Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
4394 YUKI LN; ; FPR2017-0261; Permit
PERMIT REPORT city of C arl Print Date: 10/24/2022 Permit No: FPR2017-0261 Job Address: 4394 YUKI IN, CARLSBAD, CA Status: Closed - Finaled Permit Type: FIRE-Construction Residential Work Class: Single Family Fire Sprinkl Parcel #: 2073605400 Track #: Applied: 06/22/2017 Valuation: $563,656.00 Lot #: Issued: 07/26/2017 Occupancy Group: Project #: DEV15035 Finaled Close Out: 04/16/2021 #of Dwelling Units: Plan #: Bedrooms: Construction Type: Final Inspection: Bathrooms: Orig. Plan Check #: INSPECTOR: Workman, Carisa Plan Check #: Fieri, Dominic Project Title: 4394 YUKI LANE Description: YUKI LANE RESIDENCE (#2) - SFD SPRINKLER <100 (39) Applicant: FPContractor: INNOVATIVE FIRE PROTECTION INNOVATIVE FIRE PROTECTION INC DERIK BROOKS 8779 COTTONWOOD AVE, # STE 101 8779 COTTONWOOD AVE SANTEE, CA 92071-4457 SANTEE, CA 92071-4457 (619) 593-8200 (619) 593-8200 FEE AMOUNT FIRE NFPA 13D Single Family System (Insp/Bldg) $121.00 FIRE NFPA 13D Single Family System (Plan Review) $239.00 Total Fees: $360.00 Total Payments To Date: $360.00 Balance Due: $0.00 Fire Department Page 1 of 1 1635 Faraday Avenue, Carlsbad CA 92008-7314 1 760-602-4665 1760-602-8561 1 I www.carlsbadca.gov HYDRAULIC CALCULATIONS for Job Information Project Name: YUKI LANE RESIDENCE Contract No. : C6696 Project Location: 4394 YUKI LANE City: CARLSBAD, CA 92008 Date: 6/21/2017 Contractor Information Name of Contractor: INNOVATIVE FIRE PROTECTION, INC. Address: 8779 COTTONWOOD AVE.,STE. 101 City: SANTEE, CA 92071 Phone Number: 619-593-8200 E-mail: DERIK@IFPINC.NET Name of Designer: DERIK BROOKS Authority Having Jurisdiction: CARLSBAD FIRE AUTHORITY Design Remote Area Name 2 Remote Area Location DEN Occupancy Classification Density (gpm/ft2) 0.052 Area of Application (ft2) 324 Coverage per Sprinkler (ft2) 324 Number of Calculated Sprinklers 1 In-Rack Demand (gpm) 0 Special Heads Hose Streams (gpm) 5 Total Water Required (incl. Hose Streams) (gpm) 22 Required Pressure at Source (psi) 40.7 Type of System Wet Volume - Entire System (gal) 33.2 gal Water Supply Information Date 5/16/2017 Location 4394 YUKI LANE Source 1 Notes File: C:\Users\William\appdata\Iocal\temp\C6696 4394 YUKI LANE_1_1_0412.sv$ Date 6/21/2017 Copyright ©2002-2o12Tyco Fire Protection Products Page 1 Job: YUKI LANE RESIDENCE Hydraulic Analysis for: 2 Calculation Info Calculation Mode Hydraulic Model Fluid Name Fluid Weight, (lb/ft3) Fluid Dynamic Viscosity, (lbs/ft2) Water Supply Parameters Supply 1: 1 Supply Analysis Demand Hazen-Williams Water @ 60F (15.6C) N/A for Hazen-Williams calculation. N/A for Hazen-Williams calculation. Flow (gpm) Pressure (psi) 0 52.6 500 47 IStatic Pressure Residual Flow I I Available I I Total Demand i Required Pressure Node at Source I (psi) I Pressure (gpm) I Pressure (gpm) (psi) (psi) I (psi) I 1 52.6 j 47 500 52.5 22 40.7 Hoses -- Inside Hose Flow! Standpipe Demand (gpm) 5 Outside Hose Flow (gpm) 0 Additional Outside Hose Flow (gpm) Other (custom defined) Hose Flow (gpm) - 0 Total Hose Flow (gpm) 5 Sprinklers Ovehead Sprinkler Flow (gpm) 17 InRack Sprinkler Flow (gpm) 0 Other (custom defined) Sprinkler Flow (gpm) 0 Total Sprinkler Flow (gpm) 17 Other Required Margin of Safety (psi) 0 1 - Pressure (psi) 40.7 1 - Flow (gpm) 22 Demand w/o System Pump(s) N/A File: C:\Users\William\appdata\Iocal\temp\C6696 4394 YUKI LANE_i _i_0412.sv$ Date 6/21/2017 Copyright©2002-2O12Tyco Fire Protection Products Page 2 Job: YUKI LANE RESIDENCE Hydraulic Analysis for: 2 File: C:\Users\William\appdata\local\temp\C6696 4394 VUKI LANE-1 _1_0412sv$ Date 6/21/2017 Copyright ©2002-2O12Tyco Fire Protection Products Page 3 Job: YUKI LANE RESIDENCE Hydraulic Analysis for: 2 Graph Labels Label Description Values Flow (gpm) Pressure (psi) Si Supply point #1 - Static 0 52.6 S2 Supply point #2 - Residual 500 47 Dl Elevation Pressure 1 0 8.2 D2 ISystem Demand 1 22 1 40.7 Curve Intersections & Safety Margins Curve Name Intersection I Safety Margin I Pressure (psi) I Flow (gpm) Pressure (psi) I @ Flow (gpm) Supply 52.5 26 I 11.9 22 Open Heads Required ___________ Calculated Head Ref. Head Type Coverage K-Factor Density Flow Pressure Density Flow Pressure (ft2) (gpm/psi'/2) (gpm/ft2) (gpm) (psi) (gpm/ft2) (gpm) (psi) 195 Overhead 324 4.9 0.05 16.2 12 0.052 17 12 Sprinkler File: C:\Users\Williamappdata\local\temp\C6696 4394 YUKI LANE_1_1_0412.sv$ Date 6/21/2017 Copyright© 2002-2012 Tyco Fire Protection Products Page 4 Job: VUKI LANE RESIDENCE Hydraulic Calculations / Fluid Delivery Time Analysis Node Data Node# Type K-Fact. Discharge Coverage Tot. Pres. Req. Pres. Elev Hgroup Open/Closed Overdischarge Density Elev. Pres. Req. Discharge gpm/psi1/2 gpm ft2 psi psi ft gpm gpm/ft2 psi gpm 195 Overhead Sprinkler 4.9 17 324 12 12 16 HEAD Open 0.8 0.052 -8.2 16.2 021 Node 11.1 28 NODE -13.4 063 Node 11.3 28 NODE -13.4 015 Node 11.3 28 NODE -13.4 027 Node 15.6 17 NODE -8.7 031 Node 16.5 17 NODE -8.7 038-0 Node 18.7 14.02 NODE -7.4 038-I Node 20.3 13.52 NODE -7.2 039 Node 22 10 NODE -5.6 041 Node 23.5 7 NODE -4.3 G5 Inside Hose 5 23.5 7 HOSE -4.3 5 043 Node 23.5 7 NODE -4.3 046-0 Node 28.2 -3 NODE 0 046-I Node 33.3 -3 NODE 0 047-0 Node 33.6 -3 NODE 0 047-I Node 37.6 -3 NODE 0 1 Supply -22 40.7 -3 SUPPLY 0 File: C:\Users\Williamappdata\local\tempC6696 4394 YUKI LANE _1_1_0412.sv$ Date 6/21/2017 Copyright © 2002-2012 Tyco Fire Protection Products Page 5 Job: YUKI LANE RESIDENCE Hydraulic Calculations / Fluid Delivery Time Analysis Pipe Data Path # Type Schedule HWC Fittings Length Flow Fr.Resist. Vel.Pres. Start Pipe Ref. Hgroup Size Rough. Eq.Len. Total Len. Velocity Loss Frict. Loss Elev. End It gpm psi/ft psi in It It ft/s psi psi 1 Brline CPVC 150 6(BM.Tee-Run);3(BM.Tee-Br);1(BM 49.19 17 0.05 0.2 027 022 PIPE 1 0.000084 .45);2(BM.90); 81.19 5.72 4.1 -0.4 195 32 1 Brline CPVC 150 3(BM.Tee-Run); 1(BM.90); 1(BM.45) . 33.87 10.2 0.0195 0.1 031 027 PIPE 1 0.000084 ' 9 42.87 3.44 0.8 0 027 1 Cmain CPVC 150 1(coupling); 1(BM.90);4(BM.Tee-Ru 41.13 17 0.0158 0.1 038-0 034 PIPE 1.25 0.000084 n);1(BM.Tee-Br); 58.71 3.57 0.9 1.3 031 17.59 1 VALVE BRASS RESI 0 0.5 17 2.8889 0 038-I 144 VALVE 1.25 0 0 1.4 0.2 038-0 1 Cmain CPVC 150 1(coupling); 3.52 17 0.0158 0.1 039 035 PIPE 1.25 0.000084 1.59 5.11 3.57 0.1 1.5 038-1 1 Cmain Copper L 150 1(coupling);1(us.90); 4 17 0.0254 0.1 041 037 PIPE 1.25 0.000084 3.95 7.95 4.33 0.2 1.3 039 1 Cmain PVC150 150 1(us.Tee-Run);1(us.90); 3.56 17 0.0023 0.0 043 039 PIPE 2 0.000084 7.55 11.11 1.62 0.0 0 041 1 Cmain PVC150 150 1(coupling); 1(us.90); 1(us.45); 91.54 22 0.0038 0.0 046-0 042 PIPE 2 0.000084 12.08 103.62 2.1 0.4 4.3 043 1 BFP WILKINS 950XL 0 0.5 22 10.2818 0 046-I 146 BFP 1 0 0 5.1 0 046-0 1 Cmain Copper L 150 1(coupling); 0.56 22 0.1143 0.5 047-0 043 PIPE 1 0.000084 1.35 1.91 8.54 0.2 0 046-1 1 VALVE WATER METER 4 0 0.5 22 8 0 047-I 145 VALVE 1 0 0 4 0 047-0 1 Cmain Copper K 150 23.59 22 0.1321 0.6 1 044 PIPE 1 0.000084 9.07 3.1 0 047-1 2 Cmain PVC150 150 1(us.Tee-Br); 0.63 5 0.0002 0 043 045 PIPE 2 0.000084 15.1 15.73 0.48 0 0 G5 3 Brline CPVC 150 2(BM.Tee-Br);1(BM.90); 14.38 6.8 0.0091 0.0 021 088 PIPE 1 0.000084 15 29.38 2.28 0.3 -4.8 027 3 Brline CPVC 150 4(BM.Tee-Run);1(BM.Tee-Br);1(BM 35.13 4.2 0.0037 0.0 015 081 PIPE 1 0.000084 .90) 49.13 1.41 0.2 0 021 14 3 Brline CPVC 150 1(BM.Tee-Run);2(BM.Tee-Br);2(BM 21.44 6.8 0.0091 0.0 031 054 PIPE 1 0.000084 . .90), 42.44 2.28 0.4 4.8 015 21 4 Brline CPVC 150 6(BM.Tee-Run);3(BM.Tee-Br);2(BM 75.58 2.6 0.0015 0 063 064 PIPE 1 0.000084 .90); 106.58 0.87 0.2 0 021 31 4 Brline CPVC 150 1(BM.Tee-Run);1(BM.Tee-Br); 8.53 2.6 0.0015 0 015 060 PIPE 1 1 0.000084 6 14.53 0.87 0.0 0 063 File: C:\Users\William\appdata\local\temp\C6696 4394 YUKI LANE_1_1_0412.sv$ Date 6/21/2017 Copyright © 2002-2012 Tyco Fire Protection Products Page 6 Job: VUKI LANE RESIDENCE Hydraulic Calculations I Fluid Delivery Time Analysis Pipe Data Start Disch. Start Tot. Pres. End Disch. End Tot.Pres. gpm psi gpm psi 15.6 17 12 16.5 15.6 18.7 16.5 20.3 18.7 22 20.3 23.5 22 23.5 23.5 28.2 23.5 33.3 28.2 33.6 33.3 37.6 33.6 22 40.7 37.6 23.5 5 23.5 11.1 15.6 11.3 11.1 16.5 11.3 11.3 11.1 11.3 11.3 File: C:\Users\Williamappdata\local\temp\C6696 4394 YUKI LANE_1_1_0412.sv$ Date 6/21/2017 Copyright© 2002-2012 Tyco Fire Protection Products Page 7 Job: YUKI LANE RESIDENCE Hydraulic Calculations PIPE INFORMATION Node 1 Elev 1 K-Factor 1 Flow added (q) Nominal ID Fittings L C Factor total (Pt) Node 2 Elev 2 K-Factor 2 Total flow (Q) Actual ID quantity x (name) = length F Pf per ft elev (Pe) NOTES T frict (Pf) (ft) (gpm/psil/2) (gpm) (in) (ft) (ft) (psi) (psi) Path No: I 195 16 4.9 17 1 6x(BM.Tee-Run)=6 49.19 150 12 027 17 17 1.101 3x(BM.Tee-Br)=15 32 0.05 -0.4 lx(BM.45)=1 81.19 4.1 2x(BM.90)=10 027 17 -6.8 1 3x(BM.Tee-Run)=3 33.87 150 15.6 031 17 10.2 1.101 lx(BM.90)=5 9 0.0195 0 lx(BM.45)=1 42.87 0.8 031 17 6.8 1.25 lx(coupling)=1.59 41.13 150 16.5 038-0 14.02 17 1.394 lx(BM.90)=6 17.59 0.0158 1.3 4x(BM.Tee-Run)=4 58.71 0.9 lx(BM.Tee-Br)=6 038-0 14.02 0 1.25 0.5 0 18.7 BRASS RESI 038-1 13.52 17 0 0 2.8889 0.2 0.5 1.4 038-1 13.52 0 1.25 lx(coupling)=1.59 3.52 150 20.3 039 10 17 1.394 1.59 0.0158 1.5 5.11 0.1 039 10 0 1.25 lx(coupling)=0.99 4 150 22 041 7 17 1.265 lx(us.90)=2.97 3.95 0.0254 1.3 7.95 0.2 041 7 0 2 lx(us.90)=7.55 3.56 150 23.5 043 7 17 2.067 7.55 0.0023 0 11.11 0.0 043 7 5 2 lx(coupling)=1.51 91.54 150 23.5 046-0 -3 22 2.067 lx(us.90)=7.55 12.08 0.0038 4.3 lx(us.45)=3.02 103.62 0.4 046-0 -3 0 1 0.5 0 28.2 WILKINS 046-1 -3 22 0 0 10.2818 0 950XL 0.5 5.1 046-I -3 0 1 lx(coupling)=1.35 0.56 150 33.3 047-0 -3 22 1.025 1.35 0.1143 0 1.91 0.2 047-0 -3 0 1 0.5 0 33.6 WATER METER 047-I -3 22 0 0 8 04 0.5 4 047-1 -3 0 1 23.59 150 37.6 1 -3 22 0.995 0 0.1321 0 23.59 3.1 1 40.7 Path No: 2 G5 7 5 2 lx(us.Tee-Br)=15.1 0.63 150 23.5 043 7 5 2.067 15.1 0.0002 0 15.73 0 043 23.5 File: C:\Users\William\appdata\IocaI\temp\C6696 4394 YUKI LANE_i_i _0412.sv$ Date 6/21/2017 Copyright© 2002-2012 Tyco Fire Protection Products Page 8 Job: YUKI LANE RESIDENCE Hydraulic Calculations PIPE INFORMATION Path No: 3 027 17 0 1 2x(BM.Tee-Br)=10 14.38 150 15.6 021 28 6.8 1.101 lx(BM.90)=5 15 0.0091 -4.8 29.38 0.3 021 28 -2.6 1 4x(BM.Tee-Run)=4 35.13 150 11.1 015 28 4.2 1.101 lx(BM.Tee-Br)=5 14 0.0037 0 lx(BM.90)=5 49.13 015 28 2.6 1 1x(BM.Tee-Run)=1 21.44 150 11.3 031 17 6.8 1.101 2x(BM.Tee-Br)=10 21 0.0091 4.8 2x(BM.90)=10 42.44 0.4 031 16.5 Path No: 4 021 28 0 1 6x(BM.Tee-Run)=6 75.58 150 11.1 063 28 2.6 1.101 3x(BM.Tee-Br)=15 31 0.0015 0 2x(BM.90)=10 106.58 0.2 063 28 0 1 1x(BM.Tee-Run)=1 8.53 150 11.3 015 28 2.6 1.101 lx(BM.Tee-Br)=5 6 0.0015 0 14.53 0.0 015 11.3 * Pressures are balanced to a high degree of accuracy. Values may vary by 0.1 psi due to display rounding. * Maximum Velocity of 9.07 ft/s occurs in the following pipe(s): (1-047-I) " Device pressure loss (gain in the case of pumps) is calculated from the device's curve. If the device curve is printed with this report, it will appear below. The length of the device as shown in the table above comes from the CAD drawing. The friction loss per unit of length is calculated based upon the length and the curve-based loss/gain value. Internal ID and C Factor values are irrelevant as the device is not represented as an addition to any pipe, but is an individual item whose loss/gain is based solely on the curve data. File: C:\Users\William\appdata\localtemp\C6696 4394 YUKI LANE_1_1_0412.sv$ Date 6/21/2017 Copyright © 2002-2012 Tyco Fire Protection Products Page 9 1 Job: YUKI LANE RESIDENCE Device Graphs Pressure vs. Flow Function Design Area: 2; Supply Ref.: 1; Supply Name:1 o 0 0 0 0 0 00 0 0 0 0 N N 00 00 Flow, gpm Pressure Loss Function Design Area: 2; BFP Ref.: 146 (WILKINS 950XL, Size = 1); Inlet Node: 046-I; Outlet Node: 046-0 0 0 0 e 0 0 0 - N 00 00 00 00 Flow, gpm File: C:\Users\WilIiam\appdata\IocaI\tempC6696 4394 YUKI LANE_1_1_0412.sv$ Date 6/21/2017 Copyright© 2002-2012 Tyco Fire Protection Products Page 10 3 3 2 0 0 Job: YUKI LANE RESIDENCE Device Graphs Pressure Loss Function Design Area: 2; Valve Ref.: 144 (BRASS RESI, Size = 1.25); Inlet Node: 038-I; Outlet Node: 038-0 4.5 1.4 psi @17gpm 1.5 0.5 Flow, gpm Pressure Loss Function Design Area: 2; Valve Ref.: 145 (WATER METER 4, Size = 1); Inlet Node: 047-I; Outlet Node: 047-0 0 0 en 'In Flow, gpm File: C:\Users\William\appdata\IocaI\temp\C6696 4394 YUKI LANE_1_1_0412.sv$ Date 6/21/2017 Copyright © 2002-2012 Tyco Fire Protection Products Page 11 SPE(FICATI ON SUBMITTAL SHEET : :i FEATURES Sizes: 03/4" U 1" U 1-1/4" U 1-1/2" U 2' Maximum working water pressure 175 PSI Maximum working water temperature 180°F Hydrostatic test pressure 350 PSI End connections Threaded ANSI B1.20.1 OPTIONS (Suffixes can be combined) U - with full port QT ball valves (standard) U L - less ball valves U U - with union ball valves U S - with bronze "v" type strainer U TCU - with test cocks vertical up U V - with union swivel elbows (3/4" & 1") U OSY - with OS & Y gate valves U FDC - with fire hydrant connection (2" only) U FT - with integral male 45° flare SAE test fitting APPLICATION Designed for installation on potable water lines to protect against both backsiphonage and backpressure of polluted water into the potable water supply. Assembly shall provide protection where a potential health hazard does not exist. STANDARDS COMPLIANCE (All sizes approved horizontal. Vertical approvals as listed below.) ASSE® Listed 1015 (vertical 3/4", 1 1/4", 1 1/2" & 2") IAPMO® Listed (vertical 1 1/4-2") CSA® Listed (vertical 3/4", 11/4", 1 1/2" & 2") AWWA Compliant C510 (vertical 3/4") UL® Classified (less shut-off valves only) C-UL® Classified (less shut-off valves only) Approved by the Foundation for Cross Connection Control and Hydraulic Research at the University of Southern California (vertical 3/4") City of Los Angeles Approved (vertical 1-1/4"-2') NYC MEA 426-89-M VOL 3 MATERIALS Main valve body Cast Bronze ASTM B 584 Access covers Cast Bronze ASTM B 584 Internals Stainless Steel, 300 Series Elastomers Silicone (FDA approved) Buna Nitrile (FDA approved) Polymers NorylTM, NSF Listed Springs Stainless steel, 300 series t~C ACCESSORIES URepair kit (rubber only) UThermal expansion tank (Model WXTP) U QT-SET Quick Test Fitting Set U Test Cock Lock (Model TCL24) D DIMENSIONS & WEIGHTS (do not include pkg.) B A G DIMENSIONS (approximate) WEIGHT MODEL A UNION LESS WITH SIZE A BALL B LESS BALL C D E F G BALL BALL VALVES VALVES E VALVES VALVES in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm lbs kg lbs. kg 3/4 20 111/4 286 121/2 318 7 178 11/2 38 3 76 31/2 89 3 76 15 381 5 2.3 7 3.2 1 25 121/4 311 137/8 353 7 178 11/2 38 3 76 31/2 89 3 76 173/4 451 8 3.6 12 5.4 11/4 32 15 1/2 419 18 1/2 470 109/16 268 2 51 31/2 89 4 1/2 114 41/2 114 211/2 546 16 7.3 22 10 1 1/2 40 171/8 435 191/8 486 109/16 268 2 51 31/2 89 4 1/2 114 4 1/2 114 22 3/4 578 16 7.3 22 10 2 50 18 1/4 460 20 508 109/16 268 2 51 31/2 89 41/2 114 41/2 114125 1/8 638 16 7.3 28 12.7, DOCUMENTM REVISION: BF-950XL 7112 Page 1 of 2 WILKINS a Zurn company, 1747 commerce Way, Paso Robles, cA93446 Phone:805-238-7100 Fax:805-238-5766 In Canada: ZURN INDUSTRIES LIMITED, 3544 Nashua Dr., Mississauga, Ontario L4V 11-2 Phone: 905-405-8272 Fax:905.405-1292 Product Support Help Line: 877-BAcKFLOW (877-222-5356) Website: http:/!www.zurn.com 3.2 6.3 9.5 12.6 15.8 103 . (1) LU 60 50 100 150 200 250 °- 15 10 0'- 0 1ÜTfD :=::-='• FLOW CHARACTERISTICS MODEL 950XL 3/4",1",1 1/4",1 1/2" & 2" (STANDARD & METRIC) FLOW RATES (Ifs) FLOW RATES (GPM) 0 Rated Flow (Established by approval agencies) TYPICAL INSTALLATION Local codes shall govern installation requirements. To be installed in accordance with the manufacturer's instructions and the latest ed ition of the Uniform Plumbing Code. Unless otherwise specified, the assembly shall be mounted at a minimum of 12" (305mm) and a maximum of 30" (762mm) above adequate drains with sufficient side clearance for testing and maintenance. The installation shall be made so that no part of the unit can be submerged. Capacity thruSchedule 40 Pipe Pipesize 5ft/sec 7.5ft/sec lOft/sec 15ft/sec 1/8 1 1 2 3 1/4" 2 2 3 5 3/8' 3 4 6 9 1/2 5 7 9 14 3/4" 8 12 17 25 13 20 27 40 1 1/4" 23 35 47 70 1 1/2" 32 48 1 63 1 95 1 52 1 78 105 167 DIRECTION OF FLOW OUTDOOR INSTALLATION INDOOR INSTALLATION SPECIFICATIONS The Double Check Valve Backflow Preventer shall be ASSE® Listed 1015 approved, and supplied with full port ball valves. The main body and access covers shall be bronze (ASTM B 584), the seat rings and all internal polymers shall be NSF® Listed NoryITM and the seat disc elastomers shall be silicone. The first and second checks shall be acces- sible for maintenance without removing the device from the line. The Double Check Valve Backflow Preventer shall be a WILKINS Model 950XL. WILKINS a Zurn company, 1747 Commerce Way, Paso Robles, CA 93446 Phone: 805-238-7100 Fax:805-238-5766 IN CANADA: ZURN INDUSTRIES LIMITED, 3544 Nashua Dr., Mississauga, Ontario L4V 11_2 Phone: 905-405-8272 Fax:905-405-1292 Product Support Help Line: 877-BACKFLOW (877-222-5356) Website: http://www.zurn.com Page 2 of 2 National Fire Products, LLC RESI-RISERTM The RESI-RISERTM is a pre-assembled, compact, attractive fire sprinkler riser unit for residential sprinkler systems in accordance with NFPA 13, 13R and 13D. The RESI-RISERTM manifold is manufactured as a one- piece casting that is air-tested for leaks. Raised lettering on both sides allows the RESI-RISERTM to be installed to the right or left and easily identifies the flow direction and Test and Drain outlet. Two mounting legs are molded onto the manifold allowing for a secure right or left anchoring. The flow switch has dual SPOT switches and a retard of 0-90 seconds. An optional "all in one cost saving combination Pressure Relief Valve/Test and Drain Valve is available. The RESl-RISERTM unique design gives the ability to be installed within standard 2 x 4 frame construction. Every size RESl-RISERTM fits within a 2 x 4 wall framed at 16 inches on center. Technical Data Sizes: 1", 1%", 1W', and 2" Style: Thread x Thread Listing: Flow Switch and Pressure Gauge are UL Listed Finish (Riser Body): Cast Brass Water Pressure Gauge: 0-300 psi Optional Accessories: 175 psi Pressure Relief Valve/Test and Drain US Patent # 6,076,545 Item Description 1 Manifold Body, Male Thread x Male Thread 2 Inline Check Valve, Spring Loaded 3 Flow Switch with Retard 4 Drain Valve, with optional pressure relief valve 5 Pressure Gauge, 0-300 psi RESI-RISERTM Size Chart Description 1" 114,, 1W' 2" Height* 13" 13" 13" 13" Width** 10-3/4" 11-1/2" 12" 12-1/2- Depth 3-1/2" 3-1/2" 3-1/2" 3-1/2" Drain Size 1/2-----77 1" 1" Dimensions include all spacing needed to operate drain valve and remove flow switch cover * Without check valve ** With or without pressure relief valve © National Fire Products, LLC (800) 528-7978 Pressure Loss Tables Pressure Loss in lit Resi-Riser 12 i Relieving Pressure Exceeding 175 psi 0 10 15 20 25 30 35 40 Flow (gpm) Pressure Loss in 1-1/4" Resi-Riser &. 00111111111 _-________-a 11 ------ No 0 10 15 20 25 30 35 40 45 50 55 60 Flow (gpm) Pressure Relief/Test and Drain How it Works Normal Position - L_J Static Pressure Pressure Loss in 1-1/2" Resi-Riser 10 Manual Open - Drain r Flow Switch Test iL 0 10 15 20 25 30 35 40 45 5055 6065 7075 80 Flow (gpm) Pressure Loss in 2" Resi-Riser L Closed for Hydrostatic Test fr 6 0 15 25 35 45 55 65 75 85 95 Flow (gpm) 0 National Fire Products, LLC (800) 528-7978 -- Fl Res 30,49,58&76 F1 Res 30, 49, 58 & 76 Recessed Pendent / Fl Recessed Pendent / FP Bulletin 135 Rev. M Types: 00 C 0 01 01 CD Fl Res 30Pendent Fl Res 30 Recessed PendentJF2 Fl Res 30 Recessed Pendent/FP Fl Res 49 Pendent Fl Res 49 Recessed Pendent/F1 Fl Res 49 Recessed Pendent/FP Fl Res 58 Pendent Fl Res 58 Recessed Pendent/El Fl Res 58 Recessed Pendent/FP 10, Fl Res 76Pendent Fl Res 76 Recessed Pendent/Fl Fl Res 76 Recessed Pendent/FP Fl Res 30 CCP Pendent Fl Res 49 CCP Pendent Fl Res 58 CCP Pendent Fl Res 76 CCP Pendent Fl Res 44HSW 18, Fl Res 44 Recessed HSW/F2 Fl Res 58HSW Fl Res 58 HSWX KRes58 HSWX Fl Res 58 HSW Recessed HSW/F2 Fl Res 44 SWC Listings & Approvals 1. Listed by Underwriters Laboratories Inc. and UL Certified for Canada (cULus) Sprinklers for .10 Density: Refer to Bulletin 176 UL Listing Category Residential Automatic Sprinkler UL Guide Number VKKW Patents US Patent No. 6,516,893 applies to the Mode! Fl Res 49 & 58 Pendent Sprinklers US Patent No. 7,353,882 applies to Model Fl Res 44 & 58 HSW Sprinklers US Patent No. 7,784,555 applies to Model Fl Res 44 SWC Sprinklers Product Description Model Fl Res Pendent sprinklers (Figs. 1, 2, 3, & 4) are fast response sprinklers combining excellent durability, high sensitiv- ity glass-bulb and low profile decorative design. The Fl Res Fl Res 58 Fl Res 44&58 Fl Res 44SWC Recessed HSW/F2 Horizontal Sidewall sprinklers (Figs. 5, 6 & 7) are equally attrac- tive when above ceiling piping cannot be used. The 3mm glass-bulb pendent sprinklers permit the efficient use of residential water supplies for sprinkler coverage in residential fire protection design. The low flow Fl Res sprinklers are specially engineered for fast thermal response to meet the sensitive fire protection applica- tion needs of the latest residential market standards (UL 1626 Standard). Upon fire conditions, rising heat causes a sprinkler's heat-sensitive element, glass bulb or link to actuate, releasing the waterway for water flow onto the deflector, evenly distributing the discharged water to control a fire. Technical Data: Thermal Sensor: Soldered Element (Link) or Nominal 3mm glass-bulb Sprinkler Frame: Brass Casting Sprinklers' Pressure Rating : 175 psi Factory Hydrostatically Tested to 500 psi Thread Size: ½" NPT (R½) K-Factor: 3.0 (43.2) (Actual) - Fl Res 30 Pendent Sprinkler 4.9 (70.6) (Actual) - Fl Res 49 Pendent Sprinkler 5.8 (83.5) (Actual) - Fl Res 58 Pendent & HSW Sprinkler 7.6 (109)(Actual) - Fl Res 76 Pendent Sprinkler 4.4(63) (Actual) - Fl Res 44 HSW Sprinkler Density: Minimum 0.05 gpmlft2 Fl Res 30, 49, 58 & 76 CCP Pendent Reliable Automatic Sprinkler Co., Inc., 103 Fairview Park Drive, Elmsford, New York 10523 Model Fl Res 30. 49, 58 & 76 Pendent Model Fl Res 30 Recessed Pendent / F2 Moth lent/Fl Application Model Fl Res Sprinklers are used for Residential Fire Pro- tection according to UL 1626 Standard*. For ceiling types: Smooth Flat Horizontal, or beamed, or sloped, in accordance with NFPA 130, 13R, or 13 2013 editions. Be sure that orifice size, temperature rating deflector style and sprinkler type are in accordance with the latest published standards of The Na- tional Fire Protection Association or the approving authority having jurisdiction. Installation Models Fl Res sprinklers are to be installed as shown. Model Fl, F2 and FP Escutcheons, illustrated herewith, are Escutcheon*. Fl or F2. Data: the only recessed escutcheons to be used with Model Fl Res sprinklers. Use of any other recessed escutcheon will void all approvals and warranties. For installing Model Fl Res Pen- dent sprinklers use only the Model D sprinkler Wrench; for installing Models Fl Res Recessed Pendent, COP & SWC sprinklers use only he Model GFR2 sprinkler wrench; for in- stalling Model Fl Res Recessed HSW sprinklers use only the Model GFR2 Sprinkler Wrench. Use of wrenches other than those specified may damage these sprinklers. Install Fl Res 44 with a ceiling to deflector distance of 4" - 12". Flow arrow on deflector must point away from near wall and "Top" mark- ing must face ceiling. Type Adjustment "A" Face Deflector Distance below bottom of beam Inch (mm)Inch Inchmm) (mm) Inch (mm) Fl 3/4 (19.0 Mm. Recessed = 1/s (41.3) 3/8 (9.5) 1/4 (44.4) Max. Recessed =/(22.2) 11/8 (28.6) 1 (25.4) F2 1/ 12 7\ 2 . Mm. Recessed = 1/e (41.3) 3/s (9.5) 1/4 (44.4) / Max. Recessed =11/8 (28.6) /e(22,2) 11/i (317) * Note: Escutcheons Fl or F2 may be used with Model Fl Res 49, 58 & 76 Recessed Pendent Sprinkler I-i escutc-neon, (it)mm) aajustmeni 2 1/4" HOLE CIA iA ,49 "URN COLLAR UNTIL TIGHT AGAINST PRWKLER WRENCH Ross. FACE OF To F! ESCU.ICHLO AOJiiILTMENT l. 2 27/32" 014. 35/303 [72.2mmJ Fig. 1 Fig. 2 Technical Data: Fl Res 30 Pendent and Recessed Pendent (SIN R351 1) Thread Nominal Orifice Max. Pressure Sprinkler Temp. Rating Max. Ambient Temp.1 Actual K Sprinkler Length Size Inch (mm) psi (bar) _OF C Factor .------------Inch (mm (R½) 21/54" (8,2) 175 (12) 155 68 100 175 t 79 38 3.0 (43.2) 2.25 (57) Max Ordinary Temp. Rating Intermediate Temp. Rating Minimum Max. Coverage area (155°F168°ç) (175°F/79°C) Top of Deflector to Ceiling Flow Pressure Flow Pressure ( Spacing Inch (mm)Ft Ft x Ft (m x m) m, GPM(Llmin' PSi(ka GPM(LJmin) . (!'a.r ----------------------.. - - .... 12 x 12 (3,6 x 3,6) 12(3,6) 8(30.3) 7.0 (0.48) 8(30,3) 7.0(0,48) Smooth ceilings 114 to 4(31.7 to 102) using F2 escutcheon. Beamed ceilings per NFPA 13D, 13R or 13 installed in beams 11/4 to 14.' 8(2,4) 14 x 14(4,3 x 4,3) 14(4,3) 10 (37.8) 11(0,76) 10(37,B) 11(0,76) 16x16 (4,9 x 4,9) 16 (49) 13(49) 18.8(13) 13(49) 18.8(1,3) (31.7to44.4) using F2C-------e0n - For Ceiling types refer to NFPA 13, 13R or 13D 2. Technical Data: Fl Res 49 Pendent and Recessed Pendent (SIN R3516) Thread Max. Sprinkler Max. Nominal Orifice Actual Sprinkler Size Pressure Temp. Rating 1 Ambient Temp. Inch (mm) ..p•(bar K Length °C Factor In hinL '/2"NPT 155 68 100 38 175 (12) 175 79 150 66 4-9(70.6) 2.25 (57) Ordinary Temp. Rating Intemiediate Temp. Rating To of Deflector Minimum Max. Coverage area Max. Spacing 155 C) (175°F/79°C)to Ft x Ft (mx m) Ft (m) Flow Pressure Ceiling Pressure in pac g Row PSI (bar) _Fllk?L Inch (mm) Ft (m) 12 x 12 (3,6 x 3,6) 12(3,6) 13 (49) 7.0 (0,48) 13 (49) 7.0 (0,48) Smooth Ceilings 11/4 to 4 (31.7 to ........- .. ....................................................LGMJlJ!ii . 102)using F2 escutcheon. 14 x 14(4,3 x 4,3) 14(4,3) 13(49) 7.0 (0,48) 13(49) 7.0(0,48) 1 t04(25,4 to 102)using Fl --- -- escutcheon. 16 x 16(4,9 x 4,9) 16(4.9) 13(49) .............. 7.0 (0.48) 13(49) TO (0,48) Beamed Ceilings per NFPA 130, 13R or 13 installed in 8(2,4) . ______.. ------------ 18 18(5,5 x 5,5) .. ....... ........_. 18(5,5) 17(64,3) 12 (0,83) 17(64,3) 12(0,83) beams 1/4t0 1~ (31.7t0 44.4) using F2 escutcheon, 1 .......................... 21) x 20(6,1 x 6,1) --..............................................................-- 20(6,1) 20(75,7) 16.7 (1,14) 20 (75,7) 16,7(1,14) to 134(25.4t044.4) using Fl ________ escutcheon For Coiling types rotor to NFPA 13, 138 or 130 Ordinary Temp. Rating Intetmediate Temp, Rating Top of Deflector Minimum 'Max. Max. Coverage area Spacing (155°F,8°C) (175°F/79°C) FtxFt(mxm) Ft (m) to Ceiling Spacing Row Pressure Row Pressure ___ GPM (Llmin) PSI (bar) GPM (Llmin) PSI (bar) Inch (mm) Ft (m) 12 x 12 (3.6 x 3,6) 12(3,6) 15 (57) 9.4 (0,65) 15(57) 9.4 (0,65) Smooth Ceilings 4 to 8 (100 to 203) using F2 escutcheon. 14 x 14(4,3 x 4,3) 14(4,3) 16(60,5) 10.6 (0,73) 16(60,5) 10.6 (0,73) 4 to 8(100 to 203) using Ft escutcheon. 16 X 16 (4.9 X 4,9) 16(4,9) 17(64,3) 12.0 (0,83) 17(64,3) 12.0(0,83) Beamed Ceilings per NFPA 130, 138 or 13 installed in beams 8 (2.4) 18 X 18(5.5 X 5.5) 18(5,5) 19(72) 15.0 (1 .0) 19(72) 15.0 (1,0) 41,4 to 8(108 to 203) using F2 escutcheon. 4108(100 to 203) Fl escutcheon 20 x 20 (6,1 x 6,1) 20(6,1) 22 (83,2) 20.2 (1,4) 22(83,2) =(1.4)using Technical Data: F1 Res 58 Pendent and Recessed Pendent (SIN R3513) Thread Max. Sprinkler Max. Nominal Orifice Pressure Temp. Rating Ambient Temp. Actual Sprinkler Length Size Inch (mm) psi , (bar) F C °F K Factor Inch (mm) 112" NPT (8½) 155 V (13) I 175 (12)175 68 100 79 150 38 66 58(835) 225(57) Ordinary Temp. Rating Intermediate Temp. Rating To of Deflector Minimum Max. Coverage area Max. Spacing (155°Fi8°C) (175°F/190C) Ft x Ft (mx m) Ft (m) Flow Pressure Ceiling in c g Row Pressure GPM (tlmin) PSI (bar) GPM (Llmin) PSI (bar) Inch (mm) Ft (m) 12 x 12(3,6 x 3,6) 12(3.6) 16(61) - 7.6 (0,53) 16(61) 7.6 (0,53) Smooth Ceilings 11/4 104(31.710 102) using F2 escutcheon. 14 x 14(4,3 x 4,3) - ...................... ........... 14(4,3) 16(61) "" 7.6 (0,53) 16 (61) 7.6 (0,53) 1 t 4(25.410 102) using Fl escutcheon. 16 x 16(4,9 x 4,9) 16(4.9) 16(61) 7.6 (0,53) 16(61) 7.6 (0,53) Beamed Ceilings per NFPA 130, 13R or 13 installed in beams 8(2,4) 18 x 18(5,5 x 5,5) 18(5.5) 1 19(72) 10.8 (0,75) 19(72) 10.8(0.75) 1¼ to 1114 (31.7 t044.4) using F2 escutcheon, 1 t 13/4 (25.4 to 20 x 20 (6,1 x 6,1) 20(6.1) 22 (83,3) 14.4 (1,0) 22 (83,3) 14.4 (1,0) 44.4) using Fl escutcheon For Ceiling types refer to NFPA 13, 13R or 130 Technical Data: Fl Res 76 Pendent and Recessed Pendent (SIN R7618) Thread Nominal Orifice Max. Sprinkler F Max K Sprinkler Size Inch (mm) Pressure Temp. Rating Ambient Temp Length psi (bar) Factor nç.h(nin'J 3/ FT /32" (13.5) 175(12) 155 175 68 79 100 150 38 7.6 (109) 66 2.25 (57) Ordinary Temp. Rating Intermediate Temp. Rating Minimum Max. Coverage area Max. Spacing (1550FI8°C) (175°F179°C) Top of Deflector to Ceiling Spacing Flow Pressure 1 Flow GPM Pressure Ft x Ft (mx m) Ft (m) Inch (mm) GPM (1/mm) PSI (bar) 1 (1/mm) PSI (bar) 12x 12(3,6x3,6) 12(3,6) 21(795) 7.6(0153) 21(79,5) 7.6(0,53) Smooth Ceilings 41/4 to8( 08 to 203) using F2 escutcheon. 14 x 14 (4,3 x 4,3) 14(4,3) 21(79,5) 7.6 (Q53) 21(79,5) 7.6(0,53) 4 to 8(100 to 203) using Fl escutcheon. Beamed Ceilings per NFPA 13D, 13R or 13 installed in 8(2,4) 16 x 16 (4,9 x 4,9) 16(4,9) 21(79,5) 7.6(0,53) 21(79,5) 7.6(0,53) 18 x 18(5,5 x 5,5) 18(5,5) 21(79,5) 7.6(0,53) 21(79,5) 7.6(0,53) beams 4¼ to 8(108 to 203) us- ng F2 escutcheon, 4 to 8(100 20 x 20(6,1 x 6,1) 20 (6,1) 23 (87,1) 9.2(0,63) 23 (87,1) 9.2(0,63) to 203) using El escutcheon For Ceiling types refer to NFPA 13, 13R or 13D Model Fl Res 30, 49, 58 & 76 CCP Pendent* * Not listed for corrosion resistance. 2 5/8" [66.7mm] DIA. 2 5/16" 0/A. - - I-IDLE IN CEILING [58. 7mm1 CUP - 1I/2" IlEQUCEf? CEILING 7A 1/4 /1.5mmj MAX.FITTING J TO FACE OF CEILING DIMENSION COVER ADJUSTMENT HEIGHT 3 51 " 0/4. 1J5FC04E [84. 1mm] Fl RES 30, 49, 58 & 76 COP PEND. Fig. 3 Note: The Fl Res 76 will use a 1" x %" reducer. CCP Cover Plate Data: "A" Cover Adjustment "B" CCP Height "C', Deflector Distance below bottom Inch (mm) Inch (mm) of m inch (mm) 1/2 (127) 15/16 (24) h/2(13) 1(25.4) 5//5 (7,9) 3A(19) 1/2 (13)1(254) Model Fl Res 30, 49, 58 & 76 Recessed Pendent / FP FP push-on/thread-off escutcheon 2 5/8" 0/A. [66. 7mm] —HOLE IN CEILING - 2 5/75" 01.4. - [58 7mm] CUP - L - " X 7/2" RED TIGER I,- / CEILING 11/2' f58.immi \ iflifln1 FACE OFFITTINC 9 TO FACE OF C 1/2" [13mm] MAX PP ADJUSTMENT _ ......... _____________ Fl RES 49 PENDENT/FP Fig. 4 FP Escutcheon Data: "B" FP Position "A" Deflector Distance below bottom Inch (mm) of beam Inch (mm) Max. Recessed 7/16 (11) ½(12.7) Mm. Recessed 15/16(24) 1 (25.4) - Note: Sprinklers shown in Fig. 3 and Fig. 4 are not suitable for installation in ceilings which have positive pressure in the space above. 4. Technical Data: Fl Res 30 CCP Pendent and Recessed Pendent/FP (SIN R3511) ThreadNO.M CCP Assembly Temp. Rating Max. K Sprinkler I Orifice 1 PSizeressure Ambient Temp. Length Factor °F Inch (mm) 1/2"NPT 2i/, (8.2) 175 (12) 135 57 100 38 3.0 (43.2) 2.25 (57) Ordinary Temp. Rating Max. Coverage area Max. Spacing (15.5°F./68°C) Top of Deflector to Ceiling Minimum Ft x Ft (m x m) Ft (m) Inch (mm) Spacing Flow Pressure .............. . ........ .................. .......LJmm) 12 X 12 (3,6 X 3,6) 12(3,6) --.- 8(30.3) 7.0 (0.48) .P ar Smooth Ceilings 1/210 1(13 to 25.4) using CCR 1/2 to 1(13 to 25.4) using FP escutcheon. Beamed Ceilings per NFPA 13D, 13R or 13 installed in 8(2,4) 14 x 14 (4,3 x 4,3) 14(4.3) 11(37,8) 13.4(0,92) beams 1/210 1(13 to 25.4) using COP. ½ to 1(13 to 25.4) using FP escutcheon. For Ceiling types refer to NFPA 13, 13R or 13D Technical Data: Fl Res 49 CCP Pendent and Recessed Pendent/FP (SIN 3516) Nominal CCPMax. Assembly Ambient K Thread Orifice Sprinkler Pressure Size Inch . Temp. Factor Length psi (bar) ating mm, Inch (mm) OF °C OF IOC 11"NPT (8/2) 1/1c" (11) 175 (12) 135 57 100 38 4.9 (70.6) 2.25 (57) Max. Coverage Ordinary Temp. Rating Minimum area Max. Spacing °C (155°) F/68 Top of Deflector to Ceiling fl Spacing Ft x Ft 'm x m' Ft (m) Flow Pressure Inch (mm) Ft m / GPM (1/mm) PSI (bar) 12 x 12(3,6 x 3,6) 12(3,6) 13(49) 7.0 (0,48) Smooth Ceilings ½ to 1(1310 25.4) using 14 x 14(4,3 x 4,3) 14(4,3) 13(49) 7.0(0,48) CCP. 1/210 1(131025.4) using FP escutcheon. 16 x 16 (4,9 x 4,9) 16(4,9) 14 (53) 8.2 (0,56) Beamed Ceilings per NFPA 13D, 13R or 13 installed in beams ½ to 1(13 to 25.4) using 8(2,4) 18 x 18(5,5 x 5,5) 18(5,5) 18(68.1) 13.5 (0,93) COP. ½ to 1(13 to 25.4) using FP escutcheon. 720 x 20(6,1 x 6,1) 20(6,1) 20 (75,7) 16.7 (1,14) For Ceiling types refer to NFPA 13, 13R or 13D Technical Data: F1 Res 58 CCP Pendent and Recessed Pendent/FP (SIN R3513) Thread Nominal Max. CCP Assembly Max. Sprinkler K Size Orifice Pressure Temp. Rating Ambient Temp. Length Factor °F °C °F C . Inch (mm) psi (bar) Inch (mm) 1/2"NFT /2(13) 175(12) 135 57 100 38 5.8(83.5) 2.25 (57) Max. Coverage Ordinary Temp. Rating Minimum area Max. Spacing (155°F/68°C) Top of Deflector to Ceiling Ft x Ft (m x m) Ft (m) Inch (mm) Spacing Ft (m) Flow Pressure GPM (1/mm ) PSI (bar) 12 x 12(3.6 x 3,6) 12(3,6) 16(61) 7.6(0,53) Smooth Ceilings ½ to 1(13 to 25.4) using COP. 1/2 to 1(13 to 25.4) using FP escutcheon. 14 x 14 (4,3 x 4,3) 14(4,3) 16 (61) 7.6 (0,53) 16 x 16(4,9 x 4,9) 16(4,9) 16(61) 7.6 (0,53) Beamed Ceilings per NFPA 13D, 13R or 13 installed in beams 1/210 1 (13 to 25.4) using COP. 1/2101(131025.4) using FP escutcheon. 8(2,4) 18 x 18(5,5 x 5,5) 18(5.5) 19(72) 10.8(0,75) 20x20(6,1 x6,1) 20(6,1) 22 (83,3) 14.4(1,0) For Ceiling types refer to NFPA 13, 138 or 130 5. Technical Data: F1 Res 76 CCP Pendent and Recessed PendentlFP (SIN R7618) Thread Nominal Max. CCP Assembly Max. K Sprinkler Size Orifice Pressure Temp. Rating Ambient Temp. Factor Length OF °C OF °C Inch (mm) psi (bar) Inch (mm) 3/4"NPT 17/" (13.5) 175(12) 135 57 150 66 7.6 (1 09 2.25 (57) Max. Coverage Ordinary Temp. Rating Minimum area Max. Spacing (1550 -C) Top of Deflector to Ceiling Spacing Flow Pressure Ft x Ft 'm x m' Ft (m) Inch (mm) Ft m . ......................................................... 12 x 12(3,6 x 3,6) 12(3,8) 21(79,5) 7.6 (0,53) Smooth Ceilings 1/2 to 1(13 to 25.4) using CCP. '/2 to 1(13 to 25.4) using FP escutcheon. 14 x 14(4,3 x 4,3) 14(4,3) 21(79,5) 7.6(0,53) 16 x 16 (4,9 x 4,9) 16(4,9) 21(79,5) 7.6 (0,53) Beamed Ceilings per NFPA 13D, 13R or 13 installed in beams ½ to 1(13 to 25.4) using OCR 8(2,4) 18 x 18 (5,5 x 5,5) 18(5,5) 22 (83,3) 8.4(0,58) ½ to 1(131025.4) using FP escutcheon. 20x20(6,1 x6,1) 20(6,1) 25(94,6) 10.8 (0,74) For Ceiling types refer to NEPA 13, 13R or 13D ' Model Fl Res 44 & 58 H r FACE OF FITTING TO II - I 1/4 MIN. [31.8mm] I WALL DIMENSION I -2 1/4" HOLE 0/A. [57.2mm] CEILING TO [3.2mm] DEFLECTOR 1 Xi /2" REDUCER DIMENSION 1 15/16" DIA.)P4_.. 27/32" 0/A [49.2 m]. T1 , [72.2mm] TURN COLLAR UNTIL TIGHT AGAINST SPRINKLER WRENCH BOSS. y [1-m]135F606-D ADJUSTMENT Fl RES 58 & 44 HSW/F2 Fig. 5 Technical Data: Fl Res 44 HSW & HSW/F2 (SIN R3531) Model Fl Res 44 & 58 Recessed HSWIF2 F2 escutcheon, 1/2" (13mm) adjustment Nominal Max. Sprinkler Max. Sprinkler Thread Size Orifice Pressure Temp. Rating _________ - Ambient Temp. ________ K Factor Length Inch (mm) psi (bar) Inch (mm) OF OC OFOc ½" NPT (R½) _____ 3/s" (10) 175(12) 155 175 68 79 100 38 150166 4.4(63) 2.45(62) Escutcheon, F2, Data: Face of Fitting Adjustment Type to wall Inch (mm) Inch (mm) F2 1 1/2.(13) (4.7-17.4) Max. Coverage area Ft x Ft (m x m) Max. Spacing i Ft (m) _____ Ordinary Temp. Rating (155°F/68°C) Intermediate Temp. Rating (175°F179°C) Top of Deflector to Ceiling Inch (mm) PSI (bar) Minimum Spacing Ft (m) Flow GPM (L/m) Pressure PSI (bar) Flow GPM (1/mm) Pressure 12 x 12(3,6 x 3,6) 12(3,6) 12 (45.4) 7.5 (0,52) 12(45,4) 7.5(0,52) 4 to 6(100 to 152); /2 (13) recessed using F2 escutcheon 8(2,4) 14 x 14(4,3 x 4,3) 14(4,3) 14(53,0) 10.2 (0,71) 14(53,0) 10.2 (0,71) 16 X 16(4,9 X 4,9) 16(4,9) 16(60.6) 13.3(0,92) 16(60,6) 13.3 (0,92) 16 x 18(4,9 x 5,5) 16(4,9) 18(68,1) 16.8(1,16) 18(68,1) 16.8 (1,16) 18 x 18(5,5 x 5,5) 71 18(5,5) 19(72,0) 18.7(1,29) 19(72,0) 18.7 (1,29) 16 x 20(4,9 x 6,1) 16(4,9) 23(87,1) 27.4(1,89) 23(87,1) 27.4 (1,89) 12 x 12(3,6 x 3,6) 12(3,6) 14(53,0) 10.2(0,71) 14(53,0) 10.2(0,71) 6 t 12 (152 to 305); ½(13) recessed using F2 escutcheon 14 x 14 (4,3 x 4,3) 14(4,3) 16(60,6) 13.3(0,92) 16(60,6) 13.3(0,92) 16 x 16(4,9 x 4,9) 16(4,9) 17(64,4) 15.0 (1,04) 17(64,4) 15.0 (1,04) 16 x 18 (4,9 x 5,5) 16(4,9) 20(75,7) 20.7(1,43) 20(75,7) 20.7 (1,43) 16 x 20(4,9 x 6,1) 16(4,9) 23 (87,1) 27.4 (1,89) 23 (87,1) 27.4 (1,69) For Ceiling types refer to NFPA 13, 13R or 130 Technical Data: F1 Res 58 HSW & HSW/F2 (SIN R3533) Escutcheon, F2, Data: Nominal Max Sprinkler Max. Sprinkler . Face of Fitting e Temp. Rating Ambient Length Type AdJUmeflt wall Thread Orifice PressurSize (mm) In Inch psi (bar) In to P.Factor Inch ch (mm) (mm) OF °C OF °C (mm) - ½"NPT 155 ~ 68 100 38 2"(13) 45(62) F2 1/2 (13) (4.7-17.4) 175(12) 5.8(83.5) 2.175 79 150 66 Ordinary Temp. Rating Intermediate Temp. Rating Max. Coverage area Max. Spacing (155°F/68C) (175°F/79°C) Top of Deflector to Minimum Ft x Ft (m x m) Ft (m) Ceiling Spacing Flow Pressure Flow Pressure GPM (1/mm) PSI (bar) GPM (L/min) PSI (bar) Inch (mm) Ft (m) 12 x 12(3,6 x 3,6) 12(3,6) 16(60,6) 7,6 (0,53) 16(60,6) 7.6 (0,53) 4106(100to 152); 1/2 (13) recessed using F2 escutcheon 14 x 14(4,3 x 4,3) 14(4.3) 18(68,2) 9.7 (0,69) 18(68,2) 9.7 (0,69) 16 x 16(4,9 x 4,9) 16(4,9) 21(79,5) 13.2(0,91) li 21(79,5) 13.2 (0,91) 16 x 18(4,9 x 5,5) 16(4,9) 25 (94,7) 18.6 (1,28) 1 25 (94,7) 18.6 (1,28) 8(2,4) 16 x 20 (4,9 x 6, 1) 16(4,9) 29 (1098) 25.0(1,73) . 29(109.8) 25.0(1,73) 12 x 12 (3,6 x 3,6) 12(3,6) 22(83,3) 14.4(1,0) 22(83,3) 14.4(1,0) 610 12 (152 to 305); ½(13) recessed 14 x 14(4.3 x 4.,3) 14(4,3) 22 (83,3) 14.4 (1,0) 22 (83,3) 14.4 (1,0) ...........- ........._..... 16 x 16(4,9 x 4,9) 16(4,9) 26 (98,4) 20.1 (1,39) 26 (98,4) 20.1 (1,39) using F2 escutcheon 16 18 (4,9x 5,5) 16(4,9) 31(117,4) 28.6(1,97) 31(117,4) 28.6 (1,97) For Ceiling types refer to NFPA 13, 13R or 130 7. Model Fl Res 44 SWC Tcrhnk'.I flit F:i Rp4t 1o1 SW( 1IFJ P2i 4I2" [7O.,m D I I/4 [3I,75,Ro,] U ,n ipu F 0/ Fit/Ng To Wolf Dimension PUSH ON COVER, THEN ADJUST TO ADJUST UNTIL TIGHT AGAINST WALL. I X I/2 Reducer A [84] TURN COLLAR UNTIL lIGHT AGAINST SPRINKLER 21132' WRENCH BOSS. f4 17-1 I35FG07 2- [12.70mml Adjustment El RES 44 SWC Nominal Max. Cover Max. Sprinkler Thread Orifice Pressure Temp. Ambient K Length Size Inch (mm) psi (bar) Rating Temp. Factor Inch (mm) IOC OFIOC 1/2 NPT s/a" (10) 175(12) (R½)_____ f135 57 100 38 4.4 (63) 2.45(62) Max. Coverage area Ft x Ft (m x m) Ordinary Temp. Rating Max. Spacing (155°F/680C) Ft (m) Flow Pressure GPM (1/mm) i PSI (bar) Top of Deflector to Ceiling Inch (mm) Minimum Spacing Ft (m) 12 x 12(3,6 x 3,8) 12(3,6) 13(49,2) 8.7 (0,60) 4 to 6 (100 to 152); ½ (13) recessed using F2 escutcheon 8(2,4) 14 x 14(4,3 x 4,3) 14(4,3) 14(53,0) 10.2 (0,71) 16 x 16(4,9 x 4,9) 16(4,9) 17(64,3) 15,0(1,1) 16 x 18 (4,9 x 5,5) 16(4,9) 19(71.8) 18.7(1.13) 16 x 20(4,9 x 6,1) 16(4,9) 23(87,1) 27.4(1,89) 12x 12(3,6x3,6) 12(3,6) 14(52,9) 10.2(0,71) 6 t 12(152t0305); 1/2 (13)recessed using F2 escutcheon 14x 14(4,3x4,3) 14(4,3) 15(56,7) 11.7(0,81) 16 x 16(4,9 x 4,9) 16(4,9) 18 (68,1) 16.8 (1,16) 16 x 18(4,9 x 5,5) 16(4,9) 20 (75,6) 20.7 (1,43) For Ceiling types refer to NFPA 13, 138 or 13D 91 Mrs,11 C1 O UCAIV f0-161 RR,.,1i WD* IJAIV (I Technical Data: Fl Res 58 HSWX (SIN RA3533) Thread Nominal Max. Sprinkler Max. Ambient K Sprinkler Sprinkler Size Orifice Pressure Temp. Rating Temp. Factor Length Identification Inch (mm) psi (bar) Inch (mm) Number (SIN) 0F Bulb ½ NPT (RY2) 1(13) 175 (12) 155 175 68 79 100 150 38 66 5.8(83.5) 2.45 (62) RA3533 Max. Coverage area Ft x Ft (m x m) ________________ - Max. Spacing Ft (m) ___________ - Ordinary Temp. Rating (155°F/680C) Intermediate Temp. Rating (175°F179°C) Top of Deflector to Ceiling Inch (mm) Minimum Spacing Ft (m) Flow GPM (Llmin) Pressure PSI (bar) Flow GPM (Llmin) Pressure PSI (bar) 18 x 20(5,5 x 6,1) 18(5,5) 30 (114) 26.8(1,85) 30(114) 26.8(1,85) 4t06(100to 152); ½ (13) recessed using F2 escutcheon 8(2,4) 20 x 20(6,1 x 6,1) 20(6,1) 30(114) 26.8(1,85) 30(114) 26.8 (1,85) 16 x 22 (4,9 x 6,7) 16(4,9) 33(125) 32.4 (2,23) 33(125) 32.4 (2,23) 16 x 24 (4,9 x 7,3) 16(4,9) 38(144) 42.9 (2,96) 38(144) 42.9(2,96) 14 x 26(4,3 x 7,9) 14(4,3) 42(160) 52.4 (3,75) 42(160) 52.4 (3,75) 18 x 20 (5,5 x 6,1) 18(5,5) 35 (133) 36.4 (2,5) 35(133) 36.4 (2,5) 6 to 12 (152 to 305); ½ (13) recessed using F2 escutcheon 16 x 22 (4,9 x 6,7) 16(4,9) 38(144) 42.9(2,96) 38(144) 42.9(2,96) 16 x 24 (4,9 x 7,3) 16(4,9) 42(160) 52.4 (3,6) 42(160) 52.4 (3.6) 14 x 26(4,3 x 7,9) 14(4,3) 46(174) 62.9 (4,34) 46(174) 62.9 (4,34) For Ceiling types refer to NFPA 13, 13R or 13D —................-..--1 17/16" VIN. [37.8mm] 1/8 "A' r - CEILING TO KSI[3.2/nm] DEFLECTOR DIMENSION - - 2 27/32" 0/A. [72.2mm] I/F [13mm] ADJUSTMENT /5)/TN COLLAR L/N7/L T/GPIT AGAINST SF/V/I/F/LEN WRENCH BOSS. 7)5/CO/I FACE OF ArT/NC TO WALL 0/MEN/V/ON 2 1/4" HOLE 0/A. [57.2mm! 1" X 7/2' F//VOL/CE/V ¶ 149.2m "I I Fl RES 58 HSWX Fig. 7 Eel Technical Data: KRes58 HSWX (RA3593) Thread Nomi l nal oax. Max. x. Ambient K Sprinkler Sprinkler Orifice Size ____________________________________________________________________________________________________ Pressure Temp. Factor Length Identification Inch (mm) psi (bar) Inch (mm) Number (SIN) OFIOC NPT =Unk (R1/2) I 1/2" (13) 175(12) 100 38 5.8(83.5) _________ 2.45(62) 3593 Ordinary Temp. Rating Top of Deflector to Max. Coverage area Max. Spacing (165°F/740C) Minimum Ceiling Spacing flow Pressure Ft x Ft (mx m) R (m) Inch (mm) Ft (m) PSI (bar) 18 x 20 (5,5 x 6, 1) 18(5,5) 29(109) 25(1,72) 4106(100 to 152); 20x20(6,1 x6,1) 20(6.1) 30(114) 26.8(1,85) 16 x 22(4,9 x 7,3) 16(4,9) 33(125) 32,4(2,23) ½ (13) recessed using F2 escutcheon 16 x 24 (4,9 x 7,3) 16(4,9) 38 (144) 42.9 (2,96) 8(2,4) 14 x 26 (4,3 x 7,9) 14(4,3) 42(160) 52.4(3,75) 18 x 20(5,5 x 6,1) 18(5,5) 35(133) 36.4 (2,5) 6 to 12 (152 to 305); ½ (13) Recessed 16 x 22(4,9 x 6,7) 16(4,9) 38(144) 42.9(2,96) 16 x 24(4,9 x 7,3) 16(4.9) 42(160) 52.4(3,6) using F2 escutcheon 14 x 26(4,3 x 7,9) 14(4,3) 46(174) 62.9(4,34) For Ceiling types refer to NFPA 13, 13R or 13D Maintenance Model Fl Res 30, 49, Fl Res 58, Fl Res 76 and Fl Res 44 Sprinklers should be inspected and the sprinkler sys- tem maintained in accordance with NFPA 25, 13, 13D, and 13R. Do not clean sprinkler with soap and water, Am- monia or any other cleaning fluids. Remove dust by using a soft brush or gentle vacuuming. Remove any sprinkler which has been painted (other than factory applied) or damaged in any way. A stock of spare sprinklers should be maintained to allow quick replacement of damaged or operated sprinklers. Prior to installation, sprinklers should remain in the original cartons and packaging until used. This will minimize the potential for damage to sprinklers that could cause improper operation or non-operation. Model Fl Res 30, 49 & 58 Pendent Sprinkler Specifications Sprinklers shall be [cULus Listed] [New York City MEA Approved (258-93-E)] low flow residential pendent sprin- klers engineered to provide a minimum design density of 0.05 gpm/ft2 over the listed coverage area. Listed flows as specified by the manufacturer's technical data sheets are to be used. Residential sprinklers shall be installed in conformance with the manufacturer's installation guide- lines and the applicable installation standard. Deflector- to-ceiling distance listing shall be 1" to 8" maximum, only for FlRes 49. Sprinkler frame and deflector shall be of bronze frame construction having a ½" NPT thread. Wa- ter seal assembly shall consist of a Teflon* coated Bel- leville spring washer with top-loaded extruded or cold head cup with 3 mm glass bulb containing n: plastic parts, and having a temperature rating of [155°F (68°C)] [175°F (790C)]. Sprinklers shall have a nominal K-factor of 3.0, 4.9 and 5.8. Standard finish: [Bronze] [Chrome- plated] [White Polyester] [Spe.ial finish- specify]. Resi- dential pendent sprinklers shall be Reliable Model Fl Res 30, 49 & 58, SIN R351 1, R3516 & R3513 (Bulletin 135). Model Fl Res 49 & 58 Recessed Pendent/Fl, Model Fl Res 30, 49 & 58 Recessed Pendent/ F2, Model Fl Res 30,49 & 58 Recessed Pendent/ FP Sprinklers shall be [cULus L-sted] [New York City MEA Approved (258-93-E)] low flow residential recessed pen- dent sprinklers engineered to provide a minimum design density of 0.05 gpm/ft2 over the listed coverage area. Listed flows as specified by the manufacturer's technical data sheets are to be used. Residential sprinklers shall be installed in conformance witi the manufacturer's in- stallation guidelines and the applicable installation stan- dard. Deflector-to-ceiling distance listing shall be 1" to 8" maximum, only for F1 Res 49. Spinkler frame and deflec- tor shall be of bronze frame construction having a ½" NPT thread. Water seal assembly shall consist of a Teflon* coated Belleville spring washer with top-loaded extruded *DuPont Registered Trademark 10. or cold head cup with 3 mm glass bulb containing no plastic parts, and having a temperature rating of [155°F (68°C)] [175°F (791C)]. Sprinklers shall have a nomi- nal K-factor of 3.0, 4.9 & 5.8. Standard finish: [Bronze] [Chrome-plated] [White Polyester] [Special finish- spec- ify]. Recessed escutcheon assembly shall be a steel, two-piece escutcheon [with ½' adjustment (Model F2)] [with 34" adjustment (Model Fl)] [of push-on and thread off design with ½" adjustment (Model FP)]. Standard fin- ish shall be [brass][bright chrome] [white painted]. Resi- dential recessed pendent sprinklers shall be Reliable [Model Fl Res 30, 49 & 58 Recessed Pendent/F1] [Model Fl Res 30. 49 & 58 Recessed Pendent/F2] [Model Fl Res 30, 49 & 58 Recessed Pendent/FP] SIN R351 1 R3516 & R3513 (Bulletin 135). Model Fl Res 30, 49 & 58 CCP Pendent (Concealed) Sprinklers shall be [cULus Listed] [New York City MEA Approved (258-93-F)] low flow residential concealed sprinklers engineered to provide a minimum design den- sity of 0.05 gpm/ft2 over the listed coverage area. Listed flows as specified by the manufacturer's technical data sheets are to be used. Residential sprinklers shall be in- stalled in conformance with the manufacturer's installa- tion guidelines and the applicable installation standard. Sprinkler frame and deflector shall be of bronze frame construction having a ½." NPT thread. Water seal as- sembly shall consist of a Teflon* coated Belleville spring washer with top-loaded extruded or cold head cup with 3 mm glass bulb containing no plastic parts, and having a temperature rating of 155°F (680C). Cover plate assem- bly shall consist of a brass cover plate and copper alloy retainer flange. Method of attaching the cover plate to the sprinkler cup shall be a push-on and thread-off design allowing a ½" cover plate adjustment. Cover plate tem- perature rating shall be 135°F (57°C). A plastic protec- tive cap shall be provided and factory installed inside the sprinkler cup to protect the sprinkler from damage, which could occur during construction before the cover plate is installed. Standard cover plate finish: [White] [Custom Color- specify]. ]. Concealed pendent sprinklers shall be Reliable Model Fl Res 30, 49 & 58 CCP, SIN R3511, R3516 & R3513 (Bulletin 135). Model Fl Res 44, Fl Res 58 Horizontal Sidewall, Fl Res 58 HSWX & KRes58 HSWX Residential Sprinkler Specifications Sprinklers shall be [cULus Listed] low flow residential horizontal sidewall sprinklers engineered to provide a minimum design density of 0.05 gpm/ft2 over the listed coverage area. Listed flows as specified by the manu- facturer's technical data sheets are to be used. Residen- tial sprinklers shall be installed in conformance with the manufacturer's installation guidelines and the applicable installation standard. Sprinkler frame and deflector shall be of bronze frame construction having a 1/2" NPT thread. Water seal assembly shall consist of a Teflon coated Bel- "DuPont Registered Trademark leville spring washer with top-loaded extruded or cold head cup with 3 mm glass bulb containing no plastic parts, and having a temperature rating of [155°F (68°C)] [175°F (790C)]. The solder element (Link) version, the water seal consist of a cap with a bellville spring washer and a temperature rating of 165°F (74°C). The recessed assembly forthe HSWX (Bulb & Link) should be a steel two pieces escutcheon with 1/2" adjustment (Model F2) standard finish should be Bright Chrome and white paint- ed. The Fl Res 58 HSW is also available with low lead frame. Fl Res 58 HSW and HSWX sprinklers shall have a nominal K Factor of 5.8 and Fl Res 44 a nominal K factor of 4.4. Standard finish: [Bronze] [Chrome-plated] [White Polyester] [Special finish- specify]. Residential horizontal sidewall sprinklers shall be Reliable Model Fl Res 44, Fl Res 58, Fl Res 58 HSWX & Model KRes58 HSWX, SIN R3531, RA3533 & RA3593 (Bulletin 135). Model Fl Res 44 Recessed Horizontal Sidewall Sprinkler Use description for the Model Fl Res 44 horizontal side- wall sprinkler with the following modifications: Replace "horizontal sidewall sprinkler" with "recessed horizontal sprinkler." Add: Recessed escutcheon assembly shall be a steel, two-piece escutcheon with 1/2" adjustment (Model F2). Standard finish shall be [brass][bright chrome] [white painted] [Special finish- specify]. Residential recessed horizontal sidewall sprinklers shall be Reliable Model Fl Res 44/F2, SIN R3531 (Bulletin 135). Model Fl Res 76 Pendent Sprinklers shall be [cULus Listed] low flow residential pendent sprinklers engineered to provide a minimum design density of 0.05 gpm/ft2 over the listed coverage area. Listed flows as specified by the manufacturer's technical data sheets are to be used. Residential sprin- klers shall be installed in conformance with the manufac- turer's installation guidelines and the applicable installa- tion standard. Sprinkler frame and deflector shall be of bronze frame construction having a 3%" NPT thread. Wa- ter seal assembly shall consist of a Teflon* coated Bel- leville spring washer with machined or cold head cup with 3 mm glass bulb containing no plastic parts, and having a temperature rating of [155°F (680C)] [175°F (790C)]. Sprinklers shall have a nominal K-factor of 7.6. Standard finish: [Bronze] [Chrome-plated] [White Polyester] [Spe- cial finish- specify]. Residential pendent sprinklers shall be Reliable Model Fl Res 76, SIN R7618 (Bulletin 135). Model Fl Res 76 RecessedPendentfFl, Model Fl Res 76 Recessed Pendent/F2, Model Fl Res 76 Recessed Pendent/FP Sprinklers shall be [cULus Listed] low flow residential recessed pendent sprinklers engineered to provide a minimum design density of 0.05 gpmlft2 over the listed coverage area. Listed flows as specified by the manu- facturer's technical data sheets are to be used. Residen- tial sprinklers shall be installed in conformance with the manufacturer's installation guidelines and the applicable installation standard. Sprinkler frame and deflector shall be of bronze frame construction having a 3/4" NPT thread. Water seal assembly shall consist of a Teflon* coated Bel- leville spring washer with machined or cold head cup with 3 mm glass bulb containing no plastic parts, and hav- ing a temperature rating of [155°F (68°C)] [175°F (79°C)]. Sprinklers shall have a nominal K-factor of 7.6. Standard finish: [Bronze] [Chrome-plated] [White Polyester] [Spe- cial finish- specify]. Recessed escutcheon assembly shall be a steel, two-piece escutcheon [with ½" adjust- ment (Model F2)] [with 34" adjustment (Model Fl)] [of push-on and thread off design with 1/2" adjustment (Mod- el FP)]. Standard finish shall be [brass][bright chrome] [white painted]. Residential recessed pendent sprinklers shall be Reliable [Model Fl Res 76 Recessed Pendent/ Fl] [Model Fl Res 76 Recessed Pendent/F2] [Model Fl Res 76 Recessed Pendent/FP] SIN R7618 (Bulletin 135). Model Fl Res 76 CCP Pendent (Concealed) Sprinklers shall be [cULus Listed] low flow residential concealed sprinklers engineered to provide a minimum design density of 0.05 gpm/ft2 over the listed coverage area. Listed flows as specified by the manufacturer's technical data sheets are to be used. Residential sprin- klers shall be installed in conformance with the manufac- turer's installation guidelines and the applicable installa- tion standard. Sprinkler frame and deflector shall be of bronze frame construction having a 3%" NPT thread. Wa- ter seal assembly shall consist of a Teflon* coated Bel- leville spring washer with machined or cold head cup with 3 mm glass bulb containing no plastic parts, and having a temperature rating of 155°F (680C). Cover plate assem- bly shall consist of a brass cover plate and copper alloy retainer flange. Method of attaching the cover plate to the sprinkler cup shall be a push-on and thread-off design allowing a 1/2" cover plate adjustment. Cover plate tem- perature rating shall be 135°F (57°C). A plastic protec- tive cap shall be provided and factory installed inside the sprinkler cup to protect the sprinkler from damage, which could occur during construction before the cover plate is installed. Standard cover plate finish: [White] [Custom Color- specify]. 1. Concealed pendent sprinklers shall be Reliable Model Fl Res 76 CCP, SIN R7618 (Bulletin 135). Finishes (1) Standard Finishes Sprinkler F1,F2,FP Cover Plates Escutcheons —..---...., .... ......... . Bronze Brass White Painted Chrome Plated Bright Chrome Plated Chrome White and Black White Painted Polyestert2 Coated Special Application Finishes Sprinkler Fl, F2, FP Escutcheons Electroless Nickel PTFE(Teflon(")12) Electroless Nickel PTFE (Teflon's) Bright Brass Bright Brass Black Plated Black Plated Black Paint Black Paint Off White Off White Chrome Dull Chrome Dull 1) Other finishes and colors are available on special order. Consult factory for details. (2) cULus listed Corrosion Resistant Note: Paint or any other coating applied over the Factory finish will void all approvals and warranties. Ordering Information Specify: Sprinkler Model Sprinkler Type Temperature Rating Sprinkler Finish Escutcheon Finish Cover Plate Finish DuPont Registered Trademark The equipment presented in this bulletin is to be installed in accordance with the latest published Standards of the National Fire Protection Association, Factory Mutual Research Corporation, or other similar organizations and also with the provisions of governmental codes or ordinances whenever applicable. Products manufactured and distributed by Reliable have been protecting life and property for over 90 years, and are installed and serviced by the most highly qualified and reputable sprinkler contractors located throughout the united States, Canada and foreign countries. Manufactured by Reliable Automatic Sprinkler Co., Inc. Recycled - -(800) 431-1588 Sales Offices 'apor Relia Die (800) 848-6051 Sales Fax (914) 829-2042 Corporate Offices Revision lines indicate updated or new data. www.reliablesprinkler.com Internet Address EG. Pn:ed in U.S.A. 06/15 P/N 9999970235 SENJU SPRINKLER CO.,LTD.171 Residential Lead Free Flat Concealed Sprinkler. Pendent. Model: RC-RES, K-Factor: 4.9. SIN: SS8464 GENERAL DESCRIPTION The Model RC-RES Residential Flat Concealed Sprinklers are automatic sprinklers of the compressed fusible solder type. These are decorative and fast response. The Cover Plate Assembly hides the Deflector, Heat Responsive Element etc., which is in turn concealed above the ceiling. The cover plate has a flat profile, and its diameter is extremely small (2-5/8 inch, 68mm). The push-on and/or thread-on, thread-off design of the concealed cover plate assembly allows easy installation of the cover plate. Therefore, the Model RC-RES should be your first choice when aesthetics is the major consideration for ultimate appeal and unbeatable performance is desired. The Model RC-RES is designed for the residential occupancies and it is perfect for use in homes, hotels and other living quarters. The Model RC-RES is to be used in wet pipe residential sprinkler systems for One- and Two- Family Dwellings and Manufactured Homes per NFPA 13D; wet pipe residential sprinkler systems for Residential Occupancies up to and Including Four Stories in Height per NFPA 13R; or, wet pipe sprinkler systems for the residential portions of any occupancies per NFPA 13. The Model RC-RES has a 4.9 (70.6 LPM/bar112) K-factor that meets the required residential flow rates with minimal residual pressure, which allows for smaller pipe sizes and water supply requirements. For extended installation flexibility, the Model RC-RES provides 1/2 inch (12.8mm) vertical adjustment. This adjustment in installation decreases the need for precise cutting of the pipe that drops to the sprinkler and allows for a perfect fit with a range of pipe lengths. The heat sensitivity and water distribution design of Model RC-RES allows for an increased chance of residents' escape or evacuation in case of fire. However, residential fire sprinkler systems are not a substitute for fire safety awareness or fire safety construction required by building codes. "Lead Free" is defined in the Reduction of Lead in Drinking Water Act (S.3874) endorsed by AWWA's Water Utility Council, and California Assembly Bill #1953 as having less than or equal to a weighted average of 0.25% lead in wetted surface of pipes, plumbing fittings and fixtures. WARNINGS The Mode! RC-RES must be installed and maintained in accordance with the rules stated herein as well as in compliance with the applicable standards of the National Fire Protection Association regulations and the standards of any other authorities having jurisdiction. In the event of this condition, consult the authorities having jurisdiction for guidance and approval. Failure to do so may impair the integrity of these devices. It is the responsibility of the installing contractor to provide a copy of this document to the owner or his representative, and in turn, it is the obligation of the owner to provide a copy of this document to a succeeding owner. The owner is responsible for maintaining their fire protection system and devices in proper operating condition. The installing contractor or sprinkler manufacturer should be contacted with any related questions. Document No. U085160 Date Feb/09/2015 OPERATION Page .• 2 of 8 2- i'í'° (0 52mm) Marking Lot No. CIL Year of Manufactue SIN 5S8464 —K—factor 44.9 Tempeiature Rating 162</72C • UL Mark or 1 75°F/79'C Control No, 6P37 its NSF Mark NSF-61---C s RES SPKR KD Body (Copper 5Jloy) ® Deflector (Phosphorus Bronze) K Gasket (PTFE) ® Fusible Metal Solderl Heat Collector (Capzr) 2-%"( 68mm) e Cover Plate 4ssomy or 3-Y"(83mm) or 2- %"square (068mm) FIGURE 1. Model RC-RES K4.9 Color Code M,rkicg SIN SS84t K—th<tor 1<4.9 neera1ure Raerg I 6.uF/72C or 175F/79c —UL Hark COVER PLATE SPRINKLER (Top view) (Bottom view) FIGURE 1-1. Markinci (Color Code) TECHNICAL DATA Approvals: cUL.. Listed, NSF-61-G Sprinkler Identification Number (SIN): SS8464 Maximum Working Pressure: 175psi (12.1bar) Discharge Coefficient (Nominal K-Factor): K4.9 GPM/psi112 (70.6 LPMIbar1°2) Temperature Rating: 162°F (72°C) Sprinkler with 140°F (60°C) Cover Plate 175°F (79°C) Sprinkler with 162°F (72°C) Cover Plate Color Code (Sprinkler) 162°F (729C): Uncolored 175°F (790C): White Color Code (Cover Plate) 140°F (60°C): No Mark 162°F (729C): White-Colored Mark Vertical Adjustment: 112 inch (12.8 mm) Cover Plate Finishes: Standard Finishes- White, Ivory, Beige, Brown, Black, Nickel, Wood Grain Custom Finishes- Custom color and custom pattern cover plates are available on special order. Contact a Senju Sprinkler representative with any custom orders. Please see chart on Page 8 for more detail. Physical Characteristics: Ref. Figure II In case of fire, the spider component that holds together the Cover Plate and the Retainer melts. Then, the Cover Piate is released at once. As a result, the Deflector drops down to the intended position. Two Heat Collectors are exposed to fire, and when sufficient heat from the fire is recorded, internal componens of the sprinkler to fall apart. This leads to allow :he water flow to be distributed on the affected by fire area. (Ref. Figure 2) Normal Condition Cover P ate Operation Sprinkler Opeation Water Discharge FIGURE 2. OPERATION PROCESS (The figure is for illustrative purpose only) Document No. U085160 Date : Feb/09/2015 Page 3 of 8 DESIGN CRITERIA The herein stated rules for use and installation of Model RC-RES are provided by the manufacturer and must be strictly implemented for safe and full results. NOTES Residential Fire Sprinkler Systems should only be designed and installed by individuals who are completely familiar with automatic sprinkler system design, installation procedures, and techniques. Several criteria may apply to the installation and usage of each sprinkler. Consequently, it is recommended that the sprinkler system designer review and develop a working understanding of the complete list of criteria prior to initiating the design of the sprinkler system. Questions concerning sprinkler installation and usage criteria, which are not coverage by the following instructions, should be submitted to Contact Company. Include sketches and technical details as appropriate. In some instances, the requirements of this document may concern specifications which are more stringent and which take precedence over those specified in NFPA 13, 13D, 13R, or by the authority having jurisdiction. The Model RC-RES must not be used in applications where the air pressure above the ceiling is greater than that below. Inspect all sprinklers after installation to ensure that both the gap between the cover plate, ceiling and the 6 slots in the cup are open and free from any air flow impediment. The spray from the sprinkler is distributed radically outward and downward from the sprinkler deflector. Consequently, the sprinklers must be located such that there will be no blind spaces shielded from spray by partitions, room dividers, overhangs or other parts of the dwelling structure. The number of sprinklers within each compartment (as defined by NFPA 13, 13D, or 13R) must be kept as small as possible. Do NOT use more sprinklers than necessary to cover a particular space. Use only the Cover Plate provided with the Model RC-RES. The sprinkler must be secured in place by firmly fastening the sprinkler system piping to the structure. If the sprinkler is not properly secured in position, reaction forces resulting from sprinkler operation could alter its orientation and its water distribution pattern. Obstruction to Water Distribution Locations of sprinklers must follow the obstruction rules of NFPA 13 for Residential Sprinklers. General Service Conditions The Model RC-RES must only be utilized in WET PIPE sprinkler systems. Heat Source Criteria Refer to NFPA 13D or 13R for the requirements relating to the prevention of possible activation of the Heat Responsive Element of Model RC-RES, due to exposure to a heat sources other than an actual fire. Precautionary Warnings for Corrosive Environments The Model RC-RES should not be installed where they may be subjected to a corrosive environment including the following: Chlorine ion and Chloride environment. Stress corrosion cracking may be caused by exposure to environments with Chlorine ion and Chloride. Exposure to this environment may result in sprinklers operating under Non-Fire conditions or Not Operating when exposed to an actual fire. Sprinkler system piping with Copper. Sprinkler systems should be constructed in compliance with the applicable standards and the requirements for the copper piping when copper piping is used in the sprinkler system. (Reference standards NFPA 13, ASTM B813, B828, and CDA (Copper Development Association) - Solder Joint) All residual flux must be removed from the interior and exterior of copper piping by thoroughly flushing before installation of the Sprinkler Heads. Otherwise, residues of flux may cause corrosion and leakage in the sprinkler system. Hydraulic Design Criteria The minimum required sprinkler flow rates for system designed to NFPA 13D or 13R are given in Table A as a function of temperature rating and the maximum allowable coverage areas. The sprinkler flow rate is the minimum required discharge from the most hydraulically demanding sprinkler from each of the total number of "design sprinklers" as specified in NFPA 13D or 13R. For systems designed to NFPA 13, the number of designed sprinklers is to be the four most hydraulically demanding sprinklers. The minimum required discharge from each of the four sprinklers is to be the greater of the followings; The flow rates given in Table A for NFPA 13D and 13R as a function of temperature rating and maximum allowable coverage area. Document No. U085160 Date Feb/09/2015 Page : 4 of 8 A minimum discharge O.IGPM/sq.ft. [4.07LPM/sq.m] over the "design area" comprised of the four most hydraulically demanding sprinklers for the actual coverage areas being protected by the four sprinklers. TABLE A. NFPA 13D & 13R WET PIPE HYDRAULIC DESIGN CRITERIA for Model SS8464 Maximum Ordinary Intermediate Coverage Maximum Temperature Rating Temperature Rating Deflector Minimum Area(a) Spacing 162°F (72°C) 175°F (79°C) to Installation Spacing Flow Pressure Flow (b) Pressure (b) Ft. x Ft. Ft. Ceiling Type Ft. (m xm) (m) GPM PSI GPM PSI (m) (LPM) (bar) (LPM) (bar) Smooth 12x12 12 13 7.0 13 7.0 Ceilings (3.7x3.7) (3.7) (49.2) (0.48) (49.2) (0.48) 3/8 to 7/8 Inches. 1014 14 13 7.0 13 7.0 Beamed (4.3x4.3) (4.3) (49.2) (0.48) (49.2) (0.48) Ceilings per NFPA 16x16 16 13 7.0 14 8.2 13D,13R Concealed 8 (4.9x4.9) (4.9) (49.2) (0.48) (53.0) (0.57) or 13 (2.4) Installed in beam 18x18 18 17 12.0 18 13.5 3/8 to (5.5x5.5) (5.5) (64.3) (0.83) (68.1) (0.93) 7/8 inches 20x20 20 21 18.4 below (6.1x6.1) (6.1) (79.5) (1.27) - - bottom of beam. For coverage area dimensions less than the above mentioned, it needs to use the minimum required flow for the Next Higher Coverage Area listed. Requirement is based on minimum flow in GPM/LPM from each sprinkler. The associated residual pressures are calculated using the nominal K-Factor. Refer to Hydraulic Design Criteria Section for details. For systems with ceiling types smooth flat horizontal, or beamed, or sloped, in accordance with the 2013 Edition of NFPA 13D, 13R or 13 as applicable. Sprinkler Spacing Criteria The minimum spacing between sprinklers is 8 feet (2.4m). The maximum spacing between sprinklers cannot go beyond the coverage area calculated by using the specific hydraulic factors. (Ref. Table A) INSTALLATION The Model RC-RES must be installed in accordance with the following instructions. NOTES Do not use any sprinklers which have been subjected to potential mechanical damage. Do not use any sprinklers which, show deformation or cracking in either the Sprinkler or the Protective Cap. Prior to installation, sprinklers should be maintained in the original cartons and packaging until used to minimize the potential for damage to sprinklers that would cause improper operation or non-operation. The Protective Cap must remain on the sprinkler during installation and until the ceiling installation is completed. The Protective Cap must be removed to place the sprinkler in service. Document No. U085160 Date . Feb/09/2015 Page 5 of 8 Use a torque of 7 to 14 ft.lbs (9.5 to 19.0Nm) to achieve a 1/2 inch NPT sprinkler joint. If you exceed the recommended maximum torque, this could result in damage to the sprinkler inlet, which may lead to leakage from the sprinkler. In case of insufficient adjustment in Cover Plate installation, do not try to overly tighten, screw the sprinkler too loosely or make any modification to the cover plate assembly. Readjust the sprinkler fitting fora better M. Installinci Procedure Step I The installation requirements for the sprinkler are as follows: to be installed only in the pendent position with the waterway perpendicular to the ceiling. Install the sprinkler fitting so that the distance from the face of the fitting to the mounting surface will be nominally 2 inch (50.8mm) as shown in Figure 3. Step 2 With pipe thread sealant applied to the threads, hand tighten the sprinkler into the sprinkler fitting. Then tighten it with the Sprinkler Socket or Wrench & Socket Combination (Ref. Figure 4). The grooves of the Socket must fit perfectly with the grooves on the Sprinkler for proper installation (Ref. Figure 4). Step 3 If desired the Protective Cap may also be used to locate the center of the clearance hole by gently pushing the ceiling material against the center point of the Protective Cap. Before the installation of the ceiling, the sprinkler installation can be started with the 2-3/8 inch (60mm) diameter clearance hole (Ref. Figure 3). Use the "Tolerance Limit of Ceiling Level" indicator on the Protective Cap to check for proper installation height (Ref. Figure 3). Make a Space Here Do NOT JAve. Y4" (6.4mm) Over-Tighten G roove inkler Mm Ye' (3.2mm) Tolerance Limit (Ceirvq ceiling Mounting Surface Moul-Kra Surface et nch2- Y," (6Omm) Ceifog Hole Diameter CORRECT ________ FIGURE 3. INSTALLATION FIGURE 4 Step 4 Use the Cap Remover RC to remove the Protective Cap (Ref. Figure 5), and then push or screw a Cover Plate Assembly on the Cup of the Sprinkler by hand until its flange just comes in contact with the ceiling (Ref. Figure 6 and Figure 7). Stop tightening the Cover Plate Assembly once the flange has come in contact with the ceiling. If the ceiling has been lifted from its normal position in the process of tightening of the Cover Plate Assembly, readjust the cover plate assembly as necessary. If the flange of the Cover Plate Assembly cannot come in contact with the ceiling sufficiently, readjust the sprinkler fitting as necessary. When properly installed, there is a nominal 1/16 inch (1.6mm) air gap between the lip of the Cover Plate and the ceiling, as shown in Figure 6 Document No. U085160 Date : Feb/09/2015 Page 5 of SprHkler Head Ca Cc emoverR Step Hook by turning Step 3 Pull down FIGURE 5. PROTECTIVE CAP REMOVAL Document No. U085160 Date Feb09/2015 CARE AND MAINTENANCE Page 7 of 8 The following instructions must be implemented for the maintenance and service of the Model RC-RES. NOTES Wet pipe sprinkler systems must be maintained at a minimum temperature of 40 T14 1C to prevent freezing and bursting of the pipe and/or sprinklers. Automatic sprinklers are not to be tested with a heat source. Operation of the heat responsive element can result. Absence of a Cover Plate Assembly may delay the response time of the sprinkler in case of fire. Install the cover plate assembly property, as shown in Figure 6. Improper installation of the cover plate assembly may cause improper operation or non-operation. If the ceiling is to be repainted after the installation of the Sprinkler, care must be exercised to ensure that the new paint does not seal off any of the air gap. Factory painted Cover Plates must not be repainted. They should be replaced, if necessary, by factory painted cover plates. Non-factory applied paint may adversely delay orpre vent sprinkler operation in case of a fire. Do not pull the Cover Plate. Separation may result. In preparation for maintenance of the fire protection system, permission to close the main control valve must be obtained from the proper authorities and all affected by this action parties must be informed before the maintenance session can commence. Do NOT enclose any sprinklers within drapes, curtains, or valances. Do NOT hang anything from the sprinklers. Do NOT clean the sprinklers with soap and water, detergents, ammonia, cleaning fluids, or other chemicals. Remove dust, lint, cobwebs, cocoons, insects, and larvae by gently brushing with a feather duster or gently vacuuming with a soft bristle (i.e., dusting) brush attachment. Exercise suitable safety precautions in the use and storage of highly flammable materials. The rapid rate of fire development and spread of these materials can reduce the ability of the sprinkler systems to aid in the control of a fire involving such hazards. Leaking or corroded sprinklers must be replaced. Automatic Sprinklers must never be shipped or stored where the temperature exceeds lOOT /38°C. Automatic sprinkler must never be physically altered, such as painted, plated, or coated, once shipped from the factory. If the sprinklers have been in any way modified, they must be replaced. Great caution must be applied to prevent damage to the sprinklers at all stages - before, during, and after installation. Damaged units, as a result of dropping, hitting, over-tightening, or wrench slippage, must be replaced. The Model RC-RES must only be replaced with pendent sprinklers which are listed for residential fire protection service and which have the same nominal K-Factor, the same coverage area, and the same or lower flow ratings (as indicated under Table A "Hydraulic Design Criteria"). When remodeling, such as by adding false beams or light fixtures or changing the location of compartment walls, first verity that the new construction will not violate the installation requirements of the applicable standards of NFPA. Alter the new construction and/or the sprinkler system to suit the requirements of this document and the applicable NFPA regulations. The owner is responsible for the maintenance of the sprinkler system, including inspection and testing, its compliance with this documents, as well as the standards of the National Fire Protection Association (e.g., NFPA 25), and the regulations of any other authorities having jurisdiction. The owner should direct any questions regarding the above rules and regulations to the installing contractors or the sprinkler manufacturer. It is recommended that automatic sprinkler systems be inspected, tested, and maintained by a qualified Inspection Service in accordance with NFPA 25. Document No. U085160 Date : Feb/09/2015 ORDER PROCEDURE Page 8 of 8 When placing an order, please contact a local distributor with the following information (Model Name, Specify, Temp. and Finish). Sprinkler: Model: RC-RES (SIN: SS8464, Residential Flat Concealed Sprinkler, Pendent, K4.9, Temperature: 162T (72°C) or 1757 (79°C)) Cover Plate Assembly: 2-5/8 inch (68mm) or 3-1/4 inch (083mm) or 2-5/8 inch square (068mm), Order Separately from Sprinkler Please refer to the chart below for available sizes, temperature, and finishes. Standard Finishes Custom Finishes White Ivory Beige Brown Black Nickel Wod grain Custom Color Custom Pattern 2-5/8' Round, 140°F 0 0 - - - 0 - 0 0 3-1/4' Round, 140°F 0 0 0 0 0 0 0 0 0 2-5/8" Square, 140°F 0 - - - - - 0 0 2-5/8" Round, 162°F 0 - - - - - - 0 0 3-1/4" Round, 162°F 0 - - - - - - 0 0 Tools for Installation of Model: RC-RES Socket for Model RC-RES Wrench & Socket for Model RC-RES Cap Remover RC Document No. U085160 Date : Feb/09/2015