Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
1 LEGOLAND DR; ; FPC2018-0045; Permit
PER]ET REPORT tcity of Carlsbad Print Date: 12/02/2020 Permit No: FPC2018-0045 Job Address: 1 LEGOLAND DR, CARLSBAD, CA 92008-4610 Status: Closed - Finaled Permit Type: FIRE-Construction Commercial Work Class: Fire Sprinklers Parcel #: 2111000900 Track #: Applied: 02/08/2018 Valuation: $120,000.00 Lot #: Issued: 02/20/2018 Occupancy Group: Project #: DEV2016-0028 Finaled Close Out: 12/02/2020 #of Dwelling Units: Plan #: Bedrooms: Construction Type: Bathrooms: Orig. Plan Check #: Inspector: Plan Check #: Final Inspection: Project Title: LEGOLAN D WP17 WATER SLIDE Description: LEGOLAND WP17 / WATERSLIDE RESTROOM -SPRINKLER <100 (19 HEADS) Applicant: FPContractor: TITAN FIRE PROTECTION INC TITAN FIRE PROTECTION INC CHRISTIAN MCGREGOR 1341 DISTRIBUTION WAY, # STE 14 1341 DISTRIBUTION WAY, # STE 14 VISTA, CA 92081-8843 VISTA, CA 92081-8843 (760) 295-3436 (760) 295-3436 FEE AMOUNT FIRE NFPA 13 System < 100 heads $601.00 FIRE Reinspection (per inspection) $187.00 FIRE Reinspection (per inspection) $187.00 Total Fees: $975.00 Total Payments To Date: $975.00 Balance Due: $0.00 Fire Department Page 1 of 1 1635 Faraday Avenue, Carlsbad CA 92008-7314 1 760-602-4665 1 760-602-8561 f I www.carlsbadca.gov 01TAN FIRE PROTECTION Fire Protection Contractor - License #989280 FIRE SUPRESSION HYDRAULIC CALCULATION LEGOLAND WPI7 WATER SLIDE RESTOOMS I LEGOLAND DRIVE CARLSBAD, CA 92008 CONTRACT NO. 18036 RECEJ\IED FEB 08 2018 CARLS bAt) FIRE DEPARTMENT 2880 Scott Street, Suite 105- Vista, CA 92081 760-295-3881 - phone - 760-295-3437 - fax www.titanfpinc.com Page CARLSBAD FIRE DEPARTMENT Fire Prevention Division 1635 Faraday Avenue - Carlsbad, CA 92008 760.602.4665 WATER AVAILABILITY FORM SECTION A: TO BE COMPLETED BY CUSTOMER PROJECT NAME: Legoland SR#: (Assigned upon plan submittal) PROJECT ADDRESS: Legoland CITY: Carlsbad PHONE: (760) 484.3220 (Commercial Development Resources) FAX NUMBER: (949) 610.8997 Largest Building (ft. 2): Sprinkled? Construction Type: SECTION B: TO BE COMPLETED BY LOCAL WATER COMPANY. CUSTOMER TO PROVIDE RESULTS TO CFD. Water Purveyor: City of Carlsbad Location of test (reference map required): Internal northern site TEST INFORMATION IS VALID FOR 6 MONTHS FROM DATE PERFORMED Flow Test Results Static pressure: 92 PSI Hydrant Number (if applicable): NA (node J18) Elevation of test: 169(est)Feet Date/Time of Test': Pitot Tube Reading: PSI Corresponding Flow: GPM Total Flow: 3,630 GPM Residual Pressure 20 PSI At peak demand, this water system is capable of providing a fire flow discharge at 20 psi of 3,630 gpm. 'Test to be performed as close as possible to the time the most conservative flows and pressures are expected. Note: If the water availability information was obtained in a manner other than a flow test (i.e. computer modeling), fill out the information above as applicable and check here: x Name: Jennifer R. Mael, P.E. Eng. Lic. No. (if applicable):C69606 Signature:__________________________________________ 61/ Title/Org:Pct Manager Date: 03/01/2017 Internal LeoIand Fire Flow Analysis A 18 - SLIF11, "il~ EFiE li \\: 8' \ 8" 10" Prepared By: Jennifer R. Mael, P.E. - MCS - (EXISTING) FOR REFERENCE ONLY SPECIFICATION SUBMITTAL SHEET V.ILIONS II FEATURES Sizes: U 2 1/2 U 3" U 4" U 6° U 8' U 10' Maximum working water pressure 175 PSI Maximum working water temperature 140°F Hydrostatic test pressure 350 PSI End connections (Grooved for steel pipe) AWNA C606 (Flanged) ANSI B16.1 Class 125 OPTIONS (Suffixes can be combined) U - with NRS shut-off valves (standard) U FS - with cast iron wye type strainer (flanged only) U FSC - with epoxy coated wye type strainer (flanged only) U G - with grooved end NRS gate valves U GF - with grooved inlet gate connection and flanged outlet gate connection U FG - with flanged inlet gate connection and grooved outlet gate connection U L - less shut-off valves (flanged body connections) U MS - with Integral Relief Valve Monitor Switch U OSY - with OS&Y gate valves U P1 - with Post Indicator gate valve (3"- 10) ACCESSORIES U Repair kit (rubber only) U Thermal expansion tank (Model XT) U OS & Y Gate valve tamper switch (OSY-40) U Air gap (Model AG) U Electronic Solenoid Timer (Model EST) U QT-SET Quick Test Fitting Set U Test Cock Lock (Model TCL24) APPLICATION Designed for installation on potable water lines to protect against both backsiphonage and backpressure of contaminated water into the potable water supply. The Model 375 provides protection where a potential health hazard exists. Ideal for use where lead-free* valves are required STANDARDS COMPLIANCE (Unless otherwise noted, sizes 2 112" thru 10") ASSE® Listed 1013 IAPMO® Listed CSA® Certified (2 1/2" thru 8") AWtNA Compliant C511 FM® Approved UL® Classified C-UL® Classified NYC MEA49-01-M Vol 2 Approved by the Foundation for Cross Connection Control and Hydraulic Research at the University of Southern California. NSF® Listed-Standard 61, Annex G* *(025% MAX. WEIGHTED AVERAGE LEAD CONTENT) MATERIALS Main valve body Ductile Iron ASTM A 536 Grade 4 Access covers Ductile Iron ASTM A 536 Grade 4 Coatings FDA Approved fusion epoxy finish Internals Stainless steel. 300 Series NORYLTM, NSF Listed Fasteners Stainless Steel, 300 Series Seal rings EPDM (FDA approved) 0-rings Buna Nitrile (FDA approved) Springs Stainless Steel, 300 Series Sensing line Stainless Steel, braided hose Relief Valve discharge port: 2 1/2" -6" - 2.75 sq. in. 8" - 10" - 3.69 sq. in. Attention: Model 375 (flange body) and Model 375A (grooved body) have different lay lenaths. DIMENSIONS & WEIGHTS (do not include pkg.) DIMENSION (approximate) WEIGHT MODEL 375 B LESS E OS&Y E E WTHOJT WITH WITH SIZE A GATE c D OPEN OS&Y NRS F G H GATE NRS GATE VALVES CLOSED GATE VALVES VALVES VALVES in. Imm in. I mm in. Imm in. mm in. Imm in. mm in. Imm in. Imm in. mm in. Imm in. mm lbs. jj lbs. kg lbs. I kg 2 V21 65 1 31 1787 157/8 403 71/4 184 3 3/4195 16 3/8 416 137/81352 Il 3/8 289 91/2 241 83/8 213 41 1/4 1048 60 27.2 162 73.5 170 77.2 3 80 32 813 157/8 403 71/4 18433/4 95 187/ 479 15 5/8 397 12 3/8 314 91/2 24 83/8 213 42 3/4 1086 60 27.2 184 83.5 190 86.3 T 100375/8956191/2495 8 2034 1/211141223/ 578 181/4464i43/4 75 11 27991/4 '.35523/4134098 44.5 ~78I26."288 13l1' 6 150144 3/4 1137 231/2 597 10 254 6 11521301/8 765 233/4 603 19 483123/8314 103/4 273 623/4 1594 175 795 459 2084475 215.6 8 200 603/4 1543 373/4 959 11 279 10 254 7 3/4 959 29 1/4 74 22 1/2 512 5 3/839 163/4. 426 85 2159 377 171 829 .376.4 853 387.S 10 250163 3LI 1619 373/4 959 11 279 10 254 53/4 1162 353/8 899 26 1/2 613 153/839 163/4 426 93 1/4 2369 407 185 116 530 1225 556 iI*lj 'AF1[s]I of 2 WILKINS a Zurn company, 1747 Commerce Way, Paso Robles, CA 93446 Phone:805/238-7100 Fax:805/238-5766 In Canada: ZURN INDUSTRIES LIMITED, 3544 Nashua Dr., Mississauga, Ontario L4V 11_2 Phone:9051405-8272 Fax:905/405-1292 Product Support Help Line: 1-877-BACKFLOW (1-877-222-5356) Website: http://www.zurn.com FLOW CHARACTERISTICS MODEL 3752 1/2", 3" & 4" (STANDARD & METRIC) FLOW RATES (us) 12.6 25.2 37.9 0 200 400 600 FLOW RATES (GPM) 50.5 138 u (I) 0 Iu'+ —J 69 0) ') 0) J W 0 ° 800 252.4 138 u (/) 0 104 —J 69 35 0°- 4000 •• — I ___:i:- - = °- 0 0 1000 2000 3000 FLOW RATES (GPM) GRated Flow (Established by approval agencies) TYPICAL INSTALLATION Local codes shall govern installation requirements. Unless otherwise specified, the assembly shall be mounted at a minimum of 12" (305mm) and a maximum of 30" (762mm) above adequate drains with sufficient side clearance for testing and maintenance. The installation shall be made so that no part of the unit can be submerged. DIRECTION OF FLOW CD INDOOR INSTALLATION (375GF) Capacity thru Schedule 40 Pipe (GPM) Pipe size 5 ft/sec 7.5 ft/sec 10 ft/sec 15 ft/sec 21/2' 75 112 149 224 115 173 230 346 198 298 397 595 6" 450 675 900 1351 8" 780 1169 1559 2339 10" 1229 1843 2458 3687 12" 1763 2644 3525 5288 -------------------- I PROTECTIVE I OUTDOOR INSTALLATION SPECIFICATIONS The Reduced Pressure Principle Backflow Prevention Assembly shall be ASSE® Listed 1013, and supplied with full port gate valves. The main body and access cover shall be epoxy coated ductile iron (ASTM A 536 Grade 4), the seat ring and check valve shall be NORYLTM, the stem shall be stainless steel (ASTM A 276) and the seat disc elastomers shall be EPDM. The checks and the relief valve shall be accessible for maintenance without removing the device from the line. The Reduced Pressure Principle Backflow Prevention Assembly shall be a WILKINS Model 375. WILKINS a Zurn company, 1747 Commerce Way, Paso Robles, CA 93446 Phone:805/238-7100 Fax:805/238.5766 IN CANADA: ZURN INDUSTRIES LIMITED, 3544 Nashua Dr., Mississauga, Ontario L4V 11-2 Phone:905/405-8272 Fax:905/405-1292 Product Support Help Line: 1-877-BACKFLOW (1-877-222-5356) • Website: http://www.zurn.com Page 2 of 2 - Fire Protection by Computer Design TITAN FIRE PROTECTION, INC. 2880 SCOTT ST. SUITE 105 VISTA, CA. 92081 760.295.3437 Job Name : LEGOLAND RESTROOMS Building : FP2 Location : I LEGOLAND DRIVE System : Area 1 Contract : 18036 Data File : Legoland Restrooms Calc.WXF Computer Programs by Hydratec Inc. Route 111 Windham N.H. USA 03087 TITAN FIRE PROTECTION, INC. Page 1 LEGOLAND RESTROOMS Date 1-25-18 HYDRAULIC CALCULATIONS for Project name: LEGOLAND RESTOOMS Location: I LEGOLAND DRIVE Drawing no: FP2 Date: 1-26-18 Design Remote area number: Area 1 Remote area location: RESTROOMS Occupancy classification: LH & OH 2 Density: .1 & .2 - Gpm/SqFt Area of application: 862 - SqFt Coverage per sprinkler: VARIES - SqFt Type of sprinklers calculated: SSP, SSU & HSW K11.2, K8, K5.6 No. of sprinklers calculated: 10 In-rack demand: N/A - GPM Hose streams: 250 - GPM Total water required (including hose streams): 571.93 -GPM @ 61.07 - Psi Type of system: WET Volume of dry or preaction system: N/A - Gal Water supply information Date: 3-1-17 Location: SEE PLAN Source: CARLSBAD FIRE DEPARTMENT Name of contractor: Address: Phone number: Name of designer: M. Marron Authority having jurisdiction: City of Carlsbad Notes: (Include peaking information or gridded systems here.) Computer Programs by Hydratec Inc. Route 111 Windham N.H. USA 03087 Water Supply Curve C TITAN FIRE PROTECTION, INC. Page 2 LEGOLAND RESTROOMS Date 1-25-18 City Water Supply: Demand: Cl - Static Pressure : 82.8 Dl - Elevation : 3.465 C2 - Residual Pressure: 18 D2 - System Flow :321.934 C2 - Residual Flow : 3630 D2 - System Pressure : 61.078 Hose ( Demand ) :250 D3 - System Demand :571.934 Safety Margin : 19.600 150 140 130 p120 R° E10° S90 S Qn U 70 D2 R 60 E 50 40 30 20 10 400 800 1200 1600 2000 2400 2800 3200 3600 FLOW ( N " 1.85) Computer Programs by F-lydratec Inc. Route 111 Windham N.H. USA 03087 Fittings Used Summary TITAN FIRE PROTECTION, INC. Page 3 LEGOLAND RESTROOMS Date 1-25-18 Fitting Legend Abbrev. Name ½ f. 1 11/4 11/2 2 21/2 3 31/2 4 5 6 8 10 12 14 16 18 20 24 B NFPA 13 Butterfly Valve 0 0 0 0 0 6 7 10 0 12 9 10 12 19 21 0 0 0 0 0 E NFPA 13 90 Standard Elbow 1 2 2 3 4 5 6 7 8 10 12 14 18 22 27 35 40 45 50 61 G NFPA 13 Gate Valve 0 0 0 0 0 1 1 I I 2 2 3 4 5 6 7 8 10 ii 13 H 45 Grvd-Vic Elbow #11 0 0 I 1.5 2 2 3 3 3.5 3.5 4.5 5 6.5 8.5 10 18 20 23 25 30 S NFPA 13 Swing Check 0 0 5 7 9 11 14 16 19 22 27 32 45 55 65 I NFPA 139OFlowthruTee 3 4 5 6 8 10 12 15 17 20 25 30 35 50 60 71 81 91 101 121 Zie Wilkins 375 Filling generates a Fixed Loss Based on Flow Units Summary Diameter Units Inches Length Units Feet Flow Units US Gallons per Minute Pressure Units Pounds per Square Inch Note: Fitting Legend provides equivalent pipe lengths for fittings types of various diameters. Equivalent lengths shown are standard for actual diameters of Sched 40 pipe and CFactors of 120 except as noted with The fittings marked with a * show equivalent lengths values supplied by manufacturers based on specific pipe diameters and CFactors and they require no adjustment. All values for fittings not marked with a * will be adjusted in the calculation for CFactors of other than 120 and diameters other than Sched 40 per NFPA. The diameter modification was turned off by the operator when the job was calculated. Computer Programs by Hydratec Inc. Route 111 Windham N.H. USA 03087 Pressure / Flow Summary - STANDARD TITAN FIRE PROTECTION, INC. Page 4 LEGOLAND RESTROOMS Date 1-25-18 Node Elevation K-Fact Pt Pn Flow Density Area Press No. Actual Actual Rea. Si 8.0 11.2 12.8 na 40.07 0.1 400 12.8 Ti 9.5 16.47 na S2 8.0 11.2 13.01 na 40.4 0.1 400 12.8 T2 9.5 16.74 na S3 9.0 5.6 17.72 na 23.57 0.1 225 7.0 S4 9.5 5.6 17.82 na 23.64 0.15 130 7.0 S5 9.5 5.6 18.28 na 23.94 0.15 130 7.0 S7 8.0 5.6 17.42 na 23.38 0.1 225 7.0 T7 9.5 19.48 na S8 8.0 11.2 15.12 na 43.55 0.1 400 12.8 T8 9.5 19.57 na S9 8.0 11.2 18.21 na 47.79 0.1 400 12.8 T9 9.5 23.62 na 510 8.0 7 18.08 na 29.76 0.1 225 7.0 9.5 18.02 na 2 9.5 19.04 na 3 9.5 20.15 na S6 9.5 5.6 21.28 na 25.83 0.15 130 7.0 Ti0 9.5 21.66 na 4 9.5 25.74 na TOR 9.5 36.73 na BOR 0.5 50.58 na Cl -4.0 54.07 na C2 -4.0 54.47 na BF1 -4.0 54.55 na BF2 0.0 60.77 na SRC 0.0 61.08 na 250.0 The maximum velocity is 28.27 and it occurs in the pipe between nodes 4 and TOR Computer Programs by Hydratec Inc. Route 111 Windham N.H. USA 03087 Final Calculations - Hazen-Williams TITAN FIRE PROTECTION, INC. Page 5 LEGOLAND RESTROOMS Date 1-25-18 Hyd. Qa Dia. Fitting Pipe Pt Pt Ref. ..C.'or Ftngs Pe Pv ******* Notes Point Qt Pf/Ft Eqv. Ln. Total Pf Pn SI 40.07 1.049 E 2.0 2.170 12.800 KFactor= 11.20 to 120.0 T 5.0 7.000 -0.650 TI 40.07 0.4707 0.0 9.170 4.316 Vel = 14.88 Tl 0.0 1.442 T 6.0 9.500 16.466 to 120.0 0.0 6.000 0.0 I 40.07 0.0999 0.0 15.500 1.549 Vel = 7.87 0.0 40.07 18.015 KFactor= 9.44 S2 40.40 1.049 E 2.0 2.170 13.011 K Factor = 11.20 to 120.0 T 5.0 7.000 -0.650 T2 40.4 0.4779 0.0 9.170 4.382 Vel = 15.00 T2 0.0 1.442 T 6.0 6.540 16.743 to 120.0 0.0 6.000 0.0 1 40.4 0.1014 0.0 12.540 1.272 Vel = 7.94 0.0 40.40 18.015 K Factor = 9.52 S3 23.57 1.049 E 2.0 1.750 17.718 K Factor= 5.60 to 120.0 T 5.0 7.000 -0.217 2 23.57 0.1763 0.0 8.750 1.543 Vel = 8.75 0.0 23.57 19.044 K Factor = 5.40 S4 23.64 1.38 0.0 10.000 17.816 K Factor = 5.60 to 120.0 0.0 0.0 0.0 S5 23.64 0.0467 0.0 10.000 0.467 Vel = 5.07 S5 23.94 1.38 T 6.0 5.000 18.283 K Factor = 5.60 to 120.0 0.0 6.000 0.0 3 47.58 0.1701 0.0 11.000 1.871 Vel = 10.21 0.0 47.58 20.154 KFactor= 10.60 S7 23.38 1.049 E 2.0 8.580 17.424 K Factor =5.60 to 120.0 T 5.0 7.000 -0.650 T7 23.38 0.1737 0.0 15.580 2.706 Vel = 8.68 T7 28.09 1.442 0.0 0.580 19.480 to 120.0 0.0 0.0 0.0 T8 51.47 0.1586 0.0 0.580 0.092 Vel = 10.11 0.0 51.47 19.572 KFactor= 11.63 S8 43.55 1.049 E 2.0 2.290 15.121 KFactor= 11.20 to 120.0 T 5.0 7.000 -0.650 T8 43.55 0.5491 0.0 9.290 5.101 Vel = 16.17 T8 51.47 1.442 T 6.0 6.500 19.572 to 120.0 0.0 6.000 0.0 4 95.02 0.4937 0.0 12.500 6.171 Vel = 18.67 0.0 95.02 25.743 K Factor= 18.73 S9 47.79 1.049 E 2.0 2.290 18.208 KFactor= 11.20 to 120.0 T 5.0 7.000 -0.650 T9 47.79 0.6520 0.0 9.290 6.057 Vel = 17.74 Computer Programs by Hydratec Inc. Route 111 Windham N.H. USA 03087 Final Calculations - Hazen-Williams TITAN FIRE PROTECTION, INC. Page 6 LEGOLAND RESTROOMS Date 1-25-18 Hyd. Qa Dia. Fitting Pipe Pt Pt Ref. "C' or Ftng's Fe Pv Notes Point Qt Pf/Ft Eqv. Ln. Total Pf Pn T9 0.0 1.442 T 6.0 9.370 23.615 to 120.0 0.0 6.000 0.0 4 47.79 0.1385 0.0 15.370 2.128 Vel = 9.39 0.0 47.79 25.743 K Factor = 9.42 SIO 29.76 1.049 E 2.0 8.580 18.078 K Factor = 7.00 to 120.0 T 5.0 7.000 -0.650 TIO 29.76 0.2715 0.0 15.580 4.230 Vel = 11.05 0.0 29.76 21.658 KFactor= 6.39 1 80.47 1.682 0.0 6.000 18.015 to 120.0 0.0 0.0 0.0 2 80.47 0.1715 0.0 6.000 1.029 Vel= 11.62 2 23.57 1.682 0.0 1.580 19.044 to 120.0 0.0 0.0 0.0 T7 104.04 0.2759 0.0 1.580 0.436 Vel = 15.02 T7 -28.09 1.682 0.0 4.370 19.480 to 120.0 0.0 0.0 0.0 3 75.95 0.1542 0.0 4.370 0.674 Vel = 10.97 3 47.58 1.682 0.0 2.960 20.154 to 120.0 0.0 0.0 0.0 S6 123.53 0.3791 0.0 2.960 1.122 Vel = 17.84 S6 25.83 1.682 0.0 0.710 21.276 KFactor= 5.60 to 120.0 0.0 0.0 0.0 T10 149.36 0.5380 0.0 0.710 0.382 Vel = 21.57 TIO 29.76 1.682 0.0 5.420 21.658 to 120.0 0.0 0.0 0.0 4 179.12 0.7537 0.0 5.420 4.085 Vel = 25.86 4 142.81 2.157 2E 10.0 6.540 25.743 to 120.0 0.0 10.000 0.0 TOR 321.93 0.6640 0.0 16.540 10.983 Vel = 28.27 TOR 0.0 2.157 B 6.0 9.000 36.726 to 120.0 0.0 6.000 3.898 BOR 321.93 0.6640 0.0 15.000 9.960 Vel = 28.27 BOR 0.0 5.86 6H 45.332 255.000 50.584 to 150.0 3E 63.465 199.461 1.949 Cl 321.93 0.0034 2T 90.664 454.461 1.537 Vel = 3.83 Cl 0.0 6.16 4E 74.48 14.500 54.070 to 140.0 S 42.56 117.040 0.0 C2 321.93 0.0030 0.0 131.540 0.396 Vel = 3.47 C2 0.0 5.86 E 21.155 2.830 54.466 to 150.0 0.0 21.155 0.0 BFI 321.93 0.0034 0.0 23.985 0.081 Vel = 3.83 BF1 0.0 6.16 4E 74.48 14.000 54.547 to 140.0 Zie 0.0 74.480 5.960 * * Fixed Loss = 7.693 BF2 321.93 0.0030 0.0 88.480 0.267 Vel = 3.47 BF2 0.0 5.86 G 4.533 40.000 60.774 to 150.0 T 45.332 49.865 0.0 SRC 321.93 0.0034 0.0 89.865 0.304 Vel = 3.83 Computer Programs by Hydratec Inc. Route 111 Windham N.H. USA 03087 Final Calculations - Hazen-Williams TITAN FIRE PROTECTION, INC. Page 7 LEGOLAND RESTROOMS Date 1-25-18 Hyd. Qa Dia. Fitting Pipe Pt Pt Ref. "C' or Ftng's Pe Pv ******* Notes Point Qt Pf/Ft Eqv. Ln. Total Pf Pn 250.00 Qa = 250.00 571.93 61.078 KFactor= 73.18 Computer Programs by Hydratec Inc. Route 111 Windham N.H. USA 03087 ~-:~ ~l W~~- - ""2 A IFAN FIRE PROTECTION Fire Protection Contractor - License #989280 FIRE SUPRESSION MATERIAL SUBMITTAL LEGOLAND WPI7 WATER SLIDE RESTOOMS I LEGOLAND DRIVE CARLSBAD, CA 92008 CONTRACT NO. 18036 RECEIVED FEB 0 8 2018 CARtS SAL FIRE DEPARTMENT 2880 Scott Street, Suite 105- Vista, CA 92081 760-295-3881 - phone - 760-295-3437 - fax www.titanfpinc.com Page A IITA14 FIRE PROTECTION Fire Protection Contractor - License #989280 TABLE OF CONTENTS SPRINKLERS OVERHEAD PIPE AND FITTINGS HANGERS AND SEISMIC ALARM DEVICES VALVES OTHER 2880 Scott Street, Suite 105- Vista, CA 92081 760-295-3881 - phone - 760-295-3437-- fax ww'.titanfpinc.com Page Adjustable Concealed Standard Spray Pendent Standard and Quick Response V3807 STANDARD RESPONSE V3808 QUICK RESPONSE This concealed, designer style sprinkler allows up to 1/2713 mm adjustment to accommodate concealment needs. The standard" design provides a consistent hemispherical spray pattern. The separate two-piece mounting cup/cover plate allows easy installation and testing prior to ceiling installation. It also permits removal of suspended ceiling panels without system shut- down. The design incorporates state-of-the-art, heat responsive, frangible glass bulb design (standard or quick response) for prompt, precise operation. This sprinkler is available in various temperature ratings (see chart on page 2) and finishes to meet many design requirements. V3807 AND V3808 SPRINKLER OPERATION: The operating mechanism is a frangible glass bulb which contains a heat responsive liquid. During a fire, the ambient temperature rises causing the liquid in the bulb to expand. When the ambient temperature reaches the rated temperature of the sprinkler, the bulb shatters. As a result, the water- way is cleared of all sealing parts and water is discharged towards the deflector. The deflector is designed to distribute the water in a pattern that is most effective in controlling the fire. COVERAGE: For coverage area and sprinkler placement, refer to NFPA 13 standards. TECHNICAL SPECIFICATIONS: Exaggerated for clarity JOB/OWNER System No. Location Models: V3807, V3808 Style: Adjustable concealed, ordinary hazard, light hazard Nominal Orifice Size: 1/2'/13mm K-Factor: 5.61mp./8.1S.1/' Nominal Thread Size: 1/2'/15mm Max. Working Pressure: 300psi/2068kPa Factory Hydrostatic Test: 100% @600 psi! 4140 kPa Mm. Operating Pressure: 7p5i!48kPa Temperature Rating: See chart on page 2. MATERIAL SPECIFICATIONS Deflector: Bronze per UNS C22000 Cover Plate: Fusible solder Bulb: Glass with glycerin solution. Bulb Nominal Diameter: Standard: 5,0 mm Quick Response: 3,0 mm Load Screw: Bronze per UNS C65100 Pip Cap: Bronze per UNS C65100 Spring: Stainless steel per UNS S30100 Seal: Teflon* tape Frame: Die cast brass 65-30 Pins: Stainless steel per UNS S30400 Cup: Cold rolled steel, zinc chrome plated Cover/Escutcheon: Brass per UNS C26000 Lodgement Spring: Stainless steel per UNS S30200 Protective Cap: Polyethylene CONTRACTOR Submitted By ACCESSORIES Installation Wrench: Concealed: V38-4 or V38-5 Sprinkler Finishes: Plain brass (only) Cover Finishes: Chrome plated White painted Flat black Custom painted A For K-Factor when pressure is measured in Bar, multiply S.I. units by 10.0. * Teflon is a registered trademark of Dupont Co. ENGINEER Spec Sect Para Date Approved www.victaulic.com VICTAULIC IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. 0 2009 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REV_A %tauIicf 40.55_i FIRE PROTECTION PRODUCTS AUTOMATIC SPRINKLERS 40.55 V38, K56 300 psi/2068 kPa High Pressure Adjustable Concealed Standard Spray Pendent Standard and Quick Response V3807 STANDARD RESPONSE V3808 QUICK RESPONSE APPROVALSILISTINGS - Orifice Size (inches) Orifice Size (mm) 13 13 Nominal K Factor Imperial 5.6 Nominal K Factor S.I. 8.1 8.1 - Standard Quick Response 5mm bulb 3mm bulb Deflector Type Concealed Concealed Pendent Pendent Adjustment fl TemperatureApproved 1350F/570C 135°F/57°C 155°F/68°C 1550F/680C cULus 175°F/79°C 1750F/790C 2000F/930c 200°F/93°C b Listings and Approvals as of printing. All are approved open, except for areas designated For K Factor when pressure is measured in Bar, multiply S.I. units by 10.0 www.victaulic.com 'JBtaUIId VIcTAuLIc IS REGISTERED TRADEMARK OF VICTAULIC COMPANY © 2009 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 40.55_2 REVA FIRE PROTECTION PRODUCTS - AUTOMATIC SPRINKLERS 40.55 V38, K5.6 300 psi/2068 kPa High Pressure Adjustable Concealed Standard Spray Pendent Standard and Quick Response V3807 STANDARD RESPONSE V3808 QUICK RESPONSE RATINGS All glass bulbs are rated for temperatures from -67°F/-55°c to those shown in table below __________ Ordinary A I4__L 135 Lll 100 Oran57 It t! 38 ge Ir.l1wTjsII A' I 135 Ih1i 100 57 38 Ordinary c 155 loo j Red 0* 38 165 150 68 74 65 Intermediate S 175 iSO Yellow 79 65 Intermediate j I 200 10 93 65 Green A For use with Standard or Quick Response concealed Sprinkler 135°F/57C or 155F/68c. 4 D For use with Standard or Quick Response concealed Sprinkler l75F/79°C or 200F/93C Custom Finish - customer to provide paint specification, allow 4-6 weeks for samples. ORDERING INFORMATION Please specify the following when ordering: Sprinkler Model Number Style Temperature Rating K-Factor Thread Size Quantity Cover Finish Wrench Model Number WARNING A WARNING Proper temperature rated cover must be used with the correct sprinkler rating per the Temperature Chart Ratings. The plastic shipping cap must be removed for the sprinkler to operate properly. If shipping cap is replaced over an installed sprinkler for purposes of painting or plaster- ing, then the fire protection system shall be considered out of service, the Authority Having Jurisdiction notified, and a firewatch is suggested. Failure to do so may result in failure of sprinkler to operate causing serious personal injury or property damage. www.victaulic.com \,4tauIict VICTAULIC IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2009 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REV_A 40.553 FIRE PROTECTION PRODUCTS - AUTOMATIC SPRINKLERS V38, K5.6 300 psi/2068 kPa High Pressure Adjustable Concealed Standard Spray Pendent Standard and Quick Response V3807 STANDARD RESPONSE V3808 QUICK RESPONSE 40.55 WARNING A WARNING Always read and understand installation, care, and maintenance instructions, supplied with each box of sprinklers, before proceeding with installation of any sprinklers. Always wear safety glasses and foot protection. Depressurize and drain the piping system before attempting to install, remove, or adjust any Victaulic piping products. Installation rules, especially those governing obstruction, must be strictly followed. Painting, plating, or any re-coating of sprinklers (other than that sup- plied by Victaulic) is not allowed. Failure to follow these instructions could result in serious personal injury and/or property damage. The owner is responsible for maintaining the fire protection system and devices in proper operating condition. For minimum maintenance and inspection requirements, refer to the current National Fire Protection Association pamphlet that describes care and maintenance of sprinkler systems. In addition, the authority having jurisdiction may have addi- tional maintenance, testing, and inspection requirements that must be WE e followed. Li If you need additional copies of this publication, or if you have any questions about the safe installation of this product, contact Victaulic World Headquarters: P.O. Box 31, Easton, Pennsylvania 18044-0031 USA, Telephone: 001-610-559-3300. www.victaulic.com 1#tauIic" VIcTAuLIc IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. 02009 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 40.55_4 REV_A DIMENSIONS Models V3807, V3808 (drawings not to scale) 2O4/68 mm E Max. Hole 23/8"/60 mm Mm. Hole ii 2M'/59 mm 1½/38 mm MINIMUM EXTENSION Finished Surface 2/51 mm ½/13 mm Adjustment FIRE PROTECTION PRODUCTS - AUTOMATIC SPRINKLERS 40.55 V38, K56 300 psi/2068 kPa High Pressure Adjustable Concealed Standard Spray Pendent Standard and Quick Response V3807 STANDARD RESPONSE V3808 QUICK RESPONSE Finished Surface MAXIMUM EXTENSION AVAILABLE WRENCHES Concealed Pendent -. V3807. V3808 V38-4 or V38-5 www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2009 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REV_A \4taulicr 40.55_5 FIRE PROTECTION PRODUCTS - AUTOMATIC SPRINKLERS V38, K5.6 300 psi/2068 kPa High Pressure Adjustable Concealed Standard Spray Pendent Standard and Quick Response V3807 STANDARD RESPONSE V3808 QUICK RESPONSE DISTRIBUTION PATTERNS Models V3807, V3808 K5.6 standard concealed pendent distribution patterns - trajectory 40.55 3.0 m 8' 2.4m l.8m 4, 1.2m 0.6rn 0 2' 4' 6' 8' 10' 12' 14' 0.6m 1.2m 1.8m 2.4m 3.0m 3.7m 43m 7ps1 lspsi 30 psi 48kPa 103kPa 207kPa NOTES: 1 Data shown is approximate and can vary due to differences in installation. 2 These graphs illustrate approximate trajectories, floor-wetting, and wall-wetting patterns for these specific Victaulic FireLock automatic sprinklers. They are provided as information for guidance in avoiding obstructions to sprinklers and should not be used as minimum sprinkler spacing rules for installation. Refer to the appropriate NFPA National Fire Code or the authority having jurisdiction for specific information regarding obstructions, spacing limitations and area of coverage requirements. Failure to follow these guidelines could adversely affect the perfor- mance of the sprinkler and will void all Listings, Approvals and Warranties. 3 All patterns are symmetrical to the centerline of the waterway. www.victaulic.com \JtauIicr vicTAuLic IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2009 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 40.55_6 REV_A FIRE PROTECTION PRODUCTS - AUTOMATIC SPRINKLERS 40.55 V38, K5.6 300 psi/2068 kPa High Pressure Adjustable Concealed Standard Spray Pendent Standard and Quick Response V3807 STANDARD RESPONSE V3808 QUICK RESPONSE WARRANTY Refer to the Warranty section of the current Price List or contact Victaulic for details. NOTE This product shall be manufactured by Victaulic or to Victaulic specifications. All products to be installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations. www.victaulic.com /tauiicr VICTAULIC IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2009 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REV_A 40.55_7 Adjustable Concealed Standard Spray Pendent Standard and Quick Response V3807 STANDARD RESPONSE V3808 QUICK RESPONSE For complete contact information, visit www.victaulic.com ,4tauiicr 40.55 5562 REV A UPDATED 4/2009 VICTAIJLIC IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2009 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 40.55 FireLock® V27, K56 Models V2703, V2707, V2704, V2708 Standard Spray Upright, Pendent and Recessed Pendent Standard and Quick Response - V2703/V2704 V2707/V2708 V2707/V2708 Upright Pendent Recessed Pendent Approvals/Listings: 0786 See Victaulic Publication 1001 for more details. Product Description: These Model V27 standard spray sprinklers are designed to produce a hemispherical spray pattern for standard commercial applications. They are available with either standard or quick response bulbs. It is cast with a hex-shaped wrench boss to allow easy tightening from many angles, reducing assembly effort. This sprinkler is available in various temperature ratings (see chart on page 3) and finishes to meet many design requirements. The recessed pendent should be utilized with a Model V27 recessed escutcheon which provides Up to /4719 mm of adjustments. Coverage For coverage area and sprinkler placement, refer to NFPA 13 or applicable standard. JtauIic 40.10 Technical Specifications: Models: V2703, V2704, V2707, V2708 Style: Pendent, Upright or Recessed Pendent Nominal Orifice Size: 1/2713 mm K Factor: 5.6 Imp./8.1 SI.1 Nominal Thread Size: ½" NPT/15 mm Max. Working Pressure: 175 psi/1200 kPa (FM) 250 psi/1725 kPa (UL) Factory Hydrostatic Test: 100% @ 500 psi/3450 kPa Mm. Operating Pressure: 7 psi/48 kPa 0.35 bar/5 psi (VdS for upright only) Temperature Rating: See chart 1 For K-Factor when pressure is measured in Bar, multiply S.I. units by 10.0. Exaggerated for clarity Job/Owner System No. Location Contractor Submitted By Date Engineer Spec Section Paragraph Approved Date victaulic.com I Sprinklers I FireLock® I K5.6, V27 I Publication 40.10 40.10 2544 Rev. J Updated 07/2014 © 2014 Victaulic company. All rights reserved. ictaulic 1 victaulic.com I Sprinklers I FireLock I K5.6, V27 I Publication 40.10 Material Specifications: Accessories Upright Deflector: Bronze per UNS C11000 Pendent Deflector: Bronze per UNS C51000 Bulb: Glass with glycerin solution Bulb Nominal Diameter: El Standard: 5.0 mm LI Quick Response: 3.0 mm Load Screw: Bronze per UNS C65100 Pip Cap: Bronze per UNS C65100 Spring: Beryllium nickel Seal: Teflon2 tape Frame: Die cast brass 65-30 Lodgement Spring: Stainless steel per UNS S30200 Installation Wrench: LI Open End: V27 LI Recessed: V27-2 Sprinkler Finishes: LI Plain Brass LI Chrome plated LII White painted3 LI Black painted3 LI Custom painted3 LI Proprietary Nickel Teflon2 coating3 LI VC-2504 155, 200, 286 SR Only: LI Wax3 For cabinets and other accessories refer to separate sheet. 2 Teflon is a registered trademark of Dupont Co. UL Listed for corrosion resistance. UL Listed and FM Approved for corrosion resistance. 40.10 2544 Rev. J Updated 07/2014 © 2014 Victsulic Company. All rights reserved. ictaullilce victaulic.com 2 victaulic.com I Sprinklers I FireLock5 I K5.6, V27 I Publication 40.10 Approvals/Listings: Model APPROVALS/LISTINGS V2703 V2707 V2707 V2704 V2708 V2708 Orifice Size (inches) 1/2" /2" 1/2" 1/2' 1/2" 1/7" Orifice Size (mm) 13 13 13 13 13 13 Nominal K Factor Imperial 5.6 5.6 5.6 5.6 5.6 5.6 Nominal K Factor S.1.5 8.1 8.1 8.1 8.1 8.1 8.1 Response Standard Standard Standard Quick Quick Quick Def lector Type Upright Pendent Recessed Upright Pendent Recessed Pendent Pendent Approved Temperature Ratings F°/C° 1350F/570c 135"F/57°C 135"F/57"C 135"F/57"C 135"F/570c 155"F/68°C 1550F/68°c 155°F/68"C 1550F/680c 155°F/68"C 135"F/57"C cULus 175°F/79°C 175"F/79"C 175°F/79"C 175"F/79"C 175"F/79°c 155"F/68°C 200"F/93"C 200"F/93°C 200"F/93"c 200"F/93°C 2000F/93°C 175°F/79"C 286°F/141 "c 286"F/141 "c 286"F/141"C 286"F/141°c 286°F/141 "C 200°F/930C 360"F/182°C 360°F/182°C 135"F/57°c 135°F/57"C 135°F/57°C 135°F/570c 155"F/68"C 155"F/68"C 135°F/57"C 155"F/68"C 155"F/68"C 135°F/57°C FM 175"F/79"C 175"F/79"C 155"F/68"C 1750F/79"c 175"F/79"c 155"F/68"C 200"F/930C 200°F/93°c 175"F/79"C 200"F/93"C 200°F/93°C 175"F179°C 286"F/1410c 286°F/141°c 200°F/93"C 286°F/141°C 286°F/141°C 200"F/93"C 360"F/182"C 360"F/1820C 1350F/57"C 135°F/570c 135°F/570C 135°F/570c 135"F/57"C 155°F/68°c 155°F/68"C 1550F/68"c 155"F/68"C 155"F/68°C 135"F/57°C NYC/MEA 62-99-E 175"F/79°c 175°F/790C 175°F/79"C 175"F/79"C 175"F/79"C 155°F/680C 200"F/93"C 200°F/93°C 200°F/930C 200°F/93°C 200"F/93"C 175"F/79"C 286°F/141°C 286°F/141 "C 2860F/141 *C 286"F/141"C 286"F/141°C 200°F/930C 360"F/182"C 360"F/182"C 135"F/57°C 135"F/57°C 135°F/57°C 135"F/57"C 135"F/57"C 155"F/68"C 1550F/680C 155"F/68"C 155"F/68"C 155"F/68°C 135"F/57°C CSFM 7690-0531:112 175"F/79°C 175°F/790C 175"F/79"c 175°F/79°C 175"F/79"C 1550F/680C 200°F/93°C 200"F/93"C 200"F/93"C 200"F/93°C 200°F/930C 175°F/79°C 286"F/141°C 286°F/141°C 286°F/1410C 2860F1141"C 286"F/141 "C 200°F/93°C 360"F/182"C 360"F/182°C 1350F/57'C 155°F/680c 135°F/57°C -PCB 175°F/790C None None 1S5°F/68°C None None 200°F/930C 175°F/79°C 2860F/1410C 200°F/930C 360°F/1820C 135°F/57°C 135°F/570C 135°F/570C 135°F/57°C 155°F/680C 155°F/68°C 135°F/570C 155°F/68°C 155°F/68°C 135°F/57°C VNIIPO 175°F/79°C 175°F/79°C 155°F/680C 175°F/79°C 175°F/79°C 1550F/68°C 200°F/93°C 200°F/93°C 175°F/79°C 200°F/93°C 200°F/93°C 175°F/79°C 286°F/141°C 286°F/141 °C 200°F/93°C 2860F/1410 c 286°F/141 °C 200°F/93°C 360°F/182°C 360°F/1820C ZSTZ ZSTX K-ZSTZ K-ZSTZ ccc 155°F/68°C 155°F/68°C None 155°F/68°C 155°F/68°C None 200°F/93°C 200°F/93°C 200°F/930C 200°F/93°C 135°F/57°C 135°F/57°c 155°F/68°C 155°F/68"C VdS 175°F/79°C None None 175°F/79°C None None 200°F/93°C 200°F/93°C 286°F/141°c 286°F/141°c 360°F/182°C 135°F/57°C 135°F/57°c 155°F/68°c 155°F/68°c CE 175°F/79°c None None 175°F/790C None None 200°F/93°C 200°F/93°C 286°F/141 °c For K Factor when pressure is measured in Bar, multiply S.I. units by 10.0 FM Approved with 1/2" adjustment escutcheon only - quick response Note: Listings and Approvals as of printing. All are approved open. 40.10 2544 Rev. J Updated 07/2014 © 2014 Victaulic Company. All rights reserved. victaulic.com 3 'taUIiC 37 mm 2 60 2W/ 41 mm 60 mm victaulic.com I Sprinklers I FireLock I K5.6, V27 I Publication 40.10 Dimensions: Standard Pendent— Standard upright - V2707. V2708 V2703, V2704 2W/sO mm Max. Hole 2/51 mm Mm. Hole Typical Cei 30 ling Tile all T wy -Finished Surface 37M MAXIMUM RECESS 215/W/ 75 mm MAXIMUM EXTENSION ½ Adjustment Recessed - V2707, V2708 (drawing not to scale) P 2W/60 mm Max. Hole 2/51 mm Mix. Hole 8mm Typical Ceiling Tile 24 mm LL ___ MAXIMUM RECESS 256/ 75 mm MAXIMUM EXTENSION 3/4"Adjustment Recessed - V2707, V2708 (drawing not to scale) 40.10 2544 Rev. J Updated 07/2014 16 2014 Victaulic Company. All rights reserved. victaulic.com 4 \1tauIic 17mm 43 mrs victaulic.com I Sprinklers I FireLock® I K5.6, V27 I Publication 40.10 Distribution Patterns: Models V2707, V2708 K5.6 Standard Pendent and Recessed Pendent 10' 3am B. 2.4n, 4, L2rrr 2' 0.onr IRK 7 psi 48 kPa 15 psi 103 kPa 30 psi 207 kPa 2' 4' 6' 8' 10' 12' 14' 0.6,, 1.2rrr 18,rr 2.4r0 3.0m 3.7nr 4.3rrr Models V2703, V2704 K5.6 Standard Upright Distribution Patterns - Trajectory - - . - - I N I - - - - . - - - - - E I111\JI5 2 4' 6' 8' 10 12' 14 16' 0.60, 1.20, 1.8,, 2.40r 3.0,0 3.7,,, 4.3,, 4.901 NOTES: Data shown is approximate and can vary due to differences in installation. These graphs illustrate approximate trajectories, floor-wetting, and wall-wetting patterns for these specific Victaulic FireLock Automatic Sprinklers. They are provided as information for guidance in avoiding obstructions to sprinklers and should not be used as minimum sprinkler spacing rules for installation. Refer to the appropriate NFPA National Fire Code or the Authority Having Jurisdiction for specific information regarding obstructions, spacing limitations and area of coverage requirements. Failure to follow these guidelines could adversely affect the performance of the sprinkler and will void all Listings, Approvals and Warranties. All patterns are symmetrical to the centerline of the waterway, 40.10 2544 Rev. J Updated 07/2014 © 2014 Victaulic Company. All rights reserved. victaulic.com 5 \/tauIic 10, 8' 2.4m 6' 1.8,,, 4' L2nr 7, 04rn 11 7 psi 48 kPa 15 psi 103 kPa 30 psi 207 kPa victaulic.com I Sprinklers I FireLock® I K5.6, V27 I Publication 40.10 Ratings: Available Wrenches: All glass bulbs are rated for temperatures from -67°F (-55°C) to those shown in the table below. Sprinkler Temperature Classification Victaulic Part Identification Temperature _— Glass Bulb Color Nominal Temperature Rating Maximum Ambient Temperature Allowed Ordinary A 135°F/570C 1001F/380C Orange Ordinary C 155°F/68°C 100°F/38°C Red Intermediate E 1750F/790C 150°F/65°C Yellow Intermediate F 200°F/930C 1500F/651C Green High J 286°F/1410C 2250F 8/1070C Blue Extra High 7 K 360°F/1 82°C 300°F/1490C Purple - M Open - No Bulb Standard response only. 8 150/65 if wax coated. V27-2 Recessed V27 Open End V2707,V27O8Pendent V2707,V2708 Recessed Pendent V2703.V2704 upright WARNING Always read and understand installation, care, and maintenance instructions, supplied with each box of sprin- klers, before proceeding with installation of any sprinklers. Always wear safety glasses and foot protection. Depressurize and drain the piping system before attempting to install, remove, or adjust any Victaulic piping products. Installation rules, especially those governing obstruction, must be strictly followed. Painting, plating, or any re-coating of sprinklers (other than that supplied by Victaulic) is not allowed. Failure to follow these instructions could result in serious personal injury and/or property damage. The owner is responsible for maintaining the fire protection system and devices in proper operating condition. For O minimum maintenance and inspection requirements, refer to the current National Fire Protection Association pam- phlet that describes care and maintenance of sprinkler systems. In addition, the authority having jurisdiction may have additional maintenance, testing, and inspection requirements that must be followed. If you need additional copies of this publication, or if you have any questions about the safe installation of this product, contact Victaulic World Headquarters: P.O. Box 31, Easton, Pennsylvania 18044-0031 USA, Telephone: 1 WE WJ 0 001-610-559-3300. Installation Nate Reference should always be made to the 1-40 Victaulic FireLock Automatic Sprinklers This product shall be manufactured by Victaulic or to Victaulic specifications. All products Installation and Maintenance Sheet for the product you are installing. This installation sheet to be installed in accordance with current Victaulic inslallatios/asserribly instructions. is included with each shipment of Victaulic products for complete installation and assembly Victaulic reserves the right to change product specifications, designs and standard data, and is available in REF format on our website at victaulic.com. equipment without notice and without incoming obligations. Warranty Trademarks Refer to the Warranty section of the current Price List or contact Victaulic for details. Victaulic is registered trademark of Victaulic Company. 40.10 2544 Rev. .1 Updated 07/2014 0 2014 Victaulic Company. All rights reserved. victaulic.com 6 '/(tauIic Extended Coverage Light Hazard Adjustable Concealed Pendent V3102 Quick Response V3104 Quick Response The Model V31 ECLH Concealed sprinklers are designed with either a K8.0 or K11.2 orifice size to provide added coverage at normal light hazard operating pressures. This concealed, designer style sprinkler allows up to 1/8'/16 mm adjustment to accommodate concealment needs. Extended spray coverage is up to 400 square feet (37,2 sq. m) per NFPA 13 Light Hazard design criteria. The integral wrench plate in the cup allows for ease of installation with the V31N33 wrench by engaging the cup instead of the sprinkler frame. EXTENDED COVERAGE LIGHT HAZARD ADJUSTABLE CONCEALED PENDENT V3102, V3104 SPRINKLER OPERATION: The operating mechanism is a frangible glass bulb which contains a heat responsive liquid. During a fire, the ambient temperature rises causing the liquid in the b.ulb to expand. When the ambient temperature reaches the rated temperature of the sprinkler, the bulb shatters. As a result, the waterway is cleared of all sealing parts and water is discharged towards the deflector. The deflector is designed to distribute the water in a pattern that is most effective in controlling the fire. COVERAGE: For coverage area and sprinkler placement, refer to NFPA 13 standards. JOB/OWNER CONTRACTOR System No. Submitted By_ Location Date www.victaulic.com viciuic IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2013 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REV..A ENGINEER Spec Sect _____________ Para Approved Date X.A tc - 40.761 FIRE PROTECTION PRODUCTS - AUTOMATIC SPRINKLERS 4036 V311 K8.07 K11.2 Extended Coverage Light Hazard Adjustable Concealed Pendent V3102 Quick Response —+V3104 Quick Response TECHNICAL SPECIFICATIONS: Exaggerated for clarity Models/SIN.: V3102, V3104 Style: Extended Coverage Light Hazard Concealed Nominal Orifice Size: 7/32' 14mm, 5/8" 16mm K-Factor: V3102: 8.0 Imp/11.5 SI V3104: 11.2 Imp/ 16.2 SI Nominal Thread SizeiNiJ(20mm) Max. Working Pressure: 175psi/1200kPa Factory Hydrostatic Test: 100% @500psi/34501kPa Mm. Operating Pressure: 7p5i/48kPa Temperature Rating: See chart on page 2 MATERIAL SPECIFICATIONS Pendent Deflector: Brass per UNS C51000 Bulb: Bulb with Glycerin Solution Bulb Nominal Diameter: Quick Response: 3.0mm Load Screw: Bronze per UNS 65100 Pip Cap: Bronze per UNS 65100 Seal: Teflon* tape Spring: Beryllium Nickel Frame: Die Cast Brass 65-30 Lodgement Spring: Stainless Steel per UNSS3O200 Cup: Cold rolled steel, zinc chrome plated Cover/Escutcheon: Brass per UNS C26000 reference v3801 for position ACCESSORIES Installation Wrench: Concealed Wrench: V31/V33 Sprinkler Finishes: Plain Brass only Coverplate Finishes: Chrome plated White painted Flat Black Custom Painted For cabinets and other accessories refer to Separate Sheet. A For K-Factor when pressure is measured in Bar, multiply S.I. units by 10.0. * Teflon is a registered trademark of Dupont Co. vicTAuLic IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. C 2013 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 40.76_2 REV.A FIRE PROTECTION PRODUCTS - AUTOMATIC SPRINKLERS V317 K8.01 K11.2 Extended Coverage Light Hazard Adjustable Concealed Pendent V3102 Quick Response V3104 Quick Response 40.76 4 Listings and Approvals as of printing. For K Factor when pressure is measured in Bar, multiply S.I. units by 10.0 # Light Hazard ONLY www.victaulic.com j4tauiic VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2013 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REV_A 40J6_3 FIRE PROTECTION PRODUCTS - AUTOMATIC SPRINKLERS 40.76 V311 K8.07 K11.2 Extended Coverage Light Hazard Adjustable Concealed Pendent V3102 Quick Response V3104 Quick Response RATINGS All glass bulbs are rated for temperatures from -67°F/-55°C to those shown in table below. Ordinary A 135 57 100 38 Orange A 1350 100 57 I 38 155 Ordinary C 68 i T 100 165 150 38 Red Dl 74 65 1- t Intermediate E 75 150 Yellow 75 65 Intermediate F 200 93 150 Green 65 286 High J 141 225 Blue 107 Extra High I K 360 I 300 Purple + 182 149 j -4 M Open - I No Bulb 4 Standard response only. All standard responses are approved open. A For use with Standard or Quick Response Concealed Sprinkler 135F/57C or 155°F/68°C. t For use with Standard or Quick Response Concealed Sprinkler 175FI79°C or 2OOF/93°C. Custom Finish - Customer to provide paint specification, allow 4-6 weeks for samples. 0 138°F/59°C per LPBC ORDERING INFORMATION Please specify the following when ordering: Sprinkler Model Number Style Temperature Rating K-Factor Thread Size Quantity Sprinkler Finish Escutcheon Finish Wrench Model Number VICTAULIC IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. m 2013 vIcTAuLIc COMPANY. ALL RIGHTS RESERVED. X. A—c—ta U —1i e 40.76_4 REV_A FIRE PROTECTION PRODUCTS - AUTOMATIC SPRINKLERS 40.76 V31, K8.09 K11.2 Extended Coverage Light Hazard Adjustable Concealed Pendent V3102 Quick Response V3104 Quick Response DIMENSIONS V3102, V3104 - Minimum/Maximum Extension (drawing not to scale) 73h"/70 mm 6 hed MM MINIMUM EXTENSION MAXIMUM EXTENSION V3102, V3104 - After Activation Maximum Extension Shown Typical to Both Configurations (drawing not to scale) 23U'/ 65 mm I 46 mm 41 mm PERFORMANCE Sprinkler Performance FlowF and IPressure TIC 16X16 26 10.6 30 1 7.2 4,9X4,9 98 73.1 115 1 49.6 18X18 33 17.0 33 8.7 5,5 X5,5 125 40 117.2 25.0 125 40 I 60.0 (i8 20X20 6,1 X6,1 150 172.4 150 88.3 Note - Minimum installation distance is 8 feet. Sprinkler has been designed as per NFPA13 light hazard design density. www.victaulic.com 'JtauIic VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2013 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REV_A 40.76_5 FIRE PROTECTION PRODUCTS - AUTOMATIC SPRINKLERS V317 K8.01 K11.2 Extended Coverage Light Hazard Adjustable Concealed Pendent V3102 Quick Response V3104 Quick Response AVAILABLE WRENCHES 40.76 EC Concealed Pendent V31/V33 DISTRIBUTION PATTERNS Model V3102 K8.0 Extended Coverage Light Hazard Concealed Pendent Distribution Pendent 10' - 9. -I I I I I I I F I I I IiI1T1 I I11[TT1 0 1' 2' 3' 4' 5' 6' 7' 8' 9' 10' 11' 12' 13' 14' 15 16' 17 18' 19' 20' 21 22 23' 24' 259pm - - - 33 gpm 40 gpm ------ Model V3104 K11.2 Extended Coverage Light Hazard Adjustable Concealed Pendent Distribution IREàRRURURUUIU III.... 1111111 IUI....UUU II... uUUUUUUUUUU UI.. uUUUUU.IU... ONE IUUIUUUUIIII IN IIIlIUIIUUUU I N IIIIUUUUUUIUUU II I IIUIIIIIUIUUI II IIIIUIUIUUUII II .----------____ --- I 0 1' 2' 3' 4' 5' 6' 7' 8' 9' 10' 11' 12' 13' 14' 15' 16' 17' 18' 19' 20' 25 gpm - - - 33 9pm 40 gpm ------ NOTE 1. Data shown is approximate and can vary due to differences in installation. 2. These graphs illustrate approximate trajectories, floor-wetting, and wall-wetting patterns for these specific Victaulic FireLock Automatic Sprinklers. They are provided as information for guidance in avoiding obstructions to sprinklers and should not be used as minimum sprinkler Spacing rules for installation. Refer to the appropriate NFPA National Fire Code or the Authority Having Jurisdiction for specific information regarding obstructions, spacing limitations and area of coverage requirements. Failure to follow these guidelines could adversely affect the performance of the sprinkler and will void all Listings, Approvals and Warranties. VICTAULIC IS REGISTERED TRADEMARK OF viclAuLIc COMPANY. 0 2013 vICTAuLIc COMPANY. ALL RIGHTS RESERVED. 40.76_6 REV_A 5MUUUUUUUUUUUUUU a..... UUUUURUUUUU mmmmmmmmm auaam••a IUUUUUUUU mmmmmmmm aaauuuaaia aauause•u MMMMMM UUUUUUUUUUUU .UUUUU.UUU... U U U UUUU UUU UU RUUUU*URUUURUU UI..U.UIU.I... U. I 10' 9' 8' 7' 6' 5' 4' 3' 2- 1 . a Extended Coverage Light Hazard Adjustable Concealed Pendent V3102 Quick Response V3104 Quick Response WARRANTY Refer to the Warranty section of the current Price List or contact Victaulic for details. WARNING A WARNING Always read and understand installation, care, and maintenance instructions, supplied with each box of sprinklers, before proceeding with installation of any sprinklers. Always wear safety glasses and foot protection. Depressurize and drain the piping system before attempting to install, remove, or adjust any Victaulic piping products. Installation rules, especially those governing obstruction, must be strictly followed. Painting, plating, or any re-coating of sprinklers (other than that supplied by Victaulic) is not allowed. Failure to follow these instructions could result in serious personal injury O and/or property damage. The owner is responsible for maintaining the fire protection system and devices in proper operating condition. For minimum maintenance and inspection requirements, refer to the current National Fire Protection Association pamphlet that describes care and maintenance of sprinkler systems. In addition, the authority having jurisdiction may have additional maintenance, testing, and inspection requirements that must O be followed. If you need additional copies of this publication, or if you have any questions about the safe installation of this product, contact Victaulic World Headquarters: P.O. Box 31, Easton, Pennsylvania 18044-0031 USA, Telephone: 001-610-559-3300. For complete contact information, visit www.victaulic.com 40.76 6980 REV UPDATED 05/2013 VIcTAULIc IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2013 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 40.76 FireLock® Escutcheons FOR RECESSED OR FLUSH SPRINKLER INSTALLATION Victaulic FireLock Escutcheons are intended for use with Victaulic FireLock V24, V27, V29, V33, V34 and V36 recessed, flush, and extended pendent sprinklers. They are intended for use only with Victaulic FireLock sprinklers. Agency Approvals and Listings for Victaulic FireLock sprinklers require the use of Victaulic FireLock escutcheons exclusively. FireLock escutcheons are not Listed or Approved for use with any sprinklers other than Victaulic FireLock sprinklers. FireLock escutcheons are available in various finishes to meet many design requirements and are intended only for use with Victaulic sprinklers. Please reference the 1-40 Installation Manual before installing any product. NOTE: The V33 and V36 escutcheons are offered as part of a pre-assembled sprinkler product and are not available for individual purchase. V29 EXTENDED V29 FLUSH ESCUTCHEON ESCUTCHEON - V27 AND V34 RECESSED V27 AND V34 FLUSH ESCUTCHEON ESCUTCHEON TECHNICAL SPECIFICATIONS: Material: Cold Rolled Steel Optional Materials: Brass Stainless Steel Finishes: Chrome White Custom NOTE: All Nickel Teflon* sprinklers must use stainless steel escutcheons. Stainless steel and brass options are available painted black, white or custom. See current Price List for complete offering. For expansion plate information, please refer to submittal publication 40.84. * Teflon is a registered trademark of Dupont Corporation JOB OWNER CONTRACTOR ENGINEER System No. Submitted By Spec Sect Para__________ Location Date Approved www.victaulic.com VICTAULIC IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2011 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REVB jLtauiic 40.8&.1 FIRE PROTECTION PRODUCTS - AUTOMATIC SPRINKLER ACCESSORIES FireLock® Escutcheons FOR RECESSED OR FLUSH SPRINKLER INSTALLATION mm 65.10HIM 15.91 mm 12.70 MM V29 EXTENDED ESCUTCHEON 1129 FLUSH ESCUTCHEON 27/8 3,03 mm _ L,71.37mj JH _ 3.1m I¼oru// Adjostmett to ~ or w/tg.os 28.58 or 20.64mm 12.70 mm or 12.70 mm 1127 AND 1134 RECESSED ESCUTCHEON V27 AND V34 FLUSH ESCUTCHEON * NOTE: THIS ESCUTCHEON CAN BE ADJUSTED TO RECESS ½ OR 3/4"I12.70 OR 19.05 MM www.victaulic.com \J#taUIiC VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2011 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 40.8813 REV—El Escutcheons FOR RECESSED OR FLUSH SPRINKLER INSTALLATION WARRANTY Refer to the Warranty section of the current Price List or contact Victaulic for details. NOTE This product shall be manufactured by Victaulic or to Victaulic specifications. All products to be installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations. UPDATED 2/2011 ,,#'tauIicr 40.88 6321 REV B VICTAULIC IS REGISTERED TRADEMARK OF VITALi COMPANY. © 2011 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 40.88 FM Approved and UL Listed Sprinkler Pipe Bull Moose Tube Company is a recognized producer of quality pipe products. Our Schedule 10 and Schedule 40 are FM Approved and UL Listed (for U.S. and Canada), even though these products do not require separate approvals and listings. Bull Moose Tube made the decision to have them approved and listed for your peace of mind. Our Sch. 10 and Sch. 40 have been through the same rigorous testing as our other fine pipe products. Bull Moose Tube's Sch. 10 and Sch. 40 pipes are made to ASTM A135 and ASTM A795. These products are typically supplied with our protective coating but can be supplied without the coating so they can be hot-dip galvanized to meet FM requirements for use in dry systems in accordance with the zinc coating specifications of ASTM A795 or ASTM A53. Schedule 10 Pipe II R& am mom @000@W 1 1.315 1.097 1.41 lbs/ft 91 11/4 1.660 1.442 1.81 lbs/ft 61 11/2 1.900 1.682 2.09 lbs/ft 61 2 2.375 2.157 2.64 lbs/ft 37 21/2 2.875 2.635 3.53 lbs/ft 30 3 3.500 3.260 4.34 lbs/ft 19 4 4.500 4.260 5.62 lbs/ft 19 Schedule 40 Pipe II MAMO@Aft I ftffiwaaft I 1 1 1.315 1.049 1.68 lbs/ft 70 11/4 1.660 1.380 2.27 lbs/ft 51 11/2 1.900 1.610 2.72 lbs/ft 44 2 2.375 2.067 3.66 lbs/ft 30 2 1/2 2.875 2.468 5.80 lbs/ft 30 3 3.500 3.068 7.58 lbs/ft 19 4 4.500 4.260 10.80 lbs/ft 19 PIPE PREPARATION For proper operation, all pipe surfaces should be cleaned prior to installation. In order to provide a leak-tight seat for the gasket, pipe surfaces should be free from indentations and projections from the end of the pipe to the groove. All loose paint, scale, dirt, chips, grease, and rust must be removed prior to installation. Failure to take these important steps may result in improper coupling assembly, causing leakage. Also, check the manufacturer's instructions for the specific fitting used. Chesterfield, MO 63017 contact your salesperson C®uS A AIN- q 9 Chester 1819 Clarkson Road For additional information, (800) 325-4467 today at (800) 325-4467 or LISTED BULL. MOOSE TUBE CCIVIPANY FAX: (636) 537-2645 (636) 537-2600 in the USA, www.bullmoosetube.com or from Canada Ae> ACRPcompany e-mail: saIesbu11moosetube.com call (800) 882666 ______ APPROVED All information contained herein is accurate as known at the time of publication. Bull Moose Tube reserves the right to change product specifications without notice and without incurring obligation. 8/08 c®tjs LISTED [] A ON NFPA' Dull Moose Tube'sEddythread40 ADVANTAGES OF BULL MOOSE TUBES EDDYTHREAD 40 U is a lightweight replacement for • Has a Corrosion Resistance Ratio of 1.0. Schedule 40 that has a Corrosion • Has a pressure rating of 300 psi. Resistance Ratio of 1. • Is lighter weight than Schedule 40. Is approved by Factory Mutual and listed by Underwriters Laboratories. Is produced in accordance to ASTM Al 35 and A195 Type E, Grade A. Can be used with standard Schedule 40 threaded fittings, couplings, and valves. Is produced from steel with excellent properties of strength and threadability. Can be used in wet, preaction, and deluge type sprinkler systems. Can be hot dipped galvanized to meet FM's requirement for dry systems. Offers lower freight costs. Supplied with EDDY GUARD 110 MIC preventative coating. EDDYTHREAD 40 SPECIFICATIONS NOMINAL PIPE O.D. I.D. WEIGHT WATER FILLED BUNDLE SIZE (IN) (IN) (IN) CRR LB./FT WEIGHT SIZE 1 1.295 1.083 1.00 1.461 1.860 70 1-1/4 1.650 1.418 1.00 2.070 2.754 51 1-1/2 1.900 1.654 1.00 2.547 3.468 - 44 2 2.375 2.123 100 3.308 4842 30 'corrosion Resistance Ratio per latest UL Directory Listing PIPE PREPARATION For proper operation, all pipe surfaces should be cleaned prior to installation. In order to provide a leak-tight seat for the gasket, pipe surfaces should be free from indentations and projections from the end of the pipe to the groove. All loose paint, scale, dirt, chips, grease, and rust must be removed prior to installation. Failure to take these important steps may result in improper coupling assembly, causing leakage. Also, check the manufacturer's instructions for the specific fitting used. Q For Additional Information Contact (800) 325-4467 www.buIlmoosetube.com Or From Canada Call: (800) 882-4666 sales@buIlmoosetube.com 1819 Clarkson Road Chesterfield, MO Gerald, MO KeotWA Casa Grand" DallasTX Maury OH 63017 5 Bull Moose Tube's Eddylite is a lightwall threadable pipe manufactured in NPS 1 " through 2". Eddylite is a truly unique product within the fire protection industry. This product has been engineered to provide lower cost fire protection systems without compromising service life, adequate wall thickness, or standard outside diameter. Eddylite is manufactured to meet the requirements of ASTM A135 and A795 specifications. This pipe product has been fully approved by Factory Mutual, and listed by Underwriters Laboratories (for U.S. and Canada) for use in fire protection systems with a working pressure of 300 psi or less. c®us LISTED APPROVED no NFPA" 6 ADVANTAGES OF BULL MOOSE TUBES EDDVLITE Standard outside diameter, unlike some other lightwall threadable pipe products. Lighter in weight than Schedule 40. Superior burst strength and corrosion resistance ratio compared to other lightwall threadable pipe products. Exceptionally strong, meets or exceeds ASTM Al 35 minimum yield requirements. Can be used with standard couplings, fittings, and valves. Freight savings. Lower sprinkler system costs without compromising service life. Better hydraulics than Schedule 40. Wall thickness and weight close to Schedule 30; compare to other lightwall threadable water filled products with wall thickness less than Schedule lol CORROSION RESISTANCE RATIO (CRR) NOMINAL STANDARD INSIDE UL UL WEIGHT WATER BUNDLE PIPE SIZE (IN) O.D. (IN) DIAMETER (IN) THREADED UNTHREADED PER FT. FILLED SIZE 1 1.315 1.137 0.13 7.47 1.260 1.700 91 11/4 1.660 1.482 008 479 1.617 2.364 61 11/2 1.900 1.712 012 453 1.967 2.965 61 2 2.375 2.177 016 431 2.617 4.230 37 'Corrosion Resistance Ratio per latest UL Directory Listing PIPE PREPARATION For proper operation, all pipe surfaces should be cleaned prior to installation. In order to provide a leak-tight seat for the gasket, pipe surfaces should be free from indentations and projections from the end of the pipe to the groove. All loose paint, scale, dirt, chips, grease, and rust must be removed prior to installation. Failure to take these important steps may result in improper coupling assembly, causing leakage. Also, check the manufacturer's instructions for the specific fitting used. Q For Additional Information Contact (800) 325-4467 www.bulImoosetube.com Or From Canada Call: (800) 882-4666 saIes@buIlmoosetube.com 1819 CIa/mon Road Chesterfield, MO Gerald. MO Kent WA Casa Grande, A2 Dalla1X Masun,tOH 61017 NO. 20 TEE NO. 10 ELBOW ALTERNATE STYLES Victaulic offers a broad line of fittings in sizes through 60"/1500mm in a variety of straight and reducing styles. Most standard fittings are cast of durable ductile iron to precise tolerances. Victaulic standard fittings pressure ratings conform to the ratings of Victaulic Style 77 couplings. All fittings are supplied with grooves to permit fast installation without field preparation. The grooved design permits flexibility for easy alignment. These fittings are not intended for use with Victaulic couplings for plain end pipe (refer to Section 14.04 for fittings available for plain end applications). Fittings are provided in various materials including ductile iron, steel or segmentally welded steel depending on styles and size. Fittings are painted orange enamel with a galvanized finish available as an option, contact Victaulic for details. Victaulic fittings are designed specifically for use in grooved piping systems. Fittings are provided grooved conforming to standard steel pipe outside diameters. When connecting wafer or lug-type butterfly valves directly to Victaulic fittings with 741 or 743 VicFlangeW adapters, check disc clearance dimensions with I.D. dimension of fitting. Note: The following Victaulic fittings are VdS approved: No.10 90° Elbow, No.11 45° Elbow, No.20 Tee and No.60 Cap. Note: The following Victaulic fittings are _PCB approved: No.10900 Elbow, No.11 45° Elbow, No.12 22112 Elbow, No.13 111/40 Elbow, No.30 45° Lateral, No.30-R Reducing Lateral, No.100 Long Radius Elbow, No.110 Long Radius Elbow, No.20 Tee, No.35 Cross, No.60 Cap, No.25 Reducing Tee, No.33 True Wye, No.50 Concentric Reducer, No.51 Eccentric Reducer and No.29M Tee with Threaded Branch. Advanced Groove System - For 14-60"/350 - 1500 mm piping systems, Victaulic now offers the Advanced Groove System (AGS). Refer to Section 20.05 for AGS fitting details. Stainless Steel - Grooved end fittings are available in Schedule 10 Type 316 stainless steel (Schedule 5, 40 and Type 304 available as an option) in various sizes. Fitting center-to-end dimensions will vary depending upon type and schedule. Refer to Section 17.04 and 17.16 for details. Aluminum - Grooved end fittings are available in aluminum alloy 356 T6, in sizes from 1 - 8/25 - 200mm. Refer to Section 21.03 or contact Victaulic for details. Fabricated Steel - A full range of fabricated segemtnally welded steel or full flow grooved end fittings are available refer to section 07.04. Fabricated Steel with AGS Vic-Rings - A full range of full flow fabricated fittings with Vic-Rings are also available. AGS - ADVANCED GROOVE SYSTEM Extra Heavy EndSeal® 'ES" Fittings - EndSeal fittings are available in 2— 12/50 - 300mm for use with "ES" grooved pipe and HP-70ES EndSeal couplings. "ES" fittings are painted black for easy identification. EndSeal (and standard) fittings may be easily internally coated (by others) for severe service requirements. Always specify "ES EndSeal fittings" when ordering. See Section 07.03 for information on EndSeal fittings. Fittings Machined for Rubber or Urethane Lining (MRL) - For severe abrasive services, Victaulic fittings may be rubber or urethane lined (by others). Lining may be inside diameter/end (abrasion resistance) or wrap-around (corrosion and/or abrasion) machined. Refer to Section 25.03 or contact Victaulic for specific details. Note: Fittings are available with a variety of coatings upon request such as hot dip galvanized, epoxy, glass lined and others. JOB/OWNER CONTRACTOR ENGINEER System No. Submitted By Spec Sect - Para__________ Location Date Approved Date www.victaulic.com VICTAULIC IS REGISTERED TRADEMARK OF vicTAuLic COMPANY. © 2012 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REV_R \4taulicf 07.011 CARBON STEEL PIPE - GROOVED FITTINGS 07.01 Grooved End Fittings MATERIAL SPECIFICATIONS Fitting: Ductile iron conforming to ASTM A-536, grade 65-45-12. Ductile iron conforming to ASTM A-395, grade 65-45-15, is available upon special request. Or: Segmentally welded steel as shown under nipples Nipples: (adapter, swaged & hose) 3/4 - 4/20 - 100mm: Carbon steel, Schedule 40, conforming to ASTM A-53, Type F 5-6/125-- 150mm: Carbon steel, Schedule 40, conforming to ASTM A-53, Type E or 5, Gr. B 8— 12/200 - 300mm: Carbon steel, Schedule 30 or 40, conforming to ASTM A-53, Type E or 5, Gr. B Flanged Adapter Nipples: (Nipple - see above) Class 125 Flange: Cast iron conforming to ANSI B-16.1 Class 150 Flange: Carbon steel conforming to ANSI B-16.5, raised or flat face Class 300 Flange: Carbon steel conforming to ANSI B-16.5, raised or flat face Fitting Coatings: Orange enamel Optional: Hot dip galvanized and others. Some fittings supplied electroplated as standard - see product specifications. Flanged Adapter Nipple Coating: None (Unfinished) Optional: Orange enamel, hot dip galvanized and others. www.victaulic.com j#tauIict vICTAuLIC IS REGISTERED TRADEMARK OF vicrAuLic COMPANY.© 2012 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 07.01.2 REVR CARBON STEEL PIPE - GROOVED FITTINGS 07.01 Grooved End Fittings The chart expresses the frictional resistance of various Victaulic fittings as equivalent feet of straight pipe. Fittings not listed can be estimated from the data given, for example, a 221/20 elbow is approximately one-half the resistance of a 45° elbow. Values of mid-sizes can be interpolated. (51T Dimension - Feetimeters Y. 1 1.315 1.7 0.8 4.2 1.7 25 33.7 2.375 0.5 3.5 - 2.5 0.2 1.8 - 1.1 j 1.3 8.5 0.5 3.5 2 50 60.3 3.000 1.1 4.3 0.8 0.5 2.1 0.3 10.8 4.3 76.1 mm 76.1 3.500 1.3 5.0 - 3.8 0.7 2.6 - 1.6 3.3 13.0 1.3 F 5.0 3 80 88.9 4.250 1.5 6.4 1.2 0.8 3.2 0.5 4.0 15.3 1.5 6.4 1080 mm 108.0 4.500 2.0 6.8 - 5.0 0.9 3.4 - 2.1 4.7 16.0 2.0 6.8 4 100 114.3 J 5.250 - - 8.1 1.5 1.0 4.1 0.6 4.9 20.0 2.1 8.1 133.0mm 133.0 5.500 2.5 8.5 - 1.2 4.2 - 6.2 21.0 2.5 8.5 139.7 mm 139.7 5.563 2.6 8.5 + I - 4 1.3 4.2 - 6.4 21.0 2.6 8.5 5 125 141.3 j 6.250 2.6 9.4 . - - 1.3 4.9 4 - - 6.4 25.0 2.6 9.6 icon mm 159.0 + 6.500 2.9 9.6 4 1.5 5.0 , + 7.6 25.0 2.9 10.0 1 mm 165.1 + 6.625 2.9 10.0 + - 7.5 1.5 5.0 4 - + 3.0 I 7.6 25.0 3.0 10.0 6 150 168.3 8.625 3.0 13.0 4 2.3 - 4 9.8 1.5 6.5 4. 09 I . + 4.0 7.6 33.0 3.0 13.0 8 200 219.1 10.750 4.0 17.0 3.0 12.0 2.0 8.3 , 1.2 5.0 10.1 41.0 I 4.0 17.0 10 250 273.0 5.2 3.7 2.5 1.5 12.5 5.2 12 12.750 20.0 14.5 10.0 6.0 50.0 20.0 300 323.9 14.000 6.1 24.58 4 4.4 15.8 3.0 18.58 1.8 , 11.0 15.2 70.0 6.1 23.0 14 350 355.6 16.000 1 7.5 28.08 4.8 18.0 5.6 21.08 I 3.4 13.0 21.3 80.0 7.0 27.0 16 400 406.4 + 18.000 8.5 31.08 1 5.5 20.0 6.4 23.58 I 4.0 14.0 24.4 90.0 8.2 30.0 18 450 457.0 20.000 34.08 6.lj 22.5 7.2 25.5 § 16.0 27.4 100.0 49.1 I 33.0 20 800 508.0 24.000 10.4 42.0 § j 4 6.9 7.8 27.0 29.58 4.9 19.0 30.5 120.0 10.1 40.0 24 600 610.0 12.8 82 - 9.0 - 5.8 36.6 12.2 Fittings available up to 60/1500 mm. Contact Victaulic for details. 8 Contact Victaulic for details. 8 For roll grooved systems, Victaulic offers the Advanced Groove System (AGS). For pricing and availability of cut groove fittings in this size, contact your nearest Victaulic sales office. § Fitting flow data for 14-247350-600 mm size No. 10 and No. ii Elbows is based on fittings for Style 07 and 77 couplings. For flow data on AGS fittings (No. W1O and No. Wi 1 Elbows), refer to submittal 20.03. Note: All fittings are ductile iron unless otherwise noted with an "sw or Us". S= Carbon Steel Direct Roll Groove (OGS) SW= Carbon Steel Segmentally Welded www.victaulic.com VICTAULIC IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. 612012 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REV_R \%taulicr 07.013 FLOW DATA (Frictional Resistance) CARBON STEEL PIPE - GROOVED FITTINGS 07.01 Grooved End Fittings Reducing Tee bCtoE rCtoE..l NO. 25 Grooved Branch T NO. 29T Threaded Branch ft_1I ¼ C NO. 25 NO. 291 -0- C to to NO. 25-SW C to E -1 to NO. 29T-SW Size _ Ui Fiiu 1 1 3/4 2.25sw 2.245w 1.0 25 20 57 2.75 sw 57 2.75 sw 0.5 I 1.3 1¼ 1¼ 1 _i '4 32 25 70 2.75 sw 70 2.75 sw 0.6 1.5 1 ½ ½ 4 40 >' 40 '< 10 70 70 0.7 1 2.75 sw 2.75 sw 1.5 25 70 70 0.7 1¼ 2.7S sw 2.7S sw 1.7 70 0.8 ---.- - + 2 2' 3.25 3.25 2.5 50 >' 53 " 20 83 83 I 1.1 1 325 3.25 2.7 ...2... 83 + 83 1.2 1¼ 3.25sw 3.25sw 1.8 32 83 83 0.8 1 3.25 1 3.25sw 3.0 40 83 83 3.75 sw 1.4 3.9 2½ 21/2 V4 3.75sw x 65 65 >< 20 95 95 1.8 I. - 3.75 3.75 sw 3.8 23 95 95 1.7 11/4 3.75sw 3.75 sw 4.2 32 95 95 1.7 1 ½ 3.75 3.75 3.9 40 95 95 1.8 2 3.75 I 3.75 sw 4.5 50 95 4.25sw 95 4.25sw 2.0 5.7 3 3 3/4 x x 80 80 20 108 108 2.6 1 4.25 4.25 6.1 25 108 108 J' 2.8 1 ¼ 4.25 sw ' 1 4.25sw 8.0 32 108 .I 108 3,6 1 ½ 4.25 I 4.25sw I 6.5 40 108 108 2.9 2 4.25 4.25 sw 6.2 50 108 108 2.8 21/2 4.25 4.25sw 6.4 652. 108 108 5.00 sw j 2.9 8.0 4 4 3/4 5.tosw 100 X 100 X 20 127 127 3.6 1 5.00 5.00 t 7.8 25 127 127 1 3.5 Size r No = ~1 an I rcu W, ~ u R 4 4 11/4 5.00 sw 5.00 sw 9.6 100 > 100 32 127 127 44 1½ 5.00 5.00 10.2 40 127 , 127 4.6 2 5.00 5.00 11.2 50 127 127 5.1 2½ 5.00 5.00 11.4 65 127 127 5.2 3 5.00 5.00 11.6 80 127 5.50sw , 127 5,5Osw 5.3 14.0 5 5 1 125 125 140 140 6.4 - 1½ 5.50 sw I 5.50 sw 14.3 40 140 140 6.5 , 2 5.50 sw 5.50 sw 14.5 50 140 1 140 6.6 21/2 5.50 5.50sw 15.2 65 140 + 140 6.9 3 5.50 5.50 sw 16.6 80 140 140 7.5 t 4 5.50 5.50 sw 16.7 100 140 6,50 sw 140 6,5Osw 7.6 23.0 6 6 1 x 150 150 ><25 165 165 10.4 1112 6.50 sw 6.50sw 24.0 40 165 165 10.9 2 6.50 6.50 21.6 50 165 165 9.8 2½ 6.50 6.50 21.4 65 . 165 165 11.7 350-1500mm 4For AGS fitting information, see publication 20.05 + Contact Victaulic for details. Note: All fittings are ductile iron unless otherwise noted with an "sw' or "s' S= Carbon Steel Direct Roll Groove (005) SW= Carbon Steel Segmentally Welded IMPORTANT NOTE: No. 29T Threaded Outlet Reducing Tees are supplied NPT and are available with British Standard threads. For British Standard specify "BSP clearly on order. www.victaulic.com #ac tauIiC vicTAuLic IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2012 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 07.01_10 REVR CARBON STEEL PIPE - GROOVED FITTINGS Grooved End Fittings Reducing Tee i°1 r.CtoEl NO. 25 Grooved Branch ... 4 NO. 29T Threaded Branch to to NO. 25 NO. 29T 7 6 x 6 3 6.50 6.50 26.5 150 iso >8o 165 165 12.0 4 6.50 6.50 25.0 100 165 165 11.3 5 6.50 1 6.50 23.2 125 165 165 10.5 61/,, '½ 3 6.50 6.50sw 24.0 1631 > 1651 9_ 165 165 10.9 4 6.50 6.505w 25.0 100 165 165 11.3 8 8 1½ 7.75sw 7.755w 33.0 200 200 40 197 1 1 197 15.0 2 775 s 7.75 sw 33.5 50 197 197 15.2 7r7 __ 21/2 7.75sw 7.75sw 39.0 65 197 197 17.7 3 7.755w 775 s 33.6 ....L_197 , 197 15.2 4 7,75 7.75 41.8 .199.. .i. 197 19.0 5 7.755w 775sw 34.0 125 197 - 197 15.4 6 7.75 7.75 42.3 150 197 197 19.2 1651 7.75 SW 7.75 SW 48.0 197 197 21.8 10 x 10 x 11/2 9.00 1 9.00 62.0 250 250 .__.2_. 229 229 28.1 2 9.00 SW 9.005w 62.0 50 229 1 229 , 28.1 21/2 9.00sw 9.00sw 62.4 65 229 229 28.3 3 9.O0sw 9.00sw 60.0 80 , 229 , 229 27.2 4 9.005w 9.005w 61.0 100 229 229 277 5 9.005w 9.00sw 52.0 125 229 229 23.6 6 9.00sw 9.00sw 59.0 150 229 229 26.8 8 9.00sw 9.005w 64,7 200 229 229 29.3 07.01 Cto V C to NO. 29T-SW N o'Size •! u 12 12 x x 1 10.005w 10.00sw 77.0 300 300 2S 254 254 34.9 2 10.00sw I 10.00 SW 80.0 50 254 254 36.3 21/2 to.00sw 10.005w 78.0 65 254 254 35.4 3 10.00sw 10.00sw 82.0 80 254 254 37.2 4 10.00sw 10.00sw 80.0 100 254 254 - 36.3 5 10.005w 10.00sw 75.0 125 254 254 34.0 6 10,005W 10.00sw 75.0 150 254 254 34.0 8 10.005W 10.005w 80.0 254 254 36.3 t200 10 10.00 SW 10.005w 84.0 250 254 11.00 SW , 254 11.00 5W 38:1 102.0 #14 14 4 350 350 100 279 279 46.3 6 11.00 SW 11.00 SW 108.2 150 279 279 49.1 8 11.00 11.00 112.0 200 279 279 50.8 10 11.00 11.00 120.0 300 279 279 54.4 12 11.00 11.00 129.1 300 279 279 58.6 130.0 416 16 4 400 400 100 + + 59.0 14- 60" 350-150 mm 1 AGS For AGS fitting information, see publication 20.05 + Contact Victaulic for details. Note: All fittings are ductile iron unless otherwise noted with an "sw" or "s" S= Carbon Steel Direct Roll Groove (OGS) SW= Carbon Steel Segmentally Welded IMPORTANT NOTE: No. 291 Threaded Outlet Reducing Tees are supplied NPT and are available with British Standard threads. For British Standard specify 'BSP' clearly on order. 8 For roll grooved systems, Victaulic offers the Advanced Groove System (AGS). For pricing and availability of cut groove fittings in this size, contact your nearest Victaulic sales office. -o- C to E to NO. 25-SW www.victaulic.com \J1tauIic VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2012 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REV_R 07.01_11 CARBON STEEL PIPE - GROOVED FITTINGS Grooved End Fittings Reducing Tee NO. 25 Grooved Branch NO. 29T Threaded Branch 16 16 6 12.00sw 12.00sw 133.5 400 X 400 X 150 305 305 60.6 8 12.00 1 12.00 145.0 200. 305 305 65.8 10 12.00 12.00 149.5 250 305 305 67.8 12 12.00 12.00 154.0 300 305 305 69.9 H 120sw 1 '167.0 350 305 15.50sw - 15.50sw 75.8 194.0 9 18 18 4 40 X 450 19,4 394 4 94 88.0 - 6 15.50sw 15.50sw 200.0 'I 90.7 . 8 15.50sw 15.50sw 202.0 200 394 394 91.6 - 10 15.50 I 15.50 212.0 150 394 1394 96.2 12 15.50 15.50 222.6 300, 394 , 394 101.0 14 15.50 230.1 _59_ 394 .1 1044 16 15.50 247.6 . 400 394 17.25 - , 17.25 112.3 240.0 120 20 6 X X 500 500 150 43 • 438 j 108.9 17.25 17.25 - 244.0 200 438 438 ,j- 110.7 10 17.25 17.25 256.0 250 438 438 1 116.1 12 17.25 17.25 264.0 300 438 1 438 119.8 14 17.25 I 275.0 350 438 1 - 124.7 07.01 .ctot-1 -CtoE.j joL ~:H o NO. 25 NO. 29T Size No 25 Std. L wl No . 29T U #20 20 500 500 16 400 17.25 438 - 288.6 130.9 18 450 17.25 438 1 -134 20.00 20.00 508 508 297.0 .7 340.0 1542 24 24 8 ' 600 600 92_ 10 250 20.00 . 20.00 508 508 343.9 . 156.0 12 300 20.00 20.00 508 508 352.8 160.0 148 350 20.00 508 1 - 360.0 163.3 16 400 20.00 508 - 378.0 171.5 185 450 20.00 508 - 380.0 172.4 20 500 20.00 508 - 373.0 169.2 r-350-1500mm 4!'For AGS fitting information, see publication 20.05 + Contact Victaulic for details. Note: All fittings are ductile iron unless otherwise noted with an "sw' or "s' S= Carbon Steel Direct Roll Groove (005) SW= Carbon Steel Segmentally Welded IMPORTANT NOTE: No. 201 Threaded Outlet Reducing Tees are supplied NPT and are available with British Standard threads. For British Standard specify "BSP" clearly on order. # For roll grooved systems, Victaulic offers the Advanced Groove System (AGS). For pricing and availability of cut groove fittings in this size, contact your nearest Victaulic sales office. § Cast fitting available. Contact Victaulic for details. www.victaulic.com VICTAULIC IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2012 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 07.0112 J?tauIic REV_R INSTALLATION Reference should always be made to the 1-100 Victaulic Field Installation Handbook for the product you are installing. Handbooks are included with each shipment of Victaulic products for complete installation and assembly data, and are available in PDF format on our website at wNI.victaulic.com. WARRANTY Refer to the Warranty section of the current Price List or contact Victaulic for details. NOTE This product shall be manufactured by Victaulic or to Victaulic specifications. All products to be installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations. UPDATED 08/2012 07.01 1449 REV R 4C.t uIi vICTAULIC IS REGISTERED TRADEMARK OF vICTAULIC COMPANY. 2012 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 07.01 FireLock EZ® Rigid Coupling STYLE 009H The FireLock EZ Style 009H coupling is a rigid, installation-ready coupling for fire protection pipe joining. The coupling's unique design eliminates loose parts, insures consistent installation and provides substantial gains in productivity. IMPORTANT FireLock EZ Style 009H couplings are recommended for use ONLY on fire protection systems PATENTED LISTINGS/APPROVALS * The information provided below is based on the latest listing and approval data at the time of publication. Listings/Approvals are subject to change and/or additions by the approvals agencies. Contact Victaulic for performance on other pipe and the latest listings and approvals. Standard Pipe Size cULus/FM 1% 175 1 365 365 ' 365 365 32 1206 1 2517 2517 2517 I 2517 1112 175 1 365 365 365 1 365 40 1206 2517 2517 2517 2517 2 175 365 365 365 365 50 1206 2517 2517 2517 I 2517 21h 365 365 365 1 365 65 N/A 2517 2517 2517 j 2517 76.1 mm N/A N/A 365" 365 365 N/A 365 2517" 4 2517 2517 365 365 365 80 2517 365" 2517 365* 2517 ~ 2517 108 mm N/A 2517" 2517* N/A N/A N/A 365 365 t 365 t 365 I P0 2517 2517 2517 .j. + 2517 133 mm N/A 290m I 365" N/A N/A 1999* 2517" + - 139.7 mm N/A I N/A 290" J t 232 365 t 1999" 290" 1600 1 232 2517 t 365 165.1 mm N/A N/A 1999" 1600 2517 1 68 N/A 290 365 232 365 1508 1999 2517 1600 f 2517 * Listed/Approved for wet and dry pipe systems (>4o*F/4o*c). Please refer to the Victaulic Installation Manual (1-009H_009_009V.pdf) for details concerning when supplemental lubrication is required. ** EN-10219(L) for 76.1mm size; EN-10255(M) JOB/OWNER System No. Location Regional availability onlyd FM Approved only. CONTRACTOR Submitted By ENGINEER Spec Sect- Para__________ Approved Date www.victaulic.com viclAuLic IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. C 2012 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REVG dctauiicr 10.611 IPS CARBON STEEL PIPE - FIRE PROTECTION PRODUCTS 10.61 FireLock EZ® Rigid Coupling STYLE OO9H LISTINGS/APPROVALS * Speciality Pipe I3LT 11/4 -2 300 300 1¼-4 2068 300 2068 300 - OF 1¼-2 2068 300 2068 300 - DT 2068 2068 - El 1¼-4 1 175 175 1 1/4-2 1 I 1206 300 1206 300 - EL 1 ¼ - 2 2068 300 i 2068 300 - ET4O 2068 300 I 7088 2068 300 7068 EZI EZT 1 300 I 300 MT 11/4-2 300 300 - 1¼-4 2068k 300 2068 300 ¼-2 00602068 2068 N/A 2068 FF MLT 1 1/4-4 N/A 2068 300 11/4-2 1 N/A 8 300 ELF ST 114-2 N/A 2068 300 114-4 N/A 2068 300 FLT STF 114-2 N/A 300 214-4 2302068 N/A 2068 FLTL TE 300 300 1 A - 2 300 8 300 WLS 114-4 2068 Too 2068 300 114-2 2068 N/A 2068 175 MF WST 2068 2068 14-2 300 1206 300 XL I 2068 2068 Note The Specially Pipe table only applies to imperial sizes, NOT to metric sizes. www.victaulic.com \JtauIic VICTAULIC IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. 0 2012 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 10.612 REV.G STYLE 009H DIMENSIONS STYLE 009H PRE-ASSEMBLED (PUSH ON CONDITION) STYLE 009H JOINT ASSEMBLED IPS CARBON STEEL PIPE - FIRE PROTECTION PRODUCTS 10.61 FireLock EZ® Rigid Coupling STYLE 009H MATERIAL SPECIFICATIONS • u q Dimensions __ LJ :D- - - _& _i _ . 1¼ 1.660 365 790 0.10 2 - 3/852 2.95 4.77 2.70 4.63 1.93 1.4 32 42.4 1.900 2517 365 3514 2.54 1035 0.10 -M10x2 , 2 - 3/8 x2 1 75 3.19 121 69 4.97 2.94 118 4.79 49 , 1.93 0.7 1.5 1½ 40 48.3 2.37 5 2517 365 4604 2.54 1616 0.12 - Mb x 2 2 - 3/8s2 , 81 3.79 126 75122 5.53 3.45 5.42 49 1.93 0.7 1.9 2 50 60.3 2,875 2517 365 7193 3.05 2370 0.12 - Mb x 2 2 - 3/8 x 2½ 96 4.29 140 88 6.09 3.92 138 5.85 49 1.93 0.9 2.1 21/7 65 73.0 3.000 2517 365 10542 , 3.05 2580 0.12 -Mt0x2 1.6 2 -3/8 x 2 ½ 109 4.40 155 100 6.31 4.05 149 5.90 1 49 1.93 1.0 2.1 761 mm . 76.1 3.500 2517 365 11476 j 3.05 3512 0.12 -M10x2½ 2 - 3/8 x2½ 112 4.91 160 103 6.70 4.55 150 6.46 49 1.93 1.0 2.3 3 80 88:9 4.250 2517 365 15622 , 3.05 5178 0.17 -M10s2112 2 -3/8x I 1h 125 5.56 170 116 7.61 5.27 164 7.51 49 2.14 1.0 2.8 108 m 108.0 2517 23030 4.32 - MIO x2½ 141 193 134 191 J 54 1.2 4 4.500 365 5805 0.17 2 - 3/8 02½ 5.95 7.82 5.54 7.47 2.14 2.9 100 114.3 5.250 2517 365 25822 , 4.32 7900 0.17 - Mb 02½ 2 - 3/8x2 ½ 151 6.66 199 141 9.11 6.36 190 9.01 55 2.14 1.3 4.3 133 mm 133.0 5.500 2517 365 35140 4.33 8620 0.17 -Mb0x2½ 2 - 3/8x2 ½ 169 6.75 232 162 9.29 6.46 229 9.23 55 t 2.09 1.9 t 4.6 139.7 mm 139.7 6.500 2517 290 38340 + 4.32 9623 1 0.17 - Mb 0 x2½ . 2 - 5/8 x3¼ 172 .L 7.84 236 164 I 10.93 7.55 234 10.85 53 2.11 2.1 5.69 1651 mm 165.1 6.625 1999 290 , 42805 4.32 I 9997 0.17 - Mt6 x3¼ 2 - 5/8 s3¼ 199 7.96 278 192 11.08 7.67 276 11.99 54 2.11 2.6 5.92 6 150 168.3 1 1999 44469 4.32 -M16x31/4 202 281 195 305 54 2.69 Working Pressure and End Load are total, from all internal and external loads, based on standard weight (ANSI) steel pipe, standard roll or cut grooved in accordance with Victaulic specifications. See page 1 of this document for Listed/Approved ratings on other pipe. WARNING: FOR ONE TIME FIELD TEST ONLY, the Maximum Joint Working Pressure may be increased to 1112 times the figures shown in the chart on page 1, specific to pipe schedule and size. The allowable pipe separation dimension shown is for system layout purposes only. FireLock EZ couplings are considered rigid connections and will not accommodate expansion or contraction of the piping system. @ Number of bolts required equals number of housing segments. Housing: Ductile iron conforming to ASTM A-536, grade 65-45-12. Ductile iron conforming to ASTM A-395, grade 65-45-15, is available upon special request. Housing Coating: Orange enamel (North America, Asia Pacific) Red enamel (Europe) Optional Coatings: Hot dipped galvanized Gasket: Grade "E" EPDM (Type A) FireLock EZ products have been Listed by Underwriters Laboratories Inc., Underwriters Laboratories of Canada Limited, and Approved by Factory Mutual Research for wet and dry (oil free air) sprinkler services within the rated working pressure. Bolts/Nuts: Heat-treated plated carbon steel, trackhead meeting the physical and chemical requirements of ASTM A-449 and physical requirements of ASTM A-183. www.victaulic.com \JtauhcP VICTAC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2012 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REV..G 10.61_3 STYLE OO9H GENERAL NOTES NOTE: When assembling FireLock EZ couplings onto end caps, take additional care to make certain the end cap is fully seated against the gasket end stop. For FireLock EZ Style 009H couplings, use FireLock No. 006 end caps containing the "EZ" marking on the inside face or No. 60 end caps con- taining the "QV EZ" marking on the inside face. Non-Victaulic end cap products shall not be used with Style 009H couplings. IMPORTANT: Gaskets intended for the Style 009 or Style 009V couplings cannot be used with the Style 009H coupling. There is no interchanging of gaskets or housings between coupling styles. USE OF FLUSHSEAL GASKETS FireLock EZ couplings are supplied with FireLock EZ Grade "E" Type A gaskets. These gaskets FOR DRY PIPE SYSTEMS include an integral pipe stop, that once installed provides the same benefits as a FlushSeal gasket for dry pipe systems. It should be noted that standard FlushSeal gaskets are not compatible and cannot be used with the FireLock EZ couplings. INSTALLATION Reference should always be made to the 1-100 Victaulic Field Installation Handbook for the product you are installing. Handbooks are included with each shipment of Victaulic products for complete installation and assembly data, and are available in PDF format on our website at www.victaulic.com. WARRANTY Refer to the Warranty section of the current Price List or contact Victaulic for details. NOTE This product shall be manufactured by Victaulic or to Victaulic specifications. All products to be installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations. For complete contact information, visit www.victaulic.com 10.61 5731 REV G UPDATED 09/2012 VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2012 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 10.61 4tauiicr Victaulic® Flexible Coupling Style 75 - Exaggerated for clarity Approvals/Listings @1LPCBI® € See Victaulic publication 10.01 for details See Victaulic publication 02.06 for portable water approvals if applicable. Product Description Style 75 is available where moderate pressures are expected or weight considerations are a factor. Up to 50% lighter in weight than the Style 77, the Style 75 coupling is recommended for service up to 500 psi/3450 kPa depending on size. Housings are cast in two identical pieces in all sizes. Hot-dip galvanized and special coatings are available for all sizes. The Victaulic standard flexible coupling offering for grade "EHP" or "T" gaskets is the Style 177 installation-ready flexible coupling. For all available sizes, the Style 177 is the standard flexible coupling Victaulic supplies in North America for piping systems using Grade 'EHP" or "T" gaskets. Contact Victaulic for further details. Performance data presented in this document is based on use with standard wall, carbon steel pipe. For use with stainless steel pipe, please reference publication 17.09 for pressure ratings and end loads. When used on light wall stainless steel pipe, the Victaulic RX roll set must be used to roll groove the pipe. For further information regarding roll grooving stainless steel, refer to publication 17.01. 4tauIicr 06.05 I A WARNING Victaulic RX roll sets must be used when grooving light-wall/thin-wall stainless steel pipe for use with Victaulic Couplings. Failure to use Victaulic RX roll sets when grooving light-wall/thin-wall stainless steel pipe may cause joint failure, resulting in serious personal injury and/or NOTICE Victaulic RX grooving rolls must be ordered separately. They are identified by a silver color and the designation RX on the front of the roll sets. Job/Owner System No. Location Contractor Submitted By Date Engineer Spec Section Paragraph Approved Date victaulic.com I Couplings I Flexible I Style 75 I Publication 06.05 06.05 1470 Rev 0 Updated 09/2014 rO 2014 Victaulic company. All rights reserved. 1 iCtaUlic victauliccom I Couplings I Flexible I Style 75 I Publication 06.05 Material Specifications Housing: Bolts/Nuts: Ductile iron conforming to ASTM A-536, grade 65-45-12. Heat-treated plated carbon steel, trackhead meeting the Ductile iron conforming to ASTM A-395, grade 65-45-15, physical and chemical requirements of ASTM A-449 and is available upon special request. physical requirements of ASTM A-183 Housing Coating: (specify choice) LI Standard: Orange enamel. El Optional: Hot dipped galvanized and others. Gasket: (specify choice') NOTE: Additional gasket styles are available. Contact victaulic for details. L Grade "E" EPDM EPDM (Green stripe color code). Temperature range —30°F to +230°F/-34°C to +110°C. May be specified for cold and hot water service within the specified temperature range plus a variety of dilute acids, oil-free air and many chemical services. UL Classified in accordance with ANSI/NSF 61 for cold +73°F/+23°C and hot +180°F/+820C potable water service and ANSI/NSF 372. NOT COMPATIBLE FOR PETROLEUM SERVICES. LI Grade "1" Nitrile Nitrile (Orange stripe color code). Temperature range 20°F to +180°F/29°C to +82°C. May be specified for petroleum products, air with oil vapors, vegetable and mineral oils within the specified temperature range. Not compatible for hot water services over +150°F/+66°C or for hot dry air over +140°F/+600C. 1 Services listed are General Service Guidelines only. It should be noted that there are services for which these gaskets are not compatible. Reference should always be made to the latest Viclaulic Gasket Selection Guide for specific gasket service guidelines and for a listing of services which are not compatible. 06.05 1470 Rev 0 updated 09/2014 © 2014 victaulic Company. All rights reserved. victaulic.com 2 tauIic victaulic.com I Couplings I Flexible I Style 75 I Publication 06.05 Dimensions Style 75 -- to ito m L11 "Ii 'S4,f Actual Maximum Maximum Allow. Dimensions Approx. Nominal Outside Working End Pipe End Deflection from Weight Size Diameter Pressure 2 Load 2 Separation3 Centerline3 Bolt/Nut' X Y Z Each Pipe inches inches psi lbs. inches Per cplg. inches/ft. inches inches inches lbs. MM mm kPa N mm Degrees mm/rn (No.) size inches mm mm mm I kg 1 1.315 500 680 0-0.06 0.57 2.38 4.27 1.77 1.3 2°-43' 2- 3/ x 2 25 33.4 3450 3025 0-1.6 48 61 108 45 0.6 1 ¼ 1.660 500 1080 0-0.06 0.45 2.68 4.61 1.77 1.4 2°-b' 2-3/8x2 32 42.2 3450 4805 0-1.6 38 68 117 45 0.6 1 1/2 1.900 500 1420 0-0.06 0.40 2.91 4.82 1.77 1.5 1°-56' 2-3/ax2 40 48.3 3450 6320 0-1.6 33 74 122 45 0.6 2 2.375 500 2215 0-0.06 0.32 3.43 5.22 1.88 1.7 10- 31' 2-%x2 50 60.3 3450 9860 0-1.6 26 87 133 48 0.8 2 1/2 2.875 500 3245 0-0.06 0.26 3.88 5.68 1.88 1.9 11-15' 2-3/o x 2 65 73.0 3450 14440 0-1.6 22 98 144 48 0.9 3.000 500 3535 0-0.06 0.26 4.00 5.90 1.88 1.9 76.1 mm 10-12' 2-3/ax2 76.1 3450 15730 0-1.6 22 102 150 48 0.9 3 3.500 500 4800 0-0.06 0.22 4.50 7,00 1.88 2.9 10-2' 2-½x23% 80 88.9 3450 21360 0-1.6 18 114 178 48 1.3 3 1/2 4.000 500 6300 0-0.06 0.19 5.00 7.50 1.88 2.9 00- 54' 2-½X23/4 90 101.6 3450 28035 0-1.6 16 127 1 191 48 1.3 4 4.500 500 7950 0-0.13 0.34 5.80 8.03 2.13 4.1 1°-36' 2-½x234 100 114.3 3450 35380 0-3.2 28 147 204 54 1.9 4.250 450 6380 0-0.13 0.35 5.55 7.79 2.13 3.7 108.0 mm 1°-41' 2-12x70 108.0 3100 28395 1 0-3.2 29 1 141 198 54 1.7 41/2 5.000 450 8820 0-0.13 0.25 6.13 9.43 2.13 5.5 10- 26' 2-%x3¼ 120 127.0 3100 39250 0-3.2 21 156 240 54 2.5 5 5.563 450 10935 0-0.13 0.27 6.88 10.07 2.13 5.8 1°-18' 2-5/0x31/4 125 141.3 3100 48660 0-3.2 23 175 1 256 54 1 2.6 5.250 450 9735 0-0.13 0.28 6.55 9.37 2.13 6.0 133.0 mm 1°- 21' 2-16x82.5 133.0 3100 43325 0-3.2 24 166 238 54 2.7 139.7 mm 5.500 450 10665 0-0.13 1°-18' 0.28 2-%x3¼ 6.80 9.59 2.13 6.3 139.7 3100 47460 0-3.2 24 173 244 54 2.9 6.000 450 12735 0-0. 13 0.21 7.38 10.48 1.88 6.2 152.4 mm 1°-12' 2-%x3¼ 152.4 3100 56670 0-3.2 18 187 266 48 2.8 6 6.625 450 15525 0-0.13 0.23 8.00 11.07 2.13 7.0 1-5' 2-5/oX3¼ 150 168.3 3100 69085 0-3.2 18 203 281 54 3.2 6.250 450 13800 0-0.13 0.24 7.63 10.49 2.13 6.8 159.0 mm 1°- 9' 2- 16x82.5 159.0 3100 61405 0-3.2 20 194 266 54 3.1 8 8.625 450 26280 0-0.13 0.18 10.34 13.97 2.13 12.4 1 1 0--50' 2-3%x4¼ 200 219.1 3100 116945 0-3.2 14 263 355 59 5.6 2 Working Pressure and End Load are total, from all internal and external loads, based on standard weight (ANSI) steel pipe, standard roll or cut grooved in accordance with Victaulic specifications. Contact Victaulic for performance on other pipe. 3 Allowable Pipe End Separation and Deflection figures show the maximum nominal range of movement available at each joint for standard roll grooved pipe. Figures for standard cut grooved pipe may be doubled. These figures are maximums; for design and installation purposes these figures should be reduced by: 50% for 3/4 -3 1h"I20 -90mm; 25% for 4/100 mm and larger. 4 Number of bolts required equals number of housing segments. General Notes Metric thread size bolts are available (color coded gold) for all coupling sizes upon request. Contact Victaulic for details. WARNING: FOR ONE TIME FIELD TEST ONLY, the Maximum Joint Working Pressure may be increased to 11/2 times the figures shown. 06.05 1470 Rev 0 Updated 09/2014 0 2014 Victaulic Company. All rights reserved. victaulic.com 3 'j4'tauiic victaulic.com I Couplings I Flexible I Style 75 I Publication 06.05 Installation Note Reference should always be made to the 1-100 Victaulic Field Installation Handbook for This product shall be manufactured by Victaulic or to Victaulic specifications. All products the product you are installing. Handbooks are included with each shipment ot Victaulic to be installed in accordance with current Victaulic installation/assembly instructions. products for complete installation and assembly data, and are available In PDF format Victaulic reserves the right to change product specifications, designs and standard on our website at www.victautic.com. equipment without notice and without incurring obligations. Warranty Trademarks Refer to the Warranty section of the current Price List or contact Victaulic for details. Victaulic° is a registered trademark of Victaulic Company. 06.05 1470 Roy 0 Updated 09/2014 © 2014 Victaulic company. All rights reserved. victaulic.com 4 .4tauiic FireLock® Fittings X,4_r__t:a_U1iCr 10.03 Material Specifications: Fitting: Ductile iron conforming to ASTM A-536, grade 65-45-12. C Fitting Coating: El Orange enamel 0 Red enamel in Europe, Middle East, Africa, and India El Optional: Hot dipped galvanized Approvals/Listings: LPCB USTED Product Description: FireLock® products comprise a unique system specifically designed for fire protection services. FireLock full-flow elbows and tees feature CAD- developed, hydrodynamic design, affording a shorter center-to-end dimension than standard fittings. A noticeable bulge allows the water to make a smoother turn to maintain similar flow characteristics as standard full flow fittings. FireLock fittings are designed for use exclusively with Victaulic couplings that have been Listed or Approved for Fire Protection Services. Use of other couplings or flange adapters may result in bolt pad interference. Refer to the appropriate listing agency or approval body for pressure ratings. Pressure ratings vary by agency. Job/Owner System No. Location Contractor Submitted By Date Engineer Spec Section Paragraph Approved Date victaulic.com I FireLock® Fittings I Publication 10.03 10.03 1539 Rev M Updated 12/2014 © 2014 victaulic Company. All rights reserved. 1 X Ai______________ victaulic.com I FireLock® Fittings I Publication 10.03 Dimensions: Cto " toE C Ib=L to NO. 003 NO. 002 No. 006 No. 001 No. 003 No. 002 No. 006 900 Elbow 450 Elbow Straight Tee Cap Approx. Approx. Approx. Approx. Actual Nominal Outside Weight Weight Weight Weight Size Diameter C to E Each C to E Each C to E Each C to E Each inches inches inches Lbs. inches Lbs. inches Lbs. inches Lbs. mm mm mm kg mm kg mm kg mm kg 1¼ 1.660 0.82 0.3 32 42.4 - - - - - - 21 0.1 1½ 1.900 - - - - - - 0.82 0.4 40 48.3 - - - - - - 21 0.2 2 2.375 2.75 1.7 2.00 1.8 2.75 2.4 0.88 0.6 50 60.3 70 0.8 51 0.8 70 1.1 22 0.3 21/2 2.875 3.00 3.1 2.25 2.2 3.00 3.6 0.88 1.0 65 73.0 76 1.4 57 1.0 76 1.6 22 0.5 76.1 mm 3.000 3.00 3.30 2.25 2.4 3.00 3.8 76.1 76 1.5 57 1.1 76.2 1.7 - - 3 3.500 3.38 4.0 2.50 3.1 3.38 5.3 0.88 1.2 80 88.9 86 1.8 64 1.4 86 2.4 22 0.5 108mm 4.250 4.00 5.7 3.00 5.1 4.00 7.5 108.0 102 2.6 76 2.3 102 3.4 - - 4 4.500 4.00 6.7 3.00 5.6 4.00 8.7 1.00 2.4 100 114.3 102 3.0 76 2.5 102 1 3.9 25 1.1 5 5.563 4.88 12.6 3.25 8.3 4.88 15.7 1.00 4.1 125 141.3 124 5.7 1 83 3.8 124 7.1 25 1.9 139.7 mm 5.500 4.88 12.4 3.25 8.2 4.88 15.4 139.7 124.0 5.6 82.6 3.7 124.0 6.9 - - 159mm 6.250 5.50 12.6 3.50 9.2 5.50 17.9 158.8 140 5.7 89 4.2 140 8.0 - - 6 6.625 5.50 18.3 3.50 11.7 5.50 22.7 1.00 5.9 150 168.3 140 8.3 89 5.3 140 1 . 1 2.7 165.1 mm 6.500 5.43 17.6 3.50 11.4 5.50 22.0 165.1 139.7 7.9 88.9 5.2 139.7 9.9 - - 8 8.625 6.81 25.5 4.25 20.4 6.94 38.7 1.13 12.7 200 219.1 173 11.6 108 9.3 176 17.6 29 5.8 10.03 1539 Rev M Updated 12/2014 0 2014 Victaulic Company. All rights reserved. victaulic.com 2 4tauuic MechanicalT® STYLES 920 AND 920N Victaulic Mechanical-TO Outlet provides a direct branch connection at any location a hole can INS. - be cut in pipe. The hole is cut oversize to receive a "holefinder" locating collar which secures the outlet in position permanently. A pressure responsive gasket seals on the pipe O.D. Cross-type connections can be achieved by utilizing two upper housings of the same style and size, with the same or differing branch size connections. NOTE: Style 920 and Style 920N housings cannot be mated to each other to achieve a cross connection. Style 920 and Style 920N Mechanical-T outlets are available with grooved or female threaded STYLES 920 AND 920N outlet. Specify choice on order. Units are supplied painted with plated bolts. Galvanized hous- ings are available, supplied with plated bolts. All sizes of Style 920 and 920N are rated at 500 psi/3450 kPa working pressure on Schedule 10 and 40 carbon steel pipe. They may also be used on high density polyethylene or poly- butylene (HOPE) pipe. Pressure ratings on HDPE are dependent on the pipe rating. Contact Victaulic for ratings on other pipe. Style 920 and 920N are not recommended for use on PVC plastic pipe. Standard piping practices dictate that the Mechanical-T Styles 920 and 920N must be installed so that the main and branch connections are a true 90° angle when permanently attached to the pipeline surface. Additionally, the Vic-Tap Il® hole cutting tool, which allows for hole cutting capabilities on pressurized systems, utilizes the Style 920 Mechanical-I in conjunction with the Series 726 Vic-Ball Valve to create the Style 931 Vic-Tap II Mechanical-I unit. See page 8 for further information. STYLE 920 CROSS PATENTED MATERIAL SPECIFICATIONS Housing/Coating: Ductile iron conforming to ASTM A-536, grade 65-45-12, with orange enamel coating. Ductile iron conforming to ASTM A-395, grade 65-45-15, is available upon special request. Optional: Hot dipped galvanized Gasket: (Specify choice°) Grade "E" EPDM EPDM (Green color code). Temperature range —30°F to +230°F/-34°C to +110°C. Recommended for cold and hot water service within the specified temperature range plus a variety of dilute acids, oil-free air and many chemical services. UL Classified in accordance with ANSI/NSF 61 for cold +86°F/+30°C and hot +180°F/+82°C. NOT RECOMMENDED FOR PETROLEUM SERVICES. Grade 'T' nitrile Nitrile (Orange color code). Temperature range —20°F to +180°F/-29°C to +82°C. Recommended for petroleum products, air with oil vapors, vegetable and mineral oils within the specified temperature range. Not recommended for hot water services over +150°F/+66°C or for hot dry air over +140°F/+60°C. *Services listed are General Service Recommendations only. It should be noted that there are services for which these gaskets are not recommended. Reference should always be made to the latest Victaulic Gasket Selection Guide for specific gasket service recommendations and for a listing of services which are not recommended. Bolts/Nuts: Heat-treated plated carbon steel, trackhead meeting the physical and chemical requirements of ASTM A-449 and physical requirements of ASTM A-183. JOB/OWNER CONTRACTOR ENGINEER System No. Submitted By Spec Sect Para__________ Location Date Approved www.victaulic.com VIcrAuLIC IS REGISTERED TRADEMARK OF vIcTAuLic COMPANY C 2012 vICTAULIC COMPANY. ALL RIGHTS RESERVED. REV_M 4tauiicr 11.02_i CARBON STEEL PIPE - HOLE CUT PRODUCTS 11.02 Mechanical-I® Bolted Branch Outlets STYLES 920 AND 920N DIMENSIONS 6M&Rb I L lk MM _ -. . Y z 920N 500 1.50 2.00 1 2.53 1 1.61 1 5.35 2.75 3.1 v 50 15 3450 38.1 51 64 - 41 136 70 1.5 - 3K (a) 920N 500 1.50 1.97 2.53 I - 1.61 5.35 2.75 3.1 t 20 3450 38.1 50 64 41 136 70 1.5 - 1(a) a 920N 500 1.50 1.85 t 2.53 - 1.61 5,35 2.75 3.0 25 3450 38.1 47 64 41 136 70 1.4 - 1¼ (a) (a 920N 500 1.75 2.05 2.75 f 3.00 1.61 5.35 3.00 3.5 3.2 GROOVED OUTLET 32 3450 44.5 52 70 I 76 41 136 76 1.7 1.5 1½ (a) to 920N 500 1.75 2.03 2.75 3.12 1.61 5.35 3.25 3.6 3.2 40 3450 44.5 52 70 79 41 136 83 1.7 1.5 2112 ½ (a) §a 920N 500 1.50 2.21 2.74 1' 1.82 5.64 2.75 3.0 65 15 3450 38.1 56 70 4 - 46 143 70 1.4 - 14(a) fla 920¼ 500 1.50 2.18 2.74 I 1.82 5.64 2.75 3.0 20 3450 38.1 55 70 - 46 143 70 1.4 t 1¼ t (a) a 920N 500 1.75 20 3.00 . 3.25 1.82 6.29 3.00 3.5 3.2 - a 1(a) §a 92014 500 1.50 2.06 2.74 1 1.82 5.64 2.75 I 2.9 25 3450 38.1 52 70 4 - 46 143 70 1.4 - 32 3450 44.5 58 76 83 46 160 76 4 1.7 1.5 1 ½ t (a) U 500 2.00 2.28 3.00 3.25 1.82 6.26 3.25 3.6 3.3 I FEMALE THREADED OUTLET 40 920¼ 3450 50.8 58 76 83 46 159 83 1.7 j 1.6 t 300 1.50 2.22 2.75 2.25 6.46 3.18 3.9 76.1 x 920N - 15 2065 38.1 56 70 57 164 81 I 1.8 Provides a direct branch connection at 920N 300 1.50 2.19 2.75 2.25 6.46 3.18 + 39 - any location where a hole can be cut 20 2065 38.1 56 j 70 - . 57 164 81 1.8 in the pipe 1(a) 920N 300 1.50 2.07 I 2.75 2.25 6.46 3.18 ) 3.8 - 25 2065 381 53 70 57 164 81 1.7 A pressure responsive gasket provides 1¼ (a) U 920N 500 1.75 2.30 3.00 3.31 1.92 6.29 300 1 3.5 3.2 - the seal 32 3450 44.5 58 76 84 49 160 76 16 1.5 1½ (a) a 920¼ 500 2.00 2.28 3.00 3.31 1.92 6.29 3.25 3.5 3.3 Request Publication 11.03 for 40 3450 50.8 58 76 84 49 160 83 1.6 1.5 500 1.50 2.52 3.05 2.28 6.15 2.75 3.4 Mechanical-I cross assemblies ½ (a) U 920N 80 is 3450 381 64 78 - 58 j 156 70 16 - Pressure rated up to 500 psi/3450 kPa 14(a) a 920~ 500 1.50 2.49 3.05 2.28 6.15 1 2.75 3.4 - on steel pipe; also available for use 20 3450 38.1 63 78 - 58 4 156 70 1.6 with HDPE pipe 1(a) 920¼ 500 1.50 2.38 3.06 - 2.28 6.15 2.75 3.3 - 25 3450 38.1 61 78 ) 58 156 70 1.6 Sizes from 2 x 1/2750 x 15 mm 1¼ (a) to 92051 500 1.75 2.55 3.25 3.56 1 2.28 6.15 3.00 3.8 3.7 through 8 x 4/200 x 100 mm 32(b) 1 3450 44.5 65 83 90 I 58 156 76 1.8 1.8 1 ½ (a) to 1 500 2.00 2.78 3.50 3.56 2.28 6.15 3.25 4.1 I 3.8 40(b) 920N3450 50.8 71 89 90 58 156 83 1.9 4 1.8 2 (a) U 920N 500 2.50 2.75 3.50 3.56 2.28 6.75 3.88 4.9 4.6 50 3450 63.5 70 89 90 58 172 99 2.3 2.1 3½ 2 920N 500 2.50 3.00 3.75 2.44 6.72 3.88 3.8 90 >< 50 3450 63.5 76 - 95 62 171 99 - 1.8 IMPORTANT NOTES: TABLE CONTINUED ON PG. 3 Style 920 and Style 920N housings cannot be Center of run to engaged pipe end, female threaded outlet only (dimensions approximate). mated to one another t Available with grooved or female threaded outlet. Specify choice on order. to achieve cross connections. * Center of run to end of fitting. 1) Female threaded outlets are available to NPT and BSPT specifications. @ See page 7 for Fire Protection approvals and pressure ratings. (a) British Standard female pipe threaded outlet is available as listed. Specify "BSPT clearly on order. (b)For 76.1 mm threaded outlet, specify 21/Y BSPT clearly on order. § Vds approved for fire protection services a LPCB approved for fire protection services 0 Approved for use in China by Tianjin Approvals Company. www.victaulic.com ,4tauiicr vicTAuLic IS REGISTERED TRADEMARK OF VICTAIJLIC COMPANY. 02012 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 11.022 REVM DIMENSIONS GROOVED OUTLET FEMALE THREADED OUTLET Provides a direct branch connection at any location where a hole can be cut in the pipe A pressure responsive gasket provides the seal Request Publication 11.03 for Mechanical-T cross assemblies Pressure rated up to 500 psi/3450 kPa on steel pipe; also available for use with HDPE pipe Sizes from 2 x 1/2750 x 15mm through 8 x 4/200 x 100 mm a CARBON STEEL PIPE - HOLE CUT PRODUCTS 11.02 Mechanical-T® Bolted Branch Outlets STYLES 920 AND 920N Appr x. Dimensions Weight Each TT11- PG (am - cum (im -It TABLE CONTINUED FROM PAGE 2 4 1h (a) x 920 N 500 1.50 3.03 3.56 2.69 7.01 2.75 3.7 100 15 3450 38.1 77 90 J - £ 68 178 70 1.8 - ~ (a) 920N 500 1.50 3.00 3.56 2.69 7.01 2.75 3.7 20 3.450 38.1 76 90 - 68 178 70 1.8 - 1(a) 920N 500 1.50 288 3.56 2.69 7.01 2.75 3.6 25 3450 38.1 , 73 90 - 68 178 70 1.8 - 114(a) t 920N 500 1.75 3.08 3.78 4.00 2.69 7.01 3.00 4.0 3.6 32(b) 3.450 44.5 78 96 102 68 178 76 1.9 1.8 1 ½ (a) t 92 N 500 2.00 3.28 4.00 4.00 2.69 7.01 3.25 4.2 3.9 40(b) 3450 50.8 83 102 102 68 178 83 2.0 1.9 920 N 500 2.50 3.25 4.00 4.00 2.69 7.01 3.88 5.0 4.6 50 3450 63.5 83 102 102 68 178 99 2.3 2.1 21/2 (a) t 920 500 2.75 2.88 4.00 4.00 2.69 7.34 4.63 5.8 5.0 65 3450 69.9 73 102 102 68 186 J, 118 2.6 2.3 76.1 mm 920 500 2.75 2.88 4.00 2.69 7.34 I 4.63 6.4 3450 69.9 73 - 102 68 186 , 118 - 2.9 3(a) t 920 500 3,50 I 3.31 4.50 4.12 2.69 7.73 5.12 8.4 6.4 80 3450 88.9 84 114 105 68 196 130 1% (a( 920N 500 1.75 3.08 3.78 1 2.63 7.64 3.05 5.0 108.0 x 32 3450 44.5 78 96 £ 67 194 78 1 2.3 - 1 1/2 (a)o 920N 500 2.00 3.28 4.00 2.63 764 3.25 5.0 40 3450 50.8 83 102 - 67 194 83 2.3 - 2 (a) 920N 500 2.50 3.25 4.00 2.63 7.64 4.00 4.0 so 3450 63.5 83 102 + .. - 67 + 194 102 1.9 - 76.1 mm 920 500 2.75 2.88 I 4.00 I 4. 00 ' 2.63 7.64 4.29 8.0 7.8 3450 69.9 73 I 102 I 102 I 67 194 109 3.6 3.5 3 (a) 500 3.50 3.31 + I 4.50 t t 4.50 2.63 . 7.63 . 4.88 6.8 6.5 80 920 920 3450 500 88.9 2.00 84 4.03 114 4.75 114 + 67 I 4.75 1 3.16 194 9.70 124 3.69 31 7.4 3.0 7.6 5 1½ (a) t X 40 125 3450 50.8 102 121 121 80 246 94 3.4 3.4 2(a) 6 920 500 2.50 4.00 4.75 4.75 3.16 9.70 4.38 8.2 8.0 50 3450 63.5 102 121 121 80 246 111 3.7 3.6 21/2(a)f 500 2.75 3.63 4.75 4.75 3.16 9.70 4.63 8.3 7.9 65 920 3450 69.9 92 121 121 80 246 118 3.8 3.6 76.1 mm 920 500 2.75 3.75 4.75 3.16 t 9.70 4.63 8.0 3450 69.9 95 - j 121 80 246 118 - 36 3(a) 6 920 500 3.50 3.81 5.00 4.63 3.16 9.70 5.31 8.4 8.8 80 920N 3450 500 88.9 2.50 97 3.75 127 4.50 118 80 3.17 246 8.00 135 3.88 3.8 8.0 L 4.0 2 133.0 x so 3450 63.5 95 114 - 81 203 99 3.6 - I 3 920 500 3.50 3.81 I 5.00 3.00 9.46 5.31 8.0 80 3450 88.9 97 127 - 76 240 I 135 3.6 TABLE CONTINUED ON PG. 4 IMPORTANT NOTES: Center of run to engaged pipe end, female threaded outlet only (dimensions approximate). Style 920 and Style 920N housings cannot be 6 Available with grooved or female threaded outlet. Specify choice on order. mated to one another * Center of run to end of fitting. to achieve cross connections. A female threaded outlets are available to NPT and BSPT specifications. @ See page 7 for Fire Protection approvals and pressure ratings. (a) British Standard female pipe threaded outlet is available as listed. Specify "BSPT" clearly on order. (b)For 76.1 mm threaded outlet, specify 21/2" BSPT clearly on order. § Vds approved for fire protection services o -PCB approved for fire protection services 0 Approved for use in China by Tianjin Approvals Company. www.victaulic.com VICTAULIC is A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 02012 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REV..M jtauIicr 11.02_3 CARBON STEEL PIPE- HOLE CUT PRODUCTS 11.02 Mechanical-I® Bolted Branch Outlets STYLES 920 AND 920N DIMENSIONS FEMALE THREADED OUTLET Provides a direct branch connection at any location where a hole can be cut in the pipe A pressure responsive gasket provides the seal Request Publication 11.03 for Mechanical-T cross assemblies Pressure rated up to 500 psi/3450 kPa on steel pipe; also available for use with HDPE pipe Sizes from 2 x 1/2750 x 15 mm through 8 x 4/200 x 100 mm IMPORTANT NOTES: Style 920 and Style 920N housings cannot be mated to one another to achieve cross connections. OD DimensiDimensions • Weight Each~ TABLE CONTINUED FROM PAGE 3 1½ 920t N 500 200 378 450 330 823 325 70 - 139.7 40 3450 508 96 - 114 - 84 209 83 32 21' 920N 500 250 375 450 330 823 388 90 50 920N 3450 500 635 I.75 95 4.43 114 513 - 513 84 379 209 9.15 99 325 4.1 5.1 L - 4.8 6 1 V. (a) X 150 32 3450 445 112 130 130 96 232 83 23 2.2 1½ (a) + 920N 500 2.00 4.40 5.13 5.13 379 915 325 I s 5.1 40(b) 3450 50.8 112 130 130 96 232 83 24 2.3 920N 500 2.50 4.38 5.13 5.13 379 9.15 388 6.0 5.6 50 3450 63.5 111 130 130 96 232 99 2.7 4, 2 2½ 920 500 2.75 4.01 5.13 5.12 3.69 10.51 463 83 7.6 65 3450 69 - 110 4, 130 130 94 267 118 38 34 76.1 mm 920 500 2.75 4.15 5.21 3.69 10.51 463 84 3450 69.9 105 - 132 94 267 118 - 3.8 3(a) 1- 920 500 3.50 4.31 5.50 5.13 3.69 10.51 531 99 8.4 80 3450 88.9 110 140 .L 130 94 267 135 45 3.8 4(a) t 920 500 4.50 3.81 5.75 I 5.38 3.69 10.51 6.25 10.1 10.1 100 920N 3450 500 - 114.3 2.00 - 97 4.41 146 5.13 137 94 3.63 267 9.40 159 3.25 4.6 7.8 4 1 ½ (a) 1590 x 40 3450 50.8 4 112 130 - 92 239 83 3.5 - 2(a) 20N 500 2.50 4.38 5.13 3.63 9.40 3.88 8.0 t 50 3450 63.5 111 130 - 92 239 99 -3.6 - 76.1 mm 920 500 2.75 4.38 5.50 5.13 3.63 9.40 4.63 9.5 9.5 3450 69.9 111 140 130 92 239 118 4.3 4.3 3 920 500 3.50 4.31 5.50 5,13 3.63 9.40 5.31 8.1 14.0 80 3450 88.9 110 140 130 92 239 135 3.7 64 108.0mm 920 500 4.50 4.45 5.38 3.63 9.40 6.12 10.0 3450 1143 13 - - 137 92 239 155 - -- 920 500 4.50 3.81 1 5.5 3.63 9.40 6.25 18.0 100 3450 114.3 96.80 146 1 92 239 159 I 8.2 1 - TABLE CONTINUED ON PG. 5 .... Center of run to engaged pipe end, female threaded outlet only (dimensions approximate). 'I' Available with grooved or female threaded outlet. Specify choice on order- * Center of run to end of fitting. 8 Female threaded outlets are available to NPT and BSPT specifications. @ See page 7 for Fire Protection approvals and pressure ratings. (a) British Standard female pipe threaded outlet is available as listed. Specify "BSPT clearly on order. (b)For 76.1 mm threaded outlet, specify 21/2' BSPT clearly on order. § Vds approved for fire protection services LPCB approved for fire protection services 0 Approved for use in China by Tianjin Approvals Company. www.victaulic.com vIcTAULIC IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2012 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 11.024 \%taulicf REV_M CARBON STEEL PIPE - HOLE CUT PRODUCTS 11.02 Mechanical-I® Bolted Branch Outlets STYLES 920 AND 920N DIMENSIONS GROOVED OUTLET FEMALE THREADED OUTLET Provides a direct branch connection at any location where a hole can be cut in the pipe A pressure responsive gasket provides the seal Request Publication 11.03 for Mechanical-T cross assemblies Pressure rated up to 500 psi/3450 kPa on steel pipe; also available for use with HDPE pipe Sizes from 2 x 1/2750 x 15 mm through 8 x 4/200 x 100 mm le Size No. I Max,Work Pressure@~ Dimensions . Approx.;. ch __ • L'T. TABLE CONTINUED FROM PAGE 4 1 920N 500 1 150 1 388 456 379 934 I 275 8.0 1651 x 25 3450 381 99 116 - 96 237 j, 70 3.6 - 1%n 920½ 500 175 443 513 - 379 934 325 8,4 - 32 3450 445 113 + 130 ,j - 96 237 ,j 83 3.8 1½ (a) '('a 920½ 500 200 441 5.13 5.13 379 934 3.25 8.4 54 40 3450 50.8 112 T 130 130 96 237 83 3.8 2.4 6.0 2(a) 1' 920N 500 2.50 4.38 5.13 5,13 379 934 388 8.5 50 3450 63.5 111 f 130 130 96 237 99 3.9 2.7 76.1 mm 920 500 2.75 4.01 5.13 5.21 3.63 1081 4.63 8.6 1 7.6 3450 69.9 110 130 132 92 267 ,, 118 5.31 3.9 j, 10.2 3.4 8.4 3(a) 5 a 920 500 3.50 4.31 5.50 5.13 3.63 10.51 80 3450 88.9 110 140 130 92 135 4.6 , 3.8 4(a) to 920 500 4.50 3.81 5.75 5.38 3.63 10.51 6.25 10.5 8.4 100 920 3450 500 3450 114.3 2.75 69.9 97 5.44 138 146 6.19 157 137 92 267 6.25 4.81 12.42 159 122 316 159 4.50 114 4.8 11.6 5.3 [3.8 11.6 5.3 8 x 2 )a)t 200 50 21/2 (a) 5 65 920 500 3450 2.75 69.9 5.07 129 6.19 157 6.19 I 4.81 12.42 157 122 , 316 t 4.50 114 11.6 5.3 11.6 5.3 76.1 mm 920 500 2.75 5.25 I I 6.25 4,81 12.42 4.56 11.6 3450 69.9 133 - 159 122 316 116 - 1 T 1 5 3(a) to 920 500 3.50 5.31 '[ 6.50 6.50 4.81 12.42 5.31 12.6 J 11.6 80 3450 88.9 135 165 165 j, 122 316 1 135 57 15.3 4(a) to 920 500 4.50 4.81 i 6.75 6.38 4.81 12.42 6.25 15.3 12.5 100 3450 114.3 122 171 162 122 I 316 159 6.9 5.7 Center of run to engaged pipe end, female threaded outlet only (dimensions approximate). t Available with grooved or female threaded outlet. Specify choice on order. * Center of run to end of fitting. 8 Female threaded outlets are available to NPT and BSPT specifications. @ See page 7 for Fire Protection approvals and pressure ratings.' British Standard female pipe threaded outlet is available as listed. Specify "BSPT clearly on order, For 76.1 mm threaded outlet, specify 21/2" BSPT clearly on order. § Vds approved for fire protection services n -PCB approved for fire protection services 0 Approved for use in China by Tianjin Approvals Company. IMPORTANT NOTES: Style 920 and Style 920N housings cannot be mated to each other to achieve cross connections. www.victaulic.com VICTAULIC IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2012 VICTAULIC COMPANY. ALL RIGHTS RESERVED, REVM tauIid 11.025 CARBON STEEL PIPE - HOLE CUT PRODUCTS 11.02 Mechanical-I® Bolted Branch Outlets STYLES 920 AND 920N FLOW DATA Flow test data has shown that the total head loss between point (1) and (2) for the Style 920, 920N and 929 Mechanical-TO fittings can best be expressed in terms of the pressure difference across the inlet and branch. The pressure difference can be obtained from the relationship below. Cv and Ky Values Values for flow of water at +60°F/+16°C are shown in the table below. Formulas for C5 1K Values: ( AP =Q Where: AP Where: k Q = Flow (GPM) K Q = Flow (m3lh) 0 Drop (psi) Q = Q K 5P=Pressure — = AP Pressure Drop (bar) K=FlowCoefficiera Exaggerated for clarity Equivalent Length of Outlet Size Schedule 40 Carbon Steel Pipe ii ½ OUTLET SIZE (C 120)t FT 1 0.840 - 2 - C,/K, Values 11 15 21,3 , 9.4 1.050 - 4 13.7 16 26.7 - 8 - 1 25 33.7 - 18 1¼ 1.660 5½ 6 50 48 32 42.7 42.9 41.1 1 ½ - ' 1.900 11 53 4 53 40 98.3 . 454 j 45.4 2 2.375 112 j 104 12 60.3 . so 89.1 t 150 21/, 2.875 20 12 1/2 119 65 73.0 102 , 128.5 761mm 3.000 16 161 761 1381 3.500 14 ½ 249 237 80 88.9 213.4 203.1 4.500 20 22 421 401 100 114.3 360.8 I 343.6 O Hazen-Williams coefficient of friction is 120. Pipe with a wall thickness of 0.165in 14.2mm. www.victaulic.com VICTAULIC IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2012 VICTAULIC COMPANY. ALL RIGHTS RESERVED. 11.02.6 \JtauIic REVM CARBON STEEL PIPE - HOLE CUT PRODUCTS 11.02 Mechanical-T® Bolted Branch Outlets STYLES 920 AND 920N FIRE PROTECTION APPROVALS AND PRESSURE RATINGS The information provided below is based on the latest listing and approval data at the time of publication. Listings/Approvals are subject to change and/or additions by the approvals agencies. Contact Victaulic for performance on other pipe and the latest listings and approvals. rn .BM IL as= L am iL __________ _____ _am= _il _____ 21/2 -6 2.875 - 6.625 A 10 40 400 400 400 290 I 232 362 65-150 730-168.3 2.875 -4500 All J DF 2755 1 300 2755 300 2755 300 1999 290 1599 232 2495 362 21/2 - 4 65-100 73.0-114.3 2.875 - 4.500 All SF 2065 300 2065 300 2065 I 300 1999 290 1599 232 2496 362 21/2 -4 65 7 100 730 1143 6.625 10 2065 300 2065 300 2065 I 250 1999 290 4 1599 232 2496 362 6 150 168.3 2065 2065 1724 1999 I 1599 2496 6 6.625 34 3040 300 300 300 290 232 362 150 168.3 +1 2065 2065 2065 1999 1599 2496 8 8.625 21/2 1040 400 - 1 - - 145 - 200 219.1 i 8.625 3 10 2755 300 -I. - I 250 - 1000 145 - 8 200 219.1 + 8.625 34 I t 30 40 2065 300 - . 1724 t 300 - -F I 1000 145 T - 8 200 219.1 i 2065 2065 1000 NOTES: 10 refers to Listed/Approved Schedule 10 steel sprinkler pipe. 40 refers to Listed/Approved Schedule 40 steel sprinkler pipe. DF refers to Listed/Approved Dyna-Flow steel sprinkler pipe manufactured by American Tube Company. SF refers to Listed/Approved Super-Flo steel sprinkler pipe manufactured by Allied Tube and Conduit Corporation VIC-TAP II HOLE CUTTING TOOL FOR The Vic-Tap II hole cutting tool is designed for use with the Style 931 Vic-Tap II Mechanical-T unit, 4 - 8/100 - 200 MM CARBON STEEL PIPE which is a combination of the Style 920 Mechanical-T and Series 726 Vic-Ball Valve. The Vic-Tap II is capable of tapping into carbon steel pipe systems under pressures up to 500psi/3450kPa. The Style 931 Vic-Tap II Mechanical-T unit is a full port ball valve which can be mounted on 4/100mm, 57125mm, 6/150mm and 8'7200 mm diameter pipe. The Style 931 comes with a 21/2 /65mm grooved outlet. The drill motor is an electric motor with ground fault circuit interrupter (GFCI) in accordance with - safety codes. For more information, refer to publication 24.01. www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2012 VICTAULIC COMPANY. ALL RIGHTS RESERVED. REV...M \4taulicr 11.027 Mechanical-I® STYLES 920 AND 920N INSTALLATION Reference should always be made to the 1-100 Victaulic Field Installation Handbook for the product you are installing. Handbooks are included with each shipment of Victaulic products for complete installation and assembly data, and are available in PDF format on our website at www.victaulic.com. WARRANTY Refer to the Warranty section of the current Price List or contact Victaulic for details. NOTE This product shall be manufactured by Victaulic or to Victaulic specifications. All products to be installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations. For complete contact information, visit www.victaulic.com 11.02 1480 REV M UPDATED 03/2012 ActauIi VICTAULIC IS REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2012 VICTAULIC COMPANY. ALL RIGHTS RESERVED. X. 11.02_L i: SIGMA Quality - Service - Commitment - Delivered. ng~ Malleable Threaded Fittings ALL MALLEABLE THREADED FITTINGS MANUFACTURED FOR AND BY SIGMA PIPING PRODUCTS CONFORM TO, COMPLY WITH, AND ARE MANUFACTURED TO THE FOLLOWING STANDARDS: ASTM A 197- Standard Spec for Cupola Malleable Iron ASTM A 153- Standard Spec for Zinc Coating (Hot Dip) on Iron and Steel ANSI B 16.3- Malleable Iron Threaded Fittings Classes 150 ANSI/ASME 131.20.1- Pipe Threads, General Purpose (Inch) NPT Ductile Iron Threaded Fittings ALL DUCTILE IRONS MANUFACTURED FOR AND BY SIGMA PIPING PRODUCTS CONFORM TO, COMPLY WITH, AND ARE MANUFACTURED TO THE FOLLOWING STANDARDS: ASTM A 536- Grade 65-45-12 ASME B 16.3- Ductile Iron Threaded Fittings Classes 150 ANSI/ASME BI.20.1- Pipe Threads, General Purpose (Inch) NPT Cast lronThreaded Fittings ALL CAST IRONS MANUFACTURED FOR AND BY SIGMA PIPING PRODUCTS CONFORM TO, COMPLY WITH, AND ARE MANUFACTURED TO THE FOLLOWING STANDARDS: ASTM A 128- Class B Standard Spec for Cupola Cast Iron ANSI B 16.4- Cast Iron Threaded Fitting Classes 125 ANSI/ASME 13I.20.1- Pipe Threads, General Purpose (Inch) NPT Steel Pipe Nipples ALL STEEL PIPE NIPPLES MANUFACTURED FOR AND BY SIGMA PIPING PRODUCTS CONFORM TO, COMPLY WITH, AND ARE MANUFACTURED TO THE FOLLOWING STANDARDS: ASTM A 53- Standard Spec for Pipe, Steel, Black and Hot-Dipped, Zinc Coated, Welded and Seamed ANSI/ASME BI.20.1- Pipe Threads, General Purpose (Inch) NPT www.sigmaco.com O Dimensions: ANSI B16.3 CLASS 150 [1 Coating: Black- none; Galvanized- Hot Dip per ASTM A153 O Material: Malleable iron per ASTM Al 97 []Threads: Pipe Threads, General Purpose ASME B1.20.1 Description F 1 Malleable Threaded 90 I 11EMCODE I[DIMENSIUNII ITEM LSMElI BLACK IflGALV It A II B I WEIGHT A 3/8" 1M90B0303 1M90B0303G 0.95 0.95 017 - 1/2" 1M90B0404 1M90B0404G 1.12 1.12 0.30 3/4" 1M90B0505 1M90B0505G 1•31L 1.31 0.45 1" 1M90B0606 1M90B0606G 1.50 1.50 0.73 1 1/4" 1M90B0707 1M90B0707G 1.75 1.75 0.97 11/2" 1M90B0808 1M90B0808G 1.94 1.94 1.30 2" 1M90B0909 1M9080909G 2.25 2.25 2.06 2 1/2" IM90BI0I0 IM90BI01OG 2.79 2.70 3.55 3" IM9OBIIII IM9013I1IIG 3.08 3.08 5.46 LISTED 4" 1M90B1212 1M90131212G 3.79 3.79 8.95 Description I I Malleable Threaded 45 L ITEMICQDE ]EDIMENSIUNJ iTEM I SIZE II BLACK II GAIN 11 A IEB1I WEIGHT 3/8" 1M45B0303 1M45B0303G 0.80 0.80 0.16 A 1/2" 1M45B0404 1M45B0404G 0.88 0.88 0.22 i 3/4" 1M45B0505 1M45B0505G 0.98 0.98 0.37 1" 1M45B0606 1M45B0606G 1.12 1.12 0.54 1 1/4" 1M45B0707 1M45B0707G 1.29 1.29 0.86 1 1/2" 1M45B0808 1M45B0808G 1.43 1.43 1.13 2" 1M45B0909 1M45B0909G 1.68 1.68 1.79 2 1/2" 1M45B1010 1M45B1010G 1.95 1.95 2.78 3" 1M45131111 1M45B1111G 2.17 2.17 4.48 LISTED 1M45B1212 1M45B1212G 2.61 2.61 7.40 Description 1 1 I ITEM CODE IEDIMENSIONi ITEM z [BjCX1[ 1[jS 1 WEIGH Malleable Thretreet ed9O 3/8" 1M90S0303 1M90S0303G 0.80 1.00 0.17 1/2" 1M90S0404 1M90S0404G 0.88 1.13 0.24 3/4" 1M9050505 1M90S0505G 1.00 1.31 0.41 1M90S0606 1M90S0606G 1.23 1.44 0.62 / 1 11/4" 1M9050707 1M90S0707G 1.31 1.69 1.09 B I LA 11/2" 1 M90S0808 I M90S0808G 1.44 1.88 1.44 1M90S0909 1M90S0909G 1.69 2.25 2.85 --i LISTED - Description F I NOM I 1ThMQDE Il IThM Malleable Hex Nut SIZE LBLACK it GALV ii WEIGHT 1/2" IMLN04 1MLN04G 0.12 3/4" IMLNOS IMLN05G 0.22 /1 \\ 1" 1MLN06 IMLN06G 038 \ l,, ) J 1 1/4" IMLN07 IMLN07G 0.58 0.73 1 1/2" :: :: 1.13 LISTED www.sigmaco.com Malleable Threaded Fitt Description I I ITEM cODE. ][DMENS]flNT]I ITEM BLACK 1 F A 11 IWEIGH Malleable Redung t I NOM SIZj1 Ben E 11 1/2" X 3/8" 1M90R0403 1M90R0403G 1.00 1.06 0.22 B 3/4" X 1/2" 1M90R0504 1M90R0504G 1.19 1.25 0.38 1" X 1/2" 1M90R0604 1M90R0604G 1.25 1.38 0.46 X 3/4" 1M90R0605 1M90R0605G 1.38 1.44 0.56 j 1 1/4"X 1/2" 1M90R0704 1M90R0704G 1.38 1.56 0.61 I I A 11/4" X 3/4" 1M90R0705 1M90R0705G 1.44 1.63 0.71 / 11/4" X 1" 1 M90R0706 I M90R0706G 1.44 1.66 1.15 f ( 11/2" X 1/2" 1M90R0804 1M90R0804G 1.41 1.66 1.15 11/2" X 3/4" 1M90R0805 1M90R0805G 1.50 1.75 1.08 1 1/2"X 1" 1M90R0806 1M90R0806G 1.63 1.81 1.02 UL 11/2" X 11/4"•• 1M90R0807 1M90R0807G 1.81 1.88 1.17 LISTED 2" X 1/2" 1M90R0904 1M90R0904G 1.49 1.88 1.30 X 3/4" 1 M90R0905 1 M90R0905G 1.63 2.00 1.30 2"X 1" 1 M90R0906 I M90R0906G 1.75 2.00 1.35 2" X 1 1/4" 1M90R0907 1M90R0907G 1.88 2.13 1.53 2"X 1 1/2" 1M90R0908 1M90R0908G 2.00 2.13 1.75 NUM L ITEM CDTDE 1[DIM 1[ ITEM I SIZE I BLACK II GALV lEAil WEIGHT 1/4" 1MT020202 1MT020202G 0.81 0.15 3/8" 1MT030303 1MT030303G 0.94 0.23 1/2" 1M1040404 1MT040404G 1.13 0.41 3/4" 1MT050505 1MT050505G 1.31 0.60 1" 1MT060606 1MT060606G 1.50 0.90 1 1/4" 1MT070707 1M1070707G 1.75 1.31 1 1/2" 1MT080808 1MT080808G 1.94 1.73 2" 1MT090909 1MT090909G 2.25 2.52 2 1/2" IMTIOIOIO 1MT101010G 2.69 4.90 3" 1MT111111 IMTII1IIIG 3.06 7.13 4" 1MT121212 1MT121212G1 3.81 11.32 Description F Malleable Threaded Tee j LISTED Description I Malleable Threaded Cross I. k, Is]1 1 111111111111ft-:W,tSiII IU)T M1I' IIIIIIIIIIIIIIII w1i W i%1 1/2" 1MX04 IMX04G 1.12 0.42 3/4" IMX05 IMX05G 1.13 0.69 1" IMX06 IMX06G 1.50 1.12 11/4" IMX07 IMX07G 1.75 1.44 11/2" 1 MX08 I MXO8G 1.94 1.98 1MX09 IMXO9G 2.25 3.30 UL 2 1/2" 1MXI0 IMXIOG 2.70 5.90 IMX1I IMXIIG 3.08 13.50 LISTED www.sigmaco.com Malleable Threaded Description I Malleable Reducing Tee LISTED NOM IIhMDE 1L_LliMEN I ITEM [LACK1E3ALV IEA ][B11 C ii 1/2"X 1/2"X 3/8" 1MT040403 1M1040403G 1.06 1.06 1.06 0.30 3/4"X 1/2"X 1/2" 1MT050404 1MT050404G 1.08 1.08 1.09 0.38 3/4" X 1/2" X 3/4" 1MT050405 1MT050405G 1.11 1.11 1.13 0.46 3/4" X 3/4" X 1/2" 1MT050504 1MT050504G 1.19 1.19 1.25 0.47 1"X 1/2" X 1/2" 1MT060404 1MT060404G 1.21 1.21 1.30 0.58 1" X 3/4" X 1/2" 1MT060504 1MT060504G 1.22 1.22 1.32 0.59 1" X 3/4'X 3/4" 1MT060505 1MT060505G 1.23 1.23 1.33 1.59 1" X 1" X 1/2" 1MT060604 1M1060604G 1.25 1.25 1.38 0.70 1"X 1" X 3/4" 1MT060605 1MT060605G 1.38 1.38 1.44 0.82 11/4" X 1" X 1" 1M1070606 1MT070606G 1.56 1.56 1.69 1.10 1 1/4" X 1 1/4" X 1/2" 1M1070704 ,1MT070704G 1.38 1.38 1.56 0.98 1 1/4" x 1 1/4" X 3/4" 1MT070705 1M1070705G 1.40 1.40 1.60 0.94 11/4 X 11/4 X 1 1MT070706 1MT070706G 1.56 1 56 169 1.20 11/2" X 11/4" X 1" 1MT080706 1M1080706G 1.63 1.63 1.81 1.30 1 1/2" X 11/2" X 1/2" 1MT080804 1MT080804G 1.44 1.44 1.69 -: 1.19 11/2" X 11/2" X 3/4" 1M1080805 1MT080805G 1.50 1.50 1.75 1.30 11/2" X 11/2" X 1" 1MT080806 :1MT080806G, 1.63 1.63 1.81 1.45 11/2" x 11/2" x 11/4" 1MT080807 1MT080807G 1.81 1.81 1.88 1.52 2" x 2' x 1/2" 1MT090904 1MT090904G 1.50 1.50 1.88 1.65 2" x 2" X 3/4" 1M1090905 1MT090905G 1.63 1.63 2.00 1.87 2" X 2"X 1" 1MT090906 1MT090906G 1.75 1.75 2.00 1.76 2"x2"x 11/4" 1MT090907 1MT090907G 1.88 1.88 2.13 2.35 2" x 2" x 1 1/2" 1MT090908 1MT090908G 2.00 2.00 2.19 2.55 2 1/2" X 2 1/2" x 1" IMTI01006 IMT101006G 1.88 1.88 2.38 2.85 2 1/2" x 2 1/2" x 11/4" 1MT101007 !1MT101007G 2.06 2.06 2.44 1' 3.36 21/2X21/2X11/2 1MT101008 1MT101008G 2.19 2.19 2.50 3.46 2 1/2" x 2 1/2" X 2" 1MT101009 IMT101009G 2.38 2.38 2.62 3.65 3"x 3"X 1/2" 1M1111104 1MT111104G 1.76 1.76 2.52 4.03 3" X 3" X 3/4" 1MT111105 1MT111105G 1.88 1.88 1.63 4.03 3" X 3"X I" 1MT111106 1MT111106G 2.00 2.00 2.62 4.13 3"X3"X 11/4" 1M1111107 IMTI111O7G 2.19 2.19 2.75 4.50 3"X3"X 11/2" 1MT111108 1MT111108G 2.31 2.31 2.81 5.18 3"X3"X2" IMT111109 1MT111109G 2.50 2.50 2.88 5.70 3" X 3" X 11/2" 1MTIIIIIO 1MT111110G 2.57 2.57 2.89 5.00 4" X 4" X 1 1/4" 1MT121207 1M71212076 2.39 2.39 3.26 7.47 4" X 4" x 11/2" 1MT121208 IMT111208G 2.51 2.51 3.32 7.47 4" x 4"X 2" 1MT121209 1MT121209G 2.75 2.75 3.44 8.39 4" x 4" x 2 1/2" 1MT121210 IMT12121OG 2.75 2.75 3.44 7.70 4 X4 X3 1M1121211 1MT1212116 331 331 363 893 [NUM 1 ITEM CODE I iTEM I SIZE I BLACK 11 GAW WEIGHT 1/2" IMK04 IMKO4G 0.14 3/4" 1MKO5 1MK05G 0.21 1" IMKO6 IMK06G 0.37 1 1/4" 1MK07 IMK07G 0.58 1 1/2" 1MK08 IMK08G 0.74 2" 1MK09 IMK09G 0.94 2 1/2" IMKlO IMK10G 1.60 3" IMKII 1MK1IG 2.79 4" lMK12 IMKI2G . 3.66 Description I Malleable Cap I LISTED www.sigmaco.com Malleable Threaded Description I I Malleable Coupling I ITEM- DE IIflIMiF7TEW7 SIZE I BLACK]I GAUl II A I WEIGHT 3/8" 1MCP0303 IMCPO3O3G 1.18 0.13 1/2" IMCP0404 IMCP0404G 1.31 0.20 3/4" 1MCP0505 IMCP0505G 1.50 0.30 1" IMCP0606 IMCP0606G 1.69 0.48 1 1/4" IMCP0707 1MCP0707G 1.93 0.75 11/2" IMCP0808 IMCPO8O8G 2.13 1.00 2" 1MCP0909 1MCPO9O9G 2.50 1.45 2 1/2" IMCPI010 1MCP1010G 2.88 2.40 3" IMCPIIII IMCPII1IG 3.19 330 4" IMCPI2I2 IMCP12I2G 3.69 5.72 LISTED Description I Malleable Reducing Coupling 11 I® LISTED NOM SIZE I ITEMCOflE I[DIM.. I ITEM [BLACKjI GALV IL A jI WEIGHT 1/2" X 3/8" 1MCR0403 1MCRO403G 0.17 0.17 3/4" X 1/2" IMCR0504 IMCRO504G 0.27 0.27 1" X 1/2" 1MCRO604 1MCRO604G 0.39 0.39 1" X 3/4" IMCRO605 IMCR0605G 0.43 0.43 1 1/4" X 1/2" 1MCR0704 IMCR0704G 0.61 0.61 1 1/4" X 3/4" IMCR0705 IMCR0705G 0.64 0.64 1 1/4"X 1" 1MCR0706 1MCR0706G 0.68 0.68 1 1/2"X 1/2" IMCRO804 IMCR0804G 0.78 0.78 1 1/2"X 3/4" IMCRO805 IMCRO805G 0.88 0.88 1 1/2"X 1" IMCRO8O6 IMCRO806G 0.88 0.88 11/2" X 11/4" IMCR0807 IMCRO8O7G 0.90 0.90 2"X 1/2" 1MCRO904 1MCRO9O4G 1.15 1.15 2" X 3/4" 1MCRO905 1MCRO905G 1.34 1.34 2"X 1" 1MCRO906 1MCRO9O6G 1.40 1.40 2" X 11/4" IMCRO907 IMCRO907G 1.53 1.53 2"X 11/2" IMCRO908 IMCRO908G - 1.55 1.55 2 1/2"X 1 1/4" 1MCR1007 IMCR1007G 2.09 2.09 2 1/2" X 1 1/2" IMCR1008 IMCRI008G 2.09 2.09 2 1/2"X 2" 1MCRI009 1MCR1009G 2.51 2.51 3" X 11/4" IMCRII07 IMCRII07G 2.99 2.99 3"X 1 1/2" IMCR1108 1MCR11O8G 3.30 3.30 3" X 2" 1MCRII09 IMCRII09G 3.25 3.25 3" X 2 1/2" 1MCR1II0 IMCRI1IOG 3.29 3.29 4"X 11/2" IMCRI208 IMCR1208G 4.90 4.90 4" X 2" 1MCRI209 'IMCR1209G 5.10 5.10 4"X2 1/2" 1MCR1210 1MCR121OG 6.55 6.55 4"X 3" IMCRI21I 1MCR12116 4.04 404 [11UM]L ITEM IQDE I1 DIMENSIN1I ITEM I SIZE Ii ULACK II GALV 1LA 1LW1L WEIGHT 1/2" IMFF04 1MFF04G 3.50 2.50 0.56 3/4" IMFF05 IMFF05G 3.50 2.50 0.60 1MFF06 IMFF06G 4.00 3.0 0.84 1 1/4" 1MFF07 1MFF07G 4.00 3.00 0.90 1 1/2" IMFF08 IMFF08G 4.50 3.50 1.20 IMFF09 IMFF09G 5.50 4.25 2.03 Description I I Malleable Floor Flange _-_ B _........ I I ___A LISTED www.sigmaco.com Malleable Threaded Description I Malleable Plug I to lz . I - W@ LISTED I .ITEM- I ITEM SIZE Bl.ACIJI GALV II WEIGHT 3/8" 1MPLGO3 IMPLG03G 0.06 1/2" 1MPLG04 IMPLG04G 0.10 3/4" 1MPLG05 1MPLG05G 0.17 1" 1MPLG06 IMPLG06G 0.28 1 1/4" IMPLG07 IMPLG07G 0.44 1 1/2" 1MPLGO8 1MPLG08G 0.62 2" : IMPLGO9 IMPLGO9G 0.91 2 1/2" 1MPLG10 1MPLG1OG 1.05 3" 1MPLG11 1MPLG11G 1.70 4" 1MPLGI2 IMPLGI2G 3.00 Description I I Malleable Bushings =-WF,:4mQw j,1!jI 1/2" X 1/4" IMBSH0402 IMBSH0402G 0.06 1/2" X 3/8" IMBSI-10403 1MBSH0403G 0.05 3/4"X 1/2" 1MBSH0504 IMBSH0504G 0.11 1" X 1/2" IMBSH0604 IMBSH0604G 0.21 1" X 3/4" IMBSH0605 1MBSH0605G 0.17 1 1/4"X 1/2" IMBSH0704 IMBSH0704G 0.34 1 1/4" X 3/4" 1MBSH0705 IMBSH0705G 0.31 1 1/4"X 1" 1MBSH0706 1MBSH0706G 0.26 UL 1 1/2"X 1/2" IMBSH0804 I 1MBSH0804G 0.48 ISTED 1 1/2"X 3/4" IMBSH0805 1MBSH0805G 0.48 1 1/2" X 1" 1MBSH0806 IMBSH0806G 0.43 1 1/2" X 1 1/4" IMBSH0807 IMBSH0807G 0.30 2" X 1/2" IMBSH0904 IMBSH0904G 0.65 2" X 3/4" IMBSH0905 1MBS1-10905G 0.83 2" X 1" IMBSH0906 IMBSHO9O6G 0.78 2"X 1 1/4" IMBSH0907 1MBSH0907G 0.73 2" X 1 1/2" IMBSH0908 1MBSH0908G 0.60 2 1/2" X 11/4" 1MBSHI007 1MBSH1007G 1.30 2 1/2" X 11/2" 1MBSH1008 IMBSHI008G 1.20 2 1/2" X 2" 1MBSH1009 1MBSH1009G 0.90 3" X 1 1/4" 1MBSH1I07 IMBSH1107G 2.50 3" X 11/2" IMBSHI108 IMBSHI108G 2.30 3"X2" IMBSH1109 1MBSH1109G 2.00 3" X 2 1/2" 1MBSH1110 1MBSH1110G 1.60 4"X 1 1/4" IMBSH1207 IMBSHI207G 3.20 4"X 1 1/2" IMBSH1208 IMBSF4I208G 3.30 4" X 2" IMBSH1209 1MBSH1209G 3.10 4"X 2 1/2" 1MBSH1210 IMBSFI12IOG 3.80 4"X3" IMBSHI2II 1MBSH1211G , 3.00 www.sigmaco.com Malleable Threaded Description I FIqUNr-1 I IThM GDDE IIIIMiI ITEM Malleable Union I. SIZE I BLACK 11 GALVIL ILWEIGHT 1/4" IMUN02 1MUN02G 1.81 0.45 A 3/8" 1MUN03 IMUN03G 1.81 0.42 1/2" 1MUN04 IMUN04G 1.94 0.44 3/4" IMUN05 IMUN05G 2.06 0.60 IMUNO6 IMUN06G 2.44 0.91 1 1/4" IMUN07 1MUN07G 2.63 1.45 I 1 1/2" 1MUN08 IMUNO8G 2.75 1.69 1MUN09 IMUN09G 2.94 2.46 " IMUNIl 1MUN11G 3.63 4.95 LISTED 4" IMUNI2 IMUN12G 3.75 8.75 Description I I ENOM1[ ITEM CiODE IFDIMJ ITEM Malleable Union WI Brass Seat I SIZE II BLACK II GALV II A II WEIGHT 1/4" 1MUNBS02 1MUNBS02G 1.81 0.45 A 3/8" IMUNBS03 IMUNBS03G 1.81 0.42 1/2" IMUNBS04 IMUNBS04G 1.94 0.44 3/4" IMUNBS05 1MUNBS05G 2.06 0.60 1MUNBS06 IMUNBS06G 2.44 0.91 1 1/4" IMUNBS07 IMUNBS07G 2.63 1.45 I 1 1/2" 1MUNBS08 IMUNBSO8G 2.75 1.69 I Ui. IMUNBS09 IMUNBS09G 2.94 2.46 " 1MUNBS11 1MUNBS11G 3.63 4.95 LISTED 4" IMUNBSI2 IMUNBSI2G 3.75 8.75 Description' NONE I ITEM COIDE IIIDIM. I ITEM L SIZE W S LBLACKIL GALVII A I EIGHT Malleable Extension 1/2" IMEX04 i. 1MEX04G 1.95 7.32 LISTED www.sigmaco.com I I Oil 111IN s 0 O Notice: D.I. Fittings have higher tensile strength then o D.I. Threaded fittings are UL, cUL listed and Factory Mutual that of steel pipe, over tightening can cause damage approved for 500psi servce. D. 1. Per ASTM A 536 grade 6545- to pipe threads which may cause leakage. D.I. Fitting 12. Dimensions conform to ANSI B16.3 Class 150. Threads are should be tightened three turns beyound hand tighten, NPT per ANSI/ASME 13I.20.1 no more than four turns. Description I D. 1. 90 Degreed Elbow B Um r --~[ I a> NOM SIZE IlTEM ITEM 1 I BLACK II A II B II&EIGHII 11)90130606 1.50 1.50 0.62 1 1/4" 1090B0707 1.75 1.75 0.90 1 1/2" 11)90130808 1.94 1.94 1.20 1D90B0909 2.25 2.25 1.85 Description F 0.1. Straight Tee Al A Ulm O M SIZE ILITEM COtJE1FflIMENS]iff][1TEM N I__it BLACK1EA 1EBNE1GH 1DT060606 1.50 1.50 0.85 1 1/4' 1D1070707 1.75 1.75 1.22 1 1/2" 10T080808 1.94 1.94 1.55 1DT090909 2.25 2.25 2.45 Description F D.I. Coupling c®us LWED DTEWCODEI IIDIMJ NOM SIZJ1 [1TEM BLACK lEA 1NEIGH11 IDCP0606 1.50 0.85 1 1/4" 1DcP0707 1.75 1.22 11/2" IDCP0808 1.94 i1 1.55 IDCP0909 2.25 2.45 Description 1 D.I. Red. 90 Deg. Elbow OM SIZE ' EMcoDE1uuMNsIuff:1I ITEM I BLACK IEA ][B7jEIGH 1 X1/2" 1D90R0604 1.26 1.36 0.44 I X 3/4" 1D90R0605 1.37 1.45 0.52 1 1/4X 1/2" 1D90R0704 1.34 1.53 0.64 1 1/4 X 3/4" 1090R0705 1.45 1.62 0.72 1 1/4" X I" 1090R0706 1.58 1.67 0.75 1 1/2" X 1" 1D90R0806 1.65 1.80 0.92 1 1/2"X 11/4" 1D90R0807 1.82 1.88 1.08 2" X 1/2' 1D90R0904 1.49 1.88 1.08 2" X 3/4" 1D90R0905 1.60 1.97 1.24 2" X 1" 1D90R0906 1.73 2.02 1.40 2" Xl 1/4" 1090R0907 1.90 2.10 1.52 2" X 1 1/2" 1090R0908 2.02 2.16 1.65 Description I D. 1. Reducing Coupling F IIITEM1ØDE1LD1MJI ITEM I I NOM SIZE_j BLACK1I A 1NE1GH1i ®u LMM I X 1/2" 1DCR0604 1.69 0.39 I X 3/4" IDCR0605 1.69 0.53 Description I 0.1. 45 Degreed Elbow LM I1TEM CODEILIDIMENSItJNJ ITEM NOM SIZE I BLACK iLJI B I - 1D45B0606 1.12 1.12 0.46 1 1/4" 1045B0707 1.29 1.29 0.73 1 1/2" 11)45130808 1.43 1.43 0.92 11)45130909 1.68 1.68 1.50 www.sigmaco.com Ductile Iron Threaded Description I 0.1. Bushing - B F umo OUTSIDE HEAD INSIDE HEAD OTEM OflE11MENSi)Ni] PER 1NOM SIZE1 imm STYL9 wt I 1 X112" IDBUSO6O4 0.75 0.25 1.42 OUT 0.22 I X 3/4" IDBUS0605 0.75 0.25 1.42 OUT 0.17 1 1/4" X 1" I6BUS0706 0.80 0.28 1.76 OUT 1.28 1 1/2"X I" 1DBUSO8O6 0.83 0.31 2.00 OUT 0.44 1 1/2 X11/4"' IDBUS0807 083 031 200 OUT 0.30 2" X 1" IDBUS0906 0.88 0.41 1.95 IN 0.66 2" X 1/4" IDBUS0907 0.88 0.34 • 2.48 OUT 0.72 2" X 1 1/2" 1DBUS0908 0.88 0.34 2.48 OUT 0.61 Description I 1 D. Cross B B II usm _ II IITM COUE1EDIMENSTQNII ITEM 1 M SIZL11 BlACK II A 11 8 IWE1GF111 10X0606 1.50 1.50 0.98 1 1/4" 1DX0707 1.75 1.75 1.50 1 1/2" 10X0808 1.94 1.94 1.90 10X0909 2.25 2.25 2.95 1 1/4"X I" 1DX0706 1.58 1.67 1.27 11/2" X 1" iDX0806 1.65 1.80 1.45 2"X 1" 1DX0906 1.73 2.02 2.10 Description I DI. Cap I A WL .c®us umn IMP1F131M1I ITEM NOM SIZE [BLACK II IWEIGH IDK06 1.16 0.32 11/4' IDK07 1.28 0.43 11/2- IDK08 1.33 0.60 1DK09 1.45 0.91 www.sigmaco.com Description I D. I. Reducing Tee I I I T 1111111111117-7 USTED L -1 1 m I <~> 1llIEMIC0ElL EN D1MS1flN1I IThM NOM SIZE II BLACK1I A 1FW1[ IkNEIGH 1" x lx 1/2" 1DT060604 1.26 1.26 1.36 0.64 1" x 1" x 3/4" 101060605 1.37 1.37 1.45 0.73 I x 1/2 x I 1DT060406 1.50 1.36 1.50 071 1" x 3/4" x1" 1DT060506 1.50 1.45 1.50 0.76 1" x 1" x 1 1/4" 1 1Dt060607 1.67 1.67 1.58 0.98 1"x1"x1 1/2" 10T060608 1.80 1.80 1.65 1.16 1 1/4" x 1" x 1/2" 10T070604 1.34 1.26 1.53 0.82 1 1/4" x 1" x 3/4" 1DT070605 1.45 1.37 1.62 0.90 1 1/4 x I x I 1DT070606 1.58 1.50 1.67 1.00 1 1/4" x 1" x 1 1/4" 1DT070607 1.75 1.67 1.75 1.08 1 1/4" x1"xl 1/2" 1D1070608 1.88 1.88 1.82 1.42 1 1/4" x 1 1/4" x 1/2" 1DT070704 1.34 1.34 1.53 0.86 11/4" x 11/4" x 3/4" 10T070705 1.45 1.45 1.62 0.92 1 1/4" x 1 1/4" x 1" 10T070706 1.58 1.58 1.67 0.95 1 1/4" x 1 1/4" x 1" 101070708 1.88 1.88 1.82 1.45 11/4"x1 1/4"x2" 10T070709 2.10 2.10 1.90 1.75 11/2"x1"x1/2" 101080604 1.41 1.34 ' 1.66 0.95 11/2 x I x 3/4 10T080605 1.52 1.37 1.75 114 1 1/2"xl"x1" 1DT080606 1.65 1.50 1.80 1.17 1 I 1/2"xl"xl 1/4" 1DT080607 1.82 1.67 1.88 1.34 1 1/2" x 1" x 1 1/2" 1DT080608 1.94 1.80 1.94 1.45 1 1/2"x1 114"x112" 10T080704 1.41 1.34 1.66 1.05 11/2" x 11/4" x 3/4" 101080705 1.52 1.45 11.75 1.15 11/2" x 1 1/4" x 1" 10T080706 1.65 1.58 1.80 1.25 11/2" x 1/4" x 2" 1101080709 2.16 1 2.102.02, 1.90 I 1/2"x1 1/2"x1/2" 101080804 1.41 1.41 1.16 1.15 1 1/2 x 1 1/2 x 3/4 101080805 1.52 1.52 1.75 1.24 11/2" x 1/2" x 101080806 1.65 1.65 1.80 1.30 1 1/2" x 1 1/2" x 1" 10T080807 1.82 1.82 1.88 1.48 11/2 x 1/2 x2 1DT080809 216 216 202 198 2"x 1"x 2" 10T090609 2.25 2.02 11 2.25 2.15 2" x 1 1/4" x 2" 10T090709 2.25 2.10 2.25 2.30 2" x 11/2" x 1/2" 101090804 1.49 11.41 1.88 1.50 2" x 1 1/2" x 3/4" 101090805 1.60 1.52 1.97 1.62 2"x 1 1/2"x 1" 1 101090806 1.73 1.65 2.02 1.64 2" x 1 1/2" x 11/4" 101090807 1.90 1.82 2.10 1.80 2" x 1 1/2" x 1 1/2" 101090808 2.02 1.94 1 2.16 2.00 2" x 1/2" x2" 1D1090809 2.25 2.16 2.25 2.35 2" x 2" x 1/2" 10T090904 1.49 1.49 1.88 1.60 2" x 2" x 3/4" 1 DT090905 1.60 1.60 1.97 1.68 2"x2"xl" 1D1090906 1.73 1 1.73 2.02 1.85 2" x 2" x 1/4" 101090907 1.90 ' 1.90 2.10 2.04 2" x 2" x 1/2" 101090908 2.02 2.02 2.16 2.18 2" x 2" x 2 1/2" 1D1090910 2.60 2.60 2.39 3.61 2 1/2" x 2" x 3/4" 101100905 1.74 1.60 2.32 P2.28 11WER WE 1 kIri C.I. Threaded fittings are UL, cUL listed and Factory Mutual approved for 300psi servce. Gray iron per ASTM 126 class B. Dimensions conform to ANSI B 16.4 Class 125 except plugs conform to ASME B 16,14. Threads are NPT per ANSI/ASME 13I.20.1. Description [ - I C. 90 Degreed Elbow B I j llT 1W1MENSIQN1I ITEM 1 [M SI [BLACK H A 1EB1INEIGH11 1" 1C90B0606 1.50 1.50 0.85 1 1/4' 1C90B0707 1.75 1.75 1.22 1 1/2" 1C90B0808 1.94 1.94 1.55 2" 1C90B0909 2.25 2.25 2.45 2 1/2" IC90B1O1O 2.70 2.70 4.80 Description F C. 1. Straight Tee A A HUJB Lam [ NOM SIZE DTEM PPI LOJMENSINI [iTEM i BLACK U A II B IWEIGH 1" 1CT060606 1.50 1.50 0.85 1 1/4" 1C1070707 1.75 1.75 1.22 1 1/2" 1CT080808 1.94 1.94 1.55 2" 1CT090909 2.25 2.25 2.45 2 1/2" 1C T101010 2.70 2.70 6.39 Description I C. 1. Reducing Coupling W.@Hvs I USM NOM SIZE IITEMCOUEII fliMif IThM I LAcK I LA I WEIGH I X 1/2' ICCRO604 1.69 0.62 1 X 3/4" 1CCR0605 1.69 0.69 Description F Reducing 90 Degreed Elbow B 7r1 _ JJJA L1! PTMUEMENIflN1 ITEM I NOM SIZE I BLACK lEA UW1WEIGHT1 1 X1/2" 1C90R0604 1.26 1.36 0.44 1 X 3/4" 1C90R0605 1.37 1.45 0.52 1 1/4 X 1/2" 1C90R0704 1.34 1.53 0.64 1 1/4X3/4" 1C90R0705 1.45 1.62 0.72 1 1/4" X 1" 1C90R0706 1.58 1.67 0.75 1 1/2"X 1/2" 1C90R0804 1.60 1.70 1.17 1 1/2" X 3/4" 1C90R0805 1.61 1.72 1.30 1 1/2" X 1" 1C90R0806 1.65 1.80 0.92 1 1/2" X 11/4" 1C90R0807 1.82 1.88 11 1.08 2" X 1/2" 1C90R0904 1.49 1.88 1.08 2" X 3/4" 1C90R0905 1.60 1.97 1.24 2"X 1" 1C90R0906 1.73 2.02 1.40 2"X1 1/4" 1C90R0907 1.90 2.10 1.52 2" X 1 1/2" 1C90R0908 2.02 2.16 1.65 Description 1 C. 1. 45 Degreed Elbow SIZE O-M LBLACK IFIEMC1 WIMENSIOTNTI UK 1EW1WEFGI-111 [ITEM I 1C45B0606 1.12 1.12 0.46 1 1/4" 1C45B0707 1.29 1.29 0.73 1 1/2" 1C45B0808 1.43 1.43 0.92 1C45B0909 1.68 1.68 1.50 www.sigmaco.com NOM SIZE IUT mm 1UEffi1LDIMJETTEM I SLACK 1L1NELGR11 1/2" ICPLG0404 0.94 0.10 3/4" ICPLG0505 1.07 0.17 1CPLG0606 1.25 0.28 1 1/4" 1CPLG0707 1.36 0.44 1 1/2" ICPLG0808 1.45 0.62 ICPLG0909 1.56 0.91 Description I C. Cross A A 1IITEM GODE1[DLMENSTWIflTEM OM S1 BLACK il A lEB1WEIGH I" 1CX0606 1.50 1.50 1.54 11/4" 1CX0707 1.75 1.75 2.40 1 1/2" 1CX0808 I 1.94 3.19 2" 1CX0909 2.25 2.25 4.00 1 1/4"X 1" 1CX0706 1.58 1.67 2.05 1 1/2" X I" 1CX0806 1.65 1.80 2.40 2" X 1" 1CX0906 1.73r 2.02 1.36 1.45 1.50 1.50 1.58 1.65 1.53 1.62 1.57 1.75 1.82 1.53 1.62 1.67 1.82 1.90 1.66 1.75 1.80 1.88 1.94 1.66 1.75 1.80 1.88 1.94 2.02 1.66 1.75 1.80 1.88 2.02 2.25 2.25 1.88 1.97 2.02 2.10 1.88 2.25 1.88 1.97 2.02 2.10 2.16 2.39 0.95 1.10 1.08 1.18 1.52 1.73 1.17 1.38 1.47 1.80 2.05 1.37 1.54 1.65 2.21 2.55 1.41 1.65 1.65 2.00 2.30 1.58 1.72 1.85 2.22 2.45 2.80 1.76 1.87 1.94 2.29 3.28 3.40 2.80 2.09 2.40 2.54 2.85 2.24 3.75 2.60 2.71 2.97 3.32 3.72 5.10 Cast Iron mrdec1 Fit Description F I C. 1. Reducing Tee - Description I CA. Plugs cus UMD A , Usm -- Eoa--1 IFiBLACK1[A II B 1" x l"x 1/2' 1CT060604 1.26 1.26 1" x lx 3/4' 1CT060605 1.37 1.37 lx 1/2" x1" 1C1060406 1.50 1.36 x 3/4" xl" 1CT060506 1.50 1.45 lxix 11/4" 1CT060607 1.67 1.67 l"xl"xl 1/2" 1CT060608 1.80 1.80 11/4" x1" x 1/2" 1CT070604 1.34 1.26 1 1/4" x 1" x 3/4" 1C1070605 1.45 1.37 11/4" xl" x 1" 1CT070606 1.58 1.50 I 114"x1"x1 1/4" 1CT070607 1.75 1.67 11/4' xl" x 1/2" 1CT070608 1.88 1.80 11/4" x 1/4" x 1/2" 1CT070704 1.34 1.34 1 1/4" x 1 1/4" x 3/4" 1CT070705 1.45 1.45 11/4" x 1/4" xl" 1CT070706 1.58 1.58 11/4" x 1/4" x 1/2" 1CT070708 1.88 1.88 I 1/4"x1 114"x2" 1CT070709 2.10 2.10 11/2" x x 1/2" 1CT080604 1.41 1.34 I 1/2"xl"x314" 1CT080605 1.52 1.37 11/2" xl" xl" 1CT080606 1.65 1.50 11/2" x 1" x 11/4" 1 CT080607 1.82 1.67 1 1/2" xl" x 1/2" 1CT080608 1.94 1.80 11/2"x1 1/4"x1/2" 1CT080704 1.41 1.34 1 1/2" x 11/4" x 3/4" 1CT080705 1.52 1.45 11/2" x 1/4" x " lCT080706 1.65 1.58 1 l/2"xl 1/4"xl 1/4" 1CT080707 1.82 1.75 11/2" x 1/4" x 1/2" 1CT080708 1.94 1.88 1 1/2"x11/4"x2" 1CT080709 2.16 2.10 11/2" x 1/2" x 1/2" ICT080804 1.41 1.41 11/2" x 1/2" x 3/4" 1CT080805 1.52 1.52 1 1/2" x 11/2" x 1" 1CT080806 1.65 1.65 I 1/2"x1 1/2"x1 1/4" 1C1080807 1.82 1.82 1 1/2" x 1 1/2" x 2" 1CT080809 2.16 2.16 x I" x 2" 1CT090609 2.25 2.02 2" x 1 1/4" x 2" 1CT090709 2.25 2.10 2" x 1 1/2" x 1/2" lCT090804 1.49 1.41 2" x 1 1/2" x 3/4" 1CT090805 1.60 1.52 2" x 1 1/2" x 1" 1 C1090806 1.73 1.65 2" x 1 1/2" x 1 1/4" 1C1090807 1.90 1.82 2"x1 1/2"x1 1/2" 1C1090808 1.49 1.41 2" x 1 1/2" x 2" 1CT090809 2.25 2.16 2" x 2" x 1/2" 1CT096904 1.49 1.49 2" x 2" x 3/4" 1 C1090905 1.60 1.60 2' x2"x1" 1CT090906 1.73 1.73 2" x 2" x 1 1/4" 1CT090907 1.90 1.90 2" x 2" x 1 1/2" 1CT090908 2.02 2.02 2" x 2" x 2 1/2" 1CT090910 2.60 2.60 www.sigmaco.com I - DmFwfl POW* Hororda,%,, D Carbon Steel schedule 40 welded pipe nipples threaded to spec. ANSI/ASME 13I.20.1 Description I Black Steel LENGTH I I 1/8" liii 1/4" II NUMINL IL CLOSE 1NB0101 1NB0201 1NB0301 INB0401 1NBO501 INB0601 1NBO701 1NB080I 1NB0901 11/2" 1NBOI08 1NB0208 1NB0308 1NB0408 1NB0508 NA NA NA NA 2" 1NBO109 1NB0209 1NB0309 1NB0409 1NB0509 1NB0609 1N60709 1NB0809 NA 2 1/2" 1NBO110 1NBO2010 1NBO310 1NBO410 1NBO510 1NB0610 1NB0710 1NBO810 1NB0910 3" 1NB0III INB021I INB03I1 INB0411 INBO5II 1NB0611 1NB0711 1N80811 INBO9I1 31/2" 1NB0111-5 1NB0211-5 1NB0311-5 1NBO411-5 1NB0511-5 1NBO6II-5 INB0711-5 1NBO811-5 1NBO9I1-5 4" 1NBO112 1NB0212 1NB0312 1NB0412 1NB0512 1NB0612 1NB0712 1NB0812 1NB0912 4 112" 1N80112-5 1NB0212-5 1NB0312-5 1NB0412-5 1NB0512-5 1NB0612-5 1NB0712-5 1NB0812-51NB0912-5 5" 1NBO113 1NB0213 1NB0313 1NB0413 1NB0513 1NB0613 1NB0713 1NB0813 1NB0913 5 1/2" 1NBO113-5 1NB0213-5 1NB0313-5 1NB0413-5 1NB0513-5 1NB0613-5 1NB0713-5 1NB0813-5 1NB0913-5 6" INB0114 1NB0214 1NB0314 1NB0414 1NB0514 1NB0614 1NB0714 1NB0814 1NB0914 6 1/2" 1NBO114-5 1NB0214 -5 1NB0314-5 1NB0414-51NB0514-5 1NB0614-5 1NB0714-5 1NB0814-5 1NB0914-5 7" NA NA NA NA NA 1NB06147 1NB07147 1NB08147 1NB09147 7 1/2" NA NA NA NA NA 1NB06147-5 1 N B07147-5 1 N B08147-5 1NB09147-5 8" 1NBO115 1NB0215 1NB0315 1NB0415 1NB0515 1NB0615 1NB0715 1NB0815 1NB0915 8 1/2" NA NA NA NA NA 1NB0615 -5 1NB0715-5 1NB0815-5 1N0915- 9. 1NBO1I6 1NB0216 1NB0316 1NB0416 1NB0516 1NB0616 1NB0716 1NB0816 1NB0916 91/2" NA NA NA NA NA 1NB0616-5 1NB0716-51NB0816-5 1NB0916-5 1N80117 1NB0217 1NB0317 1NB0417 1NB0517 1NB0617 1NB0717 1NB0817 1NB0917 10 1/2" NA NA NA NA NA 1NB0617-5 1NB0717-51NB0817-5 1NB0917-5 - INBO118 1NB0218 1NB0318 1NB0418 1NB0518 1NB0618 1NB0718 1NB0818 1NB0918 111/2" NA NA NA NA NA 1NB0618-5 1NB0718-5 1NB0818-5 1NB0918-5 1NBO119 1NB0219 1NB0319 1NB0419 1NB0519 1NB0619 1NB0719 1NB0819 1NB0919 LENGTH NOMINAL SIZE 1 2 1/2" II " 11 4" IlIE " 1 CLOSE 1NB1001 1NB1101 1NB1201 1NB1401 INBiOlI INBilli NA NA 31/2" INBI01I-5 1NB1111-5 1NB12I1-5 NA 1NB1012 1NBI112 1NB1212 NA 41/2" INBI012-5 INBI112-5 1NB1212-5 NA 1NB1013 1NBI113 1NB1213 NA 51/2" 1NBI0I3-5 1NB1113-5 1NB1213-5 NA INB1014 1NB1114 1NB1214 1NB1414 INB1015 1NB1115 1NB1215 1N81415 1NB1016 1NB1116 1NB1216 1NB1416 1NB1017 1NB1117 1NB1217 1NB1417 1NB1018 1NB1118 1NB1218 1NB1418 INB1019 1NB1119 1NB1219 1NB1419 www.sigmaco.com I Mppn Pope MOPPWno eg~wgflhm fj Carbon Steel schedule 40 welded pipe nipples threaded to spec. ANSI/ASME 131.20.1 Galvanized to spec. ASTM A 153- for zinc coating. Description L Galvanized Steel LENGTH I 1 118" 11 1/4" if 3/8" 11 IIJMI4ML 1/2" 11 ILC 3/4" II 1" ii 11/4" II 1112" II 11/2" 1 CLOSE 1NG0I0I ING020I 1NG0301 1NG04P1 1NGO5OI 1NG0601 1NG0701 1NG0801 ING0901 1" NA 1NG020I-1 NA NA NA NA NA NA NA 1 1/4" NA NA NA NA NA NA NA NA - NA 11/2" 1NG0108 1NG0208 1NG0308 1NG0408 1NG0508 NA NA NA NA 2" 1NG0109 1NG0209 1NG0309 1NG0409 1NG0509 1NG0609 1NG0709 1NG0809 NA 2 1/2" 1NG0110 1NGO2O1O ING03I0 1NG0410 1NG0510 1NG0610 1NG0710 1NG0810 ING0910 3" 1NG0111 1NG0211 1NG0311 1NG0411 1NG0511 1NG0611 1NG0711 1NG0811 1NG0911 31/2" 1NG0111-5 1NG0211-5 1NGO3I1-5 1NG0411-5 1NG05II-5 1NG0611-5 1NG0711-5 1NG0811-5 1NG0911-5 4" 1NG0112 1NG0212 1NG0312 1NG0412 1NG0512 1NG0612 1 NG0712 1NG0812 tNG9912 41/2' ING0112-5 1NG0212-5 1NG0312-5 1NG0412-5 1NG0512-5 1NG0612-5 1NG0712-5 1NG0812-5 1NG0912-5 5" 1NG0113 1NG0213 1NG0313 1NG0413 1NG0513 1NG0613 1NG0713 1NG0813 , 1NG0913 5 1/2" 1NG0113-5 1NG0213-5 1NG0313-5 1NG0413-5 1NG0513-5 1NG0613-5 1NG0713-5 1NG0813-5 1NG0913-5 6" 1NG0114 1NG0214 1NG0314 1NG0414 1NG0514 1NG0614 1NG0714 1NG0814 : 1NG0914 6 1/2" 1NG0114-5 1NG0214-5 1NG0314-5 1NG0414-5 1NG0514-5 1NG0614-5 1NG0714-5 1NG0814-5 1NG0914-5 7" NA NA NA 1NG04147 NA 1NG06147 1NG07147 1NG08147 1NG09147 8" 1NG0115 1NG0215 1NG0315 1NG0415 1NG0515 1NG0615 1NG0715 1NG0815 1NG0915 81/2. NA NA NA 1NG0415-5 NA NA NA NA NA 9" 1NG0116 1NG0216 1NG0316 1NG0416 1NG0516 1NG0616 1NG0716 1NG0816 1NG0916 10" 1NG0117 1NG0217 1NG0317 1NG0417 1NG0517 1NG0617 1NG0717 1NG0817 1NG0917 11" 1NG0118 1NG0218 1NG0318 1NG0418 1NG0518 1NG0618 1NG0718 1NG0818 1NG0918 12" 1NG0119 1NG0219 1NG0319 1NG0419 1NG0519 1NG0619 1NG0719 1NG0819 1NG0919 [JENGTH I NOMINALSIZE 1 2 112" jI CLOSE 1NG1001 1NG1101 1NGI20I 1NG140I 3" 1NG1011 1NG1111 NA NA 3 1/2" 1NG1011-5 1NG1111-5 NA NA 4" 1NG10I2 1NG1112 1NG1212 NA 41/2" 1NG1012-5 1NG1112-5 1NG1212-5 NA 5" 1NG1013 1NG1113 1NG1213 NA 51/2" 1NG1013-5, 1NG1113-5 1NG1213-5 NA 6" 1NG1014 1NG1114 1NG1214 1NG1414 7" NA 1NGI114-5 NA NA 8" 1NG1015 1NG1115 1NG1215 1NG1415 9" ING1016 1NG1116 1NG1216 1NG1416 10" 1NG1017 1NG1117 1NG1217 1NG1417 11" 1NG1018 1NG1118 1NG1218 - 1NG1418 12" 1NG1019 1NG1119 1NG1219 1NG1419 www.sigmaco.com 11 L ©OLW O Manufactured from carbon steel (which conforms to ASTM A 865 standard) O Threads conform to ASME 13I.20.1 standards for pipe threads. El Sizes 2" and below are straight tapped and 2 1/2" and above are tapper tapped. Description 1 77771 Size Item Code 0 L ] 1/2" 1 MCC0404 1.063" 1.563" 3/4" 1MCC0505 1.313" 1.625" i" IMCC0606 1.576" 2.00" 1-1/4" IMCC0707 1.900" 2.063" 1 MCC0808 2.200" 2.063" 1MCCO909 2.750" 2.12511 2-1/2" IMCCIOIO 3250" 3.125" IMCCIIII 400" 3250" IMCCI2I2 5.00" 3.500" www.sigmaco.com victaulic.com I FireLock Fittings I Publication 10.03 Flow Data: Frictional Resistance Equivalent Feet/meters of Straight Pipe' Actual No. 002 Nominal Outside Size Diameter Elbows Straight Tee No. 001 No. 003 inches inches mm mm 90° Elbow 45° Elbow Branch Run 1¼ 1.660 - - - - 32 1 42.4 - - - - 1½ 1.900 - - - - 40 48.3 - - - - 2 2.375 3.5 1.8 8.5 3.5 50 60.3 1.1 0.5 2.6 1.1 21/2 2.875 4.3 2.2 10.8 4.3 65 73.0 1.3 0.7 3.3 1.3 3.000 4.5 2.3 11.0 4.5 76.1 mm 76.1 1.4 0.7 3.4 1.4 3 3.500 5.0 2.6 13.0 5.0 80 88.9 1.5 0.8 4.0 1.5 108 mm 4.250 6.4 3.2 15.3 6.4 108.0 2.0 0.9 1 4.7 2.0 4 4.500 6.8 3.4 16.0 6.8 100 114.3 2.1 1.0 4.9 2.1 5 5.563 8.5 4.2 21.0 8.5 125 1 141.3 2.6 1.3 6.4 2.6 139.7 mm 5.500 8.3 4.1 20.6 8.3 139.7 2.5 1.3 6.3 2.5 159 mm 6.250 9.4 4.9 25.0 9.6 158.8 2.9 1.5 1 7.6 2.9 6 6.625 10.0 5.0 25.0 10.0 150 168.3 3.0 1.5 7.6 3.0 16 MM 6.500 9.8 4.9 24.5 9.8 165.1 3.0 1.5 7.5 3.0 8 8.625 13.0 5.0 33.0 13.0 200 219.1 4.0 1.5 10.1 4.0 The flow data listed is based upon the pressure drop of Schedule 40 pipe. General Notes: NOTE: When assembling FireLock EZ couplings onto end caps, take additional care to make certain the end cap is fully seated against the gasket end stop. For FireLock EZ Style 009N/009H couplings, use FireLock No. 006 end caps containing the EZ marking on the inside face or No. 60 end caps containing the "QV EZ" marking on the inside face. Non-Victaulic end cap products shall not be used with Style 009/009V/009H couplings. Installation Note Reference should always be made to the 1-500 Victaulic Field Installation Handbook for This product shall be manufactured by Victaulic or to Victaulic specifications. All products the product you are installing. Handbooks are included with each shipment of Victaulic to be installed in accordance with current Victaulic installation/assembly instructions. products for complete installation and assembly data, and are available in POE formal Victaulic reserves the right to change product specifications, designs and standard on our website at www.victaulic.cuw. equipment without notice and without incurring obligations. Warranty Trademarks Refer to the warranty section of the current Price List or contact Victaulic for details. Victuulic° is a registered trademark of Victaulic Company. 10.03 1539 Rev M Updated 12/2014 © 2014 Victaulic Company. All rights reserved. victaulic.com 3 j Ac- tauIiC Fig. 200 - "Trimline" Fig. 200R (Import) - Adjustable Band Hanger "Trimline" Adjustable Band Hanger wlRetainer Ring C®US LISTED Size Range - 1/2' thru 8" pipe Material - Carbon Steel, Mil. Galvanized to G90 specifications Function - For fire sprinkler and other general piping purposes. Knurled swivel nut design permits hanger adjustment after installation. Features - (1/2" thru 2") Flared edges ease installation for all pipe types and protect CPVC plastic pipe from abrasion. Captured design keeps adjusting nut from separating with hanger. Hanger is eas- ily installed around pipe. (21/2" thru 8') Spring tension on nut holds it securely in hanger before installation. Adjusting nut is easily removed. Approvals - Underwriters' Laboratories listed (1/2" thru 8") in the USA (UL) and Canada (cUL) for steel and CPVC plastic pipe and Factory Mutual Engineering Approved (3/4" thru 8"). Conforms to Federal Specifications WW-H-171E, Type 10 and Manufacturers Standardization Society SP-69, Type 10. Maximum Temperature - 650°F Finish - Mil. Galvanized. Stainless Steel materials will be supplied with (2) hex nuts in place of a knurl nub. Order By - Figure number and pipe size Note - Figure 200R (import) with retainer ring and non-captured knurl nut. Dimensions • Weights Pipe Rod Size Max. Rec. Approx. Size Inch Metric A B Load Lbs. Wt./100 1/2 3/8 8mm or 10mm 31/8 2% 400 11 3/4 3/8 8mm or 10mm 31/8 21h 400 11 1 3/8 8mm or 10mm 33/8 25/8 400 12 11/4 3/8 8mm or 10mm 33/4 27/8 400 13 11/2 3/8 8mm or 10mm 3/8 27A 400 14 2 3/8 8mm or 10mm 41/2 3 400 15 21h 3/8 10mm 55/8 4'/e 600 27 3 3/8 10mm 57/8 4 600 29 3½ 3/8 10mm 7% 51/4 600 34 4 3/8 10mm 7% 5 1000 35 5 1/2 12mm 91/8 61/4 1250 66 6 1/2 12mm 101/8 6-Y4 1250 73 8 1/2 12mm 131/a 83/4 1250 136 OFFICE/MANUFACTURING FACIUTY • 1375 SAMPSON AVE. • CORONA, CA 92879 • PH: 951.737.5599 • FAX: 951.737.0330 CUSTOMER SERVICE • 800.786.5266 www.tolco.com FIG. 98 N. 98 - Rod Stiffener N.98B - Rod Stiffener w/Break-off Bolt Head Size Rang Secures 3/8 thru 7/8' hanger rod Material - Ca n Steel Function - Secure to hanger rod for vertical seismic bracing. Approvals - lncludeour Seismic Restraints Catalog approved Component of State of California OSHPD Approved Seismic Restraints System -•, Finish - Electro Galvanized Note - Available in HDG finish or Stainle'tterials. Order By - Figure number L.) Fli Fig. 99- All Thread Rod Cut to Length Size Range - Secures 3/8" thru 7/8' rod in 1" increments Material - Carbon Steel Maximum Temperature - 750°F Finish - Plain Note - Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By - Figure number, rod diameter, rod length and finish Dimensions od Max. Rec. Load Lbs. jk~For Service Temp 650*17 3/8 730 1/2 NS4, 1350 3/4 7/8 Fig. 100 - All Thread Rod Full Length Size Range - Secures 3/8' thru 11/2" rod in 10' lengths Material - Carbon Steel Maximum Temperature - 750°F Finish - Plain Note - Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By - Figure number, rod diameter and finish Dimensions • Weights Max Rec. Load Lbs. Rod For Service Temps Approx. Size 650°F Wt./100 1/4 240 12 3/8 730 29 1/2 1350 53 5/8 2160 84 3/4 3230 123 7/8 4480 169 1 5900 222 11/4 9500 360 11/2 13800 510 M OFFICE/MANUFACTURING FACILITY • 1375 SAMPSON AVE. • CORONA, CA 92879 • PH: 951.737.5599 • FAX: 951.737.0330 CUSTOMER SERVICE • 800.786.5266 www.tolco.com C®US LISTED Fig. 25 - Surge Restrainer Size Range - One size fits 3/4" thru 2" pipe. Material - Pre-Galvanized Steel Function - Designed to be used in conjunction with TOLCO® Band Hangers to restrict the upward movement of piping as it occurs during sprinkler head activation or earthquake type activity. The surge restrainer is easily and efficient- ly installed by snapping into a locking position on the band hanger. This product is intended to satisfy the requirements as indicated in the National Fire Protection Association NFPA 13, 2010 edition, 9.2.3.4.4.1 and 9.2.3.4.4.4 Can be used to restrain either steel pipe or CPVC plastic Pipe. Approvals - Underwriters' Laboratories Listed pnly when used with TOLCO band hangers Fig. 2, 2NFPA and 200, in the USA (UL) and Canada (cUL). Finish - Pre-Galvanized Order By - Figure number and TOLCO band hanger, size from 3/4" thru 2". Patent #5,344,108 OFFICE/MANUFACTURING FACILITY • 1375 SAMPSON AVE. • CORONA, CA 92879 • PH: 951.737.5599 • FAX: 951.737.0330 CUSTOMER SERVICE • 800.786.5266 wwwtolco.com FIG. 70S ILJ Fig. 70 - Steel Rod Coupling Fig. 70R - Steel Reducing Rod Coupling Fig. 70S - Short Pattern Steel Rod Coupling Fig. 71 - Steel Window Rod Coupling Size Range— 1/4' thru 11/2" rod Material - Carbon Steel Function - Used for coupling two threaded rods together of equal or reduced rod sizes, with or without inspection hole. Finish - Electro-Galvanized Note - Available in HDG finish or Stainless Steel materials. Fig. 70 Dimensions • Weights Rod Max Rec. Approx. Size Length Load Lbs. WtJ100 1/4 7/8 240 2 5/16 1/4 300 13 3/8 13/4 610 11 1/2 1/4 1130 11 5/8 21/8 1810 16 3/4 21/4 2710 27 7/8 21h 3770 57 1 23/4 4960 70 11/8 - 11/2' - Consult factory for specifications Fig. 7013 Dimensions • Weights Rod Max Rec. Approx. Size Length Load Lbs. WtJ100 3/8x1/4 7/8 240 4 1/2x3/8 13/4 610 7 5/8 x 1/2 21/8 1130 14 3/4x5/8 21/4 1810 21 7/8x3/4 21/2 2710 40 Fig. 70S/Fig. 71 Dimensions • Weights Rod Max Rec. Approx. Size Length Load Lbs. WtJ100 3/8 11/8 610 4 1/2 11/4 1130 6 For rod sizes 5/8" to 1" - consult factory OFFICE/MANUFACTURING FACILITY • 1375 SAMPSON AVE. • CORONA, CA 92879 • PH: 951.737.5599 • FAX: 951.737.0330 a. CUSTOMER SERVICE • 800.786.5266 www.tolco.com c®us LISTED UL Listed Design Load 2015 lbs. (8.96kN) Shown with Fig. 980 1" (25.4mm) Mm. ** See load ratings in UL Listed Design Load chart. Pipe Size 21/2" (65) 11/2" (32nim) 2002_21/2 X 1/2 Part Number Brace Pipe 224.9 (102.0) & Approx. Wt./100 211 (5omm) 2002_2112 X 2 Brace Pipe 283.3 (128.6) Design Load UL (80) 2002-3 X 11/2 241.0 (109.3) I 2002-3 X 2 299.4 (135.8) UL (100) 2002-4 X 11/2 268.4 (121.7) I 2002-4 X 2 326.8 (148.2) UL 6" (150) 2002-6 X 11/2 326.6 (148.1) I 2002-6 X 2 385.0 (174.6) UL 8" (200) 2002-8 X 11/2 1 381.3 (172.9) 1 2002-8 X 2 1 439.7 1 (199.4) UL 41 All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. Pipe Hangers & Supports 190 B-Line by 4J Seismic Bracing Fig. 2002 - Sway Brace Attachment @TOLGO Component of State of California OSHPD Approved Seismic Restraints System Size Range: Pipe size to be braced: 21/2 (65mm) thru 8" (200mm) all steel schedules, copper, plastic, FRP, cast iron and ductile iron. Consult factory when bracing other than steel. The Fig. 2002 accepts brace pipes sizes 114 (40mm) and 2" (50mm) steel schedule 100 through schedule 40. Material: Steel Function: For bracing pipe against sway and seismic disturbance. The pipe attachment component of a sway brace system: Fig. 2002 is used in conjunction with a TOLCO 900 Series sway brace attachments and joined together with bracing pipe. Install per NFPA 13 and/or TOLCO State of California OSHPD Approved Seismic Restrain Manual. Features: Unique design will not damage thin wall, plastic, copper or ductile iron pipe. Easy verification of proper installation by tightening bolts until ears touch. Installation: Place Fig. 2002 over pipe to be braced. Slide bracing pipe through attachment and tighten hex nuts until ears touch. Approvals: Underwriters Laboratories Listed in the USA (UL) and Canada (cUL). Included in our Seismic Restraints Catalog approved by the State of California Office of Statewide Health Planning and Development (OSHPD). For additional load, spacing and placement information relating to OSHPD projects, please refer to the TOLCO Seismic Restraint Systems Guidelines. Finish: Plain. Contact B-Line for alternative finishes and materials. Order By: Figure number, pipe size to be braced, pipe size used for bracing (1112 (40mm) or 2 (50mm)) and finish. Important Note: Fig. 2002 is precision manufactured to perform its function as a critical component of a complete bracing assembly. To ensure performance, the UL Listing requires that the Fig. 2002 must be used only with other TOLCO bracing products. ®TOLCO C®US <e> LISTED Set Scre Inc All dimensions In charts and on drawings are in inches. Dimensions shown In parentheses are in millimeters unless otherwise specified. Pipe Hangers & Supports 170 BLine by f%4tj TOLCOTM Seismic Bracing Fig 4L - Longitudinal "In-Line" Sway Brace Attachment Size Range: 2" (50mm) through 8" (200mm) IPS. Material: Steel Function: For bracing pipe against sway and seismic disturbance. Approvals: Underwriters Laboratories Listed in the USA (UL) and Canada (cUL) 21/2" (65mm) through 8" (200mm) pipe. Approved by Factory Mutual Engineering (FM), 2" (50mm) through 8" (200mm) pipe. Installation Instructions: Fig. 4L is the braced pipe attachment component of a longitudinal sway brace assembly. It is intended to be combined with the bracing pipe and TOLCO structural attachment component to form a complete bracing assembly. NFPA 13 and/or OSHPD guidelines should be followed. To Install: Place the Fig. 4L over the pipe to be braced and tighten bolts. Then engage "bracing pipe" into jaw opening and tighten set screw until head snaps off. Jaw attachment can pivot for adjustment to proper brace angle. Finish: Plain. Contact B-Line for alternative finishes and materials. Order By: Figure number, pipe size and finish. fail 4-Way Riser Brace (plan view) Part Pipe Size A I I 1 Bolt Size Max. Rec. 2015 Load (8.96) *Max. Design I Load ' Approx. 41_21/2 21/2 (65) 6/16 (163.5) 21/2 (63.5) 2I4 (69.8) 1/2"-13 2015 (8.96) 3000 (13.34) 253 (114.7) 41-3 (80) (177.8) 2/4" (69.8) 31/16 (77.8) 1/2"..13 2015 (8.96) 1550 (6.89) 268 (121.5) 41-4 (100) 81/2 (215.9) 3/8" (85.7) 311/16" (937) 1/2"_13 2015 (8.96) 1550 (6.89) 348 (157.8) 41-5 (125) 93/4" 1 (247.6) 3/8" 1 (98.4) 1 43/8" (111.1) 1/2"..13 2015 (8.96) 1450 (6.45) 380 (172.3 4L-6 (150) 111/2 (292.1) 5" (127.0) 51/8" (130.2) 1/2"_13 2015 (8.96) 1450 (6.45) 640 E(330.2)] 41-8 (200) 131/4" (336.5) 5I8" (142.8) 5/8" (142.9) 1/2"_13 2015 (8.96) 1450 (6.45) 728 Part Size :Pipe -ir Design Load 4L-21/2 21/2" (65) 2015 (8.96) 1030 (4.58) 1180 (5.24) 1420 (6.31) 1590 (7.07) 41-3 (80) 2015 (8.96) 1030 (4.58) 1180 (5.24) 1420 (6.31) 1590(7.07) 41.-4 (100) 2015 (8.96) 530 (2.36) 730 (3.25) 890 (3.96) 990 (4,40) 4L-5 (125) 1 2015 (8.96) 530 (2.36) 1 730 (3.25) 1 890 (3.96) 990(4. 41-6 (150) 1 2015 (8.96) 530 (2.36) 1 730 (3.25) 1 890 (3.96) 990 (4.40) 41-8 8" (200) 2015 (8.96) 490 (2.18) 1 680 (3.02) 1 830 (3.69) 930 (4.13) * The loads listed are axial loads on the brace. The horizontal load capacity, H, of the brace is: H = F x sin ?, where ? the installation angle measured from the vertical. FM approved when used with 1", 11/4', 11/2' 0r2" Sch. 40 brace pipe. Eaton's B-Line Business seismic bracing components are designed to be compatible only with other B-Line bracing components, resulting in a listed seismic bracing assembly. B-Line's warranty for seismic bracing components will be the warranty provided in B-Line's standard terms and conditions of sale made available by B-Line, except that, in addition to the other exclusions from B-Line's warranty, Eaton's B-line Business makes no warranty relating to B-Line's seismic bracing components that are combined with products not provided by Eaton's B-Line Business. Seismic Bracing TOLCO Fig. 980 - Universal Swivel Sway Brace Attachment - /8"-16 to /4"40 rods TOLCO' Fig. 980H - Universal Swivel Sway Brace Attachment - /8"-9 to 11/4"7 rods Size Range: One size fits bracing pipe 1' (25mm) thru T (50mm), 12 gauge (2.6mm) channel, and all structural steel up to 1/4' (31 .7mm) thick. Material: Steel. Stainless Steel Type 316 (SS6) optional. Function: Multi-functional attachment to structure or braced pipe fitting. Features: This product's design incorporates a concentric attachment opening which is critical to the performance of structural seismic connections. NFPA 13 (2010) 9.3.5.8.4 indicates clearly that fastener table load values are based only on concentric loading. Mounts to any surface angle. Break off bolt head assures verification of proper installation. Installation: Fig.980 is the structural or transitional attachment component of a longitudinal or lateral sway brace assembly. It is intended to be combined with the 'bracing pipe' and TOLCO 'braced pipe' attachment, Fig. 1000, 1001, 2002, 4L, 4A or 4B to form a complete bracing assembly. NFPA 13 and/or OSHPD guidelines should be followed. To Install: Place the Fig. 980 onto the 'bracing pipe'. Tighten the set screw until the head breaks off. Attachment can pivot for adjustment to proper brace angle. Approvals: -Underwriters Laboratories Listed in the USA (UL) and Canada (cUL). Approved by Factory Mutual Engineering (FM). Included in our Seismic Restraints Catalog approved by the State of California Office of Statewide Health Planning and Development (OSHPD). For additional load, spacing and placement information relating to OSHPD projects, please refer to the TOLCO Seismic Restraint Systems Guidelines. Note: Fig. 980 Swivel Attachment and Fig. 1001, Fig. 1000, Fig. 2002, Fig. 4A, Fig. 4B or Fig. 4L pipe clamps make up a sway brace system of UL Listed attachments and bracing materials which satisfies the requirements of Underwriters Laboratories and the National Fire Protection Association (NFPA) Finish: Plain, Electro-Galvanized or Stainless Steel. Contact customer service for alternative finishes. Order By: Figure number and finish. US Patent Numbers Pat. #6,273,372, Pat. #6,517,030, Pat. #6,953,174, Pat. #6,708,930, Pat. #7,191,987, Pat. #7,441,730, Pat. #7,669,806 Component of State of California OSHPD Approved Seismic Restraints System kA 980 _N_ II, us LISTEU Mounting Hardware Is Not Included U E Part Number A in. (mm) B in. (mm) D* in. (mm) Max. Horizontal Design Load (cUlus) lbs./(kN) Max. Horizontal Design Load** (FM) 30°-44° 45°-590 600.740 75°-900 lbsJ(kN) IbsI(kN) lbs./(kN) lbsf(kN) App rox. Wt./1100 lbs. (kg) 980- 51/4" (133.3) 1/8" (47.6) 13/32" (10.3) 149 (67.6) 980_1/2 51/4" (133.3) 1/8" (47.6) 17/32" (13.5) 148 (67.1) 980-/8 51/4" (133.3) 1/8" (47.6) 11/16" (17.5) 147 (66.7) 980-/4 51/4" (133.3) 1/8" (47.6) 13/16" (20.5) 2015 1320 1970 2310 2550 146 (66.2) 980H-7/a 6/4" (171.4) 31/2" (88.9) /16" (23.8) (8.96) (5.87) (8.16) (10.27) (11.34) 402 (182.3) 980H-1 6/4" (171.4) 31/2" (88.9) 11/16" (27.0) 400 (181.4) 980H-11/8 6/4" (171.4) 31/2" (88.9) 1/16" (30.2) 397 (180.1) 980H-l'14 6/4" (171.4) 31/2" (88.9) 1/16" (33.3) 390 (176.9) * Mounting attachment hole size. Important! For load information when using Fig. 980 with 1 ** Installed with 1" or 11/4" Schedule 40 brace pipe. pre-installed or post-installed concrete anchors in compliance with NFPA 13 (2016) or ASCE 7-10, including prying factors, see load tables on pages ALl thru AL21. Eaton's B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components, resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton, except that, in addition to the other exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are combined with products not provided by Eaton. All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. B-Line series Pipe Hangers & Supports 186 Eaton All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. Pipe Hangers & Supports 68 B-tine by E4U Pipe Hangers Fig. 120 - "U" Hanger Size Range: Size 3/4" (20mm) thru 8" (200mm) pipe ØTOL Material: Steel Function: Used to support piping from wood beams where no contraction is expected. Used extensively in automatic fire sprinkler systems. Approvals: Meets or exceeds the requirements of National Fire Protection Association (NFPA), Pamphlet 13. Included in our Seismic Restraints Catalog approved by the State of California Office of Statewide Health Planning and Development (OSHPD). For additional load, spacing and placement information relating to OSHPD projects, please refer to the Seismic Restraint Systems Guidelines. Le Maximum Temperature: 750°F (399°C) (Sp Finish: Plain. Contact B-Line for alternative finishes and materials. Order By Part number, pipe size, length and finish TWit 120-I4 3/4 I .Size (20) & /16 I (7.9) Fastener Size 16 x 2* Max. Rec. 250 • (1.11) 120-1 (25) /16" (7.9) 16 x 2° 250 (1.11) 120_11/4 11/4" (32) /16" (7.9) 16 x 2° 250 (1.11) 120-11h 11h" (40) /16" (7.9) 16x2° 250 (1.11) 120-2 (50) /16" (7.9) 16 x 2* 250 (1.11) 120_2112 21/2" (65) /8" (9.5) /8 x 21/2** 320 (1.42) 120-3 (80) 3/9" (9.5) x 2I2°° 320 (1.42) 120-3112 31" (90) 3/9" (9.5) /8 x 21/2** 560 (2.49) 120-4 (100) /8" (9.5) 1/2 X 3** 560 (2.49) 120-5 (125) 1/2" (12.7) 1/2 X 3** 560 (2.49) 120-6 611 (150) 1/2" (7) 1 x 3°° 760 (3.38) 120-8 8" !.. 1/2" (12.7) 1 5/8 X 3° -- (--) * Drive Screw ** Lag Bolt With minimum safety factor of 5 Fastener schedule per NFPA -' Not less than Wood flooring P 2" nominal width Product Features I No pre-drilling required. Not less than Quick to install using the Sammy 3 nominal thickness (2-1/2") Nut Driver with an 18V cordless I I (depth or side WolJoist of vertical member) Saves time from traditional Double sheevock methods. Ceiling .1 .a" • Reduces installation cost. Made in the U.S.A. 1/4" 8002957 GST 100 1/40 1" 210 (7/16' OSB) 25 125 670 (3/4 Ply) 1/4' 8003957 GST 200 1/4x2 1760 (Fir) 25 125 [ - 1/4" - 8004957 GST 300 1/4x3" 2060 (Fir) 25 125 1 3/8" 8006957 GST .75 - 1/4 x314" - 564 (3/4" Ply) 25 125 - 3/8" 8007957 GST 10 1/4x 1" 670 300 25 125 3/8" 8008957 GST 20 1/4o2" 1760 (Fir) 850 1475 25 125 3/8" -. 8068925 GST2O-SS - 1/402" 1760 (Fir) 850 25 125 318' 8009925 GST 25-380 3/80 2-1/2" 2113 (Fir) 1500 25 125 3/8' 8010957 GST 30 1/403" 2060 (Fir) 1500 1475 25 125 #14 black 3/8" 8069925 GST 30-SS 1/403" 2060 (Fir) 25 125 - DriverNut Part #8113910 3/8" 8011925 GST40 1/404" 2)80 (Fir) 25 125 3/8" 8012925 GST 60 1/4 s 6" 2230 (Fir) 25 125 - [ 1/2" 8013925 GST2 1/4x2" 1760 (Fi4 25 125 1/2" 8014925 GST 2.5-380 3/8x2-1/2" 2113 (Fir) 25 125 1/2 8015925 GST3 1/4x3" 2275 (Fir) - 125 1/2" 8016925 GST4 1/4o4" 2180 (Fir) 25 125 1/2" 8017925 GST6 1/4x6" - 2230 (Fir) 25 125 #14 SW Red Nut Driver Part # 8114910 Product Features Eliminates distortion of threaded rod. • Saves time from traditional methods. , • Accommodates up to 3 Y2" x 12 pitch roof. • Reduces installation cost Allows 17" deflection from vertical. • Made in the U.S.A. •• 44& 3/8 8139957 • SH-GST 20 1/4 x2" 1257 (Fir) 1050 1475 25 125 125 3/8" 8141957 Sl-l-GST 30 1/4 o 3" 1720 (Fir) 1500 1475 25 125 #14 Black Nut Driver SPECIAL NUT DRIVER SYSTEM: The nut drivers were designed with a unique spin-off feature which provides a fast and safe installation each time. When the face of the driver comes into Part #8113910 contact with the material you are installing into, continue drilling until nut driver spins free. Installation is then complete. Warranty requires the use of the appropriate nut driverfor installations. For the most up to date information, visit www.sammysuperscrew.com 4 \=P/ (... : Not less than 2 nominal width Product Features (1-1/2") up to 3-1/2" pipe; not less than No pre-drilling required. 3' (2-1/2") nominal width 4' & 5" pipe Floor Joist Quick to install using the Sammy Minimum 2-1/2" from bosom for Nut Driver with an 18V cordless branch lines. Minimum 3' from bosom for main lines. Exception: This drill/driver. requirement shall not apply 1o2" or thicker nailing snips resting on top of steel beams. Saves time from traditional methods. Reduces installation cost. T Made in the U.S.A. 1/4" 8018957 SWG 100 1/4 xl" 622 (Fir) 25 125 1/4" 8019957 SWG 200 //4x 2' 1725 (Fir) 25 125 - - 8020957 SWG 10 1/4s1" 622 (Fir) 300 25 125 , 3/8 8021957 SWG 20 1/4 x 2" 1725 (Fir) 1050 25 125 42 3/8 - 8073925 SWG 20-SS 1/402 1725 (Fir) 850 25 125 #14 SW Red 42.. 3/8" 8022925 SWG 25-380 3/8 X 2-1/2' 2249 (Fir) 1500 25 125 Nut Driver [ 3/8" 8023925 SWG 30 1/4x3" 1884 (Fir) 25 125 Part # 8114910 I Insert the appropriate nut driver into a 3/8' or 112"portable drill Insert the SAMMYS into the #14 (black) nut driver (p/n 8113910). Drill should be in a vertical position. Push the face of the nut driver tight to the member. When the nut driver spins freely on the SAMMYS, stop drill and remove. The SAMMYS is now ready to receive 1/4", 3/8", 1/2" or metric all thread rod, bolt stock. (The 1/2" requires the #14S W red nut driver) Note: When installing DSTR, follow the above instructions, then add retainer nut and torque to 20 foot lbs. for maximum pullout in purlin steel. Insert the appropriate not driver into a 3/8" or 112"portable drill. Insert the SAMMYS into the #I4SW (red) nut driver (p/n 8114910). With drill unit in a horizontal position and at a right angle to the structural member, begin installation. When the nut driver spins free on the SAMMYS, stop the drill and remove. The unit is now ready to receive I/4' 3/8" or metric all thread rod or bolt stock. Note: When installing SWDR, follow the above instructions, then add retainer nut and torque to 20 foot lbs. for maximum pullout in purlin steel. .,MOM. r II SPECIAL NUT DRIVER SYSTEM: The nut drivers were designed with a unique spin-off feature which provides a fast and safe installation each time. When the face of the driver comes into contact with the material you are installing into, continue drilling until nut driver spins tree. Installation is then complete. Warranty requires the use of the appropriate nut driverfor installations. ACCESSORIES +'c: 1Itsc Pie-drill a 5/8" hole with a regular drill or ho saw. Insert SST screw into #14 black river. With wing nut and washer on bolt, Insert win through surface, and begin installation. When boliJe-ricure and nut driver spins free, stop drill motor Hollow Core SST screw is now ready to receive 1/4", 3/8", or Metric all thread rod or bolt stock. 'IfL.1/4" :: #14 Black Nut Driver Part # 8113910 8063925 SST 300 8064925 SST 30 1/4 x 3 450 (Lath & Plaster) 25 125 404 (2 Layers 5/8 Rock) 1/4 x 3 450 (Lath & Plaster) 25 125 404 (2 Layers 5/8 Rock) 3/16" eyelet to accommodate common wire size. ICC approvals can be found at www.itwbuildex.com under Evaluation Report# ER-5367. Approvals Substrate Part Model Point Overal Total Description Ultimate Max ICC Test Box Case Number Length Pullout (lbs) Gauge Load (Ibs) Qty City ik rt icc STEEL 8107957 CwsD? Teks - lxi" 2" - 472(Oga)16ga170(209a)25 125j 1 11 ICC STEEL 8190957 CWSD 15* Gimlet 1/4 x 1-1/2" 2-3/4" 472 (20ga) 20 ga. 170 (20 ga.) 25 125 WOOD Tek, 1393 (Fir) IJ L STEEL 8108957 CWSD2 Teks V? 3-V4 ga) 16 ga 170 (20 ga) 3V25 CWIT ICC 8110910 CWll Installation Tool Installation Tool Does not comply with ROHSrequlremen!s Part# 8110910 (E)POTTER BELLS The Symbol of Protection PBA-AC & MBA-DC These vibrating type bells are designed for use as fire, burglar or general signaling devices. They have low power consumption and high decibel ratings. The unit mounts on a standard 4" (101mm) square electrical box for indoor use or on a model BBK- I weatherproof backbox or BBX- 1 deep weatherproof backbox for outdoor applications. Weatherproof backbox model BBK-1, Stock No. 1500001. UL, ULC, and FM Approved Sizes Available: 6" (150mm), 8" (200mm) and 10" (250mm) Voltages Available: 24VAC I2OVAC 12VDC (10.2 to 15.6) Polarized 24VDC (20.4 to 31.2) Polarized Service Use: Fire Alarm General Signaling Burglar Alarm Environment: Indoor or outdoor use (See Note 1) -40° to 150°F (40° to 66°C) (Outdoor use requires weatherproof backbox.) Termination: AC Bells - 4 No. 18 AWG stranded wires DC Bells - Terminal strip Finish: Red powder coating Optional: Model BBK- 1 weatherproof backbox Model BBX-1 deep weatherproof backbox Notes: Minimum dB ratings are calculated from integrated sound pressure measurements made at Underwriters Laboratories as specified in UL Standard 464. UL temperature range is -30° to 150°F (-340 to 660C). Typical dB ratings are calculated from measurements made with a conventional sound level meter and are indicative of output levels in an actual installation. ULC only applies to MBA DC bells. Size inches (mm) Voltage Model Number Stock Number Current (Max.) Typical dB at 10 ft. (3m) (2) Minimum dB at 10 ft (3m) (1) 6(150) 12VDC MBA-6-12 1750070 .12A 85 76 8(200) 12VDC MBA-8-12 1750080 .12A 90 77 10 (250) 12VDC MBA-10-12 1750060 .12A 92 78 6(150) 24VDC MBA-6-24 1750100 .06A 87 77 8(200) 24VDC MBA-8-24 1750110 .06A 91 79 10 (250) 24VDC MBA-10-24 1750090 .06A 94 80 6(150) 24VAC PBA246 1806024* .1 7A 91 78 8 (200) 24VAC PBA248 1808024* .17A 94 77 10 (250) 24VAC PBA2410 1810024* .17A 94 78 6(150) 120VAC PBA1206 1806120* .05A 92 83 8(200) 120VAC PBA1208 1808120* .05A 99 84 10 (250) 120VAC PBA12010 1 1810120* .05A 99 86 All DC belts are polarized and have built-in transient protection. * Does not have ULC listing. I AWARNING I In outdoor or wet installations, bell must be mounted with weatherproof backbox, BBK-1 or BBX-l. Standard electrical boxes will not provide a weatherproof enclosure. If the bell and/or assembly is exposed to moisture, it may fail or create an electrical hazard. Potter Electric Signal Company, LLC • St. Louis, MO, • Phone: 866-572-3005/Canada 888-882-1833 • www.pottersignal.com PRINTED IN USA MFG. #5400776 - REV Y-1 PAGE 1 OF 2 01/13 Weatherproof Backbox Dimensions Inches (mm) Fig. 2 Box has one threaded 1/2" conduit entrance 53/4" (146) i — — I I 515" (41) DWG# 776-2 33/8" 5" L? 06t (127) 33/8" (86) 4 1/4" (LOS) (DPOTTER BELLS The Symbol of Protection PBA-AC & MBA-DC Bells Dimensions Inches (mm) Fig. 1 -, 10" —/ (25 1E 10) (150) 211/16" (68) DWG#776-I Wiring (rear view) Fig. 3 A.C. BELLS WHITE (OUT) WHITE (IN) 2CBLACK FROMCONTROL PANEL OR (OUT) PRECEDING HELL IILACI((IN)__________ CAUTION WHEN ELECTRICAL SUPERVISION IS REQUIRED USE IN AND OUT LEADS AS SHOWN. NOTES, I. WHEN USING AC BELLS. TERMINATE EACH EXTRA HIRE SEPARATELYAFTER LAST HELL. a END-OF-LINE RESISTOR IS NOT REQUIRED ON AC BELLS. DWG# 776-3 Installation The bell shall be installed in accordance with NFPA 13, 72, or local AHJ. The top of the device shall be no less than 90" AFF and not less than 6" below the ceiling. Remove the gong. Connect wiring (see Fig. 3). Mount bell mechanism to backbox (bell mechanism must be mounted with the striker pointing down). Reinstall the gong (be sure that the gong positioning pin, in the mechanism housing, is in the hole in the gong). Test all bells for proper operation and observe that they can be heard where required (bells must be heard in all areas as designated by the authority having jurisdiction). Ak WARNING Failure to install striker down will prevent bell from operating. PRINTED IN USA MFG. #5400776. REV Y-1 PAGE 2 OF 2 01/13 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION Ir OFFICE OF THE STATE FIRE MARSHAL _____ LISTING SERVICE FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING No. 7135-0328:0119 Page 1 of 1 CATEGORY: 7135--AUDIBLE DEVICES LISTEE: Potter Electric Signal Co1609 Park 370 Place, Hazelwood, 63042 United States Contact: Bill Witherspoon (314) 595-6900 Fax (314) 595-6999 Email: BillWpottersignal.com DESIGN: Models SB624-153075, 5B624-75110, PBA246, PBA248, PBA24I0, PBA12O6, PBA1208, PBA120I0, *pBD126 *PBD..128 *PBD..1210 *pBD..246 *pBD248 * PBD-2410 vibrating bells. Suitable for outdoor use when used with Model BBK-1 backbox. Models are AC or DC powered and available in 6', 8" and 10". Models MBA-6, -8 and -10 bells, suitable for outdoor use when used with Model BBX-1 backbox. Refer to listee's data sheet for detailed product description and operational considerations. RATING: PBA-246, -248, -2410: 24 VAC PBA-1206, -1208, -12010: 120 VAC MBA-6, -8, -10: 12or24VDC *pBD126 -128, -1210: 12VDC, .12A *PBD..246 -248, -2410: 24VDC, .06A INSTALLATION: In accordance with listee's printed installation instruction, applicable codes & ordinances, and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model number and UL label. APPROVAL: Listed as audible devices for use with separately listed compatible fire alarm control units. If this appliance is required to produce a distinctive three-pulse Temporal Pattern Fire Alarm Evacuation Signal (for total evacuation) in accordance with NFPA 72, 2002 Edition, the appliance must be used with a fire alarm control unit that can generate the temporal pattern signal. Refer to manufacturer's Installation Manual for details. Revision 01-31-2017 dcc . This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2017 Listing Expires June 30, 2018 Authorized By: DAVID CASTILLO, Program Coordinator Fire Engineering Division VSG (D POTTER LOW FLOW RATE VANE TYPE WATERFLOW The Symbol of Protection SWITCH WITH ELECTRONIC RETARD U.S. Pat. No. 3921989, Canadian Pat. No. 1009680 Other Patents Pending, Potter Electric, Rd., 1990 General Information The Model VSG is a flexible vane type of waterfiow switch for use in wet pipe water mist systems where a low flow for alarm is required. It is designed for installation in sections of 2 to 4 inch (50mm to 100mm) stainless steel or brass pipe with wall thickness in accordance with the above specifications (see "Nominal OD and Wall Thickness"). The unit may also be used as a sectional waterfiow detector on large systems. The unit contains an output relay and an adjustable electronic retard. The relay is actuated when aflow of 3 gallons per minute (11,4 LPM) or more occurs downstream of the device. The flow condition must exist for a period of time necessary to overcome the selected retard period. Enclosure The unit is enclosed in a general purpose, die-cast housing. The cover is held in place with two tamper resistant screws which require a special key for removal. A field installable cover tamper switch is available as an option which may be used to indicate unauthorized removal of the cover. See bulletin no. 5400775 for installation instructions of this switch. UL, IJLC, and CSFM Listed Service Pressure: Up to 450 PSI (31 BAR) Flow Required for Alarm: 3.0 GPM (11,4 LPM) Maximum Surge: 18 FPS (5,5 m/s) Power Requirements: STANDBY: lOma at 120V AC or 1.5ma at 24V AC/DC ALARM: 40ma at 120V AC or 35ma at 24V AC/DC Contact Ratings: DPDT (Form C) 2 Amps at 0-30VDC or 0-125VAC resistive Conduit Entrances: 2 knockouts provided for 1/2' conduit Environmental Specifications: Suitable for indoor or outdoor use with factory installed gasket and die-cast housing. NEMA 4 Rated Enclosure - use with appropriate conduit fitting. Temperature Range: 40°F/120°F, 4,5°C/49°C Non-corrosive sleeve factory installed in saddle. Caution: This device is not intended for applications in explosive environments. Nominal OD and Wall Thickness: (60,3mm OD), 3,9mm to 4,5mm wall 2 1/2" (73,0mm OD), 4,8mm to 5,2mm wall 2 1/2" (76,1mm OD), 4,3mm to 4,7mm wall (88,9mm OD), 5,0mm to 5,6mm wall (114,3mm OD), 5,4mm to 6,4mm wall Service use: Water mist systems where low flow for alarm is required. Optional: Cover Tamper Switch Kit, Stock No. 0090018 Installation See Fig. 1 These devices may be mounted on a horizontal or vertical pipe. On horizontal pipe they should be installed on the top side of the pipe where they will be accessible. The units should not be installed within 6" (15cm) of a fitting which changes the direction of the waterfiow or within 24" (60cm) of a valve or drain. Drain the system and drill a hole in the pipe using a circular saw in a slow speed drill. The 2" (50mm) and 2 1/2" (65mm) devices require a hole with a diameter of 1 1/4" +1/8" -1/16" (32mm ± 2mm). The 3" (80mm) and 4" (100mm) devices require a hole with a diameter of 2" ± 1/8" (50mm ± 2mm). Clean the inside of the pipe of all growth or other material for a distance equal to the pipe diameter on either side of the hole. Roll the vane so that it may be inserted into the hole; do not bend or crease it. Insert the vane so that the arrow on the saddle points in the direction of the waterfiow. Install the saddle strap and tighten nuts alternately to an eventual 20 ft-lbs. (27 n-m) of torque. See Fig. 1. The vane must not rub the inside of the pipe or bind in any way. Potter Electric Signal Company 2081 Craig Road, St. Louis, MO, 63146-4161 • Phone: 800-325-3936/Canada 888-882-1833• www.pottersignal.com PRINTED IN USA MFG. #5400999 - REV M PAGE 1 OF 2 5/08 liGHTEN RUTS ALTERNATELY TO AOl EOlTUAt. 20 FT—LBS. (27 n—n,) OF TORQUE MOUNT ON PIPE SO ARROW ON SADDLE P00115 IN DIRECTiON OF WATERFLOVI ROLL PADDLE VI OPPSTCU0N OF (262-30 TO INSTMJ_ DRILL HUE AS 862CA1ED PIPE SZE HOLE SE 2 to 2-1/2 I-1/4 + 1/8 - (SO to ROn,,,) (32n,n, ± 2m,n) 3 to 4 2 ± I/8 (80 to lOOn,,,) (50nn ± 2oon) VSG (E)POTTER LOW FLOW RATE VANE TYPE WATERFLOW The Symbol of Protection SWITCH WITH ELECTRONIC RETARD Retard Adjustment Fig. 1 The retard time is selected by turning the appropriate switches to the off position. Example: For 45 seconds turn switches 1, 2 and 3 to the off position. Approximate time is as follows: Switch Off Time in Sec. 1thru80n 0 1 15 l&2 30 1,2,&3 45 1,2,3,&4 60 1,2,3,4,&5 75 1,2,3,4,5,&6 90 7 not used 8 not used Fig. 2 Typical Electrical Connections MW rc. Q AUX. coo. Q CONTACTS HIGH VOLTAGE RELAY ACTION 24V BELL I N.O. 150 MCI I 61000 4/6 WIRE CONTROL PANEL CIRCUIT DETECTOR CIRCUIT END OF LINE RESISTOR OR COO. n.0.c00.n.0 FROM PANEL -.. RETURN TO CONTROL PANEL 24V DC POWER O I 67e 24V DC RELAY o. Q I AUX. tN D. l2 j. , SHOWN ENERGIZED CONTACTS CR0 0I NOTE: BASE MUST BE CONNECTED TO A GOOD EARTH GROUND. LOW VOLTAGE AC LOW VOLTAGE DC OWO. #985-1 Fig. 3 Switch Terminal Connections Clamping Plate Terminal I A CAUTION I When supervised circuits are used the following must be observed: An uninsulated section of a single conductor should not be looped around the terminal and serve as two separate connections. The DWO# 013.3 wire must be severed, thereby providing supervision of the connection in the event that the wire becomes dislodged from under the terminal. Application Warning! Due to the possibility of unintended discharges caused by pressure surges, trapped air, or short retard times, waterfiow switches that are monitoring wet pipe sprinkler systems should not be used as the sole initiating device to discharge AFFF, deluge, or chemical suppression systems. Testing: The operation of the waterfiow switch and the associated alarms is to be tested upon completion of the installation and periodically thereafter in accordance with the applicable NFPA standards and/or the authority having jurisdiction (manufacturer recommends quarterly or more frequently). A minimum flow of 3 GPM (11,4 LPM) is required to activate this device. PRINTED IN USA MFG. 45400999 - REV M PAGE 2 OF 2 5108 CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION OFFICE OF THE STATE FIRE MARSHAL FIRE ENGINEERING - BUILDING MATERIALS LISTING PROGRAM LISTING SERVICE LISTING No. 7770-0328:0010 Page 1 of I CATEGORY: 7770 -- VALVES/SWiTCHES LISTEE: Potter Electric Signal Co1609 Park 370 Place, Hazelwood, 63042 United States Contact: Bill Witherspoon (314) 595-6900 Fax (314) 595-6999 Email: BillWpottersignal.com DESIGN: Supervisory switches listed below to monitor pressure, OS&Y, gate, globe/gate, Ply, tank temperature or water level valves. Refer to listee's data sheet for detailed product description and operational considerations. HLS-B WLS-W PS-120A OSYSU-2 PTS-B OSYSU-1 P1 VS-B TTS-S WLS PTS-C RBVS *P515 WLS-S PS-40A OSYS-B PMS GVS PCVS-1 TTS-W PCVS-2 PS4O PS12O *P525 INSTALLATION: In accordance with listee's printed instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction. MARKING: Listee's name, model designation and FM or UL label. APPROVAL: Listed as sprinkler system supervisory switches. NOTE: Formerly 7738-0328:010 *Revision 09-07-2016 dc This listing is based upon technical data submitted by the applicant. CSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other Date Issued: July 01, 2017 Listing Expires June 30, 2018 Authorized By: DAVID CASTILLO, Program Coordinator Fire Engineering Division Fi reLock® Butterfly Valve t —MU Iid Style 705 with Weatherproof Actuator 10.81 F! 1.0 PRODUCT DESCRIPTION Available Sizes: 2 - 12/50 - 300 mm cULus Listed, LPCB Listed, FM and VdS Approved for service up to 300 psi/2068 kPa /20 bar. Designed for fire protection services only. Features a weatherproof actuator housing Approved for indoor and outdoor use. Actuation options: Hand wheel (2 - 12/50 - 300 mm) Exclusively for use with pipe and Victaulic products which feature ends formed with the Victaulic Original Groove System (OGS) groove profile (see section 7.0 for Reference Materials). 2.0 CERTIFICATION/LISTINGS c®us LISTED G410001 104j/04 NOTES Refer to Victaulic submittal publication 10.01 for details ALWAYS REFER TO ANY NOTIFICATIONS AT THE END OF THIS DOCUMENT REGARDING PRODUCT INSTALLATION, MAINTENANCE OR SUPPORT. System No. Location Spec Section Paragraph Submitted By Date Approved Date victaulic.com 10.81 5662 Rev 0 updated 08/2016 © 2016 Victaulic company. All rights reserved. 1 ictaulic' ui,4iilir mm 2.1 CERTIFICATION/LISTINGS Approval/Listing Service Pressures Series 705 Butterfly Valve cULus FM Vds __________ LPCB [ Size 50 up to 300psi/2068kPa n/a up to 300psi/2068kPa up to 300psi/2068kPa 2/2 65 up to 300psi/2068kPa up to 300psi/2068kPa n/a up to 300psi/2068kPa 76.1 mm up to 300psi/2068kPa up to 300psi/2068kPa up to 300psi/2068kPa up to 300psi/2068kPa 80 up to 300psi/2068kPa up to 300psi/2068kPa up to 300psi/2068kPa up to 300psi/2068kPa 1 up to 300psi/2068kPa up to 300psi/2068kPa up to 300psi/2068kPa up to 300psi/2068kPa 125 up to 300psi/2068kPa up to 300psi/2068kPa n/a up to 300psi/2068kPa 139.7mm up to 300psi/2068kPa up to 300psi/2068kPa up to 300psi/2068kPa up to 300psi/2068kPa 150 up to 300psi/2068kPa up to 300psi/2068kPa up to 300psi/2068kPa up to 300psi/2068kPa 165.1 mm up to 300psi/2068kPa up to 300psi/2068kPa n/a up to 300psi/2068kPa 200 up to 300psi/2068kPa up to 300psi/2068kPa up to 300psi/2068kPa up to 300psi/2068kPa 10 250 up to 300psi/2068kPa up to 300psi/2068kPa n/a up to 300psi/2068kPa 12 oo up to 300psi/2068kPa up to 300psi/2068kPa n/a up to 300psi/2068kPa 3.0 SPECIFICATIONS - MATERIAL Body: Ductile Iron conforming to ASTM A-536, Grade 65-45-12 End Face, 2 - 6"I50 - 150 mm: Ductile Iron conforming to ASTM A-536, Grade 65-45-12 Seal Retainer, 8 - 12"/200 - 300 mm: Ductile Iron conforming to ASTM A-536, Grade 65-45-12 Body Coating: Black alkyd enamel Disc: Ductile Iron conforming to ASTM A-536, Grade 65-45-12, with electroless nickel coating conforming to ASTM B-733 Seat: Grade "E" EPDM Stems: 416 stainless steel conforming to ASTM A-582 Stem Seal Cartridge: C36000 brass Bearings: Stainless steel with TEE lining Stem Seals: EPDM Stem Retaining Ring: Carbon steel Actuator: R 2 - 8/50 - 200 mm: Brass or bronze traveling nut on a steel lead screw, in a ductile iron housing D 10— 127250-300 mm: Steel worm and cast iron quadrant gear, in a cast iron housing 10.81 5662 Rev G Updated 08/2016 © 2016 victaulic company. All rights reserved. victaulic.com 2 jtiU —Ii c. victaulic.com 4.0 DIMENSIONS Style 705 Size Dimensions Actual Outside E to E DIA Nominal Diameter A B C D E F G H J inches inches inches inches inches inches inches inches inches inches inches MM mm mm mm mm mm mm mm mm mm mm 2 2.375 4.25 2.28 6.41 - 4.00 4.22 4.50 2.12 60.3 69.3 108.0 57.9 162.8 - 101.6 107.2 114.3 53.8 2 1/1 2.875 3.77 2.28 7.54 4.00 4.22 4.50 1.77 73 73.0 95.8 57.9 191.5 - - 101.6 107.2 114.3 45.0 3.000 3.77 2.28 7.54 4.00 4.22 4.50 1.77 761 mm 76.1 95.8 57.9 191.5 - 101.6 107.2 114.3 45.0 3 3.500 3.77 2.53 7.79 - - 4.50 4.22 4.50 1.77 88.9 88.9 95.8 64.3 197.9 114.3 107.2 114.3 45.0 4.250 4.63 2.88 8.81 5.50 4.22 4.50 2.20 108mm 108.0 117.6 73.2 223.8 - - 139.7 107.2 114.3 55.9 4 4.500 4.63 2.88 8.81 - 5.50 4.22 4.50 2.20 114.3 114.3 117.6 73.2 223.8 - 139.7 107.2 114.3 55.9 5.250 5.88 3.35 10.88 - 6.56 6.19 6.30 2.58 133mm 133.0 149.4 85.1 276.4 - 166.6 157.2 160.0 65.5 5.500 5.88 3.35 10.88 6.56 6.19 6.30 2.58 1397 mm 139.7 149.4 85.1 276.4 - - 166.6 157.2 160.0 65.6 5 5.563 5.88 3.35 10.88 - - 6.56 6.19 6.30 2.58 141.3 141.3 149.4 85.1 276.4 166.6 157.2 160.0 65.5 6.250 5.88 3.84 11.38 0.41 7.52 6.19 6.30 2.58 1 9mm 5 159.0 149.4 97.5 289.1 - 10.4 191.0 157.2 160.0 65.5 6.500 5.88 3.84 11.38 0.41 7.52 6.19 6.30 2.58 165.1mm 165.1 149.4 97.5 289.1 - 10.4 191.0 157.2 160.0 65.5 6 6.625 5.88 3.84 11.38 0.41 7.52 6.19 6.30 1.90 168.3 1 168.3 149.4 97.5 289.1 - 10.4 191.0 157.2 160.0 48.3 8 8.625 5.33 5.07 13.53 0.80 1.47 10.00 6.19 8.10 2.33 219.1 219.1 135.4 128.8 343.6 20.3 37.3 254.0 1 157.2 205.7 59.2 10 10.750 6.40 6.37 15.64 1.41 1.81 25 8.10 9.00 273 273.0 162.6 161.8 397.3 35.8 46.0 2 205.7 228.6 - 12 12.750 6.50 7.36 16.64 2.30 2.80 12 t362.0 5 8.10 9.00 323.9 323.9 165.1 186.9 422.7 58.4 71.1 205.7 228.6 - NOTE Optional 1015 mm tap available. Contact Victaulic for details. 10.81 5662 Rev G Updated 08/2016 © 2016 Victaulic Company. All rights reserved. victaulic.com . jtaUIid victaulic.com 5.0 PERFORMANCE Style 705 The chart expresses the frictional resistance of Victaulic Series 705 Butterfly Valve in equivalent feet/meters of straight pipe. Nominal Outside Equivalent Size Diameter mm mm Feet/rn inches inches of pipe 2 2.375 6 50 60.3 1.8 2½ 2.875 6 65 73.0 1.8 761 mm 371O 168 3 3.500 7 80 88.9 2.1 4 4.500 8 - 100 114.3 2.4 108 mm 108 mm 284 5 5.563 12 125 141.3 3.7 133 mm 133 mm 12 3.7 139.7 mm 5.500 12 139.7 3.7 6 6.625 14 150 168.3 4.2 159 mm 159 mm 14 43 165.1 mm 6.500 14 165.1 4.2 8 8.625 16 200 219.1 4.9 10 10.750 18 250 273.0 5.5 12 12.750 19 300 1 323.9 5.8 10.81 5662 Rev G Updated 08/2016 © 2016 Victaulic company. All rights reserved. victaulic.com 4 ',4tauiic victaulic.com 5.1 PERFORMANCE Style 705 Cv values for flow of water at +60°F/-t-160C through a fully open valve are shown in the table below. For additional details, contact Victaulic. Formulas for C values Formulas for K values AP = Q2 Where: p = Q = Flow (GPM) AP = Pressure Drop (psi) 0 = C, x C,= Flow Coefficient Q K, Valve Size Full Open Actual Nominal Outside Size Diameter Flow Coefficient inches inches c, mm mm 2 2.375 170 50 60.3 21/2 2.875 260 65 73.0 761 mm 3.000 260 76.1 3 3.500 440 80 88.9 4 4.500 820 100 114.3 108mm 108mm 820 5 5.563 1200 125 141.3 133mm 133 mm 1200 1397mm 35 1200 6 6.625 1800 150 168.3 159 mm 159 mm 1800 165.1 mm 6.500 1800 165.1 8 8.625 3400 200 219.1 10 10.750 5800 250 273.0 12 12.750 9000 300 323.9 Where: Q = Flow (ms/hr) AP = Pressure Drop (Bar) K Flow coefficient Valve Size Full Open Actual Nominal Outside Size Diameter Flow Coefficient inches inches K, mm mm 2 2.375 147 50 60.3 21/2 2.875 225 65 73.0 761 mm 3.000 225 76.1 3 3.500 380 80 88.9 4 4.500 710 100 114.3 108mm 108mm 710 5 5.563 1040 125 141.3 133 mm 133 mm 1040 139.7 mm 5.35 1040 9.7 6 6.625 1560 150 168.3 159 mm 159 mm 1560 165.1 mm 6.500 1560 165.1 8 8.625 2940 200 219.1 10 10.750 5020 250 273.0 12 12.750 7790 300 323.9 10.81 5662 Rev G Updated 08/2016 © 2016 victaulic company. All rights reserved. victaulic.com victaulic.com 6.0 NOTIFICATIONS WARNING Read and understand all instructions before attempting to install, remove, adjust, or maintain any Victaulic piping products. Depressurize and drain the piping system before attempting to install, remove, adjust, or maintain any Victaulic piping products. Wear safety glasses, hardhat, and foot protection. Failure to follow these instructions could result in death or serious personal injury and property damage. 7.0 REFERENCE MATERIALS Switch and Wiring The supervisory switch contains two single pole, double throw, pre-wired switches. (II lISTED Switches are rated: MINDUIT 10 amps @ 125 or 250 VAC/60 Hz ,WNPI ' 0.50 amps @ 125 VDC CONDUIT CwsNECTORS 0.25 amps @ 250 VDC Vs1TE NUTS Switches supervise the valve in the "OPEN" position. One switch has two #18 insulated wires per terminal, which permit complete supervision of leads (refer CREALARM EN CONTROL PANEL NEXT INDICATOR CIRCUIT TO to diagrams and notes below). The second switch SUPERE1SORY has one #18 insulated wire per terminal. This double SWITCH aT11,E NDR circuit provides flexibility to operate two electrical CONTACTRATING:0AA1125AN0 devices at separate locations, such as an indicating 2SXVAC. and an audible alarm, in the area that the valve USA AT 125 XX, TELLlight O25AT2SOVDC ORis installed. HORN VOLTAGE SOURCE A 414 insulated ground lead (green) is provided. Switch i 2 leads per terminal Switch #1 = 51 Switch 2s lletd per terminal For connection to the supervisory circuit of a UL Listed alarm control panel NOTES The above diagram shows a connection between the common terminal Switch #2 = S2 (yellow - Si and yellow-with-orange stripe —S2) and the normally closed Auxiliary switch that may be connected to auxiliary terminal (blue - Si and blue-with-orange stripe - S2(. In this example, the indicator light and alarm will stay on until the valve is fully open. When devices, per the authority having jurisdiction the valve is fully open, the indicator light and alarm will go out, cap off any unused wires (e.g. brown with orange stripe). Normally Closed: (2) Blue { Only Si (two leads per terminal) may be connected to the fire alarm control panel. Common: (2) Yellow The connection of the alarm switch wiring shall be in accordance with NFPA 72 and the auxiliary switch per NFPA 70 (NEC). Normally Closed: Blue with Orange Stripe S2 Normally Open: Brown with Orange Stripe { Common: Yellow with Orange Stripe 10.81 5662 Rev G Updated 08/20i6 © 2016 Victaulic company. All rights reserved. victaulic.com 1.1 'JtauIid victaulic.com 7.1 REFERENCE MATERIALS 10.01: Regulatory Approval Reference Guide 29.01: Terms and Conditions/Warranty 1-100: Field Installation Handbook User Responsibility for Product Selection and Suitability Each user bears final responsibility for making a determination as lathe suitability of Victaulic products for a particular end-use application, in accordance with industry standards and project specifications, and the applicable building codes and related regulations as well as Victaulic performance, maintenance, safety, and warning instructions. Nothing in this or any other document, nor any verbal recommendation, advice, or opinion from any Victaulic employee, shall be deemed to alter, vary, supersede, or waive any provision of Victaulic company's standard conditions of sale, installation guide, or this disclaimer. Intellectual Property Rights No statement contained heroic concerning a possible or suggested use of any material, product, service, or design is intended, or should be constructed, to grant any license under any patent or other intellectual property right of Victaulic or any of its subsidiaries or affiliates covering such use or design, or as a recommendation for the use of such material, product, service, or design in the infringement of any patentor other intellectual property right. The terms "Patented" or "Patent Pending" refer to design or utility patents or patent applications for articles and/or methods of use in the United Slates and/or other countries. Note This product shall be manufactured by Victaulic or to Victaulic specifications. All products to be installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations. Installation Reference should always be made to the Victaulic installation handbook or installation instructions of the product you are installing. Handbooks are included with each shipment of Victaulic products, providing complete installation and assembly data, and are available in PDF format on our website at www.victaulic.com. Warranty Refer to the Warranty section of the current Price List or contact Victaulic for details. Trademarks Victaulic and all other Victaulic marks are the trademarks or registered trademarks 01 Victaulic Company, and/or its affiliated entities, in the U.S. and/or other countries. 10.81 5662 Rev G Updated 08/2016 © 2016 Victaulic Company. All rights reserved. victaulic.com j4taUIid UL/ULC 300 psi Description The 1/4" IPS three-way female threaded valve is used to facili- tate the installation of sprinkler system pressure gauges. The valve provides for one inlet and two outlets. This design allows for replacement of the system gauge without shutting down the water supply to the sprinkler system. This design also allows Authoritys' Having Jurisdication to test system pressure with an additional gauge through the second outlet. (The second outlet is normally plugged during installation with a 1/4" IPS pipe plug.) Installation Specifications Materials: Seat - Brass Body- Brass Handwheel - Iron Sizes: 1/4" IPS Working Pressure: 400 WOG Installation of the three-way valve can be accomplished with normal field installation tools. Make sure the valve is installed according to the flow indication arrow that has Thread Sealing Tape or a suit- able pipe thread sealant such as PipeFit® Thread Sealant Paste with PTFE when in- stalling the valve. DO NOT OVERTIGHTEN THREADS. been cast into the valve body. OVERTIGHTENING MAY The most common installation CAUSE VALVE FAILURE. allows for a 1/4" IPS nipple *UUULC Listed 21R97 between the valve and the water supply being measured. This assures there will be ad- equate spacing for the sprin- kler system gauge from the riser. Use either PTFE Pipe Fire Protection Products, Inc. FPPle' 6241 Yarrow Dr., Suite A, Carlsbad, CA 92011-1541 02003-2007 Fire Protection Products, Inc For questions: 1 800 344-1822 • 1 800 344-3775 fax www.fppi.com ommeI111 A 0 0 th - SN"ATfUMN N Ra f 0111 N N Sectional Floor Control Test and Drain Valve for Systems Requiring Pressure Relief Valve TEST 1/2 ORIFICE SIZE IN. Sizes: 3/4" 1" 1 11/4" 1 11/2" 2" The AGF Model 1011 TESTANDRAIN® provides the test and express drain functions for wet fire sprinkler systems on multi-story installations requiring pressure relief (NFPA 13 and NFPA 13R). The Model 1011 features a Model 7000 Pres- sure Relief Valve with drain pipe. The Model 1011 is available in a full range of sizes (3/411 to 2) with NPT connections (BSPT available). The Model 7000 Pressure Relief Valve (UL/FM) features a flushing handle and a 175 PSI factory rating (other pressure ratings available). Complies with NFPA 13 and NFPA 13R Requirements Compact, Single-Handle Ball Valve Tamper-Resistant Test Orifice and Sight Glasses 300 PSI rated. Specifiable orifice sizes: 3/e 11 (2.8K), 7A6" (4.2K), ½ (5.6K), 17/32" (8.0K), 5/811 (11.2K, ELO), 3/4 (14.0K, ESFR), and K25 Relieves Excess System Pressure caused by Surges or Temperature Changes Shipped with Relief Valve and Bypass Drain Ports Plugged to Expedite Pressure Testing Locking Kit Available Repair kits are available for all TESTANDRAIN® valves. Kit includes: Adapter Gasket (1), Ball (1), Valve Seats (2), Stem Packing (1), and Stem Washer (1). Valve and orifice size must be specified when ordering. NOTE: It is important to note that the pressure rating of the relief valve indicates an operating range of pressure for both opening and closing of the valve. Standard relief valves are required to OPEN in a range of pressure between 90% and 105% of their rating. The valves are required to CLOSE at a pressure above 80% of that rating. The relief valve should be installed where it is easily accessible for maintenance. Care should be taken that the relief valve CANNOT be isolated from the system when the system is operational. A relief valve should NEVER have a shutoff valve or a plug downstream of its outlet. WE =rs a I 111i I SS-M1011A_V001 •06/13 TESTNDRAJN" is a registered trademark of AGF Manufacturing Inc. Model 1011 - Front View Model 1011 - Plan View I TO DRAIN Orifice Sizes /e", 7/II 1/211, 17/32!', /" ELO*, 3/4" ESFR*, and K25** Materials Handle................Steel Stem ...................Rod Brass Ball ...................... C.P. Brass Body...................Bronze Valve Seat...........Impregnated Teflon® Indicator Plate .... Steel Relief Valve.........Bronze Bypass Fittings... Brass Bypass Tubing.... Nylobraid Approvals UL and ULC Listed: (EX4019 & EX4533) FM Approved NYC-BSA No. 720-87-SM MADE IN U.S.A. IMF NOTIC!11 1iI9J1i11I C LISTED U IE '25'?&M 10 nz~ M Model 1011 A 300 PSI Bronze Ball Valve, Model 7000 Pressure Relief Valve APPROVED Factory Rated at 175 PSI with other setting available Dimensions SIZE A B C D E F G H ~' 79A6' 1½" 2/16' 35/8 3%" 11 /6" 49A6" 63/8 ' (191 mm) (37.5 mm) (57 mm) (93 mm) (86 mm) (46 mm) (117 mm) (162.5 mm) V. 79/i& 11/2" 23/16' 3%" 33/8" 113A6" 49/16" 63' (191 mm) (37.5 mm) (57 mm) (93 mm) (86 mm) (46 mm) (117 mm) (162.5 mm) 11/4" 715A6" 111A6" 29A6' 41/4 35W 115A6" 59A6' 71/2' (201 mm) (43 mm) (65 mm) (108 mm) (91 mm) (51 mm) (141 mm) (192 mm) 1½" 815A6" 113/16' 31/4" 51A6" 37,,' 25,W 81/4 ' 107.i" (227 mm) (45 mm) (81.5 mm) (127 mm) (99 MM) (67 mm) (207 mm) (2 mm 2' 81W16' 11W16" 31/4' 51A6" 3/8' 25/8 ' 81/4' 107i' (227 mm) (45 mm) (81.5mm) (127 mm) 1 (99 mm) 1 (67 mm) 1 (207 mm) (274 mm) The Model 1011 provides the following... From the 2013 Edition of NFPA 13 Chapter 8.16.2.4.1 * Provisions shall be made to properly drain all parts of the system. Chapter 8.16.2.4.2 Drain connections, interior sectional or floor control valve(s) - & 8.16.2.4.3 shall be provided with a drain connection having a minimum size as shown in Table 8.16.2.4.2. Chapter 8.16.2.4.4 Drains shall discharge outside or to a drain capable of handling the flow of the drain. Chapter A.8.17.4.2 (Wet Pipe System) test connection is permitted to terminate into a drain capable of accepting full flow.., using an approved sight test connection containing a smooth bore corrosion-resistant orifice giving a flow equivalent to one sprinkler... Chapter 8.17.4.2.2 The test connection valve shall be accessible. Chapter 8.17.4.2.4 shall be permitted to be installed in any location.., downstream of the waterflow alarm. Chapter 8.17.4.3.1 (Dry Pipe System) a trip test connection not less than 1" in diameter, terminating in a smooth bore corrosion-resistant orifice, to provide a flow equivalent to one sprinkler... Chapter 8.17.4.3.2 The trip test connection... with a shutoff valve and plug not less than 1", at least one of which shall be brass. Chapter 7.1.2 - a wet pipe system shall be provided with a listed relief valve set to operate at 175 PSI or 10 PSI in excess of the maximum system pressure, whichever is greater. Chapter 8.16.1.2.3* A listed relief valve of not less than ½" in size shall be provided on the discharge side of the pressure-reducing valve set to operate at a pressure not exceeding rated pressure of the system. Chapter A.8.16.1.2.3 - consideration should be given to piping the discharge from the (pressure relief) valve i ng L AGF Manufacturing Inc. 100 Quaker Lane, Malvern, PA 19355 A Phone: 610-240-4900 Fax: 610-240-4906 www.testandrain.com *Available on 11/4' to 2 size units only • **Available on 11/2" and 2" size units only Job Name: Architect: Engineer: Contractor: ASHCROFT® Fire Protection, Sprinkler Service Gauge Type 1005P, XUL ASME B 40.1 Grade B (±3-2-3% of span) Underwriters Laboratory listed and Factory Mutual approved Corrosion-resistant ABS case Heat-resistant polycarbonate push-in window Patented PowerFlexrM movement with polyester segment True Zero TM indication, a unique safety feature Type no.: 1005P, XUL Accuracy: ASME 840.1 Grade B (±3-2-3% of span) Size: 31/2" Case: ABS (Polycarbonate blend) Ring: None Window: Polycarbonate, push-in Dial: Black figures on white back- ground Pointer: Black, aluminum Bourdon tube: "C" shaped bronze Movement: Patented PowerFlex with polyester segment Socket: Brass Restrictor: None Ashcroft® fire protection sprinkler gauges are Underwriters Laboratory listed and Factory Mutual approved for fire protection sprinkler service. The case material on Type 1005P, XUL gauges is ABS. The 0-300 psi pressure range is used on "wet' systems where water is available to the sprinkler heads. The 0-80 retard to 250 psi pressure range is used on dry systems where the lines are filled with air pressure until system activation. The patented PowerFlex move- ment with polyester segment is designed to provide unequalled shock and vibration resistance resulting in superior performance and extended gauge life. Operating temperature: —40°F to 150°F Connection: 1/4 NPT lower Ranges: 0-300 psi (water) 0-80 retard to 250 psi (air) UL 393 Listed, UL of Canada Listed and FM approved. Equivalent (single or dual scale) metric scales are available True Zero indication, a standard feature on these gauges, reduces the potential risk of installing a dam- aged gauge on your equipment. Customized dials Other UL listed ranges on application IL1STED I <::iE~~> LOOK FOR ThESE AGENCY MARKS ON OUR PRODUCTS TO ORDER THIS TYPE 1005P, XUL GAUGE: Select: 35 W 1005 P H 02L XUL 300# Dial Size: 31/2" I Patented Poweffle)P Movement Case Type Number: 1005 Case Type Material: ABS Socket Material: Brass Connection Size/Location: ¼ NPT lower UL listed, FM approved Range: 300 psi Consult factory for guidance in product selection - Phone (203) 385-0217, Fax (203) 385-0602 or visit our web site at www.ashcroft.com Instruments SAl -000-0000 X/t ic aulicC===* ® Sprinkler Cabinets PRODUCT DESCRIPTION SA4-000-0000 Victaulic Automatic Sprin- kler Cabinets provide for storage of a supply of sprin- klers. Maintaining a supply of spare sprinklers on the premises of automatic sprinkler systems will aid in the prompt replacement of operated or damaged sprin- klers and returning a fire protection system to ser- vice as soon as possible. This is a requirement of NFPA and most Authori- ties Having Jurisdiction. Refer to the applicable NFPA standard governing your specific installation for further details. Six or twelve sprinkler capacity cabinets are avail- able. This also provides for storage of the appropriate wrench which is required for the installation and removal of sprinklers. NFPA 25 requires the total number of spare sprinklers to be stored on the pre- mises of an automatic sprinkler system meet the minimum quantities shown in the accompanying table. When the sprinkler system includes more than one type of temperature rating sprinkler, the stock of spare sprinklers must include a proportional sampling of each type and temperature rating; however, a mini- mum of 3 each is recom- mended. Sprinklers in Building Mm. Number of Spare Sprinklers Under 300 6* 300tol000 12 Over 1000 24 A minimum of three sprinklers of each type and temperature rating are required for residential fire sprinkler systems in one- and two-family dwellings and mobile homes. SA2-000-0000 L4 SA3-000-0000 I I TECHNICAL SPECIFICATIONS Models: LI 12 sprinklers o 6 sprinklers LI 3 sprinklers (NFPA/3D, Residential) O 6 large sprinklers Material: Heavy gauge steel, red enamel. Cabinets are available in six or twelve sprinkler capacities with dimensions and shelf variations as shown on page 2. The cabi- nets are of welded construction fabricated from low carbon steel sheet. The box and shelves are fabricated from 0.030' thick material and the cover is fabri- cated from 0.042' thick material. The cover is mounted to the box, at the top, with two 0.036" thick steel butt type hinges. A coat of red enamel paint is applied inside and out, and a label indi- cating that the cabinet is for spare sprinklers is bonded to the cover. VICTAULIC® IS AN ISO 9001 CERTIFIED COMPANY Victaulic Company of America Victaulic Company of Canada Victaulic Europe Victaulic America Latina Victaulic Asia Pacific Phone: 1-800-PICK-V1C (1-800-742-5842) Phone: 416-675-5575 Phone:32-9-381-1500 Phone: 610-559-3300 Phone: 65-235-3035 Fax: 610.250-8817 Fax: 416-675-5565 Fax: 32-9-380-4438 Fax: 610-559-3608 Fax: 65-235-0535 e-mail:pickvic@victaulic.com e-mail: viccanada@victaulic.com e-mail: viceuro@vicLaulic.be e-mail: vical@vicLaulic.com e-mail: vicap@viclaulic.com 2561 Rev.B 7/02 0 Registered Trademark of Victaulic 0 copyright 2002 Victaulic Printed in U.S.A. H 10'.4,111 DIMENSIONS Dimensions - Inches/millimeters Victaulic H W D Part Number Description Use With yb, V26, V29, V27, V34 (except 5.25 14.31 4.00 SAl -000-0000 For 12 Sprinklers V3403 & V3404) 133 364 102 SA2-000-0000 For 6 Sprinklers V27, V3403, V3404. V34 5.25 133 14.31 364 2.38 60 5A3-000-0000 For 3 Sprinklers (NFPA 131)) V27, V29 Residential 5.25 133 7.31 186 2.38 60 V40, V38, V39 Concealed, Kb ESFR, SA4-000-0000 For 6 Large Sprinklers All Intermediate Level Sprinklers, 6.50 14.31 3.13 All Guards 165 364 79 Specily part number and capacity when ordering. Guards will Only lit if NOT assembled to sprinkler. Capacity may be reduced. INSTALLATION Automatic Sprinkler Cabinets must be installed and the spare sprinkler stock maintained in compliance with the applicable standards of the NFPA, in addition to the standards of any other Authorities Having Jurisdiction. Failure to do so may result in property damage and impair the ability to return an automatic sprinkler system to ser- vice as soon as possible. thCAUTION The owner is responsible for maintaining a supply of spare sprinklers in proper condition. The installing contractor should be contacted with any questions. Failure to do so may result in property damage. WARRANTY Refer to the Warranty section of the current Price List or contact Victaulic for details. This product shall be manufactured by Victaulic company. All products to be installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations. 40.81 -2 F P P I Description Pipefit® Thread Sealing Paste with PTFE is a premium non-hardening PTFE filled pipe thread sealing paste designed specifically for the fire sprinkler industry. Pipefit is suitable for use on all threadable materials commonly used in fire sprinkler systems, including CPVC. Pipefit's unique blend of materials provides superior thread sealing qualities over other similarly priced sealants. The particulate PTFE also helps prevent leaks by accumulating in the voids of damaged or defective threads of the pipe or fittings. Additionally, the lubricating qualities of the PTFE and other materials in the sealing paste improve thread seating during pipe and fitting assembly. Pipefit® also adheres well to hot oily pipe present in "high speed' fabrication operations. Design Criteria/Data Recommended Use Water Air Refrigerants Natural Gas Mild caustics Steam Kerosene LP Gases Acids Gasoline Diesel Fuel Ammonia Use for threaded connections on steel, aluminum, brass, PVC, CPVC and ABS. Operating temperature ranges -50 f to 500 f. FB(V;'- SVSTM COMPA1ThIE *FBC System Compatible indicates this product has been tested by Lubrizol Advanced Materials and is monitored on an on going basis to assure chemical compatibility with FlowGuard Gold®, BlazeMaster, and Corzan® pipe and fittings. 3198 LIONSHEAD AVE CARLSBAD, CA 92010 TEL + 1760 599-1168 +1800344-1822 FAX +1 800 344-3775 Installation Make sure that the threads are free from burs and other debris. Apply Pipefit® liberally to the male pipe threads. Make sure that the thread sealant is brushed into the "root" of the threads. Do not wipe off excess material until fitting has been "made on" to the pipe thread. The threading action of the fitting to the pipe will allow the proper amount of sealant to remain in the connection. Wipe off excess sealant. Pipefit® will not dry out under normal conditions. Never use dope and tape together. Keep covered when not in use to avoid contamination. Some settling of the product may occur. Occasional stirring may be necessary. Two year shelf life. Disclaimer DO NOT ALTER THE CONSISTENCY OF THIS PRODUCT. Use as is directly from the container. Keep away from your mouth and eyes. If eye contact occurs, flush with water for 5 minutes. If discomfort persists get medical attention. Specifications Appearance: Dense, paste-like consistency, off white in color. Packaging: 16 oz. brush in cap 32 oz. 32 oz. BIC 1 gl. 5 gl. 55 gl. CAUTION: See MSDS for first aid instructions. Wash hands thoroughly after each use. See Material Safety Data Sheet for additional safety and disposal information at www.fppi.com Nu © 2012 Fire Protection Products, Inc. FPPI, LubeRt are registered trademarks of Fire Protection Products, Inc. kA FBC', BIazeMaster, FlowGuard GoIcP and Corzan are registered trademarks of Noveon IP Holdings Corp. MADE IN U.S.A. DIEGO 7635 RONSON ROAD • SAN DIEGO, CA 92111 • TEL: 858-278-3270 • FAX: 858-278-2950 E-MAIL: saIessandiegoseaI.com • VISIT US AT: www.sandiegoseal.com PTFE Thread Sealant Tapes Made in the USA Our thread sealant tape breaks clean without shredding or warping, identifying it as a product that can be trusted the :o perform reliably when the job is completed and pressure is on. Standard Grade - Our standard grade PTFE Thread Sealant Tape is for those applications that do not require the sealing properties of a . premium grade thread sealant. This is intended to be used for general purpose sealing in pipe threads. The standard (,MLW . density virgin PTFE sealant tape permits quick, clean, economical sealing of male pipe threads of all sizes and reduces the risk of system contamination common with liquid and paste sealants. High-Density Thread Sealant Tape It is effective and efficient so you can use less tape. Tears cleanly.. seals neatly Quick sealing: This premium high density PTFE sealant tape permits quick, clean sealing of male pipe threads of all sizes and eliminates the risk of system contamination common with liquid and paste sealants. Self-lubricating: The self-lubricating quality of this unsintered tape makes joints easy to assemble and disassemble, and extends the fatigue life of sealed connections. Durable: Totally maintenance free premium high density PTFE thread sealant tape is virtually chemically inert, non-toxic, non-absorbent and non-flammable. It will withstand temperatures from -450°F (-240°C) to +500°F (+260°C), and pressures from hard vacuum to 10,000 PSI. Full Density Yellow Gas Line PTFE Thread Sealant Tapes risk of system contamination common with liquid and paste sealants. Our full density premium and gas line tapes meet Mil Spec A-A 58092 for liquid & gaseous oxygen applications. The self-lubricating quality of this unsintered tape makes joints easy to assemble and disassemble. Totally maintenance free, full density PTFE thread sealant tape is virtually chemically inert, non-toxic, non-absorbent and non-flammable. It will withstand temperatures from -450°F (- 40°C) to +500°F (+260°C), and pressures from a hard vacuum to 10,000 PSI. Typical properties of PTFE thread sealant tape are as follows: Typical Properties Premium Grade Premium Grade Premium Grade - Yellow Grade Standard Grade High Density Full Density Full Density Standard Density . •.. Complies with certain Maximum sealing So efficient, building codes requiring Description The economical choice More sealing power n I yellow, thicker, more ou ca use less ~Power tense tape for gas ape. service lines Color White or colors rVhite or colors Vhite or colors "ellow Density IStandard 0.5 to 0.7 Standard 1.0 to 1.2 Standard 1.5 Standard 1.6 Thickness 0.003" to 0.0035' 0.003' to 0.0035' No .003" to 0.0035" Standard Widths & %" x 260' %" x 520" Y4"x 1296" %" x 260" 1/2-1 x 520" %" x 1296" Lengths Y4" x 260" /" x 520" /" x 1296" 1' x 260" 1" x 520" 11" x 1296" Quantity 144 rolls per box 144 rolls per 144 rolls per box box Color Typical Use fVhite All industrial applications. Made from virgin PTFE 'ink For use in plumbing and pipe fittings (water and steam lines) Gray For stainless steel pipe/fittings 3reen For oxypplIçtions (ellow For gas line use SAN DIEGO SEAL, INC / 7635 RONSON ROAD • SAN DIEGO, CALIFORNIA 92111 L7 TEL: 858-278-3270 • FAX: 858-278-2950 E-MAIL: salessandiegoseal.com • VISIT US AT: www.sandiegoseal.Com