL-Listed). CHG-75: 25 to 75 ampere-hours (AH) External Battery Charger. CHG-120: 25-120 ampere-hours (AH) External Battery Charger. ECC-MICROPHONE: Replacement Microphone only. BAT-1270: Battery,12 volt,7.0 AH (Two required). BAT-12120: Battery, 12 volt, 12.0 AH (Two required). BAT-12180: Battery,12 volt, 18.0 AH (Two required). BAT-12260: Battery, 12 volt, 26.0 AH (Two required). BB-26: Battery cabinet mounts up to two 26 AH batteries. Wiring Requirements See product manual, part number LS10001-001NF-E for detailed wiring requirements. Total System Capacity: (NFC-50/1 00(E) only) Total Built-in Audio Power: 50 Watts. Total Expandable Audio Power: 100 Watts. Total Built-in Speaker Circuits: 2. Total Expandable Speaker Circuits: 8. Audio Message Max Time Duration: 60 seconds. External Audio Input: 1. Total System Capacity: (Fully Loaded System) Total Distributed Audio Power: 1100 Watts. Total Speaker Circuits Per System: 24. Total Remote Consoles Supported: 8. Total Distributed Audio Amplifiers Supported: 8. Electrical Specifications PRIMARY (AC) POWER (TB 15) NFC-50/100: 120 VAC, 60 Hz, 3.5 amps. NFC-50/100E: 240 VAC, 50 Hz, 2.0 amps. Wire size: minimum #14 AWG (2.00mm2) with 600 V insulation. SECONDARY POWER (BATTERY) CHARGING CIRCUIT (J7) Supports lead-acid batteries only. Float charge voltage at 27.3V Maximum charge current: 1.0 Amp Maximum battery charge capability: 2.8 Amps, 26AH (NFC cabinet holds max. 18AH battery). Minimum Battery size: 12 Amp Hour. AC Loss RELAY CONTACT RATING (TB3) 2.0 amps @ 30 VDC (resistive), 0.5 amps @ 30 VAC (resistive). FORM C - TROUBLE RELAY CONTACT RATING (TB2) 2.0 amps @ 30 VDC (resistive), 0.5 amp @ 30 VAC (resistive). MNS ACTIVE RELAY CONTACT RATING (TBI) 2.0 amps @ 30 VDC (resistive), 0.5 amps @ 30 VAC (resistive). NOTIFICATION APPLIANCE CIRCUIT (NAC) OUTPUT RATING (TB 19) One (1) Style Y (Class B) or Style Z (Class A) circuit. Power-limited circuitry, (Class 2) supervised. Nominal operating voltage: 24 VDC. Maximum signaling current for special application power: 2.OA. Maximum signaling current for regulated power: 200mA. Maximum wiring impedance: 1ft Current limit: fuse-less, electronic, power-limited. End-Of-Line Resistor: 4.7 K, ½ watt, (P/N 71252) required for Style V (Class B) operation. Refer to the Device Compatibility Document 15378 for listed compatible devices. NAC FOLLOWER OUTPUT REMOTE SYNC (TB 18) Connections for FACP NAC synchronization trigger signal. Output terminals: pass-through to other system compo- nents. Trigger input voltage: 9 to 32 VDC, 24 VDC rated. Input current draw in Alarm condition: 10 mA at rated volt- age. SPECIAL APPLICATION POWER (AUX. POWER) (TB17) 500 mA @ 24 VDC. Used for powering addressable modules and associated End-of-Line power supervision relays. Power-limited circuitry. Refer to the Device Compatibility Docu- ment 15378 for a list of compatible devices. SPEAKER VOLUME CONTROL OVERRIDE (TB23) Style V (Class B) or Style Z (Class A) circuit. Special application power. Power-limited circuitry, supervised. Nominal operating voltage: 24 VDC. Maximum signaling current: 0.25 amps. Current limit: fuse-less, electronic, power-limited. End-Of-Line Resistor: 4.7 K, ½ watt, (P/N 71252) required for Style V (Class B) operation. Speaker Circuits Primary Speaker Circuit (T820) Secondary Speaker Circuit (TB21) (with optional amplifier only). - Circuit can be wired Style V (Class B) or Style Z (Class A). - Power-limited circuitry. - Normal Operating Voltage: 25 VRMS @ 2 amps max and maximum Load Impedance of 12.52 (70V @ 700 mA max. with maximum load Impedance of 100) operation possible by plugging optional NFC-XRM-70V conversion transformer into J12 of the main control board). DN-60772:A1 • 7/15/13 - Page 5 of 8 -Output Power: 50 watts (10 watts when background music is employed). - Frequency Range: 400Hz - 4,0001-1z. - Maximum total capacitance for each speaker circuit: 250 uF - End-of-Line Resistor required for Style Y circuit: 15 K2, 1 wall (PIN: ELR-15K). Command Input Circuits (alarm polari- ties shown) CMD1 - TB4 Terminals 3(+) & 4(-) are input terminals and Ter- minals 1(-) and 2(+) are output terminals which provide feed through of the NAC circuits to NAC devices down stream. CMD2 - TB5 Terminals 3(+) & 4(-) are input terminals and Ter- minals 1(-) and 2(+) are output terminals which provide feed through of the NAG circuits to NAG devices downstream. GMD3 - TB6 Terminals 1(+) & 2(-) are input terminals for con- tact closure only. GMD4 - TB6 Terminals 3(+) & 4(-) are input terminals for con- tact closure only. GMD5 - TB7 Terminals 1(+) & 2(-) are input terminals for con- tact closure only. CMD6 - TB7 Terminals 3(+) & 4(-) are input terminals for con- tact closure only. GMD7 - TB8 Terminals 1(+) & 2(-) are input terminals for con- tact closure only. GMD8 - TB8 Terminals 3(+) & 4(-) are input terminals for con- tact closure only. Power-limited and supervised circuitry. Normal Operating Voltage Range: 10.5 VDG - 29 VDC; (Maximum Voltage: 29 VDG). NAG Reverse Polarity Current (requires End-of-Line Resis- tor from NAG): 1.6 mA maximum. Contact Closure Operation Current (requires 4.7KQ, ½ wall End-of-Line Resistor P/N 27072): 6.6 mA maximum. Maximum Wiring Impedance CMD1 - GMD8 (Contact Clo- sure Operation): 2000. NOTE: When the system is programmed for Mass Notification, CMD land CMD2 will be programmed for Reverse Polarity only. See manual P/N LS10001-001NF-E for more details. MAXIMUM INPUT IMPEDANCE: CMD1 & CMD2 (Reverse Polarity Operation): 20K. CMD1 - CMDB (Contact Closure Operation): 4.75KQ. NIGHT RING INPUT - TB 16, TERMINALS 1 (+) & 2 (-) Contact closure input. Isolated, non-supervised. Operation current: 3.8 mA, maximum. Maximum wiring impedance: 30K. Minimum isolation withstand voltage: 1500 VRMS. EXTERNAL OPERATOR INTERFACE POWER OUTPUT (TB24) Non-resettable power for external operator interface com- ponents. Power-limited circuitry, non-supervised. Nominal operating voltage: 24 VDG. Maximum output current: 0.80 amps. Current limit: fuse-less, electronic, power-limited circuit. EXTERNAL DATA BUS (EIA-485) (TBI2) Data connections for external operator interface components. Redundant transceiver circuitry for Glass A operability. Power-limited circuitry, supervised. Maximum wiring impedance: 13.292. FACP DATA BUS (EIA -485) (TB 13) Dedicated connection to FAGP serial bus. Output terminals: pass-through to other system components. Isolated, supervised. Minimum isolation withstand voltage: 1500 VRMS. Maximum wiring impedance: 40Q (ANN-BUS), 26Q (ACS-BUS). External Audio Riser (TB22). Style Y (Glass B) or Style Z (Glass A) audio connections to external operator interface components. Power-limited circuitry, supervised. Audio signal level: 3.85 V, maximum. Frequency range: 400 Hz - 4 KHz RMS. Frequency range (NFC-50/1 25DA): 800Hz - 2KHz RMS. EXTERNAL AUDIO INPUT (TB5) Input Impedance: 8.5Kg nominal @1KHz. Input Voltage: 700 mV rms maximum. Input Current: 0.1 mA maximum @ 700 mV. NOTE: Some laptops/personal computers only provide an audio output for headphones. It may be necessary to adjust the head- phone output level for proper recording of voice messages. NFC-CE6 Circuit Expander Module Specifications Power-limited circuitry. Up to six (6) circuits on the NFC-GE6 can be wired as Style V (Glass B) or Style Z (Glass A). Normal Operating Voltage for Speaker Circuits: 25 V@ 2.0 amps max. (Maximum Load Impedance of 12.50). 70.0 V © 700 mA max. with maximum Load Impedance of 1000 operation possible for the primary circuit by plugging in an optional NFG-XRM-70V conversion transformer into J12 of the main control board. The same operation is possi- ble for the optional 50W amplifier by selecting the NFC- BDA-70V model. Speaker circuit wiring is supervised during standby, back- ground music, and alarm. Output Power: 50 watts total; Frequency Range: 4001-1z - 4,000Hz. Maximum total capacitance: 250 pF. (Note that the total capacitance for the speaker outputs must not exceed the maximum of 250 iJF). End-of-Line Resistor required for Style V (Class B) speaker circuit: 15 KQ, 1 watt (P/N: ELR-15K)TB13 on the main control board: ACS/ANN (ElA-485) electrically isolated link to FAGP provides programmed speaker control. Cabinet Specifications Backbox: 19.0(48.26 cm) high x 16.65(42.29 cm) wide x 5.20(13.23 cm) deep. Door: 19.26" (48.92 cm) high x 16.82(42.73 cm) wide x 0. 12"(0.30 cm) deep. Trim Ring (TR-GE-B): 22.00" (55.88 cm) high x 19.65" (49.91 cm) wide. Shipping Specifications Base Unit Weight: 27.85 lbs (12.63 kg). Page 6 of 8— DN-60772:A1 • 7/15/13 Temperature and Humidity ranges This system meets NFPA requirements for operation at 0-49 C/32-1202 F and at a relative humidity 93% ± 2% RH (non- condensing) at 32°C ± 2°C (90°F ± 3°F). However, the useful life of the systems standby batteries and the electronic com- ponents may be adversely affected by extreme temperature ranges and humidity. Therefore, it is recommended that this system and its peripherals be installed in an environment with a normal room temperature of 15-27 C/60-809 F Agency Listings and Approvals The listings and approvals below apply to the basic NFC-50/ 100(E) control panel. In some cases, certain modules may not be listed by certain approval agencies or listing may be in pro- cess. Consult factory for latest listing status. UL Listed S635. Compliant with UFC4-021-01. Standards and Codes The NFC-50/100(E) complies with the following UL Standards and with NFPA 72 Fire Alarm system requirements. UL 864. UL 2572. DN-60772:A1 • 7/15/13 - Page 7 of 8 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 6911-0028:0265 Page 1 of 1 CATEGORY: 6911 --VOICE COMMUNICATION SYSTEMS CONTROL UNITS LISTEE: NotifierOne Fire-Lite Place, Northford, CT 06472-1653 Contact: Vladimir Kireyev (203) 484-6277 Fax (203) 484-7309 Email: vladimir.kireyev©honeywell.com DESIGN: Models NFC-50/100 and NFC-50/100E. These are 50-watt audio emergency voice evacuation panels expandable to 100-watt for fire applications, mass notification applications, or both. Refer to listee's data sheet for additional detailed product description and operational considerations. System components: ECC-MCB; Main Control Board ECC-DKVCM; Display Board NFC-BDA-25V; Amplifier Module 25 VRMS NFC-BDA-70V; Amplifier Module 70 VRMS NFC-CE6; Speaker Circuit Expander Module NFC-XRM-70V; Transformer Module 70.7 VRMS RATING: Primary Operating: 120 V, 60 Hz, 3.5 A or 240 V, 50 Hz, 2 A INSTALLATION: In accordance with listee's printed installation instructions, applicable codes & ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating, and UL label. APPROVAL: Listed as voice communication systems for use with separately listed compatible fire alarm control units to provide emergency voice evacuation signals. Refer to listee's Installation Instruction Manual for details. XLF: 6911-0075:0226 08-06-13 gt This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2015 Listing Expires June 30, 2016 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division dn-71 14:c • Al -65 (a NOTIFIER® Serial Annunciator by Honeywell General N-ANN-80 80-Character LCD The N-ANN-80 annunciator is a compact, backlit, 80-character LCD fire annunciator that mimics the Fire Alarm Control Panel (FACP) display. It provides system status indicators for AC Power, Alarm, Trouble, Supervisory, and Alarm Silenced condi- tions. The N-ANN-80 and the FACP communicate over a two- wire serial interface employing the ANN-BUS communication format. Connected devices are powered, via two additional wires, by either the host FACP or a remote UL-listed, filtered power supply. N-ANN-80 is black; for white order N-ANN-80-W. The N-ANN-80 displays English-language text of system point information including device type, zone, independent point alarm, trouble or supervisory status, as well as any custom alpha labels programmed into the control panel. It includes con- trol switches for remote control of critical system functions. (A keyswitch prevents unauthorized operation of the control switches.) Up to eight N-ANN-805 may be connected to the ANN-BUS of each FACP. Minimal programming is required, which saves time during system commissioning. The N-ANN-80 is compatible with NOTIFIER FACP5 with an ANN-BUS, such as the NFW-50. Features Listed to UL Standard 864, 9th Edition. Backlit 80-character LCD display (20 characters x 4 lines). Mimics all display information from the host panel. Control switches for System Acknowledge, Signal Silence, Drill, and Reset. Control switches can be independently enabled or disabled at the FACP. Keyswitch enables/disables control switches and mechani- cally locks annunciator enclosure Keyswitch can be enabled or disabled at the FACP. Enclosure supervised for tamper. System status LEDs for AC Power, Alarm, Trouble, Supervi- sory, and Alarm Silence. Local sounder can be enabled or disabled at the FACP. N-ANN-80 connects to the ANN-BUS terminal on the FACP and requires minimal panel programming. Displays device type identifiers, individual point alarm, trou- ble, supervisory, zone, and custom alpha labels. Time-and date display field. Surface mount directly to wall or to single, double, or 4' square electrical box. Semi-flush mount to single, double, or 4' square electrical box. Use ANN-SB80K1T for angled view mounting. Can be remotely located up to 6,000 feet (1,800 m) from the panel. Backlight turns off during AC loss to conserve battery power but will turn back on if an alarm condition occurs. May be powered by 24 VDC from the host FACP or by remote power supply (requires 24 VDC). Up to eight N-ANN-805 can be connected on the ANN-BUS. Controls and Indicators AC Power Alarm Trouble Supervisory Alarm Silenced Specifications Operating voltage range: 18 VDC to 28 VDC. Current consumption @ 24 VDC nominal (filtered and non- resetlable): 40 mA maximum. Ambient temperature: 32°F to 120°F (0°C to 49°C). Relative humidity: 93% ± 2% RH (noncondensing) at 32°C ± 2°C (90°F ± 3°F). 5.375" (13.65 cm.) high x 6.875" (17.46 cm.) wide x 1.375" (3.49 cm.) deep. For use indoors in a dry location. All connections are power-limited and supervised. Agency Listings and Approvals The listings and approvals below apply to the N-ANN-80. In some cases, certain modules may not be listed by certain approval agencies, or listing may be in process. Consult factory for latest listing status. UL: S635 FM approved CSFM: 7120-0028:240 MEA: 442-06-E Vol. 2 The ANN-BUS POWERING THE DEVICES ON THE ANN-BUS FROM AUXILIARY POWER SUPPLY The ANN-BUS can be powered by an auxiliary power supply when the maximum number of ANN-BUS devices exceeds the ANN-BUS power requirements. See the FACP manual for more information. dn-71 I 4:c • 5/22/09 - Page 1 of 2 ANN-BUS DEVICE ADDRESSING Each ANN-BUS device requires a unique address (ID Number) in order to communicate with the FACP. A maximum of 8 devices can be connected to the FACP ANN-BUS communication circuit. See the FACP manual for more information. WIRE REQUIREMENTS: COMMUNICATIONS CIRCUIT The N-ANN-80 connects to the FACP ANN-BUS communica- tions circuit. To determine the type of wire and the maximum wir- ing distance that can be used with FACP ANN-BUS accessory modules, it is necessary to calculate the total worst case current draw for all modules on a single 4-conductor bus. The total worst case current draw is calculated by adding the individual worst case currents for each module. NOTE: For total worst case current draw on a single ANN-BUS refer to appropriate FACP manual. After calculating the total worst case current draw, the following table specifies the maximum distance the modules can be located from the FACP on a single wire run. The table ensures 6.0 volts of line drop maximum. In general, the wire length is lim- ited by resistance, but for heavier wire gauges, capacitance is the limiting factor. These cases are marked in the chart with an asterisk (*)• Maxi- mum length can never be more than 6,000 feet (1,800 m), regardless of gauge used. See table below. WIRE REQUIREMENTS: POWER CIRCUIT 14 to 18 AWG (0.75 - 2.08 mm2) wire for 24 VDC power cir- cuit is acceptable. All connections are power-limited and supervised. A maximum of eight N-ANN-80 modules may be connected to this circuit. Communication Pair Wiring Distance: FACP to Last ANN-BUS Module Total Worst Case Current Draw (amps) 22 Gauge 18 Gauge 16 Gauge 14 Gauge 0.100 1,852 ft. 4,688 ft. 6,000 ft. -6,000 ft. 0.200 926 ft. 2,344 ft. 3,731 ft. 5,906 ft. 0.300 617 ft. 1,563 ft. 2,488 ft. 3,937 ft. 0.400 463 ft. 1,172 ft. 1,866 ft. 2,953 ft. 0.500 370 ft. 938 ft. 1,493 ft. 2,362 ft. 0.600 309 ft. 781 ft. 1,244 ft. 1,969 ft. 0.700 265 ft. 670 ft. 1,066 ft. 1,687 ft. 0.800 231 ft. 586 ft. 933 ft. 1,476 ft. 0.900 206 ft. 521 ft. 829 ft. 1,312 ft. 1.000 (max.) 185 ft. 469 ft. 746 ft. 1,181 ft. WIRING CONFIGURATION The following figure illustrates the wiring between the FACP and ANN-BUS devices. ANN-BUS and power wiring are supervised and power-limited. TB1 11 ORDERING OPTIONS: N-ANN-80: Black 80 character LCD Annunciator. N-ANN-80-W: White, 80 character LCD Annunciator. ANN-SB80K1T-B: Black surface mount backbox with angled wedge. ANN-SB80K1T-W: White surface mount backbox with angled wedge. FACP Wiring to ANN-BUS Device ©2009 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited. ISO 9001 This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. I . We cannot cover all specific applications or anticipate all requirements. I I ____ ____ ENGINEERING MANUFACTURING QUALITY SYSTEMS All specifications are subject to change without notice. I I Made in the U.S. A. For more information, contact Notifier. Phone: (203)484-7161, FAX: (203) 484-7118. www.notifier.com Page 2 of 2— dn-71 14:c • 5/22/09 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7120-0028:0240 Page 1 of 1 CATEGORY: 7120--ANNUNCIATORS LISTEE: NotifierOne Fire-Lite Place, Northford, CT 06472-1653 Contact: Vladimir Kireyev (203) 484-6277 Fax (203) 484-7309 Email: vladimir.kireyev©honeywell.com DESIGN: Models N-ANN-80 and *NANN80W remote fire annunciators. Unit is a 80-character, supervised backlit LCD fire annunciator. Communication between the control panel and the annunciator is accomplished over a two-wire serial interface employing the ANN-BUS protocol. Refer to listee's data sheet for additional detailed product description and operational considerations. INSTALLATION: In accordance with listee's printed installation instructions, applicable codes & ordinances and in manner acceptable to the authority having jurisdiction. MARKING: Listee's name, product number, electrical rating and UL label. APPROVAL: Listed as an annunciator for use separately listed compatible fire alarm control units. Refer to manufacturer's installation manual for details. XLF: 7120-0075:0211 *Rev 12-11-14 gt This listng is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2015 Listing Expires June 30, 2016 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division (i n) Ov Of wg,Thrii Add network communication to Extend the Life and expand the capabilities of older panels by adding the power of advanced network communication. With this simple communications add-on, almost every panel can take advantage of revenue-building remote system management and control features. Provide central station communication over network for any panel Use Contact ID capture. 4 slaves zones, or Bell Monitoring iComSLTM enables basic remote panel control via Virtual Keypad AppTM Provides end user alerts of arming/ disarming, alarm, and other events Add Z-Wave control of lights, Locks, and thermostats with iComSLZTM iCom S - ES 1 R ALARM UNI CATOR. SYSTEM FE1U Fully supervised network alarm communication Program your own account number to easily workaround locked panels Contact ID dialer capture Four zones or Bell Monitoring Wiring for Ademco ECP Bus Communicates with DMP SCS-IR and SCS-VR Receivers Builds customer loyalty; creates new RMR Armed/disarmed status LED Private labeling available on the rubber logo insert Two outputs WORKS WITH MOST PANELS If the existing panel supports Contact ID capture cr4 slave zones, then it's a candidate for upgrading with the iComSL or iComSLZ. There are no issues with lockout codes. Simply add the iComSL unit to the existing installation and program in your own account number. AVAILABLE MODELS The iComSL provides control of basic panel security functions and video. The iComSLZ adds the ability to remotely interact with Z-Wave devices, enabling a variety of home automation features including control of lights, door locks, thermostats and more. FIRE COMMUNICATION The iComSLF offers network fire communication on any fire control panel via Contact ID Captures or Zone Inputs. Meets NFPA 72 Standard for Single Communication Technology. MOBILE SYSTEM CONTROL With iComSL communicators you can easily update your older residential and commercial customers to the latest network communication links. With network in place, end users can remotely access their panels via the Virtual Keypad AppTM. This makes it possible to use their mobile device not only to control basic arm/disarm functions and receive alerts, but also to control Z-Wave home automation devices for lights, door locks, thermostats, and more with iComSLZ. ENABLE VIDEO ON THE APP Video is no longer an expensive option. With the iComSL communicators, you can easily add up to six wireless cameras. Via the Virtual Keypad App, end users can do a remote visual survey of their premises to confirm an alarm or simply check in on children or senior adults. Users can also capture still or video images. FULLY SUPERVISED COMMUNICATION Provides a fully supervised alarm communication path for burglary control panels over the network connection providing higher speeds. iComSL allows alarm messages to be communicated to an SCS-1 R or SCS-VR Receiver. FIELD PANEL UPDATES The Model 400 USB Flash Module allows you to easily field update firmware for panels that would otherwise require the use of a computer and a Model 399 Programming Harness. MULTIPLE CONNECTION OPTIONS iComSL communicators can be attached to the existing panel in a variety of ways. It can capture Contact ID messages from the dialer, or connect the four input zones from outputs on the panel; or it can sense the output of the bell of an existing alarm and communicate the appropriate message to the Central Station. FOUR ZONES Both of the iComSL models provide four zones for connection to burglary control panel outputs. Zone 4 is intended for connection to the control panel bell output. EASY UPGRADE FOR DIALER ONLY PANELS Older, dial-up panels have new life with the addition of network communication. Earn customer loyalty by extending the life of their existing panels, enabling them to increase the ROI on their system investment and build satisfaction with the purchase decision. BUILD CUSTOMER LOYALTY Avoid the possibility of customers seeking mobile intrusion alarm features from a competitor by enabling those features on their existing panel with a minimal additional cost. They are less likely to switch systems and cancel their contract. When the time does come to replace the panel, they are more likely to rely on you. The app can be branded with your organizations logo and contact information to provide a daily reminder of your services. OUTPUTS Use outputs to connect to an arming zone of an existing panel for control of that panel via the App. SPEC ICA)NS Dimensions: 5.5 Wx3.75 H xl" 0 Color: White Open-Collector Outputs: 2 Zones: 4 Primary Power (iComSL/SLZ): 12VDC Primary Power (iComSLF): 1224VDC Current Draw: Alarm 210 mA Standby 210 mA iComSL Network Alarm Communicator iComSLF Network Fire Alarm Communicator iComSLZ Network Alarm Communicator, Z-Wave For approval information, access www.dmp.com and select Compliance. k 2500 North Partnership Boulevard Springfield, Missouri 65803-8877 800.6414282 dmp.com Designed. Engineered & Manufactured in Springfield, Missouri CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION 11 OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7300-1157:0136 Page 1 of 1 CATEGORY: 7300-- FIRE ALARM CONTROL UNIT ACCESSORIES/MISC. DEVICES LISTEE: Digital Monitoring Products2500 N. Partnership Blvd, Springfield, MO 65803 Contact: Terry Shelton (417) 831-9362 Fax (417) 831-1325 Email: tshelton@dmp.com DESIGN: Models CellComSLC, CellComSLCZ, *CeIIComSLCF* iComSLF, iCOMSL and iComSLZ Communicators. Refer to listee's data sheet for additional detailed product description and operational considerations and listee's installation instructions for details. RATING: 12 VDC or 24 VDC INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listees name, model number, electrical rating and ETL label. APPROVAL: Listed as alarm communicators for use with separately listed fire and burglary alarm control units. For indoor use only. Refer to listee's Installation Instruction Manual for details. Burglary and other non-fire functions were not examined. *Rev. 07-14-15 gt This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2015 Listing Expires June 30, 2016 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division NP-100 with B7IOLP base NP-lOOT with B7IOLP base NP-100(A), NP-I OOT(A), NP-I OOR(A) Addressable Photoelectric Detectors dn-6995:b • Al -320 NOTIFIER® for the FireWarden Series by Honeywell General The NP-100 and NP-100T addressable, low-profile plug-in photoelectric detectors use a state-of-the-art photoelectric sensing chamber with communications to provide open area protection and are used exclusively with NOTIFIER's Fire War- den Series (FireWarden-100-2 and FireWarden-50) Address- able Fire Alarm Control Panels (FACP5). The NP-100T adds thermal sensors that will alarm at a fixed temperature of 135°F (57°C). Since these detectors are addressable, they will help emergency personnel quickly locate a fire during its early stages, potentially saving precious rescue time while also reducing property damage. Two LEDs on each sensor light to provide a local, visible sensor indication. Remote LED annun- ciator capability is available as an optional accessory (P/N RA100Z(A)). The NP-i OOR is a remote test capable detector for use with DNR(W) duct smoke detector housings. Features SLC loop: Two-wire loop connection. Unit uses base for wiring. Addressing: Addressable by device. Direct Decade entry of address: 01 - 99 with FireWarden- 100-2, and 01 - 50 with Fire Warden-SO. Architecture: Unique single-source, dual-chamber design to respond quickly and dependably to a broad range of fires. Sleek, low-profile design. Applications Integral communications and built-in type identification. Use photoelectric detectors in life-safety applications to pro- Built-in tamper-resistant feature. vide a broad range of fire-sensing capability, especially where smoldering fires are anticipated. Ionization detectors are often Removable cover and insect-resistant screen for simple better than photoelectric detectors at sensing fast, flaming field cleaning, fires. Operation: Withstands air velocities up to 4,000 feet-per-minute (20 m/ sec.) without triggering a false alarm. Factory preset at 1.5% nominal sensitivity for panel alarm threshold level. Visible LED "blinks" when the unit is addressed (communi- cating with the fire panel) and latches on in alarm. Mechanicals: Sealed against back pressure. Direct surface mounting or electrical box mounting. Mounts to: single-gang box, 3.5" (8.89 cm) or 4.0" (10.16 cm) octagonal box, or 4.0" (10.16 cm) square electrical box (using a plaster ring - included). Other system features: Fully coated circuit boards and superior RF/transient pro- tection. 94-VU plastic flammability rating. Low standby current. Options: Remote LED output connection (P/N RA1 OOZ). Construction These detectors are constructed of off-white LEXAN®. NP-100(T) plug-in, low-profile smoke detectors are designed to commercial standards and offer an attractive appearance. Installation NP-100(T) plug-in detectors use a detachable mounting base to simplify installation, service and maintenance. Mount base on box which is at least 1.5 inches (3.81 cm) deep. Suitable boxes include: 4.0° (10.16 cm) square box with plaster ring. 4.0" (10.16 cm) octagonal box. 3.5" (8.89 cm) octagonal box. Single-gang box. NOTE: Because of the inherent supervision provided by the SLC loop, end-of-line resistors are not required. Wiring '7-taps" or branches are permitted for Style 4 (Class B) wiring. NP-lOOP mounts in a DNR(W) duct detector housing. dn-6995:b • 3/12/10 — Page 1 of 2 Operation Each NP-1001T/R uses one of 99 possible addresses on the FireWarden-100-2 and one of 50 possible addresses on the FireWarden-50 Signaling Line Circuit (SLC). It responds to regular polls from the system and reports its type and status. The NP-i 00/T/R addressable photoelectric sensor's unique unipolar chamber responds quickly and uniformly to a broad range of smoke conditions and can withstand wind gusts up to 4,000 feet-per-minute (20 rn/sec.) without sending an alarm level signal. Because of its unipolar chamber, the NP-100/T/R is approximately two times more responsive than most photo- electric sensors. This makes it a more stable detector. Detector Sensitivity Test Each detector can have its sensitivity tested (required per NFPA 72, Chapter 14 on Inspection, Testing and Maintenance) when installed/connected to a FireWarden-100-2 or FireWar- den-SO addressable fire alarm control panel. The results of the sensitivity test can be printed off the Fire Warden-100-2 or Fire- Warden-SO for record keeping. Specification Voltage range: 15-32 VDC (peak). Standby current: 300 pA @ 24 VDC. LED current: 6.5 mA © 24 VDC (latched "ON"). Air velocity: 4,000 ft/mm. (20 rn/sec.) maximum. Diameter: 6.1" (15.5 cm) installed in B71OLP base. Height: 2.1" (5.33 cm) installed in B71OLP base. Weight: 3.6 oz. (102 g). Operating temperature range: for NP-100: 0°C to 49°C (32°F to 120°F); for NP-100T.O°C to 38°C (32°F to 100°F). NP-100R: installed in a DNR(W) -20°C to 70°C (-4°F to 158°F). Temperature: 0°C - 49°C (32°F - 120°F). Relative humidity: 10% - 93%, non-condensing. Listings Listings and approvals below apply to the NP-100 and NP- 100T detectors. In some cases, certain modules may not be listed by certain approval agencies, or listing may be in pro- cess. Consult factory for latest listing status. UL Listed, file S1115. CSFM approved: file 7272-0028:231. MEA approved: file 243-02-E Vol. 2. Maryland State Fire Marshal: permit 2173. FM approved. Product Line Information NP-100: Adressable photoelectric detector; B71OLP base included. NP-i OOA: Sarnes as NP-100 with ULC Listing (B710LPA base included). NP-lOOT: Same as NP-100 but with thermal element; B71OLP base included. NP-lOOTA: Same as NP-100T with ULC Listing (B710LPAbase included). NP-100R: Remote test capable addressable photoelectric detector for use with a DNR(W) duct detector housing. B71OLP: Plug-in detector base. Dimensions: 6.1" (15.5 cm). Mounting: 4.0" (10.16 cm) square box with or without plaster ring, 4.0" (10.16 cm) octagonal box, 3.5" (8.89 cm) octagonal box, or single-gang box. All mounting boxes have a minimum depth of 1.5" (3.81 cm). B224RB: Plug-in System Sensor relay detector base. Diame- ter: 6.2" (15.75 cm). Mounting: 4.0" (10.16 cm) square box with or without plaster ring, 4.0" (10.16 cm) octagonal box, or 3.5" (8.89 cm) octagonal box. All mounting boxes have a mini- mum depth of 1.5" (3.81 cm). B224B1: Plug-in System Sensor isolator detector base. Maxi- mum 25 devices between isolator bases (see DN-6994). Diameter. 6.2" (15.75 cm). Mounting: 4.0" (10.16 cm) square box with or without plaster ring, 4.0" (10.16 cm) octagonal box, or 3.5" (8.89 cm) octagonal box. All mounting boxes have a minimum depth of 1.5" (3.81 cm). B200SR: Sounder base capable of producing temporal-3 or steady sound output. ACCESSORIES: RA100Z(A): Remote LED annunciator. 3-32 VDC. Mounts to a U.S. single-gang electrical box. For use with B501 and B71OLP bases only. SMK400E: Surface mounting kit provides for entry of surface wiring conduit. For use with B501 base only. RMK400: Recessed mounting kit. For use with B501 base only. M02-04-00:Test magnet. M02-09-00: Test magnet with telescoping handle. XR213: Detector removal tool. Allows installation and/or removal of detector heads from bases in high ceiling applications. XP-4: Extension pole for XR28. Comes in three 5-foot (1.524 m) sections. T55-127-01O:Detector removal tool without pole. BCK-200B: Black detector covers, box of 10. WCK-200B: White detector covers, box of 10. NOTIFIER® is a registered trademark of Honeywell International Inc. Bayblend® is a registered trademark of Bayer Corporation. 02008 by Honeywell International Inc. All rights reserved, unauthorized use of this document is strictly prohibited. I So gooi This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. ENGINEERING MANUFACTURING All specifications are subject to change without notice. QUALITY SYSTEMS For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118. www.notifier.com Page 2 of 2- dn-6995:b • 3/12110 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7272-0028:0231 Page 1 of 1 CATEGORY: 7272 -- SMOKE DETECTOR-SYSTEM TYPE-PHOTOELECTRIC LISTEE: NotifierOne Fire-Lite Place, Northford, CT 06472-1653 Contact: Vladimir Kireyev (203) 484-6277 Fax (203) 484-7309 Email: vladimir.kireyev@honeywell.com DESIGN: Models NP-100, NP100R* and NP-100T photoelectric type smoke detectors. Model NP-lOOT has a 135°F supplement integral heat sensor which only assists in a fire situation. The purpose of this thermal circuitry is to increase the sensitivity of the detector. This thermal circuitry is NOT approved for use as a heat detector. Refer to listee's printed data sheet for additional detailed product description and operational considerations. RATING: 24VDC INSTALLATION: In accordance with listee's printed installation instructions, applicable codes & ordinances and a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating and UL label. APPROVAL: Listed as photoelectric smoke detector for use with separately listed compatible fire alarm control units and bases. All models are suitable for open areas and inside duct installations with air velocities between 0- 4000 FPM. *Models NP-100 and NP-100R are also approved for installations inside Notifier duct detector housing ND-200 (OSFM Listing No. 3242-0028:236) and System Sensor duct detector housing DNRW (OSFM Listing No. 3242-1653:210). Refer to listee's Installation Instruction Manual for details. NOTE: The photoelectric type detectors are generally more effective at detecting slow, smoldering fires, which smolder for hours before bursting into flames. Sources of these fires may include cigarettes burning in couches or bedding. The ionization type detectors are generally more effective at detecting fast, flaming fires, which consume combustible materials rapidly and spread quickly. Sources of these fires may include paper burning in a waste container or a grease fire in the kitchen. XLF: 7272-0075:0194 *Rev. 01-27-10fm This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed SJ the test results and/or other data but does not make an independent verification of any claims. This listing is not an endcrsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2015 Listing Expires June 30, 2016 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division NOT-BGI 2LX Addressable Manual Pull Station DN-7001:D • Al -380 *11~ S - Honeywell by The Notifier NOT-BG12LX is a state-of-the-art, dual-action (i.e., requires two motions to activate the station) pull station that includes an addressable interface for FireWarden series intelligent control panels, and the NSP-25 panel. Because the NOT-BG12LX is addressable, the control panel can display the exact location of the activated manual station. This leads fire personnel quickly to the location of the alarm. Features Maintenance personnel can open station for inspection and address setting without causing an alarm condition. Built-in bicolor LED, which is visible through the handle of the station, flashes in normal operation and latches steady red when in alarm. Handle latches in down position and the word "ACTIVATED" appears to clearly indicate the station has been operated. Captive screw terminals wire-ready for easy connection to SLC loop (accepts up to 12 AWG/3.25 mm2 wire). Can be surface mounted (with SB-10 or SB-I/O) or semi- flush mounted. Semi-flush mount to a standard single- gang, double-gang, or 4" (10.16 cm) square electrical box. Smooth dual-action design. Meets ADAAG controls and operating mechanisms guide- lines (Section 4.1.3[13]); meets ADA requirement for 5 lb. maximum activation force. Highly visible. Attractive shape and textured finish. Key reset. Includes Braille text on station handle. Optional trim ring (BG12TR). Meets UL 38, Standard for Manually Actuated Signaling Boxes. Construction Shell, door, and handle are molded of durable polycarbonate material with a textured finish. Specifications Shipping Weight: 9.6 oz. (272.15 g) Normal operating voltage: 24 VDC. Maximum SLC loop voltage: 28.0 VDC. Maximum SLC standby current: 375 pA. Maximum SLC alarm current: 5 mA. Temperature Range: 32°F to 120°F (0°C to 49°C) Relative Humidity: 10% to 93% (noncondensing) For use indoors in a dry location Installation The NOT-BG12LX will mount semi-flush into a single-gang, double-gang, or standard 4" (10.16 cm) square electrical outlet box, or will surface mount to the model SB-10 or SB-I/O sur- face backbox. If the NOT-BG12LX is being semi-flush mounted, then the optional trim ring (BG12TR) may be used. The NOT-BGI2LX Addressable Manual Pull Station The BG12TR is usually needed for semi-flush mounting with 4" (10.16 cm) or double-gang boxes (not with single-gang boxes). Operation Pushing in, then pulling down on the handle causes it to latch in the down/activated position. Once latched, the word "ACTI- VATED" (in bright yellow) appears at the top of the handle, while a portion of the handle protrudes from the bottom of the station. To reset the station, simply unlock the station with the key and pull the door open. This action resets the handle; clos- ing the door automatically resets the switch. Each manual station, on command from the control panel, sends data to the panel representing the state of the manual switch. Two rotary decimal switches allow address settings (1 - 99 on NFW2-100/NFW2-100C, 1 - 50 for N FW-50/N FW- 50C). Architectural/Engineering Specifications Manual Fire Alarm Stations shall be non-coded, with a key- operated reset lock in order that they may be tested, and so designed that after actual Emergency Operation, they cannot be restored to normal except by use of a key. An operated sta- tion shall automatically condition itself so as to be visually detected as activated. Manual stations shall be constructed of red-colored polycarbonate material with clearly visible operat- ing instructions provided on the cover. The word FIRE shall appear on the front of the stations in white letters, 1.00 inches (2.54 cm) or larger. Stations shall be suitable for surface mounting on matching backbox SB-iD or SB-I/O; or semi-flush mounting on a standard single-gang, double-gang, or 4"(10.16 cm) square electrical box, and shall be installed DN-7001:D.4/13/2012—Page 1 0f2 within the limits defined by the Americans with Disabilities Act (ADA) or per national/local requirements. Manual Stations shall be Underwriters Laboratories listed. Manual stations shall connect with two wires to one of the con- trol panel SLC loops. The manual station shall, on command from the control panel, send data to the panel representing the state of the manual switch. Manual stations shall provide address setting by use of rotary decimal switches. Product Line Information NOT-BG12LX: Dual-action addressable pull station. Includes key locking feature. (Listed for Canadian and non-Canadian applications.) SB-10: Surface backbox; metal. SB-I/O: Surface backbox; plastic. BG12TR: Optional trim ring. 17021: Keys, set of two. Agency Listings and Approvals In some cases, certain modules or applications may not be listed by certain approval agencies, or listing may be in pro- cess. Consult factory for latest listing status. UL/ULC Listed: S692 (listed for Canadian and non-Cana- dian applications). MEA: 67-02-E Vol. IV. CSFM: 7150-0028:0199. FM Approved. Patented: U.S. Patent No. D428,351; 6,380,846; 6,314,772; 6,632108. NOTIFIERS is a registered trademark of Honeywell International Inc. ©2012 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited. This document is not intended to be used for installation purposes. I So 0001 We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. ENGINEERING & MANUFACTURING All specifications are subject to change without notice. QUALITY SYSTEMS Made inthe U.S. A. For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118. www.notifier.com Page 2 of 2— DN-7001 :D • 4/13/2012 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7150-0028:0199 Page 1 of 1 CATEGORY: 7150-- FIRE ALARM PULL BOXES LISTEE: NotifierOne Fire-Lite Place, Northford, CT 06472-1653 Contact: Vladimir Kireyev (203) 484-6277 Fax (203) 484-7309 Email: vladimir.kireyevhoneywell.com DESIGN: Models NBG-12, NBG-12S, NBG-12LR, NBG-12LRA, NBG-12LAO, NBG-12LAOB, NBG-12-LO, NBG-12L0B, NBG-12W, NBG-I2LW, NBG-12NC, NBG-I2WP, NBG-I2LWP, NBG-12L, NBG-12LX, NBG-12LA, NBG-12PS, NBG-I2LSP, NBG-12LPS, NBG-12LPSP, NBG-12SP, NOT-BG12LX, NBG-12LXSP, NBG-12LXBL and NBG-12LXP fire alarm pull boxes. All units except Model NBG-125 are dual action pull stations. Models NBG-12LR and NBG-12LRA are intended for agent releasing device. Refer to listee's data sheet for detailed product description and operational considerations. INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, rating, and UL label. APPROVAL: Listed as fire alarm pull boxes for use with separately listed compatible fire alarm control units. Models NBG-12WP, NBG-12LW, NBG-12W, NBG-12LWP, NBG-12LAO, NBG-12L0, NBG-12LAOB and NBG-12L0B are intended for outdoor use when installed with Models WBB, SB-I/O, orWP-10 back box. Refer to listee's Installation Instruction Manual for details. These manual pull boxes meet the requirements of UL Standard 38, 1999 Edition and California amendments which the controls and operating mechanisms required to be operable at no more than 51bs. force with one hand and shall not require tight grasping, pinching, or twisting of the wrist. *Corrected 10-08-12 bh This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2015 Listing Expires June 30, 2016 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division dn-60383:A2 NC-1 OOR(A) NOTI FR ER® Relay Module for FireWarden Series Panels by Honeywell F General The NC-100R(A) Addressable Relay Module provides NOTI- FIER's FireWarden Series intelligent control panels with two isolated sets of Form-C dry-contact outputs for activating a variety of auxiliary devices, such as fans, dampers, door hold- ers, control equipment, etc. Addressability allows the dry con- tact to be activated, either manually or through panel programming, on a select basis. WIN Features Built-in type identification automatically identifies these devices to the control panel. Internal circuitry and relay powered directly by two-wire SLC loop. Integral LED "blinks" green each time a communication is received from the control panel and turns on in steady when activated. High noise immunity (EMF/RFI). Wide viewing angle of LED, SEMS screws with clamping plates for wiring ease. Direct Decade entry of address: 01 - 99 with the FireWar- den-100-2(C) and 01 —50 with 'the FireWarden-50(C). Applications The NC-1 OOR(A) may be programmed to operate dry contacts for door holders, Air Handling Unit shutdown, etc., and to reset four-wire smoke detector power. Construction The face plate is made of off-white heat-resistant plastic. Controls include two rotary switches for direct-dial entry of address setting. The NC-100R(A) provides two Form-C dry contacts that switch together. Operation Each NC-100R(A) uses one of the addresses on a SLC loop. It responds to regular polls from the control panel and reports its type and status. The LED blinks with each poll received. On command, it activates its internal relay. Rotary switches set a unique address for each module. The address may be set before or after mounting. The built-in TYPE CODE (not settable) will identify the module to the con- trol panel. NC-i OOR(A) Specifications Normal operating voltage: 15 to 32 VDC. Maximum SLC current draw: 6.5 mA (LED). Average operating current: 230 pA direct poll (CLIP mode), 255 pA group poll with LED flashing. EOL resistance: not used. Temperature range: 32°F to 120°F (0°C to 490C). Humidity range: 10% to 93% non-condensing. Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x 1.25" (3.175 cm) deep. Mounts to a 4" (10.16 cm) square x 2.125" (5.398 mm) deep box. Relay Contact Ratings Load Description Application Maximum Current Voltage Rating Resistive Non-Coded 30 VDC 3.0 A Resistive Coded 30 VDC 2.0 A Resistive Non-Coded 110 VDC 0.9 A Resistive Non-Coded 125 VAC 0.9A Inductive (L/R=5m5) Coded 30 VDC 0.5 A Inductive (L/R=2ms) Coded 30 VDC 1.0 A Inductive (PF=0.35) Non-Coded 125 VAC 0.5 A dn-60383:A2 • 06/17/10 - Page 1 of 2 Agency Listings and Approvals In some cases, certain modules may not be listed by certain approval agencies, or listing may be in process. Consult fac- tory for latest listing status. ULIULC Listed: S635. CSFM approved: file 7300-0028:230. FM approved. MEA approved: file 72-01-E, Vol. 2. Product Line Information NC-i OOR: 1nte11gent addressable relay module. NC-i OORA: Intelligent addressable relay module, ULC listed model. SMB500: Optional surface-mount backbox. NOTE: For installation instructions, see document /56-2593-001 and refer to the SLC Wiring Manual, document 52304. NOTIFIER® is a registered trademark of Honeywell International Inc. @2010 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is Strictly prohibited. This document is not intended to be used for installation purposes. I SO 9001 We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. ENGINEERING & MANUFACTURING All specifications are subject to change without notice. QUALITY SYSTEMS Made in the U.S. A. For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118. www.notifier.com Page 2 of 2— dn-60383:A2 • 06/17/10 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7300-0028:0230 Page 1 of 1 CATEGORY: 7300-- FIRE ALARM CONTROL UNIT ACCESSORIES/MISC. DEVICES LISTEE: NotifierOne Fire-Lite Place, Northford, CT 06472-1653 Contact: Vladimir Kireyev (203) 484-6277 Fax (203) 484-7309 Email: vladimir.kireyev@honeywell.com DESIGN: Models NMM-100P, NMM-100, and NZM-100 monitor modules; Models NC-100R and NC-100 control modules; and *NzM100..6 six zone interface signaling device module. Refer to listee's data sheet for additional detailed product description and operational considerations. RATING: 15-32 VDC INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listees name, model number, electrical rating, and UL label. APPROVAL: Listed as control unit accessories for use with listee's separately listed electrically compatible fire alarm control units. Refer to listee's Installation Instruction Manual for details. XLF: 7300-0075:0185 08-23-11 rev. mt This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2015 Listing Expires June 30, 2016 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division Monitor Modules DN-6999:C N MM-I 00(A), NMM-1 OOP(A), NOTIFIER® NZM-I00(A). and NDM-100IA1 for FireWarden Series Panels by Honeywell General Four different monitor modules are available for Notifier's Fire- Warden Series intelligent control panels for a variety of appli- cations. Monitor modules supervise a circuit of dry-contact input devices, such as conventional heat detectors and pull stations, or monitor and power a circuit of two-wire smoke detectors (NZM-100(A)). NMM-100(A) is a standard-sized module (typically mounts to a 4" [10.16 cm] square box) that supervises either a Style D (Class A) or Style B (Class B) circuit of dry-contact input devices. NMM-100P(A) is a miniature monitor module a mere 1.3" (3.302 cm) H x 2.75 (6.985 cm) W x 0.5" (1.270 cm) D that supervises a Style B (Class B) circuit of dry-contact input devices. Its compact design allows the NMM-100P(A) to be mounted in a single-gang box behind the device it monitors. NZM-100(A) is a standard-sized module that monitors and supervises compatible two-wire, 24 volt, smoke detectors on a Style D (Class A) or Style B (Class B) circuit. NDM-100(A) is a standard-sized dual monitor module that monitors and supervises two independent two-wire Style B (Class B) dry-contact initiating device circuits (lDCs) at two separate, consecutive addresses in intelligent, two-wire systems. NMM-100(A) Monitor Module Built-in type identification automatically identifies this device as a monitor module to the control panel. Powered directly by two-wire SLC loop. No additional power required. High noise (EMF/RFI) immunity. SEMS screws with clamping plates for ease of wiring. Direct Decade entry of address: 01 - 99 on FireWarden- 100-2, 01 — SOon FireWarden-50. LED flashes during normal operation and latches on steady to indicate alarm. The NMM-100(A) Monitor Module is intended for use in intelli- gent, two-wire systems, where the individual address of each module is selected using the built-in rotary switches. It pro- vides either a two-wire or four-wire fault-tolerant Initiating Device Circuit (IDC) for normally-open-contact fire alarm and supervisory devices. The module has a panel-controlled LED indicator. NMM-100(A) APPLICATIONS Use to monitor a zone of four-wire smoke detectors, manual fire alarm pull stations, waterflow devices, or other normally- open dry-contact alarm activation devices. May also be used to monitor normally-open supervisory devices with special supervisory indication at the control panel. Monitored circuit may be wired as an NFPA Style B (Class B) or Style D (Class A) Initiating Device Circuit. A 47K ohm End-of-Line Resistor (provided) terminates the Style B circuit. No resistor is required for supervision of the Style D circuit. c Le" TI SUP Aj-j PLC TITUPAI+I flMOCILUFLASIL NMM-100(A) (Type H) NMM-100(A) OPERATION Each NMM-100(A) uses one of the available module addresses on an SLC loop. It responds to regular polls from the control panel and reports its type and the status (open/nor- mal/short) of its Initiating Device Circuit (IDC). A flashing LED indicates that the module is in communication with the control panel. The LED latches steady on alarm (subject to current limitations on the loop). NMM-100(A) SPECIFICATIONS Nominal operating voltage: 15 to 32 VDC. Maximum current draw: 5.0 mA (LED on). Average operating current: 350 I.JA (LED flashing), 1 com- munication every 5 seconds, 47k EOL. Maximum IDC wiring resistance: 40 ohms. EOL resistance: 47K ohms. Temperature range: 32°F to 120°F (0°C to 49°C). Humidity range: 10% to 93% noncondensing. Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x 1.25" (3.175 cm) deep. Mounts to a 4" (10.16 cm) square x 2.125" (5.398 cm) deep box. DN-6999:C • 10/06/2010 - Page 1 of 4 NMM.IOOP(A) Mini Monitor Module Built-in type identification automatically identifies this device as a monitor module to the panel. Powered directly by two-wire SLC loop. No additional power required. High noise (EMF/RFI) immunity. Tinned, stripped leads for ease of wiring. Direct Decade entry of address: 01 - 99 on FireWarden- 100-2, 01 —50 on FireWarden-50. 1415 0 1 ADDRESS I 1 ,2 "" LOOP Ii 3(/2 __1 2 10 5 I _ I 8 76 I 8 76 I TENS ONES The NMM-100P(A) Mini Monitor Module can be installed in a single-gang junction directly behind the monitored unit. Its small size and light weight allow it to be installed without rigid mounting. The NMM-100P(A) is intended for use in intelligent, two-wire systems where the individual address of each module is selected using rotary switches. It provides a two-wire initiat- ing device circuit for normally-open-contact fire alarm and security devices. NMM-100P(A) NMM-IOOP(A) APPLICATIONS Use to monitor a single device or a zone of four-wire smoke detectors, manual fire alarm pull stations, waterflow devices, or other normally-open dry-contact devices. May also be used to monitor normally-open supervisory devices with special super- visory indication at the control panel. Monitored circuit/device is wired as an NFPA Style B (Class B) Initiating Device Circuit. A 47K ohm End-of-Line Resistor (provided) terminates the cir- cuit. NMM-100P(A) OPERATION Each NMM-100P(A) uses one of the available module addresses on an SLC loop. It responds to regular polls from the control panel and reports its type and the status (open/nor- mal/short) of its Initiating Device Circuit (IDC). NMM-100P(A) SPECIFICATIONS Nominal operating voltage: 15 to 32 VDC. Average operating current: 350 pA, 1 communication every 5 seconds, 47k EOL; 600 pA Max. (Communicating, IDC Shorted). Maximum IDC wiring resistance: 40 ohms. Maximum IDC Voltage: 11 Volts. Maximum IDC Current: 400 pA. EOL resistance: 47K ohms. Temperature range: 32°F to 120°F (0°C to 49°C). Humidity range: 10% to 93% noncondensing. Dimensions: 1.3' (3.302 cm) high x 2.75" (6.985 cm) wide x 0.65" (1.651 cm) deep. Wire length: 6" (15.24 cm) minimum. NZM.1 00(A) Interface Module Supports compatible two-wire smoke detectors. Supervises IDC wiring and connection of external power source. High noise (EMF/RFI) immunity. SEMS screws with clamping plates for ease of wiring. Direct Decade entry of address:, 01 - 99 on FireWarden- 100-2, 01 —50 on FireWarden-50. LED flashes during normal operation. LED latches steady to indicate alarm on command from control panel. The NZM-100(A) Interface Module is intended for use in intelli- gent, addressable systems, where the individual address of each module is selected using built-in rotary switches. This module allows intelligent panels to interface and monitor two- wire conventional smoke detectors. It transmits the status (nor- mal, open, or alarm) of one full zone of conventional detectors back to the control panel. All two-wire detectors being moni- tored must be UL compatible with the module. NZM-100(A) APPLICATIONS Use the NZM-100(A) to monitor a zone of two-wire smoke detectors. The monitored circuit may be wired as an NFPA Style B (Class B) or Style D (Class A) Initiating Device Circuit. A 3.9 K ohm End-of-Line Resistor (provided) terminates the end of the Style B or D (class B or A) circuit (maximum IDC loop resistance is 25 ohms). Install ELR across terminals 8 and 9 for Style D application. NZM-100(A) OPERATION Each NZM-100(A) uses one of the available module addresses on an SLC loop. It responds to regular polls from the control panel and reports its type and the status (open/nor- mal/short) of its Initiating Device Circuit (IDC). A flashing LED indicates that the module is in communication with the control panel. The LED latches steady on alarm (subject to current limitations on the loop). NZM-100(A) SPECIFICATIONS Nominal operating voltage: 15 to 32 VDC. Maximum current draw: 5.1 mA (LED on). Maximum IDC wiring resistance: 25 ohms. Average operating current: 300 pA, 1 communication and 1 LED flash every 5 seconds, 3.9k eol. EOL resistance: 3.9K ohms. External supply voltage (between Terminals T3 and T4): DC voltage: 24 volts power limited. Ripple voltage: 0.1 Vrms maximum. Current: 90 mA per module maximum. Temperature range: 32°F to 120°F (0°C to 49°C). Humidity range: 10% to 93% noncondensing. Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x 1.25" (3.175 cm) deep. Mounts to a 4" (10.16 cm) square x 2.125" (5.398 cm) deep box. Page 2 of 4— DN-6999:C • 10/06/2010 NDM-100(A) Dual Monitor Module The NDM-100(A) Dual Monitor Module is intended for use in intelligent, two-wire systems. It provides two independent two- wire initiating device circuits (lDCs) at two separate, consecutive addresses. It is capable of monitoring normally open contact fire alarm and supervisory devices. The module has a single panel- controlled LED. NOTE: The NDM-100(A) provides two Style B (Class B) lOG cir- cuits ONLY Style D (Class A) lOG circuits are NOT supported in any application. NDM-100(A) SPECIFICATIONS Normal operating voltage range: 15 to 32 VDC. Maximum current draw: 6.4 mA (LED on). Average operating current: 750 IJA (LED flashing). Maximum IDC wiring resistance: 1,500 ohms. Maximum IDC Voltage: 11 Volts. Maximum IDC Current: 240 pA EOL resistance: 47K ohms. Maximum SLC Wiring resistance: 40 Ohms. Temperature range: 32° to 120°F (01 to 490C). Humidity range: 10% to 93% (non-condensing). Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x 2.125" (5.398 Cm) deep. NDM-100(A) AUTOMATIC ADDRESSING The NDM-100(A) automatically assigns itself to two address- able points, starting with the original address. For example, if the NDM-100(A) is set to address "26", then it will automati- cally assign itself to addresses "26" and "27". NOTE: "Ones" addresses on the NDM-100(A) are 0, 2, 4, 6, or 8 only. Terminals 6 and 7 use the first address, and terminals 8 and 9 use the second address. CAUTION: Avoid duplicating addresses on the system. Installation NMM-100(A), NZM-100(A), and NDM-100(A) modules mount directly to a standard 4" (10.16 cm) square, 2.125" (5.398 cm) deep, electrical box. They may also be mounted to the SMBSOO surface-mount box. Mounting hardware and installa- tion instructions are provided with each module. All wiring must conform to applicable local codes, ordinances, and regu- lations. These modules are intended for power-limited wiring only. The NMM-100P(A) module is intended to be wired and mounted without rigid connections inside a standard electrical box. All wiring must conform to applicable local codes, ordi- nances, and regulations. Agency Listings and Approvals In some cases, certain modules may not be listed by certain approval agencies, or listing may be in process. Consult fac- tory for latest listing status. UL: S635 ULC: S635 FM Approved CSFM: 7300-0028:0230 (NMM-100, NMM-100P, NZM- 100); 7300-0028:0237 (NDM-100) MEA: 72-01-E Vol. 2 (NMM-100, NMM-100P, NZM-100); 227-03-E Vol. 3 (NDM-100) Product Line Information NOTE: 'A" suffix indicates ULC-listed model. NMM-100(A): Monitor module. NMM-100P(A): Monitor module, miniature. NZM-1 00(A): Monitor module, two-wire detectors. NDM-100(A): Monitor module, dual, two independent Class B circuits. SMB500: Optional surface-mount backbox. NOTE: See installation instructions and refer to the SLC Wiring Manual, PN 52304. DN-6999:C • 10/06/2010 - Page 3 of 4 Notifier® and FireWarden® are registered trademarks and FireWatch is a trademark of Honeywell International Inc. ©2010 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited. This document is not intended to be used for installation purposes. I So 9001 Im We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. DtGINEERIN & MMfIIFACTURING All specifications are subject to change without notice. QUALITY SYSTEMS Made in the U.S. A. For more information, contact Notifier. Phone: (203)484-7161, FAX: (203) 484-7118. www.notifier.com Page 4 of 4— DN-6999:C • 10/06/2010 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7300-0028:0230 Page 1 of 1 CATEGORY: 7300 -- FIRE ALARM CONTROL UNIT ACCESSORIES/MISC. DEVICES LISTEE: NotifierOne Fire-Lite Place, Northford, CT 06472-1653 Contact: Vladimir Kireyev (203) 484-6277 Fax (203) 484-7309 Email: vladimir.kireyev@honeywell.com DESIGN: Models NMM-100P, NMM-100, and NZM-100 monitor modules; Models NC-100R and NC-100 control modules; and *NZM.100.6 six zone interface signaling device module. Refer to listee's data sheet for additional detailed product description and operational considerations. RATING: 15-32 VDC INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating, and UL label. APPROVAL: Listed as control unit accessories for use with listee's separately listed electrically compatible fire alarm control units. Refer to listee's Installation Instruction Manual for details. XLF: 7300-0075:0185 08-23-11 rev. mt This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2015 Listing Expires June 30, 2016 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division Ii S Indoor Selectable. Output Speaker Strobes and Dual Voltage Evacuation Speakers for Ceiling Applications SpectrA lertO Advance selectable-output speaker strobes and dual-voltage evacuation speakers can reduce ground faults and enable faster installation. Features Plug-in design and protective cover reduce ground faults Universal mounting plate with an onboard shorting spring tests wiring continuity before installation No extension ring required Field selectable candela settings: Standard: 15, 15/7530,7595,110,115 High: 135, 150, 177, 185 Automatic selection of 12- or 24-volt operation at 15 and 15/75 candela Rotary switch simplifies field selection of speaker voltage (25 and 70.7 Vrms) and power settings (1/4, ½, 1 and 2 watts) SF speakers offer high fidelity sound output SFV speakers offer high volume sound output Compatible with System Sensor synchronization protocol Electrical compatibility with existing SpectrAlert products Optional tamper resistant Torx head screw included Listed for ceiling Dr wall mounting Agency Listings SIGNALING ® .. MEA LISTED approved S4048 1320.1653:211 10-08-E lrmk'~" " 1, "1 ' F=7; ; The SpectrAlert Advance Series of speakers and speaker strobes reduce costly ground faults using a plug-in design and universal mounting plate that allow the installer to pre-wire mounting plates, dress the wires, and confirm wiring continuity before plugging in the speakers. In addition, a protective plastic cover prevents nicked wires by covering exposed speaker components. These devices also enable faster installations by providing instant feedback to ensure that wiring is properly connected, rotary switches to select voltage and power settings, and 11 field-selectable candela settings for both wall and ceiling speaker strobes. The low total harmonic distortion of the SF speaker offers high fidelity Sound output while the SPV speaker offers high volume sound output for use in high ambient noise applications. SpectrAlert Advance makes installation easy 'Attach a universal mounting plate to a 4 x 4 x 21M inch back box. Flush-mount applications do not require an extension ring. Connect the notification appliance circuit or speaker wiring to the terminals on the mounting plate. Attach the speaker or speaker strobe to the mounting plate by inserting the product tabs into the mounting plate grooves. Rotate the device into position to lock the product pins into the mounting plate terminals. The device will temporarily hold in place with a catch until it is secured with a captured mounting screw, SpectrAlert Advance Speaker and Speaker Strobe Specifications General SpectrAlert Advance speaker and speaker strobes shall mount to a 4 x 4 x 21,8-inch back box. A universal mounting plate shall be used for mounting ceiling and wall products. The notification appliance circuit and amplifier wiring shall terminate at the universal mounting plate. Also SpectrAlert Advance speaker strobes, when used with the Sync-CircUitTM Module accessory, shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts. When used with the Sync.Circuit Module, 12-volt rated notification appliance circuit outputs shall operate between nine and 17.5 volts; 24-volt rated notification appliance circuit outputs shall operate between 17 and 33 volts. Indoor SpectrAlert Advance products shall operate between 32°F and 120°F from a regulated DC, or full-wave rectified, unfiltered power supply. Speaker strobes shall have field-selectable candela settings including 15, 15/75, 30, 75, 95, 110, 115, 135, 150, 177, 185. Speaker The speaker shall be a System Sensor SpectrAlert Advance model dual-voltage transformer speaker capable of operating at 25.0 or 70.7 nominal Vrms. It should be listed to UL 1480 and shall be approved for fire protective service. The speaker shall have a frequency range of 400 to 4,000 Hz and shall have an operating temperature between 32°F and 120°F The speaker shall have power taps and voltage that are selected by rotary switches. Speaker Strobe combination The speaker strobe shall be a System Sensor SpectrAlert Advance model _________ listed to UL1480 and UL 1971 and be approved for fire protective signaling systems. The speaker shall be capable of operating at 25.0 or 70.7 nominal Vrms selected via rotary switch, and shall have a frequency range of 400 to 4,000 Hz. The speaker shall have power taps that are selected by rotary switch. The strobe shall comply with the NFPA 72 requirements for visible signaling appliances, flashing at 1 Hz over the strobe's entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system, Synchronization Module The module shall be a System Sensor Sync-Circuit model MDL listed to UL 464 and shall be approved for fire protective service. The module shall synchronize SpectrAlert strobes at 1 Hz. The module shall mount to a 411/16 x 411/16 x 21,8-inch back box. The module shall also control two Style Y (class B) circuits or one Style Z (class A) circuit. The module shall synchronize multiple zones. Daisy chaining two or more synchronization modules together will synchronize all the zones they control. The module shall not operate on a coded power supply. Operating Temperature 32°F to 120°F (0°C to 49°C) Humidity Range 10 to 93% non-condensing Dimensions, Ceiling-Mount SPS Speaker Strobe 6.8 in Dia. x 4.7 in D (including lens and speaker) SPSV Speaker Strobe 6.8 in Dia. x 4.8 in D (including lens and speaker) SP Speaker 6.8 in Dia. x 2.8 in D SPV Speaker 6.8 in Dia. x 2.9 in D 1I]1.1tiTr3 . ., .1 Nominal Voltage (speakers) 25 Volts or 70.7 Volts (nominal) Maximum Supervisory Voltage (speakers) 50 VDC Strobe Flash Rate 1 flash per second Nominal Voltage (strobes) Regulated 12 V DC/FWR or regulated 24 DC/FWR Operating Voltage Range (includes fire 8 to 17.5 V (12 V nominal) or 16 to 33 V (24 V nominal) alarm panels with built in sync) Operating Voltage with MDL Sync Module 9 to 17.5 V (12 V nominal) or 17 to 33 V (24 V nominal) Frequency Range 400 to 4,000 Hz Power 114.112, 1,2 watts AVDSOO7O1 UL Current Draw Data 8 to 17.5 Volts 16 to 33 Volts Candela DC FWR DC FWR Standard 15 Candela Range 15/75 30 123 142 NA 128 148 NA 66 77 94 71 81 96 75 95 110 NA NA NA NA NA NA 158 181 202 153 176 195 115 NA NA 210 205 High 135 NA NA 228 207 Candela Range 150 NA NA 246 220 177 185 NA NA NA NA 281 286 251 258 UL Reverberant (dBA @ loft.) 2W 1W ½W 1/4 W Ceiling-Mount SPC Series 86 83 80 77 Ceiling-Mount SPCV Series 90 87 84 81 Ceiling-Mount SPSC Series 85 82 79 76 Ceiling-Mount SPSCV Series 89 86 83 80 Dimensions 6.81" I r7- •96H i 6.81" Ceiling-Mount SPV Speaker 6.81 Ceiling-Mount SP Speaker Ceiling-Mount SPS Speaker Strobe AV 0 S 0 07 0 1 Surface Mounting CO Ceiling-Mount Speaker with SPBBSCW Back Box Ordering Information for SpectrAlert® Advance Speakers and Speaker Strobes White Red Description SPCW SPCR Speaker only SPCWV SPCRV Speaker only, High dB SPSCW SPSCR Speaker Strobe, Standard Cd SPSCWH* SPSCRH Speaker Strobe, High Cd SPSCWV SPSCRV Speaker Strobe, Standard Cd, High dB SPSCWVH SPSCRVH Speaker Strobe, High Cd, High dB SPSCW-CLR-ALERT - Speaker Strobe, Standard cd, Clear Lens 1 White Red Description RFPW REP 7 in x 9.5 in Retrofit Plate SPBBSCW SPBBSC Ceiling Mount Back Box Skirt TRCW TAO Ceiling Mount Trim Ring Notes: * Add -P to model number for plain housing (no 'FIRE" marking on the cover) e.g. SPSCW-P 4 "Standard cd' refers to strobes that include 15, 15/75, 30, 75, 95, 110, and 115 candela settings. "High cd' refers to strobes that include 135, 150, 177, and 185 candela settings. TEM 02012 5ysterrn Sensor. ) 3825 Ohio Avenue • St. Charles, IL 60174 Product specifications subject tochurrge without 005ce. Vlsltsysternrsensor.conn i5JtJa5Re Phone' 800-SENSOR2 • Fax' 630-377-6495 for current product information, including the latest version of this data sheet. 1~1 AvDS00701 • 3/12 - - - - --- -. Indoor Selectable. Output Speaker Strobes and Dual Voltage Evacuation Speakers for Wall Applications The SpectrA lertO Advance selectable output speaker strobes and dual-voltage evacuation speakers can reduce ground faults and enable faster installation. Features Plug-in design and protective cover reduce ground faults Universal mounting plate with an onboard shorting spring tests wiring continuity before installation No extension ring required Field selectable candela settings: Standard: 15, 15/753075,95,110,115 High: 135, 150, 177, 185 Automatic selection of 12- or 24-volt operation at 15 and 15/75 candela Rotary switch simplifies field selection of speaker voltage (25 and 70.7 Vrms) and power settings (1/4, ½, 1 and 2 watts) SF speakers offe high fidelity sound output SPV speakers offer high volume sound output Compatible with System Sensor synchronization protocol Electrical compatibility with existing SpectrAlert products Tamper-resistant construction Listed for ceiling or wall mounting Agency Listings SIGNALING ® j.. MEA LISTED LV._.Ji approved S4048 7320-1653:01 10-08.E The SpectrAlert Advance Series of speakers and speaker strobes reduce costly ground faults using a plug-in design and universal mounting plate that allow the installer to pre-wire mounting plates, dress the wires, and confirm wiring continuity before plugging in the speakers. In addition, a protective plastic cover prevents nicked wires by covering exposed speaker components. These devices also enable faster installations by providing instant feedback to ensure that wiring is properly connected, rotary switches to select voltage and power settings, and 11 field-selectable candela settings for both wall and ceiling speaker strobes. The low total harmonic distortion of the SP speaker offers high fidelity sound output while the SPV speaker offers high volume sound output for use in high ambient noise applications. SpectrAlert Advance makes installation easy Attach a universal mounting plate to a 4 x 4 x 21i8 inch back box. Flush-mount applications do not require an extension ring. Connect the notification appliance circuit or speaker wiring to the terminals on the mounting plate. Attach the speaker or speaker strobe to the mounting plate by inserting the product tabs into the mounting plate grooves. Hinge the device into position to lock the product pins into the mounting plate terminals. The device will temporarily hold in place with a catch until it is secured with a captured mounting screw. SpectrAlert Advance Speaker and Speaker Strobe Specifications General SpectrAlert Advance speaker and speaker strobes shall mount to a 4 x 4 x 21j8-inch back box. A universal mounting plate shall be used for mounting ceiling and wall products. The notification appliance circuit and amplifier wiring shall terminate at the universal mounting plate. Also SpectrAlert Advance speaker strobes, when used with the Sync.CircuitTM Module accessory, shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts. When used with the Sync.Circuit Module, 12-volt rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts; 24-volt rated notification appliance circuit outputs shall operate between 16.5 and 33 volts. Indoor SpectrAlert Advance products shall operate between 32°F and 120°F from a regulated DC, or full-wave rectified, unfiltered power supply. Speaker strobes shall have field-selectable candela settings including 15, 15/75, 30, 75, 95, 110, 115, 135, 150, 177, 185. Speaker The speaker shall be a System Sensor SpectrAlert Advance model dual-voltage transformer speaker capable of operating at 25.0 or 70.7 nominal Vrms. It should be listed to UL 1480 and shall be approved for fire protective service. The speaker shall have a frequency range of 400 to 4,000 Hz and shall have an operating temperature between 32°F and 120°F The speaker shall have power taps and voltage that are selected by rotary switches. Speaker Strobe combination The speaker strobe shall be a System Sensor SpectrAlert Advance model _________ listed to UL1480 and UL 1971 and be approved for fire protective signaling systems. The speaker shall be capable of operating at 25.0 or 70.7 nominal Vrms selected via rotary switch, and shall have a frequency range of 400 to 4,000 Hz. The speaker shall have power taps that are selected by rotary switch. The strobe shall comply with the NFPA 72 requirements for visible signaling appliances, flashing at 1 Hz over the strobe's entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system. Synchronization Module The module shall be a System Sensor Sync-Circuit model MDL3 listed to UL 464 and shall be approved for tire protective service. The module shall synchronize SpectrAlert strobes at 1 Hz. The module shall mount to a 411/16 x 411/16 x 21i8-inch back box. The module shall also control two Style Y (class B) circuits or one Style Z (class A) circuit. The module shall synchronize multiple zones. Daisy chaining two or more synchronization modules together will synchronize all the zones they control. The module shall not operate on a coded power supply. .. . . Operating Temperature 32°F to 120°F (0°C to 49°C) Humidity Range 10 to 93% non- condensing Dimensions, Wall-Mount Length Width Depth SP Speaker 6 in, 152 mm Sin, 127 mm 2.8 in, 71 mm SPV Speaker 6 in, 152 mm 5 in, 127 mm 2.9 in, 74 mm With Surface Mount Back Box 6 in, 152 mm 5.1 in, 130 mm 3.4 in, 86 mm SPS Speaker/Strobe (including lens and speaker) 6in, 152 mm 5.1 in, 127 mm 4.7 in, 119 mm With Surface Mount Back Box 6 in, 152 mm 5.1 in, 130 mm 5.325 in, 135 mm ... -,---- Nominal Voltage (speakers) 25 Volts or 70.7 Volts (nominal) Maximum Supervisory Voltage (speakers) 50 VDC Strobe Flash Rate 1 flash per second Nominal Voltage (strobes) Regulated 12 VDC/ F\NR or regulated 24 DC/FWR Operating Voltage Range (includes fire 8 to 17.5 V (12 V alarm panels with built in sync) nominal) or 16 to 33V (24 V nominal) Operating Voltage with MDL3 Sync Module 8.5 to 17.5 V (12 V nominal) or 16.5 to 33V (24 V nominal) Frequency Range 400 to 4000 Hz Power 1/4,1/2, 1, 2 watts UL Current Draw Data I) 8 to 17.5 Volts 16 to 33 Volts Candela DC FWR DC FWR Standard 15 123 128 66 71 Candela Range 15/75 142 148 77 81 30 NA NA 94 96 75 NA NA 158 153 95 NA NA 181 176 110 NA NA 202 195 115 NA NA 210 205 High 135 NA NA 228 207 Candela Range 150 NA NA 246 220 177 NA NA 281 251 185 NA NA 286 258 Tfi UL Reverberant (dBA @ loft.) 2W 1W ½W ¼W Wall-Mount SP Series 86 83 80 77 Wall-Mount SPV Series 90 87 84 81 Wall-Mount SPS Series 85 82 79 76 Wall-Mount SPSV Series 89 86 83 80 Dimensions .97---1.84" _______ 5.00 I i 5.00- 5. Wall-Mount SP Speaker Wall-Mount SPS Speaker Strobe Surface Mountin Wall-Mount Speaker Strobe with SBBSPR Surface Mount Back Ordering Information for SpectrAlert® Advance Speakers and Speaker Strobes White Red Description SPW SPR Speaker only SPWV SPRV Speaker only, High dB SPSW SPSR Speaker Strobe, Standard cd SPSW-P SPSR-P Plain Speaker Strobe, Standard cd SPSW-ALERT - Speaker Strobe, Standard cd, Amber Lens SPSW-CLR-ALERT - Speaker Strobe, Standard cd, Clear Lens SPSWH SPSRH Speaker Strobe, High cd SPSWH-P - Plain Speaker Strobe, High cd SPSWV SPSRV Speaker Strobe, Standard cd, High dB SPSWV-P SPSRV-P Plain Speaker Strobe, Standard cd, High dB White Red Description RFPW RFP 7 in x 9.5 in Retrofit Plate SBBSPW SBBSPR Surface Mount Back Box for Speakers and Speaker Strobes TRW TR Wall Mount Trim Ring Notes: All -P models have a plain housing (no "FIRE" marking on the cover) "Standard cd" refers to strobes that include 15, 15/75, 30, 75, 95, 110, and 115 candela settings, "High cd" refers to strobes that include 135, 150, 177, and 185 candela settings, SYSTEM 3825 Ohio Avenue • St. Charles, IL 60174 02015 System Sensor. for current product information, Including the latest version of this data sheet, Phone: 800-SENSOR2 • Fax: 630-377-6495 Product specifications Subject to change without notice. hint systemsensor.comn www.systemsensor.com AVOS11602 • 2/15 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7320-1653:0201 Page 1 of 1 CATEGORY: 7320 -- SPEAKERS LISTEE: System Sensor, Unincorporated Div of Honeywell Int'l Inc.3825 Ohio Ave, St. Charles, IL 60174 Contact: Trish Linhart (630) 762-5025 Fax (630) 377-7245 Email: trish.linhart@systemsensor.com DESIGN: Models SPR,SPW,SPRV, and SPNV SpectrAlert Speakers - Rectangular enclosure. Models SPCW, SPCR, SPCWV, and SPCRV SpectrAlert Speakers with round enclosure. Models SPSR, SPSRH, SPSW, SPSW-ALERT, SPSW-CLR-ALERT, *SPSWKCLRALERT SPSWH, SPSRV, and SPSWV SpectrAlert Speaker/Strobe with rectangular enclosure. Models SPSCR, SPSCRH, SPSCW, *SPSCWKCLR..ALERT SPSCWH, SPSCRV, SPSCRVH, SPSCWV, and SPSCW'JH SpectrAlert Speaker/Strobe with round enclosure. Model SPSCW-CLR-ALERT Speaker/Strobe. Model SPSW-ALERT has amber lens and is intended for non-fire use. All models identified are intended for indoor use mounted on the wall or ceiling. Models with a "K" in the suffix are suitable for indoor or outdoor use with an operating temperature rating of -40°C to +66°C (-40°F to +151°F) and have a NEMA 4X enclosure rating when used with models PWBB, PWBBW (wall) or the model PWBBCW (ceiling) plastic weatherproof back boxes or with Model MWBBW (Wall), MWBB (Wall) or MWBBCW (Ceiling) metal weatherproof back boxes. Models with a "- P' in the suffix have plain housings with no lettering on the enclosure. Models not containing "- P", in the suffix have English lettering reading "FIRE" on the housing. Refer to listee's data sheet for additional detailed product description and operational considerations. RATING: Nominal Voltage: 25 Vrms or 70 Vrms Power Settings: 1/4, '/2, 1, 2 Watts Frequency Range: 400 - 4000 Hz INSTALLATION: In accordance with listee's printed installation instructions, NFPA 72, applicable codes & ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listees name, model number, electrical rating and UL label. APPROVAL: Listed as speaker/strobes when used with separately listed compatible fire alarm control units. Suitable for wall or ceiling mount. These speaker/strobes do not generate a distinctive three-pulse temporal code pattern (for total evacuation) as required per NFPA 72, 2010 edition. If required, the appliances must be used with a fire alarm control unit that can generate the temporal pattern signal. *Corrected 02-06-12 bh This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2015 Listing Expires June 30, 2016 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division I ? S. •S(Ø) Indoor Selectable- Output Strobes and Horn Strobes for Ceiling Applications SpectrkertO Advance audible visible notification products are rich with features guaranteed to cut installation times and maximize profits. Features Plug-in design with minimal intrusion into the back box Tamper-resistant construction Automatic selection of 12- or 24-volt operation at 15 and 15/75 candela Field-selectable candela settings on ceiling units: 15, 15/75, 30, 75, 95, 110, 115, 135, 150, 177, and 185 Horn rated at 88+ dBA at 16 volts Rotary switch for horn tone and three volume selections Universal mounting plate for ceiling units Mounting plate shorting spring checks wiring continuity before device installation Electrically Compatible with legacy SpectrAlert devices Compatible with MDL sync module Listed for ceiling or wall mounting Aciencv Listinas SIGNALING @ <~> MEA LISTED APPROVED approved 7125-1653 186 (indoor strobes) 7125-1653188 (horn strobes, S4011 )chrrrres, horn strobes, horns) 3023572 M0A452-05-E chime strobes) S5512 (strobes) 7135.1653189 (horns, sir roes) SPECTRAilert Se See1sor The SpectrAlert Advance series otters the most versatile and easy-to-use line of horns, strobes, and horn strobes in the industry. With white and red plastic housings, wall and ceiling mounting options, and plain and FIRE-printed devices, SpectrAlert Advance can meet virtually any application requirement. Like the entire SpectrAlert Advance product line, ceiling-mount strobes and horn strobes include a variety of features that increase their application versatility while simplifying installation. All devices feature plug-in designs with minimal intrusion into the back box, making installations fast and foolproof while virtually eliminating costly and time-consuming ground faults. To further simplify installation and protect devices from construction damage, SpectrAlert Advance utilizes a universal mounting plate with an onboard shorting spring, so installers can test wiring continuity before the device is installed. Installers can also easily adapt devices to a suit a wide range of application requirements using field-selectable candela settings, automatic selection of 12- or 24-volt operation, and a rotary switch for horn tones with three volume selections. SpectrAlert Advance Specifications General SpectrAlert Advance strobes and horn strobes shall mount to a standard 4 x 4 x 11/2-inch back box, 4-inch octagon back box, or double- gang back box. Two-wire products shall also mount to a single-gang 2 x 4 x 17/8-inch back box. A universal mounting plate shall be used for mounting ceiling and wall products. The notification appliance circuit wiring shall terminate at the universal mounting plate. Also, SpectrAlert Advance products, when used with the Sync'Circuit'° Module accessory, shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts. When used with the Sync.Circuit Module, 12-volt-rated notification appliance circuit outputs shall operate between 9 and 17.5 volts; 24-volt-rated notification appliance circuit outputs shall operate between 17 and 33 volts. Indoor SpectrAlert Advance products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or full-wave rectified unfiltered power supply. Strobes and horn strobes shall have field-selectable candela settings including 15, 15/75, 30, 75, 95, 110, 115, 135, 150, 177, and 185. Strobe The strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1971 and shall be approved for fire protective service The strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe's entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system. Horn Strobe Combination The horn strobe shall be a System Sensor SpectrAlert Advance Model ______ listed to UL 1971 and UL 464 and shall be approved for fire protective service. The horn strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe's entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system. The horn shall have three audibility options and an option to switch between a temporal three pattern and a non-temporal (continuous) pattern. These options are set by a multiple position switch. On four-wire products, the strobe shall be powered independently of the sounder. The horn on horn strobe models shall operate on a coded or non-coded power supply. Synchronization Module The module shall be a System Sensor Sync'Circuit model MDL listed to UL 464 and shall be approved for fire protective service. The module shall synchronize SpectrAlert strobes at 1 Hz and horns at temporal three. Also, while operating the strobes, the module shall silence the horns on horn strobe models over a single pair of wires. The module shall mount to a 411/16 x 411/16 x 21/8-inch back box. The module shall also control two Style Y (class B) circuits or one Style Z (class A) circuit. The module shall synchronize multiple zones. Daisy chaining two or more synchronization modules together will synchronize all the zones they control. The module shall not operate on a coded power supply. Standard Operating Temperature 32°F to 120°F (0°C to 49°C) Humidity Range 10 to 93% non-condensing Strobe Flash Rate 1 flash per second Nominal Voltage Regulated 12 DC/FWR or regulated 24 DC/FWR1 Operating Voltage Range2 8 to 17.5 V (12 V nominal) or 16 to 33 V (24 V nominal) Input Terminal Wire Gauge 12 to 18 AWG Ceiling-Mount Dimensions (including lens) 6.8- diameter x 2.5" high (1173 mm diameter x 64 mm high) Ceiling-Mount Back Box Skirt Dimensions (BBSC-2, BBSCW-2) 7.1 "diameter x 2.2" high (180 mm diameter x 57 mm high) Ceiling-Mount Trim Ring Dimensions (sold as a 5 pack) (TRC-HS, 6.9" diameter x 0.35" high (175 mm diameter x 9 m high) TRCW-HS) Notes: Full Wave Rectified (FWR) voltage is a non-regulated, time-varying power source that is used on some power supply and panel outputs. P, 5, PC, and SC products will operate at 12 V nominal only for 15 and 15/75 cd. AVOSOO5O1 UL Current Draw Data - 1 8-17.5 Volts 16-33 Volts Candela DC FWR DC FWR Standard Candela Range 15 123 128 66 71 15/75 142 148 77 81 30 NA NA 94 96 75 NA NA 158 153 95 NA NA 181 176 110 NA NA 202 195 115 NA NA 210 205 High 135 NA NA 228 207 Candela Range 150 NA NA 246 220 177 NA NA 281 251 185 NA NA 286 258 Eamm ; 8-17.5 Volts 16-33 Volts DC Input 15 15/75 15 15/75 30 75 95 110 115 Temporal High 137 147 79 90 107 176 194 212 218 Temporal Medium 132 144 69 80 97 157 182 201 210 Temporal Low 132 143 66 77 93 154 179 198 207 Non-Temporal High 141 152 91 100 116 176 201 221 229 Non-Temporal Medium 133 145 75 85 102 163 187 207 216 Non-Temporal Low 131 144 68 79 96 156 182 201 210 FWR Input Temporal High 136 155 88 97 112 168 190 210 218 Temporal Medium 129 152 78 88 103 160 184 202 206 Temporal Low 129 151 76 86 101 160 184 194 201 Non-Temporal High 142 161 103 112 126 181 203 221 229 Non-Temporal Medium 134 155 85 95 110 166 189 208 216 Non-Temporal Low 132 154 80 90 105 161 184 202 211 16-33 Volts 16-33 Volts DC Input 135 150 177 185 FWR Input 135 150 177 185 Temporal High 245 259 290 297 Temporal High 215 231 258 265 Temporal Medium 235 253 288 297 Temporal Medium 209 224 250 258 Temporal Low 232 251 282 292 Temporal Low 207 221 248 256 Non-Temporal High 255 270 303 309 Non-Temporal High 233 248 275 281 Non-Temporal Medium 242 259 293 299 Non-Temporal Medium 219 232 262 267 Non-Temporal Low 238 254 291 295 Non-Temporal Low 214 229 256 262 Horn Strobe Tones and Sound Output Data 8-17.5 16-33 24-Volt Nominal Switch Volts Volts Reverberant Anechoic Position Sound Pattern dB DC FWR DC FWR DC FWR DC FWR 1 Temporal High 78 78 84 84 88 88 99 98 2 Temporal Medium 74 74 80 80 86 86 96 96 3 Temporal Low 71 73 76 76 83 80 94 89 4 Non-Temporal High 82 82 88 88 93 92 100 100 5 Non-Temporal Medium 78 78 85 85 90 90 98 98 6 Non-Temporal Low 75 75 81 81 88 84 96 92 7t Coded High 82 82 88 88 93 92 101 101 Coded Medium 78 78 85 85 90 90 97 98 Coded Low 75 75 81 81 88 85 96 92 tSettings 7, 8, and 9 are not available on 2-wire horn strobes. AVDSOO5O1 D7. IE Ceiling back box skirt a. Ceiling-mount horn strobes SpectrAlert Advance Dimensions SpectrAlert Advance Ordering Information Ceiling Horn Strobes PC2R* 2-Wire Horn Strobe, Standard Cd, Red PC2RH 2-Wire Horn Strobe, High cd, Red PC2W*t 2-Wire Horn Strobe. Standard cd, White PC2WH* 2-Wire Horn Strobe, High cd, White PC4R 4-Wire Horn Strobe, Standard cd, Red Ceiling Strobes SCR Strobe, Standard cd, Red SCRH Strobe, High Cd, Red SCW* Strobe, Standard cd, White SCWH Strobe, High cd, White Accessories PC4RH 4-Wire HCrn Strobe, High Cd, Red BBSC-2 Back Box Skirt, Ceiling, Red PC4W 4-Wire HCrn Strobe, Standard cd, White Back Box Skirt, Ceiling, White TRC-HS Trim Ring, Ceiling, Red TRCW- Trim Ring, Ceiling, White HS Notes: * Add "-F" to model number for plain housing (no "FIRE" marking on cover), e.g., P21 t Add "-SF" to model number for "FUEGO" marking on cover, e.g., P21 t "Standard cd" refers to strobes that include 15, 15/75, 30, 75, 95, 110, and 115 candela settings. "High cd" refers to strobes that include 135, 150, 177, and 185 candela settings, SYSTEM 3825 Ohio Avenue • St. Charles, IL 60174 Product specifications cattons subject to t2Sytens Sensor. rn change without notice. Visit sySteSenSar,00rn Z14 S—EMSORe Phone' 800-SENSOR2 • Fax' 630-377-6495 to, current product information, Including the latest version of this data sheet. AVDSOObOt • 3112 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7125-1653:0186 Page 1 of 1 CATEGORY: 7125 -- FIRE ALARM DEVICES FOR THE HEARING IMPAIRED LISTEE: System Sensor, Unincorporated Div of Honeywell Int'l Inc.3825 Ohio Ave, St. Charles, IL 60174 Contact: Trish Linhart (630) 762-5025 Fax (630) 377-7245 Email: trish.linhartsystemsensor.com DESIGN: Synchronous type strobe lights, Models SR, SRH, SW, SW-CLR-ALERT, SWH, SCR, SCRH, SCW, SCW-CLR-ALERT and SCWH followed by the suffix -P, -SP, -PG, or none. Intended for indoor use mounted on the wall or the ceiling. Refer to listee's data sheet for additional detailed product description and operational considerations. RATING: 8-17.5 or 16-33 VDC/FWR Candela: 15, 15/75, 30, 75, 95, 110, 115, *135 *150 *177 *185cd INSTALLATION: In accordance with listee's printed installation instructions, applicable codes and ordinances, and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number, electrical rating and UL label. APPROVAL: Listed as strobe lights suitable for hearing impaired application when used with separately listed compatible fire alarm control units. Suitable for indoor use, wall or ceiling mounted. Refer to listee's Installation Instruction Manual for details. *Rev. 03-11-10 fm This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2015 Listing Expires June 30, 2016 Authorized By: JAMES PARSEGIAN, Program Coordinator Fire Engineering Division It Li 0388 D Hydraulics Summary Sheet ashboard Hydiau/ks (Project Information Calculation Date: 7/18/2016 5:01:03 PM I DAYBREAK CHURCH SAUARY system ID drawing ref 2 OF 2 6515 AMBROSIA LN CARLSBAD, CA contract # rntrlr Tnfa'rmH&'n EPIC FIRE PROTECTION, INC. 765 TURTLE POINT WAY SAN MARCOS, CA 92069 calculated by ADAM BOISVERT telephone 760-310-6122 fax 760-798-0556 email EPICFIRE@COX.NET Sprinklers in Remote No. Mfgr Mod SIN# Size K 6 j VIKING I EC UPR I VK532. 111.2 building NEW construction CONCRETE/WOOD occupancy authority - Hydraulics Criteria system type WET density. IA('pL4lfe2 design std NFPA13 remote area 1500 ft2 hazard LIGHT spr coverage 20X20 ft2 sprs flowing 6 figure ca1cd volume 299.9 gal curve Flow Test static pressure 101.70 psi residual pressure 99.00 psi quantity flowing 1,000.0 GPM elevation from if 0.00 It date & time of flow test 6-30-16 location of flow test SITE 160 supply I uemann urapn 101.22 psi available at Sprinkler Demand of 95.65 psi with 140 Total System Flow of 393.7 GPM Marain: +5.5% P'-' 100 CL 40 20 0 0 75 150 225 Demand at sprinkler and interior hose flows 0 Copyright 2013 Sigma Development Group, Inc. N185 300 375 450 Water Flow (GPM) Total System Demand including Hose Flows at Zero Page 1 of 4 _e-m i Supply Analysis DAYBREAK CHURCH SANTUARY Sprinkler Flow: 293.7 GPM I Additional Flows: None Hose Flow at Zero: 100.0 GPM Total System Flow: 393.7 GPM Maximum velocity in pipe 31 -36 is 24.2 ft/sec Nodes Analysis Minimum Node Actual T Node Elev Device KFactor Flow Pressure Discharge I Notes ft ______ GPM psi GPM ___________________________________ 106 49.0 Sprinkler 11.20 40.00 12.76 40.00 105 49.0 Sprinkler 11.20 40.00 13.44 41.06 103 49.0 Sprinkler 11.20 40.00 16.00 44.80 102 49.0 Sprinkler 11.20 40.00 20.62 50.86 101 49.0 Sprinkler 11.20 40.00 26.59 57.76 100 49.0 Sprinkler 11.20 40.00 27.98 59.24 0 0.0 Hose@Zero 95.65 100.0 0 Copyright 2013 Sigma Development Group, Inc. Page 2 of 4 Q Dashb 00 Pipe Information oard Hydiaulks DAYBREAK CHURCH SANTUARY From Elevi ft Pipe ID Flows Added GPM Inside Diameter In Fittings Length ft f C Value I Friction Loss I [Total (Pt) psi Notes Fitting ft Elev (Pe) psi To ft EIev2 Type Total Total ft [FriCt (PQ psi - 104 49.00 1%" Dyna Flow 1.7280 T Len io.oj Ftg 11.3 C=120 I__-________ 0.04127 Pt 106) 12.755 Pe 0.000 Pf 0.879 106 49.00 AO 40.0 Total 21.3 Total Pressure at Node 104) 13.634 psi 104 49.00 1W' Dyna Flow 1.7280 0 Len 4.5 Ftg 0.0 C = 120 0.04331 Pt 105) 13.439 Pe 0.000 Pt 0.195 105 49.00 BN 41.1 Total 4.5 103 49.00 1%- Dyna Flow 40.0 1.7280 0 Len 15.5 Ftg 0.0 c = 120 0.15244 Pt 104) 13.634 Pe 0.000 Pt 2.363 104 49.00 BN 81.1 T otal 15.5 36 49.00 1%" Dyna Flow 44.8 1.7280 0 Len 14.5 Ftg 0.0 C = 120 0.34400 Pt 103) 15.996 Pe 0.000 Pt 4.988 103 49.00 BN 125.9 Total 14.5 Total Pressure at Node 36) 20.985 psi 36 49.00 1'/z" Dyna Flow 1.7280 0 Len 5.6 Ftg 0.0 C= 120 0.06437 Pt 102) 20.624 Pe 0.000 Pt 0.360 102 49.00 BN 50.9 Total 5.6 48.50 1'/i"Dyna Flow 125.9 1.7280 T Len 0.5 Ftg 11.3 = 120 4458 Pt7.599 Pt 36) 20.985 Pe 0.217 E36 49.00 NR 176.7 Total 11.8 Total Pressure at Node 31) 28.800 psi 100 49.00 1%" Dyna Flow 1.7280 0 Len 17.0 Ftg 0.0 c = 120 0.08143 Pt 101) 26.595 Pe 0.000 Pt 1.384 101 49.00 BN 57.8 Total 17.0 35 49.00 1'/2"Dyna Flow 59.2 1.7280 0 Len 2.5 Ftg 0.0 C = 120 0.30057 Pt100) 27.979 Pe 0.000 Pt 0.751 100 49.00 BN 117.0 Total 2.5 30 48.50 1Y2" Dyna Flow 1.7280 E Len 0.5 Ftg 5.6 C = 120 0.30057 Pt 35) 28.730 Pc 0.217 Pt 1.847 35 49.00 NR 117.0 Total 6.1 Total Pressure at Node 30) 30.794 psi 30 48.50 214- Dyna Flow 2.7030 2EE Len 18.0 Ftg 9.3 c = 120 ial 27.3f075 Pt 31) 28.801 Pc 0.000 Pt 1.993 31 48.50 FM 176.7 © Copyright 2013 Sigma Development Group, Inc. Page 3 of 4 QO (Y Dathboa,dHyd,aulics Pipe Information DAYBREAK CHURCH SANTUARY From Elevi ft Pipe ID Flows Added I Inside C Value Total (Pt) psi I Fitting ft Elev (Pe) psi Frict(P psi1 GPM I Diameter I Fittings Friction Loss Notes To Elev2 Type Total Total 22 48.50 2'/z"DynaFlow 117.0 2.7030 2EE Len 43.0 Ftg 9.3 C= 120 0.18674 Pt 30) 30.794 Pe 0.000 N 9.771 30 48.50 FM 293.7 Total 52.3 21 42.50 V/.- Dyna Flow 2.7030 2E,EE,T Len 44.0 Ftg 42.0 C = 120 0.18674 Pt 22) 40.565 Pe 2.598 N 16.053 22 48.50 FM 293.7 Total 86.0 20 42.50 21/2w Dyna Flow 2.7030 0 Len 14.0 Ftg 0.0 C = 120 0.18674 Pt 21) 59.217 Pe 0.000 Pf 2.614 21 42.50 FR 293.7 Total 14.0 13 42.50 2W Dyna Flow 2.7030 T Len 18.5 Ftg 18.7 C:: 120 0.18674 Pt 20) 61.832 Pe 0.000 N 6.937 20 42.50 FM 293.7 Total 37.2 12 31.00 r/2" Dyna Flow 2.7030 E Len 11.5 Ftg 9.3 C = 120 0.18674 Pt 13) 68.769 Pe 4.980 N 3.889 13 42.50 FR2 293.7 Total 20.8 11 31.00 3" Dyna Flow 3.3140 E Len 32.0 Ftg 10.2 C = 120 0.06921 Pt 12) 77.641 Pe 0.000 N 2.920 12 31.00 FM 293.7 Total 42.2 10 28.00 3" Dyna Flow 3.3140 E Len 3.0 Ftg 10.2 C = 120 0.06921 Pt 11) 80.561 Pe 1.299 N 0.913 11 31.00 FR 293.7 Total 13.2 1 28.00 6" Dl 5.8903 E Len 5.0 Ftg 16.1 C = 140 0.00316 Pt 10) 82.774 Pe 0.000 N 0.067 10 28.00 UN 293.7 Total 21.1 0 0.00 6" vc cuoo 58600 2EE T,EIGV, Len 160.0 Fta 77.9 C = 150 0.00285 1) 82.841 Pe 12.124 Pt 0.679 12 PSI LOSS FOR RPDA SHOWN AS ELEVATION 1 28.00 UN 293.7 Total 237.9 1 Total Pressure at Node 0) 95.644 psi 0 Copyright 2013 Sigma Development Group, Inc. Page 4 of 4 V CARLSBAD FIRE DEPARTMENT Fire Prevention Division 1635 Faraday Avenue - Carlsbad, CA 92008 760.602.4665 WATER AVAILABILITY FORM SECTION A: TO BE COMPLETED BY CUSTOMER PROJECT NAME: 6515 Ambrosia Lane SR#: (Assigned upon plan submittal) PROJECT ADDRESS: 6515 Ambrosia Lane CITY: Carlsbad PHONE: ( 760 ) 310-6155. (Epic Fire Protection, Inc.) FAX NUMBER: (760) 798-0556 Largest Building (ft.2): Sprinkled? Construction Type: SECTION B: TO BE COMPLETED BY LOCAL WATER COMPANY. CUSTOMER TO PROVIDE RESULTS TO CFD. Water Purveyor: City of Carlsbad Location of test (reference map required): southwest corner of Poinsettia and Ambrosia Lanes TEST INFORMATION IS VALID FOR 6 MONTHS FROM DATE PERFORMED Flow Test Results Static pressure: 113 PSI Hydrant Number (if applicable):H61858 Elevation of test: 287 Feet Date/Time of Test': Pitot Tube Reading:______ PSI Corresponding Flow: GPM Total Flow: 1,000 GPM Residual Pressure 110 PSI At peak demand , this water system is capable of providing a fire flow discharge of 6,475 gpm at the maximum velocity of 15 fps. At 20 psi the velocity in this area would exceed 15 fps. The maximum requested fire flow is 1,000 gpm. 'Test to be per-formed as close as possible to the time the most conservative flows and pressures are expected. Note: If the water availability information was obtained in a manner other than a flow test (i.e. computer modeling), fill out the information above as applicable and check here: I have witnessed and/or reviewed this water flow information and by personal knowledge and/or on-site observation certify that the above information is correct. Name: JenniferR.Mael,P.E. Eng. Lic. No. (if applicable): C69606 Signature:___________________________ Title/Org: PoiectManager Date: 06/30/2016 6515 Ambrosia Lane Fire Flow Request Prepared By: Jennifer R. Mae[, P.E. - MCS Date: Thursday, June 30, 2016 M,A7ERIAL DA7A SUBt*-117TAL DAYEEAK COMMUNITY CHURCH 515 AMBROSIA LN. CARLSBAD, CA EPIC FIRE PROTECTION, INC. 75 TURTLE POINT WAY SAN MARCOS, CA 92009 (760)310-0122 FAX(70)78-055 Page 1 of 4 MICROFAST® QUICK !SrjII1(jF1Gj® l II[P7W RESPONSE UPRIGHT SPRINKLER VK300 (K5.6) The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Page 2 of 4 MICROFAST® QUICK NIMM4 TECHNICAL RESPONSE UPRIGHT SPRINKLER VK300 (K5.6) The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com DESCRIPTION The Viking Microfast° Quick Response Upright Sprinkler VK300 is a small, thermosensitive, glass-bulb spray sprinkler available in several differ- ent finishes and temperature ratings to meet design requirements. The spe- cial Polyester and Eloctroless Nickel PTFE (ENT) coatings can be used In decorative applications where colors are desired. In addition, these coat- ings have been investigated for installation in corrosive atmospheres and are listed/approved as corrosion resistant as Indicated In the Approval Charts. (Note: FM global approves the ENT coating as corrosion resistant. FM Global has no approval classification Polyester coatings as corrosion resistant.) LISTINGS AND APPROVALS cULua Listed: Category VNIV FM Approved: Classes 2002 and 2020 OPERATION During fire conditions, the heat-sensitive liquid in the glass bulb expands, causing the glass to shatter, releasing the pip cap and sealing spring assembly. Water flowing through the sprinkler orifice strikes the sprinkler defector, forming a uniform spray pattern to extinguish or control the fire. INSPECTIONS, TESTS AND MAINTENANCE Refer to NFPA 25 for Inspection, Testing and Maintenance requirements. AVAILABILITY The Viking Micmfast° Quick Response Upright Sprinkler VK300 is available through a network of domestic and International distributors. See The Viking Corporation web site for the closest distributor or contact The Viking Corporation. GUARANTEE For details of warranty, refer to Viking's current list price schedule or contact Viking directly. Refer to Approval Chart 1 and Design Criteria on for cULus Listing requirements and refer to Approval Chart 2 and Design Criteria FM Approval requirements that must be followed. TECHNICAL DATA Specifications: Minimum Operating Pressure: 7 psi (0.5 bar)' Maximum Working Pressure: 175 psi (12 bar) wwp. Factory tested hydrostatically 10 500 psi (34.5 bar) Testing: U.S.A. Patent No, 4,831,870 Thread size: 1/2' NPT, 15 mm 8SF Nominal K-Factor: 5.6 U.S. (80.6 metric") Glass-bulb fluid temperature rated to -65 'F (-55 'C) Overall Length: 2-3/16" (56 mm) 'cULss Listing, FM Approval, and NFPA 13 installs require a minimum at 7 psi (11.5 bar). The minimum operating pressure for LPCB and CE Approvals ONLY 105 psi 10.35 ban. - Material Standards: Frame Casting: Brass UNS-C84400 or GM Brass Viking Technical Data may be 60usd on Deflector: Brass UNS-C23000 or Copper UNS-C19500 The Viking Corporation's Web site at Bulb: Glass, nominal 3 mm diameter http:llwww.vlklnggnnapinc.com. Belleville Spring Sealing Assembly: Nickel Alloy, coaled on both sides with The Web site may Include a more recent PTFE Tape Screw: Brass UNSC36000 edition of this Technical Data Page. Pip Cap and Insert Assembly: Copper UNS-C11000 and Stainless Sleet UNS- S30400 For Polyester Coated Sprinklers: Belleville Spring-Exposed For ENT Coated Scrinklers: Belleville Spring-Exposed, Screw and Pipcap - ENT plated Ordering Information: )Also refer to the current Viking price list.) Order Viking Microfaxta Quick Response Upright Sprinkler VK300 by first adding the appropriate suffix for the sprinkler finish and then the appropriate suffix for the temperature rating to the sprinkler base part number, Finish Suffix: Brass c A, Chrome = F, White Polyester = M-NV, Black Polyester M-1B, and ENT = ,IN Temperature Suffix ('F/'C): 135/57' = A, 155'/68' = B, 175'/79' = 0, 200'/93' cE and 286'/141' c G For example, sprinkler VK300 with a 1/2' NPT thread, Brass finish and a 155 'F/SB 'C temperature rating = Part No. 12978AB Available Finishes And Temperature Ratings: Refer to Table 1. Accessories: (Also refer to the 'Sprinkler Accessories' section of the Viking data book.) Sprinkler Wrench: Standard Wrench: Part No. 10896WlB )available since 2000) Sprinkler Cabinets: Six-head capacity: Part No. 01724A (available since 1871) Twelve-head capacity: Part No. 01725A (available since 1971) 4. INSTALLATION Refer to appropriate NFPA Installation Standards. Form No. F_052114 Rev 15.2 Bulb Color Ordinary i 155 F leg C) tOO F (38 C( Red Intermediate 175 F )79 C) too F )65 C) Yellow Intermediate 1 205 F 193 f 150 F 165 Cl Green Sprinkler Finishes: Brace, Chrome, White Polyester, Black Polyester, and ENT CorrosIon-Resistant Ceaeegs': White Polyester, Black Polyester, and Black PTFE. ENT In all temperature roxess except 135 'F (57 'C) Footnotes The sprinkler temperature rating Is stamped on the deflector. 'Based on NFPA-13. Other limits may apply, depending entire loading, sprinkler location, and other requirements eftheAuthxrily Having Jurisdiction. Refer to specific installation standards. The conneslon-resistant cxetngs have passed the standard corrosion test required by the approving agencies indicated In the Approval Charts. Those tests cannot and do not represent all possible corrosive environments. Prior to installation, verily through the end-user that the coatings are compat-ible with or callable for the proposed environment. For automatic sprinklers, the coatings indicated are applied to the exposed exterior surfaces only. Nxla that the spring is exposed on sprinklers with Polyester, ENT, and PTFE coatings. For ENT coaled automatic sprinklers, the waterway is coated. Figure 1: Standard Sprinkler Wrench 1e69eWlB Form No. F_052114 Rev 15.2 Page 3 of 4 MICROFASPQUICK "J II(JNI6i iirsq.'ny RESPONSE UPRIGHT SPRINKLER VK300 (K5,6) The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcsvikingcorp.com Approval Chart I (UL) It Response Mk.fccfaotB Quick Upright Sprinkler VK300 A X+ rteqav,vei Maximum 175 PSI (12 bar) WWP Base Part SIN Thread Size Nominal K-Factor I Overall Length I Listings and Approvals' Number NPTBSP I U.S. I metric' Inches mm cULus Vag LPCB NYC' CE 12978 VK300 1/2' 15mm 5.6 80.8 Product Below Limited 2-3/16 J'I9t7tlt.7l7 56 j Al, B2 -- - See footnote 7. - rNOTICE 066618 1 VK300 1/2' 15mm 5.6 80.6 2-3/16 56 Office) z(.fm,cmteLocal Viking I Al, B2 - - bee footnote 7.1 - Approved Temperature Ratings Approved Finishes A - 135 'F(57'C), 155 'F )68 'C), 175 'F (79 'C), 200 'F (93 'C), and 1 - Brass, Chrome, White Polyester", and Black Polyester" 2- ENT 9-155 'F (68 'C), 175 'F )79 'C), 200 'F (93 'C), and 286 'F (141'C) Footnotes Boon port number, shoorr. For complete part number, refer to Viking', current price schedule. 'Metric K.tacta, nrwaourerrent Shown a when pressure Is measured in Bar. When pressure is measured in kPa, dod. the metric Masse shown by 10.0. Thistable ,hewo the listings and approvals available at the fine of printing. Check with the manufacture, for any additional approval,. 'Listed by Underwriters Laboratories Inc. for us In the U.S. and Canada 'Other colors em mailable on request with the San,, Listings and Approvals as the standard colors. 'cULus Usted as sanoelon resistant. Moor, New York City requirements, effective July 1, 2008 'Accepted for use, City 010,0 York Board of Standard, and Appeals, Calendar Number 219-76-SA and City of Now York Department of Buildings, MEA 89-02-E, Vol. 15. DESIGN CRITERIA -UL (d/so refer to Approval Chart 1 above.) cULus Ltstlna Reeuiremuets: The Viking Micmtaot' Quick Response Upright Sprinkler V6300 Is cULus Listed as indicated in Approval Chart ff0, Installation in accordance with the latest edition at NFPA 13 for standard spray sprinklers. - Designed for use In Light and Ordinary hazard occupancies. - The sprinkler installation rules contained in NFPA 13 for standard spray upright sprinklers must be followed. IMPORTANT: Always refer to Bulletin Form No. F_091699 - Care and Handling of Sprinklers. Also refer to page QRI-3 for general care, Installation, and maintenance Information. Viking sprinklers are to be Installed In ac- cordance with the latest edition of Viking technical data, the appropriate standards of NFPA, FM Global, LPCB, APSAD, VdS or other similar organizations, and also with the provisions of governmental codes, ordinances, and standards, whenever applicable. Page 4 of 4 The Viking Corporation, 210 N industrial Park Drive, Hastings MI 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@viklngcorp.com Approval Chart 2 (PM) Utcroiaet' Quick Response Upright Sprinkler VK300 Maoimitm 178 PSI 11? her) WWP Base Part I ) Thread Size I Nominal K-Factor FM Approvals' SIN Number' I I NPT I BSP U S metric also to Design Criteria below.) inches Overall Le L 12978 VK300 I 1/2' I 15 mm 5.6 80.6 ' 2-3/16 Al, B2 NOTICE 06661B 9000 1/2' - Product Below - LimitedAvailability I 15mm 6 I 80.6 (Contact Local I 2-3/16 56 Al, B2 Approved Temperature Ratings Approved Finishes A-135 'F (57 'C), 155'F (68 'C), 175 'F (79 'C), 200 'F (93 'C), and 286 'F )141'C) - Brags, Chrome, White Polyesters, and Black 8-155 'F (68 'C), 175 'F (79 'C), 200 'F (93 'C), and 285 'F )141'C) Polyester' 2- ENT Footnotes 'Base part number in shown. For complete pad number, refer to Viking's currant price schedule. 'Metric K-factor measurement shown Is when pmssure is measured 'a d in Bar. When pressure measured 'Thio table shows the FM Approvals available at the time of printing. Check with the manufacturer for any additional approvals. in kPa, divide the mehic K-factor shown by 10.0. 'Other colors are available on request with the same Approvals as the standard colors. FM approved as corrosion resistent. ENEIIERI&EM (ft/so refer to Approval Chart 2 abuvn.l The Mic,ofast° Quick Renpanse Upnight Sprinkler VK300 is FM Approved as a quick response Nee.Storage upright sprinkler as indicated in the FM Approval Guide. For specific application and installation requirements, reference the latest applicable FM Loss Prevention Data Sheets (including Data Sheet 2-0). FM Global Loss Prevention Data Sheets contain guidelines relating to, but 001 limited to: minimum water supply requirements, hydraulic design, coiling slope and obstructions, minimum and maaimvm allowable spacing, and defector distance below the ceiling. NOTE: The FM Installation guidelines may differ from cULus netter NFPA criteria, IMPORTANT: Always refer to Bulletin Form No. F_091699 -Care and Handling of Sprinklers. Also refer to page QRI-3 for general care, installation, and maintenance information. Viking sprinklers are to be installed in ac cordance with the latest edition of Viking technical data, the appropriate standards of NFPA, FM Global, LPCB, APSAD, VdS or other similar organizations, and also with the provisions of governmental codes, ordinances, and standards, whenever applicable. Form No. F_052114 Rev 15.2 Form No. F_052114 Rev 15.2 Page 1 o 6 _______________________ STANDARD/QUICK RESPONSE SsJ 11(1 rc* ~111h7M UPRIGHT SPRINKLER EXTENDED COVERAGE VK5321K11.2 ------------ The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com 1. DESCRIPTION Viking EC/OREC Uptight Sprinkler VK532 is a thermosensitive spray sprinkler available in several different finishes and temperature ratings to meet varying design requirements. The extra-large orifice produces the flows requited to meet Light and Ordinary Hazard density re- quirements at lower pressures than standard orifice or large orifice sprinklers. The glass bulb operating element and special deflector characteristics meet the challenges of quick response extended coverage standards. Upright Sprinkler VK532 is cULus Listed as standard and quick response and FM Approved as quick response. The special Polyester and Electroless Nickel FIFE (ENT) coatings can be used in decorative applications where colors are desired. In addition, ENT coating has been investigated for installation in corrosive atmospheres. See Approval Charts. 2. LISTINGS AND APPROVALS cULus Listed: Category VNIV <> FM Approved: Class 2022 Refer to Approval Chart 1 and Design Criteria for cULus Listing requirements, and refer to Approval Chart 2 and Design Criteria for FM Approval requirements that must be followed. 3. TECHNICAL DATA Specifications: Minimum Operating Pressure: Refer to the Approval Charts. Maximum Working Pressure: 17$ psi (12 Bar). Factory tasted hydrostatically to 500 psi (34.5 bar). Factory tested hydrostatically to 500 psi (34.5 bar). Thread size: 314 (20 mm) NPT Nominal K-Factor: 11.2 U.S. (161.3 metrict) t Metric K-factor measurement shown Is in Bar. When pressure is measured in kPa, divide the metric K-factor shown by 10.0. Glass-bulb fluid temperature rated to -65 'F (-55 'C) Overall Length: 2-5116 (59 mm) Material Standards: Sprinkler Frame: Brass UNS-C84400 Defector: Copper UNS-C19500 Viking Technical Data maybe found on Bulb: Glass, nominal 3 mm diameter The Viking Corporation's Web site at Belleville Spring Sealing Assembly: Nickel Alloy, coated on both sides http:/Mww.othinggrouptnc.cem. with Teflon Taps The Web site may include a mere recent Screw: Brass UNS-C36000 edition f this Technical Data P Pip Cap and Insert Assembly: Copper UNS-C11000 and Stainless Steel age. UNS-S30400 For Polvester Coated Sprinklers: Belleville Spring-Exposed For ENT Coated Snrinkler: Belleville Spring-Exposed, Screw and Pipcap-ENT plated. Ordering Information: (Also refer to the current Viking price list.) Order Viking EC/OREC Upright Sprinkler VK532 by first adding the appropriate suffix for the sprinkler finish and then the appro- priate suffix for the temperature rating to the sprinkler base part number. Finish Suffix: Brass = A, Chrome = F, White Polyester = M-/W, Black Polyester = M-/B, and ENT = JN Temperature Suffix: 135 'F (57 'C) = A, 155 'F (68 'C) = B, 175 'F (79 'C) = D, 200 'F (93 'C) = E, and 286 'F (141 'C) eG For example, sprinkler VK532 with a Brass finish and a 155 'F (68 'C) temperature rating c Part No. 08687AB Available Finishes And Temperature Ratings: Refer to Table 1. Accessories: (Also refer to the "Sprinkler Accessories" section of the Viking data book.) Sprinkler Wrenches: Standard Wrench: Part No. 05118CW/B (available since 198 1) Wrench for recessed pendant sprinkler: Part No. 11663W/B" (available since 2001) "A W ratchet is required (not available from Viking). Page 2 of 6 'JIKINGI® The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 48058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: tochsvcsvlkingcorp.com Sprinkler Cabinets: Six-head capacity: Part No. 01724A (available since 1971) Twelve-head capacity: Part No. 01725A (available since 1971) 4. INSTALLATiON Refer to appropriate NFPA Installation Standards. S. OPERATION During fire conditions, the heat-sensitive liquid in the glass bulb expands, causing the glass to shatter, releasing the pip cap and sealing spring assembly. Water flowing through the sprinkler orifice strikes the sprinkler deflector, forming a uniform spray pattern to extinguish or control the fire. INSPECTIONS, TESTS AND MAINTENANCE Refer to NFPA 25 for Inspection, Testing and Maintenance requirements. AVAILABILITY Viking Sprinkler VK532 is available through a network of domestic and international distributors. See The Viking Corporation web site for the closest distributor or contact The Viking Corporation. GUARANTEE For details of warranty, refer to Viking's current list price schedule or contact Viking directly. Protective Sprinkler Clip Wrench Flat 41 05118 Figure 1: Standard Sprinkler Wrench OSIIBCWIB STANDARD/QUICK RESPONSE EXTENDED COVERAGE UPRIGHT SPRINKLER VK532 (K11.2) Form No. F_053114 Rev 14.1 (New page for VK532) Form No. F_053114 Rev 14.1 Page 3 of 6 ® STANDARD/QUICK RESPONSE EXTENDED COVERAGE NIKJNG* UPRIGHT SPRINKLER VK532 (KII.2) The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcsvikingcorpcom Vu:l,I Sprinkler Temperature VAILABLE SPRINKLERlB6IrJ9 Sprinkler Nominal 8Iuu1:eclltd[s1afrig0l.Ial0l9a1tla,- Maxlmum.Ambierlt Bulb Color U Clasttifit'.atinn Tnmpemtrire Rating' Coiling Temperatitra' Ordinary 135 'F (57 'C) 100 'F (38 'C) Orange Ordinary 155 'I- (58 'C) 11)0 '1- (38 'C) Red Intermediate 175 IF (76 'C) 150 'F (65 '0) Yellow Intermediate 200 'F (93 'C) 150 'F (65 'C) Green High 286F (141 'C) - - 225 'F (107 'C) Blue Sprinkler Finish; Orsiss, Chrome White Polyester' Black Pqlyesler', and ENT Corrosion-Resistant Coatings': ENT Footnotes The sprinkler )ernpneotrrre rating In etorrrped on th,r 'lafisinlor 'Based on NFPA-13. Other limits may apply, depending on Ore loading, sprinkler location, and other requirements of the Authority lacing Jurisdiction. Refer to specific installation standards. 'For automatic sprinklers, the coatings indicated are applied to the exposed exterior surfaces only. Note that the spring is exposed on sprinklers with Polyester. 'The xurrxnioo-rosixtunt cualliigs have puocud the standard corrunlon Lest ruquirod by the approving agencies Indicated hi die Approval Olnaro. These tests cannot and do not represent all possible corrosive environments. Prior to installation, verify through the end-user that the coatings are compat- ible with or suitable for the proposed environment. For ENT sprinklers, all exposed surfaces and the waterway are coated, but note that the spring is exposed. - Page 4o16 STANDARD/QUICK RESPONSE EXTENDED COVERAGE 't,flI(J1JJ l:IlE.rU'7M UPRIGHT SPRINKLER VK532 (KII.2) The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcsvikingcorp.com Approval Chart I (UL) -cm KEY ASm-Emxellmn5,sss SRIQR EC Upright Sprinkler VK532 Sprinkler ease "[ spy Thread Sian j Nominai 6-Pester Masimum Water Length sic Part Number' inches mm 0.5. j Working Pressure none overall s mm 00487 Upright VK532 314 20 rr.2 ror.3 175 psi 112 Sari 2-5t16 05 Minimum Water Supply Requirement.' Lisenas nod Approweis' Max. Sprinkler Maximum (Refer also to UL Design spacing Arm par i!o Stenderd Response 16 It. crOft 14.0 250n'123.8 38gpnr @ 11.5 psi 51 gpnn20.7 psi Cl,02 n.4.9 m) ml) It 43.0 linnin C.79 earl (1 93.1 Urnin B 1.43 Ourl tart ott it (5.5 324 Ii' 130.1 - 40 Spin ro.r psi 65 gym 0533.7 psi Cl 02 000.5 nI rnr') (185.6 Lirnin 051.32 Bar) 246.1 Llrnin 052.32 earl 20 ft. 02010(0.1 4051P137.2 - 60gprnB2a.7psi oogpmByr.Opsi C2 nrc 0,1 xl ml)1227.r Lirnin 051.00 earl 302.0 1mm 053.52 earl Qatok Response 1210n121013.7 14411' - 3OgpirrBi.2pal 300pnr0512r p 01 02 003.701 113.4cr') (r13.0 limin @50 earl 1147.7 01mm 05.04 earl 14105141014.3 10011' 30 0pm057.2 pen 3ogprn B 12,1 psi 02 in 4.31111 lle.2111'l irla.o irvin @.50 earl 1147.7 lirnhrr 05.04 Bail 150,0 101014.0 250 5'123.a 30gpm057.2y5i Br E2 inn 4.001 int'l (113.6 Llnrin 05.00 Be,) - - 18ft.O 010(5,5 3241t'(30.1 33gpmnBA.7 psi 1r24.OLI sr E2 no 5.5n1) xi') nm 05.00 Bar) - - 20 ft. 02010 (5.1 40011' 137.2 45 gpnr B t2.O psi 1151.4 Al,F2 mx 0.1 ci) ci') Llrnin 05 Be Oar) - - Approved Temperature Raesae A - t35 'F 157 'C) and 175T (79'C) 9-135 F(57C). 155 (68'C), and 175 *F (79 'C) Appmved Finishes C -155 F (00 C), 170 F )70 'C), 200 'F 03 'C), and 236 T (141 C) I - Brass, Chrome, Writs sxlysstnn, and 91,0k Polyester 0-r55'ploe.C) 2-ENT' - 155:F lOe 'Cl, and 175 'F 70 Cl F - riO F (70 'C) Footnotes Part number shown S the bass part nombnr. For complete part number, rotor to current Viking price fOr schedule. 'MeSic K-toornr measurement shownis when pressure is nroaew,ed In Bar. Wren prsetwrn is rnsoswrod in kPa, dM46 the rnebic K-luster shout by tOO. This short shown listings and approvals available at nero 01 printing. Check with the nnanul000nror for any additional approvals. 'cULwx Listed for use in the U.S. and Canada. To determine 'Minimum Vdaten Supply Roquirennont' for areas of 000erugo where length and width of acisal sprinkler spacing are not equal, select One 'Manirnxnn Sprinkler upswing' from the chart that is equal to or grouron than the larger of the 000wai spacing (length or width) dimensions used. Example When using 10-6' ii 13-0' sprinkler spacing, provide the 'Minimum lOSmor Supply Requirement' listed In the chart for 14-57014-0' spacing. For arousal coverage smaller than shown, 440 fire 'Miniirriunm VAlor fiuppry Requirenreni' in Ore apylupriaro flazuru group ion Ore minor ieiem else liou. The distance torn spriukinin Li nulls shall si exceed one-honors 'Maoinnurn Sprinkler Spacing' listed for th,'Minimum VAlor Supply Requironront' used. oULos Listed as sarnoolon-nasistunt. Form No. F_053114 Rev 14.1 Form No. F_053114 Rev 14.1 Page 5 of 6 STANDARD/QUICK RESPONSE EXTENDED COVERAGE rJII1(IF*m1J® UPRIGHT SPRINKLER VK532 (KII.2) The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com DESIGN CRITERIA - UL _yyrefer tayyChart 1.) cULos Usthra Reosatremeeto: EC-ELO Upright Sprinkler VK532 is cULus Usted as indicated in Approval Chart I for installation in accordance with the latest edition of NFPA 13 for extended coverage upright sprinklers as Indicated below: The minimum water supplies and maximum areas of coverage shown in Approval Chart 1 are designed to provide the following design densities: 010 gprrn/ft' (4.1 mm/min) for Light Hazard densities; 0.15 gprn/ft' (6.1 mm/mix) for Ordinary-Hazard Group I densities; 0.2 gprrn/ft' (8.1 mm/wIn) for Ordinary-Hazard Group II densities. The sprinkler installation rules contained in NFPA 13 for extended coverage upright and pendent spray sprinklers must he followed. Viking EC-ELO Upright Sprinklem are cULos Listed for use in unobstructed construction, and noncombustible obstructed construction consisting of Solid steel and/or concrete beams as defined in the latest edition of NFPA 13. - Ceiling slope not to exceed 2/12 (9.00). lisa. Vtldee ECOH.ELO UorlelrO Sortekier VXt32 is specificalte cULus Listed far Ordinorn Hazard Ooornpesctes: For non-combustible obstructed construction within bosses or bar joists honing non-combustible web members greater than 1 (25.4 mm) when applying the 4 times obstruction criteria rule as defined in NFPA 13 under 'Obstructions to Sprinkler Discharge Pattern Development'. - For Installation under concrete tees when installed as follows: The stems of the concrete tee construction mast be spaced between 30(0.9 m) and 70-6 in (2.3 m) on cooler. The depth of the cancrele tees must not exceed 30 in (762 mm). The maximum permitted concrete tee length Is 320(9.0 m). However, where the concrete lee length eocae,/s 320(8.8 m), non-combustible baffles, equal In height to the depth of the tees, can be installed so that the space between the tees dons not exceed 325(8.8 m). The sprinkler detfectur Is to be located in a horizontal plane at or above 1' (25.4 mm) below the bottom of the concrete tee sterns. When the sprinkler deflector Is located higher than a horizontal plane l')25.4 mm) beneath the bottom of the concrete tee stems, the obstruc- tion to sprinkler discharge criteria requirements of NFPA 13 for extended coverage upright sprinklers applies. IMPORTANfl Always refer to Bulletin Form No. F_091699 - Care and Handling of Sprinklers. Also refer to pages ECI-3 for general care, installation, and maintenance Information. Viking sprinklers are to be installed in accor- dance with the latest edition of Viking technical data, the appropriate standards of NFPA, LPCB, APSAD, VdS or other similar organizations, and also with the provisions of governmental codes, ordinances, and standards, whenever applicable. Page 6 of 6 STANDARD/QUICK RESPONSE EXTENDED COVERAGE "IJ UPRIGHT SPRINKLER NG VK532 (KII,2) The Viking Corporation, 210 N Industrial Park Drive, Hastings Ml 49056 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcsvikingcorp.com Approval Chart 2 (FM) r,,rn,aao, pOsy Quick ResponseEats died d.d Coverage P.l.O Upright Sprinkler VK532 For HC-1, HC-2, and HC-3 Occupancies AltO. Lccrdreor llrnrAeeitel Mpohn,Urer 175 PSI (12 Bar) WWP Maximum Sprinkler Maximum Area Reform Doalen Criteria below, FMAppranaF Spacing (LoW') per Sprinkler NOTE' FM Installation guidelines may differ from cULus end/or NFPA criteria. Refer to the latest applicable FM Loss Prevention Data Sheets (Including 2-0 and 3-20), Upright Sprinkler VK632 160.0160. (4.9 m 4.9w) 256 II' (23.8 ml Al 1811. c 1811. (5.5 on 5,5 m) 3241'c' (30.1 re°) Al 205.0 200. (6.1 ma 6.1 m) 400 ft' (37.2 m') Al ------------ Appreved Temperature Ratings Approved Finishes A- 155 'F (68 'C), 175'P (79 'C), 200 'F (93 'C). and 286 'F (141 'C) I - Brass, Chrome, White Polyester, Black Polyester, ENT' Footnotes This short shave the FM Approvals available otters or printing. Check with One ,nseuravturer for any additionalappr505ls. 'To dararrvine 'Minimum tsbrar Supply Reqoiremont' Is, areas of coverage where length and wider or actual sprinkler spacing are not equal, select Ore 'Marinrurn Sprinkler tipzcing' from the chart that is equal rc nr greater than the larger ofthe Mal spacing broth nru,IdthIdimensions used. Soornyle:ltifren using 10.60130' sprinklerupaclng, provide the 'MinimA,, ware, Supply Requirement' listed in the chart for 14.0's 14.0' epoolng. For areas of oxuer000 sw.iar than shown, 000 the 'Minimum lhlsrer Supply Requirnnrenr' in One epprupriata hazard group for the root loge, area tiered. The dIstance from sp/nears to walls shall not exceed oee.l'af the 'Maximum Op/near Spaorrg tisled Ion the 'Minimum ASIa, Supply veqrurerrrent' used. FM Approved as wnnslon-resjstant FM Aooreeai Reaslmeeeeots, Sprinkler VK532 is FM Approved as a quick response Non-Storage extended coverage upright sprinkler as indicated in the FM Approval Guide tar use in occupancy hazard classifications HC-1, HC-2, and HC-3. For specific application and Installation requirements, reference the latest applicable FM Loss Prevention Data Sheets (including Data Sheets 2-0 and 3-26). FM Global Loss Prevention Data Sheets contain guidelines relating to, but not limited to: minimum water supply requirements, hydraulic design, ceiling slope and obstructions, minimum and maximum allowable spacing, and deflector distance below the ceiling. NOTE, The FM installation guidelines may differ from cULso and/or NFPA criteria. IMPORTANT: Always refer to Bulletin Form No. F_091699 - Care and Handling of Sprinklers. Also refer to page ECI-3 for general care, Installation, and maintenance information. Viking sprinklers are to be Installed in ac- cordance with the latest edition of Viking technical data, the appropriate standards of NFPA, FM Global, LPCB, APSAD, VdS or other similar organizations, and also with the provisions of governmental codes, ordinances, and standards, whenever applicable. Form No. F_053114 Rev 14.1 Form No. F_053114 Rev 14.1 (New page for VK532) 13) FIRE SPRINKLER CORPORATION QUICK RESPONSE A UTOMA TIC SPRINKLERS GL SERIES UPRIGHT. PENDENT VERTICAL SIDEWALL HORIZONTAL SIDEWALL QUICK RESPONSE AUTOMATIC SPRINKLERS GL SERIES UPRIGHT. PENDENT. VERTICAL SIDEWALL HORIZONTAL SIDEWALL. CONVENTIONAL (OLD STYLE) SPECIFICATiONS CONVENTIONAL (OLD STYLE) DESCRIPTION AND OPERATION The Globe Quick Response GL Series Sprinklers are a low profile yet durable design Which utilizes a 3mm frangible glass ampule as the thermosensitive element This provides sprinkler operation approximately six times faster than ordinary sprinklers. While the Quick Response Sprinkler provides an aesthetically pleasing appearance, it can be installed wherever standard spray sprinklers are specified when allowed by the applicable standards. It offers the additional feature of greatly increased safety to life and is available in various styles, orifices, temperature ratings and finishes to meet many varying design requirements. Quick QUICK RESPONSE Response Sprinklers should be used advisedly and under the UPRIGHT CONVENTIONAL direction of approving authorities having jurisdiction. The heart of Globes GL Series sprinkler proven actuating assembly is a hermetically sealed frangible glass ampule that contains a precisely measured amount of fluid. When heat is absorbed, the liquid within the bulb expands increasing the internal pressure. At the prescribed temperature the internal pressure within the ampule exceeds the strength of the glass causing the glass to shatter. This results in water discharge which is distributed in an approved pattern depending upon the deflector style used. QUICK RESPONSE TECHNICAL DATA PENDENT VERTICAL See reverse side for Approvals and Specifications. SIDEWALL .Temperature Ratings - 135°F (57°C), 155°F (68°C), 175°F (79°C), 200°F (93°C), 286°F (141°C) Water Working Pressure Rating -175 psi (12 Bars) lob @a Factory tested hydrostatically to 500 psi (34 Bars) Maximum low temperature glass bulb rating is -67°F (-55°C) QUICK RESPONSE Frame - bronze • Deflector - brass • Screw - brass HORIZONTAL LPC/CE Lodgement Wire - stainless steel • SIDEWALL HORIZONTAL Bulb seat - copper Spring -nickel alloy • Seal - teflon SIDEWALL Bulb - glass with alcohol based solution, 3mm size SPRINKLER TEMPERATURE RATiNG/CLASSIFICATION and COLOR CODING CLASSIFICATION I AVAILABLE SPRINKLER I BULB COLOR I N.F.P.A. MAXIMUM I I TEMPERATURES I I CEILING TEMPERATURE ORDINARY - 135°F1155°F °C/68°C I ORANGE/RED 100°F 38°C - INTERMEDIATE I 175°F/200°F 79°C/93°C I YELLOW/GREEN I 150°F 66°C I HIGH 1 286°F 141°C 1 BLUE 1 225°F 1O7°CJ 4077A1RPAR5( DRIVE, STANDISH, MICHIGAN 46658 989-846-4583 • FAX989-846-9231 JULY 2012 A-20 BULLETIN GL5615, REV. #9 NOMINAL "K° FACTOR THREAD SIZE [ LENQTW I FINISHES 2.8 (39 metric) 112 NPT 2 1/4 (5.7cm) Factory Bronze 4.2 (59 metric) 1/2' NPT 2 1/4 (5.7cm) Chrome 5.6 (80 metric) 112 NPT 2 1/4 (5.7cm) White Polyester 7.8 (111 metric) 1/2 NPT 2 1/4" (5.7cm) - Block Polyester" 8.1 (116 metric) 3/4" NPT 27/16" (6.2cm) METRIC CONVERSIONS ARE APPRO)SMA1E. HORIZONTAL SIDEWALL 62 9/16. FINISHES AVAILABLE ON SPECIAL ORDER. AVAILABLE AS s5l.u, LISTED CORROSION RESISTANT WHEN SPECIFIED ON ORDER. APPROVALS STYLE SIN K HAZARD' 1301F lOW' I7IZF 2INTF 25601 CULlS FM PC CE DO NYC_ S MEA MODEL FACTOR S8C 56C 701C 83C 141-C 012815 ZR UI X S S S X X - - - S 0L4215 4.2 UI S It S X S X - - - X UPRIGHT 0L5805 5.6 11-1108 X X S X X S X S S S 018115 7.01 LI-lION It X X It X S - - - S 018118 El 114108 5 5 X S X S It S X S 5(2051 2.8 LII S X X 2 X It - - - S 0L4201 4.2 UI X It X S S S - - - X PENDENT GLSRD1 5.6 LIOH X It S It X S S X It X 518151 7.81 11-/108 5 X S X It S X - - It 018106 8.1 11/108 X X 5 5 It x S X S X VERTICAL 01.5632 5.6 LII X X - - It X - X x i - SIDEWAlL1 018133 81 111 X It S - X It S - - - - 2.0 LII S S It X S X - - - It HORIZONTAL 4.2 18 5 5 X S S - - - S DIDEWAIL 5.6 LI-I/OH It S X S X S - - S JGL8127 S. 11-508 X X X It -. -. X X - 0.1 /11011 - - S X X S X - - - - CONVENTIONAL 58 1141011 X X X - X - - S 81 18/08 - - X XlOISSTYLEI X X X - .- ISPRINKLERS SHALL BE LIMITED AS PER THE REQUIREMENTS OF NFPAI3 AND ANY OTHER RELATED DOCUMENTS. SHORIZONTAL SIDEWALL sULm LISTED FOR DEFLECTOR 4 TO 151 BELOW THE CEIUNG. FM APPROVED 4 TO 6 BELOW THE CEILING. INSTALL IN ACCORDANCE TO ED5306 AND ANY OTHER RELATED DOCUMENTS. 'PENDENT VERTICAL SIDEWALL cULls LISTED FOR 6' BIN. SPACING. tUPRIGIlT VERTICAL SIDEWALL sULs. LISTED FOR 9 BIN. SPACING. OH ORDINARY HAZARD LI-I 11018 HAZARD 1)? NPT ORDERING INFORMATiON GLOBES PRODUCT WARRANTY SPECIFY ouanlity Model Number - Style Globe agrees to repairor replace any of its OWS manufactured Orifice Thread Sizes Temperature products found lobe defective in material or workmanship for a Finishes desired period of one year from date of shipment. -Quardity - Wrenches - P/N 325390 (1/2; For spectflc details of our warranty please refer to Price List P/N 312366 (L.O.) Terms and Conditions of Sale (Our Price Ust). G90 FRI 4077 AIRPARK DRIVE, STANDISH, MICHIGAN 48658 989-846-4553 FAX 989-846-9231 FIRE SPRINKLER CORPORATION 1-800-248-0278 www.globeSprInkIer.com JUNE 2012 PRINTED U.S.A. BULLETINGL561S, REV. #9 GW.60E FIRE SPRINKLER CORPORATION QUICK RESPONSE EXTENDED COVERAGE LIGHT HAZARD AUTOMATIC SPRINKLERS MODEL GL8109 PENDENT QUICK RESPONSE EXTENDED COVERAGE LIGHT HAZARD AUTOMATIC SPRINKLERS MODEL GL8109 PENDENT cP1r'I1I('iJT1nM DESCRIPTION AND OPERATION The Globe Quick Response Model GL8109 Extended Coverage Pendent Sprinkler for Light Hazard occupan Alt - cies is a low profile yet durable design which utilizes a 3mm - frangible glass ampule as the thermosensitive element. This provides sprinkler operation approximately six times faster thanthan ordinary sprinklers. While this Quick Response -- -. - Sprinkler provides an aesthetically pleasing appearance, it can be installed wherever standard light hazard ex- tended coverage pendent sprinklers are specified; but " offers the additional feature of greatly increased safety to life. Quick Response Sprinklers should be used advisedly and under the direction of approving authorities having - - - jurisdiction, in accordance with their listings and in accor- QUICK RESPONSE dance with NFPA 13. EXTENDED COVERAGE The heart of Globe's GL Series sprinkler proven PENDENT actuating assembly is a hermetically sealed frangible glass ampule that contains a precisely measured amount of fluid. When heat is absorbed, the liquid within the bulb expands increasing the internal pressure. At the pre- scribed temperature the internal pressure within the am- pule exceeds the strength of the glass causing the glass to shatter. This results in water discharge which is distributed ( in an approved pattern. TECHNICAL DATA See reverse side for Approvals and Specifications. -Temperature Rating - 135°F (57°C), 155°F (68°C), 175°F (79°C) . and 200°F (93°C). .Water Working Pressure Rating - 175 psi (12 Bars). "°..- Factory tested hydrostatically to 500 psi (34 Bars). QUICK RESPONSE *Maximum low temperature glass bulb rating is -67°F (-55°C). RECESSED -Frame -bronze • Deflector - brass • Screw - brass . EXTENDED COVERAGE Bulb seat - copper • Spring - nickel alloy • Seal - teflon PENDENT Bulb - glass with alcohol based solution, 3mm size. Escutcheon Assembly - steel SPRINKLER TEMPERATURE-RATING/CLASSIFICATION and COLOR CODING LAS IFICATION AVAILABLE BULB N.F.P.A. MAXIMUM CEILING C SPRINKLER TEMPERATURES COLOR TEMPERATURE ORDINARY 135F1155F .57'Cf68C ORANGE/RED 100°F 39°C INTERMEDIATE 175'F/200'F 79 C/US C YELLOWIGREEN 150'F 66 C 4077AIRPARK DRIVE, STANDISH, MICHIGAN 48658 989446-4583 • FAX989-846-9231 JULY2005 A-41 BULLETIN GLS1O9, REV. #5 I NOMINAL "K' FACTOR THREAD SIZEF LENGTH I FINISHES Factory Bronze ISatin Chrome' 8.1 (116metric) 4" N FIT 3(7.6 ) Bright Chrome I White R3IyeMerB I PJm* ,Iveer' Lead Coated' NOTE METRIC CONVERSIONS ARE APPROXIMATE. 'FINISHES AVAILABLE ON SPECIAL ORDER. 'AVAILABLE AS cUL,i LISTED CORROSION RESISTANT WHEN SPECIFIES ON ORDER. APPROVALS STYLE SIN K 135°F 155°F 175°F 200°F MODEL FACTOR 57°C 68°C 79°C 93°C cULus PENDENT GL8109 8.1 X X X X X U.L. LISTING DESIGN -USE REQUIREMENTS FOR LIGHT HAZARDS ONLY SIN AREA OF MIN. PRESSURE MODEL STYLE TEMP. COVERAGE P.S.I. FLOW IN GP.M. 135°F157°C 16' x 16' 10.3 26 Standard 155°F/68°C GL8109 & 175°F/79°C 18's 18' 16.6 33 Recessed 2006F/93°C 135'F/57°C 20' 0 20' 24.4 40 NOTE DUE TO THE HIGH SPRAY PATTERN CREATED BY THIS SPRINKLER, THERE MUST BE A MINIMUM SPACING OF 8-0' BETWEEN SPRINKLERS TO ELIMINATE THE RISK OF COLD SOLDERING. ORDERING INFORMATION ,wr ,?0tá SPECIFY 2 DIA, Quantity - Model Number Style RIJAINER ii KBUCER . Orifice Temperature Finishes desired Quantity - Wrenches - P/N 312366 I CAV Quantity - Recessed Wrenches - P/N 325401, Rev. 0 Quantity - Protective Caps - P/N 327109-CAP (Friction Fit Recessed) 7/8- MAX. I GLOBED PRODUCT WARRANTY Globe agrees In repair or replace any of its own manufactured products found to be defective in material or workmanship for a period of one year from date of shipment. CROSS SECTION For specific details of our warranty, please refer to Price List Terms and Conditions of Sale (Our Price List). 4077AIRPARK DRIVE, STANDISH, MICHIGAN 48658 %V116m: 989-846-4583 EAX989-846-9231 FIRE SPRINKLER CORPORATION 1-800-248-0278 www.globesprinkler.com JULY2005 PRINTEOU.SA BULLETIN GL8109, REV #5 The Cost Effective Replacement for Schedule 10 Realizing the growing need of fire protection systems in commercial and residential construction, Bull Moose Tube has added Eddy Flow to its comprehensive line of sprinkler pipe products. Eddy Flow is a specially engineered replacement for schedule 10, offering better flow characteristics while providing design flexibility. This product is FM approved, as well as UL listed (for U.S. and Canada) for roll grooving and welding for use in fire protection COMPARISON systems with a working pressure of 300 psi or less. Please check with appropriate sources for up-to-date listings and approval information. As an added benefit, it is more economical to use than schedule 10 due to reduced delivery costs and ease of handling. Furthermore, Eddy Flow's larger ID provides an opportunity for downsizing and further cost savings. INSTQE1EEMEII1EI msiznin WFlo 11/4 1.660 1.530 1.442 1.380 1.98 1.00 11/2 1.900 1.728 1.682 1.610 3.44 1.00 2 2.375 2203 2.157 2.067 2.78 1.00 21/2 2.875 2.705 2.635 2.469 1.66 1.00 3 3.500 3.3.34 3.260 3.068 1.00 1.00 4 4.500 4.310 4.260 4.026 1.00 1.00 * Corrosion Resistance Ratio BENEFITS Dual Certified to ASTM A135 and A795. FM Approved for roll grooved, and welded, and plain-end application in wet systems. UL Listed (for U.S. and Canada) for joining by welding or by listed rubber gasketed fittings for use in wet, dry, preaction, and deluge type sprinkler systems. UL Listed (for US and Canada) and FM Approved for use with Victaulic® Fl7w Fittings in plain end applications. Lightweight - saves shipping costs, and offers easier handling. Can be used with roll grooved couplings or welded outlets for pressures up to 300 psi. Floor stock available in various lengths produced in Casa Grande (AZ), Gerald (MO), and Masury (OH). Also can be ordered in custom lengths.. o Can be used for wet and dry* systems. * Eddy Flow can be hot dipped galvanized to meet FM's requirement for dry systems. PIPE PREPARATION For proper operation, all pipe surfaces should be cleaned prior to installation. In order to provide a leak-tight seat for the gasket, pipe surfaces should be free from indentations and projections from the end of the pipe to the groove. All loose paint, scale, dirt, chips, grease, and rust must be removed prior to installation. Failure to take these important steps may result in improper coupling assembly, causing leakage. Also, check the manufacturer's instructions for the specific fitting used. 1819 Clarkson Road For additional information, c®usj14i Chesterfield, MO 63017 contact your salesperson today at 4l, 6 LISTED (800) 325-4467 (800) 325-4467 or (636) 537-2600 BULL MDDSE TUBE CONIPANY FAX: (636) 537-2645 in the USA, or from Canada _______ www.bullmoosetube.com call (800) 882-4666 <13> AcBFOlcompany e-mail:sales@bullmoosetube.com APPROVED All information contained herein is accurate as known at the time of publication. But Moose Tube reserves the right to change product specifications without notice and without incurring obligation. 8/08 A Lightweight Schedule 40 Replacement Pipe That Has a Corrosion Resistance Ratio of 1.0 Bull Moose Tube Company has been making pipe for a long time and is recognized as a producer of quality pipe products. Eddythread 40 is designed with the same thoroughness as our other fine pipe products and now our customers have an option to buy a carefully designed replacement for Schedule 40 that: Has a Corrosion Resistance Ratio of 1.0 Has a Pressure Rating of 300 psi Is Lighter Weight Than Schedule 40 Is Approved by Factory Mutual and Listed by Underwriters Laboratories Is Produced in Accordance to ASTM A-135 and A-795 Can be Used With Standard Schedule 40 Threaded Fittings, Couplings and Valves Is Produced From Steel With Excellent Properties of Strength and Threadability Can be Used in Wet, Dry, Preaction, and Deluge Type Sprinkler Systems* Offers Lower Freight Costs EDDYTHREAD 401SPECIFICATIONS t1D!'(i) BEDE!E(SIZE. 1 1.461 1.083 Li 11/4 2.070 1.418 51 11/2 2.547 1.654 44 2 3.308 2.123 30 CORROSI ON mI. mi. 11/4 1.00 1.00 11/2 1.00 1.00 2 1.00 1.00 * Eddythread 40 can be hot dipped galvanized to meet FM's requirement for dry systems 1819 Clarkson Road For additional information, Chesterfield, MO 63017 contact your salesperson today at C®US BULl.. MOOS TUBE COIVIRANY (800) 325-4467 (800) 325-4467 or (636) 537-2600 LISTED E FAX: (636) 537-2645 in the USA, or from Canada _______ www.bullmoosetube.com call (800) 882-4666 A (CAFARO company e-maiI:sa1es(bul1moosetube.com <i~> *ppqoveo All information contained herein is accurate as known at the time of publication. Bull Moose Tube reserves the right to change product specifications without notice and without incurring obligation. 8/08 Page 2ot2 Tt'Pf 850 Figure 772 Grooved Coupling Maximum available gap between pipe ends. Mmnrtrow gay = 0. - - Manhrrure pressure and end lead urn rural from all loads based on standard weight steel pipe. Pressure rulings and end loads may differ on ether pipe materials aroilur wan thickness. Contact ryeo Fire Products for details. See Fire Protection Equipment Submittal Sheet for Listing and Apprenul pressure ratings. Gold color ceded metric bue sees em available upon request Man End step tutor out grooved standard weight pipe, vetoes for roll grooved pipe will be 15 firer 01 Out grooved. Figure 772 Rigid Couplings have an Anti-Rotation Feature of 'oripping teeth' along the coupling keys in sizes 1/.' - 4', which make the Figure 772 perfectly Suited for 'arm over installations where the likelihood of rotation is greatest This feature reap eliminate the need of eotrw hangers Is support the urn overdue to Increased rigidity and gripping terse saslng One and cost. General Notes: It sore Designer's responsibility to select products suitable entire intended service arid to ensure ISO that pressure ratings and pedonnamree data in not exceeded. Always read 004 understand the installation 9001 mnstrsmorlows Ire-react, Never remove any piping component erverreur or modify any piping dnfmotermu8es uulthnut Cr51 depressunmeing and draining the system. Material and gasket selection should be vented to be compatible for the specific application. Ceetihed Company TYCO FIRE PRODUCTS, 451 North Caweorr Avenue. Laesdaln. Pennsylvania 19946 Printed U.S.A. Prune frffl EodGap Mau.f Pres 51 sure Meet EedLoad ' Nominal Dimeesigns Net WE O.D. A B C Size Inches Inches psi Elms, Inches Inches Inches .o,, iZO mm mm kPa N mm mm mm Dma. e Lg. Di Kg, nrA. 1.660 0.06 300 649 2.75 4.38 1.81 °4'02'/.' It) 42,4 1.5 2,068 2,867 69.9 111.3 46.0 MI0v57 0.5 1r4. n.gso 0.00 050 i,4n7 3.eo 4.62 n.81 W52'/.' n.O 48.3 20 3,447 6,303 76.2 117.3 46.0 M10iv57 0,5 2,375 0.13 500 2,214 3.41 Slat 1.80 a 2r1.' n.5 60.3 3.3 3,447 9,840 86.6 130.0 47,8 M10v57 0.7 2½' 2.875 0.13 500 3,244 3.91 5.63 1.88 a4' 02r/a' 2.5 73.0 33 3,447 14,4.30 99.3 l43,0 47.8 Mt0,v57 1.1 3.000 0.13 300 2,120 4.16 5.72 2.00 2.8 76.t 3.3 2,068 9,430 t06.4 145.3 50.8 MI0o57 1.2 3.500 0.3 500 4,800 4.63 6.25 1.88 39'02W 2.6 88.9 3.3 3,447 2n,387 1t7.6 158.8 47,8 MIO,e57 0.2 7,948 5.8n7.501.97Wg2'/a'3.5 +4.5000.19 000 3,44735,353 047.6 090.5 50.0Mt0ue57 0.6 139.7,r.,,300 7,1277.029.72 2.06 Ml6e83 2,068 31,700 t78.3 246.9 523 3.4 5.563 0.19 300 7,280 7,09 0.71 2.04 5yl 83r/. 75 04.3 4.8 2,068 32,417 180.1 246.6 5t.8 M16x83 3.4 168.1.... 6.500 0.n9 300 9,950 8.09 10,53 2,13 7.6 165.1 4.8 2,068 44,258 205.5 267.5 54.1 Mn6x63 3.4 6' 6.625 0.ig 400 n3,752 8.09 10.53 2.13 34' 03½' 7.6 168.3 4.8 2,758 6t,302 205.7 767.5 54.1 Ml6c83 3.4 8' 6.620 0.19 455 26278 10,56 13.56 2,62 14'x415' 18.0 219.1 4.8 3,103 f06,085 268.2 344.4 66.5 M20x 12 8.2 no.750 0.13 200 22,679 12.84 16.4n 273.0 3.3 1,724000.876 326.t 416.8 M24x 165 11.2 12'12.7500.13 25 31,90315.41 3239331724141905391.4 r n'06W24.6 M24ur 165 19.1 GrinnellGrooved Fire Protection Products Figure 772 Rigid Coupling - Patented General Housing: Ductile iron conforming to Should be contacted relative to any questions. ASTM A-536, Grade 65-45-12 Description Protective Coatings: ndyinnpainnentnnustbeimrnedlaoetycorrected. It is recommended that automatic sprinkler Non-lead orange paint systems be inspected, tested,und maintained by Fire brigade red (optional) eon-lead point a qualified Inspection Service. llot dipped galuantied conforming to ASTM , 6-153 Limited VdS(J ASTM A-f 83, Zinc Plated, (Mm. Tensile HottiNutro Truck Head Bolts - conforming to 110,000 p57758,422 kPa) UL Warranty Products; manufactured by Tyco Fire Products are See Fee Protection Mc - corming la ASTM FG65M FM Suntr,nutut Street for Cadent (speedy when ordering) 5krn000darrdwmaWh6pe1usrgs11 Preseare Reeng Grade A EPOMAsiolet color code Whaekl lorarCpwrednrfahseiranJernnnt ussneyriurpronul Intonenation amhmenttoen507F(+66C)forhreprotecniun umaaodesrm1tsunantywilejrehen(10junans systems. Not recommended for hot water igum772WjudCeongpmwineangijnAoby from date of stritennunt by Tco Fire Reah No firmly gripping along the circumference of the pipe systems. • Tei-sedi(GradeEEPDM(,grnencolorcede eroecfa sswarranty, is given Ion products or components CEodbyrmenotatttstodbyeveastju g- Rigid ccegSE am for use in dry pipe or freezer systems. arklIreezer aptmrnuRgune772RgajCcupfngs usiSTycoPinFiodusoroepesaJrmjnqrgs Peelubricated (Grade A EPDMA( amaproeld0trmisbklnatoroeiotpen.ng REearei (See Data Street TPP1895 for oldie Selecting ndudrhambeeusudtenuer.reru,atrpwywey esnyoeakctrfmrercOhenlersfagrotfnatstahnej, man pro w0perg05k0t( ash gdenpos.ttwcapableefptamsunsuptusetls1eig modifod or repaired in amoobouw with apoAruuue (3847k a) dDiet on apesire am uaSthklorec when used in fire Profffictioni . Ordering StandardsStandardsof ore National the PgilecliourAsroxtatien QRPA),aelfor8atESeboticofatryertdecoujtcaobe RigdCeawtouusreonmmeodedleethyplpeaoeJ Procedure Erasing ,hodeuistmit. Mateetabs board by Tw Are Fiodictu to be detective deal tat eioatn tspnhet on below applications. WAN= When placing an order, indicate the lull product rob.atTouAnePmothsts'odeophcus Twelve PledrrmaooerREeeadaedwe The ftyure 772 Rigid Goupfiog described hereto name. Pleasespeofytnequanhty,sgurnnumber, ucts my pooun musibeirwollndaodeuaissthtofirrconmnpednorueth type stgasket, Grade "A* EPOMA. Prelabrfcated 0dideenenrv.Wasudffi0maiplSubkodrMaofs )GIadrWEPOMA(or5radeE"EpDMTni-Seat , the sale of products argues of Products. Typo Are ofthe8biaosaldenWhmckundoraodripn,tsadoitsin and size. to the standards of any other aufhusitios lousing GindtimosedFjuetPm ,votee,ssories design emorsor jurisdiction. Failure (ü do so may Impair B5 and Other products are available throughout Ore suppled by8rynror&gufsrgunsentaticet. purlonnanro of Ihic device. U.S.,Thnaandinfoma5otsa1y,thmughaneyuoth is 90 RANT SHALL. TYCO ARE Ff10011015 RE LIABLE,negsgcrjogt,smtcrituutygg The eager is mnqamsrbic tnrnta/rrla1nic4 their fire ofdictibdioncectems You nnaywriledirectly urcag pmntom2inn syotem and devices Arproperopenaling 215-362-0700 fsrthe distributor leanest you. condition The instatIng contractor or syenldnr 90 f.S00 L8dS5LDllMAGES, nsonufadsanrslonublbecentsctadutlhauryquectzmro Care and P62JJODIGBLTfNOTUIAI100TOLABORO58GW REG60DLOFWh00AREPR50I35S Technical Maintenance DAMAGES WHS68ORMEDABOUTT1IEF03SOIUIYOFG.ICH MD The owner Is responsible for the Inspection. Data N90 RRE PRODLtCl5'U 00 ABllJ1YThE0pp1HotoLpgfEoljyj, testing, and maintenanceof their fine protection 1O1f1ESo.LW PRICE Figure: 772 system and devices in accordance reds the I1ERE WARR4R1YStMREWEILAREJLF Stem: 1A'-12' appl65btastandardsoltheNahonalAreProtection AHVAMAIL MW WARRAN7E1WW$3WI Approvals: UL, FM, ULC, VdS. and LPCB: Hssoclatiur (e.g., NFPA 25). in addition to the IMPLIED. INCLIlOING WARRANTIES OF See Are Protection Submittal street for exact standards of any authority having jurisdiction. MERC7I4NT4.BII.fTy AND FITNESSP081 A Listing/Approval information. the'etstallingcentnactonorpreductmanulacturer PAA7FAJRPRI Page 1 of 2 July 2004 TFPIISSO tLJCO/Fire & Buil ding Products Technical Services: Tel: (800( 38 -9312 I Fax: (800(791-5500 wwW.tyco-fire,com tIlCO/Fire & Building Products Technical Services: Tel: (800) 390-9312/ Fan: (800) 791-5500 www.tyco-fire.com Grinnell Grooved Fire Protection Products Grooved Fittings General Material: Limited Cast hgures:201,210, 219250260,501,510, Description 519. 5100E. 5015.5105 and 51 OS- Warranty L [Ill See Fire Protection Ductile iron conforming to ASTM A-536, da0$ ctsrot by Tyce Her Products am Soberlttal Sheet for Grade 65-45-12 rnrnanrwt soiety to the original Buyer for ton (10) PressoreRetvrgand Fabricated Steel: Figures 391. 392, 393, 312. yrarsairectetectsrirnterwiuwiwcersiip USIng/Approval 313, 321, 327, 341 and 350- Carbon vi wtonpaidforaedpmpertyirctafedandmainlairrud Information (Sizes 1'/( - 6a5 Schedule 40) under normal use and service This warranty will (Sees 8 - 12 are Schedule 30). expire ten )to) years fmmdate elshipmontbyTyco conforming to ASTM A-53 Grade 8 Ore Products. No warranty icgicen for products or The grooved1101ngs provide anee000rorca1 Protection Coatings: components manufactured by companies not aardefficientnnethodofchangingdirectioe, Non-lead orange paint affifotedtryownemshipwitrlyco9toPrortuctoortor adding an outlet, reducing, or capping Fire brigade sri (optional) eon-lead paint pmodantsaodcomporrortswtnicirfwaebeensobjoct grooved piping systems. Grooved fittings • Hot dipped galvanized rantomnring to ASTM to ~isuw.inVroperirGtfton.conosion.orMkh are available in durable ductile iron or A-153 have not been rooted, nrainlainvd, modified or labncateei steel as indicated. mpahodin accordance with applirabteStandardoot Note: Figure 51ltS and 519S fittings are Ordering Ore Notional Em Protection Association (NFPA), special short radius fittings with smaller cooler In end dimensions than standard Procedure andfertlrestandardsolanyettrorAuiltontlnsHaving Jurisdiction, by Tyco Fee Products grooved fittIngs. Depending on the size and When placing an order, indicate the full product tobedetoclive shall heeillreempairedor replaced, at ceopling used, there may be interfereeces at name. Plane specitythe quantity. sgumnumhor, Tyco HneFroducfo'sohoption. Tyco Fire Products the ball pads that requkerepasitioniegotlbo wall oriclmess,and size, neither assurers, nor au0lorizes any person to coupling orientation. The use of flange Grinnell Grooved Piping Products, valves, assunstorit.argothvrobtigahoniozerneclionwilb adapters is not recommended with Figures accessories and ether products are available the raleotpmdietror parts of products. Tyco Am 5105 and 510$ fittings. Contact Tyco Fire rirroughounlho U.S., Carrada, and intematiovally, Productushallnotherosponsiblelorsprivldonsyslenn Products for details, through a network of distribution centers. You droignomnotsoriooccuraruorinrengletnintennralion WARN016 may write directly or call 215-362-0700 for the supplied by 01qleror Nyser's tvpresevtalsos. The Fittings described heroin must Ito installed distributor nearest you. IN 183 EVENT SHAIJ, 1550 FIRE PRODUCTS BE andmaioedincnmpliavcewithlhisdocaaner0 LIABLE IN CONTRACT, TORT, STRICT LIABILITY as rue/I as with the app/wail/v standards , r Care and DR UNDER ANY OTHER WIN. THEORY. FOR INCIDENTAL. INDIRECT, SPECIAL OR National Fire Protection Association, in addition Maintenance COu9DIoI0$RNT0$T to floe standards otary' other authorities having jurisdiction. Failure to do so may impair file The owner is responsible for the inspection. LIMITER TO LABOR CHARGES. REGARDLESS OF performance ofthisdordce. testing, and maintenance of their6m protection WHETHERTYCOFIREPRODUCTSWASIN0$RMED The owner is responsible for maintaining their system and devices in accordance with the ABOUT THE POSSIBILITY OF SUCH DSMAGES, lime protection system and devices in proper applicable standards ol the ldationaiFimProtection AND Ill NOEVONTSIiAILIYCOFIREPRODUCTS' operating condition. The installing controdtoror Association (e.g.. NFPA 25), in addition to the LIABILITY EXCEED AN AMOUNT USUAL TO THE spninhfermanutactomruhoaldbecentacoedwilh standards of any authority having (orisdictioo, SOLES PRICE any questions. Thninstailingcontractororpmductmanulacturer QE WA AN YMA196 KFLJ 650 should be contacted relative to any questions. ANYAIP ALL fl11.W4PJL4N17ER96WI91 Technical Any impairment must be immediately corrected. IMPLIED. INCLUDING WARRAAITIES OF It is recommended that automatic sprinkler MERCIIA.NTA2IL?TY AID FIIWLSS FOR A Data systems be inspected, tooted, and maintained by PAR1BT,8_ARPfIfFI. Approvals: a qualified Inspection Service. Ut, FM, ULC. VdS, and LPCH: Note: See Fire Protection Submittal Street for enact tasting / Approval information. Page 1 of 6 September 2004 TFPI8IO Page 2rot6 TFP1815 Figures 201, 210, 219, and 260 cod' c e t Figure ant Figure OIU -con--) IOu..1 I on - Frgoer 060 Figure 219 0 .000tol.,Mrune,,00,go.wreary,, Fr,00 eavaru proauvS. ,.auuog ow ved osrer,,. uoeoo 50.0 oat '0 co.rvoeor,avo mu 005.sov ova. E.ae,plo. or 0 0' 0-rae, bruce r*rb (010050 toruS woo orA Sw re05r Oourw Stt5 Stee p 3,50 7.5 e t 4.8 1.2 58 128 12, 6,5 33 3.3 e nkp 1.2 1.8 2-2 3.0 5.8 _e. ~ - 4-5 7.0 52 41 525 10 .6 325 S. 3-50 14.6 18.5 6.50 c Friction Resistance' as Equivalent Sttaitt Pi ,(00$essed ) Size 8norrch Run inches Feet Four FEGi' Feet mm Meters Meters Meters Me rs 1W UT ST - - 42.4 0.6 0.3 1.5 06 TW WUT 2.3 48.3 0.7 0,4 1.8 0.7 3.2 UT Th 60.3 1.0 0.5 2.5 1.0 -Sw UT 730 0.2 0.6 3.0 1.2 4.1 2.1 10.3 4.1 76.1,., 12 0.6 3.1 t.2 -5- 4.9 85.0 1.5 0.7 3.7 1.0 16.3 TH 100.0,, 2.0 1.0 5.0 2.0 CT ITT Sw 004.3 2.0 0.0 0.0 2.0 '2.'04 w or 20.0 TH 133.9,.,. 2.4 12 6.1 2.4 8.0 4,1 20.0 8.0 139.7,,. 2.4 1,3 LI 2.4 5- 20.5 TH 141.3 2.5 1.3 6.3 2.5 - -ow 23.8 UT 159,0,., 29 0.4 7.2 2.9 - .s r 23.0 IT 165.1,, 2.9 1.4 7.2 2,9 ITT -93- 168.3 3.0 1.5 7.6 3,0 ITT TH 32.0 iTT 216.3,,,. 4.0 2.0 10,0 4.0 T ITT ThS W50 iTT 209.1 4.0 2,0 00.0 4.0 no is.s 8.3 41.3 16.5 273.0 5,0 2.5 12.6 5.0 12 19.9 9.9 49.7 19.9 323.4 6,1 3.0 15.1 6.1 Flgume20t Figure Floute219 Figsre26O5 - 45 Elbow 90' Elbow leo End Cap -- Nominal doE TR. CteE UT0$ cmuto O Inches Lbs. inches Lbs. Inches Ko. Lbs. i hes Lbs. nm mm ,)j65,,,, mm •j,, vms 570' 0.9 5Y0' 1.0 '$Y0' IA 0.88 0.4 44.5 0.4 69.9 0,5 69.9 0.6 22.4 0.2 Y0' Y0' 0' 0.05 44.5 0.0 69.9 0.5 69.9 0.8 22.4 0.3 -:- 2-00 TE WUT 20' e 2 20.8 0.8 82.6 0.9 82.6 1.2 22.4 0,4 - TD0' 3 0' 5 o T5 2/, 57.2 1.0 95.3 7.4 65.3 2.6 22.4 0.4 - TS0' 0' 0' TS 76. 2.25 57,2 1.0 95.3 1.4 95.3 2.6 23.9 0.5 2.va 55- 0' 20' OAR e.0 I.e . 105.0 .2.0 .720.0. 3,2 22,4 0.5 '590' 5T Y0' 11.5 - 108.0mw 73.0 2.5 720.7 3.9 120.7 5.2 - -3.05 T -OS T q5r T Sw 76.2 2.4 027.5 3.0 127.0 5,4 25,4 1.2 '550' 5AR flTh - n33.nnrm 82.6 3.5 133.4 5.1 133.4 4.8 - - 7.7 5AR TO 5e -iSw o 4.7 13e.7tnrn 82.0 3.5 739.7 5.1 139.7 6.9 23.4 2.1 -'501 05- TT TSw TT W itel 55- 82.6 3.9 139.7 6.1 139.7 7.7 25.4 2.3 - w -oss BAR 13.9 - 159.0mw 88.9 5.4 752.4 6.6 752.4 6,3 - - - 5O- TT5 38.0 '501 165.1mm 88.9 5.4 165.1 0.4 165.1 ft.8 25.4 3.4 '501 13.0 T1 '501 88.9 5.4 065.1 8.4 165.1 11.8 25.4 3.4 4.25 23.0 7.75 38.5 7.75 45. 23.0 7.7S 60. 0 216,3mm 108.0 00.4 966.9 16,0 196.9 20,4 - -- '501 5Sw 1 lIT 8 108.0 15.4 196.9 16.6 196.9 20.4 30.2 5.0 - lIl 5Sw 1 '501 7IT lIT $Sw 10 120.7 14.1 228.6 27,2 228.6 32.7 31.8 9.1 551 'TNO" TOSS THIS" TOSS '01UT 'FIT se.o 133.4 18.0 254.0 30.4 254.0 42.0 30.5 16.3 Page 3ol6 1091810 Figures 501,510, 519 and 51 ODE CE Figure 591 Figure 510 Figure 519 Figure 51 ODE FigureSol Flgure5lo I Figure 519 figere5looE 45" Elbow 90 Elbow Toe 99" Drain Elbow rectA N.App. I...Lbs. Inches W'Lb.. toE Inches Us.ze Lbs. Inches -- Inches -- Inches 80 WI. mm Kg. mm Kg. mm K. mm mm mm 44.5 0.4 69.9 0.5 69.9 0. 1.75 1.7 2.75 12 2.76 1.8 - - - 44.5 0.5 69.9 0.5 69.9 0.8 - - - - -2.00 2 TW 3 325 2.7 - - - - 50.8 0.8 82.6 0.9 82.6 1.2 - - - - 57.2 7.0 1 3.75 95.3 7.4 96.3 2.6 95.3 2.00 59.0 2.75 69.9 2.7 7.2 3. 2.50 63.5 7.6 425 108.0 20 - 158.0 - 3.2 or 700.0 59.4 2./5 699 Y 7.7 -:- ®- -8.5 ® 11.8 525 2.75 1. 76.2 2.4 127.0 3.9 7270 5.4 127.0 72.4 69.9 3.2 51 325 82.6 -9 - 3,9 r 739.7 6.1 739.7 17.0 7.7 g 739.7 85.9 2.75 69.9 5.9 -3.50 6 88.9 5.4 3g 765.7 8.4 625 765.7 2 11.8 625 765.7 3.92 90.6 0 69.9 6.1 Z50 108.0 0 10.4 7Y 796.9 76.6 796.9 .o 20.4 ?Y 196.9 725,7 7r 69.9 26 71.9 Figures 501S, 510S and 519S Figure 5015 Figure 510S Figure 519S" Fnchon Roselunce 501 .510S 5180 & 5790 (Expressed as Eqoicalent SIbsgt Pipe) Size 90" 45" Bronchi.Run Inches 't I mm Mcicrr l4elcrr 7687cm 6967cm r 1T 32 60.3 7.0 0.5 2.5 7.0 2.0 9.8 --g- 710 7.2 0.6 3.0 7.2 T 1.2 0.6 3.7 7.2 - 88.9 - 7.5 T 0.7 3.7 7.5 4 6.5 3.3 16.3 6.5 174.3 2.0 1.6 5.0 2.0 139.7- 8.0 4.1 20.0 8.0 2.4 7.3 6.7 2.4 5 8.2 4.1 20.5 8.2 747.3 2.5 9.5 4.8 23.8 2.9 7.4 7.2 2.9 6 9.9 5.0 24.8 9.9 168.3 3.0 8 13.1 6.6 32.8 13.1 219.7 1 4.0 2.0 70.0 4.0 Page 4ol6 1091818 Figures 250 and 350 Figure 250 COSI t.-EnE-1 Figure 350 Febricoled Srzes 3" 706" Figure 350 Fabricated Sizes 8" 7012" sns: lure ne enr..r550..,ufl.,.errye,ewc& nozeosOcex. Slect ,.low,r on eos.r,.0 , only c,.exluc 0n One foorl,nll,0. ADA CAP® Patented T0 9;J tS0?thcn,dsnau.e,,tnl,,pon rmuw.. - Figures 250 and 359 Concentric Reducer - Greece c Groove - - Nominal E to E eppc. Wt. ldorninel E to E Appe. Wt. Nominal Etc E 8990. WI. Size Inches Lbs. Size Inches Lbs. Size Inches Lbs. /n00rn mm Inches mm _®. Inc s mm 2.50 1.0 3.50 4.2 4.00 5.8 2014 63.5 0.5 e 88.9 79 605 007.6 2.6 h 12.2 2.50 1.3 3.58 4.4 5.05 201/c 06 139.7,.... 04 9 20 802 127.0 5.5 2.50 1.2 3.50 4.6 5.00 12.1 21,02 635 05 Sell, 00.9 2J 802/c 127.0 5.5 2.50 1.5 3.50 4.6 5.00 72.0 76.1..., 0 7,5 63.5 07 502 88.9 2.7 803 ivo s.s 2.50 1.6 3.50 4.5 5.00 11.8 76.1.o 2 63.5 0.8 502/, 88.9 2.0 804 727.0 6.4 2.50 1.3 1.50 4.4 5.00 11.3 3074 35 59 503 88.9 2.0 8c5 127.0 5.7 2.50 1.3 'S 2.50 4.5 5.00 10.8 301,4 63.5 0.6 04 88.9 2.0 806 827.0 4.9 2.50 1.3 4.80 5.5 0.00 21.9 302 63.5 8.6 165.1,,s3 707.8 2.5 10.4 752.4 l0.0 3.00 1.5 '165.1 4.00 6.0 6.50 21.6 302,5 76.2 0.7 ,0 107.6 2.7 1000 752.4 9.8 3.00 2.0 4.00 5.6 6.00 21.1 3076.1.,,. 76.2 0.8 165.1-139.7_ 707.6 2.5 1006 7524 96 3.00 22 '6 4.00 6.0 6.00 79.5 4014 762 1.0 02 707.6 2.7 1808 752.4 8.9 28.0 4s1,5 70.2 70 60 2/s 707.6 2.7 1204 72.7 3.00 2.3 4.00 6.0 30.0 3.00 2.3 4.00 6.0 47-' 4n2 762 70 60 76.1..., 701.6 2.7 1206 3.00 2. 4.00 6.0 2402,4 76.21.0 60 3 707.62.7 7208 11, e _________ 30 32 •4.004e76176.275 64707.6 27 12 010 .8 75.0 3.00 2.6 . 4.00 6.3 403 76.2 7.2 60739.7,., 101.6 2.9 ,11). Nominal oirna.si-s Inches -i Inches nches, Kg. Inches Inches Inches 1.25 31.8 1.75 44.5 1.09 48.0 8.77 0.3 1.25 31.8 1.75 44.5 1.89 48.0 0.77 0.3 1.800 48.3 1.37 34.8 2.00 50.8 2.02 57.3 0.88 0.4 1.25 31.8 1.75 44.5 7.89 48.0 0.92 0.4 1.25 31.9 1.75 44.5 7.89 40.0 0.92 0.4 2.375 00.3 1.37 34.8 2.00 50.8 2.02 51.3 7.06 0.5 1.47 37.3 1.97 50.0 1.89 48.0 728 0.6 1.47 37.3 1.97 50.8 1.89 48.0 128 0.6 2.875 73.0 1.37 2.00 508 2.02 LL 1.50 0,7 - Page 5of6 'l'FPIOlO Figures 391, 3929 393, 312 and 313 392 Figure 391 HE0E - -f1Ei1I-393 Figure 312 cv 313 Figures 327 and 341 01 1 Figure 327 F 150 5341 - e. FIa00r Adapter rrr1\ Nominal ppe.vrrt. JJ_O_.ILL mm.!L - LI.L../'N.........jJjl GeE 275 2.2 4.00 3.2 65.9 2.0 101.6 1.5 -L Figure 327 - --__I 2 - to Ô --- 2 /95.3 2.3 101.6 3.6 4.25 7.1 4.00 10.2 too.o 3.2 101.9 4.6 00 70 04 152.4 78 I 5.50 17.1 6.00 21.4 101 1397 7.8 152.4 07 I 4.50 6 6.00 26.5 165.1 12.5 152,4 11.8 -I 8 7.70 47.0 6.00 38.4 Figure 341 - _J-_ _iL 10. 9.00 60.0 _L2. _1ZL. 8.05 65.0 228.6 30.8 203.2 29.5 10.00 107.0 12 0.00 91.0 254.0 45.5 203.2 41.3 6oj6 TFP1010 Page Figure 321 ,c0I Figure 321 General 0010w lw ho Dosigner's responsibility to select products suitable for the intended service 458 to ensure ISO that pressure ratings and pertonnance data dnoteeceeded. Always mad and understand the installation instructions 9001 (IC-bOO). Never -move any piping component or correct or modify any piping deficiencies without first depressurizing and draining ft system. Material and gasket selection should be vorilind In be r.cerpatlble for theapplication. specific Certified Company TYCO FIRE PRODUCTS, 451 North Cannon Avenue. Lzrtsdale, Pennsylvania 19946 Printed U.S.A Figures 391, , Figure 312 Figure 313 and 393 Adapter Nipples 22/? Elbow 119? Elbow - NenrinJ EteE Iou/rae lbppo.Wt. CIoE Ai. 0106 4pps.Wl, Siso Lbs. Inches Lbs. Inches Lbs. 4.00 0.0 1.70 0.4 l.30 0.4 101.6 0.4 44.5 0.2 35.1 02 11/1* 4.50 0.9 1.75 0.5 1.30 0.5 101.6 0.4 44.5 0.2 35.1 9.2 2 4.00 12 1.88 0.6 1.35 0.6 101.6 0.5 47.8 0.3 35.! 0.3 2/s 4.00 1.9 2.00 0.7 1.50 1.1 101.0 0.9 50.8 0.3 38,1 0.5 4.00 2.5 2.25 1.4 1.50 12 101.6 1.1 57,2 0.6 38,1 0.5 4' 6.00 5.5 2.53 2.4 1.75 2.2 152.4 2,5 66.8 1.1 44.5 l.0 1. 6.00 7,4 2.68 4.1 2.00 3.3 152.4 3.4 732 1.9 50.8 1.5 6 • 6.50 9.5 3.13 5.6 2.00 4.6 152.4 4.3 79.5 2.5 50.8 2.1 8 • 6.00 14.2 3.80 11.1 2.00 8.7 152.4 6.4 98.6 5.0 50.8 3.9 8.00 27.0 4.38 14.0 2.13 9.1 203.2 12.2 11,3 94 54.1 4.1 8.00 33.0 4.88 22.0 2.25 16.7 2032 15.0 124.0 10.0 572 7.6 HIM 121 4uclrg Ten - Nominal CbS 69p0. WL Nominal C toE Appo. Wt. Size Inches Lbs. Size I hes Lbs. Indmen em, Inches eta, lteelbbelte 60604 à°i n 12.1 2 2 1½ 332 2,7 6 6 5 6.50 27.0 a 82.6 12 165.1 12.2 2½e2½o114 '' 80802 7.75 362 2½02½o1½ ' 80803 3.75 7.75 36Z 425 5.3 5.5 c 5 r5 2 8.8x4 36.6 95.3 2.0 190.9 16,6 l'h 8 36,6 O 0 108,0 24 196.9 .161.. 3030 108.0 2.5 196.9 16.8 2½ 10 10 2 9,00 57.1 O 0 108.0 06 228.6 25.9 4 4 fr/ 5.00 9.6 fg 9.00 57.4 ° ° 727.0 4.4 228.6 26.11 4 its '° 10 10 4 9.00 57.6 n 127.0 4.5 228.6 26! 4 4 2 5.00 10.1 10 10 9.00 57.8 ° ° 7270 46 220.6 26.2 2 4.08 8 6 6 7,7 5-50 15.8 5 37.0 4 4 2½ 5.08 10.3 10 10 6 920 58.0 O 0 127.0 4.7 ° 228.6 26.3 5.00 10.5 10 10 8 0.00 56.4 127.0 4.8 228.6 26.5 500o2 &38 t4'5 1201203 10.00 802 135.7 6.6 254.0 36.4 50502½ 5.55 14.0 1201204 10.00 80.5 139.7 6.7 254.0 36.5 505 c3 5.50 152 1201205 10.08 80.7 139.7 4.9 254.0 36.6 50504 120 1206 10,00 00.9 139.7 7,2 254.0 39.7 606026.5026.5120120810.0091.4 765711.9 254.041.5 1-0 50602½5012012010l0.00 91.6 41.6 60603 8.50 26.5 Fig. 200 - "Trimline" Adjustable Band Hanger Size Range - 1/2 thru 8" pipe Material - Carbon Steel, MU. Galvanized to G90 specifications Function - For fire sprinkler and other general piping purposes. Knurled swivel nut design permits hanger adjustment after installation. Features - (1/2" thru 2') Flared edges ease installation for all pipe types and protect CPVC plastic pipe from abrasion. Captured design keeps adjusting nut from separating with hanger. Hanger is easily installed around pipe. (2/" thru 8" Spring tension on nut holds it securely in hanger before installation. Adjusting nut is easily removed. Approvals - Underwriters' Laboratcries listed (1/2" thru 8") in the USA (UL) and Canada (cUL) for steel and CPVC plastic pipe and Factory Mutual Engineering Approved (3/4"thru 8"). Conforms to Federal Specifications WW-H-171E, Type 10 and Manufacturers Standardization Society SP-69, Type 10. Maximum Temperature 650"F Finish - Mil. Galvanized, For Stainless Steel materi- als, order TOLCOTM Fig. 200WON, Order By - Figure number and pipe size - Dimensions Weights - Pipe Rod Size Max. Rec. Approx. - Size Inch Metric A B Load Lbs. Length 1/2 3/8 8mm or 10mm 3V8 2 /8 400 11 3/4 3/8 8mm or 10mm 3/ 21/2 400 11 1 3/8 8mm or 10mm 3 /8 2 /8 400 12 11/4 3/8 8mm or 10mm 33/ 21/a 400 13 11/2 3/8 8mm or 10mm 37/s 21/ 400 14 2 3/8 8mm or 10mm 41/2 3 400 15 21/2 3/8 10mm 51/8 4'/5 600 27 3 3/8 10mm 57/6 4 600 29 3'/2 3/8 10mm 73/8 5'/4 600 34 4 3/8 10mm 73/s 5 1000 35 5 1/2 12mm 91/ 61/ 1250 66 6 1/2 12mm 101/ 6'/4 1250 73 8 1/2 12mm 131/ 83/4 1250 136 Main Off ice(Manulaclunnq Facility .nl1J)I1 r1 • Cn'i:2. (:1 s 19.0 n h91. r. 9.1T01 Customer Service • www.tolco.com Fig. 98 - Rod Stiffener Size Range - Secures 3/8 thru 7/8' hanger rod Material --- Carbon Steel Function - Secures channel to hanger rod for vertical seismic bracing. Finish - Electro Galvanized Note Available in HDG finish or Stainless Steel materials. Order By - Figure number Fig. 99 - All Thread Rod Cut to Length res 3/8" thru 7/8" rod in 1" incrTrTnts Material - Carbon Steel Maximum Temperature 750°F Finish - Plain Note - Available in Electro-Galvani zed and HDG finish or Stainless Steel materials. Order By - Figure number, rod diameter, rod length and finish Dimensions Weights Rod Max. Rec. Load Lbs. Size For Service Temps 650°F 750°F 3/8 610 540 1/2 1130 1010 5/8 1810 1610 3/4 2710 2420 7/8 3770 3360 Fig. 100 - All Thread Rod Full Lengths Size Range - Secures 3/8" thru 7/8" rod in 10' lengths Material - Carbon Steel Maximum Temperature - 750°F Finish - Plain Note - Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By - Figure number, rod diameter and finish Dimensions • Weights Max Rec. Load Lbs, Rod For Service Temps Approx. Size 650°F 750°F Wt,/100 1/4 240 215 12 3/8 610 540 29 1/2 1130 1010 53 5/8 1810 1610 84 3/4 2710 2420 123 718 3770 3360 169 1 4960 4420 222 1'/ 8000 7140 360 1'/2 11630 10370 510 Main olflceiManulacluring Facility • 13i 9ip'.m tcc IA 129/9• ro 9.N /i '901. Fa.-, 901 /2/ 9230 I Customer Service '.YJ WwWtO!Co. corn 1irti!s] cus LISTED 11/4 16 (80) 1001-3 Xl 76(6 1001-3 X 11/4 168.7 (76,5) UL (100) 1001-4 Xl 1001-4 X 11/4 182.4 (82.7) IJL 6" (150) 1001-6 Xl 1001-6 X 11/4 211.4 (95.9) UL 8" (200) 1001-8 Xl 1001-8 X 11/4 238,8 (108.3) UL bee load ratings in UL Listed Design Load chart. * The loads listed are axial loads on the brace. The horizontal load capacity, H, of the brace is: H = F x sin ?, where ? is the installation angle measured from the vertical. / Fig. 1001 -Sway Brace Attachment Size Range: Pipe size to be braced: 21/2 (65mm) thru 8" (200mm) IFS. * Pipe size used for bracing: 1(25mm) and 11/4" (32mm) Schedule 40 IFS. Material: Steel Function: For bracing pipe against sway and seismic disturbance. The pipe attachment component of a sway brace system: Fig. 1001 is used in conjunction with a Fig. 900 Series fitting and joined together with bracing pipe per NFPA 13, forming a complete sway brace assembly. Features: Can be used to brace schedules 7 through 40 IFS. Field adjustable, making critical pre-engineering of bracing pipe length unnecessary. Unique design requires no threading of bracing pipe. Comes assembled and ready for installation. Fig. 1001 has built-in visual verification of correct installation. See installation note below. Installation Note: Position Fig. 1001 over the pipe to be braced and tighten two hex head cone point set bolts until heads bottom out. A minimum of 1" (25mm) pipe extension is recommended. Brace pipe can be installed on top or bottom of pipe to be braced. Approvals: Underwriters Laboratories Listed in the USA (UL) and Canada (cUL). For FM Approval information refer to page 65. Finish: Plain. Contact Cooper B-Line for alternative finishes and materials. Order By: Order by figure number, pipe size to be braced, followed by pipe size used for bracing (1" (25mm) or 11/4" (32mm)) , and finish. Important Note: Fig. 1001 is precision manufactured to perform its function as a critical component of a complete bracing assembly. To ensure performance, the UL Listing requires that Fig. 1001 must be used only with other Cooper B-Line,TOLCO bracing products. UL Listed Design Load Sch. 7 - 1600 lbs. (7.11kN) Sch. 10 & 40 w/1" (25mm) Brace Pipe 2015 lbs. (8.96kN) Sch. 10 & 40 W/11/4" (32mm) Brace Pipe 2765 lbs. (12.30kN) (. All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. COOPER B-Line C US LISTED 9 Set Bolt Included Mounting Hardware Is Not Included Fig. 980 - Universal Swivel Sway Brace Attachment - /8" to 3/4" Size Range: One size fits bracing pipe 1 (25mm) thru 2" (50mm), Cooper B-Line 12 gauge (2.6mm) channel, and all structural steel up to 1/4" (31 .7mm) thick. Material: Steel Function: Multi-functional attachment to structure or braced pipe fitting. Features: This product's design incorporates a concentric attachment opening which is critical to the performance of structural seismic connections. NFPA 13 indicates clearly that fastener table load, values are based only on concentric loading. Mounts to any surface angle. Break off bolt head assures verification of proper installation. Installation: Fig.980 is the structural or transitional attachment component of a longitudinal or lateral sway brace assembly. It is intended to be combined with the bracing pipe" and Cooper B-Line/TOLCO braced pipe attachment, Fig. 1000, 1001, 2002, 4L, 4A or approved attachment to pipe to form a complete bracing assembly. NFPA 13 guidelines should be followed. To Install: Place the Fig. 980 onto the bracing pipe'. Tighten the set bolt until the head breaks off. Attachment can pivot for adjustment to proper brace angle. Approvals: —Underwriters Laboratories Listed in the USA (UL) and Canada (cUL). For FM Approval information refer to page 61. Note: Fig. 980 Swivel Attachment and Fig. 1001, 1000, 2002, 4A or approved attachment to pipe that make up a sway brace system of UL Listed attachments and bracing materials which satisfies the requirements of Underwriters Laboratories and the National Fire Protection Association (NFPA) Finish: Plain. Contact Cooper B-Line for alternative finishes and materials. Order By: Figure number and finish. Pat. #6,273,372, Pat. #6,517,030, Pat. #6,953,174, Pat. #6,708,930, Pat. #7,191,987, Pat. #7,441,730, Pat. #7,669,806 Fig. 4L Fig. 980 Longitudinal Brace -I Part )1 .rUItg Number 'i( In Size......... Hdw 1A I . . .. .. (mm)(mm) ,MountingHoIe Pilax id (cIJLüs) Design " Appr& .wt.i.ioofr' lbs (kg) 1(llg Standard size. Cooper B-Line, Inc.'s ("Cooper B-Line") seismic bracing components are designed to be compatible only with other Cooper B-Line bracing components, resulting in a listed seismic bracing assembly. Cooper-B-Line's warranty for seismic bracing components will be the warranty provided in Cooper B-Line's standard terms and conditions of sale made available by Cooper B-Line, except that, in addition to the other exclusions from Cooper B-Line's warranty, Cooper B-line makes no warranty relating to Cooper B-Lines seismic bracing components that are combined with products not provided by Cooper B-Line. All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. COOPER B-Line R IlIUS and Hex Nuts Included Fig. 4A - Pipe Clamp for Sway Bracing Size Range: 4 (100mm) thru 8' (200mm) pipe. For sizes smaller than 4" (100mm) use B3140. Material: Steel Function: For bracing pipe against sway and seismic disturbance Approvals: Underwriters Laboratories Listed in the USA (UL) and Canada (cUL) 4 (100mm) thru 8' (200mm). Installation Instructions: Fig. 4A is the braced pipe' attachment component of a longitudinal, lateral or riser brace assembly. It is intended to be combined with the "bracing pipe" and Cooper B-Line/TOLCO transitional and structural attachment component(s) to form a complete bracing assembly. NFPA 13 guidelines should be followed. To Install: Place the Fig. 4A over the pipe to be braced. Attach Cooper B-Line/TOLCO transitional fitting, either Fig. 980, 910, 909, or any other Cooper B-Line/TOLCO approved transitional fitting. Tighten bolts and nuts; torque requirement is a minimum of 50 ft/lbs. (68Nm). Transitional fitting attachment can pivot for adjustment to proper brace angle. Finish: Plain. Contact Cooper B.-Line for alternative finishes and materials. Order By: Figure number, pipe size and finish Note: Please refer to Fig. 4L for longitudinal brace applications for 2" (50mm) - 8" (200mm) pipe sizes. ®TDLCD c®uS LISTED Fig. 4A - Longitudinal Brace Part No Size in (mm) 4 in (mm) ,. B 4iin (mm) rn ir JMx . 0 Bolt i) Size' Horiz'ntalIt Design Load t l lbs (kN) 'Approx. I. 100: lbs (kg) Cooper B-Line, Inc.'s ("Cooper B-Line") seismic bracing components are designed to be compatible only with other Cooper B-Line bracing components, resulting in a listed seismic bracing assembly. Cooper-B-Line's warranty for seismic bracing components will be the warranty provided in Cooper B-Line's standard terms and conditions of sale made available by Cooper B-Line, except that, in addition to the other exclusions from Cooper B-Line's warranty, Cooper B-line makes no warranty relating to Cooper B-Line's seismic bracing components that are combined with products not provided by Cooper B-Line. All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. COOPER B-Line APPROVED LAQ U W - IL MaX Iip UttTest t1F411 STe,ui, ILoacP WWOW PipeSize L1oail - CPVC1-1/2 300 1.5 CPVC1-1/2 300 1.5 2-1/2 850 1.5 X 4 1475 2-1/2 850 1.5 4 1500 1.5 X 4 1475 4 1500 1.5 X 4 1475 3-1/2 - 4 1500 1.5 X 4 1475 2-1/2 3** 1250 1.5 2-1/2 1250 1.5 3 1050 1.5 X 4 1475 4 1500 1.5 X 4 1475 3 1050 1.5 4 1500 1.5 B'X' PI 8007957 GST 10 8020957 SWG 10 8008957 GST 20 8068925 GST 20 SS 8010957 GST 30 8009925 GST 25-380 8022925 SWG 25-380 8021957 SWG 20 8073925 SWG 20 SS 8139957 SH GST 2O 8141957 SH GST 3O 8140957 SH GST 2OSS 8142957 SH GST 3OSS 1.5 1.5 1.5 1.5 1.5 1.5 IYS Minimum q)( PIN STEEL ut.; U MaxPixe ULTeSt' MnJmUJJ Stoel FM M Mle PM - Sie,in L Thn,n_ PipeSize toad Thiknsin OUJO( U11) A 4 1500 0.035 X 4 1475 0.1050 8037957 DSTR 1-1/2 X 4 1500 0.035 X 4 1475 0.1050 8039957 DSTR 516 X 4 1500 0.037 X 4 1475 0.1050 8045957 DST 516 X 4 1500 0.188 X 4 1475 0.1875 8046957 TEKSO X 4 1500 0.250 X 4 1475 0.1875 8055957 SWDR 1 X 4 1500 0.037 X 4 1475 0.0600 8056957 SWDR 516 X 4 1500 0.037 X 4 1475 0.0600 8054957 SWDR 1-1/2 X 4 1500 0.037 X 4 1475 0.0600 8137957 SH DSTR 1 X 4 1500 0.035 X 4 1475 0.1050 8150922 XP 20 X 2 750 0.027 X 4 1475 0.1050 8153922 XP 35 X 3-1/2 1250 0.043 X 4 1475 0.1050 BX P/N CQN CRETE FM FM Max FM Test Materpa) L Pipe Size Load 000' Li u X 4 1475 3000 PSI 8061957 SWC20 X 4 1475 3000 PSI * SWG 25-380 Maximum pipe sizein composite wood joist allowed by UL is 3-1/2" SWG 25-380 Maximum pipe size 'in wood timber or joist allowed by UL is 4" ** SWG 20 Maximum pipe size in composite wood joist allowed by UL is 2-1/2" ** SWG 20 Maximum pipe size in wood timber or joist allowed by UL is 3' UL and FM tests were performed in compliance with NFPA-13 Standards. Fastening requirement: 5 times weight of water filled schedule 40 pipe plus 250 pounds IT[vBuiIdex www.ftwbuUdex.Com ;, 800-284-5339 SSS26 MATFPIAI IIT FART: MATERIAL: HANDLE STEEL STEM ROD BRASS BALL C.P. BRONZE BODY BRONZE SIGHT GLASS VALVE SEAT tEXAN" IMPREGNATED TEFLON INDICATOR PLATE STEEL HANDLE LOCK SPRING SPIEL MODEL 1000 11 " " 2 TEST OF - .'.• . LI The AGF Manufacturing Inc. Model 1000 TESTANDRAIN Provides Both The Test Function And The Express Drain Function For A Wet Fire Sprinkler System. 0 The Model 1000 Complies With All Requirements Of NFPA-13, NFPA-13R, And NFPA-13D. LI The Model 1000 TESTANDRAIN Is A Single Handle Ball Valve That Is Light Weight And Compact, Includes A Tamper Resistant Test Orifice, Integral Tamper Resistant Sight Glasses, And Is 300 PSI Rated. 0 Available In A Full Range Of Sizes From 3/d' To 2" NPT & BSPT, With All Specifiable Orifice Sizes /81, 7/i6". 1 /2', 17/32", s/it" (ELO), 3/.*" (ESFR) and K.25. LI The Orifice Size Is Noted On The Indicator Plate And The Valve Is Tapped For A Pressure Gauge. LI The Standard Model 1000 TESTANDRAIN Valve Includes A Pressure Gauge Port Tapping And Can Be Ordered With A Relief Valve As A Model 1011 Or 1011 LI Locking Kit Available Which Provides Superior Vandal Resistance And Prevents Unintentional Alarm Activation. 00 OUT Now Auto 0, Visit us 4,0 on the Internet at I MODEL 1000 300 PSI A 3/4" In 11/4" 11/2" 2" ORIFICE SIZE AVAILABLE - 3/0.17/16", 1/2', 17/32, EL0(S/6). ESFR(3/4") and K.25 'Available on I /2" to 2' sIze ants oniy. DIMENSIONS - INCHES 616 RITA'' 1" 1I6" 1 1/27 2 /16" 3 tot" 2$,., 3 tot" 1 "Ile 4 910 6 'Ia" 1 1147 5 'Ia" sin,,,, 1 1I16 cm,,,,, 2 "116" 4/1 3 toit" "Ire"Ire 5 Stem,,,, O/' 4l39, 5 lj" 192.20oa1 1 1/ 2 6 1I6" aa.ss,, '3 1 'if 45309,1, 3 II' 81.009,9, 5 Ia" 27,97, 3 'to" 99.10$,,,, 2 sle 6&97,n., 8 I/4 oa.oaoa, 10 'Ia" 2fl.a0.a,, 2" L_.._._ 671,e- 1 7/I6" 4030 3 Ile 81309,7, 51/l6 27,9,1, 3 0s" 99.109., 2 5/fl" 6t07,.,, 8/1' 206.63,,.,, 10 OH" 273.609,9, Valve UL listed only. UI 115110510,114019 I Jf Um. PA IWSS JOB NAME: 11:(610)220-6900 lIP ARCHITECT: Roan: Ie700tostavdmI,teen Wcb:70w.3,,00n416n.6o,, _____________ __________ ENGINEER: 10"" CONTRACTOR FRONT ViEW/VERTiCAL INSTALLATION FROM BRANCH - GAUGEPROVIDED 032 SWEET EL TO DRAIN STREET EL OR PIPE TO DRAIN FIGHT HAND/STRAIGHT INSTALLATION APPROVALS: LI UL and ULC Listed 0 FM Approved except 3/4' U NYC-BSA NO. 720-87-SM !J CA. State Fire Marshall unuur ON ReVs 50 omen On souREr Pours to resents utu. tenser Is OPPOSITE nRrcnou OF -TERn- VSR-F (.1) VANE TYPE WATERFLOW ALARM SWITCH WITH RETARD VSR-F VANE TYPE WATERFLOW of Protection ALARM SWITCH WITH RETARD U.S. Pat. No. 3921989 Canaries Pat. No. 0009680 Other Patents Pending Potter Electric. Rd., 1990 GENERAL INFORMATION The Model VSR-F is a vane type waterfiow switch for use on wet Sprinkler systems. Ills UL Listed and FM Approved for use on sleet pipe; schedules tO through 40, sizes 2" thru 8" (.50.m thru 200mm). LPC approved sizes am 2" thru 9" (50mm thru 200mm). The unit may also be used as a sectional waterttuw detector on large systems. The unit contains two single pub, double thrum, snap action switches and an adjustable, instantly recycling pneumatic re- tard. The switches are actuated when a blow of 10 gallons per minute (38 LPM) or mom occurs downstream of the device. The flow condition must exist for a period of time necessary to overcome the selected retard period. ENCLOSURE: The unit is enclosed in a general purpose, die- cast housing. The cover is held in place with two tamper resis- tant screws which require a special key for removal. A field in- stallable cover tamper switch is am/able as an option which may be used to indicate unauthorized removal of the cover. See bulletin no. 5400775 for installation instructions of this switch. ULULCandCSFMLiued,FMandLpCgApproved,pjyMRA Accepted. CE Marked Service Pressure: Uptn450 PSI (31 BAR) MinimumPlowRateforAlarm: 100PM(381.PM) Maximum Surge: 18 FPS (5.5 ads) ConOactitatingu: Two sets of SPOT (Form C) 15.0 Amps at 125/250VAC 2.0 Amps at 3OVDC Resistive Conduit Entrances: Two knockouts provided for t/2 conduit Environmental Specifications: Suitable for indenter outdoor use with factory instated gasket and die-cast housing. NEMA 4/tP54 Rated Enclosure - use with appropriate conduit titling. Temperature Range; 40F/120"F, 4,5C/49C Non-corrosive sleeve factory installed in saddle. Caution: This device is not intended for applications in explosive environments. ttizesAvailabie: Steel Pipe schedules 10 thru 40. sizes 2(hm 8" BS 1387 pipe 50mm thru 200mm Nate; For copper or plastic pipe use Model VSR-CF. Service Use: Automatic Sprinkler NPPA-13 One ortwo family dwelling NFPA-130 Residential occupancy up to four stories NFPA-13R National Fire Alarm Code NFPA-72 Optional: CaoerTamper Switch Kit, Stuck No. 0090018 INSTALLATION: See Frg.2 These devices may be mounted on horizontal or vertical pipe. On horizontal pipe they should be installed on the top side of the pipe where they will he accessible. The units should not be in- stalled within 6" (50cm) of fitting which changes the direction of the waterltow, or within 24" (60 cm) at a valve or drain. Drain the system and drill a hole to the pipe using a circular saw in stow speed drill The 2" (50mm) and 2 1/2" (65mm) devices require a hole with a diameter 0111/4" -. 1/8" - 1/16 (33mm ±2mm). All other sizes require a hole with a diameter of 2" 61/8" (00mm *2mm). Clean the inside pipe of all growth or other material for a dis- tance equal to the pipe diameter on either side of the hole. Roll the vane so that it maybe inserted into the hole; donut bend or crease it. Insert the vane so that the arrow on the saddle points in the direction Of the waterttnw. Install the saddle strap and tighten nuts a8ematety 10 an eventual 50 04bs. (68 n-rn) of torque (see Fig. 2). The vane must not rob the inside of the pipe or bind in any way. Specifications subject to change without notice. FIG. I SWITCH TERMINAL CONNECTIONS CLAMPING PLATE TERMINNAL CAUTION: An uninsutated section of a single conductor should not be looped around the termi- nal and serve as two sops- rate connections. The wire must be severed, thereby providing supervision of the connection in the event that the wire becomes dislodged from under the terminal FIG, 2 OPT— ruorrn —CH NOT lust covre nrc FOR RETARD bARjsintrtr: TO cssncc nor TURN tutu Comm ntercvuol roe ursrem nor 00.rr. uSE trralulauu Mourn or errAnD stcossaan W PREVENT .-uc.Rus. A '0' SEIrDIG S M-1nOuuUtrry 100 flms. munson 5 SEt 10'0', C / Cover Tampur (trsith uaunr in place) rn R No I—'r we) mel Potter Electric Signal Company "2001 Cnn/gReed. St Louis, MO, 63148-4101• Phone; 800-320-3830/Conuda 000-002-1033 vmsv.p000rsignat.000, PRINTED IN050 McI. convener .OEVW PAGE 1 OF 2 MFG. 05400701.50 tnn"-wt ove000. OCReD scnrucs (10 SEts,) n-or TO TO k..w 1 FIG. 3 TYPICAL ELECTRICAL CONNECTIONS NOTES: FIG- 4 1. The Model VSR-F has two To remove knockouts; Place ow/tomes, one can be trued to screwdriver at edge of knock- station. pro- outs, not in the center. 3. For supervised circuits see Lll;TL pdtm or remote signaling "Switch Terminal Connec- tions* drawing and canton note (Ao. 1). - APPUCATION WARNING! Doe lathe possibility of unintended discharges caused by pressure surges, trapped air, or short retard times, watertlow switches that ore m00500ng wet pipe sprinkler systems should not housed as the sole initiating device to discharge AFFF, deluge, or chemical suppression systems. TESTING The frequency of inspection and testing for the model VSR-F and its associated protective monitoring system should be in accordance with applicable NFPA Codes and Standards and/or the authority having jurisdiction (manufacturer recommends quarterly or mare frequently). if provided, the inspector's test valve, that is usually located at the end of the most remote branch One, should always be used for test purposes. If there are no provisions for testing the operation of the 110w detection device on the system, application of the VSR-F is not recommended or advisable. A minimum flow of 10 gpm (38 1pm) is required to activate this device. IMPORTANT NOTICE: Please advice the person responsible for testing of the Ore protection system that this system must be tested in accordance with the testing instructions. PRINTED INUSA MKT. 0000rn0f. REV W PAGE20F2 MFG.054n0701-7/02 (E)POTTER BELLS The Symbol of Protection UL Listed - - Sizes Available: 6"(150mm),&(200mm)and 10(250mm) Voltages Available: 24VAC WT --. ' JI 12OVAC - >_-. 12VDC (10.2 to 15.6) Polarized 24VDC (20.4 to 31.2) Polarized - k - Service Use: Fire Alarm GeneralSignaling '1 . 7.1 BurgiarAlaron Environment: Indoor or outdoor use (See Note 1) -40 to 150'F (-40' to 66'C) (Outdooruse requires weatherproof Termination: 4 No. 18 AWG stranded wires 6° BELL SHOWN Finish: Red powder coating Optional: Model BBK-1 weatherproof backbox These vibrating type bells are designed for use as tim, burglar or general signaling devices. They have low power con-sumption and high decibel ratings. The unit mounts on a standard 4' (101 mm) square electrical box for indoor use or on a model BBK-1 weatherproof backbox for outdoor applications. Weatherproof backbox model BBK-1, Stock No. 1500001. ALL DC BELLS ARE POLARIZED AND HAVE BUILT-IN TRANSIENT PROTECTION: ,1c0(V I 000900 000m000 j ®POTTER BELLS The Symbol of Protection DIMENSIONS INCHES (mm) FIG. I BELLS FIG. 2 WEATHERPROOFBACKBOX BOXHASONEThREAOEO 1/2'CONDUrTENrRANCE 00) L _ 2 IVIV 000. gre-, (cool CeO. 1776-2 FIG. 3 WIRING (REAR VIEW) D.C. BELLS (OBSERVE POLARITY) A.C. BELLS iCI 01000x, eon in, eon cools . Coon 0909 50109 i, noncom vni.oslry TO TRIO Sc. 01115, 001(0 05015 50. 0(1.1.5. 1500101000 (001 (0000 *001 SO'a*flTttV a. 000 '6005 0051100 (at .ntn i_as? 09_i. 3. 01.000 6109 6(0*000 (-) a. m0-cc-ONE ocslslon IS NOT n000xoo ON Sc. 0915. DWG. #776-3 Noles- .I I ' I I Minimum dB ratings are calculated from integrated sound pressure measurements made at Underwriters Laboratories as specified in UL Standard 464. UL temperature range is -30' to 150'F (-34' to 66'C). Typical dB ratings are calculated from measurements made with a conventional sound level meter and are indicative of output levels in an actual installation. P011nrfllecsicsignulCornpany 2081 Cooig Road. Si. Louis. MO. 63146.4161- Phone: 800-325-39361C.onado 088.882.1833 00000.poitoroi0ndtcorn pasTeD in usa Mlcr.mos006l. REV o Paso i OF 2 MEG. #54011775 . 5/Os INSTALLATION The bell shall be installed in accordance with NFPA 72 or local Ahj. The lop of the device shall be no less than 60' Aff and not less than 6" below the ceiling. Removethegong. Connect wiring (see Fig. 3). Mount bell mechanism to backbox (bell mechanism must be mounted with the striker pointing down). Reinstall the gong (be sure that the gong positioning pin, in the mechanism housing, is in the hole in the gong). Test all bells for proper operation and observe that they can be heard where required (bells must be heard in all areas as designated by the authority having jurisdiction). PRINTED IN usa M. 00850001.REV 5 PAGE 2 OF 2 56.5. 054m716 .5/os Copyright 2015 Netioririt Fire Protection Association (NFPA). Lwensect, by agreement, for individual use and download on January 21. 2015 to JJJ ENTERPRISES fordnstgnated user PETE CAMEJO. No other reproduction or transmission in any form permitted without written permission of NFPA. For inquires or to report unauthorized use, contact licensingnfpa.org. DOCUMENTATION 72-37 SYSTEM RECORD OF COMPLETIOIF 1 E (F Q P This form is to be completed by the system installation contractor at the time o t cce4tpnth ark1a It shalt be permitted to modify this form as needed to provide a more c le Insert N/A in all unused lines. Attach additional sheets, data, or calculations as necessary to provide a complete record. Form Completion Date: Supplemental Pages Attached: PROPERTY INFORMATION Name of property: Daybreak Church Address: 6515 Ambrosia Ln, Carlsbad 92011 Description of property: Church Name of property representative: Address: Phone: ________________________ Fax: E-mail: INSTALLATION, SERVICE, TESTING, AND MONITORING INFORMATION Installation contractor: JJJ Enterprises Address: 115 Market street - Escondido - CA - 92029 Phone: (LP) 747-3050 Fax:_______________________ E-mail: Service organization: Same as above Address: Phone: __________ ______ Fax: ________________________ E-mail: Testing organization: same as aoove Address: Phone: _______________________ Fax: ________________________ E-mail: Effective date for test and inspection contract: Monitoring organization: A rid roes Phone: _________________________ Fax:__________________________ E-mail: Account number: 1300 8171 Phone line 1: Phone line 2: Means of transmission: Cellular Entity to which alarms are retransmitted: Phone: DOCUMENTATION On-site location of the required record documents and site-specific software: Doc box by FACP DESCRIPTION OF SYSTEM OR SERVICE This is a: J New system U Modification to existing system Permit number: NFPA 72 edition: 13 4.1 Control Unit Manufacturer: Notifier Model number: NFW100 4.2 Software and Firmware Firmware revision number: 4.3 Alarm Verification lJ This system does not incorporate alarm verification. Number of devices subject to alarm verification: Alarm verification set for _________ seconds © 2012 Nat icnal Fire Protection Association NFPA 72 (p. 1 of 3) FIGURE 7.8.2a) System Record of Completion. (SIG-FUN) p (O 1 2013 Edition 12 Copyright 2015 Nanonat Fire Protection Association (NEPA). Licensed, by agreement, for individual use and download on January 21. 2015 to JJJ ENTERPRISES for designated user PETE CAMEJO. No other reproduction or transmission in any form permitted without written permission of NEPA. For inquires or to report unauthorized use, contact ticansing@nfpa.org. 72-38 NATIONAL FIRE ALARM AND SIGNALING CODE SYSTEM RECORD OF COMPLETION (continued) SYSTEM POWER 5.1 Control Unit 5.1.1 Primary Power Input voltage of control panel: 120 VDC Control panel amps: 3 Overcurrent protection: Type: Brnnknr Amps: 20 Branch circuit disconnecting means location: sub pnl Number: 5.1.2 Secondary Power Type of secondary power: 18ah 12vdc Location, if remote from the plant: Calculated capacity of secondary power to drive the system: In standby mode (hours): 24 In alarm mode (minutes): 5 5.2 Control Unit 0 This system does not have power extender panels O Power extender panels are listed on supplementary sheet A CIRCUITS AND PATHWAYS Dual Media Separate Survivability Pathway Type Pathway Pathway Class Level Signaling Line B 0 Device Power Initiating Device Notification Appliance B Other (specify): REMOTE ANNUNCIATORS Type Location INITIATING DEVICES Addressable or Alarm or Sensing Type Quantity Conventional Supervisory - Technology Manual Pull Stations 1 _______ A_.._____ A Smoke Detectors —_1 A A Photo Duct Smoke Detectors ______ ________________________ ________________________ Phrttn Heat Detectors Gas Detectors Waterfiow Switches 1 A A Tamper Switches 1 A S © 2012 National Fire Protection Association NFPA 72 (p.2 of 3) FIGURE 7.8.2(a) Continued 40, 2013 Edition Copyright 2015 National Fire Protection Association NFPA). Licensed, by agreement, for individual use and download on January 21. 2015 to JJJ ENTERPRISES for designated user PETE CAMEJO. No other reproduction or transmission in any form permitted without written permission of NFPA. For inquires or to report unauthorized use, contact licensingisfpa.org. DOCUMENTATION 72-39 SYSTEM RECORD OF COMPLETION (continued) NOTIFICATION APPLIANCES Type Quantity Description Audible Visible 8 Combination Audible and Visible 15 SPEAKERS SYSTEM CONTROL FUNCTIONS Type Quantity Hold-Open Door Releasing Devices HVAC Shutdown ii Fire/Smoke Dampers Door Unlocking Elevator Recall Elevator Shunt Trip INTERCONNECTED SYSTEMS ) This system does not have interconnected systems. Li Interconnected systems are listed on supplementary sheet CERTIFICATION AND APPROVALS 12.1 System Installation tractor T system as ecified h in has )en installed according to all NFPA standards cited herein. Signe . ______________________________ Printed name: Jim McKinley Date: 8/17/2017 Organizati _JJJ E erprises Title: __________________________ Phone: (760) 747-3050 12.2 S em Operational Test This system as specified herein has tested according to all NFPA standards cited herein. Signed: Same as above Printed name: Date: Organization: ________________________________ Title: Phone: 12.3 Acceptance Test Date and time of acceptance test: 1/1/2016 Installing contractor representative: Jim McKinley Testing contractor representative: Jim McKinley Property re ntative: AHJ rep ent © 2012 National Fire Protection Association NFPA 72 (p.3 of 3) FIGURE 7.8.2(s) Continued 2013 Edition W. Copyright 2015 National Fire Protection Association (NFPA), Licensed, by agreement, for individual use and download on January 21, 2015 to JJJ ENTERPRISES for designated user PETE CAMEJO. No other reproduction or transmission in any form permitted without written permission or NFPA For inquires or Is report unauthorized use, contact Iicnnsing@nfpa.org. 72-40 NATIONAL FrREAI..ARM AND SIGNALING CODE EMERGENCY COMMUNICATIONS SYSTEMS SUPPLEMENTARY RECORD OF COMPLETION This form is a supplement to the System Record of Completion. It includes systems and components specific to emergency communications systems. This form is to be completed by the system installation contractor at the time of system acceptance and approval. It shall be permitted to modify this form as needed to provide a more complete and/or clear record. Insert N/A in all unused lines. Form Completion Date: Number of Supplemental Pages Attached: PROPERTY INFORMATION Name of property: Address: DESCRIPTION OF SYSTEM OR SERVICE J Fire alarm with in-building fire emergency voice alarm communication system (EVAC) 0 Mass notification system U Combination system, with the following components: U Fire alarm U EVACS U MNS U Two-way, in-building, emergency communications system U Other (specify): NFPA 72 edition: ____________ Additional description of system(s): 2.1 In-Building Fire Emergency Voice Alarm Communications System Manufacturer: Notifier Model number: first rr1mrnnd Number of single voice alarm channels: _j Number of multiple voice alarm channels: Number of speakers: 15 Number of speaker circuits: I Location of amplification and sound processing equipment: —l4ear FACP Location of paging microphone stations: Location 1: Nr FACP - Location 2: Location 3: 2.2 Mass Notification System 2.2.1 System Type: U In-building MNS-.combination U In-building MNS U Wide-area MNS U Distributed recipient MNS U Other (specify): © 2012 National Fire Protection Association NFPA 72 (p.1 of 3) FIGURE 7.8.2(b) Emergency Communications System Supplementary Record of Completion, (SIG-FUN) lill 2013 Edition Copyrrght 2015 National Fire Protection Association (NFPA). Licensed, by agreement, for individual use and download on January 21, 2015 to JJJ ENTERPRISES for designated user PETE CAMEJO. No other reproduction or transmission in any form permitted without written permission of NFPA. For inquires or to report unauthorized use, contact licensing@nfpa.org. DOCUMENTATION 72-41 EMERGENCY COMMUNICATIONS SYSTEMS SUPPLEMENTARY RECORD OF COMPLETION (continued) DESCRIPTION OF SYSTEM OR SERVICE (continued) 2.2.2 System Features: C] Combination fire alarm/MNS C] MNS autonomous control unit C] Wide-area MNS to regional national alerting interface C] Local operating console (LOC) C] Distributed-recipient MNS (DRMNS) C] Wide-area MNS to DRMNS interface U Wide-area MNS to high power speaker array (1-IPSA) interface IJ In-building MNS to wide-area MNS interface C] Other (specify): 2.2.3 MNS Local Operating Consoles Location 1: Location 2: Location 3: 2.2.4 High Power Speaker Arrays Number of HPSA speaker initiation zones: Location 1: Location 2: Location 3: 2.2.5 Mass Notification Devices Combination fire alarm/MNS visual devices: MNS-only visual devices: Textual signs: Other (describe): Supervision class: 2.2.6 Special Hazard Notification U This system does not have special suppression predischarge notification. C] MNS systems DO NOT override notification appliances required to provide special suppression predischarge notification. TWO-WAY EMERGENCY COMMUNICATIONS SYSTEMS 3.1 Telephone System Number of telephone jacks installed: Number of warden stations installed: Number of telephone handsets stored on site: Type of telephone system installed: C] Electrically powered C] Sound powered 3.2 Two-Way Radio Communications Enhancement System Percentage of area covered by two-way radio service: Critical areas % General building areas _______ Amplification component locations: Inbound signal strength Donor antenna isolation is Radio frequencies covered: Radio system monitor panel location: © 2012 National Fire Protection Association FIGURE 7.82(b) Continued dBm Outbound signal strength dBm - dB above the signal booster gain. NFPA 72 (p.2 of 3) 2013 Edition 04) Copyright 2015 National Foe Protection Association (NFPA). LiCenswt, by agreement, for individual use and download on January 21,201510 JJJ ENTERPRISES for designated user PETE CAMEJO. No other reproduction or transmission in any form permitted without written permission of NFPA. For inquires or to report unauthorized use, contact licensrngnfpa.org, 72-42 NATIONAL FIRE ALARM AND SIGNALING CODE EMERGENCY COMMUNICATIONS SYSTEMS SUPPLEMENTARY RECORD OF COMPLETION (continued) TWO-WAY EMERGENCY COMMUNICATIONS SYSTEMS (continued) 3.3 Area of Refuge (Area of Rescue Assistance) Emergency Communications Systems Number of stations: -Location of central control point: Days and hours when central control point is attended: Location of alternate control point: Days and hours when alternate control point is attended: 3.4 Elevator Emergency Communications Systems Number of elevators with stations: Location of central control point: Days and hours when central control point is attended: Location of alternate control point: Days and hours when alternate control point is attended: 3.5 Other Two-Way Communications System Describe: CONTROL FUNCTIONS This system activates the following control functions specific to emergency communications systems: Type Quantity Mass Notification Override of Alarm Signaling Systems or Appliances See Main System Record of Completion for additional information, certifications, and approvals. © 2012 National Fire Protection Association NFPA 72 (p.3 of 3) FIGURE 7.8.2(b) Continued 2013 Edition Copyright 2015 National Fire Protection Association (NFPA). Licensed, by agreement, for individual use and download on January 21. 2015 to JJJ ENTERPRISES for designated user PETE CAMEJO. No other reproduction or transmission in any form permitted without written permission of NFPA. For inquires or to report unauthorized use, contact licensingtnfpa.org. DOCUMENTATION 72-39 SYSTEM RECORD OF COMPLETION (continued) NOTIFICATION APPLIANCES Type Quantity Description Audible Visible 8 Combination Audible and Visible 15 SPFAKERS SYSTEM CONTROL FUNCTIONS Type Quantity Hold-Open Door Releasing Devices HVAC Shutdown 11 Fire/Smoke Dampers Door Unlocking Elevator Recall Elevator Shunt Trip INTERCONNECTED SYSTEMS )ü This system does not have interconnected systems. Li Interconnected systems are listed on supplementary sheet CERTIFICATION AND APPROVALS 12.1 System Installation Contractor This system as specified herein has been installed according to all NFPA standards cited herein. Signed: _________________________________ Printed name: Jim McKinley Date: 8/17/2017 Organization:. fl!SPnises Title: Phone: (760) 747-3050 12.2 System Operational Test This system as specified herein has tested according to all NFPA standards cited herein. Signed: Same as above Printed name: Date: Organization:......... Title: Phone: 12.3 Acceptance Test Date and time of acceptance test: Installing contractor representative: Jim McKinley Testing contractor representative: Jim McKinley Property representativ AHJ representati . © 2012 National Fire Protection Association NFPA 72 (p.3 of 3) FIGURE 7.8.2(a) Continued 2013 Edifiort I 2 3 '1 5 6 7 8 9 ic 11 12 13 iLl 15 16 17 18 19 2C 21 22 23 24 25 26 27 CIRCUIT 1300 ACCOUNT 8171 ZONE TYPE SIGNAL DESCRIPTION 1 Smoke Alarm FACP Room 160 Pull Station Alarm Lobby 161 Relay Trbl HVAC Unit #9 Shut Dn 162 Duct Det Supv HVAC Unit #9 163 Relay Trbl HVAC Unit #8 Shut Dn 164 Duct Det Supv HVAC Unit #8 165 Relay Trbl HVAC Unit #7 Shut Dn 166 Duct Det Supv HVAC Unit #7 167 Relay Trbl HVAC Unit #10 Shut Dn 168 Duct Det Supv HVAC Unit #10 169 Relay Trbl HVAC Unit #4 Shut Dn 170 Duct Det Supv HVAC Unit #4 171 Relay Trbl HVAC Unit #11 Shut Dn 172 Duct Det Supv HVAC Unit #11 173 Relay Trbl HVAC Unit #2 Shut Dn 174 Duct Det Supv HVAC Unit #2 175 Relay Trbl HVAC Unit #1 Shut Dn 176 Duct Det Supv HVAC Unit #1 177 Relay Trbl HVAC Unit #5 Shut Dn 178 Duct Det Supv HVAC Unit #5 179 Spare 180 Relay Trbl Sound System Shut Dn 181 Relay Trbl HVAC Unit #3 Shut Dn 182 Duct Det Supv HVAC Unit #3 183 Relay Trbl HVAC Unit #6 Shut Dn 184 Duct Det Supv HVAC Unit #6 185 Tamper Supv OS&Y Check valve 186 lWaterflow jAlarm I Mian WF switch